The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The safety of lithium-ion batteries is critical to the safety of battery electric vehicles (BEVs). The purpose of this work is to develop a method to predict battery thermal runaway in full electric vehicle crash simulation. The thermal-electrical-mechanical coupled finite element analysis is used to model an individual lithium-ion battery cell, a battery module, a battery pack, and a battery electric vehicle with 24 battery modules in a live circuit connection. The lithium-ion battery is modeled using a representative approach, with each battery internal component individually modeled to represent its geometric shape and realistic thermal, mechanical, and electrical properties. A resistance heating solver and Randles circuit model built with generalized voltage source are used to simulate the battery electrical behavior. The thermal simulation of the battery accounts for the heat capacity and thermal conductivity of various cell component materials, as well as heat conduction, radiation, and convection at their interfaces. The mechanical property of battery cell and battery module models is validated using spherical punch tests. The electrical property of the battery cell and battery module models is verified against CircuitLab simulation in an external short circuit test. The simulation result of battery module’s internal resistance agrees with the experimental data and the literature value. The multi-physics coupling phenomenon is demonstrated with a cylindrical compression simulation on the battery module. The multi-physics BEV model with 24 live battery modules is used to simulate the external short-circuit test and the side pole impact test. The simulations run time is less than 24 hours. The results demonstrated the feasibility of using representative battery model and multi-physics analysis to predict battery thermal runaway in full electric vehicle crash analysis.

The study examines the noise, vibration, and harshness (NVH) management of electric vehicle (EV) powertrains, considering the challenges of the automotive industry's transition to electric drivetrains. The growing popularity of EVs brings new NVH challenges, as the lack of internal combustion engine (ICE) noise makes drivetrain noise more prominent. Key to managing NVH in EV powertrains is understanding the noise from electric motors, inverters, and gear systems. Noise from electric motors, mainly resulting from electromagnetic forces, and high-frequency noise generated by inverters significantly impact overall NVH performance. The article details sources of mechanical noise and vibration, including gear defects in gear systems and shaft imbalances. Methods presented in the publication include simulation and modeling techniques that help identify and solve NVH difficulties. Tools like multi-body dynamics (MBD), finite element method (FEM), and multi-domain simulation are crucial for understanding the dynamic behavior of complex systems. With the support of simulations, engineers can predict noise and vibration challenges and develop effective solutions during the design phase. The study emphasizes the importance of a system-level approach in NVH management, where the entire drivetrain is modeled and analyzed together, not just individual components.

China’s leading development of a complete battery value chain for Electric Vehicles (EV) is restructuring the global automotive sector. The competitive advantage of China's EV battery industry lies on its firms’ core competency and political economic geography. Based on first-hand empirical material and data obtained from years of fieldwork in an EV battery cluster in South China, this paper identifies what the Chinese EV battery industry’s core competency is and details how it is built up from below. The current core competency of Chinese battery firms is their mass manufacturing capability to supply lithium-ion batteries vehicle manufacturers (OEMs) with stable and consistent quality as well as competitive prices. This competency is acquired by firms through technological learning at workshop level while taking use of their experiences accumulated in mass production of batteries for consumer electronics sectors. Furthermore, the rapid learning and accumulation of knowledge on battery manufacturing at large scale is also facilitated by the industrial cluster environment where firms are embedded. Supported and promoted by local government policies, Chinese EV battery clusters are composed of firms from different segments of a complete battery value chain. The findings illuminate the likely strategic strengths, weaknesses, and futures of the Chinese EV battery industry in global competition.

The purpose of this research is to present a thorough evaluation of the energy management system, which consists of hybrid energy storage systems, and its control algorithms, which may be used in electric vehicles. This paper outlines the characteristics of electric vehicles, research methods, analysis of the hybrid energy storage system architecture, converter topology, and energy management techniques. The strength and co-occurrence of keywords over the past ten years are shown in this study using a systematic research framework for performing a literature review and using keyword analysis techniques. The study reveals a pattern of recently and frequently used terms in works of literature. Consequently, their suitability, benefits, and drawbacks are assessed. In this study, the hybrid energy storage system and converter circuit architecture are evaluated and rated. Non-isolate DC-DC converter converter connected to SC is a suitable configuration for the hybrid converter because it is simple to build, reliable, and has minimal loss/weight/cost, which improves vehicle performance. In terms of the application of control strategies, it is shown that deterministic and fuzzy rule-based control techniques are successfully assessed using real-scale vehicle experiments and selected for manufacturing. On the other hand, real-time optimization-based energy management techniques have been effectively shown in lab-scale tests and may be used in a future real-scale vehicle.

Electric vehicles can effectively make use of the time-of-use electricity price to reduce the charging cost, meanwhile using the grid power to preheat the battery before departure is particularly important for improving the vehicle mileage and reducing the use cost.In this paper, a dynamic programming algorithm is used to optimize the battery AC charging-preheating strategy to minimize the total cost of battery charging and preheating, with the charging current and battery preheating power consumption as the control variables. The cost difference between the optimized control strategy and the conventional preheating strategy was analyzed under different ambient temperatures (-20℃~ 0℃) and different target travel time (7:00 ~ 12:00). The simulation results show that the optimized control strategy makes the battery SOC and temperature reach the set value at the user's target departure time, and the total cost of the grid is the lowest. Compared with the conventional preheating strategy, the optimized control strategy can utilize the power grid energy in the valley price area, reduce the opening time of water heating PTC in the flat and the peak price zones, and the cost utilization rate can reach 18.41% ~ 73.96%, and the cost-saving effect is significant.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

Efficient processing of end-of-life lithium-ion batteries of electric vehicles is important and a pressing challenge for a circular economy. Regardless of whether the processing strategy is recycling, repurposing or remanufacturing, the first processing step would usually involve disassembly. As battery disassembly is a dangerous task, efforts have been made to robotise it. In this paper, a robotic disassembly platform using four industrial robots is proposed to automate the non-destructive disassembly of a plug-in hybrid electric vehicle battery pack into modules. The work was conducted as a case study to demonstrate the concept of autonomous disassembly of an electric vehicle battery pack. A two-step object localisation method based on visual information is used to overcome positional uncertainties from different sources and is validated by experiments. Also, the unscrewing system is highlighted, and its functions, such as handling untightened fasteners, loosening jammed screws, and changing the nutrunner adapters with square drives, are detailed. Furthermore, the time required for each operation is compared with that taken by human operators. Finally, the limitations of the platform are reported and future research directions are suggested.

