In steel recycling, the optimization of electric arc furnaces (EAFs) is of central importance in order to increase efficiency and reduce costs. This study focuses on the optimization of electric arcs, which make a significant contribution to the energy consumption of EAFs. A three-phase equivalent circuit integrated with the Cassie-Mayr arc model is used to capture the nonlinear and dynamic characteristics of arcs, including arc breakage and ignition process. A particle swarm optimization technique is applied to real EAF data containing current and voltage measurements to estimate the parameters of the Cassie-Mayr model. A novel Arc Quality Index (AQI) is introduced in the study, which can be used to evaluate arc quality based on deviations from optimal conditions. The AQI provides a qualitative assessment of arc quality, analogous to indices such as arc coverage and arc stability. The study concludes that the AQI serves as an effective operational tool for EAF operators to optimize production and increase the efficiency and sustainability of steel production. The results underline the importance of understanding electric arc dynamics for the development of EAF technology.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

Electric arc furnace oxidizing slag (EAF) has a high density of 3.0~3.7 t/m3 and therefore has a high bulk density when mixed with concrete. Extensive research has been conducted on the use of concrete with high unit volume weight as heavyweight concrete for radiation shielding concrete. In this study, to examine the possibility of developing a radiation shielding concrete, the physical properties of normal concrete, magnetite concrete, EAF concrete, and EAF concrete with added iron powder, were compared. Also, their radiation shielding performance was assessed through shielding tests against X-rays and γ-rays. While the unit volume weight of EAF concrete (3.21 t/m3) appeared lower than that of magnetite concrete (3.5 t/m3), the compressive strength of EAF concrete was greater than those of magnetite and normal concretes. The radiation shielding ratio of magnetite concrete was observed to be 93.9% from the X-ray shielding test, followed by 91.2% of EAF concrete, and 73.7% of normal concrete, indicating a linear relationship with unit volume weight. From the γ-ray shielding test, the performance of EAF and magnetite concretes appeared to be similar. Based on the excellent physical properties and radiation shielding performance of EAF concrete, its potential applicability as radiation shielding concrete was confirmed.

Most of the current methods for stabilizing electric arc furnace (EAF) slag are time-consuming and cannot be completely stabilized. In view of this, this study aimed to apply microbial‑induced calcium carbonate precipitation (MICP) technology in the stabilization of EAF reducing slag, and this was to be achieved by using the reaction between carbonate ions and free calcium oxide (f-CaO) in reducing slag to form a more stable calcium carbonate to achieve the purpose of stabilization. The test results showed that, when the EAF reducing slag aggregates (ERSAs) were immersed in Bacillus pasteurii bacteria solution or water, the f-CaO contained in it would react such that stabilization was achieved. The titration test results showed that the f-CaO content of the ERSAs immersed in the bacterial solution and water decreased. The expansion test results of the ERSAs that were subjected to hydration showed that the seven-day expansion of ERSAs after biomineralization could meet the Taiwan regulation requirement of a less than 0.5% expansion rate. The thermogravimetric analysis showed that both the experimental group and the control group might contain calcium carbonate compounds. The results of the X-ray diffraction analysis showed that the CaCO3 content in the ERSAs that were immersed in the bacterial solution was significantly higher than those that were immersed in water. Moreover, the compressive strength test results of concrete prepared with ERSAs showed that the compressive strength of the control group concrete began to decline after 28 days. In contrast, the experimental group concrete had a good stabilization effect, and there was no decline in compressive strength until the age of 180 days. At the age of 240 days, the surface cracks of the experimental group were particularly small, while the surface of the control group showed obvious cracks. These results confirmed that a mineralization reaction with B. pasteurii bacteria could be used as a stabilization technology for ERSAs.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

In the pursuit of sustainable solutions for carbon dioxide CO2 sequestration and emission reduction in the steel industry, this study presents an innovative integration of steelmaking slag with the modified Solvay process for sodium bicarbonate (NaHCO3) synthesis from saline brines. Utilizing diverse minerals, including electric arc furnace (EAF) slag, olivine, and kimberlite, the study explored their reactivity under varied pH conditions and examined their potential in ammonium regeneration. Advanced techniques such as XRD and ICP-OES were employed to meticulously analyze mineralogical transformations and elemental concentrations. The findings demonstrate that steelmaking slag, owing to its superior reactivity and pH buffering capabilities, outperforms natural minerals. The integration of finer slag particles significantly elevated pH levels, facilitating efficient ammonium regeneration. Geochemical modeling provided valuable insights into mineral stability and reactivity which aligned with the ICP-OES results. This synergistic approach not only aids in CO2 capture through mineral carbonation but also minimizes waste, showcasing its potential as a sustainable and environmentally responsible solution for CO2 mitigation in the steel industry.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

This article represents survey data of historical and architectural documentation of Sri Radha Binod Ashrama locally known as the Panishail temple. Temple architecture is a common feature of traditional religious architecture practice in Bangladesh. This article is a historical and architectural investigation of a less known and mixed type of Hindu temple style in the Bengal region. The Panishail temple complex has a collection of structures that include tomb, temples, and residences aged between fifty to two hundred years. Over the ages, these heritage buildings have displayed a unique architectural style of ancient Bengal and still serving as a living sacred landscape heritage. However, like most of the ancient monuments of Bangladesh, Panishail structures inside this complex stand against the threat of decay and anthropogenic destruction with no effort to conserve them. There is a need for immediate action of research, exploration and preservation to save this historic landmark. This research aims to investigate historic and physical features of the temple complex through a systematic survey and documentation effort. This research will lay a foundation for future conservation intervention on this site. Moreover, this work will significantly contribute to historic temple architecture study in Bangladesh.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

The dispersal potential of crown-of-thorns starfish (CoTS) larvae is important in understanding both the initiation and spread of population outbreaks, and is fundamentally dependent upon how long larvae can persist while still retaining the capacity to settle. This study quantified variation in larval survivorship and settlement rates for CoTS maintained at three different chlorophyll concentrations (0.1, 1.0 or 10.0 µg.L^-1), achieved by varying densities of single-celled flagellate phytoplankton, Proteomonas sulcata. Based on the larval starvation hypothesis we expected that low to moderate algal concentrations would significantly constrain both survival and settlement. CoTS larvae were successfully maintained for up to 50 days post-fertilization, but larval survival differed significantly between treatments. Survival was greatest at intermediate (1.0 µg.L^-1) chlorophyll concentrations, and lowest at highest (10.0 µg.L^-1) chlorophyll concentrations. Rates of settlement were also highest at intermediate (1.0 µg.L^-1) chlorophyll concentrations and peaked at 22 days post-fertilization. Peak settlement was delayed at low chlorophyll concentrations, probably reflective of delayed development, but there was no evidence of accelerated development at high chlorophyll concentrations. CoTS larvae were capable of settling 17-43 days post-fertilization, but under optimum conditions with intermediate chlorophyll concentrations, peak settlement occurred at 22 days post-fertilization. Moderate increases in nutrient concentrations and algal densities may increase the number of CoTS that effectively settle, but are unlikely to influence dispersal dynamics.

