Since the electro-hydraulic servo shaking table exists many nonlinear elements, such as, dead zone, friction and blacklash, its acceleration response has higher harmonics which result in acceleration harmonic distortion, when the electro-hydraulic system is excited by sinusoidal signal. For suppressing the harmonic distortion and precisely identify harmonics, a combination of the adaptive linear neural network and least mean M-estimate (ADALINE-LMM), is proposed to identify the amplitude and phase of each harmonic component. Namely, the Hampel’s three-part M-estimator is applied to provide thresholds for detecting and suppressing the error signal. Harmonic generators are used by this harmonic identification scheme to create input vectors and the value of the identified acceleration signal is subtracted from the true value of the system acceleration response to construct the criterion function. The weight vector of the ADALINE is updated iteratively by the LMM algorithm, and the amplitude and phase of each harmonic, even the results of harmonic components, can be computed directly online. The simulation and experiment are performed to validate the performance of the proposed algorithm. According to the experiment result, the above method of harmonic identification possesses great real-time performance and it has not only good convergence performance but also high identification precision.

Observer-based control is the most commonly used method in the control of electro-hydraulic servo system (EHSS) with uncertainties, but it suffers from the drawback of low accuracy under the influence of large external load forces and disturbances. To address this problem, this paper proposes a novel compensation function observer-based backstepping sliding mode control (BSMC) approach to achieve high-accuracy tracking control. In particular, the model uncertainties, including nonlinearities, parameter perturbations and external disturbances are analyzed and treated together as a lumped disturbance. Then, a fourth-order compensation function observer (CFO) is constructed, which fully utilizes the system state information to accurately estimate the lumped disturbance. On this basis, the estimate of the lumped disturbance is incorporated into the design of an backstepping sliding mode controller, allowing the control system to compensate for the disturbance effect. The stability of the closed-loop control system under the CFO and BSMC is rigorously proven through the use of Lyapunov theory, which guarantees that all the tracking error signals converge exponentially to the origin. Comparative simulations are carried out to show the effectiveness and efficiency of the proposed approach, i.e., compared with PID and ESO-based BSMC methods, the tracking accuracy is improved by 99.93% and 99.76%, respectively.

Multi-level shaking table tests were performed on 1:3 reduced scale two-story RC IMRF frames conforming to ACI-318-19. The exterior joints lacked shear reinforcement to assess the viability of the ACI model recommended for determining the design shear strength of the beam-column joint panel. The Northridge-1994 earthquake accelerogram was input to the frame for multi-level shaking table testing. Plastic hinges developed in beams under base input motion with a maximum acceleration equal to 0.40g. The exterior joints incurred extensive damage under base input motion with a maximum acceleration equal to 0.70g. The frame achieved displacement ductility and overstrength factors equal to 2.40 and 2.50 respectively. This gives a response modification factor equal to 6. The satisfactory performance of the frame is attributed to the high efficiency of the beam-column joint, which was confined by spandrel beams on two faces, and the high strength of the concrete. The inherent minimal confinement is sufficient to ensure good seismic behavior. The analysis confirmed overstrength equal to 1.58 for joint shear strength in comparison to the design strength determined using the ACI model. The data might serve as a reference for calibrating and validating numerical modeling techniques for performance evaluation, which are crucial in the context of performance-based engineering.

In general, the stone pagoda structures with discontinuous surfaces are vulnerable to lateral forces and are severely damaged by earthquakes. After the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the earthquakes damaged numerous stone pagoda structures due to slippage, rotation and the separation of stacked stone. To evaluate seismic resistance of masonry stone pagoda structure, we analyzed the seismic behavior of stone pagoda structure using shaking table test. Shaking frequency, permanent displacement, maximum acceleration, rocking, and sliding were assessed. Responses to simulations of the Bingol, Gyeongju, and Pohang earthquakes based on Korean seismic design standard (KDS 41 17 00) were analyzed for return periods of 1,000 and 2,400 years. We found that the type of stylobate affected the seismic resistance of stone pagoda structure. When the stylobates were stiff, seismic energy was transferred from lower to upper regions of the stone pagoda, which mainly resulted in deformation of the upper region. When the stylobates were weak, earthquake energy was absorbed in the lower regions; this was associated with large stylobate deformations. The lower part of tower body was mainly affected by rocking, because the structural members were slender. The higher part of the stone pagoda was mainly affected by sliding, because the load and contact area decreased with height.

Model-based fault diagnosis serves as a powerful technique for addressing fault detection and isolation issues in control systems. However, diagnosing faults in closed-loop control systems is more challenging due to their inherent robustness. This paper aims to detect and isolate actuator and sensor faults in the cascade electro-hydraulic control system of a turbofan engine. Based on the fault characteristics, we design a robust unknown perturbation decoupling residual generator and an optimal fault observer specifically for the inner and outer control loops to detect potential faults. To locate the faults, we analyze the steady-state propagation laws of actuator and sensor faults within the loops using the final value theorem. Based on this, we establish the minimal-dimensional fault influence distribution matrix specific to the cascade turbofan engine control system. Subsequently, we construct the normalized residual vectors and monitor its vector angles against each row of the fault influence distribution matrix to isolate faults. Experiments conducted on an electro-hydraulic test bench demonstrate that our proposed method can accurately locate four typical faults of actuators and sensors within the cascade electro-hydraulic control system. This study enriches the existing fault isolation methods for complex dynamic systems, and lays the foundation for guiding component repair and maintenance.

The improvement of energy efficiency of hydraulic systems remains to be an essential challenge for the industry, and the demand for more sustainable solutions is increasing. A main focus in this endeavor is the ability to eliminate or strongly reduce the use of throttle control valves which have been the preferred control element in industrial hydraulic systems for decades. Components have been subject to continuous evolution, and current industrial grade hydraulic pumps and motors are both efficient and reliable. Even though few percentages of energy efficiency can still be achieved, the main achievements in terms of efficiency is associated with novel system designs rather than further development of components. An area subject to increasing attention is the field of variable-speed displacement control, allowing to avoid the main control valve throttle losses. Systems using this technology are, however, mainly developed as standalone drive systems, necessitating maximum force, speed and power installed in each axis, with limited hydraulic power distribution capability as compared to valve controlled systems. An emerging field addressing this challenge is so-called electro-hydraulic variable-speed drive networks which allow to completely eliminate the use of control valves and enables power sharing both electrically and hydraulically, potentially reducing the necessary installed power in many cases. The idea of such a technology was first proposed in 2022, and so far developments reported in literature have mainly been of theoretical nature. This article presents the first ever experimental results for a dual cylinder electro-hydraulic variable-speed drive network prototype. The prototype has been developed for an industrial application, but has initially been implemented in a laboratory testbench. Extensive data acquisition has been conducted while subject to the associated industrial motion cycle, under different load conditions. The data is further used in combination with models to predict the total efficiency of the drive network prototype under higher loads than what could be achieved in the laboratory, suggesting a total efficiency from the electric supply to the cylinder pistons of 68 %. Re-configuring the prototype to a known standalone drive system structure implies comparable efficiencies. Finally, the drive network is theoretically compared to a valve drive solution, generally suggesting the prototype drive network to provide efficiency improvements of at least 40 % in comparison.

The ground consists of many layers of soil with different properties. The propagation speed and path of seismic waves are affected by different soil layers. It is necessary to understand that layered soil exhibits different dynamic behaviors and responses under the action of seismic waves. This study utilized weathered soil and silica sand as materials to create multi-layered soil conditions with varying degrees of compaction. By conducting 1 g shaking table test on multi-layered soil, the interaction and influence between different soil layers under different earthquake conditions were observed. The approach of numerical analysis aims to validate the experimental results and provide an in-depth understanding of the dynamic behaviors of multi-layered soil grounds during seismic events. The results of this study show that the amplification effect of seismic waves is related to the number of soil layers and the degree of compaction of the soil layers. This indicates that the multi-layered soil ground and the behavior of the soil layers play an important role in the propagation and impact of seismic waves, and this amplification effect is of great significance in actual seismic disaster risk assessment and design.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

In order to coordinate the damping performance and energy regenerative performance of energy regenerative suspension, this paper proposes a structure of vehicle semi-active energy regenerative suspension with electro-hydraulic actuator (EHA). In light of the proposed concept, a specific energy regenerative scheme is designed and the mechanical properties test is carried out. Based on the test results, the parameter identification for the system model is conducted using recursive least squares algorithm. On the basis of system principle, the nonlinear model of the semi-active energy regenerative suspension with EHA is built. Meanwhile, LQG control strategy of the system is designed. And then the influence of the main parameters of EHA on the damping performance and energy regenerative performance of suspension is analyzed. Finally, the main parameters of EHA actuator are optimized via genetic algorithm. The test results show that when sinusoidal is input at the frequency of 2Hz and the amplitude of 30mm, the spring mass acceleration RMS value of optimized EHA semi-active energy regenerative suspension is reduced by 22.23% and energy regenerative power RMS value is increased by 40.51%, which means while meeting the requirements of certain vehicle ride comfort and driving safety, energy regenerative performance is improved significantly.