This work presents the design, construction and performance evaluation of a photovoltaic greenhouse as an energy hub (EH) in modern agriculture that integrates battery energy storage (BES) and an electric vehicle charging station (EV). The greenhouse is composed of 48 semi-transparent PV panels with nominal transparency of 20% and 110 W capacity. The control of the PV greenhouse as EH was approached as an optimization problem with the aim of minimizing the cost of the energy used from the grid. Simulation results indicate that the integrated BES is capable of balancing power transactions within the microgrid. In addition, it was found that the case of slow charging of the EV at night was less demanding on the BES than fast charging during the day in terms of abrupt power transitions and average depletion of BES SOC (61% vs 53%). Empirical results also demonstrated the negative impact of dust generated by agricultural activity on the performance of solar panels. For a period analyzed of three years, an average yearly production loss of 6.8% was calculated.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

This study establishes life cycle assessment model to quantitively evaluate and predict material resource consumption, fossil energy consumption and environmental emissions of plug-in hybrid electric vehicles (PHEVs) by employing the GaBi software. the envi-ronmental impact of different vehicle working conditions, power battery degradation scenarios and mileage scenarios on the operation and use stage of PHEV, BEV and HEV is distinguished. The findings indicate that under urban, highway, and aggressive driving conditions, PHEVs' life cycle material resource and fossil fuel consumption exceed that of BEVs but are less than HEVs. Battery degradation leads to increased material resource consumption, energy use, and environmental emissions for both PHEVs and BEVs, en-vironmental emission of BEVs are more sensitive than those of PHEVs to the impact of power battery degradation. Among different-mileage scenarios, PHEVs demonstrate the least sensitivity to increased mileage regarding life cycle material resource consumption, with the smallest increase. Future projections for 2025 and 2035 suggest life cycle GWP of HEV, PHEV and BEV in 2035 is 1.21×104, 1.12×104 and 1.01×104 kg CO2-eq respectively, which is decreased by 48.7%, 30.9% and 36.1% compared with those in 2025. The out-comes of this study are intended to bolster data support for the manufacturing and de-velopment of PHEV, BEV and HEV under different scenarios and offer insights into the growth and technological progression of the automotive sector.

Evapotranspiration is a critical component of the hydrological cycle, and it has a decisive impact on the ecosystem balance in arid and semi-arid regions. The Yinchuan Plain, located in the Gobi of Northwest China, has a strong surface ET. In order to assess the ET pattern in this region, we obtained the ETa of Yinchuan Plain between 1987 and 2020 using the GEE platform. We employed the Surface Energy Balance Model (SEBAL), specifically geeSEBAL, to analyze the change pattern of ET over different seasons, years, and land types. The results show that: ① In spring, the daily ETa of the Yinchuan Plain is highest in the central lake wetland area, with a maximum value of 4.32 mm day-1. In summer, it is concentrated around the croplands and water bodies, with a maximum value of 6.90 mm day-1; In Autumn and winter, it is mainly concentrated around the water bodies and impervious areas, with maximum values of 3.93 and 1.56 mm day-1, respectively. ② From 1987 to 2020, the ET of the Yinchuan Plain showed an obvious upward and downward trend in some areas with significant land use changes, but the overall ET of the region remained relatively stable without dramatic fluctuations. ③ The evapotranspiration of different underlying land use types in the Yinchuan Plain region is as follows: water body>cultivated land>impervious>grassland>bare land. Our results showed that geeSEBAL is highly applicable in the Yinchuan Plain area. It allows for the accurate and detailed inversion of ET in the study area, which facilitates the study of regional hydrological cycle and water governance.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

In a V2V communication environment, the control of electric vehicle platoons faces issues such as random communication delays, packet loss, and external disturbances. To address these issues, a robust UKF-MPC-based longitudinal control algorithm for the platoon is designed. First, a longitudinal kinematic model of the vehicle platoon is constructed, and discrete state-space equations are established. The robust UKF algorithm is derived by enhancing the UKF algorithm with Huber-M estimation. This enhanced algorithm is then used to estimate the state information of the leading vehicle. Based on the vehicle state information obtained from the robust UKF estimation, feedback correction compensation is added to the MPC algorithm to design the robust UKF-MPC longitudinal controller. Finally, The effectiveness of the proposed controller is verified through CarSim/Simulink joint simulation. Simulation results show that the robust UKF-MPC longitudinal controller performs better compared to the MPC and UKF-MPC longitudinal controllers. When facing the communication delay and packet loss problems, the robust UKF-MPC longitudinal controller has higher control accuracy and less performance degradation. It has strong robustness and stability.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

As a critical component of electric vehicles, the powertrain has a significant impact on the overall performance of the vehicle. In addressing the challenge of lengthy testing cycles, this study develops a para model of the powertrain utilizing digital twin (DT) technology, thereby establishing a framework for simulation testing of multi-controller intermodulation. The research conducts functional definition coverage testing through the design of specific functional requirement use cases, and it validates the failure mechanism via fault injection use cases. The results indicate that the DT testing platform can effectively simulate the operational interactions among various controllers within the powertrain system. In comparison to traditional field testing, the digital twin-based testing methodology offers enhanced operational efficiency and allows for the examination of testing conditions that are impractical to implement in real vehicles, particularly in the context of fault injection testing, thus facilitating the early detection of potential safety risks within the system. The advancement of this technical solution holds significant practical implications for the future mass production and development of electric vehicles.

