In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

In a particle swarm with a fixed kinetic energy, the constituent particles move randomly and their velocity magnitudes follow a Maxwell distribution characterized by specific parameters. Within a certain time frame, particles in a sub-swarm may exhibit a bias in their movement direction. Thus, the particles may exhibit a special characteristic (biased random motion), where the group velocity in a particular direction remains constant u. For this biased particle swarm, composed of randomly moving particles with a fixed average speed c, particles have a higher probability of moving in a specific direction. Conversely, their likelihood of moving in all other directions is equally reduced. This study starts from the perspective of biased random walks and using Mathematica software proves that the diffusion rate of particles (in the reference frame R_u observed from R₀) in all directions is slower than that of an unbiased particle swarm with the same average speed c. Specifically, the degree of reduction is determined by the Lorentz-like factor. Lastly, we present the Ito equation for this biased random motion and provide associated verification examples. This study aims to serve as a reference for comprehending the underlying principles of the special relativity effect.

Two representable substructural logics ${\rm {\bf UL}}_\omega $ and ${\rm {\bf IUL}}_\omega $ are logics for finite UL and IUL-algebras, respectively. In this paper, the standard completeness of ${\rm {\bf UL}}_\omega $ and ${\rm {\bf IUL}}_\omega $ is proved by the method developed by Jenei, Montagna, Esteva, Gispert, Godo and Wang. This shows that ${\rm {\bf UL}}_\omega $ and ${\rm {\bf IUL}}_\omega $ are substructural fuzzy logics.

This paper aims to address the exponential stability and stabilization problems for a class of delayed nonlinear Markov jump systems under randomly occurring Denial-of-Service (DoS) attack and packet loss. Firstly, the stochastic characteristics of DoS attack and packet loss are depicted by the attack success rate and packet loss rate. Secondly, a Period Observation Window (POW) method and a hybrid-input strategy are proposed to compensate for the impact of DoS attack and packet loss on the system. Thirdly, A Dynamic Event-triggered Mechanism (DETM) is introduced to save more network resources and ensure the security and reliability of systems. Then, by constructing a general common Lyapunov functional and combining with the DETM and other inequality analysis techniques, the less conservative stability and stabilization criteria for the underlying systems are derived. In the end, the effectiveness of our result is verified through a numerical example.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

This study evaluates audiogenic epilepsy in Krushinsky-Molodkina rats using a wireless EEG system to overcome the limitations of traditional methods that restrict animal movement. Nine male KM rats, prone to audiogenic seizures, were implanted with electrodes in areas critical for seizure activity (inferior colliculus, ventrolateral periaqueductal gray, dorsal area of the secondary auditory cortex, and motor cortex). This setup allowed for the observation of seizures without movement restriction. Results showed that targeted neural intervention via electrode implantation reduced the intensity of convulsive seizures in half of the subjects, suggesting a potential therapeutic approach. The severity of seizures was influenced by the pre-phonostimulation EEG background activity in specific brain regions, identifying them as key in the genesis and generalization of seizures. Observations of dual generalized seizure waves and induced hyperkinesis challenge conventional epilepsy models and suggest new directions for research and therapy development.

The ordinary 3D wave equation for nondissipative, homogeneous, isotropic media admits solutions where the point sources are permitted to move, but it does not admit solutions where the receiver is allowed to move. To overcome this limitation, the new wave equation is derived, permitting both the receiver and the source to move. This new wave equation is a generalization of the standard wave equation, and it reduces to the standard wave equation when the receiver is at rest. To derive this new wave equation, we first mathematically define a diverging spherical wave caused by the stationary point source. From this purely mathematical definition, the wave equation for the stationary source and the moving receiver is derived together with the corresponding free-space Green's function. Utilizing the derived Green's function, it was shown that this new wave equation also permits the solutions where both the receiver and the source are permitted to move. In conclusion, this paper demonstrates that, instead of an ordinary wave equation, the wave equation for the moving source and the moving receiver governs the waves emitted by the moving point sources and received by the moving receivers.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Background: The accurate diagnosis of regional lymph node metastasis is critical for guiding treatment decisions in head and neck cancer patients. Despite advances in imaging techniques, detecting nodal metastasis remains challenging, leading to potential undertreatment or overtreatment. This systematic review aims to identify molecular markers associated with occult metastasis in Head and Neck Squamous Cell Carcinoma (HNSCC) patients. Methods: The present research was conducted following PRISMA guidelines. Prospero registration nr. CRD42024522985. Results: Through a comprehensive literature search and review process, 634 articles were considered, 103 of them were finally included. Conclusions: Several promising markers were identified, including miR-205, DSG3, pan-CK AE1/AE3, HPV-16, Activin-A, Cyclin D1, and NPL that demonstrated effectiveness across multiple studies. Future research should focus on exploring combination scoring systems to improve diagnostic precision and optimize treatment selection in HNSCC patients.

Due to the complexity of the microstructure of porous media, it is of great significance to explore the heat transport mechanism in porous media in many engineering applications. In this study, an expression for effective thermal conductivity（ETC） of porous media with randomly distributed damaged tree-like bifurcation networks is derived based on the theory of thermodynamics and fractal features of tree-like bifurcation networks. We investigate the effect of heat conduction and heat convection in porous media with randomly distributed damaged tree-like bifurcation networks on the ETC of the porous media. It is found that our fractal model is in good consistency with the existing available experimental data. In addition, the influence of the micro-structural parameters of the model on heat transfer in the porous media have been analyzed in detail. The research results can provide significant theoretical guidance for the development and design of heat transfer systems.

Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag) ternary nanocomposite with effective electrons transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT) and mesoporous TiO2/RGO (MTG), the ternary mesoporous TiO2/RGO/Ag (MTGA) nanocomposite exhibited superior photocatalytic performance for the degradation of MB under visible light, and the degradation rate reached 0.017 min-1, which was 3.4 times higher than that of MTG. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR) to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of carriers. The establishment of MTGA ternary nanocomposite make the three components act synergistic effect to enhance the photocatalytic performance.

In previous papers we have derived equations of motion with radiation terms and proved the existence-uniqueness of periodic solution of the 3-body problem of classical electrodynamics. The number of equations of motion – 12 is more than the number of unknown functions – 9. It turns out that 9 equations are independent and the rest 3 ones are consequences of them. These three equations have a solution and they give the expressions for the energy of the moving particles. The main goal of the present paper is to estimate the energy of rounding about the nuclei particles and compare it with the values given by quantum mechanics.

The rapid development of specific-purpose Large Language Models (LLMs), such as Med-PaLM, MEDITRON-70B, and Med-Gemini, has significantly impacted healthcare, offering unprecedented capabilities in clinical decision support, diagnostics, and personalized health monitoring. This paper reviews the advancements in medicine-specific LLMs, the integration of Retrieval-Augmented Generation (RAG) and prompt engineering, and their applications in improving diagnostic accuracy and educational utility. Despite the potential, these technologies present challenges, including bias, hallucinations, and the need for robust safety protocols. The paper also discusses the regulatory and ethical considerations necessary for integrating these models into mainstream healthcare. By examining current studies and developments, this paper aims to provide a comprehensive overview of the state of LLMs in medicine and highlight the future directions for research and application. The study concludes that while LLMs hold immense potential, their safe and effective integration into clinical practice requires rigorous testing, ongoing evaluation, and continuous collaboration among stakeholders.

Adenomyosis, a benign gynecological condition characterized by the infiltration of endometrial tissue into the myometrium, poses significant challenges to women's reproductive health. Recently, the landscape of adenomyosis diagnosis transformed significantly, thanks to advancements in imaging technologies such as transvaginal ultrasound and magnetic resonance imaging. This lead to a noticeable shift in the demographic profile of patients diagnosed with adenomyosis, including younger women of reproductive age who frequently present with a diverse array of symptoms. Approximately 20% of women are affected by adenomyosis. Adenomyosis manifests with various subtypes, distinct epidemiological profiles, symptomatology, and treatment responses, necessitating tailored approaches for optimal management. Despite its clinical significance, adenomyosis remains understudied, resulting in a significant disparity in research and literature compared to other gynecological conditions. The severity of adenomyosis is compounded when coexisting with endometriosis, particularly deep infiltrating endometriosis (DIE), leading to exacerbated fertility issues and severe symptomatology. The wide range of symptoms, including adverse pregnancy outcomes such as pre-eclampsia, highlights its wider impact and emphasizes the need for increased awareness of the condition. Furthermore, Adenomyosis is frequently associated with treatment failure in endometriosis, contributing to dienogest resistance, elevated discontinuation rates, and persistent pain post endometriosis surgery. Additionally, the lack of specific treatments tailored to adenomyosis poses a considerable challenge in clinical management.

An original approach has been proposed for designing a nanofibrous (NFs) layer using UV-cured polyvinylpyrrolidone (PVP) as a matrix, incorporating mesoporous graphene carbon (MGC) nanopowder both inside and outside the fibres, creating a sandwich-like structure. This architecture is intended to selectively adsorb and detect acetic acid vapours, which are known to cause health issues in exposed workers. The nanocomposite MGC-PVP-NFs layer was fabricated through electrospinning deposition onto interdigitated microelectrodes (IDEs) and stabilised under UV-light irradiation. To enhance the adhesion of MGC onto the surface of the nanocomposite polymeric fibres, the layer was dipped in a suspension of polyethylenimine (PEI) and MGC. The resulting structure demonstrated promising electrical and sensing properties, including rapid responses, high sensitivity, good linearity, reversibility, repeatability, and selectivity towards acetic acid vapours. Initial testing was conducted in a laboratory using a bench electrometer, followed by validation in a portable sensing device based on consumer electronic components (by ARDUINO®). This portable system was designed to provide a compact, cost-effective solution with high sensing capabilities. Under room temperature and ambient air conditions, both laboratory and portable tests exhibited favourable linear responses, with detection limits of 0.16 and 1 ppm, respectively.