When the epipelic algae group growing on the concrete inclined side wall, which is typical of urban rivers and open diversion channels, enters the water flow, it will seriously affect the func-tion of the rivers or the channels. It is urgent to predict the transport capacity of epipelic algae group with water flow. However, the current research on the transport of pollutants is mostly based on mathematical models, and the study of the transport of flake epipelic algae group is extremely rare. A generalized hydrodynamic experimental model of a flume with sidewall epi-pelic algae group was established. Through a series of hydraulic experiments, the physical movement form and transport capacity of the suspended epipelic algae group on the side wall of the channel were studied qualitatively and quantitatively by taking the thickness, sheet size and flow rate of the epipelic algae group as the influencing factors. The key influencing factors of the suspension of epipelic algae are clarified, so as to quantitatively analyze the critical conditions of its suspension. Through flow scheduling, the probability of epipelic algae gathering some-where is increased. It provides a theoretical basis for realizing the long-distance migration of epipelic algae and optimizing the mathematical model.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

In the era of the post-quantum Internet of Things (IoT), the implementation of anti-quantum cryptographic algorithms in numerous terminals can successfully defend against prospective quantum computing assaults. Lattice-based cryptography can withstand quantum computing attacks, making it a viable substitute for the currently prevalent classical public-key cryptographic technique. Nevertheless, the algorithm’s significant time complexity will result in a substantial computational burden on the edge computing chip in the IoT terminal. The computation of polynomial multiplication is the most demanding task in lattice-based cryptographic algorithms. Therefore, the investigation into efficient methods for calculating polynomial multiplication is highly important. Quick number theory transformations (NTT) are a widely employed technique to accelerate polynomial multiplication. This study presents a hardware implementation of an efficient number theory transformation. We utilize a multi-level pipeline architecture in the design to accomplish parallel calculations and execute it on a low-profile Artix7-XC7A100T FPGA device. The performance evaluation results demonstrate that our implementation significantly enhances performance and reduces resource usage compared to other existing proposals on the same platform. We suggested NTT core can be implemented in edge computing chips to enhance computational speed due to its small and low-latency design. The experimental results show that the proposed design, which supports both NTT and inverse NTT, achieves 417-Megahertz and consumes only 541-LUTs on Artix-7 XC7A100T.

During the 16th and 17th centuries, Latin American cities adopted earthen construction techniques from European colonizers. As a result, rammed earth (RE) buildings now occupy an important place in Latin America's cultural heritage. However, earthquakes around the world have shown that unreinforced earthen constructions are highly vulnerable. For several years, researchers in northern South America have been proposing a technique that consists of installing confining steel plates (or wooden elements) on both sides of the RE walls forming a grid. This system has shown excellent performance in controlling seismic damage and increasing strength and ductility capacity. Although researchers have tested full-scale one- and two-story earthen walls under pseudo-static loading in the laboratory, and one- and two-story earthen walls at 1:1 and 1:2 scale on uniaxial and biaxial shaking tables, the behavior of a complete reinforced module (one- or two-story) on a shaking table has never been assessed. The present study presents the results of shaking table tests performed on two-story RE modules at 1:4 scale. The experimental data indicate that the retrofit system with confining steel strips was effective in reducing the seismic damage of earthen constructions. In addition, the comparison of the results of the 1:4 scale tests with the 1:2 and 1:1 scale tests previously conducted by the researchers, shows that the acceleration levels of the equivalent prototypes are in the same order of magnitude for the three scales.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

The objective of this study, which is divided into two parts, is twofold: to address long standing challenges in the sensing of atmospheric turbulence-induced wavefront aberrations in strong scintillation conditions via comparative analysis of several basic scintillation resistant wavefront sensing (SR-WFS) architectures and iterative phase retrieval (IPR) techniques (Part I, this paper), and to develop a framework for the potential integration of SR-WFS techniques into practical closed-loop non-astronomical atmospheric adaptive optics (AO) systems (Part II). In this paper we consider basic SR-WFS mathematical models and phase retrieval algorithms, tradeoffs in sensor design and phase retrieval technique implementation, and methodologies for WFS parameter optimization and performance assessment. The analysis is based on wave-optics numerical simulations imitating realistic turbulence-induced phase aberrations and intensity scintillations, and optical field propagation inside SR-WFSs. Several potential issues important for practical implementation of SR-WFS and IPR techniques such as requirements for phase retrieval computational grid resolution, tolerance with respect to optical element misalignments, and the impact of camera noise and input light non-monochromaticity are also considered. Results demonstrate that major wavefront sensing requirements desirable for AO operation in strong intensity scintillations can potentially be achieved by transitioning to novel SR-WFS architectures based on iterative phase retrieval techniques.

The shaft hydropower plant (SHPP) is a novel hydraulic concept for low-head hydropower sites with several environmental and operational advantages over conventional layouts. However, the first two projects implementing this concept have shown comparatively high construction costs and project risks. Therefore, further optimization is required to the economic attractiveness and enabling broader market adoption. Initial model tests recommend a square-shaped shaft inlet with a three-sided approach flow for low-loss and fish-friendly inflow conditions. Yet, this design requires significant space for structural implementation and may be unsuitable for use with multiple shafts or as an extension of non-powered dams and weirs. This research paper presents the application of a computational fluid dynamics simulation setup to evaluate the hydraulic per-formance of various design configurations, especially, alternative design layouts with one-sided approach flow without further physical model tests,. The simulation setup is calibrated against observations including head loss and velocity measurements from the physical model tests, and its satisfactory performance enables the analysis of alternative design layouts. This aims to derive the most significant design parameters for achieving the desired hydraulic conditions at the intake. Increasing the flow depth before the intake and enlarging the inlet area have the most significant impact, while increasing the overflow of the front gate has the least significant effect.. The chosen CFD application is deemed suitable for hydraulic design optimization and provides guidance on the key parameters to focus on for tailored site-specific design development.

Digital twins are an emerging technology that could be harnessed for the digitalization of the industry. Steel industry systems contain a large number of electro-hydraulic components, as proportional valves. An input-output model for a novel water proportional cartridge valve is derived from physical modelling based on fluid mechanics, dynamics, and electrical principles. The valve is a two-stage valve with two 2/2-way water proportional valves as the pilot stage and a marginally stable poppet-type cartridge valve as the main valve. The orifice equation, which is based on Bernoulli principles, is approximated by a polynomial which makes parameter estimation easier and makes modelling possible without measuring pressure of the varying control volume situated in the pilot stage part of the valve. Data were collected when the valve was operating as a component in a closed-loop system as part of a press-mill machine in a steel manufacturing plant. Parameter estimation was made by convex optimization with physical constraints to overcome problems caused by poor system excitation. For comparison, a simple linear model was derived and the least squares method used for parameter estimation. A thorough estimation of the parameters relative errors is presented. The model contains 5 parameters related to the design parameters of the valve. The modelled position output is in good agreement with experimental data for training and test data. The model can be used for real time monitoring of the valve’s status by the model parameters. One of the model parameters varies linearly with production cycles. Thus, aging of the valve can be monitored.

High-precision displacement sensing has been widely used across from both scientific researches and industrial applications. The recent interests in developing micro-opto-electro-mechanical systems (MOEMS) have given rise to an excellent platform for miniaturized displacement sensors. Advancement in this field during past years is now yielding integrated high-precision sensors which show great potential in applications ranging from photoacoustic spectroscopy to high-precision positioning and automation. In this review, we briefly summarize different techniques for high-precision displacement sensing based on MOEMS, and discuss the challenges for future improvement.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Flow over a cluster of three equally spaced circular cylinders was studied by numerical simulation on base of the turbulent mode k-kl-ω for two incidence angles β=0° and 60°, at different Reynolds number,in this paper, flow interference pattern characteristics between cylinders, characteristics of force parameters and Strouhal number of each cylinder with different spacing ratios ranging from 1.5 to 4 at Re 8×104, 2×105and 2×106 had been obtained. At incidence angle β=0° and 60°, the wake was nearly symmetric if S/D≥2.0; at β=60°,S/D=1.5 and Re=2×105, the asymmetric periodic flow pattern occurred in the wake region which leaded to the significant effect on the surface mechanical parameters and Strouhal number which was found for the first time; the periodic flow regime of the wake region also occurred at S/D=1.35 and 1.5, without the same phenomenon at S/D=1.7 and 2.0; the phenomenon of periodic flow regime of the wake region was intrinsic and related to Reynolds number and space ratio. in addition, characteristics of force parameters of three cylinders mainly were affected by the interference between cylinders, at 1.5<S/D<4, which leaded to that the drag coefficient of three cylinders reduced with different Reynolds numbers. At incidence angle 60°, in subcritical and critical regime, the Strouhal numbers of the upstream cylinders were more than that of single cylinder, and with the enlargement of spacing ratio, the Strouhal number decreased; for the downstream cylinder , the Strouhal number is far less than that of single cylinder and with the enlargement of spacing ratio, the Strouhal number increases, which were another prominent flow inference influence. The results indicated the effect of flow interference between cylinders subjected to a cross flow over a cluster of three equally spaced cylinders on the flow pattern,surface mechanical parameters and Strouhal number.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

With the advances in industry and commerce, passengers have become more accepting of environmental sustainability issues; thus, more people now choose to travel by bus. Government administration constitutes an important part of bus transportation services as the government gives the right-of-way to transportation companies allowing them to provide services. When these services are of poor quality, passengers may lodge complaints. The increase in consumer awareness and developments in wireless communication technologies have made it possible for passengers to easily and immediately submit complaints about transportation companies to government institutions, which has brought drastic changes to the supply-demand chain comprised of the public sector, transportation companies, and passengers. This study proposed the use of big data analysis technology including systematized case assignment and data visualization to improve management processes in the public sector and optimize customer complaint services. Taichung City, Taiwan was selected as the research area. There, the customer complaint management process in public sector was improved, effectively solving such issues as station-skipping, allowing the public sector to fully grasp the service level of transportation companies, improving the sustainability of bus operations, and supporting the sustainable development of the public sector-transportation company-passenger supply chain.

