The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

This paper proposes a single-stage asymmetrical half-bridge fly-back (AHBF) converter with resonant mode using dual-mode control. The presented converter has an integrated boost converter and asymmetrical half-bridge fly-back converter and operates in resonant mode. The boost-cell always operates in discontinuous conduction mode (DCM) to achieve high power factor. The presented converter operates simultaneously using a variable-frequency-controller (VFC) and pulse-width-modulation (PWM) controller. Unlike the conventional single-stage design, the intermediate bus voltage of this controller can be regulated depending on the main power switch duty ratio. The asymmetrical half-bridge fly-back converter utilizes a variable switching frequency controller to achieve the output voltage regulation. The asymmetrical half-bridge fly-back converter can achieve zero-voltage-switching (ZVS) operation and significantly reduce the switching losses. Detailed analysis and design of this single-stage asymmetrical half-bridge fly-back converter with resonant mode is described. A wide AC input voltage ranging from 90 to 264 Vrms and output 19 V/ 120 W prototype converter was built to verify the theoretical analysis and performance of the presented converter.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

In modern inverter applications, multilevel converters are used thanks to their capability of reducing the passive fi lter volumes, improving the overall THD, sharing the power sources across the several converter cells, and providing a reconfi guration ability in case of failure. However, increasing the number of cells makes more complex the control of the converter. This article proposes a decentralized control technique based on the use of elementary modular controllers, associated with each converter cell and communicating with their close neighbors to obtain the balancing of the powers they supplied. Each modular controller can be dynamically removed or added to allow reconfi guration of the converter for functional safety purpose. This method is applied to a 240V/3A 5-cells Cascaded Full-Bridge Multilevel Converter. The response of the system to load transients and cell voltage disturbances demonstrates the robustness of the proposed decentralized control method. Thanks to the use of modular controllers, the number of levels of the converter can be extended to the order N without adding complexity to its control.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

Sugar-sweetened beverages are associated with metabolic dysfunction, particularly in those with increased risk factors. Artificial sweeteners (AS) are often promoted as a healthier alternative, yet findings remain conflicting as to their effects on metabolic function. Further, there is a lack of data exploring the interaction between AS and high-fat diets (HFD). We therefore examined the effects of HFD and the AS Acesulfame-potassium (Ace-K) on glucose intolerance and adipose tissue physiology in male and female C57BL/6 mice. 40 mice were randomised to receive either a) a control diet (CDCon; standard control diet/water), b) control diet and Ace-k (CDAS; CD/7.5mM AS in drinking water), c) HFD (HFCon; HFD (45%kcal from fat)/water), or d) HF and AS (HFAS; HFD/7.5mM AS in drinking water) for 6 weeks. A HFD increased body weight in male and female mice independently of AS supplementation. AS induced sex-specific effects protecting against HFD-induced hyperglycaemia and adipocyte hypertrophy in male mice and reducing inflammatory gene expression in the adipose tissue. Conversely in females, AS induced hyperinsulinemia in HFD mice and increased expression of immune-related genes. These findings suggest that supplementation of HFD with AS exacerbates metabolic dysfunction in female mice. This work supports the importance of studying sexually dimorphic responses to an altered nutritional environment and highlights the need for further investigation into the intake of AS, particularly in those already at risk of metabolic disease such as the obese or overweight.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Electromagnetic interference (EMI) generated by switching operations within high voltage DC (HVDC) converter stations is an issue that has been addressed by CIGRE and methods to manage EMI should be considered in the design phase using electromagnetic modeling techniques. It is shown that method of moments-based techniques that have been used in many previous studies may not be sufficient. Here, the finite-difference time-domain method is used to study the properties of single switching events using a realistic model of an HVDC converter station with special emphasis on determining the impact of the valve hall on shielding EMI. It is shown that the valve hall does not confine high frequency electromagnetic fields to the valve hall; rather it delays them from exiting through bushings in the wall. Further, it is shown that incorporating electromagnetic absorbing material into the valve hall design can significantly reduce EMI outside the converter station.

In this paper, the active front-end (AFE) converter topology for the total harmonic distortion (THD) reduction in a wind energy system (WES) is used. A higher THD results in serious pulsations in the wind turbine (WT) output power and in several power losses at the WES. The AFE converter topology improves capability, efficiency and reliability in the energy conversion devices; by modifying a conventional back-to-back converter, from using a single voltage source converter (VSC) to use pVSC connected in parallel the AFE converter is generated. The THD reduction is done by applying a different phase shift angle at the carrier of digital sinusoidal pulse width modulation (DSPWM) switching signals of each VSC. To verify the functionality of the proposed methodology, the WES simulation in Matlab-Simulink® is analyzed, and the experimental laboratory tests using the concept of rapid control prototyping and the real-time simulator Opal-RT® Technologies is achieved. The obtained results show a type-4 WT with total output power of 6MVA, generating a THD reduction up to 5.5 times at the WES.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

The foot-mounted inertial navigation system is an important application of pedestrian navigation as it in principle does not rely any external assistance. A real-time range decomposition constraint method is proposed in this paper to combine the information of dual foot-mounted inertial navigation systems. It is well known that low-cost inertial sensors with ZUPT (zero-velocity update) and range decomposition constraint perform better than in either single way. This paper recommends that the distance of separation between the position estimates of feet-mounted inertial navigation systems be restricted in the ellipsoidal constraint which relates to the maximum step and leg height. The performance of the proposed method is studied utilizing experimental data. The results indicate that the method can effectively correct the dual navigation systems’ position over the existing spherical constraint.

1) Background: Several studies have shown the benefit of drawing when learning anatomy. Virtual Reality (VR) also appears to be useful to increase the understanding of the location of anatomical structures. This study aims to describe how students in an Operating Room Nursing (OR nursing) master study program perceive the benefit of active learning methods, including drawing and the use of VR. 2) Methods: We combined these two methods in a class of 29 students. 38 half-finished drawings of anatomical structures were made. The students were to complete these during lectures with guidance from the teacher. The students also attended a two-hour VR session where they were to find various anatomical structures. A paper questionnaire was applied to evaluate the teaching program. Data were analyzed statistically. 3) Results: The students highly appreciated these learning methods. They reported that drawing made them work more actively during lectures and increased their learning outcome. They also perceived that the use of VR technology increased their understanding of the location of anatomical structures. 4) Conclusion: The combination of drawing and VR technology may be of benefit to OR Nursing students when learning anatomy by both increasing student activity and learning outcomes.

(1) Background: The rapid expansion of 4G and 5G networks has raised public concerns about potential health risks associated with electromagnetic radiation. This study addresses these fears by investigating electromagnetic measurements in crowded squares, where human exposure is heightened. Despite rigorous scientific methodologies showing generally low levels of radiation from these technologies, public apprehension persists; (2) Methods: We conducted 496 measurements in Larissa's major squares, using a portable field strength analyzer and GIS mapping. Squares were categorized by traffic and population density; (3) Results: Low-traffic squares exhibited exposure ratios consistently below ICNIRP limits, with median values of 0.0012 and 0.00173 in non-active and active mobile phone cases, respectively. In high-traffic squares, the median exposure ratio was 0.00335 in non-active mobile phone cases, remaining below recommended limits; (4) Conclusions: These findings indicate no significant risk of electromagnetic radiation in crowded squares in Larissa, emphasizing the importance of factual communication and dispelling public misconceptions.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Chronic kidney disease (CKD) and cardiovascular disease (CVD) are highly prevalent conditions, each significantly contributing to the global burden of morbidity and mortality. CVD and CKD share a great number of common risk factor, such as hypertension, diabetes, obesity, and smoking among others. Their relationship extends beyond these factors, encompassing intricate interplay between the two systems. Within this complex network of pathophysiological processes, vitamin D has emerged as a potential linchpin, exerting influence over diverse physiological pathways implicated in both CKD and CVD. In recent years, scientific exploration has unveiled a close connection between these two prevalent conditions and vitamin D, a crucial hormone traditionally recognized for its role in bone health. This article aims to provide an extensive review of vitamin D's multifaceted and expanding actions concerning its involvement in CKD and CVD.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

