Experimental quantification of retention factors related to post-fire strength as well as post-fire ductility of intentionally selected stainless steel grades applied in construction is the objective of research presented here. These steel grades are characterized by a two-phase austenitic-ferritic microstructure of the duplex type. In this context two mutually corresponding chromium-nickel-molybdenum steel grades have been subjected to analysis, namely X2CrNiMoN22-5-3 steel belonging to the standard duplex group (DSS 22% Cr) and X2CrMnNiN21-5-1 steel belonging to the lean duplex group (LDSS). The similarities and differences in the mechanical properties exhibited by these steel grades after effective cooling, following more or less prolonged simulated fire action conforming to several development scenarios, have been identified and indicated. The resistance of given steel grade to permanent structural changes induced by the heating program proved to be the critical factor determining these properties and resulting in many cases in increased susceptibility to brittle fracture.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

This research investigates the intricate dynamics between intellectual Capital (VAIC) and the stability of banks in the evolving context of Saudi Arabia's banking sector. Against the backdrop of rapid economic reforms under Vision 2030 and the challenges imposed by the COVID-19 pan-demic, the research provides a nuanced analysis of how intellectual capital and intellectual capital's components—Human Capital Efficiency (HCE), Structural Capital Efficiency (SCE), and Capital Employed Efficiency (CEE)—affect the financial stability of Saudi banks. The research analyses a decade-long panel dataset from 2012 to 2022, utilizing both fixed effects and cross-section random effects models to discern the impact of intellectual capital on bank stability. The findings reveal a positive overall influence of intellectual capital on bank stability; however, individual compo-nents present a complex relationship, with CEE showing a positive association and HCE and SCE demonstrating unexpected negative correlations with bank stability. The research identifies lev-erage (LEV) as a significant factor negatively impacting stability. Operational efficiency (OPEF) and size (SIZE) also negatively affect stability. Surprisingly, macroeconomic indicators and bank size exhibit non-significant effects on bank stability. Similarly, the direct impact of the COVID-19 pandemic was found to be non-significant, suggesting a resilient banking environment or the presence of effective mitigating strategies. As Saudi Arabia continues its ambitious economic transformation, this research underscores the critical role of effectively managed intellectual capital in ensuring the banking sector's stability. It provides a foundation for ongoing research in this vital area.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

Relationship between the results of penile duplex doppler ultrasound (PDDU) and response to vardenafil was investigated in patients diagnosed with erectile dysfunction (ED). Data of 148 patients with ED were analysed retrospectively. Patients who did not respond to therapy were classified as Group I (n = 32), those responded partially were classified as Group II (n = 40) and complete responders were classified as Group III (n = 76). Age, comorbid diseases, vascular and penile pathology were compared among the three groups. While diabetes mellitus (DM) and dyslipedimia positivity adversely affect the response to treatment, the presence of hypertension (HT), peyronie's disease and priapism increase the therapeutic response to the treatment (p < 0.05). Arterial insufficiency was present in 20(30.3%), 25(37,9%) and 21(31.8%) of the patients in Group I, Group II and Group III, respectively (p = 0.001). Venous insufficiency was observed in 3(14.3%) patients in Group I and in 8(85.7%) patients in Group III (p = 0.001). Arterial/venous insufficiency was seen in 9(30%), 14(46.7%) and 7(23.3%) of the patients in Group I, Group II and Group III, respectively (p = 0.001). Response rate to treatment was highest in normal patients according to PDDU, followed by patients with venous insuffiency. Besides, it was found that DM decreased the response to treatment, whereas response was increased in cases with HT, priapism and Peyronie’s disease.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

Duplex and Super Duplex Stainless Steels are very prone to secondary phases formation related to ferrite decomposition at high temperatures. In the present paper the results on secondary phase precipitation in a 2510 Duplex Stainless Steel, heat treated in the temperature range 850-1050 °C for 3-30 minutes are presented. The precipitation starts at grain boundaries with a consistent ferrite transformation for very short times. The noses of the TTP curves are at 1000 °C for σ-phase and at 900 °C for χ-phase, respectively. The precipitation sequence involves a partial transformation of χ into σ, as previously evidenced in 2205 and 2507 grades. Furthermore, the experimental data were compared to the results of Thermo-Calc calculations.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p&lt;0.05; p&lt;0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p&lt;0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

The skyrocketing growth in the number of Internet of Things (IoT) devices will certainly pose a huge traffic demand for fifth-generation (5G) wireless networks and beyond. In-band full-duplex (IBFD), which is theoretically expected to double the spectral efficiency of a half-duplex (HD) wireless channel and to connect more devices, has been considered as a promising technology to accelerate the development of IoT. To exploit the full potential of IBFD, the key challenge is how to handle network interference (including self-interference, co-channel interference and multiuser interference) more effectively. In this paper, we propose a simple yet efficient user grouping method, where a base station (BS) serves strong downlink users and weak uplink users and vice versa in different frequency bands, mitigating severe network interference. We aim to maximize a minimum rate among all users subject to bandwidth and power constraints, which is formulated as a highly nonconvex optimization problem. By leveraging inner approximation framework, we develop a very efficient iterative algorithm to solve this problem, which guarantees at least a local optimal solution. Numerical results are provided to show not only the benefit of using full-duplex raido at BS, but also the advantage of the proposed user grouping method.

Cooperative Non-Orthogonal Multiple Access (NOMA) with Simultaneous Wireless Information and Power Transfer (SWIPT) communication can effectively improve the spectrum efficiency and energy efficiency of the wireless networks with extend coverage. An important design issue is to incentivize a relaying center user to participate in the cooperative process and achieve a win-win situation to both the BS and the center user. Some private information of the center users are hidden from the BS in the networks. We apply a contract theory-based incentive mechanism under such asymmetric information scenario to incentives center user to join the cooperative communication to maximize the BS profit utility and to guarantee the center user’s expect payoff. A match theory-based Gale-Shapley algorithm is proposed to obtain the optimal strategy with low computation complexity. Simulation results indicated the network performance of our proposed cooperative transmission is much better than the conventional NOMA transmission and the benefit utility of the BS with the stable match strategy is nearly close to the complete channel state information multi-users scenario while the center users get the satisfied expect payoffs.

: Early and accurate detection of infectious diseases is a key step for surveillance, epidemiology, and control, notably timely disease diagnosis, patient management and follow-up. In this study, we aimed to develop hand-held ultra-fast duplex PCR assays coupled to amplicon detection by lateral flow (LF) immunoassay to deliver a rapid, and simple molecular diagnostic test for con-comitant detection and identification of the main Leishmania parasites encountered in Tunisia and the Old World. We selected two DNA targets to amplify L. major/L. tropica and L. infantum/L. tropica group of species DNAs, respectively. We optimized the experimental conditions of a du-plex ultra-fast PCR. The amplification is performed by a portable Palm convection PCR machine within 18 min and the products are detected by a LF cassette within 10 minutes. The test allows the identification of the infecting species according to the position and number of test lines re-vealed. Tested on a selection of DNAs of representative Leishmania strains of the three studied species (N=37), the ultra-fast duplex PCR-LF showed consistent, stable, and reproducible results. The analytical limit of detection of the test was 0.4pg for L. major, 4pg for L. infantum and 40pg for L. tropica.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

The present work reports an experimental thermodynamic study of two nitrogen heterocyclic organic compounds, fenclorim and clopyralid, that have been used as herbicides. The sublimation vapor pressures of fenclorim (4,6-dichloro-2-phenylpyrimidine) and of clopyralid (3,6-dichloro-2-pyridinecarboxylic acid) were measured, at different temperatures, using a Knudsen mass-loss effusion technique. The vapor pressures of both crystalline and liquid (including supercooled liquid) phases of fenclorim were also determined using a static method based on capacitance diaphragm manometers. The experimental results enabled accurate determination of the standard molar enthalpies, entropies and Gibbs energies of sublimation for both compounds and of vaporization for fenclorim, allowing a phase diagram representation of the (p,T) results, in the neighborhood of the triple point of this compound. The temperatures and molar enthalpies of fusion of the two compounds studied were determined using differential scanning calorimetry. The standard isobaric molar heat capacities of the two crystalline compounds were determined at 298.15 K, using drop calorimetry. The gas phase thermodynamic properties of the two compounds were estimated through ab initio calculations, at the G3(MP2)//B3LYP level, and their thermodynamic stability was evaluated in the gaseous and crystalline phases, considering the calculated values of the standard Gibbs energies of formation, at 298.15 K.

