This paper introduces an open-source active high-precision signal amplifier designed for enhancing biodata acquisition, specifically focusing on EEG signals. The compact device, with a diameter of 18 mm, seamlessly integrates electronics, signal processing, and meticulous design considerations. Incorporated within the single board are circuits for low-noise amplification, an analog interface equipped with bandpass filters, and an integrated ADC for precise digitization. A comprehensive evaluation of signal quality has been conducted, encompassing aspects such as noise levels, electrode bias tolerance, and common mode rejection ratio. To facilitate this evaluation, the widely recognized Silver Chloride electrode (Ag/AgCl) has been employed. Additionally, this paper delves into an extensive discussion concerning diverse sources of noise, along with strategies to curtail input noise and minimize noise originating from electrodes and amplifiers. Leveraging the substantial advancements achieved in the design of dry contact electrodes, this specific device is poised to carve a notable niche in the realm of brain-computer interface.

A total of 27 microsatellites markers , scattered all over the genom of barley, were used for characterization,and diversity analysis in 33 barley (Hordeum vulgare L.) accessions and cultivars of Algeria.Over the 27 genetic loci studied, 110 alleles were identified with a mean of 4.1 alleles per locus and the average polymorphism information content (PIC) of 0.46,the marker Ebma0806 showed the greatest value of PIC with 0.83.Genetic diversity at 27 microsatellite loci varied from 0 to 0.84 (Mean=0.50) for 33 Algerian cultivars. The genetic distance among the cultivars ranged from 0.2 to 0.85. Cluster analysis and principal coordinate analysis (PCoA) based on the SSR data clearly differentiate the all genotypes studied.

Graphene was synthesized through a two-step pyrolysis method using waste candlenut (Aleurites moluccanus) shells as the precursor. Cerium (Ce)/graphene composites were prepared via an impregnation technique. The resulting graphene and Ce/graphene were characterized using various analytical methods, including Scanning Electron Microscopy with Energy-Dispersive Spectroscopy (SEM-EDS), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Thermo Gravimetric Analysis (TGA), Fourier Transform Infrared (FTIR) spectroscopy, Cyclic Voltammetry (CV), and Linear Sweep Voltammetry (LSV). The bio-carbon produced predominantly exhibited a graphene structure with flat carbon morphology and an interlayer distance of 0.33 nm. This structural information is supported by XRD data, which shows a broad and weak peak at 2θ = 26° corresponding to the C (002) plane, indicative of graphene presence. FTIR, XPS, and Raman spectroscopy further confirmed the presence of graphene through the detection of Csp2 aromatic bonds and the characteristic D, G, and 2D peaks. Notably, the performance of cerium can be enhanced by the incorporation of graphene, attributed to the large surface area and chemical interactions between Ce and graphene. Consequently, candlenut-derived graphene shows potential as a supportive material for modifying the properties of cerium, thereby opening avenues for various advanced applications, such as sustainable and high-performance energy storage systems.

This work presents a novel compact CMOS potentiostat designed circuit for electrochemical cell. The proposed topology functions as a circuit interface, controlling the polarization of voltage signals at the sensor electrodes and facilitating current measurement during the oxidation-reduction process of a analyzed solution. The potentiostat, designed for CMOS technology, comprises a two-stage amplifier, two current mirror blocks coupled to this amplifier, and a CMOS push-pull output stage. It employs the electrochemical method of cyclic voltammetry, operating within voltage range of ±0.8 V and scan rates of 10mV/s, 25mV/s, 100mV/s and 250 mV/s. The circuit is capable of reading currents ranging from 10 µA to 500 µA. Experimental results were obtained using a potassium ferrocyanide (K3(FeCN)6) redox solution with concentrations of 10, 15 and 20 mmol/L, and their corresponding voltammograms were evaluated. The experimental results from a discrete circuit demonstrate that the proposed potentiostat topology produces outcomes consistent with those of classical topologies presented in the literature and industrial equipment.

This study aims at providing a climatological analysis of annual and long-term variability of dry periods in the Polish Carpathians in the period of 35 years between 1986 and 2020. Aside days with precipitation, dry periods, namely sequences of days with no precipitation, constitute an inherent characteristic of the climate. The input data for the research was formed by daily precipitation totals from 17 meteorological stations acquired from the Institute of Meteorology and Water Management - National Research Institute, and T. Niedźwiedź catalogue of circulation types over southern Poland. Frequency of dry periods of different duration has been presented. The incidence of long-term periods has been related to the atmospheric circulation. An analysis was performed regarding the change of the average quantity and average length of dry sequences in the 35-year period covered. At most stations, there were no statistically significant trends with respect to the analysed dry day characteristics. This is an obvious result of high variability year-to-year, which means that exclusively large changes may achieve statistical significance. Dry days have been evidenced to related to circulation types. A vast majority of dry days is related to anti-cyclonal systems, particularly the anti-cyclonal wedge (Ka) and western anti-cyclonal (Wa) situations.

Nowadays, rotor-stator mixers are widely used in the chemical process industry to carry out the dispersion and de-agglomeration processes for manufacturing the homogenous electrode slurries. Development of the process simulation models for the turbulent mixing of these slurries helps to optimize the mixing parameters such as rotational speed and dispersion time. In this work, computational fluid dynamics (CFD) approach through ANSYS Fluent are explored to determine and analyze the flow patterns, velocity fields and viscosity distribution during the dispersion of anode slurries. It utilizes a non-homogeneous Eulerian multiphase approach and the typical k-ε model to create turbulence fields and compute the mixing rate. This work significantly improves our understanding of the relationship between rotor speed, dispersion time, viscosity distribution, and mixer geometry in rotor-stator mixers.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

The aim of this study is to present the spatial and temporal variability of the frequency of dry and wet days and dry and wet spells against the background of changes in precipitation and atmospheric circulation. The study is based on daily precipitation totals from 46 meteorological stations in Poland for the years 1966-2023. Additionally seven circulation indices were used: GBI, NAO, AO, EA, EA/WR. SCAND ana AMO. Dry days are defined as days without precipitation. Wet days are days with at least 1 mm of precipitation. It was shown that dry spells are much more common that wet spells, are longer and cover larger areas. Long term changes in annual characteristics of dry and wet days and spells are statistically insignificant. Only the length of the longest dry spell in the year increases. However, there are significant changes in their annual cycles. Spring is drier, in summer months, precipitation decreases in the south and increases in the north, November and December, symbols of gloomy rainy weather, are increasingly drier, rainy weather moved to January and February. The impact of circulation varies with seasons and NAO, Ao, SCAN and GBI indices have the strongest impact.

Wildfires have always been a part of the history of Mediterranean forests. However, forest regeneration after a wildfire is not certain. It depends on many factors, some of which may be influenced by land management activities. Failure of regeneration will cause a regime shift in the ecosystem, reducing the provision of ecosystem services and ultimately leading to desertification. How can we increase Mediterranean forests’ resilience to fire? To answer this question, we did a literature review, investigating chains of processes that allow forests to regenerate (which we label “regeneration mechanisms”), and assessed the impact of selected management practices documented in the WOCAT database on the regeneration mechanisms. We identified three distinct regeneration mechanisms that enable Mediterranean forests to recover, as well as the time frame before and after a fire in which they are at work, and factors that can hinder or support resilience. The three regeneration mechanisms enabling a forest to regenerate after a fire consist of regeneration (1) from a seed bank; (2) from resprouting individuals; and (3) from unburned plants that escaped the fire. Management practices were grouped into four categories: (1) fuel breaks, (2) fuel management, (3) afforestation, and (4) mulching. We assessed how and under what conditions land management modifies the ecosystem’s resilience. The results show that land management influences resilience by interacting with resilience mechanisms before and after the fire, and not just by modifying the fire regime. Our analysis demonstrates a need for adaptive – i.e. context- and time-specific – management strategies.

Non-viral mediated plasmid DNA transfection by electroporation (EP) is an established method for gene transfection. In this study, the usefulness of direct EP at an intradermal (i.d.) site (D_EP) with implanted electrodes to achieve a high protein expression level was investigated. In addition, D_EP application with various intervals with a low application voltage was also evaluated to confirm its effect on protein expression. A higher protein expression level was observed after green fluorescent protein (GFP)- and luciferase-encoding DNA were delivered by i.d. injection followed by D_EP application. When luciferase expression was observed with an in vivo imaging system, continuous expression was confirmed over 21 days after i.d. injection followed by D_EP at 100 V. This approach provided increased gene expression levels compared with conventional EP methods via the stratum corneum layer. In addition, the effect of application voltage on luciferase expression was investigated; two-time applications (repeated D_EP) at 20 V with 5 min intervals showed similar luciferase expression level to single D_EP application with 100 V. Histological observations showed the skin became thicker after a single D_EP at 100 V, whereas no apparent thickness changes was confirmed after repeated D_EP at 20 V with 5 min intervals. This study revealed that direct i.d. voltage application achieved high protein expression levels even at low voltages. Skin is a promising administration site for DNA vaccines, so this approach may be effective in DNA vaccine delivery into skin tissue.

