The rapid convergence of Artificial General Intelligence (AGI), autonomous drones, and applied robotics presents a transformative opportunity for many sectors. However, this advancement also raises critical ethical and existential questions, particularly in warfare. This paper explores the concept of entropy as a metaphor for the potential disorder introduced by these increasingly complex technologies. We examine the risks of AGI surpassing human control in conflict situations, where autonomous decision-making could have disastrous consequences. We then analyze autonomous drones, scrutinizing their impact on warfare tactics and the ethical dilemmas surrounding independent, real-time decision-making. Finally, we investigate applied robotics in military operations, focusing on the delicate balance between enhanced capabilities and the potential for uncontrollable systems. Through a multidisciplinary lens, drawing on technology ethics, military strategy, and AI safety, this paper utilizes the concept of entropy to highlight the need for caution in developing these technologies. We propose a scientifically grounded and ethically sound framework to guide policymakers, technologists, and ethicists in navigating the path between innovation and global stability. This framework concludes with recommendations for responsible development and deployment strategies that can mitigate the risks associated with these powerful tools.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

This paper presents MADS (Multi-Agents for Data Science), an innovative and simple open-source multi-agent framework designed for systemic pipeline execution in applied supervised machine learning. By leveraging the capabilities of multi-agent systems (MAS), we introduce a universal approach to optimize and streamline machine learning pipelines. Our framework highlights the differences between various types of agents, such as reinforcement learning (RL) agents and large language model (LLM) agents, and their distinct contributions to the process. While we currently employ LLM agents to automate and enhance machine learning tasks, we acknowledge the potential of incorporating RL agents in future iterations to further improve performance and adaptability. The primary objective is to enhance the efficiency, scalability, and adaptability of supervised learning applications across various domains. This integration addresses the complexity and manual effort typically associated with machine learning workflows, paving the way for more automated, robust, and scalable solutions. Our approach demonstrates significant improvements in task automation, reduced human intervention, and enhanced model performance. The MADS framework, which will soon be available as an open-source implementation, represents a pivotal contribution to the field of machine learning, promising to facilitate broader adoption and collaborative advancement.

Ultrasonic transducers are widely used for non-destructive testing (NDT) and evaluation in various industries. While capacitive micromachined ultrasonic transducers (CMUTs) have emerged as significant novel transducers, their application in NDT has been limited. This study designed and fabricated a novel two-element CMUT device for NDT applications. The CMUT’s structural parameters were introduced, and the device was fabricated using silicon fusion wafer-bonding technology. The transducer’s sensitivity, bandwidth, and pulse-echo response performance were tested and analyzed. Testing with aluminum blocks demonstrated that the two-element transducer can transmit and receive ultrasonic waves, with central operating frequencies of 3.35 MHz. In addition, at 3.4 MHz, the receive sensitivities of both elements were –197.434 dB and –197.413 dB, respectively, meeting the requirements for NDT systems. In pulse-echo response testing, the CMUT successfully detected signals from the aluminum block interface and located the interface’s position. This study highlights the potential of CMUTs for NDT testing and evaluation applications.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

We propose a pricing formula for a defaultable zero-coupon bond with imperfect information under a regime-switching model using a structural form of credit risk modelling. While the value of the firm’s equity is observed continuously, we assume that the total value of the firm is only observed at discrete times, such as the dates of the release of the firm’s annual reports, or quarterly reports. This uncertainty about the true value of the firm results in credit spreads that do not approach zero as the debt approaches maturity, which is a problem with many structural models. The firm’s value is typically defined as its equity and debt; however, we consider the asset-to-equity ratio, an accounting ratio used to examine a firm’s financial well-being. A dependent regime-switching process models the components of this ratio, and the Markov chain represents the states of the economy. The main contribution is to study this problem when the dynamics of a firm’s assets have different parameters with regime changes.

To enhance the peak-shaving capability of the boiler, a mathematical model of hydrodynamic and wall temperature characteristics for the water-cooled wall of a 1000 MW boiler was established. The attributes pertaining to the mass flow distribution, the temperature of the effluent working fluid, pressure drop, and the thermal distribution across the wall surfaces at 30% of the boiler's maximum continuous rating (BMCR) were meticulously computed and subjected to a thorough analytical review. The findings suggest that, under the operation at 30% BMCR load, there is a substantial equilibrium in the flow distribution across the quartet of walls that constitute the water-cooled wall assembly. The maximum mass flow rate deviations in the helical and vertical sections are 1.95% and 3.47%, respectively, showing small flow deviations and reasonable distribution. The temperature deviation in the helical section is 0.3 °C, reflecting the characteristic low thermal deviation in helical tubes. While the temperature deviation at the outlet of the vertical section is higher, it remains within safe limits. The pressure loss across the water-cooled wall system amounts to 0.4 MPa. The peak wall temperature reaches 337.5°C, remaining within the material's permissible safety limits. In-depth performance analysis ensures the safe operating conditions of the water-cooled wall during low load conditions.

Drought affects human and natural systems, human and animal life and health, and socioeconomic activities. Drought consequences depend on its type and class, but also on the preparedness and resistance of communities to this climate disturbance. In the last decades, droughts accounted for about 16% of the total number of disasters but were responsible for 95% of the number of deaths and 26% of economic losses in Africa. This study aims to assess the drought regime in Southern Africa based on drought and vegetation indices. The SPI and SPEI were calculated at different timescales, using ERA5 data for the 1971 – 2020 period. The spatiotemporal distribution of drought descriptors was analyzed and compared with the patterns of the NDVI, EVI and VCI vegetation indices. The results reveal (i) the occurrence of droughts of various classes and at different timescales throughout the study period and region, (ii) high spatial variability in the number, duration, severity and intensity of drought, which tends to decrease with increasing timescale, (iii) high spatial-temporal agreement between drought and vegetation indices that confirm the dryness of vegetation during drought. These results aim to support policymakers in defining legislation to manage drought and water resources.

Every simplification has the potential to add a systematic error to the measured value. Sometimes, the addition does not render the measurement useless. In the case of oil well flow measurements based on the thermal properties of the fluid in the well, the addition of a systematic error of up to 20% can occur if the variation in the internal energy of the fluid and, most importantly, the transient nature of heat transfer in the completion are not taken into account. This error is a mathematical consequence of the simplifications chosen. To work within the first hours of good operation, given the need for immediate application in a prototype water injection well developed and installed at the UFRN, this article presents an analytical solution for calculating the flow rate by solving the differential equations obtained by applying the principles of mass and heat transfer. As a result, at the cost of greater complexity, the systematic error drops to values of less than 1% in the first two hours of operation of the well, as seen throughout this document.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

This paper presents a robust method based on graph topology to find the topologically correct and consistent subset of inter-robot relative pose measurements for multi-robot map fusion. However, the absence of good prior gives a severe challenge to distinguish the inliers and outliers, and wrong loop closures can seriously corrupt the fused global map. Existing works mainly rely on the consistency of spatial dimension to select inter-robot measurements, which does not always hold. In this paper, we propose a fast inter-robot loop closure selection method that integrates the consistency and topology relationship of measurements, which both conform to the continuity characteristics of similar scenes and spatiotemporal consistency. The traditional high-dimensional consistency matrix is decomposed into the sub-matrix blocks corresponding to the overlapping trajectory area. Building on this logic, a clustering method involving topology correctness of inter-robot loop closures is introduced to split the entire measurement set into multiple clusters. We define the weight function to find the maximum cardinality subset with topologically correct and consistent, then convert the weight function to a maximum clique problem in the graph and solve it. We evaluate the performance of our method in a simulation and in a real-world experiment. Compared to state-of-the-art methods, the results show that our method can achieve competitive performance in accuracy while reducing computation time by 75%.