The possibility of increasing wear resistance of the CP-Ti surface using a duplex surface treat-ment combining plasma electrolytic nitrocarburizing in a solution of ammonia, acetone and ammonium chloride and subsequent plasma electrolytic polishing is shown. Morphology and surface roughness, structure and microhardness of the modified layer were studied. The correla-tion of weight wear with hardness of diffusion layer at a low processing temperature and thick-ness of oxide layer is established – the largest decrease in weight wear occurs after nitrocarbu-rizing at 750 °C for 5 min (by 4.3 times). The possibility of an additional increase in wear re-sistance by subsequent polishing of the nitrocarburized CP-Ti surface at a voltage of 275–300 V for 3–5 min in chloride and fluoride electrolytes and 5–10 min in a sulfate electrolyte was re-vealed. Under these conditions, the hardened layer is preserved when the porous outer oxide layer is removed. According to the microtopology of the friction tracks, the wear mechanism is estimated as fatigue in dry friction and plastic contact.

The precipitate phases often play an important influence on the corrosion resistance of 2205 Duplex stainless steel (DSS). In the presented paper, the microstructure and corrosion resistance in the hot-rolled and cold-rolled 2205 DSS aging for different time at 850 °C was investigated by XRD, SEM and potentiodynamic polarization. It has been found that the Chi(χ) phase and Sigm(σ) phase were precipitated in turn after aging treatment of hot-rolled and cold-rolled materials, but the precipitate amount in cold-rolled material is much more than that of hot-rolled samples. The corrosion resistance of the solution-annealed cold-rolled material is similar to the hot-rolled material, but the corrosion resistance of cold-rolled material with precipitate is weaker than that of hot-rolled material after aging treatment. Pitting initiates preferentially in the Cr-depleted region from σ phase in aged hot-rolled 2205, and severe selective corrosion occurs on sigma/ferrite interfaces aged for a long aged lime. However, the initiation of pitting corrosion may take place at the phase boundary, defect and martensite in the aged cold-rolled 2205. The σ phase is further selectively dissolved by electrochemical method to investigate the difference of microstructure and corrosion behavior in hot-rolled and cold-rolled 2205 duplex stainless steel.

It was recently studied how to achieve the optimal degrees of freedom (DoF) in a multi-antenna full-duplex system with partial channel state information (CSI). In this paper, we revisit the DoF of a multiple-antenna full-duplex system using opportunistic transmission under the partial CSI, in which a full-duplex base station having M transmit antennas and M receive antennas supports a set of half-duplex mobile stations (MSs) having a single antenna each. Assuming no self-interference, we present a new hybrid opportunistic scheduling method that achieves the optimal sum DoF under an improved user scaling law. It is shown that the optimal sum DoF of 2M is asymptotically achievable provided that the number of MSs scales faster than SNR^M, where SNR denotes the signal-to-noise ratio. This result reveals that in our full-duplex system, better performance on the user scaling law can be obtained without extra CSI, compared to the prior work that showed the required user scaling condition (i.e., the minimum number of MSs for guaranteeing the optimal DoF) of SNR^2M−1.

The present paper describes a study case of the failure investigation of Duplex stainless steel (UNS S31803) on the tube and tube sheet section of a shell and tube heat exchanger BEM TEMA type with seawater as the cooling medium. Although UNS S31803 offers high strength, high resistance to chloride-induced SCC, and high resistance to pitting attack in chloride environments, in this study case, the heat exchanger experienced some material degradation; 26 tubes were leaked and plugged on both sides, and scales plugged 76 tubes. The examination in this study case revealed the formation of biofilm inside the tubes, XRD examination revealed that the film contained aragonite (CaCO3), and by using microstructural examination on the inner surface of the tube, the austenite grains were preferentially attacked by crevice corrosion. In this case, the failure was caused by crevice corrosion, and crevice corrosion was enhanced by microbiological-induced corrosion (MIC). Recommendations to avoid similar failures are also suggested in this paper.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

A fundamental tool in mathematical physics is the logarithmic Sobolev inequality. A quantitative version proven by Carlen with a remainder involving the Fourier-Wiener transform is equivalent to an entropic uncertainty principle more general than the Heisenberg uncertainty principle. In the stability, the remainder is in terms of an entropy, not a metric. Recently, a stability result for H¹ was obtained by Dolbeault, Esteban, Figalli, Frank, and Loss in terms of an L^p norm. Afterwards, Brigati, Dolbeault, and Simonov discussed the stability problem involving a stronger norm. A full characterization with a necessary and sufficient condition to have H¹ convergence is identified in this paper. Moreover, an explicit H¹ bound via a moment assumption is shown. Also, the L^p stability of Dolbeault, Esteban, Figalli, Frank, and Loss is proven to be sharp.

A study on flywheel geometries is presented here with the use of finite element modelling (FEM) simulations. The study analyses the stress behaviour of flywheel rotors subject to the rotational speed that creates the maximum stress that the flywheel can support, and then calculates the rotational energy mass ratio (energy density) for each geometry. The obtained geometry was Gaussian section for the Flywheel rotor. The used material for the simulations is carbon fibre Hexcel UHM 12000. The best results were a rotational speed of ≈279.000 rpm and rotational energy density of ≈ 440 Wh/kg for a single disk, but this keeps the total energy low. To increase the total energy, Flywheels with 2 and 3 rotors were analysed. Then the stability under rotation of these Flywheels were analysed, some instability was found and a solution was presented.

In this paper, we introduce a way of representing a given mapping as the sum of odd and even mappings. Then, by using this representation, we investigate the stability of various forms for the general nonic functional equation.

This review describes major advances in the use of functionalized molecular metal oxides (polyoxometalates, POMs) as water oxidation catalysts under electrochemical conditions. The fundamentals of POM-based water oxidation are described together with a brief overview of general approaches to designing POM water oxidation catalysts. Next, the use of POMs for homogeneous, solution-phase water oxidation is described together with a summary of theoretical studies shedding light on the POM-WOC mechanism. This is followed by a discussion of heterogenization of POMs on electrically conductive substrates for technologically more relevant application studies. Stability of POM water oxidation catalysts are discussed on selected examples where detailed data is already available. The review finishes with an outlook on future perspective and emerging themes in electrocatalytic polyoxometalate-based water oxidation research.

Modern portfolio theory claims that diversification into non-correlated or negatively correlated activities reduces the overall risk of a portfolio. Considering the total income of a bank as a portfolio of interest income and non-interest income, this paper investigates how the variability of interest income and non- interest income, and covariance between interest income and non-interest income influence the various risk factors of banks. We set out a study in the Indian context. We have extracted data for the period 2005-2017 and employed an extended version of Ridge, Lasso and Elastics Net regression to take care of multi-collinearly in our data. We have considered 10-fold cross-validation techniques to get optimal values of tuning parameters for Ridge, Lasso, and Elastics Net regression (which is a convex combination of ridge and the LASSO). We have compared different regression techniques by comparing RMSE and R2. We observe that non-interest income is positively correlated with interest income in the Indian context, but it does stabilize variance, idiosyncratic risk & market risk (Beta) of Indian Banks.

