Low-frequency peaks in the Raman spectra of amorphous poly (ether ketone) (PEEK) are investigated. An amorphous sample with zero crystallinity, as confirmed by WAXRD, was used in this study. In a previous study, two peaks were observed in the low-frequency Raman spectra of crystallized samples. One of the peaks at 135 cm-1, disappeared for the amorphous sample. Furthermore, the peak at 50 cm-1 was observed for the first time in the crystallized sample. The peak at 50 cm-1, similar to the peak at 135 cm-1, disappeared in the amorphous state, and its intensity increased with increasing crystallinity. The origins of the two peaks were both associated with the Ph-CO-Ph-type intermolecular vibrational modes in the simulation. It was suggested that the Ph-CO-Ph vibrational mode observed in the low-frequency region of PEEK was strongly in-fluenced by the intermolecular order.

.Functionalization of multi-walled carbon nanotubes (MWNTs) surface with sulfonated poly(ether ether ketone) SPEEK chains using hexane diamine (HAD) as the interlinking molecule was investigated. MWNTs were first oxidized by nitric acid to generate carboxyl groups on their surface. Grafting of SPEEK chains on the MWNTs surface was achieved using hexane diamine as a cross-linking molecule. The attachment took place after the reaction of amine groups with carboxyl groups of oxidized MWNTs and sulfonate groups of SPEEK as confirmed by infrared (FTIR) analysis. Scanning electron microscopy (SEM) showed that MWNTs were packed into a dense and compact structure. Transmission electron microscopy (TEM) showed that the nanotubes were wrapped by polymer chains and arranged in a bundle like structure. These observations reveal that some of MWNTs were interconnected by SPEEK chains.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

The European Union's recent decision to renew the authorization for the use of glyphosate until 15 December 2033 stimulates the scientific discussion all around the world regarding its toxicity or otherwise for humans. Glyphosate is a chemical used by millions of tons in the last 50 years worldwide to drying weeds in cultivated fields, greenhouses, roadsides. Concern has been raised in many quarters about the possible presence in the food chain and the consequent adverse effects on health: both aspects that argue in favor of toxicity and those that instead may indicate limited toxicity of glyphosate are here discussed. The great debate that has been generated requires further investigations and field measurements to understand its fate once dispersed in the environment and its concentration in the food chain. Hence the need for validated analytical methods that are available to analysts in the field. In the present review, methods for the analytical determination of glyphosate and its main metabolite, AMPA, are discussed, with a specific focus on chromatographic techniques applied to cereal products. The experimental procedures are explained in any detail, including cleanup, derivatization, and instrumental conditions to give the laboratories involved enough information to proceed with the implementation of this line of analysis. The prevalent chromatographic methods used are LC-MS/MS, GC-MS/SIM, and GC-MS/MS but sufficient indications are also given to those laboratories that wish to use the simpler HPLC-FLD, HPLC-UV, GC-NPD or GC-FPD techniques for screening purposes. Concentrations from literature measured in wheat, corn, barley, rye, oats, soybean, and cereal-based foods are reported together with the regulatory status in various parts of the world and the accumulation mechanism. As for the accumulation in cereals, available data show that glyphosate tends to accumulate more in wholemeal flours than in refined ones, that its concentration in the product strictly depends on the treatment period (the closer it is to the time of harvesting, the higher the concentration) and that in cold climates the herbicide tends to persist in the soil for a long time.

The fact that quantum gravity does not admit a co-variant vacuum state has far-reaching consequences for all physics. It points out that space could not be empty, and we return to the notion of an ether . Such a concept requires a preferred reference frame for, e.g., universe expansion and black holes. Here, we intend to discuss vacuum and quantum gravity from three essential viewpoints: universe expansion, black holes existence, and quantum decoherence.

The aim of this study is to compare different methods used for determination of the DS for sulfonated membranes before and after high dose irradiation. Commercial PEEK was homogenously sulfonated up to DS of 60-90% and the membranes were prepared using solvent casting method. Part of the samples were irradiated with 10 MeV electron beam up to 500 kGy dose to assess the ionising radiation induced effects. Both non-irradiated and irradiated membranes were characterized by Fourier Transformation infrared (FT-IR) spectrometry, thermogravimetric analysis (TGA), proton nuclear magnetic resonance (1H-NMR), electrochemical impedance analysis and for the first time for non-irradiated membranes by spectrophotometric analysis with Cr(III). Comparison of the above-mentioned methods for application for DS assessment was done. It was observed that irradiated membranes presented a higher value of DS. Appearance of different new signals in 1H-NMR and FT-IR spectra of irradiated membranes indicated the effects of radiation induced changes in the structure of SPEEK materials. It was determined that the novel method with Cr(III) is applicable for the determination of SPEEK DS under 80%.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

This review resumes published data on fungal diversity in and within monuments (e.g., religious and secular monuments, museums, and statues), covering a multidisciplinary investigation into the complex interactions between fungi and cultural heritage structures. Fungi represent remarkable adversaries to monuments, potentially compromising their structural integrity and aesthetic value. Based on a bibliographic search of manuscripts published, the knowledge of fungal communities colonizing monuments was comprehensively assessed. This work first describes the diverse fungal species implicated in the degradation of monument materials (e.g., stone, metal, and glass). It elucidates the factors governing fungal colonization and proliferation in and within these structures (e.g., environmental conditions, construction materials, and human interventions). Finally, the efficacy of preservation and restoration techniques to mitigate fungal threats and safeguard our cultural heritage is also discussed. This synthesis highlights the pivotal role of mycological research in heritage conservation, and a platform for future studies to address critical knowledge gaps is provided. Understanding fungal diversity in and within monuments is critical to preserving these invaluable cultural treasures, as it informs targeted conservation strategies and ensures their longevity in the face of fungal challenges.

Two reversible furan-maleimide resins, in which there are rigid -Ph-CH2-Ph- structure and flexible -(CH2)6- structures in bismaleimides, were synthesized from furfuryl glycidyl ethers (FGE), 4,4′-diaminodiphenyl ether (ODA), N,N'-4,4'-diphenylmethane-bismaleimide (DBMI) and N,N'-hexamethylene-bismaleimide (HBMI). The structures of the resins were confirmed by Fourier transform infrared analysis, and the thermoreversibility was evidenced by differential scanning calorimetry (DSC) analysis as well as sol-gel transformation process. Mechanical properties and recyclability of the resins were preliminarily evaluated by the flexural test. The results show the Diels-Alder (DA) reaction occurs at about 90°C and reversible DA reaction does at 130-140°C for the furan-maleimide resin. Thermally reversible furan-maleimide resins have high mechanical properties. The flexural strength of cured FGE-ODA-HBMI resin arrives at 141 MPa. The resins have a repair efficiency of over 75%. After being hot-pressed for three times, two resins display higher flexural strength than 80 MPa.

The paper considers the symmetries of a bit of information corresponding to one, two or three qubits of quantum information and identifiable as the three basic symmetries of the Standard model, U(1), SU(2), and SU(3) accordingly. They refer to “empty qubits” (or the free variable of quantum information), i.e. those in which no point is chosen (recorded). The choice of a certain point violates those symmetries. It can be represented furthermore as the choice of a privileged reference frame (e.g. that of the Big Bang), which can be described exhaustively by means of 16 numbers (4 for position, 4 for velocity, and 8 for acceleration) independently of time, but in space-time continuum, and still one, 17th number is necessary for the mass of rest of the observer in it. The same 17 numbers describing exhaustively a privileged reference frame thus granted to be “zero”, respectively a certain violation of all the three symmetries of the Standard model or the “record” in a qubit in general, can be represented as 17 elementary wave functions (or classes of wave functions) after the bijection of natural and transfinite natural (ordinal) numbers in Hilbert arithmetic and further identified as those corresponding to the 17 elementary of particles of the Standard model. Two generalizations of the relevant concepts of general relativity are introduced: (1) “discrete reference frame” to the class of all arbitrarily accelerated reference frame constituting a smooth manifold; (2) a still more general principle of relativity to the general principle of relativity, and meaning the conservation of quantum information as to all discrete reference frames as to the smooth manifold of all reference frames of general relativity. Then, the bijective transition from an accelerated reference frame to the 17 elementary wave functions of the Standard model can be interpreted by the still more general principle of relativity as the equivalent redescription of a privileged reference frame: smooth into a discrete one. The conservation of quantum information related to the generalization of the concept of reference frame can be interpreted as restoring the concept of the ether, an absolutely immovable medium and reference frame in Newtonian mechanics, to which the relative motion can be interpreted as an absolute one, or logically: the relations, as properties. The new ether is to consist of qubits (or quantum information). One can track the conceptual pathway of the “ether” from Newtonian mechanics via special relativity, via general relativity, via quantum mechanics to the theory of quantum information (or “quantum mechanics and information”). The identification of entanglement and gravity can be considered also as a ‘byproduct” implied by the transition from the smooth “ether of special and general relativity’ to the “flat” ether of quantum mechanics and information. The qubit ether is out of the “temporal screen” in general and is depicted on it as both matter and energy, both dark and visible.

Iloperidone (ILO) is a second-generation antipsychotic drug and a first-line treatment approved by USFDA in May 2009. Iloperidone belongs to Biopharmaceutical Classification Systems (BCS) class II; thus, it is poorly water-soluble, highly permeable, and has pH-dependent solubility. Cyclodextrins and their derivatives have a wide range of applications in different formulations due to their complexation ability, which improves the solubility, stability, safety, and bioavailability of a drug. We have tried the complexation of iloperidone with sulfobutyl ether-β-cyclodextrin (SEβCD) to improve its solubility and dissolution. Complexation was done by the kneading method. The characterization of the SEβCD complexes with Iloperidone was done by FTIR, differential scanning calorimetry (DSC), saturation solubility, etc. A multimedia dissolution of the complex was carried out and compared with the plain drug. A significant improvement in drug release was found from SEβCD complexes in all media when compared with the drug alone.

