We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal-organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (¯201) orientation peaks of -Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 x1018 cm-3 and mobility of ~770 cm2V-1s-1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance-voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 x1013 cm-2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV-1. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.

Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

This study introduces a gate design that uses pass transistor switches and enables the implementation of all nec- necessary logic gates with a single structure. This gate design can be used for efficient circuit resizing and creating secure obfuscated circuits. This work also presents simulation results that demonstrate the effectiveness of the gate in performing various logic gate operations.

Doping can alter the electronic and thermoelectric attributes of an organic semiconductor system. These alterations can enable viable tunable devices that have applications in temperature sensing for environmental controls. Here we demonstrate a dual-modulation organic field-effect transistor (OFET) where temperature effectively modulates the current-voltage characteristics of the OFET and gate voltage modulates the thermoelectric properties of the active layer. Poly(3-hexylthiophene-2,5-diyl) (P3HT) was utilized as the host donor polymer, iodine was utilized as the dopant acceptor molecule Finished devices were characterized by a semiconductor analyzer system with temperature controlled by two thermoelectric cooling plates. The doping of iodine in the range of 0.25% to 0.5% mole ratio with respect to the P3HT exhibited the greatest on-off ratio of the investigated dopant concentrations. Iodine doping concentrations of 0.5% mole ratio or less can greatly improve the thermoelectric properties of a binary P3HT-based system and the current-voltage performance of the dual-modulation device.

The electronic transport stability in nanodevices composed by metal/trans-polyacetylene /metal with different long length has contributed greatly for performance, homogeneity, stability, organization of the chains, reproducibility and higher conductivity. In this paper, we present an analytical study of the electronic transport characteristics from dimerized trans-polyacetylene (trans-PA) molecules containing an odd-even number of sites coupled to metal leads (left and right) in T-shaped geometry using the extended Su-Schrieffer-Heeger (SSH) model based on tight-binding Hamiltonian with the Non-Equilibrium Green´s Function (NEGF) via Heisenberg´s equation of motion and the Keldysh´s formalism. Due to the complexity of the T-shaped odd-even chain, our proposal was to test the effects on the finite-length network for three, four, five sites and furthermore foresee for 17-sites. We show how to tune dimerization strength () coupling to the parameters and T-shaped geometry of the device to which it affects the overlap integral localized at the three endpoints of the T-shaped system, making both the odd and even chains to undergo a metal-insulator transition in their electronic behavior. The results reached through control parity of the chain plane of the parameters governing () the electronic and experimental tunneling allow a better understanding of the subject.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Protein tyrosine sulfation (PTS), a vital post-translational modification, facilitates protein–protein interactions and regulates many physiological and pathological responses. Monitoring PTS has been difficult owing to the instability of sulfated proteins and the lack of a suitable method for detecting the protein sulfate ester. In this study, we combined an in situ PTS system with an ultra-high-sensitivity polysilicon nanowire field-effect transistor (pSNWFET)-based sensor to directly monitor PTS formation. A peptide containing the tyrosine sulfation site of P-selectin glycoprotein ligand (PSGL)-1 was immobilized onto the surface of the pSNWFET by using 3-aminopropyltriethoxysilane and glutaraldehyde as linker molecules. A coupled enzyme sulfation system consisting of tyrosylprotein sulfotransferase and phenol sulfotransferase was used to catalyze PTS of the immobilized PSGL-1 peptide. Enzyme-catalyzed sulfation of the immobilized peptide was readily observed through the shift of the drain current–gate voltage curves of the pSNWFET before and after PTS. To the best of our knowledge, this is the first study to describe in situ PTS and its direct observation by using semiconductor devices. We expect that this approach can be developed as a next generation biochip for biomedical research and industries.

Many advanced technologies have been employed in the high performance active matrix displays including liquid crystal displays, organic light emitting diode displays, and micro light emitting diode displays. On the other side, there have existed the strong demand on the cost reduction and it is one of low cost schemes to integrate the driver circuit in a panel based on thin film transistor technologies. This paper reviews overall concept, operation principles, and various circuit approaches in shift registers for the scanning pulse generation. In addition, it deals with the implementation of additional functionalities in gate drivers to support pixel compensation, multi-line driving, in-cell capacitive touch screen, pixel sensing, and adaptive scanning region control.

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

Solar radiation impacts diverse aspects of city life, such as harvesting energy with PV panels, passive heating of buildings in winter, cooling loads of air-conditioning systems in summer, and urban microclimate. Urban digital twins and 3D city models can support solar studies in the process of urban planning and provide valuable insights for data-driven decision support. This study examines the calculation of solar incident radiation at the city scale in Sofia using remote sensing data for the large shading context in a mountainous region and 3D vector building data. The building footprints and the terrain are preprocessed using GIS. The solar calculation uses a raytracing algorithm in 3D CAD at the city scale. To evaluate the performance, two cases were considered at the city and district scale, respectively. The total face count of meshes for the simulations constituted approximately 2 000 000 faces. 64379 roofs for the whole city and 4796 buildings for one district were selected. All calculations were performed in one batch and visualized in a 3D web platform. Using a 3D CAD environment establishes a seamless process of updating 3D models and simulations while preprocessing in GIS ensures working with large-scale datasets. The proposed method showed moderate computation time for both cases and could be extended to include reflected radiation and dense photogrammetric meshes in the future.

Traversal time in tunneling effect for ultrasonic waves in tapered waveguides is derived considering its analogy with quantum and electromagnetic waves tunneling. If, as traversal time, the so called phase time is considered, the ultrasonic wavepacket shows the equivalent in acoustics of superluminality i.e. the derived velocity , crosses the limit of bulk transverse ultrasonic waves in the medium of the waveguide that is the equivalent of c in the quantum and electromagnetic cases. Graphs clearly illustrating this so called Hartman effect are obtained confirming the experimental results in the three different fields.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

The research on the impact of excavation of underpass tunnels has already had certain results, but there is a lack of research cases of double-line highway tunnels with oblique angles underpass the existing railway tunnels, especially the method of determining the area of the impact of the dynamic and static loads of the new tunnels and existing trains to be enriched by considering them at the same time. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel with oblique angles underpass the Hurong Railway in Wanshoushan. By constructing a three-dimensional finite element model and simulating the application of static tunnel excavation load, dynamic blasting load and dynamic train operation load of the existing tunnel, the overall displacement of the existing tunnel and the settlement value of the bottom plate of the track surface by the static tunnel excavation load were analyzed. Then, the stresses, vibration speeds and displacements of the tunnel due to the dynamic blasting loads and the dynamic train operation loads were obtained. The results show that: the area of influence of the static loads of the new tunnel excavation on the existing tunnel is divided into three types of perturbations presenting strong, weak and slight; the area affected by the blasting dynamic load of new tunnel excavation is a circular domain with the datum point in the tunnel section as the center; the area affected by the dynamic load of train operation in the existing tunnel is an ellipse with the center of the track surface of the existing tunnel as the datum; there is an anomalous shape in the area affected by the blasting dynamic load of new tunnel excavation and the area affected by the dynamic load of train operation in the existing tunnel.