The synchronization of complex networks is believed to be closely related to network topology. How to study synchronization of real network without clear topology and parameters? In this Letter, a synchronized stability boundary equation is derived that is system- and disturbance-independent and applicable to arbitrarily coupled grids. The results imply that spontaneous synchronization in a network may be network independent. These conclusions provide new research paths for network synchronization and analyze the synchronization stability of grids in a unified way.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

An especially important species in southern Brazil, yerba mate (Ilex paraguariensis) is traditionally consumed as tea, chimarrão and tererê. Yerba mate consumption has been stimulated by scientific discoveries that have identified high concentrations of bioactive compounds and their health benefits. There are no studies or scientific evidence to certify or guarantee stability of these compounds’ concentrations during different years in the same plants. We were interested in quantifying caffeine, theobromine, total phenolic compounds and proteins concentrations in leaves of yerba mate genotypes and their stability in the same plants over four consecutive years. Mature leaves from yerba mate genotypes selected on a provenance and progenies trial were collected in August of 2015, 2016, 2017 and 2018. Methylxanthines (caffeine and theobromine), total phenolic compounds and total protein contents were quantified. Our results indicate large variations between genotypes regarding caffeine (0.035 to 2.385 g 100 g^-1), theobromine (0.0004 to 1.772 g 100 g^-1), total phenolic compounds (7.028 to 9.424 g 100 g^-1) and proteins (10.39 to 16.58 g 100 g^-1) contents, and also high stability of those compounds over the four evaluated years. A great variation of the studied bioactive compounds in different Ilex paraguariensis genotypes was found and its stability over four consecutive years was showed.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

Additive manufacturing (AM) or 3D printing of metals is gaining popularity due to its flexibility in fabricating parts with highly complex designs, as well as simplifying manufacturing steps and optimizing process times. In this investigation, 17-4 PH stainless steel was additively manufactured using Laser-Powder Bed Fusion (L-PBF), followed by functionalization through a DUPLEX treatment. This treatment involved a plasma-assisted nitriding process, followed by deposition of an arc-PVD c-Al0.7Cr0.3N hard coating. The microstructural modifications resulting from plasma nitriding (such as the formation of Fe2,3N and Fe4N, and the αN or expanded martensite phases), and the surface improvements with the c-Al0.7Cr0.3N coating on the 3D-printed 17-4 PH steel, are evaluated in comparison to conventionally manufactured 17-4 PH steel. These microstructural characteristics are correlated with the mechanical response of the treated surfaces. As a result of the plasma nitriding process, the hardness of the 3D-printed 17-4 PH SS increased by approximately 260%. The wear, measured through dynamic and static scratch-testing, was reduced by approximately 31%. This improvement was attributed to the modification of adhesive failure mechanisms, leading to a reduction in wear volume, improved coating adhesion, and enhanced scratch resistance.

Background. On the subject of couple relationships, the literature pays attention to clinical, socio-anthropological profiles and psychological issues related to the capacity to love, empathy, satisfaction and happiness; however, there is a lack of a psychometric tool that can address the issue of couple stability in a structured and organized manner from an emotional-affective perspective. Objectives. To develop and adjust a psychometric tool that can be efficient and effective in solving the analysis of a coefficient of couple relational stability. Materials and Methods. Clinical interview, based on narrative-anamnestic and documentary evidence, and battery of psychometric tests. Results. In CGa, those who scored more than 20% differential at PLS-Q1 were 58/118 (69%), while in CGb they were 118/118 (100%). In therapy, in the CGa, the resolved cases were 58/58 (100%), while in the CGb, the resolved cases were 110/118 (93%). At the clinical interview, it was found that the 8/118 (7%) "resistant" patients had, according to the PICI-3 model, a diagnosis of borderline personality disorder (5/8, 63%), histrionic-narcissistic (2/8, 25%), and bipolar (1/8, 12%), and thus by their nature not very prone to therapeutic adherence. Conclusions. Perrotta Love Stability Questionnaire (PLS-Q1) is a psychometric tool that offers therapists the opportunity to explore the topic of couple relationship stability, helping them to better focus on patients' vulnerable emotional positions to construct the most appropriate and targeted clinical intervention

Space instable target simulator (SITS) is a vital actuator for ground verification of on-orbital capture technology, the motion performance of which directly affects simulation credibility. Different delays reduce the stability of SITS and ultimately lead to its divergence. In order to achieve high fidelity simulation, the impact of force measurement delay, discrete control cycle, and simulator response delay on stability is analyzed firstly. Then, the dynamic equation and transfer function identification model of hybrid simulator is constructed, and the necessary and sufficient conditions of its stability and convergence are obtained using the Routh criterion. After that, a switching compensator with variable gain is proposed, the compensation principle diagram of which is build, and its mathematical model including the energy observer and tracking differentiator is also established. Finally, three sets of numerical simulations are conducted to validate the correctness of the stability analysis and effectiveness of proposed compensation method. Simulation results show that all three types of delay can cause SITS to lose stability under critical stable motion state, and the delay in force measurement has the greatest impact, followed by the influence of control cycle. Compared with the force applied to simulated target, velocity and its recovery coefficient of space instable target using fixed gain and linear gain compensation, the proposed compensator has significantly better performance.

Nickel-based Superalloy Inconel 718 is widely used in the aerospace industry for its excellent high-temperature strength and thermal stability. However, milling Inconel 718 presents challenges due to significantly increased cutting force and vibration, which is a typical difficult-to-machine material. This paper focuses on the milling process of Inconel 718, establishing a milling force model to analyze the force trends under various processing parameters. Finite element analysis is employed to study the stress and temperature fields during milling. Dynamic equations for milling Inconel 718 are developed, and stability lobe diagrams are generated based on modal experiments. Milling experiments on Inconel 718 validate the milling force model and finite element analysis results. The fmincon optimization algorithm is utilized to identify the optimal machining parameters for Inconel 718. Through this research, valuable insights into enhancing the efficiency and quality of Inconel 718 machining are provided. This study contributes to a deeper understanding of Inconel 718 milling behavior, offering crucial guidance for more efficient machining processes.

This article aims to discuss, the stability and boundedness character of the solutions of the rational equation of the form \begin{equation}\label{eql21.1} y_{t+1}=\frac{\nu\epsilon^{-y_t}+\delta\epsilon^{-y_{t-1}}}{\mu+\nu y_t+\delta y_{t-1}},\quad t\in N(0). \end{equation} Here, $\epsilon>1, \nu,\delta,\mu\in (0,\infty)$ and $y_0, y_1$ are taken as arbitrary non-negative reals and $N(a)=\{a,a+1,a+2,\cdots \}$. Relevant examples are provided to validate our results. The exactness is tested using MATLAB.

Immobilization of enzymes is a good field of study to expand the life of enzyme in and lowering the cost of the chemical processes such as separation processes. Urease is an important enzyme with medical and industrial applications. The aim of the present study is to prepare an immobilized urease on a strong cation exchange resin (Amberlite IR120 -Na) and study of its activity and stability. We monitored the liberation of Na ions in the collected fractions and searching for protein in the fractions as an indicators of immobilization by ion exchange phenomenon. Sodium is measured using atomic absorption spectroscopy techniques, while protein tested by Bradford’s method. Immobilized urease activity was evaluated by salicylate-hypochlorite method. The results indicated a complete immobilization of urease enzyme on the resin surface with reserving 92% of the activity of free enzyme. The immobilized urease enzyme on resin showed good stability and it has a 62% of its activity after 154 days of storage at room temperature. It is concluded that a new immobilized urease enzyme system is prepared with good enzyme activity and stability.