This paper presents a wideband dual-polarized dipole antenna structure operating at 1.7-3.8 GHz (76.4%). For a traditional 4G dipole antenna which covers the band 1.71 GHz- 2.69 GHz, it’s difficult to maintain the satisfactory impedance matching and normal stable radiation patterns within the 5G sub-6 GHz band 3.3-3.8 GHz, which mainly due to the fixed antenna height is no longer a quarter-wavelength. To solve this, a connected-ring-shaped metasurface structure is proposed and deployed to operate as an artificial magnetic conductor (AMC). As a result, stable antenna radiation patterns are obtained within the whole band 1.7-3.8 GHz. For verification, this wideband dipole antenna using AMC is implemented and tested. The measured results show that the proposed antenna has an impedance bandwidth of 80.7% (1.7-4.0 GHz). It has an average measured in-band realized gain of 7.0±1.0 dBi and a stable 70∘±5∘ half power beam width (HPBW) within the 4G/5G-sub 6GHz bands 1710-2690 MHz and 3300-3800 MHz.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

This research presents the design and characteristics of new wideband polarizer based on the square waveguide with irises. Matching and polarization characteristics of the polarizer have been simulated and optimized. Frequency dependences of the characteristics are presented. Developed polarizer can be applied in satellite information systems.

Retinal vein cannulation involves puncturing an occluded vessel on the micron scale. Even single millinewton force can cause permanent damage. An ophthalmic robot with a piezo-driven injector is precious enough to perform this delicate procedure, but the uncertain viscoelastic characteristics of the vessel makes it difficult to achieve the desired contact force without harming the retina. The paper utilizes a viscoelastic contact model to explain the mechanical characteristics of retinal blood vessels in order to tackle this issue. The uncertainty in the viscoelastic properties is considered an internal disturbance of the contact model, and an active disturbance rejection controller is then proposed to precisely control the contact force. The experimental results show that this method can precisely adjust the contact force at the millinewton level even when the viscoelastic parameters vary significantly (up to 403.8%). The root mean square (RMS) and maximum value of steady-state error are 0.32 mN and 0.41 mN. The response time below 2.51 s with no obvious overshoot.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

In this paper we explore the known connection among sustainability, resilience, and well-being within the framework of active inference. Initially, we revisit how the notions of well-being and resilience intersect within active inference before defining sustainability. We adopt a holistic concept of sustainability denoting the enduring capacity to meet needs over time without depleting crucial resources. It extends beyond material wealth to encompass community networks, labor, and knowledge. Using the Free Energy Principle, we can emphasize the role of fostering resource renewal, harmonious system-entity exchanges, and practices that encourage self-organization and resilience as pathways to achieving sustainability, both in an agent and in collectives. We start by connecting Active Inference with well-being, building on exsiting work. We then attempt to link resilience with sustainability, asserting that resilience alone is insufficient for sustainable outcomes. While crucial for absorbing shocks and stresses, resilience must be intrinsically linked with sustainability to ensure that adaptive capacities do not merely perpetuate existing vulnerabilities. Rather, it should facilitate transformative processes that address the root causes of unsustainability. Sustainability, therefore, must manifest across extended timescales and all system strata, from individual components to the broader system, to uphold ecological integrity, economic stability, and social well-being. We explain how sustainability manifests at the level of an agent, and then at the level of collectives and systems. To model and quantify the interdependencies between resources and their impact on overall system sustainability, we introduce the application of network theory and dynamical systems theory. We emphasize the optimization of precision or learning rates through the active inference framework, advocating for an approach that fosters the elastic and plastic resilience necessary for long-term sustainability and abundance.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

New furan, thiophene and triazole oximes were synthesized through several-step reaction paths to investigate their potential for development of central nervous systems (CNS)-active and cholinesterase-targeted therapeutics in organophosphorus compound (OP) poisonings. Acute OP poisoning is still a challenge in treating patients despite the development of a large number of oxime compounds that should have the capacity to reactivate acetylcholinesterase (AChE) and butyrylcholinesterase (BChE). The activity of these two enzymes, crucial for neurotransmission, are blocked by the OP, which has the consequence of disturbing normal cholinergic nerve signal transduction in the peripheral and CNS, leading to cholinergic crisis. Oximes in use have one or two pyridinium rings and cross the brain–blood barrier poorly due to the quaternary nitrogen. Following our recent study on 2-thienostilbene oximes, in this paper we described the synthesis of 63 heterostilbene derivatives out of which 26 oximes were tested as inhibitors and reactivators of AChE and BChE inhibited by OP nerve agents – sarin and cyclosarin. While the majority of oximes were potent inhibitors of both enzymes in micromolar range, we identified several oximes as BChE or AChE selective inhibitors with a potential for drug development. Moreover, even oximes were poor reactivators of AChE, four heterocyclic derivatives reactivated the cyclosarin-inhibited BChE up to 70%, and cis,trans-5 [2-((Z)-2-(5-((E)-(hydroxyimino)methyl)thiophen-2-yl)vinyl)benzonitrile] had comparable reactivation efficacy to the standard oxime HI-6. In silico analysis and molecular docking studies connected the kinetic data to the structural features of these oximes, and confirmed their productive interactions with the active site of the cyclosarin-inhibited BChE. Based on inhibition and reactivation and their ADMET properties regarding lipophilicity, CNS activity, and hepatotoxicity, these compounds could be considered for further development of CNS-active reactivators in OP poisoning as well as cholinesterase-targeted therapeutics in neurodegenerative diseases like Alzheimer’s and Parkinson’s.

The objective of this paper is to present a mathematical formalism that states a bridge between Physics and Psychology, concretely between analytical dynamics and personality theory in order to open new insights in this theory. In this formalism energy plays a central role. First, the short-term personality dynamics can be measured by the General Factor of Personality (GFP) response to an arbitrary stimulus. This GFP dynamical response is modelled by a stimulus-response model: an integro-differential equation. The bridge between Physics and Psychology is provided when the stimulus-response model can be formulated as a linear second order differential equation and, subsequently, reformulated as a Newtonian equation. This bridge is strengthened when the Newtonian equation is derived from a minimum action principle, obtaining the current Lagrangian and Hamiltonian functions. However, the Hamiltonian is a non-conserved energy. Then, some changes provide a conserved Hamiltonian function: the Ermakov-Lewis energy. This energy is presented, as well as the GFP dynamical response that can be derived from it. An application case is presented: an experimental design in which 28 individuals consumed 26.51 g of alcohol. This experiment provides an ordinal scale for the Ermakov-Lewis energies that predicts the effect of a single dose of alcohol.

Energy harvesting is an emerging topic recently. This harvested energy is used to operate wireless sensors for different industrial monitoring and automation. To maximize the harvested energy in spinning systems, the harvester should vibrate at resonance for different spinning frequencies which can be achieved by active fitting. In this research, a novel methodology was developed by actively customizing the length of vibrating element beam to manipulate its natural frequency according to the spinning frequency. Different models were investigated numerically and experimentally to verify the proposed methodology. COMSOL Multiphysics software V5.1 was used to develop the numerical model, then and tip deformation and voltage difference results were benchmarked. The numerical model was verified experimentally by attaching a piezoelectric MIDE PPA 1021 which its vibrating length was varied by changing the supporting length from 0 mm to 12 mm to a spinning object having variable frequency from 0-200 Hz. It is found that the MIDE PPA 1021 beam vibrated at its resonance throughout the specified spinning frequencies. The proposed harvester can be applied in battery-free sensors being used in automotives, wind-mills blades, and rotating machinery.