Vehicle logo detection plays a crucial role in various computer vision applications, such as vehicle classification and detection. In this research, we propose an improved vehicle logo detection method leveraging the MAMBA structure. The MAMBA structure integrates multiple attention mechanisms and bidirectional feature aggregation to enhance the discriminative power of the detection model. Specifically, we introduce the Multi-Head Attention for Multi-Scale Feature Fusion (MHAMFF) module to capture multi-scale contextual information effectively. Moreover, we incorporate the Bidirectional Aggregation Mechanism (BAM) to facilitate information exchange between different layers of the detection network. Experimental results on a benchmark dataset (VLD-45 dataset) demonstrate that our proposed method outperforms baseline models in terms of both detection accuracy and efficiency. Furthermore, extensive ablation studies validate the effectiveness of each component in the MAMBA structure. Overall, the proposed MAMBA-based vehicle logo detection approach shows promising potential for real-world applications in intelligent transportation systems.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Transportation contributes significantly to greenhouse gas emissions, with electrification offering a promising solution. This study evaluates the degradation of State of Health (SOH) over 2.5 years for electrified buses under different charging protocols: DC Fast charging and Flash charging. The vehicles’ models, charging protocols, and financial implications are discussed. High-level simulations reveal that after 2.5 years, the Flash charging vehicle’s SOH reaches 88.93%, while the DC fast charging vehicle reaches 89.46%, showing a 0.47% difference. This slight variance is attributed to Flash charging vehicles avoiding full charge/discharge cycles, reducing battery aging impact. Considering this minimal SOH degradation difference, the choice between DC Fast charging and Flash charging primarily hinges on capital expenditure disparities. Flash charging, with its lower initial battery capacity and reduced capital costs, presents a compelling alternative for city busoperators seeking to electrify their fleets.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

Sentiment analysis is a technique used to understand the publics’ opinion towards an event, product, or organization. For example, positive or negative opinion or attitude towards electric vehicle (EV) brands. This provides companies with valuable insight about the public's opinion of their products and brands. In the field of natural language processing (NLP), transformer models have shown great performances over the traditional machine learning algorithms. However, these models have not been explored extensively in the EV domain. EV companies are becoming signif-icant competitors in the automotive industry and are projected to cover up to 30% of the United States light vehicle market by 2030 [1]. In this study, we present a comparative study of large language models (LLMs) including bidirectional encoder representations from transformers (BERT), robustly optimized BERT approach and generalized autoregressive pretraining for language un-derstanding using Lucid motors and Tesla motors YouTube datasets. Results evidenced LLMs like BERT and her variants are off-the-shelf algorithms for sentiment analysis, specifically, when fi-ne-tuned. Furthermore, our findings presents the need for domain adaptation whilst utilizing LLMs. Finally, the experimental results showed that RoBERTa achieved consistent performance across the EV datasets with a F1 score of at least 92%.

In current electric vehicles, the traction battery is intended to store energy. When designing this battery different parameters must be taken into account in order to arrange the battery/module/cells in the mechanically and thermally safest configuration. Moreover, the battery layout must have a correct dynamic behavior in possible collisions. In the present study, different battery configurations plus added energy absorbers are analyzed. In order to do that, an internal combustion vehicle modeled with finite elements is applied as the reference model. The structural behavior of the different battery configurations in the event of a side collision is examined. Firstly, the safest arrangement is stablished, both with respect to cabin intrusion and thermal runaway propagation. Secondly, the safest arrangement that guarantees the safety of the occupants in the event of a side collision is analyzed but using the MADYMO. This software includes experimentally validated dummies which allow have an insight in the stresses experienced by occupants. On the one hand, the analysis states that the battery pack inclusion in the vehicle increases the stiffness of the car floor, resulting in fewer intrusions in the passenger compartment. Therefore, a greater safety for the occupants is reached. On the other hand, none of the configurations analyzed has shown enough safety against the phenomenon of Thermal Runaway.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

Modern automotive systems should must satisfy strict reliability requirements. Most of the real vehicle systems and safety-critical networks have complex interconnections. Sensitivities and probabilistic uncertainties of reliability of System with Complex Interconnections (SwCI) can be investigated by the Monte-Carlo Simulation (MCS). The paper focuses on sensitivities and parametrical uncertainties of SwCIs reliability. The proposed method can be used forimplemented in the investigation of uncertainties of SwCIs reliability – in other wordsi.e., for in the determination of critical system elements and to estimateion of the Required Number of Spare Parts (RNSP) of the system, which depends on the probability of allowable spare equipment shortage.

Electric vehicles (EVs) play a significant role in reducing carbon emissions. In the US, EVs are mostly owned by multi-vehicle households, and their usage is primarily studied in the context of vehicle miles traveled. This study takes a unique approach by analyzing EV usage through the lens of vehicle choice (between EVs and internal combustion engine vehicles) within multi-vehicle households. A two-step machine-learning framework (clustering and decision trees) is proposed. The framework determines the preferred trip category for EV use and captures the effects of household attributes, driver attributes, built-environment factors, and gas prices on EV use in multi-vehicle households. Results indicate that discretionary trips (accumulated local effect = 0.037) are mostly preferred for EV use. EV preference is more pronounced among households with fewer workers (<2) and lower income levels. These findings are valuable for policymakers and auto manufacturers in targeting specific market segments and promoting EV adoption.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

In the context of constructing new power systems, distribution networks are increasingly incorporating distributed resources such as distributed photovoltaic (PV) systems, decentralized wind turbines (WT), and new types of energy storage system (ESS), which may lead to prominent issues such as voltage overruns and reverse heavy overloads in the distribution network. While distributed resources are valuable for voltage regulation, their regulation characteristics vary with their operation means, and the randomness and volatility of renewable power generation will also influence the optimization and regulation of voltage in the distribution network. This paper proposes a multi-time scale reactive power optimization and regulation method for distribution networks in a multi-source interactive environment. Firstly, the voltage regulation characteristics of distributed PV systems, decentralized ES, and distributed WT are analyzed. Based on this analysis, then a multi-time scale voltage optimization scheme for distribution networks using MPC method is proposed, which optimizes the voltage regulation strategies for each distributed resource in a rolling manner. Furthermore, an event-triggered real-time voltage zoning control strategy based on voltage sensitivity is proposed to address the real-time sudden voltage overlimit problems. The modified IEEE 33-node system is used to verify the performance of proposed method, simulation results indicate that the issue of voltage overruns at distribution network nodes has been improved, and the intraday rolling optimization yields results that are more realistic compared to the day-ahead optimization method.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

We consider the problem of coordinating the charging of an entire fleet of electric vehicles (EV), using a model-free approach, i.e. purely data-driven reinforcement learning (RL). The objective of the RL-based control is to optimize charging actions, while fulfilling all EV charging constraints (e.g. timely completion of the charging). In particular, we focus on batch-mode learning and adopt fitted Q-iteration (FQI). A core component in FQI is approximating the Q-function using a regression technique, from which the policy is derived. Recently, a dueling neural networks architecture was proposed and shown to lead to better policy evaluation in the presence of many similar-valued actions, as applied in a computer game context. The main research contributions of the current paper are that (i)we develop a dueling neural networks approach for the setting of joint coordination of an entire EV fleet, and (ii)we evaluate its performance and compare it to an all-knowing benchmark and an FQI approach using EXTRA trees regression technique, a popular approach currently discussed in EV related works. We present a case study where RL agents are trained with an epsilon-greedy approach for different objectives, (a)cost minimization, and (b)maximization of self-consumption of local renewable energy sources. Our results indicate that RL agents achieve significant cost reductions (70--80%) compared to a business-as-usual scenario without smart charging. Comparing the dueling neural networks regression to EXTRA trees indicates that for our case study's EV fleet parameters and training scenario, the EXTRA trees-based agents achieve higher performance in terms of both lower costs (or higher self-consumption) and stronger robustness, i.e. less variation among trained agents. This suggests that adopting dueling neural networks in this EV setting is not particularly beneficial as opposed to the Atari game context from where this idea originated.

