During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

Recognition of the human interaction on the unconstrained videos taken from cameras and remote sensing platforms like a drone is a challenging problem. This study presents a method to resolve issues of motion blur, poor quality of videos, occlusions, the difference in body structure or size, and high computation or memory requirement. This study contributes to the improvement of recognition of human interaction during disasters such as an earthquake and flood utilizing drone videos for rescue and emergency management. We used Support Vector Machine (SVM) to classify the high-level and stationary features obtained from Convolutional Neural Network (CNN) in key-frames from videos. We extracted conceptual features by employing CNN to recognize objects from first and last images from a video. The proposed method demonstrated the context of a scene, which is significant in determining the behaviour of human in the videos. In this method, we do not require person detection, tracking, and many instances of images. The proposed method was tested for the University of Central Florida (UCF Sports Action), Olympic Sports videos. These videos were taken from the ground platform. Besides, camera drone video was captured from Southwest Jiaotong University (SWJTU) Sports Centre and incorporated to test the developed method in this study. This study accomplished an acceptable performance with an accuracy of 90.42%, which has indicated improvement of more than 4.92% as compared to the existing methods.

The extensive use of polypropylene (PP) in various industries has heightened interest in devel-oping efficient methods for recycling and optimising its mixtures. This study focuses on formu-lating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The in-vestigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, at-taining R² values over 0.99. Symbolic regression further enhanced these models, offering signif-icant improvements. To mitigate overfitting, empirical noise and variable swapping were in-troduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the de-velopment of recycling technologies and sustainable practices in the polymer industry by opti-mising processing and enhancing the use of recycled materials.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

Traditional terrain analysis has relied on Digital Topographic Maps produced by national agencies and Digital Elevation Model (DEM) created using Airborne LiDAR. However, these methods have significant drawbacks, including the difficulty in acquiring data at the desired time and precision, as well as high costs. Recently, advancements and miniaturization in LiDAR technology have enabled its integration with Unmanned Aerial Vehicle (UAV), allowing for the collection of highly precise terrain data. This approach combines the advantages of conventional UAV photogrammetry with the flexibility of obtaining data at specific times and locations, facilitating a wider range of studies. Despite these advancements, the application of UAV LiDAR in terrain analysis remains underexplored. This study aims to assess the utility of UAV LiDAR for terrain analysis by focusing on the doline features within karst landscapes. In this study, we analyzed doline terrain using three types of data: 1:5000 scale digital topographic maps provided by the National Geographic Information Institute (NGII) of Korea, Digital Surface Models (DSM) obtained through UAV photogrammetry, and DEM) acquired via UAV LiDAR surveys. The analysis results indicated that UAV LiDAR provided the most precise three-dimensional spatial information for the entire study site, yielding the most detailed analysis outcomes. These findings suggest that UAV LiDAR can be utilized to represent terrain features with greater precision in the future which is expected to be highly useful not only for generating contours but also for conducting more detailed topographic analyses, such as calculating area and slope of the study sites.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

Salt stress is one of the major abiotic stresses that lead to crop yield reduction worldwide. Melatonin (MT), an endogenous hormone synthesized in plants, plays an important role in responding to abiotic stimuli such as drought, salinity, heat, cold, etc. However, the molecular mechanisms of MT-mediated abiotic stresses remain to be better understood. In order to explore the key genes and pathways of melatonin in alleviating salt stress, physiological and biochemical indicators as well as transcriptomics profile were conducted in alfalfa seedlings. The results showed that the germination rate, bud length and fresh weight of alfalfa seedlings added with melatonin were higher than those treated with salt alone. In addition, Malondialdehyde (MDA) and Superoxide anion (O2-) contents also displayed a decreasing trend. The activity and content of Superoxide dismutase (SOD)、peroxidase (POD) and Glutathione (GSH) increased to varying degrees. In order to further reveal the molecular mechanism of MT-mediated salt tolerance of alfalfa, transcriptome analysis was performed on alfalfa seedlings. 2,181 differentially expressed genes (DEGs) were obtained in the salt-treated group, including 780 upregulated genes and 1,401 down-regulated genes, while 4,422 DEGs were obtained in the MT group, among which 1,438 were upregulated and 2,984 were downregulated. By using GO functional annotation and KEGG pathway enrichment, we found that DEGs were mainly enriched in the biosynthesis of flavonoids, isoflavones, plant hormones, Glutathione (GSH), soluble sugars and other substances, as well as in the ABC transporter and MAPK signaling pathways. Among them, the DEGs in the MT group was more enriched in these pathways, suggesting that MT can combat salt stress by regulating the expression of genes related to phytohormone and antioxidant capacity, which has important reference value for the breeding of salt-tolerant alfalfa and other crops.

Advanced image processing will be crucial for emerging technologies such as autonomous driving, where the requirement to quickly recognize and classify objects under rapidly changing, poor visibility environments in real time will be needed. Photonic technologies will be key for next-generation signal and information processing, due to their wide bandwidths of 10’s of Terahertz and versatility. Here, we demonstrate broadband real time analog image and video processing with an ultrahigh bandwidth photonic processor that is highly versatile and reconfigurable. It is capable of massively parallel processing over 10,000 video signals simultaneously in real time, performing key functions needed for object recognition, such as edge enhancement and detection. Our system, based on a soliton crystal Kerr optical micro-comb with a 49GHz spacing with >90 wavelengths in the C-band, is highly versatile, performing different functions without changing the physical hardware. These results highlight the potential for photonic processing based on Kerr microcombs for chip-scale fully programmable high-speed real time video processing for next generation technologies.

Citrus species essential oils (EOs) are significant sources of bioactive compounds and demonstrate diverse therapeutic effects. However, limited documentation exists regarding the phytochemicals associated with their biological activities. This study aims to assess the antioxidant activity, plant inhibitory properties, and brine shrimp cytotoxic effects of EOs derived from three Citrus species: C. sinensis, C. limon, and C. hystrix. Utilizing chemometric analysis and gas chromatography-mass spectrometry (GC-MS) fingerprints, the volatile components contributing to antioxidant activity were elucidated. The peels of the Citrus samples were hydro-distillated to obtain EOs, and subsequently subjected to antioxidant, plant inhibitory, and brine shrimp cytotoxic assays. The results indicated that C. limon EO exhibited the highest antioxidant activity, while C. hystrix and C. sinensis EOs demonstrated pronounced inhibitory effects against Aetrmia salina and Lactuca sativa, respectively. GC-MS analysis facilitated the identification of key compounds in each EO. Principal component analysis (PCA) and hierarchy cluster analysis (HCA) effectively categorized Citrus EOs based on their antioxidant properties, highlighting the proximity of C. limon and C. sinensis. Among the identified compounds, D-limonene, α-Terpineol, Caryophyllene, (+)-3-Carene, β-Pinene, (-)-Spathulenol, trans-p-Mentha-1(7),8-dien-2-ol, and trans-Verbenol were the most discriminating compounds affected the antioxidant activity of C.limon and C. sinensis EOs.

In this study, we successfully synthesized a novel branched polyamide 6 with ε-caprolactam(CPL) and α-Amino-ε-caprolactam(ACL) through hydrolytic ring-open co-polymerization. The NMR characterization and rheological test result proved the existence of branched chain structure additionally. The branched chain structure caused a remarkable enhancement in the rheological properties. The met index(MFR),zero shear rate viscosity and storage modulus at low frequency region had a remarkable increase.The shear thinning phenomenon became more obvious. The thermal properties test determined by differential scanning calorimetry(DSC) showed that the melting point and crystallinity of co-polymers decreased with the increase of ACL addition.However, the crystal structure of the samples remained unchanged. The appropriate addition amount of ACL can improve the tensile mechanical properties of the co-polymers. When the amount of ACL was 1%, the tensile strength and fracture elongation rate of the co-polymers had the most significant increase.

