In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

This study aims to evaluate the patient’s dose exposure from Computed Tomography Pulmonary Angiography (CTPA) examination and to estimates the cancer risk induced from the examinations based on the patient’s size. One hundred patients were recruited, and data information was collected retrospectively. A multi-detector (MDCT) (Philips Brilliance 128, USA) scanner were utilized for the CTPA examination, and dose data were obtained from the system. The effective diameter of each subjects’ image was measured for the Size-specific dose estimates (SSDEs). All subjects divided into Group 1 (19 – 25 cm), Group 2 (25-28 cm) and Group 3 (28-38 cm), where the association between gender were analysed. Effective dose (E), SSDE, organ dose and cancer risk of each group were evaluated and compared statistically using independent t-test and one-way ANOVA. The range of mean CTDI_vol, DLP and E values were (6.44 – 17.42 mGy), (239 – 631 mGy), (5.19 – 13.90 mSv), respectively. In respective with the patient’s effective diameter, the mean SSDE value for Group 1, Group 2 and Group 3 were 9.93 ± 3.89 mGy, 13.70 ± 9.04 mGy and 22.29 ± 7.35 mGy. The organ dose and cancer risk attained for breast, lung and liver were 17.05 ± 10.40 mGy (194 per one million procedure), 17.55 ± 10.86 mGy (192 per one million procedure) and 15.04 ± 9.75 mGy (53 per one million procedure), respectively. Lung and breast with more massive patient’s effective diameter received the highest dose exposure which increases the probability of the cancer risk. CTDI_vol was found to be underestimated, and SSDE provides more accurate in describing the radiation dose and cancer risk. Body effective diameter found to be significant on the estimation except for gender. Therefore, it is essential to apply optimised protocols in order to reduce patient’s exposure during CTPA examination.

Tungsten balls with sub-100-μm diameter can function as probe tips for micro-coordinate measuring machines (CMMs) to measure ultraprecise workpieces such as ceramic bearings with a high aspect ratio. A high-precision measuring system was proposed to evaluate the roundness error of the self-made tungsten ball tips. The principles and mathematical models of the measuring system are illustrated, and the fabrication principle of tungsten balls is introduced. An analysis was conducted on the maximum allowable contact force and bending strength of the tungsten ball tips, and the elastic mechanism was designed based on the analysis. A ruby probe with a sphericity error of 130 nm (A-5003-0577, Renishaw Corporation) used as a reference sphere was measured to verify the system's effectiveness. Repeated measurement experiments were performed for two tungsten ball tips. The results show the roundness error of the tungsten ball-A is between 568.3 and 586.2 nm with a standard deviation of 6.6 nm while the tungsten ball-B’s roundness error is between 898.5 and 958.0 nm with a standard deviation of 19.7 nm. The uncertainty is calculated as 125.8 nm. The developed system can stably measure the roundness of the tungsten ball tips.

The nozzle is the key element of the water jet generator for energy conversion. In order to explore the influence of the nozzle diameter on the pressure characteristics of the supercharged pulsed water jet plenum chamber, a supercharged pulsed water jet pressure acquisition system was established, and the Equations of motion and theoretical pressurization ratio equations of the supercharged pulsed water jet generator were established. The pressurization chamber pressure acquisition experiments under different nozzle diameters were carried out. The research results indicate that there is a critical nozzle diameter. When the nozzle diameter is less than the critical diameter, the pressure in the boost chamber is equal to the product of the driving pressure and boost ratio. As the nozzle changes, there is no significant change in the peak pressure and frequency of the boost chamber; When the nozzle diameter is greater than the critical diameter, there is a non-linear relationship between the boost chamber pressure and the driving pressure. As the nozzle diameter gradually increases, the actual boost ratio gradually decreases, and the peak pressure of the boost chamber further decreases. The nozzle diameter can no longer provide a load for the establishment of fluid pressure in the boost chamber. The research results provide a research basis for further controlling the pressure characteristics of the boost pulse water jet.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

Aim: To analysis the relationship between healthy adults right ventricular diameter (RVD) and geographical factors. Location: China’s 22 provinces, municipalities and autonomous regions. Methods: Using correlation analysis the relationship between RVD and nine geographic factors, build predictive models by factor analysis. Results: There is significant correlation between RVD and geographical factors, and the annual average temperature is most relevant geographical factors, a predictive model was built by factor analysis: Ŷ = 19.46 + 0.0007072X1 + 0.001034X2 -0.05412X3 -0.001405X4 -0.0006351X5 + 0.02903X6 + 0.01243X7 -0.01033X8 + 0.03816X9 ± 0.63. Then using Kriging interpolation interpolate the geographical distribution of Chinese healthy adult right ventricular diameter reference value in ArcGIS software. Main Conclusion: If geographic factors can be derived in anywhere of China, RVD can be calculated by the model, you can also get RVD from geographical distribution.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

This study uses machine learning to identify key factors influencing the cost-effectiveness of over-the-counter (OTC) medications. By developing a novel cost-effectiveness rating (CER) from user ratings and prices, we analyzed data from Amazon. The findings indicate that FSA/HSA eligibility, symptom treatment range, safety warnings, special effects, active ingredients, and packaging size significantly impact cost-effectiveness across cold, allergy, digestion, and pain relief medications. Medications eligible for FSA or HSA funds, treating a broader range of symptoms, and having smaller packaging are perceived as more cost-effective. Cold medicines with safety warnings were found to be cost-effective due to their lower average price and effective ingredients like phenylephrine and acetaminophen. Allergy medications with kid-friendly features showed higher cost-effectiveness, and ingredients like calcium, famotidine, and magnesium boosted the cost-effectiveness of digestion medicines. These insights help consumers make informed purchasing decisions and assist manufacturers and retailers in enhancing product competitiveness. Overall, this research supports better decision-making in the pharmaceutical industry by highlighting factors that drive cost-effective medication purchases.

While lidar-based forest inventory methods have been widely demonstrated, prediction of tree diameters with lidar is not well understood. The performance metrics typically used in studies for prediction of diameters can be difficult to interpret and may not support comparative inferences between sampling designs or study areas. We evaluate a variety of lidar and k nearest neighbor (k-NN) strategies for prediction of tree diameter distributions using two indices which are easier to interpret and compare. The indices are based on the coefficient of determination (R²), and root mean square deviation (RMSD). These indices facilitate comparisons with alternative (non-lidar) inventory strategies, and with other project areas. We evaluate k nearest neighbors (k-NN) dbh density (relative frequency by dbh class) prediction strategies with lidar for 190 training plots distribute across the 800 km² Savannah River Site in South Carolina, USA. We evaluate the performance of k-NN with respect to distance metrics, number of neighbors, predictor sets, and response sets. Amongst the examined strategies we found Mahalanobis distance with k = 3 neighbors performed best according to a number of criteria.

Adenomyosis, a benign gynecological condition characterized by the infiltration of endometrial tissue into the myometrium, poses significant challenges to women's reproductive health. Recently, the landscape of adenomyosis diagnosis transformed significantly, thanks to advancements in imaging technologies such as transvaginal ultrasound and magnetic resonance imaging. This lead to a noticeable shift in the demographic profile of patients diagnosed with adenomyosis, including younger women of reproductive age who frequently present with a diverse array of symptoms. Approximately 20% of women are affected by adenomyosis. Adenomyosis manifests with various subtypes, distinct epidemiological profiles, symptomatology, and treatment responses, necessitating tailored approaches for optimal management. Despite its clinical significance, adenomyosis remains understudied, resulting in a significant disparity in research and literature compared to other gynecological conditions. The severity of adenomyosis is compounded when coexisting with endometriosis, particularly deep infiltrating endometriosis (DIE), leading to exacerbated fertility issues and severe symptomatology. The wide range of symptoms, including adverse pregnancy outcomes such as pre-eclampsia, highlights its wider impact and emphasizes the need for increased awareness of the condition. Furthermore, Adenomyosis is frequently associated with treatment failure in endometriosis, contributing to dienogest resistance, elevated discontinuation rates, and persistent pain post endometriosis surgery. Additionally, the lack of specific treatments tailored to adenomyosis poses a considerable challenge in clinical management.

The loop and knot securities of 2 braided and 2 monofilament sutures of four diameters (3.0, 2.0, 0, 1) were evaluated with a tensiometer for four 4-throw knots known to be secure with a 2.0 polyfilament suture. Loop security of monocryl 1 is low, being 14.7 + 3.0 Newton (N) for a 3-throw half-knot (H3) and 15.4 + 2.4 N and 28.3+ 10 N for 2 (SSs) and 4-throw (SSsSsSs) symmetrical sliding half-hitches. This is lower than 18, 24, and 46 N for similar knots with vicryl. Polyfilament sutures have excellent knot security for all diameters. Occasionally, some slide to open with slightly lower knot security, especially for larger diameters, although not clinically problematic. Knot se-curity of monofilament sutures was unpredictable for all 4 knots, especially for larger diameters, resulting in many clinically insecure knots. A secure monofilament knot requires a 6-throw knot with 2 symmetrical sliding half-hitches or 2 symmetrical half-knots secured with 4 asymmetric blocking half-hitches. In conclusion, with polyfilament sutures, 4 or 5-throw half-knot or half-hitch sequences result in secure knots. For monofilament sutures, loop and knot security is much less, half-knot combinations should be avoided, and secure knots require 6-throw knots with 4 asym-metric half hitches. This conclusion is valid for gynecologic laparoscopic and open surgery, and for surgery in general.

In strawberry production, the combination of high productive performance and fruits with desirable physicochemical characteristics requires the use of plants of good quality and high initial vigor. This study aimed to evaluate the effect of plants with different crown diameters on the productive performance and fruit quality of strawberry plants of the cultivar 'Pircinque.' The study was conducted in two evaluation cycles (2016/2017 and 2017/2018). The experimental design was in randomized blocks, with four repetitions, and plots consisting of 20 plants. This study evaluated the crown diameters of plants of 5, 7, 9, 11, 13, 15, 17, and 19 mm. The productivity and number of fruit values increased significantly with larger caliber plants, which also provided precocity of productivity. The use of more vigorous plants also favored the production of fruits with higher soluble solids / titratable acidity ratios and with epidermis coloration closer to intense red. For the cultivar 'Pircinque', the plant crown diameters between 15 and 17 mm are the most favorable because they condition the best productive performances in combination with precocity and good fruit quality.

Aortic rupture is known as one of the potential causes of sudden cardiac death in athletes. Nevertheless, adaptation strategies for aortic root dilation in athletes vary. The purpose of this study was to investigate aortic root adaptation to physical workload and to determine if aortic root’s and left ventricle sizes are contingent upon the physical workload. Echocardiography was applied to 151 subjects to measure the aortic root at aortic valve annulus (AA) and at sinus of Valsalva (VS). 122 were athletes (41 females and 81 males) and 29 were non-athletes (14 females and 15 males). Of the 41 female athletes, 32 were endurance athletes, and 9 strength athletes. From 81 male athletes, 56 were endurance athletes, and 25 were strength athletes. AA and VS mean values for the body surface area were presented as rAA and rVS. Left ventricle (LV) meaures incuded LV end-diastolic diameter (LVEDD), interventricular septum thickness in diastole (IVSTd), LV posterior wall thickness in diastole (LVPWTd), LV mass (LVM), LV mass index, LV end-diastolic diameter index (LVEDDI). Results indicated that VS was higher in female athletes (28.9±2.36mm) than in non-athletes (27.19±2.87mm, p=0.03). On the other hand, rAA was higher in strength athletes (12.19±1.48mm/m2) than in endurance athletes (11.12±0.99mm/m2, p=0.04). Additionally, rVS and rAA were higher in female strength athletes (17.19±1.78mm/m2, 12.19±1.48mm/m2) than female basketball players (15.49±1.08mm/m2, p=0.03, 10.75±1.06 mm/m2, p=0.02). Statistically significant positive moderate correlations were found between VS and LVEDD, LVM, IVSTd, LVPWTd, rVS and LVEDDI parameters in all athletes. The diameter of Valsalva sinus was greater in female athletes compared to non-athletes. The rAA mean value for body surface area was greater in female athletes practising strength sports as compared to their counterparts who were practising endurance sports. The diameter of the aortic root at sinuses positively correlated with the LV size in all athletes. Trial was registered at ClinicalTrials.gov Identifier: NCT03656861, September 3, 2018 (retrospectively registered).