This study uses machine learning to identify key factors influencing the cost-effectiveness of over-the-counter (OTC) medications. By developing a novel cost-effectiveness rating (CER) from user ratings and prices, we analyzed data from Amazon. The findings indicate that FSA/HSA eligibility, symptom treatment range, safety warnings, special effects, active ingredients, and packaging size significantly impact cost-effectiveness across cold, allergy, digestion, and pain relief medications. Medications eligible for FSA or HSA funds, treating a broader range of symptoms, and having smaller packaging are perceived as more cost-effective. Cold medicines with safety warnings were found to be cost-effective due to their lower average price and effective ingredients like phenylephrine and acetaminophen. Allergy medications with kid-friendly features showed higher cost-effectiveness, and ingredients like calcium, famotidine, and magnesium boosted the cost-effectiveness of digestion medicines. These insights help consumers make informed purchasing decisions and assist manufacturers and retailers in enhancing product competitiveness. Overall, this research supports better decision-making in the pharmaceutical industry by highlighting factors that drive cost-effective medication purchases.

In the energy-momentum density expressions for a relativistic perfect fluid with a bulk motion, one comes across a couple of pressure-dependent terms, which though well known, are to an extent, lacking in their conceptual basis and the ensuing physical interpretation. In the expression for the energy density, the rest mass density along with the kinetic energy density of the fluid constituents due to their random motion, which contributes to the pressure as well, are already included. However, in a fluid with a bulk motion, there are, in addition, a couple of explicit, pressure-dependent terms in the energy-momentum densities, whose presence to an extent, is shrouded in mystery, especially from a physical perspective. We show here that one such pressure-dependent term appearing in the energy density, represents the work done by the fluid pressure against the Lorentz contraction during transition from the rest frame of the fluid to another frame in which the fluid has a bulk motion. This applies equally to the electromagnetic energy density of electrically charged systems in motion and explains in a natural manner an apparently paradoxical result that the field energy of a charged capacitor system decreases with an increase in the system velocity. The momentum density includes another pressure-dependent term, that represents an energy flow across the system, due to the opposite signs of work being done by pressure on two opposite sides of the moving fluid. From Maxwell's stress tensor we demonstrate that in the expression for electromagnetic momentum of an electric charged particle, it is the presence of a similar pressure term, arising from electrical self-repulsion forces in the charged sphere, that yields a natural explanation for the famous, more than a century old, 4/3 factor in the electromagnetic mass.

This paper investigates the randomly stopped sums, minima and maxima of heavy- and light-tailed random variables. The conditions on the primary random variables, which are independent but generally not identically distributed, and counting random variable are given in order that the randomly stopped sum, random minimum and maximum is heavy/light tailed. The results generalize some existing ones in the literature. The examples illustrating the results are provided.

The acceleration of the universe is described as a consequence of the extrinsic curvature of the space-time embedded in a bulk space, defined by the Einstein-Hilbert. Using the linear approximation of Nash-Green theorem, we obtain the related perturbed equations in which just the gravitational-tensor field equations contribute to propagation of cosmological perturbations. In accordance with Big Bang Nucleosynthesis and solar constraints, we calculate numerically the effective Newtonian function Geff to constrain the related parameters of the model. We numerically solve the growth density equation for two possible family of solutions leading to an interesting overdensity and, in some cases, a mild damping of the growth profiles, with a top amplification of the growth perturbations around 14% in comparison with LCDM model and quintessence. The effective gravitational Phi and Newtonian curvature Psi are also analysed showing mild perturbations in early times induced only by the extrinsic curvature differently from the LambdaCDM standards.

Auger electrons (AEs) represent an intriguing topic in the field of radionuclide therapy. They are emitted by several radionuclides commonly used in nuclear medicine (indium-111, iodine-123, iodine-125), allowing for highly localized energy deposition and thus exerting a radiotoxic effect on specific cellular and sub-cellular targets. However, due to their short range in matter, AEs have had limited use in therapeutic applications so far. In recent years, the synthesis of various radiopharmaceuticals capable of binding to the enzyme poly(ADP-ribose) polymerase 1 has reignited interest in this type of therapy, laying the groundwork for a theranostic approach based on radionuclides emitting AEs. The enzyme PARP-1 operates enzymatically in close proximity to DNA that represents the prime target of radionuclide therapies. Following this trend, several PARP-targeted radiopharmaceuticals for AE-based theranostics have been developed. We provide an updated overview of preclinical studies focused on the applications of this new theranostic approach in glioblastoma, breast, prostate and ovarian carcinoma, and pancreatic adenocarcinoma.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Predicting human trajectories poses a significant challenge due to the complex interplay of pedestrian behavior, which is influenced by environmental layout and interpersonal dynamics. This complexity is further compounded by variations in scene density. To address this, we introduce a novel dataset from the Festival of Lights in Lyon 2022, characterized by a wide range of densities (0.2-2.2 ped/m2). Our analysis demonstrates that density-based classification of data can significantly enhance the accuracy of predictive algorithms. We propose an innovative two-stage processing approach, surpassing current state-of-the-art methods in performance. Additionally, we utilize a collision-based error metric to better account for collisions in trajectory predictions. Our findings indicate that the effectiveness of this error metric is density-dependent, offering prediction insights. This study not only advances our understanding of human trajectory prediction in dense environments but also presents a methodological framework for integrating density considerations into predictive modeling, thereby improving algorithmic performance and collision avoidance.

Under different pathophysiological conditions endothelial cells lose endothelial phenotype and gain mesenchymal cell-like phenotype via a process known as endothelial-to-mesenchymal transition (EndMT). At the molecular level, endothelial cells lose the expression of endothelial cell-specific markers such as CD31/platelet-endothelial cell adhesion molecule, von Willebrand factor, and vascular-endothelial cadherin and gain the expression of mesenchymal cell markers such as α-smooth muscle actin, N-cadherin, vimentin, fibroblast specific protein-1 and collagens. EndMT is induced by numerous different pathways triggered and modulated by multiple different and often redundant mechanisms in a context-dependent manner depending on the pathophysiological status of the cell. EndMT plays an essential role in embryonic development, particularly in atrioventricular valve development, however, EndMT is also implicated in pathogenesis of several genetically determined and acquired diseases including malignant, cardiovascular, inflammatory, and fibrotic disorders. Among cardiovascular diseases aberrant EndMT is reported in atherosclerosis, pulmonary hypertension, valvular disease, fibroelastosis and cardiac fibrosis. Accordingly, understanding the mechanisms behind cause and/or effect of EndMT to eventually target EndMT appears to be a promising strategy to treat aberrant EndMT-associated diseases. However, this approach is limited by a lack of precise functional and molecular pathways, causes and/or effects, and lack of robust animal model and human data about EndMT in different diseases. Here, we review different mechanisms in EndMT and the role of EndMT in various cardiovascular diseases.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

Histone changes that are adjustable and transmitted without altering the DNA sequence are part of epigenetic control. In many disorders, most famously malignancy, abnormal genetic information is seen as a result of mismanagement of typical epigenetic mechanisms. A paradigm change in the diagnosis and treatment of cancer has been brought about by recent discoveries about the processes of epigenetic modifications, chromatin remodeling, and noncoding RNAs implicated in the changed expression patterns of tumor cells. There is a significant increase in the search for drugs that could alter the epigenetic environment altered by tumor cells and benefit from their therapeutic potential. Phytochemicals with a high concentration of naturally produced phenol molecules known as flavonoids can regulate genomic processes. Understanding the precise epigenetic alterations brought on by flavonoid-mediated mechanisms is necessary to develop combination therapy techniques and genomic therapies for cancer. This article aims to thoroughly examine the epigenetic modifications of flavonoids, including their anticancer properties.

Abstract: Dispersal strategies of a species can affect its invasion success. Investigation into the dispersal strategies of invasive species in relation to different factors helps our understanding of the invasion mechanisms and provides knowledge for population management and invasion evaluation. Tetranychus ludeni Zacher (Acari: Tetranychidae) is an invasive species, which is native to Europe but now cosmopolitan. Here, we examined the effects of age and density on dispersal in mated females. Our results show that older females with more eggs were more likely to disperse and moved longer distances than younger ones with fewer eggs. Older females spread most of their eggs out of the natal habitats and over longer distances, which reduced competition and increased offspring fitness. Females significantly increased dispersal probability and distance with the increase of population density to avoid crowding. The synchronization of dispersal and reproduction, along with the positive density-dependent dispersal strategy, may facilitate habitat colonization and invasion speed of T. ludeni.

Molecular-scale density fluctuations at equilibrium produce cavities in a liquid and can be analyzed to shed light on the statistics of the number of molecules occupying observation volumes of increasing radius. An information theory approach led to the conclusion that these probabilities should follow a Gaussian distribution function. This prediction has been confirmed by computer simulations in different liquid models if the size of the observation volume is not large. The reversible work of cavity creation is exactly linked to the probability of finding zero molecules in a given observation volume. The Gaussian formula for the latter probability is scrutinized to arrive at the enthalpy and entropy changes associated with cavity creation. The reversible work of cavity creation has a purely entropic origin due to the solvent-excluded volume effect produced by the inaccessibility of a given region of the configurational space. The consequent structural reorganization of liquid molecules leads to exactly compensating enthalpy and entropy changes. These results are in line with those obtained in a direct statistical mechanical study by Lee.