(1) Background: Although diagnostic criteria for massive hemorrhage with organ dysfunction such as disseminated intravascular coagulation associated with delivery have been empirically established based on clinical findings, strict logic has yet to be used to establish numerical criteria. (2) Methods: A dataset of 107 deliveries with ≥2,000 g of blood loss, among 13,368 deliveries from nine national perinatal centers in Japan between 2020 and 2023 was obtained. Twenty-three patients had fibrinogen levels &lt;170 mg/dl, which is the initiation of coagulation system failure per our previous reports. Three of these patients had hematuria. We used six machine learning methods to identify the borderline criteria dividing the fibrinogen/fibrin/fibrinogen degradation product (FDP) planes, using 15 coagulation fibrinolytic factors. (3) Results: The boundaries of hematuria development on a two-dimensional plane of fibrinogen and FDP were obtained. If the FDP–fibrinogen/3–60 (mg/dl) value is positive, this indicates hematuria; otherwise, the case is non-hematuria, as demonstrated by the support vector machine method that seemed the most appropriate. (4) Conclusions: The borderline criterion dividing the fibrinogen/FDP plane for patients with hematuria that could be considered organ dysfunction in massive hemorrhage during delivery was obtained using artificial intelligence, and this method seemed to be useful.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Pharmaceutically active compounds and organic pollutants are becoming a major environmental dispute possessing serious threat to the water bodies and terrestrial ecosystem. Microorganisms are capable of the self-purification process, and hence the microbial degradation is considered a lucrative method to counteract the therapeutic and recalcitrant pollutants. Pharmaceutical toxicants in aquatic system can be treated by conventional wastewater treatment, but slow sludge settling, presence of mixture of pharmaceuticals and recalcitrant compounds often pose a potential ecological risk. Some microbial strains are very effective in reducing the chemical oxygen demand (COD), biological oxygen demand (BOD), total dissolved solids (TDS), and turbidity in pharmaceutical industrial wastewater treatment. The natural microbial community has a significant role in the ecological processes of pharmaceutical and organic compounds, including non-steroidal anti-inflammatory drugs, analgesics, blood lipid regulators and other micropollutants. Specific bacterial isolates can act as biodegraders, and fungal treatment could offer protection to the ecosystem. These microorganisms use the pollutants as their sole carbon source and transform the contaminants by co-metabolic pathways. Natural attenuation by native microorganisms, biostimulation and bioaugmentation are the processes employed to degrade the target contaminant. Microorganisms may also be genetically engineered to improve the neutralization efficiency, which would assist in the mineralization of the pollutants. Thus, employing microorganisms to detoxify the pollutants probably enhances the sustainable potential biodegradability, improves water quality standards and ensures eco-friendly alternative bioremediation strategy.

Modern concepts in irreversible thermodynamics are applied to system transformation and degradation analyses. Phenomenological entropy generation (PEG) theorem is combined with the Degradation-Entropy Generation (DEG) theorem for instantaneous multi-disciplinary, multi-scale, multi-component system characterization. A Transformation-Phenomenological Entropy Generation (TPEG) theorem and space materialize with system and process defining elements and dimensions. The near-100% accurate, consistent results and features in recent publications demonstrating and applying the new TPEG methods to frictional wear, grease aging, electrochemical power systems cycling—including lithium-ion battery thermal runaway—metal fatigue loading and pump flow, are collated herein, demonstrating the practicality of the new and universal PEG theorem, and the predictive power of models that combine and utilize the PEG and DEG theorems. The methodology is useful for design, analysis, prognostics, diagnostics, maintenance and optimization.

The transition towards a CO2 neutral industry is currently spurring many new developments regarding processes for the conversion of CO2, or CO2-rich streams, into platform molecules such as methanol and dimethyl ether (DME). New processes give rise to new separation challenges, as well as novel opportunities for joint optimization of reaction and separation. In this context, the separation of CO2 and DME can be performed very efficiently using the newly developed concept of Stripping Enhanced Distillation (SED). SED is a distillation process that utilizes an additional stripping component (clearing gas) to promote the separation in the column. SED benefits from the utilization of the feedstock components as a clearing gas that can afterwards be recycled back to the conversion unit with the vapor distillate. Strongly improving the separation performance in the column, this approach also removes the need for external stripping mediums and in addition this recycle approach may significantly reduce the demand on the conversion unit upstream of SED. The benefits of using SED are demonstrated for two different processes for DME synthesis: (i) CO2 – DME separation after the Sorption Enhanced DME Synthesis (SEDMES) process, using hydrogen as clearing gas, and (ii) CO2 – DME separation after direct DME synthesis via dry reforming (DIDR), using methane as clearing gas. For the different cases, it is shown that, with minimal adaptations, the energy consumption for distillation is reduced by 20-30%, while product losses are minimized at the same time.

Inflammation mediators enhance the activity of connexin (Cx) hemichannels especially in the epithelial and endothelial tissues. As potential release route for injury signals like (oligo)nucleotides, Cx hemichannels may contribute to long lasting inflammation. Specific inhibition of Cx hemichannels may therefore be a mode of prevention and treatment of long lasting, chronic sterile inflammation. The activity of Cx hemichannels was analysed in N2A and HeLa cells transfected with human Cx26 and Cx46 as well as in Calu-3 cells using the dye uptake as functional assay. Moreover, possible impact of the bioactive phenolic agents CVB2-61 and CVB4-57 on the barrier function of epithelial cells was analysed using Calu-3 cells. Both agents inhibited the dye uptake in N2A cells expressing Cx26 (> 5 µM) and Cx46 (> 20 µM). In Calu-3 cells, CVB2-61 and CVB4-57 reversible inhibited the dye uptake at concentrations as low as 5 µM, without affecting the gap junction communication and barrier function, even at concentrations of 20 µM. While CVB2-61 or CVB4-57 maintained a reduced dye uptake in Calu-3 cells, an enhancement of the dye uptake in response to stimulation of adenosine signaling was still observed after removal of the agents. The report shows that CVB2-61 and CVB4-57 reversible block Cx hemichannels. Deciphering the interaction mechanisms with Cx hemichannels could allow further development of phenolic compounds to target Cx hemichannels for a better and safer use in treatment of pathologies that involve Cx hemichannels.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

The objective of this study is to design an optimal model predictive control (MPC) strategy using manipulated variables to control the production of a sufficient amount of hydrogen through low temperature autothermal reforming of dimethyl ether (DME), a reforming reaction performed using PdO/ZnO/γ-Al2O3 catalysts coated on honeycomb cordierite ceramics. Experiments and simulation have verified that the optimal activity temperature of the catalyst is 400 °C, and the hydrogen volume fraction in syngas is over 43%. In the implementation of the hydrogen production system, the MPC controller can precisely determine the feed rates of DME, high-purity air, and water based on the space state equation of the reformer, to achieve the anti-disturbance of the reformer temperature. Thus, the reduction of hydrogen yield and sintering of the catalyst as a result of overheating are prevented. As the static and dynamic performance of hydrogen production exhibits excellent tracking of the setpoints, an autonomous, automated, and reliable continuous system was designed to meet the desired hydrogen demand situation. This study shows that an autonomous, automated, and reliable continuous hydrogen production reforming system can be designed to actively respond to the on-board hydrogen usage situation.

With the global increase of photovoltaic (PV) modules deployment in recent years, the need to explore and realize their reported failure mechanisms has become crucial. Despite PV modules being considered reliable devices, failures and extreme degradations often occur. Some degradations and failures can be minor and cause no critical harm if within the expected range. Others, may start mildly and then deteriorate faster to become catastrophic, especially in harsh environments. This paper conducts a state-of-the-art literature review to scan PV failures, types, and their root cause based on PV’s constructed components (from protective glass to junction-box). It outlines the hazardous consequences beyond PV module failures, describing what harm they can bring to the PV system. As we delve into the literature, it becomes clear that every component is vulnerable to certain types of failures; some can deteriorate within themselves, and others infect further PV components resulting in emerging more severe failures. In the end, the review briefly summarises PV failure detection techniques, emphasising electrical characterization techniques, and disclosing the need to engage more electrical parameters. Most importantly, this review can prepare the stage for the PV research community to identify the most prevalent degradation processes. This, in turn, encourages researchers to investigate them throughout modelling and experimental studies to forecast them at the early onset in order to protect the PV systems from hazardous malfunctions.

In this research, a screw-barrel system was designed and implemented, coupled with material extrusion, to print high-melt-temperature thermoplastic materials. The aim was to integrate two methods: the direct extrusion of thermoplastic polymer pellets with material extrusion,utilize various polymers in the form of pellets, especially high melt temperature ones, instead of traditional filaments. This addresses one of the significant challenges in filament preparation for various materials that are not readily available in the market or nearly impossible to fabricate (such as highly filled plastics). First, the screw-barrel assembly performance and factors influencing feed rate were evaluated. Subsequently, specimens were printed with polyether ether ketone (PEEK), an advanced plastic material known for its outstanding mechanical properties, high-temperature tolerance, and broad applications in various sectors, such as medical. Additionally, the material was reinforced with 2.5% continuous glass fibers while printing, which presented a novel product. Upon comparing theoretical values with experimental data from the tensile testing, a notable observation emerged: the inclusion of 2.5% glass fibers led to an approximate 43% increase in the tensile strength of the material. Furthermore, SEM images provided visual evidence of satisfactory adhesion between layers and fibers.

Permeability has an important effect on drug absorption. In this study, the effect of different concentrations of sodium sulfobutyl ether-β-cyclodextrin (SBE-β-CD) on the absorption of ranitidine was investigated to examine the mechanism of permeability changes. The results of parallel artificial membrane permeability assay (PAMPA) showed that increasing the concentration of sodium sulfobutyl ether-β-cyclodextrin, 0, 0.12% (w/v), 0.36% (w/v) and 3.6% (w/v), respectively, the apparent permeability coefficient of ranitidine decreased to 4.62×10-5 , 4.5×10-5 , 3.61×10-5 and 1.08×10-5 in Caco-2 cells, respectively. The same results were obtained from oral pharmacokinetic study in rats; Further studies indicated that SBE-β-CD significantly increased the zeta potential of ranitidine. SBE-β-CD interacted with ranitidine charges to form a complex that reduced ranitidine permeability, and SBE-β-CD should be chosen with caution for drugs with poor permeability.

Electrical properties of the thin films of poly(arylene ether ketone) copolymers (co-PAEKs) with the fraction of phthalide-containing units of 3, 5 and 50 mol% in the main chain were investigated by using radiation induced conductivity (RIC) measurements. Transient current signals and current-voltage (I-V) characteristics were obtained under exposing 20÷25 thick films of the co-PAEKs to monoenergetic electron pulses of the energy ranged from 3 to 50 keV in the electric field ranged from 5 to 40 V/μm. The Rose-Fowler-Vaisberg semi-empirical model based on a multiple trapping formalism was used for an analysis of the RIC data and the parameters of the highly dispersive charge carrier transport were evaluated. The analysis revealed that charge carriers moved in isolation from each other and the applied electric fields were below the threshold field triggering the switching effect (a reversible high-to-low resistivity transition) in the co-PAEK films. It was also found that the co-PAEK films due to the super-linear I-V characteristics are highly resistant to electrostatic discharges arising from the effects of ionizing radiation. This property is important for the development of protective coatings for electronic devices.