Bearing fault diagnosis is crucial for ensuring the stable operation of mechanical equipment. With the continuous development of deep learning technology, Convolutional Neural Networks (CNNs) have demonstrated significant advantages in the field of fault diagnosis. This paper proposes a new method that combines various CNN architectures to improve the accuracy of bearing fault diagnosis. We designed five different convolutional network structures, including SerConv, ResConv, One-Shot Aggregation Convolution (OSAConv), Cross-Stage Aggregation Convolution (CSAConv), and MD-DAConv. Experimental results on the Case Western Reserve University (CWRU) bearing dataset show that the proposed method exhibits high accuracy and robustness in fault diagnosis. The results indicate that strategies such as multi-directional, multi-scale, and residual connections play a crucial role in enhancing the depth and breadth of feature extraction, while simple and effective feature fusion and information transmission mechanisms are key to ensuring the robustness and generalization ability of the model.

Passive balancing is a traditional choice for lithium-ion battery packs although it is regarded as highly inefficient. One opportunity to improve traditional balancing in sub-medium size battery packs is to combine two balancing methods: passive and active. Statistical analysis have been performed to rationalize battery pack division in smaller packs and use of higher level selective charging method to decrease losses of passive balancing. An experimental balancing prototype have been designed and tested for efficiency. Results indicate energy performance degradation if cells of the pack are with low capacity variation. Proposed balancing approach could improve performance under high cell mismatch conditions.

Electric Vehicles (EVs) are the need of the hour due to growing climate change problems linked with the transportation sector. Battery Thermal Management System (BTMS), which is accountable for certifying safety and performance of lithium-ion batteries (LiB), is the most vital part of an EV. LiB has auspicious gravimetric energy density but the heat generation due to chemical reactions inside a LiB during charging and discharging causes temperature rise which has a direct effect on LiB performance and safety. This study specifically focuses on aircooled BTMS, defines different types of air-cooled BTMS (active and Passive), discusses limitations associated with air-cooled BTMS, and investigates different optimization techniques and parameters to improve performance of air-cooled BTMS. Maintaining temperature within optimum range and uniform temperature distribution between cells of a battery pack are the major design parameters for improving the performance and efficiency of air-cooled BTMS. Various optimization techniques including cell arrangement with a battery pack, air-flow channel optimization, and air inlet/outlet position variations are discussed and each technique is thoroughly reviewed. Finally, it’s noted that passive air-cooled BTMS is not that effective for long-distance vehicles so most researchers shifted their focus toward active air-cooled BTMS. Active air-cooled BTMS requires a lot of power for effective performance. Lastly, the most recent field of air-cooled BTMS technology which is Air-Hybrid BTMS is discussed and declared a very promising solution for overcoming major limitations associated with air-cooled BTMS.

This study evaluates eight-year ownership costs for battery electric vehicles (BEV) versus non-plugin hybrid vehicles using forecasting to estimate future electricity and conventional gasoline prices and incorporating these in a multiple design of experiments simulation. Results suggest that while electric vehicles are statistically dominant in terms of variable costs over an 8-year life-span, high-performance hybrid non-plugins achieve variable fuel costs nearly as good as low-performing electric vehicles (those attaining only 3 miles per kilowatt hour) and that these hybrid acquisition costs are (on average) lower yet the vehicles retain higher residual values. In general, the six smallest ownership costs are split evenly between hybrid and electric vehicles; however, inflation for conventional regular gasoline is estimated to outstrip inflation per kilowatt hour. Thus, non-plugin hybrid cars are likely to require considerably more advanced engineering to keep pace.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

With an increasing adoption of Battery Electric Bus (BEB) fleets, developing a reliable charging schedule is vital to a successful migration from their fossil fuel counterparts. In this paper, a Simulated Annealing (SA) implementation is developed for a charge scheduling framework for a fixed-schedule fleet of BEBs that utilizes a proportional battery dynamics model, accounts for multiple charger types, allows partial charging, and further considers the total energy consumed by the schedule as well as peak power use. Two generation mechanisms are implemented for the SA algorithm denoted as the "quick" and "heuristic" implementations, respectively. The model validity is demonstrated by utilizing a set of routes sampled from the Utah Transit Authority (UTA) and comparing the results against two other models: the BPAP and the Qin-Modified. The results presented show that both SA techniques offer a means of generating operationally feasible schedules quickly while minimizing the cost of operation and considering battery health.

This paper presents a thermal runaway prognosis scheme based on the big-data platform and entropy method for battery systems in electric vehicles. It can simultaneously realize the diagnosis and prognosis of thermal runaway caused by the temperature fault through monitoring battery temperature during vehicular operations. A vast quantity of real-time voltage monitoring data was collected in the National Service and Management Center for Electric Vehicles (NSMC-EV) in Beijing to verify the effectiveness of the presented method. The results show that the proposed method can accurately forecast both the time and location of the temperature fault within battery packs. Furthermore, a temperature security management strategy for thermal runaway is proposed on the basis of the Z-score approach and the abnormity coefficient is set to make real-time precaution of temperature abnormity.

The study involves the creation of a solar-powered car that can travel up to 70 km with a maximum speed of 35.7 km/h, the vehicle mass is 300 kg. It stores some energy, which is then converted into electric energy that can be consumed by other electrical appliances, making it an electrical energy generator. The two back wheels are equipped with 3,000 W electric motors to enable movement. When the vehicle moves, power dissipates due to resistances that must be overcome to move it. Auxiliary components and the battery powering the system also require energy, resulting in not all power being transmitted to the electric vehicle's wheels. This article aims to create a prototype of the electric vehicle model. A model of the photovoltaic system, considering the geographic coordinates and solar parameters of the location, as well as the BLDC motor and vehicle dynamics, is required to examine the component behavior based on the observable parameters. These pa-rameters consist of the resistive torque, angular speed, and resistance values that need to be overcome to evaluate the electric vehicle's performance. Once the lost power has been determined, the remaining power will be allocated to power other electrical devices. The variations in the parameters considered are crucial for the performance of an electric vehicle equipped with a photovoltaic and mechanical power supply system, as one of the sources of our prototype is mechanical and provides 400 W of power.