The Covid-19 pandemic spreads in waves for a year and a half, despite significant worldwide efforts, the development of biochemical diagnostic methods and population vaccination. One of the reasons for the infection spread is the impossibility of early disease detection through biochemical diagnostics, since biochemical processes slowly develop in a body. At the same time, well known that behavioral characteristics of a person, measured based on reflex movements, are capable for inertialess assessment of psychophysiological parameters. Vibraimage technology is the method of head micromovements video processing by inter-frame difference accumulation and converting spatial and temporal characteristics of the inter-frame difference into behavioral and psychophysiological parameters. Here we shown that behavioral parameters measured by vibraimage changed during COVID-19 infection. The identification of changes signs in behavioral parameters detected by AI trained on patients and controls. The best diagnostic accuracy (higher 94%) obtained using instantaneous values of behavioral parameters measured with the following vibraimage settings: 10Hz frequency of basic measurements; 25 inter-frame difference accumulations and averaging the diagnostic results over period of at least 5 seconds. COVID-19 diagnoses by behavioral parameters showed earlier (5-7 days) detection of the disease compared to symptoms and positive results of biochemical RT-PCR testing. Proposed method for COVID-19 diagnosis indicates infected persons within 5 seconds video processing using standard television cameras (web, IP) and computers, allows mass testing/selftesting and will stop the pandemic spread. We assume that head micromovements analysis for diagnosis of various diseases is possible not only with the help of vibraimage technology. Further research of human head micromovement analysis will help stop the COVID-19 pandemic and will contribute to the development of new contactless and environmentally friendly methods for early diagnosis of diseases.

The success of deep learning (DL) in offline brain-computer interfaces (BCIs) has not yet translated into efficient online applications. This is due to two limiting factors: the need for large amounts of training data in DL and the fact that current DL solutions are primarily developed for offline decoding. To enable real-time decoding, even across subjects without calibration data, we first introduce a novel method real-time adaptive pooling (RAP) to tune existing offline DL models towards online decoding by modifying the pooling layers. To reduce the amount of training data required, our approach leverages different levels of domain adaptation. We show how different settings enable different adaptation solutions. Our results demonstrate that our approach is both powerful and can be calibration-free, providing a robust and practical solution for real-time BCI applications. These findings pave the way for the development of co-adaptive and highly efficient DL-based BCI systems.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

The extensive utilization of drones has led to numerous scenarios that encompass both advantageous and perilous outcomes. By using deep learning techniques, it is aimed to reduce the dangerous effects of drone use through early detection of drones.The state of the art of the study is evaluation of deep learning approaches such as pre trained YOLOv8 drone detection for security issues. In this study, dataset collected by Mehdi Özel for a UAV competition are sourced from GitHub. These images are labeled using Roboflow, and the model is trained on Google Colab. To enhance model performance, dataset augmentation techniques including rotation and blurring are implemented. Following these steps, a significant precision value of 0.946, a notable recall value of 0.9605 and a considerable precision-recall curve value of 0.978 are achieved, surpassing many popular models such as Mask CNN, CNN, and YOLOv5.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

This paper presents and demonstrates the development of a new lightweight coating for aluminium alloy using a novel multicomponent alloy based on the AlSiMgCu system. This coating was applied using a newly designed approach that combined High-Velocity Oxy-Fuel (HVOF) and Plasma Spraying processes. This hybrid technique enables the deposition of coatings with enhanced performance characteristics. The microstructure was studied using optical microscopy (OM) and scanning electron with energy dispersive X-ray spectroscopy (SEM+EDS) microscopy, revealing good adhesion and compaction between the multicomponent coating and the A6061 substrate with 50 to 150 µm thickness. Vickers indentations were performed on the substrate and the new coating material, revealing a 50% improvement in the material's hardness compared to the casted alloy. Additionally, electrical conductivity measurements showed approximative x3.3 times values compared to the alloy in as-cast condition due to high solidification rates altering the morphology of the phases. Corrosion tests demonstrated a lower corrosion rate compared to other multicomponent aluminium alloys and similar to thermal treated A6061 alloy. Finally, tribological results obtained using ball on disc (BOD) test and laser scanning confocal microscopy, confirmed that the new multicomponent coating exhibited reductions in both friction coefficient and wear rate by more than 20% and 50%, respectively. This study demonstrates that using multi-component aluminium coatings could lead to developing of new automotive parts with enhanced properties for corrosion resistance, electrical conductivity, and wear conditions. Optimizing the thermal spraying parameters could further enhance the coating, achieving greater and more homogeneous thicknesses and yielding even higher performance properties.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as Smart Dust. Several efforts focused primarily on computing and networking capabilities but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data was processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.

This paper introduces a quantitative methodology for assessing drone pilot performance, aiming to reduce drone-related incidents by understanding the human factors influencing performance. The challenge lies in balancing evaluations in operationally relevant environments with those in a standardized test environment for statistical relevance. The proposed methodology employs a novel virtual test environment that records not only basic flight metrics but also complex mission performance metrics, such as the video quality from a target. A group of Belgian Defence drone pilots were trained using this simulator system, yielding several practical results. These include a human performance model linking human factors to pilot performance, an AI co-pilot providing real-time flight performance guidance, a tool for generating optimal flight trajectories, a mission planning tool for ideal pilot assignment, and a method for iterative training improvement based on quantitative input. The training results with real pilots demonstrate the methodology’s effectiveness in evaluating pilot performance for complex military missions, suggesting its potential as a valuable addition to new pilot training programs.

Convolutional Neural Networks (CNNs) present drawbacks for modeling geometric transformations, such as scaling and rotation, caused by the convolution operation’s locality. Deformable convolution (DCON), a mechanism that substitutes standard convolution, increasing the receptive field to capture relevant features, is a promising approach to solve this drawback and improve the robustness of CNNs. However, the optimal way to replace the standard convolution with its deformable counterpart in a CNN model is unclear. In this study, we clarify this aseveration by conducting several experiments using deformable convolutions applied in the layers that conform a small four-layer CNN model. We also use deformable convolutions on the four-layers of several ResNet CNNs with depths 18, 34, 50, and 101. The models were tested in binary balanced classes with 2D data for image classification: Cats & Dogs, EyesPACS, Spyders & Chickens, and Shapes. After this testing, we evaluated DCON in 3D data for action recognition: UCF101 and Human2 (a dataset we compiled to control movement, clothing and background). The contribution of this research lies in a guideline to use DCON. It can be summarized as follows: if DCON is used on the first layers of the proposal of model (with simple features), the computational resources expressed as the quantity of Flops will tend to increase and produce bigger misclassification than the standard CNN. However, if the DCON is used at the end layers, the quantity of Flops used in the training and testing will decrease, and the classification accuracy will improve by up to 20% about the base model. Moreover, it gains robustness when using deformable convolutions because it can adapt to the region of interest. Also, the best kernel size of the DCON is three. It showed better results than size five. In the last case, the quantity of Flops increase quadratically, but their performance does not increase significantly. With these results, we propose a guideline to use the DCON and contribute to understanding the impact of DCON on the robustness of CNNs.

A convenient and efficient strategy for the preparation of 2-sulfonylindoles has been achieved through iodophor/H2O2-mediated 2-sulfonylation of indoles with readily available sulfonyl hydrazides in aqueous phase. Iodophor is commercially available and serves as the green catalyst and aqueous phase. A series of 2-sulfonylated products from indoles and N-methylpyrrole were synthesized in moderate yields in only 10 min. Control experiments were also conducted to reveal the mechanism. This method is environment friendly, easy to operate and suitable for a wide range of substrates.

The efficient preparation of single-stranded DNA (ssDNA) rings, as a macromolecular construction approach with topological features, has aroused much interest due to their numerous applications in biotechnology and DNA nanotechnology. However, an extra splint is essential for enzymatic circularization, and by-products of multimers are usually present at high concentrations. Here, we proposed a simple and robust strategy of using permuted precursor (linear ssDNA) for circularization by forming an intramolecular dynamic nick using a part of the linear ssDNA substrate itself as the template. After the simulation of the secondary structure for desired circular ssDNA, the linear ssDNA substrate is designed to have its ends on the duplex part (≥5 bp). By using this permuted substrate with 5'-phosphate, the splint-free circularization is simply carried out by T4 DNA ligase. Very interestingly, formation of only several base pairs (2–4) flanking the nick is enough for ligation, although they form only instantaneously under ligation conditions. More significantly, the 5 bp intramolecular duplex part commonly exists in genomes or functional DNA, demonstrating the high generality of our approach. Our findings are helpful for understanding the mechanism of enzymatic DNA ligation from the viewpoint of substrate binding.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

Green manure could improve soil nutrients and crop production, playing a significant role in sustainable agriculture. However, the impacts of green manure on crop health and the roles soil microbial communities play in the process haven’t been clarified clearly yet. In this study, we investigated soil microbial community composition and structure in four tobacco farmlands, which were treated with different green manure (control, ryegrass, pea and rape), using 16S rRNA gene amplicons sequencing. Results showed that green manure had significant impacts on soil properties, microbial communities and tobacco health. First, soil total C, N and Ca content increased significantly in groups treated with green manure than control. Second, soil community diversity was significantly higher in groups treated with green manure. Third, green manure especially ryegrass, decreased tobacco disease (bacterial wilt) rate dramatically, and the process might be mediated by soil microbial communities. On the one hand, several microbial populations were found to be potentially disease inducible or suppressive. For example, the abundances of Dokdonella and Rhodanobacter were positively correlated to tobacco disease rate, while Acidobacteira_Gp4 and Gp6 had negative correlations with tobacco disease. On the other hand, soil microbial communities were shaped by soil properties (e.g., pH, C and N content). In conclusion, our research showed that green manure could increase soil nutrients directly, and further improve tobacco health mediated by soil microorganisms, which may shed light on revealing interactions among soil properties, microorganisms and plants.

