Antioxidants are very beneficial for health because they protect the body from the effects of free radicals on various degenerative diseases caused by food contamination, air pollution, sunlight, etc. In general, methods for measuring the capacity of antioxidants generally use accurate meth-ods such as spectrophotometry and chromatography. Still, it takes time, sample preparation and must be done in a laboratory with particular expertise. Therefore, a new, more practical method needs to be developed for determining antioxidants, namely the electrochemical method. The electrochemical method is promising to develop because it has several advantages, including high sensitivity and fast response. The electrochemical method discussed in this article reviews sensors, biosensors, and nanosensors. This paper comprehensively analyzes contemporary developments in electrochemical biosensor techniques and antioxidant evaluation methodologies. The discussion centers on utilizing multiple biosensors. Electrochemical biosensors have been determined to be prevalent in analyzing food quality, assessing active factor functionality, and screening practical components. The present study outlines the difficulties linked with electrochemical bio-sensor technology and provides insights into the potential avenues for future research in this domain.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

Bismuth oxides are well-known electro-catalysts in fuel cells systems; they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of BiO₂ and MnO₂ as catalysts in the pharmaceutical analysis is analytical method for the determination of heavy metal antibacterial agents in Pharmaceutical Dosage form is developed. The method is based on the voltammetric determination of heavy metal using Bidified platinum electrode by Bismuth oxide. The two components are oxidized at the Bidified electrode surface with the development of current that is linearly proportional to their concentrations in the range of 7.04*10^-7- 1*10^-3 M heavy metal. The oxidation reaction of the two components is pH-dependent, in which the buffer used is Britton-Robinson at pH = 7.00 where maximum peak current and maximum peak separation is obtained. The regression factors obtained from the calibration curves are 0.9812. The method of analysis was validated, where the limit of detection (LOD) and the limit of quantitation (LOQ) were calculated to be 1.44*10^-4 M, 4.36*10^-4 M and 1.27*10^-4 M, 3.84*10^-4 M respectively, the percentage recovery of both components was also calculated to 77 % for heavy metal.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

Nitroxyl radical catalysts oxidize alcohols under an applied electric potential. It is possible to quantify the alcohol concentration from the resulting oxidation current. In this work, we evaluated the catalytic activity of nitroxyl radicals (or their corresponding hydroxylamines), including 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) as representative nitroxyl radicals, acetoamido-TEMPO, which shows higher oxidation potential than TEMPO owing to the acetoamido group, AZADO, Nor-AZADO, and NNO as less-hindered bicyclic nitroxyl radicals, and NHPI as an N,N-diacyl-type hydroxylamine, in acetonitrile solution. TEMPO, AZADO and NNO were also evaluated for their ability to oxidize alcohols in organic solvents, and their reactivity was compared with the electrochemical response. The most active NNO was used for electrochemical detection of cyclosporin A, a drug with a hydroxyl group.

Hydrogel-based wearable electrochemical biosensors (HWEBs) are emerging biomedical devices that have recently received immense interest. The exceptional properties of HWEBs include excellent biocompatibility with hydrophilic nature, high porosity, tailorable permeability, the capability of reliable and accurate detection of disease biomarkers, suitable device-human interface, facile adjustability, and stimuli-responsive to the nanofiller materials. Although the biomimetic three-dimensional hydrogels can immobilize bioreceptors, such as enzymes and aptamers, without any loss in their activities. However, most HWEBs suffer from low mechanical strength and electrical conductivity. Many studies have been performed on emerging electroactive nanofillers, including biomacromolecules, carbon-based materials, and inorganic and organic nanomaterials, to tackle these issues. Non-conductive hydrogels and even conductive hydrogels may be modified by nanofillers as well as redox species. All these modifications have led to the design and development of efficient nanocomposites as electrochemical biosensors. In this review, both conductive-based and non-conductive-based hydrogels derived from natural and synthetic polymers are systematically reviewed. The main synthesis methods and characterization techniques are addressed. The mechanical properties and electrochemical behavior of HWEBs are discussed in detail. Finally, the prospects and potential applications of HWEBs in biosensing, healthcare monitoring, and clinical diagnostics are highlighted.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

Digital medicine based on the integration of all medical data of a particular patient, has become a reality today, thanks to information technology. Traditional medical examinations can be supple-mented by assessment results of the oxidative-anti-oxidative (OAO) status of the body [1]. Elec-trochemical sensors are able to not only determine the integral indicators of the OAO system of the body, but also to depict details of the processes occurring in the system. The main obstacle to the widespread use of electrochemical sensors in medical diagnostics is the extremely small amount of the received information in comparison with tens of thousands of known human dis-eases. The problem can be eliminated only by rethinking the purpose of electrochemical measure-ment within the framework of thermodynamics of information processes and information theory. In the information paradigm of electrochemical analysis of biological fluids, a sample is considered as an electrochemical message created by a sensor. The purpose of electrochemical measurement is to obtain information in a volume sufficient to identify the sample composition within the range of possible concentrations of its components. The fundamentals of the thermodynamics of infor-mation processes are considered and conclusions that are of practical importance for the devel-opment of electrochemical sensors and analyzers are derived. It is shown that potentiostatic con-trol of the sensor is physically impacted by the electromechanical instability of the electrical double layer, which is the main source of sensor signal noise. Estimates are of a minimum amount of an-alytical signal information required for identification of a sample of a known composition, such as a biological fluid, are provided. Examples of highly informative analytical signals for flowing and stationary samples are presented. Problems related to the visualization of such signals are noted.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

The segmentation of abnormal regions is vital in smart manufacturing. However, the existing segmentation system for detecting sauce-packet leakage on intelligent sensors encounters an issue of imaging blurring caused by uneven illumination. This issue adversely affects segmentation performance, thereby impeding the rapid production of industrial assembly lines. To alleviate this issue, we propose the two-stage Illumination-aware Sauce-packet Leakage Segmentation (ISLS) method for intelligent sensors. The ISLS comprises two main stages: Illumination-aware region enhancement and leakage region segmentation. In the first stage, YOLO-Fastestv2 is employed to capture the Region of Interest (ROI), which reduces redundancy computations. Additionally, we propose an image enhancement to relieve the impact of uneven illumination, enhancing the texture details of ROI. In the second stage, we propose a novel feature extraction network. Specifically, we propose the Multi-scale Feature Fusion Module (MFFM) and the Sequential Self-Attention Mechanism (SSAM) to capture discriminative representations of leakage. The multi-level features are fused by MFFM with a small number of parameters, which capture leakage semantics at different scales. The SSAM realizes the enhancement of valid features and the suppression of invalid features by adaptive weighting of spatial and channel dimensions. Furthermore, we generated a self-built dataset of sauce-packets, including 606 images with various leakage areas. Comprehensive experiments demonstrate that our ISLS method shows better results than several state-of-the-art methods, with additional performance analyses deployed on intelligent sensors to affirm the effectiveness of our proposed method. Our code is available at https://github.com/LSJ5106/SauceDetect.