An approach based on the OpenFOAM library has been developed to solve a high-speed, multicomponent mixture of a reacting, compressible flow. This work presents comprehensive validation of the newly developed solver called compressibleCentralReactingFoam with different supersonic flows, including shocks, expansion waves, and turbulence-combustion interaction. The comparisons of the simulation results with experimental and computational data confirm the fidelity of this solver for problems involving multicomponent high-speed reactive flows. The gas dynamics of turbulence-chemistry interaction are modeled using a partially-stirred reactor formulation and provide promising results to better understand the complex physics involved in supersonic combustors. A time-scale analysis based on local Damköhler numbers reveals different regimes of turbulent combustion. In the core of the jet flow, the Damköhler number is relatively high indicating that the reaction time scale is smaller than the turbulent mixing time scale. This means that the combustion is controlled by turbulent mixing. In the shear layer, where the heat release rate and the scalar dissipation rate have the highest value, the flame is stabilized due to finite rate chemistry with small Damköhler numbers and a high fraction of fine structure. This solver allows three-dimensional gas dynamic simulation of high-speed multicomponent reactive flows relevant to practical combustion applications.

Dislocation is one of the major challenges in unmanned aerial vehicle (UAV) image stitching. In this paper, we propose a new dynamic programming for seamlessly stitching UAV images using optical flow. Our solution consists of two steps: Firstly, an image-matching algorithm is used to correct the images so that they are in the same coordinate system. Secondly, a new dynamic programming algorithm is develop based on the concept of a stereo dual-channel energy accumulation using optical flow. A new energy aggregation and traversal strategy is adopted in our solution, which can find a more optimal seam line for adjacent image stitching. Our algorithm overcomes the theoretical limitation of the classical Duplaquet algorithm. Experiments show that the algorithm can effectively solve the dislocation problem in UAV image stitching. Beyond that, our solution is also direction-independent, which has more adaptability and robustness for UAV images.

We present an exact expression for the upscaled dynamic dispersion coefficient (D) for one-dimensional transport by Hagen-Poiseuille flow which is the basis for modeling transport in porous media idealized as capillary tubes. The theoretical model is validated by comparing the breakthrough curves (BTCs) from a 1D advection-dispersion model with dynamic D to that from direct numerical solutions utilizing a 2D advection-diffusion model. Both Taylor dispersion theory and our new theory are good predictors of D at lower Peclet Number (Pe) regime, but gradually fail to capture most parts of BTCs as Pe increases. However, our model generally predicts the mixing and spreading of solutes better than Taylor’s theory since it covers all transport regimes from molecular diffusion, through anomalous transport, and to Taylor dispersion. The model accurately predicts D based on the early part of BTCs even at relatively high Pe regime (~62) where the Taylor’s theory fails. Furthermore, the model allows for calculation of the time scale that separates Fickian from non-Fickian transport. Therefore, our model can readily be used to calculate dispersion through short tubes of arbitrary radii such as the pore throats in a pore network model.

This paper investigates whether currency risk is priced differently in the different sectors (industrial, financial, and basic materials) of equity markets in a sample of developed United States of America (USA) and developing economies (Brazil, India, Poland, and South Africa). The paper makes use of the following techniques: (i) Univariate Autoregressive Fractionally Integrated Moving Average and Exponential General Autoregressive Conditional Heteroskedastic (ARFIMA-EGARCH), (ii) the Markov-Switching method (MS), and (iii) the Canonical Vine Copulas (C-Vine) techniques. Using a sample of daily data made of the foreign exchange rate against the domestic currency and equity market sectors; our findings show that there is an asymmetry effect between equities markets and the foreign exchange rate: there is a heterogeneous, strong, and positive dependence between the two. Higher equities prices are associated with depreciation of local currencies, according to US dollar (USD) exchange rates. In addition, we find that the selected emerging economies are pricing a positive and considerable currency risk. The pricing of currency risk has a varied effect in both regimes representing the states of the economy. In fact, when currency risk pricing has a beneficial impact on certain sectors of the economy, investors predict better returns.

The present article seeks to analyse the period 1938-1940, when the Romanian interwar democracy was suspended through the promulgation of the anti-liberal Constitution of 27 February 1938. The Constitution abolished the political parties and trade unions, replacing them with new institutions established according to royal decrees: the royal single party, known as the National Renaissance Front (Frontul Renaşterii Naţionale, FRN) and corporations of workers and employers, respectively. Starting from that moment, the regime, through its representatives, made recourse to a nationalist rhetoric directed against the democratic parliamentary system. Moreover, a cult of personality of the monarch can be identified in the speeches of the royal corporatist ‘parliament’, as well as in the doctrine of FRN and the Nation’s Party (its successor), but also in the regime’s youth organisation, ‘The Country’s Sentinel’ (Straja Ţării), whose First Sentinel was the authoritarian monarch himself. Thus, the cult of personality of Carol II represented one of the sources of inspiration for the dictator Nicolae Ceauşescu and for the leaders of this totalitarian regime.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

We investigated the dynamics of a simple master equation describing the evolution of a probability distribution between two states, \( p_1 \) and \( p_2 \) (with \( p_1 + p_2 = 1 \)). Our focus is on the behavior of the entropy \( S \), the distance \( D \) from the uniform distribution (\( p_1 = p_2 = 1/2 \)), and the free energy \( F \). We define two ratios, \( \eta_S = \frac{dS/dt}{dF/dt} \) and \( \eta_D = \frac{dD/dt}{dF/dt} \), and find that both diverge to plus-minus infinity as the system evolves towards the uniform distribution. This divergence marks a critical transition point where the master equation temporarily loses physical meaning. However, after this divergence, the system settles into a new, well-behaved regime where the solutions stabilize at finite values, representing a new equilibrium or steady state. This two-regime behavior underscores the intricate dynamics of simple probabilistic systems as they approach and surpass equilibrium, providing insights into the complex interplay of entropy, distance, and free energy in statistical mechanics.

In chronic myeloid leukemia (CML), a clonal proliferative disorder of granulocytic lineage, the 90%‐95% of cases are characterized by t(9;22) (q34.1;q11.2) translocation, leading to the Philadelphia chromosome (1). Rarely, CML patients directly present a blast crisis, mostly of myeloid origin (2, 3). Herein, we describe one rare CML case, showing an unusual early T lymphoid blastic crisis.

The detection and enrichment of circulating melanoma cells is a challenge as the cells are very heterogeneous in terms of their biomechanical properties and surface markers. In addition, there is a lack of valid and reliable biomarkers that predict progress and therapeutic response. We here analyzed the elasticity of A375 melanoma cells applying force spectroscopy and a microfluidic method. To identify and eventually separate circulating tumor cells, it is crucial to precisely know their physical properties. First, we used standard AFM force spectroscopy, where the elasticity of the cells is calculated from indentation with a pyramidal tip. To extend the limits of measurement with a tip, we then used cantilevers without a tip to press on the cells over a large area. The resulting Young’s moduli are slightly lower and vary less without tip presumably because of the inhomogeneity of the cells. Finally, we implemented our microfluidic method. We measured single cell elasticity by analyzing its deformation in high-speed micrographs while passing a stenosis. Combining the force field and the change in shape provides the basis for a stress strain diagram. The results from microfluidic deformation analysis were in accordance with the results from force spectroscopy. The microfluidic method provides advantages over conventional methods, since it is less invasive and less likely to harm the cell during the measurement, and the whole cell is measured as one entity without contact to a stiff substrate, while force spectroscopy is limited to the contact area of the tip, and in some cases dependent of the cell substrate interaction. Consequently, microfluidic deformation analysis allows to predict the overall elastic behavior of the whole inhomogeneous cell in three-dimensional force fields. This method may contribute to improve the detection of circulation melanoma cells in the clinical practice.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

The continuous casting tundish is non-isothermal due to heat losses and temperature variation from the inlet stream generating relevant convection forces. This condition is commonly avoided through qualitative fluid dynamic analysis only. This work searches to establish the conditions for which non-isothermal simulations are mandatory or for which isothermal simulations are enough to accurately describe the fluid dynamics inside the tundish by quantifying the buoyant and inertial forces. The mathematical model, simulated by CFD software, considers the Navier-Stokes equations, the realizable k- model for solving the turbulence, and the Lagrangian discrete face to track the inclusion trajectories. The results show that temperature does not significantly impact the volume fraction percentages or the mean residence time results, nevertheless, bigger velocity magnitudes under non-isothermal conditions than in isothermal conditions and noticeable changes in the fluid dynamics between isothermal and non-isothermal cases in all the zones where buoyancy force dominates over inertial forces were observed. Because of the results, it is concluded that isothermal simulations can accurately describe the flow behavior in tundishes when the flow control devices control the fluid dynamic, but the simulation without control devices or with a weak fluid dynamic dependence on the control devices requires non-isothermal simulations.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