A specific HPLC method has been developed and validated for the determination of vanillyl butyl ether in cosmetic products. The extraction procedure with an isopropanol water 1:1 mixture is described. The method uses a RP-C-18 column with isocratic elution and a UV detector. The mobile phase consists of a mixture of acetonitrile and buffer (Na2HPO4 20mM in water) (30:70 v/v) with a variable flow rate. The method was validated with respect to accuracy, precision (repeatability and reproducibility), specificity and linearity. The procedure described here is simple, selective and reliable for routine quality control analysis and stability tests of commercially available cosmetic products.

Chronic kidney diseases (CKD) and end stage renal disease (ESRD) are growing threats worldwide. Tissue engineering is a new hope to surpass the current limitations such as the shortage of donor. To do so, the first step would be fabrication of an intact decellularized kidney scaffold. In the current study, an automatic decellularization device was developed to perfuse and decellularize male rats' kidneys using both sodium lauryl ether sulfate (SLES) and sodium dodecyl sulfate (SDS) and to compare their efficacy in kidney decellularization and post-transplantation angiogenesis. After anesthesia, kidneys were perfused with either 1% SDS solution for 4 h or 1% SLES solution for 6 h. The decellularized scaffolds were stained with hematoxylin and eosin (H&E), periodic acid Schiff (PAS), Masson’s trichrome, and alcian blue to determine cell removal and glycogen, collagen and glycosaminoglycans (GAGs) contents, respectively. Moreover, scanning electron microscopy (SEM) was performed to evaluate the cell removal and preservation of microarchitecture of both SDS and SLES scaffolds. Additionally, DNA quantification assay was applied for all groups in order to measure residual DNA in the scaffolds and normal kidney. In order to demonstrate biocompatibility and bioactivity of the decellularized scaffolds, allotransplantation was performed in back muscle and angiogenesis was evaluated. Complete cell removal in both SLES and SDS groups was observed in SEM and DNA quantification assays. Moreover, the extracellular matrix (ECM) architecture of rat kidney in the SLES group was significantly preservation better than the SDS group was shown. The formation of blood capillaries and vessels were observed in the kidney allotransplantations in both SLES and SDS decellularized kidneys. In conclusion, we demonstrated that both SLES and SDS could be promising tools in kidney tissue engineering. The better preservation of ECM than SDS, introduces SLES as the solvent of choice for kidney decellularization. ¬¬

Mirrors are a subset of optical components essential for the success of current and future space missions. Most of the telescopes for space programs ranging from Earth Observation to Astrophysics and covering the whole electromagnetic spectrum from X-rays to Far-Infrared are based on reflective optics. Mirrors operate in diverse and harsh environments that range from Low-Earth Orbit, to interplanetary orbits and the deep space. The operational life of space observatories spans from minutes (sounding rockets) to decades (large observatories), and the performance of the mirrors within the mission lifetime is susceptible to degrade, which results in a drop of the instrument throughput, which in turn affects the scientific return. Therefore, the knowledge of potential degradation mechanisms, how they affect mirror performance, and how to prevent them is of paramount importance to ensure the long-term success of space telescopes. In this review we report an overview on current mirror technology for space missions with a focus on the importance of degradation and radiation resistance of the coating materials. A special attention will be given to degradation effects on mirrors for the far and extreme UV as in these ranges the degradation is enhanced by the strong absorption of most contaminants.

Resistance to the existing drugs and increasing numbers of diseases result in identifying new drug candidates with new forms of activity. Marine sources of alkylglycerols such as the liver oil Shark (SLO) mixture of certain species or rat fish (elasmobranch fishes) contain high levels of these compounds as a mixture of few species varying by length and unsaturation or saturation of the alkyl chain. They have multiple biological activities such as hematopoiesis stimulation, lowering radiotherapy-induced injuries, reducing tumor growth and improving vaccination efficiency. The synthesis of two Alkylglycerols (AKGs) containing at least one alkyne moiety in the alkyl chain has been reported. In this work, we describe the synthesis of others unknown AKGs based alkyne 1-O-(hexadec-11’-ynyl)-sn-glycerol 4 and 1-O-(octadec-9’-ynyl)-sn-glycerol 5 as analogues of bioactive ether lipids found in the SLO mixture.

The present review explores the critical role of oxime and oxime ether moieties in enhancing the physicochemical and anticancer properties of structurally diverse molecular frameworks. Specific examples are carefully selected to illustrate the distinct contributions of these functional groups to general strategies for molecular design, modulation of biological activities, computational modeling, and structure-activity relationship studies. An extensive literature search was conducted across three databases, including Pub-Med, Google Scholar, and Scifinder, enabling us to create one of the most comprehensive overviews of how oximes and oxime ethers impact antitumor activities within a wide range of structural frameworks. This search focused on various combinations of keywords or their synonyms, related to the anticancer activity of oximes and oxime ethers, structure-activity relationships, mechanism of action, as well as molecular dynamics and docking studies. Each article was evaluated based on its scientific merit and the depth of the study, resulting in 268 cited references and more than 336 illustrative chemical structures carefully selected to support this analysis. As many previous reviews focus on one subclass of this extensive family of compounds, this report represents one of the rare and fully comprehensive assessments of the anti-cancer potential of this group of molecules across diverse molecular scaffolds.

Zinc nanoparticles (ZnNPs) open new opportunities for biomedical applications as a strategy against microbes and dye removal in an efficient way. The composite ZnNPs using Rhododendron arboreum (R. arboreum) stem bark were synthesized and characterized for UV-visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The synthesized nanoparticles showed zones of inhibition of 23±0.09, 18±0.1 and 16±0.05 mm, against the Klebsiella pneumoniae (K. pneumoniae), Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli strains. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) values against K. pneumoniae, S. aureus, and E. coli were found to be 34±0.21 and 72.71±0.47, 47±0.11 and 94.86±0.84 and 94±0.18 and 185.43±0.16 µg/mL, respectively. The biosynthesized ZnNPs resulted in significant eradication of the outer and inner membranes of the bacterial cells. Likewise, the synthesized ZnNPs showed time-dependent photocatalytic degradation activity and revealed 65% methyl orange dye degradation with an irradiation period of 6 hours. The findings of this study suggest the suitability of the novel R. arboreum stem bark-based ZnNPs as an effective ameliorant against bactericidal activities and photocatalysts for the removal of hazardous water contaminants.

This study presents a preliminary analysis of the chemical and thermal fuel properties of Afuze (AFZ) coal extracted from coalfields in Owan East Local Government Area of Edo State, Nigeria. The chemical properties of AFZ were examined by combined scanning electron microscopy-energy dispersive X-ray (EDX), whereas the thermal properties were deduced by thermogravimetric analysis (TGA) under flash (50 °C/min heating rate) oxidative (combustion) and non-oxidative (pyrolysis) conditions. The microstructure and morphology analysis of AFZ revealed has a compact structure comprising small-to-large, irregular shaped and exfoliated grains with a vitreous appearance typically ascribed to metal elements (Ti and Fe) kaolinite, quartz, and other clay minerals. Chemical analysis revealed carbon, oxygen, aluminium, silicon, sulphur, calcium, titanium, and iron in major and minor (trace) quantities. Thermal analysis under oxidative and non-oxidative conditions revealed degradation occurs in three stages, namely; drying or demineralisation, devolatilization or maceral degradation and the formation of char/coke or ash. Lastly, the findings showed that the temperature range for the oxidative thermal degradation process (338.58 - 756.76 °C) was higher than the non-oxidative process (378.43 - 615.34 °C). This observation can be explained by the exothermic nature of the oxidative (combustion) process, which ensures greater heat supply required to thermally soften or degrade the maceral coal components. Overall, the oxidative process yielded the residual mass (RM = 21.97%) and mass loss (ML = 78.03%). The lower ML (49.03%) but higher RM (50.97%) observed during non-oxidative degradation of AFZ could be ascribed to the largely endothermic nature of the process.

The photocatalytic degradation of two quinolone-type antibiotics (ciprofloxacin and levofloxacin) in aqueous solution was studied, using catalysts based on ZnO nanoparticles, which were synthesized by a thermal procedure. The efficiency of ZnO was subsequently optimized by incorporating different co-catalysts of gC3N4, reduced graphene oxide and nanoparticles of gold. The catalysts were fully characterized by electron microscopy (TEM and SEM), XPS, XRD, Raman, and BET surface area. The most efficient catalyst was 10%Au@ZnONPs-3%rGO-3%gC3N4, allowing to obtain degradations of both pollutants above 96%. This catalyst has the largest specific area, and its activity has been related to a synergistic effect, involving factors as relevant as the surface of the material and the ability to absorb radiation in the visible region, mainly produced by the incorporation of rGO and gC3N4 to the semiconductor. The use of different scavengers during the catalytic process, was used to establish the possible photodegradation mechanism of both antibiotics.

The asymmetric synthesis of polyunsaturated triene C18:3 n-3 and C18:3 n-6 methoxylated ether lipids (MEL) of the 1-O-alkyl-sn-glycerol type is described as possible structural candidates for a triene C18:3 MEL of an unknown identity found in a mixture of shark and dogfish liver oil. Their C18:3 hydrocarbon chains constitute an all-cis methylene skipped n-3 or n-6 triene framework, along with a methoxyl group at the 2'-position and R-configuration of the resulting stereogenic centre. The methoxylated polyenes are attached by an ether linkage to the pro-S hydroxymethyl group of the glycerol backbone. The syntheses were based on the polyacetylene approach that involves a semi-hydrogenation of the resulting triynes. Both syntheses were started from our previously described enantio- and diastereomerically pure isopropylidene-protected glyceryl glycidyl ether, a double-C3 building block that was designed as a head group synthon for synthesis of various types of MELs.

As a widely used plastic, the aging and degradation of polyethylene (PE) are inevitable problems, whether the goal is to prolong the life of PE products or address the issue of white pollution. Molecular simulation is a vital scientific tool in elucidating the mechanisms and processes of chemical reactions. To obtain the distribution and evolution process of PE's thermal oxidation products, this work employs the self-consistent charge density functional tight binding (SCC-DFTB) method to perform molecular simulations of the thermal oxidation of PE with different crystallinity and branched structures. We discovered that crystallinity does not affect the thermal oxidation mechanism of PE, but higher crystallinity makes PE more susceptible to cross-linking and carbon chain growth, reducing the degree of PE carbon chain breakage. The branched structure of PE results in differences in pore size between the carbon chains, with larger pores leading to a concentrated distribution of O2 and free radicals subsequently formed. The breakdown of PE is slowed down when free radicals are localized in low-density regions of the carbon chain. The specifics and mechanism of PE's thermal oxidation are clearly revealed in this paper, which is essential for understanding the process in-depth and for the development of anti-aging PE products.