We propose a neural-network-based watermarking method that introduces the quantized activation function that approximates the quantization of JPEG compression. Many neural-network-based watermarking methods have been proposed. Conventional methods have acquired robustness against various attacks by introducing an attack simulation layer between the embedding network and the extraction network. The quantization process of JPEG compression was replaced by the noise addition process in the attack layer of the conventional methods. In this paper, we propose a quantized activation function that can simulate the JPEG quantization standard as it is in order to improve the robustness against the JPEG compression. Our quantized activation function consists of several hyperbolic tangent functions and is applied as an activation function for neural networks. Our network was introduced in the attack layer of ReDMark proposed by Ahmadi et al. to compare it with their method. That is, the embedding and extraction networks had the same structure. We compared the usual JPEG compressed images and the images applying the quantized activation function. The results showed that a network with quantized activation functions can approximate JPEG compression with high accuracy. We also compared the bit error rate (BER) of estimated watermarks generated by our network with those generated by ReDMark. We found that our network was able to produce estimated watermarks with lower BERs than those of ReDMark. Therefore, our network outperformed the conventional method with respect to image quality and BER.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

Immunoglobulin G (IgG), a type of antibody, represents approximately 75% of serum antibodies in humans, and is the most common type of antibody found in blood circulation Consequently, the development of simple, fast and reliable systems for IgG detection are of considerable interest which can be achieved using electrochemical sandwich-type immunosensors. In this study we have developed an immunosensor sub-strate using an inexpensive and very simple fabrication method based on ZnO nanorods obtained through the electrodeposition of ZnO. The ZnO nanorods were treated by electrodepositing a layer of reduced gra-phene oxide to ensure an easy immobilization of the antibodies. On this substrate, the sandwich configura-tion of the immunosensor was built through different incubation steps, that were all optimized. The im-munosensor is electrochemically active thanks to the presence of gold nanoparticles tagging the secondary antibody, therefore it has been used to measure the current density of the hydrogen development reaction which is indirectly linked to the concentration of H-IgG antigens. In this way the calibration curve was constructed obtaining a linear range of 1-100 ng / ml with a detection limit of few ng / mL and good sensi-tivity.

Positioning based on wireless signals such as mobile communication networks has become an important means to provide high-precision location services in environments where satellite signals are blocked. In complex environments such as indoor and underground, wireless signal propagation is obstructed and non-line-of-sight (NLOS) phenomena appears due to serious occlusion and reflection. The time delay caused by NLOS effects has little impact on communication system but can significantly increase positioning errors in positioning systems. Therefore, effective suppression of NLOS errors is crucial to improving 5G positioning accuracy. To address the insufficient feature extraction of existing NLOS error suppression methods, the neglect of residual NLOS measurement errors, and poor stability of position estimation results, this paper innovatively proposes a NLOS mitigation and location estimation method for 5G positioning terminals. Simulation and experimental test results demonstrate that the proposed method outperforms the comparative methods both theoretically and practically, achieving an average positioning accuracy of 1.85 meters in complex indoor NLOS environments. The method proposed in this paper provides a new strategy for NLOS error suppression in indoor 5G positioning, which can significantly contribute to high-precision location services based on commercial 5G networks.

One of the industries with the fastest rate of growth is healthcare, and this industry's enormous data requires extensive cloud storage. The cloud may offer some protection, but there is no assurance that data owners can rely on it for refuge and privacy amenities. Therefore, it is essential to offer security and privacy protection. Increased customer satisfaction with security and privacy preservation is crucial since healthcare big data and its sources are stored in the cloud and contain increasingly private and sensitive information. However, maintaining privacy and security in an untrusted green cloud environment is difficult, thus the data owner should have complete data control. A new work SecPri-BGMPOP(security and privacy of Boost graph Convolutional Network -Pinpointing-Optimization Performance) is suggested that can offer a solution that involves several different steps in order to handle the numerous problems relating to security and protecting privacy. Initially Boost Graph Convolutional Network Clustering (BGCNC) algorithm, which reduces computational complexity in terms of time and memory measurements, is first applied to the input dataset to begin the clustering process. Second, enlarge by employing a piece of the magnifying bit string to generate a safe key, pinpointing based encryption avoids amplify leakage even if a rival or attacker decrypts the key or asymmetric encryption. Finally, to determine the accuracy of the method, an optimal key was created using a meta-heuristic algorithmic framework called Hybrid fragment horde bland lobo Optimization (HFHBLO). Our proposed method currently kept in a cloud environment, allowing analytics users to utilize it without risking their privacy or security.

As the natural resources are getting exhausted, the concept of sustainable development of region has received increasing attentions, especially for resource-dependent cities. In this paper an innovative method that emergy analysis and IPAT (Human Impact Population Affluence Technology) model were combined in order to analyze the quantitative relationship of economic growth and energy consumption and further to evaluate its overall sustainability level. Taiyuan, a traditional, resource-dependent city in China, is selected as the case study region. The main results show that total emergy of Taiyuan increased from 9.023× 1023 sej in 2007 to 9.116× 1023sej in 2014, with 38% reduction on non-renewable emergy and 125% growth on imported emergy. Regional emergy money ratio (RMB) was reduced by 48% from 5.31× 1013sej/$ in 2007 to 2.74× 1013sej/$ in 2014, indicating that the increasing speed of consuming resources and energy was faster than the increase of GDP, and that Taiyuan’s money purchasing power declined. The lower emergy sustainability index (ESI) indicates that Taiyuan was explored and produced large quantities of mineral resources, which puts more stress on the environment as a consequence, and that this is not sustainable in the long run. The IPAT analysis demonstrates that Taiyuan sticks to the efforts of energy conservation and environmental protection, in order to promote regional sustainable development, it is necessary to take an integrated effort. Policy insights suggest that resourceful regions should improve include energy and resource efficiency, optimizing energy and resourceful structure.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