Industries, which are mainly responsible for high energy consumptions, need to invest in research projects in order to develop new managing systems for rational energy use and to tackle the devastating effects of climate change caused by human behavior. The study reported in this paper concerns the forging industry, where the production processes generally start with the heating of the steel in furnaces and continue with other processes, such as heat treatments and mechanical machining. One of the most critical operations, in terms of energy loss, is the opening of the furnace doors for the insertion and extraction operations. During this time, the temperature of the furnaces decreases by hundreds of degrees in a few minutes. Because the dispersed heat needs to be supplied again through the combustion of fuel, increasing the consumption of energy and the pollutant emissions, the evaluation of the amount of the lost energy is crucial for the development of operating or mechanical systems able to contain this dispersion. To perform this study, CFD simulation software was used. Results show that at the door opening, because of temperature and pressure differences between the furnace and the ambient, turbulences are generated. Results also show that the amount of energy lost for an opening of 10 minutes for radiation, convection and conduction is equal to 5606 MJ where convection is the main contributor with 5020 MJ. The model created, after being validated, has been applied to perform other simulations in order to improve the energy performance of the furnace. Results show that a reduction of the opening time of the door allows energy savings and limits pollutant emissions.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

During the smelting process of AOD furnace, the unbalanced reaction of material will lead to the occurrence of splashing. It will not only damage the smelting equipment, but also seriously injure the personnel. In this study, first, the information of liquid level, audio information, and vibration information are detected by multiple sensors respectively. Then, the fused information is used to forecast the splashing. Finally, the multitasking fuzzy controller is used to suppress splashing. The results show that the method of forecasting and suppressing splashing can accurately forecast and achieve rapid suppression. Thus, the efficiency of smelting can be improved.

For broadcast spawning invertebrates such as the crown-of-thorns starfish, early life history stages (from spawning to settlement) may be exposed to a wide range of environmental conditions, and could have a major bearing on reproductive success and population replenishment. Arrested development in response to multiple environmental stressors at the earliest stages can be used to define lower and upper limits for normal development. Here, we compared sperm swimming speeds and proportion of motile sperm and rates of fertilization and early development under a range of environmental variables (temperature: 20-36°C, salinity: 20-34 psu, and pH: 7.6-8.2) to identify environmental tipping points and thresholds for reproductive success. We also tested the effects of water-soluble compounds derived from eggs on sperm activity. Our results demonstrate that gametes, fertilization, and early development are robust to a wide range of temperature, salinity, and pH levels that are outside the range found at the geographical limits of adult distribution and can tolerate environmental conditions that exceed expected anomalies as a result of climate change. Water-soluble compounds associated with eggs also enhance sperm activity, particularly in environmental conditions where sperm motility is initially limited. These findings suggest that fertilization and embryonic development of crown-of-thorns starfish are tolerant to a wide range of environmental conditions, though environmental constraints on recruitment success may occur at later ontogenic stages.

The radiative heat transfer in arc plasma models is considered from the point of view of its description in terms of a net emission coefficient, the method of spherical harmonics in its lowest order, and the discrete ordinate method. Net emission coefficients are computed applying approximate and numerical approaches, the multi-band representation of the spectral absorption coefficient with three kinds of its averaging and two datasets. The self-consistent access to the radiative heat transfer is applied to a two-dimensional axisymmetric model of free-burning arc in argon at atmospheric pressure. The results obtained from the models employing the net emission coefficient, the method of spherical harmonics, and the discrete ordinate method are compared.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Computational Fluid Dynamics (CFD)-based simulation has been the traditional way to model complex industrial systems and processes. One very large and complex industrial system that has benefited from CFD-based simulations is the steel blast furnace. The problem with the CFD-based simulation approach is that it tends to be very slow to generate data. The CFD-only approach may not be fast enough for use in real-time decision-making. To address this issue, in this work, the authors propose the use of machine learning techniques to train and test models based on data generated via CFD simulation. Regression models based on neural networks are compared to tree boosting models. In particular, several areas (tuyere, raceway, and shaft) of the blast furnace are modeled using these approaches. The results of the model training and testing are presented and discussed. The obtained R2 metrics are, in general, very high. The results look promising and may help to improve the efficiency of operator and process engineer decision-making when running a blast furnace.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

The Great Barrier Reef (GBR) is currently experiencing widespread crown of thorns starfish (CoTS) outbreaks as part of the fourth wave of outbreaks since 1962. It is believed that outbreaks have become more frequent on the GBR and elsewhere in the Indo-Pacific associated with anthropogenic causes. The two widely accepted potential causes are (1) anthropogenic nutrient enrichment leading to increased biomass of phytoplankton, the food of the planktonic stage of larval CoTS; and (2) overfishing of predators on the juvenile to adult stages of CoTS, for example, commercial fished species such as coral trout. In this study, we show the evidence for the nutrient enrichment causation hypothesis is strong based on a large number of recent studies in the GBR. We also hypothesise that secondary outbreaks in the region between Cairns and Townsville can also be enhanced by nutrient enriched conditions associated with the annual nutrient discharge from Wet Tropics rivers.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

When a railway vehicle moves on a curved rail, sliding contact occurs between the rail head side and wheel flange, which wears the wheel flange down. The thinned flange needs to be restored above the required minimum thickness for structural safety. In this study, a new process and welding wire for restoring worn-out railway wheels by submerged arc welding was developed. To characterize the properties of the restored wheel, dilatometric analysis of phase transformation, SEM/EDX analyses, hardness measurement, and residual stress measurement using the X-ray diffraction method were performed. Finally, wear tests with full-size wheel/rail specimens were carried out. It was confirmed that the weld metal was composed of bainitic microstructures as intended, and welding defects were not observed. The wear amount of the restored wheel was greater than that of the base material, but it was less than half of the wear depth of the weld-repaired wheel with ferritic–pearlitic microstructures. The developed process seems applicable to industry.