From the theory of relativistic chemical kinetics [M. W. Baig, Int. J. Mod. Phys. B 31, 1750177 (2017)] relativistic thermodynamics and kinetics for electrode processes have been developed to explain time dilation for electrode processes. For a moving observer moving at fractions of the speed of light, cell potential is observed to decrease. This results in the slower oxidation and reduction of ions at the respective electrodes. The newly formulated Lorentz transformation of the electrode and cell potential is explained in terms of generation of spin 2-boson “gravitons” from fusion of spin-1 boson “virtual-photons” mediating electrostatic force of attraction between ions and electrodes. It is postulated that birth of spin 2-boson i.e. gravitons is followed by their eventual escape in any of higher 4+n dimensions. To demonstrate the effectiveness of the present theory, the Daniel cell is considered as a numerical example.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Along with the rapid development of technology and industry, the need for energy storage has become fundamental. One promising energy storage devices is the supercapacitor. Several type supercapacitors are available, one of which is the electrical double-layer capacitor made from carbon graphite and multiwalled carbon nanotubes (MWCNTs). In this study, we combined these two materials into a working electrode in a three-electrode system. In the morphological analysis using scanning electron microscope, transmission electron microscope, and X-ray diffraction, the two materials were found to have formed a composite on the surface. In the electrochemical analysis, two types of testing were conducted using cyclic voltammetry and electrochemical impedance spectroscopy. Electrochemical analysis was carried out on five electrolyte concentrations of Na2SO4 from 1 to 6 M. The capacitance produced at concentrations of 1, 2, 3, 4, and 5 M were 34.395, 35.808, 46.284, 49.502, and 76.815 F/g, respectively. At an electrolyte concentration of 5 M Na2SO4, an energy density of 27.312 Wh/Kg and a power density of 343.786 W/Kg were produced. Meanwhile on concentration of 6 M, the surface of the electrode was damaged.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

The study evaluated the regenerative responses of the lacrimal functional unit (LFU) after Lacrimal Gland (LG) ablation. The LG of Wistar rats were submitted to G1) partial LG ablation, G2) partial ablation and transplantation of an allogeneic LG, or G3) total LG ablation, (n=7-10/group). The eye wipe test, slit-lamp image, tear flow, and histology were evaluated. RT-PCR analyzed inflammatory and proliferation mediators. The findings were compared to naïve controls after 1 and 2 months (M1 and M2). G3 presented increased corneal sensitivity, and the 03 groups have shown corneal neovascularization. Histology revealed changes in LG, and corneal inflammation. In the LG, there was an increase in MMP-9 mRNA of G1 and G2 at M1 and M2 and RUNX-1 at M1 and M2 in G1 and RUNX-3 mRNA at M1 in G1, and in G2 at M2. TNF-α mRNA rose in the corneas of G1 and G2 at M2. There was an increase in the IL-1β mRNA in the Trigeminal Ganglion of G1 at M1. Without changes in tear flow or evidence of LG regeneration, LG ablation or grafting are unreliable models for dry eye or LG repair in rats. The surgical manipulation extended inflammation to the LFU.

Electrode degradation in continuous resistance spot welding process of BH 220 steel was evaluated by electrode life test, and weldability tests were conducted by geometry features measurement, mechanical property analysis, and electrode diameter measurement with 88 or 176 weld intervals. The analysis of weld geometry shows that the HAZ width, nugget diameter, and nugget area tend to decrease rapidly, while the nugget height tends to firstly increase with the weld repetitions till the welding heat input becomes too small to form the valid nugget. The peak load shows a rapid downward trend, while failure energy and maximum displacement slightly increase till the 176th weld and then decrease. The cavities and pores in the nugget mainly appear after the 176th spot weld. The electrode diameter increases during welding. The reason for the increase in electrode diameter may be that the contact area between the electrode and BH 220 steel sheets becomes smaller in the welding process, which causes the continuous sticking phenomenon between the electrode and the BH 220 steel sheets. In the absence of alloying, the edge of the electrode is geometrically deformed, while Cu-Zn-Fe alloying occurs in the area in contact with the BH 220 steel sheet.

Intermittent religious fasting increases a risk of hypo- and hyperglycemia in individuals with diabetes, but its impact in those without diabetes is poorly investigated. The study aim was to examine the effects of religious Bahá'í fasting (BF) on glycemic control and variability and compare these effects with time-restricted eating (TRE). In a three-arm randomized controlled trial, 16 subjects without diabetes were assigned to a BF, 16:8 TRE or control group. Continuous glucose monitoring and food intake documentation was conducted before and during the 19 days of intervention, and 24-hour mean glucose, glycemic variability indices, and glucotypes were assessed. BF and TRE groups, but not the control group, markedly reduced the daily eating window while maintaining macronutrient composition. Only the BF group decreased caloric intake (-677.8 ± 357.6 kcal, p=0.013), body weight (-1.92 ± 0.95 kg, p=0.011) and BMI (-0.65 ± 0.28 kg, p=0.006). Higher maximum glucose values were observed during BF in the within-group (+1.41 ± 1.04, p=0.039) and between-group comparison (BF vs. Control: p= 0.010 and TRE vs. BF: p= 0.022). However, there were no alterations of 24-hour mean glucose, intra- and inter-day glycemic variability indices, or glucotypes in any group. Proportions of time above and below range (70-180mg/dl) and HbA1c values remained unchanged. BF and TRE do not exhibit negative effects on glycemic control and variability in subjects without diabetes.

Electrochemical energy conversion and storage is key for the use of regenerative energies at large scale. A thorough understanding of the individual components, such as the ion conducting membrane and the electrode layers, can be obtained with scattering techniques on atomit to molecular length scales. The largely heterogeneous electrode layers of High-Temperature Polymer Electrolyte Fuel Cells are studied in this work with small- and wide-angle neutron scattering at the same time with the iMATERIA diffractometer at the spallation neutron source at J-PARC, opening a view on structural properties on atomic to mesoscopic length scales.

Background and Objectives: Age-related macular degeneration (AMD) is one of the major causes of central vision loss in the older age group and its dry form accounts for the majority of cases. Although several causes and mechanisms for the development and progression of AMD have previously been identified, the pathogenesis of this complex disease is still not entirely understood. As the inflammation and involvement of the immune system are strongly suggested to have a central role to promote the degenerative process and to stimulate the onset of complications, we aimed to analyze the prevalence of serum anti-retinal (ARA) and anti-endothelial cell antibodies (AECA) in patients with dry AMD and to determine their relationship with the clinical features of the disease, notably area of geographic atrophy (GA). Materials and Methods: We enrolled 41 patients with dry AMD and 50 sex- and age-matched healthy controls without AMD. The presence of ARA was determined by indirect immunofluorescence using monkey retina as an antigen substrate, while the presence of AECA was determined using cultivated human umbilical vein endothelial cells and primate skeletal muscle. Results: ARA were detected 36 (87.8%) AMD patients (titers range from 1:20 to 1:320) and in 16 (39.0%) (titers range from 1:10 to 1:40) of controls (p=0.0000). Twenty of the 41 patients (48.8%) were positive for AECA, while in a control group AECA were present only in 5 sera (10.0%). The titers of AECA in AMD patients ranged from 1:100 to 1:1000 and in the control group the AECA titers were 1:100 (p=0.0001). There were no significant correlations between the presence of AECA and disease activity. Conclusions: This study provides evidence for the possible involvement of an autoimmune process against retina and retinal vessel antigens in the pathogenesis of geographic atrophy associated with dry AMD.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

Numerous studies on evaporative cooling systems have been conducted globally, but there is a scarcity of investigations in eastern Africa. The few studies undertaken in this region have primarily focused on their application in food storage and preservation, rather than for building purpose. The goal of this study is to review the most recent advancements in evaporative cooling technology, which would be relevant in eastern Ethiopia and could provide adequate cooling, give adequate thermal comfort, use less energy, and minimize environmental effect in hot and dry areas. There aren't many studies on evaporative cooling systems for building applications in Eastern Africa as a whole, thus this review has taken into account studies conducted in regions with climates similar to eastern Ethiopia. This study covers the classification, operation, and performance of evaporative cooling systems in hot and dry climate. Evaporative cooling systems work well in hot and dry climates, as revealed by this review study.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

The novelty of this study consists in: i) synthesis and characterization of electrode materials recycled from a spent car battery and doped with MnO2 and CuO by the analysis of X-ray diffraction (XRD), Infrared (IR) and Electron Paramagnetic Resonance (EPR) data and ii) the investigation of electrochemical properties of prepared materials in view of new applications as electrode materials for battery. Electron Paramagnetic Resonance (EPR) data indicate that the intensity of the resonance line corresponding to the Cu+2 ion was modified with the increase of the dopant content. The analysis of X-ray Absorption Spectroscopy (XAS) data indicates that by increasing the dopant content there is a process of ordering the oxygen atoms around the lead similar to the PbO2 theoretical model. The electrochemical performances of the recycled and manganese-copper-doped materials are optimized for applications as new anodic electrode for the car battery.

The aging ability of dry white wines has been increasingly recognised. The present work aimed to understand which sensory factors drive their quality evaluation by experienced tasters. Individuals assessed several aesthetic, synthetic, and analytic flavour attributes, using dark tasting glasses. Wines originated from the grape varieties Alvarinho, Arinto, Sauvignon Blanc and Pinot Bianco with a wide range of ages. Basic physical-chemical analysis, browning (Abs 420 nm), elemental composition and a partial volatile fraction were also determined. The overall quality scores were a function of complexity and balance and were negatively influenced by the perception of faultiness. The different ages could be associated with a continuous sensory space characterised by a decreasing perception of freshness and an increase in the mellowed flavours. All wines shared an austere in-mouth perception elicited by their acidity, saltiness, bitterness, smoothness and dryness. Nevertheless, quality scores were similar from the youngest to the oldest-tasted wines (17 years old). The exception was a Sauvignon Blanc wine from a recent vintage that was judged as faulty due to the perception of earthiness. Overall, the tasted wines displayed an unexpected aging ability as demonstrated by the difference between the predicted and real wine ages. To improve the recognition of old wines, the metaphor “mellowed by age” is proposed to describe flavours resulting from beneficial aging instead of “oxidised by age”.

