In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

Oleogels are of high interest as promising substitutes for trans fats in foods. An emulsion-templated method was used to trap olive oil in the chitosan crosslinked with vanillin matrix. Oil in water emulsions (50:50 w/w) with different chitosan content (0.7 and 0.8% w/w) with constant vanillin/chitosan ratio (1.3) were air-dried at different temperatures (50, 60, 70 and 80ºC) and freeze-dried (-26ºC and 0.1 mbar) to produce oleogels. Only falling-rate periods were determined during air-drying kinetics and were successfully modelled with empirical and diffusional models. At drying temperature of 70ºC the drying kinetics were the fastest. Viscoelasticity of oleogels showed that elastic modulus significantly increased after drying at 60 and 70ºC, and those dried at 50ºC and freeze-dried were weaker. All oleogels showed high oil binding capacity (> 91%), but the highest values (> 97%) were obtained in oleogels with a threshold elastic modulus (50,000 Pa). Oleogels color depended on drying temperature and chitosan content (independent of the drying method). Significant differences were observed between air-dried and freeze-dried oleogels with respect to oxidative stability. Oxidation increased with air drying time regardless of chitosan content. Found results indicated that drying conditions must be carefully selected to produce oleogels with specific features.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Cirina forda caterpillars are a significant protein source in Central Africa, yet their preservation and consumption pose challenges. This study investigates the drying of Cirina forda caterpillars to enhance preservation methods and product quality. Caterpillars were subjected to drying experiments at temperatures ranging from 40°C to 70°C, using tunnel and oven dryers. The drying kinetics was analyzed using mathematical models, revealing a water diffusion-limited mechanism in all the tested conditions. The Newton model provided adequate estimations of the drying behavior, facilitating further practical dryer design. Shrinkage analysis indicated a two-step process independent of the drying conditions. Achieving a moisture content suitable for prolonged storage resulted in substantial volume loss, highlighting the challenges of preserving dried caterpillars. These findings shed light on how to optimize drying processes for Cirina forda caterpillars, crucial for sustaining protein sources in Central Africa.

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

This article deals with special curves similar to those known in mathematics as Lamé curves. Their equations have a certain similarity with the equations of Lamé curves. But these curves are more like ellipses in appearance. Like ellipses, they have major and minor axes. These are such curves that their major and minor semi-axis coincide with an ellipse but are different than an ellipse. The main feature of these curves is that for any triangle whose base coincides with the axis of a given curve and the vertex is on a given curve, the condition aⁿ+bⁿ=cⁿ is obtained. The number “n” is called the degree or rank of this curve. To distinguish this group of curves, we called them Elbe curves. The equations of these lines are also provided in the paper.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

The required processes and steps for making bread include technological and innovative concepts. The current trend is the use of less toxic compounds and green processes. Besides lactic acid bacteria and yeast, other microorganisms with special properties, such as enzymes, new aroma and flavor, exopolysaccharides, and vitamins, among other compounds with beneficial properties, could be added to bread manufacture, improving bread quality and health effects for the consumers. Freeze drying, new encapsulation methods, cryoprotectants, spray drying, fluidized bed drying, and vacuum drying are used for probiotics and microorganism cultures that will be used as starters or biological additives in the fermentation. The same development is observed in the preservation methods, and studies with plant extracts and essential oils have been proposed and introduced, replacing chemical agents, such as propionate, within the clean-label bread formulations concept. Baking science is a growing research line incorporating innovative methods and biological additives.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Nowadays, the fingerprinting methodologies of olive oils are dominated. They consider the entire analytical signal, which is acquired and recorded by the analytical instrument, directly from olive oil or isoleted fraction, i,e chromatogram. The shape and intensity of the recorded signal the instrumental fingerprint from the whole olive oil adulteration. Therefore, the methodolygy is based on the chemical composition (Fatty acids and Triglycerides compositions). However, Fatty acids composition as an indicator of purity suggests that linolenic acid content could be used as a parameter for the detection of extra virgin olive oil fraud with 5% of soybean oil. The adulteration could also be detected by the increase of the trans-fatty acid contents with 3% of soybean oil, 2% of corn oil and 4% of sunflower oil. The use of the ∆ECN42 proved to be effective in the Chemlali extra-virgin olive oil adulteration even at low levels: 1% of sunflower oil, 3% of soybean oil and 3% of corn oil. Therefore, compared to classical methods PCA and new approach of using LDA application could represent an alternative and innovative tool for faster and cheaper evaluation of extra-virgin olive oil adulteration.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Erigeron floribundus (Asteraceae) is an herbaceous plant widely used in the Cameroonian traditional medicine to treat various diseases of microbial and non-microbial origin. In the present study we evaluated the in vitro biological activities displayed by the essential oil obtained from the aerial parts of E. floribundus, namely the antioxidant, antimicrobial and antiproliferative activities. Moreover, we investigated the inhibitory effects of E. floribundus essential oil on nicotinate mononucleotide adenylyltransferase (NadD), a promising new target for developing novel antibiotics, and Trypanosoma brucei, the protozoan parasite responsible for Human African trypanosomiasis. The essential oil composition was dominated by spathulenol (12.2%), caryophyllene oxide (12.4%) and limonene (8.8%). The E. floribundus oil showed a good activity against Staphylococcus aureus (IZD of 14 mm, MIC of 512 µg/mL). Interestingly, it inhibited the NadD enzyme from S. aureus (IC50 of 98 µg/mL), with no effects on mammalian orthologue enzymes. In addition, T. brucei proliferation was inhibited with IC50 values of 33.5 µg/mL with the essential oil and 5.6 µg/mL with the active component limonene. The essential oil exhibited strong cytotoxicity on HCT 116 colon carcinoma cells with an IC50 value of 14.89 µg/mL, and remarkable ferric reducing antioxidant power (TEAC= 411.9 μmol TE/g).

Vacuum drying can dehydrate materials further than dry heat methods while protecting sensitive materials from thermal degradation. Many industries have shifted to vacuum drying as cost- or time-saving measures. Small-scale vacuum drying, however, has been limited by high costs of specialty scientific tools. To make vacuum drying more accessible, this study provides design and performance information for a small-scale open source vacuum oven, which can be fabricated from off-the-shelf and 3-D printed components. The oven is tested for drying speed and effective-ness on both waste plastic polyethylene terephthalate (PET) and a consortium of bacteria developed for bioprocessing of terephthalate wastes to assist in distributed recycling of PET for both additive manufacturing as well as potential food. Both materials can be damaged when exposed to high temperatures, making vacuum drying a desirable solution. The results showed the open source vacuum oven was effective at drying both plastic and biomaterials, drying at a higher rate than a hot-air dryer for small samples or for low volumes of water. The system can be constructed for less than 20% of commercial vacuum dryer costs for several laboratory-scale applications including dehydration of bio-organisms, drying plastic for distributed recycling and additive manufacturing, and chemical processing.

Natural phytochemicals in foods, including anthocyanins, can play an important role in human health. Anthocyanins have been reported to cause many various useful effects, such as reducing cancer cell proliferation, regulating blood pressure, preventing tumour formation, improving eyesight, and preventing diabetes. In this study, we aimed to reveal the qualitative anthocyanin content, antiproliferative and antimicrobial effects of different extracts derived from Vaccinium myrtillus, V. corymbosum, Sambucus nigra and Aronia melanocarpa. The anthocyanin content of the plants mentioned in the study was characterized after the freeze-drying process. MTT assay was used to determine the antiproliferative effect of extracts on cancer cells. Antimicrobial effects of extracts were studied on typical and clinical strains of 5 different bacteria. As a result, the anthocyanin content in the extracts obtained was determined to be quite good with the freeze-drying method, and it was also determined that the extracts had various levels of antiproliferative and antibacterial effects.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

Much research has been conducted to determine how hair regeneration is regulated, as this could provide therapeutic, cosmetic, and even psychological interventions for hair loss. The current study focused on the hair growth effect and effective utilization of fatty oil obtained from Bryde's whales through high-throughput DNA microarray approach in conjunction with immunohistochemical observations. The research also examined the mechanisms and factors involved in hair growth. In an experiment using female C57BL/6J mice, the vehicle control group (VC: propylene glycol: ethanol: water), the positive control group (MXD: 3% minoxidil), and the experimental group (WO: 20% Whale Oil) were topically applied to the back of the mouse. The results showed that 3% MXD and 20% WO were more effective than VC in promoting hair growth, especially 20% WO. Furthermore, in hematoxylin and eosin-stained skin tissue, an increase in the number of hair follicles and subcutaneous tissue thickness was observed with 20% WO. Whole-genome transcriptomic analysis also showed that 20% WO may have lower stress- and inflammation-related responses than 3% MXD. Therefore, whale oil can be expected to be used as a safe hair growth agent.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