With the increased use of laterite nickel ore, the impact of high Al2O3 slag on blast furnace smelting has gradually increased. In this paper, the effects of slag basicity and Al2O3 content on slag viscosity and enthalpy change under constant temperature conditions was investigated. The changes in slag structure were analyzed by activation energy and Fourier Transform Infrared (FT-IR) spectroscopy. The relationship between slag components and slag temperature and viscosity when slag heat is reduced was investigated. The results showed that the viscosity first slightly decreased and then significantly increased with increasing basicity at constant temperature. With the addition of Al2O3 content, the viscosity of the slag increases. The activation energy increases with increasing slag basicity and Al2O3. With increasing basicity, the [SiO4]4- tetrahedral unit trough depth becomes shallow, the [AlO4]5- asymmetric stretching band migrates to lower wave numbers, and the slag structure depolymerizes. With the increase of Al2O3 content, the trough of [SiO4]4- tetrahedra deepens and the center of the symmetric stretching band moves to a higher wave number. The [AlO4]5- asymmetric stretching band becomes obvious, indicating the complexity of the slag structure. When the heat decreases, the slag temperature increases as the basicity increases, and the slag thermal stability is better at the basicity of 0.95-1.05. As the Al2O3 content increases, the thermal stability of the slag becomes worse.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

The steady state tube furnace (SSTF) (ISO/TS 19700) was used to assess the effects altering the reaction zone of a flame had on smoke toxicity measurements. The gas inlet of the apparatus was modified to allow for a mixture of nitrogen and air to be introduced into the system. The volume of air used in each test remained at 2 L min-1 , and additional volumes of nitrogen were varied between tests altering the total volume of gas used in the primary gas inlet. The chosen conditions were representative of under-ventilated flaming by using a restricted oxygen environment. The research shows that the increase in volume flow of gas over a sample increased the smoke toxicity of the materials tested (CO and HCN). When increasing the volume of the primary air-flow through the tube furnace, the flow causes thinning of the flame zone in the apparatus and results in gaseous species spending less time in the reaction zone, resulting in less time available for chemical reactions to occur. This resulted in less complete combustion occurring, and hence an increased yield of measured products of incomplete combustion (CO and HCN), and a decreased yield of products of complete combustion (CO2).

To assess the impact of a deep learning (DL) denoising reconstruction algorithm applied to identical patient scans acquired with two different voxel dimensions, representing distinct spatial resolutions. This IRB approved prospective study was conducted at a tertiary pediatric center in compliance with the Health Insurance Portability and Accountability Act. We used a General Electric Signa Premier unit (GE Medical Systems, Milwaukee, WI) to acquire two DTI sequences of the left knee on each child at 3T: an in-plane 2.0 x 2.0 mm2 with section thickness of 3.0 mm and a 2 mm3 isovolumetric voxel, neither had an inter-section gap. We used a multi-band DTI acquisi-tion with fat-suppressed single-shot spin-echo echo-planar sequence (20 non-collinear directions; b-values of 0 and 600 sec/mm2). The MR vendor-provided a commercially available DL model applied with 75% noise reduction settings to same subject DTI sequences at different spatial res-olutions. We compared DTI tract metrics from both DL-reconstructed scans and non-denoised scans for femur and tibia, at each spatial resolution. Differences were evaluated using Wilcox-on-signed ranked test and Bland-Altman plots. When comparing DL versus non-denoised diffu-sion metrics in femur and tibia using the 2 mm x 2mm x 3 mm voxel dimension there were no significant differences between tract count (p = 0.1, p =0.14) tract volume (p = 0.14, p = 0.29), or tibial tract length (p=0.16); femur tract length exhibited a significant difference (p

Pure titanium is limited to be used in biomedical applications due to its lower mechanical strength compared to its alloy counterpart. To enhance its properties and improve medical implants feasibility, advancements in titanium processing technologies are necessary. One such technique is equal channel angular pressing (ECAP) for its severe plastic deformation (SPD). This study aimed to surface modify commercially pure titanium using micro arc oxidation (MAO) technology and mineral solutions containing Ca and P. The composition and shape of the changed surface were characterized using X-ray diffraction (XRD) and scanning electron microscope (SEM), respectively. The weight % of Ca and P in the coating was determined using Energy Dispersive Spectroscopy (EDS), and the corrosion resistance was evaluated through potentiodynamic measurement. The behavior of human dental pulp cell and periodontal cell behavior was also studied through a biomedical experiment over a period of 1-, 3-, and 7-days using trypsin as the culture medium and ELISA as the observation method. This study showed that the mechanical grain refinement method and surface modification significantly improved the biomechanical properties of commercially pure (CP) Titanium. Although the results showed variations in the absorbance values of cells cultured on different surfaces, this study provides valuable insights into pulp cell behavior and advances the field of biomedical research.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

Process safety plays a vital role in the modern process industry. To prevent undesired accidents caused by malfunctions or other disturbances in complex industrial processes, considerable attention has been paid to data-driven fault detection techniques. To explore the underlying manifold structure, manifold learning methods including Laplacian eigenmaps, locally linear embedding, and Hessian eigenmaps have been utilized in data-driven fault detection. However, only the partial local structure information is extracted from the aforementioned methods. In this paper, these typical manifold learning methods are synthesized to find the underlying manifold structure from different angles. A more comprehensive local structure is discovered under a unified framework by constructing an objection optimization function for dimension reduction of the process data. The proposed method takes advantage of different manifold learning methods. Based on the proposed dimension reduction method, a new data-driven fault detection method is developed. Hotelling’s T2 and Q statistics are established for the purpose of fault detection. Experiments on an industrial benchmark Tennessee Eastman process and a real blast furnace ironmaking process are carried out to demonstrate the superiority and effectiveness of the proposed method.

In recent decades, many attempts have been made to automate the entire welding process, how-ever, there remain many non-automated welding operations that present a constant hazard to workers. This article presents an automated welding solution with collaborative robots, with this contribution, we intend to help companies in this sector increase productivity, improve quality, effectively reduce costs, and improve working conditions.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

A B S T R A C T Genital herpes disease is caused mainly by herpes simplex virus type 2 (HSV-2), which is sexually transmitted with a high prevalence in both developed and developing countries. No vaccine is currently available against genital herpes. In this study, we introduced and expressed two genes encoding HSV-2 glycoprotein D (gD) and VP16 protein and a GFP marker gene (control) in tobacco seedlings. Positive plant infection was assessed through characteristic tobacco mosaic virus disease symptoms on leaves and by monitoring the fluorescence emitted by the expressed GFP protein. Expression of the HSV-gD2 and VP16 antigens was verified by RT-PCR, ELISA and Western blot. As a proof of concept, the immunogenicity and the protection ability of the plant produced gD antigen was tested in a mouse model of genital herpes and compared to gD antigen produced in a mammalian expression system. This showed that the plant-gD preparation, when used in combination with a CpG oligodeoxynucleotide as adjuvant, was highly immunogenic and capable of inducing complete immunity to lethal vaginal HSV-2 challenge in mice. Thus, the data presented here may have implications for the development of a production system for highly immunogenic plant-based HSV-2 vaccine antigens.