This work targets the development of a mobility control system for high-speed series hybrid electric tracked vehicles, which operate with independent traction motors for each track. The scope of the research encompasses the modeling of the series hybrid powertrain specific to military tracked vehicles, as well as an in-depth analysis of their dynamic behavior. Subsequently, the study conducts a critical review of the mobility control approaches sourced from literature, identifying key techniques relevant to high-inertia vehicular applications. Building on the foundational models, the study puts forward a robust closed-loop mobility control system aimed at ensuring precise and stable off-road vehicle operations. The system's resilience and adaptability to a variety of driving conditions are emphasized, with a particular focus on handling maneuvers such as steering and pivoting, which are challenging operations for tracked vehicle agility. The performance of the proposed mobility control system is tested through a series of simulations, covering a spectrum of operational scenarios. These tests are carried out in both offline simulation settings, which permit meticulous fine-tuning of system parameters, and real-time environments that replicate actual field conditions. The simulation results demonstrate the system's capacity to improve vehicular response and highlight its potential impact on the future designs of mobility control systems for the heavy-duty vehicle sector, particularly in defense applications.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

In order to serve the online monitoring of the aging state of high-voltage (HV) cables, a novel method based on impedance spectroscopy has been proposed. Firstly, the method uses the Debye model to restore the dielectric response of the insulating material from the mechanism. Secondly, based on the transmission line equation, a calculation model for the impedance spectroscopy of HV cables was established. Then, the characteristics of the impedance spectroscopy under different overall aging and local deterioration states were analyzed. Further, the simulation analysis of the influence of factors such as load factor, length, metal resistivity, and geometric parameters on the impedance spectroscopy was carried out. Finally, diagnostic criteria were proposed, which are divided into two major categories: known cable parameters and unknown cable parameters. If the geometric parameters are known, the aging state can be determined using the resonance peak values and the resonance peak frequencies. If the geometric parameters are unknown, it is necessary to test the impedance spectroscopy in the healthy condition of the cable as the baseline curve. By comparing the impedance spectroscopy of the cable under test with the baseline curve, the aging development trend of the cable can also be determined.

The volatility and uncertainty associated with the high proportion of wind and PV output in the new power system significantly impact power and energy balance, making it challenging to accurately assess the risks related to renewable energy abandonment and supply guarante. Therefore, a probabilistic power and energy balance risk analysis method based on distributed robust optimization is proposed. Firstly, the affine factor and the flexible ramp reserve capacity of thermal power are combined to establish a probabilistic index, which serves to characterize the risk associated with power and energy balance. Drawing upon the principles of conditional value at risk theory, the risk indexes of load shedding power and curtailment power under a certain confidence probability are proposed. Secondly, the probability distribution fuzzy sets of uncertain variables are constructed using the distributionally robust method to measure the Wasserstein distance between different probability distributions. Finally, aiming at minimizing the operation cost of thermal power, the risk cost of power abandonment and the risk cost of load shedding, a distributed robust optimal scheduling model based on flexible ramp reserve of thermal power is established.

We describe a forecast system based on the Weather Research and Forecasting (WRF) model for the prediction of high-impact weather events affecting power utilities, particularly conditions conducive to wildfires. The system was developed for Pacific Gas and Electric Corporation (PG&E) to operationally forecast conditions in Northern and Central California. It was established in 2014 and has been periodically improved. In the current configuration, WRF forecasts are routinely performed multiple times each day on a 2-km grid, and the results are used as input to wildfire fuel moisture, fire probability, and wildfire spread models. Components of the system include a stochastically perturbed ensemble; an annually updated reanalysis covering more than 30 years; and validation against PG&E’s extensive mesonet and other observing networks. We describe the development and validation of the next operational edition. Configurations tested include irrigation triggered by crop growing season and an ensemble-based approach with intelligently sub-selected Global Ensemble Forecast System (GEFS) members. The latter approach allows for enhanced uncertainty sampling in WRF forecasts and can greatly improve WRF forecasts when calibrated by observations.

Induction motors are the most numerous and significant dynamic loads in power systems. In transient voltage stability analysis, dynamic equivalent models are commonly used to simplify the representation of a group of induction motors. This paper presents an method for the grouping and aggregation of induction motors at a common bus. Firstly, grouping rules were provided for clustering induction motors into several subgroups based on the mechanical principles of rotor force and motion, and Aggregation Rules were provided for aggregating a motor subgroup into a single-unit model based on the relationship between voltage drop and power transmission in distribution networks. Secondly, guided by the grouping rules, high-speed remaining electromagnetic torque and low-speed remaining electromagnetic torque were defined as new clustering indicators, and an adaptive K-means clustering method using silhouette coefficient verification was provided to obtain the optimal motor subgroups. Thirdly, guided by the Aggregation Rules, a dynamic equivalent method was further provided to obtain the equivalent single-unit model from a motor subgroup. Lastly, a transient voltage stability simulation in a typical distribution network was presented to illustrate that the proposed clustering and equivalent methods are more reasonable, accurate, and effective than traditional methods, as the obtained model has better dynamic characteristics and can more accurately reproduce the process of voltage collapse.