This study aimed to determine whether camelina oil is safe for use in canine diets, using canola oil and flax oil as controls as they are similar and generally regarded as safe (GRAS) for canine diets. Thirty privately-owned adult dogs of various breeds (17 females; 13 males), with an average age of 7.2 ± 3.1 years (mean ± SD) and body weight (BW) of 27.4 ± 14.0 were used. After a 4-week wash-in period using sunflower oil and kibble, dogs were blocked by breed, age, and size, and randomly allocated to one of three treatment oils (camelina (CAM), flax (FLX), or canola (OLA)) at a level of 8.2 g oil/100g total dietary intake. Body condition score (BCS), BW, food intake (FI), and hematological and select biochemical parameters were measured at various timepoints over a 16-week feeding period. All data were analyzed with ANOVA using PROC GLIMMIX of SAS. No biologically significant differences were seen between treatment groups for BW, BCS, FI, hematological and biochemical results. Statistically significant differences noted among some serum biochemical results were considered small and due to normal biological variation. These results support a conclusion that camelina oil is safe for use in canine nutrition.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

The increasing prevalence of obesity and sedentary lifestyles has led to an increased incidence of metabolic syndrome (MetS) worldwide. In Taiwan, middle-aged women are at a greater risk of MetS, type 2 diabetes, and cardiovascular disease than men are because they have more subcutaneous fat and larger waist circumferences compared to men with equal visceral fat levels. This study investigated the effects of calorie restriction supplemented with fish oil (CRF) in middle-aged women with MetS. For 12 weeks, 75 eligible participants were randomly assigned either calorie restriction (CR) or CRF. Both dietary intervention groups were further divided into two age groups: ≤45 and >45 years. The changes in MetS severity, inflammatory status, iron status, and red blood cell fatty acid profile were evaluated. Seventy-one participants completed the trial. Both dietary interventions significantly ameliorated MetS and improved the participants’ inflammatory status. CR significantly increased total iron binding capacity, whereas CRF increased hepcidin levels. Furthermore, CRF significantly increased the n-6/n-3 and arachidonic acid/docosahexaenoic acid ratios. In conclusion, CR and CRF improved the anthropometric and MetS characteristics of early-middle aged women, including body weight, blood glucose levels, triglyceride levels, as well as the scores for the homeostasis model assessment of insulin resistance and quantitative insulin sensitivity cheque index. Dietary intervention was more effective in >45-year-old women than ≤45-year-old women.

This study has two main focuses: the first focus is to explore the design and the behavior of a locally built solar dryer during processing henna leaves. This was performed through the determination of the most important parameters that have effect on the drying process. Appropriately, it was found that the outlet air temperature of the solar collector depends entirely on the solar radiation, Moreover, the inlet temperature of the air to the drying chamber has also an important impact on the moisture content of the product. It was found that most of the studies dealing with solar drying do not take into consideration the quality of the final product. Accordingly, the second objective of this study is to present the effect of drying process on the quality of the drier samples. For this purpose, the bioactivity of the samples, in terms of determination of the total phenol content, total flavonoid content, and antioxidant activities was performed. Three different samples: fresh sample, samples dried with the presented solar dryer and open solar dried samples are tested. It was found that samples dried with the solar dryer presented the best results.

The objective of this study was to evaluate the drying kinetics of the mass of jambu leaves and mass of jambu leaves in foam mat at different temperatures (50, 60 and 70 °C and thickness of 1.0 cm). The physicochemical characterization of the materials was performed before and after drying. Twelve different drying models were fitted to the drying kinetics data and the thermodynamic properties were calculated. The physicochemical parameters for the mass of leaves and foam after drying were moisture content from 2 to 7%, ash from 13 to 17%, protein content from 22 to 30%, lipids from 0.6 to 4% and total titratable acidity from 0.20 to 0.28% of tartaric acid. Wang & Singh and Midilli models were recommended for describing the drying kinetics. The use of foam mat promoted higher values of effective diffusion coefficient and activation energy and lower values of enthalpy and entropy, thus enhancing the reduction of drying time.

The most relevant fungal disease of the olive tree in Portugal is anthracnose, which has negative effects on fruit destruction and consequently on the yield and quality of the olive oil. Moreover, the loss of quality caused by olive fruit fly is associated with the presence of fungi in the galleries made by the larvae. The present study focuses on the effect of olive anthracnose and olive fly on the content of bioactive compounds, namely on hydroxytyrosol (HYT) and its derivatives (health claim) in olive oils extracted from 'Galega Vulgar' and 'Cobrançosa' cultivars. The olives, with different damage levels (olive fly and anthracnose disease), were harvested in Castelo Branco (Center of Portugal) in organic rainfed orchards, at four harvest times during 2019, 2020 and 2021 harvest years. The fruits were immediately submitted to olive oil extraction. The results of the quality criteria show that Galega olive oils extracted from olives with a higher anthracnose incidence show no conformity for the Extra Virgin Olive Oil (EVOO) and Virgin Olive Oil (VOO) categories, with high acidity values and negative sensory notes accompanied by the disappearance of oleacein (the main phenolic compound of both monovarietal olive oils). Conversely, no sensory defects were observed in Cobrançosa olive oils extracted from fruit with high anthracnose and olive fly incidence. Moreover, despite a decrease in all the positive attributes associated with the cultivar, namely in oleacein and oleocanthal contents, quality criteria were still in accordance with the EVOO category. The total HYT and tyrosol (TYR) content (> 5 mg/20g) allows the use of the health claim on the label of all the analysed Cobrançosa olive oils.

Public key encryption methods are often used to create a digital signature, and where Bob has a public key and a private key. In order to prove his identity, he will encrypt something related to the message with his private key, and which can then be checked with his public key. The main current methods of public-key encryption include RSA and ECC (Elliptic Curve Cryptography), and which involve computationally difficult operations. But these operations have not been proven to be hard in an era of quantum computers. One well-known hard problem is the solving of quadratic equations with $m$ equations with $n$ variables. This is a known NP-hard problem, even in a world of quantum computers. These can be used as post-quantum signature schemes and which involve multivariate equations. In order to understand these methods, this paper outlines a simple example of implementing the oil and vinegar method, and where we have a number of unknown oil variables and a number of known vinegar variables, and where the vinegar variables help convert the hard problem into an easy one.

Two-phase olive pomace is a byproduct of the olive-oil extraction process that is sometimes processed further to recover more oil. During pomace oil production, especially in the early stages of olive processing, odours can be produced. These odours are a serious nuisance especially in and around the processing facilities, as well as for nearby communities. These odours can be strong and unpleasant, and they may result in various issues, including environmental concerns. Thus, in this paper, the effect of storage and drying on the composition of two-phase olive pomace was investigated. Several physicochemical and instrumental analyses were performed and it was concluded that the structural elements of pomace are not the ones who are affected during storage and drying. Storage and drying mainly impact the oil content of pomace, leading to an acidity increase and to the production of odorous oxidation compounds. Volatile acids, methyl and ethyl esters are released into the atmosphere causing serious environmental nuisance.

The study of the impact of polyQ expansion driven proteotoxicity on cell metabolism has evi-denced NAD molecule as a central player in regulating metabolic response and cell repair in neurodegeneration. The decline in NAD intracellular levels represents a hallmark of ageing aris-ing from a dysregulation between NAD-consuming and biosynthetic enzymatic reactions in which NMNAT plays a key role. By an integrated bioanalytical and proteomic experimental design, the derangement of NAD metabolism deriving from the accumulation of polyQ-Htt protein has been analysed in Saccha-romices cerevisiae harbouring a 103Q-Htt and compared with wild-type Htt, in absence and in presence of a phenolic extract from EVOO, as a source of antioxidant bioactive compounds. Quantification of NAD and its precursors and proteomic analysis of the differential protein ex-pression has been performed by LC-DAD-MS. Chronological lifespan and NAD homeostasis was strongly impaired by proteotoxic polyQ-Htt, eliciting a depletion of NAD levels and accumulation of NaMN. In parallel a downregulation of Sirt2 expression levels has been observed. Phenolic extract administration had no meaningful ef-fects on NAD replenishment to prevent proteotoxicity. NaMN can represent a biomarker of accel-erated aging, and/or a signaling molecule for cell repair.