The International tax regime (ITR) has been transformed after the Great Recession of 2008–2009. The G20/Organization for Economic Cooperation and Development (OECD)’s Base Erosion and Profit Shifting (BEPS) project (2013–2015) has fundamentally changed the ITR, giving new life to the single tax principle (income should be taxed once, i.e., no double taxation and no double non taxation). Reaction to BEPS has varied dramatically between the EU and the US, the two largest markets in the world. In the EU BEPS is taken very seriously, as shown for example by the new Anti-Tax Avoidance Directives that implement the single tax principle. In the US BEPS is almost invisible; while the US model tax treaty has been amended to incorporate it the US has refused to sign the Multilateral Instrument to implement BEPS in its treaties and the only other BEPS action that the US has taken is country by country reporting. It thus appears that the future of BEPS and the ITR depends on whether the EU or the US view prevails, i.e., whether multinationals can be forced to pay significant tax on the 160–240 billion that are currently not taxed annually because of BEPS. While US multinationals as well as EU multinationals are exposed to the EU ATAD and related measures while operating in Europe, they are less subject to EU anti BEPS measures elsewhere in the world. It therefore is crucial to assess the reaction to BEPS in the other large economy that was involved in its development, namely China. This article attempts to assess China’s reaction to BEPS based on Chinese sources. It shows that China takes BEPS seriously. Therefore, given the reactions of China (as well as India, which is even more aggressive than China for example in taxing the digital economy) it seems likely that eventually the EU view of BEPS will prevail and US based multinationals will eventually be forced to pay tax on the over 100 billion they shift offshore each year.

Underwater imaging presents unique challenges, notably color distortions and reduced contrast due to light attenuation and scattering. Most underwater image enhancement methods, first use linear transformations for color compensation and then enhance the image. We observed that linear transformation for color compensation is not suitable for certain images. For such images, a non-linear mapping is a better choice. Our paper introduces a unique underwater image restoration approach leveraging a streamlined convolutional neural network (CNN) for dynamic weight learning for linear and non-linear mapping. In the first phase, a classifier is applied that classifies the input images into Type-I or Type-II. In the second phase, depending on the classification, the Deep Line Model (DLM) for Type-I images or the Deep Curve Model (DCM) for Type-II images. For mapping an input image to an output image, DML creatively combines color compensation and contrast adjustment in a single step and uses deep lines for transformation, whereas DCM employs higher-order curves. Both models utilize lightweight neural networks that learn per-pixel dynamic weights based on the input image’s characteristics. Comprehensive evaluations on benchmark datasets using metrics like peak signal-to-noise ratio(PSNR) and root mean squares error (RMSE) affirm our method’s effectiveness in accurately restoring underwater images, outperforming existing techniques.

The main focus of the in vitro toxicity assessment methods is on the viability of the cells, which is usually based on metabolism changes. Yet, when exposed to toxic substances, the cell triggers multiple signals in response. With this in mind, we have developed a promising cell-based toxicity method that observes various cell responses when exposed to toxic substances (either death, division or remaining viable). Based on the collective cell response, we observed and predicted the dynamics of the cell population to determine the toxicity of the toxicant. The method was tested with two different conformations: In the first conformation, we exposed a monoculture model of blood macrophages to UV light, hydrogen peroxide, nutrient deprivation, tetrabromobisphenol A, fatty acids and 5-fluorouracil. In the second, we exposed a coculture liver model consisting of hepatocytes, hepatic stellate cells, Kupffer cells and liver sinusoidal endothelial cells to rifampicin, ibuprofen and 5-fluorouracil. The method showed good accuracy compared to established toxicity assessment methods. In addition, this approach provided more representative information on the toxic effects of the compounds as it considers the different cellular responses induced by toxic agents.

Wound healing is a multi-factorial response to tissue injury, aiming to restore tissue continuity. Numerous recent experimental and some clinical studies, clearly indicate that probiotics applied topically promote the wound healing process. However, the precise mechanism by which they contribute to healing is not yet clear. Each strain appears to exert a distinctive, even multi-factorial action on different phases of the healing process. Given that a multi-probiotic formula exerts better results than a single strain, the pharmaceutical industry has embarked on a race for the production of a formulation containing a combination of probiotics, capable of playing a role in all the phases of the healing process. Hence, the object of this review is to describe what is known to date of the distinctive mechanisms of each of the most studied probiotic strains in order to further facilitate research towards the development of combinations of strains and doses, covering the whole spectrum of healing. Eleven probiotic species have been analyzed, the only criterion of inclusion being a minimum of two published research articles.

The presence of the quantum Rayleigh scattering, or spontaneous emission, inside a dielectric medium such as a beam splitter or an interferometric filter, prevents a single-photon from propagating in a straight-line. Modelling a beam splitter by means of a unitary transformation is physically meaningless because of the loss of photons. Additional missing elements from the conventional theory are: 1) the quantum Rayleigh stimulated emission which can form groups of photons of the same frequencies, and 2) the unavoidable parametric amplification of single-photons in the original parametric crystal. An interference filter disturbs, through multiple internal reflections, the original stream of single-photons, thereby confirming the existence of groups of photons being spread out to lengthen the coherence time. The approach of modelling individual, single measurements with statistical ensemble probability amplitudes leads to the counterintuitive explanations of the experimental outcomes and should be replaced with pure states describing instantaneous measurements which are afterwards averaged.

One of the solutions of the Einstein equations, called McVittie solution, signifying a black hole embedded by the dynamic spacetime is studied. In the stationary spacetime the Mcvittie metric becomes the Schwarzschild-de Sitter metric (SdS). The geodesic of a freely falling test particle towards the black hole is examined in the SdS spacetime. It is found that unlike Schwarzschild case the potential of such particle becomes maximum at a point where it eventually stops to follow an unstable circular motion and then resumes its motion towards black hole center. It is shown that an observer or system of particles is spaghettified near the black hole singularity in the SdS spacetime. The dynamic of the universe in the framework of McVittie metric, being a generalized time dependent SdS solution, is represented in terms of that point, called stationary or turning point. The motion of the stationary point is studied in various regimes of the expanding universe and the possible outcomes are discussed in brief.

The COVID-19-medical emergency has ended worldwide, yet there is still a need to evaluate the psychological impact of these years of unprecedented changes on students’ life. Methods: This study aims to assess and compare COVID-19-related stressors (Relationships-and-Academic-Life; Isolation; Fear-of-Contagion) and psychophysical symptoms reported by university students in April-2020, April 2021, and April 2022. The predictive role of COVID-19-related stressors on psychophysical symptoms within each time was also tested. Data were collected among 637 university students in April-2020 (n = 197), April-2021 (n = 200), April-2022 (n = 240). Results: In April-2022, perceived Isolation and Fear-of-Contagion decreased from the peak registered in April-2021, but stress related to Relationships-and-Academic-Life remained noteworthy high. A sharp and ongoing increase in psychophysical symptoms was found, with more than 50% of students reporting clinical levels of Sleep-Disorders, Depression, Psychoticism, and Interpersonal-Sensitivity. In April-2022, students still perceiving stress related to Relationships-and-Academic-Life and Isolation were at risk for Anxiety, Somatization, and Sleep-Disorders, while those still perceiving stress related to Fear-of-Contagion were also at risk for Depression, Obsessive-Compulsive, and Psychoticism. Conclusion: Findings emphasized the long-lasting detrimental effects of the COVID-19-related stress. Interventions must pinpoint the complex post-pandemic adjustment process and their effects on university students' psychophysical health.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

This article introduces a new physically based Lyapunov function difinition, which can be used as acoustic energy for finite amplitude pressure oscillations in reacting systems especially in combustion chambers. Reacting flow is seen as an open, non-equilibrium (parameters are distributed unevenly locally) thermodynamic system. This Lyapunov function is defined as the maximum mechanical work, which could be extracted by a heat engine from studied system, if this system would be disconnected from inlet and outlet and from any other surrounding environment, and the engine could transfer to the surrounding environment only mechanical work.