In this paper, we examined the temperature variations of key constituents during the operational cycle of a custom-built electric vehicle. The vehicle was made employing a motor of 10kW, a KLS7275D controller, and a lithium-ion battery. Temperature sensors for monitoring was affixed to the motor, controller, and battery, facilitating a comprehensive analysis of thermal behaviors. A controlled 20 minute driving tests encompassing both high and low speeds were executed to scrutinize temperature variations. Our findings reveal that the controller exhibited the most substantial temperature fluctuation compared to the battery and motor. Results shows the importance of thermal management strategies for components to ensure optimal driving performance and component reliability in electric vehicles.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The lack of defect image data is one of the main factors affecting the accuracy of supervised deep learning-based defect detection models. In response to the insufficient training data of defect images with complex backgrounds such as rust and surface oil leakage in substation equipment, leading to poor performance of the detection model, this paper proposed a novel adversarial deep learning model for substation defect generation: ADD-GAN. In comparison to existing generative adversarial networks, this model generates defect images based on effectively segmented local areas of substation equipment images, avoiding image distortion caused by global style changes. Additionally, the model utilizes a joint discriminator for overall image and defect image to address the issue of low attention to local defect areas, thereby improving the loss of image features. This enhances the overall quality of generated images as well as locally generated defect images, ultimately improving image realism. Experimental results demonstrate that the YOLOV7 object detection model trained on the dataset generated using the ADD-GAN method achieves an mAP of 81.5% on the test dataset, representing an improvement of 9.6% over the original dataset, 5.7% over traditional augmentation methods, and 7% over typical adversarial deep learning methods. This confirms that the ADD-GAN method can generate a high-fidelity dataset of substation equipment defects.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

The transportation industry is rapidly transitioning from Internal Combustion Engine (ICE) based vehicles to Electric Vehicles (EVs) to promote clean energy. However, large-scale adoption of EVs can compromise the reliability of the power grids by introducing large uncertainty in the demand. Demand response with a controlled charge scheduling strategy for EVs can mitigate such issues. In this paper, a deep reinforcement learning- based charge scheduling strategy is developed for individual EVs by considering user’s dynamic driving behavior and charging preferences. The temporal dynamics of user’s anxiety about charging the EV battery is rigorously addressed. A dynamic weight allocation technique is applied to continuously tune user’s priority for charging and cost-saving with respect to charging duration. The sequential charging control problem is formulated as a Markov decision process, and an episodic approach to the deep deterministic policy gradient (DDPG) algorithm with target policy smoothing and delayed policy update techniques is applied to develop the optimal charge scheduling strategy. A real-world dataset that captures user’s driving behavior, such as arrival time, departure time, and charging duration, is utilized in this study. The extensive simulation results reveal the effectiveness of the proposed algorithm in minimizing energy cost while satisfying user’s charging requirements.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

The link between the world of communication and the world of racing is provided by telemetry systems in electric racing cars. These systems send real-time data about the vehicle’s behavior and systems to enable informed decisions during the race. The aim of this research was to integrate telemetry into the battery bank of a racing electric vehicle to find the optimal values of current and voltage that optimize the charging process, thus improving the vehicle’s performance in competition using Response Surface Analysis. Particularly, the telemetry system consisted of an Arduino Mega, a digital wattmeter, and temperature sensors, all installed in the vehicle. Once the telemetry data was obtained, a response surface design was adapted with current, voltage, and temperature as factors, varying from low to high values, with the objective function being to minimize the battery’s charging time. Applying the response surface methodology and the steepest descent algorithm, it was found that all factors significantly affect the charging time, with the minimum charge time being 6961 seconds, obtained with a current of 2.4 amps and voltages of 50.5 volts and 43.6 volts.

With the rapid development of electric vehicles, the infrastructure for charging stations is also expanding quickly, and the failure rate of charging piles is increasing. To address the effective operation and maintenance of charging stations, a method based on the XGBoost algorithm for electric vehicle DC charging stations is proposed. An operation and maintenance system is con-structed based on state analysis, considering the operation status of the charging station and users' charging habits. Factors such as driving and charging habits, road traffic, and charging station equipment are taken into account. The training sample data is established using historical data, online monitoring data, and external environmental data, and the charging station status evaluation model is trained using the XGBoost algorithm. Based on the condition assessment results, a risk assessment model is established in combination with fault parameters. Risk tracking of the charging station is conducted using the lack of power supply (ENC), evaluating the risk level of each station, and determining the operation and maintenance order. The optimal opera-tion and maintenance model for DC charging stations, aimed at achieving both economic and reliable goals, is constructed to determine the operation and maintenance schedule for each sta-tion. The results of the case study demonstrate that the state evaluation and operation and maintenance strategy can significantly improve the reliability of the system and the overall ben-efits of operation and maintenance while meeting the required standards.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Under the goal of carbon peak and carbon neutrality, the carbon emission reduction of the automobile industry has attracted more and more attention in recent years. Electric vehicle has the dual attributes of power load and energy storage unit. With the increase of the number of electric vehicles, reducing carbon emissions through the collaborative interaction between electric vehicle and power network will become an important way to control carbon emissions in the automotive field. In this study, an optimization model of emission reduction benefits based on integrated development of electric vehicle and power grid is proposed, which explores the best technical way of synergy between power grid and electric vehicle, achieves the best carbon reduction effect and provides a model basis for large-scale demonstration application. Numerical simulations based on the real case in Beijing are conducted to validate the effectiveness of the proposed method.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

The development of technology that combines supercapacitors and lithium-ion batteries by externally connecting them in parallel is ongoing. This study examines the correlation between the volume ratio and electrical characteristics of a cell made by internally connecting a battery capacitor with Li4Ti5O12 as the anode active material and a supercapacitor in parallel. It was found that increasing the volume occupied by the battery capacitor in the cell led to increased cell energy and resistance, resulting in decreased output characteristics. Conversely, increasing the volume occupied by the supercapacitor in the cell led to a decrease in the IR drop during discharge and cell temperature when evaluating cycle characteristics with a current of 20C. The study also examined the behavior of the current distributed during the charging and discharging process based on the volume ratio of the supercapacitor and the battery capacitor. Analyzing the correlation between the volume ratio and electrical characteristics of supercapacitors and battery capacitors could potentially lead to the development of a new type of energy storage device.

Battery/Supercapacitor(SC) current tracking control is a key issue for hybrid energy storage system (HESS) in electric vehicles. An innovative passivity-based L2-gain adaptive control (PBL2AC) based on port-controlled Hamiltonian model with dissipativity (PCHD) for reference current tracking and bus voltage stability in HESS is presented. The developed PCHD model has considered both parameter variations and external disturbances. By using L2-gain disturbance attenuation, the PBL2AC ensures robust reference current tracking and stable bus voltage. Moreover, adaptive mechanism is adopted to estimate the electrical parameters. To validate the proposed control scheme for HESS, simulations and experiments were done and compared with traditional PID and sliding mode control under several typical driving cycles, and results show that the effectiveness of the proposed controller can be confirmed.