Autophagy is a cellular mechanism that utilizes lysosomes to degrade its own components and is performed using Atg5 and other molecules originating from the endoplasmic reticulum membrane. On the other hand, we identified an alternative type of autophagy, namely, Golgi membrane-associated degradation (GOMED), which also utilizes lysosomes to degrade its own components, but does not use Atg5 originating from the Golgi membranes. The GOMED pathway involves Ulk1, Wipi3, Rab9 and other molecules, and plays crucial roles in a wide range of biological phenomena, such as the regulation of insulin secretion and neuronal maintenance. We here describe the overview of GOMED, the methods to detect autophagy and GOMED, and to distinguish GOMED from autophagy.

Bisphenol-A (BPA) represents an important co-monomer for obtaining polycarbonate, epoxy resins, flame retardants, in paint, and other chemicals products. Products containing BPA are widely used, and thus, we can find it in the environment: in the air, in the soil, in natural surface water and in sediments, underground water in landfills, and in wastewater. BPA disturbs human and animals’ health. This influences the enzymatic, androgenic, neurological, liver and reproductive systems at different stages of human life: like in fetal stage, children and adults’ stages. Taking these inconveniences into account, it is very important to remove BPA from water. Ultrasonic technology can be considered a verry sustainable and efficient method to remove BPA from water. The advantages of this method is easy to implement on existing water treatment and purification facilities, it does not produce residual compounds that produce sludge, the time required for degradation is of the order of 1-2 hours and the level of degradation is very high. In this work, we presented the studies on the efficiency of ultrasonics under air atmosphere on the degradation of BPA. The influence of the frequency and of some additional compounds such as carbon tetrachloride, FeSO4 7H2O (FS), and ethyl anthraquinone (EAC) was studied. Three different frequencies were used: 1146 KHz, 864 KHz, 580 KHz, at a power of 50 W. It was identified the efficiency of BPA degradation over a period of 60 minutes, with sampling every 15 minutes. Using the LC-MS/MS technique, the degradation compounds were identified that result from the application of ultrasound processes. Pathways of BPA degradation were also proposed.

The 2022-2023 Chilean summer showed increased temperatures and similar burned area, compared to the 2016-2017 season, where more than 500,000 hectares were compromised, mainly in the rural areas. After a brief review, it is revealed that the effects of forest fires on soil and hydrological properties are barely debated in Chile. Here, we showed a climatological analysis where temperature records in the 2016-2017 season were unusual, as well as another unexpected increase in the summer of 2022-2023, resulting in high-severity fires known as ‘mega-fires’ or “storm-fires”. Mega-fires affect forest plantations and native forests mainly from 33º S (Maule Region) to 39º S (Los Ríos Region) and they are expected to become frequent due to climate change, moving from the north to the south. We present an overview of the influence of wildfires on soil components in the most affected areas (inland, Coastal, and Andes ranges), their hydrological impacts, and potential erosion risk due to high winter precipitation. We propose several management practices that could help to prevent or mitigate these events, including pre-and post-fire interventions, such as afforestation and seeding, selective logging, mulching, erosion barriers, soil preparation, and dam monitoring. We argue that any effective plan in fire-prone and affected areas should include a combination of actions taken at the hillslope scale at integral ecosystem management, whose effectiveness should be monitored and verified regionally at the watershed scale.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

Land degradation monitoring and assessment in the Sahel zone has relied substantially on temporal trends of remote sensing-based vegetation indices, which are proxies for the bioproductivity of the land. However, prior studies have shown that negative or positive trends in bioproductivity are not necessarily associated with degradation or improvement of land condition. In this short communication, while acknowledging the contributions of remote sensing-based indices and global-scale datasets to dismantling an outdated desertification narrative, we argue that local land users have much to contribute to our understanding of land degradation, and particularly to ensuring that scientific assessments of degradation capture variables relevant to them. We used the participatory photo elicitation method in three sites in the Senegalese Ferlo in order to elicit local pastoralists’ perspectives on land degradation and identify the indicators that they use to characterize pasture quality, while empowering them to lead the discussion. The discussion revealed indicators far beyond bioproductivity, including livestock performance as well as composition and quality of the herbaceous and woody vegetative cover, invasive species, soil quality and water availability. We found that the pastoralists’ knowledge and interest in the issue could potentially be harnessed more systematically, and at larger scales, in order to build a spatially explicit field-based knowledge base of land degradation complementary to remote sensing-based maps of trends in bioproductivity. Such a dataset could serve as a standalone product or as a reference dataset for development and validation of remote sensing-based indicators.

Sub-micron o/w emulsions coated with chitosan have been used for drug delivery, quorum sensing inhibition and vaccine development. To study interactions with biological systems, nanocapsules have been fluorescently labelled in previous works, but it is often difficult to distinguish the released label from intact nanocapsules. In this study, we present advanced labelling strategies based on FRET measurements for chitosan-coated nanocapsules and investigate their dissolution and degradation. We used FRET measurements of nanocapsules loaded with equimolar concentrations of two fluorescent dyes in their oily core and correlated them with DLS count rate measurement and absorbance measurements during their disintegration by dissolution. Using count rate measurements, we also investigated the enzymatic degradation of nanocapsules using pancreatin and how protein corona formation influences their degradation. Of note, nanocapsules dissolved in ethanol, where FRET decreased simultaneously with count rate, and absorbance caused by nanocapsule turbidity, indicating increased distance between dye molecules after their release. Nanocapsules were degradable by pancreatin in a dose dependent manner, and showed a delayed enzymatic degradation after protein corona formation. We present here novel labelling strategies for nanocapsules that allow us to judge their status and an in vitro method to study nanocapsule degradation and the influence of surface characteristics.

For the majority of lipophilic compounds adipose tissue is traditionally considered as storage depot and only rarely as a target organ. Meanwhile, abnormalities in adipose tissue physiology induced by chemical exposures may contribute to the current epidemic of obesity and metabolic diseases. Polybrominated diphenyl ethers (PBDEs) is a group of lipophilic flame retardants found in majority of human samples in North America. Their ability to alter physiology of adipose tissue is unknown. We exposed pregnant mice to 0.2 mg/kg body weight/day of BDE-47 perinatally. Transcriptomic changes in gonadal adipose tissue were analyzed in male offspring using RNA-seq approach with subsequent bioinformatic analysis. Genes of coagulation and complement cascade, de novo lipogenesis, and xenobiotic metabolism were altered in expression in response to BDE-47 exposure. The affected molecular network included the following hubs: PPARα, HNF1A and HNF4. These findings suggest that adipose tissue should be considered a target tissue for BDE-47, in addition to its role as a storage depot. This study also builds a background for a targeted search of sensitive phenotypic endpoints of BDE-47 exposure, including lipid profile parameters and coagulation factors in circulation. Additional studies are needed to investigate the role of PBDEs as an obesogen.

In "genome editing," a type of genetic engineering, DNA is added, taken away, or changed in an organism's genome. Biomedicine, biotechnology, and synthetic biology, just to name a few, have all gained a lot from how often this method is used. Before the editing process can start, a Double-Strand Breaks (DSB) must be made in the DNA at a specific gene. Researchers have made nucleases, which are sometimes called "molecular scissors," to fix this DSB. Transcription activator-like effector nucleases (TALENs), Zinc-finger nucleases (ZFNs), and homing endonucleases are all examples of protein targets that have been studied and changed. The last part gave an overview of these study projects and explained how to make Cas12a for specific uses. The applications of Cas12a have been extensively studied in recent years, but the protein still holds a lot of promise as a treatment and screening tool. In order to give a quick review of CRISPR-Cas12a and its uses, we will briefly talk about the structure and function of the different parts of the reaction pathway that lead up to the catalysis of the target DNA. Cas12a uses a multistep process to make sure that it is selecting the right DNA. This is a good trait for a device that changes the DNA because it makes it less likely that something bad will happen. Even though data shows that a new CRISPR RNAs (crRNA) molecule can stop Cas12a from randomly destroying ssDNA, it may still hurt the host cell while trying to change the genome. The action of Cas12a catalysis, which is a powerful tool for changing the genome, needs to be changed so that it can be more easily controlled and managed. Using what we know about how Cas12a works, we have made mutants that are less active on ssDNA and more active on dsDNA. So far, only Cas9 and Cas12a, which are both part of the CRISPR family, have been used to change the genome. Because of how similar and different these two endonucleases are, CRISPR can now be used for multiple scientific purposes. Cas12a is better than Cas9 because it makes double-strand breaks (DSBs) that favor Homology-Directed Repair (HDR) over Non-homologous end joining (NHEJ) and can change more than one copy of the genome at the same time. Both Cas9 and Cas12a are being changed to make them better at detecting Protospacer Adjacent Motif (PAM) than they are in their natural state. This will make it possible to start focusing on more genes.

Microplastics (MPs) and nanoplastics (NPs) are distributed and transferred among the four major environmental compartments (air, water, soil, and biota) and have been already found in humans, making crucial to develop remediation technologies to tackle this kind pollution. Photocatalysis can be used to eliminate MPs present in contaminated wastewater effluents before their discharge into waterbodies. In this work, several green TiO2-based semiconductors were prepared using the extrapallial fluid (EPF) of Mytilus edulis sea water mussels as doping precursor. The semiconductors were then used as films or powders to photocatalytically degrade polystyrene (PS) NPs and MPs and polyethylene (PE) MPs. It was found that the obtention of green TiO2-based semiconductors with good characteristics for photocatalytic purposes (anatase crystalline phase, presence of porosity, activity in visible light and high surface area) seems not enough to achieve high degradation efficiency. The operational conditions of the reaction system should be also taken into account. For instance, the convenience of using semiconductors in the form of films can be overcome by their limited exposed surface area or the null adsorption of the semiconductor in the MPs particles. Additionally, crystallinity of the semiconductor can be a more determinant factor to take into account when performing photocatalysis of MPs.