The Internet of Things (IoT) is a concept based on the integration of various devices and methods of communication to exchange information in order to contribute to the improvement of everyday life, business and environment. This paper focuses on the establishment of a modern Internet of Things platform to ensure secure collection, processing and storage of data, under unexpected events. This platform establishes reliable connectivity which enhance system uptime; the key to success when implementing an IoT strategy. For this purpose, we proposed a hybrid approach combining different connectivity technologies to ensure the availability and smooth operation of the system and the prevention of data loss in unforeseen cases.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

Selenium is one of the inorganic compounds in human and animal nutrition and is involved in the proper functioning of the body. As a micronutrient, it actively contributes to the regulation of various metabolic activities, i.e., thyroid hormone, and protection against oxidative stress and cancer. Selenium anion also plays an essential role in the mechanism of immunity to viral infec-tions. However, this element can also be hazardous, especially in high concentrations. The toxicity of selenium is strongly associated with its chemical form. Se exhibits a narrow concentration window from having a positive to exerting a toxic effect. The daily uptake for humans is in the range of 55-400 µg/day. In higher doses (of the order of 900-1000 µg/day), it negatively affects the human body and causes DNA damage through the formation of free radicals. Increased reactivity of Se anion can also disrupt the integrity and function of DNA-repairing proteins. As the permis-sible concentration of Se in drinking water is 10 µg/L, it is vital to develop sensitive and robust methods of Se detection in aqueous samples.

Safety and quality are key issues for the food industry. Consequently, there is a growing demand to preserve the food chain and products against substances toxic, harmful to human health such as contaminants, allergens, toxins, or pathogens. For this reason, it is mandatory to develop highly sensitive, reliable, rapid, and cost-effective sensing systems/devices such as electrochemical sensors/biosensors. Generally, conventional techniques are limited by long time of analyses, expensive and complex procedures, and they require skilled personnel. Therefore, the development of performant electrochemical biosensors can significantly support the screening of food chain and products. Here, we report some of the recent developments in this area and analyze the contributions produced by electrochemical biosensors in the food screening and the challenges to address.

The process of blood coagulation, wherein circulating blood transforms into a clot in response to internal or external injury, is a critical physiological mechanism. Monitoring this coagulation process is vital to ensure that blood clotting occurs neither too rapidly nor too slowly. Anticoagulants, a category of medications designed to prevent and treat blood clots, require meticulous monitoring to optimise dosage, enhance clinical outcomes, and minimise adverse effects. This review article delves into the various stages of blood coagulation, explores commonly used anticoagulants and their targets within the coagulation enzyme system, and emphasises the electrochemical methods employed in anticoagulant testing. Electrochemical sensors for anticoagulant monitoring are categorised into two types. The first type focuses on assays measuring thrombin activity via electrochemical techniques. The second type involves modified electrode surfaces that either directly measure the redox behaviour of anticoagulants or monitor the response of standard redox probes in the presence of these drugs. The review provides a comprehensive list of different electrode compositions and their detection and quantification limits. Additionally, it discusses the potential of employing a universal calibration plot to replace individual drug-specific calibrations. The insights presented are anticipated to significantly contribute to the sensor community's efforts in this field.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

The River Habitat Survey (RHS) is a method for assessing the conditions of a river channel and valley, taking into account hydromorphological factors, and assessing the degree of naturalness or the degree of anthropogenic alteration within the channel and valley based on physical and landscape data. The hypothesis tested in this study was that the quality of river habitats demonstrated using the RHS should translate into the composition of their fauna. We investigated aquatic bugs (Heteroptera Aquatica), which are a group with considerable dispersal abilities and, at the same time, composed of stenotopic species associated with a particular environment as well as of eurytopic elements inhabiting a wide range of environments (REF). The research was carried out in a small lowland river, the River Krąpiel (north-western Poland) at 6 sites with 43 sub-sites included. Our analyses suggest the RHS method can predict the composition and quality of the aquatic bug fauna inhabiting a given river. Indicators of river habitat quality (HQA and RHQ) will be associated with different habitat types depending on the geographic location and type of river, once indicating habitats associated with the mainstream river and mineral substrate (mountain and small lowland rivers) and at other times habitats covered by vegetation with relatively slow water flow (large and medium lowland rivers). Therefore, RHS may be a good method for estimating the water bug fauna, linking it to the size and character of the river.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Polyvinyl alcohol (PVA) is highly compatible polymer with biological environments. Specifically, it has been used as a trap for different types of microorganisms in Bio-MEMS, and its properties can be modified to act as an electrode for electrochemical analysis. This study presents a nano-composite developed with PVA, multiwall carbon nanotubes (CNTs) doped with nitrogen, which changes the electrical properties of the polymer and its viscosity to obtain nanofibers by electro-spinning. The proposed nanocomposite was characterized using Fourier transform-infrared and Raman spectroscopy techniques, confirming the presence of the CNTs immersed in the polymer. High-resolution transmission electron microscopy was used to obtain the micrographs that showed the characteristic interplanar distances of the multiwall CNT in the polymeric matrix with values of 3.63 Å. Finally, the CNx mats were exposed to various aqueous solutions in a po-tentiostat to demonstrate the effectiveness of the nanofibers for electrochemical analysis. The CNx-induced changes in the electrical properties of the polymer were identified using cyclic voltammograms, while the electrochemical analysis revealed supercapacitor behavior.

The electrochemical oscillation was first observed in the charging process of anolyte in VRFBs. The chronopotentiometry with current ramp results could be used to judge the appearance of electrochemical oscillation. The electrochemical oscillation could be explained in terms of the competition between the growth and the chemical dissolution of V2O5 film in the H2SO4 solution. It was possible to regular the extra power consumption resulted by the electrochemical oscillation. This work might provide new focus on the charging process of the VRFBs and guide for new methods on energy saving.