The current treatment for cervico-facial cancer involves radio and/or chemotherapy. Unfortunately, cancer therapies can lead to local and systemic complications such as mucositis, which is the most common dose-dependent complication in the oral cavity and gastrointestinal tract. Mucositis can cause a considerably reduced quality of life in cancer patients already suffering from physical and psychological exhaustion. However, melatonin, whose role in the treatment of mucositis has recently been investigated, offers an effective alternative therapy in the prevention and/or management of radio and/or chemotherapy-induced mucositis. This review focuses on the pathobiology and management of mucositis in order to improve the quality of cancer patients’ lives.

Partial Differential Equations (PDEs) constitute a fundamental framework for modeling various physical phenomena across diverse fields such as physics, engineering, and finance. Solving PDEs accurately and efficiently remains a significant challenge, particularly when dealing with complex systems or high-dimensional data. In this paper, we present a novel approach based on deep learning techniques to investigate the effective factors in solving PDEs. Our methodology leverages the expressive power of deep neural networks to learn and represent the underlying relationships between input parameters and the solutions of PDEs. By incorporating domain knowledge into the network architecture and training process, our approach aims to provide insights into the key factors influencing the solution of PDEs. We demonstrate the effectiveness of our method through numerical experiments on various PDEs, showcasing its capability to identify important features and improve predictive accuracy. Our findings suggest that deep learning techniques offer a promising avenue for understanding and analyzing the complex dynamics inherent in PDEs, paving the way for enhanced computational methods in scientific and engineering applications.

This study is based on the clamor of fish farmers for a cheaper fish feed alternative to current commercial feeds. At present, 70-80% of aquaculture costs come from feed cost, keeping farmers' income below their expectation. This study aimed to find alternative feeds or supplementary feeds that can perform similarly to the existing commercial feeds thereby reducing farmer expense and cutting down their cost of production and increasing their profitability. To do that, various indigenous raw materials were selected based on an earlier study which could result in a better feed alternative. The formulations for the study included four grow-out treatments mainly: control (commercial feed), taro+control (powdered Colocasia esculenta+commercial fish feed), bloodmeal (formulated fish feed based on bloodmeal), banana stem+control (chopped banana stem+commercial fish feed). A total of 12,000 fingerlings initially weighing 16 g (TL=10 cm) individually were assigned randomly to the four treatments (3000 in each cage measuring 6 x 6 m). Week zero was used for acclimation period, and fingerlings were fed with commercial fish feed. Then the first week used the treatment diets which were adjusted based on average body weight and sampled weekly (ABW=23g; TL=11 cm). The result of the study first showed significant differences between treatments on their fourth week in terms of the diet treatments (MS=0.103, df=3, F=4.12, P=0.0076) with the control and the taro+control showing no difference in terms of weight and length (TC vs CF; P=0.4524). But during the fifth week, the bloodmeal treatment showed increased weight and length for fish sampled (MS=0.109, df=3, F=4.10, P=0.0076) and provided similar weight and length as those from the taro+control and the control (TC vs CF; P=0.3721 and BM vs CF; P=0.0587). During the succeeding weeks, there were no significant differences between feed treatments from 6th weeks onwards, whether with weight [MS=0.130, df=3, F=1.14, P=0.333] or total length of the treatments [MS=0.008, df=3, F=0.40, P=0.75]. The FCR ratio showed taro (1.81) as lowest, followed by blood meal (2.09), and control (2.24) and then banana stem (2.84). In terms of weight gain, fish from the bloodmeal treatment gained the highest (236.97 g), followed by control (223.33 g), then taro (217.67 g) and banana stem (196.99 g). As a result, we find that the tested treatments such as bloodmeal formulated feed, taro+commercial feed, and banana stem+commercial feed can serve as an alternative to purely commercial fish feeds. Cost-benefit analysis showed that a better gross profit margin of 42% and cost-benefit ratio of 1.37 was observed in taro+commercial feed diet.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

BackgroundLiving donor liver transplantation offers comparable long-term results to cadaveric donor transplantation. This study analyzes the selection process of living liver donors at a Western transplant center that utilizes both donation forms. MethodsThis retrospective analysis examined potential living donors, collecting medical data and reasons for refusal, and divided patients by indication and urgency for transplantation. ResultsFrom January 2013 to December 2023, 594 potential living donors were assessed at Jena University Hospital. Of these, 124 living donor transplants were performed. During outpatient evaluation, 357 potential donors were excluded. Subsequently, 238 individuals underwent inpatient assessment, with 100 more being excluded. Main reasons for donor refusal included medical or psychological issues (n=160), disease progression in recipients (n=90), and recipient refusal or donor withdrawal (n=54). The evaluation process showed a trend towards considering more distant relatives and acquaintances as donor candidates with increasing severity of the recipient's disease.

Histone changes that are adjustable and transmitted without altering the DNA sequence are part of epigenetic control. In many disorders, most famously malignancy, abnormal genetic information is seen as a result of mismanagement of typical epigenetic mechanisms. A paradigm change in the diagnosis and treatment of cancer has been brought about by recent discoveries about the processes of epigenetic modifications, chromatin remodeling, and noncoding RNAs implicated in the changed expression patterns of tumor cells. There is a significant increase in the search for drugs that could alter the epigenetic environment altered by tumor cells and benefit from their therapeutic potential. Phytochemicals with a high concentration of naturally produced phenol molecules known as flavonoids can regulate genomic processes. Understanding the precise epigenetic alterations brought on by flavonoid-mediated mechanisms is necessary to develop combination therapy techniques and genomic therapies for cancer. This article aims to thoroughly examine the epigenetic modifications of flavonoids, including their anticancer properties.

Background: The two-stage technique combining the Endoscopic Retrograde CholangioPancreatography (ERCP) with common bile duct (CBD) clearance carried out before the laparoscopic cholecystectomy represents the most common approach for CBD stones. Over time, different techniques have been proposed to manage cholecysto- choledocholithiasis (CCL) advantageously in one stage. Among these, the laparoendoscopic rendez-vous (LERV) addresses the CCL issue with a laparoscopic cholecystectomy with insertion of a guide wire performed at initial stage of the procedure, followed by the clearance of the bile duct carried out by the endoscopists. The goal of this study was to evaluate the efficacy and safeness of LERV procedure recording results and complications, also making a comparison between our results and current literature. Methods: We reviewed our experience of all consecutive patients with cholecysto-choledocholithiasis managed with LERV between January 2018 and December 2023. LERV success rate, operative time, length of hospital stay, stone recurrence, incidence of endoscopic and surgical complications were analysed. Results: A total of 120 patients underwent LERV in our facilities. We reported a 97% LERV success rate, 1.6% conversion-to-open rate, a median intraoperative time of 122 (range 95-220) min. The median hospital stay was 4 (range 2-38) days. An overall morbidity of 15% was reported (18/120): 15 Clavien-Dindo type 1/2, 2 type 3a and one type 3b. In two cases a re-operation during the hospital stay was necessary. At a median follow-up of 14 months (3-59) five patients experienced stone recurrence requiring redo-ERCP in two cases. Conclusion: LERV offers the significant advantage of a single stage procedure and hospitalisation along with a lower risk of post-ERCP pancreatitis, failed CBD cannulation and complications. Our experience confirms safety and effectiveness of the technique for CCL management.

Vitamin A, or retinol, is one of the most effective anti-ageing molecules, but it presents issues with photo-sensitivity and irritation. Retinol-like alternatives are emerging, but have so far been less effective. Here, we present a Silibum marianum extract (SME) as a retinol-like ingredient providing both safety and efficacy. SME was compared to the reference compound, retinol, and to the main alternative, bakuchiol. In ex vivo tests, skin explants from a 58-year-old donor were treated with pure retinol (0.1%), bakuchiol (0.2%) or SME (0.8%). After 5 days, collagen and hyaluronic acid levels were analysed. A placebo-controlled study involving 57 volunteers (ages 45-73 years) was also conducted, with products applied twice-daily for 56 days. Results were measured by AEVA-HE and VISA. Levels of collagen III were significantly increased by SME, by 23% and 16% compared to bakuchiol and retinol, respectively. Compared to bakuchiol, SME treatment increased hyaluronic acid production by 36%. In clinical tests, SME had a significantly stronger anti-wrinkle effect than bakuchiol – reducing the number of wrinkles on the forehead by 21%, and their circumference by 17% – producing effects similar to retinol, and better than bakuchiol. In the self-assessment, 43% of volunteers reported discomfort while using retinol, as compared to 0% for the SME formulation. By enhancing levels of collagen III – the youth collagen – and hyaluronic acid in the skin, SME paves the way for the maturation of collagen I fibrils and skin plumping. With its stronger efficacy compared to bakuchiol and enhanced safety profile compared to retinol, SME may be the next-generation of natural alternatives to retinoids.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

This paper deals with the characteristics of the cyclone separator from the Lagrangian perspective to design important dependent variables, develops a neural network model for predicting the separation performance parameter, and compares the predictive performance between the traditional surrogate model and the neural network model. In order to design the important parameters of the cyclone separator based on the particle separation theory, the force acting until the particles are separated was calculated using the Lagrangian-based CFD methodology. As a result, it was proved that the centrifugal force and drag acting on the critical diameter having a separation efficiency of 50% were similar, and the particle separation phenomenon in the cyclone occurred from the critical diameter, and it was set as an important dependent variable. For developing a critical diameter prediction model based on machine learning and multiple regression methods, Unsteady-RANS analyzes according to shape dimensions were performed. The input design variables for predicting the critical diameter were selected as four geometry parameters that affect the turbulent flow inside the cyclone. As a result of comparing the model prediction performances, the ML model showed the 32.5 % of improvement rate of R2 compared to the traditional MLR considering the nonlinear relationship between the cyclone design variable and the critical diameter. The proposed techniques have proven to be fast and practical tools for cyclone design.

There is an observed general low performance of Ethiopian Sport Governing Bodies (SGBs) in service delivery. Evidence shows that the trend can be corrected with proper understanding and insight into the process of organisational and management factors of these SGBs. This study aimed to investigate the contribution of organisational and management factors on effective sport service delivery in SGBs. For this study, a cross-sectional research design was employed. Purposive sampling was used to choose 350 samples. Pearson Product Moment Correlation Coefficient and multiple regression were used to analyse the data at the 0.05 significant level. The findings confirmed that organisational and management factor variables had a significant positive relationship with sport service delivery (organisational structure (r=0.515), organisational capabilities (r=0.701), communication (r=0.549), management practice (r=0.571), materials & resources (r=0.527) and stakeholders satisfaction (r=0.742). In addition, Management factors were found to be significant contributors for predicting effective sport service delivery (F(3, 329)= 165.868, R2= 0.612). Furthermore, organisational factors had a joint significant contribution to effective sport service delivery (F(3, 329) = 148.743, R2= 0.576). In addition, organisational and management factor variables jointly best predicted effective sport service delivery in Ethiopian SGBs (F(6, 326) =130.81, R2= 0.707). Therefore, this study suggests organisational and management factor variables can be used to predict effective sport service delivery.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

Medical research has suggested that the anterior-posterior (AP)-diameter of the inferior vena cava (IVC) and its associated temporal variation as imaged by bedside ultrasound is useful in guiding fluid resuscitation of the critically-ill patients. This paper develops semi-automatic active ellipse and rectangle algorithms for measurement and tracking of the AP-diameter. The proposed algorithms are compared with an expert manual measurement and the previous work based on active circle model. It is shown that regardless of the shape of the IVC, the rectangle model always outperforms the two other models and performs very close to manual measurement.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

Background Ultrasonographic measurement of the optic nerve sheath diameter (ONSD) is helpful in the assessment of intracranial pressure. The aim of this study was to determine whether the Trendelenburg position during laparoscopic urological surgery changed the ONSD and whether changes correlated with postoperative complications. Methods In this prospective study, we measured ONSD before patients were placed in the Trendelenburg position. Then the Trendelenburg position was established by tilting the operating table to 20-25 degrees. After surgery, the patients were placed in a horizontal position, and the second measurement of ONSD was obtained. Results The study included 69 patients. The average preoperative ONSD in the right eye was 5.8 ± 0.7 mm and 5.8 ± 0.8 mm in the left eye. The average postoperative ONSD in the right eye was 6.6 ± 0.8 mm and 6.6 ± 0.7 mm in the left eye. The differences between postoperative and preoperative values in the right and left eyes were statistically significant (p <0.000001). ONSD increases above the norm did not correlate with the incidence of postoperative nausea (p = 0.94), delirium (p = 0.81), or the time to patient awakening (p = 0.29). Conclusion ONSD increased in patients who underwent surgical procedures performed in the Trendelenburg position, but the increase did not correlate with postoperative complications.