In this study, we focused on the eco-driving of electric vehicles (EVs). The target vehicle is an electric bus developed by our research team. Using the parameters of the bus and speed pattern optimization algorithm, we derived the EV eco-driving speed pattern. Compared to eco-driving of internal combustion engine vehicles (ICVs), we found several different characteristics. We verified these characteristics with actual vehicle driving test data of the target bus, and the results confirmed its rationality. The EV eco-driving method can improve electricity consumption by about 10% - 20% under the same average speed.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

With the rapid development of electric vehicles, the infrastructure for charging stations is also expanding quickly, and the failure rate of charging piles is increasing. To address the effective op-eration and maintenance of charging stations, a method based on the XGBoost algorithm for electric vehicle DC charging stations is proposed. An operation and maintenance system is constructed based on state analysis, considering the operation status of the charging station and users' charging habits. Factors such as driving and charging habits, road traffic, and charging station equipment are taken into account. The training sample data is established using historical data, online monitoring data, and external environmental data, and the charging station status evaluation model is trained using the XGBoost algorithm. Based on the condition assessment results, a risk assessment model is established in combination with fault parameters. Risk tracking of the charging station is conducted using the lack of power supply (ENC), evaluating the risk level of each station, and determining the operation and maintenance order. The optimal operation and maintenance model for DC charging stations, aimed at achieving both economic and reliable goals, is constructed to determine the op-eration and maintenance schedule for each station. The results of the case study demonstrate that the state evaluation and operation and maintenance strategy can significantly improve the relia-bility of the system and the overall benefits of operation and maintenance while meeting the re-quired standards.

(1) Background: We aim to construct a machine learning (ML) algorithm to predict the risk of distant metastasis (DM) of T1 and T2gallbladder cancer (GBC); (2) Demographic and clinical pathological data of T1 and T2 GBC patients were extracted from the National Institutes of Health (NIH)’s Surveillance, Epidemiology, and End Results (SEER) database between 2004 and 2015 to develop seven ML algorithm models. Models were evaluated based on accuracy, precision, recall rate, F1- score, and area under the receiver operating characteristic curve (AUC); (3) Results:A total of 4371 patients were included in the study, of whom 764 (17.4%) developed DM. Multivariate logistic regression showed that age, histology, tumor size, T and N stages were independent factors in GBC with DM. A novel nomogram was established to predict distant metastasis in early T stage GBC patients. Evaluation indicators of the best model Random Forest (RF) were as follows: accuracy (0.828), recall rate (0.862), precision (0.811), F1- score (0.836), and AUC value (0.913); (4) Con-clusions: The RF model constructed in this study could accurately predict distant metastasis in GBC patients, which may provide clinicians with more personalized clinical decision-making recom-mendations.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

The diffusion of electric vehicles (EVs) can be sustained by the presence of integrated solutions offering parking and clean power supply. The recourse to DC systems allows to better integrate EV bidirectional energy exchange, photovoltaic panels and energy storage. In this paper, a methodology for optimal techno-economic sizing of a DC-microgrid for covering EV mobility needs is carried out. It is based on the definition of different scenarios of operation, according to typical EV usage outlooks and environmental conditions. In each scenario, optimal operation is carried out by means of a specific approach for EV commitment on different stations. The sizing procedure is able to handle the modular structure of microgrid devices. The proposed approach is applied to a case study of envisaged EV service fleet for Bari port authority.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

To enable the deployment of battery-electric vehicles (BEV) as passenger cars in the private transport sector, a suitable charging infrastructure is crucial. In this paper a methodology for efficient spatial distribution of charging infrastructure is evaluated by investigating a scenario with a market penetration of BEVs of 100 percent (around 1.3 million vehicles). It aims towards the development of various charging infrastructure scenarios - including public and private charging - which are suitable to cover the charging demand. Therefore, these scenarios are investigated in detail with focus on number of public charging points, their spatial distribution, the available charging power and the necessary capital costs. For the creation of those charging infrastructure scenarios a placement model is developed. It uses the data of a MATSim (Multi-Agent Transport Simulation) traffic simulation of the metropolitan area of Berlin to evaluate and optimize different distributions of charging infrastructure. The model uses a genetic algorithm and the principle of multi-objective optimization. The capital cost of the charging points and the mean detour car drivers must cover additionally are used as optimization criteria. Using these criteria should lead to cost efficient infrastructure solutions which provide high usability at the same time. The main advantage of the method selected is that multiple optimal solutions with different characteristics can be found and suitable solutions can be selected by using other criteria subsequently. The optimized charging infrastructure solutions show capital costs between 624 and 2950 million euro. Users must cover an additionally mean detour of 254m to 590m per charging process to reach an available charging point. According to the results a suitable ratio between charging points and vehicles is between 11:1 and 5:1. A share of fast charging infrastructure (&gt;50kW) of less than ten percent seems to be sufficient, if it is situated at main traffic routes and highly frequented places.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

The contamination of soils by mineral oils presents a significant environmental challenge, particularly due to the widespread use of petroleum products in various industrial sectors. This study investigates the efficiency of microwave heating compared to conventional resistance heating for the thermal desorption of mineral oil from contaminated soils. Experimental results demonstrated that microwave heating offers superior performance in terms of pollutant removal efficiency, energy consumption, and preservation of soil's physical and chemical properties. The study further conducted a kinetic analysis of the desorption process, revealing that microwave heating follows a first-order kinetic model and requires lower activation energy than conventional methods. The findings suggest that microwave-assisted thermal desorption is a highly effective and energy-efficient technology for soil remediation, providing a potential alternative to conventional techniques. This research offers valuable insights into optimizing thermal desorption processes for environmental remediation, with implications for broader applications in soil treatment.

The meticulously engineered powertrain mounting system of hybrid-electric vehicles plays a critical role in minimizing vehicle vibrations and noise, thereby enhancing the longevity of vital powertrain components. However, developing and designing such a system demands substantial time and financial investments due to intricate analysis and modeling requirements. To tackle this challenge, this study integrates data-mining technology into the design and optimization processes of the powertrain mount system. The research focuses on the powertrain mounting system of a transverse four-cylinder hybrid-electric vehicle, employing the CRISP-DM (Cross-Industry Standard Process for Data Mining) methodology to establish a data-mining prediction model for mounting stiffness. This model utilizes three data mining algorithms—Multi-SVR, MRTs, and MLPR—assessing their predictive accuracy concerning mounting system stiffness estimation. A comparative analysis reveals that the MRTs algorithm outperforms others as the most effective prediction model. The proposed predictive model elucidates the quantifiable correlation between vibration isolation performance and installation stiffness, overcoming complexities associated with traditional modeling approaches. Applying this model in powertrain mounting system design showcases the efficacy of the CRISP-DM-based approach, significantly enhancing design efficiency without compromising prediction accuracy.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

This study developed a three-dimensional kinematic and dynamic model of a center-driven linkage system (CDLS). Force analysis was conducted to determine the required driving torque to ensure that the input link of the CDLS rotates at a constant speed with a certain angular velocity, even in the presence of frictional resistance torque. The primary objective was to optimize the maximum angular acceleration of the output links to reduce wiper noise. This optimization can enhance the stability of the linkage system while maintaining its operational functionality. In the adopted methodology, the frames of the fixed links are assumed to remain unchanged, and the input link is considered to operate at a constant angular speed and have a constant length. To meet standard vehicle windshield wiper requirements, 10 constraints were imposed on the optimization problem, which was solved using the differential evolution method. The lengths of both output links were reduced by over 10% after optimization.