The popular appreciation of dry white wines is most frequently directed to young wines. However, present consumption trends comprise the valorisation of aged dry white wines. Therefore, the present work was aimed at the sensory analysis of these wines with different ages to define their sensory space and to understand which factors drive their quality evaluation by experienced tasters (critics, oenologists and students). Individuals were asked to evaluate several synthetic and aesthetic attributes and to characterise the analytic sensory profile through a Check-All-That-Apply (CATA) methodology. The quality evaluations were differently correlated with wine synthetic parameters according to the taster group. For both critics and oenologists, overall quality scores were driven by persistence and complexity. Moreover, quality was also highly correlated with power for critics and with balance for oenologists. Quality scores were highly correlated with wine browning (absorbance at 420 nm) for critics. The tasting panel showed a homogeneous analytic description of aroma, taste and mouthfeel consistent with wine age. The different ages could be associated to a continuous sensory space characterised by a decreasing perception of freshness and increase in mature and mellowed descriptors. All wines shared an austere in-mouth perception elicited by their acidity, saltiness, bitterness, smoothness and dryness. The age prediction showed that most tasters failed to guess the age wines with more than roughly 13 years old, indicating that tasters were not familiar with the sensory features of white wines with 17 to 46 years old. In conclusion, experienced tasters consistently described the sensory space and recognised the high quality of aged dry white wines. Education programs may use the defined sensory spaces according to aging and to expand the range of quality perception by consumers.

Droplet-based microfluidics has revolutionized numerous fields such as biomedical research, pharmaceuticals, drug discovery, food engineering, flow chemistry, and cosmetics. This paper presents a comprehensive study focusing on the detection and characterization of droplets with volumes in the nanoliter range. Leveraging the precise control of minute liquid volumes, we introduced a novel spectroscopic On-Chip microsensor equipped with integrated microfluidic channels for droplet generation, characterization, and sensing, simultaneously. The microsensor, designed with Interdigitated-Ring-Shaped Electrodes (IRSE) and seamlessly integrated with microfluidic channels, offers enhanced capacitance and impedance signal amplitudes, reproducibility, and reliability in droplet analysis. We were able to make analyses of droplets length in the range 1.0-6.0 mm, velocity 0.66-2.51 mm/s, droplet volume 1.07nL-113.46nL. Experimental results demonstrated that the microsensor's has a great performance in terms of droplet size, velocity, and length, with a significant signal amplitude of capacitance and impedance, and real-time detection capabilities, thereby highlighting its potential for facilitating microcapsule reactions and enabling on-site real-time detection for chemical and biosensor analyses on-chip.

Beef dry aging consist in a selection of unpackaged primal cuts that are placed in a refrigerator room with controlled environment for several weeks. The goals are the concentration of flavor, like nutty and beefy and tenderness improvement. In this study it was intended verify the microbiological and physicochemical behavior and the meat sensorial perception during a process example of meat dry aging. Twelve beef loins were selected for 90 days of dry aging and placed in a refrigerator room with average temperature, relative humidity and forced air 3.17 ± 0.68 °C, 60.65 ± 4.23 % and 0.5-2 m/s, respectively. On 1, 14, 21, 35, 60 and 90 days of dry aging, were taken two samples, crust and lean meat for microbiological counts, pH, aw, color L*a*b* and sensorial analysis. During drying, there weren´t any pathogenic bacteria counts and the average counts were higher for the crust. The aw and pH had an average of 0.98 ± 0.02 and 5.77± 0.015, with a slightly decrease and increase respectively (P<0.05) along aging days. The dry aging process practices, with room refrigeration at RH<65.00% and temperature <4.00 °C can be the reason for aw<0.98 and meat pH<6.00 and therefore for the absence of pathogenic bacteria. The lower microbial counts on the lean meat and the overall acceptability assessed by the sensory panel confirm the importance of the good trimming and storage practices for the dry aged beef.

The study examines projected changes in dry- and wet-spell probabilities in West Africa using a Markov chain approach. Four simulations of regional climate models from the CORDEX-Africa program were used to analyze projected changes in intraseasonal variability. The results show an increase in the probability of having a dry day, a dry day preceding a wet day and a dry day preceding a dry day, and a decrease in the probability of wet days in the Sahel region under anthropogenic forcing scenarios RCP4.5 and RCP8.5. The decrease in wet days is stronger in the far future and under the RCP8.5 scenario (up to -30%). The study also finds that the probability of consecutive dry days (lasting at least 7 days and 10 days) is expected to increase in the Western Sahel, the Central Sahel, and the Sudanian Area under both scenarios, with stronger increases in the RCP8.5 scenario. In contrast, the decrease is expected over the Guinea Coast, with the changes more important under the RCP4.5. These changes in dry- and wet-spell probabilities are important for water management decisions and risk reduction in the energy and agricultural sectors. The study also highlights the need for decision-makers to implement mitigation and adaptation policies to minimize the adverse effects of climate change.

The dry washing method is an alternative to replace water washing, thereby reducing the negative impacts of contamination. However, commercial adsorbents come from industrial processes that, due to their composition, may not be such a sustainable resource in the global biodiesel production process. In this study, the use of organic residues, such as sawdust, coconut fiber, nutshell, rice husk and water hyacinth fiber, were proposed as bioadsorbents for the purification of biodiesel from waste cooking oil (WCO). Quality parameters such as the acid value, water content, and free and total glycerin content were evaluated and compared with those of commercial resins such as Magnesol® and Amberlite™. Promising results were obtained using sawdust during the purification process, achieving a 31.6% reduction in the acid value compared to that of unpurified biodiesel, the reduction was 31.3% more efficient than Amberlite™. Sawdust adsorbed free glycerin at 55.8%, being more efficient than Amberlite™. The total glycerin values were similar between commercial resins and sawdust. A water content values were similar than Amberlite™ and better than that with Magnesol®, at 4.3% and 39.81%, respectively. These results show that sawdust can be used as an alternative bioadsorbent in a dry purification method for biodiesel being a residue with less environmental impact.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

A new sulbatamol sulphate SBS membrane electrode was prepared that utilizing for its determination ; depend on the forming of the association complex ion of sulbatamol sulphate by the phosphotungstate counter anion deposed in poly vinyl chloride PVC polymer, by use a (Di-n- Octyl Phenyl Phthalate)(Dopp) as the plastizier substance, in membrane.The features properties as well as the behavior of it .The new electrode have been elaborated. The concentrations of medicine by utillizing This sensor show a fast, stable, near-Nernstian response in the range (1x10^-1-1x10^-6) mol/ L were determined with correlation coefficient of about (r = 0.9991) and with of a relative standard about 0.416 additionally deviation relative standard error of 1.710 %.^pot The nernast linearity slop was founded and it is equal to 28.9 mV/decade and the detection limit was 4.1 x 10^-6 mol/ L.The electrode selectivity coefficient K_i,j was calculated, in the existence of several interferences cations with confirmed medicine solutions. It was found the pH range response is in the range of (3 -7), with the response time of (30 – 116) sec. for various concentrations at room temperture , the lifetime for electrode was found to be more than 21 days. The electrode was successfully used for potentiometric limitation of sulbatamol sulphate in several pharmaceutical drugs by using direct potentiometry.

Molybdenum oxides is well-known electro-catalysts in fuel cells systems, they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of Mo as catalysts in the pharmaceutical analysis is not common yet. In this study, bare glassy carbon electrodes were modified by the oxides by means of electrochemical deposition and the modified electrodes were used as catalysts for the electrochemical oxidation of hydrochlorothiazide (HCT). Well-resolved anodic peaks were reported for the analyzed pharmaceuticals when the Mo/GCE was utilized for the analysis of HCT. Analytical performance of the modified electrodes was evaluated based on the following statistical parameters; linearity ranges, correlation coefficients, limits of detection and quantitation, and recovery values. The prepared electrodes were used for the determination of the active ingredients in their pharmaceutical formulations and the reported activity was correlated to influence of the utilized pH on both structures of the used electrodes and the detected analytes.

This study involved a comprehensive examination of sensory attributes in Bísaro dry-cured loins, including odor, androsterone, scatol, color, fat color, hardness, juiciness, chewiness, flavor intensity, and flavor persistence. Analysis of 40 samples revealed a wide variation in these attributes, ensuring a robust margin for multivariate calibration purposes. The respective near-infrared (NIR) spectra unveil distinct peaks associated with significant components such as protein, lipid, and water. Support Vector Regression (SVR) models were methodically calibrated for all sensory attributes, with optimal results using multiplicative scattering correction pre-treatment, MinMax normalization, and radial base kernel (non-linear SVR model). The predictive models exhibited acceptable results, characterized by R-squared values close to 1 (0.9616 - 0.9955) and low RMSE values (0.0400 – 0.1031). The prediction set's relative standard deviation (RSD) remained under 5%. Comparisons with prior research revealed significant improvements in prediction accuracy, particularly when considering attributes like pig aroma, hardness, fat color, and flavor intensity. This research underscores the potential of advanced analytical techniques to improve the precision of sensory evaluations in food quality assessment.