Background: Leishmaniasis is a significant global public health issue that is caused by parasites from Leishmania genus. With limited treatment options and rising drug resistance, there is a pressing need for new therapeutic approaches. Molecular chaperones, particularly Hsp90, play a crucial role in parasite biology and are emerging as promising targets for drug development. Objective: This study evaluates the efficacy of 17-DMAG in treating BALB/c mice from cutane-ous leishmaniasis through in vitro and in vivo approaches. Materials and Methods: We assessed 17-DMAG cytotoxic effect on bone marrow-derived mac-rophages (BMMΦ) and its effects against L. braziliensis promastigotes and intracellular amastigotes. Additionally, we tested the compound's efficacy in BALB/c mice infected with L. braziliensis via intraperitoneal administration to evaluate the reduction of lesion size and de-crease of parasite load in the ears and lymph nodes of infected animals. Results: 17-DMAG showed selective toxicity [selective index=432) towards Leishmania amastigotes, causing minimal damage to host cells. The treatment significantly reduced lesion sizes in mice and results in parasite clearance from ears and lymph nodes. It also diminished in-flammatory responses and reduced the release of pro-inflammatory cytokines (IL-6, IFN-g, TNF) and the regulatory cytokine, IL-10, underscoring its dual leishmanicidal and anti-inflammatory properties. Conclusion: Our findings confirm the potential of 17-DMAG as a viable treatment for cutaneous leishmaniasis and support further research into its mechanisms and potential applications against other infectious diseases.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

A medium scale household in South Africa consumes about 1000 kWh on average, and ae household spend about 3000 ZAR per month on energy supply using grid electricity. Grid electricity. South Africa’s energy is supplied by a huge governmental organization. Statistical analyses indicate that projected increase of the cost of grid electricity in South Africa is about 30% per annum for the next five years. Our research show that Photo-Voltaic (PV) technology can offer a viable alternative, provided a large initial capital outlay can be made. The technology is user-friendly and easy to operate. It is calculated that the cost of electricity, capitalized over 20 years, considering an 80 % supply of needs and assuming 20 sunny days per month, is about 2.80 ZAR. The study also shows that utilizing a hybrid combination of renewable energies, such as combining PV supply with solar thermal energy absorbers, and converting thermal energy to electricity, as energy supply systems, could reduce the current cost of electricity per household in South Africa to about half of national grid supply prize, R1,50 per kWhr. The study also shows that water provides as a most viable medium to store energy, instead of using expensive battery technology to perform such functions.

Natural Fibre Reinforced Composites (NFRCs) represent a significant category of materials that has the capacity to contribute to the worldwide objectives of sustainability and environmental preservation. To maximise the potential of composite materials, it is essential to establish their high quality and cost-effective manufacture. While the basic production procedures for producing items based on NFRCs have reached a high level of development, more research efforts are needed to advance their secondary manufacturing processes, namely in the areas of machining and joining. The primary factor leading to the rejection of composite goods with holes is the damage generated during the drilling process. The present experimental study aims to examine the effectiveness of hole production during the moulding phase. A comparative analysis has been conducted to assess the mechanical characteristics of moulded and drilled holes in jute fibre reinforced epoxy composite. It was observed that the moulded holes exhibit superior performance compared to the drilled holes for jute/epoxy materials. Additionally, the load extension curves indicate that the moulded holes experience greater extension in comparison to the drilled holes.

This study was to identify clinical cancer biomarkers for recurrent gastric cancer survivors using artificial intel-ligence. From a hospital-based cancer registry database in Taiwan, the datasets of the incidence of recurrence and clinical risk features were included in 2476 gastric cancer survivors. We benchmarked Random forest with MLP, C4.5, AdaBoost, and Bagging algorithms on metrics and leveraged synthetic minority oversampling technique (SMOTE) for imbalanced dataset issues, cost-sensitive learning for risk assessment, and SHapley Additive ex-Planations (SHAP) for feature importance analysis in this study. Our proposed Random forest outperformed the other models with an accuracy of 87.9%, a recall rate of 90.5%, an accuracy rate of 86% and F1 of 88.2% on re-current category by a 10-fold cross-validation in a balanced dataset. We identified clinical features of recurrent gastric cancer, which are the top five features, stage, number of regional lymph node involvement, Helicobacter pylori, BMI(body mass index), and gender, which significantly affect the prediction model's output, are worth paying attention to in the following causal effect analysis. Using an artificial intelligence model, the risk factors for recurrent gastric cancer could be identified and cost-effectively ranked according to their feature importance. In addition, they should be crucial clinical features to provide physicians with the knowledge to screen high-risk patients in gastric cancer survivors as well.

The total tree height (h) and diameter at breast height (dbh) relationship is an essential tool in forest management and planning. The height—diameter (h-dbh) relationship had been studied with several approaches and for several species worldwide. The nonlinear mixed effect modeling (NLMEM) has been extensively used and lately the resilient backpropagation artificial neural network (RBPANN) approach has been a trend topic for modeling this relationship. The artificial neural network (ANN) is a computing system based in artificial intelligence and inspired in biological neural network for supervised learning. In this study the NLMEN and RBPANN approaches were used for modeling the h—dbh relationship for Durango pine species (Pinus durangensis Martínez) in mixed-species forest from Mexico. The total dataset considered 1,000 (11,472 measured trees) randomly selected from 14,390 temporary forest inventory plots and the dataset was randomly divided into two parts; 50% for training and 50% for testing. An unsupervised clustering analysis was used to grouped the dataset into 10 clusters based on k-means clustering method and plot-variables like density, basal area, mean dbh, mean h, quadratic mean diameter, altitude and aspect. The RBPANN was performed for tangent hyperbolicus (RBPANN-tanh), softplus (RBPANN-softplus), and logistic (RBPANN-logistic) activation functions for functions in cross product of the covariate or neurons and the weights for the ANN analysis. For both training and testing, 10 classical statistics (e.g., RMSE, R2, AIC, BIC, logLik) were computed for the residual values and assess the approaches for h—dbh relationship. For training and testing, the ANNs approach outperformed the NLMEM approach, and the RBPANN-tanh has the best performance in both training and testing phases.

In this study, we aimed to identify the features of indeterminate choroidal melanocytic lesions visualized on optical coherence tomography angiography (OCTA) and to identify predictors of growth. We retrospectively evaluated 86 patients with indeterminate lesions treated at our cen-tre from 2016 to 2021. Clinical management involved active surveillance followed by brachy-therapy if growth was detected. The lesions were classified into two groups according to wheth-er they grew (small melanomas) or remained stable (choroidal nevi). Growth was detected in 19 (22.1%) lesions. All patients underwent OCTA at baseline. These images were compared to iden-tify possible predictors of growth. Significant between-group differences were observed in thickness (p=0.00), greatest basal diameter (p=0.00), number of risk factors (p=0.00), symptoms (p=0.001; relative risk [RR]: 4.3), orange pigment (p=0.00; RR: 6.02), and ultrasonographic hol-lowness (Kappa sign); p=0.000; RR: 5.3). The melanomas had significantly more vessels with a diameter ≥ 76.3 µm (p=0.02; RR: 2.46). The time to growth in these lesions was significantly shorter (p=0.05) than in lesions with smaller vessels. These findings show that vessel diameter quantified by OCTA can differentiate between choroidal nevi and small melanomas, especially when considered together with clinical risk factors.

The effects on Raychaudhuri's equation of an intrinsically discrete or particle nature of spacetime are investigated, through consideration of null congruences emerging from, or converging to, a generic point of spacetime, i.e. in geometric circumstances somehow prototypical of singularity issues. This is done from an effective point of view, meaning through a (continuous) description of spacetime modified to embody the existence of an intrinsic discreteness on the small scale, adding to previous results for non-null congruences. Various expressions for the effective rate of change of expansion are derived. They in particular provide finite values for the limiting effective expansion and its rate of variation when approaching the focal point; this on top of resulting non vanishing the limiting cross-sectional area itself of the congruence.

Major cardiovascular events (MACE) are a cause of major mortality worldwide. The narrowing and blockage of coronary arteries with atherosclerotic plaques is diagnosed and treated with percutaneous coronary intervention (PCI). During this procedure, coronary angiography (CAG) remains the most widely used guidance modality for the evaluation the affected blood vessel diameter in order to decide if intervention with stent colocation is suitable, where small blood vessels (&lt; 2.75 mm) are majorly left untreated; however, small vessel coronary artery disease (SvCAD) is a significant risk factor for recurrence of MACE, and there are some limitations to the use of CAG that could be improved with the use of newer techniques such as intravascular ultrasound (IVUS), although at higher costs, which might explain their underuse. To address this discrepancy and identify specific cases for its use, we conducted a retrospective study in patients who underwent PCI for MACE with at least one small blood vessel affected. The affected small blood vessels’ diameter was obtained with both CAG and IVUS, additionally we underwent a multivariate analysis to identify risk factors associated with a change in diameter. We included information from 48 patients with mean + SD age of 69.1 + 11.9 years and 34% were masculine gender. We found a significant positive low correlation in diameter measurements of small blood vessels (r=0.1242 p=0.014). Mean diameter with CAG and IVUS was 2.1 mm (95% CI 1.9-2.2), and 2.8 (2.8-3.0) the estimated difference was of 0.8 mm (95 % CI 0.7-0.9). In total 37 (77%) of patients had a reclassification of their blood vessels from a small to medium (2.75-3.00 mm) in 21 cases, or even large (&lt;3.00 mm) in 15 cases, after IVUS; this was important for the decision of intervention and stent collocation. The only variable associated with reclassification of blood vessels after adjusted in a multivariate analysis was DT2 (p=0 0.035). Our findings corroborate that blood vessels might appear smaller with CAG, especially in the diabetes population, therefore at least in these cases the use of IVUS is recommended over CAG.

When a large artery becomes occluded, hemodynamic changes stimulate remodeling of arterial networks to form collateral arteries in a process termed arteriogenesis. However, the structural changes necessary for collateral remodeling have not been defined. We hypothesize that decon-struction of the extracellular matrix is essential to the remodeling of smaller arteries into effective collaterals. Using multiphoton microscopy, we analyzed collagen and elastin structure in maturing collateral arteries isolated from ischemic rat hindlimbs. Collateral arteries harvested at different timepoints showed progressive diameter expansion associated with striking rearrangement of in-ternal elastic lamina (IEL) into a loose fibrous mesh, a pattern persisting at 8 weeks. Despite a 2.5-fold increase in luminal diameter, total elastin content remained unchanged in collaterals compared with control arteries. Among the collateral midzones, baseline elastic fiber content is low. Outward remodeling of these vessels with a 10-20 fold diameter increase was associated with fractures of the elastic fibers and evidence of increased wall tension as demonstrated by straight-ening of the adventitial collagen. Inhibition of lysyl oxidase (LOX) function with β-aminopropionitrile resulted in severe fragmentation or complete loss of continuity of the IEL in developing collaterals. Collateral artery development is associated with permanent redistribution of existing elastic fibers to accommodate diameter growth. We found no evidence of new elastic fiber formation. Stabilization of the arterial wall during outward remodeling is necessary and dependent on LOX activity.