Wildlife monitoring can be time-consuming and expensive, but the fast-developing technologies of uncrewed aerial vehicles, sensors, and machine learning pave the way for automated monitoring. In this study we trained YOLOv5 neural networks to detect Points of Interest, hare (Lepus europaeus), and roe deer (Capreolus capreolus) in thermal aerial footage and proposed a method to manually assess the parameter mean average precision (mAP), compared to the number of actual false positive and false negative detections in a subsample. This showed that a mAP close to 1 for a trained model does not necessarily mean perfect detection and provided a method to gain insights into the parameters affecting the trained models' precision. Furthermore, we provided a basic, conceptual algorithm for implementing real-time object detection in uncrewed aircraft systems equipped with thermal sensors, with high zoom capabilities, and a laser rangefinder. Real-time object detection is becoming an invaluable complementary tool for the monitoring of cryptic and nocturnal animals with the use of thermal sensors.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

In the design of real-world networks, researchers evaluate various structural parameters to assess vulnerability, including connectivity, toughness, and tenacity. Recently, the tightness metric has emerged as a potentially superior vulnerability measure, although many related theorems remain unknown due to its novelty. Harary graphs, known for their maximum connectivity, are an important class of graph models for network design. Prior work has evaluated the vulnerability of three types of Harary graphs using different parameters, but the tightness metric has not been thoroughly explored. This article aims to calculate the tightness values for all three types of Harary graphs. First, it will attempt to calculate the lower bound for the value of the tightness parameter in Harary graphs using existing lemmas and theorems. Then, by presenting new lemmas and theorems, we will try to find the exact value or upper bound for this parameter in Harary graphs. For the first type of Harary graph, the tightness is precisely determined, while for the second and third types, upper bounds are provided due to structural complexity. The lemmas, theorems, and proof methods presented in this research may be used to calculate other graph and network parameters. However, the newness of the tightness parameter means that further research is needed to fully characterize its properties.

In recent years, the scientific and technological developments led to an explosion of available videos on the web, increasing the necessity of fast and effective video analysis and summarization. Video summarization methods aim to generate a synopsis by selecting the most informative parts of the video content. The user’s personal preferences, often involved in the expected results, should be taken into account in the video summaries. In this paper, we provide the first comprehensive survey on personalized video summarization relevant to the techniques and datasets used. In this context, we classify and review personalized video summary techniques based on the type of personalized summary, on criteria, on the video domain, on the source of information, on the time of summarization, and on the machine learning technique. Depending on the type of methodology used by the personalized video summarization techniques for the summary production process, we classify the techniques into five major categories, which are feature-based video summarization, key frame selection, shot selection-based approach, video summarization using trajectory analysis, and personalized video summarization using clustering. We also compare personalized video summarization methods and present 37 datasets used to evaluate personalized video summarization methods. Finally, we analyze opportunities and challenges in the field and suggest innovative research lines.

Unmanned aerial vehicle (UAV), or drone is recognized for its potential to improve efficiency and address last-mile delivery issues. As a result, there has been a lot of activity in recent years in the field of drone scheduling and routing. Unlike the vehicle routing problem, drone route design is difficult due to several operational characteristics, such as speed optimization, multitrip operation, and energy consumption estimation. On the one hand, drone energy consumption is a complex nonlinear function of both speed and payload in practice. On the other hand, the high operating speed of drones can significantly curtail the drone range, thereby limiting the efficiency of drone delivery systems. Most of the existing drone delivery models either assume constant drone speed or do not consider the effect of drone speed and parcel weight on energy consumption, leading to costly or energy-infeasible routes. This paper addresses the trade-off between speed and flight range in a multi-trip drone routing problem with variable flight speeds (DRP-VFS), in which a team of homogeneous drones is employed for delivery services. We propose a new model to particularly consider energy constraints using a nonlinear energy consumption model and treat drone speeds as decision variables so that various drone speeds can be adopted in applications. The DRP-VFS is initially formulated as mixed-integer linear programming (MILP) to minimize total energy consumption. To solve large-scale instances, we propose a three-phase adaptive large neighborhood search (ALNS) algorithm. The experimental results demonstrate that suboptimal solutions can be found effectively in practical scenarios using the proposed method. Furthermore, results indicate that operating drones at variable speeds leads to about 21% of energy savings compared to fixed speeds, boasting advantages in cost-savings and range extensions.

Vibrio parahaemolyticus is an important foodborne bacterium that causes severe gastroenteritis following the consumption of contaminated seafood. To identify V. parahaemolyticus and determine its pathogenicity, the U.S. Food and Drug Administration (FDA)’s Bacteriological Analytical Manual (BAM) recommends a multiplex polymerase chain reaction (PCR) protocol to simultaneously detect the species-specific thermolabile hemolysin (tlh) gene and the pathogenic thermostable-related hemolysin (trh) and thermostable-direct hemolysin (tdh) genes. However, this assay has shown two limitations: difficulty in separating the amplicons of the trh (486 bp) and tlh (450 bp) genes due to their similar sizes, and the weaker band exhibited by the tdh gene amplicon (270 bp). The present study aimed to improve the BAM’s multiplex PCR assay by separating the three amplicons with similar intensity. A new primer set was applied for the tlh gene (369 bp) alongside the existing primers for the trh and tdh genes. The amplicons for the three genes were effectively separated by electrophoresis on a 2% tris-borate-EDTA (TBE) agarose gel within 45 minutes. Primer concentrations of 0.2 µM for trh, 0.2 µM for tlh, and 0.4 µM for tdh produced a significant amount of amplicons among various combinations of primer concentrations with 35 PCR cycles (P < 0.05). This assay exhibited a detection limit of 10 pg of bacterial DNA, demonstrating its high sensitivity. It did not display amplicons from nine Vibrio strains known to be human pathogens or from 18 well-documented foodborne pathogens. Therefore, the present multiplex PCR protocol could help overcome the limitations of existing assays and provide a more reliable method for detecting the three genes of V. parahaemolyticus.

Depth-sensing technology has led to broad applications of inexpensive depth cameras that can capture human motion and scenes in 3D space. Background subtraction algorithms can be improved by fusing color and depth cues, thereby allowing many issues encountered in classical color segmentation to be solved. In this paper, we propose a new fusion method that combines depth and color information for foreground segmentation based on an advanced color-based algorithm. First, a background model and a depth model are developed. Then, based on these models, we propose a new updating strategy that can eliminate ghosting and black shadows almost completely. Extensive experiments have been performed to compare the proposed algorithm with other, conventional RGB-D algorithms. The experimental results suggest that our method extracts foregrounds with higher effectiveness and efficiency.