Grape dehydration is practiced widely in the food industry with large yields of sultanas produced globally. This paper proposes an investigation into grape microstructure changes as it is dried by imaging specimens at intervals during dehydration at two temperatures using scanning electron microscopy. Detailed images of the microstructure were obtained, and a unique image processing algorithm was developed to quantitatively analyse the properties of this microstructure. Two main methods were developed to obtain the complex boundaries of cells present in the grape tissue in over 36 SEM images. Segmentation of the binary image using an adapted watershed function obtained the most consistent and accurate morphological shape. This was compared to a secondary method which used Canny’s edge detection function, morphological closing and skeletonizing to outlines the cellular microstructure. MATLAB was utilised to convert these boundaries into measurable areas so that quantitative data on average cell area, perimeter and cell axis lengths was acquired. It was found that over drying time cell area and perimeter reduced as expected. Some variability in the data was clear due to only single samples being analysed for each temperature and time combination. The development of automatic image processing techniques will enable quantitative data to be extracted from these images. Trends in cell perimeter, diameter and shape will be used to demonstrate relationships between morphological structure, drying temperature, and duration.

Methylsilsesquioxane aerogels with uniform mesopores have been facilely prepared via a sol–gel process followed by microwave drying with methyltrimethoxysilane (MTMS) as precursor, hydrochloric acid (HCl) as catalyst, water and methanol as solvents, hexadecyltrimethylammonium chloride (CTAC) as surfactant and template and propylene oxide (PO) as gelation agent. The microstructure, chemical composition and pore structures of the resultant MSQ aerogels were investigated in detail to achieve controllable preparation of MSQ aerogels, and the thermal stability of MSQ aerogels was also analyzed. The gelation agent, catalyst, solvent and microwave power have important roles on pore structures of MSQ aerogels. Meanwhile, microwave drying method is found to not only have a remarkable effect on improving production efficiency, but also be conducive to avoid the collapse of pore structure especially micropores during drying. The resulting MSQ aerogel microwave-dried at 500 W possesses a specific surface area up to 821 m2/g and a mesopore size of 20 nm, and displays good thermal stability.

The formation of hydrogen sulfide (H₂S) in petroleum reservoirs by anaerobic microbial activity is called biogenic souring of reservoirs and is a risk in the oil and gas industry as the compound is extremely toxic, flammable and corrosive. In this paper, we present a workflow and the tools to assess biogenic souring from a pragmatic engineering perspective. The retention of H₂S in the reservoir due to the reactions with iron-bearing rock minerals (e.g. siderite) is shown in a theoretical approach here and supported with literature data. Cases are given for two fields under secondary (waterflooding) and tertiary flooding with microbial enhanced oil recovery (MEOR). The use of the Monte Carlo method as a numerical modelling tool to incorporate uncertainties in the measured physical/chemical/ biochemical data is demonstrated as well. A list of studies conducted with different chemicals alone or in combination with various biocides to mitigate biogenic souring provides an overview of potential inhibitors as well as possible applications. Furthermore, the results of static and dynamic inhibition tests using molybdate are presented in more detail due to its promising mitigation ability. Finally, a three-step workflow for the risk assessment of biogenic souring and its possible mitigation is presented and discussed.

Objectives The aim of the study is to evaluate the effectiveness of extra virgin olive oil (EVO) and fruity oil for the treatment of gingivitis. Materials and Methods. A sample of 75 patients with gingivitis induced by plaque bacteria, over 18 years of age, was divided into three groups: a study group A with extra virgin olive oil, a study group B with fruity oil and a control group C. In the two study groups, Evo oil was administered as a mouthwash in patients with gingival inflammation. The protocol included a daily application of the product for 30 days, with three recalls 15 days apart. Clinical parameters of plaque formation and gingivitis - plaque index (PI), bleeding index (BI) were assessed at each recall and scored on a specific periodontal chart. The control group re-ceived no mouthwash treatment to normal daily oral hygiene procedures, and the same clinical parameters as the study group were evaluated. Data were evaluated using SPSS 27.0 software for Windows (SPSS Inc., Chica-go, IL, USA). Then, the pre- and post-treatment values of the groups were compared using the t-student test, set-ting P < 0.05 as the significance level. Results Comparison with the three groups showed that extra virgin olive oil was an adjuvant in the treatment of gingival inflammation, improving PI and BI. In group A, mean plaque index had a 48% reduction and bleeding index 64% reduction, after 30 days. In group B, the mean plaque index had a 35% reduction and a bleeding index reduction of 43%, after 30 days. Conclusion The collected data showed significant improvements in the formation of bacterial plaque and gingi-vitis. the exact mechanism of such treatment is still to be elucidated. As a result of this, further studies with a different sample of patients to those used and a comparison with other products need to be addressed to verify and demonstrate the antibacterial and anti-inflammatory effect of the components of this natural product.

In recent years, the potential of insects has been explored as a sustainable protein alternative to sustain the growing world population. Differences in the way insects are processed can affect their proximate composition and digestibility. This work studies the effects of the combination of different types of slaughter methods and drying temperatures on the proximate composition, organic matter digestibility (OMd), hydrolysis degree (DH/NH2 and DH/100 g DM), total hydrolysis (TH) and hygienic sanitary study of BSFL (black soldier fly larvae). Four types of slaughter methods were used: frozen (F), blanched + frozen (B), Melacide® + frozen (M) and liquid nitrogen (N), each with three drying temperatures (50, 70 and 90 °C). A negative correlation between acid detergent fibre (ADF) and protein digestibility parameters was obtained. 70 °C was the most suitable drying temperature, as it reported higher values of protein digestibility (DH, TH), resulting in hygienic and sanitary conditions suitable for food use. Slaughtering with liquid nitrogen and blanching were more convenient than traditional freezing or the use of Melacide® to achieve higher protein digestibility results.

Microencapsulation by atomization can be used to minimize the loss of bioactive compounds, improving the characteristics and applicability of the powdered product. This study evaluates the effect of different encapsulating agents (maltodextrin, gum arabic, and chitosan) and three spray nozzle diameters (1.0, 1.2, and 1.5 mm) on the atomization of guavira (Campomanesia adamantium) pulp with added 6% bocaiuva (Acrocomia aculeata) dehydrated pulp in the green maturation stage. The experiment followed a simplex-centroid mixed design, with carrier agent concentrations and spray nozzle diameters as independent variables and powder yield, solubility, hygroscopicity, and vitamin C content as dependent variables. The results show that gum arabica increased powder yield and vitamin C retention. The addition of maltodextrin resulted in powders with increased solubility and low hygroscopicity. Furthermore, the optimization tool indicated that the best process conditions were achieved with the addition of gum arabic (10.8%) and chitosan (7.2%), resulting in powders with 29.48% yield, 82.96% solubility, 15.90% hygroscopicity and 741.11 mg/100g vitamin C. Furthermore, the 1.0 mm diameter spray nozzle was considered the most suitable for obtaining guavira pulp microparticles with higher ascorbic acid content.

Keywords: keyword 1; keyword 2; keyword 3 (List three to ten pertinent keywords specific to the article yet reasonably common within the subject discipline.)

This study investigates the use of programming language Python to analyse and model chemical engineering processes. Using municipal sewage sludge (MSS) drying as an example, the study demonstrates how Python can support analyses and model drying data. The drying process was performed on a flat plate while maintaining a uniform, parallel drying air speed of 1.15 m s-1. The Python program helped to analyse the digitalised weight measurements from each sample. The program enables sorting input data, determining the drying critical point and evaluating the first and second drying periods.

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

Fresh potatoes were deep-fried in olive oil (OO) & extra virgin olive oil (EVOO) and their blends with 5%, 10% and 20% v/v sesame oil (SO). This is the first report on the use of sesame oil as natural source of antioxidant for olive oil deep-frying. Oil was evaluated for Peroxide Value (PV), Free Fatty Acids (FFA), K₂₃₂, K₂₇₀, Trolox Equivalent Antioxidant Capacity (TEAC) and Total Phenols (TP) until Total Polar Compounds (TPCs) reached 25%. Sesame lignan transformations were monitored through Reverse-phase HPLC. While TPCs in olive oils increased at a steady rate, the addition of 5%, 10% and 20% v/v SO created a time window lasting 1, 2 and 3 hours, respectively, where TPCs were constant. SO addition to OO increased the total frying time. Furthermore, the addition of SO reduced the peroxides formation rate for both OO and EVOO. EVOO was more resistant to oxidation than OO as measured by TPCs and TEAC, while frying time raised from 21.5 to 25.25 h when EVOO replaced OO. The increase in frying time for olive oil but not for extra virgin olive oil, after SO addition, is pointing out a niche market for extra virgin olive oil in deep-frying.