Abstract: Rationale. Object tracking has significance in many applications ranging from control of unmanned vehicles to autonomous monitoring of specific situations and events, especially when providing safety for patients with certain adverse conditions such as epileptic seizures. Conventional tracking methods face many challenges, such as the need for dedicated attached devices or tags, influence by high image noise, complex object movements, and intensive com-putational requirements. We have developed earlier computationally efficient algorithms for global optical flow reconstruction of group velocities that provide means for convulsive seizure detection and have potential applications in fall and apnea detection. Here, we address the chal-lenge of using the same calculated group velocities for object tracking in parallel. Methods. We propose a novel optical flow-based method for object tracking. It utilizes real-time image se-quences from the camera and directly reconstructs global motion-group parameters of the con-tent. These parameters can steer a rectangular region of interest surrounding the moving object to follow the target. The method successfully applies to multi-spectral data, further improving its effectiveness. Results. Experimental results on simulated tests and complex real-world data demonstrate the method's capabilities. The proposed optical flow reconstruction can provide accurate, robust, and faster results compared to current state-of-the-art approaches.

This paper presents the design and implementation of a multichannel bio-impedance spectroscopy system on field programmable gate arrays (FPGA). The proposed system is capable of acquiring multiple signals from multiple bio-impedance sensors, process the data on the FPGA and store the final data in the on-board Memory. The system employs the Digital Automatic Balance Bridge (DABB) method to acquire data from biosensors. The DABB measures initial data of a known impedance to extrapolate the value of the impedance for the device under test. This method offers a simpler design because the balancing of the circuit is done digitally in the FPGA rather than using an external circuit. Calculations of the impedance values for the device under test were done in the processor. The final data is sent to an onboard Flash Memory to be stored for later access. The control unit handles the interfacing and the scheduling between these different modules (Processor, Flash Memory) as well as interfacing to multiple Balance Bridge and multiple biosensors. The system has been simulated successfully and has comparable performance to other FPGA based solutions. The system has a robust design that is capable of handling and interfacing input from multiple biosensors. Data processing and storage is also performed with minimal resources on the FPGA.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

Abstract— Flight Control System is an integrated avionics system equipped with the minimum required components for an autonomous flight. This paper focuses on the Hardware Design of the Flight Control System and presents specific details of the components and its interface. The system architecture is based on Field Programmable Gate Array and Digital Signal Processor. Employing these two processors in the flight control system would improve the Flight Control System performance in terms of fast sequential processing of high-level control algorithms. In addition to Field Programmable Gate Array and Digital Signal Processor, the flight control computer system will also make use of Global Positioning System and Micro Electro Mechanical System sensors. The project will be implemented using Altera’s System On Programmable Chip builder, currently known as Qsys – Platform Designer implemented in Quartus-II. The system employs Nios-II processor which is 32-bit soft-core embedded-processor architecture designed especially for the Altera’s family of Field Programmable Gate Array. From conceptualization to final design, this paper presents the functionality of the different modulus and complex interfaces employed in this Flight Control System.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

This paper explores indigenous perspectives on the understanding and management of cultural heritage within the Mapungubwe and Makgabeng Cultural landscapes in South Africa. State-based management system paid little attention to indigeneity resulting in contested interpretation of the archaeological past. This by-passing of indigenous input is a product of colonial and apartheid policies that glorified Western practices at the expense of black African heritage stakeholders. World heritage mechanisms are also skewed in favor of modern practice which is overly designed to be sensitive to tangible aspects of the past than the intangible elements that make up much of indigenous African heritage. We used the archaeology of Mapungubwe and Makgabeng Cultural landscapes as a test case for the impact of indigenous voices on heritage, but the results have wider applicability. We employed semi-structured interviews and focus group discussions to gather qualitative data that we calibrated with our lived experiences as products of Tsonga-speakers from this broader landscape. The results expose that indigenous people use physical manifestation of sites, ethnographic inquiry, names, oral history, spirit mediums, landscape memory, genealogy, and praise poetry to identify, interpret, evaluate, and manage their cultural heritage. Additionally, indigenous perspectives which rely on collective memory, ritual practices, and indigenous knowledge systems have huge potential for enriching our understanding of the archaeological heritage. We propose a more inclusive archaeology and heritage management practice that involve indigenous groups in the identification, interpretation, grading, and presentation of the African past.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Alzheimer’s disease is a debilitating neurodegenerative condition which is known to be the most common cause of dementia. Despite its rapidly growing prevalence, medicine still lacks a comprehensive definition of the disease. As a result, Alzheimer’s disease remains neither preventable nor curable. In recent years, broad interdisciplinary collaborations in Alzheimer’s disease research are becoming more common. Furthermore, such collaborations have already demonstrated their superiority in addressing the complexity of the disease in innovative ways. However, establishing effective communication and optimal knowledge distribution between researchers and specialists with different expertise and background is not a straightforward task. To address this challenge, we propose the Alzheimer’s disease Ontology for Diagnosis and Preclinical Classification (AD-DPC) as a tool for effective knowledge sharing in interdisciplinary/multidisciplinary teams working on Alzheimer’s disease. It covers six major conceptual groups, namely Alzheimer's disease pathology, Alzheimer's disease spectrum, Diagnostic process, Symptoms, Assessments, and Relevant clinical findings. All concepts were annotated with definitions or elucidations and in some cases enriched with synonyms and additional resources. The potential of AD-DPC to support non-medical experts is demonstrated through an evaluation of its usability, applicability and correctness. The results show that the participants in the evaluation process who lack prior medical knowledge can successfully answer Alzheimer’s disease-related questions by interacting with AD-DPC. Furthermore, their perceived level of knowledge in the field increased leading to effective communication with medical experts.