In the last decade, a higher level of reliability became a compulsory demand when it comes to modern DC-DC converters. This work addresses the main reliability metrics: the failure rate λλ and MTBF of an output capacitor bank used within a high current low voltage buck converter due to many studies have shown that the output capacitor bank was demonstrated being the most critical component within the converter. Many authors treated this issue, usually by doing reliability predictions. The majority of the papers use only one specific Standard Prediction to solve the problem. Herein calculation was done using both the older standard MIL-HDBK-217 and the latest one Telcordia SR-332, providing a benchmark comparison between the two which is a helpful tool for the output capacitor selection in the early stage design. Military standard was well accepted for decades in order to reliability prediction even on industrial electronics and is still used today under a critical manner because no more update after the latest version MIL-HDBK-217F - Notice 2 released in 1995. Since then, newer prediction standards had appeared in the electronics reliability market. Over time, this standard was mostly used but it does not accurately model the reliability because lack of taking account of mission profile. The above-mentioned newer standard – i.e., Telcordia SR-332 is trying to compensate also the lack of the newest component technology in the older standard (which is the first standard released on the market) supplying useful design data for design engineers who use the so-called “design with the reliability in mind” concept. Within the paper were established the environmental condition for the passive components by means of a PoL (Point of load) buck converter that is used for both calculation methods. The influence of temperature and several specific concepts like reference conditions, operating conditions, ripple, and internal self-heating were taking account in order to display the results. The temperature for the capacitor’s capsule needed in π_T stress factor calculation was derived by PSPICE simulation. High fidelity and dedicated SPICE models provided by the manufacturer were used for MOSFETs, polymer electrolytic, and MLCC capacitors that compose the converter.

Student-centered active learning (SCAL) shifts the focus from the teacher to the student. Implementing SCAL requires the development of new forms of assessment beyond memorization and comprehension. This paper aims to demonstrate the effectiveness of SCAL by analyzing student performance at different cognitive levels. In flipped classrooms, students completed tasks with varying cognitive demands. The tests measured knowledge (level 1), comprehension (level 2), application (level 3) and analysis (level 4). This approach to assessment assesses not only the acquisition of content, but also skills that are critical to a health science student's future career. The results of expository learning were compared with student-centered collaborative learning in the Anatomy and Embryology I course over three academic years. Student opinions were collected through 326 anonymous Wooclap® surveys. No differences in performance were found for low cognitive level questions. However, SCAL significantly improved performance on higher cognitive level questions that required problem solving and application of knowledge. Despite the benefits of SCAL, it requires more effort from both teachers and students. The current assessment system, which measures the quality of teaching, penalizes this effort and requires teachers to believe strongly in the effectiveness of SCAL.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

Durability monitoring of insecticide-treated nets (ITNs) containing a pyrethroid in combination with a second active ingredient (AI) must be adapted so that the insecticidal bioefficacy of each AI can be monitored independently. An effective way to do this is to measure rapid knock down of a pyrethroid-susceptible strain of mosquitoes to assess the bioefficacy of the pyrethroid component and to use a pyrethroid-resistant strain to measure the bioefficacy of the second ingredient. To allow robust comparison of results across tests within and between test facilities, and over time, protocols for bioefficacy testing must include either characterisation of the resistant strain, standardisation of the mosquitoes used for bioassays, or a combination of the two. Through a series of virtual meetings, key stakeholders and practitioners explored different approaches to achieving these goals. Via an iterative process we decided on the preferred approach and produced a protocol consisting of characterising mosquitoes used for bioefficacy testing before and after a round of bioassays, for example at each time point in a durability monitoring study. We present the final protocol and justify our approach to establishing a standard methodology for durability monitoring of ITNs containing pyrethroid and a second AI.

Particulate organic carbon (POC) is a pivotal component within the marine carbon cycle, actively involved in diverse biogeochemical processes. This study focuses on Mediterranean as the research region, selecting the most influential factors from 47 potential ones influencing surface POC. Using geographic detector for factor identification, ten primary influencers were identified. Preliminarily optimized random forest (BRF), backpropagation neural network, adaptive boosting, and extreme gradient boosting were utilized to construct POC assessment models. Notably BRF exhibited superior performance in estimating the sea surface POC. Further optimization of RF using the tuneRanger R package resulted in R² of 0.868, mean squared error of 1.119 (mg/m³) ², and mean absolute error of 1.041 (mg/m³). Surface POC concentrations in the Mediterranean for May and June 2017 were estimated. Spatial distribution analysis unveiled higher concentrations in the west, lower in the east, higher in the north, lower in the south, with higher levels near the coast and lower far from the coast. Additionally, the study deliberated on the impact of human activities on surface POC in the Mediterranean. This research contributes a high-precision method for satellite retrieval of surface POC concentrations in the Mediterranean, thereby enriching the understanding of POC dynamics in the area.

New setting is introduced to study “closing numbers” and “super-closing numbers” as optimal-super-resolving number, optimal-super-coloring number and optimal-super-dominating number. In this way, some approaches are applied to get some sets from (Neutrosophic)n-SuperHyperGraph and after that, some ideas are applied to get different types of super-closing numbers which are called by optimal-super-resolving number, optimal-super-coloring number and optimal-super-dominating number. The notion of dual is another new idea which is covered by these notions and results. In the setting of dual, the set of super-vertices is exchanged with the set of super-edges. Thus these results and definitions hold in the setting of dual. Setting of neutrosophic n-SuperHyperGraph is used to get some examples and solutions for two applications which are proposed. Both setting of SuperHyperGraph and neutrosophic n-SuperHyperGraph are simultaneously studied but the results are about the setting of n-SuperHyperGraphs. Setting of neutrosophic n-SuperHyperGraph get some examples where neutrosophic hypergraphs as special case of neutrosophic n-SuperHyperGraph are used. The clarifications use neutrosophic n-SuperHyperGraph and theoretical study is to use n-SuperHyperGraph but these results are also applicable into neutrosophic n-SuperHyperGraph. Special usage from different attributes of neutrosophic n-SuperHyperGraph are appropriate to have open ways to pursue this study. Different types of procedures including optimal-super-set, and optimal-super-number alongside study on the family of (neutrosophic)n-SuperHyperGraph are proposed in this way, some results are obtained. General classes of (neutrosophic)n-SuperHyperGraph are used to obtains these closing numbers and super-closing numbers and the representatives of the optimal-super-coloring sets, optimal-super-dominating sets and optimal-super-resolving sets. Using colors to assign to the super-vertices of n-SuperHyperGraph and characterizing optimal-super-resolving sets and optimal-super-dominating sets are applied. Some questions and problems are posed concerning ways to do further studies on this topic. Using different ways of study on n-SuperHyperGraph to get new results about closing numbers and super-closing numbers alongside sets in the way that some closing numbers super-closing numbers get understandable perspective. Family of n-SuperHyperGraph are studied to investigate about the notions, super-resolving and super-coloring alongside super-dominating in n-SuperHyperGraph. In this way, sets of representatives of optimal-super-colors, optimal-super-resolving sets and optimal-super-dominating sets have key role. Optimal-super sets and optimal-super numbers have key points to get new results but in some cases, there are usages of sets and numbers instead of optimal-super ones. Simultaneously, three notions are applied into (neutrosophic)n-SuperHyperGraph to get sensible results about their structures. Basic familiarities with n-SuperHyperGraph theory and neutrosophic n-SuperHyperGraph theory are proposed for this article.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Nowadays, considering the growing tendency of companies towards e-commerce as well as green production, and dual-channel green supply chain management has become particularly important. This paper investigates pricing decisions within a dual-channel green supply chain framework while considering the capital constraints faced by risk-averse manufacturer. Simultaneously, the impact of the degree of risk aversion, consumer green preferences, and channel preferences on the optimal decision-making process of green supply chain members is analyzed. We address the issue of financial constraints faced by manufacturer through bank loans and trade credit financing and compare the two cases. Our findings illustrate that trade credit financing outperforms bank loan financing in the dual-channel green supply chain. Moreover, pricing decisions under different models are influenced by consumer preferences and risk aversion. Specifically, the greenness of the product, wholesale price, and sale price exhibit negative correlations with manufacturers' risk aversion but positive correlations with consumer preferences.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