By using Modified simple equation method, we study the Cahn Allen equation which arises in many scientific applications such as mathematical biology, quantum mechanics and plasma physics. As a result, the existence of solitary wave solutions of the Cahn Allen equation is obtained. Exact explicit solutions interms of hyperbolic solutions of the associated Cahn Allen equation are characterized with some free parameters. Finally, the variety of structure and graphical representation make the dynamics of the equations visible and provides the mathematical foundation in mathematical biology, quantum mechanics and plasma physics.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Water networks are critical infrastructure components, ensuring the continuous supply of high-quality drinking water to consumers. To secure such water supply, regular maintenance, including the replacement of deteriorating pipelines, is essential. In this study, a methodology has been developed for determining optimal pipeline replacement solutions in water supply systems at water utilities with limited data availability. Hydraulic analysis has been conducted on the segment of 25 km of the water supply network using the free software EPANET. Applying water network optimization, eight pipeline replacement projects according to 13 pre-defined criteria have been identified and evaluated. The paper outlines the methods for evaluating the criteria, including defining specific quantitative limits. The Analytical Hierarchical Process (AHP) method was used in the paper to determine the weights of the criteria. The reason for applying this method refers to problems that involve a set of criteria with a mixed structure, including both quantitative and qualitative aspects. Also, the paper describes the steps of the multi-criteria optimization method VIKOR, used to select the optimal project. This paper, considered as case studie, describes a method, i.e. application of a new principles and an innovative way to solve a problem for developing countries.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Transportation is the primary consumer of oil, accounting for a significant portion of global energy consumption (34%) and CO2 emissions (40%). Electrifying road transportation is crucial to mitigate the effects of global warming. The abundant potential of renewable energy sources like solar and wind is hindered by their intermittent nature and incongruity with peak energy demands. This calls for the development of sophisticated energy storage solutions. Metal-air batteries (MABs), emerging as viable alternatives to lithium-ion batteries (LIBs), have attracted considerable attention due to their promising applications in the transportation sector. Despite substantial progress in MAB development over the past two decades, overcoming critical challenges such as electrolyte decomposition, carbon cathode degradation, anodic dendrite growth, and air impurities remains essential for their commercial viability. This mini-review provides a comprehensive overview of MAB fundamentals and the challenges associated with their development. The insights presented in this review serve to illuminate the current landscape and future prospects of MABs in the transportation sector.

A 9,10-phenanthrenequinone (PQ) was electrochemically polymerized on a graphite rod electrode using potential cycling. The electrode modified by poly-9,10-phenanthrenequinone (poly-PQ) was studied by means of cyclic voltammetry, electrochemical impedance spectroscopy, atomic force microscopy and scanning electron microscopy. The poly-PQ shows variations in growth pattern depending on the number of potential cycles for the initiation of polymerization. Formed poly-PQ layer demonstrates good electric conductivity, great electrochemical capacitance and unique oxidation/reduction properties, which are suitable for broad technological applications, including applicability in biosensors, supercapacitors, and in some other electrochemical systems.

The objective of the present paper is to get a better understanding of the electrochemical properties of organoclays, which were prepared via solid-state intercalation of three cationic surfactants, such as dodecyltrimethylammonium, tetradecyltrimethylammonium, and hexadecyltrimethylammonium, as bromide salts, at different loading levels into the interlayers of two natural smectite clays (AH and DI). The electrochemical properties of the prepared organoclays were investigated by cyclic voltammetry. The cyclic voltammetry response of the electrochemical probe, 〖Fe(CN)〗_6^(3-)/〖Fe(CN)〗_6^(4-), shows that the intensities of the anodic and cathodic peaks don’t increase when the working electrode is based on carbon paste modified with the raw clays (AH or DI), whereas the peaks intensities increase significantly when the working electrode consists of carbon paste modified with organoclays. This increase in the intensity of the current indicates an improvement in the surface conductivity of the carbon paste electrode when they are modified with organoclays. When the working Electrode is based on organoclays modified carbon paste, the potential differences (ΔEp) are ranged between 140 and 170 mV, which are lower than those of the unmodified carbon paste electrode (330 mV) and those modified with raw clays (520 mV). This indicates an easy electron transfer process on the surface of the organoclays modified carbon paste electrodes.

Epigenetic modifications are closely related to diseases and physiological health, mainly including DNA methylation, RNA methylation, histone acetylation, and non-coding RNA. Recently, a large amount of research has been conducted on the detection of epigenetic modifications. Electrochemical biosensors, with their low cost, high sensitivity, high compatibility, and simple operation, have been widely used in the detection of epigenetic biomarkers. This review discusses the detection of epigenetic biomarkers using different electrochemical sensing methods. Here we discuss various aspects, including free labels, signal labeling, signal amplification, nano-based electrodes, and the combined use of other methods. By summarizing the existing electrochemical detection methods for epigenetic modifications, this review also proposes the future development trends and challenges for electrochemical biosensors in this field.

Removal of hexavalent chromium had attracted much more attention as it was a hazardous contaminant. Electrochemical reduction technology was applied to removal chromium (VI) from wastewater. The mechanism and parameters affect the reduction process were investigated. The results showed that the reduction efficiency was significantly affected by the concentration of H2SO4, current density and reaction temperature. And the reduction efficiency was up to 86.45% at concentration of H2SO4 of 100g/L, reaction temperature of 70 ℃, current density at 50 A/m2, reaction time at 180 min and stirring rate of 500 rpm. The reduction process of chromium (VI) was followed pseudo-first-order equation, and the reduction rate could be expressed as Kobs = k [H2SO4]1• [j] 4•exp-4170/RT.