Polymeric Intraocular lenses (IOLs) are vital for restoring vision following cataract surgery and for correcting refractive errors. Despite technological and medical advancements, challenges persist in achieving optimal vision and preventing complications. Surface modifications aim to mitigate the risk of posterior capsule opacification (PCO), while pre-operative measurements aid in selecting suitable IOLs. However, individualized solutions are lacking and there is a clear demand for the development of fully customised IOL surfaces. We employ laser micromachining technology for precise modifications via ablation on PMMA and Acrylic IOLs, using femtosecond (fs), nanosecond (ns), and diode continuous wave (CW) lasers, at wavelengths ranging from near-ultraviolet to infrared. Characterization reveals controlled ablation patterning, achieving feature sizes from as small as 400 nm to several micrometers. Regular and confocal Micro-Raman spectroscopy revealed alterations of the IOL materials' structural integrity for some pattering cases, thus affecting the optical properties, while these can be minimised by proper selection of micromachining conditions. The results suggest the feasibility of accurate IOL patterning, which could offer personalized vision correction solutions, based on relevant corneal wavefront data, thus surpassing standard lenses, marking a significant advancement in cataract surgery outcomes.

Detecting cracks in structural health monitoring is crucial for ensuring infrastructure safety and longevity. Using drones to obtain crack images and automate processing can improve the efficiency of crack detection. To address the challenges posed by the limited computing resources of edge devices in practical applications, we propose CrackScopeNet, a lightweight segmentation network model that simultaneously considers local and global crack features, suitable for deployment on drone platforms with limited computational power and memory. CrackScopeNet features a multi-scale branch to improve sensitivity to cracks of varying sizes without substantial computational overhead and a stripe-wise context attention mechanism to enhance the capture of long-range contextual information, mitigating the interference from complex backgrounds. Experimental results on CrackSeg9k dataset demonstrate that CrackScopeNet leads to a significant improvement in prediction performance, with the highest mean intersection over union (mIoU) scores reaching 82.12%, while maintaining a lightweight architecture with only 1.05M parameters and 1.58G floating point operations (FLOPs). Besides, CrackScopeNet excels in inference speed on edge devices without GPU because of its low FLOPs. CrackScopeNet contributes to the development of efficient and effective crack segmentation networks, suitable for practical structural health monitoring applications using drone platforms.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

Hyperspectral imaging data holds great potential for various stages of the mining life cycle in active and abandoned mines. The technology, however, has yet to achieve large-scale industrial implementation and acceptance. While hyperspectral satellite im-agery yields high spectral resolution, high signal-to-noise ratio (SNR), and global availability with breakthrough satellite sys-tems like EnMAP, EMIT, and PRISMA, limited spatial resolution poses challenges for mining sectors, which require decimeter- to centimeter-scale spatial resolution for applications such as reconciliation, ore/waste estimates, geotechnical assessments, and en-vironmental monitoring. Hyperspectral imaging from drones (Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the pit/ mine scale, with the capability for frequent, user-defined re-visit times. Collecting data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions offers to detect different minerals and surface alteration patterns, potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we review of applicable instrumentation, software components, and relevant studies deploying hyperspectral imaging in or appropriate to the mining sector, especially for hyperspectral VNIR-SWIR UASs. If directly applicable, draw on previous insights derived from airborne, satellite, and ground-based imaging systems. We also discuss common practices for UAS survey planning and sampling considerations for interpretation.

The Sustainable Development Center of the University of Brasilia is one of the modernist buildings that make up the Darcy Ribeiro campus. The architectural project contains several recommendations for the execution of the flat roof waterproofing system, as well as details for rainwater runoff and drainage, which reveals a certain concern with watertightness. The research seeks to identify the relationship between the pathological manifestations recognized on the roof and the semicircular shape of the building, assessing the state of conservation through the use of damage maps as an analysis tool. The article is based on a field survey using aerophotogrammetry with a drone, the application of vector drawing software for graphic representation and discussion of the possible causes, agents and mechanisms of degradation at work. The results show the importance of mechanical protection for the good performance of the waterproofing system, as well as the need for correct sizing of expansion joints in order to absorb and relieve the stresses caused by hygrothermal variations. The methodology incorporated proved to be effective and economical in diagnosing and monitoring pathological manifestations, making it possible to plan maintenance actions that extend the useful life and preserve the intrinsic characteristics of building systems.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

Background: The laryngeal mask airway Vision Mask (LMA VM) is a supraglottic airway device (SAD) with vision guidance system. The ideal head and neck position for direct laryngoscopy is known, but the ideal position for placing a LMA is not. The objective of this study is to evaluate and compare the optimal position for placement of a video laryngeal mask airway. Methods: This was a prospective observational, transversal and analytical study of 72 consecutive patients. In the same patient, laryngeal vision was first assessed with the head and neck in the sniffing position and then with the head in the neutral position. Procedures were filmed and performed by the same investigator. Assessment of the laryngeal view was performed using two classifications: modified Cormack-Lehane classification and Brimacombe classification. Device placement was considered adequate when the Cormack-Lehane rating was scored from 1 to 2 and the Brimacombe rating was from 2 to 4. Results: 72 patients were included in this study. In the assessment of the glottis using the Cormack Lehane classification for fiberoptic view, laryngeal visibility was adequate in 64 (88.89%) patients in the neutral position and in 65 (90,28%) patients in the sniffing position (p>0,05). In the fiberoptic view of the glottis, assessed using the Brimacombe classification, laryngeal visibility was adequate in 68 (93%) patients in the neutral position and in 69 (95%) patients in the sniffing position, (p>0,05). There was no statistically significant difference in the rate of success between the sniffing position (70 patients, 97.22% success rate) and the neutral position (67 patients, 93.06% success rate) during the first insertion attempt. Two patients required a second attempt in the sniffing position, while five patients required a second attempt in the neutral position. Conclusion: An adequate sniffing position did not result in a better glottic view than neutral position, and the number and type of additional maneuvers were equal in both positions.

The human eye is a vital source of collecting information worldwide via daily observation. The computer science area recognizes it in research as a human-computer interaction. Human blink is an integral part of this observation as a research topic. Several studies have been conducted on eye blinking and left-right eye movements. Previous studies conducted on the eye blink consider the availability of hardware devices high in the budget, high Precision, and low light expo-sure, unlike our study, which uses low-budget devices as simple as a webcam and more versatile usable techniques, incredibly both dim and high light to name a few. This study offers the observational approach via ResNet101v2, VGG-19, and Convolution Neural Network (CNN) architectures. Outperforming both VGG-19 and CNN in this study, ResNet101v2 achieves an impressive accuracy of 98.2%. In contemporary times, deep learning in AI is taking an advanced form. This study attempts to provide a new insight into the real-world implementation of the eye blink.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

This paper presents a simple drone survey and image processing approach to identifying St. John's wort (Hypericum perforatum) on grazing land in the Hunter Valley NSW, Australia. St John’s wort is an invasive species (weed) that competes with pasture, poisons livestock, can downgrade wool with ‘vegetable fault’, and decreases property values. Identifying the locations of St John wort from the ground can be difficult due to topography, limited access, and/or larger land areas of mixed vegetation. In this study, a drone was used to survey a 174-ha grazing property in the Hunter Valley NSW (Australia). The images were stitched together using commercially available software. A unique Visual Atmospheric Resistance Index (VARI) attribute was identified and used to highlight the presence of St John’s wort in the survey area. These sub-areas were then digitised onto high resolution maps for future planning use by land managers.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

This research study focuses on addressing practical optimization challenges in audio-visual content using advanced computational intelligence methods, with a specific emphasis on privacy-preserving issues. The research will be presented as a proposal and can be conducted based on the provided ideas. Computational intelligence encompasses various approaches, including evolutionary algorithms, learning methods, fuzzy systems, and neural networks, which have become essential tools for tackling complex engineering optimization problems due to computational expenses, dimensional complexities, and interdisciplinary integration. The research objectives include a thorough investigation of optimization challenges in audio-visual content, the delineation of problem characteristics, and the development of relevant methodologies based on these specifications. The main goals of the study, titled "Advanced Computational Intelligence Assisted Less-Expensive Privacy-Preserving Optimization," encompass the development of a metamodel-based learning algorithm integrated with evolutionary computation for privacy-preserving optimization, less-expensive signal watermarking optimization using hybrid metamodeling and evolutionary algorithms, and a closed-loop robust intelligent PID control system applied in real-time dynamic signal watermarking. Additional objectives may be defined as the research progresses and further background review is conducted.