This research investigates the effect of pre-soaking treatment on plant-based aggregate using a wet grout binder to formulate a high-strength lightweight concrete (HSLWC). The surface modification utilising a novel grout soaking technique with various water-to-cement (w/c) ratios indicated a new method of approach for the recent development of lightweight plant-based aggregate (LWPA). In this experiment, the fresh and hardened properties of modified LWPA lightweight concrete were assessed by verifying their workability, densities, compressive and split tensile strengths towards the modulus of elasticity. The results showed that pre-soaking plant-based lightweight aggregate (w/c: 0.6, 0.8, 1.0, and 1.2) slightly increased the density of the samples compared to untreated LWPA. The oven-dry density of treated and untreated LWPA is controlled in the range of HSLWC. The outcomes indicated that the workability of the surface- modified LWPA has significant improvement up to 40% in 6 min for (TDS)/0.6 sample compared to the original LWPA. The mechanical properties of the LWPA concrete with surface modification method exhibit substantial increment of compressive strength, split tensile strength, and modulus of elasticity were recorded at 22%, 26%, and 34%, respectively. Significantly, the findings from this scientific method revealed that the pre-soaking treatment method on LWPA has shown to be a highly recommended technique in improving interfacial bonding while performing as one of the most promising solutions to improve the properties of lightweight concrete.

Deep learning methods have been widely used in PolSAR image classification. To learn the polarimetric information, many deep learning methods expect to learn high-level semantic features from original PolSAR data. However, only original data cannot learn multiple scattering features and complex structures for extremely heterogeneous terrain objects. In addition, deep learning methods always cause edge confusion due to the high-level features. To overcome these shortages, we propose a double-channel CNN network combined with an edge-preserving MRF model(DCCNN-MRF) for PolSAR image classification. Firstly, to combine complex matrix data and multiple scattering features together, a double-channel convolution network(DCCNN) is developed, which consists of a Wishart-based complex matrix and multi-feature subnetworks. The Wishart-based complex matrix network can learn the statistical characteristics and channel correlation well, and the multi-feature network can learn high-level semantic features well. Then, a unified network framework is designed to fuse two kinds of features to enhance advantageous features and reduce redundant ones. Finally, an edge preserving MRF model is designed to combine with the DCCNN network. In the MRF model, a sketch map-based edge energy function is designed by defining adaptive weighted neighborhood for edge pixels. Experiments are conducted on four real PolSAR data sets with different sensors and bands. Experimental results demonstrate the effectiveness of the proposed DCCNN-MRF method.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

Amidst worsening climate change, drought stress imperils global agriculture, jeopardizing crop yields and food security, necessitating urgent exploration of sustainable methods like biopriming, harnessing beneficial microorganisms to bolster plant resilience. Recent research has revealed diverse biological compounds with versatile applications produced by Schizophyllum commune, rendering this fungus as a promising contender for biopriming applications. For the first time this study aimed to investigate,the potential of S. commune exo- (EPSH) and intra-PSH (IPSH), isolated from two strains: Italian (ITA) and Serbian (SRB) under submerged cultivation, in enhancing the resilience of Pisum sativum L. seeds through biopriming technique. Testing of seed quality of bioprimed, hydroprimed, and unprimed seeds was done using a germination test, under optimal and drought conditions. In optimal conditions, the IPSH SRB increased germination energy by 5.50% compared to the control, while the highest percentage of germination (94.70%) was shown after biopriming with PSH isolated from the ITA strain. Additionally, all assessed treatments resulted in a boost in seedling growth and biomass accumulation, where the ITA strain demonstrated greater effectiveness in optimal conditions, whereas the SRB strain showed superiority in drought conditions. The drought tolerance indices increased significantly in response to all examined treatments during the drought, with EPSH ITA (23.00%) and EPSH SRB (24.00%) demonstrating the greatest effects. Results demonstrate a significant positive influence of fungal PSH, indicating their potential as biopriming agents and offers insights into novel strategies for agricultural resilience in the face of changing environmental conditions.

Tunnel-interchange connecting sections pose significant safety challenges on mountainous expressways due to their high incidence of accidents. Improving road safety necessitates a comprehensive understanding of driver behavior in such areas. This study explores the influences of road characteristics, signage information volume, and traffic conditions on drivers' car-following and lane-changing behavior in tunnel-interchange diverging areas. Utilizing driving data from 25 subjects of 72 simulated road models, driving performance is assessed using Friedman rank test and multivariate variance analysis. The results highlight the significant influence of both connection distance and signage information load on driving behavior. In tunnel-interchange scenarios, the reduction of velocity increased by 62.61%, and speed variability surged by 61.11%, indicating potential adverse effects on driving stability due to the environmental transitions. Decreased connection distances are associated with reduced lane-changing durations, larger steering angles, and increased failure rates. Furthermore, every two units increase in signage information leads to a 13.16% rise in maximum deceleration and a 5% increase in time headway. Notably, the signage information volume shows a significant interaction with connection distance (F=1.60, P=0.045) for most car-following indicators. Hence, the study recommends a maximum connection distance of 700 m and signage information not exceeding nine units for optimal safety and stability.

Research shows that in earthquakes the ground response changes in areas where there are underground cavities. Due to the fact that subways and underground tunnels pass from beneath buildings in urban areas, these changes in ground response have a direct impact on the seismic behavior of structures. In this study, first by model validity and reliability of the results, steel structures modeling was conducted and steel structure behavior was evaluated due to Tunnel-Soil-Structure seismic interaction. Parameters studied are number of stories, soil type, tunnel depth, horizontal tunnel-structural distance and dynamic loading. Considering that one of the most important parameters of structural control is drift and story displacement, so this important factor will be considered. The results show that tunneling has a direct effect on the rate of structural displacement and increases the structural response. Also, the behavior of the structure is affected by the position of the structure at the ground level and the position of the tunnel and this should be considered during the design phase of the structures.

We presented unusual case of double left ventricular false aneurysm complicating late presentation AMI successfully treated with the combination of urgent surgical drainage of tamponade, staged PCI of non-culprit lesion, preventive implantation of ICD-DR, guideline directed heart failure medical therapy and delayed but effective reconstructive operation.

The horizontal flatbed electrophoresis system has been used for the electrophoresis of protein samples and is often preferred for a two-dimensional polyacrylamide gel electrophoresis. In currently available equipment, cathode and anode electrodes were placed on top of a gel at each end. An electric field entered from the top of a gel, and its strength was relatively weaker in the bottom part of the gel. Such configuration caused migrating protein bands to lie down forward in the migrating direction. New electrodes, i.e., the clamp-shaped and the double-deck electrodes, were developed to simultaneously apply an electric field from the top and bottom of a gel. Electrophoretic separation with these electrodes made protein bands more focused and improved protein band resolutions. When the FIGE technique was tested together with new electrodes, protein bands were aligned nearly vertically and showed the best electrophoretic resolutions.