Accordingly, a lot of dry direct seeding rice would be dense planted, that the initial seedling quantity could approach or even exceed the targeted effective panicle number. While limit information is available to evaluate the effects of involved novel nitrogen application methods, that total nitrogen once applied at a determined leaf age stage, on the yield formation traits of such dense planted dry direct seeding rice. The two-year experiments with total 180 kg ha-1 nitrogen once applied time treatments at sixth (L6), seventh (L7), eighth (L8), ninth (L9) and tenth (L10) leaf age stages were carried out. Results showed that the above-ground dry matter weight at maturity and grain yield of L8 was 2.1% ~ 11.8% and 4.0% ~ 9.9% higher than those of other treatments. Compared to other treatments, the higher above-ground dry matter weight after heading stage, bigger mean leaf area index with higher leaf area index at heading stage, increased leaf area duration, crop growth rate and net assimilation rate from jointing to heading period were important traits of higher grain yield formation of L8. In addition, the L8 had relative higher grain-leaf ratio traits than other treatments. Overall, a total 180 kg ha-1 nitrogen with mixed urea and compound fertilizer once applied at eighth leaf age stage would be suggest a useful high yield cultivation method for dense planted dry direct seeding rice in rice-wheat rotation system.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavourable drugs properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use as inhalable formulations. Particulate-solid HA-VAN25 complex by spray drying from an aqueous dispersion was obtained. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern by X-ray was observed. The powder density, geometric size and morphology showed a suitable aerosolization and aerodynamic performance of the powder, indicating the capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 hours. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus, showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

Recently, the difficulties in recycling and environmental pollution caused by metal-based electrode materials have limited the further development of batteries. Therefore, biomass carbon materials, with their environmental friendliness and stable performance, are the key to solving this problem. Many advances have been achieved by researchers for the application of biomass porous carbon materials in batteries. Nevertheless, the same biomass carbon materials in batteries face problems such as low utilization, low yield, and a cumbersome preparation process. This paper thus aims to summarize the recent progress of biomass carbon materials in the field of batteries and provide a detailed description of the battery performance of biomass carbon materials from three perspectives: synthesis, structure and application of carbon materials. We believe that biomass carbon composites are in line with future development and have a broad application prospect. Finally, we will give our in-depth prospect on developing biomass carbon materials.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

Age-related macular degeneration (AMD) is a leading cause of irreversible blindness world-wide. We recently reported that polyethylene glycol (PEG) can activate the alternative pathway of the complement system and induce choroidal neovascularization (CNV) in mice. Currently, no other investigator has demonstrated CNV after PEG injection in the mouse eye. The aim of this article is twofold: we review the histologic changes in mouse retina and retinal pigmented epithelium (RPE) after treatment with PEG, and we summarize a model of wet and dry AMD pathogenesis in mice through subretinal PEG treatment of RPE cells and retinal layers. We injected (subretinal) male C57BL/6 mice with 2 μL of solution containing 0.5 mg and 1.0 mg of PEG or PBS in control groups. Eyes were harvested at day 1, 3 and 5 after injection and processed for analysis. Sections were immunohistochemically stained for complement component C3, mem-brane attack complex (MAC), and cytokeratin 18. Light and laser confocal microscopy was used for image capturing. PEG increased deposition of C3 and MAC on RPE cells and on all retinal layers after 1.0 mg injection. PEG induced loss of cellular contacts between RPE cells and migration of RPE cells in the subretinal space at day 1 after PEG injection. After 0.5 mg PEG injection, increased size of RPE cells was detected at day 3 and 5. Apoptotic bodies were observed in outer nuclear layer at day 3 and 5 after 0.5 mg PEG treatment. RPE cells with dark cytoplasm and condensed chromatin were observed. Higher doses of PEG induce CNV, encouraged RPE cell proliferation and death, and damage photoreceptors in mice. This simple and fast model may be useful to explore the pathogenesis of both dry and wet AMD.

The basis of the work of electroencephalography (EEG) is the registration of electrical impulses from the brain or some of its individual areas using a special sensor/electrode. This method is used for the treatment and diagnosis of various diseases. The use of wet electrodes in this case does not seem viable, for several well-known reasons. As a result of this, a detailed analysis of modern EEG sensors developed over the past few years is carried out, which will allow researchers to choose this type of sensor more carefully and, as a result, conduct their research more competently. Due to the absence of any standards in the production and testing of dry EEG sensors, the main moment of this manuscript is a detailed description of the necessary steps for testing a dry electrode, which will allow researchers to maximize the potential of the sensor in the various type of research.

Electrophysiological mapping (EM) using acute electrode probes is a common procedure performed during functional neurosurgery. Due to their constructive specificities, the EM probes are lagging in innovative enhancements. This work addressed complementing a clinically employed EM probe with carbonic and circumferentially segmented macrocontacts that are operable both for neurophysiological sensing ("recording") of local field potentials (LFP), and for test stimulation. The paper illustrates in-depth the development, that is based on direct writing of functional materials. The unconventional fabrication processes were optimized on planar geometry and then transferred to the cylindrically thin probe body. We report and discuss on the constructive concept and architecture of the probe, characteristics of the electrochemical interface deduced from voltammetry and chronopotentiometry, and the results of in vitro and in vivo recording and pulse stimulation tests. Two and three directional macrocontacts were added on probes having shanks of 550 and 770 m diameters and 10-23 cm lengths. The graphitic material presents a ~2.7 V-wide, almost symmetric water electrolysis window, and an ultra-capacitive charge transfer. When tested with 150 s biphasic current pulses, the interfacial polarization stayed safely away from the water window for pulse amplitudes up to 9 mA (135 C/cm2). The in vivo experiments on adult rat models confirmed the high-quality sensing of LFPs. Additionally, the in vivo-prevailing increase of the electrode impedance and overpotential are discussed and modeled by an ionic mobility-reducing spongiform structure; this restricted diffusion model gives new applicative insight into the in vivo-uprisen stimulation overpotential.

One of the significant challenges today in the brain-machine interface using invasive methods is the stability of the chronic record. In recent years, polymer-based electrodes have gained notoriety for achieving mechanical strength values close to that of brain tissue, promoting a lower immune response to the implant. In this work, we fabricated fully polymeric electrodes based on PEDOT:PSS for neural recording in Wistar rats. We characterized the electrical properties and both in-vitro and in-vivo functionality of the electrodes. Also, we employed histological processing and microscopical visualization to evaluate tecidual immune response in 7, 14, and 21 days post-implant days. Electrodes with 400-micrometer channels showed a 12dB signal-to-noise ratio. Local field potentials were characterized under two conditions: anesthetized and free-moving. There was a proliferation of microglia to the tissue-electrode interface in the first days, with a decrease after 14 days. Astrocytes also migrated to the interface, but there was no continuous recruitment of these cells in the tissue, showing inflammatory stability at 21 days. The signal was not affected by this inflammatory action, demonstrating that fully polymeric electrodes can be an alternative to prolong the valuable time of neural recordings.

In this study the processes taking place on the surfaces of nanostructurized Cu/CuO and Cu/CuO/Pd electrodes at different potential, $E$, values in the solutions of 0.1 M KOH in H$_2$O and D$_2$O (heavy water) were probed by the surface enhanced Raman spectroscopy (SERS) and analysis of electrochemical reactions occurring under experimental conditions is presented. Bands of the SERS spectra of Cu/CuO/Pd electrode observed in the range of $E$ values from +0.3~V to 0 V~(SHE) at 1328 - 1569~cm$^{-1}$ are consistent with the existence of species which are adsorbed or weakly bound to the surface with the energy of interaction close to 15 - 21~kJ mol$^{-1}$. These bands can be attributed to the ad(ab)sorbed (H$_3$O$^+$)$\rm{_{ad}}$, (H$_2^+$)$\rm{_{ab}}$ and (H$_2^+$)$\rm{_{ad}}$ ions as intermediates in reversible HER/HOR processes taking place on Cu/CuO/Pd electrode. There was no isotopic effect observed; this is consistent with a dipole nature of electron-ion pair formation of adsorbed (H$_3$O$^+$)$\rm{_{ad}}$ and (H$_2^+$)$\rm{_{ad}}$ or (D$_3$O$^+$)$\rm{_{ad}}$ and (D$_2^+$)$\rm{_{ad}}$. In accordance with literature data SERS bands at 125-146~cm$^{-1}$ and $\sim 520-565$~cm$^{-1}$ were assigned to Cu(I) and Cu(II) oxygen species. These findings corroborate the mechanism of cascading reduction of water.

This review provides informations and details for the fabrication of biosensors that are composed from lipid membranes and have been utilized and applied to rapidly detect food toxic compounds, environmental pollutants and analytes of clinical interest. Biosensors based on polymeric lipid membranes have been used to rapidly detect a wide range of these analytes and offer several advantages such as fast response, high sensitivity and selectivity, can be portable for in the field applications, and small size. A description of the construction of these devices and their applications for the rapid detection of food toxic substance, environmental pollutants and analytes of clinical interest is provided in this review.

This study was conducted to determine the effect of different types of olive cake (five treatments) in the diet of Bísaro pigs on the volatile compounds and sensory characteristics in the dry-cured loin and dry-cured “cachaço” (2 processed meat products). The treatments applied are based on the type of extraction and this may imply differences in their water and fat content. Eighty com-pounds were identified, and grouped into eight chemical classes: hydrocarbons, aldehydes, es-ters, alcohols, ketones, acids, furans, and other compounds. Aldehydes and alcohols were the ma-jor groups of compounds, representing 57.06-66.07 % and 68.67-75.61 % for the loin and “cacha-ço”, respectively. There were no significant differences between treatments for any of the volatile compounds identified. The major aldehydes were hexanal, heptanal, pentanal, and propanal. These compounds were significantly higher (p<0.001) in “cachaço”. This significant difference be-tween the two types of dry-cured products is directly related to the amount of total fat content. The major alcohols were 2.3-butanediol, 1-octen-3-ol, 1-butanol, 3-methyl, 1-hexanol, benzyl-alcohol and glycidol. Except for compounds 2,3-butanediol and benzyl-alcohol, the majority in this group are significantly different in terms of the type of dry-cured product. As for the sensory evaluation, for both dry-cured products, the trained tasters did not detect significant differences between the different treatments, which is in line with the results obtained for volatile compounds.