This study investigated the effectiveness of virtual reality (VR) technology in table tennis education compared to traditional training methods. A 12-week randomized controlled trial was conducted with 120 participants divided equally between VR and traditional training groups. Performance metrics, learning motivation, and satisfaction were assessed at regular intervals. Results demonstrated significant advantages of VR training, with the VR group showing superior improvements in serve accuracy (23.5% vs. 15.8%, p < 0.001), rally endurance (increase of 8.2 vs. 5.7 shots, p < 0.01), and overall skill scores (18.7 vs. 13.2 points improvement, p < 0.001). The VR group also exhibited higher increases in learning motivation (23.5% vs. 12.8%, p < 0.001) and satisfaction (31.5% vs. 18.7%, p < 0.001). Subgroup analysis revealed particular benefits for novice players and younger participants. These findings suggest that VR technology offers a promising approach to enhance table tennis education, potentially revolutionizing sports training methodologies. Future research should focus on long-term skill retention and the optimization of VR training protocols.

In order to help the transportation industry achieve the goal of carbon peak and carbon neutrality, this study is based on the selection of eight variables, such as population size, per ca pita GDP, personal vehicle ownership, passenger and freight turnover, and green space coverage, as the factors influencing the carbon emissions of the transportation industry in Jiangsu Province, and the prediction and analysis of the transportation carbon emission trends from 2000 to 2021, and the prediction and analysis of the carbon emissions of the transportation industry and the time of the peak of the carbon emissions in Jiangsu Province. The trend of transportation carbon emissions from 2000 to 2021 was predicted and analyzed, and the carbon emissions and peak time of carbon emissions in the transportation industry in Jiangsu Province were predicted and analyzed. Comparing the predicted results with other models to verify the accuracy of the results, it was found that the WOA-SVM model had the smallest error among several models. On this basis, targeted measures are proposed to accelerate the process of carbon peak and ensure the smooth achievement of carbon neutrality goals in Jiangsu Province. The results indicate that under the current policy measures, the peak carbon emissions in Jiangsu Province will occur in 2038, with a peak of 48.72 million tons. Jiangsu Province should actively adopt energy-saving and emission-reduction measures, build a green and low-carbon transportation development model, and achieve the carbon peak target ahead of schedule.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

Water quality assessment stands as a fundamental step in water resource management. In addition to substances and organisms present in the water, land use and land cover are two factors affecting also water quality. This study analyzed the correlation and influence between water quality and land use and land cover in the Miranda River Basin (MRB) and the natural wetlands in the Pantanal Biome. Using a watershed-wide approach, results suggested that water quality management policies can be considered in terms of sub-basins (smaller planning units). The Water Quality Index (WQI) was considered GOOD or EXCELLENT throughout the MRB. It was observed that the natural wetlands have the capacity to contribute to improve WQI, with reductions in thermotolerant coliforms and turbidity; however, high values were found for thermotolerant coliforms, a temporal increasing trend of biochemical oxygen demand (BOD), and a reduction in dissolved oxygen and total phosphorus. Conversely, it was found in these flooded areas a trend of decrease in dissolved oxygen and an increase in BOD concentrations. Natural wetlands play important hydrological and ecological roles in water quality, storing, removing, and cycling nutrients. They are highly relevant areas for defining watershed management and conservation strategies, environmental protection, and providing ecosystem services.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

Proper identification of oriented knots and 2-component links requires a precise link nomenclature. Motivated by questions arising in DNA topology, this study aims to produce a nomenclature unambiguous with respect to link symmetries. For knots, this involves distinguishing a knot type from its mirror image. In the case of 2-component links, there are up to sixteen possible symmetry types for each topology. The study revisits the methods previously used to disambiguate chiral knots and extends them to oriented 2-component links with up to nine crossings. Monte Carlo simulations are used to report on writhe, a geometric indicator of chirality. There are ninety-two prime 2-component links with up to nine crossings. Guided by geometrical data, linking number and the symmetry groups of 2-component links, a canonical link diagram for each link type is proposed. All diagrams but six were unambiguously chosen ( $8_1^{2}5$ , $9_5^2$ , $9_3^{2}4$ , $9_3^{2}5$ , $9_3^{2}9$ , and $9_4^{2}1$ ). We include complete tables for prime knots with up to ten crossings and prime links with up to nine crossings. We also prove a result on the behavior of the writhe under local lattice moves.

In a dual-inertia system based on permanent magnet synchronous motor (PMSM), the elastic transmission mechanism, such as reducer and coupling, is prone to mechanical resonance, which reduces the precision of servo system transmission. Model prediction and introduction of state feedback are effective methods to suppress mechanical resonance, but the control parameters de-pend on the mechanical parameters of the system. Therefore, mechanical parameter identification is very necessary. In this paper, a forgetting factor recursive least square method is used to identify the mechanical parameters of the dual-inertia elastic system. Firstly, the mathematical model of the dual-inertia system is established and reasonably simplified. Then, the discrete function of the identification algorithm is constructed, and the motor speed and electromagnetic torque are sam-pled to achieve the on-line identification of the main mechanical parameters of the dual-inertia system, and the influencing factors of the identification accuracy are analyzed. Finally, simulations and experiments are carried out to verify the effectiveness of the algorithm.

Eutrophication, a global concern, impacts water quality, ecosystems, and human health. It’s crucial to monitor algal blooms in freshwater reservoirs, as they indicate the trophic condition of a waterbody through Chlorophyll-a (Chla) concentration. Traditional monitoring methods, however, are expen-sive and time-consuming. Addressing this hindrance, we developed models using remotely sensed data from the Sentinel-2 satellite for large-scale coverage, including its bands and spectral indexes, to estimate the Chla concentration on 149 freshwater reservoirs in Ceará, Brazil. Several machine learning models were trained and tested, including k-nearest neighbours, random forests, extreme gradient boosting, the least absolute shrinkage, group method of data handling (GMDH), and sup-port vector machine models. A stepwise approach determined the best subset of input parameters. Using a 70/30 split for the training and testing datasets, the best-performing model was the GMDH, achieving an R2 of 0.91, MAPE of 102.34%, and RMSE of 20.38 g/L, which are values consistent with the ones found in the literature. Nevertheless, the predicted Chla concentration values were most sensitive to the red, green, and near infra-red bands.

The ever-growing concerns about global warming and the rapid depletion of fossil fuels have triggered a rising interest in research for cleaner, more efficient and cost-effective energy generation. Organic Rankine cycle systems have immense potential to become a strong alternative to conventional methods of energy generation. However, such systems’ efficiency is limited by the performance of the incorporated gas expanders or prime movers. Conventional gas expanders often utilize ports or cam-operated valves. Ported expanders offer limited efficiency and controllability, and produce high emissions causing a large amount of heated and compressed gas to be wasted. Cam-operated valves, in contrast, increase expansion performance compared to ported expanders, however, they have no variability and adaptability to changes in system parameters such as gas pressure, temperature, dryness fraction, and load variation to name a few. On a positive note, this issue can be addressed by adopting a variable timing and fast-operating, control valve with an accurate and adaptive control mechanism at the expander inlet. A properly designed and controlled valve can greatly improve the system performance of gas expanders and pave the way for an efficient low-cost alternative energy generation. This manuscript provides a comparative review of recent progress on the design, modeling, optimization, and control aspects of valves for gas expanders. A clear pathway on the scope of further development is also drawn based on the present state of the art.

'Cv 'Doña María' table grape is a high-quality table grape variety included in the Protected Designation of Origin (PDO) of the European Union "The bagged grape of the Vinalopó." The PDO stipulates that grape clusters must be protected with paper bags from inclement weather and insects, which helps enhance the final grape quality. However, 'Doña María' is a variety prone to high shattering in the late stages of ripening on the vine and during postharvest. Inorganic calcium treatments are one of the most commonly used tools to reduce this disorder, but the translocation of this mineral from veraison onward has been questioned. In this study, five applications were performed, from veraison to harvest, using sorbitol-chelated calcium (0.7 % + 1.0 %), Ca(NO3)2 (Ca) at 0.7% and sorbitol at 1%. It was observed that bagged grapes (not wetted with the solutions) only increased the concentration of total and bound calcium when treated with Sorbitol-Ca. This resulted in reduced berry drop during cultivation and postharvest and improved fruit firmness. Additionally, it reduced grape metabolism indicators such as respiration rate, weight loss, malic acid degradation, prevented abscisic acid (ABA) and malondialdehyde (MDA) accumulation, and favored the accumulation of secondary metabolites such as total polyphenols, increased antioxidant activity, and sugar content. The application of sorbitol-chelated calcium is an effective and safe tool that enhances fruit quality and prevents losses due to shattering during postharvest.