The microwave field is used for drying and disinfection of grain, during pre-sowing seed treat-ment. The use of a microwave field in these installations leads to an increase in their productivity and a decrease in the energy consumed by them. One of the principal problems of microwave field use for treatment of dense grain layers is to insure sufficient distribution uniformity of the field. In this article, waveguide design options have been discussed that serve to introduce microwave radiation into the grain layer. Mathematical simulation of the electromagnetic field distribution was performed with the use of CST Microwave Studio software in order to evaluate and compare horn-type, rectangular and semicircular waveguides. The data on the standing wave ratio and radiation efficiency for these types of waveguides have been reported. Specific features of the microwave electromagnetic field distribution and radiation power in the output of those wave-guides have been described. Results of mathematical simulations enabled to make out that sem-icircular waveguides with slot-type radiators are preferable for processing dense grain layers.

The potential of sodium alginate (ALG) and gum arabic (GA) as wall polymers for L-ascorbic acid (AA) encapsulation as a tool for their preservation against the thermo-oxidative degradation was investigated. The influence of such polymers used as wall material on the AA-content, size, encapsulation efficiency, encapsulation yield and thermo-oxidative stability were evaluated. The AA-microparticles were obtained using the spray-drying technique. An experimental Taguchi design was employed to assess the influence of the variables in the encapsulation process. The microparticles morphology and size distribution were characterized by scanning electron microscopy and laser diffraction. The thermal stability of AA microparticles was studied by differential scanning calorimetry and thermogravimetry analysis. This work points out the viability to encapsulate AA using GA and ALG through a spray-drying process. In general, a product yield ranging from 35.1% to 83.2% and an encapsulation efficiency above 90% was reached. Spherical microparticles with a smooth surface were obtained with a mean diameter around 6 μm and 9 μm for the those prepared with GA and ALG, respectively. The thermo-oxidative analysis showed that both polymers allow maintaining AA stable up to 188 °C, which is higher than the traditional processing temperature used in the fish feed industry.

Trailing oil is the tail section of contamination. There are two main reasons for the formation of trailing oil, one is the effect of laminar flow boundary layer, the other is the outflow of the preceding batch remained in the dead-legs. In the batch transportation of refined oil, under the action of viscous force, the preceding batch forms laminar boundary layer near the pipe wall and stays on the pipe wall, resulting in the phenomenon of contamination trailing and formation of trailing oil. When oil passes through the valve chamber of the oil transportation station, dead-leg will be formed. Due to gravity and convection diffusion, preceding batch flowing from dead-legs will form trailing oil in the pipeline. The phenomenon of trailing oil exists in the process of batch transportation, which will have an effect on the quality of oil. In this paper, Reynolds time-averaged method is used to simulate turbulence.Computational Fluid Dynamics(CFD) software is used to simulate different flow rates and bypass lengths to obtain contamination-related experimental data.Matlab software is used to perform multi-nonlinear regression for the oil substitution time, the length of the bypass and the flow rate. The formula for calculating the length of the trailing oil produced by the dead-leg is obtained. The modified formula for calculating the length of the contamination is obtained by combining the existing formula for calculating the length of the contamination.

This study aimed to evaluate the effect of incorporating linseed oil and fish oil in the diet on intake, ruminal fermentation milk yield and milk fatty acid profile in dairy goats. Four crossbred Saanen lactating goats in mid-lactation and milking 1.30±0.28 g/day were used in a 4 × 4 Latin square design. The basal diet consisted of concentrate and Para grass (C:F 40:60). Treatments included the basal diet without oil supplement (Ctrl) or with 2.5% linseed oil (LO2.5), 2.5% linseed oil and fish oil (3:2, w/w, LFO2.5), and 4.16% linseed oil and fish oil (3:2, w/w, LFO4.16). Diets had no effect on intake, milk yield, milk composition and ruminal fermentation patterns (P > 0.05). The lower (P < 0.05) proportions of C10:0-C14:0 in milk fat were observed with LFO4.16 compared with Ctrl. Compared with the Ctrl and linseed oil added alone, feeding LFO4.16 resulted in a 589% and 303% increase in C18:1 t11, respectively. Milk c9,t11 CLA was markedly increased with the LFO4.16 diet, accounting for 4.53 and 2.94 times greater concentrations than those in Ctrl and LO2.5 diets, respectively (P < 0.01). Goats fed LFO2.5 and LFO4.16 had greater levels of C22:6n-3 (0.63% and 0.87%; P < 0.001) compared with those fed Ctrl and LO2.5 diets (0.06% and 0.08%). Overall, the combined data suggested that including 4.16% linseed oil and fish oil in the diet of dairy goats is effective for improving the concentrations of healthy fatty acids in milk, without affecting milk production.

Umbu is a tropical fruit with high content of bioactive compounds. However, maturation causes significant losses on nutrient density reducing the nutritional value of this highly appreciated fruit. Thus, the objective of the present work was to encapsulate the Umbu fruit bioactive compounds using spray drying and identify the variables affecting the biomolecules preservation. A Box-Behnken experimental design with 3 factors was set varying inlet temperature, atomization flow rate, and maltodextrin concentration for process otimization. Then the powder physicochemical and chemical properties were characterized, and results were modeled using a polynomial equation. Results revealed that the droplet size and maltodextrin concentration had a significant influence on the conservation of the biomolecules. Drying kinetics favoring fast formation of a particle crust increases encapsulation efficiency. Bioactive compounds retention was achieved by increasing maltodextrin even at high temperatures, where a matrix is formed hindering chemical degradation. Process optimization was validated and revealed low inlet temperatures (122ºC), high atomization flow rate (5kg/h) and high maltodextrin concentration (20%) to be the most desirable conditions for bioactive compounds retention.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

Olive tree vegetal materials are considered a powerful source for isolation of bioactive compounds, mainly, phenols and triterpenic acids. However, the high humidity content of them reduces their preservation and extractability to a liquid solvent. Accordingly, a drying step is crucial to homogenize the material and to obtain an efficiency extraction. We studied the influence of the drying process on the extraction efficiency of bioactive compounds from olive vegetal material. For this purpose, we evaluated the effects of four drying processes on the solid–liquid extraction of bioactive compounds from two by-products, olive leaves and pomace, and olive fruits harvested from two cultivars, Alfafara and Koroneiki. Infrared-assisted drying (IAD) was the most suited approach to obtain extracts enriched in oleuropein from leaves. In the case of pomace, lyophilization and microwaves-assisted drying led to extracts concentrated in oleacein and oleuropein aglycone, whereas IAD and oven-drying led to extracts with enhanced content in hydroxytyrosol glucoside and hydroxytyrosol, respectively. The drying process affected considerably to the chemical composition of extracts obtained from fruits. Changes in the composition of extracts were explained essentially by the drying process conditions using auxiliary energies, temperature and time, which promoted chemical alterations and increased the extractability of compounds.

Aqueous and ethanolic extracts of Hibiscus sabdariffa were spray-drying using maltodextrin (MD) and gum arabic (GA) as carriers agents. An experimental design Taguchi L8 with seven variables was implemented. Physicochemical properties in the encapsulates were evaluated by UV-Vis, XRD, spectroscopy and gravimetric techniques. Treatments with aqueous extracts showed the highest concentration of total soluble polyphenols (TSP) 32.12- 21.23 mg EAG/g DW, and antioxidant capacity (AOX) for ABTS assay. The best treatment for TSP and AOX was T4: 2.5% Hibiscus w/w, aqueous extracts, decoction, extract-to-carrier ratio 1:1 (w/w), proportion to carriers (MD:GA) 80:20 (w/w), 10000 rpm, 150°C. Taguchi L8 model is a tool that allows the use of multiple variables with a low number of treatments that indicate the drying conditions that give the best parameters, focusing mainly on TSP and AOX, in addition, is a good alternative for the preservation and stability of the PC in Hibiscus.