This study evaluates the use of remote sensing to improve real-time adaptive management of grasslands. By quantifying grassland biomass through changes in sward height from pre- and post-grazing events using unmanned aerial systems (UAS), we derived accurate biomass estimates. Additionally, we aimed to enhance the biomass estimation with spectral data from Sentinel-2 imagery, which is often hindered by cloud contamination, by combining it with a random forest algorithm. The calibration of UAS biomass using field measurements from sward height changes through 3D photogrammetry produced strong regression metrics (R2= 0.75, RMSE= 1240 kg DM/ha and MAE=980 kg DM/ha). Integrating this UAS-derived data with Sentinel-2 imagery, the satellite based biomass model (R2= 0.56, RMSE=2140 kg DM/ha and MAE=1585 kg DM/ha) compared to using the Sentinel-2 random forest-enabled model alone (R2= 0.56, RMSE=2140 kg DM/ha and MAE=1585 kg DM/ha). This study emphasise the importance of timely and accurate biomass estimation for adaptive gazing management at the field level, highlighting the balance between utilising advanced remote sensing technologies and addressing operational complexities. By optimising the integration of UAS and satellite data, we aim to enhance grassland utilisation, ecosystem functions, nutrient cycling, and sustainability in land use.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

Effective agricultural management in maize production operations starts with the early quantification of seedlings. Accurately determining plant presence allows growers to optimize planting density, allocate resources, and detect potential growth issues early on. This study presents an in-depth analysis of multiple object detection models used by drones to count maize seedlings, while concurrently investigating the influence of planting density, flight altitude, and plant growth stage. The findings of this study demonstrate that one-stage models are able to more accurately detect maize seedlings than two-stage models. In particular, YOLOv8n exhibits outstanding performance, achieving an F1-score of over 0.92 under various density conditions and maintaining a stable performance, especially under densities below 105,000 plants/ha. Additionally, planting density and growth stage were observed to significantly affect detection accuracy, with performance declining as density and growth stage increased. Image resolution and detection were impacted by flight altitude, with lower flights producing higher-quality results. Ultimately, YOLOv8n displays optimal performance under various conditions, providing crucial data to support intelligent decision-making. This research offers valuable insights into the application of object detection technology and provides a basis for the future development of precision agriculture.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

In this work, we explore the ability to dynamically group the Wind Turbine (WT) of a Wind Farm (WF) based on the behaviour of some of their Supervisory Control And Data Acquisition (SCADA) signals to detect the turbines that exhibit abnormal behaviour. We centre this study on a small WF of five WTs. We use the fact that the same signals from different turbines in the same WF coherently evolve temporally in a time domain, describing very similar waveforms. In this contribution, we use averaged signals from the SCADA system and omit maximums, minimums and standard deviations, focusing mainly on velocities and other slowly varying signals. For the temporal analysis, sliding windows of different temporal durations and overlapings are explored. The capability to automatically identify WTs whose signals differ from the group’s behaviour can alert and program preventive maintenance operations on such WTs before a major breakdown occurs.

This paper presents an approach to teacher identity heritage as result of the implementation of a research device created through Arts-based Research (ABR) methods, specifically with video elicitation and video essay used as research tools. Two main objectives were raised. The first one, to establish the real relevance of focusing performance on teacher identity. The second one, testing a new methodological proposal specifically designed for this purpose, but still useful in other contexts where heritage identity is as present as in teaching. The device, Body-camera, involves a process that allows new ways to understand the creation of identities using video to encourage the production of new meanings by visual and oral data. The participants were teachers in training during their internship period. Some notions about teachers' identity heritage were revealed, and also preserved, firstly, through personal perspectives by video elicitations and secondly, through collective perspectives by video essays. Both are video structures used in ABR which mix creative experience, memories, life experiences, relationships and links that shape the teachers’ professional identity.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

Short video addiction refers to a psychological dependency on short video applications, characterized by an intense attachment and an inability to control usage, leading to typical addiction symptoms. While its definition bears similarities to substance addiction, significant differences also exist. According to the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5), published in 2013, short video addiction has not yet been officially classified as an addiction disorder. To facilitate more in-depth and standardized research on short video addiction, it is essential to synthesize and organize existing studies on its theoretical foundations and mechanisms.

Recently, various research has been developed addressing communication sensors for Unmanned Aerial Systems (UASs); especially when pondering control difficulties, communication is a crucial component. To this end, strengthening a control algorithm with redundant linking sensors ensures the overall system works accurately even if some components fail. This paper proposes a novel approach to integrate several sensors and actuators for a heavy Unmanned Aerial Vehicle (UAV). Additionally, a cutting-edge Robust Thrust Vectoring Control (RTVC) technique is designed to control various communicative modules during a flying mission and converge the attitude system to stability. The results of the study demonstrate that even though RTVC is not frequently utilized, it works as well as cascade PID controllers, particularly for multi-rotors with mounted flaps, and could be perfectly functional in UAVs powered by thermal engines to increase the autonomy since the propellers cannot be used as controller surfaces.

Primary ciliary dyskinesia (PCD) is an inherited disorder that impairs motile cilia, essential for respiratory health, with a reported prevalence of 1 in 16,309 within Hispanic populations. Despite having the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in 70% of Puerto Rican patients, the characterization of the ciliary dysfunction remains unidentified due to the unavailability of advanced diagnostic modalities like High-Speed Video Microscopy Analysis (HSVA). Our study implemented HSVA for the first time on the island as a tool to better diagnose and characterize the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in Puerto Rican patients. By applying HSVA, we analyzed the ciliary beat frequency (CBF) and pattern (CBP) in native Puerto Rican patients with PCD. Our results showed decreased CBF and a rotational CBP linked to the RSPH4A founder mutation in Puerto Ricans, presenting a novel diagnostic marker that could be implemented as an axillary test into the PCD diagnosis algorithm in Puerto Rico. The integration of HSVA technology in Puerto Rico substantially enhances the framework for PCD evaluation and diagnosis, facilitating prompt detection and early intervention for improved disease management. This initiative, demonstrating the potential of HSVA as an adjunctive test within the PCD diagnostic algorithm, could serve as a blueprint for analogous developments throughout Latin America.

This study introduces a novel method for early prediction of Kimchi cabbage (Brassica rapa subsp. pekinensis (Lour.) Hanelt) height, utilizing drone imagery and a long short-term memory (LSTM) model. The research was conducted on a testbed at the National Institute of Agricultural Sciences (NAS) in South Korea, encompassing two distinct soil types (loam and sandy loam) to investigate their impact on growth. High-resolution drone images were captured throughout the growing season to generate a canopy height model (CHM) for estimating plant height at various stages. Missing height data were interpolated using a logistic growth curve, and an LSTM model was trained on this data to predict the final height of Kimchi cabbage at harvest. Three LSTM models were developed using time-series data collected at 29, 36, and 44 days after planting (DAP). The model trained on data from DAP 44 demonstrated the highest accuracy with a coefficient of determination (R²) of 0.83, a mean absolute error (MAE) of 2.48 cm, and a root mean square error (RMSE) of 3.26 cm, outperforming models trained on earlier data. Color-coded maps were generated to visualize the spatial distribution of predicted Kimchi cabbage heights, revealing variations in growth patterns across the testbed and confirming the model's potential for site-specific management. Considering the trade-off between accuracy and prediction timing, the model trained on DAP 36 data (MAE = 2.77 cm) was deemed optimal for informing cultivation management decisions. This research demonstrates the feasibility and effectiveness of integrating drone imagery, logistic growth curves, and LSTM models for early and accurate prediction of Kimchi cabbage height. The proposed technology enables data-driven decision-making for farmers, facilitating timely interventions based on predicted growth patterns. This could lead to improved crop yields, resource optimization, and a more sustainable agricultural future. Future research will focus on refining the model's accuracy and exploring its applicability to other crops, further expanding the potential of precision agriculture technologies.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Unmanned Aerial Vehicles (UAVs), commonly known as drones, have experienced a significant surge in both civilian and military applications, owing to their versatility and cost-effectiveness. However, a negligent use or the operation with harmful intent of these aircraft poses a potential risk to public safety and the privacy of individuals. In response to this threat, counter-drone systems have been developed in recent years, including technologies to detect, position, and neutralize these aircraft. This paper presents a review of different existing commercial counter-drone systems, the technologies behind detection, tracking, and classification, as well as soft and hard kill mitigation.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

This manuscript explores unmanned aerial vehicle DC motor control performance efficacy of deterministic artificial intelligence in comparison to model-following adaptation, particularly a direct self-tuner with filtering. The deterministic artificial intelligence model made use of self-awareness statements to overcome error in response to permutations of the multi-duty cycle square wave that served as the system input. It can be seen that (despite equivalently powerful estimation techniques) deterministic artificial intelligence provided far superior results: a reduction in peak initial transient error of 55%, and a mean error reduction over 81% with over 65% reduction in error standard deviation compared to a state-of-the-art nonlinear adaptive control method. Deterministic artificial intelligence also was able to very closely track at the switching of the input control, while the benchmark nonlinear adaptive control failed to respond as quickly at these points.

