The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The toxic cadmium (Cd) poses a serious threat to plant growth and human health. Populus euphratica CPK21 has previously been shown to attenuate Cd toxicity by reducing Cd accumulation, enhancing antioxidant defense and improving water balance in transgenic Arabidopsis. Here, we confirmed a protein-protein interaction between PeCPK21 and AtNF-YC3 by yeast two-hybrid, HaloTag pull-down and bimolecular fluorescence complementation assays. AtNF-YC3 was induced by Cd and strongly expressed in PeCPK21-overexpressed plants. Overexpression of AtNF-YC3 in Arabidopsis reduced salt inhibition of root length, fresh weight and membrane stability under Cd stress conditions (100 µM, 7 d), suggesting that AtNF-YC3 appears to contribute to the improvement of Cd stress tolerance. AtNF-YC3 improved Cd tolerance by limiting Cd uptake and accumulation, activating antioxidant enzymes, and reducing H2O2 production under Cd stress. We conclude that PeCPK21 interacts with AtNF-YC3 to limit Cd accumulation, enhance the ROS scavenging system, and thereby positively regulate plant adaptation to Cd environments. This study highlights the interaction between PeCPK21 and AtNF-YC3 under Cd stress conditions, which can be utilized to improve Cd tolerance in higher plants.

The fourth industrial revolution has resulted in the digitalization of projects and operations across all sectors. Accordingly, efforts are being made to utilize advanced technologies to improve the energy efficiency of the building sector. This study has reviewed the current application and limitations of cutting-edge technologies in this regard. An overview of the use of the Internet of Things (IoT), artificial intelligence (AI), digital twin (DT), and building information modeling (BIM) for energy efficiency of buildings has been provided. It has been found that the use of Industry 4.0 technologies, during the construction and operational phase of buildings, has a great potential to reduce energy consumption and emissions of the sector. This study may help stakeholders of the built environment to understand the role of industry 4.0 tools for energy efficiency of the sector.

Precast concrete sandwich panels (PCSP) are energy efficient building system that is achieved through an insulation layer created between the concrete wythes. The insulation layer is usually of low bearing strength material making it more applicable for non-structural building systems. Hence, shear connectors are introduced to improve its structural capacity, which subsequently degrades it thermal performance by serving as thermal bridges across the panel. This article review researches of alternative materials and methods used to improve the thermal efficiency as well as reduced the strength loss due to insulation in PCSP. The alternative materials are basalt fibre reinforced polymer (BFRP), carbon fibre reinforced polymer (CFRP), glass fibre reinforced polymer (GFRP), and foam concrete which are selected due to their low thermal conductivity for use in shear connection. While thermal path method has been used to prevent the effect of thermal bridges. Although, some of these materials have successfully achieved the desirable behaviours, however, several undesirable properties such as brittleness, bond slip, the sudden crushing of the panel system, and FRP failure below its ultimate strength were observed. Hence, the practicality of the alternative materials is still questionable despite its higher cost compared to the conventional steel and concrete used in the PCSP system.

This paper attempts to alter a prevailing assumption that buildings use energy to an understanding that in fact, people use energy. Therefore, to successfully accelerate the transition to a low-carbon society and economy more emphasis should be on motivating people and increasing their awareness by making them energy conscious building users and therefore active players in the energy transition process. In this context, this paper provides insights from the Horizon 2020 MOBISTYLE project. It demonstrates research and development approaches, highlights the main project objectives, and presents findings of an ethnographic (qualitative) study of users’ habits, practices, and needs. The aim of the project is to motivate behavioural change by raising consumer awareness through the provision of attractive personalized information on user’s energy use, indoor environment and health, all enabled by an integrated information and communication technology (ICT) service. In this context, the anthropological people-centred approach is integrated into the MOBISTYLE approach putting users at the centre of the ICT tools development process. The main quantitative objective of the project is a reduction of energy use for at least 16 % prompted by the provision of combined information and feedback systems on energy, indoor environmental quality (IEQ) and health. The most relevant motivational factors and key performance indicators (KPIs) for encouraging a more energy conscious and healthy lifestyle were defined by means of a people-centred approach, adopting anthropological inquiries in different settings. Information about users’ lifestyles and their needs was collected in focus groups with potential users in five case studies, located in different European Union (EU) countries. Behaviour change is achieved through awareness campaigns, which encourage users to be pro-active about their energy consumption and to simultaneously improve health and well-being.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

This work focuses on identifying the most effective machine learning techniques and supervised learning models to precisely estimate power output from Photovoltaic (PV) plants. The performance of various regression models is analyzed by harnessing experimental data, including Random Forest, Support Vector Regression (SVR), Multi-layer Perceptron (MLP), Linear Regressor (LR), Gradient Boosting, and k-Nearest Neighbors (KNN). The methodology applied starts with meticulous data preprocessing steps aimed at ensuring dataset integrity. Following the preprocessing phase, which entails eliminating missing values and outliers using Isolation Feature selection based on a correlation threshold, is performed to identify relevant parameters for accurate prediction in PV systems. Subsequently, Isolation Forest is employed for outlier detection, followed by model training and evaluation using key performance metrics such as Root Mean Squared Error (RMSE), Normalized Root Mean Squared Error (NRMSE), Mean Absolute Error (MAE), and R-squared (R2). Among the array of models evaluated, Random Forest emerges as the top performer, highlighting promising results with an RMSE of 19.413, NRMSE of 0.048% and an R2 score of 0.968. Furthermore, the best-performing model is integrated into a MATLAB application for real-time predictions, thereby enhancing usability and accessibility for a wide range of applications in renewable energy.

Heat emitters constitute the primary devices used in space heating and cover a fundamental role in the energy efficient use of buildings. In the search for an optimized design, heating devices should be compared with a benchmark emitter with maximum heat emission efficiency. However, such an ideal heater still needs to be defined. In this paper we perform an analysis of heat transfer in a European reference room, considering room side effects of thermal radiation and computing the induced operative temperature both analytically and numerically. By means of functional optimization, we analyse trends such as the variation of operative temperature with radiator panel dimensions, finding optimal configurations. In order to make our definitions as general as possible, we address panel radiators, convectors, underfloor (UFH) and ceiling heater. We obtain analytical formulas for the operative temperature induced by panel radiators and identify the 10-type as our ideal radiator, while the UFH provides the best performance overall. Regarding specifically UFH and ceiling heaters, we find optimal sizes that identify the according ideal emitters. The analytical method and quantitative results reported in this paper can be generalized and adopted in most studies concerning the efficiency of different heat emitter types in building enclosures.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Western countries are experiencing an increasing aging population, resulting in heightened disability and mobility issues. This trend is expected to escalate in the coming decades. Therefore, ensuring adequate accessibility in collective residential housing –where individuals spend much of their daily lives– is of paramount importance. This paper presents a case study focused on the accessibility of building entrances in collective residential housing in Southeast Spain, specifically in the Region of Murcia. In this region, 9.8% of the population has disabilities, and 15.75% were over 64 years old in 2020. The study began by compiling the relevant national and regional accessibility regulations for existing buildings. Subsequently, extensive fieldwork was conducted, analyzing 150 collective residential housing buildings. Based on this analysis, a set of recommendations to enhance accessibility was formulated for buildings not complying with the regulations. The results are presented and discussed in detail. The most frequent recommendation was the construction of accessible ramps, identified as the primary solution in over 40% of cases, either alone or in conjunction with other measures. In 54% of the cases, multiple interventions were necessary to achieve effective accessibility adaptation. The findings of this study could inform the development of public policies aimed at improving accessibility conditions in urban areas.

Color image binarization plays a pivotal role in image preprocessing work, significantly impacting subsequent tasks, particularly in text recognition. This paper concentrates on Document Image Binarization (DIB), aiming to separate a image into foreground (text) and background (non-text content). Through a thorough analysis of conventional and deep learning-based approaches, we conclude that prevailing DIB methods leverage deep learning technology. Furthermore, we explore the receptive fields pre- and post-network training to underscore the Transformer model's advantages. Subsequently, we introduce a lightweight model based on the U-Net structure, enhanced with the Mobile ViT module to better capture global information features in document images. Given its adeptness at learning both local and global features, our proposed model exhibits superior performance on two standard datasets (DIBCO2012 and DIBCO2017) compared to state-of-the-art methods. Notably, our proposed DIB method presents a straightforward end-to-end model devoid of additional image preprocessing or post-processing. Moreover, its parameter count is less than a quarter of the HIP'23 model, which achives best results on three datasets(DIBCO2012, DIBCO2017 and DIBCO2018). Finally, two sets of ablation experiments were conducted to verify the effectiveness of the proposed binarization model.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Drowsiness is a main factor for various costly defects, even fatal accidents in areas such as construction, transportation, industry and medicine, due to the lack of monitoring vigilance in the mentioned areas. The implementation of a drowsiness detection system can greatly help to reduce the defects and accident rates by alerting individuals when they enter a drowsy state. This research proposes an Electroencephalography (EEG) based approach for detecting drowsiness. EEG signals are passed through a preprocessing chain composed of artifact removal and segmentation to ensure accurate detection followed by different feature extraction methods to extract the different features related to drowsiness. This work explores the use of various machine learning algorithms such as Support Vector Machine (SVM) the K Nearest Neighbor (KNN) the Naive Bayes (NB) the Decision Tree (DT) and the Multilayer Perceptron (MLP) to analyze EEG signals sourced from the DROZY database, carefully labeled into two distinct states of alertness (awake, and drowsy). Segmentation into 10-second intervals ensures precise detection, while a relevant feature selection layer enhances accuracy and generalizability. The proposed approach achieves high accuracy rates of 99.84% and 96.4% for intra (subject by subject) and inter (cross-subject) modes, respectively. SVM emerges as the most effective model for drowsiness detection in the intra mode, while MLP demonstrates superior accuracy in the inter mode. This research offers a promising avenue for implementing proactive drowsiness detection systems to enhance occupational safety across various industries.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