This paper addresses the modeling of the iron ore direct reduction process, a process likely to reduce CO₂ emissions from the steel industry. The shaft furnace is divided into three sections (reduction, transition, and cooling), and the model is two-dimensional (cylindrical geometry for the upper sections and conical geometry for the lower one), to correctly describe the lateral gas feed and cooling gas outlet. This model relies on a detailed description of the main physical–chemical and thermal phenomena, using a multi-scale approach. The moving bed is assumed to be comprised of pellets of grains and crystallites. We also take into account eight heterogeneous and two homogeneous chemical reactions. The local mass, energy, and momentum balances are numerically solved, using the finite volume method. This model was successfully validated by simulating the shaft furnaces of two direct reduction plants of different capacities. The calculated results reveal the detailed interior behavior of the shaft furnace operation. Eight different zones can be distinguished, according to their predominant thermal and reaction characteristics. An important finding is the presence of a central zone of lesser temperature and conversion.

Nanostructured transition metal nitrides (TMNs) have been considered a promising substitute for precious metal catalysts toward ORR due to their multi-electron orbitals, metallic properties, and low cost. To design TMNs catalysts with high catalytic activity toward ORR, the intrinsic features of the influencing factor on the catalytic activity toward ORR of nanostructured TMNs need to be investigated. In the paper, titanium nitride (TiN), zirconium nitride (ZrN), and hafnium nitride (HfN) nanoparticles (NPs) are high-efficiency and one-step synthesized by the direct current arc plasma. TiN, ZrN, and HfN NPs with an oxidation layer are applied as the catalysts of hybrid sodium-air batteries (HSABs). The effect of composition and structure attributes of TMNs on ORR catalysis is defined as follows. (ⅰ) Composition effect. With the increase of the oxygen content, the catalytic ORR capability of TMNs decreases progressively due to the reduction of oxygen adsorption capacity; (ⅱ) Structure effect. The redistribution of the density of states (DOS) of ZrN indicates higher ORR activity than TiN and HfN. HSABs with ZrN exhibit an excellent cyclic stability up to 137 cycles (about 140 h), an outstanding rate performance, and a specific capacity of 2817 mAh·g−1 at 1.0 mA·cm−2.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

Cladding is typically used to protect components from wear and corrosion while also improving the aesthetic value and reliability of the substrate. The cladding process induces significant residual stresses due to the temperature difference between the substrate and the clad layer. However, these residual stresses could be effectively utilized by modifying processes and geometrical parameters. This paper introduces a novel methodology for using the weld-cladding process as a cost-effective alternative to various existing reinforcement techniques. The numerical analyses are performed to maximize the reinforcement of a cylindrical tool. The investigation of how the weld cladding develops compressive stresses on the specimen in response to a change in the weld beads and the welding sequence is presented. For the benchmark shape, experimental verification of the numerical model is performed. The impact of the distance between the weld beads and the effect of the tool diameter is numerically investigated. Furthermore, the variation in compressive stresses due to temperature fluctuations during the extrusion process has been evaluated. The results showed that adequate compressive stresses are generated on the welded parts through the cladding process after cooling. Hence, the targeted reinforcement of the substrate can be achieved by optimizing the welding sequence and process parameters.

The prospects of processing blast furnace and steelmaking sludge using Waelz process in a laboratory rotary kiln is shown. The influence of varying thermal treatment modes, furnace atmosphere and type of reducing agents on the level of zinc reduction from sludges was analyzed. In general, the blast furnace sludge contains a high portion of iron (approx.48 wt. %) and can be reused as a charge after satisfactory zinc reduction. It was found that N- atmosphere and high content of the graphite or coke oven reducing agent in combination with high temperature can reduce the content of Zn in the sludge to 0.08 wt. % at 1200 °C for mixture of steelmaking and blast furnace sludge. A significant reduction in the Zn content to 0.66 wt. % occurs at 1100 °C. The content and type of reducing agent play an important role; graphite has shown a better reducing ability compared to coke oven dust. When nitrogen is used, zinc is reduced even without an additional reducing agent, since the carbon contained in the sludge is made use of for the reduction. In an air atmosphere, without the use of a reducing agent, there was no reduction in the Zn content.

The gold deposits of the eastern region of Cuba are genetically related to the lithological formations of the island arc and the ophiolitic complex, which have been studied and exploited since the time of the Spanish colonization in the mid-sixteenth century. These deposits are part of the so-called Aguas Claras-Guajabales mineral field, in the Holguín Province (Cuba) and lie in an extensive elongated strip of approximately 15 km in length. The object of this work is to make an orderly, detailed, and chronological review of the geological and mining work carried out in this region as well as to highlight the degree of study achieved in each of the stages of research. To facilitate this work, an extensive bibliographic review of all available materials was planned and carried out, such as reports, manuals, monographs, and articles. The results obtained from this study highlight that gold mineralization is closely linked to metasomatic processes produced by the circulation of hydrothermal fluids that affected different lithologies of both the volcanic island arc and the ophiolitic complex, it is noteworthy that the highest gold contents are mainly where the lithologies contact each other. This highlights the fact that the presence of alterations such as serpentinization, listvenitization, rodingitization and propylitization have played a primary role in the deposition of gold during mineralization processes. This work could be a very useful guide for future research in this region, as it is an orderly, concrete, and practical compilation of the characteristics of the mineralization and alterations, as well as a precise indication of the spatial position, thicknesses, and contents of the gold horizons.

Tungsten carbide (WC) was well known as a wear-resistant material. Iron-based pow-der was suitable for remanufacturing of cast iron engine parts. To improve the wear resistance of the remanufactured iron-based cast iron engine parts, WC-Co was intro-duced into iron-based powders to prepare composite coatings for cast iron engine components. In this work, FeAlC-x(WC-Co) composite coatings were prepared by plasma transfer arc on compacted graphite cast iron. The influences of WC-Co con-tents in the Fe-AlC-x(WC-Co) composite coatings on the microstructure and properties of the composite coatings were investigated. The composite coatings contained γ-Fe, α-Fe, WC and Fe3W3C mainly. The microhardness of FeAlC-x(WC-Co) composite coatings had the highest hardness of 814 HV0.2, the-lowest coefficient of 0.5 and the lest wear mass loss of 1.3mg when the weight content of WC-Co in the composite coating was 20wt%. As compared with the FeAlC coating, FeAlC-x(WC-Co) composite coating achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

Conobea scoparioides (Plantaginaceae) is an herbaceous plant known as "pataqueira" that grows wild in seasonally wet areas of the Amazon region. It is used for aromatic baths and anti-protozoan remedies by the Brazilian Amazon native people. The main volatile compounds identified in the essential oil of "Pataqueira" were the phenolic monoterpenes thymol and thymol methyl ether and their precursors, the monoterpene hydrocarbons α-phellandrene and p-cymene. A hydrotalcite synthesized from blast-furnace slag exhibited a 3:2 (Mg/Al) molar ratio, and this layered double hydroxide (LDH) was evaluated as a catalyst in converting the main monoterpenes of the "Pataqueira" oil. This action significantly increased thymol content, from 41% to 95%, associated with the percentual reduction of other main components, such as thymol methyl ether, α-phellandrene, and p-cymene. The LDH reaction showed a strong tendency towards producing hydroxylated derivatives, and its behavior was similar to the hypothetical plant biosynthetic pathway, which leads to the production of the monoterpenes of "Pataqueira" oil. Thymol and its derivatives are potent antiseptics applied in pharmaceutical and hygienic products as antibacterial, antifungal, and antioxidant properties, among others. The present work reports a natural source with a high thymol content in aromatic plants from the Amazon, with evident economic value.