Obesity is related to the establishment of chronic inflammation and metabolic diseases, but it can be positively influenced by the regular practice of physical activity. The study aimed to compare the anthropometric, metabolic, and inflammatory parameters of physically active Military Police Officers (MPOs) with those who are less physically active. Sixty male MPOs, low activity (n=28) and physically active (n=32) participated. The following parameters were measured: plasma cytokine levels, C-reactive protein (CRP) levels, circulating glucose triglyceride (TAG) and high-density lipoprotein cholesterol (HDL-C) levels, and plasma glutamic oxalacetate transaminase (GOT), glutamic-pyruvate transaminase (GPT), and gamma-glutamyl transferase (GGT) activities. The physically active group presented lower body fat and reduced TAG and IL-8 levels compared to the low activity group. Moreover, a negative correlation between SPE and SBP, DBP, BPM was detected for the physically active group (p<0.05) but not in the low activity group. Furthermore, the physically active group's work time (WT) values were not correlated with the important metabolic markers SBP, DBP, BPM, GLU, TAG (p>0.05) but could be in the low activity group (p<0.05). These findings highlight the fundamental protective role of physical activity in controlling body composition, subclinical inflammation, and cardiovascular risk in MPOs.

Daridorexant, as the first Dual Orexin Receptor Antagonist (DORA) marketed in Europe, offers a novel therapeutic approach to insomnia. However, data regarding its real-world safety are scarce. Thus, the aim of this study was to assess its safety profile using a large-scale pharma-covigilance database. Daridorexant-related Adverse Drug Reaction (ADR) reports from the FDA Adverse Event Reporting System were scrutinized, and ADRs were selected using reporting odds ratio (ROR) as a measure of disproportionality. Frequencies of events related to daridorexant were compared to all other drugs (reference group, RG1) and only to other DORAs (RG2). Only significant disproportionalities to both RGs were evaluated in-depth. A total of 845 dari-dorexant-related reports were selected; nightmares (n = 146; Dari vs. RG1: ROR = 113.74; 95%CI[95.13, 136]; Dari vs. RG2: ROR = 2.35; 95CI%[1.93, 2.85]), depression (n = 22; Dari vs. RG1: 2.13; [1.39, 3.25]; Dari vs. RG2: ROR = 2.31; 95CI%[1.45, 3.67]), and hangover (n = 20; Dari vs. RG1: ROR = 127.92; 95CI%[81.98, 199.62]; Dari vs. RG2: 3.38; [2.04, 5.61]) were considered as safety signals. These data provide valuable insights into the real-world safety profile of dari-dorexant, supporting the existence of safety signals related to nightmares, depression, and hang-over.

Models of subsurface structures are important for successful deposit exploration but are challenged by the need to integrate data from different geophysical methods. In the present study, we evaluated a method of joint inversion in which audio-magnetotelluric (AMT) and dual frequency induced polarization (DFIP) data sets are inverted simultaneously to produce a consistent 2D resistivity model to show a clear image of subsurface structures. To achieve the objectives, we conducted AMT and DFIP surveys first on the same survey line within the Dongjun lead-zinc deposit in inner Mongolia by developing 31 AMT survey sites with an interstation separation of 40 m on a 1440 m survey track and operated in fifty-three frequencies in the range 1–10,400 Hz to record the resistivity distribution of subsurface to depths exceeding 800 m. The same survey setup up was applied to the DFIP method by utilizing the SQ-3C model with a pole-dipole array configuration and conducted measurements at frequencies of 4 Hz and 4/13 Hz. We first separately inverted AMT and DFIP measurements. The two-dimensional (2D) model obtained from AMT data revealed distinct low resistivity anomalies in the middle of the 2D inversion model. In contrast, the DFIP inversion model showed a high resistive body in the same region. In response to the discrepancies observed in the separate 2D inversion models, we implemented a joint inversion for both the AMT and DFIP datasets. The joint inversion resistivity model shows surficial conducting bodies and a high conductive body along the profile with relatively high Percent Frequency Effect (PEF) indicating high chargeability. The final joint inversion resistivity model clearly images the large silica alteration zone and the Pb-Zn mineralization. This study demonstrates the feasibility of a joint inversion methodology and highlights the value of integrating geophysical methods through joint inversion for enhanced characterization and exploration of lead-zinc ores.

Although microgrids facilitate the increased penetration of distributed generations (DGs) and improve the security of power supplies, they have some issues that need to be better understood and addressed before realising the full potential of microgrids. This paper presents a comprehensive list of challenges and opportunities supported by a literature review on the evolution of converter-based microgrids. The discussion in this paper presented with a view to establishing microgrids as distinct from the existing distribution systems. This is accomplished by, firstly, describing the challenges and benefits of using DG units in a distribution network and then those of microgrid ones. Also, the definitions, classifications and characteristics of microgrids are summarised to provide a sound basis for novice researchers to undertake ongoing research on microgrids.

L-gulonolactone oxidase enzyme (GULO) catalyzes the last step of L-ascorbic acid (vitamin C) biosynthesis. This enzymatic activity is lost in primates. The full-length rat GULO has been previously produced in plants and demonstrated to be active. In this study, we compare activity of two variants of GULO produced in Escheriachia coli cells, full-length rat GULO (fGULO) and its C-terminal catalytic domain (cGULO). The expression and purification of the recombinant proteins were optimised and their biological activity was confirmed by two methods, the GULO activity assay in the protein extracts and the ‘in-gel’ staining for GULO activity. Both variants of recombinant GULO were biologically active in both assays. However, cGULO is more promising than fGULO for ascorbic acid production because it is more efficiently produced by bacteria.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p &lt; 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

The first Network Arch Bridge (NAB) was opened to traffic 60 years ago and since then the idea spread around the world. It is a type of a tied arch bridge that combines the benefits of tied arch bridges and trusses in a single system, thus it has a very good stiffness even in the case of extremely slender structures. In a Network Arch the hangers are inclined and some of them intersect each other at least twice. The core of a NAB is the hanger arrangement that minimizes the bending moment in the arch to very small values, leading thus to compression in the arch. This paper reviews the Network Arch idea devised by prof. Tveit and extended by researchers and engineers worldwide. A comprehensive review of the literature about the Network Arch is provided and the situation of NABs around the world from the standpoint of location, span, structural system used for the cross-section, bridge type (road, railway, combined or pedestrian) and opening year is discussed.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

Understanding the distribution of rock glaciers provides key information for investigating and recognizing the status and changes of the periglacial environment. Deep learning algorithms and red-green-blue (RGB) bands from high-resolution satellite images have been extensively employed to map rock glaciers. However, the near-infrared (NIR) band offers rich spectral information and sharp edge features that could significantly contribute to semantic segmentation tasks, but it is rarely utilized in constructing rock glacier identification models due to the limitation of three input bands for classical semantic segmentation networks, like DeeplabV3+. In this study, a dual-encoder DeeplabV3+ network (DEDNet) was designed to overcome the flaws of classical DeeplabV3+ network (CDNet) when identifying rock glaciers using multispectral remote sensing images by extracting spatial and spectral features from RGB and NIR bands, respectively. This network, trained with manually labeled rock glacier samples from QiLian Mountains, established a model with accuracy, precision, recall, specificity, and mIoU (Mean Intersection over Union) of 0.9131, 0.9130, 0.9270, 0.9195, and 0.8601, respectively. The well-trained model was applied to identify new rock glaciers in a test region, achieving a producer's accuracy of 93.68% and a user's accuracy of 94.18%. Furthermore, the model was employed to two study areas in northern Tien Shan (Kazakhstan) and Daxue Shan (Hengduan Shan, China) with high accuracy, which proved that the DEDNet offers an innovative solution to more accurately map rock glaciers on a larger scale due to its robustness across diverse geographic regions.