When profit-driven renewal is difficult to implement, many historic districts are “frozen protected” in China. In the social context of “building cities for the people” in recent years, the public value-oriented renewal of urban historic areas plays an important role in the transformation of cities. This study investigates the strategies of historic district regeneration in China by integrating spatial form, urban governance, and public value. We propose a novel framework to analyze the regeneration of historic districts, using Taiyuan Bell Tower Street as a case study. The framework distinguishes between two dimensions: spatial and economic-social. In the spatial dimension, we focus on the transformation of spatial form to regenerate public value, emphasizing the attribute of "publicness" as central to urban regeneration efforts. This involves a tiered approach of excavating and upgrading historic districts at macro, meso, and micro levels. In the economic-social dimension, we explore urban governance to strengthen public value, involving government, market, and societal actors in a collaborative renewal process. The analysis highlights that a public value-oriented approach to heritage regeneration offers greater sustainability and could serve as a model for other cities seeking similar outcomes.

This study explores the transformative potential of integrating Building Information Modeling (BIM) and Generative Design methodologies in heritage conservation and building management. By utilizing BIM, detailed architectural, structural, and MEP models were created, facilitating precise design and effective stakeholder collaboration. Generative Design enabled the exploration of multiple design solutions, optimizing spatial layouts and structural integrity. The project also integrated automated management systems and IoT sensors to enhance real-time monitoring, energy efficiency, and user comfort through the development of a digital twin. Despite encountering challenges such as technical complexities and budget constraints, the project successfully preserved the cinema's historical essence while incorporating modern functionalities. The findings highlight the contributions of BIM and Generative Design to the AEC industry, emphasizing their role in improving design accuracy, operational efficiency, and sustainability. This research provides valuable insights for future projects in heritage conservation, offering a blueprint for balancing historical preservation with contemporary needs. The revitalization of the "Ex Cinema Santa Barbara" in Paternò exemplifies these advancements, demonstrating how these technologies can restore and modernize culturally significant historical buildings effectively.

The article presents the author’s works in the field of modifications and modeling of the PQC CSIDH algorithm on non-cyclic supersingular Edwards curves and its predecessor CRS scheme on ordinary non-cyclic Edwards curves are reviewed. Lower estimates of the computational speed gains of the modified algorithms over the original ones are obtained. The most significant results were obtained by choosing classes of non-cyclic Edwards curves connected as quadratic twist pairs instead of cyclic complete Edwards curves, as well as the method of algorithm randomization as an alternative to “constant time CSIDH.” It is shown that in the CSIDH and CSIKE algorithms, there are two independent cryptosystems with the possibility of parallel computation, eliminating the threat of side-channel attacks. For the CRS scheme, there are four such cryptosystems. Integral lower bound estimates of the performance gain of the modified CSIDH algorithm are obtained at 1.5 ∙ 29, and for the CRS scheme are 3 ∙ 29.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The construction industry is a key driver of environmental change due to its extensive ‎use of resources and high levels of emissions, thus placing a significant burden on global ‎efforts towards sustainable development targets. A large portion of the environmental ‎footprint of buildings results from the energy required to sustain indoor comfort levels. ‎Therefore, enhancing the energy efficiency of existing buildings becomes critical in ‎reducing their environmental impact. This study examines the influence of increasing ‎thermal performance with the aim of reducing heating ‎demand. Thus, numerical modelling tools and different energy performance assessment meth-odologies have been used. ‎Specifically, it evaluates two existing residential buildings in Romania and compares ‎heating demand predictions using PHPP and Mc001-2022 methodologies across various ‎climatic data sets and case studies. The results reveal significant variability in heating ‎demand predictions, emphasizing the importance of methodological choice and climatic ‎data. The ‎study highlights that both PHPP and Mc001-2022 methodologies yield varying results ‎depending on the specific conditions and characteristics of each building. This variation in results underscores ‎the necessity for a nuanced and context-specific approach to energy performance ‎assessment, in-corporating multiple energy efficiency measures tailored to the unique ‎features of each building.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Graph Neural Networks (GNNs) are powerful models capable of managing intricate connections in non-Euclidean data, such as social networks, physical systems, chemical structures, and communication networks. Despite their effectiveness, the large-scale and complex nature of graph data demands substantial computational resources and high performance during both training and inference stages, presenting significant challenges, particularly in the context of embedded systems. Recent studies on GNNs have investigated both software and hardware solutions to enhance computational efficiency. Earlier studies on Deep Neural Networks (DNNs) have indicated that methods like reconfigurable hardware and quantization are beneficial in addressing these issues. Unlike DNN research, studies on efficient computational methods for GNNs are less developed and require more exploration. This survey reviews the latest developments in quantization and FPGA-based acceleration for GNNs, showcasing the capabilities of reconfigurable systems (often FPGAs) to offer customized solutions in environments marked by significant sparsity and the necessity for dynamic load management. It also emphasizes the role of quantization in reducing both computational and memory demands through the use of fixed-point arithmetic and streamlined vector formats. This paper concentrates on low-power, resource-limited devices over general hardware accelerators and reviews research applicable to embedded systems. Additionally, it provides a detailed discussion of potential research gaps, foundational knowledge, obstacles, and prospective future directions.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Despite Low Power Wide Area Networks’ ability to offer an extended range, it might still encounter challenges with coverage blind spots in the network. This article proposes an innovative energy-efficient nature-inspired relay selection algorithm for LoRa-based LPWAN networks, serving as a solution for challenges related to poor signal range in areas with limited coverage. A behavior swarm-inspired approach has been utilized to select the relays’ localization in the network, providing network energy efficiency and radio signal extension. These relays help bridge communication gaps, significantly reducing the impact of coverage blind spots by forwarding signals from devices with poor direct connectivity with the gateway. The proposed algorithm considers critical factors for the LoRa standard, such as the Spreading Factor or device energy budget analysis. The simulation experiments validate the proposed scheme’s effectiveness in terms of energy efficiency under diverse multi-gateway topology scenarios involving thousands of devices. Specifically, it has been verified that the proposed approach outperforms the reference method in preventing the battery depletion of relays, which is vital for battery-powered IoT devices. Furthermore, for some large-scale problems, the proposed heuristic method achieves over twice the speed of the exact method with a negligible accuracy loss of less than 2%.

Mobile Edge Computing (MEC) integrated with Wireless Power Transfer (WPT) is emerging as a promising solution to reduce task delays and extend the battery life of Mobile Devices (MDs). Cooperative user communication, or relay technology, enhances communication efficiency for users located far from the base station by mitigating the double near-far effect caused by distance. This is considered a key technology in Beyond 5G (B5G) and future communication systems. In this paper, we focus on maximizing the long-term energy efficiency (EE) of a user-cooperation WPT-MEC system, while taking into account the uncertain load dynamics at the edge MD and the time-varying state of the wireless channel. The joint optimization of wireless charging time fraction, MD offloading duration, helper node processing time, and transfer power decision presents significant challenges due to the coupling of data offloading among cooperative users and a volatile system environment. To address these challenges, we formulate the problem as a stochastic programming problem and propose an online control algorithm, DOUCA, to solve it. Our approach utilizes Dinkelbach’s method and Lyapunov optimization theory to decouple the sequential decision problem into a deterministic sub-problem for each time slot. For the sub-problem, we use variable substitution to convert the non-convex problem into a convex one, containing only a small number of variables, which can be efficiently solved. Furthermore, we provide a mathematical analysis of our algorithm’s performance. Extensive simulation results demonstrate the effectiveness of our proposed algorithm, as evidenced by an impressive energy efficiency improvement of over 20% compared to benchmark methods. Our algorithm also achieves a trade-off between EE and system stability.