This literature review provides an in-depth exploration of the research conducted on the investigation and measurement of residual stress (RS) in Wire Arc Additive Manufacturing (WAAM) products, particularly focusing on how process parameters influence the phenomenon. RS plays a crucial role in determining the mechanical behavior and structural integrity of WAAM components. This review article gives an understanding of the relationship between process parameters and RS to optimize the WAAM processes and ensure the durability of the final products. It also summarizes key findings, measurement techniques, challenges, and future directions in this evolving field. The review also analyzes a measurement of RS in the products of WAAM as a function of process parameters depending on examining various research studies, techniques, and methodologies employed in their studies. Experimental measuring techniques and numerical analysis of RS to determine the impacts of RS in mechanical response in products of WAAM were discussed. By offering a comprehensive overview of current research trends and insights, this review serves as a valuable resource to guide future investigations, fostering the advancement of WAAM as a robust and efficient manufacturing technology.

Whole-brain radiation therapy and stereotactic radiosurgery are two treatment modalities commonly utilized to treat brain metastases (BMs). The aim of this study is to retrospectively analyze the main radio-oncologic and clinical-demographic aspects of a cohort of BM patients treated with Volumetric Modulated Arc Therapy for radiosurgery (VMAT-RS). This is a cross-sectional observational design study with retrospective review of medical records of patients with brain metastases treated with VMAT- RS between 2012 and 2018. Clinical and demographic data, with special attention to sex, age, primary tumor, brain tumor-related epilepsy (BTRE), number and brain location of BMs, Karnofsky Performance Status (KPS), the updated DS-GPA prognostic index and the survival estimated according to the Kaplan-Meier model from the date of radiosurgery were analyzed. One hundred and twenty-one patients with 229 BMs were treated with VMAT-RS. Patients presented 1-4 BMs, which were treated with 5 non-coplanar VMAT arcs. Sixty-eight percent of the patients had lung cancer and 35% of the BMs were in the frontal lobe. Proportion of local control was 88.5%. BTRE prevalence was 30.6%. The median survival time (MST) was 7.7 months. In the multivariate analysis of the Cox Regression model KPS70 (HRKPS<70=2.59; p=0.001) and higher DS-GPA (HRDS-GPAII =0.55, p=0.022; HRDS-GPAIII-IV =0.38, p=0.006) were associated with improved survival. In the univariate analysis, primary tumor, age and the presence of metastases in the posterior fossa (PFBMs) were also significative. In conclusion, the VMAT-RS is a technique with an overall survival comparable to other radiosurgery techniques. The median survival is significantly longer in those with higher KPS and DS-GPA. Other variables such as the type of primary tumor, age and PFBMs could also influence survival, although further studies are needed.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

CO2 emissions resulting from the production of cement is a major issue, but can be limited by the partial substitution of cement by low-carbon-impact additions. The aim of this study was the formulation of a ternary binder based on ordinary Portland cement (OPC), ground granulated blast-furnace slag (GGBS) and flash-calcined sediment (FCS), a dredged waste which was valorized after applying a new heat treatment: flash calcination. The used materials were physically, chemically and mineralogically characterized. The composition of the formulations was optimized using mixture designs. Five formulations, one reference formulation RM (100% OPC), one binary formulation (50% OPC/50% GGBS), and three ternary formulations with a variable FCS rate (10%, 15%, 20%), were selected and characterized fresh and hardened. Results showed that the incorporation of FCS reduced the workability and increased the density. In addition, a decrease in the initial setting time and the heat of hydration peak were observed. In the hardened state, the formulation containing 10% FCS showed 90-day mechanical strengths superior to that of RM. The use of FCS in ternary binders could reduce the environmental impact by reducing greenhouse gas emissions.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

The paper is devoted to the study of a high-pressure short-arc xenon discharge, which is widely used as a light source. Cathodes of such lamps are often doped with thorium for better cathode operation. As a result, thorium can evaporate into a discharge. The study is based on a model of a short-arc xenon discharge plasma, which includes presence of thorium atoms in the plasma. The data obtained show that thorium atoms strongly affect the characteristics of the plasma, reducing its temperature, changing the ionic composition near the cathode, energy balance and generation of optical radiation. Especially interesting is the case when the discharge electrodes have a different shape of the working surface: the anode has a convex or concave shape; the cathode has a different cone angle. The obtained data make it possible to propose a new way to increase the luminous efficiency of xenon lamps due to the appropriate choice of the electrodes working surface shape, which turned out to be an unexpectedly strong factor of affecting plasma characteristics. This, in turn, allows us to develop xenon lamps with the desired characteristics providing optical radiation in the required range of the spectrum and better use of energy.

Having garnered significant attention in the scientific community over the past decade, Wire Arc Directed Energy Deposition (arc-DED) technology is at the heart of this investigation into additive manufacturing parameters. Singularly focused on invar as the selected material, the primary objective revolves around devising an indirect cord height measurement approach. This innovative methodology involves the seamless integration of internal signals and sensors, enabling the derivation of crucial measurements sans the requirement for direct physical interaction or conventional measurement methodologies. Through the course of this research, meticulous alteration of deposition parameters is undertaken to thoroughly scrutinize their influence on the ultimate cord dimensions. The fusion of cutting-edge manufacturing techniques with advanced sensor technology constitutes the essence of this endeavor, offering substantial potential to augment precision and efficiency in additive manufacturing processes. Remarkably cost-effective, this solution circumvents the need for intricate measurements and significantly contributes to the proper layer-by-layer growth process.