In this paper, we investigate the equilibrium points of following a system of difference equations x_n+1 = x_n 2y_n−1, y _n+1 = y_n 2x_n−1. We also study the asymptotic stability of related system of difference equations. Further we examine the periodic solutions of related system with period two. Additionally, we find out the invariant interval and periodic cycles of related system of difference equations.

The paper presents an innovative hexapod walking robot built with 3-UPU parallel mechanism. In the robot, the parallel mechanism is used as both an actuator to generate walking and also a connecting body to connect two groups of three legs, thus enables the robot to walk with simple gait by very few motors. In the paper, the forward and inverse kinematics solutions are obtained. The workspace of the parallel mechanism is analyzed using limit boundary search method. The walking stability of the robot is analyzed, which yields the robot’s maximum step length. The gait planning of the hexapod walking robot is studied for walking on both flat and uneven terrains. The new robot, combining the advantages of parallel robot and walking robot, has a large carrying capacity, strong passing ability, flexible turning ability, and simple gait control for its deployment for uneven terrain.

Many approaches have been developed over time to counter the bioavailability limitations of poorly soluble drugs. With advances in nanotechnology in recent decades, science and industry have been approaching this issue through the formulation of drugs as nanocrystals, which consist of pure drugs and a minimum of surface active agents required for stabilization. They are carrier-free submicron colloidal drug delivery systems with a mean particle size in the nanometer range, typically between 10 and 800 nm. By reducing particle size to nanoscale, the particle surface area available for the molecule dissolution in the direction of dissolution medium is increased, and thus bioavailability is enhanced. This approach has proven successful, as demonstrated by the number of such drug products on the market. R&D and industry have offered many technological solutions to reduce the particle size to nanoscale, and also devised solutions for the handling of particle of nanodimensions, such as methods to accurately measure nanoparticle size and techniques to prevent physicochemical and stability related problems, such as aggregation. The present work provides an overview of the more recent achievements in improving the bioavailability of poorly soluble drugs according to their administration route, and describes the methods developed to overcome physicochemical and stability related problems.

Novel high energy density materials N14 (1,6-dihydro-1,2,3,3a,4,5,5a,6,7,8,8a,9,10,10a-tetradecazapyrene) and N18 (1,2,2a,3,4,4a,5,6,6a,7,8,8a,9,10,10a,11,12a-octadecazacoronene) were designed, and their structures, detonation performance and stabilities were calculated employing density functional theory (DFT). Calculations reveals that they have a good balance between high energy and stability. Their energy gaps between LUMO and HOMO are all lower than that of TATB, while their impact sensitivity h_50% is estimated close to that of RDX. Concerning energy, detonation performance of the N14 (P = 43.6 GPa, D = 10040 m/s, Q = 2214 cal/g) and the N18 (P = 37.4 GPa, D = 9400 m/s, Q = 2114 cal/g) are comparable to CL-20.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

Drug nanosuspensions offer a promising approach to improve bioavailability for poorly soluble drug candidates. Such formulations often necessitate the inclusion of an excipient to stabilize the drug nanoparticles. However, a rationale to choose the correct excipient for a given drug candidate remains unclear. To gain molecular insight into formulation design, this work first utilizes molecular dynamics simulation to computationally investigate drug-excipient interactions for a number of combinations that have been previously studied experimentally. We find that hydrophobic interactions drive excipient adsorption to drug nanoparticles, and that the fraction of polar surface area serves as a predictor for experimental measurements of nanosuspension stability. To test these ideas prospectively, we applied our model to an uncharacterized drug compound, GDC-0810. Our simulations predicted that salt forms of GDC-0810 would lead to more stable nanosuspensions than the neutral form; therefore, we tested the stability of salt GDC-0810 nanosuspensions and found that the salt form readily formed nanosuspensions even without excipient. To avoid computationally expensive simulations in the future, we extended our model by showing that simple, two-dimensional properties of the single drug molecule can be used to rationalize nanosuspension design without simulation. In all, our work demonstrates how computational tools can provide molecular insight into drug-excipient interactions, and aid in rational formulation design.

In this paper, it is proved that s-iteration with error and Picard-Mann iteration with error iterative processes converge strongly to the unique fixed point of Lipschitzian strongly pseudo-contractive map. This convergence is almost -stable and -stable. Applications of these results to the operator equations, where is a strongly accretive and accretive mappings of into itself.

The studied Khanbogd pluton of peralkaline granite is located in southern Mongolia and occupies an area of ~1000 sq. km. Previously, two ring-shaped bodies were constructed in a flattened shape pluton. However, this shape was not used for the genesis of this pluton. A recent study of Landsat image showed a several elliptical intrusions in two bodies. Chemistry interpretation shows that each intrusion differs in ASI, CIPW norms, 87Sr/86Sri and δ18O isotopes. Elliptical intrusions, uplifted country rocks between them, and roof pendants suggest magma penetration along fractured country rocks. Furthermore, two adjacent intrusive bodies and undeformed host rocks at the front part of the pluton are consistent with underplating magmatic factors during duplex-type thrusting. This magma event is also supported by low of Sr, Ba, Eu and high of Th, U, Pb anomalies and a few amount of garnet crystals in the granites, implying vapor absent melt crystallization associated with underplating. Multiple melt sources, as well as from mantle and recycled sea floor rocks, are identified by ratio of 87Sr /86Sri and δ18O values. The low isotope values, the thrust nature and 295–286 Ma ages of the alkali granites, indicate an underplate magma evidenced during Permian rifting.

We previously showed that feeding mice a diet containing 1% mantle tissue decreased food consumption, leading to death. We also isolated and identified toxic substances in the mantle tissue. In the present study, we investigated the characteristics and stability of mantle tissue toxicity. Treatment of mantle tissue with 1 mM HCl, 1 mM NaOH, 1 mM dithiothreitol, and 1 mM H2O2 and heating did not reduce the toxicity of mantle tissue in mice. These results suggest that mantle toxins are stable in tissues, particularly when exposed to acidic and digestive enzymes. We examined whether mantle tissue exhibited acute toxicity. Diets containing 1% and 20% mantle extract showed similar levels of toxicity, demonstrating that feeding of mantle tissue does not lead to acute toxicity. Finally, we examined the toxicity of the mantle tissue against small intestinal tissue. Chronic feeding of mantle tissue to mice changed the color of the small intestine. Real-time PCR analysis showed that mantle tissue feeding caused changes of inflammation and endoplasmic reticulum stress markers in the small intestine. These results suggest that feeding of mantle tissue causes toxicity after causing initial damage to the small intestinal tissue.

3D metal nanostructures are often the basis of several applications such as in catalysis, plasmonics, medical diagnosis, therapy, drug screening, ophthalmologic, and biomedical applications. Porous gold nanoparticles (PGNs) are intensively investigated due to their outstanding morphological as well as advantageous optical properties. Unfortunately, the thermal stability of these open-porous structures is poor, i.e. even as a result of low-temperature annealing (150$^\circ$C in air), their porosity disappears and they lose their favorable optical properties. In order to preserve their beneficial properties, a thin metal oxide coating can be applied. Changing the coating's thickness and/or composition, the optical response of the PGNs can also be tuned in a wide wavelength region. Moreover, these nanoparticles can be synthesized also in support-free form, which makes them more attractive from an application point of view. This review article summarizes some of the preparation modes of these complex nanostructures (fixed and support-free), as well as their thermal stability and optical responses.