Flow field based methods are becoming increasingly popular for the analysis of interfacial shear rheology data. Such methods take properly into account the subphase drag by solving the Navier-Stokes equations for the bulk phases flows, together with the Boussinesq-Scriven boundary condition at the fluid-fluid interface, and the probe equation of motion. Such methods have been successfully implemented at the double wall-ring (DWR), the magnetic rod (MR), and the bicone interfacial shear rheometers. However, a study of the errors introduced directly by the numerical processing is still lacking. Here we report on a study of the errors introduced exclusively by the numerical procedure corresponding to the bicone geometry at an air-water interface. In our study we directly input a preset the value of the complex interfacial viscosity and we numerically obtain the corresponding flow field and the complex amplitude ratio for the probe motion. Then we use the standard iterative procedure to obtain the calculated complex viscosity value. A detailed comparison of the set and calculated complex viscosity values is made upon changing different parameters such as real and imaginary parts of the complex interfacial viscosity and frequency. The observed discrepancies yield a detailed landscape of the numerically introduced errors.

The present study seeks to assess the Brand Equity in the network of new fashion designers in the Canary Islands. To this end, we have adapted the Brand Equity model to an online context and proposed a set of metrics for four dimensions: estimate, relevance, awareness, and differen-tiation. The multidimensional approach to online Brand Equity was employed to measure the online Brand Equity of 129 fashion designers from the Canary Islands. The study's findings re-vealed that the number of social media profiles significantly impacts brand awareness and dif-ferentiation. Moreover, the digital maturity level influences brand relevance and overall Brand Equity . Our study highlights the practical value of web data-driven metrics for measuring online Brand Equity , which can be utilised for diagnostic, evaluative, or predictive purposes. The study's outcomes have substantial implications for marketers in the fashion industry aimed at improving online Brand Equity

The shallow water equations are widely applied for the simulation of flow routing in rivers and floodplains, as well as for flood inundation mapping. From a mathematical point of view, they are a hyperbolic system of nonlinear partial differential equations, whose numerical integration is sometimes computationally burdensome. For this reason, the interest of many researchers has been focused on the study of simplified forms of the original set of equations, which requires less computational effort. One of the most commonly applied simplifications consists in neglecting the inertial terms, which changes the hyperbolic model to a parabolic one. The effects of such a choice on the outputs of the simulations of flooding events are controversial and an important topic of debate. In the present paper, two numerical models, recently proposed for the solution of the complete and zero-inertia forms of the shallow waters equations, are applied to several unsteady flow routing scenarios. We simulate synthetic and laboratory studies, starting from very simple geometries and moving towards complex topographies. Analyzing the role of the terms in the momentum equations, we try to understand the effect, on the computed results, of neglecting the inertial terms in the zero-inertia formulation. We analyze the computational costs.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The Huaniushan lead-zinc-silver deposit is a hydrothermal sedimentary exhalative deposit (SEDEX). The mining area has complex geological conditions. The main tectonic structure in the area is the Huaheitan-Shuangfengshan Fault (F3), which controls the distribution of strata and magmatic rocks. Since the discovery of the Huaniushan Lead-zinc-silver polymetallic deposit, there are diverse understandings of the deposit's genesis and mineralization law, making it challenging to meet the geological interpretation requirements of the Huaniushan Lead-zinc-silver polymetallic deposit. Moreover, a single geophysical exploration method utilizes limited rock physical parameters, making it difficult to effectively characterize underground structures. The integrated exploration of multiple geophysical methods can effectively integrate the geophysical characteristics of different rock physical parameters, reducing the multiplicity and uncertainty of geophysical data inverse interpretation. The comprehensive interpretation of three-dimensional inversion based on various geophysical data, the construction of geological-geophysical models based on geological grounds, the establishment of hidden ore exploration and positioning, and the rapid evaluation of geophysical technology systems are the current development trends in mineral exploration. In light of this, this paper conducts research on the three-dimensional inversion interpretation of the heavy magnetoelectric exploration data of the Huaniushan sedimentary exhalative deposit lead-zinc-silver polymetallic deposit in the mining area and constructs a three-dimensional geological-geophysical model of the study area based on the obtained three-dimensional physical structure of the underground three-dimensional density, magnetization intensity, resistivity, and polarizability structure of the study area, in combination with the information of related geology and drilling holes. It comprehensively interprets the favorable mineralization parts in the study area.

Drought is one natural disaster with the greatest impact worldwide. Southern Africa (SA) is susceptible and vulnerable to drought due to its type of climate. In the last four decades, droughts have occurred more frequently, with increasing intensity and impacts on ecosystems, agriculture and health. The work consisted of a systematic literature review on the drought regime’s characteristics in the SA, under current and future climatic conditions, conducted on the Web of Science and Scopus platforms, using the PRISMA2020 methodology, with usual and appropriate inclusion and exclusion criteria to minimize/eliminate the risk of bias, which lead to 41 documents published after the year 2000. The number of publications on the drought regime in SA is still very small. The country with the most drought situations studied is South Africa and the fewer studies are Angola and Namibia. The analysis revealed that the main driver of drought in SA is the ocean-atmosphere interactions including the El Niño Southern Oscillation. The documents used drought indices, evaluating drought descriptors for some regions, but it was not possible to identify one publication that reports the complete study of the drought regime, including the spatial and temporal distribution of all drought descriptors in SA.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

Toll plaza optimization is essential for improving traffic flow and easing congestion on road networks. This study aims to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer facilitation. Different resources are used for data collection, like the National Highway Authority of Pakistan. Physical data is collected from the established Toll Plaza of Peshawar, along with the development of each line. The goal of this study is to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer happiness. The analysis of present traffic patterns, the detection of bottlenecks, and the creation of plans to ease congestion and enhance overall traffic flow are all part of the optimization process. The approaches used in this study include data analysis, simulation, and traffic modeling. PTV VISSIM is software for transportation planning, design, and analysis. The simulations consider various conditions, such as variable traffic volumes, toll collection methods, and lane configurations. When comparing the different optimization strategies, performance indicators like trip time, latency, and queue length are utilized to determine which approach is practical. Waiting time Vs. Existing each lane, etc, is explained. In the end, comparing queue lengths and throughput across different lane scenarios shows that maximizing throughput with existing lanes yields up to 45% improvement with E-tag lanes, 40% with existing E-tag lanes, 38% with E-tag plus additional toll and cash lanes, 32% with three cash lanes, and 28% with two E-tag lanes. Failure to regularly monitor and adjust the existing lane pattern scenario based on traffic patterns can lead to queues being 20% longer. Without proactive evaluation and optimization, there is a potential 63% opportunity for queue length improvement

Backscatter communication, which transmits information by passively reflecting radio frequency (RF) signals, has become a focal point of interest due to its potential to significantly enhance the energy efficiency of Wireless Power Mobile Edge Computing (WPMEC) networks and extend the operational lifespan of terminal devices. However, there is little research on the integration of user cooperation in WPMEC scenarios within volatile network environments. In this paper, we propose a dynamic task offloading scheme for a Backscatter-assisted WPMEC system, which involves two mobile devices (MDs) and a Hybrid Access Point (HAP) with user cooperation. We formulate the energy efficiency (EE) maximization problem as a stochastic programming problem, considering the randomness of task arrivals and time-varying wireless channels. By leveraging Dinkelbach’s method and stochastic network optimization technique, we transform the problem into a series of deterministic sub-problems for each time slot, and convert the non-convex sub-problem into convex ones. We propose a low-complex EE maximization algorithm to solve the convex problems efficiently. Extensive simulations are conducted to validate the performance of our algorithm under various system parameter settings. Experiment results demonstrate that our algorithm not only outperforms the benchmark algorithms by approximately 23%, but also stabilize all queues within the MEC system.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

While some research supports utilizing plain radiography for measuring biomechanical alignment of the spine for prognosis and treatment, there are contrasting viewpoints regarding both the value and utilization of these procedures in conservative care. Evaluation of both conservative and non-conservative approaches to spinal care revealed vast differences in radiographic utilization and interpretation between orthopedic surgeons, primary care physicians, chiropractic physicians, and physical therapists, which may account for the different viewpoints and rationale in the literature. A research summary is provided regarding the various methods of spinal analysis utilized by these professions to help determine if there is any unique diagnostic or prognostic value associated with radiographic utilization that could assist in advancing conservative spinal assessment and treatment. Understanding any unique value provided through biomechanical assessment utilizing plain radiography of the spine established in the literature may help chiropractic physicians determine the appropriate use of radiographic procedures in clinical practice and how to coordinate efforts with other conservative and non-conservative professions to improve spinal healthcare.