Without the use of medicine drones, users are responsible for transporting goods at a high cost. The goal of this patient monitoring system is to identify people's health and, if necessary, administer medicine. The transportation drone is capable of finding healthcare information in a 360-degree rotation within the transportation infrastructure. IoT: Drone doctors are critical for the transportation of small gadgets such as drug treatments, blood leakages, and vaccines in the critical conditions of a heart patient, in the event of failure of traffic location infrastructure, highway roads, or hospitals due to intense climate or site visitor congestion, and for the transportation of small gadgets such as drug treatments, blood leakages, and vaccines. When transmission is difficult, the self-maintaining drone is the format for quickly transporting drug treatments to the appropriate locations. The shipping drone equipped with an Ardupilot can drive in autopilot mode, which guides the drone to its destination. It has a 7-minute flying period and can deliver up to 2 kg of medicine. When the detected heartbeat is 94bpm and the fever range is 101 degrees, a method has been presented in which an IoT Drone Doctor (IDD) System distributes the first AID box to vulnerable patients and heart patients.

Both drones and laser scanners digitally take the as-built context of an object into the computer and the data taken is transmitted to a Building Information Modeling (BIM) world to create ac-curate 3D models. Although the laser scanner is the leading method of the Scan-to-BIM proce-dure, many professionals indicate drawbacks of the technology and point out the drone is an al-ternative that can improve the shortcomings, leading to the UAV-to-BIM process. Korean con-struction industry plans to implement the drone technology for scrutinizing as-built construc-tion quality by 2025. However, the drone is not popular in the construction projects. Korean universities where Construction Engineering and Management program have been implement-ed are requested to develop a drone curriculum for construction professionals. Since the majori-ty of the professionals are not familiar with drone operation, in order for the schools to be suc-cessful in developing the curriculum, it is very necessary to perform a preliminary experimental study for identifying the essential education contents that are appropriate to drone beginners. The main objective of this paper is to perform the study for the drone beginners and recognize the recommendations and the framework of drone curriculum that will be beneficial for the schools to develop a comprehensive curriculum later on.

The informational synthesis of neural structures, processes, parameters and characteristics that allow a unified description and modeling as neural machines of natural and artificial neural systems is presented. The general informational parameters as the global quantitative measure of the neural systems computing potential as absolute and relative neural power were proposed. Neural information organizing and processing follows the way in which nature manages neural information by developing functions, functionalities and circuits related to different internal or peripheral components and also to the whole system through a non-deterministic memorization, fragmentation and aggregation of afferent and efferent information, deep neural information processing representing multiple alternations of fragmentation and aggregation stages. The relevant neural characteristics were integrated into a neural machine type model that incorporates unitary also peripheral or interface components as the central ones. The proposed approach allows overcoming the technical constraints in artificial computational implementations of neural information processes and also provides a more relevant description of natural ones.

Breast cancer stands as a predominant health concern for women globally. As mammography is the primary screening tool for breast cancer detection, improving the detection of breast cancer at screening could save more lives. This mammography re-view paper provides a systematic review of computer-aided techniques during a specific time frame for the segmentation and classification of microcalcification, evaluating image processing, machine learning, and deep learning techniques. The systematic review is meticulously carried out, adhering closely to the preferred reporting items for Systematic Reviews and Meta-Analysis (PRISMA) guidelines. This article focuses on mammographic breast cancer detection approaches based on automated systems, discussed chronologically from 1970 through 2023. This article encompasses the breadth of artificial intelligence-based methods from the most primitive to the most sophisticated models. Image processing and machine learning-based methods are compre-hensively reviewed. The evaluation of a deep learning architecture based on self-extracted features for classification tasks demonstrated outclass performance. Large-scale datasets required for a broader and in-depth analysis of novel methods for breast cancer detection are also discussed in this article. This research work is aligned with the United Nations' sustainability de-velopment goals.

Abstract: In this paper we describe how the administration of drone brood homoge-nate (DBH) influenced intestinal secretion of IgA, MUC-2, morphometric parameters, peripheral blood values, and expression of cytokines. A total of 12 pigs were divided into three groups, two experimental, first fed with 100 mg DBH.kg-1 (E1), second with 200 mg DBH.kg-1 (E2) of body weight, and a control (C) group without DBH in the di-et. Animals didn't show significant changes in average weight gains and feed conver-sion among evaluated groups. Feeding a diet containing 200 mg DBH.kg-1 of body weight in the E2 group produced an increase (p < 0.05) in the red cell distribution width, the percentage of metabolic activity of blood phagocytes in the peripheral blood, as well as splenic cell subpopulations CD4+ and CD21+. The villi height and their cutting surface were increased in the E2 group (p < 0.01), together with a gradual decrease in the concentration of MUC-2 and sIgA (p < 0.001). Upregulation of IL-8 (p < 0.0001), IL-10 (p < 0.05), and IL-18 (p < 0.001) was found mainly in E2 group. Results suggest, that supplementation of DBH in the feed of pigs formed optimal intestinal homeostasis.drone

Nowadays, inquiries are one of the most important tasks to be executed in order to get valued information. When an inquiry is done to gather information about a human behavior there are some problems inherent to it. One of the main problems is how the information about many different persons can be processed to give good information about their environment. Most of the information gathered by these inquiries is used to analyze the behavior of the respondents. It can be used to estimate the success of a certain product on the market or just to validate the satisfaction of current costumers. The veracity of this information can be critical to model environments with some acceptable level of precision. Modelling environments through Artificial Neural Networks (ANN) is highly common because ANN’s are excellent to model predictable environments using a set of data. ANN’s are good in deal with sets of data with some noise, but they are fundamentally surjective mathematical functions and they aren’t able to give different results for the same input. So if an ANN is trained using data where the same input has different images which can be the case of survey data, this can be a problem for the success of modelling the environment. Therefore is necessary to process the data in order to adjust and eliminate invalid data.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

Video editing is a high-required job, for it requires skilled artists or workers equipped with plentiful physical strength and multidisciplinary knowledge, such as cinematography, aesthetics. Thus gradually, more and more researches focus on proposing semi-automatical and even fully automatical solutions to reduce workloads. Since those conventional methods are usually designed to follow some simple guidelines, they lack flexibility and capability to learn complex ones. Fortunately, the advances of computer vision and machine learning make up the shortages of traditional approaches and make AI editing feasible. There is no survey to conclude those emerging researches yet. This paper summaries the development history of automatic video editing, and especially the applications of AI in partial and full workflows. We emphasizes video editing and discuss related works from multiple aspects: modality, type of input videos, methology, optimization, dataset, and evaluation metric. Besides, we also summarize the progresses in image editing domain, i.e., style transferring, retargeting, and colorization, and seek for the possibility to transfer those techniques to video domain. Finally, we give a brief conclusion about this survey and explore some open problems.

In today’s digital media data communication over the internet increasing day by day. Therefore the data security becomes the most important issue over the internet. With the increase of data transmission, the number of intruders also increases. That’s the reason it is needed to transmit the data over the internet very securely. Steganography is a popular method in this field. This method hides the secret data with a cover medium in a way so that the intruders cannot predict the existence of the data. Here a steganography method is proposed which uses a video file as a cover medium. This method has five main steps. First, convert the video file into video frames. Then a particular frame is selected for embedded the secret data. Second, the Least Significant Bit (LSB) Coding technique is used with the double key security technique. Third, an 8 characters password verification process. Fourth, reverse the encrypted video. Fifth, signature verification process to verify the encryption and decryption process. These five steps are followed by both the encrypting and decrypting processes.