The presence of antibiotic residues in honey has recently become a growing public health concern due to the overuse of these products in beekeeping and their transfer to the food industry. The aim of this study was to develop and validate a simple, selective and sensitive method for the simultaneous identification and quantification of residues of twenty-two sulfonamides, trimethoprim and dapsone in honey using a rapid and reliable liquid chromatography–tandem mass spectrometry (LC–MS/MS) method. The developed method showed good linearity, specificity, precision (repeatability and intra-laboratory reproducibility) and recovery. The decision limit (CCalpha) ranged between 2.16-22.12 µg/kg for CCα, while the detection capability (CCbeta) was between 2.16- 2.67-27.36 µg/kg. The method proved to be rapid, reliable and effective for the determination of sulfonamides, trimethoprim and dapsone from honey samples. The average recoveries were estimated to be between 70 and 106%. The relative standard deviations (RSDs) were between 6-18%. In practice, the method is essential to check the honey sold on the market and ensure its safety before it reaches the consumer.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

A chronically stable electrode material with low impedance for recording neural activity and high charge-injection capacity for functional electro-stimulation is desirable for the fabrication of implantable microelectrode arrays that aims to restore impaired or lost neurological functions in humans. For this purpose, we have investigated the electrochemical properties of sputtered ruthenium oxide (RuOx) electrode coatings, deposited on planar microelectrode arrays, using an inorganic model of interstitial fluid (model-ISF) at 37o C as the electrolyte. Through a combination of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) modelling study we have established the contribution of faradaic reaction as the major charge-injection contributor within the safe neural stimulation potential window of 0.6 V vs Ag|AgCl. We have also established the reversibility of the charge-injection process for sputtered RuOx film by applying constant charge-per-phase current stimulations at different pulse widths and by comparing the magnitudes of leading and trailing access voltages during voltage transient measurements. Finally, the impedance of the sputtered RuOx film was found to be reasonably comparable in both its oxidized and reduced states, although electronic contribution from capacitive double-layer was found to be slightly higher for the completely oxidized film around 0.6 V than its reduced counterpart around -0.6V.

In recent years, the discharge of various emerging pollutants, chemicals and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, there are still many gaps despite the great progress in using EO to treat real wastewater. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and another important advanced oxidation technology, PEC, called photoelectrocatalysis (PEC), has shortly been discussed and reviewed. This article showed that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

New advances in creating effective and affordable copper-based catalysts for water splitting represent a promising strategy for driving sustainable energy technologies. However, ma- terials containing copper are susceptible to corrosion and agglomeration. In this study, we describe a synthesis route to produce olamine-functionalized CuO nanoparticles using the Hot Injection method. Nanoparticles were obtained and subsequently deposited on FTO substrates, undergoing thermal treatment at 500°C and 600°C in atmospheres containing O2 and N2, aiming to enhance the adhesion of the active material to the substrate and modify its oxidation state. Microstructural properties were analyzed using XRD, SEM, and TEM, while electrochemical properties were studied using CV, LSV, and EIS. Electrodes treated thermally in an N2 atmosphere at 600°C exhibited higher ESCA, indicating a greater area of active sites exposed to surface reactions and, therefore, superior catalytic activity in Hy- drogen Evolution Reaction (HER). These findings show an interesting strategy for avoiding rapid electron-hole recombination and, consequently, CuO corrosion. For Oxygen Evolution Reaction (OER), samples treated thermally in O2 atmosphere at 500°C and 600°C appear to be more effective.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

In this work a research on pulsed electrochemical micromachining of Stainless Steel is presented. A suitable equipment to study the process is described as well as a fitting procedure to machine and measure the variables involved. A tool of Tungsten with a tip of about 5 mm diameter sunk in an electrolyte of NaNO₃ is used for the process. The pulse on-time must be maintained in the order of ns to achieve a good current confinement, since the tool is active. Some experiments were made to assess the most important variables of the process, as current confinement, surface roughness, material removal rate and efficiency. It is observed that the current confinement get worse when the pulse on-time increases, as well as surface roughness. The material removal rate and the efficiency increase with the voltage amplitude and the pulse on-time. The voltage amplitude must be higher than 12 V so that the phenomenon of passivation disappears. There is a compromise in the choice of the variables, so a suitable combination of parameters is determined so that a good material removal rate with an acceptable result is achieved.

Determining halal product of fermented foods and bevearages becomes important for muslim consumers due to religious codification of halal. In order to help on site analysis, an alcohol biosensor was under development. The biosensor was constructed using bacteria producing alcohol oxidase (AOX). Bacteria from apple juice was isolated in advance to obtain pure bacteria. The bacteria was cultured in two solid media. Bacteria on the Acetobacter media had a resistance in a solution containing alcohol with a higher concentration. Acetobacter was cultured on solid and liquid media for measuring at various ethanol concentrations (0.01%-3%) with different absorbance value. Bacteria with absorbance value 0.500 had the highest oxidation current peak. Later, it was used as bioreceptor for measuring ethanol by cyclic voltammetry method. The linearity of measurement later was compared with spectrophotometric measurement. By using cyclic voltammetry the linearity had higher R² value than spectrophotometric method. However, it only had stability for two days, there fore it needs more improvement for lasting its lifetime. Basically, electrochemical method has potency for further being improved fur as an alternative method of ethanol on-site measurement.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

In this paper, we compile the fractional power series method and the Laplace transform to design a new algorithm for solving the fractional Volterra integro-differential equation. For that, we assume the Laplace power series (LPS) solution in terms of power q=1m,m∈Z+, where the fractional derivative of order α=qγ for which γ∈Z+. This assumption will help us to write the integral, the kernel, and the nonhomogeneous terms as a LPS with the same power. The recurrence relations for finding the series coefficients can be constructed using this form. To demonstrate the algorithm's accuracy, the residual error is defined and calculated for several values of the fractional derivative. Two strongly nonlinear examples are discussed to provide the efficiency of the algorithm. The algorithm gains powerful results for this kind of problem. Under Caputo meaning the obtained results are illustrated numerically, and graphically. Geometrically, the behavior of the solution declares that the changing of the fractional derivative parameter values' in their domain alters the style of the attained solution in a symmetrical meaning and fully coinciding to the ordinary derivative value'. From these simulations, the results report that the recommended novel algorithm is a straightforward, accurate, and superb tool to generate analytic-approximate solutions for Integral, and integro-differental equations of fractional order.