Table grape quality is of importance for consumers and thus for producers. The objective quality determination is usually destructive and very simple with the assessment of only a couple of parameters. This study proposed to evaluate the possibility of hyperspectral imaging to characterize table grapes quality through its sugar, total flavonoid and total anthocyanin contents. Different pre-treatments (WB, SNV, 1st and 2nd derivative) and different methods were tested: PLS with full spectra, then Multiple Linear Regression (MLR) were realized after selecting the optimal wavelengths thanks to the regression coefficients (-coefficients) and the Variable Importance in Projection (VIP) scores from the full spectra. All models were good showing that hyperspectral imaging is a relevant method to assess sugar content and global phenolic content. The best model was dependent on the variable. The best models were from the full spectra and with the 2nd derivative pre-treatment for TSS; from VIPs optimal wavelengths using SNV pre-treatment for Total Flavonoid and total Anthocyanin content. Thus, relevant models were proposed using the full spectra, as well as specific windows and wavelengths in order to reduce the data sets and limit the data storage to enable an industrial use.

In this paper, a voice coil motor (VCM) actuated fast tool servo (FTS) system is developed for diamond turning. To guide motions of the VCM actuator, a crossed double parallelogram flexure mechanism is selected featuring totally symmetric structure with high lateral stiffness. To facilitate the determination of the multi-physical parameters, analytical models of both electromagnetic and mechanical systems are developed. The designed FTS with balanced stroke and natural frequency is then verified through the finite element analysis. Finally, the prototype of the VCM actuated FTS is fabricated and experimentally demonstrated to have a stroke of ±59.02 μm and a first natural frequency of 253 Hz. By constructing a closed-loop control using PID controller with the internal-model based resonant controller, the error for tracking a harmonic trajectory with ±10 μm amplitude and 120 Hz frequency is obtained to be ±0.2 μm, demonstrating the capability of the FTS for high accuracy trajectory tracking.

This article investigates hydraulic percolation in saturated porous media, focusing on containment systems using sheet pile walls and gravity concrete dams. The Laplace equation, which governs hydraulic flow in porous media, is solved using the Finite Element Method through the ANSYS software. The modeling of the porous media employs a planar quadratic element called Plane 55, originally used for thermal problems, composed of four nodes and one hydraulic degree of freedom per node. The numerical results of the water pressure acting on the hydraulic structure, flow rate, and hydraulic gradient at the outlet of the porous media are compared with results obtained in the technical-scientific literature using flow nets. Two different methodologies are used to obtain the rate of seepage: by using the average hydraulic velocity or by calculating the integral of the hydraulic gradient perpendicular to the flow area. Both methodologies are compared and validated in the numerical simulations. This work also demonstrates the importance of mesh refinement for obtaining the flow rate in the studied hydraulic systems.

The construction time of concrete structures in hydraulic tunnels is long, the construction environment is complex, and there are many influencing factors. The requirements for construction quality are high, not only to meet the strength requirements, but also to meet the design requirements of erosion resistance, crack resistance, and seepage resistance according to its specific operating environment. Therefore, evaluating the construction quality of concrete structures in hydraulic tunnels is of great significance. Considering the randomness and fuzziness of factors affecting the construction quality of concrete structures in hydraulic tunnels, this paper proposes a comprehensive evaluation model based on Combined Weighting (CWM) and Uncertainty Measurement Theory (UM). The IAHP method and CRITIC method are used to determine the subjective and objective weights of evaluation indicators, combined weighting is based on the principle of minimum entropy, and the UM method is used to evaluate the construction quality level. Finally, taking a hydraulic tunnel as an example, its construction quality grade is calculated to be III according to the evaluation model proposed in this paper, which matches with the engineering reality, and a comparative study is made with the mixture element topology theory at the same time. It is verified that the evaluation model can scientifically and reasonably evaluate the construction quality level of concrete structures in hydraulic tunnels.

Hydraulic fracturing has enabled production from unconventional reservoirs in the U.S., but production rates often decline sharply, limiting recovery factors to under 10%. This study optimizes the CO2 huff-n-puff process for multistage-fractured horizontal wells in Wolfcamp A formation in the Delaware Basin. The potential for enhanced oil recovery and CO2 sequestration simultaneously was addressed using a coupled geomechanics-reservoir simulation. Geomechanical properties were derived from a 1D mechanical earth model and integrated into reservoir simulation to replicate hydraulic fracture geometries. The fracture model was validated using a robust production history matching. Fluid phase behavior analysis refined the equation of state, and 1D slim tube simulations determined a minimum miscibility pressure of 4300 psi for CO2 injection. After the primary production phase, various CO2 injection rates were tested from 1 to 25 MMSCFD/well, resulting in incremental oil recovery ranging from 6.3% to 69.3%. Different injection, soaking, and production cycles were analyzed to determine the ideal operating condition. The optimal scenario improved cumulative oil recovery by 68.8% while keeping the highest CO2 storage efficiency. The simulation approach proposed by this study provides a systematic workflow for evaluating and optimizing CO2 huff-n-puff in hydraulically fractured wells, enhancing the recovery factor of unconventional reservoirs.

This study fabricated piezoelectric fibers of polyvinylidene fluoride (PVDF) with graphene using near-field electrospinning (NFES) technology. A uniform experimental design table U*7 (7^4 ) was applied, considering weight percentage (1-13 wt%), distance between needle and disk collector (2.1-3.9 mm), and applied voltage (14.5-17.5 kV). We optimized the parameters using electrical property measurements and the Kriging response surface method. Adding 13 wt% graphene significantly improved electrical conductivity, increasing from 17.7 μS/cm for pure PVDF to 187.5 μS/cm. The fiber diameter decreased from 21.4 μm in PVDF/1% graphene to 9.1 μm in PVDF/13% graphene. Adding 5 wt% graphene increased the β-phase content by 6.9%, reaching 65.4% compared to pure PVDF fibers. Material characteristics were investigated using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), contact angle measurements, and tensile testing. Optimal parameters included 3.47 wt% graphene, yielding 15.82 mV voltage at 5 Hz and 5 N force (2.04 times pure PVDF). Force testing showed a sensitivity (S) of 7.67493 log(mV/N). Fibers were attached to electrodes for piezoelectric sensor applications. Results affirmed enhanced electrical conductivity, piezoelectric performance, and mechanical strength. The optimized piezoelectric sensor could be applied to measure physiological signals, such as attaching it to the throat under different conditions to measure the output voltage. The force-to-voltage conversion facilitated subsequent analysis.

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

The growing amount of data demands methods that can gradually learn from new samples. However, it is not trivial to continually train a network. Retraining a network with new data usually results in a known phenomenon, called “catastrophic forgetting.” In a nutshell, the performance of the model drops on the previous data by learning from the new instances. This paper explores this issue in the table detection problem. While there are multiple datasets and sophisticated methods for table detection, the utilization of continual learning techniques in this domain was not studied. We employed an effective technique called experience replay and performed extensive experiments on several datasets to investigate the effects of catastrophic forgetting. Results show that our proposed approach mitigates the performance drop by 15 percent. To the best of our knowledge, this is the first time that continual learning techniques are adopted for table detection, and we hope this stands as a baseline for future research.

The paper presents a new type of hydraulic clutch operating with magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. The hy-draulic clutch system of its own design with MR working fluid and a rotating magnetic field lo-cated is designed. The principle of this clutch is to use a rotating magnetic field created by an al-ternating current electromagnet to set the MR fluid in motion. In the tests of the hydraulic clutch with a rotating magnetic field, MR fluid produced on their own, consisting of solid iron particles of various diameters mixed with a silicone oil, are used as working fluids. The rheological properties of MR fluids are assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating the magnetic field of its own design. The char-acteristics of the hydraulic clutch with MR working fluid and the rotating magnetic field are tested on a specially built test stand. As a result of the research, it has been found that the torque transmitted by the clutch is the greater, the higher the rotational speed of the magnetic field and the lower the rotational speed of the beaker in which the working fluid is placed, and that the greatest torque occurs for the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch working with MR fluid and the rotating magnetic field can be applied to stationary power transmission system similarly to an eddy current clutch.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Recent research on fractional order control laws has introduced the fractional calculus concept into the field of control engineering. As described herein, we apply fractional order LQR control to a current-controlled attractive-force type magnetic levitation system, which is a strongly nonlinear and unstable system, to investigate its control performance through experimentation. First, to design the controller, a current-controlled attractive-force type magnetic levitation system expressed as an integer-order system is extended to a fractional order system expressed using fractional order derivatives. Then target value tracking control of levitated objects is achieved by adding states, described by the integrals of the deviation between the output and the target value, to the extended system. Next, a fractional order LQR controller is designed for the extended system. For state-feedback control such as fractional order servo LQR control, which requires information of all states, a fractional order state-observer is configured to estimate fractional order states. Simulation results demonstrate that fractional order servo LQR control can achieve equilibrium point stabilization and enable target-value tracking. Finally, to verify the fractional order servo LQR control effectiveness, experiments using the designed fractional order servo LQR control law are done with comparison to conventional integer-order servo LQR control.