The study investigates the evolution of soil pore structure and shear strength deterioration in compacted clayey soil under controlled wetting and drying (wd) cycles, which are expected to become more frequent due to climate change. Thirty soil samples were compacted at optimal moisture content and 90% of maximum dry density. These samples were then subjected to 0, 1, 5, 10, and 15 controlled wd cycles from saturation to the wilting point, and volumetric changes were recorded during each cycle. After the wd treatment, the soil samples were scanned using X-ray Computed Tomography (CT) at 50 μm resolution and then sheared under unconsolidated-undrained and consolidated-undrained conditions in a triaxial test. Significant shrinkage and swelling of soil samples were observed during wd cycles, with average volumetric strain fluctuating between +12% at saturation and -5% at the wilting point. X-ray CT visualisation and analysis revealed higher porosity, more prominent pores and increased pore length in soil samples with increasing wd cycles. Both undrained and effective soil shear strength markedly decreased with increasing wd cycles. CT-derived macroporosity and pore length were significant predictors of the soil's undrained and effective shear strength when exposed to wd cycles. The findings emphasise the considerable impact of climate change, specifically wd cycles, on clayey soil, highlighting the need for consideration in the design of earth-based infrastructure.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

This study presents an experimental investigation of the convective drying process of ginger rhizomes (Zingiber officinale). It analyses the effect of moisture content on the thermal properties of dried ginger rhizomes. Drying experiments were conducted under controlled conditions to establish the relationship between moisture content and thermal conductivity. The drying kinetics were examined to provide insights into the drying behaviour of ginger rhizomes and the influence of moisture content on their thermal properties. The results demonstrated a significant impact of initial moisture content and convective drying conditions on the drying process. As drying progressed, the moisture content decreased, leading to a reduction in thermal conductivity. It was observed that drying under convective drying takes 24 hours compared to open sun drying at nine days and solar tunnel drying at eight days. The drying temperature of 60°C was considered optimum. The results show that dried ginger at an absolute moisture content of 6.63% (wb) with a thermal conductivity of 0.0553W/m. K for unblanched ginger, 9.04% (wb) with thermal conductivity of 0.0516W/m. K for blanched ginger, 8.56% (wb) moisture content with a thermal conductivity of 0.0483W/m. K for peeled ginger and 5.98% moisture content with a thermal conductivity of 0.0460W/m. K for unpeeled ginger would be ideal for making powdered ginger rhizomes. These findings have practical implications for the food industry, as they can aid in designing and improving drying processes for ginger rhizomes and similar agricultural products. By understanding the relationship between moisture content and thermal properties, more efficient drying strategies can be developed to minimise energy consumption and maintain the quality of the dried product.

Drought events are predicted to become more prevalent in the future. Evaluating the performance of herbicide-resistant and susceptible weed ecotypes to progressive drought can provide insights into whether resistance trait(s) increased or reduced the fitness of a resistant population. Two experiments were conducted in the greenhouse between January and May 2021 to evaluate drought tolerance differences between Palmer amaranth accessions resistant to S-metolachlor or glyphosate and their susceptible counterparts. The accessions used were: S-metolachlor-resistant (17TUN-A), a susceptible standard (09CRW-A), and glyphosate-resistant (22 to 165 EPSPS copies) and glyphosate-susceptible (3 to 10 EPSPS copies) plants from accession 16CRW-D. Daily transpiration of each plant was measured. The daily transpiration rate was converted to normalized transpiration ratio (NTR) using a double-normalization procedure. The daily soil water content was expressed as a fraction of transpirable soil water (FTSW). The threshold FTSW (FTSWcr), after which NTR decreases linearly, was estimated using a two-segment linear regression analysis. The data showed differences between S-metolachlor- resistant and -susceptible accessions (P ≤ 0.05). The FTSW remaining in the soil at the breakpoint for the S-metolachlor-susceptible accession (09CRW-A) was 0.17±0.007. The FTSW remaining in the soil at the breakpoint for the S-metolachlor-resistant accession (17TUN-A) was 0.23±0.004. Although the mechanism endowing resistance to S-metolachlor might have contributed to increased drought tolerance, follow-up experiments are needed to verify this finding. Increased EPSPS copy number did not improve drought tolerance of Palmer amaranth.

Onion (Allium cepa L.) is a strong-flavoring vegetable consumed in different ways. It is mainly due its distinctive flavor or simply pungency. Onion has also important natural compounds effective for medical functions such as inhibition of bone resorption, lower risk of cardiovascular disease and cancer. This importance is directly related to high content of organo-sulphur compounds. Shelf life of fresh onion bulb is short enough about two weeks at ambient storage conditions in Fogera district, Amhara region, Ethiopia. This is mainly due to the presence of high moisture in fresh onion bulbs. Postharvest loss of onion bulb reaches up to 50% in the production season in Fogera district. Consequently onion bulb had extreme variable market price during production and off season in the district which directly influences both the growers and consumers. In this study the effect of different drying techniques on nutritional and volatile components of onion were evaluated. Effect of different drying techniques on protein, carbohydrate, total sugar, fat, pyurvic acid, ascorbic acid, total phenol, total flovonol, rehydration ratio, color and sensory properties of onion slice were evaluated and found insignificant at (P > 0.05) for microwave and modified direct solar dryers taking fresh onion bulb as a control. But oven drying method had significant effect on onion physicochemical quality attributes at (P < 0.05) as compared to fresh onion bulbs.

In this paper, the main characteristics of the natural bitumen of the Munaily-Mola oil sands were studied with comparison crude oil of Karazhanbas oil field. During the experiment, the density, heating value, ash content and elemental composition of natural bitumen were determined, and these parameters were compared with the properties of Karazhanbas crude oil. As well as oil, resin and asphaltene fractions of both hydrocarbons were separated and each of them were analyzed at a Fourier transform IR-spectroscopy Spectrum-65 with 450-4000 cm−1 range. According to these indicators, it is concluded that natural bitumen is a heavy hydrocarbon raw material with highly resin-asphaltene compounds. Like Karazhanbas oil, natural bitumen can be used as a raw material for various petrochemical products. By finding ways of effective processing of natural bitumen, it can be used in useful areas of the national economy.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

The focus of this study was to evaluate the effectiveness of incorporation of phenolic compounds from blueberry juice into pear slices using a combination of ohmic heating (OH) and vacuum impregnation (VI), followed by air- or freeze-drying. The results showed that OH is a valuable technique to increase the content of bioactive compounds and antioxidant capacity of blueberry juice. The optimal OH treatment is heating the juice at 50 °C for 20 min under an electric field of 13 V/cm. Furthermore, the combination of VI and OH showed the efficiency of enriching pear slices with bioactive compounds from blueberry juice. The best treatment is to immerse the slices for 90 min at 50 °C and an electric field of 7.8 V/cm. The presence of anthocyanin pigments from blueberry juice affects the color parameters of pear slices by increasing the a* parameter and decreasing the b* and L* parameters. However, both freeze-drying and air-drying (at temperatures of 40, 50, and 60 °C) negatively affected the phenolic content and antioxidant capacity. Notably, air-drying at 60 °C highest levels of phenolic compounds and antioxidant potential for both impregnated and non-impregnated pear slices among the drying processes applied.

This research work is concerned in the exergy analysis of the continuous-convection drying of onion. The influence of temperature and air flow rate was studied in terms of exergy parameters. The energy and exergy balances were carried out taking into account the onion drying chamber. Its behaviour was analysed based on exergy efficiency, exergy loss rate, exergetic improvement potential rate and sustainability index. The exergy loss rates increase with the temperature and air flow rate augmentation. Exergy loss rate is augmented at higher drying air temperatures and flow rates because the overall heat transfer coefficient increase. On the other hand, the exergy efficiency increases with the air flow rate augmentation. This behavior is due to the energy utilization was improved because the most amount of supplied energy was utilized for the moisture evaporation. However, the exergy efficiency decreases with the temperature augmentation due to the free moisture is less, then, the moisture begins diffusing from the internal structure to the surface. The exergetic improvement potential rate values show that the onion drying process presents a high potential to improve the exergy efficiency. The sustainability index of the drying chamber varied from 1.9 to 5.1. To reduce the environmental impact of the process, the parameters must be modified in order to ameliorate the exergy efficiency of the process.

With the rapid spread of carbon trading in the global economy, the interactions of prices between carbon (or clean/renewable energy) and traditional fossil energies such as coal and oil have raised growing attention, but little research have discussed their dynamic volatility spillover and time-varying correlation. The purpose of this study is to investigate these issues, for the weekly data of EUA futures, Biofuel and Brent oil prices from 25 October 2009 to 5 July 2020. We employ the VAR-GARCH model with the BEKK specification. Our results are summarized as follows. At first, we identified the sudden changes and the volatility persistence in the three markets, and also confirmed that the volatility of the markets has changed significantly over time. Secondly, we find that there are a weak volatility spillover effect among the three markets, while a strong spillover effect between the EUA and Brent oil markets. Lastly, in financial markets, the EUA can be used as a hedging portfolio for the Biofuel and Brent oil markets. These results can help investors to well compose their portfolios and manage their investment risks, and help potential pollutant emission sources to join in carbon market in a cost-effective way.