Two-dimensional MXene synthesized from MAX phase ceramic has the good electrical conductivity, promising to be used as electrodes. In this study, Nb4C3Tx MXene and low-entropy (Nb0.8Ti0.05V0.05Zr0.05Ta0.05)4C3Tx MXene were prepared by etching Nb4AlC3 and (Nb0.8Ti0.05V0.05Zr0.05Ta0.05)4AlC3 ceramics in the HF acid at 60 oC. By investigating the electrochemical properties of lithium batteries, it was found that the Nb4C3Tx and (Nb0.8Ti0.05V0.05Zr0.05Ta0.05)4C3Tx could provide the specific capacities of 163.7 mAh·g-1 and 130 mAh·g-1 after 50 cycles at a current density of 0.1 A·g-1, respectively, and maintain the coulombic efficiency close to 100%, good for the utilization of electrodes in the lithium batteries.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Among the electrochemical energy storage (EES) technologies, rechargeable batteries (RBs) and supercapacitors (SCs) are the two most desired candidates for powering a range of electrical and electronic devices. The RB operates on Faradaic processes, whereas the underlying mechanisms of the SC vary as non-Faradaic in the electrical double layer capacitors (EDLCs), Faradaic at the surface of the electrodes in the pseudo capacitors (PCs), and a combination of both non-Faradaic and Faradaic in the hybrid capacitors. The EDLCs offer high power density but low energy density. The hybrid capacitors take advantage of the Faradaic process without compromising their capacitive nature. Unlike batteries, supercapacitors provide high power density and numerous charge-discharge cycles; however, their energy density lags that of batteries. Here, we review recently published critically selected articles on supercapatteries, a generic term that refers to EES devices that can combine the merits of EDLCs and RBs. Also discussed are the properties, design strategies, and future perspectives of supercapatteries.

Electrochemical biosensors based on immobilized enzymes are among the most popular and commercially successful biosensors. Literature in this field suggests that modification of electrodes with nanomaterials is an excellent method for enzyme immobilization, which can greatly improve the stability and sensitivity of the sensor. However, the poor stability, weak reproducibility, and limited lifetime of the enzyme itself still limit the requirements for the development of enzyme electrochemical biosensors for food production process monitoring. Therefore, constructing sensing technologies based on enzyme electrochemical biosensors remains a great challenge. This article outlines the construction principles of four generations of enzyme electrochemical biosensors and discusses the applications of single-enzyme systems, multi-enzyme systems and nano-enzyme systems developed based on these principles. The article further describes methods to improve enzyme immobilisation by combining different types of nanomaterials such as metals and their oxides, graphene-related materials, metal-organic frameworks, carbon nanotubes and conducting polymers. In addition, the article highlights the challenges and future trends of enzyme electrochemical biosensors, providing theoretical support and future perspectives for further research and development of high-performance enzyme chemical biosensors.

Coagulant lectin from Moringa oleifera seeds (cMoL) was characterized by potentiometry and scanning electron microscopy (SEM) using MOF, Metal-Organic Frameworks of [Cu3(BTC)2.H2O)3]n, to immobilize cMoL and construct biosensors. Developed aluminum-air batteries degraded indigo carmine dye formulated similar to a textile effluent; biosensors investigated cMoL interaction with specific galactose and monitored residual dye. SEM revealed components of electrode assembly steps. Oxide reduction reactions of batteries generated Al(OH)3 promoting dye electrocoagulation. Cyclic voltammetry showed differentiated redox peaks related to dye residue quantification by cMoL. Electrochemical systems evaluated cMoL interaction with ligand and efficiently degraded dye; biosensors could be used for lectin characterization and monitoring dye residues in environmental textile effluents.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

(1) Background: Although diagnostic criteria for massive hemorrhage with organ dysfunction such as disseminated intravascular coagulation associated with delivery have been empirically established based on clinical findings, strict logic has yet to be used to establish numerical criteria. (2) Methods: A dataset of 107 deliveries with ≥2,000 g of blood loss, among 13,368 deliveries from nine national perinatal centers in Japan between 2020 and 2023 was obtained. Twenty-three patients had fibrinogen levels &lt;170 mg/dl, which is the initiation of coagulation system failure per our previous reports. Three of these patients had hematuria. We used six machine learning methods to identify the borderline criteria dividing the fibrinogen/fibrin/fibrinogen degradation product (FDP) planes, using 15 coagulation fibrinolytic factors. (3) Results: The boundaries of hematuria development on a two-dimensional plane of fibrinogen and FDP were obtained. If the FDP–fibrinogen/3–60 (mg/dl) value is positive, this indicates hematuria; otherwise, the case is non-hematuria, as demonstrated by the support vector machine method that seemed the most appropriate. (4) Conclusions: The borderline criterion dividing the fibrinogen/FDP plane for patients with hematuria that could be considered organ dysfunction in massive hemorrhage during delivery was obtained using artificial intelligence, and this method seemed to be useful.

Polymer electrolyte was used as a medium for testing the performance of microband electrodes under conditions of linear diffusion. Cyclic voltammetry and chronoamperometry experiments were performed in such viscous medium, where diffusion rates are much slower than in fluid solutions. Confirmation of the existence of such conditions from the log i vs. log v or log i vs. log t relationships in the current equation always yielded values lower than the expected value of 0.5. This could indicate impure linear diffusion profile, i. e. some contribution from radial diffusion (edge effect). However, performing these tests in monomeric solvents of similar viscosities, such as glycerol or propylene glycol, gave the desired value of 0.5. These results lead to the conclusion that current equations which are based on Fick’s laws may not be applicable for polymer electrolytes, where various obstruction to diffusion make it a more complicated process than in monomeric solvents.

The study of the human microbiome is a multidisciplinary area that affects from the field of technology to that of personalized medicine. The possibility of using microbiota biomarkers for the improvement in the diagnosis and monitoring of diseases (e.g. cancer), health conditions (e.g. obesity) or clinical parameters (e.g. ageing) has aroused great expectations, also in the scope of bio-electroanalytical chemistry. The well-known advantages of electrochemical transduction: high sensitivity, rapid response and possibility of miniaturization, together with the potential of new nanomaterials to improve both the design of electrode platforms and the performance of the resulting electrochemical biosensors make presumably a huge development in the next few years providing a better understanding of human microbiome entities. In this review article, the recent applications of electrochemical (bio)sensors for monitoring microbial metabolites and biomarkers of diseases related to different types of the human microbiome, with a special focus on the gastrointestinal microbiome, are reviewed. Examples of electrochemical devices applied to real samples are critically discussed as well as the challenges and prospects to be faced.