In the current pilot study, we attempt to find out how double neurofeedback influences functional hemispheric asymmetry and activity. We examined 30 healthy participants (8 males; 22 females, mean age = 29; SD= 8). To measure functional hemispheric asymmetry and activity, we used computer laterometry in the ‘two-source’ lead-lag dichotic paradigm. Double biofeedback included 8 minutes of EEG oscillation recording with five minutes of basic mode. During the basic mode, the current amplitude of the EEG oscillator gets transformed into feedback sounds while the current amplitude of alpha EEG oscillator is used to modulate the intensity of light signals. Double neurofeedback did not directly influence the asymmetry itself but accelerated individual sound perception characteristics during dichotic listening in the preceding effect paradigm. Further research is needed to investigate the effect of double neurofeedback training on functional brain activity and asymmetry taking into account participants’ age, gender, and motivation.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

In this paper, we investigate the Hawking radiation process by using the quantum tunneling phenomenon of massive spin-1 (W-bosons) and spin-0 particles from (2+1) dimensional Black Hoke with quintessential and magnetic field. For this purpose, using Hamilton-Jacobi ansatz, we apply the WKB approximation to the field equations of massive charged vector particles. We get the required tunneling rate of radiated particles and obtain their corresponding Hawking temperature $T_h$. In order to study the quantum gravity effects, we utilize the generalized Proca and Klein-Gordan equations incorporating the generalized uncertainty principle (GUP) and recover the accompanying quantum corrected temperature $T'_{h}$.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

We study theoretically the Josephson diode effect (JDE) realized in a system composed of parallel-coupled double quantum dots (DQDs) sandwiched between two semiconductor nanowires deposited on an s-wave superconductor surface. Due to the combined effects of the proximity-caused superconductivity, strong Rashba spin-orbit interaction and Zeeman splitting inside the nanowires, a pair of Majorana bound states (MBSs) may possibly emerge at opposite ends of each nanowire. Different phase factors arisen from the superconductor substrate can be generated in the coupling amplitudes between the DQDs and MBSs prepared at the left and right nanowires, and will result in the Josephson current. We find that the critical Josephson currents in positive and negative directions are different from each other in amplitude within an oscillation period with respective to the magnetic flux penetrating through the system, a phenomenon known as the JDE. It arises from the quantum interference effect in this double-path device, and can hardly occur in system of one QD coupled to MBSs. Our results also show that the diode efficiency can reach up to 50%, and depends on the overlap amplitude between the MBSs and the energy levels of the DQDs adjustable by gate voltages. The present model is realizable within current nanofabitication technologies and may find practical use in interdisciplinary field of Majorana and Josephson physics.

Zeta potential refers to the electrokinetic potential present in colloidal systems, exerting significant influence on the diverse properties of nano-drug delivery systems. The impact of dielectric constant on the zeta potential and charge inversion of highly charged colloidal particles, immersed in a variety of solvents spanning from polar, such as water, to nonpolar solvents, and in the presence of multivalent salts, was investigated through primitive model Monte Carlo (MC) simulations. Zeta potential ξ is decreased as decreasing the dielectric constant of the solvent, and upon further increase in the salinity and the valency of the salt. At elevated levels of salt, the colloidal particles become overcharged, in all solvents. As a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity, as a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity.

The scheme to realize high speed (~250Gb/s) all-optical Boolean logic gates using semiconductor optica amplifiers with quantum-dot (QD-SOA) is introduced and analyzed in this review. Numerical simulation method was presented by solving the rate equation and taking into account nonlinear dynamics including carrier heating and spectral hole-burning. Binary phase shift keyed (BPSK) signal and on-off keyed signal are used to generate high speed all-optical logic gates. The applications based on all-optical logic gates such as, all-optical latches, pseudo random bit sequence (PRBS) generation and all-optical encryption, are also discussed in this review. Results show that the scheme based on QD-SOA is a promising method for the realization of high speed all-optical communication system in the future.

African trypanosomes are an early branch in eukaryotic evolution and developed a unique endomembrane system as an adaptation to their parasitic life style. The key virulence mechanism of many pathogens is successful immune evasion to enable survival within the host, which is a feature requiring both genetic events and membrane transport in African trypanosomes. Intracellular trafficking not only plays a role in immune evasion, but also in homeostasis of intracellular and extracellular compartments and interactions with the environment. Significantly, historical and recent work has unravelled some of the connections between these processes and highlighted how immune evasion mechanisms associated with adaptations in membrane trafficking may have, paradoxically, provided specific sensitivity to drugs. Here we explore these advances in understanding the membrane composition of the trypanosome plasma membrane and organelles and provide a perspective for how transport could be exploited for therapeutic purpose.

In this exploratory work, we have examined the impact of an external static electric field on the H2 storage capacity of clathrate hydrates. To this end, we have chosen the 512 clathrate hydrate and examined the encapsulation of 1 - 4 H2 molecules within it. Results suggest that with the help of moderate electric fields (±0.10 to ±0.31V/Å), the encapsulation of 1 H2 molecule within the 512 clathrate hydrate becomes thermodynamically more favorable. In the cases of 4H2@512 and 2H2@512, however, the concerned processes become thermodynamically more favorable only when the field is applied along a specific direction. No favorable outcome could be observed in the case of 3H2@512, irrespective of the direction of the applied field. It appears from the results obtained herein that it might be possible to design a suitable external electric field to facilitate the hydrogen storage capacity of clathrate hydrates at ambient conditions, at least in certain cases.

We show that the implementation of the 1/c² transverse current-current interaction between electrons into the standard self-consistent electron BCS model in bulk under thermal equilibrium ensures in the stable superconductive phase the full compensation of a constant external magnetic field by the internal magnetic field created by the electrons i.e. one has an ideal diamagnet. However, no proof of the phenomenological London equation emerges within the bulk approach.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

Neonatal palliative care (NPC) is an integrated and holistic approach that is an integral part of the contemporary neonatal treatment delivery paradigm. It is the highest fulfillment of the notion of beneficence (doing or creating 'good') that has otherwise been neglected/underestimated by the focus of modern medicine on technology and instrumental treatments by its commitment to alleviating patient pain and quality of life. For decades, the Double-Effect Doctrine (DDE) has been used to consider and address a range of ethically questionable circumstances, often at the end of life, including euthanasia, termination of pregnancy to save maternal life, and morally justified warfare. The theory has continued to be mired in controversy as ethicists, legal scholars, theologians, and philosophers discuss the abstract concepts of moral reasoning, purpose, foresight, and other underlying moral theories. In this paper, the moral theory of DDE is discussed in its clinical application to the ethical decision-making process in neonatal palliative and end-of-life treatment, specifically 1) the administration of opioids as required for symptom control and 2) the use of palliative sedation for intractable symptom care.