This study is based on the clamor of fish farmers for a cheaper fish feed alternative to current commercial feeds. At present, 70-80% of aquaculture costs come from feed cost, keeping farmers' income below their expectation. This study aimed to find alternative feeds or supplementary feeds that can perform similarly to the existing commercial feeds thereby reducing farmer expense and cutting down their cost of production and increasing their profitability. To do that, various indigenous raw materials were selected based on an earlier study which could result in a better feed alternative. The formulations for the study included four grow-out treatments mainly: control (commercial feed), taro+control (powdered Colocasia esculenta+commercial fish feed), bloodmeal (formulated fish feed based on bloodmeal), banana stem+control (chopped banana stem+commercial fish feed). A total of 12,000 fingerlings initially weighing 16 g (TL=10 cm) individually were assigned randomly to the four treatments (3000 in each cage measuring 6 x 6 m). Week zero was used for acclimation period, and fingerlings were fed with commercial fish feed. Then the first week used the treatment diets which were adjusted based on average body weight and sampled weekly (ABW=23g; TL=11 cm). The result of the study first showed significant differences between treatments on their fourth week in terms of the diet treatments (MS=0.103, df=3, F=4.12, P=0.0076) with the control and the taro+control showing no difference in terms of weight and length (TC vs CF; P=0.4524). But during the fifth week, the bloodmeal treatment showed increased weight and length for fish sampled (MS=0.109, df=3, F=4.10, P=0.0076) and provided similar weight and length as those from the taro+control and the control (TC vs CF; P=0.3721 and BM vs CF; P=0.0587). During the succeeding weeks, there were no significant differences between feed treatments from 6th weeks onwards, whether with weight [MS=0.130, df=3, F=1.14, P=0.333] or total length of the treatments [MS=0.008, df=3, F=0.40, P=0.75]. The FCR ratio showed taro (1.81) as lowest, followed by blood meal (2.09), and control (2.24) and then banana stem (2.84). In terms of weight gain, fish from the bloodmeal treatment gained the highest (236.97 g), followed by control (223.33 g), then taro (217.67 g) and banana stem (196.99 g). As a result, we find that the tested treatments such as bloodmeal formulated feed, taro+commercial feed, and banana stem+commercial feed can serve as an alternative to purely commercial fish feeds. Cost-benefit analysis showed that a better gross profit margin of 42% and cost-benefit ratio of 1.37 was observed in taro+commercial feed diet.

Spray penetration into citrus canopies is critical for adequate coverage and deposition to ensure effective pest control. However, mismatch of air assistance to target canopy characteristics can lead to unintended spray loss through over penetration. To evaluate the effect of air assistance on on-target deposition, two sprayers (surrogates for airflow rates) were used to apply a fluorescent tracer dye solution @ target concentration of 300 ppm to 16 medium foliage density tree blocks in a commercial mandarin orchard. The complete factorial experiment in three replications comprised two ground speeds (1.6 and 4.8 km/h), two disc-core nozzles (TeeJet® D3-25 and D6-45), and either one or two nozzle rows to obtain a wide range of application rates (496 to 9,719 L/ha). Dye deposition significantly decreased with canopy depth (p=<0.001) by nearly 7 times across the 3.4-m-wide canopies but was not significant over 1.2 to 2.2 m sampling height (p=0.867). Deposition obtained with the low airflow rate sprayer was significantly greater (p=<0.001) than that obtained with the high airflow rate sprayer over the dose range likely due to too much air pushing out spray droplets. This study underscores the importance of matching the air assistance of orchard sprayers to the target canopy.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

Partial Differential Equations (PDEs) constitute a fundamental framework for modeling various physical phenomena across diverse fields such as physics, engineering, and finance. Solving PDEs accurately and efficiently remains a significant challenge, particularly when dealing with complex systems or high-dimensional data. In this paper, we present a novel approach based on deep learning techniques to investigate the effective factors in solving PDEs. Our methodology leverages the expressive power of deep neural networks to learn and represent the underlying relationships between input parameters and the solutions of PDEs. By incorporating domain knowledge into the network architecture and training process, our approach aims to provide insights into the key factors influencing the solution of PDEs. We demonstrate the effectiveness of our method through numerical experiments on various PDEs, showcasing its capability to identify important features and improve predictive accuracy. Our findings suggest that deep learning techniques offer a promising avenue for understanding and analyzing the complex dynamics inherent in PDEs, paving the way for enhanced computational methods in scientific and engineering applications.

Human activities continuously alter the delivery of ecosystem services (ESs), which play a crucial role in human well-being. There is a pressing need for effective ecological management strategies that consider the spatial heterogeneity of ESs to support the transition from trade-offs to synergies. This study focuses on the Haba River Basin and examines characteristics of land use change and the shift from trade-offs to synergies. The results indicate that from 1990 to 2000, the initial phase of land development, 10.65% of the land experienced change. Subsequently, during the intensive period of land development from 2000 to 2010, 30.29% of the land underwent significant transformation, with approximately 78% of grassland, sparse grassland, forested land, and desert converted into arable land. However, between 2010 and 2020, as the focus shifted towards the establishment of native vegetation and the intensity of land development decreased, only a small percentage (3.65%) of the total area underwent changes. Based on an in-depth analysis of spatial heterogeneity from 1990 to 2020, it is believed there has been a shift from trade-offs to co-benefits between 2000-2010 and 2010-2020. The years 2010 and 2020 were pivotal time nodes for the transition from trade-offs to synergies and for reducing trade-offs, with NPP identified as a critical driving factor for Comprehensive ES （CES） functions. By considering the trade-offs/synergies relationship and hotspots of ecological service functions, combined with unified water resource management policies, comprehensive ecological management measures tailored to different regions are proposed. These measures have facilitated the implementation of robust ecological protection policies to shift ES development from trade-offs to synergies in arid areas, thereby enhancing overall ecosystem service functions in the Haba River Basin. The research findings offer crucial scientific support and guidance for ecosystem management in arid areas, particularly within Central Asia.

Leveraging the liquid phase immiscibility effect and phase diagram calculations, a sequence of alloy powders with varying Fe content was designed and fabricated utilizing gas atomization method. Microstructural characterizations, employing SEM, EDS, and XRD analyses, revealed the successful formation of incomplete shell on the surfaces of Al-Bi-Fe powders, obviating the need for Sn doping. This study systematically investigated the microstructure, hydrolysis performance, and hydrolysis process of these alloys in deionized water. Notably, Al-10Bi-7Fe exhibited the highest hydrogen production, reaching 961.0 Nml/g, while Al-10Bi-10Fe demonstrated the peak conversion rate at 92.99%. The hydrolysis activation energy of each Al-Bi-Fe alloy powder was calculated using the Arrhenius equation, indicating a reduction in activation energy achieved through Fe doping.

Detecting volatile organic compounds (VOCs) emitted from different plant species and their or-gans can provide valuable information about plant health and environmental factors that affect them. For example, limonene emission can be a biomarker to monitor plant health and detect stress. Traditional methods for VOC detection encounter challenges, prompting the proposal of novel approaches. In this study, we proposed integrating electrospinning, molecular imprinting, and conductive nanofibers to fabricate limonene sensors. In detail, polyvinylpyrrolidone (PVP) and polyacrylic acid (PAA) served here as fiber and cavity formers, respectively, with multi-walled carbon nanotubes (MWCNT) enhancing conductivity. We developed one-step monolithic molecularly imprinted fibers, where S(-)-limonene was the target molecule using electrospinning technique. The functional cavities were fixed using UV curing method, followed by a target mol-ecule washing. This procedure enabled the creation of recognition sites for limonene within the nanofiber matrix, enhancing sensor performance and streamlining manufacturing. Humidity was crucial for sensor working, with optimal conditions at about 50% RH. The sensors rapidly re-sponded to S(-)-limonene, reaching a plateau within 200 seconds. Enhancing fiber density im-proved sensor performance, resulting in a lower limit of detection (LOD) of 137 ppb. However, excessive fiber density decreased accessibility to active sites, thus reducing sensitivity. Remarka-bly, the thinnest mat on the fibrous sensors created provided the highest selectivity to limonene (Selectivity Index: 72%) compared to other VOCs, such as EtOH (used as a solvent in nanofiber development), aromatic compounds (toluene), and two other monoterpenes (α-pinene and linalo-ol) with similar structure. These findings underscored the potential of the proposed integrated approach for selective VOC detection in applications such as precision agriculture and environ-mental monitoring.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

As society becomes more reliant on Lithium-ion (Li-ion) batteries, state-of-health (SOH) estimation will need to become more accurate and reliable. Therefore, SOH modelling is in the process of shifting from using simple and continuous charge/discharge profiles, to more dynamic profiles constructed to mimic real operation, when ageing the Li-ion batteries. However, in most cases, when ageing the batteries, the same exact profile is just repeated until the battery reaches its end-of-life. Using data from batteries aged in this fashion to build a model, there is a very real possibility that the model will rely on the built-in repetitiveness of the profile. Therefore, this work will examine the dependence of the performance of a multiple linear regression on the number of charges used to train the model, and their location within the profile used to age the batteries. The investigation shows that it is possible to build models using randomly selected partial charges while still reaching errors as low as 0.5%. Furthermore, it shows that only two randomly sampled partial charges are needed to achieve errors of less than 1%. Lastly, as the number of randomly sampled partial charges used to create the model increases, then the dependence on particular partial charges tends to decrease.

Hydrogen is now recognized as the primary alternative to fossil fuels due to its renewable, safe, high energy density and environmentally friendly properties. Efficient hydrogen production through water splitting has laid the foundation for sustainable energy technologies. However, when hydrogen production is scaled up to industrial levels, operating at high current densities introduces unique challenges. It is necessary to design advanced electrocatalysts for hydrogen evolution reaction (HER) under high current densities. This review will briefly introduce chal-lenges posed by high current densities on electrocatalyst, including catalystic activity, mass dif-fusion and catalyst stability. In an attempt to address these issues, various electrocatalyst design strategies are summarized in detail. In the end, our insights into future challenges for efficient large-scale industrial hydrogen production from water splitting are presented. This review is expected to guide the rational design of efficient high current density water electrolysis electro-catalysts and promote the research progress of sustainable energy.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

This work focuses on the theoretical study of the effect of entanglement in the Yttrium Barium Copper Oxide (YBCO) superconductor on the critical current density, critical magnetic field, and penetration depth. Using the Ginzburg Landau (GL) theory, the expression for the GL coherence length, the critical current density, the lower critical magnetic field (Hc1), and the upper critical magnetic field (Hc2) for the entangled superconducting YBCO was obtained. At zero external magnetic fields, YBCO was found to undergo a transition from the normal state to the superconducting state at 93K and returned to normal. We found a direct relationship between the GL coherence length penetration depth and the temperature of the entangled superconducting YBCO. The graphs of the lower critical magnetic field (Hc1) and critical current density against temperature show a non-linear dependence.In contrast, the graph of the upper critical magnetic field (Hc2) against temperature (T) shows the linear dependence, which is in agreement with existing theoretical observations. On the other hand, the graph of critical current density against the distance of separation between the entangled electrons that form a cooper pair showed that the critical current density increases between 1.8 and 6 nanometers attaining a constant value after reaching 7 nanometers for infinite distances. Finally, for lower critical fields, the magnetic field decreases between 1.5 to 6 nanometers attaining a constant value of the magnetic field, for infinite values of distance of separation between the entangled pair of electrons.