Roller milling of sorghum and quinoa seeds into flour fractions (course, middle, and fine) was investigated, chemically analysed and applied in the baking of gluten-free sourdough bread. Gap settings were adjusted to 0, 5, 8 and 10 for quinoa and 3, 5, and 7 for sorghum. The fine fractions reached values of up to about 41% (gap 8) for quinoa and around 20% for sorghum (gap 5). SEM pictographs illustrated clear separation of each fraction with chemical analysis showing high contents of protein, TDF (total dietary fibre) and IDF (insoluble dietary fibre) in the course fraction. Up to 77% starch content was obtained in the fine fraction with significant amounts of SDF (soluble dietary fibre) which has good health benefits. Increasing the dough moisture up to 90% helped in decreasing the bread crumb firmness, while low Avrami parameters and RVA pasting behaviour indicated slow bread staling rate for both sourdough breads.

The development of smart negative electrode materials with high capacitance for use in supercapacitors remains challenging. Although there have been several types of electrode materials with high capacitance used in energy storage, carbon-based materials are the most reliable electrodes due to their high conductivity, high power density and excellent stability. The most common complaint about general carbon materials is that these as-formed electrode materials can hardly ever be used as free-standing electrodes. Free-standing carbon-based electrodes are in high demand and are a passionate topic of energy storage research. Electrospun nanofibers are a potential candidate to fill this gap. However, the as-spun carbon nanofibers (ECNFs) have low capacitance and energy density on their own. To this end, several attempts have been made to improve these characteristics. In this review, we introduce negative electrode materials that have been developed. Moreover, this review places special attention to the advances of electrospun nanofiber-based negative electrode materials and their limitations. Based on the above information, we put forth a future perspective on how these limitations can be overcome to meet the demands of next-generation smart devices.

Non-standard diesel blends can be harmful to the environment and human health. In this context, a simple analytical method to estimate the biodiesel mixture ratio in diesel was developed based on the impedance spectroscopy (IS) associated with the interdigitated sensors. In this article, four different interdigitated sensors, variable comb spacing (G), were simulated using the COMSOL Multiphysics software. Based on finite element simulations, four interdigitated electrode architectures by manufactured and evaluated. According to the X-ray powder diffraction technique, the deposition of the conductive layer (Au°) over the surface of the dielectric substrate (SiO2) did not alter its phase composition. In the analysis of AFM and SEM, it was possible to observe irregular edges on the electrodes, possibly related to thin layers' manufacturing process and mechanical stability. Another characteristic observed in the AFM images was the height of the step of the gold layer of the sensor. Several cross-sections were obtained, and the mean step value is 225.71 ± 0.0032 nm. Although there are differences in the roughness, the whole sensor has nanometric roughness. Based on the finite element method simulation performed, it can be assumed that the geometric parameters more suitable for the manufacturing of the electrode are: W = 20 µm, L = 1000 µm, G = 50 µm e N = 40 digits. The electrical characterization performed by impedance spectroscopy showed that we could differentiate between biodiesel and diesel fuels and their pseudo-binary mixtures in the low-frequency region.

The aims of this work were to examine the new electrode, based on polymer bacteria modified aluminum electrode for simultaneous production of electricity and degradation of phenol. This electrode is based aluminum modified by bacteria inserted in the polymer matrix, developed in situ on the surface. This electrode, designated subsequently by bacteria-polymer-aluminum, Showed stable response and was characterized with voltametric methods, as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The experimental results revealed that the prepared electrode could be a feasible for degradation of hazardous phenol pollutants. The sensor was successfully applied to the determination of phenol in a real sample with satisfactory results.

Dry eye disease (DED) is a multifactorial disorder in which tear fluid homeostasis is lost, resulting in increased tear film osmolarity and ocular surface irritation. In Asia, the short tear film breakup time type-DED is common, and stabilization of the tear film is the first goal of treatment. Treatment of DED begins with eye drops. Until now, artificial tears and steroid eye drops have been the main treatment for DED. However, artificial tears require frequent administration of eye drops and thus pose adherence problems, while steroids have problems with side effects (cataracts, increased intraocular pressure). This review evaluates the new generation of DED therapies in Asia based on what is known about them and demonstrates that they are more effective for DED than traditional therapies such as artificial tears and steroids. Based on these considerations, it is proposed that the optimal treatment for DED in Asia is the initial application of mucin secretion enhancing eye drops (long-acting diquafosol) and oral supplements, and if additional treatment is needed, cyclosporine eye drops and the adjunctive therapies presented in this review are added.

Ultrasound is a well-known tool to produce thermal and non-thermal effects on cells and tissues. These effects require a correct application of ultrasound in terms of localization and acoustic energy delivered. This article describes a new device that combines ultrasound and Dry Needling treatments. The ultrasound transducer can rotate in 3D space mechanically to align itself in the direction of the needle. The transducer electronically focuses the acoustic pressure automatically on the needle tip and its surroundings. A computer, using graphical interface software, controls the angulation of the array and the focus position.

Background: Aflatoxins (AFs) as toxic compounds are widely spread. They are frequent contaminants of crops that are produced by fungi species. Corn is of crops that widely used in the corn dry milling process; a four-step procedure comprises grain handling and milling, liquefaction and saccharification, fermentation, and co-product recovery that produces ethanol and animal feed. However, it is possible that corn as a feed for dry milling process might be contaminated with AFs. Therefore, monitoring AFs in during widespread this process results having a better understanding of the fate of AFs. Methods: In this study, a sample of corn kernel was contaminated with a high level of AFs using Aspergillus parasiticus. Then, the corn flour comprising 23400.5 µg/kg of the total level of aflatoxins (AFT), was hydrolyzed by enzymes and acid for ethanol fermentation with Saccharomyces cerevisiae. Also, the level of AFs was monitored during ethanol fermentation process. Results: The results showed that AFs did not detect in the ethanol produced through fermentation and it was safe. Also, during the experiments, the AFT level reduced by 58.5 and 95.7% for the ethanol fermentation with simultaneous saccharification and fermentation and ethanol production with acidic hydrolysis, respectively. Conclusion: The results of this study showed that highly contaminated corn with AFs can be used for ethanol fermentation through dry milling process and the produced ethanol was safe.

Each year in March, adherents of the Bahá’í faith abstain from eating and drinking from sunrise to sunset for 19 days. Thus, Bahá’í fasting (BF) can be considered as a form of daytime dry fasting. We tested if BF decreases energy expenditure after a meal and improves anthropometric measures, and systemic and tissue-level metabolic parameters. This was a self-controlled cohort study with 11 healthy men. We measured anthropometric parameters, metabolic markers in venous blood, and pre- and postprandial energy metabolism at systemic (indirect calorimetry) and tissue (adipose tissue and skeletal muscle microdialysis) level, both before and during BF. During BF, we found reduced body weight, body mass index, body fat and blood glucose. Postprandial increase in energy expenditure was lower, diet-induced thermogenesis tended to be lower. In adipose tissue, perfusion, glucose supply and lipolysis were increased. In skeletal muscle, tissue perfusion did not change. Glucose supply and lipolysis were decreased. Glucose oxidation was increased, indicating an improved insulin sensitivity. BF may be a promising approach to losing weight and improving metabolism and health. However, outside the context of religiously-motivated fasting, skipping a meal rather in the evening (dinner cancelling) might be recommended, as metabolism appears to be reduced in the evening.

The interest in dry EEG electrodes has increased in recent years and especially as everyday suitability earplugs for measuring drowsiness or focus of auditory attention. However, the challenge is still the need for a good electrode material, which is reliable and can be easily processed for highly personalized applications. Laser processing as used here is a fast and very precise method to produce personalized electrode configurations that meet the high requirements of in-ear EEG electrodes, for example. The arrangement of the electrodes on the very flexible and compressible mats allows an exact alignment of the electrodes to the ear mold and contributes to a high wearing comfort, as no edges or metal protrusions are present. For better transmission properties, an adapted coating process for surface enlargement of platinum electrodes is used, which allows easy control of the thickness and growth form of the porous layer. The porous platinum-copper alloy is chemically very stable, shows no exposed copper residues and enlarges the effective surface area by 40. In a proof-of-principle experiment, these porous platinum electrodes could be used to measure the Berger effect in a dry state using just one ear of a test person. Their signal-to-noise ration and frequency transfer function is comparable to gel-based silver/silver chloride electrodes.

(1)Background: Early-age concrete shrinkage induces stress that impact the cost and service life of concrete pavements. (2)Methods: In this study, strain measurements of field slabs were conducted and a methodology was presented that independently derived autogenous, drying, and thermal shrinkages in the initial stages of concrete placement. Total strain was measured according to five different environmental conditions and shrinkage strain was calculated for each condition. (3)Results: By measuring the strain of the slab and the specimen, the drying shrinkage strain was measured to be approximately 54% better than that by the conventional non-stressed cylinder method because it was possible to measure the drying shrinkage strain at the surface rather than in the middle part of the slab along its depth direction. When the water-to-cement ratio increased (35→40%), there was a considerable reduction (317με→82με) of autogenous shrinkage strain for the concrete at 28 days of age. Furthermore, calculation of stress-dependent strain allowed the presentation of more intuitive and accurate results. (4)Conclusion: As the measurement of independent shrinkage occurrence is possible, the consequent calculated result of the stress-dependent strain acting on real slabs will facilitate improvement in the construction quality, reduction in the development of defects in the concrete structure, and increase in the service life.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

Traditional dry fermented meat products are obtained artisanally in many countries, where they represent a gastronomic heritage well distinguished from industrial counterparts. This food category is most often obtained from red meat, a food commodity that is under attack because of evidences of increased risk of cancer and degenerative diseases with high consumption. However, traditional fermented meat products are intended for moderate consumption and gastronomic experience and, as such, their production must be continued also to safeguard culture and economy of the geographical areas of origin. In this review, the main risks attributed to these products are considered and how these risks are minimized by following precise production norms, respectful of the ancient manufacturing processes is described. Moreover, results obtained in studies reporting use of autochthonous microbial cultures of lactic acid bacteria (LAB), coagulase negative staphylococci (CNS), Debaryomyces hansenii and Penicillium nalgiovense to improve safety and quality of traditional fermented meats are summarized. The role of these products as a source of microorganisms that can be beneficial to the host are also considered. From the results of the studies reviewed here it appears that the development of autochthonous cultures for these foods ensure safety and stabilize sensory characteristics with possibility to be extended to the large variety of traditional productions.