Calcium (Ca) is an essential element constituting sedimentary carbonate in subducting sediments. Ca isotopic characteristics of subduction-related rocks could provide insight into the behavior and budget of carbonate and carbon cycles in subduction zones, due to the distinctive δ^44/40Ca ranges of sedimentary carbonate with respect to the mantle. Here, we studied the Ca isotopic compositions of arc magmas from the Northern Luzon arc (NLA), which are evolved from a depleted mantle metasomatized by slab-derived fluids and sediment melts. The δ^44/40Ca values range from 0.76 ± 0.04‰ to 1.01 ± 0.03‰ and cover the typical ranges for bulk silica earth (BSE, ~ 0.94‰) and fresh mid-ocean ridge basalt (MORB, ~ 0.83‰). The Ca isotopes of NLA volcanics are not dominantly determined by the effects of mantle partial melting or fractional crystallization, nor significantly modified by secondary alteration. Instead, the δ^44/40Ca values of NLA volcanics are controlled by the subduction-related metasomatism. The metasomatism by slab-derived fluids (mainly expelled from altered oceanic crust, AOC) dramatically elevated the contents of fluid-mobile elements (e.g., Ba and Pb) with respect to fluid-immobile elements (e.g., Ce). This process, however, rarely modified the Ca isotopes, possibly ascribed to the δ^44/40Ca similarity between AOC and the depleted mantle. The δ^44/40Ca values significantly correlated with subduction indicators (e.g., Sr-Nd isotopes, Ba/Nb, Ce/Pb, and Nb/La), demonstrating the Ca isotopes of NLA volcanics are mainly controlled by the metasomatism of sediment melts subducting from the South China Sea (SCS). Based on the thermal structures and chemical compositions of sediments subducting into global trenches, we propose that carbonate Ca isotopic signals can only be observed in the arcs with high sedimentary Ca fluxes and temperature-pressure conditions well beyond the solidus of H₂O-saturated sediment melting, e.g., NLA, Nicaragua, Guatemala, Colombia, Peru, South Chile, North Vanuatu, New Zealand, and Kermadec. The absence of such signals in other arcs suggests either limited sedimentary fluxes or much of the subducting sedimentary carbonate has been survived during plate subduction to enter the deep mantle.

Arc sensors have been used in seam tracking and widely studied since the 80s; commercial arc sensing products for T and V shaped grooves have been developed. However, it is difficult to use these arc sensors in narrow gap welding because arc stability and sensing accuracy are not satisfactory. Pulse gas melting arc welding (P-GMAW) has been successfully applied in narrow gap welding and all position welding processes, so it is worthwhile to research P-GMAW arc sensing technology. In this paper, we derived a linear mathematical P-GMAW model for arc sensing, and the assumptions for the model are verified through experiments and finite element methods. Finally, the linear characteristics of the mathematical model were investigated. In torch height changing experiments, uphill experiments, and groove angle changing experiments the P-GMAW arc signals all satisfied the linear rules. In addition, the faster the welding speed, the higher the arc signal sensitivities; the smaller the groove angle, the greater the arc sensitivities. The arc signal variation rate needs to be modified according to the welding power, groove angles, and swing or rotate speed.

The article takes the case of the adoption of machine learning in a steel manufacturing process through a platform provided by a novel Canadian startup, Canvass Analytics. This way the steel company could optimize the process in a blast furnace. The content of the paper includes a conceptual framework on key factors around steel manufacturing and machine learning. Method: The article takes the case of the adoption of machine learning in a steel manufacturing process through a platform provided by a novel Canadian startup, Canvass Analytics. This way the steel company could optimize the process in a blast furnace. The content of the paper includes a conceptual framework on key factors around steel manufacturing and machine learning. Results: This case is relevant for the authors by the way the business model proposed by the startup attempts to democratize Artificial Intelligence and Machine Learning in industrial environments. This way the startup delivers value to facilitate traditional industries to obtain better operational results, and contribute to a better use of resources. Conclusion: This work is focused on opportunities that arise around Artificial Intelligence as a driver for new business and operating models. Besides the paper looks into the framework of the adoption of Artificial Intelligence and Machine Learning in a traditional industrial environment towards a smart manufacturing approach.

In the study, ground granulated blast furnace slag was activated with a wide variety of sodium salts to compare the effect of their pH and anion size on the hydration progress and compressive strength development of GGBFS pastes. Research was carried out on samples activated with twelve different sodium salts, cured for one year. Changes in their phase composition (XRD), loss on ignition at different temperatures, expansion and microstructure (SEM+EDS) were examined over the entire curing period. Studies have shown that the presence of sodium ions is more important than the pH of the system, as activation took place even in the case of compounds whose solutions are characterized by low pH, such as sodium tartrate or phosphate. The compressive strength of the pastes ranged from approximately 8 to 65 MPa after one year of curing.

This study addresses the challenge of treating skin cancer effectively, especially in visible areas like the face, where traditional methods may be undesirable. Current options, including surgery and radiation therapy, have limitations such as complexity, expense, and imprecise dose delivery. The proposed solution involves additively manufacturing personalized patches using diagnostic imaging data, offering a targeted and controlled dose of beta-emitting isotopes like Y-90. The patches, tailored to the tumor's shape and depth, aim to minimize damage to healthy tissues and structures. Through 3D printing technology we demonstrated the feasibility of creating individualized applicators filled with radioisotopes, that have the potential to deliver therapeutic doses while ensuring patient comfort and affordability. This innovative approach, based on radiation delivery simulations, offers a promising future alternative to conventional radiation therapy methods. Clinical trials are required to validate its efficacy and safety, but the potential for reduced radiation exposure and enhanced treatment precision positions this personalized and targeted therapy as a valuable advancement in skin cancer treatment.

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

RNA extraction from human cumulus cells (CCs) is considered challenging due to low cell’s pop-ulation and small cell. The successful gene expression analysis from cumulus cells ultimately de-pends on an excellent concentration of Ribonucleic acid (RNA) yield by an appropriate technique. Our study aims to consolidate appropriate cumulus cell collection method, preparation and ex-traction techniques to ensure a good yield of RNA for better gene expression analysis. From the results obtained, the optimal strategy found involved mechanical denudation without an enzy-matic process, followed by the use of RNA stabilizer prior to RNA extraction. Subsequently, uti-lizing a smaller homogenizer, preferably manual pressure control with filter (Bio-Masher III®) is paramount for a pure and homogenize sample. Subsequently, during RNA extraction, the use of RNeasy micro kit and RNA carriers is recommended. These sample collection, preparation, and extraction techniques yielded an excellent-quality RNA concentration and successful gene expres-sion analysis. We also conducted a systematic review to consolidate our findings with current evidence of RNA extraction technique. Our results added a value as a current strategy for opti-mizing RNA extraction in CCs for experimental studies. Thus, our findings can contribute to for-mulating a better strategy for optimizing the RNA extraction in CCs for transcriptomic studies.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

The high figure of merit and earth abundance of Cu₁₂Sb₄S₁₃ thermoelectric ma- terials have recently attracted many attentions toward these type of complex compounds. Intrinsic low thermal conductivity, as well as tunable electronic transport properties, make them suitable for thermoelectric power generation. In this study, we perform a comparative theoretical study on the substituted compounds, primarily at the Cu site including known tetrahedrite Cu₁₂Sb₄S₁₃, by means of first-principles calculations. The density functional theory of electric structure is applied to investigate the result of substitution.