The majority of existing numerical simulations of the effect of bridge piers on water movement are based on a limited number of bridge piers at a laboratory scale. Furthermore, some 2D numerical simulations for actual bridge projects have deficiencies, including the use of overly large mesh sizes and an inadequate treatment of bridge piers. In this study, we compare three methods of structural mesh encryption, suspension mesh, and nonstructural mesh based on Delft3D, and apply the optimization scheme to a real bridge project. It is demonstrated that optimal results can be achieved by utilising a grid size comparable to the pier diameter (Dp) in the region away from the piers. In the vicinity of the piers, the grid cell size should be no larger than 1/9 Dp. The suspended grid technique (DD Boundary) can yield results consistent with those obtained using a full-area high-resolution grid, provided that the total number of grids can be reduced and the computational time is considerably reduced. In this study, the unstructured mesh (Deflt3D Flexible Mesh) scheme was unable to capture the oscillations of the wake flow behind the bridge piers. However, the application of the optimized scheme in bridge engineering has demonstrated its practical value. The findings of this study on mesh resolution and suspension mesh scheme can be applied to the Delft3D software and are also useful for other numerical simulation work.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

The Brahmaputra is one of the largest rivers in the world, ranking fifth in average discharge. As a result, it is heavily braided with various intricate paths in order to dissipate its huge energy. Although this river is normally classed as a braided river, it has recently been classified as an anastomosing river due to its multi-channel features over alluvial plains. Additionally, the Brahmaputra river’s morphology is random in nature as a result of its high flow variability and bank erodibility. Its anastomosing planform changes in response to seasonal water and sediment waves, resulting in a morphology that is extremely complex. The purpose of this study is to examine the Brahmaputra river’s anastomosing planform entropy as a measure of complexity, power spectral density as a measure of fluctuation and their relationship to the energy expenditure as an imprint of flflow rate of river systems on alluvial landscapes.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

This paper explores the Wilsonian renormalization group of probe-D-branes, focusing on the Dirac-Born-Infeld (DBI) action. The analysis involves deriving the constant of motion and formulating the Wilsonian renormalization group equation. The study extends to the infrared regime, considering both zero and non-zero temperatures. Additionally, thermodynamic aspects related to the functional form of the grand potential are discussed. The investigation provides insights into the renormalization of probe-D-branes and their thermodynamic properties.

High-flow oscillatory ventilation (HFOV) is a common rescue treatment in infants and children with respiratory failure. This type of ventilation is an effective technique in numerous diseases that affect a child in the postnatal period, such as ARDS, meconium aspiration syndrome (MIS), postnatal pulmonary bleeding and idiopathic pulmonary hypertension (IPH). Although this ventilation technique is commonly recognized as a valuable therapeutic option in the general pediatric population, this is not the same for children with congenital cardiovascular diseases. The key mechanism of oscillatory ventilation is continuous positive pressure administered within the airways via a small tidal volume at high frequency. Tidal volumes are between 1 and 3 ml/kg delivered at 5 – 15 Hz equivalent to 300 – 900 breaths per minute. Few older studies conducted on humans and animals highlight that HFOV may be dangerous for congenital heart patients. According to these evidences, hemodynamic parameters such as blood pressure, wedge pressure, central venous pressure, heart rate and inotrope level can be dangerously changed for patients with congenital heart disease, therefore oscillatory ventilation should be avoided. Numerous retrospective studies have pointed out how oscillatory ventilation constitutes a valid therapeutic option in children with congenital heart disease. Recently, new evidences have highlighted how hemodynamic parameters are modified in a non-significant way by this type of ventilation, remaining beneficial as in the normal pediatric population. This narrative review aims to describe the mechanisms of oscillatory ventilation and collect all the available evidences to support its use in pediatric patients with congenital heart problems.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

The origin of the nucleus remains a great mystery in life science, although nearly two centuries have passed since the discovery of nuclei. To date, studies of eukaryogenesis have focused largely on micro-evolutionary explanations. Here, we examined macro-patterns of C-values (the total amount of DNA within the haploid chromosome set of an organism) for over 110,000 species and the chromosome numbers for over 11,000 species and their potential links with the state of atmospheric oxidation over geological time. Eukaryogenesis was in sync with an over 2.5 order-of-magnitude increase in genome size from prokaryote to eukaryote, and also with a rapid rise of atmospheric oxidation, suggesting that eukaryogenesis would have resulted from a regime shift of genomes driven by the oxidation-driven complexification and structuralization (e.g. chromatin packing).

Fractional flow reserve (FFR) is regarded as the gold standard for assessing the functional significance of coronary artery lesions, yet it remains underutilized in clinical practice. Our objective was to investigate whether FFR results have the potential to alter treatment decisions for coronary lesions compared to visual assessments of angiographic images made by three operators at a high-volume interventional center. In this retrospective study, we aimed to reassess the angiographic images of 63 patients presenting with chronic coronary syndrome (n=39, 61.9%) and acute coronary syndrome (n=24, 38.1%) who underwent FFR. Three experienced interventional cardiologists (with >300 PCI procedures per year) reevaluated, blinded to FFR results, 105 ambiguous lesions in 63 patients to determine angiographic significance and treatment strategy. The observers reached a concordant agreement (≥2 operators made the same decision) to perform PCI in 60 (57.1%) of the lesions based on angiographic evaluation. Interestingly, 9 (15%) of these lesions were functionally non-significant (FFR >0.80). The observers agreed to defer PCI in 45 (42.9%) of the lesions; however, 4 (8.9%) of these were functionally significant (FFR ≤0.80) and required PCI. Thus, inter-observer concordance in visual-guided therapeutic decision-making is variable and not always confirmed by the functional significance of coronary lesions.

The maritime industry contributes to over 80% of global trade and ranks as the sixth-largest emitter of greenhouse gases. The International Maritime Organization has taken strides to reduce these emissions, while the European Union spearheads efforts to establish sustainable maritime transport. However, meeting decarbonisation targets poses significant challenges, with the potential implications of adopting an EU Emission Trading System (ETS) on shipping allowances, particularly at specific borders. If not managed effectively, this could result in diversifying regular container shipping routes away from EU ports, potentially leading to increased shipping emissions and disrupting the logistics trade and security chain. These challenges are exacerbated by the International Maritime Organization's lack of a carbon fee on bunkering, which creates an imbalance. The ETS Directive has fostered unfair competition between EU and non-EU ports due to discrepancies in applying emission unit allowances. It is imperative to implement preventive measures to contain and prevent the shift of operations from EU ports to nearby ports, ensure equitable treatment of EU transhipment ports and their competitors, and thwart carbon leakage. Additionally, the recent Houthis attacks on the Red Sea have significantly impacted shipping costs on the Cape of Good Hope route to Europe, necessitating increased allowances to and from Europe.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

The maritime industry contributes to over 80% of global trade and ranks as the sixth-largest emitter of greenhouse gases. The International Maritime Organization has taken strides to reduce these emissions, while the European Union spearheads efforts to establish sustainable maritime transport. However, meeting decarbonisation targets poses significant challenges, with the potential implications of adopting an EU Emission Trading System (ETS) on shipping allowances, particularly at specific borders. If not managed effectively, this could result in diversifying regular container shipping routes away from EU ports, potentially leading to increased shipping emissions and disrupting the logistics trade and security chain. These challenges are exacerbated by the International Maritime Organization's lack of a carbon fee on bunkering, which creates an imbalance. The ETS Directive has fostered unfair competition between EU and non-EU ports due to discrepancies in applying emission unit allowances. It is imperative to implement preventive measures to contain and prevent the shift of operations from EU ports to nearby ports, ensure equitable treatment of EU transhipment ports and their competitors, and thwart carbon leakage. Additionally, the recent Houthis attacks on the Red Sea have significantly impacted shipping costs on the Cape of Good Hope route to Europe, necessitating increased allowances to and from Europe.