Cream cheese presents a favorable environment for the growth of pathogenic and spoilage microorganisms. The antimicrobial and antioxidant effects of plant extracts are well known, but their use is limited because they affect the physicochemical and sensory characteristics of products. Encapsulation presents an option to limit or prevent these changes. The paper presents the composition of individual polyphenols (HPLC–DAD-ESI-MS) from basil extracts (BE) with significant antioxidant activity (644.75±21.37 mM Trolox/g DW) and inhibitory effect against strains of Staphylococcus aureus, Geobacillus stearothermophilus, Bacillus cereus, Candida albicans, Enterococcus faecalis, Escherichia coli, and Salmonella Abony. The basil extract was encapsulated in sodium alginate (Alg) using the drop technique. The encapsulation efficiency of microencapsulated basil extract (MBE) was 78.59±0.01%. SEM and FTIR analyzes demonstrated the existence of weak physical interactions between the components. In the optimal concentration range of 0.6-0.9% MBE determined the inhibition of the post-fermentation process and the improvement of the degree of water retention. This led to the improvement of the textural parameters of the cream cheese, contributing to the extension of the shelf life of the product by 7 days. The influence of storage period and MBE concentration on texture parameters, pH and sensory analysis (overall acceptability) were evaluated by mutual information analysis.

The stick-free flight stability is an old-fashioned and non-progressive issue; nevertheless, it is still existent, and of significant importance to the design of aircraft whose control system is reversible. The problem’s existence necessitates a deep assessment of stick-free flight stability throughout the aircraft design. Up to now, this problem has been addressed using either analytical approaches, which are only related to the static stability evaluation, or performing flight tests. In this study, the problem is handled in its entirety, from static and dynamic flight stability assessment to design criteria with a comprehensive perspective. Moreover, it is also exhibited that contrary to what has been generally proposed in the literature, limiting the problem of stick-free flight stability through static stability assessment is far from the main challenge. As a brief scope, the derivation of the control surface dynamics, a stick-free trim algorithm, and assessment rationale of the stick-free static and dynamic flight stability using a simulation approach are proposed. As a consequence, the aim is to set a broad understanding for designers related to this phenomenon and add adjunct design criteria in the design optimization process by approaching it in terms of modeling, simulation, and flight test perspective.

Pomegranate extract (PG-E) has been reported to exert a protective effect in skin due to its antioxidant activity. Ingredients rich in phenolic compounds are unstable in extract solutions and, therefore, the use of a suitable nanosystem to encapsulate this type of extract could be necessary in different biotechnological applications. Thus, we investigated the capacity of Brassica oleracea L. (cauliflower) inflorescence vesicles (CI-vesicles) to encapsulate PG-E and determined the stability and the antioxidant capacity of the system over time. In addition, the protective effect against UV radiation and heavy metals in HaCaT cells was also tested. The CI-vesicles had an entrapment efficiency around 50% and accelerated stability tests did not show significant changes in the parameters tested. The results for the HaCaT cells show the non-cytotoxicity of the CI-vesicles containing PG-E and their protection against heavy metals (lead acetate and mercuric chloride) and UV-B radiation through a reduction of oxidative stress. The reduction of the percentage of deleted mtDNA (mtDNA4977, “common deletion”) in UV-treated HaCaT cells due to the presence of CI-vesicles containing PG-E indicates the mechanism of protection. Therefore, the effects of CI-vesicles loaded with PG-E against oxidative stress support their utilization as natural cosmeceuticals to protect skin health against external damage from environmental pollution and UV radiation.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

Menaquinone-7 is a member of the vitamin K family whose interest has considerably increased over the last decade due to its beneficial role in human health mainly in respect to bone and cardiovascular health leading to a growing use in different nutritional supplement. Menaquinone-7 can be produced by synthesis or fermentation and its purity profile can differ depending on methodologies and extraction procedures. Finished formulation show a large heterogeneity of purity profiles as well as frequent discrepancies in the nominal content compared to the actual title. In the present study we compared purity profiles of different raw material and we related them to stability assay in normal (12months/25°C/60%RH) and accelerated conditions (6 months/40°C/75% RH) in order to test their performance in presence of different common excipients. Results show that higher purity profile correlates with enhanced stability and this could explain title discrepancies found in finished products found on the market worldwide.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

This paper investigates the dynamic properties of artificial neural networks using differential equations and explores the influence of parameters on stability and neural oscillations. By analyzing the equilibrium point of the differential equations, we identify conditions for asymptotic stability and criteria for oscillation in artificial neural networks. Furthermore, we demonstrate how adjusting synaptic weights between neurons can effectively control stability and oscillation. The proposed model offers potential insights into the malfunctioning mechanisms of biological neural networks implicated in neurological disorders like Parkinson's disease tremors and epilepsy seizures, which are characterized by abnormal oscillations.

Antigen-based rapid diagnostic tests for Lymphatic filariasis do not come with quality control (QC) materials, and research and disease control programmes rely on stored positive plasma samples. This study was undertaken to evaluate the use of freeze-dried Wuchereria bancrofti antigen positive plasma samples to serve as QC materials for LF RDTs. 10 well characterized W. bancrofti positive samples were lyophilized and stored at 4°C, 28°C and 40°C. The samples were evaluated using the Filaria Test Strips before lyophilization and after one and three (3) months of storage. The sensitivity and stability of the lyophilized samples were evaluated. The results revealed a loss of sensitivity and stability with increasing temperature and duration of storage. The results are further discussed in terms of the use of Dried Blood Spot (DBS) in diagnostics studies on LF requiring quantitative assessments, and the need for thoughtful DBS preparation and storage.

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

DNA damage causes the mutations that are the principal source of genetic variation. DNA damage detection and repair mechanisms therefore play a determining role in generating the genetic diversity on which natural selection acts. Speciation, it is commonly assumed, occurs at a rate set by the level of standing allelic diversity in a population. The process of speciation is driven by a combination of two evolutionary forces: genetic drift and ecological selection. Genetic drift takes place under conditions of relaxed selection, and results in a balance between rates of mutation and rates of genetic substitution. These two processes, drift and selection, are necessarily mediated by a variety of mechanisms guaranteeing genome stability in any given species. One of the outstanding questions in evolutionary biology concerns the origin of the widely varying phylogenetic distribution of biodiversity across the tree of life, and how the forces of drift and selection contribute to shaping that distribution. The following examines some of the molecular mechanisms underlying genome stability and the adaptive radiations that are associated with biodiversity and the widely varying species richness and evenness in the different eukaryotic lineages.

In recent years the yield of fruits and vegetables have been decreasing in Colombia, threatening national food security. Analysis of crop production data may lead to identifying cropping systems that have shown better adaptability to changes in climatic and non-climatic factors associated with agricultural production. The open database AGRONET keeps data of the agricultural activities conducted in Colombia, allowing to find the information organized by crops, regions and years; each row of the database registers farm information in Colombia. Aiming to identify resilient crops systems, agricultural data of fruits and vegetables were analyzed. First, trends in crop production were studied by year and locations, detecting the regions and crops with highest yields in the period from 2006 until 2020. Then, mixed linear regression and principal components analysis were applied to elucidate the relation between non-climatic factors and crop yield. In Colombia, vegetable production was more efficient than fruits, observing yields of 10.23 and 13.33 t ha^-1, respectively. On the other hand, the Colombian central region showed high yields for vegetables, while for fruits this was exhibited in northern and eastern locations. In the present study, yield variation responded to changes in the location of crop systems, while years had no effect on vegetable production. Furthermore, the price of the agricultural product and the cost of fertilizers were associated with the yield of the analyzed crops systems. In Colombia, carrot, cabbage, tomato papaya and pineapple are resilient crops whose yield increases especially by the regions where they are cultivated.