Data on the seasonally dry tropical forests of Mexico have been examined in the light of statistical mechanics. The results suggest a division into two classes of species. There are drifting populations of a cosmopolitan class capable of existing in most dry forest sites; these have a statistical distribution previously only observed (globally) for populations of alien species. A high proportion of species found only at a single site are endemic and these prefer sites comparatively low in species richness.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

In this work we successfully prepared a modified cobalt oxide (Co3O4) carbon paste electrode to detect Levofloxacin (LEV). By synthesizing Co3O4 nanoparticles through the chemical coprecipitation method, the electrochemical properties of the electrode and LEV were thoroughly investigated using CV, SWV, EIS, while material properties were scrutinized using ICP-OES, TEM, SEM, and XRD. The results showed that the prepared electrode displayed a better electrocatalytic response than the bare carbon paste electrode. After optimizing SWV, the electrode exhibited a wide linear working range from 1 to 85 μM at pH 5 of BRBS as the supporting electrolyte. The selectivity of the proposed method was satisfactory, with good repeatability and reproducibility, strongly suggesting a potential application for determining LEV in real samples, particularly in pharmaceutical formulations. The practicality of the approach was demonstrated through good recoveries, and the morphology of the materials was found to be closely related to other parameters, indicating that the developed method can provide a cost-effective, rapid, selective, and sensitive means for LEV monitoring. Overall, this project has made significant progress towards developing a reliable method for detecting LEV and has opened up new opportunities for future research in this field.

In this study, the preparation of the composite 3% Au/graphite-C3N4 (3% Au/g-C3N4) sensing material was prepared by doping 3% Au onto the surface of graphitic carbonitride (C3N4) for detection pimobendan. By the way of sensing materials characterization, the X-ray diffraction analysis (XRD) and transmission electron Microscope (TEM) were performed. The cyclic voltammetry (CV) was used to measure the concentration and redox properties of pimobendan. It can be seen that when the voltage value is 0.05 V, and a reduction peak was appeared and the pimobendan concentration (0 to 55 μM) has a relationship with the reduction current value. At low concentrations of pimobendan concentration from 0.0 to 0.8 μM, the linearity R2 = 0.9642 with a detection limit of 0.28 μM. A possible pimobendan sensing mechanism on 3% Au/g-C3N4 was proposed.

The present review article concludes with three different types of materials recently used to enhance the efficiency of supercapacitors. The first type involves carbon-based materials for storage and supercapacitor applications. The carbon materials could be obtained naturally and synthesized manually based on the needs. The second type discusses the recent advances in metal oxide materials for high-performance supercapacitors. The metal oxide materials involve in different types of attachment through the bi-tri metallic bonding, which enhances the specific capacitance. The third type involves recently advanced materials for high energy and power density application. The power and energy density of the materials is enhanced by the surface modification of the materials. In recent days, the MXene and Nano-composite materials seems to be an appropriate material to increase the power and energy density of the device.

Population growth and increasing global demand for freshwater have raised a serious challenge for the depleting sources of freshwater in the 21st century. Desalination technologies can be a reliable technique for providing freshwater. Capacitive deionization is one of the innovative desalination methods that has received increasing interest. Flow-electrode capacitive deionization (FCDI) (a new architecture of capacitive deionization) is one of the efficient, cost-effective, and environmentally-friendly desalination methods for freshwater production. In this experimental research, the performance of an FCDI system was investigated and the influence of important parameters such as flow rate of flow-electrodes, electrolyte salt concentration of flow-electrodes, and initial feed water concentration will be assessed on the efficiency of desalination operation. In this study, the flow-electrodes operated in short-circuited closed-cycle operation (SCC) mode, and also the feed water operated similarly to the flow-electrodes in closed-cycle. Moreover, in all the experiments, the salt adsorption capacity (SAC) and salt removal efficiency (SRE) was calculated. Herein, by optimizing the above mentioned parameters, the salt removal efficiency of 83% and a SAC value of 29.12 mg/g dry carbon were achieved in 5 hours.

Laser reduced graphene oxide (LRGO) on a PET substrate was prepared in one-step to obtain the LRGO grid electrode for sensitive carbaryl determination. The grid form results in a grid distribution of different electrochemically active zones affecting the electroactive substance diffusion towards to the electrode surface and increasing the electrochemical sensitivity for carbaryl determination. Carbaryl is electrochemically irreversibly oxidized by the secondary amine moiety of the molecule with the loss of one proton and one electron in the pH range from 5 to 7 by LSV on the LRGO grid electrode with a scan rate of 300 mV/s. Some interference of the juice matrix molecules did not significantly affect the LSV oxidation current of carbaryl on the LRGO grid electrode after adsorptive accumulation without applied potential. The LRGO grid electrode can be used for LSV determination of carbaryl in fruit juices in the concentration range from 0.25 to 128 mg/L with LOD of 0.1 mg/L by. The fabrication of the LRGO grid electrode opens up possibilities for further inexpensive monitoring of carbaryl in other fruit juices and fruits.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

With the application of high-precision, enormous rotating equipment and the addition of harsh working conditions, the advantages of dry gas sealing technology are increasingly obvious. Herein, research on the dynamic stability of dry gas seals is reviewed based on their operating mechanism. The influence of the dry gas seal structure, vibration response, and dynamic followability on the reliability of the shaft end sealing system of rotating machinery is the focus of current dry gas sealing technology. This work reviews the research history; analyzes the key coefficient of instability of the sealing system under external disturbances and the existing research on stability models; discusses the influence of starting and stopping characteristics, working conditions, and groove parameters on the stability of dry gas seals; and points out the shortcomings in the existing research. In addition, potential developments in dynamic stability are proposed, including improving model accuracy, improving experimental techniques, or applying intelligent control and optimization methods to enhance the dynamic stability of the sealing system. Finally, the development prospects for dry gas sealing technology in intelligent monitoring and wide temperature range adaptations are discussed, and theoretical guidance for improving the dry gas seal system is provided.

A simple fabrication method in the surface modification of electroosmotic silicon microchannel using thermal dry oxidation is presented. The surface modification is done by coating the silicon surface with a silicon dioxide (SiO₂) layer using thermal oxidation process. The process is aimed not only to improve the surface quality of the channel to be suitable for electroosmotic fluid transport but also to reduce the channel width using a simple technique. Initially, the parallel microchannel array with dimensions of 0.5 mm length and width ranging from 1.8 µm to 2 µm are created using plasma etching on the 2x2 cm <100> silicon substrate. The oxidation of silicon channel in a thermal chamber is then conducted to create the SiO₂ layer. The layer properties and the quality of the surface are analyzed using SEM and surface profiler, respectively. The results show that the maximum oxidation growth rate occurs in the first 4 hours of oxidation time and the rate decreases by time as the oxide layer becomes thicker. It is also found that the surface roughness is reduced with the increase of process temperature and oxide thickness. The scallop effect on the vertical wall due to plasma etching process also improved with the presence of the oxide layer. After the oxidation, the channel width is reduced by ~40%. The demonstrated method is suggested for the fabrication of a uniform channel cross section with high aspect ratio in sub-micro and nanometer scale that will be useful for the electroosmotic flow (EOF) manipulation of the biomedical fluid sample.

Due to its time effective, joint friendly and highly customizable character whole-body-electromyostimulation (WB-EMS) is regarded as a feasible solution for a large variety of training issues particularly in the area of non-athletic application. To identify gaps in research and summarize prevalent evidence we conducted an evidence map on outcomes addressed by WB-EMS trials in middle-aged to older, non-athletic adults. Based on a comprehensive systematic search in five databases and two study registers according to PRISMA, 54 projects published in 80 articles were included. More than 90% of the studies reported outcomes related to the physical fitness or function domain. Body composition parameters were addressed by two thirds of the projects. Health-related outcomes addressed by WB-EMS included cancer/neoplasm (n=7), endocrine regulation (n=8), glucose metabolism (15), nervous system diseases (n=2), cardiovascular system diseases (n=22), non-specific chronic low back pain (n=4), osteopenia (n=5) and diseases of the renal system (n=12). Outcomes related to inflammation were addressed 18 times. Of importance, no studies reported clinically relevant adverse effects related to the WB-EMS intervention. In summary, while considerable evidence on outcomes related to fitness/function and body composition is prevalent, evidence gaps of WB-EMS research were particular evident for diseases of the nervous and cerebrovascular system.

The utilization of dual-potential mode of integrated array (IDA) electrodes and other two-electrode systems has revolutionized electrochemical detection by enabling the simultaneous and independent detection of two species, accompanied by the exhibition of unique characteristics. In contrast to conventional dual-potential electrodes, the rotating ring disk electrodes (RRDE), IDA electrodes demonstrate analogous yet vastly improved performance metrics, characterized by remarkable collection efficiency and sensitivity. Notably, due to the distinctive microscale structure of IDA electrode, the special “feedback” effect makes IDA a unique signal amplifier. In recent decades, the research surrounding IDA electrodes has garnered escalating interest due to their attractive attributes. This review centers its focus on the fabrication and applications of IDA electrodes. In the realm of fabrication, two critical breakthroughs are poised for realization: the achievement of reduced dimensions and the diversification of materials. Established fabrication methods for IDA electrodes encompass photolithography, inkjet printing, and direct laser writing, each affording distinct advantages in terms of size and precision in IDA construction. Predominantly employed materials for IDA electrodes include gold, platinum, and carbon, with the selection of fabrication methods guided by considerations such as material properties, desired dimensions, cost-efficiency, and specific application requisites. Within the domain of applications, IDA electrodes, capitalizing on their distinctive attributes, have found utility in diverse fields. This review summarizes the applications of IDA electrodes based on their fundamental working principles, encompassing redox cycling, resistance modulation, capacitance variations, and more. The potential for further development of this specialized tool to exhibit enhanced properties holds substantial promise.