The circular photogalvanic effect (CPGE) is the photocurrent generated in an optically active material in response to an applied ac electric field, and it changes sign depending on the chirality of the incident circularly polarized light. It is a non-linear dc current as it is second-order in the applied electric field, and for a certain range of low frequencies, takes on a quantized value proportional to the topological charge for a system which is a source of nonzero Berry flux. We show that for a non-interacting double-Weyl node, the CPGE is proportional to two quanta of Berry flux. On examining the effect of short-ranged Hubbard interactions upto first-order corrections, we find that this quantization is destroyed. This implies that unlike the quantum Hall effect in gapped phases or the chiral anomaly in field theories, the quantization of the CPGE in topological semimetals is not protected.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

Molecular transport and quantum tunneling of H2 and H2O molecules through nanoporous gra-phene is studied using computational modeling and first principles density functional theory. It is demonstrated that molecules with sufficiently high kinetic energies can tunnel through the na-nopores. It is also demonstrated that molecules can be trapped in front of the nanopore or behind it. These investigations help us learn the behavior of molecules in and around nanopores of gra-phene. They also help us learn fundamentals of molecular tunneling. We believe, nanoporous gra-phene can play important roles for gas separation and nanofiltration.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

The present study provides an observation and documentation on the effect of static magnetic field on the growth of Triticum aestivum. The seeds are allowed to germinate and the seedlings are grown in an environment of the controlled static magnetic field while other physical factors such as temperature, light exposure, soil pH, etc. are held constant. Also, a comparison of influence on the average height between both the poles of the magnet is estimated and north pole oriented magnet is found to imply a significant difference. Finally some of the potential applications of the study in non-invasive protein silencing, GMO production, Vertical farming and Terraforming are briefly discussed.

We study the light rays in a static and spherically symmetric gravitational field of null aether theory (NAT). To this end, we employ the Gauss-Bonnet theorem to compute the deflection angle by a NAT black hole in the weak limit approximation. Using the optical metrics of the NAT black hole, we first obtain the Gaussian curvature and then calculate the leading terms of the deflection angle. Our calculations show how gravitational lensing is affected by the NAT field. We also show once again that the bending of light stems from a global and topological effect.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

Biochar application to soil has been proposed as a means for reducing soil greenhouse gas emissions and mitigating climate change. The effects, however, of interactions between biochar, moisture and temperature on soil CO₂ and N₂O emissions, remain poorly understood. Furthermore, the applicability of lab-scale observations to field conditions in diverse agroecosystems remains uncertain. Here we investigate the impact of a mixed wood gasification biochar on CO₂ and N₂O emissions from loess-derived soils using: (1) controlled laboratory incubations at three moisture (27, 31 and 35%) and three temperature (10, 20 and 30°C) levels, and (2) a field study with four cropping systems (continuous corn, switchgrass, low diversity grass mix, and high diversity grass-forb mix). Biochar reduced N₂O emissions under specific temperatures and moistures in the laboratory and in the continuous corn cropping system in the field. However, the effect of biochar on N₂O emissions was only significant in the field, and no effect on cumulative CO₂ emissions was observed. Cropping system also had a significant effect in the field study, with soils in grass and grass-forb cropping systems emitting more CO₂ and less N₂O than corn cropping systems. Observed biochar effects were consistent with previous studies showing that biochar amendments can reduce soil N₂O emissions under specific, but not all, conditions. The disparity in N₂O emission responses at the lab and field scales suggests that laboratory incubation experiments are not reliable for predicting the impact of biochar at the field scale.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

This study investigates the electrical characteristics observed in n- channel and p-channel ferroelectric field effect transistor (FeFET) devices fabricated through a similar process flow with 10 nm of ferroelectric hafnium zirconium oxide (HZO) as the gate dielectric. The n-FeFETs demonstrate a faster complete polarization switching compared to the p-channel counterparts. Detailed and systematic investigations using TCAD simulations reveal the role of fixed charges and interface traps at the HZO-interfacial layer (HZO/IL) interface in modulating the subthreshold characteristics of the devices. A characteristic crossover point observed in the transfer characteristics of n-channel devices is attributed with the temporary switching between ferroelectric-based operation to charge-based operation, caused by the pinning effect due to the presence of different traps. This experimental study helps understand the role of charge trapping effects in switching characteristics of n- and p-channel ferroelectric FETs.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

In this paper, we propose a methodology for analyzing the near-field coupling between two surface mount device (SMD) inductors using a 3-dimensional electromagnetic (3D-EM) model. To develop the 3D-EM model, we first extract the effective permeability of core magnetic material in the SMD using the loss tangent in the equivalent circuit model. Then the effective permeability is used in the magnetic material for the 3D-EM modeling of SMD inductor. The validity of the proposed 3D-EM model is confirmed by comparing the impedance and S-parameters obtained from both measured and EM-simulated values for the two near-field coupled SMDs. Finally, the near-field coupling effects between the two adjacent SMD inductors are visualized in terms of magnetic coupling path visualization (CPV) using the proposed 3D-EM model, which demonstrates its usefulness for near-field coupling analysis.

This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

Mapping building roof plane structures is an active research direction in urban-related studies, as understanding roof structure provides essential information for generating highly detailed 3D building models. Traditional deep learning models have been the main focus of most recent research endeavours aiming to extract pixel-based building roof plane areas from remote sensing imagery. However, significant challenges arise, such as delineating complex roof boundaries and invisible boundaries. Additionally, challenges during the post-processing phase, where pix-el-based building roof plane maps are vectorized, often result in polygons with irregular shapes. In order to address this issue, this study explores a state-of-the-art method for planar graph reconstruction applied to building roof plane extraction. We propose a framework for reconstructing regularized building roof plane structures using aerial imagery and cadastral information. Our framework employs a holistic edge classification architecture based on an attention-based neural network to detect corners and edges between them from aerial imagery. Our experiments focused on three distinct study areas characterized by different roof structure topologies: Stadsveld – 't Zwering neighbourhood and Oude Markt area, located in Enschede, The Netherlands, and the Lozenets district in Sofia, Bulgaria. The outcomes of our experiments revealed that a model trained with a combined dataset of two different study areas demonstrated superior performance, capable of delineating edges obscured by shadows or canopy. Our experiment in the Oude Markt area resulted in building roof plane delineation with an F-score value of 0.43 when the model trained on the combined dataset was used. In comparison, the model trained only on the Stadsveld – 't Zwering dataset achieved an F-score value of 0.37, and the model trained only on the Lozenets dataset achieved an F-score value of 0.32. The results from the developed approach are promising and can be used for 3D city modelling in different urban settings.