Nowadays, the massive use of tires generates large stocks of waste material which is a serious environmental problem. The usual method used for processing wasted tires is mechanical crushing, in which fiber, steel, and rubber are separated. The aim of this research is the recycling of the obtained rubber, called also GTR (Ground Waste Tires). With this purpose, the paper analyses the mechanical properties of the composites produced by mixing GTR with several industrial polymers. These composites are characterized by the percentage of GTR in the composite and its particle size. These two variables along with seven industrial polymers define a set of composites from which the mechanical properties are analyzed and presented. From the results, it can be drawn that this proposal could be a way to enhance some polymer properties and to contribute in some way to reduce the environmental wasted tires problem.

Barium monofluoride (BaF) is a polar molecule of interest to measurements of the electron electric dipole moment [1, 2]. For this purpose efforts are under way to investigate this molecule embedded within cryogenic matrices, e.g., in solid Ne [3]. For a theoretical understanding of the electronic structure of such an embedded molecule the need arises for efficient methods which are accurate, but also can handle a number of atoms which surround the molecule. The calculation for gas-phase BaF can be reduced to involve only outer electrons by representing the inner core of Ba with a pseudopotential [4] while carrying out a non-relativistic calculation with an appropriate basis set [5]. In this work we demonstrate to which extent this can be achieved using coupled-cluster methods to deal with electron correlation. As a test case the SrF(X 2Σ+ → B 2Σ+) transition is investigated and excellent accuracy is obtained with the EOM-CC3 method. For the BaF(X 2Σ+ → A′ 2∆, X 2Σ+ → A 2Π, X 2Σ+ → B 2Σ+) transitions various coupled-cluster approaches are compared with very good agreement for EOM-CC3 with experimentally derived spectroscopic parameters except for the excitation to the A′ 2∆ state for which the excitation energy is overestimated by 200 cm−1.

We conducted a study to determine if antenatally collected maternal urine cotinine (a me- 13 tabolite of nicotine) measurements can be used to assess the neonatal impact of nicotine exposure 14 during pregnancy. This was a prospective longitudinal cohort of mother-infant dyads. Only term 15 singleton pregnancies were included. The primary outcome measure was the correlation between 16 maternal urine cotinine and infant birth weight. We analysed data from 238 mother-neonates' dy- 17 ads. Urine cotinine was detected in 50.4 % (120/238) women from the whole cohort, but only 16% 18 (38/238) self-reported as smokers (chi-square 39.7, p<0.0001), and these women had significantly 19 smaller babies (p=0.010). There was a significant negative correlation between maternal urine co- 20 tinine and birth weight (Spearman's coefficient = -0.0226, p=0.013). Female babies born to women 21 with nicotine in the urine were significantly smaller (p= 0.001). The number of women exposed to 22 nicotine during late pregnancy (measured in urine) was markedly higher than self-reported and 23 National smoking percentages, suggesting an urgent need for improvement of medical record re- 24 porting on smoking habits to better assess neonatal outcomes.

In drilling small holes with diameters of 1 mm or less, minute clogging and twining of chips or adhesion of the workpiece material can become factors in causing breakages of the drill bit; moreover, it can be difficult to identify the machining state. Acoustic emission (AE) sensing is a nondestructive inspection technique that measures the elastic-stress waves that are generated when a material is deformed and fractured. AE sensing permits highly sensitive measurements to be made without changing the rigidity of the experimental system, unlike force sensing of cutting resistance, etc. In the present study, attempts were made to identify the machining state and tool wear, and to predict abnormalities in small-diameter drilling by using the change in the frequency of AE signal waveforms arising from deformation and fracture. It was shown that it is possible to predict the breakage of the drill bit by detecting the high-frequency AE signals caused by adhesion. In addition, a correlation map of the AE frequency spectrum for identifying the machining state in a drilling operation is suggested.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

Optic nerve sheath diameter (ONSD) can help predict the neurologic outcome of patients with post-cardiac arrest (CA) return of spontaneous circulation (ROSC). We aimed to investigate the effect of ONSD changes before and after CA on neurologic outcomes in patients with ROSC after CA using brain computed tomography (CT). The study included patients hospitalized after CA, who had undergone pre- and post-CA brain CT from January 2001 to September 2020. The patients were divided into good and poor neurologic outcome (GNO and PNO, respectively) groups based on the neurologic outcome at hospital discharge. We performed between-group comparisons of the amount and rate of ONSD changes on brain CT and calculated the area under the curve (AUC) to determine their predictive value for neurologic outcomes. Among the 96 enrolled patients, 25 had GNO. Compared to the GNO group, the PNO group showed significantly higher amount (0.30 vs. 0.63 mm; p=0.030) and rate of change (5.26 vs. 12.29 %; p=0.041). The AUC for predicting PNO was 0.64 (95% CI=0.53–0.73; p=0.04) and patients with a rate of ONSD change &gt;27.2% had PNO with 100% specificity and positive predictive value. Hence, ONSD changes may predict neurologic outcomes in patients with post-CA ROSC.

Controlling functional properties of matter and combine them for engineering a functional device is nowadays a common direction of scientific community. For instance, heterogeneous magnetic nanostructures can make use of different types of geometrical and compositional modulations to achieve the control of the magnetization reversal along with the nano-entities and thus enabling the fabrication of spintronic, magnetic data storage and sensing devices, among others. In this work, diameter modulated FeNi nanowires are fabricated paying special effort to obtain sharp transition regions between two segments of different diameters (from about 450 nm to 120 nm), enabling precise control over the magnetic behavior of the sample. Micromagnetic simulations performed on single bi-segmented nanowires predict a double step magnetization reversal where the wide segment magnetization switches near 200 Oe through a vortex domain wall, while at 500 Oe the magnetization of the narrow one is reversed through a corkscrew like mechanism. Finally, these results are confirmed with magneto-optic Kerr effect measurements at the transition of isolated bi-segmented nanowires. Furthermore, macroscopic vibrating sample magnetometry is used to demonstrate that the magnetic decoupling of nanowire segments is the main phenomenon occurring over the entire fabricated nanowires.

Nonparametric assessments of police technical and scale efficiency is challenging because of the stochastic nature of criminal behavior and because of the subjective dependence on multiple decision criteria, which can lead to a more or less efficiency prospect depending on the regulation, necessity, or organizational objective. There is a trade-off between efficiency and effectiveness in many police performance assessments, i.e., efficient departments (producing more clear-ups with a given resource) are crime-specialized or cannot reproduce those good results effectively on more severe or complex occurrences. This study proposes a combined methodology for carrying out efficiency and effectiveness analysis of Police departments. A conditional non-parametric approach, which allows to include crime as an external factor in the analysis, is combined with a non-compensatory ranking based on the PROMETHEE II methodology for the approach illustrated on the multidimensional efficiency and effectiveness comparison of 145 Pernambuco (Brazil)'s police departments. The application results offer compelling perspectives for public administrations concerning the strategic prioritization of units for rewards or interventions.

Vaccine hesitancy has emerged as a significant barrier to achieving herd immunity and protecting populations from preventable diseases. Despite the proven effectiveness and safety of vaccines, many individuals remain hesitant or refuse to vaccinate themselves or their children. This review aims to identify the factors contributing to vaccine hesitancy, including misinformation, lack of trust in authorities, cultural beliefs, and access barriers. We also discuss the impact of vaccine hesitancy on public health, including outbreaks of vaccine-preventable diseases and erosion of trust in public health authorities. Furthermore, we present evidence-based communication strategies for addressing vaccine hesitancy, including building trust, providing accurate information, addressing myths and misconceptions, engaging with local influencers, and utilizing social media and digital platforms. By understanding the factors contributing to vaccine hesitancy and implementing effective communication strategies, healthcare providers, public health officials, and community leaders can work towards promoting widespread vaccine acceptance and protecting public health.

By using geodesic equations to obtain a gravitational potential generated from a point-like source, we end up in the concept of a nearly Newtonian gravity to analyse effective potentials of quasi-circular orbits. By means of an approximate solution from an axially static and symmetric Weyl metric, we study an effective gravitational potential to obtain its related rotation curves, orbital planes and orbits. Moreover, using as initial condition a Plummer sphere, some prospects on star cluster disruption are also discussed in this framework.

Medical waste management is crucial issues for keeping our life safe and safety. Without effective measures for waste management, we cannot keep ourselves safe from different types of contagious diseases; viruses, bacteria. Knowledge sharing assists healthcare staff in identifying and mitigating hazards on appropriate handling, segregation and disposal medical waste. The aim of the study is to identify a multifaceted analysis of knowledge sharing, training, communication and attitudes for effective medical waste management. This study selected 153 medical workers randomly, including nurses, lab technologists, and cleaners, from hospitals, diagnostic centers, and clinics in the northern part of Bangladesh. The study design of this research is mixed-methods. This research adopts a survey and interview as a research strategy. The samples are collected randomly. SPSS software packages, MS Excel Office, and PLS-SEM are used to analyze data. Most of the respondents always share their knowledge face-to-face according to the findings. The result also shows that there are positive relationship between sources of knowledge (p: 0.046), awareness and knowledge (p: 0.049), attitudes of waste management (p: 0.025) and effective medical waste management. However, there are no relationships between communication and collaboration (p: 0.943), the practice of waste management (p: 0.155), supervision and staff monitoring (p: 0.527), training and education (p: 0.656) and effective medical waste management. Its focus on the northern part of Bangladesh introduces regional specificity, potentially limiting the applicability of results to other regions. The knowledge-sharing practices for waste management among medical staff are examined within this research, along with the relationship between attitude, awareness, and knowledge, staff supervision and monitoring, practice, training, and education and effective medical waste management that have not been studied before home and abroad. This analysis highlights the critical need for an integrated approach to medical waste management, emphasizing the importance of continuous education, open communication, and cultivating a culture that prioritizes environmental sustainability. The insights from this study offer practical recommendations for healthcare institutions to improve their medical waste management practices, ultimately leading to enhanced health outcomes and better environmental protection.

The paper investigates the possible use of a low strength domestic sand (D) (up to today useless – not considered as proppant source) of small particle sizes, instead to that of high strength imported commercial sand (C), as a prospective micro-proppant for low permeability reservoirs in Poland. There is need to develop national unconventional gas resources like tight gas, shale gas and coalbed methane. An important energy source of value and readily available in Poland is coal. The basins of this resource are large and bears low permeability coalbed methane reservoirs which needs to be developed to contribute to the energy security, economy and environmental needs of the country. These reservoirs need technological assistance such as hydraulic fracturing which makes use of proppants for development. Most of the commonly used proppants over the years for fracturing have been large grain size commercial proppants of high strength material content bought abroad. Investigated finer proppants are known to have the ability to penetrate narrow fracture networks to ensure effective high reservoir volume and conductivity for production. Results from presented laboratory research shows the D - proppant, which is cheaper and readily available, has the 3K class with low settling rates as a potential micro-proppant for effective transportation, enhancement of conductivity and production rate in the narrow fractures of low permeability reservoirs. Future using of domestic proppant will decrease stimulation cost and will have positive impact on the environment due to omitting long distance transportation from abroad.

Recent technological advancements in conservation genetics and genomics have resulted in diverse tools for aiding conservation of species. The precision and resolution of high throughput sequencing technologies provide valuable insights to aid conservation decisions, but these technologies are often financially unfeasible or unavailable in resource constrained countries. Inter-Simple Sequence Repeat (ISSR) markers, when combined with sensitive automated detection systems, provide a simple, cheap means to investigate genetic diversity and discriminate closely related species. Here we apply this technology to assess genetic diversity and taxonomic delimitation in the Encephalartos eugene-maraisii species complex, a highly threatened, taxonomically dubious group of cycads in South Africa. Our analyses support taxonomic singularity of E. dyerianus, E. dolomiticus and E. eugene-maraisii. Relationships between E. nubimontanus and E. cupidus remain uncertain. E. middelburgensis samples showed no clustering but had poor amplification success. This study demonstrates the suitability of automated ISSR fingerprinting as a method for plant conservation studies, especially in resource-constrained countries, and we make recommendations as to how this methodology can be effectively implemented.