Copper-based nanoparticles were synthesized using the glycine–nitrate process (GNP) by using copper nitrate trihydrate [Cu(NO₃)₂‧3H₂O] as the main starting material and glycine [C₂H₅NO₂] as the complexing and incendiary agent. The as-prepared powders were characterized through X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy. Using Cu(NO₃)₂.3H₂O as the oxidizer (N) and glycine as fuel (G), we obtained CuO, mixed-valence copper oxides (CuO + Cu₂O, G/N = 0.3–0.5), and metallic Cu (G/N = 0.7). The XRD and BET results indicated that increasing the glycine concentration (G/N = 0.7) and reducing particle surface area increased the yield of metallic Cu. The effects of varying reaction parameters such as catalyst activity, catalyst dose, and H₂O₂ concentration on nonylphenol-9-polyethoxylate (NP9EO) degradation were assessed. With a copper‐based catalyst in a heterogeneous system, the NP9EO and total organic carbon removal efficiencies were 83.1% and 70.6%, respectively, under optimum operating conditions (pH, 6.0; catalyst dose, 0.3 g/L; H₂O₂ concentration, 0.05 mM). The results suggested that removal efficiency increased with an increase in H₂O₂ concentration but decreased when the H₂O₂ concentration exceeded 0.0.5 mM. Furthermore, the trend of photocatalytic activity was as follows: G/N = 0.5 > G/N = 0.7 > G/N = 0.3. The G/N = 0.5 catalysts showed the highest photocatalytic activity and resulted in 94.6% NP9EO degradation in 600 min.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

Enzymatic degradation of organic pollutants is a new and promising remediation approach. Peroxidases are one of the most commonly used classes of enzymes to degrade organic pollutants. However, it is generally assumed that all peroxidases behave similarly and produce similar degradation products. In this study, we conducted detailed studies of the degradation of a model aromatic pollutant, Sulforhodamine B dye (SRB dye), using two peroxidases—soybean peroxidase (SBP) and chloroperoxidase (CPO). Our results show that these two related enzymes had different optimum conditions (pH, temperature, H₂O₂ concentration...etc.) for efficiently degrading SRB dye. High-performance liquid chromatography and LC-mass spectrometry analyses confirmed that both SBP and CPO transformed the SRB dye into low molecular weight intermediates. While most of the intermediates produced by the two enzymes were the same, the CPO treatment produced at least one different intermediate. Furthermore, toxicological evaluation using lettuce (Lactuca sativa) seeds demonstrated that the SBP-based treatment was able to eliminate the phytotoxicity of SRB dye, but the CPO-based treatment did not. Our results show, for the first time, that while both of these related enzymes can be used to efficiently degrade organic pollutants, they have different optimum reaction conditions and may not be equally efficient in detoxification of organic pollutants.

Nowadays, the study of preparing silica/rubber composites, which can be used in “green tire”, in energy saving method is fast-growing. In our work, silica modified by using alcohol polyoxyethylene ether (AEO) and 3-Mercaptopropyltriethoxysilane (K-MEPTS) together were investigated. Thermal gravimetric analyzer (TGA) result indicated that both AEO and K-MEPTS could be grafted on the silica surface. Raman spectroscopy confirmed that the AEO could generate a certain steric hindrance for the mercaptopropyl group on K-MEPTS. Silica modified by using AEO and K-MEPTS together can be completely co-coagulated with the rubber in preparing silica/natural rubber (NR) composites by latex compounding method. AEO can form a physical interface between silica and rubber; meanwhile, K-MEPTS can form a chemical interface between silica and rubber. The effects of chemical and physical interface between silica and rubber on dynamic and mechanical performances of silica/NR composites were also given in this research. A proper combination of physical and chemical interface between silica and NR can improve performances of silica/NR composites.

Experimental studies of degradation of two ribonucleosides (guanosine and uridine) were carried out by making use of mechanochemistry. Mechanochemical experiments reveal the decomposition of guanosine and uridine promoted by nickel(II) and carbonate ions into guanine and uracil, respectively which were identified by HPLC and 1H NMR spectroscopy (this applied only to uracil). Additionally, DFT methodologies were used to probe the energetic viability of several degradation pathways, including in the presence of the same ions. Three mechanisms were analysed via ribose ring-opening: dry, single molecule water- and metal-assisted, which confirmed the mechanochemical degradation of ribonucleosides, with nucleobase preservation. These results can be applied to interpret the organic content of terrestrial and extra-terrestrial samples after mechanochemical treatment.

The manuscript presents the comprehensive integrative theory of the etiology and pathogenesis of Alzheimer’s disease - the amyloid degradation toxicity hypothesis - and describes the logic that underlies it.The analysis of amyloid biomarkers and stable-isotope label kinetics (SILK) studies suggest that AD diagnosis is associated with higher cellular uptake of beta-amyloid. Uptake of beta-amyloid by cells is needed for its cytotoxicity, so the uptake rate should correlate with the rate of neurodegeneration. Also, the initial step in forming extracellular aggregates cannot occur in the interstitial fluid due to the extremely low concentration of beta-amyloid but can occur intralysosomally. Therefore, the density of extracellular aggregates should positively correlate with the rate of cellular amyloid uptake. The model, which considers that both cytotoxicity and aggregation of beta-amyloid are defined by cellular uptake, successfully reproduces the probability distribution of AD diagnosis in the population. Cellular uptake of beta-amyloid is mediated by endocytosis. Endocytosed beta-amyloid induces lysosomal permeabilization that occurs without plasma membrane damage. Lysosomal permeabilization explains ion disturbances, such as an accumulation of intracellular calcium, caused by cell exposure to extracellular beta-amyloid. Some amyloid fragments, produced from beta-amyloid by lysosomal proteases, can form membrane channels in lysosomal membranes, which are large enough to leak cathepsins to the cytoplasm. Appearance of proteases in the cytoplasm results in necrosis and/or initiation of apoptosis. If the cell survives, the damage of lysosomes leads to autophagy failure and slow recycling of mitochondria, promoting the production of reactive oxygen species and potentiating cell damage.Considering the above, the integrative theory of AD etiology and pathogenesis can be formulated. The etiology of AD is the membrane channel formation by amyloid fragments produced in lysosomes. The pathogenesis includes lysosomal permeabilization by giant membrane channels, which leak lysosomal proteases into the cytoplasm. The correlation between the density of amyloid aggregates and the probability of AD appears because the intensity of cellular uptake defines both aggregation rates in vivo and cytotoxicity of beta-amyloid.The amyloid degradation toxicity hypothesis is the integrative theory of Alzheimer’s disease (AD). It successfully interprets multiple phenomena and paradoxes associated with AD pathobiology at various levels, from molecular and cellular to biomarkers. The hypothesis explains the limitations of currently used biomarkers of AD and proposes etiology-related parameters. These parameters could be measured in humans and become novel diagnostic and prognostic clinical tools. Based on the proposed framework, we foresee the development of effective medications to treat, stall the progression of, or prevent disease development.

Lithium-ion batteries with improved energy densities have made understanding the Solid Electrolyte Interphase (SEI) generation mechanisms that cause mechanical, thermal, and chemical failures more complicated. SEI processes reduce battery capacity and power. Thus, a review of this area's understanding is important. It is essential to know how batteries degrade in EVs to estimate battery lifespan as it goes, predict, and minimize losses, and determine the ideal time for a replacement. Lithium-ion batteries used in EVs mainly suffer two types of degradation: calendar degradation and cycling degradation. Despite the existence of several existing works in the literature, several aspects of battery degradation remain unclear or have not been analyzed in detail. This work presents a systematic review of existing works in the literature. The results of the present investigation provide insight into the complex relationships among various factors affecting battery degradation mechanisms. Specifically, this systematic review examined the effects of time, side reactions, temperature fluctuations, high charge/discharge rates, depth of discharge, mechanical stress, thermal stress, and the voltage relationship on battery performance and longevity. The results revealed that these factors interact in complex ways to influence the degradation mechanisms of batteries. For example, high charge currents and deep discharges were found to accelerate degradation, while low temperatures and moderate discharge depths were shown to be beneficial for battery longevity. Additionally, the results showed that the relationship between cell voltage and State-of-Charge (SOC) plays a critical role in determining the rate of degradation. Overall, these findings have important implications for the design and operation of battery systems, as they highlight the need to carefully manage a range of factors to maximize battery performance and longevity. The result is an analysis of the main articles published in this field in recent years. This work aims to present new knowledge about fault detection, diagnosis, and management of lithium-ion batteries based on battery degradation concepts. The new knowledge is presented and discussed in a structured and comprehensive way.

In this paper, we propose an unsupervised blind restoration model for images in hybrid degradation scenes. The proposed model encodes the content information and degradation information of images and then uses the attention module to disentangle the two kinds of information. It can improve the ability of disentangled presentation learning for a generative adversarial network (GAN) to restore the images in hybrid degradation scenes, enhance the detailed features of restored image and remove the artifact combining the adversarial loss, cycle-consistency loss, and perception loss. The experimental results on the DIV2K dataset and medical images show that the proposed method outperforms existing unsupervised image restoration algorithms in terms of peak signal-to-noise ratio (PSNR), structural similarity (SSIM), and subjective visual evaluation.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

Over the years, scarcity of fresh potable water has increased the demand for clean water. Meanwhile, with the advent of nanotechnology, the use of nanomaterials for photocatalytic degradation of pollutants in wastewaters has increased. Herein, a new type of nanohybrids of La and Mn co-doped bismuth ferrite (BiFeO₃) nanoparticles embedded into transition metal carbide sheets (MXene) were prepared by a low-cost double solvent sol-gel method, and investigated for their photocatalytic activity. The photoluminescence results showed that pure BFO has highest electron hole recombination rate as compared to all the co-doped BFO/MXene nanohybrids. The larger surface area and higher electron-hole pair generation rate provides suitable environment for fast photo-degradation of organic molecules. The band gap of the prepared nanohybrids was tuned to 1.96 eV having largest BiFeO₃ surface area (147 m²g⁻¹) reported till date. Moreover, the BLFO/MXene and BLFMO-5/Mxene degraded the 92% organic pollutant from water in dark and remaining in light spectrum as compare to undoped BFO/Mxene due to enhancement of the surface area and electron-hole recombination rate upon doping. Therefore, these synthesized nanohybrids could be a promising candidate for photocatalytic applications in future.