The present reality about the Nigerian economy calls for investment and development in the non-oil sector. This becomes necessary as a result of fall in the oil price in the global market. This paper examined the Bayesian Vector Autoregression (BVAR) modeling and forecasting of the dynamic interrelationship between Economic growth and revenue from the oil and non-oil sectors in Nigeria. To achieve this, annual data on Gross Domestic Product (GDP), revenue from oil and non-oil sectors were collected from Central Bank of Nigeria (CBN) bulletin, the sample from 1981 to 2008 was used for analysis, while sample from 2009 to 2014 was used for model validation. Six (6) versions of Sims-Zha BVAR models were compared for out-of-sample forecast, the result revealed the superiority of the BVAR6 model over the other BVAR models. Lastly, evidence from the decomposition forecast errors revealed that revenue of oil sector contributed 7.69% to GDP while revenue from non-oil sector contributed 0.12% to GDP in Nigeria. This paper therefore recommended that the present government should encourage investment that is geared toward development in the non-oil sector, of which it has the capacity to improve the Economic growth of the Nigerian economy.

Oil revenues and external debt might have stimulated economic growth in the oil exporting countries via investment in capital projects. The paper estimated economic growth on oil revenues and external debt after controlling public investment and population growth over the period 1970-2015. Following the confirmation of the order of integration, our analysis is based on autoregressive distributed lag bound testing to cointegration approach. The key findings are that oil revenues and public investment contributes to Nigeria’s economic growth. However, our findings also indicate that external debt and population growth retards growth. The study suggests that minimizing fiscal deficits and unnecessarily foreign loans by creating tax avenues through the development of the non-oil sectors would reduce the dependency syndrome on a single commodity (oil) in Nigeria.

This study aimed to investigate the impact of incorporating Refuse Derived Fuel (RDF) into a production brick mixture in order to mitigate difficulties encountered in the production environment. Three distinct tests were conducted to assess the preparation process. The first test served as a reference, utilizing 100% clay material without RDF. The second test involved the inclusion of 10% RDF, obtained from a waste factory, with a grain size less than 20mm. In the third test, the RDF was mixed with silica sand after undergoing hammer milling with a 2mm sieve, followed by a 10% incorporation into the mixture. The primary objective was to comprehend the behavior of these mixtures in two critical stages: extrusion and drying. Extrusion performance was evaluated by examining the shaping process from the mold, vacuum conditions within the extruder, and the cutting of wet sample bricks. Furthermore, the drying procedure was assessed in terms of shrinkage, drying sensitivity, and appearance. Comparisons were made among the three test scenarios to identify the influence of RDF on these key parameters. Preliminary results indicate that the inclusion of RDF impacted the extrusion process. The addition of RDF resulted in variations in the flow characteristics of the mixture, affecting the shape formation from the mold and the vacuum conditions within the extruder. Additionally, the cutting of wet sample bricks exhibited some differences compared to the reference test. Concerning the drying phase, the presence of RDF influenced shrinkage behavior and drying sensitivity. The mixture with RDF showed different shrinkage patterns compared to the reference, and its drying sensitivity was altered. Moreover, the appearance of the bricks after drying exhibited notable variations due to the incorporation of RDF. In conclusion, incorporating RDF in the brick mixture introduces changes in both the extrusion and drying stages. The alteration in flow characteristics and vacuum conditions during extrusion, as well as the variations in shrinkage, drying sensitivity, and appearance during drying, suggest that further investigation is necessary to optimize the incorporation of RDF for improved brick production. These findings contribute to the understanding of the challenges and opportunities associated with the utilization of RDF in brick manufacturing processes.

The flower of Syringa pubescens Turcz. is a Chinese folk medicine and also used as flower tea for healthcare. The effects of five drying methods on the active compound contents, the antioxidant abilities, anti-inflammatory properties and enzyme inhibitory activities were evaluated. The plant materials were treated using shade-drying, microwave drying, sun-drying, infrared drying and oven drying. The seven active compounds were simultaneously determined by an HPLC method. Furthermore, the chemicals differences were assessed using Scanning electron microscopy, UV spectroscopy and infrared spectroscopy. The antioxidant capacities and protective effects on L02 cells induced by hydrogen peroxide were measured. The anti-inflammatory effects on lipopolysaccharide-induced RAW264.7 cells were investigated. The enzyme inhibitory activities were determined against α-amylase, α-glucosidase cholinesterases and tyrosinase. The results indicated that drying methods had significantly influences on the active compound contents and biological properties. In consideration of the contents of bioactive compound, the suitable drying methods were SHD, SD, OD and MD. The SHD sample exhibited stronger radical scavenging ability on DPPH, ABTS, hydroxyl and superoxide anions and higher reducing power compared with other samples prepared by SD, OD, MD and IRD. Moreover, SHD sample had strong protective effects against L02 cells damage induced by H2O2. SPF samples, especially SHD sample, significantly inhibited inflammatory factor secretion in LPS-stimulated RAW 264.7 cell. All studied SPF sample exhibited evidently inhibitory effects on the four enzymes. SHD sample possessed the highest inhibitory activity on α-glucosidase and α-amylase. While SHD and SD samples had the potential inhibitory effects on cholinesterases and tyrosinase. In consideration of active compound contents and biological activities, it was recommended that SHD and SD were applied for drying SPF at an industrial scale.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

Drying grains in a fixed bed can be an interesting alternative to prevent undesirable breaks and fractures of solids due to mechanical shocks, something that cannot be avoided when drying in moving beds. A disadvantage of fixed bed drying is that there can be significant gradients in the critical variables if the layer of particulate solids is thick. This work shows that periodically changing the direction of drying air flow is an effective technique to reduce differences within the bed and allow better uniformity of the product. Drying in a thick layer of 10 cm of sorghum grains was carried out at 50 and 60oC for air flow velocity of 2.1 m.s-1. The results showed that despite increasing the total drying time, the technique actually allowed a significant decrease in the temperature gradients and moisture content of the sorghum grains. The change in direction of the air flow caused the drying front to be displaced, sometimes towards the top, sometimes towards the base of the bed. At 50oC, drying lasted a total of 240 min, bringing the sorghum grains to an average overall moisture content of 0.13 on a dry basis.

Rice provides ~20% of human dietary energy and, for many people, a similar share of their protein. Rice cultivation, however, produces significant greenhouse gas (GHG) emissions, comparable to those from the aviation sector. The main GHG from rice production is methane, mostly a result of conventional rice cultivation (CRC) keeping rice fields continuously flooded during the crop cycle. There is extensive evidence that alternate wetting and drying (AWD) of rice fields substantially reduces methane emissions. AWD is one component of the System of Rice Intensification (SRI), an agroecological approach to the management of plants, water, soil and nutrients practiced by millions of farmers in both lowland irrigated rice and upland rainfed cultivation. Thirteen countries have included SRI in their Nationally Determined Contributions to GHG reduction or climate change mitigation. This article reviews 16 field studies of the net reduction in GHG emissions from the adoption of AWD, eight from the adoption of SRI, and two that compared SRI and AWD. Where available, the review includes data on yield and therefore on carbon dioxide-equivalent GHG emissions per kilogram of rice produced. The evidence indicates that AWD and SRI offer a similar and substantial reduction (~35–41%) in GHG emissions per hectare compared with conventional rice cultivation. However, SRI offers ~66% greater yield than CRC, and therefore greater reduction in emissions per kilogram of rice, ~54% more than AWD. The limited data directly comparing SRI and AWD support this finding. SRI also appears to have greater potential to sequester carbon in the soil. SRI lowers rice farmers’ costs of production, adds to their income and can make climate-friendly methods more attractive. Both AWD and SRI are greatly preferable to current conventional practices, but SRI offers opportunities to contribute to food security while directly addressing the drivers of climate change.

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties so that it can be used in human body. This research explores the use of binder jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted and processing parameters were varied to study their effect on the printing of this biocomposite. Layer thickness, binder saturation and drying time affected the dimensional tolerance and the density of the green samples. This effect is important to understand so that the material can be optimized for use in specific applications.