Modelling diameter distribution is an integral part of forest management. It requires the use of a suitable probability density function or cumulative distribution function with the appropriate fitting method. In this study, we compared the suitability of eight probability density functions fitted by derivative and optimization methods used for diameter distribution estimation of forest stands. The derivation and optimization were used on A Charlier, beta, generalized beta, gamma, Gumbel, Johnson’s SB, and Weibull (2 and 3-parameter). We used data from 167 permanent sample plots from Atlantic forest (Quercus robur) and 59 temporary sample plots from tropical forests (Tectona grandis). The quality of the fits was evaluated with different indices such as Kolmogorov–Smirnov, Cramer-von Mises, mean absolute error, bias and mean squared error. The results showed Johnson’s SB function was more suitable for describing the diameter distribution of the stands. Johnson’s SB, 3-parameter Weibull and generalized beta had consistent performance regardless of the fitting methods. The quality of fits produced by gamma, Gumbel and 2-parameter Weibull was poor.

(1) Background: There is a need of a novel surrogate marker to ease decision making when facing ascending aortic dilatation. In this article we study the ratio between ascending and descending aorta diameters as a potential one; (2) Methods: Retrospective observational cohort study, including all the patients who have undergone surgery for aTAAD between January 2014 and September 2020 at our center. A total of 50 patients were included. Clinical and demographic data was collected. Anatomical measurements were made including orthogonal maximal diameters of the ascending and descending aorta, post-dissection whole circumference length (post-wCL), post-dissection true lumen circumference length (post-tCL), surface and sphericity index of the ascending and descending aorta. Pre-dissection ascending aorta diameter (pre-AAD) and pre-dissection descending aorta diameter (pre-DAD) were calculated as well as the ratio between them and compared with reference values; (3) Results: 96% of the patients pre-AAD was smaller than the recommended 55mm. The ratio between the descending and ascending aorta pre-dissection diameters was significantly smaller compared to the reference value (0.657±0.125 versus 0.745± 0.016 with a mean difference of -0.088 and a p&lt;0.001); (4) Conclusions: The 55mm threshold for aorta maximal diameter is an insufficient criterion when assessing the risk of dissection. The ratio between DAD and AAD is a parameter worthy of analysis as a tool to stratify the risk of dissection.

Distributed tracing is a cutting-edge technology for monitoring, managing, and troubleshooting native cloud applications. It offers a more comprehensive and continuous observability, surpassing traditional logging methods, and is indispensable for navigating modern complex software architectures. However, the sheer volume of generated traces is staggering in distributed applications, and direct storage and utilization of every trace are impractical due to associated operational costs. This entails a sampling strategy to select which traces warrant storage and analysis. Historically, sampling methods have included a rate-based approach, often relying heavily on a manual configuration. There is a need for a more intelligent approach, and we propose a hierarchical sampling methodology to address multiple requirements concurrently. Initial rate-based sampling mitigates the overwhelming volume of traces, as no further analysis can be performed on this level. In the next stage, more nuanced analysis is facilitated based on the previous foundation, incorporating information regarding trace properties and ensuring the preservation of vital process details even under extreme conditions. This comprehensive approach not only aids in the visualization and conceptualization of applications but also enables more targeted analysis in later stages. As we delve deeper into the sampling hierarchy, the technique becomes tailored to specific purposes, such as simplifying application troubleshooting. In this context, the sampling strategy prioritizes the retention of erroneous traces from dominant processes, thus facilitating the identification and resolution of underlying issues. The focus of this paper is to reveal the impact of the sampling on troubleshooting efficiency. Leveraging intelligent and explainable artificial intelligence solutions enables the detection of malfunctioning microservices and provides transparent insights into root causes. We advocate for using rule-induction systems, which offer explainability and efficacy in decision-making processes. By integrating advanced sampling techniques with machine learning-driven intelligence, we empower organizations to navigate the complexities of large-scale distributed cloud environments effectively.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li.

We use oblate coordinates to study its resulting orbit equations. Their related solutions of Einstein's vacuum equations can be written as a linear combination of Legendre polynomials of positive denite integers $l$. Starting from solutions of the zeroth order $l=0$ in a nearly newtonian regime, we obtain a non-trivial formula favoring both retrograde and advanced solutions for the apsidal precession depending on parameters related to the metric coecients, particularly applied to the apsidal precessions of Mercury and asteroids (Icarus and 2 Pallas). As a realization of the equivalence problem in general Relativity, a comparison is made with the resulting perihelion shift produced by Weyl cylindric coordinates and the Schwarzschild solution analyzing how different geometries of space-time influence on solutions in astrophysical phenomena.

Background: The transversus abdominis plane (TAP) block has gained increasing importance as a very effective pain relief in for caesarean section. This study aimed to compare bupivacaine (Group B), bupivacaine with dexmedetomidine (Group BD) and bupivacaine with dexamethasone (Group BDx) applied in ultrasound-guided TAP block in the treatment of CS postoperative pain. Material and Method: American Society of Anesthesiologists I and II pregnant women who underwent cesarean section were included in the study. Forty patients were admitted in each group. All patients were applied TAP block with ultrasound guidance by administering the medications of the group in which they were included. Results: Body mass index (BMI) and operation duration were higher in Group B (p*=0.01 and 0.004, respectively). Instant tramadol requirement and amount were higher in Group B at some of follow up times. Patient satisfaction scale were better in Group BD and Group BDx. Conclusion: TAP block significantly reduces pain after cesarean section, prolongs the time to first analgesic request, and reduces the need for additional opioid analgesics. The addition of adjuvant to the TAP block usually improves the postoperative clinical condition. However, some special conditions such as body mass index (BMI) may negatively affect the clinical situation. Comprehensive, standardized, randomized controlled studies are needed to compare results under different conditions.

Supplier collaboration and partnership in procurement are essential elements for enhancing organizational efficiency, innovation, and resilience in today's globalized markets. This qualitative study investigates the dynamics of effective supplier relationships, focusing on trust, communication, innovation, quality, cost savings, and resilience as critical factors. Data were gathered through semi-structured interviews, case studies, and document analysis across diverse industries, highlighting insights from procurement professionals and supplier representatives. Key findings underscore the foundational role of trust and communication in fostering successful collaborations. Establishing transparent, ongoing communication channels facilitates mutual understanding, reduces conflicts, and enhances overall satisfaction. Collaborative innovation emerged as pivotal, enabling organizations to pool resources and expertise for product development and process improvement. Quality and reliability were identified as significant outcomes of close partnerships, particularly in industries with stringent standards such as aerospace and healthcare. Furthermore, the study reveals substantial cost savings and efficiency gains through collaborative efforts in process optimization and waste reduction. Effective risk management practices within these partnerships enhance supply chain resilience, enabling organizations to anticipate and mitigate disruptions proactively. Despite these benefits, challenges such as cultural differences, technological integration, and regulatory compliance require strategic mitigation strategies. In conclusion, organizations can optimize supplier collaborations by prioritizing trust-building, fostering a culture of innovation, and investing in robust relationship management practices. This approach not only enhances operational performance but also positions organizations to navigate market uncertainties and achieve sustainable growth in a competitive landscape.

The global trend towards increased demand for organic food, greener environments, and the integration of biological control agents into pest management strategies has greatly enhanced the need for biological pesticides (biopesticides). Biopesticides are generally environmentally friendly and are made from micro-organisms or other natural substances. Despite their great potential, relatively few have been registered and commercialised in Nigeria compared to other African countries such as South Africa and Kenya. Biological active agents are so diverse such that ap-plying the same safety standards or environmental conditions to all of them is almost impossible. A review of risk assessment processes and comparative assessments of Nigeria's biopesticide regulations with other developing African countries and developed regions was conducted. Prolonged field testing, lack of bridged risk assessments and technical checklists have been identified as key factors hampering the timely development and commercialisation of biopesti-cides in Nigeria. Recommendations on necessary changes to the existing Nigeria biopesticide regulations have been made. Risk assessment matrices for microbial and biochemical biopesti-cides and a scientific/technical checklist have also been developed. Harmonisation and data ex-change among other countries in the region will also enhance the advancement of scientific and technical knowledge for sustainable regulation and cross-border trade.

Mosquitoes carrying endosymbiotic bacteria called Wolbachia are being released in mosquito and arbovirus control programs around the world. Open field releases of Wolbachia-infected male mosquitoes have achieved over 95% population suppression, while the replacement of populations with Wolbachia-infected females is self-sustaining and can greatly reduce local dengue transmission. Despite many successful interventions, significant questions and challenges lie ahead. Wolbachia, viruses and their mosquito hosts can evolve, leading to uncertainty around the long-term effectiveness of a given Wolbachia strain, while few ecological impacts of Wolbachia releases have been explored. Wolbachia strains are diverse and the choice of strain to release should be made carefully, taking environmental conditions and the release objective into account. Mosquito quality control, thoughtful community awareness programs and long-term monitoring of populations are essential for all types of Wolbachia intervention. Releases of Wolbachia-infected mosquitoes show great promise, but existing control measures remain an important way to reduce the burden of mosquito-borne disease.

We review past and present results on the non-local form-factors of the effective action of semiclassical gravity in two and four dimensions computed by means of a covariant expansion of the heat kernel up to the second order in the curvatures. We discuss the importance of these form-factors in the construction of mass-dependent beta functions for the Newton's constant and the other gravitational couplings.

Cardiovascular diseases (CVD) are the leading cause of morbidity and mortality worldwide, including in Croatia. Since most patients have multiple disorders and diseases caused largely by the same risk factors, and as it is essential to approach each patient as a person with all disorders, today we are talking about a new paradigm - cardio-renal-metabolic (CKM) syndrome and cardio-renal-metabolic health, which necessarily includes brain health. Elevated systolic blood pressure, LDL cholesterol, smoking, obesity, diabetes, impaired renal function or chronic kidney disease, which all stem from insufficient physical activity, unhealthy diet with excessive intake of table salt, and air pollution, are the leading causes of overall morbidity and mortality from CKM diseases, especially mortality from CVD. Experts from various fields key to CKM health have written this document with the aim of integrating it as part of the national plan for the prevention of chronic non-communicable diseases with a focus on CVD, which should become mandatory and be based on the existing guidelines of professional societies.

Environmental estrogen pollution and estrogen effects on the female reproduction system are well-recognized scientifically. Among the estrogens, 17 β-estradiol is a priority in environmental estrogen pollution, and it is also a major contributor to estrogen which regulates the female reproduction system. 17 β-estradiol is carcinogen and has a tumor promotion effect relating to breast cancer, lung cancer and others. It also affects the psychological well-being such as depression, fatigue and others. Thus, a simple method of detection of 17 β-estradiol will be important for both environmental estrogen pollution and women’s health care. This study demonstrates a simple-use, cost effective 17 β-estradiol biosensor system which can be used for both environment and women’s health care applications. The bio-recognition mechanism is based on the influence of the redox couple, K₃Fe (CN) ₆/K₄Fe (CN) ₆ by the interaction between 17 β-estradiol antigen and its α-receptor (ER- α; α-estrogen antibody). The transduction mechanism is an electrochemical analytical technique, differential pulse voltammetry (DPV). The levels of 17 β-estradiol antigen studied was between 2.25 pg/mL to 2,250 pg/mL, Phosphate buffered saline (PBS), tap water from the Cleveland regional water district, and simulate urine were used as the test media covering the potential application areas for 17 β-estradiol detection. An interference study by testosterone which has a similar chemical structure and molecular weight as those of 17 β-estradiol was carried out, and this 17 β-estradiol biosensor showed excellent specificity without any interference by similar chemicals.