Recently, there has been a lot of interest in the phenolics of pomegranate peels because of their health-promoting effects. The incorporation of encapsulated phenolic extracts in functional foods, beverages, and dietary supplements can enhance their nutritional and health benefits. This paper aims to provide an overview of the encapsulation of pomegranate peel phenolic extract by co-crystallization, focusing on the properties of the encapsulated extract. Pomegranate peel extract encapsulated in sucrose by co-crystallization at conditions determined in our previous work is characterized by evaluating its properties; moisture content, bulk density, solubility, hygroscopicity, color, degree of encapsulation by thermograms, crystallinity by X-ray scattering, microstructure by scanning electron microscope, and storage stability in terms of total phenolic content and antioxidant activity. The co-crystallized powder had a low moisture content (0.59%) and hygroscopicity (0.011%) and a high bulk density (0.803 g/cm3) and solubility (61 s). Its total phenolic content decreased by only 0.56% after storage at 60oC for 45 days, whereas its antioxidant activity was maintained at levels higher than 84%. The differential scanning calorimetry and the X-ray scattering techniques proved the successful encapsulation in the sucrose matrix and the fact that the extract remained liquid inside the porosity of the sucrose crystals.

Incremental stability analysis for time-delay systems has attracted more and more attentions for its contemporary applications in transportation processes, population dynamics, economics, satellite positions, etc. This paper researches criteria on v(t)-incremental stability, which is defined to demonstrate the convergence rate for incremental stability, for time-delay systems. Firstly, the sufficient conditions for v(t)-incremental stability for time-delay systems with continuous right-hands are studied, and several corollaries for specific cases are provided. As for time-delay systems with discontinuous right-hands, after expounding the relevant conditions for the existence and uniqueness of the Filippov solution, by using approximation methods, sufficient conditions for v(t)-incremental stability are obtained. The conclusions are applied to linear switched time-delay systems and Hopfield neural network system with composite right-hand afterwards.

This research investigates a model for the COVID-19 outbreak in Indonesia by analyzing comorbid diseases, self-quarantine, government-provided quarantine, and immunization regimens. Some model parameters are derived from academic journals, others are extrapolated from data collected by the Indonesian Ministry of Health in 2020, and others are assumed. Evaluation of the model reveals non-endemic equilibrium points, endemic equilibrium points, and the basic reproduction number (BRN). The contact rate and infected probability factors impact the increase in the number of COVID-19-infected individuals with comorbid disease within a group. According to the sensitivity analysis of the BRN, the key parameters impacting the spread of COVID-19 are the rate of susceptible recruitment, the rate of contact, the COVID-19 infection death rate, and the likelihood of infection. In addition, sensitivity analyses are provided to examine the effect of parameter changes on subpopulations. We discovered that the natural death rate is the most sensitive parameter based on the sensitivity index after reaching equilibrium. Symmetry aspects appear in some of the visualization of the model’s solution and the BRN and parameters’ sensitivity.

This paper reports applying Minimax principle and impulsive differential inequality to derive the existence of multiple stationary solutions and the global stability of a positive stationary solution for a delayed feedback Gilpin-Ayala competition model with impulsive disturbance. The conclusion obtained in this paper reduces the conservatism of the algorithm compared with the known literature, for the impulsive disturbance is not limited to impulsive control.

Leishmania species are parasitic protozoans which cause leishmaniasis affecting millions of people worldwide. Sterols are important components of plasma and organellar membranes and serve as precursors for the synthesis of signaling molecules. In contrast to animals, Leishmania do not produce cholesterol but instead synthesize ergostane-based sterols. C14-demethylase is a key enzyme involved in the biosynthesis of sterols in Leishmania parasites and an important drug target. Its inactivation leads to multiple defects including increased plasma membrane fluidity, mitochondrion dysfunction, hypersensitivity to stress and reduced virulence. In this study, we revealed a novel role for sterol synthesis in the maintenance of RNA stability and translation. Sterol alteration in C14-demethylase knockout mutant leads to increased RNA degradation, reduced translation and impaired heat shock response. Thus, sterol biosynthesis plays an unexpected role in global gene regulation in Leishmania parasites.

This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

This paper presents sufficient conditions for almost global stability of nonlinear switched systems consisting of both stable and unstable subsystems. Techniques from the stability analysis of switched systems have been combined with the multiple Lyapunov density approach - recently proposed by the authors for the almost global stability of nonlinear switched systems composed of stable subsystems. By using slow switching for stable subsystems and fast switching for unstable subsystems lower and upper bounds for mode-dependent average dwell times are obtained. In addition to that, by allowing each subsystem to perform slow switching and using some restrictions on total operation time of unstable subsystems and stable subsystems, we have obtained a lower bound for an average dwell time.

The compatibility of graphene or graphene oxide with its dispersion medium (polymer) plays a critical role in the formation nanocomposite materials with significant property improvements. Environmentally friendly miniemulsion polymerization, which allows a formation of nanoencapsulation in an aqueous phase and high molecular weight polymer/composite production is one promising method. In this study, we screened a series of amphiphilic modifiers and found that the quaternary ammonium (ar-vinyl benzyl) trimethyl ammonium chloride (VBTAC) pending carbon double bonds could effectively modify the graphene oxide (GO) to be compatible with the organophilic monomer. After that, free radical miniemulsion polymerization could successfully synthesize stable latex of exfoliated poly (methyl methacrylate) (PMMA)/ GO nanocomposite. The final latex had an extended storage life and a relatively uniform particle size distribution. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) analysis of this latex and its films indicated successful encapsulation of exfoliated nano-dimensional graphene oxide inside a polymer matrix.

The degradation and detachment of the polyamide (PA) layer in thin-film composite (TFC) membranes due to chlorine based chemical cleaning and material difference of PA layer and substrate are two major bottlenecks of forward osmosis (FO) technology. In this study, a new type of FO membranes were prepared by controlling self-polymerization of dopamine (DA) in the aqueous phase and the reaction with trimesoyl chloride (TMC) during interfacial polymerization (IP) process. These membranes were characterized by attenuated total reflection Fourier transform infrared (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FESEM) and water contact angle measurements. The influence of synthesis parameters such as pH of the aqueous phase, reaction time, temperature, and monomer concentrations were systematically investigated. The optimized membrane showed enhanced structure stability in ethanol (7.1 times higher) and chlorine resistance (72.3 times higher) than the conventional Piperazine(PIP)/TMC membrane due to（poly-dopamine）PDA bio-adhesion and polyester groups in the membrane structure. In general, DA/TMC membranes could be an effective strategy to fabricate high-performance FO membranes with excellent structural stability and chlorine resistance.

Starting from the model of a slow-rolling missile with six degrees of freedom (6 DOF) in the body frame, a 6 DOF model in the Resal frame is obtained, which is used to linearize the coupled commanded motion. Based on the linearized model, we obtain the structural scheme of the commanded object and define the quality parameters. The obtained parameters have a complex representation (with real and imaginary parts) due to the coupling between longitudinal channels. Then, the kinematic guidance equations, the seeker equations and the actuator specific to the slow-rolling single-channel missile are defined using a switching function. The guidance kinematic equations, the seeker equations and the actuator model are linearized in the Resal frame, and the structural diagram of the homing missile is constructed. Starting from this, the characteristic polynomial having complex coefficients is determined and then analyzed with the Frank-Wall stability criterion. Based on the analysis, a stability range is determined for the navigation constant and a minimum and possibly a maximum limit for the time to hit the target is obtained. The stability range defined for the navigation constant on the linear model is finally validated on the nonlinear model in the body frame.