The inhibition of localised corrosion is known to involve multiple processes taking place over a range of time and length scales that are difficult to study by conventional electrochemical methods. This work demonstrates an approach to probing complex localised electrochemical processes by combining an electrochemically integrated multi-electrode array (also known as wire beam electrode (WBE)), scanning vibrating electrode technique, scanning electrochemical microscopy and surface analytical techniques. Each technique reveals certain aspects of the dynamically changing, multi-scale, inhibitor-microstructure interactions and local chemistry over a heterogeneous AA2024-T3 alloy surface in the presence of an environmentally friendly inhibitor; cerium diphenyl phosphate (Ce(dpp)3).

The DEP force is usually calculated from the object’s point of view using the interaction of the object’s induced dipole moment with the inducing field. Recently, we described the DEP behavior of high- and low-conductive 200-µm 2D spheres in a square 1x1mm chamber with a plane-versus-plane electrode configuration from the system’s point of view. Here we extend our previous considerations to the plane-versus-plane and pointed-versus-pointed electrode configurations. The trajectories of the sphere center and the corresponding DEP forces were calculated from the gradient of the system’s overall energy dissipation for given starting points. The dissipation’s dependence on the sphere’s position in the chamber is described by the numerical “conductance field”, which is the DC equivalent of the capacitive charge-work field. While the plane-versus-plane electrode configuration is field-gradient free without an object, the presence of the highly or low-conductive spheres generates structures in the conductance fields, which result in very similar DEP trajectories. For both electrode configurations, the model describes trajectories with multiple endpoints, watersheds, and saddle points, very high attractive and repulsive forces in front of pointed electrodes, and the effect of mirror charges. Because the model accounts for inhomogeneous polarization within the objects, the approach allows the modeling of the complicated interplay of attractive and repulsive forces near electrode surfaces and chamber edges. Non-reversible DEP forces or asymmetric magnitudes for the highly and low-conductive spheres in large areas of the chamber indicate the presence of higher-order moments, mirror charges, etc.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

This study aimed to develop a high-quality dry emulsion incorporating omega-3, 6, and 9 fatty acid-rich ostrich oil for use as a dietary supplement. Extracted from abdominal adipose tissues using a low-temperature wet rendering method, the ostrich oil exhibited antioxidant properties, favorable physicochemical properties, microbial counts, heavy metal levels, and fatty acid compositions, positioning it as a suitable candidate for an oil-in-water emulsion and subsequent formulation as a dry emulsion. Lecithin was employed as the emulsifier due to its safety and health benefits. The resulting emulsion, comprising 10% w/w lecithin and 10% w/w ostrich oil, was stable, with a droplet size of 3.93 ± 0.11 μm. This liquid emulsion underwent transformation into a dry emulsion to preserve the physicochemical stability of ostrich oil, utilizing Avicel® PH-101 or Aerosil® 200 through a granulation process. Although Aerosil® 200 exhibited superior adsorption, Avicel® PH-101 granules surpassed it in releasing the ostrich oil emulsion. Consequently, Avicel® PH-101 was selected as the preferred adsorbent for formulating the ostrich oil dry emulsion. The dry emulsion, encapsulated with a disintegration time of 3.11 ± 0.14 min for ease of swallowing, maintained microbial loads and heavy metal contents within acceptable limits. Presented as granules containing butylated hydroxytoluene, the dry emulsion showcased robust temperature stability, suggesting the potential incorporation of animal fat into dry emulsions as a promising dietary supplement.

This study aimed to develop a high-quality dry emulsion incorporating omega-3, 6, and 9 fatty acid-rich ostrich oil for use as a dietary supplement. Extracted from abdominal adipose tissues using a low-temperature wet rendering method, the ostrich oil exhibited antioxidant properties, favorable physicochemical properties, microbial counts, heavy metal levels, and fatty acid compositions, positioning it as a suitable candidate for an oil-in-water emulsion and subsequent formulation as a dry emulsion. Lecithin was employed as the emulsifier due to its safety and health benefits. The resulting emulsion, comprising 10% w/w lecithin and 10% w/w ostrich oil, was stable, with a droplet size of 3.93 ± 0.11 μm. This liquid emulsion underwent transformation into a dry emulsion to preserve the physicochemical stability of ostrich oil, utilizing Avicel® PH-101 or Aerosil® 200 through a granulation process. Although Aerosil® 200 exhibited superior adsorption, Avicel® PH-101 granules surpassed it in releasing the ostrich oil emulsion. Consequently, Avicel® PH-101 was selected as the preferred adsorbent for formulating the ostrich oil dry emulsion. The dry emulsion, encapsulated with a disintegration time of 3.11 ± 0.14 min for ease of swallowing, maintained microbial loads and heavy metal contents within acceptable limits. Presented as granules containing butylated hydroxytoluene, the dry emulsion showcased robust temperature stability, suggesting the potential incorporation of animal fat into dry emulsions as a promising dietary supplement.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

: The objective of this study was to obtain different dry matter contents and proportions of mel-on plant biomass for silage making. A completely randomized design was adopted with a facto-rial scheme (3 x 2) in four replications. The first factor corresponded to three mixtures of melon biomass on as fed basis (AF) of plant (branch + leaf) and fruit (harvested melon) as follows: 100% plant, 90% plant + 10% fruit, and 100% fruit. The other factor corresponded to the ensiled materi-al with fresh and dehydrated melon plant biomass (40% DM) which was dried in the field, after harvest. Silages with partial dehydration of the biomass available after fruit harvest with 0% and 10% fruit showed the greatest DM values: 297 and 293 g/kg DM, respectively. Silages with 0, 100 and 10% fruit showed medium LAB populations: 5.79, 5.14 and 4.58 logs CFU/g, respectively. Higher concentrations of acetic acid contents were observed in silages with 0 and 10% fresh fruit, which were 14.9 and 14.1 g/kg DM, respectively. Silages with 0% and 100% of dehydrated fruit showed better results for the indicators of good-quality silage. Dehydration improves the fer-mentative profile and quality of the melon silage.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 0.4 − 1 μm holes in alumina Al2O3 etch masks with 20-50 nm thickness. Such dielectric masks simplify fabrication of photonic crystal (PhC) light trapping patterns for the above-Lambertian performance of high efficiency solar cells. Conditions of laser ablation of transparent etch masks and effects sub-surface Si modifications were revealed by plasma etch- ing, numerical modeling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs-laser direct writing for dry plasma etch of Si.

The alteration of the delicate balance that regulates the secretion and distribution of the tear film determines the dry eye (DE) syndrome, because the tear film represents the interface between the eye and the environment. Despite having a multifactorial origin, the main risk factors for the emergence of the ocular disease are female gender and advanced age. Likewise, morphological changes in several glands and in chemical composition of their secretions such as proteins, mucins, lipidics, aqueous tears, and salinity, are highly relevant factors to maintain a condition of good health of the ocular anterior segment. Another key factor of recurrence and onset of the disease is the presence of local and/or systemic infiammation that reflex on the ocular surface. However, it is one of the most commonly encountered disease in clinical practice and many other causes related to daily life and to lengthen the average life will contribute to the beginning. This review will consider how and what disorders of the ocular surface are responsible for a widespread pathology so. In the end, the most appropriate and new therapies will be briefly exposed according to the specific pathology.

This study aimed to evaluate the influence of olive cake on the diet of autochthonous Bísaro pigs in processed products. To this purpose, loins and “cachaços” were used and subjected to a manufacturing flowchart to obtain a dry-cured product. Both products were subjected to the same formulation, ingredients, and curing steps. Regarding the physicochemical composition, there were significant differences between the two products for the parameters of aw (p&lt;0.001), moisture (p&lt;0.001), total fat (p&lt;0.001), protein (p&lt;0.001), and haem pigments (p&lt;0.001). As for the diet, it only significantly influences the NaCl content (p&lt;0.05). Neither the product nor the diet had any influence (p&gt;0.05) on the fraction of saturated fatty acid (SFA), monounsaturated fatty acid (MUFA), and polyunsaturated fatty acids (PUFA). However, there is a significant difference when it comes to omega 3 (p&lt;0.05). These fatty acids increased with the addition of olive cake, and the diet with olive cake centrifuged by 25% had the highest value for both products. The increase in this omega 3 resulted in a decrease in the PUFA n-6/n-3 ratio (p&lt;0.01) in the diets with olive cake, compared to the control diets.