The objective of this study was to carry out the extraction and characterization of chitin and chitosan from the exoskeletons of the Farfantepenaeus californiensis species of shrimp, as well as its application in the formulation of polymeric films plasticized with glycerol used in the process of food packaging. The characterization of the extracted polymer was made by Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and physicochemical analysis of chitin and chitosan, resulting in a theoretical performance of 29.33% and 16.46%, respectively. In terms of quality, it was determined that the extracted chitosan had a molecular weight of 1.10 x105 g/mol and a deacetylation degree of 80.23%, which classifies it as a low-molecular weight chitosan, suitable for food packaging. It was shown that the extracted chitosan is fit for the production of the films by using the casting method, presenting a tension resistance of 1 MPa. The Antibacterial analysis was carried out using Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), bacterial models commonly found in food. The results showed an effective inhibition capability of the polymeric materials. Overall, the results for both chitosan and the films indicate a high potential for application in the food packaging sector.

Brain tumor being one of the major health hazards always needs a prompt diagnosis for the early treatment options to improve the chances of the survival of the patients. Traditional manual assessment of MRI (magnetic resonance imaging) to identify these conditions is a common practice. Hence, automation of the diagnosis practices can considerably improve the quality of the treatment procedures. In recent years almost every method for the automated diagnosis of brain tumor detection uses a deep learning technique. Despite decent works current techniques need a significant improvement to produce better results. Along with failure to produce decent results, the current deep learning models present very complex architectures which sometimes require huge computational resources. Therefore, in this paper we present a novel method that uses a lightweight dual-stream model with dual-input to detect brain tumors on MRI images. Both the inputs use different pre-processing mechanisms based on Contrast Limited Adaptive Histogram Equalization (CLAHE) and White Patch Retinex algorithm in order to enhance the feature learning capabilities of the proposed model. In addition, the proposed method uses a two-fold margin loss to boost training process for better feature learning. The proposed method produces state-of-the-art results for the detection of Glioma, Meningioma and Pituitary tumors. The model presents accuracy of 99%, 98% and 99% respectively for Glioma, Meningioma and Pituitary tumor detection.

Long-lasting insecticidal nets (LLINs) have been the main contributor to the reduction of malaria in the past two decades in sub-Saharan Africa. Development of pyrethroid insecticide resistance threatens the effectiveness of these LLINs, especially when nets become holed and the insecticide decays. Three classes of dual active ingredient (AI) LLINs, have been assessed for their physical durability as follows: 1) Royal Guard®, combining pyriproxyfen, which is known to disrupt female reproduction and fertility of eggs, and a pyrethroid alpha-cypermethrin; 2) Interceptor® G2, two adulticides with differing modes of action; chlorfenapyr and alpha-cypermethrin; 3) OlysetTM Plus incorporates permethrin (pyrethroid) and a synergist, piperonyl butoxide, to enhance the potency of pyrethroid insecticides; all nets were compared to standard pyrethroid only net (Interceptor®). About 40,000 nets of each type were distributed in February 2019 to different villages in Misungwi. A total of 3072 LLINs were followed at 6, 12, 24, 30 and 36 months to assess survivorship and fabric integrity in a community setting. The median functional survival were less than three years with Interceptor®, Interceptor® G2 and Royal Guard® having 1.9 year each and 0.9 years for OlysetTM Plus . After 36 months, 90% of OlysetTM Plus and Royal Guard® and 87% of Interceptor® G2 were no longer present (thrown away) in the households due to wear and tear, compared to 79% for standard Interceptor®. Short life spans of all assessed LLINs were driven by material of the net, rather than social economic status and housing material. All dual AI LLINs have a poor textile durability with OlysetTM Plus being the worst of the three.

In recent years, the prevalence of tobacco and electronic cigarette (e-cigarette) use among adolescents has raised significant public health concerns worldwide. This study aims to investigate respiratory symptoms among Polish adolescents. We conducted an online survey among Polish school students from all provinces, collecting data over two months in Spring 2021. Students voluntarily complete the anonymous survey, answering questions about respiratory symptoms, smoking habits (both traditional and electronic cigarettes), and demographic information. Analysis focused on four subgroups: non-tobacco users, traditional cigarette smokers, e-cigarette users, and dual users, totaling 10,388 pupils aged 12-18 years, predominantly attending secondary technical and comprehensive schools. A total of 10388 pupils participated in the study, 55.6 % (5778) of whom were girls and 44.4 % (4610) boys. Adolescents, who admitted using both e-cigarettes and traditional cigarettes experienced more frequent episodes of cough during the day (39.70%) and at night (18.40%) compared to their peers in other groups. Chest discomfort, including pain and pressure, was also reported more often by adolescents, who used e-cigarettes and traditional cigarettes concurrently (27.60%) compared to their peers in other groups. Chest pressure was experienced less commonly by non-smoking adolescents (14.40%) than by smokers (18.90%). Higher severity of cough during the day and at night was observed in the group of adolescents using traditional cigarettes and e-cigarettes concurrently compared to the other groups. The adolescents in the dual user group experienced more severe dyspnoea and wheezing compared to the other groups included in the comparison. The results of this study confirm the correlation between the occurrence of respiratory symptoms in adolescents who smoke cigarettes, use e-cigarettes and in dual users. The respiratory symptoms occur most frequently and are the most severe in the group of adolescents who use e-cigarettes and traditional cigarettes

Ocean wave energy is a significantly well-liked renewable energy source. The Internet of Things (IoT) offers a great opportunity for development of the ocean wave energy research. The IoT technology significantly enhanced the performance of the ocean wave energy converter (WEC). The data obtained from IoT devices reduce the risk of using WEC. However, Integrating IoT devices with the WEC is a daunting task because controlling the WEC needs real-time data. This paper investigated the performance of WEC and estimate the lifetime of the modules. IoT devices integrated with various sensors determine different parameters and conditions of the ocean. The IoT platform is used for wireless voltmeters, wireless AC current meters, wireless voltage detection, wireless resistance sensors, wireless temperature sensor, wireless accelerometer, wireless pressure meters, and wireless water level sensors to determine the real-time condition of the ocean wave. These devices are also proven to be reliable and accurate.

This research presents a maximum power point tracking of traditional single-ended primary converter (SEPIC) with the aid of fuzzy logic controller (FLC) for regulating the voltage and perturbation and observation(P&O) algorithms for regulating the reference voltage and reaching the maximum power point tracking. This is a promising technique for the conventional SEPIC converter to achieve maximum power point tracking with much less error. Moreover, the method is simple, reliable, and understandable for photovoltaic systems.