Tables in the document image are one of the most important entities since they contain crucial information. Therefore, accurate table detection can significantly improve information extraction from tables. In this work, we present a novel end-to-end trainable pipeline, HybridTabNet, for table detection in scanned document images. Our two-stage table detector uses the ResNeXt-101 backbone for feature extraction and Hybrid Task Cascade (HTC) to localize the tables in scanned document images. Moreover, we replace conventional convolutions with deformable convolutions in the backbone network. This enables our network to detect tables of arbitrary layouts precisely. We evaluate our approach comprehensively on ICDAR-13, ICDAR-17 POD, ICDAR-19, TableBank, Marmot, and UNLV. Apart from the ICDAR-17 POD dataset, our proposed HybridTabNet outperforms earlier state-of-the-art results without depending on pre and post-processing steps. Furthermore, to investigate how the proposed method generalizes unseen data, we conduct an exhaustive leave-one-out-evaluation. In comparison to prior state-of-the-art results, our method reduces the relative error by 27.57% on ICDAR-2019-TrackA-Modern, 42.64% on TableBank (Latex), 41.33% on TableBank (Word), 55.73% on TableBank (Latex + Word), 10% on Marmot, and 9.67% on UNLV dataset. The achieved results reflect the superior performance of the proposed method.

The human-readable simplicity with which the CSV format was devised, together with the absence of a standard that strictly defines this format, has allowed the proliferation of several variants in the dialects with which these files are written. The latter has meant that the exchange of information between data management systems, or between countries and regions, requires human intervention during the data mining and cleansing process. This has led to the development of various computational tools that aim to accurately determine the dialects of CSV files, in order to avoid data loss at data loading stage in a given system. However, the dialect detection is a complex problem and current systems have limitations or make assumptions that need to be improved and/or extended. This paper proposes a method for determining CSV file dialects through table uniformity, a statistical approach based on table consistency and records dispersion measurement along with the detection of data type over each field. The new method has a 100\% accuracy on a dataset with 148 CSV files composed of samples coming from a data load testing framework and some others added as verification of the parsing routines. In tests on truly messy data, the proposed solution outperforms the state-of-the-art tool by achieving an improvement of about 10\% in the accuracy with which dialects are detected. Furthermore, the proposed method is accurate enough to determine dialects by reading only ten records, requiring more data to disambiguate those cases where the first records do not contain the necessary information to conclude with a dialect determination.

The hydraulic fracturing is studied by using dimensional analysis. A universal scaling law of the hydraulic fracturing is obtained. This simple relation has not been seen in the literature.

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

Nutrient profiling (NP) models that assess nutrient density of foods can help remedy micronutrient deficiencies. We used NP methods to identify the most nutrient-rich foods in the 2019 FAO/INFOODS Western Africa Food Composition Table (WAFCT). The WAFCT had complete data for 909 foods. Three versions of the well-established Nutrient Rich Food (NRF) model were used: 1) the original NRF9.3; 2) a new NRF6.3 based on 6 priority micronutrients (iron, zinc, calcium, folate, vitamin A, vitamin B12); and 3) NRF 15.3, based on 15 nutrients to encourage (NRF6.3 nutrients + vitamin D, vitamin E, vitamin C, vitamin B1, vitamin B2, vitamin B3, vitamin B6, copper, and magnesium). Data analyses used one-way ANOVAs and independent t-tests, with significance at α=0.05. Animal-source foods were rated higher by NRF6.3 priority micronutrient and NRF15.3 NP models than by the NRF9.3 model. African indigenous vegetables had higher protein content and higher nutrient density compared to non-indigenous vegetables. African indigenous grains had higher nutrient density compared to non-indigenous grains. Though animal-source foods received some of the highest scores, NP models adapted to the West African context showed that African indigenous vegetables and grains were also nutrient rich. Indigenous foods could be important sources of priority micronutrients for the region.

The isotopic and nuclear techniques discussed, namely: Fallout Radionuclide, Fingerprint, and Isotope Hydrology, are linked to the evaluation of soil and water degradation processes. A traditional literature review was conducted to gain the most comprehensive understanding of both the current state of the art and the subject matter, with the aim of proposing a hypothesis that integrates the synergistic convergence of these techniques in order to offer results that are more reliable. A case study is presented as a synthesis of the preceding discussion.

Production of electricity using hydro-kinetic tidal turbines has many challenges that must to be overcome to ensure reliable, economic and practical solutions. Energy from flowing water is converted by a system comprising: the turbine rotor blades, a gearbox, an electrical generator, control systems, power electronics, export cables, and a connection to the electricity grid. To date these have often been modelled using simulations of independent systems, lacking bi-directional, real-time, coupling. This approach leads to critical effects being missed. Turbulence in the flow, results in large velocity fluctuations around the blades, causing rapid variation in the shaft torque and generator speed, and consequently in the voltage seen by the power electronics and consequently the export power quality. The resulting poor quality power may be unacceptable to the grid. Conversely, grid frequency and voltage changes can also cause the generator speed to change, resulting in changes to the shaft speed and torque and consequently changes to the lift and drag forces acting on the blades. Clearly, fully integrated, bi-directional, models are needed. Here we present two fully coupled models which use different approaches to model the hydrodynamics of rotor blades. The first model uses Blade Element Momentum Theory (BEMT), resulting in an efficient tool for turbine designers. The second model also uses BEMT combines this with an actuator line model of the blades coupled to an unsteady computational fluid dynamics (CFD) simulation. This simulation, implemented in OpenFOAM, uses an energy balance to compute the shaft speed. Both the BEMT and CFD models are coupled to an Open Modellica model of the electro-mechanical system. Both models have been used to simulate the performance of a 1.2m diameter, scale model, of a three bladed horizontal axis tidal turbine tested in the University of Edinburgh FloWave Ocean Energy Research Facility. The turbulent flow around the blades and the mechanical-electrical variables during the stable period of operation are analysed. Time series and tabulated average values of mechanical thrust, power, torque, and rotational speed as well as electrical variables of generator power, electromagnetic torque, voltage and current are presented for the coupled system simulation. The relationship between the mechanical and electrical variables and the results from both tidal turbine approaches are discussed. Our comparison shows that while the BEMT model provides an effective design tool (leading to slightly more conservative designs), the CFD/BEMT simulations provide more accurate predictions of the blade loads which can be especially important in assessing fatigue on the blades (though at an increased computational cost).

A rigorous model for the electron is presented by generalizing the Coulomb's Law or Gauss's Law of electrostatics, using a unified theory of electricity and gravity. The permittivity of the free-space is allowed to be variable, dependent on the energy density associated with the electric field at a given location, employing generalized concepts of gravity and mass/energy density. The electric field becomes a non-linear function of the source charge, where concept of the energy density needs to be properly defined. Stable solutions are derived for a spherically symmetric, surface-charge distribution of an elementary charge. This is implemented by assuming that the gravitational field and its equivalent permittivity function is proportional to the energy density, as a simple first-order approximation, with the constant of proportionality referred to as the Unifield Electro-Gravity (UEG) constant. The stable solution with the lowest mass/energy is assumed to represent a ``static'' electron without any spin. Further, assuming that the mass/energy of a static electron is half of the total mass/energy of an electron including its spin contribution, the required UEG constant is estimated. More fundamentally, the lowest stable mass of a static elementary charged particle, its associated classical radius, and the UEG constant are related to each other by a dimensionless constant, independent of any specific value of the charge or mass of the particle. This dimensionless constant is numerologically found to be closely related to the the fine structure constant. This possible origin of the fine structure constant is further strengthened by applying the proposed theory to successfully model the Casimir effect, from which approximately the same above relationship between the UEG constant, electron's mass and classical radius, and the fine structure constant, emerges.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

The current scenario of radioactive waste management requires innovative and automated solutions to ensure effectiveness and safety. In response to this need, the PI3SO (Proximity Imaging System for Sort and Segregate Operations) project was proposed. It is a gamma radiation proximity scanner system for radioactive waste with the primary goal of speeding up some aspects of the waste management cycle while reducing direct human operations. The system will provide proximity imaging for hot spot finding and spectral analysis for radiological characterization, enabling semiautomatic recognition, sorting and separation of radioactive waste. The core of the proposed scanning system consists of an array of 128 CsI(Tl) scintillators, 1 cm3 size, coupled with silicon photomultipliers (SiPM), installed on a motorized bridge sliding along a suitable table in order to scan the materials under investigation.