Private Set Intersection (PSI) is a cryptographic method in secure multi-party computation that allows entities to identify common elements in their datasets without revealing their private data. Traditional approaches assume similar-sized datasets and equal computational power, overlooking practical imbalances. In real-world applications, dataset sizes and computational capacities often vary, particularly in the Internet of Things and mobile scenarios where device limitations restrict computational types. Traditional PSI protocols are inefficient here, as computational and communication complexities correlate with the size of larger datasets. Thus, adapting PSI protocols to these imbalances is crucial. This paper explores unbalanced PSI scenarios where one party (the receiver) has a relatively small dataset and limited computational power, while the other party (the sender) has a large amount of data and strong computational capabilities. It introduces three innovative solutions for unbalanced PSI: unbalanced PSI protocol based on Cuckoo filters, unbalanced PSI protocol based on single cloud assistance, and unbalanced PSI protocol based on dual cloud assistance, each addressing the shortcomings of the previous solution. These protocols primarily optimize database computational load, storage capacity, protocol execution time, and security. Depending on performance and security needs, different protocols can be employed for applications such as private contact discovery.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

Unmanned aerial vehicles (UAVs) have increasingly become integral to multi-access edge computing (MEC) due to their flexibility and cost-effectiveness, especially in the B5G and 6G eras. This paper aims to enhance the Quality of Experience (QoE) in large-scale UAV-MEC networks by minimizing the shrinkage ratio through optimal decision-making in computation mode selection for each user device (UD), UAV flight trajectory, bandwidth allocation, and computing resource allocation at edge servers. However, the interdependencies among UAV trajectory, binary task offloading mode, and computing/network resource allocation across numerous IoT nodes pose significant challenges. To address these challenges, we formulate the shrinkage ratio minimization problem as a mixed-integer nonlinear programming (MINLP) problem and propose a two-tier optimization strategy. To reduce the scale of the optimization problem, we first design a low-complexity UAV partition coverage algorithm based on the Welzl method and determine the UAV flight trajectory by solving a Traveling Salesman Problem (TSP). Subsequently, we develop a coordinate descent (CD) based method and an alternating direction method of multipliers (ADMM) based method for network bandwidth and computing resource allocation in the MEC system. The CD-based method is simple to implement and has a low computational complexity, while the ADMM-based method can further enhance the optimization result through joint optimization. Extensive simulations demonstrate that our proposed algorithms perform well in large-scale edge networks and outperform other representative benchmark methods.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

This study aims to quantify greenhouse gas (GHG) emissions from China's sludge treatment industry and explore the potential of novel technologies to mitigate these emissions, promoting sustainable sludge management practices. Using a life cycle assessment approach, the total GHG emissions from sludge treatment in 2017 were estimated at 18.54 Mt CO2-eq, with significant regional variations. Incineration contributed the highest emissions (1,011.53 kg CO2-eq/t dry sludge), followed by landfill (717.51 kg CO2-eq/t) and land application (276.41 kg CO2-eq/t). The uneven distribution of emissions across cities highlights the need for targeted mitigation strategies that consider local sustainability challenges. Principal component analysis revealed that economic factors and treatment scale significantly influence emissions, emphasizing the importance of integrating sustainability goals with economic development. To reduce the carbon footprint of sludge treatment and enhance sustainability, the mitigation potential and costs of various technologies were evaluated, including thermal conversion, anaerobic digestion, hydrothermal processes, and wet oxidation. These technologies offer GHG emission reductions ranging from 0.09 to 0.46 t CO2-eq/t dry solids compared to conventional methods, while also promoting resource recovery and circular economy principles. However, further optimization is necessary to enhance their environmental and economic performance, ensuring long-term sustainability. By implementing these technologies and adopting optimization strategies, China's sludge treatment industry can significantly contribute to achieving the country's carbon neutrality goal and fostering sustainable development.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

Efficient gene transfer and expression tool is lacking for shrimps and shrimp cells. To solve this, this study has developed a shrimp DNA virus-mediated gene transfer and expression system, consisting of insect Sf9 cells for viral packaging, shrimp viral vector of pUC19-IHHNV-PH-GUS and baculoviral vector of Bacmid or Bacmid-VP28 encoding shrimp WSSV envelope protein VP28. The pUC19-IHHNV-PH-GUS vector was constructed by assembling the genomic DNA of shrimp infectious hypodermal and hematopoietic necrosis virus (IHHNV), which had shortened inverted terminal repeats, into pUC19 backbone, and then an expression cassette of baculoviral polyhedron (PH) promoter-driven GUS reporter gene was inserted immediately downstream of IHHNV for proof-of-concept. It was found that the viral vector of pUC19-IHHNV-PH-GUS could be successfully packaged into IHHNV-like infective virions in the Sf9 cells, and gene transfer efficiency of this system had been evaluated and verified in three systems of Sf9 cells, shrimp hemolymph cells and tissues of infected shrimps, but GUS expression could be detected only in the cases when the viral vector was co-transfected or co-infected with a baculovirus of Bacmid or Bacmid-VP28 due to the Bacmid-dependence of PH promoter. Moreover, the packaging and infection efficiencies could be significantly improved when Bacmid-VP28 was used instead of Bacmid.

Histones are keys to many epigenetic events and their complexes have therapeutic and diagnostic importance. The determination of the structures of histone complexes is fundamental in the design of new drugs. Computational molecular docking is widely used for the prediction of target-ligand complexes. Large, linear peptides like the tail regions of histones are challenging ligands for docking due to their large conformational flexibility, extensive hydration, and weak interactions with the shallow binding pockets of their reader proteins. Thus, fast docking methods often fail to produce complex structures of such peptide ligands at a level appropriate for drug design. To answer this challenge, and improve the structural quality of the docked complexes, post-docking refinement has been applied using various molecular dynamics (MD) approaches. However, a final consensus has not been reached on the desired MD refinement protocol. In the present study, MD refinement strategies were systematically explored on a set of problematic complexes of histone peptide ligands with relatively large errors in their docked geometries. Six protocols were compared that differ in their MD simulation parameters. In all cases, pre-MD hydration of the complex interface regions was applied to avoid the unwanted presence of empty cavities. The best-performing protocol achieved a median of 32 % improvement over the docked structures in terms of the change of root mean squared deviations from the experimental references. The influence of structural factors and explicit hydration on the performance of post-docking MD refinements was also discussed to help their implementation in future methods and applications.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Improper illumination of cultural heritage buildings and monuments can be a source of enormous light pollution that can have a major impact on the overall environment of the illuminated area. Such lighting can be the result of carelessness or a wrong/badly designed lighting system. This paper presents one of the methodologies that can significantly reduce light pollution, especially the spilt light out of the façade. The methodology is based on using luminaires with specially made shutters with the appropriate silhouette of the object. The shutter is planned with the help of an object photo and sizes measured at the location. The methodology was tested during the renovation of the lighting system of different churches in Slovenia and is described in the example of the Church of St. Thomas near Ptuj, Slovenia. The results showed that the methodology is effective and can significantly reduce light pollution that occurs when such buildings are incorrectly lit.

In the Internet of Things (IoT) era, Mobile Edge Computing (MEC) significantly enhances the efficiency of smart devices but is limited by battery life issues. Wireless Power Transfer (WPT) addresses this issue by providing a stable energy supply. However, effectively managing overall energy consumption remains a critical and under-addressed aspect for ensuring the network’s sustainable operation and growth. In this paper, we consider a WPT-MEC network wit user cooperation to migrate the double near-far effect for the mobile node (MD) far from the base station. We formulate the problem of maximizing long-term computation rates under a power consumption constraint as a multi-stage stochastic optimization (MSSO) problem. This approach is tailored for a sustainable WPT-MEC network, considering the dynamic and varying MEC network environment, including randomness in task arrivals and fluctuating channels. We introduce a virtual queue to transform the time-average energy constraint into a queue stability problem. Using the Lyapunov optimization technique, we decouple the stochastic optimization problem into a deterministic problem for each time slot, which can be further transformed into a convex problem and solved efficiently. Our proposed algorithm works efficiently online without requiring further system information. Rigorous mathematical analysis shows that our algorithm achieves O(1/V),O(V) trade-off between computation rate and queues stability. Extensive simulation results demonstrate that our proposed algorithm outperforms baseline schemes, achieving approximately 4% enhancement while maintain the queues stability.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

With the rapid growth of large language models (LLMs), there is increasing demand for memory and computation in LLMs. Recent efforts on post-training pruning of LLMs aim to reduce the model size and computation requirements, yet the performance is still sub-optimal. In this paper, we present a plug-and-play solution for post-training pruning of LLMs. The proposed solution has two innovative components: 1) Relative Importance and Activations (RIA), a new pruning metric that jointly considers the weight and activations efficiently on LLMs; and 2) Channel Permutation, a new approach to maximally preserve important weights under N:M sparsity. The two proposed components can be readily combined to further enhance the N:M semi-structured pruning of LLMs. Our empirical experiments show that RIA alone can already surpass all existing post-training pruning methods on prevalent LLMs, e.g., LLaMA ranging from 7B to 65B. Furthermore, N:M semi-structured pruning with channel permutation can even outperform the original LLaMA2-70B on zero-shot tasks, together with practical speed-up on specific hardware. Our code is available at: https://github.com/biomedical-cybernetics/Relative-importance-and-activation-pruning

In recent years, architectural interactions have become the center of many important reflections. However, there is little agreement on the subject. Some authors consider architecture to be about its relations with human and nonhuman agents. Others consider that buildings have an autonomous presence, which transcends all their interactions. These approaches are generally seen as incompatible. Although at the heart of the debate is the role of relations in architecture, their nature is not addressed. The discussion could gain clarity by recognizing the differences between them. In this paper, we propose a classification of architectural interactions, which may help to better inform further discussion on the topic. A closer look at architectural relations reveals that autonomy and relationality are not opposing, but complementary aspects.