The matrix converter converts the input line voltage into a variable voltage with an unrestricted output frequency without using an intermediate circuit, dc link circuit. A pure sine in and pure sine out is the unique feature of the matrix converter. This research paper also analyzes the basic operating principle and the simulation modeling of the direct matrix converter, which is controlled by the Space Vector Pulse Width Modulation technique by using the software which is known as MATLAB/Simulink. The most desirable features in the power frequency changes can be fulfilled by using the matrix converters, and this is the reason for the tremendous interest in the topology. Since the power electronic circuits which is known as the motor drives are used to operate the AC motors at the frequencies other than that of the supply.

In this paper, a method of charging lead acid battery with solar power by flyback converter is proposed. The basic system consists of a buffer circuit, auxiliary power circuit, control circuit, voltage feedback circuit and current feedback circuit. The system is capable of monitoring battery voltage and the current, charging the coupling inductor and automatic control of output duty cycle, overcharging and over-discharging protection. The experiment proves that the charging efficiency is improved by about 83% at full load.

Запропонована методика спрямована на визначення та прогнозування технічного стану елементів мосту, що може слугувати прогресивним інженерним інструментом для оцінки надійності та довговічності. Розроблено на основі фундаментальних досліджень, які узагальнюють досвід вивчення фізико-механічних і фізико-хімічних властивостей матеріалів мостових конструкцій, що експлуатуються в реальних умовах. Теоретичною основою методики є модель надійності та прогнозування залишкового ресурсу елементів мосту на основі теорії Маркова. Розроблена методика призначена для оцінки технічного стану окремих елементів мосту з подальшою комплексною оцінкою всієї конструкції. За показник технічного стану прийнята надійність при експлуатації. Цей кількісний показник надійності в моделі є критерієм для: оцінки рівня безпеки елементів мосту; ранжування елементів мосту за необхідністю для конкретних видів ремонту, реконструкції або заміни; стратегічне планування витрат на ремонт або реконструкцію в умовах обмеженого фінансування; прогнозування залишкового ресурсу елементів. Для застосування розробленої методики запропоновано алгоритм оцінки та прогнозування технічного стану мостів. Було проведено математичний експеримент розробленої методики, який підтвердив адекватність висунутої гіпотези, тобто використання моделі надійності та прогнозування залишкового ресурсу елементів мосту. По-перше, запропоновано триступеневий механізм уточнення технічного стану мосту, суттєво підвищення точності розрахунків. Тому розроблена методика має практичне значення і може слугувати основою для інформаційно-аналітичних систем управління станом мостів.

The soil-structure interaction represents an important parameter when analyzing the dynamic behavior of bridges, taking into account the integration between soil, foundation, and structure to ensure an adequate structural representation. In this paper, a computational modeling strategy using soil-structure interaction (SSI) methodology was applied to represent the dynamic behavior of a pedestrian bridge (LOP). The computational models were validated using monitoring results from an extensive structural health monitoring campaign. The bridge monitoring program was characterized using embedded sensors and cutting-edge technology for remote monitoring: ground-based radar interferometry and video motion amplification. The instrumentation results were compared to establish the capabilities and advantages of this novel remote monitoring technique. The experimental results obtained from free and forced vibrations in the asset served as a basis for validating the developed computational model and allowed evaluating the asset be-havior in service for different loading conditions. This paper emphasizes the SSI approach to represent the pedestrian bridge dynamic behavior more accurately, allowing computational models to represent the LOP structural responses over the course of its life-cycle.

Dengue (DENV) and Zika (ZIKV) virus continue to pose significant challenges globally due to their widespread prevalence and severe health implications. Given the absence of effective vaccines and specific therapeutics, targeting of the highly conserved NS5 RNA-dependent RNA polymerase (RdRp) domain has emerged as a promising strategy. However, limited efforts have been made to develop inhibitors for this crucial target. In this study, we employed an integrated in silico approach utilizing combinatorial chemistry, docking, molecular dynamics simulations, MM/GBSA, and ADMET studies to target the allosteric N-pocket of DENV3-RdRp and ZIKV-RdRp. Using this methodology, we designed lycorine analogs with natural S-enantiomers (LYCS) and R-enantiomers (LYCR) as potential inhibitors of non-structural protein 5 (NS5) in DENV3 and ZIKV. Notably, 12 lycorine analogs displayed a robust binding free energy (&lt;-9.00 kcal/mol), surpassing that of RdRp-Ribavirin (&lt;-7.00 kcal/mol) along with promising ADMET score predictions (&lt;4.00), of which (LYCR728-210, LYCS728-210, LYCR728-212, LYCS505-214) displayed binding properties to both DENV3 and ZIKV targets. This study highlights the potential of non-nucleoside lycorine-based analogs with different enantiomers that may present different or even completely opposite metabolic, toxicological, and pharmacological profiles as promising candidates for inhibiting NS5-RdRp in ZIKV and DENV3, paving the way for further exploration for the development of effective antiviral agents.

Climate change, increasing global food needs, and decreasing global resources brought a new era to human every-day live with a strong turn to circular economy and sustainability. Food packaging and preservation is an important global sector where enchanced research is carried out. New methods such as active packaging and chemical preservatives replacement are of major interest. Many researchers were published studies about active packaging films, replacement of chemical preservatives with natural originated extracts, and novel incorporation procedures. Sequentially to our and other scientists’ previous work, in this paper we present the results of the improvement which was achieved by incorporating the developed nanohybrid of natural-halloysite/carvacrol-extract, the pure natural carvacrol extract and the commonly used low-density-polyethylene. The well known corona-treatment procedure was employed to produced the optimum final film and the results shown that the low-density-polyethylene incorporated with natural-halloysite/carvacrol-extract nanohybrid and coated external with extra carvacrol extract exhibited aproximatelly 100% higher Young-Modulus values, slightly decreased ultimate strength by 20%, and almost stable elonation at break properties. The water-vapor and oxygen barrier increased by 40%. Finally, the antioxidant activity of the corrona-treated film increased by 28% compared to the similar but untreated product because of the lower release rate of the carvacrol.

It is challenging to apply heat flow through a thermal bridge, which requires the analysis of 2D or 3D heat transfer to building energy simulation(BES). Research on the dynamic analysis of thermal bridges has been underway for many years, but their utilization remains low in BESs. This paper proposes a thermal bridge modeling and a dynamic analysis method that can be easily applied to BESs. The main idea begins with an analogy of the steady-state analysis of thermal bridges. As with steady-state analysis, the proposed method first divides the thermal bridge into a clear wall, where the heat flow is uniform, and the sections that are not the clear wall (the thermal bridge part). For the clear wall part, the method used in existing BESs is applied and analyzed. The thermal bridge part (TB part) is modeled with the linear time-invariant system (LTI system) and the system identification process is performed to find the transfer function. Then, the heat flow is obtained via a linear combination of the two parts. This method is validated by comparing the step, sinusoidal and annual outdoor temperature response of the finite differential method(FDM) simulation. When the thermal bridge was modeled as a third-order model, the root mean square error(RMSE) of annual heat flow with the FDM solution of heat flow through the entire wall was about 0.1W.

A two-year experiment was conducted with a local maize hybrid under full irrigation (F), deficit irrigation (D) and rainfed conditions (R) to estimate maize evapotranspiration in Bosnia and Herzegovina. Three approaches (Allen & Pereira (A&P), SIMDualKc (SD), and Vegetation Index (VI)) were used to estimate the actual crop coefficient (Kc act), actual basal crop coefficient (Kcb act), and actual crop evapotranspiration (ETc act) were applied with the dual crop coefficient method and remote sensing (RS) data. While Kcb act from all approaches matched FAO56 tabulated values, SD showed differences, in comparison to A&P, of up to 0.24 in D and R conditions, especially in initial and mid-season stages. VI demonstrated very good performance in all treatments. In F, the obtained Kc act for all approaches during the initial and end stages were higher than the tabulated values, ranging from 0.71-0.87 for Kc ini act and from 0.80-1.06 for Kc end act, while the mid-season period showed very good agreement with the literature. Maize crop evapotranspiration range is 769-813 mm, 480-752 mm, and 332-618 mm for F, D and R, respectively. The results confirmed the suitability of both approaches (SD and VI) to estimate maize crop evapotranspiration under F, with the VI approach demonstrating an advantage in calculating Kcb act, Kc act, and ETc act values under water stress conditions. The 67.6% increase in grain yields with irrigation emphasizes the need to transition from rainfed to irrigation-dependent agriculture, even for drought-resistant crops like maize.