Climate change, increasing global food needs, and decreasing global resources brought a new era to human every-day live with a strong turn to circular economy and sustainability. Food packaging and preservation is an important global sector where enchanced research is carried out. New methods such as active packaging and chemical preservatives replacement are of major interest. Many researchers were published studies about active packaging films, replacement of chemical preservatives with natural originated extracts, and novel incorporation procedures. Sequentially to our and other scientists’ previous work, in this paper we present the results of the improvement which was achieved by incorporating the developed nanohybrid of natural-halloysite/carvacrol-extract, the pure natural carvacrol extract and the commonly used low-density-polyethylene. The well known corona-treatment procedure was employed to produced the optimum final film and the results shown that the low-density-polyethylene incorporated with natural-halloysite/carvacrol-extract nanohybrid and coated external with extra carvacrol extract exhibited aproximatelly 100% higher Young-Modulus values, slightly decreased ultimate strength by 20%, and almost stable elonation at break properties. The water-vapor and oxygen barrier increased by 40%. Finally, the antioxidant activity of the corrona-treated film increased by 28% compared to the similar but untreated product because of the lower release rate of the carvacrol.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

In the literature of Low-Energy Nuclear Reactions (LENR), particle tracks in photographic emulsions (and other materials) associated with certain electrical discharges have been reported. Some Russian and French researchers have considered these particles to be magnetic monopoles. These tracks correspond directly to tracks created with a simple uniform exposure to photons without an electrical discharge source. This simpler method of producing tracks supports a comprehensive exploration of particle track properties. Out of 750 exposures with this method, elliptical particle tracks were detected, 22 of which were compared to Bohr-Sommerfeld electron orbits. Ellipses fitted to the tracks were found to have quantized semi-major axis sizes with ratios of ≈n²/α² to corresponding Bohr-Sommerfeld hydrogen ellipses. This prompts inquiry relevant to magnetic monopoles due to the n²/α² force difference between magnetic charge and electric charge using the Schwinger quantization condition. A model using analogy with the electron indicates that the elliptical tracks could be created by a bound magnetically charged particle with mass m_m = 1.45 × 10^-3 eV/c², yet with superluminal velocities. Using a modified extended relativity model, m_m becomes the relativistic mass of a superluminal electron, with m₀ = 5.11 × 10^-3 eV/c², the fine structure constant becomes a mass ratio and charge quantization is the result of two states of the electron.

Background: The two-stage technique combining the Endoscopic Retrograde CholangioPancreatography (ERCP) with common bile duct (CBD) clearance carried out before the laparoscopic cholecystectomy represents the most common approach for CBD stones. Over time, different techniques have been proposed to manage cholecysto- choledocholithiasis (CCL) advantageously in one stage. Among these, the laparoendoscopic rendez-vous (LERV) addresses the CCL issue with a laparoscopic cholecystectomy with insertion of a guide wire performed at initial stage of the procedure, followed by the clearance of the bile duct carried out by the endoscopists. The goal of this study was to evaluate the efficacy and safeness of LERV procedure recording results and complications, also making a comparison between our results and current literature. Methods: We reviewed our experience of all consecutive patients with cholecysto-choledocholithiasis managed with LERV between January 2018 and December 2023. LERV success rate, operative time, length of hospital stay, stone recurrence, incidence of endoscopic and surgical complications were analysed. Results: A total of 120 patients underwent LERV in our facilities. We reported a 97% LERV success rate, 1.6% conversion-to-open rate, a median intraoperative time of 122 (range 95-220) min. The median hospital stay was 4 (range 2-38) days. An overall morbidity of 15% was reported (18/120): 15 Clavien-Dindo type 1/2, 2 type 3a and one type 3b. In two cases a re-operation during the hospital stay was necessary. At a median follow-up of 14 months (3-59) five patients experienced stone recurrence requiring redo-ERCP in two cases. Conclusion: LERV offers the significant advantage of a single stage procedure and hospitalisation along with a lower risk of post-ERCP pancreatitis, failed CBD cannulation and complications. Our experience confirms safety and effectiveness of the technique for CCL management.

In this study, MBBR, utilizing kaldnes as a media to attach and grow microorganisms, was used to treat organics in a Compact Septage Treatment Plant (CSTP). Seeding and acclimatization processes were done initially to ensure the microorganisms were able to grow and adapt well within their environments. This research was done to determine the time required for those processes, the optimum conditions, and the growth mechanism of microorganisms during the acclimatization process. Both processes were run in a batch mode. Changes in colour and weight of kaldnes were analyzed for the seeding stage; while COD, MLVSS, pH & temperature were observed for the acclimatization stage. Seeding and acclimatization were run for 6 and 16 days respectively. Acclimatization stage was halted when MLVSS, pH, temperature and COD reduction efficiency were stable. Three phases of microorganism growth were clearly observed in the end of the acclimatization stage, i.e., lag, constant increasing and declining rates. This indicated that microorganisms could adapt well with the MBBR system, and were ready to be utilized further to treat septage in the MBBR of the CSTP. Further research is required to investigate the efficacy of the MBBR with the acclimatized microorganisms in the CSTP.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

The amount and spatial distribution of foliage in a tree canopy have fundamental functions in ecosystems as they affect energy and mass fluxes through photosynthesis and transpiration. They are usually described by the Leaf Area Index (LAI) and the Leaf Area Density (LAD), which can be measured through a variety of methods, including voxel-based methods applied to LiDAR point clouds. A theoretical study recently compared the numerical errors arising from different voxel-based estimation methods for Plant Area Density (PAD) based on Beer’s law-based, contact frequency and Maximum-Likelihood Estimation, showing that the bias-corrected Maximum Likelihood Estimator was theoretically the most efficient. However, this earlier study i) ignored wood volumes; ii) neglected vegetation clumping inside the voxel; iii) ignored instrument characteristics in terms of effective footprint, iv) was limited to a single viewpoint. In practice, retrieving LAD from PAD is not straightforward, vegetation is not randomly distributed in volumes of interest, beams are divergent and forestry plots are usually sampled from more than one viewpoint, to mitigate the effect of occlusion. In the present short communication, we extend the previous efficient formulation to actual field conditions to i) account for the presence of both wood volumes and wood hits, ii) rigorously include correction terms for vegetation and instrument characteristics, iii) integrate multiview data. A numerical comparison with other methods commonly used to combine information from different viewpoints led to error reduction, especially in poorly-explored volumes, which are frequent in actual canopies. Beyond its concision, completeness and efficiency, this new formulation -which can be applied to multiview TLS, but also UAV LiDAR scanning - can help reducing errors in LAD estimation.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

BackgroundLiving donor liver transplantation offers comparable long-term results to cadaveric donor transplantation. This study analyzes the selection process of living liver donors at a Western transplant center that utilizes both donation forms. MethodsThis retrospective analysis examined potential living donors, collecting medical data and reasons for refusal, and divided patients by indication and urgency for transplantation. ResultsFrom January 2013 to December 2023, 594 potential living donors were assessed at Jena University Hospital. Of these, 124 living donor transplants were performed. During outpatient evaluation, 357 potential donors were excluded. Subsequently, 238 individuals underwent inpatient assessment, with 100 more being excluded. Main reasons for donor refusal included medical or psychological issues (n=160), disease progression in recipients (n=90), and recipient refusal or donor withdrawal (n=54). The evaluation process showed a trend towards considering more distant relatives and acquaintances as donor candidates with increasing severity of the recipient's disease.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

Background: Leishmaniasis is a significant global public health issue that is caused by parasites from Leishmania genus. With limited treatment options and rising drug resistance, there is a pressing need for new therapeutic approaches. Molecular chaperones, particularly Hsp90, play a crucial role in parasite biology and are emerging as promising targets for drug development. Objective: This study evaluates the efficacy of 17-DMAG in treating BALB/c mice from cutane-ous leishmaniasis through in vitro and in vivo approaches. Materials and Methods: We assessed 17-DMAG cytotoxic effect on bone marrow-derived mac-rophages (BMMΦ) and its effects against L. braziliensis promastigotes and intracellular amastigotes. Additionally, we tested the compound's efficacy in BALB/c mice infected with L. braziliensis via intraperitoneal administration to evaluate the reduction of lesion size and de-crease of parasite load in the ears and lymph nodes of infected animals. Results: 17-DMAG showed selective toxicity [selective index=432) towards Leishmania amastigotes, causing minimal damage to host cells. The treatment significantly reduced lesion sizes in mice and results in parasite clearance from ears and lymph nodes. It also diminished in-flammatory responses and reduced the release of pro-inflammatory cytokines (IL-6, IFN-g, TNF) and the regulatory cytokine, IL-10, underscoring its dual leishmanicidal and anti-inflammatory properties. Conclusion: Our findings confirm the potential of 17-DMAG as a viable treatment for cutaneous leishmaniasis and support further research into its mechanisms and potential applications against other infectious diseases.