Live video streaming has become one of the main multimedia trends in networks in recent years. Providing Quality of Service (QoS) during live transmissions becomes a challenge due to the stringent requirements for low latency and minimal interruptions. This scenario has led to a high dependence on cloud services, implying a widespread usage of Internet connections, which constrains contexts where an Internet connection is not available. Thus, alternatives such as Mobile Ad Hoc Networks (MANETs) emerge as potential communication techniques. These networks operate autonomously with mobile devices serving as nodes, without the need for coordinating centralized components. However, these characteristics lead to challenges to live-video streaming, such as dynamic node topologies or periods of disconnection. Considering these constraints, this paper investigates the application of Artificial Intelligence (AI)-based classification techniques to provide adaptive streaming in MANETs. For this, a software-driven architecture is proposed to route stream in offline MANETs, predicting the stability of individual links and compressing video frames accordingly. The proposal has been implemented and assessed in a laboratory context, analyzing the model performance and QoS metrics. As a result, the model is implemented in a decision forest algorithm, which provides 95.9% of accuracy. Also, obtained latency values become assumable for video streaming, manifesting a reliable response for routing and node movements.

With end-to-end encryption for video streaming services becoming more popular, network administrators face new challenges in preserving network performance and user experience. Video ads may cause traffic congestion and poor Quality of Experience. Because of the natural variation in user interests and network situations, traditional algorithms for increasing QoE may face limitations. To solve this problem, we suggest a novel method that uses user facial emotion recognition to deduce QoE and study the effect of ads. We use open-access Face Emotion Recognition (FER) datasets and extract facial emotion information from actual observers to train machine learning models. Participants were requested to watch ad videos and provide feedback, which will be used for comparison, training, testing, and validation of our suggested technique. Our tests show that our approach beats the ITU-T P.1203 standard in terms of accuracy by 37.1%. Our method provides a hopeful answer to the problem of increasing user engagement and experience in video streaming services.

Both soybean variety and processing affect product characteristics. This study’s objective was to characterize the effect of four extraction methods (variations of soaking and grinding) combined with cooking on the content and composition of phenolic substances, antioxidant and anti-DU145 prostate cancer cell proliferative properties of soymilk prepared from a yellow soybean of the ProSoy variety, which is a high protein variety. Results showed soymilk processing yield was the greatest by Method 4, but Method 2 gave the highest solids and protein yields by about 14 and 12%, respectively. Method 4, a two-step grinding also increased yields (8 and 7%, for solids and protein, respectively), and in all but one instance produced higher total phenolic content (TPC), total flavonoid content (TFC), condensed tannin content (CTC) and total isoflavone content in both raw and cooked soymilk as compared to Method 1. Cooking soymilk reduced 14-17% of total phenolic substances. Cooking reduced anticancer capacity of Method-4-prepared soymilk phenolic extract by increasing IC50 value from about 4.9 mg/mL to 6.8 mg/mL. The increases in phenolic compounds and antioxidants produced in Prosoy soymilk by Methods 2 and 4 with simultaneous increases in product solids yield are significant to benefit the soymilk industry and consumer health. Keywords: ProSoy yellow soybean, soymilk processing, phenolics, isoflavones, antioxidant capacity, anti-DU145 prostate cancer proliferation

To better understand effects of agronomic practices on yield-nutrition relationships in wheat (Triticum aestivum L.) grains for Zn biofortification while improving yields simultaneously, effects of different soil fertilization and different drone-based foliar spraying treatments were investigated. The mixture of Zn or increasing N but simultaneously reducing P in compound fertilizers were all practical to increase grain yields and Zn concentrations in calcareous soils tested. However, the overall effects are limited, with a maximal yield increase by only 7.0% and a maximal increase of the grain Zn density from 19.4 to 27.0 mg/kg, which is far below the target biofortification value of 40-50 mg/kg. Unfortunately, there was a negative side effect, which decreased Fe and Mn concentrations and the Fe bioavailability. Notably, grain yields and Zn concentrations were significantly increased by drone-based foliar Zn sprayings from 7.5 to 8.6~8.8 t/ha by 12.0-17.3% and from 33.5 to 41.9~43.6 mg/kg by 25.1~30.1%, respectively, indicating a double-win in yield and nutrition. A spraying of ZnSO4·7H2O increased grain Zn concentrations and accumulation more so than ZnO, indicating the importance of chemical Zn forms in determining the effectiveness of foliar spraying. Moreover, foliar Zn sprayings simultaneously increased grain concentrations and accumulation of Fe, Mn and Cu, demonstrating multiple benefits. There were positive correlations between Zn and Fe, Mn or Cu, indicating synergistic but not antagonistic interactions. Compared to micronutrients, concentrations of grain macro- and medium nutrients (N, P, K, Ca, Mg) were less affected. Thus, a double-win in grain yields and micronutrient (particulaly for Zn) nutrition could be effectively achieved through appropriate soil fertilization and foliar Zn spraying. These results provide a better understanding of the yield-nutrition relationship among wheat grain yields, Zn and other nutrient elements for a better integrated manipulation to achieve a win-win situation in yield and nutrition.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

The goal of the manuscript is to design a relatively best control structure for the noise suppression of a drone’s camera gimbal action. The gimbal’s movement can be simplified as a rest-to-rest reorientation system that can achieve the boundary result of a dynamic system. Six different control architectures are proposed and evaluated based on their ability to control the trajectory of the dynamic-system position and speed, their running time, and quadratic cost. The robustness of the control architecture to uncertainties in inertia and sensor noise is also analyzed. Monte Carlo figures are used to assess the performance of the six control systems. The conditions for applying different architectures are identified through this analysis. The analysis and experimental tests reveal the most suitable control of the drone’s camera gimbal rotation.

Quadrotor drones have rapidly gained interest recently. Numerous studies are underway for the commercial use of autonomous drones, and especially the distribution businesses are taking serious reviews on drone delivery services. However, there are still many concerns about urban drone operations. The risk of failures and accidents makes it difficult to provide drone-based services in the real world with ease. There have been many studies that introduced supplementary methods to handle drone failures and emergencies. However, we discovered the limitation of the existing methods. The majority of approaches were improving PID-based control algorithms which is the dominant drone control method. This type of low-level approach lacks situation awareness and the ability to handle unexpected situations. This study introduces an event-based control methodology that takes a high-level diagnosing approach that can implement situation awareness via time-window. While leaving the low-level controller to involve in operating the drone for most of the time in normal situations, our controller operates at a higher level and detects unexpected behaviors and abnormal situations of the drone. We tested our method with real-time 3D computer simulation environments with Unreal Engine[15] and AirSim[31]. We were able to verify that our approach can provide enhanced double safety and better ensure safe drone operations. We hope our discovery to possibly contribute to the advance of real-world drone services in the near future.

While maintenance dredging of port access channels is often required to maintain navigability, it can result in increased turbidity, sediment plumes, and associated reductions in water quality. Unoccupied aircraft systems (UAS, or drones) are increasingly applied to study water quality due to their high spatial and temporal resolutions. In this study, we investigated the use of drone imagery to monitor turbidity in the Morehead City Harbor, North Carolina, USA, during channel maintenance by hopper dredge. Drone flights were conducted concurrently with in-situ sampling during active dredging and post-dredging. Multispectral drone images were radiometrically calibrated, converted to reflectance and then turbidity using two separate processing methods and a single-band (red; 620nm-700nm) generic turbidity retrieval algorithm, and then compared to in-situ measurements. The method of using average reflectance to retrieve a single turbidity measurement per drone image produced agreeable results when compared to the in-situ measurements (R² = 0.84). This method was then used to generate turbidity maps and extract surface plumes. While this could be considered a limited validation, the results indicate that realistic values can be obtained from drone imagery for low and high turbidity concentrations (1-72 FNU), making drones a viable option for monitoring surface turbidity associated with dredging.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

With a view to understand and resolve the complexity of the food matrix, ohmic technologies alone or in combination were extensively employed. In this sense, the newest developments and advances of proteomics, metabolomics, lipidomics whith their unique benefits could simplify and understand the link between physiological and pathological activities in biology, physiology, pathology, and food science and processing. This review aims to briefly introduce the basis of proteomics, metabolomics, lipidomics, then expansively review their impact on the assessment of meat quality and safety. Here, also, we discuss the application of proteomics, metabolomics, lipidomics for the authentication and adulteration of meat and meat derivatives from different sources, and provides some perspectives regarding the use of emerging techniques such as rapid mass spectrometry (MS) and non-invasive measurements for the analysis of meat quality and safety. This paper summarizes all significant investigation in these matters, and underlines the advances in analytical chemistry technologies and meat science areas. By emphasizing the requirement for additional examinations, this paper attempts a comprehensive knowledge of “foodomics” and their potential to improve their employment in meat science.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