Cutaneous melanoma (CM) is a candidate for screening programs, since its prognosis is excellent when diagnosed in an early disease stage. Targeted screening of those at high risk for developing CM, a cost-effective alternative to population-wide screening, requires valid procedures to identify the high-risk group. Self-assessment of the number of nevi has been suggested as a component of such procedures, but its validity has not yet been established. We analyzed the level of agreement between self-assessments and expert assessments of the number of melanocytic nevi in the area between the wrist and the shoulder of both arms based on 4548 study subjects in whom mutually blinded double counting of nevi was performed. Nevus counting followed the IARC protocol. Study subjects received written instructions, photographs, a mirror, and a “nevometer” to support self-assessment of nevi larger than 2 mm. Nevus counts were categorized based on the quintiles of the distribution into five levels defining a nevus score. Cohen’s weighted kappa-coefficient was estimated to measure the level of agreement. In the total sample, agreement between self-assessments and expert-assessments was moderate (raw agreement: 50.29%, weighted κ=0.596). Self-assessed nevus counts were higher than those determined by experts (mean differ-ence: 3.33 nevi). The level of agreement was independent of sociodemographic and cutaneous factors; however, participants’ eye color had a significant impact on the level of agreement. Our findings show that even with comprehensive guidance, only a moderate level of agreement between self-assessed and expert-assessed nevus counts can be achieved. Self-assessed nevus information does not appear to be reliable enough to be used in individual risk assessment to target screening activities.

Minirhizotron tubes were installed to monitor root growth dynamics of mature Shiraz grapevines in a rootstock trial established in the hot climate Riverina region of New South Wales, Australia. The vertical root distribution and seasonal root growth dynamics of Shiraz on own-roots and Shiraz grafted on the rootstocks Ramsey, 140 Ruggeri and Schwarzmann was studied for five seasons across a seven-year period to a depth of 60 cm. New root production was significantly influenced by genotype, soil depth, season, growth stage and year. Soil moisture and soil tem-perature were monitored at 10, 30 and 60 cm in the last two seasons. Soil moisture at 30 cm and soil temperature at all three depths were significant predictors of root growth. New root numbers were significantly higher in 140 Ruggeri than the other rootstocks. To the depth studied, 140 Ruggeri roots were evenly distributed from the topsoil down, whereas the majority of roots of Schwarzmann and Shiraz were located at intermediate depths in the 10-40 cm ad 20-40 cm zones respectively, while Ramsey roots were found at 20 cm or below. Depending on genotype, root growth occurred across several phenological stages but tended to peak at flowering. In some years we observed root growth in early and late winter at rates exceeding that of autumn, and this was associated with warmer temperatures during this period. Overall, seasonal rooting dynamics were responsive to abiotic factors but dominated by genotype.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

In this work, we investigate the weak deflection angle of light from exact black hole within the non-linear electrodynamics. First we calculate the Gaussian optical curvature using the optical spacetime geometry. With the help of modern geometrical way popularized by Gibbons and Werner, we examine the deflection angle of light from exact black hole. For this desire, we determine the optical Gaussian curvature and execute the Gauss-Bonnet theorem on optical metric and calculate the leading terms of deflection angle in the weak limit approximation. Furthermore, we likewise study the plasma medium's effect on weak gravitational lensing by exact black hole. Hence we expose the effect of the non-linear electrodynamics on the deflection angle in the weak gravitational field.

We study the effect of polymer coating, pressure, temperature and light on the electrical characteristics of monolayer WSe₂ back-gated transistors with quasi-ohmic Ni/Au contacts. We prove that the removal of a layer of poly(methyl methacrylate) or a decrease of the pressure change the device conductivity from p to n-type. We demonstrate a gate-tunable Schottky barrier at the contacts and measure a barrier height of ~70 meV in flat-band condition. We report and discuss a temperature-driven change in the mobility and the subthreshold slope which we use to estimate the trap density at the WSe₂/SiO₂ interface. We study the spectral photoresponse of the device, that can be used as a photodetector with a responsivity of ~0.5 AW^-1 at 700 nm wavelength and 0.37 mW/cm² optical power.

This study investigated the effects of two plyometric training protocols on sprint and change of direction (COD) performance in elite hockey players. A parallel-group randomized controlled trial design was used and seventeen elite male and female field hockey players were randomly allocated into either low-to-high (L-H, n = 8) or high-to-low (H-L, n = 9) training groups. Each group performed separate variations of the drop jump exercise twice weekly for six weeks, with an emphasis on either jump height (L-H) or drop height (H-L). Performance variables assessed included sprint times over 10 m and 20 m, as well as 505 time. A two-way repeated measures analysis of variance was performed and Cohen’s d effect sizes were calculated. The H-L group displayed significant small ES improvement from baseline to post-training in the 10 m sprint (1.893 ± 0.08 s pre vs 1.851 ± 0.06 s post) (ES = −0.44) (P = <0.05). Small but not statistically significant differences between groups were observed for 10 m and 20 m sprint performance, and no significant differences were observed within or between groups for 505 time. These findings highlight the difficulty in substantially enhancing speed and COD ability in highly trained athletic populations through the addition of a low volume, short duration plyometric training protocol.

In this paper, an analytical investigation of the combined effect of through flow and magnetic field on the convective instability in an electrically conducting fluid layer, bounded in a Hele-Shaw cell is presented within the context of linear stability theory. The Galarkin method is utilized to solve the eigenvalue problem. The outcome of the important parameters on the stability of the system is examined analytically as well as graphically. It is observed that the through flow and magnetic field have both stabilizing effects, while the Hele-Shaw number has destabilizing effect on the stability of system. It is also found that the oscillatory mode of convection possible only when the magnetic Prandtl number takes the values less than unity.