Our investigations show that electrochemical corrosion of copper is faster than electrochemical corrosion of aluminium at temperatures below 100oC. Literature data analysis shows that the Al atoms diffuse faster than the Cu atoms at temperatures higher than 475oC, Al rich intermetallic compounds (IMCs) are formed faster in the Cu-Al system, and the Kirkendall plane shifts toward Al side. Electrochemical corrosion occurs due to electric current and due to diffusion. An electronic devise working time, for example, depends on initial copper cover thickness on aluminium wire, connected to the electronic devise, temperature, and volume and dislocation pipe diffusion coefficients, so copper, iron, and aluminium electrochemical corrosion rates are investigated experimentally at room temperature and at temperature 100oC. Intrinsic diffusivities ratios of copper and aluminium at different temperatures and diffusion activation energies in the Cu-Al system are calculated by proposed here methods using literature experimental data. Dislocation pipe and volume diffusion activation energies of pure iron are calculated separately by earlier proposed method using literature experimental data. Aluminium dissolved into NaCl solution as the Al3+ ions at room temperature and at temperature 100oC, iron dissolved into NaCl solution as the Fe2+ (not Fe3+) ions at room temperature and at temperature 100oC, copper dissolved into NaCl solution as the Cu+ ions at room temperature and as the Cu+ and the Cu2+ ions at temperature 100oC. It is founded experimentally that copper corrosion is higher than aluminium corrosion, and ratio of electrochemical corrosion rates, kCu/kAl>1, decreases with temperature increasing, although iron electrochemical corrosion rate doesn’t depend on temperature below 100oC. It is obvious, because melting point of iron is more higher then melting point of copper or aluminium. It is calculated that copper electrochemical corrosion rate is approximately equal to aluminium electrochemical corrosion at temperature about 300oC, so copper can dissolve into NaCl solution mostly as the Cu2+ ions at temperature about 300oC. Ratio of intrinsic diffusivities, DCu/DAl <1, increases with temperature increasing, and intrinsic diffusivity of aluminium could be approximately equal to intrinsic diffusivity of copper at temperature about 460oC.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

Chitosan is a biopolymer derived from chitin. It is a non-toxic, biocompatible, bioactive, and biodegradable polymer. Due to its properties, chitosan has found applications in several and different fields such as agriculture, food industry, medicine, paper fabrication, textile industry, and water treatment. In addition to these properties, chitosan has a good film-forming ability which allows it to be widely used for the development of sensors and biosensors. This review is focused on the use of chitosan for the formulation of electrochemical chemosensors. It also aims to provide an overview of the advantages of using chitosan as an immobilization platform for biomolecules by highlighting its applications in electrochemical biosensors. Finally, applications of electro-chemical chitosan-based chemosensors and biosensors in food safety are illustrated

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

In this work we looked for a stable and accurate procedure to perform feature selection in datasets with a much higher number of predictors than individuals, as in Genome-Wide Association Studies. Due to the instability in feature selection when many potential predictors are measured, a variable selection procedure is proposed that combines several replications of shrinkage regression models. A weighted formulation is used to define the final predictors. The procedure is applied to investigate Single Nucleotide Polymorphisms (SNPs) predictors associated to Alzheimer’s disease in the Alzheimer’s disease Neuroimaging Initiative (ADNI) dataset. Two data scenarios are investigated: one considering only the set of SNPs and another with the covariates age, sex, educational level and APOE4 genotype. The SNP rs2075650 and the APOE4 genotype are given as risk factors for AD, which is in line with the literature, and other four new SNPs are pointed, opening new hypotheses for in vivo analyses. These experiments demonstrate the potential of the new method for stable feature selection.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

In this work, we describe the optimization of carbon-based electrodes employed in Bio-Electrochemical Systems (BES) by the deposition on commercial carbon paper electrodes of nanostructured layers of poly(3,4-ethylene-dioxy-thiophene) poly(styrene-sulfonate) (PEDOT:PSS) via Ultrasonic Spray Coating (USC). This innovative application of USC allowed us to demon-strate that uniform and controlled depositions of PEDOT:PSS can be successfully obtained on car-bon-based electrodes. We characterized the morphology and verified the spatial uniformity of depositions via scanning electron microscopy and Raman spectroscopy. Electrochemical charac-terizations on fabricated electrodes demonstrated a more than two-fold increase in electrochemi-cal active surface area with respect to bare carbon paper. A lab-scale experiments on BES was performed selecting Microbial Fuel Cells (MFCs) as the reference devices. Devices featuring USC-deposited PEDOT:PSS electrodes showed a three-fold higher Energy recovery with respect to con-trol cells, reaching a maximum value of (13 ± 2) J·m−3. Furthermore, the optimal PEDOT:PSS con-centration for the MFCs improvement is in line with the values reported in the literature for other deposition methods. In conclusion, this work demonstrates that USC is a promising technique for application in BES.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

Nowadays, the world's refractory gold ore production accounts for about 30% of the world's total gold, such gold concentrate leaching rate is low, seriously limiting the efficient use of gold resources. The alkaline preoxidation process can improve the leaching rate of this kind of gold deposit, and has a good development and application prospect. So, it is of great significance to study the oxidation and dissolution behavior of pyrite in alka-line environment. In this paper, the oxidation process of gold-bearing pyrite in alkaline electrolyte was studied by electrochemical techniques, and the oxidation products of pyrite electrode in alkaline solution were characterized by XPS，SEM and other analytical methods. The results show that the optimum pH for pyrite electrochemical oxidation dissolution is about 12, and oxidation potential of pyrite should be above 0.8 V. In that proces of alkaline oxidation dissolution of pyrite, part of S element enters the electrolyte in the form of Sx2-, S2O32-, SO32-and SO42-, and a small amount of S element is adsorbed on the surface of the electrode in the form of S0 and becomes a part of the passive layer. Fe element is adsorbed on the surface of electrode in the form of Fe(OH)2, Fe2O3 and Fe2(SO4)3, which becomes the main component of passivation layer. This study provides a theoretical basis and reference data for the chemical preoxidation treatment of sulfide ores.