This study is aimed to point out the possible application of the Enzyme-Linked ImmunoSorbent Assay (ELISA) test on table olives. Because olives, like many other foods, are not free from mycotoxin contamination, the main focus of this work was assessing the presence or absence of aflatoxins and ochratoxin A. The work was carried out in two phases. In the first phase, tests were carried out on commercial olives to assess the efficacy of the method and the kit (Veratox® 'Neogen' and AgraQuant® 'Romer Labs') by comparing them with the Liquid Chromatography coupled to a mass-mass spectrometer (LC-MS/MS); in order to understand if there were any interferences in antigen-antibody recognition; subsequently, mycotoxins were inoculated on the same samples with a known quantity, in order to assess the concentrations obtained and compare them to the expected ones. The second step involved modifying the method, so to improve the recovery of inoculated mycotoxins in the samples under study. Afterwards we evaluated the presence of mycotoxins in table olives supplied in the project. The results showed the effectiveness of the ELISA test, especially in the mycotoxin recovery phase. Indeed, after the modification of the mycotoxin extraction method, recoveries increased from 55% to over 70% for aflatoxins, and from 40% to over 55% for ochratoxin A. When analysing the samples provided by the above-mentioned company, the results showed some false positives, in particular in relation to ochratoxin A ’s analysis, mainly related to the first sample submission. Taking this into account, the ELISA test can be considered as an initial screening method applicable as a control programme for the evaluation of mycotoxins in olives which helps by saving time and costs. It should always be kept in mind that, if positive values should emerge, the LC-MS/MS analysis should be carried out.

We present a method using contour integration to derive definite integrals and their associated infinite sums which can be expressed as a special function. We give a proof of the basic equation and some examples of the method. The advantage of using special functions is their analytic continuation which widens the range of the parameters of the definite integral over which the formula is valid. We give as examples definite integrals of logarithmic functions times a trigonometric function. In various cases these generalizations evaluate to known mathematical constants such as Catalan’s constant and π

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

Approximately 20% of the world's population resides in coastal areas at risk of rising sea levels due to climate change. This could lead to severe weather events and ecological impact on critical infrastructure. To combat the effects of water-based environmental forces on the land, hard engineering methods such as seawalls have been utilized. However, a more sustainable solution is emerging in nature-based engineering, which involves growing vegetation. This approach can help extend the lifespan of existing technology and provide climate change adaptation and resilience for coastal and riverine communities. The following paper will review seaweed farms as an advanced nature-based mitigation approach. The paper also outlines the findings of experiments at RWTH Aachen University's hydraulic laboratory. These tests involved using seaweed as a natural solution to dampen waves in a model system to test a hypothesis. One result involving a system with two lines of seaweed revealed 15 percent wave damping. Using seaweed as a nature-based solution, a gentle engineering approach to designing future vegetated protection systems can extend the design life of existing coastal infrastructure. This can also provide protection against climate-induced sea level rise, promote coastal risk mitigation, restore ecosystems, and foster blue bio-economic development.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

This study aims at investigating the catalytic performance of Pd, Pd/Pt, and Pd/Au nanocatalysts toward the 2-propanol electro-oxidation reaction (2POR) in an alkaline medium. The catalyst components (Pd, Pt, and Au) were sequentially electrodeposited onto a glassy carbon (GC) electrode surface and further characterized using electrochemical (cyclic voltammetry (CV)) and materials (Field-emission scanning electron microscopy (FE-SEM) coupled with energy dispersive X-ray (EDX)) characterization methods. The Pd/Au/GC catalyst showed the highest catalytic activity in terms of the highest oxidation current (0.386 mA) and the highest stability in terms of the highest obtained current after 1800 s of continuous electrolysis. This behaviour was attributed to the enhancement in the charge transfer kinetics where the Pd/Au/GC catalysts acquired the lowest charge transfer resistance (Rct, 1.85 kΩ) during the 2POR.

Background/Objectives: Airway management techniques, including mask ventilation and tracheal intubation, are vital across medical settings. However, these procedures can be challenging, especially when environmental conditions are less than ideal. This study explores how the height of the operating table affects the difficulty of surgical procedures involving mask ventilation and tracheal intubation. Methods: Twenty anesthesiologists participated in this study. We assessed the difficulty of procedures- such as mask ventilation, Macintosh laryngoscopy, and video laryngoscopy with McGRATH and AWS- on a four-level scale. The operating table’s height was adjusted at four points: operator's umbilicus, inferior margin of the 12th rib, xiphoid process, and nipple. Results: Mask ventilation was easiest at the operating table’s height aligned with the inferior margin of the 12th rib. Conversely, direct laryngoscopic exposure was perceived easier at higher table heights, with nipple height being optimal. McGRATH laryngoscopy showed consistent difficulty across table height, whereas AWS tended to be somewhat more difficult at greater heights. Conclusions: The optimal bed height for video laryngoscopy coincided with that for mask ventilation. Video laryngoscopy offers enhanced flexibility in optimal patient positioning compared to Macintosh laryngoscopy, contributing to its advantages in tracheal intubation procedures.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

This work involves results of research on short-term and long-term DC-drifts in electro-optical modulators based on annealed proton exchange waveguides in LiNbO3 crystals after wafer pre-annealing. The relaxation time of the DC-drift of the operating point for a short-term drift is minutes, and for a long-term drift, hours and days. DC-drift was measured by applying bias voltage and changing crystal temperature. Obtained results shows significant impact on stability of operating point in EO-modulators after treatment of defective structure of the near-surface layer of a LiNbO3 crystal. Treatment of the disturbed near-surface layer of a LiNbO3 crystal results in twice reduction of short-term DC-drift and increase of operation stability of electro-optical modulators during long-term measurement of temperature by activation energy calculation.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

This study examines the degradation of agglomerate particles in treated produced water used for hydraulic fracturing in the Bakken Formation. By analyzing d90 values and pump speeds from different manufacturers, the research quantifies particle size reduction rates, revealing how degradation contributes to pore throat blocking in tight formations. The study found that agglomerate particles in hydraulic fracturing fluids ranged from 9 to 85 microns in size, with degradation occurring most rapidly within the first five minutes of pump action. As time progresses, degradation slows, indicating that pore clogging is most likely at the beginning of the fracturing process. The research emphasizes that pump speed is a critical factor in determining the rate of particle degradation. To minimize formation damage, it is recommended to scale up particle size and use coarser particles in suspension. However, both large and small particles pose risks: larger particles can reduce porosity, while smaller particles may penetrate pore throats and form internal filter cakes. The study highlights the importance of selecting the appropriate pump speed and particle size distribution to optimize fracturing fluid design, maintain formation permeability, and reduce the risk of formation damage. Lower pump speeds and fewer coarse particles are advised to avoid pore clogging during the fracturing process.

This study reviews methods for detecting fracture closure pressure in both unconventional and conventional reservoirs using mathematical models and fluid flow equations. It evaluates tech-niques such as the Nolte method, tangent method, and compliance method. The investigation re-lies on observing changes in fluid flow regimes from pre-closure to post-closure, using fluid flow equations to examine the post-closure flow regime effect on the G function. Reverse calculations model pressure decline across synthesized flow regimes, facilitating a detailed investigation of the closure process. The analysis reveals that the tangent method is sensitive to post-closure fluid flow, while the compliance method is less effective in reservoirs with significant tortuosity or natural fractures. The paper recommends assessing natural fractures' characteristics and perme-ability to identify the source of leak-off before selecting a technique. It proposes integrating vari-ous methods for a comprehensive understanding of subsurface formations, combining their strengths for accurate fracture closure identification and better understanding of subsurface formations. The new proposed workflow employs the Continuous Wavelet Transform (CWT) technique for fracture closure detection, avoiding physical model pre-assumptions or simplifica-tions to confirm the results. This approach offers guidance on selecting appropriate methods by integrating different techniques.

Small submersible drainage pumps discharge leaking water and rainwater in buildings. In an emergency (e.g., heavy rain or accident), monitoring the flow rate in advance is necessary to enable optimal operation, considering the point where the pump operates abnormally when the water level increases rapidly. In another, pump performance optimization is crucial for energy saving policy. Therefore, it is necessary to meet the challenges of submersible pump systems, including sustainability and pump efficiency. The final goal of this study is to develop an energy-saving, high-efficiency submersible drainage pump capable of responding to emergencies. In particular, this paper targeted the hydraulic performance improvement of a submersible drainage pump model. Before the development of driving mode-related technology capable of emergency response, we first tried to find a way to improve the performance characteristics of the existing submersible drainage pump. Rather than designing a new pump, we disassembled the current pump and reverse engineering. Then, numerical simulation was performed to analyze the flow characteristics and efficiency of the pump. Then, the pump test was carried out to obtain the performance and validated with numerical results. Results revealed that changing the cross-sectional shape of the impeller reduced the flow separation and enhanced velocity and pressure distributions. Also, it reduced the power and increased efficiency. Results also showed that the pump's efficiency increased to 5.56% at a discharge rate of 0.17 m3/min, and overall average efficiency increased to 6.53%. In addition, the submersible pump design method could be suitable for the optimized pump's impeller and casing numerically. This paper can provide insight and information on the design optimization of pumps.