The calculation of effective doses is crucial in many medical and radiation fields, in order to ensure safety and compliance with regulatory limits. Traditionally, Monte Carlo codes using detailed human body computational phantoms have been used for such calculations. Monte Carlo dose calculations can be time-consuming and require expertise in different processes when building the computational phantom and dose calculations. This study employs various machine learning (ML) algorithms to predict the organ doses and effective dose conversion coefficients (DCCs) for different anthropomorphic phantoms. A comprehensive data set comprising neutron energy bins, organ labels, masses, and densities is compiled from Monte Carlo studies, and is used to train and evaluate the supervised ML models. This study includes a broad range of phantoms, including those from the International Commission of Radiation Protection (ICRP-110, ICRP-116 phantom), the Visible-Human Project (VIP-man phantom), and the Medical Internal Radiation Dose Committee (MIRD-Phantom), with row data prepared using numerical data and organ categorical labeled data. Extreme gradient boosting (XGB), gradient boosting (GB), and the random forest-based Extra Trees regressor are employed to assess the performance of the ML models against published ICRP neutron DCC values using the mean square error, mean absolute error, and R² metrics. The results demonstrate that the ML predictions significantly vary in lower energy ranges and vary less in higher neutron energy ranges, while showing good agreement with ICRP values at mid-range energies. Moreover, the categorical data models align closely with the reference doses, suggesting the potential of ML in predicting effective doses for custom phantoms based on regional populations, such as the Saudi voxel-based model. This study paves the way for efficient dose prediction using ML, particularly in scenarios requiring rapid results without extensive computational resources or expertise. The findings also indicate potential improvements in data representation and the inclusion of larger data sets to refine model accuracy and prevent overfitting. Thus, ML methods can serve as valuable techniques for the continued development of personalized dosimetry.

This study investigates effective strategies for second language education in primary schools, analyzing the efficacy of immersive and interactive methods, digital literacy tools, and mixed-method approaches. The findings reveal significant improvements in language proficiency and student engagement through these methodologies, with immersive and interactive strategies showing substantial benefits in oral proficiency and engagement, digital tools enhancing accessibility and engagement, and mixed-method approaches yielding the highest overall effectiveness. The study underscores the importance of a balanced, flexible approach to language education, integrating traditional and modern methods to cater to diverse learner needs. These strategies not only advance linguistic skills but also contribute to the broader cognitive and emotional development of young learners, emphasizing the critical role of effective language education in preparing students for a globalized world.

Fractals and multifractals are well-known trademarks of nonlinear dynamics and classical chaos. The goal of this work is to tentatively uncover the unforeseen path from multifractals and selfsimilarity to the framework of effective field theory (EFT). An intriguing finding is that the partition function of multifractal geometry includes a signature analogous to that of gravitational interaction. Our results also suggest that multifractal geometry may offer insights into the non-renormalizable interactions presumed to develop beyond the Standard Model scale.

Why animals sleep is an outstanding open question. Information about the toxic byproducts of aerobic cellular respiration along with the analysis of patterns in animal size, sleep needs, dietary-type, metabolism, number of heart beats, transportation-network design, and transportation energetics/dynamics suggest that the function of sleep is to maximize the time an animal has to perform its life functions given the finite and constant number of lifetime heart beats it has. Sleep slows down metabolism, and the heart rate, thereby decreasing the load of toxic reactive oxygen species in the cell and extending the cell’s lifetime/proper-functioning. I argue that this is used to maximize the time an animal spends in its ‘effective environment’, which is defined as the period in the light cycle (day or night) where the essential life-functions of that animal (like finding resources, finding sex, hunting) are better achieved. Larger, slow-metabolizing animals need less sleep because their large-bodily-networks and slow metabolisms keep their heart rates relatively low, resulting in a lower rate of oxidative damage, and more relative time in the ‘effective environment’ to get their essential life-functions accomplished.

In this paper we have discussed the importance of human resource management in project management. As a concept human resource management emerged in 1980 [9]. It is very important to utilize resources effectively in any organization. Like triple constrains (cost, quality, scope) human resources are also considered as one of the most important factor for the success of any project. Management of human resources involve hiring experienced workers, giving appropriate training, acknowledgement about the significance of the project and the effective use of techniques and tools in order to get the project done productively with in time and budget. It becomes the responsibility of the project manager to effectively manage human resources as it is more challenging than managing other technical resources. In this paper we have also discussed the challenges that an organization faced during the management of the resources and use of some strategic human practices in order to overcome these challenges.

This paper shows the development of a numerical analysis model which enables the calculation of the life of a reduced-diameter wheel used for freight wagons as a function of its operating factors. Reduced-diameter wheels are being increasingly used for combined transport applications and they can be arranged in a wide range of bogies and operated very differently. Due to the uniqueness of this type of wheels, their life has hardly been analyzed so far. To properly construct the numerical analysis model, it has been necessary to study the rolling phenomenon in-depth, tackle the main problems arising in the vehicle – track interaction and set the relations amongst them. Once the rail-wheel interaction model was built, it was used to calculate the life of an ordinary-diameter wheel, a medium-diameter wheel and a reduced-diameter wheels under the same conditions and compare them. In this way, it is possible to know how long the life of a reduced-diameter wheel is compared to that of an ordinary-diameter one and also the evolution of the life depending on the diameter. The root causes responsible for this evolution can be explained thanks to the comprehension of the rolling phenomenon provided by the full analytical work.

Biosecurity is a tool used to alleviate the introduction, emergence and spread of diseases caused by infectious agents. It comprises different health-management activities that need to be followed to reduce the passage and dissemination of infectious agents within and among farms, poultry flocks, and humans, as well as within a country, among countries, or the whole globe. In terms of public health measures, biosecurity applies to practices that will reduce contact between poultry and humans and thereby reduce zoonotic disease transmission. Two of the common biosecurity measures are bioexclusion and biocontainment which themselves are further categorized as segregation/isolation, movement control and hygiene/sanitation/disinfection. Isolation is about putting poultry under an exclusively isolated environment where it lives alone without any interference from any source external to the poultry or at least under reduced and controlled interference. Movement/traffic control and sanitation measures are practices to follow the isolation of poultry or preparatory phase as in the case of sanitation of poultry houses before introduction of poultry. These techniques have been effective in controlling poultry diseases like avian influenza, exotic Newcastle, Marek’s disease, and any other diseases. Depending upon the underlying situation either bioexclusion or biocontainment measure will be used to control these infectious diseases of poultry.

This paper presents a comprehensive and adaptive framework for orchid conservation programs illustrated with data from published and unpublished case studies. There is a specific focus on West Australian terrestrial orchids, but many of the approaches have universal relevance. Aspects of the framework include (1) setting appropriate objectives, (2) establishing effective collaborations between scientists, volunteers and regulators to fill knowledge and funding gaps, (3) use of survey and demographics data to determine extinction risks and management requirements for species, (4) effective habitat management to overcome threats such as grazing, (5) finding potential new habitats by modelling climate and site data, (6) investigating the effectiveness of pollinators and (7) using seed baiting to detect mycorrhizal fungi. The relative cost and effectiveness of different methods used to propagate orchids for translocation are compared. Methods known to be successful, in order of complexity, include placement of seed in situ, vegetative propagation, symbiotic germination in non-sterile organic matter, symbiotic germination in sterile culture, asymbiotic sterile germination and clonal division in tissue culture. These form a continuum of complexity, cost, time required, faculties needed, as well as the capacity to maintain genetic diversity and produce seedlings preadapted to survive in situ. They all start with seed collection and lead to seed storage, living collections used as tuber banks and seed orchards, as well as translocation for conservation. They could also lead to commercial availability and sustainable ecotourism, both of which are needed to reduce pressure on wild plants. Overall, there has been a strong preference to use relatively complex, expensive and time-consuming methods for orchid conservation, despite evidence that simpler approaches have also been successful. These simpler methods, which include in situ seed placement and non-sterile germination on inorganic substrates, should be trialled in combination with more complex orchid propagation methods as part of an adaptive management framework. It is essential that orchid conservation projects harness the unique biological features of orchids, such as abundant seed production and mycorrhizal fungi which are far more widespread than their hosts. This is necessary to increase the efficiency and coverage of recovery actions for the largest and most threatened plant family.

Programmed death ligand 1 (PD-L1) is a co-inhibitory molecule expressed on the surface of various cell types, known for its suppressive effect on T cells through interaction with PD-1. Neutrophils also express PD-L1, and its expression is elevated in specific situations; however, the immunobiological role of PD-L1+ neutrophil has not been fully characterized. Here, we report that PD-L1-expressing neutrophils increased in methicillin-resistant Staphylococcus aureus (MRSA) infection are highly functional in bacterial elimination and supporting inflammatory resolution. The frequency of PD-L1+ neutrophils was dramatically increased in MRSA-infected mice, and this population exhibited enhanced activity in bacterial elimination compared to PD-L1- neutrophils. An administration of PD-L1 monoclonal antibody did not impair PD-L1+ neutrophil function suggesting that PD-L1 expression itself does not influence neutrophil activity. However, PD-1/PD-L1 blockade significantly delayed liver inflammation resolution in MRSA-infected mice, as indicated by increased plasma alanine transaminase (ALT) level and frequencies of inflammatory leukocytes in the liver implying that neutrophil PD-L1 suppresses the inflammatory response of these cells during the acute phase of MRSA infection. Our results reveal that elevated PD-L1 expression can be a marker for enhanced anti-bacterial function of neutrophils. Moreover, PD-L1+ neutrophils are an indispensable population attenuating inflammatory leukocyte activities assisting in a smooth transition into the resolution phase in MRSA infection.

We investigate regular damped oscillatory structures appearing in the "effective" form factor of various hadrons. The behavior of this form factor can be extracted from the experimental information on total cross sections, the processes $\sigma_{tot}(e^+e^- \to h \bar h)$, $h=\pi^{\pm}, K^{\pm}, K^0, p, n $ are examined. The apparent oscillations have been observed for the first time for the proton and we show, taking also other hadrons into the consideration, that they are an arbitrary artifact resulting from a very simplistic theoretical description based on an elementary three-parametric model. If the data are described by a more appropriate and well physically funded U\&A model, then the oscillations disappear. In addition, if the simple model is used to describe the data, one observes that the oscillations are opposite for particles which form an isospin dublet. We show, by using the U\&A model, that this feature is explained by the transformation properties of the corresponding states in the isotopic space.

Natural ventilation in a building is an effective way to achieve acceptable indoor air quality. Ventilation dilutes contaminants such as bio-effluents generated by occupants, substances emitted from building materials, and water vapor generated by occupants' activities. In a building that requires heating and cooling, adequate ventilation is crucial to minimize energy consumption while maintaining healthy indoor air quality. However, measuring the actual magnitude of the ventilation rate, including infiltration through the building envelope and airflow through building openings, is not always feasible. In this study, the occupant-generated carbon dioxide (CO2) tracer gas decay method was applied to estimate the ventilation rates in an office room in Seoul, South Korea, from summer to winter. Using the method, real-time ventilation rates can be calculated by monitoring indoor and outdoor CO2 concentrations without injecting a tracer gas. 145mm-diameter circular openings on the fixed glass were used for natural ventilation in the test room. As a result, firstly, the indoor CO2 concentrations were used as an indicator to evaluate how much the indoor air quality deteriorated when all the windows were closed in an occupied office room compared to international standards for indoor air quality. Moreover, we found out the estimated ventilation rates varied depending on various environmental conditions, even with the same openings for natural ventilation. Considering the indoor and outdoor temperature differences and outdoor wind speeds as the main factors influencing the ventilation rates, we analyzed how they affected the ventilation rates in different seasons of South Korea. When the wind speeds were calm, the temperature difference played as a factor that influences the estimated ventilation rates. On the other hands, when the temperature differences were low, the wind speed was the primary factor. This study raises awareness about the risk of poor indoor air quality in office rooms that could lead to health problems or unpleasant working environments. This study presents an example of estimating the ventilation rates in an existing building. In the same way, the ventilation rate in an existing building can be simply estimated while using the building as usual, and appropriate ventilation strategies for the building can be determined to maintain desired indoor air quality.