We present a critical analysis of the mechanism of reversible hydrogen evolution reaction based on thermodynamics of hydrogen processes considering atomic and ionic species as intermediates. Clear distinction between molecular hydrogen evolution/oxidation (H$_2$ER and H$_2$OR) and atomic hydrogen evolution/oxidation (HER and HOR) reactions is made. It is suggested that the main reaction describing reversible H$_2$ER and H$_2$OR in acidic and basic solutions is: $\ce{H3O^+} + 2e^- \xrightleftharpoons{\mathrm{({H}_{2}^{+}})_{ad}} \ce{H2} + \ce{OH^-}$, which proceeds via the formation of hydrogen molecular ion as intermediate and its potential is $E^{0}$ = 0.414~V (at the standard Hydrogen electrode SHE scale). We analyse experimentally reported data with models which provide \emph{quantitative} match (R.J.Kriek et al., Electrochem. Sci. Adv. e2100041 (2021)). The experimentally observed slope of $\lg(Current)$ vs. $Potential$ equal to $\approx 30$~mV/dec corroborates the presented model of H$_2$ER/H$_2$ER based on \ce{H2$^+$} as intermediate.

Bio-devices are designed to allow biological matter to perform in vitro almost the same functions it performs in vivo. Therefore, they can benefit from the specificities of such materials and are expected to perform better than traditional devices. On the other hand, the integration of biological material with electronic/electrochemical instrumentation requires careful attention and can produce unconventional results. In this paper, we describe the impedance response of an electrochemical cell that converts sunlight into electrical power. It uses the photosynthetic system known as Reaction Center, which is the core of photosynthesis in several living beings. Under illumination, an abrupt transformation drives the cell electrical response from insulator to conductor and a photocurrent is observed. The impedance spectrum shows a peculiar shape which significantly modifies with the protein activation. It has been analyzed by means of a graphical/analytical/ numerical procedure. The modelling identifies an analogue electrical circuit, whose parameters give quantitative information about the underlying process. Finally, an appropriate normalization of data is proposed which validates data in dark and light and can be useful as a fast screening of measurements.

Current commercially available instruments for monitoring mitochondrial respiration are incapable of single cell measurements. Therefore, we developed a three-electrode, Clark-type biosensor suitable for mitochondrial respirometry in single oocytes and embryos. The biosensor was embedded in a PMMA (polymethyl methacrylate) micro-chamber to allow investigation of single oocytes/embryos immersed in up to 100 µL of respiration buffer. The micro-chamber was completely sealed to avoid oxygen exchange between the inside of the chamber and the atmosphere, while being maintained at a temperature of 38.5 ˚C to preserve cell viability. Using amperometry, the oxygen consumption of cells inside the micro-chamber was measured as a change in output current and converted to femto-mol (fmol) oxygen consumed per second based on calibrations with known buffer oxygen concentrations. The sensor measured basal cell respiration supported by endogenous substrates, respiration associated with proton leak induced by inhibition of the adenosine triphosphate (ATP) synthase (complex V) with oligomycin, and the maximal non-coupled respiratory capacity revealed by Carbonyl cyanide-4-(trifluoromethoxy)phenylhydrazone (FCCP) titration. Some potential applications of this oxygen sensor system include evaluating effects of metabolic therapies on oocyte bioenergetics, and monitoring mitochondrial function throughout oocyte maturation and blastocyst development to predict embryo viability to compliment assisted reproductive technologies

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

The use of hydrogen fuel cells as a mobile source of electricity might prove to be a keystone in future decarbonization of heavy duty road and marine transport. Due to complex interplay of various physicochemical processes in the fuel cells, further development of these devices will rely on concerted effort of researchers from various fields, e.g. chemistry, physics, electric and mechanical engineering. This results in knowledge gaps which are filled by the information, dispersed in wide range of literature, but rarely covered in a short and condensed form. To address this issue and with the aim of providing a concise and simple explanation of fuel cell operation, we propose a simple educational model of the most relevant processes in the fuel cell, aimed at proper description of causal relations. The derivation of model equations provides an intuitive understanding of electric potentials acting on protons on the microscopic level and relates this knowledge to the common terminology in fuel cell research community, such as catalyst electric overpotential and internal membrane resistance. The results of the model fit well with experimental data, indicating that a simple description, provided in the paper, is sufficient for intuitive understanding of fuel cell operation.

The elimination of superoxide radical anions (O2•−) by 5-amino-2-hydroxybenzoic acid (mesalazine, 5-ASA), 4-amino-2-hydroxybenzoic acid (4-ASA), and related compounds used for ulcerative colitis treatment was investigated using cyclic voltammetry and electron spin resonance (ESR) analyses aided by density functional theory (DFT) calculations. Quasi-reversible O2/O2•− redox was found to be modified by the compounds, suggesting that an acid-base reaction in which a hydroperoxyl radical (HO2•) is formed from O2•− occurs. However, the deprotonated 5-ASA anion can eliminate O2•− through proton-coupled electron transfer (PCET), forming a radical product. This electron transfer (ET) was confirmed by ESR analysis. The 4-aminophenol moiety in 5-ASA plays an important role in the PCET involving two proton transfers and one ET based on -conjugation. The electrochemical and DFT results indicated that O2•− elimination by 5-ASA proceeds efficiently viathrough the PCET mechanism after deprotonation of the 1-carboxyl group. Thus, 5-ASA may act as an anti-inflammatory agent in the alkali intestine through PCET-based O2•− elimination.

Reinforcement corrosion due to chloride attack is of major economic significance for reinforced concrete structures. Pozzolans are known to inhibit corrosion initiation mainly by reducing concrete permeability. However, there is evidence in the literature that changes in the chemical environment in the concrete due to the pozzolans may be creating improved corrosion resistance, by themselves. In this study, the composition of a pore solution of mature hydrated cement paste containing silica-fume at different ratios was analyzed. The electrochemical behavior of reinforcing steel was studied in simulated pore solutions with silicate concentrations ranging from 0 to 35.6 mM, which are within the concentration range found by pore solution extraction to be up to 49 mM. Polished reinforcing steel specimens were used for cyclic voltammetry in simulated pore solutions with chloride concentrations of 10-20%. Better corrosion protection was found with increasing silicate concentration up to 3.56 mM. This was indicated by lower corrosion currents both in the passive state and after anodic activation. Anodic activation of steel in a 35.6 mM silicate solution with 20% NaCl yielded a higher potential than the anterior potential.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.