Electromobility has gained significant attention in the auto- motive industry, with car manufacturers striving to improve the charging experience for their users. In this study, we compare multiple realistic charging strategies in order to quantify the benefits arising from better planning of charging sessions. We base our evaluation on electricity price data from three regions: Sweden (SE3 region), Germany (DE region), and Denmark (DK2 region). This data is obtained from the ENTSO-E Transparency Platform, covering the two full years 2021 and 2022. We enhance this dataset with commercial price forecasts from the company StormGeo and benchmark it against a naive forecasting method. The primary aim of our work is to compare how the strategies of varying levels of complexity perform across the three different countries in terms of minimizing energy costs for electric car users.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

Micro-arc oxidation (MAO) is an emerging technology employed to produce high hardness or anti-corrosion ceramic coatings on lightweight metals such Al, Ti, Mg and their respective alloys. However, under non-lubrication conditions, such coatings exhibit relatively high friction coeffi-cients. To enhance the friction reduction properties of the MAO coatings, we employed a one-step MAO process with varying concentrations of graphene oxide (GO) in an aluminate sys-tem electrolyte to create composite coatings on the surfaces of Ti-6Al-4V alloy. The effect of concentrations of GO particles on microstructure, composition, and wear behavior of the result-ing composite coatings was investigated. Measurements of the coating's thickness, hardness, and roughness have also been conducted. Ball-on-disk friction test under dry condition were carried out to reveal tribological behavior of the MAO coating. The addition of graphene oxide in the electrolyte reduces the friction coefficient, with the composite coating containing 5 g/L of GO particles displaying the most effective friction reduction. Moreover, coating thickness increases with higher GO concentration. This friction reduction can be attributed to the particles in the coating acting as lubricants during friction, while GO also reduces adhesive damage, shifting the wear mechanism from adhesive to abrasive.

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

Transportation electrification has been identified as a crucial shift to be made for achieving energy security and emission reduction targets. Electric Vehicles (EVs) play a significant role in achieving these targets; therefore, there is a growing trend to develop new EV technologies and associated infrastructure. Along with these developments, EVs' Quality of Service (QoS) aspects should be enhanced to increase the number of EVs on the road. Various QoS factors are defined to assess the QoS of EVs, and one of the two aims of this paper is to provide a comprehensive review of these factors. The other aim is to review recent developments of associated communication technologies which are essential for exchanging information between EVs and charging stations. This paper serves as a comprehensive review and useful reference for researchers working on QoS aspects of EVs and associated communication systems aiming to enhance the QoS.

Appling the controlling relative permittivity and permeability in the equations for the gravitational-magnetic-electric field interaction, a very large variation of the gravitational acceleration of the Earth by electric/magnetic field could be arrived at. This conclusion may be supported by some of the experiments for the gravitational effect of superconductivity.

In light of the current situation where no testing equipment is available for measuring thermal deformation of objects, this paper proposes a novel method for accurate and precise measurement. The method overcomes the limitations of previous approaches that relied on pitch angle. By utilizing the principle of biplane multiple reflections, a bivariate laser spot displacement analysis algorithm is devised to attain highly precise measurements of bivariate angles. Additionally, a temperature gradient comparison algorithm is introduced to calculate the indicator test results under specific temperature conditions. To validate the effectiveness and reliability of this method, a testing system is constructed and utilized. The results demonstrate that the thermal deformation angle change test achieves an impressive accuracy of 0.015″ and a rate of thermal deformation angle change of 0.3247″/°C. These values are in close agreement with the previously simulated analysis result of 0.359″/°C, with only a relative error of 9.55%. Therefore, the test results confirm the efficacy and reliability of this testing method along with the feasibility of the algorithm processing.

This paper presents a novel approach of welding thick steel plates that offers time and energy savings compared with conventional techniques. The combination of gas metal arc welding (GMAW) and hot-wire technology simplifies the joint configuration and enhances the process tolerance. In this study, a square butt joint was prepared with as-cut edges and a thickness of 15 mm. The relationship between the welding current and the deposition rate of solo GMAW showed limitations and low process tolerance. Increasing the welding current led to a larger deposited volume with unnecessary weld penetration. An independent deposition volume due to hot-wire insertion was used to improve process tolerance. This approach provided an additional volume without increasing the welding current and reduced unnecessary penetration. With optimized parameters, full-penetration single-pass welding was achieved. Compared with the formation of a typical single-v butt joint at a similar welding speed of 30 cm/min, the proposed process reduced the minimum arc time and power consumption by approximately 83% and 62%, respectively. Moreover, a single pass at a travel speed of 60 cm/min was achieved with approximately 91% and 81% less arc time and power consumption, respectively. In summary, the combined process simplifies the joint configuration, enables full-penetration single-pass welding, and reduces time and energy requirements.

Life Cycle Assessment (LCA) is a technique developed to measure possible environmental impacts during the manufacture and use of a given product or service. Additive Manufacturing (AM) has proven to be suitable in several industries, especially wire and arc additive manufacturing (WAAM), offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and equivalent CO₂ emissions (CO₂e). This study aimed to develop a methodology to evaluate environmental indicators during the life cycle assessment, from gate-to-gate, in the production of two low-alloy carbon steel metal parts (flanges) using ER-90 wire and allowed identifying the main stages that most influence environmental indicators. The total energy consumption in the production of flanges 1 and 2 were, respectively, 10,239.0 MJ, 12,754.0 MJ and the total carbon footprint, respectively, 714.1 kgCO₂e kg^-1 and 749.3 kgCO₂e kg^-1.

Early in the middle of the 1800s. Up until about 1900, the automotive land speed record 1 was held by an electrical vehicle. Unfortunately, internal combustion engine vehicles did not do 2 well in the market due to their high cost, limited speed, and short range in the 20th century, which 3 resulted in a global fall in their use as private motor vehicles. Since there are no fuel emissions into 4 the environment, there are important uses for electrical vehicles, Electric cars, or EVs, have a closed 5 circuit, cheap operating costs, no maintenance requirements, and excellent performance. The goal 6 of this project is to assess the current state of electric vehicles and the issues surrounding the global 7 advancement of electric vehicle technology. Because of the changing climate.8

The rapid growth rate of the elderly population is a serious current issue in most countries, affecting them economically through needed medical treatment and healthcare planning. The priority concern is how to reduce the number of elderly people requiring long-term healthcare and raise the number who are able to live independently. This study executed a behavior assessment of elderly person’s self-reported use of electric scooters and analyzed their degree of acceptance of these assisted living tools, partly through a related factor analysis of our survey instrument. We used this questionnaire survey as our research method, applying SPSS22 software for factor analysis that revealed five survey facets.