The Internet of Things (IoT) generates a large volume of data whenever devices are interconnected and exchange data across a network. As a result, there is a range of services with varying needs, for example, capacity requirements, data quality, and latency demands. These services operate on fog computing devices, which are limited in power and bandwidth compared to the cloud. The main challenge is deciding where to implement services on the fog, the cloud, or the hybrid. This paper proposes an efficient allocation technique that pushes processing closer to the network's fog side. It investigates which devices and services may best allocate while preserving resource usage in the IoT architecture. It also examines the importance of allocating services to devices and optimizing resource use in fog computing. In IoT settings, there is a wide range of services and devices; thus, it is critical to effectively assign the services to the devices. We propose Priority-based Service allocation (PSA) and Sort-based Service Allocation (SSA) techniques, which are used to enable an optimum order to employ devices to perform the various services. The experimental results indicate that our proposed technique minimize the data communication over the network by 82% by allocating most of the services locally in fog. We have maximized the number of distributed services to fog devices by 90% while minimizing the wastage of fog resources.

Existing one-shot neural architecture search (NAS) methods have to conduct a search over a giant super-net, which leads to the huge computational cost. To reduce such cost, in this paper, we propose a method, called FTSO, to divide the whole architecture search into two sub-steps. Specifically, in the first step, we only search for the topology, and in the second step, we search for the operators. FTSO not only reduces NAS’s search time from days to 0.68 seconds, but also significantly improves the found architecture's accuracy. Our extensive experiments on ImageNet show that within 18 seconds, FTSO can achieve a 76.4% testing accuracy, 1.5% higher than the SOTA, PC-DARTS. In addition, FTSO can reach a 97.77% testing accuracy, 0.27% higher than the SOTA, with nearly 100% (99.8%) search time saved, when searching on CIFAR10.

Research has shown that second language reading is the bridge that leads to developing otherlanguage skills such as speaking, writing, and vocabulary acquisition. Hence, the present studyaimed to explore adult language learners’ perspectives regarding the most effective andbeneficial reading strategies that can be used to develop their reading competency. Using aqualitative research method, the study examined what specific reading strategies languagelearners believe is effective in developing their reading skills. Analysis of the focus groupsrevealed five different reading strategies mentioned by the participants. These strategies were:Reading Aloud, Silent Reading, Shared Reading, Scanning or Skimming, and Timed Reading. Findings suggest that understanding the use of different reading strategies is important, solanguage teachers need to devote more learning time to introduce reading strategies during ESL classes.

VE is a powerful technique for analyzing a design with a focus on functionality, reducing costs, and increasing value. However, in order to proceed with the design of VE, the theoretical basis for the VE target selection process, which must be preceded in the preparation stage, is lacking, and as a result, it is difficult to verify the most effective target selection. Thus, a theoretical basis is needed. In this study, we intend to quantify the WORTH value of the COST TO WORTH technique and present an objective model of the target selection method using the derived Value Index (VI). For this purpose, cost worth (WORTHC) was calculated based on the performance data of 1,008 cases of 15 building types provided by the Domestic Public Procurement Service and the share of 83 detailed processes in 7 fields. Then, a survey was conducted targeting the ordering companies, and the final worth (WORTHF) was calculated by multiplying the derived customer value (WORTHV ) weight for each detailed work type. We calculated the Value Index (VI) by comparing COST and WORTHF for each detailed construction type of the VE project and developed a model to select construction types that exceed the VI standard value derived using the standard error of the population. Both cost experts and non-cost experts can use the developed model to specify the VE target selection criteria in order to easily select the key target, objectively sort the values that serve as the basis for calculating the value index and make it possible to more easily select the VE target selection criteria based on theoretical evidence. Also, the model can be used to obtain effective detailed design VE results.

Intestinal parasitic infections pose a grave threat to human health, particularly in tropical and subtropical regions. The traditional manual microscopy system of intestinal parasites detection remains the golden standard procedure for the diagnosis of parasites cyst or eggs, but this approach is costly time-consuming (30min/sample), highly tedious, and also required specialist. However, computer vision based on deep learning has made great stride in recent time. Despite the significant advances in deep convolutional neural network-based architectures, little research has been conducted to explore the potential of these techniques in the field of parasitology, specifically for intestinal parasites. Therefore, the goal of this research is to evaluate the performance of proposed state-of-the-art transfer learning architecture for detecting and classifying intestinal parasite eggs from images. We would ensure that patients receive prompt treatment while also relieving experts of extra work if we used such an architecture. Here, in stage first, we applied image pre-processing and augmentation to the dataset, and in stage second, we utilized the YOLOv5 algorithms for detection and classification and then compared their performance based on different parameters. Our algorithms achieved a mean average precision of 97% approximatiely and 8.5 ms detection time per sample for 5,393 intestinal parasite images. Thus, this approach may form a solid theoretical basis for real-time detection and classification in routine clinical examinations while accelerating the process to satisfy increasing demand.

In this study, the fuzzy c- means classifier has been studied with nine other similarity and dissimilarity measures: Manhattan distance, chessboard distance, Bray-Curtis distance, Canberra, Cosine distance, correlation distance, mean absolute difference, median absolute difference and normalised squared Euclidean distance. Both single and composite modes were used with a varying weight constant (m) and also at different α-cuts. The two best single norms obtained were combined to study the effect of composite norms on the datasets used. An image to image accuracy check was conducted to assess the accuracy of the classified images. Fuzzy Error Matrix (FERM) was applied to measure the accuracy assessment outcomes for a Landsat-8 dataset with respect to the Formosat-2 dataset. To conclude FCM classifier with Cosine norm performed better than the conventional Euclidean norm. But, due to the incapability of the FCM classifier to handle noise properly, the classification accuracy was around 75%.

Unmanned aerial vehicles (UAVs), commonly known as drones, present a cost-effective solution for the swift collection of data from vast and remote areas that are otherwise difficult to access. The Mediterranean Basin, known for being a hot spot for plant biodiversity, hosts several habitats and taxa of significant naturalistic value. However, many of these areas are often inaccessible to botanists, making exploration and research challenging. The aim of this paper is to involve the utilization of drone surveys and open-source software for botanical research. Our primary goal is to show the effectiveness of these tools in the field and demonstrate their practical application in Natura 2000 sites. The protected area chosen for this research is Rocca di Novara, situated in northeastern Sicily. Thanks to our drone investigations, we were able to capture images of the mountain’s side that is inaccessible to humans. This allowed us to observe the habitat of some species in detail. One of the most fascinating discoveries was the reappearance of Saxifraga callosa subsp. australis, which had not been confirmed in this area for over 140 years. Using drones for botanical research can boost field research, making monitoring easier and more cost-effective over time, especially in Natura 2000 sites.

In this paper, we study the effect of decreasing aperture diameter on signal transmission from the scintillator to the PMT. The apertures have been inserted directly between the scintillator and the photomultiplier. Three different aperture diameters have been used over a wide energy range.A newly developed fast digital spectrometer has been utilised for experimental measurement in the radial channel of the VR-1 research reactor. The detector signals with and without inserted apertures have been measured and evaluated. The aim of our research was to determine the effect of the apertures on the spectral quality, energy range and the evaluated physical quantities.

This paper is a follow-up to a previous study that was conducted in a research forest and identified the optimal method for Diameter at Breast Height (DBH) estimation as a circular scanning and fitting ellipses to 4cm stem cross-sections at breast height. The aim of this study was to determine whether the identified method is applicable to natural boreal forests as well. The iPad Pro LiDAR scanner was used to acquire point clouds for 15 sites representing a range of natural boreal forest conditions in Ontario, Canada, and estimate DBH. The secondary objective was to determine if tested stand (Species composition, age, density, understory) or tree (Species, DBH) factors affected the accuracy of estimated DBH. Overall, estimated DBH values were within 1cm of actual DBH values for 78 of 133 measured trees (59%). An RMSE of 1.5cm (8.6%) was achieved. Stand age had a large effect (&gt;0.15) on the accuracy of estimated DBH values, while density, understory, and DBH had moderate effects (0.05-0.14). No trend was identified between accuracy and stand age. Accuracy improved as understory density decreased and as tree DBH increased. Inertial Measurement Unit (IMU) and positional accuracy errors with the iPad Pro scanner limit the feasibility of using this device for forest inventories.

Critical sized bone defects and articular cartilage injuries resulting from trauma, osteonecrosis or age-related degeneration are often nonhealing by the physiological repairing mechanisms, thus representing a clinic issue due to the relevant epidemiological incidence. Current treatment approaches consist of autologous or allogenic grafting, which are associated with painfulness, morbidity, risk of infections and rejection. Novel tissue-engineering approaches, aiming at the reconstruction of damaged tissues, have been proposed as alternative solutions to these conven-tional methods. These approaches are based on the combination of three fundamental compo-nents: autologous or allogenic cells, a scaffold and growth-stimulating signals, which are gener-ally referred to as the tissue engineering triad. Three-dimensional polymer networks are fre-quently used as scaffolds to allow cell proliferation and tissue regeneration. In this scenario, cryogels are giving promising results as cell scaffolds over other polymer networks, thanks to their peculiar properties. In particular, cryogels possess an interconnected porous structure and a typical sponge-like behaviour, which facilitate the cellular infiltration and ingrowth. Their properties can be appropriately adjusted to match the requirements of the specific tissue or or-gan that it is intended to regenerate. In this review it is reported the state of the art on the fabri-cation and employment of cryogels in supporting osteo or chondro-genic differentiation for the re-building of more organized tissues. Moreover, it will highlight current progress and future perspectives in the implementation of this technology in the clinical practice.

Biodiversity conservation questions human practices towards biodiversity and, therefore, largely conflicts with ordinary societal aspirations. Decisions on the location of protected areas, one of the most convincing conservation tools, reflect such a competitive endeavor. Operations Research (OR) brings a set of analytical models and tools capable of resolving the conflicting interests between ecology and economy. Recent technological advances have boosted the size and variety of data available to planners, thus challenging conventional approaches bounded on optimized solutions. New models and methods are requested to use such a massive amount of data in integrative schemes addressing a large variety of concerns. Here, we provide an overview on the past, present and future challenges that characterize spatial conservation models supported by OR. By enlarging the spatial, temporal, taxonomic and societal horizons of biodiversity conservation planners navigate around multiple bio-socioeconomic equilibria and are able to decide on cost-effective strategies to improve biodiversity persistence.

This paper is intended to correlate the impact of leadership skills on organizations' performance, all organizations grow differently, and their growth depends mostly on positive performance from one year to another which has direct correlations to the leadership dreams, visions, foresight and aspirations for the organization. There is one thing for the leader to have vision, but the leader needs to have followership to assist in implementing their vision to make it goals which translate to performance in the organization and growth. The leadership style or management skills greatly influence how they command and motivate followership to actualize their dreams or the organizational visions and mission which results in the organization's performance. A positive leadership influence produces or actualizes a positive organisational performance that will move the organization towards the vision of the organization. Knowing the difference between a manager and a leader is pertinent in explaining the correlation between leadership and organizational performance. The understanding of these two roles provides credence to the correlation between effective leadership and organisational performance, and the understanding of the term, the use and the importance of strategic management to leadership and organizational performance. There is a wide difference between managers and leaders, which is based on personality and their approach to the resolution of challenges they are confronted with.

The research employs both literature and experimental data to develop reasonable strategies for melon fly control. The objects of research were sierozem soils of the Zhanakorgan region (Kyzylorda region), bentonite clays of the Sauran region (Turkestan region), vermicompost obtained at the production site of the Research Institute "Ecology" at the International Kazakh-Turkish University named after Khoja Ahmed Yasawi. The competitive agent 'Vermiserbent' was developed by combining sulphur-perlite-containing waste (SPCW), vermicompost (VC), and natural bentonite clay. When incorporated into the soil, it serves as both an insecticide and a fertiliser recovery agent. Disinfection and enrichment of barren Sierozem soils in southern Kazakhstan could provide an eco-friendly approach to protect cucurbits (melon, watermelon, and pumpkin) against the melon fly. The average yield of watermelon treated with vermiserbent increased by 2.3 t/ha compared to the control, melon by 4.6 t/ha, pumpkin by 5.6 t/ha. The marketability of gourds as watermelons and melon after treatment with fertilizer increased by 1.2 times, and pumpkin by 1.1 times. The findings of studies conducted in agricultural fields in the Turkestan and Kyzylorda regions have shown that it is possible to produce environmentally sound gourds using a mixture of vermicompost, bentonite, and SPCW.