This paper aims to present the basic assumptions for creation of social Fröhlich condensate and attract attention of other researchers (both from physics and socio-political science) to the problem of modelling of stability and order preservation in highly energetic society coupled with social energy bath of high temperature. The model of social Fröhlich condensation and its analysis are based on the mathematical formalism of quantum thermodynamics and field theory (applied outside of physics). The presented quantum-like model provides the consistent operational model of such complex socio-political phenomenon as Fröhlich condensation. The model of social Fröhlich condensation is heavily based on theory of open quantum systems. Its consistent elaboration needs additional efforts. Evidence of such phenomenon as social Fröhlich condensation is demonstrated by stability of modern informationally open societies Approaching the state of Fröhlich condensation is the powerful source of social stability. Understanding its informational structure and origin may help to stabilize the modern society. Application of the quantum-like model of Frhlich condensation in social and political sciences is really the novel and original approach to mathematical modeling of social stability in society exposed to powerful information radiation from mass-media and internet based sources.

Cemented rock fill (CRF) is commonly used in cut-and-fill stoping operation in underground mining. This allows for the maximum recovery of ore. Backfilling can improve stope stability in underground workings, and then improve ground stability of the whole mine site. Backfilling step scenarios vary from site to site. This paper presents the investigation of five different backfilling step scenarios and their impacts on the stability of stopes at four different mining levels. A comprehensive comparison of displacements, major principal stress and stress concentration factor (SCF) was conducted. The results show that different backfilling step scenarios have little influence on the final displacement for displacement in the stopes. Among the five backfilling scenarios, the major principal stress and stress concentration factor (SCF) have almost the same final results. The backfilling scenario SCN-1 is the optimum option among these five backfilling scenarios. It can immediately prevent the increase of the displacement and reduce the sidewall stress concentration, thereby preventing possible failures. Using the same strength of CRF can achieve same effects among the four mining levels. Applying backfilling CRF of the same strength at different mining depths is acceptable and feasible to improve the stability of the stopes.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

The current work reveals the fine tuning between stability zones and randomness of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing D/M/1 system. More specifically, this clearly provides more insights into developing a contemporary PSFFA theory that unifies non-stationary queueing theory with chaos theory and fields in both theoretical physics and chaotic systems. This opens new grounds for stability analysis of non-stationary queueing systems.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Major depressive disorder (MDD) and generalized anxiety disorder (GAD) exert significant burdens on individuals and society, underscoring the importance of accurate predictions using advanced machine learning (ML) algorithms. Leveraging electronic health records (EHRs) and survey data, these algorithms offer potential in forecasting such mental health conditions. Yet, the precision of these predictions can be compromised by biases or inaccuracies inherent in subjective survey responses. In this research, we assess the reliability of four prominent ML algorithms—Random Forest, XGBoost, Logistic Regression, and Naïve Bayesian—in predicting MDD and GAD. Our dataset encompasses a rich array of information, from biomedical metrics and demographic details to self-reported survey insights. A focal point of our investigation is the algorithms' performance under scenarios with varying degrees of subjective response inaccuracies, such as memory recall biases or subjective interpretation. Our findings reveal that while all algorithms exhibit commendable accuracy with pristine survey data, their performance diverges when faced with erroneous or biased responses. Notably, XGBoost remains stable and excels in identifying true positive cases, even in the presence of such noise. These observations underscore the criticality of algorithmic resilience in mental health prediction, especially when relying on subjective data. The robustness of certain algorithms to noisy inputs positions them as more reliable choices for predicting mental health conditions based on self-reported data, emphasizing the need for careful algorithm selection in such contexts.

In this study, we deal with a nonlinear system of neutral Volterra integro-differential equations (NVIDEs) with infinite delay. We study stability, uniform stability and instability of zero solution of the system of NVIDEs with infinite delay. We obtain three new results with regard to these concepts via two new Lyapunov– Krasovskii functionals (LKFs), respectively. As the main contributions of this work, we improve and generalize some earlier results in the relevant database from the linear case to more general nonlinear cases.

This work studied sorption regularities and assessed thermal stability and resistance to microbial degradation of humic acid as a result of 3 sorption cycles on bentonite clay, kaolinite, and muscovite using TGA/DSC, XRD, hydrophobic chromatography, light and electron microscopy, etc. The experiment revealed that kaolinite sorbed more humic acids (HAs) in terms of unit surface area (1.03 × 10-3 C, g/m2) compared to bentonite (0.35 × 10-3 C, g/m 10-3 g/m2). Sorption at pH 4.5 was accompanied by HA fractionation in amphiphilicity and chemical composition. HA was sorbed mainly due to hydrophobic components on the surface of all sorbents. HA was not intercalated into the interlayer spaces of montmorillonite during sorption. Sorption due to hydrophilic interactions was mostly performed on muscovite and bentonite than on kaolinite. Sorption was followed by a change in the chemical composition of HA and decreased C/N compared to free HA, indicating selective sorption of nitrogen-containing compounds which is most characteristic of muscovite. Only a relatively thermolabile HA fraction was adsorbed on all minerals while its thermal stability increased compared to that before the experiment. Thermal stability and ratio of the Exo2/Exo1 peak areas on the DSC curves of sorbed HA increased with each subsequent sorption cycle. Thermal stability and resistance to microbial oxidation of sorbed HA showed the following relationship: the higher the thermal stability, the less available is sorbed HA for utilization by microorganisms.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

By defining a constant probabilistic orbit of and iterated functions, the stability dynamics of these functions in possible interactions through connectivity provides the formation of a dynamic fixed point as a metric space between both iterated functions. The presence of a dynamic fixed point identifies qualitatively phases of iteration time lengths and interaction orbits of the event. Qualitative results show that the greater the average distance from one of the functions to the fixed point of the other (all possible solutions), the higher the iteration expression on time (false asymptotic effect) of one of the functions and in the opposite hand, the lower the average distance, the higher orbit’s interactions proximity between iterated functions (stability). This feature reveals asymptotic (well-defined) behavior between functions f and g within a well-defined Lyapunov stability.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

The sustainability of irrigated agriculture depends on the quality of irrigation water used. The electrolyte concentration (EC) of irrigation water may lead to the accumulation of salts in the root zone layers and affect the physiological functions of the crop by osmotic and ion toxicity effects. Further, the cationic and anionic composition of the water may alter the exchangeable cation composition of the soil and as well as its pH. Because of the dominance of sodium salts in many sources of irrigation water, parameters related to sodium such as exchangeable sodium percentage (ESP) of soils and sodium adsorption ratio (SAR) of soil solutions have been commonly used to study the effects of sodium in irrigation water on soil structural stability. Quirk and Schofield concept of ‘threshold electrolyte concentration’ (TEC) has shown the importance of electrolytes in preventing the effects of sodium on soil structure. Based on this concept, several models have been proposed to relate ESP or SAR with EC to predict the possible impacts of irrigation water on soil structural stability. However, many research reports indicate that this relationship varies with soils and a given model is not suitable for all types of soils. Further, the effects of potassium and magnesium in the processes leading to clay dispersion are disregarded in these models. This essay analyses all the factors involved in the structural failure of soils with different cationic composition, identify the defects in these TEC models and re-defines TEC on the basis of new insights on dispersive and flocculating charges of soils. This review does not deal with EC effects on crops and also the role of contaminant ions not involved with soil structural stability.