This paper (the first of a series of two) seeks to describe the experimental results of removing arsenic from dust collected in electrostatic precipitators of copper into the pyro-metallurgy gas cleaning systems. The first work corresponds to the treatment of dust contained in gas off generated in the copper Flash Smelting Furnace process (FS dust), while the second focuses on the treatment of dust generated from a Fluidized Bed Roasting Furnace (RP dust). The dust is complex sulphur-oxide-metals with concentrations of copper above 10 wt % and relatively high concentrations of silver. Due to the dust has an arsenic’s concentration above 5 wt %, makes it difficult to recover valuable metals through hydro-metallurgical processes or by direct recirculation of the dust into a smelting furnace. Thus, the development of pyrometallurgical processes aimed to reduce the concentration of arsenic in dust is the main purpose of this study, particularly the production of a material suitable for recirculation in smelting operations. The works conducted provide a detailed characterization of the dust, including Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN), Scanning electron microscope-Energy Dispersive X-ray analysis (SEM/EDS), X-ray diffraction (XR-D), elemental chemical analysis using Atomic Adsorption (A. A.) and X-Ray Fluorescence (X-RF). By considering that arsenic volatilization requires a process of reduction-sulphidation-volatilization, the works explore the roasting of mixtures of copper concentrate/dust, sulphur/dust and pyrrhotite/dust. The degree of volatilization was determined by elemental chemical analysis of arsenic in the mixture after and before the roasting process. The results indicated the effect of parameters such as temperature, gas flow, gas composition and the ratio of mixtures (concentrate, sulphur or pyrrhotite)/dust on the volatilization of arsenic. The findings indicate that the concentration of arsenic in the FS dust can be reduced to a relatively low level (<0.5 wt %), allowing to the material to be recirculated into smelting processes.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Today, there are commercially available high-performance electric wheelchairs, capa-ble of responding to strong limitations. However, despite these advancements, there is a significant portion of the population with severe disabilities who cannot access this mobility solution due to safety reasons. Indeed, either due to motor issues preventing reliable control of the wheelchair's commands, or associated visual or cognitive pathologies, the use of an electric wheelchair by these individuals would put them at risk and could also constitute a danger to those around them. This is why our research team is working on the development of augmented wheelchairs that allow a greater autonomy. We are mainly developing a system compatible with all electric wheel-chairs on the market, capable of making them anti-collision and anti-fall on uneven ground (sidewalks, stairs, etc.). In this article, we present our solution regarding the anti-collision function, in particular the sensors used to do this, as well as the strategy. We will focus on the shortcomings and weaknesses of various types of sensors and demonstrate how, by combining them in a certain way, we can develop a collision avoidance device capable of managing the diversity of everyday life situations. The two types of sensors that will be combined here are an in-house developed special near infrared sensor from the laboratory and a commercially available ultrasonic sensor. We will present the internal operation of the sensors, their limitations, experimental tests involving integration with the wheelchair, and the structure of the complete device.

The thermal degradation of brakes has a significant impact on the stability of pure electric commercial vehicles during long downhill braking. Based on road slope and using fuzzy control method, design strategies for motor regenerative braking force and friction braking force distribution, with the aim of reducing friction braking force, improving braking stability, and recovering braking energy. By establishing driving conditions on roads with different slopes and using numerical analysis methods to verify the proposed control strategy. the results show that under the 6% constant slope driving condition, the vehicle maintains a constant speed of 30km/h downhill driving, and the braking energy recovery rate reaches 50.93%; Under the condition of 3% -6% gradient driving, the vehicle speed fluctuates slightly, but it can still be maintained at a constant speed of 30km/h for downhill driving through the adjustment of the motor's reverse drag characteristic, with a braking energy recovery rate of 49.97%; During the process of driving downhill at a constant speed, the frictional braking force does not participate in braking; The braking energy recovery rate is determined by the slope and braking deceleration.

In this non-exhaustive review, we discuss the importance of invariant vectors in atomic physics, such as the Laplace-Runge-Lenz vector, the Redmond vector in the presence of an electric field, the Landau-Avron-Sivardière vector when the system is subject to a magnetic field, and the supergeneralized Runge-Lenz vector for the two-center problem. Application to Stark and Zeeman effects are outlined. The existence of constants of motion in the charge-dyon system is also briefly mentioned.

Bacteria play a key role in both human health and disease. One of the most prevalent harmful bacteria is E. coli which is responsible for several illnesses ranging from diarrhea, stomach cramp and fever. In this work we explore the application of moderate electric or magnetic fields for treating deionized water that is contaminated with E. coli. We found that moderate alternating electric (AC) fields (10 V/cm to 1kV/cm) and moderate static magnetic fields (10 to 65 mT) can significantly inactivate E. coli by up to 90% or more. This provides the possibilities of developing a low cost and a practical bacteria inactivation technique using electric or magnetic fields.

Aspalathin (ASP) can protect H9c2 cardiomyocytes against high glucose (HG)-induced shifts in myocardial substrate preference, oxidative stress and apoptosis. While the protective mechanism of aspalathin remains unknown, nuclear factor (erythroid-derived 2)-like 2 (Nrf2) has emerged as a key factor for intracellular responses against oxidative stress. Therefore, we hypothesized that aspalathin protects the myocardium against hyperglycemia-induced oxidative damage by up-regulating Nrf2 expression in H9c2 cardiomyocytes and diabetic (db/db) mice. Using an oxidative stress RT2 Profiler PCR array, ASP at a dose of 1 µM was demonstrated to protect H9c2 cardiomyocytes against HG-induced oxidative stress, but silencing of Nrf2 abolished this protective response of ASP and exacerbated cardiomyocyte apoptosis. Db/db mice and their non-diabetic (db/+) littermate controls were subsequently treated daily for 6 weeks with either a low (13 mg/kg) or high (130 mg/kg) ASP dose. Compared to nondiabetic mice the db/db mice presented increased cardiac remodeling and enlarged left ventricular wall that occurred concomitant to enhanced oxidative stress. Daily treatment of mice with ASP at a dose of 130 mg/kg for 6 weeks was more effective at reversing complications than both a low dose ASP or metformin, eliciting enhanced expression of Nrf2 and its downstream antioxidant genes. These results indicate that ASP maintains cellular homeostasis and protects the myocardium against hyperglycemia-induced stress through activation of Nrf2 and its downstream target genes.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.