This paper presents design and optimization of a small-size electromagnetic induction heating control system powered by a 3.7V-900mAh lithium battery and featuring an LC series resonant full bridge inverter circuit, which can be used in small size materials heating applications, such as micro medical devices. The effects of resonant capacitance, inductor wire diameter, heating tube material and wall thickness are studied to maximize the heating rate of the workpiece and meantime reduce the temperature rise of the NMOS transistor. The optimal circuit configuration meeting the design requirements was finally identified via comparing the operational parameters and NMOS transistor loss under different circuit conditions. The validation experiments were conducted on a designed electromagnetic induction smoking devices. The results indicate that under an output current of 4.6A, the heating tube can reach up to the temperature target of 250℃ within 11 seconds, and all NMOS transistors stay below 50°C in a 5 minutes heating process.

This work presents an innovative application of optimal control theory to the strategic scheduling of battery storage in the day-ahead electricity market, with a focus on enhancing profitability while factoring in battery degradation. The study incorporates in the optimisation framework the cost of battery capacity degradation, the effects of capacity degradation and internal resistance degradation into dynamics. We employ a continuous-time representation of the dynamics, in contrast with many other studies that use a discrete-time approximation with rather coarse intervals. We adopt an equivalent circuit model coupled with empirical degradation parameters to simulate a battery cell’s behaviour and degradation mechanisms with good support from experimental data. Utilising direct collocation methods with mesh refinement allows for precise numerical solutions to the complex, nonlinear dynamics involved. Through a detailed case study of Belgium’s day-ahead electricity market, we determine the optimal charging and discharging schedules under varying objectives: maximizing net revenues, profits considering capacity degradation, and profits considering both capacity degradation and internal resistance increase due to degradation. The results demonstrate the viability of our approach and underscore the significance of integrating degradation costs into the market strategy for battery operators, alongside its effects on the battery’s dynamic behaviour. Our methodology extends previous work by offering a more comprehensive model that empirically captures the intricacies of battery degradation, including a fine and adaptive time domain representation, focusing on the day-ahead market, and utilising accurate direct methods for optimal control. The paper concludes with insights into the potential of optimal control applications in energy markets and suggestions for future research avenues.

This paper proposes an optimization method for the scheduling of a multi-energy virtual power plant supply-demand balance in the power market environment of Jiangxi Province. The objective of this method is to enhance the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method comprehensively considers the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Additionally, real-time market price feedback is integrated to achieve accurate allocation of power supply and demand. Through a case study of a multi-energy virtual power plant in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply-demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

The purpose of this work is to present an adaptive sliding mode luenberger state observer with improved disturbance rejection capability and better tracking performance under dynamic conditions. The sliding hyperplane is altered by incorporating the estimated disturbance torque with the stator currents. Also, the effects of parameter detuning on the speed convergence is observed and compared with the conventional disturbance rejection mechanism. The entire drive system is first built in simulink environment. Then, the simulink model is integrated with RT-Lab blocksets and implemented in a relatively new real-time environment using OP4500 real-time simulator. Real-time simulation and testing platforms have succeeded offline simulation and testing tools due to their reduced development time. The real-time results validate the improvement in the proposed state observer and also correspond to the performance of the actual physical model.

The greenhouse gases and air pollution generated by extensive energy use have exacerbated climate change. An electric-bus (e-bus) transportation system favors reducing pollution and carbon emissions. This study analyzed the minimization of construction costs for an all battery-swapping public e-bus transportation system. A simulation was conducted according to existing timetables and routes. Daytime charging was incorporated during the hours of operation; the two parameters of the daytime charging scheme were the residual battery capacity and battery-charging energy during various intervals of daytime peak electricity hours. The parameters were optimized using three algorithms: particle swarm optimization (PSO), a genetic algorithm (GA), and a PSO–GA. This study observed the effects of optimization on cost changes (e.g., number of e-buses, on-board battery capacity, number of extra batteries, charging facilities, and energy consumption) and compared the plug-in and battery-swapping e-bus systems. The results revealed that daytime charging can reduce the construction costs of both systems. In contrast to the other two algorithms, the PSO–GA yielded the most favorable optimization results for the charging scheme. Finally, according to the cases investigated and the parameters of this study, the construction cost of the plug-in e-bus system was lower than that of the battery-swapping e-bus system.

In the ongoing shift towards electric vehicles (EVs) primarily utilizing lithium-ion battery technology, a significant population of hybrid electric vehicles (HEVs) remains operational, reliant on established NiMH battery systems. Over the last twenty years, these HEVs have generated a substantial quantity of NiMH batteries that are either inoperable, experiencing performance degradation, or approaching the end of their service life. This results in a twofold challenge: a growing volume of environmentally hazardous waste due to the difficulty of NiMH battery reclamation, and escalating maintenance costs for HEV owners necessitated by replacement battery purchases. Patent WO2015092107A1, published in 2015, proposed a "Method for regenerating NiMh batteries." This method claims the ability to restore NiMH batteries to their original functionality. However, a comprehensive review of relevant scientific literature fails to identify any empirical evidence supporting the efficacy of the regeneration technique detailed in the patent. Within this context, this paper presents a detailed analysis and evaluation of the feasibility of the aforementioned patented method. To achieve this objective, the authors propose a prototype constructed utilizing NiMH battery cells sourced from a Toyota Prius. The experimental results obtained from this prototype demonstrate the potential for battery regeneration using the proposed method. These findings offer a promising solution for mitigating the challenges associated with NiMH battery disposal and maintenance within the HEV domain.