Radio-dynamic therapy (RDT), as an emerging cancer treatment method, has attracted attention due to its remarkable therapeutic efficacy using low-dose, high-energy radiation (such as X-rays), and has shown significant potential in cancer treatment. The RDT system typically consists of scintillators and photosensitizers. Scintillators absorb X-rays and convert them to visible light, activating nearby photosensitizers to generate cytotoxic reactive oxygen species (ROS). Challenges faced by the two-component strategy, including low loading capacity and inefficient energy transfer, hinder its final effectiveness. In addition, the tumor microenvironment (TME) with hypoxia and immunosuppression limits the efficacy of RDTs. Recent advances introduce one-component RDT systems based on nanomaterials with high-Z metal elements, which effectively inhibit deep-seated tumors. These novel RDT systems exhibit immune enhancement and immune memory, potentially eliminating both primary and metastatic tumors. This review comprehensively analyzes recent advances in the rational construction of RDTs, exploring their mechanisms and its application in the treatment of deep-seated tumors. Aimed at providing a practical resource for oncology researchers and practitioners, the review offers new perspectives for potential future directions in RDT research.

This paper presents an analysis of the power flow within the Northern Interconnected Grid of Cameroon. The Newton-Raphson method has been performed, known for its accuracy, under MATLAB software, to model and solve complex power flow equations. This study simulates a series of outage scenarios to evaluate the responsive-ness of the grid. The results obtained underline the crucial importance of reactive power management and highlight the urgent need to consolidate the grid infrastructure of North Cameroon. To increase grid resilience and stability, the paper recommends the strategic integration of renewables and the development of interconnections with other power grids. These measures are presented as viable solutions to meet cur-rent and future energy distribution challenges, ensuring a reliable and sustainable power supply for Cameroon.

Mobile Edge Computing (MEC) integrated with Wireless Power Transfer (WPT) is emerging as a promising solution to reduce task delays and extend the battery life of Mobile Devices (MDs). Cooperative user communication, or relay technology, enhances communication efficiency for users located far from the base station by mitigating the double near-far effect caused by distance. This is considered a key technology in Beyond 5G (B5G) and future communication systems. In this paper, we focus on maximizing the long-term energy efficiency (EE) of a user-cooperation WPT-MEC system, while taking into account the uncertain load dynamics at the edge MD and the time-varying state of the wireless channel. The joint optimization of wireless charging time fraction, MD offloading duration, helper node processing time, and transfer power decision presents significant challenges due to the coupling of data offloading among cooperative users and a volatile system environment. To address these challenges, we formulate the problem as a stochastic programming problem and propose an online control algorithm, DOUCA, to solve it. Our approach utilizes Dinkelbach’s method and Lyapunov optimization theory to decouple the sequential decision problem into a deterministic sub-problem for each time slot. For the sub-problem, we use variable substitution to convert the non-convex problem into a convex one, containing only a small number of variables, which can be efficiently solved. Furthermore, we provide a mathematical analysis of our algorithm’s performance. Extensive simulation results demonstrate the effectiveness of our proposed algorithm, as evidenced by an impressive energy efficiency improvement of over 20% compared to benchmark methods. Our algorithm also achieves a trade-off between EE and system stability.

It is imperative to conduct experimental studies on the seepage behavior of gas-bearing coal under cyclic dynamic loading conditions. This paper focuses on the evolution of coal permeability under the combined effects of dynamic loading, static loading, and gas adsorption. The principal conclusions are as follows. (1) As the frequency and amplitude of dynamic loading increase, the development of pore and fissure structures within the coal body becomes increasingly pronounced during dynamic loading cycles, resulting in a gradual rise in permeability. Notably, as the coal approaches its yielding stage, the permeability can increase by up to 47%. (2) The permeability curve is divided into four regions: the compaction reduction zone, the oscillation zone, the gradual recovery zone, and the abrupt increase zone of failure. Ultimately, in the failure phase, the permeability surges dramatically, potentially reaching 4 to 5 times the initial permeability. (3) When the static load stage is constant, the rate of change in permeability of the coal under dynamic loading decreases with increasing adsorption amount. When the adsorption amount is constant, the rate of change in permeability of the coal under dynamic loading increases with the increase in static load stress stage, with the maximum increase reaching 75.2%. It can be concluded from the rate of change in permeability and the dynamic loading sensitivity coefficient that the permeability of the coal is highly sensitive to cyclic dynamic loading, with increased sensitivity associated with larger static load stages and decreased sensitivity with greater adsorption amounts.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

The advancement of autonomous capabilities in maritime navigation has gained significant attention, with a trajectory moving from decision support systems to full autonomy. This push towards autonomy has led to extensive research focusing on collision avoidance, a critical aspect of safe navigation. Among the various possible approaches, Dynamic Programming is a promising tool for optimizing collision avoidance maneuvers. This paper presents a DP formulation for collision avoidance of autonomous vessels. We set up the problem framework, formulate it as a multi-stage decision process, define cost functions and constraints focusing on the actual requirements a marine maneuver must comply with, and propose a solution algorithm leveraging parallel computing. Additionally, we present a greedy approximation to reduce algorithm complexity. Through case studies, we demonstrate the effectiveness of the proposed approach in navigating complex scenarios, contributing to the future of autonomous maritime navigation. Through case studies, we show the efficacy of our approach in navigating complex scenarios.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

Feature selection is predominantly used in machine learning tasks, such as classification and regression. It selects a subset of features (relevant attributes of data points) from a larger set that contributes as optimally as possible to the informativeness of the model. There are exponentially many subsets of a given set, and thus, the exhaustive search is only practical for problems with at most a few dozen features. In the past, there have been attempts to reduce the search space using dynamic programming. However, models that consider similarity in pairs of features besides the quality of individual features do not provide the required optimal substructure. As a result, algorithms, which we will call suboptimal dynamic programming algorithms, find a solution that may deviate significantly from the optimal one. In this paper, we propose a dynamic programming algorithm with an iterative upgrade where the order of feature processing is inverted in each iteration. Such an alternating approach allows for improving the optimization function by using the score from the previous iteration to estimate the contribution of unprocessed features. The iterative process is proven to converge and terminate when the solution does not change in three successive iterations or when the number of iterations reaches the threshold. Results in more than 90 % of tests align with those of the exhaustive search, being competitive and often superior to the reference greedy approach. The validation was done by comparing the scores of output feature subsets and examining the accuracy of different classifiers learned on these features. In the context of feature selection, the proposed algorithm can be characterized as a filter method. However, we expect that the idea of alternating suboptimal optimization will soon be generalized to tasks beyond feature selection.

Spacecraft recovery technology is crucial in the field of aerospace, in which the parachute plays a key role in slowing down the descent speed of the spacecraft and realizing a smooth landing. In order to construct a dynamically adjustable parachute deployment strategy, it is necessary to measure the parachute dynamic load accurately in real time. However, the existing sensor measurement scheme is difficult to meet the measurement requirements due to its large structure and complex wiring. In order to meet the current demand for real-time measurement of parachute cords dynamic load, a miniature measuring instrument is designed.According to the function and technical requirements of the miniature measuring instrument, the hardware modules of the acquisition system are selected and designed, and the integration debugging and performance optimization of the microcontroller module, A/D sampling module, signal acquisition circuit and power supply module are carried out. The software of the parachute cords tension acquisition system based on the miniature measuring instrument is developed. The elastomer is modeled by using SolidWorks and statically analyzed by using AnsysWorkbench finite element analysis software. Then the final structure of the elastomer and the pasting position of the strain gage are determined through the results analysis as well as experimental verification. The hardware module of the signal acquisition system for the miniature measuring instrument is then encapsulated. The force value of the miniature measuring instrument is calibrated and tested many times by using the microcomputer-controlled electronic universal testing machine. The experimental results show that the designed miniature measuring instrument has accurate data, strong stability and good real-time performance, which meets the demand for real-time accurate measurement of miniature measuring instrument, and can provide reliable data for parachute cords parameter validation and stepless unfolding design.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

Drag reduction by laminarization, an innovative technology in aerodynamics design, provides the possibility to improve significantly the aerodynamic performance of aircraft and remains to be one of the most promising and effective technologies. In this paper, the design method for transonic natural laminar flow (NLF) wing at high Reynolds number is investigated in details and a new optimization model is established to solve conflicts between the increase of a laminar flow region and the shock wave strength at the trailing edge. In order to numerically handle this competitive situation efficiently, a two-objective hierarchical variable fidelity Pareto evolutionary optimization model based on search space contraction is proposed and implemented. Numerical experiments show that it can capture simultaneously a Pareto front of the two-objectives: a wave drag minimization and a laminar flow region maximization. The results also show that both wave drag and skin friction drag performances of non-dominated Pareto members can be significantly improved via the optimal laminar wing shape and shock wave control device. Nearly 40% of the laminar flow area on the wing surface is achieved at the Reynolds number of 107. It is concluded that the present hierarchical variable-fidelity multi-objective evolutionary optimization method is computationally efficient, and illustrate its potential for solving complex engineering design problems.