Porous β-tricalcium phosphate (Ca3(PO4)2; β-TCP) was prepared by freeze-drying and the effects of this process on pore shapes and sizes were investigated. Various samples were prepared by freezing β-TCP slurries above a liquid nitrogen surface at −180 °C with subsequent immersion in liquid nitrogen at −196 °C. These materials were then dried under reduced pressure in a freeze-dryer after which they were sintered by heating. Compared with conventional heat-based drying, the resulting pores were more spherical, which increased both the mechanical strength and porosity of the β-TCP. These materials had a wide range of pore sizes from 50 to 200 µm, with the mean and median values both approximately 100 µm regardless of the freeze-drying conditions. Mercury porosimetry data showed that the samples contained small, interconnected pores with sizes of up to 1.24 µm and macroscopic, interconnected pores up to 25.8 µm in size. The effects of non-ionic surfactants having different hydrophilic/lipophilic balance (HLB) values on foaming and pore size were also investigated. Materials made with surfactants having lower HLB values exhibited smaller pores and lower porosity whereas higher HLB surfactants gave higher porosity and slightly larger macropores. Even so, the pore diameter could not be readily controlled solely by adjusting the HLB value. The findings of this work indicated that high porosity (75%) and good compressive strength (&gt;2 MPa) can both be obtained in the same porous material and that foaming agents with HLB values between 12.0 and 13.5 were optimal.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

The microscopic pore structure of tight sandstone reservoir significantly influences the characteris-tics of CO2 flooding after water flooding. The research was conducted using various techniques such as casting thin sections, high pressure mercury injection, scanning electron microscopy, Nu-clear magnetic resonance (NMR) testing, and a self-designed high-temperatures and high-pressures microscopic visualization displacement system. Three type cores with different pore structures were selected for the flooding experiments and the microscopic visualization displace-ment experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flood-ing after the conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show that: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In the CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples was primarily from large pores, however, the oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic re-sidual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery of near-miscible flooding after water flooding regarding the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding about type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil grad-ually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

Background Oil palm (OP), Elaeis guineensis , is by far the most important global oil crop, supplying about 40% of total traded vegetable oil. Palm oils are key dietary components consumed daily by over three billion people, mostly in Asia, and also have a wide range of important non-food uses including in cleansing and sanitising products. Main body Oil palm is a perennial crop with a >25-year life cycle and an exceptionally small land footprint compared to annual oilseed crops. Oil palm crops globally produce an annual 81 million tonnes (Mt) of oil from about 19 million hectares (Mha). In contrast, the second and third largest vegetable oil crops, soybean and rapeseed, yield a combined 84 Mt oil but occupy over 163 Mha of increasingly scarce arable land. Despite this advantage, oil palm has acquired a poor environmental reputation, especially in Europe and North America, although soybean planting is now responsible for more deforestation. Oil palm crops face other challenges in the 2020s. On the demand side, these include changing consumer purchasing habits, threats to global trade systems, and diminishing demand for liquid fuels as transport systems become increasingly electrified. On the supply side, major issues include stagnant yields in ageing plantations, sluggish replanting of improved varieties, labour shortages, diseases and climatic/ environmental threats. The latter include the increasing incidence of new and existing pests/diseases and a general lack of climatic resilience, especially relating to elevated temperatures and increasingly erratic rainfall patterns. This review surveys the oil palm sector in the 2020s and beyond, its major challenges and options for future progress. Conclusions Oil palm crops face many future challenges, including emerging threats from climate change and new pests and diseases, that require more effective international collaboration. Nevertheless, new breeding technologies are providing the promise of improvements, such as much higher yielding varieties, improved oil profiles, enhanced disease resistance and modified crop architecture to enable harvesting mechanisation. The industry also needs to redouble its efforts to engage with global consumers in a constructive dialogue aimed at addressing its image problem and explaining the many benefits of its products.

The prominent cultivation of lemongrass relies on the pharmacological incentives of its essential oil. The lemongrass essential oil (LEO) has a significant amount of citral (mixture of geranial and neral), isoneral, isogeranial, geraniol, geranyl acetate, citronellal, citronellol, germacrene-D, and elemol in addition to numerous other bioactive compounds. These components confer various medicinal activities to LEO including antifungal, antibacterial, antiviral, anticancer, and antioxidant properties. These attributes are commercially exploited in pharmaceutical, cosmetics, and food preservations industries. Furthermore, the employment of LEO in the treatment of cancer opens a new vista in the field of therapeutics. Although different LEO components have shown promising anticancer activities in vitro, these effects have not been assessed yet in humans. Further studies on the anticancer mechanisms exerted by lemongrass components are required. The present review intends to provide a timely discussion on the relevance of lemongrass extracts in cancer and health treatment, and in food industry applications.

This study was focused on the development of oil-producing microorganisms to generate lipids. The yeast Rhodotorula mucilaginosa (R. mucilaginosa) was selected for liquid-state cultivation, and the conditions for growth of the yeast cells were assessed. Additionally, the relationships between different nutrient elements and the growth of R. mucilaginosa were explored. The lipid accumulation of R. mucilaginosa is increased under nitrogen-restricted conditions. As the concentration of the carbon source increases, the accumulation of lipids is increased. However, if the carbon source concentration is further increased, the growth of yeast is inhibited. From a large-scale liquid fermentation culture with a fixed inoculation amount of 5%, and from a batch of culture experiments, it was determined that a suitable oil-producing culture was obtained on the 6th day, and the optimum conditions involved a carbon source concentration of 60 g/L, a nitrogen source concentration of 0.5 g/L, and a KH2PO4 concentration of 7.0 g/L. After utilizing different carbon sources in this study, it was found that glucose was the carbon source most conducive to the accumulation of R. mucilaginosa lipids. In addition, the extraction method and solvent for the extraction of R. mucilaginosa lipids were chosen. The acid-heat method using the green organic solvent ethyl acetate exhibited the best performance for extraction of yeast lipids under environmentally friendly and safe conditions. The analysis of lipids showed that the fatty acids obtained primarily contained C16:0, C18:1 and C18:2, and especially C18:1 (41%) lipids, indicating that R. mucilaginosa lipids are a good bio-oil source for the production of biodiesel.

Freeze-drying is a well-established process in biomedical engineering for the fabrication of three-dimensional open-porous medical devices, especially those based on biopolymers. One of the most used biopolymers in this field is collagen, the most abundant protein in the human body and the main component of the extracellular-matrix, as well as its derivatives. Freeze-dried collagen-based sponges with a wide variety of attributes can be produced by design and have led to a wide range of successful commercial medical devices, foremost for dental, orthopedic, hemostatic and neuronal applications. However, this is still considered a high-cost and time-consuming process that is often used in a non-optimized manner. By combining advances in other technological fields, the opportunity arises to further evolve this process in a sustainable manner, and optimize the resulting products as well as create new opportunities in this field.

This paper addresses the atmospheric emissions from oil and gas extraction and production in Greece. The study was carried out in 2014 in the Kavala gulf, which currently is the only location of oil and gas production in Greece and where the exploration activities for hydrocarbons started in the late ‘60’s. This study presents the qualitative and quantitative characteristics of atmospheric emissions, in relation also to the emissions’ control management system. Particular reference is made to sulphur compounds since the existence of volcanic rocks results to increased amounts of H₂S. The results shows that, currently, atmospheric emissions of pollutants during extraction and production of hydrocarbons in Greece are very low and do not have any significant effect on air quality and climate change. Since it is expected that exploitation of hydrocarbons and oil and gas extraction and production will increase in the future, appropriate measures should be taken to ensure environmental protection, such as the development of integrated monitoring systems and the use of up to date emission control technologies.

In dry season paddy farming, the alternate wetting and drying (AWD) irrigation improves water productivity, paddy production, and has the potential to decrease greenhouse gas (GHG) such as methane (CH4) and nitrous oxide (N2O) emissions when compared to continuous flooding (CF). However, there is a lack of research in Bangladesh on the effects of water management on CH4 and N2O emissions. During November 2017–April 2018, participatory on-farm trials were conducted at Feni and Chattogram districts of Bangladesh. Total 105 farmers comprising 20-hectare of land (62 farmers at Feni and 43 farmers at Chattogram district, each location having 10 hectare of land). We compared irrigation water and cost reductions, paddy yield, and CH4 and N2O emissions from paddy fields irrigated using AWD and CF irrigation methods. The CH4 and N2O emissions were determined using the Cool Farm Beta-3 methodology, and the global warming potential (GWP) was estimated using the Intergovernmental Panel on Climate Change-2014 standard approach. The mean results of randomly selected 30 farmers from two locations (15 of each) showed that AWD remarkably decreased irrigation water consumption by about 24% and increased water productivity by 224%. We estimated 23% savings for irrigation costs in AWD. By this time, AWD improved paddy production by 3% over CF. The AWD irrigation resulted in a 47% reduction in cumulative CH4 emissions having a lower CH4 emission factor (0.74 kg ha-1 day-1) than CF (1.39 kg ha-1 day-1). There was no obvious difference in N2O emission between AWD and CF. When compared to CF, AWD decreased the overall GWP by 27% and lowered the GHG intensity by 42%. The CH4 and N2O emissions did not differ substantially between Feni and Chattogram.