The Double Diaphragm Forming (DDF) process uses vacuum pressure and heat to pre-shape composite reinforcements between flexible diaphragms. Accurate modelling of heat transfer within DDF requires knowledge of the thermophysical properties of the constituent materials. This study investigates the specific heat and thermal conductivity of silicone diaphragms, carbon fibers (chopped and powdered), thermoplastic veils, and their combinations. Experiments measured the specific heat of each material using differential scanning calorimetry and the thermal conductivity of silicone and carbon fabric preforms using the transient plane source method and modified transient plane source method respectively. The influence of reheating cycles on specific heat of carbon fiber-veil samples and the effect of compaction on thermal conductivity of silicone and carbon fabrics were explored. While silicone exhibited linear specific heat behavior, the thermoplastic veil showed non-linearity due to phase change. The combined carbon fiber-veil samples demonstrated slight non-linear specific heat variations depending on reheating cycles. Thermal conductivity of the fabric preforms decreased with the addition of thermoplastic veil and under vacuum-compaction conditions. The established temperature-dependent property relationships provide valuable data for optimizing DDF preforming parameters and enhancing energy efficiency in composite manufacturing.

This comprehensive critical review shows how green buildings and energy optimization solutions improve indoor air quality as well as environmental quality (IEQ) and human health. Electricity-efficient green buildings create a better indoor atmosphere and save electricity. Green buildings improve occupant well-being through IAQ, thermal comfort, acoustics, and lighting. Renewable energy, green construction materials, and intelligent technologies increase sustainability and reduce environmental impact. Environmental hazards, architectural design, and societal variables can improve indoor air quality and subsequently reduce health risks linked with poor air quality. The evaluation highlights the pros and cons of low-cost IAQ sensors and equipment. These devices provide valuable insights, but calibration and validation using reference equipment are necessary to ensure accuracy and reliability. Architects, engineers, environmentalists, and policymakers are essential in creating green buildings with high IEQ. Prioritizing occupant comfort, health, and productivity ensures a sustainable and healthy future for future generations. However, continual monitoring and research are needed to improve green building practices and overcome construction problems. Intelligent models for continual on-field calibration of low-cost sensors may improve performance. Green buildings benefit occupants and the environment by optimizing energy use and using IAQ monitoring technologies.

Abstract: Seismic performance and loss assessments can have widely varying degrees of uncertainty. An essential issue is whether a particular assessed seismic loss or performance result has sufficient reliability to serve as the basis for risk management decisions and actions, including whether or not a code prescribed performance level is met, or if an assessed loss level is acceptable. A method is developed measuring the reliability of performance and loss assessments for individual buildings and for portfolios. Consideration is given to how well the building investigation and corresponding evaluation process have been performed, the qualifications of the person(s) doing the assessment, the thoroughness of the evaluation, and the technical validity of the assessment procedure or model. The approach characterizes the uncertainty of each component of the assessment procedure for each building in qualitative terms. The resulting reliability measure is likely to be most useful for the cases where an entity is determining whether/or not a building has acceptable life safety performance, or if a portfolio has an acceptably low risk of seismic damage loss over a given period of time. In both cases, the reliability must either be sufficient to warrant action, or serve to indicate need for improved assessment.

Only now, four decades after passive houses were designed in the US and built in Canada, the authors are able to discuss the next generation of new and retrofitted buildings in the same way. This paper presents a universal system for different types of buildings and climates that includes construction experience and is reinforcing multi-disciplinary synergies. A next generation of technology uses adaptable indoor climate, integrates HVAC and building structure; applies field monitoring of energy and indoor environment and develops a performance model that is based on artificial neutral network. This approach, includes: 1. The self-learning ANN as a part of the building management system, 2. This management system guides energy optimization in a post-construction stage 3. A two-stage construction process for new and retrofits. The first stage prescribes investment level and optimizes performance; opposite in the second stage. This paper highlights that some elements of the proposed methodology have already been applied in the practice. It also underlines that this integrated multi-disciplinary system can be applied with a different combination of technological elements.

Lead-acid batteries utilised in electrical substations release hydrogen and oxygen when these are charged. These gases could be dangerous and cause a risk of fire if they are not properly ventilated. Therefore, this research seeks to design and implement a network control panel for heating, ventilation, and air-conditioning systems (HVACS). This is done using a specific range of controllers, which have more than thirty loops of proportional, integral and derivative (PID) control to achieve a cost-effective design. It performs the required function of extracting hydrogen, oxygen, and maintaining the desired temperature of the battery storage room within the recommended limits (i.e. 25°C ±1°C tolerance) without compromising quality as set out in the user requirement specification in Appendix-A. The system control panel allows the user to access control parameters such as changing temperature set-points, fan-speed, sensor database amongst others. The hardware is configured to detect extreme hydrogen and oxygen gas content in the battery room and ensure that the HVACS extract the gas content to the outside environment. The results of the system show that the network control panel effectively operates as per the recommended system requirements. Therefore, the effective operation of the HVACS ensures sufficient gas ventilation, thus mitigating the risk of fire in a typical battery storage room. Furthermore, the effective operation of HVACS enhances battery lifespan because of regulated operating temperature, which is conducive to minimise the effect of sulfation in lead acid Batteries (LABs).

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

Cloud data centers play a vital role in modern computing infrastructure, offering scalable resources for diverse applications. However, managing costs and resources efficiently in these centers has become a crucial concern due to the exponential growth of cloud computing. User applications exhibit complex behavior, leading to fluctuations in system performance and increased power usage. To tackle these obstacles, we propose the consolidation of virtual machines (VMs) to optimize resource utilization and reduce operational costs. This paper introduces a novel algorithm, leveraging the Modified Artificial Feeding Birds Algorithm (ModAFBA), to manage cost optimally in cloud data centers by reducing power usage while meeting service level agreements (SLAs). The ModAFBA algorithm, inspired by bird foraging behavior, dynamically adjusts solutions based on environmental changes. Comprehensive experimental evaluation demonstrates the superiority of the proposed algorithm in terms of power usage, migration count, and SLA compliance. Through this research, we aim to advance cost management and resource optimization in cloud data centers, providing a valuable tool for cloud service providers to enhance infrastructure efficiency and achieve cost savings.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

Buildings can generate heats which are mostly generated from the machinery using inside the buildings, and these heats generally released to the atmosphere. Buildings can also block the wind flow by their canopies and trap the heat by using low albedo materials. These causes pointedly contribute to urban heat island and greenhouse effects. Likewise, urban development and building construction in Cambodia are growing rapidly. The construction has been recognized as a key development sector while thousands of buildings are being built and have been operated in the main cities. However, those buildings mostly have not been considered to incorporate sustainability concepts while the major final energy consumers in the country are buildings. The buildings’ energy consumption is also projected to increase more than double until 2040. Hence, sustainable building promotion in Cambodia is necessary, and sustainable building criteria are completely required. This research aims to find out significant sustainable building criteria for Cambodia and focused on planning and design criteria because having proper planning and design is a smart start leading to achieving building sustainability in all stages. This research used the Delphi methods to validate the relevant sustainable building criteria available in the literature and then select the significant ones for Cambodia based on the Delphi consensus. The results showed that ninety-nine consensus planning and design criteria were found to be significant for sustainable buildings in Cambodia.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

The second article in the series presents the application of the Smoothed Particle Hydrodynamics (SPH) method to modelling of batch crystallisation in stirred tanks. A methodology to integrate the population balance equations (PBE) in parallel and independently from the Navier-Stokes equations is demonstrated. The benefits of the proposed methodology in terms of computational requirements, accuracy and availability of the crystal size distribution are discussed. The specific formulation of the SPH equations where the resulting system of ordinary differential equations is solved using the weighted contributions rather than numerically by solving a linear system of equations allows for massive parallelisation and a very loose coupling of the population balance and the fluid dynamics. It has been demonstrated, that the population balance equations can be solved on a Shared Memory Architecture (SMA) system using the OpenMP interface while the fluid dynamics equations being computed independently on a General Purpose Graphics Processing Unit (GPGPU) using the NVidia CUDA technology. This way, a significant portion of the computational overhead due to the large number of additional transport equations resulting from the discretisation of the population balance was removed: the SPH simulation coupled with 200 population balance equations was only 40% slower compared to SPH-only simulation. Two methods for the solution of population balance equations that preserve full crystal size distribution were implemented: discretised population balance (DPB) and method of characteristics (MOCH). The DPB equations are solved using the high-resolution finite-volume method with flux limiter and the effect of a large number of different flux limiters have been investigated. Both methods were validated using the case studies from the literature where an analytical solution can be derived. The developed models were applied to a numerical solution of coupled computational fluid dynamics and population balance equations to model a batch crystallization process. The effect of the hydrodynamics on the local temperature/supersaturation and the resulting crystal size distribution was captured and compared to the ideal mixing case. The simulation results from the DPB and MOCH methods were compared in terms of computational requirements and accuracy and MOCH selected as computationally more efficient and accurate.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