Refractory materials are used worldwide in process equipment. However, gaseous and liquid process products penetrate the surface layer, and deep into the volume of refractories destructing rather expensive constructions complicated to repair. To address this challenge, there is a need to develop protective coatings for refractory that can limit the penetration of working media and extend their operational lifespan. In this work, the application of gas-dynamic cold spraying (CGDS) to produce a coating on the refractory using fine titanium dioxide (TiO2) particles is explored. These particles are accelerated within a nitrogen flow, passing through a Laval nozzle, and then sprayed onto a fireclay surface. The mechanisms of particle deposition and layer formation on porous surfaces through experiments and numerical simulations were investigated. The geometry of a typical refractory pore was determined, which was then incorporated into Computational Fluid Dynamics (CFD) simulations to model the cold spraying process of porous substrates. As a result, the influence of the particle size on its velocity and angle of penetration into pores was established. Experimental findings demonstrate the effective closure of pores and the formation of a particle layer on the refractory surface. Furthermore, the nanoindentation tests for the refractory samples showcase capabilities for checking coating thickness for porous materials.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This paper presents a dynamic homotopy technique that can be used to calculate a preliminary result for a power flow problem (PFP). This result can then be used as an initial estimate to efficiently solve the PFP using either the classical Newton-Raphson (NR) method or its fast decoupled version (FDXB) while still maintaining high accuracy. The preliminary stage for the dynamic homotopy problem is formulated and solved by employing integration techniques, where implicit and explicit schemes are studied. The dynamic problem assumes an initial condition that coincides with the initial estimate for a traditional iterative method such as NR. In this sense, the initial guess for the FPF is adequately set as a flat start, which is a starting for the case when this initialization is of difficult assignment for convergence. The static homotopy method requires a complete solution of a PFP per homotopy pathway point, while the dynamic homotopy is based on numerical integration methods. This approach can require only one LU factorization at each point of the pathway. Allocating these points properly helps avoid several PFP resolutions to build the pathway. The hybrid technique was evaluated for large-scale systems with poor conditioning, such as a 109272-bus model and other test systems under stressed conditions. A scheme based on the implicit backward Euler scheme demonstrated the best performance among other numerical solvers studied. It provided reliable partial results for the dynamic homotopy problem, which proved to be suitable for achieving fast and highly accurate solutions using both the NR and FDXB solvers.

Treatment with herbal medicine continues to enjoy widespread popularity not only in the developing world, because of low costs, easy availability, and low risk of adverse effects. One such plant is Curcumin longa L., or turmeric, which has a long history of both culinary and medicinal uses throughout Asia, spanning thousands of years. In addition to traditionally being used as a dye, as a flavouring and colouring agent in foods, and, e.g., marriage rituals, turmeric is also notable for its long history of use to treat a variety of medical conditions, including inflammatory, bacterial, and fungal diseases and infections, jaundice, tumours, and ulcers among others. In light of this long history of use, it is not surprising to find that also modern biochemistry and clinical research studies show that a significant component of turmeric, curcumin, may have a multitude of therapeutic benefits, much of it attributed to the herb’s antioxidant qualities which are crucial for the prevention and treatment of, e.g., chronic inflammatory illnesses, conditions that often act as precursors for other serious diseases, including cancer and neurological disorders, such as Parkinsons and Alzheimer’s. Furthermore, investigations on the safety profile and toxicity of curcumin have shown that it is generally safe even at large dosages, although caution is necessary as curcumin also have documented anticoagulant effects. This article is focused on providing a better perspective into molecular mechanisms for possible actions along with an in-depth review of recent studies of curcumin, its beneficial role and therapeutic applications in chronic health conditions, with a focus on its cancer, inflammatory bowel disease, osteoarthritis, atherosclerosis, peptic ulcer, Covid19, psoriasis, vitiligo, and depression.

In nature and engineering applications, flexible fiber beds covering biological surfaces can play a role in reducing resistance. These fibers deform under the action of fluids, and this deformation affects the fluid flow state, forming a complex fluid-solid interaction phenomenon. To quantitatively analyze such issues, the physical model is simplified to the deformation problem of an soft hair bed caused by Stokes flow, and the deformation problem of a single fiber caused by Stokes flow is further studied. The deformation problem of an elastic single fiber in a channel caused by Stokes flow can be described by a nonlinear integral equation. We have obtained a new series solution, which has been compared with the previous perturbation method to verify the accuracy and effectiveness of the series solution. Meanwhile, we have further provided an extended form of flexible fiber deformation through experimental fitting. This fluid-solid interaction problem involves multiple fields and is very important in many natural and engineering systems. The research in this paper can not only help us better understand complex phenomena in nature but also delve into the interaction mechanism between fluids and solids, providing a theoretical basis for future scientific research and engineering applications.

Autonomous navigation in dynamic environments poses a significant challenge in the field of ro-botics with the primary goals of ensuring both smooth and safe movement. This study introduces control strategy based on an Adaptive Neuro-Fuzzy Inference System (ANFIS) to enhance au-tonomous robot navigation in dynamic environments, emphasizing on collision-free path plan-ning. This strategy employs, a path planning technique to develop a trajectory that allows the ro-bot to navigate smoothly while avoiding collisions with both static and dynamic obstacles. The developed control system incorporates four ANFIS controllers: two are tasked with guiding the robot toward its end point, and the other two are activated for obstacle avoidance. The experi-mental setup conducted in CoppeliaSim involves a mobile robot equipped with ultrasonic sensors navigating in an environment with static and dynamic obstacles. Simulation experiments are conducted to demonstrate the model's capability in ensuring collision-free navigation, employing a path planning algorithm to ascertain the shortest route to the target destination. The simulation results highlight the superiority of the ANFIS-based approach over conventional methods, partic-ularly in terms of computational efficiency and navigational smoothness.

As well known, the torque produced by a rotating motor generates an opposite and equal reaction torque in the machine casing that must be transmitted to the base. In many applications, especially when the reaction moment has high values, it is necessary to apply some constructive solutions, which in certain cases are difficult to implement. In this context, the need to reduce the reaction moment from drive motors is a challenging topic, which has not been completely exhausted. In this paper, the authors present an original concept of a device which uses the centrifugal force generated by some equidistantly placed weights on a chain drive, for reducing the reaction torque of the motor used for driving a rotating tool. The proposed system is capable to produce a supplementary torque which can be added to driving moment. Due to this fact, by using this system, the power of the driving motor can be decreased, with the consequence of reducing the reaction moment, that must be absorbed by the base.

This manuscript presents a new two-parameter unit stochastic distribution, obtained by transforming the Laplace distribution, using generalized logistic map, into a unit interval. The distribution thus obtained is named the Laplace-logistic unit (abbreviated LLU) distribution, and its basic stochastic properties are examined in detail. Also, the procedure for estimating parameters based on quantiles is provided, along with the asymptotic properties of the obtained estimates and the appropriate numerical simulation study. Finally, the application of the LLU distribution in dynamic and regression analysis of real-world data with accentuated "peaks" and "fat" tails is also discussed.