Rhabdomyosarcoma (RMS) is the most common soft tissue malignancy in children and adolescents. Respecting the age of the patients and the tumor aggressiveness, investigation of the molecular mechanisms of RMS tumorigenesis is directed toward the identification of novel therapeutic targets. To contribute to a better understanding of the molecular pathology of RMS, we investigated ankyrin repeat domain 1 (ANKRD1), designated as a potential marker for differential diagnostics. In this study, we used three RMS cell lines (SJRH30, RD, and HS-729) to assess its expression profile, intracellular localization, and turnover. They express wild-type ANKRD1, as judged by the sequencing of the open reading frame. Each cell line expressed a different amount of ANKRD1 protein, although the transcript level was similar. According to Western blot analysis, ANKRD1 protein was expressed at detectable levels in the SJRH30 and RD cells (SJRH30>RD), but not in the HS-729, even after immunoprecipitation. Immunocytochemistry revealed nuclear and cytoplasmic localization of ANKRD1 in all examined cell lines. Moreover, the punctate pattern of ANKRD1 staining in the nuclei of RD and HS-729 cells overlapped with coilin, indicating its association with Cajal bodies. We have shown that RMS cells are not able to overexpress ANKRD1 protein, which can be attributed to its proteasomal degradation. The unsuccessful attempt to overexpress ANKRD1 in RMS cells indicates the possibility that its overexpression may be lethal for RMS cells and opens a window for therapeutic targeting.

Agricultural expansion is altering the provision of ecosystem services and seriously affecting the well-being of the indigenous communities still living in forests. In this paper, we evaluate the impact of forest loss and degradation on the indigenous forest dependent communities of Eastern Salta, Argentina, between 2001 and 2015. First, we identified the demand area of ten final ecosystem services for 202 indigenous communities using participatory mapping data. Second, we calculated the remaining usage area using a deforestation geodatabase based on Landsat images. Third, we analyzed the significance of trends in forest productivity processing vegetation spectral indices from MODIS products. By last, we detected changes in the growing season length by evaluating monthly trends in spectral indices. Our results show a reduction of 21% in the area used by indigenous communities for capturing final ecosystem services, and significant negative trends in forest productivity for the demand area of 64% of the communities, indicating that the area of use is not only being reduced, but also remnant forest area is being degraded and the growing season is being shortened. These aspects indicate an important loss in the provision of ecosystem services that deeply affects the wellbeing of indigenous communities.

Polycyclic aromatic hydrocarbons (PAHs), which consist of low-molecular-weight PAHs (LMW-PAHs) and high-molecular-weight PAHs (HMW-PAHs), form an important class of pollutants. Pyrene and benzo[a]pyrene (BaP) are the main pollutants belonging to HMW-PAHs, and their degradation by microorganisms remains an important strategy for their removal from the environments. Extensive studies have been carried out on the isolation and characterisation of microorganisms that actively degrade LMW-PAHs, and to a certain extent, the HMW-PAH pyrene. However, so far, limited work has been carried out on BaP biodegradation. BaP consists of five fused aromatic rings, which confers this compound a high stability, rendering it less amenable to biodegradation. The current review summarizes the emerging reports on BaP biodegradation. More specifically, work carried out on BaP bacterial degradation and current knowledge gaps that limit our understanding of BaP degradation are highlighted. Moreover, new avenues of research on BaP degradation are proposed, specifically in the context of the development of “omics” approaches

The effect of chemical degradation of a sodium alginate solution and the possibility of encapsulation of paprika oleoresin were investigated. To produce sodium alginate oligomers, a depolymerization process was performed using hydrogen peroxide as a decomposition factor. The characteristics of the samples were obtained by measuring the contact angle of the surface, the surface tension of solutions, as well as thermal decomposition in thermo - gravimetric analysis. The obtained solution of alginate oligomers served as the carrier material for immobilization of capsaicin. Capsules were prepared by ionic gelation using a calcium chloride solution as a crosslinking agent. In this way, capsules without and with the core (capsaicin) were prepared and their ability to scavenge free radicals (DPPH) and iron-reducing properties (FRAP) were determined. The stability of the capsules was examined under conditions of the gastric and small intestine. It was found that alginate oligomers can be used in the encapsulation of bioactive compounds and the efficiency is above 80%. Capsule production from alginate oligomers affected their thermal stability. The use of alginate derivatives as a carrier increases the antioxidant properties of the finished product, as well as its ability to reduce iron ions. The use of alginate oligomers as a coating material prevents the active substance from being released too early in the conditions of the small intestine, prolongs the stability of the capsules, and supports their durability in gastric conditions.

Targeted protein degradation is an attractive technology for cancer treatment due to its ability to overcome the unpredictability of small molecule inhibitors that cause resistance mutations. In recent years, various targeted protein degradation strategies have been developed based on the ubiquitin-proteasome system in the cytoplasm or the autophagy-lysosomal system during endocytosis. In this review, we describe and compare technologies for targeted inhibition and targeted degradation of the epidermal growth factor receptor (EGFR), one of the major proteins responsible for the onset and progression of many types of cancer. In addition, we have developed an alternative strategy, called alloAUTO, based on the binding of new heterocyclic compounds to an allosteric site located in close proximity to the EGFR catalytic site. These compounds cause targeted degradation of the transmembrane receptor, simultaneously activating both systems of protein degradation in cells. Damage to EGFR signaling pathways promotes inactivation of Bim sensor protein phosphorylation, which leads to disintegration of the cytoskeleton, followed by detachment of cancer cells from the extracellular matrix and, ultimately, to cancer cell death. This hallmark of targeted cancer cell death suggests an advantage over other targeted protein degradation strategies, namely that the fewer cancer cells survive, the fewer chemotherapy-resistant mutants appear.

Chemical warfare agents (CWAs) are one of the most toxic compounds. Degradation of CWAs using decontamination agents is one of the few ways to protect human health against the harmful effects of CWAs. A ferrate Fe(VI) based potential chemical warfare agent decontaminant was studied for degradation of persistent nitrogen mustard (tris(2-chloroethyl)amine, HN3). By optimizing the reaction conditions, the complete degradation of HN3 was achieved in 4 minutes. The degradation products contained mostly reduced Fe species which confirmed the environmental friendliness of the proposed decontamination solution.

Plastics are extensively used due to their versatility, durability, and low cost. PET stands for Polyethylene terephthalate. PET plastic is widely used all over the world and has many applications ranging from water bottles to fabrics like polyester and many things in between. But its unrestrained use in every field is resulting in heaps and piles of non-biodegradable materials causing damage to the environment and causing pollution. The idea being proposed is to degrade the PET plastic biologically using different bacteria. The bacteria used in this process are Ideonella sakaiensis, Acetobacterium woodii, Pelotomaculum and Methanospirillum hungatei. PET plastic is degraded, yielding Terephthalic Acid (TPA) and Ethylene Glycol (EG) by the action of the bacterium I. sakaiensis. Degradation of EG by A. woodii results in the formation of acetate and ethanol. TPA is degraded by the action of the coculture of Pelotomaculum and M. hungatei thereby yielding methane and acetate. All these products formed have significant commercial uses in various industries. The complete process that is to be carried out can help in achieving sustainability by fulfilling various Sustainable Development Goals set by the United Nations.

Acrylamide (AA) present in food is considered a harmful compound for humans, but it exerts impact on microorganisms too. The aim of the study was to evaluate the impact of AA (at conc. 0-10 µg/mL) on the growth of bacteria (Leuconostoc mesenteroides, Lactobacillus acidophilus LA-5) and yeasts (Saccharomyces cerevisiae, Kluyveromyces lactis var. lactis), which naturally occur in food products. Moreover, we decided to verify whether these microorganisms could decompose acrylamide. Our results proved that AA can stimulated the growth of L. acidophilus and K. lactis. We have also reported, to the best of our knowledge for the first time, that probiotic strain of bacteria L. acidophilus LA-5 is able to degrade AA by amidase production and hence can utilize AA as a source of carbon and nitrogen if they lack in the environment. The conducted Response Surface Methodology indicated that pH as well as incubation time and temperature significantly influenced the amount of ammonia released from acrylamide by the bacteria. Concluding, our studies suggest that some strains of bacteria present in milk fermented products can exert additional beneficial impact by acrylamide degradation and preventing against its harmful impact on human body and other members of intestinal microbiota.

Polymer flooding is an established enhanced oil recovery (EOR) method, still many aspects of polymer flooding are not well understood. This study investigates the influence of mechanical degradation on flow properties of polymers in porous media. Mechanical degradation due to high shear forces may occur in the injection well and at the entrance to the porous media. The polymers that give high viscosity yields at a sustainable economic cost are typically large, MW > 10 MDa, and have wide molecular weight distributions. Both MW and the distributions are altered by mechanical degradation, leading to changes in the flow rheology of the polymer. The polymer solutions were subjected to different degrees of pre-shearing and pre-filtering before injected into Bentheimer outcrop sandstone cores. Rheology studies of injected and produced polymer solutions were performed and interpreted together with in-situ rheology data. The core floods showed a predominant shear thickening behavior at high flow velocities which is due to successive contraction/expansion flow in pores. When pre-sheared, shear thickening was reduced but with no significant reduction in in-situ viscosity at lower flow rates. This may be explained by reduction in the extensional viscosity. Furthermore, the results show that successive degradation occurred which suggests that the assumption of the highest point of shear which determines mechanical degradation in a porous media does not hold for all field relevant conditions.

In this work, silver nanoparticles (AgNPs) were biosynthesized from cashew nutshell liquid (CNSL) by varying the concentration of silver ions and pH of the CNSL extract. The synthesized AgNPs were further characterized to study their surface, structural, and morphological proper-ties, and tested for the degradation of methylene blue (MB) dye. The results of this study showed that depending on the conditions, particles of various sizes, ranging from 1 to 60 nm, and different degrees of stabilization and agglomeration were produced. The concentration of silver ions equal to 3 mM and the pH of the solution of ~ 4.5 (AgNP3) resulted in the most efficient biosynthesis, where particles appeared to be highly stabilized and homogeneously distributed on the surface, exhibiting a small average particle size and a narrow particle size distribution (6.7 ± 6.5 nm). Such particles further showed the highest degradation of MB, where up to 80 % degradation rates were recorded within the first 20 min. Higher concentrations of silver ions and higher pH of the extract resulted in substantial particle agglomeration and unstable synthesis, respectively, which further negatively affected the ability of particles to degrade MB. Finally, visible light showed no significant effect on the degradation of MB by AgNPs with the average degradation rates found to be about the same as under the dark conditions.