In this work, we report the synthesis of a new thiosemicarbazone-based drug of N'-(di(pyridin-2-yl)methylene)-4-(thiazol-2-yl)piperazine-1-carbothiohydrazide (HL) featuring a thiazole spectator for the efficient coordination with Cu(II) to give [CuCl(L)]2 (1) and [Cu(NO3)(L)]2 (2). Both 1 and 2 exhibit dimeric structures ascribed to the presence of di-2-pyridylketone moieties that demonstrate dual functions of chelation and intermolecular bridging. HL, 1 and 2 are highly toxic against hepatocellular carcinoma cell lines Hep-G2, PLC/PRF/5, and HuH-7, with half maximal inhibitory concentration (IC50) values as low as 3.26 nmol/mL (HL), 2.18 nmol/mL (1), and 2.54 × 10−5 nmol/mL (2) for PLC/PRF/5. While the free ligand HL may elicit its anticancer effect via sequestration of bio-relevant metal ions (i.e. Fe3+ and Cu2+), 1 and 2 are also capable of generating cytotoxic reactive oxygen species (ROS) to inhibit cancer cell proliferation. Our preliminary pharmacokinetic studies revealed that oral administration (per os, PO) of HL has a significantly longer half-life t1/2 of 21.61 ± 9.4 h, nearly doubled as compared to that of the intravenous (i.v.) administration of 11.88 ± 1.66 h, certifying HL as an effective chemotherapeutic drug via PO administration.

A typical orchard's mechanical operation consists of three or four stages: lining, digging for plantation, moving the seedling from nurseries to the farm, moving the seedling to the planting hole, and planting the seedling in the hole. However, the digging the planting hole is the most time-consuming operation. In fruit orchards, robots' usage is increasingly becoming more prevalent to increase operational efficiency. They offer practical and effective services to both industry and people, whether they are assigned to plant trees, reduce the use of chemical fertilizers, or carry heavy loads to relieve staff. Robots can operate for extended periods of time and can highly adept at repetitive tasks like planting many trees. The present study aims to identify the locations for planting trees in orchards using geographic information systems (GIS), to develop an autonomous drilling machine and use the developed robot to open planting holes. There isn't a comparable study on autonomous hole planting in the literature in this regard. The agricultural mobile robot is a four wheeled nonholonomic robot with differential steering and forwarding capability to stable target positions. The designed mobile robot can be used in fully autonomous, partially autonomous, or fully manual modes. The drilling system, which is a y-axis shifter driven by a DC motor with reducer includes an auger with a 2.1 HP gasoline engine. SOLIDWORKS software was used for designing and drawing of the mobile robot and drilling system. The Microsoft Visual Basic.NET programming language was used to create the robot navigation system and drilling mechanism software. The cross-track error (XTE), which determines the distances between the actual and desired holes positions, was utilized to analyze the steering accuracy of the mobile robot to the drilling spots. Consequently, the average of the arithmetic means was determined to be 4.35 cm, and the standard deviation was 1.73 cm. This figure indicates that the suggested system is effective for drilling plant holes in orchards.

Driven by the proliferation of DC energy sources and DC end-use devices (e.g., photovoltaics, battery storage, solid-state lighting, and consumer electronics), DC power distribution in buildings has recently emerged as a path to improved efficiency, resilience, and cost savings in the transitioning building sector. Despite these important benefits, there are several technological and market barriers impeding the development of DC distribution, which have kept this technology at the demonstration phase. This paper identifies specific end-use cases for which DC distribution in buildings is viable today. We evaluate their technology and market readiness, as well as their efficiency, cost, and resiliency benefits while addressing implementation barriers. The paper starts with a technology review, followed by a comprehensive market assessment, in which we analyze DC distribution field deployments and their end-use characteristics. We also conduct a survey of DC power and building professionals through on-site visits and phone interviews and summarize lessons learned and recommendations. In addition, the paper includes a novel efficiency analysis, in which we quantify energy savings from DC distribution for different end-use categories. Based on our findings, we present specific adoption pathways for DC in buildings that can be implemented today, and for each pathway we identify challenges and offer recommendations for the research and building community.

As fossil-fueled heating in the building sector is responsible for 16 % of Germanys total CO2 emissions, it is of great importance to use climate-neutral alternatives for the decarbonization of this sector. Options for the climate-neutral heating of buildings include electricity or hydrogen as energy carriers, both explicitly considered by German policy. In this paper, bottom-up studies are conducted to investigate the role of hydrogen for the climate-neutral energy supply of ten selected residential buildings in comparison to electricity-based systems. Based on a selection of as different typical buildings as possible for single- (SFH) and multi-family houses (MFH) of different construction years, demand profiles are simulated for each building and the respective cost-optimal supply system is determined. For the construction of this system, the electricity-based technologies available are electric heater and heat pump as well as the hydrogen-based technologies hydrogen boiler and fuel cell combined heat and power (CHP) system. Based on the results of the optimization, sensitivity analyses are performed. These analyses aim to identify threshold values of the hydrogen price for the use of hydrogen in building energy systems as well as to make the quantities of hydrogen consumed visible.The identified threshold values show the significant role of hydrogen-operated CHP in MFH if the hydrogen price reaches 0.17 €/kWh_H2 in 2050 at an electricity price of 0.31 €/kWh_el. So, hydrogen-based energy systems represent an economically viable alternative to electricity-based systems with heat pumps. We identify electricity to hydrogen price ratios for the economically viable use of hydrogen in the examined buildings that range from 1.67 to 2.82. According to these ratios, the economically reasonable use of hydrogen in buildings can be derived. For the individual building groups for the year 2050, a ratio of 2.5 can be determined for SFH and 1.8 for MFH, that is favored by the use of CHP which also supplies electricity to the buildings. However, the role hydrogen will finally play in German residential buildings in the future depends to a large extent on political decisions on distribution issues and price signals.

The urgent need to improve performance in the construction industry has led to the adoption of many innovative technologies. 3D laser scanners are amongst the leading technologies being used to capture and process assets or construction project data for use in various applications. Due to its nascent nature, many questions are still unanswered about 3D laser scanning, which in turn contribute to the slow adaptation of the technology. Some of these include the role of 3D laser scanners in capturing and processing raw construction project data. How accurate is the 3D laser scanner or point cloud data? How does laser scanning fit with other wider emerging technologies such as Building Information Modelling (BIM)? This study adopts a proof-of-concept approach, which in addition to answering the afore-mentioned questions, illustrates the application of the technology in practice. The study finds that the quality of the data, commonly referred to as point cloud data is still a major issue as it depends on the distance between the target object and 3D laser scanner’s station. Additionally, the quality of the data is still very dependent on data file sizes and the computational power of the processing machine. Lastly, the connection between laser scanning and BIM approaches is still weak as what can be done with a point cloud data model in a BIM environment is still very limited. The aforementioned findings reinforce existing views on the use of 3D laser scanners in capturing and processing construction project data.

Recently, attention mechanisms have developed into an important tool for performance improvement of deep neural networks. In computer vision, attention mechanisms are generally divided into two main branches: spatial and channel attention. Both attention categories have their own advantages. The fusion of both attentions achieves higher performance, on the cost of the computational load. This paper introduces an innovative and lighter n-shifted sigmoid channel and spatial attention (CSA) module to reduce the computational cost and to improve the 3D scene relevant features selection. To validate the proposed attention module, 3D scene object detection in the deep Hough voting point sets is considered as the testing application. The proposed attention module with its piecewise n-shifted sigmoid activation function improves the network’s learning and generalization capacity which effectively predict bounding box parameters directly from 3D scenes and detect objects more accurately. This advantage is achieved by selectively attending to more relevant features of the input data. When used in the deep Hough voting point sets, the proposed attention module outperforms state-of-the-art 3D detection methods on the sizable SUNRGBD dataset. Experiments conducted showed an increase of 12.02 mean accuracy precision (mAP) when compared to the celebrated VoteNet (without attention). It also got 9.92 mAP higher compared to the MLVCNet, and 10.32 mAP higher than the Point Transformer. The proposed model not only decreases the sigmoid vanishing gradient problem but also brings out valuable features by fusing channel-wise and spatial information while improving accuracy results in 3D object detection.