In this study, we evaluated and compared several major carbon sequestration methods based on the first principles, namely, energy use efficiency and elemental stoichiometry. This study suggested that, at present, wood burial is the only feasible carbon sequestration method because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture.

MicroRNAs (miRNAs) are small endogenous RNAs that regulate gene expression post-transcriptionally by targeting either the 3′ untranslated or coding regions of genes. They have been reported to play key roles in a wide range of biological processes. The recent remarkable developments of transcriptomics technologies, especially next-generation sequencing technologies and advanced bioinformatics tools, allow more in-depth exploration of messenger RNAs (mRNAs) and non-coding RNAs (ncRNAs) including miRNAs. These technologies have offered great opportunities for a deeper exploration of miRNA involvement in farm animal diseases, as well as livestock productivity and welfare. In this review, we provide an overview of the current knowledge of miRNA roles in farm animal diseases with a particular focus on diseases of economic importance. In addition, we discuss the steps and future perspectives of using miRNAs as biomarkers and molecular therapy for livestock disease management as well as the challenges and opportunities for understanding the regulatory mechanisms of miRNAs related to disease pathogenesis.

Behavior of supported alloyed and de-alloyed platinum-copper catalysts, which contained 14% - 27% wt. of Pt, was studied in the reactions of methanol electrooxidation (MOR) and oxygen electroreduction (ORR) in 0.1 M HClO4 solutions. Alloyed PtCux/C catalysts were prepared by a multistage sequential deposition of copper and platinum onto a Vulcan XC72 dispersed carbon support. De-alloyed PtCux-y/C catalysts were prepared by PtCux/C materials pretreatment in acid solutions. The effects of the catalysts initial composition and the acid treatment condition on their composition, structure, and catalytic activity in MOR and ORR were studied. Functional characteristics of platinum-copper catalysts were compared with those of commercial Pt/C catalysts when tested, both in an electrochemical cell and in H2/Air membrane-electrode assembly (MEA). It was shown that the acid pretreatment of platinum-copper catalysts practically does not have negative effect on their catalytic activity, but it reduces the amount of copper passing into the solution during the subsequent electrochemical study. The activity of platinum-copper catalysts in the MOR and the current-voltage characteristics of the H2/Air PEMFC MEAs measured in the process of their life tests were much higher than those of the Pt/C catalysts.

Ever since pharmacy has become a profession, pharmacist's role has been continuously subjected to changes due to specific influences from historical, socio-economic, political, and scientific context. Nowadays the classic perception of pharmaceutical profession in Community Pharmacy is facing worldwide extinction due to many factors. Modern services, such as online, mail-order, and telephone-order pharmacies are increasingly gaining ground thanks to their ability to facilitate customer demand. However, at the same time, they are endangering “face-to-face” contact, affecting the building of customer loyalty based on direct “human” interaction, and consequently reducing pharmacists to mere commercial figures. Communication is in fact emphasized as the essential element to build a solid and appropriate interpersonal relationship with the client, to make the consultancy process effective, and to strengthen pharmacist's professionalism in community pharmacy. The aim of this work is to analyze pharmacist’s role in modern society by pinpointing the factors affecting pharmacy profession practice. Specific purpose will be improving both the academic training of future professionals and their capacity to approach public relations through a deepened study and practice of behavioral, communication, educational, and sociological methodologies and techniques that would allow the development of more effective communication skills useful for providing an efficient consultancy service.

The increasing spatial and spectral resolution of hyperspectral imagers yields detailed spectroscopy measurements from both space-based and airborne platforms. Machine learning algorithms have achieved state-of-the-art material classification performance on benchmark hyperspectral data sets; however, these techniques often do not consider varying atmospheric conditions experienced in a real-world detection scenario. To reduce the impact of atmospheric effects in the at-sensor signal, atmospheric compensation must be performed. Radiative Transfer (RT) modeling can generate high-fidelity atmospheric estimates at detailed spectral resolutions, but is often too time-consuming for real-time detection scenarios. This research utilizes machine learning methods to perform dimension reduction on the transmittance, upwelling radiance, and downwelling radiance (TUD) data to create high accuracy atmospheric estimates with lower computational cost than RT modeling. The utility of this approach is investigated using the instrument line shape for the Mako long-wave infrared hyperspectral sensor. This study employs physics-based metrics and loss functions to identify promising dimension reduction techniques. As a result, TUD vectors can be produced in real-time allowing for atmospheric compensation across diverse remote sensing scenarios.

The description of the electron-electron interactions in two-dimensional materials has a dimensional mismatch, where electrons live in (2+1)D while photons propagate in (3+1)D. In order to define an action in (2+1)D, one may perform a dimensional reduction of quantum electrodynamics in (3+1)D (QED4) into Pseudo quantum electrodynamics (PQED). The main difference between this model and QED4 is the presence of a pseudo-differential operator in the Maxwell term. However, besides the Coulomb repulsion, electrons in a material are subjected to several microscopic interactions, which are inherent in a many-body system. These are expected to reduce the range of the Coulomb potential, leading to a short-range interaction. Here, we consider the coupling to a scalar field in PQED for explaining such mechanism, which resembles the spontanoues symmetry breaking (SSB) in Abelian gauge theories. In order to do so, we consider two cases: (i) By coupling the gauge field to a Higgs field in scalar quantum electrodynamics in (3+1)D and, thereafter, performing the dimensional reduction and; (ii) By coupling a Higgs field to the gauge field in PQED and subsequently calculating its effective potential. In case (i), we obtain a model describing electrons interacting through the Yukawa potential and, in case (ii), we show that SSB does not occur at one-loop approximation. The relevance of the model for describing electronic interactions in two-dimensional materials is also adressed.

Effective management of water distribution systems requires an integrated approach, but none of the available frameworks for one are in broad use in the water supply industry. Frameworks developed include a management standard of the American Water Works Association and Distribution System Optimization, a methodology for physical, hydraulic, and water quality performance assessment. The intelligent systems framework also offers a pathway to integration, but it lacks a definite structure. The voluntary aspect of adopting innovations within the fragmented and unregulated nature of the water utility industry poses a barrier to adoption of such innovations. Another barrier is the uncoordinated arrangements of water research stakeholders with different incentive structures. Intelligent water systems offer a way to incentive utilities to encourage implementation. They can provide a bottom-up approach where utilities see advantages, as opposed to a top-down approach where they are expected to adopt a method without seeing clear benefits. Research to develop new and improved tools is needed, but the research roadmap should prioritize implementation.

Focal vibration therapy can provide neurophysiological benefits. Unfortunately, standardized protocols are non-existent. Previous research presents a wide range of protocols with a wide range of effectiveness. This paper is part of a broader effort to identify effective, standardized protocols for focal vibration therapy. The vibration characteristics of four commercially available focal vibration devices that have been used for research and clinically were measured. An accelerometer was used for the measurements. Frequency and peak-to-peak amplitude were measured. Measurements were made when the devices were free and then again when they were strapped to the human body. Vibration frequency ranged from 120 to 225 Hz. Free vibration amplitude ranged from 2.0 to 7.9 g’s (peak-to-peak). When the devices were strapped to the body (constrained), vibration amplitude decreased by up to 65.7%. These results identify effective ranges of focal vibration frequency and amplitude. They illustrate the importance of identifying vibration environment, free or constrained, when quoting vibration characteristics. Finally, the inconsistency of multi-actuator devices is discussed. These results will guide protocol development for focal vibration and potentially better focal vibration devices.

Climate change from anthropogenic activities represents a serious threat to life in earth. Agriculture releases significant emissions of greenhouse gases (GHG), but also offers low-cost opportunities to mitigate GHG emissions. This paper assesses agricultural GHG emissions in Aragon, one important and representative region for agriculture in Spain. The Marginal Abatement Cost Curve (MACC) approach is used to analyze the abatement potential and cost-efficiency of mitigation measures under several scenarios, with and without taking into account the interaction among measures and their transaction costs. The assessment identifies the environmental and economic outcomes of different combinations of measures. Moreover, we develop future mitigation scenarios for agriculture toward the year 2050, in order to assess the impacts on GHG emissions. Results highlight the importance of assessing biophysical processes in mitigation measures, and the significant effects of interactions between measures that reduce the abatement potential and worsen the cost-efficiency. The inclusion of transaction costs provides a better ranking of measures and a more accurate estimation of implementation costs. The scenario analysis shows how the combinations of measures could reduce emissions and promote sustainable agriculture in the future. Keywords: Climate change; mitigation measures; biophysical processes; cost-efficiency; abatement costs; transaction costs; policy scenarios.

Power disaggregation aims at determining the appliance-by-appliance electricity consumption leveraging upon a single meter only, which measures the entire power demand. Data-driven procedures based on Factorial Hidden Markov Models have been proven remarkable results on energy disaggregation. Nevertheless, those procedures have various weaknesses: there is a scalability problem as the number of devices to observe raises and the algorithmic complexity of the inference step is severe. DNN architectures, such as Convolutional Neural Networks, have demonstrated to be a viable solution to deal with FHMMs shortcomings. Nonetheless, there are two significant limitations: a complicated and time-consuming training system based on back-propagation has to be employed to estimates the neural architecture parameters, and large amounts of training data covering as many operation conditions as possible need to be collected to attain top performances. In this work, we aim to overcome those limitations by leveraging upon the unique and useful characteristics of the extreme learning machine technique, which is based on a collection of randomly chosen hidden units and analytically defined output weights. Experiment evaluation has been conducted using the UK-DALE corpus. We find that the suggested approach achieves similar performances to recently proposed ANN-based methods and outperforms FHMMs. Besides, our solution generalises well to unseen houses.

Titanium membranes are used for guided bone regeneration in implant therapy. However, as a bioinert material, titanium does not have the ability to accelerate bone formation. Various titanium surface treatments to confer bioactivity have been demonstrated; however, there are concerns about the influence of chemical treatments on the corrosion of thin titanium membranes. This study investigated the influence of surface modifications on the structure of thin titanium membranes. Titanium membranes of 20 µm thickness were treated with acid or alkali solutions, and we evaluated their surface structure, wettability, corrosion depth, and mechanical strength compared to non-treated membranes. Alkali-treated thin titanium membranes displayed the formation of nanoscale pore structures on their surfaces, enhanced hydrophilicity, and less corrosion depth compared with acid-treated membranes. Furthermore, the tensile strength of alkali-treated membranes was comparable to non-treated membranes. These results suggest that alkali treatment is an appropriate surface modification method for thin titanium membranes.

Iron ore processing involves critical steps that affect the quality of the final product. Determining the diameter of the pellets is the necessary initial step for volume measurement and, ultimately, for porosity and bulk density measurement, crucial characteristics for optimizing the burning process in the blast furnace. Traditional measurement methods using mercury present issues related to operator safety and environmental preservation, while the practices described in ISO 4698 standard require lengthy preparation and execution time. In light of environmental needs, operator safety, and the time consumed in tests, implementing a new method based on digital image processing and convolutional neural networks for measuring the diameter of burnt iron ore pellets is proposed. The methodology involves capturing images of the pellets using a high-resolution camera and utilizing digital image processing and neural networks capable of performing pixel-by-pixel object segmentation in the images, providing precise information about the pellets to calculate their volume automatically. The results were compared with those obtained using traditional methods, evaluating their conformity with the ISO 4698 standard. In conclusion, this study offers a new approach to measuring the volume of burnt iron ore pellets, providing accurate and reliable results in compliance with safety and environmental preservation standards.