This paper introduces a method for tunnel point cloud and BIM model integration and cross-section monitoring, providing information to analyse tunnel cross-sections and surrounding rock deformation, and support for tunnel maintenance and reconstruction. Three types of data are processed for the integration: laser scanning point cloud, BIM tunnel model and terrain model from oblique photogrammetry. An adaptive BIM modelling scheme is proposed for tunnels with alien structures. Precise spatial registration of the data sets is conducted by applying singular value decomposition (SVD) algorithm to calculate transformation parameters from the point cloud model to the BIM model. Since the tunnel central line has high-order derivability, a cross-section calculation method based on tangent vector is proposed to obtain the cross-sectional profile of tunnels at any mileage. The proposed method has been verified by applying it to a tunnel reconstruction project. The experiment results show that the tunnel point cloud and the BIM model were highly coincident after the integration. The developed program can effectively get the cross-section of the tunnel at any mileage, and correctly express the spatial relationship between the BIM tunnel, the point cloud of tunnel and the external mountainous terrain.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

An atomic-scale approach is employed to simulate the formation of precipitates with different lattice misfits in the early stages of aging of supersaturated aluminum alloys. Simulation results reveal that the increase of lattice misfit could significantly promote the nucleation rate of precipitates, which results in a larger number and smaller size of the precipitates. The morphologies of the precipitates also vary with the degree of lattice misfit. Moreover, the higher the lattice misfit, the earlier the nucleation of the second phase occurs, which can substantially inhibit the movement of dislocations. The research on the lattice misfit of precipitation can provide theoretical guidance for the design of high-strength aluminum alloy.

UAV has become powerful devices for both practitioners and researchers. In recent years, there has been a substantial growth in the usage of UAV for a wide range of applications in research and engineering. UAV are mostly utilized for image capturing techniques due to their time savings, low cost, minimum field work, and high precision. The purpose of this study is to generate an accurate and reliable 3D modelling process using UAVs photogrammetric technology; hence this study allows the techniques to evaluate the practicability of modelling and mapping inaccessible tunnels using images recorded by UAVs and photogrammetry. As a result, the approach was always employed to depict the true state of the place. This research incorporates three experiments. The first experiment is to build a 3D model using only one-directional light source and evaluate the accuracy of 3D photogrammetric model and conducted at the concrete tunnel. The second one is to build a 3D model of underground sewer tunnel using different light sources one-directional and omni-directional. The last experiment was to build 3D model using an UAV system which is developed based on first and second experiment’s result, evaluate an accuracy of 3D photogrammetric model and conducted at the tunnel named in the research as a “pedestrian tunnel. There is certain limitation in this study such as Adding a payload to a drone changed its weight distribution, which affected its stability. If the payload was not properly balanced, it caused the drone to fly unevenly, making it more difficult to control.

The study takes into account different classes of tunnel boring machines (TBMs), with the aim of identifying correlation models which are meant to estimate, at a preliminary design phase, the construction time of a tunnel and to evaluate the mechanical and operational parameters of the TBMs, starting from the knowledge of the tunnel length and/or the excavation diameter. To achieve this goal, first of all a database was created, thanks to the collection of the most meaningful technical parameters from a large number of tunnels; afterward, it was statistically analysed through Microsoft Excel. In a first phase, forecasting models were identified for the three types of machines investigated, separately for compact rocks (open TBM) and fractured rocks (single and double shield TBM). Then, the mechanical parameters collected through the database were analysed, with the aim of obtaining models that take into account, in addition to the type of TBM, the geological aspect, and the type of rock characterising the rock mass. Finally, the validation of the study was proposed in a real case, represented by the Moncenisio base tunnel, a work included in the new Turin–Lyon connection line. The estimated values were compared with the real ones, in order to verify the accuracy of the experimental models identified.

The problem of health status prediction of insulated-gate bipolar transistors (IGBTs) gains a lot of attention in the field of health management of power electronic equipment. The performance degradation of IGBT gate oxide layer is one of the important failure modes. In view of failure mechanism analysis and easy implementation of monitoring circuit, this paper selects the gate leakage current of IGBT as the precursor parameter of gate oxide degradation, and uses time domain characteristic analysis, gray correlation degree, Mahalanobis distance, Kalman filter and other methods to carry out feature selection and fusion, and finally obtains a health indicator characterizing the degradation of IGBT gate oxide. Based on the Convolutional Neural Network and Long Short-Term Memory (CNN-LSTM) network, this paper constructs an IGBT gate oxide degradation prediction model, and performs experimental analysis on the dataset released by NASA-Ames Laboratory, and the average absolute error of performance degradation prediction is as low as 0.0216. Compared with Long Short-Term Memory (LSTM), Convolutional Neural Network (CNN), Support Vector Regression (SVR) and CNN-LSTM models, CNN-LSTM network has the highest prediction accuracy. These results show the feasibility of gate leakage current as a precursor parameter of IGBT gate oxide layer failure, as well as the accuracy and reliability of the CNN-LSTM prediction model.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

The gate resistance is a parasitic element in transistors for RF and millimeter-wave circuits that can negatively impact power gain and noise figure. To develop accurate device models, a reliable measurement methodology is crucial. This article reviews the standard measurement methodology used in the literature and proposes also an additional method, which is evaluated using suitable test structures in a 16nm FinFET process. The advantages and disadvantages of the two approaches are discussed along with their respective application scenarios

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

Pigmented corn is a gramineae food of great biological, cultural and nutritional importance for many Latin American countries, with more than 250 breeds in the American continent. It confers a large number of health benefits due to its diverse and abundant bioactive compounds. In this narrative review we decided to organize the information on the nutrients, bioactive compounds and phytochemicals present in pigmented corn, as well as their effects on human health. Phenolic compounds and anthocyanins are some of the most studied and representative compounds in these grasses, with a wide range of health properties, mainly the reduction of prooxidant molecules. Carotenoids are a group of molecules belonging to the terpenic compounds, present in a large number of pigmented corn breeds, mainly the yellow ones, whose biological activity incorporates a wide spectrum. Bioactive peptides can be found in abundance in corn, having very diverse biological effects that include analgesic, opioid, antihypertensive, etc. activity. Other compounds with biological activity found in pigmented corn are resistant starches, some fatty acids, phytosterols, policosanols, phospholipids, ferulic acid and phlobaphenes, as well as a great variety of vitamins, elements, and fibers. This review aims to disseminate and integrate the existing knowledge on compounds with biological activity in pigmented corn, in order to promote their research, interest and use by scientists, nutrition professionals, physicians, industries and the general population.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