This study was to identify clinical cancer biomarkers for recurrent gastric cancer survivors using artificial intel-ligence. From a hospital-based cancer registry database in Taiwan, the datasets of the incidence of recurrence and clinical risk features were included in 2476 gastric cancer survivors. We benchmarked Random forest with MLP, C4.5, AdaBoost, and Bagging algorithms on metrics and leveraged synthetic minority oversampling technique (SMOTE) for imbalanced dataset issues, cost-sensitive learning for risk assessment, and SHapley Additive ex-Planations (SHAP) for feature importance analysis in this study. Our proposed Random forest outperformed the other models with an accuracy of 87.9%, a recall rate of 90.5%, an accuracy rate of 86% and F1 of 88.2% on re-current category by a 10-fold cross-validation in a balanced dataset. We identified clinical features of recurrent gastric cancer, which are the top five features, stage, number of regional lymph node involvement, Helicobacter pylori, BMI(body mass index), and gender, which significantly affect the prediction model's output, are worth paying attention to in the following causal effect analysis. Using an artificial intelligence model, the risk factors for recurrent gastric cancer could be identified and cost-effectively ranked according to their feature importance. In addition, they should be crucial clinical features to provide physicians with the knowledge to screen high-risk patients in gastric cancer survivors as well.

A medium scale household in South Africa consumes about 1000 kWh on average, and ae household spend about 3000 ZAR per month on energy supply using grid electricity. Grid electricity. South Africa’s energy is supplied by a huge governmental organization. Statistical analyses indicate that projected increase of the cost of grid electricity in South Africa is about 30% per annum for the next five years. Our research show that Photo-Voltaic (PV) technology can offer a viable alternative, provided a large initial capital outlay can be made. The technology is user-friendly and easy to operate. It is calculated that the cost of electricity, capitalized over 20 years, considering an 80 % supply of needs and assuming 20 sunny days per month, is about 2.80 ZAR. The study also shows that utilizing a hybrid combination of renewable energies, such as combining PV supply with solar thermal energy absorbers, and converting thermal energy to electricity, as energy supply systems, could reduce the current cost of electricity per household in South Africa to about half of national grid supply prize, R1,50 per kWhr. The study also shows that water provides as a most viable medium to store energy, instead of using expensive battery technology to perform such functions.

Let {ξ1, ξ2. . . .} be a sequence of independent possibly differently distributed random variables defined on a probability space (Ω, F, P) with distribution functions {F_ξ1., F_ξ2 , . . .}. Let η be a counting random variable independent of sequence {ξ1, ξ2. . . .}. In this paper, we find conditions under which distribution function of randomly stopped sum Sη = ξ1 + ξ2 + . . . + ξη belongs to the class of generalized subexponential distributions.

As it turns out, both isotope scaling and density limits are phenomena closely linked to fluid closure. The necessity to include ion viscosity arises for both phenomena. Thus, we have added ion viscosity to our model. The experimental isotope scaling has been successfully recovered in our fluid model through parameter scans. Although ion viscosity typically exerts a small effect, the density limit is manifested by increasing the density by approximately tenfold from the typical experimental density. In our case, this increase originates from the density in the Cyclone base case. Notably, these phenomena would not manifest with a gyro-Landau fluid closure. The isotope scaling is nullified by the addition of a gyro-Landau term, while the density limit results from permitting ion viscosity to become comparable to the gyro-Landau term. The mechanism of zonal flows, demonstrated analytically for the Dimits upshift, yields insights into the isotope scaling observed in experiments. In our approach, ion viscosity is introduced in place of the Landau fluid resonances found in some fluid models. This implies that the mechanism of isotope scaling operates at the level of fluid closure in connection with the generation of zonal flows. The strength of zonal flows in our model has been verified, particularly in connection with the successful simulation of the nonlinear Dimits shift. Consequently, a role is played by our approach in the temperature perturbation part of the Reynolds stress.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

Recycling upholstery textiles is challenging due to the complexity of materials, which often include a mix of fabrics, foams, and adhesives that are difficult to separate. The intricate designs and layers in upholstered furniture make it labor-intensive and costly to dismantle for recycling. Additionally, contaminants like stains, finishes, and flame retardants complicate recycling. Despite these difficulties, recycling upholstery textiles is crucial to reducing landfill waste and conserving resources by reusing valuable materials. It also helps mitigate environmental pollution and carbon emissions associated with producing new textiles from virgin resources. The presented research aimed to establish the feasibility of incorporating textile fibers from waste artificial leather fibers from the upholstery furniture industry into the structure of high-density fiberboards. This approach positively contributes to carbon capture and storage (CCS) policy and mitigates the problem of such waste being sent to landfills. The research shows that while selected mechanical and physical parameters of the panels decrease with a rising content of recycled textile fibers, it is possible to meet proper European standard requirements by adjusting technological parameters such as nominal density.

The current treatment for cervico-facial cancer involves radio and/or chemotherapy. Unfortunately, cancer therapies can lead to local and systemic complications such as mucositis, which is the most common dose-dependent complication in the oral cavity and gastrointestinal tract. Mucositis can cause a considerably reduced quality of life in cancer patients already suffering from physical and psychological exhaustion. However, melatonin, whose role in the treatment of mucositis has recently been investigated, offers an effective alternative therapy in the prevention and/or management of radio and/or chemotherapy-induced mucositis. This review focuses on the pathobiology and management of mucositis in order to improve the quality of cancer patients’ lives.

Combinatoric measures of entropy capture the complexity of a graph, but rely upon the calculation of its independent sets, or collections of non-adjacent vertices. This decomposition of the vertex set is a known NP-Complete problem and for most real world graphs is an inaccessible calculation. Recent work by Dehmer et al. and Tee et al. identified a number of alternative vertex level measures of entropy that do not suffer from this pathological computational complexity. It can be demonstrated that they are still effective at quantifying graph complexity. It is intriguing to consider whether there is a fundamental link between local and global entropy measures. In this paper, we investigate the existence of correlation between vertex level and global measures of entropy, for a narrow subset of random graphs. We use the greedy algorithm approximation for calculating the chromatic information and therefore Körner entropy. We are able to demonstrate close correlation for this subset of graphs and outline how this may arise theoretically.

Urbanization growth has intensified the challenge of managing and treating increasing amounts of municipal solid waste (MSW). Landfills are commonly utilized for MSW disposal because of their low construction and operation costs. However, this practice produces huge volumes of landfill leachate, a highly polluting liquid rich in ammoniacal nitrogen (NH3-N), organic compounds and various heavy metals, making it difficult to treat in conventional municipal wastewater treatment plants (WWTPs). In recent years, research has shown that microbial biofilms, developed on carriers of different materials and called “Moving Bed Biofilm Reactors” (MBBRs), may offer promising solutions for bioremediation. This study explored the biofilm development and the nitrification process of moving bed biofilms (MBBs) obtained from high am-monia-selected microbial communities. Using Crystal Violet Staining and Confocal Laser-Scanning Microscopy, we followed the biofilm formation stages correlating nitrogen removal to metagenomic analyses. Our results indicate that MBBs unveiled a 10-fold more enhanced nitrification rate than the dispersed microbial community pre-sent in the native sludge of the Porto Sant’Elpidio (Italy) WWTP. Four bacterial families, Chitinophagaceae, Comamonadaceae, Sphingomonadaceae, and Nitrosomona-daceae accumulate in structured biofilms and significantly contribute to the high ammonium removal rate of 80% in 24 hours as estimated in leachate-containing wastewaters.

To identify factors associated with interstitial lung disease (ILD) in patients with systemic sclerosis (SSc) and build an algorithm to better define this association, for a personalized application in clinical practice. Methods. 78 SSc patients underwent HRCT to assess ILD. Demographic, clinical and laboratory variables were collected, focusing on those associated either directly or indirectly with lung involvement. The discriminant value of each variable was determined using the operating characteristic curves (ROC) and included in a model to estimate the strength of ILD association in SSc. Results. Thirty-three (42.31%) patients showed ILD on HRCT. DLco, M-Borg, GERD-Q, and capillary density were significantly associated with the presence of ILD-SSc. A model including these variables had a coefficient of determination (R2) of 0.697. DLco had an AUC of 0.861 (p<0.001) with a cut-off ≤72.3% (sensitivity 78.8%, specificity 91.1%, +LR 8.86). The m-Borg scale showed an AUC of 0.883 (p<0.001) with a cut-off >2 (sensitivity 84.8%, specificity 82.2%, +LR 4.77), GERD-Q had an AUC of 0.815 (p<0.001) with a cut-off >7 (sensitivity 72.7%, specificity 86.7%, +LR 5.45). The capillary density showed an AUC of 0.815 (p<0.001) with a cut-off ≤4.78 (sensitivity 87.9%, specificity 68.9%, +LR 2.82). Based on the pre-test probability values, these four variables were applied to Fagan's nomogram to calculate the post-test probability of this association. Conclusions. Our study identified four associated clinical factors of ILD in SSc patients. Moreover, their inclusion in an algorithm for the post-test probability, tailored to the specific patients’ characteristics, significantly increases the ability to find out the presence of SSc-ILD.

We conducted a study to determine if antenatally collected maternal urine cotinine (a me- 13 tabolite of nicotine) measurements can be used to assess the neonatal impact of nicotine exposure 14 during pregnancy. This was a prospective longitudinal cohort of mother-infant dyads. Only term 15 singleton pregnancies were included. The primary outcome measure was the correlation between 16 maternal urine cotinine and infant birth weight. We analysed data from 238 mother-neonates' dy- 17 ads. Urine cotinine was detected in 50.4 % (120/238) women from the whole cohort, but only 16% 18 (38/238) self-reported as smokers (chi-square 39.7, p<0.0001), and these women had significantly 19 smaller babies (p=0.010). There was a significant negative correlation between maternal urine co- 20 tinine and birth weight (Spearman's coefficient = -0.0226, p=0.013). Female babies born to women 21 with nicotine in the urine were significantly smaller (p= 0.001). The number of women exposed to 22 nicotine during late pregnancy (measured in urine) was markedly higher than self-reported and 23 National smoking percentages, suggesting an urgent need for improvement of medical record re- 24 porting on smoking habits to better assess neonatal outcomes.