Critical infrastructures are those that are essential. For this type of infrastructure, it is necessary to implement analytical methodologies that will allow us to quickly obtain the susceptibility or resilience and possible damage generated in extreme precipitation episodes, through a holistic perspective in which the factors linked to hydrological risk intervene. In particular, urban hydraulic infrastructures are analyzed considering the degree of criticality, defined as the number of interactions on the different activities of the population. For this purpose, a hydrological risk analysis methodology is required. This methodology is focused on an integral approach of the system indicators to be analyzed and linked to the hydrological threat. This work proposes to delimit and analyze those factors that involve risk using an analytical expression. This model will estimate the damage to these infrastructures breaking down the factors involved in the risk equation and analyzing their variability according to the intrinsic characteristics linked to them as well as the interaction with external factors.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

In this study one of the most innovative sintering techniques up to date was evaluated: Electro-Sinter-Forging (ESF). Despite it has been proved to be effective in densifying several different metallic materials and composites, bearing steels such as 100Cr6 have never been processed so far. Pre-alloyed Astaloy CrM powders have been ad-mixed with either graphite or graphene and then processed by ESF to produce a 100Cr6 equivalent composition. Porosity has been evaluated by optical microscopy and compared to that one of 100Cr6 commercial samples. Mechanical properties such as hardness and transverse rupture strength were tested on samples produced by employing different process parameters and then submitted to different treatments (machining, heat treatment). The experimental characterization highlighted that porosity is the factor mostly affecting mechanical resistance of the samples, correlating linearly to the transverse rupture strength. Hardness on the other side does not correlate to the mechanical resistance because process related cracking has a higher effect on the final properties. Promising results were obtained that give room to the sinterability by ESF of materials difficult to sinter by conventional press and sinter techniques.

Microalgal harvesting is one of the most challenging processes in the development of algal research and development. Several methods, such as centrifugation, flocculation, and filtration, are available at the laboratory scale. However, the requirement of expensive pieces of equipment and the possibility of biomass contamination are recurring gaps that hinder the development of microalgae I+D in different parts of the world. Recently, the electroflotation has been proved as a suitable method for the harvesting of different species of microalgae and cyanobacteria. To this day, there are no companies that sell laboratory-scale electroflotation equipment; this is mainly due to the gap in the knowledge on which factors (time, mixing rate, number of electrodes, and others) will affect the efficiency of concentration without reducing the biomass quality. This paper aims to build an innovative low-cost electroflotation system under 300 USD with cheap and resistant materials. To achieve our goal, we test the interaction of three variables (time, mixing rate, and amount of electrodes) were evaluated. Results showed that an efficiency closer to 100% could be achieved under 20 minutes using >10 electrodes and 150 rpm. We hope this innovative approach can be used by different researchers to improve our knowledge of the concentration and harvesting of algae and cyanobacteria.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

Food composition data in the EMR countries are often lacking, obsolete or unreliable. The study aims to provide reliable and up-to-date nutrient data of selected food products consumed in Oman in order to evaluate consistency of nutrition labelling and update the current used food composition database. Contents of total fat, fatty acids, carbohydrates, total nitrogen, sugars and sodium were chemically analyzed in 221 foods and beverages purchased in 2022 and label and corresponding laboratory values were compared using the tolerance levels of the European Union. Food items were classified according their nutritional composition, the extent of processing and coded according FoodEx2 system. Results indicate that the nutrient values stated on a label align with the values obtained in the laboratory with the exception of a 6.3% discrepancy in TFAs content, where the reported values are higher than the appropriate reference values. The category with the highest frequency (71.5%) consisted of ultra-processed foods. In terms of inconsistencies in the nutrition claims, 5.1% of food products with claims did not comply with the statement “sugar free” or “low salt”. These findings underscore the significance of vigilant monitoring of nutritional labels as a means to implement measures that promote the well-being of consumers.

Currently, the design and construction of embankments of roads, railroads and hydraulic structures are based on regulatory documents developed 25-30 years ago. For the construction of granite massifs it is necessary to use sandy soils, the distribution of which in the Arctic zone of Siberia in the areas of construction is not more than 1.5%. In this case, the range of transport of sand in the alluvial area is 35 kilometers, in the rest of the area - an average of 60 kilometers. Large volumes of soil massifs require large amounts of transportation units, fuel consumption and are accompanied by large emissions of hydrocarbons into the atmosphere. Over the past 15 years, the authors have developed designs and technologies that significantly reduce the energy consumption during the construction of soil embankments. Combined structures are cages made of geosynthetic materials filled with unsuitable melted and frozen overmoistened clay and peaty soils. This allowed the use of soils within the construction sites and thereby reduce the range of transportation from 0.2 to 2.0 kilometers. As an example, when reducing the range of transportation from 25 km to 1 km, the energy consumption is reduced by a factor of 21. The use of geosynthetics made it possible to set the initial parameters of the water-heat regime control process, which increased the life cycle of the embankment from 2 to 5 times in comparison with traditional soil massifs and reduced the consumption of energy for repair and maintenance of linear transport structures. This article gives a theoretical substantiation of water-heat regime management, based on which new designs and technologies have been proposed and tested in Siberia in 2008-2013. The results of the tests confirm the theoretical research. Thus, the use of combined constructions of geosynthetics and inapplicable soils not only reduces the distance of transportation, but also reduces the volume of earthworks. It reduces the consumption of energy by 1.5-2 times.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

Electromagnetic (EM) waves, used for purposes such as geophysical characterization, impact properties to be measured. This paper describes the effects of radio frequency (RF) waves on the hydraulic conductivity of glass beads and natural sand. A series of tests were conducted using a customized, rigid-wall, cylindrical permeameter inside a resonant cavity made of Plexiglas covered with electrically conductive transparent films. Constant head ASTM-D2434 [1] tests were performed to measure the samples’ hydraulic conductivity. RF stimulation was performed using a magnetically coupled loop antenna at a constant frequency of 726 MHz and input power levels of 10, 25, 40, and 50 Watts. The hydraulic conductivity of both natural sand and glass-bead samples increased with RF stimulation. Furthermore, measurement of the electric-field component of RF waves was also performed to illustrate the pattern of the electric field as well as evaluate the RF impact on the hydraulic conductivity tests. The electric field was numerically simulated and validated against experimentally measured electric fields. A finite-difference numerical model was developed in MATLAB to analyze the seepage flow, which was then validated against the experimental results. An optimization scheme was then used to develop a governing equation for the RF impact on hydraulic conductivity.

A unified electro-gravity (UEG) theory, which has been successfully used for modeling an elementary particle, is applied in this paper to model gravitation in spiral galaxies. The new UEG model would explain the "flat rotation curves'' commonly observed in the spiral galaxies, without need for any hypothetical dark matter. The UEG theory is implemented in a somewhat different manner for a spiral galaxy, as compared to the simple application of the UEG theory to an elementary particle. This is because the spiral galaxy, unlike the elementary particle, is not spherically symmetric. The UEG constant $\gamma$, required in the new model to support the galaxies' flat rotation speeds, is estimated using measured data from a galaxy survey, as well as for a selected galaxy for illustration. The estimates are compared with the $\gamma$ derived from the UEG model of an elementary particle. The UEG model for the galaxy is shown to explain the empirical Tully-Fisher Relationship (TFR), is consistent with the Modified Newtonian Dynamics (MOND), and is also independently supported by measured trends of galaxy thickness with surface brightness and rotation speed. The UEG theory may similarly be extended to emulate the hypothetical dark matter in galaxy clusters as well as in cosmology.

In the fashion field, the use of electroplated small metal parts such as studs, clips and buckles is widespread. The plate is often made of precious metal, such as gold or platinum. Due to the high cost of these materials, it is strategically relevant and of primary importance for manufacturers to avoid any waste by depositing only the strictly necessary amount of material. To this aim, Companies need to be aware of the overall number of items to be electroplated so that it is possible to properly set the parameters driving the galvanic process. Accordingly, the present paper describes a Machine Vision-based method able to automatically count small metal parts arranged on a galvanic frame. The devised method relies on the definition of a proper acquisition system and on the development of image processing-based routines. Such a system is then implemented on a counting machine is meant to be adopted in the galvanic industrial practice to properly define a suitable set or working parameters (such as current, voltage and deposition time) for the electroplating machine and, thereby, to assure the desired plate thickness from one side and to avoid material waste on the other.

This paper provides a new management method (MM) to optimally operate standalone direct current (DC) photovoltaic water pumping system (PVWPS) and synchronize its hydraulic performance to variable daily irradiance. The proposed approach well considers the issues from PV generator and a positive displacement pump mismatching to deserve a hydraulic network. Accordingly, Management Method uses small pumps mounted in parallel scheme to displace the hydraulic power point (HPP) in order to satisfy the mal adequacy between supply and load. Based on experimental Study; this approach showed a yielded standalone system, possibility of running pumping system using only photovoltaic supply (Without use of capacitance), and possibility to design more economical PV systems as the maximum peak power demand for each month can be satisfied using small power pumps in parallel and adjusting their switch with accordance to varying daily irradiance. Moreover, an analytical model was developed with reference to the obtained experimental results. This model based on a daily occurring irradiance as inputs in order to predict optimal performance outputs. It can be considered as a decision tool to track power point resulting from optimal electrical and hydraulic performances of the pumping system according to changes of the daily irradiance.