In the pursuit of energy-efficient spiking neural network (SNN) hardware, synaptic devices lev-eraging emerging memory technologies hold significant promise. This study investigates the ap-plication of the recently proposed HfO2/SiO2-based interface dipole modulation (IDM) memory for synaptic spike timing-dependent plasticity (STDP) learning. Firstly, through pulse measure-ments of IDM metal-oxide-semiconductor (MOS) capacitors, we demonstrate that IDM exhibits an inherently nonlinear and near-symmetric response. Secondly, we discuss the drain current re-sponse of a field-effect transistor (FET) incorporating a multi-stack IDM structure, revealing its nonlinear and asymmetric pulse response, and suggest that the degree of the asymmetry depends on the modulation current ratio. Thirdly, to emulate synaptic STDP behavior, we implement dou-ble-pulse-controlled drain current modulation of IDMFET using a simple bipolar rectangular pulse. Additionally, we propose a double-pulse-controlled synaptic depression that is valuable for optimizing STDP-based unsupervised learning. Integrating the pulse response characteristics of IDMFETs into a two-layer SNN system for synaptic weight updates, we assess training and classification performance on handwritten digits. Our results demonstrate that ID-MFET-based synaptic devices can achieve classification accuracy comparable to previously re-ported simulation-based results.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The surface defects of shield subway tunnel can significantly affect the serviceability of the tunnel structure and may compromise the operation safety. To effectively detect the multiple surface defects, this research employs a tunnel inspection trolley (TIT) based on the mobile laser scanning technique. By conducting the inspection of the shield tunnel on a metro line section, various surface defects are identified by the TIT, including water leakage defect, dislocation, spalling, cross-section deformation, etc. To explore the root causes of the surface defects, the association rules between different defects are calculated via an improved Apriori algorithm. Results show that: i) there are significant differences in different association rules of various surface defects of the shield tunnel; ii) the average confidence of the association rule “dislocation &amp; spalling → water leakage” is as high as 57.78%, indicating that most of the water leakage defects are caused by dislocation and spalling of the shield tunnel in the sections being inspected; iii) the weakest rule appears at “water leakage → spalling”, with the average confidence of 13%. The association analysis can be used in predicting the critical defects influencing the structural reliability and operation safety, such as water leakage, and optimizing the construction and maintenance work for the shield subway tunnel.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Voltage-gated potassium (Kv) channels and hyperpolarization-activated cyclic nucleotide-gated (HCN) channels share similar structures but have opposite gating polarity. Kv channels have a strong coupling ( &gt;109) between the voltage sensor (S4) and the activation gate: when S4s are activated the gate is open to &gt;80%, but when S4s are deactivated, the gate is open &lt; 10-9 of the time. Using noise analysis, we show that the coupling between S4 and the gate is &lt; 200 in HCN channels. In addition, using voltage clamp fluorometry, locking the gate open in a Kv channel drastically altered the energetics of S4 movement. In contrast, locking the gate open or decreasing the coupling between S4 and the gate in HCN channels had only minor effects on the energetics of S4 movement, consistent with a weak coupling between S4 and the gate. We propose that this loose coupling is a prerequisite for the reversed voltage gating in HCN channels.

The quality and shelf-life of NCS (Non-centrifugal sugar) mainly depend on the moisture content present in it. NCS formed by the current practice of open sun drying contains moisture substantially greater than the acceptable level of 3%. This paper presents the work taken up to design a tunnel dryer to attain require moisture content in granular NCS for various load conditions. Initially, an experimental investigation had been carried out on a laboratory scale dryer to achieve required moisture content (< 3%) for various load conditions. This experimental data was used for validating two drying models and found that one of the models is best suitable for designing an industrial-scale dryer. For various load conditions on each tray and dryer exit temperature, nine different cases were arrived at. The number of trucks, trays, drying time and energy requirements were computed using the suitable theoretical model. Tunnel dryer with a length of 18 m, a height of 1.2 m, a width of 1 m, number of trucks of 18 and 24 number of trays on each truck was found to be the suitable dryer to dry 1 tone of NCS based on the minimum energy requirement of 176.49 MJ, and a minimum drying time of 68 minutes.

In Uganda, the common bean (Phaseolus vulgaris) is often infested by a complex of insect pests, but the bean stem maggots, aphids, bean leaf beetles, and flower thrips are the most important. Whereas yield losses due to these pests have been established, there is limited information on their population dynamics at different stages of crop growth and their effect on yield and yield components. In order to describe the population dynamics of selected common bean pests at various phases of bean crop growth, and their impact on yield and yield components, a study was carried out in Uganda during 2016 second rains and 2017 first rains in three agro-ecological zones. Bean fly, bean aphids, bean leaf beetles, whitefly, striped bean weevil, leaf hoppers, and caterpillars of Lepidopteran species were the main insects observed. Pesticide spray schedules were imposed to generate different populations of insect pests whose effects on yield and its components were determined. The findings indicate that spray regimes significantly influenced the abundance of bean fly, aphids, whitefly, striped bean weevil, and leaf hoppers but not bean leaf beetles and caterpillars. Additionally, except caterpillars, insect pests were significantly influenced by crop growth stages, but only aphids, whiteflies, bean flies and leaf hoppers exhibited a significant negative relationship with grain yield. Furthermore, yield and yield components varied significantly between spray regimes, agro-ecological zones, and seasons. Our study is important in informing growers on the stage of crop growth at which management tactics such as use of insecticides can be applied for different insect pests.

We present an innovative method harnessing multistability within a diode-pumped erbium-doped fiber laser to construct logic gates. Our approach involves manipulating the intensity of external noise to regulate the probability of transitioning among four concurrent attractors. In this manner, we facilitate the realization of OR, AND, NOT, and NOR logic operations, aligning with the coexisting period-1, period-3, period-4, and period-5 orbits. Employing detrended fluctuation analysis, we establish equilibrium in the probability distributions of these states. The obtained results denote a substantial advancement in the field of optical logic gate development, representing a pivotal stride toward the seamless integration of an all-optical logic gate within laser oscillator-based systems.

The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.

With the progression of AI, embedding advanced AI technologies into small robotics and mobile devices has become essential, driving research towards lightweighting AI models. Our study enhances the EPINET depth estimation model for light field images, aiming for compactness and faster inference while preserving accuracy. We conducted two-step experiments aimed at enhancing inference efficiency: Initially, by adjusting input streams and convolution layers, we simplified the CNN model, achieving faster inference times at the cost of reduced accuracy. To address this reduction in accuracy, we then applied knowledge distillation, allowing the simplified model to learn from the original model’s more complex patterns. In our quantitative experiments using two error metrics, MSE (Mean Squared Error) and BadPix, we identified optimal knowledge positions and evaluated the required complexity for the student model. As a result, our method improved MSE by 21% and BadPix by 14% compared to training without it. Furthermore, the student model achieved an inference speed 13% faster than the teacher model and surpassed its accuracy by 10% in MSE. Additionally, we demonstrated that repeatedly applying our approach could further enhance both model compactness and accuracy.