Recent technological advancements in conservation genetics and genomics have resulted in diverse tools for aiding conservation of species. The precision and resolution of high throughput sequencing technologies provide valuable insights to aid conservation decisions, but these technologies are often financially unfeasible or unavailable in resource constrained countries. Inter-Simple Sequence Repeat (ISSR) markers, when combined with sensitive automated detection systems, provide a simple, cheap means to investigate genetic diversity and discriminate closely related species. Here we apply this technology to assess genetic diversity and taxonomic delimitation in the Encephalartos eugene-maraisii species complex, a highly threatened, taxonomically dubious group of cycads in South Africa. Our analyses support taxonomic singularity of E. dyerianus, E. dolomiticus and E. eugene-maraisii. Relationships between E. nubimontanus and E. cupidus remain uncertain. E. middelburgensis samples showed no clustering but had poor amplification success. This study demonstrates the suitability of automated ISSR fingerprinting as a method for plant conservation studies, especially in resource-constrained countries, and we make recommendations as to how this methodology can be effectively implemented.

Medical waste management is crucial issues for keeping our life safe and safety. Without effective measures for waste management, we cannot keep ourselves safe from different types of contagious diseases; viruses, bacteria. Knowledge sharing assists healthcare staff in identifying and mitigating hazards on appropriate handling, segregation and disposal medical waste. The aim of the study is to identify a multifaceted analysis of knowledge sharing, training, communication and attitudes for effective medical waste management. This study selected 153 medical workers randomly, including nurses, lab technologists, and cleaners, from hospitals, diagnostic centers, and clinics in the northern part of Bangladesh. The study design of this research is mixed-methods. This research adopts a survey and interview as a research strategy. The samples are collected randomly. SPSS software packages, MS Excel Office, and PLS-SEM are used to analyze data. Most of the respondents always share their knowledge face-to-face according to the findings. The result also shows that there are positive relationship between sources of knowledge (p: 0.046), awareness and knowledge (p: 0.049), attitudes of waste management (p: 0.025) and effective medical waste management. However, there are no relationships between communication and collaboration (p: 0.943), the practice of waste management (p: 0.155), supervision and staff monitoring (p: 0.527), training and education (p: 0.656) and effective medical waste management. Its focus on the northern part of Bangladesh introduces regional specificity, potentially limiting the applicability of results to other regions. The knowledge-sharing practices for waste management among medical staff are examined within this research, along with the relationship between attitude, awareness, and knowledge, staff supervision and monitoring, practice, training, and education and effective medical waste management that have not been studied before home and abroad. This analysis highlights the critical need for an integrated approach to medical waste management, emphasizing the importance of continuous education, open communication, and cultivating a culture that prioritizes environmental sustainability. The insights from this study offer practical recommendations for healthcare institutions to improve their medical waste management practices, ultimately leading to enhanced health outcomes and better environmental protection.

Macular pigment optical density (MPOD) is an important clinical biomarker for ocular conditions like macular degeneration, diabetic eye disease, and digital eye strain. Additionally, its measurements can be essential in health assessment for visual function, systemic diseases, and brain health. We aimed to assess the repeatability, agreement, and effects of the learning curve of the new portable handheld heterochromatic flicker photometer, Zx Pro, in measuring MPOD in a wide age range of ocular-healthy adults, compared to the MPOD measurements obtained using the clinically available QuantifEye device. Seventy-six participants performed one practice at-tempt and two study-related MPOD measurements with the Zx Pro and the QuantifEye. The Pearson correlation between the study-related MPOD measurements for Zx Pro and QuantifEye devices was 90% and 85%, respectively. Altman and Bland plots show excellent agreement between the device's MPOD data, with 95% limits of an agreement being -0.10 to +0.11 du. The mean difference between the practice attempt and the study-related measurements was not statistically significant for Zx Pro but was significant for QuantifEye (Repeated measures ANOVA p=0.325 and p=0.015, respectively). The Zx Pro provides excellent repeatable MPOD measurements, has an insignificant learning curve, and is in good agreement with the predicate device.

The reproductive biology of the invasive blue crab Callinectes sapidus was studied in the Thermaikos Gulf (Northwest Aegean Sea, Eastern Mediterranean). In the two-year survey 5,698 (2,897♂/ 2,801♀) crabs were caught with the use of fyke nets. Total sex ratio (♂/♀) reached equality (1.03:1). The female blue crab exhibited a protracted reproductive period. Mature and ovigerous females exhibit short migratory movements from estuarine and inshore waters, where the population mostly congregates (0-3 m), and move to slightly deeper waters (1-3 m) up to 9 m for spawning. A total of 340 ovigerous females were caught. Their number varied both spatially and temporally; they were observed for a 7-month period (April to October) with a clear peak in July - August and at a 3 m depth gradient corresponding to ≈60% of the total number of ovigerous females caught in both years. Size at first sexual maturity (CW50) was estimated at 113.1 mm CW. Average fecundity was ≈790,000 eggs. Experimental trawling showed that inshore waters (<1 m) in the estuaries serve as nursery areas for juveniles. Defining the spatiotemporal and bathymetrical distribution of ovigerous females in any invaded coastal habitat could be considered key information for the implementation of a management policy for the species.

Cardiovascular diseases (CVD) are the leading cause of morbidity and mortality worldwide, including in Croatia. Since most patients have multiple disorders and diseases caused largely by the same risk factors, and as it is essential to approach each patient as a person with all disorders, today we are talking about a new paradigm - cardio-renal-metabolic (CKM) syndrome and cardio-renal-metabolic health, which necessarily includes brain health. Elevated systolic blood pressure, LDL cholesterol, smoking, obesity, diabetes, impaired renal function or chronic kidney disease, which all stem from insufficient physical activity, unhealthy diet with excessive intake of table salt, and air pollution, are the leading causes of overall morbidity and mortality from CKM diseases, especially mortality from CVD. Experts from various fields key to CKM health have written this document with the aim of integrating it as part of the national plan for the prevention of chronic non-communicable diseases with a focus on CVD, which should become mandatory and be based on the existing guidelines of professional societies.

Barium monofluoride (BaF) is a polar molecule of interest to measurements of the electron electric dipole moment [1, 2]. For this purpose efforts are under way to investigate this molecule embedded within cryogenic matrices, e.g., in solid Ne [3]. For a theoretical understanding of the electronic structure of such an embedded molecule the need arises for efficient methods which are accurate, but also can handle a number of atoms which surround the molecule. The calculation for gas-phase BaF can be reduced to involve only outer electrons by representing the inner core of Ba with a pseudopotential [4] while carrying out a non-relativistic calculation with an appropriate basis set [5]. In this work we demonstrate to which extent this can be achieved using coupled-cluster methods to deal with electron correlation. As a test case the SrF(X 2Σ+ → B 2Σ+) transition is investigated and excellent accuracy is obtained with the EOM-CC3 method. For the BaF(X 2Σ+ → A′ 2∆, X 2Σ+ → A 2Π, X 2Σ+ → B 2Σ+) transitions various coupled-cluster approaches are compared with very good agreement for EOM-CC3 with experimentally derived spectroscopic parameters except for the excitation to the A′ 2∆ state for which the excitation energy is overestimated by 200 cm−1.

Some studies investigated the relationship between frequency domain analysis of heart rate variability and the cognitive performance at the Stroop task. We propose a combined assessment also of trunk mobility in 72 healthy women to investigate the relationship between cognitive, cardiac and motor variables based on a principal component analysis. We also assessed the change on this result after an intervention of two months aiming at improving the perception-action link. At baseline, the PCA correctly identified 3 components: one related to cardiac variables, one to trunk motion and one to the performance of Stroop task. After the intervention, only two components were found with trunk symmetry and range of motion, accuracy and time to complete the Stroop task and low frequency heart rate variability aggregated in a single component by PCA. It suggested that this protocol was effective in investigating the embodied cognition and we defined this approach as “embodimetrics”.

Distributed tracing is a cutting-edge technology for monitoring, managing, and troubleshooting native cloud applications. It offers a more comprehensive and continuous observability, surpassing traditional logging methods, and is indispensable for navigating modern complex software architectures. However, the sheer volume of generated traces is staggering in distributed applications, and direct storage and utilization of every trace are impractical due to associated operational costs. This entails a sampling strategy to select which traces warrant storage and analysis. Historically, sampling methods have included a rate-based approach, often relying heavily on a manual configuration. There is a need for a more intelligent approach, and we propose a hierarchical sampling methodology to address multiple requirements concurrently. Initial rate-based sampling mitigates the overwhelming volume of traces, as no further analysis can be performed on this level. In the next stage, more nuanced analysis is facilitated based on the previous foundation, incorporating information regarding trace properties and ensuring the preservation of vital process details even under extreme conditions. This comprehensive approach not only aids in the visualization and conceptualization of applications but also enables more targeted analysis in later stages. As we delve deeper into the sampling hierarchy, the technique becomes tailored to specific purposes, such as simplifying application troubleshooting. In this context, the sampling strategy prioritizes the retention of erroneous traces from dominant processes, thus facilitating the identification and resolution of underlying issues. The focus of this paper is to reveal the impact of the sampling on troubleshooting efficiency. Leveraging intelligent and explainable artificial intelligence solutions enables the detection of malfunctioning microservices and provides transparent insights into root causes. We advocate for using rule-induction systems, which offer explainability and efficacy in decision-making processes. By integrating advanced sampling techniques with machine learning-driven intelligence, we empower organizations to navigate the complexities of large-scale distributed cloud environments effectively.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The accurate wellbore pressure control not only prevents from lost circulation/blowout and fracturing formation by managing density of drilling fluid, but also improves productivity by mitigating reservoir damage. The geothermal pressure calculated by constant parameters for geothermal well would bring big error easily, as the changes of physical, rheological and thermal properties of drilling fluids with temperature were neglected. This paper researches the wellbore pressure coupling by calculating the temperature distribution with existed model, fitting the rule of density of drilling fluid with temperature and establishing mathematical models to stimulate the wellbore pressures, which is expressed as the variation of Equivalent Circulating Density (ECD) under different conditions. With this method, temperature and ECDs in the wellbore of the first medium-deep geothermal well ZK212 Yangyi Geothermal Field in Tibet were determined, and the sensitivity analysis was simulated by assumed parameters, i.e. circulating time, flow rate, geothermal gradient, diameters of wellbore, rheological models and regimes, the results indicated the geothermal gradient and flow rate were the most influence parameters on the temperature and ECD distribution, and additives added in drilling fluid should be careful which would change the properties of drilling fluid and induce the temperature redistribution. To make sure the safe drilling, velocity of pipes tripping into the hole, depth and diameter of wellbore are considered to control the surge pressure.