For a wide field of view (FoV) wavefront coding athermalized infrared imaging system with a single decoding kernel, the off-axis aberration tends to cause artefacts. In order to correct off-axis aberration, many pieces of lenses will reduce the transmission efficiency and increase the weight and cost. To meet requirements for wide FoV, wide operating temperature and low weight of infrared imaging systems, this paper reports a wide-FoV wavefront coding athermalized infrared imaging system with a two-piece lens. Its principle, design, manufacture, measurement and performance validation are successively discussed. This paper constructs an optimization problem which maximizes the weighted mean of PSF consistency for both the FoV and operating temperature range. The two-piece lens contains four surfaces, where three aspheric surfaces are introduced to reduce optical off-axis aberrations and a cubic surface is introduced to achieve athermalization. The optical phase mask containing an aspheric surface and a cubic surface is manufactured by nano-metric machining of ion implanted material(NiIM). Experimental results validate that our wide-FoV wavefront coding athermalized infrared imaging system has a full FoV of 26.10° and an operating temperature over -20°C to +70°C.

Superpixels are a representation of still images as pixel grids because of their more meaningful information compared with atomic pixels. However, their usefulness for video classification has been given little attention. In this paper, rather than using spatial RGB values as low-level features, we use optical flows mapped into hue-saturation-value (HSV) space to capture rich motion features over time. We introduce motion superpixels, which are superpixels generated from flow fields. After mapping flow fields into HSV space, independent superpixels are formed by iteration of seeded regions. Every grid of a motion superpixel is tracked over time using nearest neighbors in the histogram of flow (HOF) for consecutive flow fields. To define the temporal representation, the evolution of three features within the superpixel region, namely the HOF, HOG, and the center of superpixel mass are used as descriptors. The bag of features algorithm is used to quantify final features, and generalized histogram-kernel support vector machines are used as learning algorithms. We evaluate the proposed superpixel tracking on first-person videos and action sports videos.

The expansion of Open World Video Games (OWVGs) has seen the emergence of multiple new fictional worlds. This type of video game is characterized by total immersion in a world built for the players entertainment. What videogames developers want when players enter an OWVG is that they could feel like if they were open a door to an entirely new world and leave the real world behind. These virtual worlds manifest as a complement, an alternative, or the successor to the physical universe, and in some way continue the philosophical tradition of possible worlds begun by Leibniz. Accustomed to ‘surviving’ in hostile environments, millions of people continued to improve their skills in the midst of the COVID-19 pandemic while locked in their homes. Once the pandemic seems to start to be left behind, the paper analyzes the virtual worlds created by the video games and the relations between the pandemic and these fictional worlds.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Since the beginning of the internet era, there has been an explosion of growth in structured data (such as numbers, symbols, and labels) as well as unstructured data (including images, videos, and text). Efficient and accurate mixed query of these two types of data is a key technology to achieve high-quality information retrieval, and it is also a major challenge that needs to be solved urgently in the industry. In this study, we employ an advanced Transformer model that combines strategies and fine-tuning techniques for multi-task learning. Specifically, the model is first pre-trained on a large-scale, general-purpose dataset to learn different types of data representations and basic language comprehension skills. After that, we fine-tuned the parameters of the model to better suit these specific data processing tasks for specific application scenarios, such as image annotation, video content analysis, and structured data query. At the heart of the model is the self-attention mechanism, which allows the model to automatically emphasize the important parts and ignore irrelevant information when processing the input data. In addition, we have introduced task-specific adaptation layers that are designed to add additional processing power to the original Transformer architecture, such as a semantic analysis layer for unstructured text data and a relational extraction layer for structured data. This combination of general pre-training and task-specific fine-tuning allows the model to flexibly process and integrate information from different data sources, improving processing efficiency and accuracy. Experimental results show that the model performs well in a variety of data processing tasks, significantly improves the accuracy and efficiency of information retrieval, and verifies the strong potential and adaptability of large language models in processing mixed data types.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

In the era of electrification and artificial intelligence, direct current motors are widely utilized with numerous innovative adaptive and learning methods. Traditional methods utilize model-based algebraic techniques with system identification, such as recursive least squares, extended least squares, and autoregressive moving averages. The new method known as deterministic artificial intelligence asserts physical-based process dynamics to achieve target trajectory tracking. There are two common autonomous trajectory generation algorithms: sinusoidal function and Pontryagin's based generation algorithm. This thesis aims to simulate model-following and deterministic artificial intelligence methods using sinusoidal and Pontryagin's methods and compare their performance difference when following challenging step function slew maneuver.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

Fragile X syndrome (FXS) is caused by the full mutation in the FMR1 gene on the Xq27.3 chromosome region. It is the most common monogenic cause of Autism Spectrum Disorder (ASD) and inherited intellectual disability (ID). Besides ASD, ID and other issues, individuals with FXS may exhibit sleep problems and impairment of circadian rhythm (CR). The Drosophila melanogaster models of FXS, such as dFMR1B55, present excellent model for research in the FXS field. During this study, sleep pattern and CR in dFMR1B55 mutants were analyzed, using a new platform based on continuous high-resolution videography in integration with a highly-customized version of software. This methodology provides more sensitive results, which could be crucial for all further research in this model of fruit flies. The study revealed that dFMR1 B55 male mutants can be considered weak rhythmic flies rather than totally arrhythmic, and present a good alternative animal model of genetic disorder, which includes impairment of CR and sleep behavior. The combination of videography and software used in the current study should be recommended as a gold-standard methodology for such further research.

This study provides an evaluation of a web-based platform for game management and sales, developed using PHP, MySQL, and SASS. The development process utilized the SCRUM methodology, concentrating on essential modules such as user management, game catalog, payment processing, and technical support. The platform's performance was assessed using Google's Lighthouse tool, which evaluates four critical areas: performance, accessibility, best practices, and SEO. The results demonstrated exceptional performance with a score of 99/100 and perfect adherence to best practices with a score of 100/100, reflecting high efficiency and compliance with web development standards. Accessibility received a score of 83/100, indicating potential areas for improvement, while SEO achieved a score of 91/100, suggesting effective search engine optimization. The findings reveal that the platform exhibits high levels of optimization and operational efficiency. However, there remains an opportunity to enhance accessibility features. This study highlights the significance of rigorous web development practices and optimization efforts in achieving superior performance and user experience in web-based systems.

Sign language recognition technology can help people with hearing impairments to communicate with those who are hearing impaired. At present, with the rapid development of society, deep learning technology also provided certain technical support for sign language recognition work. In sign language recognition tasks, the use of traditional convolutional neural networks to extract spatio-temporal features from sign language videos suffers from insufficient feature extraction, resulting in low recognition rates. Nevertheless, video-based sign language datasets are very large and require a lot of computational resources for training and generalisation must be ensured, which poses a challenge for recognition. In this paper, we have presented a video-based sign language recognition method based on resnet and lstm. As the number of network layers increases, the ResNet network can effectively solve the granularity explosion problem and obtain better time series features. We use the Resnet convolutional network as the backbone model. At the initialisation stage, we obtain sign language features using ResNet; then, the learned feature space is used as the input of LSTM network to obtain long sequence features. The experimental results show that the accuracy of the above model is better than the mainstream model, and it can effectively extract the spatio-temporal features in sign language videos and improve the recognition rate of sign language actions.

The use of video in education has become ubiquitous as technological developments have markedly improved the ability and facility to create, deliver and view videos. The concomitant pedagogical transformation has created a sense of urgency regarding how video may be used to advance learning. Initial reviews have suggested only limited potential for the use of video in higher education. More recently, a systematic review of studies on the effect of video use on learning in higher education, published in the prestigious Review of Educational Research, found, overall, effects to be positive. In the present paper we critique this study and provide some needed clarity to the state of research on learning via video in higher education. We reveal significant gaps in the study methodology and write-up and use a cognitive processing lens to critically assess and reanalyse study data. We found results of this study to be only applicable to learning requiring lower-level cognitive processing and conclude, consistent with prior research, learning benefits remain limited.