Screen-printed carbon electrode (SPCE) is a useful technique that has been widely used in the practical application of biosensors oriented to point-of-care testing (POCT) due to its characteristics of cost-effectiveness, disposability, miniaturization, wide potential window, and easy of electrode design. Compared with gold or platinum electrodes, surface modification is difficult because the carbon surface is chemically or physically stable. Oxygen plasma can easily produce carboxyl groups on the carbon surface, which act as scaffolds for covalent bonds. However, the effect of O2-plasma treatment on electrode performance remains to be investigated from an electrochemical perspective, and sensor performance can be improved by clarifying the surface conditions of plasma treated biosensors. In this research, we compared antibody modification by plasma treated and physical adsorption, using our original immunosensor based on gold nanoparticles (AuNPs). Consequently, the O2-plasma treatment produced carboxyl groups on the electrode surface, which changed the electrochemical properties owing to electrostatic interactions. It was also found that the surface became hydrophilic, inhibiting non-specific antigen adsorption. The sensitivity was 6.5 times higher than the Limit of Detection (LOD) using physical adsorption.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Knowing, with reasonable accuracy, the dry matter (DM) content of Hass avocado fruit will help determine when the fruit must be harvested. The reliability of predictive models based on near infrared spectra for DM quantification depends on the ability of the spectra to be representative of the DM gradient within a whole fruit. The aim of this work was to develop a methodology to determine the optimum number of spectra to develop a robust model for DM content quantification. Three spectra were recorded for each zone of the intact fruit: peduncle, equator, and base. Each scanning point was sampled, and the DM content was determined using oven drying. Two-way ANOVA confirmed the DM gradient within the whole fruit. This gradient was observed within spectra using the RMS (root mean square) criterion and PCA. The PLS models showed that at least one spectrum per zone could be enough to construct an efficient and robust model for dry matter quantification.

Snowpack loss in midlatitude mountains is ubiquitously projected by Earth system models, though the magnitudes, persistence and time horizons of decline vary. Using daily downscaled hydroclimate and snow projections we examine changes in snow seasonality across the U.S. Pacific Southwest region during a simulated severe 20-year dry spell in the 21st century (2051–2070) developed as part of the 4th California Climate Change Assessment to provide a "stress test" for water resources. Across California’s mountains, substantial declines (30–100% loss) in median peak annual snow water equivalent accompany changes in snow seasonality throughout the region compared to the historic period. We find 80% of historic seasonal snowpacks transition to ephemeral conditions. Subsetting empirical-statistical wildfire projections for California by snow seasonality transition regions indicates a two-to-four-fold increase in burned area, consistent with recent observations of high elevation wildfires following extended drought conditions. By analyzing six of the major California snow-fed river systems we demonstrate snowpack reductions and seasonality transitions result in concomitant declines in annual runoff (47-58% of historic values). The negative impacts to statewide water supply reliability by the projected dry spell will likely be magnified by changes in snowpack seasonality and increased wildfire activity.

The present study illustrates a brain-computer interface designed and developed to be wearable, portable, and user-friendly. Eight dry electroencephalographic sensors were adopted to acquire the brain activity associated with motor imagery. Multimodal feedback in extended reality was exploited to improve the detection of neurological phenomena. Twenty-seven healthy subjects used the proposed system in five sessions to investigate the effects of feedback on motor imagery. The sample was divided into two equal-sized groups: the "neurofeedback" group, which performed motor imagery while receiving feedback, and the "control" group, which performed motor imagery with no feedback. Several questionnaires were administrated to participants aiming to investigate the usability of the proposed system and individual’s ability to imagine movements. The highest mean classification accuracy across subjects of control group was about 62 % with 3 % associated type A uncertainty, and 69 % with 3 % uncertainty for neurofeedback group. Moreover, in some cases the results were significantly higher for the neurofeedback group. The perceived usability by all participants was high. Overall, the study highlights the advantages and the pitfalls of using a wearable brain-computer interface with dry sensors. Notably, the results and the perceived usability pave the way for the employment of the proposed system in tele-rehabilitation.

Transition between the unfolded and native states of the ordered globular proteins is accompanied by accumulation of several intermediates, such as pre-molten globule, wet molten globule, and dry molten globule. Structurally equivalent conformations can serve as native functional states of intrinsically disordered proteins. This overview captures the characteristics and importance of these molten globules in both structured and intrinsically disordered proteins. It also discusses examples of engineered molten globules. The formation of these intermediates under the conditions of macromolecular crowding and their interactions with nanomaterials are also reviewed.

Dry eye disease (DED) most commonly caused by evaporative subtypes and mainly induced by meibomian gland dysfunction (MGD). Intense pulsed light (IPL) combined with meibomian gland expression (MGX) is noninvasive treatment for improvement of ocular discomfort symptoms and MGD. In this prospective study between November 2020 and May 2022, the patients met the criteria of both ocular surface disease index (OSDI) ≥13 scores and standardized patient evaluation of eye dryness (SPEED)≥ 8 scores were enrolled in Kaohsiung Veteran General Hospital. Three separate treatment sessions of IPL therapy combined with MGX administered to the lower lids with an interval of 28 days. Further tear film assessment included lipid layer thickness (LLT), tear meniscus height (TMH), non-invasive tear break-up time (NIBUT), meibomian gland loss (MGL) either beforeor after 1st and 3rd IPL therapy combined with MGX. Besides, lissamine green staining and pain scores were also recorded. We totally enrolled 37 patients of 74 eyes. Men accounted for 18.92% (7/37). The mean age was 54.51 ± 11.72 years. The mean OSDI scores were 58.12 ± 22, while the SPEED scores were 17.03 ± 5.98. The mean Schirmer’s test was 3.66 ± 2.43 mm. After three sessions IPL treatment with MGX, the OSDI, SPEED, LLT, TMH, MGL, MGXS and pain scores were significantly improved. For the MGX scores (MGXS) ≤20 group, MGL and lissamine green scores showed significant improvements. For the MGXS >20 group, TMH and dry spot rate revealed statistically improvement. Noninvasive IPL therapy with MGX statistically improved not only dry eye symptoms but also tear film assessments.

Sinkhole flooding is an essential hydrological process to recharge karst aquifer in arid to dry sub-humid regions. On the other hand, the increase of rain extremes is one of the major consequences of the global warming, together with the expansion of drylands. Thus, appropriate runoff regulation in endorheic karst basins in order to reduce the risk of flooding and improve the quantity and quality of the water drained by sinkholes will be more and more crucial. With these premises, a systematic review was performed by using WoS engine to infer the best practices for the karst water management in regions actually or potentially affected by water scarcity. Hydrological models are essential to manage the consequences of climate change on karst water resource, however the review shows that providing the tools necessary for reliable modeling is still challenging. Finally, due to the intrinsic vulnerability of the karst aquifers, pollution reduction and wastewater recycling policy will play key role in the next decades.

The WASP-Index is computed over Iberia for three monthly timescales in 1961-2020, based on an observational gridded precipitation dataset (E-OBS), and in 2021-2070, based on bias-corrected precipitation generated by a six-member climate model ensemble from EURO-CORDEX, under RCP4.5 and RCP8.5. The WASP performance in identifying extremely dry or wet events, reported by the EM-DAT disaster database, is assessed for 1961–2020. An overall good agreement between the WASP spatial patterns and the EM-DAT records is found. The areolar mean values revealed an upward trend in the frequency of occurrence of intermediate-to-severe dry events over Iberia, which will be strengthened in the future, particularly for the 12m-WASP intermediate dry events under RCP8.5. Besides, the number of 3m-WASP intermediate-to-severe wet events is projected to increase, mostly the severest events under RCP4.5, but no evidence was found for an increase in the number of more persistent (12m-WASP) wet events under both RCPs. Despite important spatial heterogeneities, an increase(decrease) of the intensity, duration, and frequency of occurrence of the 12m-WASP intermediate-to-severe dry(wet) events is found under both scenarios, mainly in the southernmost regions of Iberia, thus becoming more exposed to prolonged and severe droughts in the future, corroborating the results from previous studies.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

Epinephrine (EP, also called adrenaline) is a compound belonging to the catecholamine neurotransmitter family. It can cause neurodegenerative diseases such as Alzheimer’s disease, Parkinson’s disease, Huntington’s disease and amyotrophic lateral sclerosis. This work describes an amperometric sensor for the electroanalysis of EP, based on an inkjet-printed graphene electrode (IPGE), modified by a thin film of a laponite (La) clay mineral. The ion exchange properties and permeability of the prepared sensor (denoted La/IPGE) were evaluated using multi-sweep cyclic voltammetry while its charge transfer resistance was determined by electrochemical impedance spectroscopy. The results showed globally that La/IPGE exhibited more a sensitive response towards the detection of EP, in comparison with the bare IPGE. The developed sensor was directly applied for the determination of EP in aqueous solution using differential pulse voltammetry, and under optimized conditions, the calibration curve was plotted in the concentration range of 0.8 to 60 μM. The anodic peak current of EP was directly proportional to its concentration, leading to a detection limit of 0.29 μM. The sensor was successfully applied for the determination of EP in pharmaceutical preparation and best recovery rates were also obtained. The interfering effect of selected species was evaluated to highlight the selectivity of the elaborated sensor.

This study on the production of a modern natural water electrochemical antimony (II) test include the use of platinum platinum electrode electrodes. Antimony (II) was pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = -680 mV. Compared to the platinum electrode, the platinum nanoelectrode exhibited superior performance and, unexpectedly, received a higher electrochemical response. After 25 min of accumulation, time the best-defined anodic peak was obtained with 0.2 mol L^-1 KNO₃ pH 5.0. Using these parameters, the L^-1 Sb ^{2 +} calibration plot was linear over range 1 = 10⁻⁸ to 5x10⁻⁶ mol. The precision was tested by carrying out eight replicate measurements at a concentration of 2.5x10⁻⁵ mol. L^-1; the variance coefficient was 2.9%. The method was applied to analyte determination in water samples from the river. Other metal ion attack on Sb's (II) voltammetric response has been studied. In the SEM image, the nanoparticle electrode was clearly observed and characterized by X-ray diffraction and cyclic voltammetry

Protein malnutrition is present in developing countries but also in developed ones, due by the actual eating habits with insufficient protein intake, in addition to this it is estimated by the Food and Agricultural Organization of the United Nations an increase of world population of 9.1 billion people in less those 30 years, posing the challenge of nourish the mankind. There are different strategies to afford this challenge, one of the most promising ones is to approach novel protein sources like plants, microorganisms, and insects from dry lands.