Our environment has been impacted by man-made pollutants mainly industries make substantial use of synthetic dyes which exhibit cytotoxicity and have significant environmental consequences. Effective photocatalyst-based approaches for degrading synthetic dyes into less toxic chemical are of great interest. Synthesizing NPs using biological approaches, particularly plant-based approaches offer advantages, decreasing the risk of NPs losing biocompatibility during synthesis, cost-effectiveness, and eco-friendliness. In this study, we employed a green synthesis method to produce manganese oxide nanoparticles (MnO NPs) utilizing leaf extract from the Lathyrus Aphaca plant. The synthesized MnOx NPs were characterized through various techniques; X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier-transform infrared spectroscopy (FTIR), and UV–visible spectroscopy. XRD analysis showed distinct peaks, indicated the presence crystallographic planes within the MnO₂ nanoparticles, thus confirming their crystalline structure. SEM study highlighted closely packed configurations with average size of approximately ≥ 50-70 nm, with well-defined boundaries. EDX analysis showed the presence of elemental manganese (Mn) in the samples, with peaks corresponding to Mn detected at lower energy levels, predominantly represented by MnO. FTIR, showed the presence of the O-O stretching mode at a frequency of 719 cm^-1, the presence of MnO₆ oxides of manganese, and peak at 548 cm^-1 corresponded to the Mn-O stretching mode. Furthermore, the green-synthesized manganese oxide nanoparticles exhibited promising photocatalytic and adsorption capabilities against Methylene Blue (MB) dye, leading to approximately 93.21% degradation of MB when treated with the green-synthesized MnO nanoparticles derived from plant extract. This highlights the efficacy and potential of these nanoparticles in environmental remediation applications, particularly in the degradation of methylene blue contaminants.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Mining for resources extraction may lead to several geological and associated environmental changes due to ground movements, collision with mining cavities and deformation of aquifers. Geological changes may continue in a reclaimed mine area, and the deformed aquifers may entail a breakdown of substrates and an increase in ground water tables, which may cause surface area inundation. Consequently, a reclaimed mine area may experience surface area collapse, i.e. subsidence, and degradation of vegetation health. Thus, monitoring short-term landscape dynamics in a reclaimed mine area may provide important information on the long-term geological and environmental impacts of mining activities. We studied landscape dynamics in Kirchheller Heide, Germany, which experienced extensive soil movement due to longwall mining without stowing, using Landsat imageries between 2013 and 2016. A Random Forest image classification technique was applied to analyse land-use and land-cover dynamics and the growth of wetland areas was assessed using a Spectral Mixture Analysis (SMA). We also analyzed the changes in vegetation health using a Normalized Difference Vegetation Index (NDVI). We observed a 19.9% growth of wetland area within the four years with 87.2% of growth in the coverage of two major waterbodies in the reclaimed mine area. NDVI values indicate that 66.5% of the vegetation of the study area was degraded due to changes in ground water tables and surface flooding. Our results inform environmental management and mining reclamation authorities about the subsidence spots and priority mitigation areas from land surface and vegetation degradation in Kirchheller Heide.

Protoflavones, a rare group of natural flavonoids with a non-aromatic B-ring, are best known of their antitumor properties. The protoflavone B-ring is a versatile moiety that may be explored for other pharmacological purposes, but common cytotoxicity of these compounds is a limitation to such efforts. Protoapigenone was previously found to be active against the lytic cycle of Epstein-Barr virus (EBV). Further, the 5-hydroxyflavone moiety is a known pharmacophore against HIV-integrase. The aim of this work was to prepare a series of less cytotoxic protoflavone analogs, and to study their antiviral activity against HIV and EBV. Twenty-seven compounds including 18 new derivatives were prepared from apigenin through oxidative de-aromatization and subsequent continuous-flow hydrogenation, deuteration, and/or 4′-oxime formation. One compound was active against HIV at the micromolar range, and 3 compounds showed significant activity against the EBV lytic cycle at the medium-low nanomolar range. Among these, protoapigenone 1′-O-isopropyl ether (6) was identified as a promising lead due to its 73-times selectivity of its antiviral over its cytotoxic effect, which exceeds that of protoapigenone by 2.4-times. Our results open new opportunities to design new, potent and safe anti-EBV agents based on the natural protoflavone moiety.

An immiscible blend of poly(hydroxy ether of bisphenol-A) (phenoxy) and poly(1,4-butylene terephthalate) (PBT) with phase separation was observed in as-blended samples. However, compatibilization of the phenoxy/PBT blends can be promoted through chemical exchange reactions of phenoxy with PBT upon annealing. In contrast to the as-blended samples, the annealed phenoxy/PBT blends had a homogeneous phase with a single T_g that could be enhanced by annealing at 260°C. Infrared (IR) spectroscopy demonstrated that phase homogenization could be promoted by annealing of the phenoxy/PBT blend, where alcoholytic exchange occurred between the dangling hydroxyl group in phenoxy and the carbonyl group in PBT in the heated blends. The alcoholysis reaction changes the aromatic linkages to aliphatic linkages in carbonyl groups, which initially led to the formation of a graft copolymer of phenoxy and PBT with an aliphatic/aliphatic carbonyl link. The progressive alcoholysis reaction resulted in the transformation of the initial homopolymers into block copolymers and finally into random copolymers, which promoted phase compatibilization in blends of phenoxy with PBT. Due to the fact that the amount of copolymers increased upon annealing, crystallization of PBT was inhibited by alcoholytic exchange in the blends.

In this review, we covered the recent advances in synthesis of gold nanoparticles and their uses in degradation of dyes. This study provides framework to develop a low cost, ecofriendly and highly efficient synthesis of gold nanoparticles. These synthetic methods do not produce any toxic byproduct. The present study is focus on removal of dyes by Au-NPs because gold nanoparticles act as good absorbent for dyes in short time. Synthesis of Au-NPs from plant extract e.g. marine alga, Scutellarin Barbata, A.nigra, Fruit peels, Bacillus marisflavi from raw silk cocoons, amylopectin and poly acrylic acid, L.asparagine, Grephene oxide, IPEI coated Au-NPs. The synthesizes Au-NPs were used further for removal of dyes like methylene blue (MB), Rhodamine B (RB) Degradation, methylene orange, acid red degradation, Congo red.

The biological synthesis of nanoparticles has been emerging as an environmentally benign and eco-friendly method owing to its cost-effectiveness and high efficiency. Recently, the biological synthesis of semiconductor and metal-doped semiconductor nanoparticles with enhanced photocatalytic degradation efficiency and anticancer and antibacterial properties have gained tremendous attention. In pursuit of this purpose, for the first time, we biosynthesized zinc oxide (ZnO) and silver/ZnO nanocomposites (NCs) as semiconductor and metal-doped semiconductor nanoparticles, respectively, using the cell-free filtrate (CFF) of Lysinibacillus sphaericus bacterium. The biosynthesized ZnO and Ag/ZnO were characterized by various techniques such as ultraviolet-visible spectroscopy, X-ray diffraction, Fourier-transform Infrared spectroscopy, Field-emission scanning electron microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The photocatalytic degradation potential of these semiconductor/metal-semiconductor nanoparticles was evaluated against the degradation of azo dye methylene blue (MB) under simulated solar irradiation. Ag/ZnO showed 90.7 ± 0.91% photocatalytic degradation of MB, compared to 50.7 ± 0.53% by ZnO in 120 min. The cytotoxicity of ZnO and Ag/ZnO on human cervical HeLa cancer cells was determined using an MTT assay. Both nanomaterials exhibited cytotoxicity in a concentration-dependent and time-dependent manner on HeLa cells. The antibacterial activity was also determined against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus). Compared to ZnO, Ag/ZnO NPs showed higher antibacterial activity. Hence, the biosynthesis of semiconductor nanoparticles could be a promising strategy for developing hybrid metal/semiconductor nanomaterials for different biomedical and environmental applications.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

With the wide application of flow sensor, their reliability under extreme conditions has been concerned in recent years. The reliability of a Micro Electro Mechanical Systems flow sensor under temperature (Ts) is researched in this paper. Firstly, the Step-stress accelerated degradation test is designed. Because this flow sensor consists flow sensor chip and signal processing system, the accelerated degradation testing is implemented, respectively. While the results show that the biggest drift is 3.15% for flow sensor chips with 150℃ conditions, and 32.91% for this flowmeter. By analysis, it could be found that the attenuation of the signal processing system is significant to the degeneration of this flowmeter. The minimum drift of the signal processing system accounts for 82.01% of this flowmeter. Secondly, using the Coffin-Manson model, the relationship between cycle-index and Ts is established. And the lifetime with different Ts is estimated by the Arrhenius model. In addition, the Weibull distribution is applied to evaluate the lifetime distribution. Finally, the reliability function of the Weibull distribution is demonstrated, and the survival rate within one year is 87.69% with 85℃ conditions. Thus, by the application of accelerated degradation testing, the acquired results are innovative and original. This research illustrates the reliability research, which provides a relational database for the application of this flow sensor.

Fipronil is an insecticide widely used in the agricultural and veterinary sectors for its efficacy in pest control. The presence of fipronil in the environment is mainly due to agricultural and domestic practices and is frequently found in different types of environmental matrices in concentrations ranging from µg/L to mg/L and can be hazardous to non-target organisms due to its high toxicity. This study was carried out to obtain and characterize microorganisms from soil which are capable of biodegrading fipronil that could be of great biotechnological interest. For this purpose, a bioprospecting was carried out using fipronil (0.6 g/L) as the main source of carbon and nitrogen for growth. Once obtained, the strain was identified by sequencing the 16S ribosomal RNA (rRNA) gene and the capacity to degrade fipronil was monitored by GC-MS. Our study showed the presence in soil samples of the strain identified as Enterobacter chengduensis, which was able to metabolize fipronil and its metabolites during the mineralization process. Enterobacter chengduensis was able to biodegrade fipronil (96%) and its metabolites fipronil-sulfone (92%) and fipronil-sulfide (79%) in 14 days. Overall, the results of this study provided a bacterium with great potential that could contribute to the degradation of fipronil in the environment.

The prevalence of antiviral drugs (AVTs) has seen a substantial increase in response to the COVID-19 pandemic, leading to heightened concentrations of these pharmaceuticals in wastewater systems. The hydrophilic nature of AVTs has been identified as a significant factor contributing to the low degradation efficiency observed in wastewater treatment plants. This characteristic often necessitates the implementation of additional treatment steps to achieve complete degradation of AVTs. Semiconductor-based photocatalysis has garnered considerable attention due to its promising potential in achieving efficient degradation rates and subsequent mineralization of pollutants, leveraging the inexhaustible energy of sunlight. However, in recent years, there have been few comprehensive reports that have thoroughly summarized and analyzed the application of photocatalysis for the removal of AVTs. This review commences by summarizing the types and occurrence of AVTs. Furthermore, it places a significant emphasis on delivering a comprehensive summary and analysis of the characteristics pertaining to the photocatalytic elimination of AVTs. Ultimately, the review sheds light on the identified research gaps and key concerns, offering invaluable insights to steer future investigations in this field.