For the majority of the contractual arrangements used in construction projects, the owner is not responsible for the cost deviations due to the variability of labor productivity or material price, amongst many other aspects. Consequently, the cost performance of a project may be entirely distinct for the owner and the contractor. Since the majority of the quantitative research on cost estimation and deviation found in the literature adopts the owners’ perspective, this research provides a contribution towards modelling costs and cost deviation from a contractors’ perspective. From an initial sample of 13 residential building and 10 office building projects, it was possible to develop models for cost estimation at the early stage of development including both endogenous and exogenous variables. Although the sample is relatively small, the authors were able to fully analyze all the cost data, using no secondary sources of data (very frequent in cost modelling studies). The statistically significant variables in the cost estimation models were the areas above and below ground and the years following the 2008 financial crisis, including the international bailout (2011-2014) period. For estimating the unit cost, a nonlinear model was obtained with the number of underground and total floor, the floor ratio and the years following the 2008 financial crisis, including the international bailout (2011-2014) period as predictors. For the office buildings, it was also found a statistically significant correlation between the cost deviation and the number of underground floors.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

A machine learning method for classifying Lung UltraSound is here proposed to pro- vide a point of care tool for supporting a safe, fast and accurate diagnosis, that can also be useful during a pandemic like as SARS-CoV-2. Given the advantages (e.g. safety, rapidity, portability, cost-effectiveness) provided by the ultrasound technology over other methods (e.g. X-ray, computer tomography, magnetic resonance imaging), our method was validated on the largest LUS public dataset. Focusing on both accuracy and efficiency, our solution is based on an efficient adaptive ensembling of two EfficientNet-b0 models reaching 100% of accuracy, which, to our knowledge, outperforms the previous state-of-the-art. The complexity of this solution keeps the number of parameters in the same order as an EfficientNet-b0 by adopting specific design choices that are adaptive ensembling with a combination layer, ensembling performed on the deep features, minimal ensemble only two weak models. Moreover, a visual analysis of the saliency maps on sample images of all the classes of the dataset reveals where the focus is on an inaccurate weak model versus an accurate model.

An event occurring within a stationary environment, in the direction toward which an observer self-rotates, is perceived to precede a simultaneous event, in the direction away from which she moves. When self-rotation results from angular acceleration in the dark, perception of space is also distorted, such that the subjective straight-ahead shifts in the opposite direction to motion and temporal event promotion. A reference frameshift theory, based on the special theory of relativity, is proposed to explain these findings. Here, a hyperbolic tangent transformation of objective angular velocity constrains subjective self-rotation velocity within finite bounds, consistent with it being a limited perceptual resource. Identifying this subjective variable with vestibular nystagmus slow-phase angular velocity, the asymptotic perceived self-rotation velocity is estimated at ~200 °⁄s. When included in the Lorentz transformations of the new formalism, this value predicts experimental simultaneity distortion. Hypothetically, the hyperbolic tangent objective-to-subjective transfer function would maximize the differential entropy of the percept, and thereby also the stimulus/percept mutual information, if angular velocities of body rotation encountered in naturalistic environmental interaction have a logistic probability density distribution of scale 100 °⁄s, a proposed experimental test of the scheme.

Stagnating low renovation rates, vacancies and underused town centers, unprecedentedly high levels of land sealing and excessive consumption of resources through the construction of new buildings and infrastructure as well as the effects of climate change were some of the reasons for carrying out the monumentum ad usum research project.Thermodynamic simulations were used to carry out in-depth analyses of specific building parameters such as energy balances and how they are influenced by the effects of climate change. Life cycle analyses under ecological and economic aspects examined the aspects of sustainability and the individual behaviour of predominantly listed existing buildings under standardized conditions.The project results show that sustainable refurbishment can significantly increase the attractiveness of using historic and listed buildings for non-profit building owners. The results and conclusions of the project are as varied as the recommendations derived from them. In practice, old buildings consume significantly less energy than predicted in the structural calculations. Correction factors are to be developed and thermodynamic simulation calculations are to be used instead of energy performance certificates for more realistic forecasts of energy requirements and emission savings potential. The aspects of sustainability in refurbishment are essential for the protection of our architectural heritage.

Advances towards smart ecosystems showcases Internet of Things (IoT) as a transversal strategy to improve energy efficiency in buildings, to enhance their comfort and environmental conditions, and to grow knowledge about building behavior, its relationships with the users and the interconnections among themselves and with the environmental and ecological context. EU estimates that 75% of the building stock is inefficient and aged with +40 years old. Although many buildings have some kind of system for regulating their indoor temperature, only a small subset provides integrated Heating, Ventilation, and Air Conditioning (HVAC) systems; within that subset, only a low percentage includes smart sensors, and only a minimum of that percentage integrates those sensors into IoT ecosystems. This work proposes several contributions. On the one hand, to understand the built environment as a set of interconnected systems that constitute a complex framework where IoT ecosystems are key enabling technologies to improve energy efficiency and Indoor Air Quality (IAQ) by filling the gap between theoretical simulations and real measurements. On the other hand, to understand IoT ecosystems as cost-effective solutions where: acquire data through connected sensors, analyze information in real-time, and build knowledge to make data-driven decisions. Furthermore, data set is public for third-party use to contribute scientific community to their research studies. Thus, this paper also contributes with a detailed functional scheme of IoT ecosystem deployed in 3 buildings of University of Zaragoza (Spain) with +200 geolocated wireless sensors with +100 representative spaces. The obtained results, through real installations with IoT as learning factory, show several learned lessons (about building complexity; energy consumption, costs and savings; and IAQ and health improvement) and contribute, as a proof-of-concept, with a proposal of prediction of building performance based on both correlations (between CO2 and occupancy) and neural networks (applied to CO2 and temperature). In summary, in a real context of economic restrictions, complexity, higher energy costs, social vulnerability and climate change, IoT-based strategies, as proposed in this work, highlight as an open, modular and interoperable approach to move towards smart communities (buildings, cities, regions, etc.) by improving energy efficiency and environmental quality (indoor and outdoor) with low cost, quick implementation, and low impact on users within great challenges for growth, interconnection, climate change and sustainability.

The close proximity of different buildings heights can cause disturbances in the working of the smoke and ventilation ducts of lower buildings, threatening the health and even the lives of residents. To define the influence of high-rise building on the work of the ducts of the neighbouring double-storied building, experimental investigations in the wind tunnel were conducted. On this basis, empirical equations and graphs were developed leading to determining the aerodynamic coefficients considering different wind directions and the height of ducts. The direction of the wind reveals a greater influence than the height of the ducts. Properly using deflectors or increasing the height of the duct ensures maintaining static rarefaction in the area of smoke and ventilation ducts. The creation of rarefaction ensures the reliability of the natural ventilation system and the safety of the health of residents.

The natural frequency of buildings decreases during a strong-motion earthquake, and the structure loses its stiffness. As a result, understanding the damaging process in the structure owing to changes in structural properties is critical during a seismic excitation. The time-frequency technique can detect the damaged building’s time-varying frequency contents. Wigner distributions (WD), Wigner-Ville distributions (WVD), pseudo-Wigner-Ville distributions (PWVD), smoothed pseudo-Wigner-Ville distributions (SPWVD), and synchrosqueezing transforms (SST) have all become popular in recent years for a variety of earthquake engineering applications, including building damage detection. This study proposes the local maximum synchrosqueezing transform (LMSST) for detecting frequency shifts in buildings during strong earthquakes. The data presented in the research show that the suggested method outperforms as compared to the conventional time-frequency methods for detecting frequency shifting in earthquake-damaged structures.

The construction of earth buildings, both throughout history and in the current day, is well-established worldwide. Despite New Zealand's pre- and post-colonial history of earth construction, earth buildings as residential homes have not been well-received or popularised throughout present-day New Zealand. This research aims to identify the reasons for this lack of awareness and to determine methods that promote earth buildings in New Zealand. This research is based on data collected from semi-structured interviews conducted with subject matter experts and via an online questionnaire completed by members of the Earth Building Association New Zealand (EBANZ). The data collected revealed the experiences and perceptions of all participants regarding the advantages, challenges and promotion of earth buildings specific to New Zealand. Upon analysing these responses, key reoccurring themes were identified and compared. Regarding New Zealand's lack of awareness of earth buildings, interview and questionnaire participants responded that this shortcoming was due to earth construction being a very niche market and lacking commercial marketing. Education was the most frequently reoccurring theme raised by all participants as the top promotional tool for raising awareness of earth buildings. The results of this research can be applied to future work regarding obstacles that limit the growth of New Zealand's earth building industry, as well as research on the role of New Zealand's education system in exposing the next generation of builders, designers, and consumers to earth construction.