Over the past decade and a half, dynamic functional imaging has revolutionized the neuroimaging field. Since 2009, it has revealed low dimensional brain connectivity measures, has identified potential common human spatial connectivity states, has tracked the transition patterns of these states, and has demonstrated meaningful alterations in these transition and spatial patterns in neurological disorders, psychiatric disorders, and over the course of development. Recently, researchers have begun to analyze this data from the perspective of dynamic system and information theory in the hopes of understanding how these dynamics support less easily quantified processes, such as information processing, cortical hierarchy, and consciousness. Consciousness, in particular, appears to be strongly linked to entropy production in the brain. Little attention has been paid to the effects of psychiatric disease on entropy production in the human brain, however. Even disorders characterized by substantial changes in conscious experience have not been widely analyzed from this perspective. We begin to rectify this by examining the complexity of subject trajectories in state space through the lens of information theory. Specifically, we identify a basis for the dynamic functional connectivity state space and track subject trajectories through this space over the course of the scan. The dynamic complexity of these trajectories is assessed along each dimension of the proposed basis space. Using these estimates, we demonstrate that schizophrenia patients display substantially simpler trajectories than demographically matched healthy controls, and that this drop in complexity concentrates along specific dimensions. We also demonstrate that entropy generation in at least one of these dimensions is linked to cognitive performance. Overall, results suggest great value in applying dynamic systems theory to problems of neuroimaging and reveal a substantial drop in the complexity of schizophrenia patients’ brain function.

A thermal system in very deep Lake Tazawa (maximum depth, 423 m) was investigated by estimating the heat budget. In the heat budget estimate, the net heat input at lake surface and the heat input by river inflow and groundwater inflow were considered. Then, the heat loss by snowfall onto lake surface was taken into account. Meanwhile, lake water temperature was monitored at 0.2 m to the bottom by mooring temperature loggers for more than two years. The heat storage change of the lake from the loggers was calibrated by frequent vertical measurements of water temperature at every 0.1 m pitch by a profiler with high accuracy (± 0.01 °C). The heat storage change (W/m2) obtained by the temperature loggers reasonably accords to that from the heat budget estimate. In the heat budget, the net heat input at lake surface dominates the heat storage change, but the significant heat loss by river inflow sporadically occurred, which is caused by the relatively large discharge from a reservoir in the upper region. How deep the vertical water circulation in the lake occurs in winter was judged by the differences between water temperatures at 0.2 m depth and bottom and between vertical profiles of dissolved oxygen over winter. It is strongly suggested that the whole water circulation does not occur every winter, if any, very weak.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Due to the rapid development of unmanned aerial vehicles (UAVs) communication technology, UAVs are gradually competing with primary users (PUs) for spectrum resources. Cognitive radio (CR) is a promising solution to meet the needs. Cooperative spectrum sensing (CSS) is considered as an effective method to detect the PU signal and identify available spectrum resources for UAVs in a cognitive UAV network (CUAVN). However, the cooperative mode among multiple UAVs may incur a high overhead, resulting in performance degradation. Therefore, we introduce a differential sequential 1 (DS1), which incorporates a differential mechanism and leverages the sequential idea based on the classical voting rule to enhance cooperative performance and efficiency. In view of this, we formulate three scenarios to characterize the PU activity and introduce a multi-slot cooperative mode within a single UAV to realize cooperative gain. Further, only the information change about the PU status is sequentially calculated in DS1, and combined with a sequential idea, the efficiency of the voting rule is greatly improved. Moreover, the application of support vector machines (SVM) in dynamic selection enables the selection of the most suitable voting rule based on diverse sensing parameters. This dynamic selection process ensures optimal performance and efficiency by adapting the voting rule to the specific characteristics of the given scenario. Finally, simulation results demonstrate that the superiority of our proposal with respect to the detection performance, sample size and the energy efficiency is evident, which proves the high performance of the proposed policy.

In this work, we explore the ability to dynamically group the Wind Turbine (WT) of a Wind Farm (WF) based on the behaviour of some of their Supervisory Control And Data Acquisition (SCADA) signals to detect the turbines that exhibit abnormal behaviour. We centre this study on a small WF of five WTs. We use the fact that the same signals from different turbines in the same WF coherently evolve temporally in a time domain, describing very similar waveforms. In this contribution, we use averaged signals from the SCADA system and omit maximums, minimums and standard deviations, focusing mainly on velocities and other slowly varying signals. For the temporal analysis, sliding windows of different temporal durations and overlapings are explored. The capability to automatically identify WTs whose signals differ from the group’s behaviour can alert and program preventive maintenance operations on such WTs before a major breakdown occurs.

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

The extensive use of polypropylene (PP) in various industries has heightened interest in devel-oping efficient methods for recycling and optimising its mixtures. This study focuses on formu-lating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The in-vestigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, at-taining R² values over 0.99. Symbolic regression further enhanced these models, offering signif-icant improvements. To mitigate overfitting, empirical noise and variable swapping were in-troduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the de-velopment of recycling technologies and sustainable practices in the polymer industry by opti-mising processing and enhancing the use of recycled materials.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Ombrian curves, i.e. curves linking rainfall intensity to return period and time-scale, are well-established engineering tools, crucial to the design against storm waters and floods. Whereas at-site construction of such curves is considered a standard hydrological task, it is a rather challenging one when large regions are of interest. Regional modelling of ombrian curves is particularly complex due to the need to account for spatial dependence together with the increased variability of rainfall extremes in space. We develop a framework for the parsimonious modelling of the extreme rainfall properties at any point in a given area. This is achieved by assuming a common ombrian model structure except for a spatially varying scale parameter which is itself modelled by a spatial smoothing model for the 24 h average rainfall maxima that employs elevation as an additional explanatory variable. The fitting is performed on the pooled all-stations data using an advanced estimation procedure (K-moments) that allows both for reliable high-order moment estimation and simultaneous handling of space-dependence bias. The methodology is applied in the Thessaly region, a 13 700 km2 water district of Greece characterized by varying topography and hydrometeorological properties.

In this contribution, we present a high-speed multiplex grating spectrometer based on a spectral coding approach that is founded on principles of compressive sensing. The spectrometer employs a single-pixel InGaAs detector to measure the signals encoded by an amplitude spatial light modulator (digital micromirror device, DMD). This approach leads to a speed advantage and multiplex sensitivity advantage atypical for standard dispersive systems. Exploiting the 18.2 kHz pattern rate of the DMD, we demonstrate 4.2 ms acquisition times for full spectra with a bandwidth of 450 nm (5250 cm-1 – 4300 cm-1; 1.9 µm – 2.33 µm). Due to the programmability of the DMD, spectral regions of interest can be chosen freely, thus reducing acquisition times further, down to the sub-millisecond regime. The adjustable resolving power of the system accessed by means of computer simulations is discussed, quantified for different measurement modes, and verified by comparison with a state-of-the-art Fourier-transform infrared spectrometer. We show measurements of characteristic polymer absorption bands in different operation regimes of the spectrometer. The theoretical multiplex advantage of 8 was experimentally verified by comparison of the noise behavior of the spectral coding approach and a standard line-scan approach.

Fruits play an important role in human diet and to maintain better health. Globally, India ranks second in fruits production after China. Grapes, mangoes, bananas and oranges were the selected fruit crops for study purpose. The study period is from 1990 to 2018. The present study analyzed the growth rates, instability and elasticity of export quantity, prices of selected fruit crops from major producing countries in the world and also dealt with the major export destinations of Indian fruits. The results showed that an exporting countries should export grapes to Peru, Spain and Chile; bananas to the Panama, Philippines and Ecuador; mangoes to Italy, Egypt and Australia; and, oranges to Thailand, Philippines and Mexico for generating higher revenue because in global market those countries were associated with highest export price with the stability. Globally, the export price elasticity was inelastic in all countries of grapes, oranges and bananas except Italy in oranges and panama in bananas. The study found that export price elasticity of mangoes was marginally higher in the Spain and the Netherlands. The study showed that the major destinations for Indian fruits are; USA, Germany and Netherlands for grapes; USA, Belgium and Germany for bananas; USA, the Netherlands and Viet Nam for mangoes; and, Germany, France and Netherlands for oranges. Globally, the current study gave useful data to comprehend competition of prices for fruits to importing countries. This study may assist in preparing major price strategies and policies on fruits and also assisted in foreign earnings for all nations.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.