Cholangiocellular carcinoma (CCA) is the second most common primary liver cancer, with increasing incidence worldwide and inadequate therapeutic options. Intra- and extrahepatic bile ducts have distinctly different embryonic origins and developmental behavior, and accordingly intra- and extrahepatic CCAs (ICC vs. ECC) are molecularly different. A promising strategy in oncotherapy is targeted therapy, targeting proteins that regulate cell survival and proliferation; such as the MAPK/ERK and PI3K/AKT/mTOR signaling pathways. Inhibitors of these pathways have been tested previously in CCA cell lines. However, these cell lines could not be clearly assigned to ICC or ECC, and results indicated apoptosis induction by targeted therapeutics. We tested targeted therapeutics (selumetinib, MK2206) in three defined ICC cell lines (HuH28, RBE, SSP25). We observed cooperative effects of dual inhibition of the two pathways, in accordance with inhibition of phospho-AKT and phospho-ERK1/2 expression. Proliferation was blocked more effectively with dual inhibition than with each single inhibition, but cell numbers did not drop below baseline. Accordingly, we observed G1-phase arrest, but not apoptosis (cleaved caspase-3, AIFM1 regulation, subG1-phase) or necroptosis (phospho-MLKL). We conclude that dual inhibition of MAPK/ERK and PI3K/AKT/mTOR pathways is highly effective to block proliferation of ICC cell lines, but therapy must certainly be supplemented with standard therapies.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Rhodiola rosea, a perennial herb from the Crassulaceae family, contains the bioactive compound salidroside, recognized as an adaptogen with significant therapeutic potential for bone metabolism. Salidroside promotes osteoblast proliferation and differentiation by activating critical signaling pathways, including bone morphogenetic protein-2 and adenosine monophosphate-activated protein kinase, essential for bone formation and growth. It enhances osteogenic activity by increasing alkaline phosphatase activity and mineralization markers, while upregulating key transcription factors such as runt-related transcription factor 2 and osterix. Additionally, salidroside facilitates angiogenesis via the hypoxia-inducible factor 1-alpha and vascular endothelial growth factor pathway, crucial for coupling bone formation with vascular support. Its antioxidant properties offer protection against bone loss by reducing oxidative stress and promoting osteogenic differentiation through the nuclear factor erythroid 2–related factor 2 pathway. Salidroside's ability to counteract the negative effects of glucocorticoids on bone cells and prevent steroid-induced osteonecrosis, along with its anti-inflammatory properties, enhances its potential in treating conditions like osteoarthritis. These attributes underscore its multifaceted role in bone metabolism. This article reviews the literature, including in vitro and in vivo studies primarily on rodent models, demonstrating salidroside's efficacy in mitigating bone loss, preserving bone microarchitecture, and accelerating fracture healing. Future research directions to explore salidroside’s applications in bone-related diseases are also highlighted.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

In this research paper, a high gain transformer less inverter modeling which is used for the smart grid technology or as the stand alone for home appliances is proposed. The proposed transformer less topology provides a higher voltage gain, low cost, small size and simple control stand alone transformer less inverter for home appliances. The above inverter is modeled by using software which is known as MATLAB/ Simulimk.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

We elucidate the versatility of intriguing symmetry and asymmetry phenomena outside and inside black holes. For description of the test particle (planet and photon) motion it is used the Kerr-Newman metric of the rotating and electrically charged black hole. In particular, it is demonstrated the symmetry and asymmetry of the one-way Einstein-Rosen bridge inside black hole toward and through the plethora of endless and infinite universes.

It is standard for blockchain platforms to issue native tokens, currencies, that users must own to operate within the platform. Some blockchains however decided to issue two tokens, a dual system, one typically for governance and the other for implementing functions on the blockchain, such as executing transactions or smart contracts. Therefore, the two tokens are used for different activities. Typically, owning the governance tokens gives right to receive the other token for free, as a reward for participating to the blockchain decision-making process. However, both tokens can also be traded on some exchange nodes, which means that platform functions could be implemented even without owning governance tokens. In the paper we discuss some economic fundamentals of dual-token blockchain platforms. In particular, we investigate the market relative attractiveness of the two tokens by introducing some simple numerical indicators, based on prices, traded and circulating monetary quantities. Such indicators, which are meant to reflect the platform view on the tokens’ market desirability, could be computed in real time and used to support the platform’s policy making.

The recent Planck Legacy release confirmed the existence of an enhanced lensing amplitude in the cosmic microwave background (CMB) power spectra, which endorses the positive curvature of the early Universe with a confidence level exceeding 99%. In this study, the pre-existing curvature is incorporated to extend the field equations where the derived wave function of the Universe is utilized to model Universe evolution with reference to the scale factor of the early Universe and its radius of curvature upon the emission of the CMB. The wave function reveals both positive and negative solutions, implying that matter and antimatter of early Universe plasma evolve in opposite directions as distinct Universe sides. The wave function indicates that a nascent hyperbolic expansion is followed by a first phase of decelerating expansion away from early plasma during the first 10 Gyr, and then, a second phase of accelerating expansion in reverse directions, whereby both Universe sides free-fall towards each other under gravitational acceleration. Simulations of the predicted conformal curvature evolution demonstrate the fast orbital speed of outer stars owing to the external fields exerted on galaxies as they travel through conformally curved space-time. Finally, the wave function predicts an eventual time-reversal phase comprising rapid spatial contraction that culminates in a Big Crunch, signalling a cyclic Universe. These findings reveal that early plasma could have separated and evolved into distinct sides that collectively and geometrically influencing the Universe evolution, physically explanting the effects attributed to dark matter and energy.

Although mammography has been the gold standard for early detection of breast cancer, if a woman has dense breast tissue, a false negative diagnosis may occur. Breast ultrasound, whether hand-held or automated, is a useful adjunct to mammography but adds extra time and cost. The primary aim was to demonstrate that our second-generation Aceso system, which combines full-field digital mammography (FFDM) and automated breast ultrasound (ABUS) in a single platform, is able to produce improved quality images that provide clinically meaningful results. Aceso was first tested using two industry standards: a CDMAM phantom to assess the FFDM images; and the CIRS 054GS phantom to evaluate the ABUS images. In addition, 25 women participated in a clinical trial: 14 were healthy volunteers while 11 were patients referred by the breast clinic at Groote Schuur Hospital. The CDMAM phantom results showed the FFDM results were better than EUREF’s standard of “acceptable” and were approaching “achievable”. The ABUS results showed lateral and axial spatial resolution of 0.5 mm and adequate depth penetration of 80 mm. Our second-generation Aceso system, with its improved quality of clinical FFDM and ABUS images, has demonstrated its potential for early detection of breast cancer in a busy clinic.