This paper is a study of a generalization of the quantum Riemannian Hamiltonian evolution, previously analyzed by us in our work [6], in the geometrization of quantum mechanical evolution in a Finsler geometry. We find results with dynamical equations governing the evolution of the trajectories defined by the expectation values of position. The analysis appears to provide an underlying geometry described by a geodesic equation, with connection form with a second term which is an essentially quantum effect. These dynamical equations provide a new geometric approach to the quantum evolution where we suggest a definition for "local instability" in the quantum theory.

The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.

Studies on the long-term stability of meat analogs stored under frozen conditions are lacking. Here, we aimed to assess the storage stability of vegetable oil-supplemented meat analogs and analyze the effects of temperature and storage period on their physiochemical characteristics. The meat analogs were prepared by adding 30 g castor oil, orange oil, palm oil, shortening, or margarine vegetable oil based on 100 g of textured vegetable protein. They were then stored at −18 or −60 °C for 6 months and analyzed at one-month intervals. The meat analog supplemented with orange oil had the highest water content, liquid-holding capacity, hardness, and antioxidant activity. During frozen storage, temperature barely affected the meat quality. The storage stability of all meat analog samples was maintained for 6 months, although the quality was slightly reduced with an increase in storage duration. Coliform group bacteria were not detected regardless of the storage condition. Orange oil improved the juiciness of meat analogs, and the quality of samples was maintained for at least 6 months under frozen storage. The findings of this study are relevant to the development and promotion of vegetable meat as an alternative to animal meat.

Objective: To evaluate the physical and chemical stability of the antibiotic temocillin at the recommended dose for severe infections and contained in infusion bags or elastomeric devices at different temperatures for its use in Outpatient Parenteral Antimicrobial Therapy (OPAT) programs.Method: Solutions of temocillin 12 g/L diluted in 0.9% sodium chloride were stored at 4ºC ± 2ºC, 25°C ± 2°C, 32°C ± 2°C and 37°C ± 2°C for 72 h both in polypropylene infusion bags and in polyisoprene elastomeric pumps. Physical and chemical stability were evaluated at 12, 24, 30 48 and 72 h after manufacturing. The solutions were considered stable if color, clearness and pH remained unchanged and if the percentage of intact drug was ≥90%. Results: There were no observed changes in color or clarity in any of the refrigerated (4°C) samples or in the samples incubated at 25ºC and 32ºC. At 37ºC, an increase in intensity of yellow color was observed at 30, 48 and 72 h in both infusion bags and elastomeric pumps samples. All samples remained within the pH range 6.84–6.06. At 4ºC, 25ºC and 32°C ± 2°C, temocillin attained the stability criteria of ≥90% of the original concentration for the whole experiment in both devices. At 37ºC, temocillin was stable for 24 h but its concentration dropped below 90% from that time point both in the infusion bags and in the elastomeric pumps.Conclusions: According to the data provided in this stability study, temocillin administrated by continuous infusion would be an appropriate candidate for the treatment of patients that can be discharge to complete therapy in an OPAT program.

In this paper, impulsive control on a single-species Markovian jumping ecosystem leads to a stability criterion, and the newly-obtained theorems improve the related existing results. Numerical examples illuminate the effectiveness.

We firstly discuss classical stability for a dynamical system of two ions levitated in a 3D Radio-Frequency (RF) trap, assimilated with two coupled oscillators. We obtain the solutions of the coupled system of equations that characterizes the associated dynamics. In addition, we supply the modes of oscillation and demonstrate the weak coupling condition is inappropriate in practice, while for collective modes of motion (and strong coupling) only a peak of the mass can be detected. Phase portraits and power spectra are employed to illustrate how the trajectory executes quasiperiodic motion on the surface of torus, namely a Kolmogorov-Arnold-Moser (KAM) torus. In an attempt to better describe dynamical stability of the system, we introduce a model that characterizes dynamical stability and the critical points based on the Hessian matrix approach. The model is then applied to investigate quantum dynamics for many-body systems consisting of identical ions, levitated in 2D and 3D ion traps. Finally, the same model is applied to the case of a combined 3D Quadrupole Ion Trap (QIT) with axial symmetry, for which we obtain the associated Hamilton function. The ion distribution can be described by means of numerical modeling, based on the Hamilton function we assign to the system. The approach we introduce is effective to infer the parameters of distinct types of traps by applying a unitary and coherent method, and especially for identifying equilibrium configurations, of large interest for ion crystals or quantum logic.

The load on the top of a slope is an important cause of slope failure, and it is of great significance to study the relationship between the load and the stability of the slope. This paper uses elastic theory and Moore Coulomb's theory as transformation conditions to obtain the slope stability coefficient expression under slope top load based on the Swedish slice method. In view of the actual engineering, the corresponding slope model structure was established, and 5 sliding surfaces were set with the crack on the top of the slope as the shear outlet. According to the slope stability coefficient expression, the stability coefficient of the set sliding surface is solved. The result shows that the slope is unstable under the load. The judgment result is consistent with the GEO-STUDIO check calculation result. This method can provide reference for theory and engineering practice.

Stability considerations play a central role in structural dynamics to determine states that are robust against perturbations during the operation. Linear stability concepts, such as the complex eigenvalue analysis, constitute the core of analysis approaches in engineering reality. However, most stability concepts are limited to local perturbations, i.e. they can only measure a state’s stability against small perturbations. Recently, the concept of basin stability has been proposed as a global stability concept for multi-stable systems. As multi-stability is a well-known property of a range of nonlinear dynamical systems, this work studies the basin stability of bi-stable mechanical oscillators that are affected and self-excited by dry friction. The results indicate how the basin stability complements the classical binary stability concepts for quantifying how stable a state is given a set of permissible perturbations.

Short chain quinones (SCQs) have been identified as potential drug candidates against mitochondrial dysfunction, which is largely dependent on their reversible redox characteristics of the active quinone core. We recently synthesized a SCQ library of > 148 naphthoquinone derivatives and identified 16 compounds with enhanced cytoprotection compared to the clinically used benzoquinone idebenone. One of the major drawbacks of idebenone is its high metabolic conversion in the liver, which significantly restricts is therapeutic activity. Therefore, this study assessed the metabolic stability of the 16 identified naphthoquinone derivatives 1-16 using hepatocarcinoma cells in combination with an optimized reverse-phase liquid chromatography (RP-LC) method. Most of the derivatives showed significantly better stability than idebenone over 6 hours (p < 0.001). By extending the side-chain of SCQs, increased stability for some compounds was observed. Metabolic conversion from the derivative 3 to 5 and reduced idebenone metabolism in the presence of 5 were also observed. These results highlight the therapeutic potential of naphthoquinone-based SCQs and provide essential insights for future drug design, prodrug therapy and polytherapy, respectively.

Static standing postural stability has been measured by multiscale entropy (MSE), which is used to measure complexity. In this study, we used the average entropy (AE) to measure the static standing postural stability, as AE is a good measure of disorder. The center of pressure (COP) trajectories were collected from 11 subjects under four kinds of balance situation, from stable to unstable: bipedal with open eyes, bipedal with closed eyes, unipedal with open eyes, and unipedal with closed eyes. The AE, entropy of entropy (EoE), and MSE methods were used to analyze these COP data, and EoE was found to be a good measure of complexity. The AE of the 11 subjects sequentially increased by 100%as the balance situations progressed from stable to unstable, but the results of EoE and MSE did not follow this trend. Therefore, AE, rather than EoE or MSE, is a good measure of static standing postural stability. Furthermore, the comparison of EoE and AE plots exhibited an inverted U curve, which is another example of a complexity versus disorder inverted U curve.