The need for a relatively quick solution to the problem of providing highways with roadside service facilities necessitates the development of a series of appropriate standard projects. To increase the efficiency of these series, it is advisable to carry out the interconnection of space-planning solutions based on a particular module. Taking into account the variety of planning and landscape characteristics of the sites for the placement of objects of the mainline service, it seems advisable to choose as a module not a square or rectangular, but a triangular configuration, which allows in most cases to harmoniously block the modules. The proposed roof module in the form of a "regular" triangle facing the tetrahedron has a structural basis in the form of a single-tier rod spatial plate. The principal space-planning solutions of all four dozen objects from the approved nomenclature of the mainline service performed in the process of analyzing the possibilities show the real possibility of solving the development tasks on the basis of this system. The use of the proposed modular system makes it possible to successfully solve a number of tasks to reduce the harmful impact on the environment and effectively use renewable energy sources.

Earthquake is among the most devastating natural disasters causing severe economic, environmental, and social destruction. Earthquake safety assessment and building hazard monitoring can highly contribute to urban sustainable development through identification and insight into optimum materials and structures. While the vulnerability of structures mainly depends on the structural resistance, the safety assessment of buildings can be highly challenging. In this paper, we consider Rapid Visual Screening (RVS) method which is a qualitative procedure for estimating structural scores for buildings suitable for medium- to high-seismic cases. This paper presents an overview of the common RVS methods, i.e., FEMA P-154, IITK-GGSDMA, and EMPI. To examine the accuracy and validation, a practical comparison is performed between their assessment and observed damage of reinforced concrete buildings from a street survey in the Bingöl region, Turkey, after the 11 May 2003 earthquake. The results demonstrate that the application of RVS methods for preliminary damage estimation is a vital tool. Furthermore, the comparative analysis showed that FEMA P-154 creates an assessment that overestimates damage states and is not economically viable while EMPI and IITK-GGSDMA provide for more accurate and practical estimation, respectively.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

This paper provides a review of an emerging field in the food processing sector, referring to efficient and safe food supply chains, ’from farm to fork’, as enabled by Artificial Intelligence (AI). Recent advances in machine and deep learning are used for effective food production, energy management and food labeling. Appropriate deep neural architectures are adopted and used for this purpose, including Fully Convolutional Networks, Long Short-Term Memories and Recurrent Neural Networks, Auto-Encoders and Attention mechanisms, Latent Variable extraction and clustering, as well as Domain Adaptation. Three experimental studies are presented, illustrating the ability of these AI methodologies to produce state-of-the-art performance in the whole food supply chain. In particular, these concern: (i) predicting plant growth and tomato yield in greenhouses, thus matching food production to market needs and reducing food waste or food unavailability; (ii) optimizing energy consumption across large networks of food retail refrigeration systems, through optimal selection of systems that can get shut-down and through prediction of the respective food de-freezing times, during peaks of power demand load; (iii) optical recognition and verification of food consumption expiry date in automatic inspection of retail packaged food, thus ensuring safety of food and people’s health.

Nonparametric assessments of police technical and scale efficiency is challenging because of the stochastic nature of criminal behavior and because of the subjective dependence on multiple decision criteria, which can lead to a more or less efficiency prospect depending on the regulation, necessity, or organizational objective. There is a trade-off between efficiency and effectiveness in many police performance assessments, i.e., efficient departments (producing more clear-ups with a given resource) are crime-specialized or cannot reproduce those good results effectively on more severe or complex occurrences. This study proposes a combined methodology for carrying out efficiency and effectiveness analysis of Police departments. A conditional non-parametric approach, which allows to include crime as an external factor in the analysis, is combined with a non-compensatory ranking based on the PROMETHEE II methodology for the approach illustrated on the multidimensional efficiency and effectiveness comparison of 145 Pernambuco (Brazil)'s police departments. The application results offer compelling perspectives for public administrations concerning the strategic prioritization of units for rewards or interventions.

Smart home and building systems are popular solution that support maintaining comfort, safety and improving energy efficiency in buildings. However, dynamically developing distributed network technologies, in particular the Internet of Things, are increasingly entering the above-mentioned application areas of building automation, offering new functional possibilities. The result of these processes is the emergence of many different solutions that mix technologies of field-level and ICT networks in various configurations and architectures. New paradigms are also emerging, such as edge and fog computing, providing support for local monitoring and control networks in the implementation of advanced functions and algorithms, including machine learning and artificial intelligence mechanisms. This paper collects state-of-the-art information in these areas, along with a systematic review of the literature, case-studies and an analysis of selected development trends. The author systematized this information in the context of the potential development of building automation systems. Based on the conclusions of this analysis and discussion, a framework for the development of the Generic IoT paradigm in smart home and building applications has been proposed, along with a SWOT analysis of its usability. Future works are proposed as well.

This study addresses the formidable challenge of solving large-scale Max-Cut problems (MCP). We introduce a rapid computational procedure utilizing a hybrid 1-flip/r-flip local search heuristic. This innovative strategy significantly reduces the computational time required for MCP problems while consistently generating solutions of exceptional quality. The paper presents substantial computational insights, showcasing the effectiveness of our approach on large-scale Max-Cut instances with varying densities. Our proposed heuristic is rigorously evaluated by comparing its performance against a quantum annealing solver, leveraging a multi-start Tabu Search framework. The results underscore the potency of this unique combination as an efficient and effective solution for large-scale QUBO problems. Notably, our hybrid heuristic consistently delivers high-quality solutions within the stringent CPU time limits of 600 seconds, demonstrating its efficacy across Max-Cut instances ranging from 10,000 to 40,000 variables. This research contributes to advancing the state-of-the-art in large-scale QUBO problem-solving, offering a powerful and time-efficient approach with broad applicability.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

3D city models integrate heterogeneous urban data from multiple sources in a unified geospatial representation, combining both semantics and geometry. Although in the last decades, they are predominantly used for visualization, today they are used in a large range of tasks related to exploration, analysis, and management across multiple domains. The complexity of urban processes and the diversity of urban environment bring challenges to the implementation of 3D city models. To address such challenges, this paper presents the development process of a 3D city model of a single neighborhood in Sofia city based on CityGML 2.0 standard. The model represents the buildings in LOD1 with a focus on CityGML features of related to the buildings like building part, terrain intersection curve and address. Similar building models of 18 cities provided as open datasets are explored and compared in order to extract good modeling practices. As a result, workflows for generation of 3D building models in LOD1 are elaborated and improvements in the feature modeling are proposed. Two options of building model are examined: modeling of a building as a single solid and modeling of a building with separate building parts. Finally, the possibilities for visualization of the model in popular platforms such as ArcGIS Pro and Cesium Ion are explored.

The UK Government is committed to reducing greenhouse gas (GHG) emissions by 80% by 2050. Buildings are responsible for 37% of the total GHG emissions in the UK and the need to reduce their emissions has resulted in more stringent building regulations in the recent past. The regulations, energy rating systems and voluntary guidelines — all are primarily aimed at reducing the need for heating and associated energy use by increasing insulation and air-tightness. However, future climates are projected to be warmer than the present day. Internal gains dominated non-domestic buildings will likely overheat, the adaptation to which will require energy-intensive cooling solutions, thus defeating the purpose of heating-focused regulations. This research investigated the effects of warming climate on overheating, and energy use and resulting emissions in representative urban office spaces in London in the present-day and future climates using hourly dynamic thermal simulations. Findings suggest that more airtight and highly—insulated office buildings designed for heating—dominated temperate UK climate will overheat in the 2050s. Heating demand reduces but electricity consumption increases by 121% when hybrid cooling is adopted to ameliorate overheating. Despite the rise, adopting a mixed-mode ventilation strategy was one of the ways of achieving overall energy efficiency while meeting benchmark overheating and carbon emissions target in present and future climatic contradictions. Current heating-focused legislations need to be urgently re-evaluated to account for the effects of climatic variability and overheating risks.

We explores the relational, dynamic elements of Complex Buildings, a type of architecture designed to incubate uses, located in urban areas with high housing density. The uses of Complex Buildings concern different elements, including the network of agents using or managing them, the environment, and the activities and functions that take place occasionally, temporarily or permanently. Data was gathered through ethnographic research lasting 6 months and a chronotopian approach was used to describe time and space. We analyzed and discussed the interaction of the elements of Complex Buildings through a cellular automaton model, a computational method that simulates the growth of complex systems. It was used here to generate patterns that suggest configurations of uses that can optimize management and therefore increase economic and social capital. The cellular automaton model was also used to develop an abstraction of the Centquatre, a public cultural center in Paris. This center is a good example of a Complex Building, being based on a public-private partnership and having an architectural configuration designed to host a wide range of art, social and productive activities. The building includes a large central space used as an urban public area open to different types of people. The importance of this case study lies in its capacity to produce economic value by combining different uses, and also by welcoming different people to the public space. Regarding the building as a living organism, the cellular automaton model reveals the determinant nature of the concepts of configuration, compatibility of uses and economic value generated by the presence of people. We argue that this approach makes it possible to show that the space-time design and public space dimensions are determinant factors in Complex Buildings.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

The rise in IoT (Internet of Things) devices poses a significant security challenge. Maintaining privacy and ensuring anonymity within the system is a sought-after feature with inevitable trade-offs, such as scalability and increased complexity, making it incredibly challenging to handle. To tackle this, we introduce our proposed work for managing IoT devices using Hyperledger fabric. We integrated our system on the blockchain with a closed-circuit television (CCTV) security camera fixed at a rental property. The CCTV security camera redirects its feed whenever a new renter walks in. We have introduced the web token for authentication from the renter to the owner. Our contributions include the proposition of efficient framework architecture, a novel chain code algorithm, and stealth addresses with modified ring signatures. We performed different analyses to show the system's throughput and latency through stress testing. We have shown the advantages of the proposed architectures by comparing similar existing schemes. Our proposed scheme enhances the security of blockchain-enabled IoT devices and mitigates the single point of failure issue. Our future work includes scaling it up to cater to the needs of the healthcare system.