Current trends in systemic risk literature provide new insights into multi-hazard risks that interact and compound with built environments, creating more significant impacts on socio-economic and human systems. Recurrent natural hazards and extreme weather events are more likely to compound and cascade into more impactful events, especially in vulnerable societies. In small-island communities (SICS), including large archipelagos and Small Island Developing States (SIDS), the long-term impact of multi-, compounding-, and cascading-hazards (MCC hazards) can result in persistent vulnerability and residual risks. This is due to delayed responses, limited resources, poverty, fewer evacuation options, and inadequate markets and infrastructure. Using Ternate, a densely populated small volcanic island in North Maluku, Indonesia, as a case study, this paper assesses the impacts of seven types of natural hazards: flash floods, landslides, extreme weather, extreme waves and abrasion, earthquakes, tsunamis, and volcanic eruptions. The research focuses on the multi-hazard impact on population, land use, and infrastructure exposures in 60 villages in Ternate. The findings highlight population density, land use, and infrastructure exposure to multi-hazard risks, providing valuable information on potential losses in future hazard events.

The need for effective bridge asset management in Indonesia has become crucial. Currently, the number of bridge assets in Indonesia is continuously increasing, parallel to the rising budget allocations for infrastructure development in the road and bridge sectors to enhance regional connectivity more efficiently. This situation places demands on asset managers to work harder and possess expertise in bridge asset management. However, the reality reveals persistent issues related to the incapacity of bridge asset managers in various regions to manage their assets effectively. This raises the question of whether asset managers have the intention to implement asset management or what factors might drive their appeal to have an intention towards effective asset management. To address these questions, a survey was conducted involving asset managers and experts to evaluate the current state of bridge asset management in Indonesia. The research findings provide insights into the relationships among factors such as budget, data, policy, resources, and system that associated with bridge asset management and the intention of an asset manager. The model's solutions show that data and system are anticipated to achieve effective and efficient implementation of bridge asset management. It is hoped that this research will assist asset managers in Indonesia in enhancing their intention towards better bridge asset management.

A temporary monitoring system was installed on the 175-years-old historical Széchenyi chain bridge under its reconstruction process. The bridge is in the downtown area of the capital city of Hungary and plays a significant role in city life of Budapest. Six-month-long measurements were conducted during the reconstruction process of the bridge, yielding crucial insights into the structural behaviour of the historical structure. Measurement results were evaluated; the findings encompass the rotation capacity of pins between chain elements, and structural response to temperature changes. This information helped the decision-making of designers and construction company during the reconstruction made between 2021 and 2023. For instance, daily temperature fluctuations result in increased bending moments in the chain elements, rising up to 158% compared to the values observed during a proof load test in 2018. Furthermore, the measurements reveal an approximate 42% increase in normal forces compared to the proof load test, which highlights the high sensitivity of chain bridges to temperature fluctuations, where geometric stiffness plays a crucial role. Reconstruction, reducing self-weight, notably intensifies the impact on normal forces and bending moments. These outcomes strongly emphasize the dominance of dead load and self-weight in the case of chain bridges.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

Originally developed to image the shadow region of the central black hole in Sagittarius A* and in the nearby galaxy M87, the Event Horizon Telescope (EHT) provides deep, very high angular resolution data on other AGN sources too. The challenges of working with EHT data have spurred the development of new image reconstruction algorithms. This work briefly reviews the status of the EHT and its utility for observing AGN sources, with emphasis on novel imaging techniques that offer the promise of better reconstructions at 1.3 mm and other wavelengths.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

This article presents a decentralized phase-shedding technique for multiphase converters. The usual central digital controller is replaced by identical local controllers forming a daisy-chain structure. Phase-shedding decisions are taken locally based on a local inductor current monitoring and threshold crossing management. This control strategy allows to implement as many phases as desired in a modular manner. In order to handle specific events such as load current inrush or a start-up sequence and to guarantee optimal transient responses, additional functions are included into each local controllers. The inter-cell communication protocol is described, along with necessary design considerations of threshold and timing values. Finally, functional simulations are carried out on a 5-leg 12V/1.2V 60W multiphase converter, which validate the proposed decentralized phase-shedding strategy for a microcontroller power supply implementation.

Offshore wind farms are increasingly built in the North Sea and the number of HVDC systems transmitting the wind power to shore increases as well. To connect offshore wind farms to adjacent AC transmission systems, onshore and offshore modular multilevel converters transform the transmitted power from AC to DC and vice versa. Besides, modern wind farms mainly use wind turbines connected to the offshore point of common coupling via voltage source converters. However, converters and their control systems can cause unwanted interactions, referred to as converter-driven stability problems. The resulting instabilities can be predicted by applying an impedance-based analysis in the frequency domain. Considering that the converter models and system data are often confidential and cannot be exchanged in real systems, this paper proposes an enhanced impedance measurement method suitable for black-box applications to investigate the interactions. The proposed method is applied to assess an offshore HVDC system’s converter-driven stability, using impedance measurements of laboratory converters and a wind turbine converter controller replica. The results show that the onshore modular multilevel converter’s interactions with AC grids of moderate short-circuit ratios can lead to instabilities. The offshore system analysis reveals that considering the offshore grid topology is crucial for assessing interactions between the wind turbine controllers and the offshore modular multilevel converter. It is shown that different stability margins result from varying offshore grid layouts.

Reliable and robust control of power converters is a key issue in the performance of numerous technological devices. In this paper we show a design technique for the control of a DC-DC buck converter with a switching technique that guarantees not only good performance but also global stability. We show that making use of the contraction theorem in the Jordan canonical form of the buck converter, it is possible to find a switching surface that guarantees stability but it is incapable of rejecting load perturbations. To overcome this, we expand the system to include the dynamics of the voltage error and we demonstrate that the same design procedure is not only able to stabilize the system to the desired operation point but also to reject load, input voltage and reference voltage perturbations.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

The Sei Dareh Bridge is a cable-stayed bridge located in West Sumatra Province, Indonesia. The bridge, which crosses the Batanghari River, has a main span of 123 meters long and 9 meters wide. Traffic load is transmitted through 24 prestressed cables to a 42.4-meter-high pylon made of concrete. The bridge deck and traffic loads are directly supported by steel box girders as main beams that are reinforced laterally with cross beams IWF 800.300.16.24 and stringers IWF 350.350.12.19. This paper discusses static and dynamic testing on the bridge which aims to assess its feasibility before it is opened to the public. Based on the test, it was concluded that a static load of 73% could not be achieved because the deflection that occurred was beyond the allowable deflection. This is exacerbated by a loud clanging sound on the ST2-X1 prestressed cable when loading to 240 tons or 58% of the targeted load. In addition, this bridge is included in the "lazy bridge" category because it takes 24 hours to return to an undeformed condition after loading. As a recommendation for this bridge, it is necessary to carry out a structural health monitoring system (SHMS) regularly on bridge slabs and cables.

The bridge crane is often used in a complex environment, often subject to interference of all loads. Some uncertainties factors often have an inevitable impact on its swing. So the force situation of the bridge crane during a working cycle is analyzed, and a three-dimensional dynamic mathematical model of the bridge crane is built. Through the simulation analysis of the model under the action of driving force and wind load, the change law of the swing angle of the bridge crane is studied. Then, the fuzzy control theory is used to determine the control parameter in the anti sway control process. The position, swing angle deviation and deviation rate of the bridge crane are taken as the input, and the parameter correction is obtained after the fuzzification by using the center of gravity method, the anti sway fuzzy control system of the bridge crane is designed and simulated. The research results show that the fuzzy PID anti sway controller can not only improve the adaptability of the control system, but also overcome the large overshoot, quickly restrain the swing, and effectively realize the anti sway function of the bridge crane.

Research for a theory of quantum gravity has recently led to the use of presheaf topos. Quantum uncertainty is linked to the truth values of intuitionistic logic. This paper proposes transposing this model into a classic probability context, that of conditional mathematical expectations. A simulation of Brownian motion is offered for illustrative purposes.