In the paper is described the control electronics for an industrial pneumatic – hydraulic system based on a low-cost PLC. The developed system is a hydraulic pulse system and it generates series of high pressure hydraulic pulses (max. 200 bar). We describe requirements, an overall concept of the embedded control system, user interface, security features and network connectivity. In the description of the software solution we describe implementation of hierarchical ordered program threads (multithreaded program) and main control state machine. At the conclusion, we describe the calibration method of the system and calibration curves and we present the schematic diagram and a photo of a functional prototype of the system.

A fluid power industry powering the agricultural machinery faces big challenges nowadays. An issue of energy saving has become important due to increasing fuel costs and more stringent emissions regulations impacting vehicle development. A recent study conducted by the U.S. Department of Energy shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications and create innovative solutions. To increase energy efficiency of fluid power systems reduction of throttling losses and potential energy recovery strategies are needed. Aim of this work is to present classification of current energy saving architectures and aid the development of new techniques for mobile fluid power machines.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

Table detection is a preliminary step in extracting reliable information from tables in scanned document images. We present CasTabDetectoRS, a novel end-to-end trainable table detection framework that operates on Cascade Mask R-CNN, including Recursive Feature Pyramid network and Switchable Atrous Convolution in the existing backbone architecture. By utilizing a comparatively lightweight backbone of ResNet-50, this paper demonstrates that superior results are attainable without relying on pre and post-processing methods, heavier backbone networks (ResNet-101, ResNeXt-152), and memory-intensive deformable convolutions. We evaluate the proposed approach on five different publicly available table detection datasets. Our CasTabDetectoRS outperforms the previous state-of-the-art results on four datasets (ICDAR-19, TableBank, UNLV, and Marmot) and accomplishes comparable results on ICDAR-17 POD. Upon comparing with previous state-of-the-art results, we obtain a significant relative error reduction of 56.36%, 20%, 4.5%, and 3.5% on the datasets of ICDAR-19, TableBank, UNLV, and Marmot, respectively. Furthermore, this paper sets a new benchmark by performing exhaustive cross-datasets evaluations to exhibit the generalization capabilities of the proposed method.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

Perfluorooctanoic acid (PFOA), C7F15COOH, has been widely employed over the past fifty years, causing an environmental problem due to its dispersion and low biodegradability. Furthermore, the high stability of this molecule, conferred by the high strength of the C-F bond makes it very difficult to remove. In this work, electrochemical techniques are applied for PFOA degradation in view to study the influence of the cathode on defluorination. For this purpose, boron doped diamond (BDD), Pt, Zr and stainless steel have been tested as cathodes working with BDD anode at low electrolyte concentration (3.5 mM) to degrade PFOA at 100 mg/L. Among these cathodic materials, Pt improves the defluorination reaction. The electro-degradation of a PFOA molecule starts by a direct exchange of one electron at the anode and then follows a complex mechanism involving reaction with hydroxyl radicals and adsorbed hydrogen on the cathode. It is assumed that Pt acts as an electrocatalyst, enhancing PFOA defluorination by the reduction reaction of perfluorinated carbonyl intermediates on the cathode. The defluorinated intermediates are then more easily oxidized by HO• radicals. Hence, high mineralization (xTOC: 76.1%) and defluorination degrees (xF-: 58.6%) were reached with Pt working at current density j = 7.9 mA/cm2. This BDD-Pt system reaches a higher efficiency in terms of defluorination for a given electrical charge than previous works reported in literature. Influence of the electrolyte composition and initial pH are also explored.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

The newly developed friction-interlocking armor unit, called ‘Double cube’ (DC), has been designed to improve the performance of the concrete armor unit used in river/marine structures against currents/waves actions. DC unit, is an octagonal-shaped block, made up of two parts: an upper cube set on a lower base that is either square or octagonal in shape. The innovative design aims to provide a good performance in terms of stability, high tolerance placement with various contact points and ease of placement. DC’s shape and placement enhance the stability by bringing the center of gravity closer to the underlayer and providing a large contact surfaces with surrounding blocks that reduce the chance of extraction and limit movements (rocking, lifting) via "keystone" effect. The characteristics of this new unit provides a relatively high hydraulic stability number for the armor layer (NS=2.9), a favorable hydraulic performance due to energy dissipation from turbulence and aeration, as well as a high roughness coefficient (γf≈0.46) helping to reduce the overtopping.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

In the present work, we evaluate the prediction capability of six Pedotransfer functions (PTFs), reported in the literature, for the saturated hydraulic conductivity estimations (Ks). We used a database with 900 measured samples obtained from the Irrigation District 023, in San Juan del Rio, Queretaro, Mexico. Additionally, six new PTFs were construct for Ks from clay percentage, bulk density and saturation water content data. The results show, for the evaluated models, that one model present an overestimation for Ks>0.5 cm h-1 values, three models have a underestimation for Ks>1.0 cm h-1 and two models have a good correlation (R2>0.98) but are necessary more than three parameters. Nevertheless, the last two models requires from three to four parameters in order to get the optimization. By other hand, the models proposed in this work have a similar correlation with a less number of parameters: the fit is seen to be much better than using the existing ones, achieving a correlation of R2 = 0.9822 with only one variable and a R2 = 0.9901 when we use two.

The operational measure (OM) of the Second-Generation Intact Stability Criteria (SGISC) is the initial step toward the design of a performance-based dynamic stability assessment of the ship by considering both the vessel’s operation, loading condition and weather parameters. The SGISC recommends the standard wave scatter table (WST) for the environmental data, an indefinite requirement for a simplified assessment pathway, which provides the probability of wave occurrence. The existing standard WST was developed based on the North Atlantic Ocean. This study aims to identify the discrepancy in the probability of wave occurrence in the IMO-recommended WST when compared with developed hindcast WST for smaller regions of the North Atlantic Ocean for the application of SGISC. The significant difference in the existing standard WST is identified when compared with hindcast data, especially across different seasons. A case study of OM on the C11 class post-Panamax container ship for excessive acceleration is provided to better represent the study. The identified limitation limits the use of standard WST in ship stability assessment. The study recommends using hindcast-based WST for SGISC applications that are region and season based. This recommendation is beneficial in improving the safety assessment by OM, given the data is reliable and available for the season and region-specific, and hence the accuracy of the ship stability can be improved while using for the SGISC OM assessment. Further, it makes the WST adhere to the actual framework of the SGISC, i.e., using existing environmental data for design assessment and improving the simplified stability analysis.

Over the past decade, the volume and quality of data in the oil and gas industry have exploded, breeding exciting opportunities to implement machine learning for better data- driven decisions. One critical example is hydraulic fracturing (HF), given our ever-growing reliance on HF to meet global hydrocarbon demand. This paper systematically explores the work of several researchers to apply ML techniques (including linear regression, neural networks, support vector machine, decision trees, and more) to HF-related operations, from production forecast to HF design. Furthermore, this study examines how optimization algorithms (including gradient-free, differential evolution, and surrogate-based optimizations) are incorporated with different ML techniques for selecting optimal HF parameters (like fracture number, proppant concentration, and more) during the planning process. The paper aims to provide a comprehensive overview without delving too deeply into technical intricacies to ensure accessibility for a broader audience. Additionally, it introduces innovative techniques currently being integrated into the industry and offers a clear understanding of the processes involved. Ultimately, the analysis concludes that machine learning is an accurate and cost-effective alternative for hydraulic fracturing optimization.

The aim of the studies was to test the hydraulic pressure losses along the length, local pressure losses, absolute and relative roughness values of the pipeline walls made of modern polymer material. The article presents the results of the experimental studies of hydraulic resistance of pipelines from modern polymer materials, the method of theoretical determination of resistance coefficients in the VALTEC ISO 21003 metal polymer pipeline, the classification and method of determining the values of local hydraulic resistance coefficients of T-Junctions are given, the dependence for determining the Darcy λ hydraulic friction coefficient associated with the value of the equivalent hydraulic roughness coefficient of the inner surface of pipes and the Reynolds number. The experimental data of the hydraulic coefficient of friction Darcy λ was compared with the known theoretical relationships of A.D. Altschul, Colbrooke for smooth pipes, Colbrooke and White, an alternative to the Colbrooke-White, Offengenden equation for low-shear pipes and pipes from polymer materials with Reynolds numbers Re>10^4. Dependence of hydraulic coefficient of friction on relative equivalent roughness of pipeline walls and Reynolds number, specific energy loss per one linear meter on total flow rate in system of hydraulically short pipeline is obtained. The empirical dependence of values of coefficients of local resistance ζ=f(Q2/Q3) from a ratio of the divided expenses of Q2/Q3 of the equal-pass T-Junction α=90 the pipeline to a branch up, on pass in the direct T-Junction and division of streams at various internal pipeline diameters of VALTEC.