Building energy demand impacts a myriad of interconnected economic, societal, and environmental aspects. As a result, Buildings Energy Models (BEM) play an important role in the process of urban design and planning. While previous studies have investigated the effects of building interventions on energy efficiency, their applicability may be limited due to the BEM’s high computational complexity. This limits their ability to systematically study important aspects of energy demand on a large scale. The development of Machine Learning Models (MLM) allows to design the required detailed analysis and solutions, while reducing the computational burden, making MLM attractive for urban designers. The capability of MLM to generalize well for multiple contexts (in our case, multiple buildings) is a crucial contributor to their applicability. However, the validation process in a wider context is often overlooked, therefore its generalization capabilities are not quantified. In this paper, we present a framework to train and validate a surrogate model derived from a physics-based BEM. Our method employs a Multiple Linear Regression model to predict Energy Use Intensity (EUI) for office buildings in Singapore using 36 input parameters (covariates), based on a training dataset of 23,000 samples. Model validation is performed by comparing the results of the Surrogate Model (SM) to a widely used BEM for a sample of 120 buildings. Our results indicate that the SM has an accuracy of NRMSE of 13%, NMBE of −3.56%, and R2 of 0.92, which suggests it can effectively and accurately predict building EUI. We also conduct a sensitivity analysis, which indicates that the parameters associated with internal loads and internal space usage are the most influential. Additionally, we present a reduced order model trained with only the 11 most influential parameters, which exhibits negligible loss in accuracy compared to the full SM while providing reduced complexity. Finally, we demonstrate an application of our SM to evaluate energy efficiency under uncertainty scenarios. The analytically derived results indicate a potential reduction of EUI of offices in Singapore from 227kWh/m2 to 99kWh/m2 by altering the building parameters that were identified as most influential.

This paper studies the dynamic response of corner supported modular steel buildings with a core wall system, under progressive collapse scenarios, associated with corner module removals. Since using secondary systems such as concrete core in mid- to high-rise buildings is currently una-voidable, understanding their impact on load transfer between modules during collapse scenarios becomes essential. The designated buildings with four-, eight- and twelve-story were modelled using the macro-model based finite element method in Abaqus. Also, three different locations are considered for the concrete shear core within the building plan, leading to nine various case scenarios. Each vertical and horizontal inter-module connection was modelled by one axial and two shear springs with predefined nonlinear force-displacement behaviour. The local and global buckling, which plays an essential role in the building's stability, was considered to obtain accurate results. Finally, parametric studies on the building response were carried out, including the intra-module connection rigidity and inter-module connection stiffness. The results demonstrated that the core wall could maintain the robustness of modular steel building through two mechanisms dependent on its location within the plan. Also, preventing plastic hinges from forming in beams could be introduced as an anti-collapse mechanism in the corner module removal scenarios

As Solar Photovoltaics in buildings reaches maturity, grid integration and economic yield are topics of greater interest. The traditional design of photovoltaic installations has considered the optimal orientation of photovoltaic modules to be that which yields the maximum annual energy production. The influence of the consumption patterns and the hourly-variable electricity prices implies that this traditional optimal design might not be the most profitable. Using a full-year dataset for a residential installation, alternative installations using canopies and modules attached to the façades are simulated. Simulating the energy balances for different annual consumptions, it is found that the canopy and façade installations offer better self-consumption of the PV produced energy, reflected in a 9% higher self-consumption degree using modules on façades and a 5% using canopies. The economic evaluation under the new electricity tariffs in Spain shows a better profit for PV self-consumption, reducing by more than 2 years the time of return on investment. The analysis of different alternatives for an industrial PV has allowed us to identify several benefits for these orientations, such as an increase in annual energy production of up to 59% over the optimal-producing orientation, that are confirmed after several months of operation.

An energy diagnosis is a tool used to seek the improvement of energy saving measures, environmental conservation and energy efficiency, making relevant its implementation in any kind of buildings. For this article, an energy diagnosis of third level was carried out in buildings of the Instituto de Energías Renovables (IER) from Universidad Nacional Autónoma de México (UNAM) through survey and census of the 36 buildings in the IER, in order to characterize current patterns of energy consumption and demand, and generating specific strategies towards savings and energy efficiency, such as indicators and corrective proposals within and non-financial investment.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

Spatial crowdsourcing emerges as a new computing paradigm that enables mobile users to accomplish spatio- temporal tasks in order to solve human-intrinsic problems. Existing crowdsourcing systems critically use centralized servers for interacting with workers and making task assignment decisions. These systems are hence susceptible to issues such as the single point of failure and the lack of operational transparency. Prior work, therefore, turns to blockchain-based decentralized crowdsourcing systems, yet still suffers from problems of lacking efficient task assignment scheme, requiring a deposit to an untrusted system, low block generation speed, and high transaction fees. To address these issues, we design a blockchain-based decentralized framework for spatial crowdsourcing, which we call SC-EOS. Our system does not rely on any trusted servers, while providing efficient and user-customizable task assignment, low monetary cost, and fast block generation. More importantly, it frees users from making a deposit into an untrusted system. Our framework can also be extended and applied to generic crowdsourcing systems. We implemented the proposed system on the EOS blockchain. Trace-driven evaluations involving real users show that our system attains the comparable task assignment performance against a clairvoyant scheme. It also achieves 10× cost savings than an Ethereum-based implementation.

A class of models for non-Gaussian spatial random fields is explored for spatial field reconstruction in environmental and sensor network monitoring. The family of models explored utilises a class of transformation functions known as the Tukey g-and-h transformations to create a family of warped spatial Gaussian process models which can support various desirable features such as flexible marginal distributions, which can be skewed, leptokurtic and/or heavy-tailed. The resulting model is widely applicable in a range of spatial field reconstruction applications. To utilise the model in applications in practice, it is important to carefully characterise the statistical properties of the Tukey g-and-h random fields. In this work, we both study the properties of the resulting warped Gaussian processes as well as using the characterising statistical properties of the warped processes to obtain flexible spatial field reconstructions. In this regard, we derive five different estimators for various important quantities often considered in spatial field reconstruction problems. These include the multi-point Minimum Mean Squared Error (MMSE) estimators; the multiple point Maximum A-Posteriori (MAP) estimators; an efficient class of multiple-point linear estimators based on the Spatial-Best Linear Unbiased (S-BLUE) estimators; and two multi-point threshold exceedance based estimators, namely the Spatial Regional and Level Exceedance estimators. Simulation results and real data examples show the benefits of using the Tukey g-and-h transformation as opposed to standard Gaussian spatial random fields in a real data application for environmental monitoring.

As urbanization continues to accelerate, the concept of smart buildings has transitioned from a futuristic vision to an integral component of modern cities. These buildings, often seen as the building blocks of smart cities, are increasingly relying on cutting-edge technologies like 5G and cloud computing to reach unprecedented levels of energy efficiency, sustainability, and occupant comfort. This paper offers a comprehensive exploration into the marriage of smart building technologies with 5G and cloud computing. It scrutinizes the individual and combined impacts of these technologies, presents various case studies showcasing real-world applications, and anticipates future trends. Moreover, it delves into technical challenges, policy implications, and offers concrete recommendations for stakeholders.

The behaviour of steel frame buildings under progressive collapse conditions depends on a combination of several parameters including the interplay between different collapse resistance mechanisms mobilized in different structural components. Previous studies have shown that the extent to which these mechanisms may contribute to progressive collapse resistance depends on the ability of the beam-column connections to undergo large inelastic deformations prior to reaching their deformation capacity limits. For this reason, and due to the important role of their flexural strength and tying capacity in the development of essential collapse resistance mechanisms, the response of beam-column connections is one of the most important features of progressive collapse performance. Based on the knowledge gained through previous studies on the mechanics of the problem, the role of the connections is critically reviewed by examining the results of several experimental studies conducted during the past decade. The factors that may adversely affect progressive collapse resistance – such as failure modes of certain connection types – are evaluated, and novel approaches of limiting these factors which are currently under development are reviewed. The assessment of these parameters leads to useful conclusions of practical significance, while highlighting the aspects of the problem that need further study and understanding.