We investigate regular damped oscillatory structures appearing in the "effective" form factor of various hadrons. The behavior of this form factor can be extracted from the experimental information on total cross sections, the processes $\sigma_{tot}(e^+e^- \to h \bar h)$, $h=\pi^{\pm}, K^{\pm}, K^0, p, n $ are examined. The apparent oscillations have been observed for the first time for the proton and we show, taking also other hadrons into the consideration, that they are an arbitrary artifact resulting from a very simplistic theoretical description based on an elementary three-parametric model. If the data are described by a more appropriate and well physically funded U\&A model, then the oscillations disappear. In addition, if the simple model is used to describe the data, one observes that the oscillations are opposite for particles which form an isospin dublet. We show, by using the U\&A model, that this feature is explained by the transformation properties of the corresponding states in the isotopic space.

Count data are used in many fields of practice, especially Poisson distribution as a popular choice for the marginal process distribution. If these counts exhibit serial dependence, a popular approach is to use a Poisson INAR(1) model to describe the autocorrelation structure of process. In this paper, the explicit formulas are proposed to evaluate performance characteristics of Double Moving Average control chart (DMA) for Integer valued autoregressive of serial dependence Poisson process. The characteristics of the control chart are frequently measured as Average Run Length (ARL) which means that the average of observations are taken before a system is signaled to be out-of-control. These proposed explicit formulas of ARL are simple and easy to implement for practitioner. The numerical results show that the DMA chart performs better than others when the magnitudes of shift are moderate and large.

This work reports the role of structure and composition on the determination of the performances of p-type SnOx TFTs deposited by rf magnetron sputtering at room temperature, followed by a post-annealed step up to 200 °C at different oxygen partial pressures (Opp), between 0% and 20%, but where the p-type conduction was only observed between 2.8–3.8%. The role of structure and composition were evaluated by XRD and Mössbauer spectroscopic studies. The study allows to identify the best phases/compositions and thicknesses (around 12 nm) to be used that lead to the production of TFTs with a bottom gate configuration, on glasses coated with conductive Indium Tin Oxide, followed by Aluminium Titanium Oxide dielectric layer with saturation mobility of 4.6 cm²V⁻¹s⁻¹ and on-off ratio above 7 × 10⁴, operating at the enhancement mode with a saturation voltage of −10 V.

There is an observed general low performance of Ethiopian Sport Governing Bodies (SGBs) in service delivery. Evidence shows that the trend can be corrected with proper understanding and insight into the process of organisational and management factors of these SGBs. This study aimed to investigate the contribution of organisational and management factors on effective sport service delivery in SGBs. For this study, a cross-sectional research design was employed. Purposive sampling was used to choose 350 samples. Pearson Product Moment Correlation Coefficient and multiple regression were used to analyse the data at the 0.05 significant level. The findings confirmed that organisational and management factor variables had a significant positive relationship with sport service delivery (organisational structure (r=0.515), organisational capabilities (r=0.701), communication (r=0.549), management practice (r=0.571), materials &amp; resources (r=0.527) and stakeholders satisfaction (r=0.742). In addition, Management factors were found to be significant contributors for predicting effective sport service delivery (F(3, 329)= 165.868, R2= 0.612). Furthermore, organisational factors had a joint significant contribution to effective sport service delivery (F(3, 329) = 148.743, R2= 0.576). In addition, organisational and management factor variables jointly best predicted effective sport service delivery in Ethiopian SGBs (F(6, 326) =130.81, R2= 0.707). Therefore, this study suggests organisational and management factor variables can be used to predict effective sport service delivery.

Programmed death ligand 1 (PD-L1) is a co-inhibitory molecule expressed on the surface of various cell types, known for its suppressive effect on T cells through interaction with PD-1. Neutrophils also express PD-L1, and its expression is elevated in specific situations; however, the immunobiological role of PD-L1+ neutrophil has not been fully characterized. Here, we report that PD-L1-expressing neutrophils increased in methicillin-resistant Staphylococcus aureus (MRSA) infection are highly functional in bacterial elimination and supporting inflammatory resolution. The frequency of PD-L1+ neutrophils was dramatically increased in MRSA-infected mice, and this population exhibited enhanced activity in bacterial elimination compared to PD-L1- neutrophils. An administration of PD-L1 monoclonal antibody did not impair PD-L1+ neutrophil function suggesting that PD-L1 expression itself does not influence neutrophil activity. However, PD-1/PD-L1 blockade significantly delayed liver inflammation resolution in MRSA-infected mice, as indicated by increased plasma alanine transaminase (ALT) level and frequencies of inflammatory leukocytes in the liver implying that neutrophil PD-L1 suppresses the inflammatory response of these cells during the acute phase of MRSA infection. Our results reveal that elevated PD-L1 expression can be a marker for enhanced anti-bacterial function of neutrophils. Moreover, PD-L1+ neutrophils are an indispensable population attenuating inflammatory leukocyte activities assisting in a smooth transition into the resolution phase in MRSA infection.

Vaccine hesitancy has emerged as a significant barrier to achieving herd immunity and protecting populations from preventable diseases. Despite the proven effectiveness and safety of vaccines, many individuals remain hesitant or refuse to vaccinate themselves or their children. This review aims to identify the factors contributing to vaccine hesitancy, including misinformation, lack of trust in authorities, cultural beliefs, and access barriers. We also discuss the impact of vaccine hesitancy on public health, including outbreaks of vaccine-preventable diseases and erosion of trust in public health authorities. Furthermore, we present evidence-based communication strategies for addressing vaccine hesitancy, including building trust, providing accurate information, addressing myths and misconceptions, engaging with local influencers, and utilizing social media and digital platforms. By understanding the factors contributing to vaccine hesitancy and implementing effective communication strategies, healthcare providers, public health officials, and community leaders can work towards promoting widespread vaccine acceptance and protecting public health.

Elastic peak electron spectroscopy, abbreviated EPES, involves ana- lyzing the line shape found in the elastic peak. The reduction in the energy of electrons of the elastic peak is a result of energy transfer to the target atoms, a phenomenon known as recoil energy. EPES differs from other electron spectroscopies in its unique ability to identify hydrogen in polymers and hydrogenated carbon-based materials. This feature is particularly noteworthy because lighter elements exhibit stronger energy shifts. The energy difference between the positions of the elastic peak of carbon and the elastic peak of hydrogen tends to increase as the kinetic energy of the incident electrons increases. If, during electron irradiation of an insulating polymer, the number of secondary electrons emitted by the surface is less than the number of electrons absorbed in the sample, the surface floats energetically until it stabilizes at a potential energy eVs. As a result, the interaction energy changes and modifies the energy difference between the elastic peaks of hydrogen and carbon. In this study, the charge effects are evaluated using the Monte Carlo method to simulate the EPES spectra of electrons interacting with polystyrene and polyethylene.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

Starting from unidentified objects moving inside a two-dimensional Euclidean manifold, we propose a simple method to detect the topological changes that occur during their reciprocal interactions and shape morphing. This method, which allows the detection of topological holes development and disappearance, makes it possible to solve the uncertainty due to disconnectedness, lack of information and absence of objects’ sharp boundaries, i.e., the three troubling issues which prevent scientists to select the required proper sets/subsets during their experimental assessment of natural and artificial dynamical phenomena, such as fire propagation, wireless sensor networks, migration flows, neural networks’ and cosmic bodies’ analysis.

The use of tuning forks to measure fluid density and viscosity is widely employed in fields such as food, medicine, textiles, automobiles, petrochemicals, and deep drilling. The explicit analytical model based on Euler-Bernoulli cantilever beam theory for the relationship between tuning fork resonance characteristics and the density and viscosity of fluid is only applicable to the situation where the fluid viscous effect is very small. In this paper, the finite element method is used to simulate the influence of large variations in fluid density and viscosity on the resonance characteristic parameters (resonant frequency and quality factor) of the tuning fork. The numerical simulation results are compared with the analytical analysis results and experimental measurement results. Then, the sensitivity of tuning fork resonance characteristic parameters to fluid density and viscosity is studied. The results show that compared with the analytical results, the numerical simulation results have a higher degree of agreement with the experimental measurement results. The relative difference in resonant frequency is less than 2%, and the relative difference in quality factor is less than 4%. This indicates that the finite element method includes the influence of fluid viscosity on tuning fork resonance parameters, which is more in line with the actual conditions than the analytical model. Simulating and analyzing the sensitivity of the tuning fork to fluid density and viscosity by the finite element method, it is possible to consider the situation where fluid density and viscosity vary over a large range. Compared with experimental measurements, this method has higher efficiency and can significantly save time and economic costs. This study can overcome the limitation of existing explicit analytical models, which are only applicable when the viscous effects of the fluid are very small. It enables a more accurate simulation of the coupling vibration between tuning forks and fluids, thereby providing theoretical references for further optimizing tuning fork structural parameters to enhance the accuracy of measuring fluid characteristic parameters.

Background: The transversus abdominis plane (TAP) block has gained increasing importance as a very effective pain relief in for caesarean section. This study aimed to compare bupivacaine (Group B), bupivacaine with dexmedetomidine (Group BD) and bupivacaine with dexamethasone (Group BDx) applied in ultrasound-guided TAP block in the treatment of CS postoperative pain. Material and Method: American Society of Anesthesiologists I and II pregnant women who underwent cesarean section were included in the study. Forty patients were admitted in each group. All patients were applied TAP block with ultrasound guidance by administering the medications of the group in which they were included. Results: Body mass index (BMI) and operation duration were higher in Group B (p*=0.01 and 0.004, respectively). Instant tramadol requirement and amount were higher in Group B at some of follow up times. Patient satisfaction scale were better in Group BD and Group BDx. Conclusion: TAP block significantly reduces pain after cesarean section, prolongs the time to first analgesic request, and reduces the need for additional opioid analgesics. The addition of adjuvant to the TAP block usually improves the postoperative clinical condition. However, some special conditions such as body mass index (BMI) may negatively affect the clinical situation. Comprehensive, standardized, randomized controlled studies are needed to compare results under different conditions.