Sustainable development can only be realised when the social, economic and environmental dimensions are considered altogether. Social capital and local wisdom offer important contributions to the development process and the capabilities of individuals and groups as development actors. This study analyses the role of social capital and local wisdom in managing business partnerships between farmers and palm oil plantation companies in North Konawe, Indonesia. Data were collected via in-depth interviews, field observations and focus group discussions and were analysed descriptively and qualitatively. Results underscore the importance of social capital and local wisdom in organising institutional programmes for strengthening palm oil business partnerships. Trust, social networks and participation negatively affect the sustainability of these partnerships, whilst local wisdom and social solidarity positively influence institutional strengthening. Inconsistency and lack of openness by companies can lead to a trust crisis that can threaten the sustainable operations of palm oil companies. Building a good cooperative commitment and maintaining collaboration play key roles in enhancing community welfare and increasing company profits. The social capital and local wisdom of farmer institutions in villages are expected to significantly contribute to the establishment of sustainable palm oil business partnerships.

This study investigates the impact of General Government Final Consumption Expenditure (GC) on GDP growth in Saudi Arabia during major economic crises from 1990 to 2022, focusing on periods marked by fluctuations in oil and non-oil revenues. By integrating these revenue streams, the research provides a more comprehensive analysis of fiscal policy effectiveness during economic downturns. Using an Autoregressive Distributed Lag (ARDL) model, the study reveals that Government Consumption significantly stabilizes and stimulates the Saudi economy amidst revenue volatility. Key findings highlight the dual role of Government Consumption (GC) as both a buffer against immediate economic shocks and a stimulus for economic recovery. The study contributes to the discourse on fiscal policy in oil-dependent economies by demonstrating the critical role of diversified revenue strategies in enhancing economic resilience. Recommendations are offered for policymakers to optimize fiscal strategies, ensuring robust economic recovery and long-term stability in volatile markets. This research underscores the necessity for Saudi Arabia to refine its fiscal policies towards greater economic diversification and stability.

This work is aimed at promoting a healthier means of livelihood by investigating insignificant areas of pollution. In this work, soy candles produced from soybeans were proven as healthier alternatives to paraffin candles. Soxhlet extraction method was used with hexane as solvent. The extracted oil were then solidified. The wax was moulded into candle and tests were carried out to prove its claims as a safer alternative to paraffin wax. The results supported this claims that soy candles is more economical and produced lesser soot than the paraffin candles.

Enhancing the management and monitoring of oil and gas processes demands developing precise predictive analytics techniques. Over the past two years, oil and its prediction have advanced significantly using conventional and modern Machine Learning techniques. Several review articles detail the developments in predictive maintenance and technical and non-technical aspects of influencing the uptake of big data. The absence of references for machine learning techniques impacts the effective optimization of predictive analytics in the oil and gas sector. This review paper offers readers thorough information on the latest machine learning methods utilized in this industry's predictive analytical modelling. The review covers forms of Machine Learning techniques used in predictive analytic modelling from 2021 to 2023 (91 articles). It provides an overview of the details of the papers that were reviewed, comprising of the model’s categories, the data's temporality, field, and name, the dataset's type, predictive analytics (classification or clustering or prediction), the models' input and output parameters, performance metrics, optimal model, and benefits and its drawbacks. Additionally, suggestions for future research directions are provided to raise the potential of the associated knowledge and increase the accuracy of oil and gas predictive analytics models.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

This study explores the development of an oil-in-water (O/W) emulsion with a high concentration of ostrich oil, rich in omega-3, -6, and -9 fatty acids, for potential skincare applications. Utilizing Span and Tween emulsifiers, an optimized O/W emulsion containing 20% w/w ostrich oil and 15% w/w mixed emulsifiers was formulated through homogenization, demonstrating the smallest droplet size (5.01 ± 0.43 μm) and appropriate zeta potential (-32.22 mV). The emulsion exhibited antioxidant and antibacterial properties against Staphylococcus aureus, suggesting its suitability for skincare. Stability tests over 6 months at varying temperatures (4 °C, 25 °C, 45 °C) confirmed the emulsion's physical and microbial stability, emphasizing its potential for topical applications. Despite slight changes in acid values (AV) and peroxide values (PV), results remained within acceptable limits. Cytotoxicity assessments on human dermal fibroblasts indicated the emulsion's safety, supporting its suitability for skin application. The emulsion demonstrated antibacterial efficacy against S. aureus and enhanced antioxidant activity compared to ostrich oil alone. The study underscores the importance of emulsification in optimizing the efficacy and stability of ostrich oil in skincare formulations, offering valuable insights for practical applications where stability is critical.

This paper presents a review of the electrical heating method for heavy oil recovery based on past, current, and future prospects of electrical heating. Heavy oil is one of the potential crude oil used as a link to reduce the crisis of light oil used today. The obstacle of heavy oil is a high viscosity and density in which thermal injection is a method for heavy oil recovery, but it results in economic and environmental issues. Electrical heating is one of the thermal methods by transferring heat into the reservoir. The basic process of electrical heating is to increase the mobility of the oil. Because the temperature rises, it can reduce oil viscosity and makes it easier for heavy oil to flow. The past and current developments have been carried out to fill up the gap of electrical heating projects. The future prospects must meet energy efficiency, and the excessive heat will damage formation that must be tackled in the future prospect. the works adopt several electrical heating projects and applications in the world where the works give a brief future prospect of electrical heating.

Lifestyle is the primary prevention of diabetes, especially type-2 diabetes (T2D). Nutritional intake of olive oil (OO), the key Mediterranean diet component has been associated with the prevention and management of many chronic diseases including T2D. Several OO bioactive compounds such as monounsaturated fatty acids, and key polyphenols including hydroxytyrosol and oleuropein, have been associated with preventing inflammation and cytokine-induced oxidative damage, glucose lowering, reducing carbohydrate absorption and increasing insulin sensitivity and related gene expression. However, research into the interaction of OO nutraceuticals with lifestyle components, especially physical activity is lacking. Promising postprandial effects have been reported when OO or other similar monounsaturated fatty acids was the main dietary fat compared with other diets. Animal studies have shown a potential anabolic effect of oleuropein. Such effects could be further potentiated via exercise, especially strength training, which is an essential exercise prescription for individuals with T2D. There is also an evidence from in vitro, animal and limited human studies for a dual preventative role of OO polyphenols in diabetes and cancer, especially that they share similar risk factors. Putative anti-oxidative and anti-inflammatory mechanisms and associated gene expressions resulting from OO phenolics, have produced paradoxical results making suggested inferences from dual prevention T2D and cancer outcomes difficult. Well-designed human interventions and clinical trials are needed to decipher such a potential dual anti-cancer and anti-diabetic effects of OO nutraceuticals. Exercise combined with OO consumption, individually or as part of a healthy diet is likely to induce reciprocal action for T2D prevention outcomes.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

This paper presents tea leaves moisture monitoring system based on RF reflectometry techniques. The system was divided into two parts which are the sensor and reflectometer parts. The large coaxial probe was used as a sensor of the system. The reflectometer part plays a role as signal generator and also data acquisition. The reflectometer-sensor system was operated with a graphical user interface at 1.529 GHz at room temperature. The system was able to measure the moisture content of tea leaves ranging 0% m.c to 50% m.c on a wet basis. In this study, up to five kinds of tea leaves bulk were tested. The mean of absolute errors in the moisture measurement for tea leaves was ±2.

Surface area and pore size distribution of Eucalyptus samples pretreated by different methods were determined by the Brunauer-Emmett-Teller (BET) technique. Three methods were applied to prepare cellulosic biomass samples for BET measurements: air, freeze, and critical point drying (CPD). Air and freeze drying caused severe collapse of biomass pore structures, but CPD effectively preserved biomass morphology. Surface area of CPD prepared Eucalyptus samples was determined to be 58–161 m2/g, whereas air and freeze dried samples were 0.5–1.3 and 1.0–2.4 m2/g, respectively. Average pore diameter of CPD prepared Eucalyptus samples were 61–70Å. CPD preserved Eucalyptus sample morphology by replacing water with a non-polar solvent, CO2 fluid, which prevented hydrogen bond reformation in the cellulose.