In the weak-field approximation of covariant theory of gravitation the problem of 4/3 is formulated for internal and external gravitational fields of a body in the form of a ball. The dependence of the energy and the mass of the moving substance on the energy of field accompanying the substance, as well as the dependence on the characteristic size of the volume occupied by the substance are described. Additives in the energy and the momentum of the body, defined by energy and momentum of the gravitational and electromagnetic fields associated with the body are explicitly calculated. The conclusion is made that the energy and the mass of the body can be described by the energy of ordinary and strong gravitation, and through the energies of electromagnetic fields of particles that compose the body.

Unmanned aerial vehicles (UAVs), commonly known as drones, present a cost-effective solution for the swift collection of data from vast and remote areas that are otherwise difficult to access. The Mediterranean Basin, known for being a hot spot for plant biodiversity, hosts several habitats and taxa of significant naturalistic value. However, many of these areas are often inaccessible to botanists, making exploration and research challenging. The aim of this paper is to involve the utilization of drone surveys and open-source software for botanical research. Our primary goal is to show the effectiveness of these tools in the field and demonstrate their practical application in Natura 2000 sites. The protected area chosen for this research is Rocca di Novara, situated in northeastern Sicily. Thanks to our drone investigations, we were able to capture images of the mountain’s side that is inaccessible to humans. This allowed us to observe the habitat of some species in detail. One of the most fascinating discoveries was the reappearance of Saxifraga callosa subsp. australis, which had not been confirmed in this area for over 140 years. Using drones for botanical research can boost field research, making monitoring easier and more cost-effective over time, especially in Natura 2000 sites.

With the deterioration of the bridge performance and ever-increasing amount of traffic, the bridge safety is becoming a concern for engineering community. A method that can assess the bridge's condition in real-time is urgently needed. The main factors that hinder the bridge condition assessment are the uncertain operational environments. A new moving principal component analysis (MPCA) based method is developed for structural damage detection of bridges in operational environments in this paper. Two main operational environmental factors: the environmental temperature and traffic loads, are studied in the assessment process to verify the robustness and practicality of the proposed method. The numerical and experimental results show that the proposed method is effective and accurate to assess the bridge condition in operational environments.

Supplier collaboration and partnership in procurement are essential elements for enhancing organizational efficiency, innovation, and resilience in today's globalized markets. This qualitative study investigates the dynamics of effective supplier relationships, focusing on trust, communication, innovation, quality, cost savings, and resilience as critical factors. Data were gathered through semi-structured interviews, case studies, and document analysis across diverse industries, highlighting insights from procurement professionals and supplier representatives. Key findings underscore the foundational role of trust and communication in fostering successful collaborations. Establishing transparent, ongoing communication channels facilitates mutual understanding, reduces conflicts, and enhances overall satisfaction. Collaborative innovation emerged as pivotal, enabling organizations to pool resources and expertise for product development and process improvement. Quality and reliability were identified as significant outcomes of close partnerships, particularly in industries with stringent standards such as aerospace and healthcare. Furthermore, the study reveals substantial cost savings and efficiency gains through collaborative efforts in process optimization and waste reduction. Effective risk management practices within these partnerships enhance supply chain resilience, enabling organizations to anticipate and mitigate disruptions proactively. Despite these benefits, challenges such as cultural differences, technological integration, and regulatory compliance require strategic mitigation strategies. In conclusion, organizations can optimize supplier collaborations by prioritizing trust-building, fostering a culture of innovation, and investing in robust relationship management practices. This approach not only enhances operational performance but also positions organizations to navigate market uncertainties and achieve sustainable growth in a competitive landscape.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

True contact between solids with randomly rough surfaces tends to occur at a large number of microscopic contact patches. So far, two scaling regimes have been identified for the number density n(A) of contact-patch sizes A in elastic, non-adhesive, self-affine contacts. At small A, n(A) is approximately constant, while n(A) decreases as a power law at large A. Using Green’s function molecular dynamics, we identify a characteristic (maximum) contact area Ac above which a superexponential decay of n(A) becomes apparent if the contact pressure is below the pressure p_cp at which contact percolates. We also find that A_c increases with load relatively slowly far away from contact percolation. Results for A_c can be estimated from the stress autocorrelation function G_σσ (r) with the following argument: the radius of characteristic contact patches, r_c, cannot be so large that G_σσ (r_c) is much less than p_c². Our findings provide a possible mechanism for the breakdown of the proportionality between friction and wear with load at large contact pressures and/or for surfaces with a large roll-off wavelength.

This paper presents an extension for principles of Differential Geometry on Surfaces (re-hashed through the budding field of CMS, the Calculus of Moving Surfaces). It analyzes mostly 2D Hypersurfaces with Riemannian Geometry and proposes the construction of a 3D Static Frame combining the Surface Basis Vectors with the Orthogonal Normal Field as a 3D Orthogonal Vector Frame. The paper introduces conventions for manipulating Tensors defined using this 3D Orthogonal Vector Frame as well as Curvature Connections associated with this Vector Frame. It then finally introduces Symbols and Tensors to describe Inner Products and Variance within the 3D Vector Frame and then extends all the above concepts to a surface which is Dynamic utilizing principles from CMS. This formulation has potential to extend identities and concepts from CMS and from Differential Geometry in a compact Tensorial Framework, which agrees with the new Framework proposed by CMS.

The description of the electron-electron interactions in two-dimensional materials has a dimensional mismatch, where electrons live in (2+1)D while photons propagate in (3+1)D. In order to define an action in (2+1)D, one may perform a dimensional reduction of quantum electrodynamics in (3+1)D (QED4) into Pseudo quantum electrodynamics (PQED). The main difference between this model and QED4 is the presence of a pseudo-differential operator in the Maxwell term. However, besides the Coulomb repulsion, electrons in a material are subjected to several microscopic interactions, which are inherent in a many-body system. These are expected to reduce the range of the Coulomb potential, leading to a short-range interaction. Here, we consider the coupling to a scalar field in PQED for explaining such mechanism, which resembles the spontanoues symmetry breaking (SSB) in Abelian gauge theories. In order to do so, we consider two cases: (i) By coupling the gauge field to a Higgs field in scalar quantum electrodynamics in (3+1)D and, thereafter, performing the dimensional reduction and; (ii) By coupling a Higgs field to the gauge field in PQED and subsequently calculating its effective potential. In case (i), we obtain a model describing electrons interacting through the Yukawa potential and, in case (ii), we show that SSB does not occur at one-loop approximation. The relevance of the model for describing electronic interactions in two-dimensional materials is also adressed.

This article introduces an analytical framework that interprets individual measures of entropy-based mobility derived from mobile phone data. We explore and analyze two widely recognized entropy metrics: random entropy and uncorrelated Shannon entropy. These metrics are estimated through collective variables of human mobility, including movement trends and population density. By employing a collisional model, we establish statistical relationships between entropy measures and mobility variables. Furthermore, our research addresses three primary objectives: firstly, validating the model; secondly, exploring correlations between aggregated mobility and entropy measures in comparison to five economic indicators; and finally, demonstrating the utility of entropy measures. Specifically, we provide an effective population density estimate that offers a more realistic understanding of social interactions. This estimation takes into account both movement regularities and intensity, utilizing real-time data analysis conducted during the peak period of the Covid-19 pandemic.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

MP2/aug-cc-pVTZ calculations were carried out for the ZFH₃-B complexes (Z = C, Si, Ge, Sn and Pb; B = C₂H₂, C₂H₄, C₆H₆ and C₅H₅^-; relativistic effects were taken into account for Ge, Sn and Pb elements). These calculations are supported by other approaches; the decomposition of the energy of interaction, Quantum Theory of Atoms in Molecules (QTAIM) and Natural Bond Orbital (NBO) method. The results show that tetrel bonds with π-electrons as Lewis bases are classified as Z…C links between single centers (C is an atom of the π-electron system) or as Z…π interactions where F-Z bond is directed to the mid-point (or nearly so) of the CC bond of the Lewis base. The analogues systems with Z…C/π interactions were found in the Cambridge Structural Database (CSD). It was found that the strength of interaction increases with the increase of the atomic number of the tetrel element and that for heavier tetrel elements the ZFH₃ tetrahedral structure is more deformed towards the structure with the planar ZH₃ fragment. The results of calculations show that the tetrel bond is sometimes accompanied by the Z-H…C hydrogen bond or even sometimes the ZFH₃-B complexes are linked only by the hydrogen bond interaction.

VE is a powerful technique for analyzing a design with a focus on functionality, reducing costs, and increasing value. However, in order to proceed with the design of VE, the theoretical basis for the VE target selection process, which must be preceded in the preparation stage, is lacking, and as a result, it is difficult to verify the most effective target selection. Thus, a theoretical basis is needed. In this study, we intend to quantify the WORTH value of the COST TO WORTH technique and present an objective model of the target selection method using the derived Value Index (VI). For this purpose, cost worth (WORTHC) was calculated based on the performance data of 1,008 cases of 15 building types provided by the Domestic Public Procurement Service and the share of 83 detailed processes in 7 fields. Then, a survey was conducted targeting the ordering companies, and the final worth (WORTHF) was calculated by multiplying the derived customer value (WORTHV ) weight for each detailed work type. We calculated the Value Index (VI) by comparing COST and WORTHF for each detailed construction type of the VE project and developed a model to select construction types that exceed the VI standard value derived using the standard error of the population. Both cost experts and non-cost experts can use the developed model to specify the VE target selection criteria in order to easily select the key target, objectively sort the values that serve as the basis for calculating the value index and make it possible to more easily select the VE target selection criteria based on theoretical evidence. Also, the model can be used to obtain effective detailed design VE results.