: The stability of semiconductor catalysts is a very important property in the field of catalytic reactions. Materials necessitate resistance to mechanical abrasion and chemical erosion for better overall performance. In this work, high crystallinity BiOCl nanosheets were prepared by a simple hydrothermal method. The photocatalysts demonstrate full UV light absorption ability and excellent photocatalytic norfloxacin degradation performance. 84 % of highly toxic norfloxacin were photocatalytically eliminated within 180 min. The internal structure and surface chemical state of BiOCl were analyzed by SEM, TEM, Raman, FTIR, UV-vis, XPS, and other techniques. Such high crystallinity makes BiOCl molecules closely arranged and the molecular chains strongly connected, thus exhibiting a high level of photocatalytic stability and recyclability.

This review focus on a critical analysis of nanocatalysts for Advanced Reductive Processes (ARP) and Oxidation Processes (AOP) designed for the degradation of poly/perfluoroalkyl substances (PFAS) in water. Ozone, ultraviolet and photocatalyzed ARP and/or AOP will be the basic treatment technologies. Besides the review of the nanomaterials with greater potential as catalyst for advanced processes of PFAS in water, the perspectives for its future development considering sustainability considerations will be discussed. Moreover, a brief analysis of the current state of the art of the ARP and AOP for the treatment of PFAS in water will be presented.

Micro turbojets are used for propelling radio-controlled aircraft, aerial targets and personal air vehicles. When compared to full-scale engines, they are characterized by relatively low efficiency and durability. In this context, the degraded performance of gas path components could lead to an unacceptable reduction in the overall engine performance. In this work, a data-driven model based on a conventional Artificial Neural Network (ANN) and an extreme learning machine (ELM) was used for estimating the performance degradation of the micro turbojet. The training datasets containing the performance data of the engine with degraded components were generated using the validated GSP model and the Monte Carlo approach. In particular, compressor and turbine performance degradation were simulated for three different flight regimes. It was confirmed that component degradation had a similar impact in flight than at sea level. Finally, the datasets were used in the training and testing process of the ELM algorithm with four different input vectors. Two vectors had an extensive number of virtual sensors, and the other two were reduced to just fuel flow and Exhaust Gas Temperature. Even with the small number of sensors, the high prediction accuracy of ELM was maintained for takeoff and cruise but was slightly worse for variable flight conditions.

Novel model of biodegradable PHA copolymer films preparation was applied to evaluate biodegradability of various PHA copolymers and discuss its biomedical applicability. In this study, we illustrate the potential biomaterial degradation rate affectability by manipulation of monomer composition via controlling biosynthetic strategies. Within the experimental investigation, we have prepared two different copolymers of 3-hydroxybutyrate and 4-hydroxybutyrate – P(3HB-co-36 mol.% 4HB) and P(3HB-co-66 mol.% 4HB), by cultivating thermophilic bacterial strain Aneurinibacillus sp. H1 and further investigated its degradability in simulated body fluids (SBFs). Both copolymers revealed faster weight reduction in synthetic gastric juice (SGJ) and artificial colonic fluid (ACF) than simple homopolymer P3HB. In addition, degradation mechanisms differed across tested polymers, according to SEM micrographs. While incubated in SGJ, samples were fragmented due to fast hydrolysis sourcing from substantially low pH, which suggest abiotic degradation as the major degradation mechanism. On the contrary, ACF incubation indicated obvious enzymatic hydrolysis. Further, no cytotoxicity of the waste fluids was observed on CaCO-2 cell line. Based on these results in combination with high production flexibility, we suggest P(3HB-co-4HB) copolymers produced by Aneurinibacillus sp. H1 as very auspicious polymers for intestinal in vivo treatments.

Ofloxacin is a highly efficient and widely used antibiotic drug. It is classified as a refractory pollutant due to its poor biodegradability. Consequently, it is commonly found in water sources, requiring efficient methods for its removal. Advanced Oxidation Processes (AOPs) offer efficient alternatives since those yield complete degradation not achieved in adsorption or membrane processes. Previous studies suggest ofloxacin degradation follows a pseudo-first or -second order processes, whereas for full removal of refractory pollutants – lower pseudo-orders are required. Monitoring the actual “pseudo-order” degradation kinetics of ofloxacin is needed to evaluate any proposed AOP process. This study presents a simple procedure to evaluate pseudo-orders of AOPs. Photolysis of 20 mM ofloxacin solutions follow pseudo-zero order kinetics, with half-life times (t_1/2) of approx. 60 min. TiO₂ heterogenous catalyst show to have no influence at low concentration (0.2 mg L^-1) but a significant reduction of half-life time (t_1/2 = 20 min) and increase in pseudo-order (0.8) is measured at 2.0 mg L^-1. Similar results are obtained with homogenous catalysis by 2.0 mg L^-1 H₂O₂. The combination of H₂O₂ and TiO₂ catalysts shows additional reduction in half-time life with increase in the pseudo-order to 1.2. The conclusions are (1) heterogenous and homogenous photocatalysis can effectively degrade ofloxacin, (2) combined photocatalysis yields higher pseudo-order, being less prone to achieve full removal, (3) analysis of specific pseudo-orders in AOPs of refractory pollutants helps to further elucidate the efficiency of the processes.

Alzheimer's disease (AD) is the most common cause of dementia and affects millions of people around the world. Neuronal death in AD is initiated by the toxic action of oligomeric amyloid-β (Aβ) peptides. The formation of membrane channels by Aβ is a primary molecular action and does not require any other proteins. Channels are formed by short amyloid fragments faster and more frequently than by full-length peptides. The channel formation is dependent on an electrostatic interaction between a positively charged peptide and a negatively charged membrane. Negative membranes can be found in several locations of a cell – the inner leaflet of plasma membrane, mitochondria, and lysosomes, which all are well-known cellular targets in AD. Considering that the amyloid enters a cell by endocytosis and is exposed to lysosomal enzymes, we propose the amyloid degradation toxicity hypothesis. Endopeptidases degrade the endocytosed peptide. Produced fragments form membrane channels, which can transfer various ions (including protons) and even relatively large compounds. The neutralization of lysosomal content inactivates enzymes, which fails the whole system of recycling cellular content, including autophagy. The permeabilization of lysosomes could also lead to cell death through necrotic and apoptotic mechanisms. We discuss several mechanisms that describe how amyloid degradation products reach plasma and mitochondrial membranes, and form membrane channels. The pathogenesis of AD is discussed at various levels in a context of how the primary molecular mechanism of membrane channel formation could progress into the disease state. The discussion starts at the molecular level and extends to why the development of a disease takes years and is closely associated with aging. The proposed hypothesis offers an interpretation to several clinical observations such as the involvement of iron metabolism and an inverse association between developing Alzheimer's disease and cancer. Predictions about potential biomarkers and effectiveness of future treatments are discussed.

Silicone RTV-based engineering rubber composite products have been widely used for several applications in various fields as a major component such as structure, automotive, and medical. In its application, the rubber composite product is placed in an open area that is directly exposed to sunlight and rain. It has a significant negative impact on changes in chemical and rheological properties, making the product life of rubber composite products shorter. Therefore, in this study, changes in the chemical and rheological properties of both isotropic and anisotropic magnetorheological elastomer (MRE) treated with accelerated weathering were studied compared to untreated specimens with specimens that had been treated. MRE specimens with 40% by weight CIP were prepared with no current excitation and another sample were made under 1.5 T of magnetic flux density. Each specimen was treated in an accelerated weathering machine Q-Sun Xe-1 Xenon Test Chamber with a UV light exposure cycle for 102 minutes and 18 minutes of UV light combined with water spray for 24 hours followed by a condensation cycle of 4 hours in a dark period. Material characterization was carried out using FTIR and Rheometer to determine the changes in chemical and rheological properties. The morphological analysis results showed that the surface was rough and more cavities occurred after being given weather treatment. Rheometer test results showed a decrease in storage modulus in each MRE specimen that had been treated compared to untreated MRE specimens. Meanwhile, FTIR testing showed a change in wave peak between untreated and treated MRE specimens.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

Entangled metallic wire material (EMWM) can be utilized as a novel elastic element in vibration isolation devices for mechanical actuators. This paper presents a vibration experiment aimed at investigating the degradation behavior of mechanical performance in EMWM under cyclic compressive environment. An electric vibration testing system, coupled with an isolation structure, is employed to apply compressive loads to the EMWM specimens. Through visual observations and quasi-static compression tests, the variations in geometric morphology and mechanical properties are studied, considering different relative densities and stress amplitudes. The results incidate a significant reduction in the compressed dimension of the specimens as the number of cycles increases, without any wire fractures or wear. Moreover, the mechanical properties exhibit an increasing secant modulus and a decreasing loss factor. These variations ultimately lead to a gradual deviation of the vibration characteristics of the isolation structure from its design state. To predict the mechanical property degradation of EMWM, prediction models are proposed, incorporating dimension, modulus and damping by fitting the obtained results. This research provides valuable experimental data and presents an effective method to determine the operational lifetime of vibration isolators utilizing EMWM.

Aortic aneurysms (AA) occur in 4.8% of people causing 150,000 deaths annually. While endovascular aneurysm repairs reduce surgical morbidity, device-related failures (leak/displacement) are frequent highlighting the need for test models that better represent the mural geometry and compliance changes in human AAs. We aimed to develop and characterise an ex vivo porcine aortic model of AA. The optimal duration of tissue elastase exposure to emulate AA changes in elastin microstructure and content was determined using porcine aortic rings. Elastase-induced changes were quantified morphologically, and mechanical properties assessed via ring tensile testing. Subsequent experiments tested the potential for localised elastase treatment in a 1 cm segment of porcine aorta using a specially designed 3D printed test rig. The effect on pressure-diameter behaviour was investigated via inflation-extension testing. Elastase treatment produced time dependent decreases in elastin, resulting in an increased tensile modulus and circumferential length in the ring samples in the final phase of the J-shaped tissue stress-strain curves. In whole aortic segments, localised elastase-induced luminal degradation was successfully limited to a central region. The degree of elastin degradation achieved was sufficient to cause localised dilation with respect to controls under physiological pressures. Localised elastin degradation in porcine aortic segments is feasible and emulates the changes seen clinically in aortic aneurysms.

Abstract: Targeted ubiquitination and proteasomal degradation regulates various cellular pathways, and the discovery that CPT induced rapid proteasomal degradation of topoI is the primary mechanism of CPT resistance was novel and compelling. CPTs are used extensively to treat various solid tumors like colorectal, gastric, pancreatic, ovarian and small cell lung cancer. The response rate is low and the classical mechanisms of drug resistance are yet to be validated. Remarkably, CPT resistant cells degrade topoI rapidly by UPP and recently we’ve published the molecular determinants of this pathway. To further understand the UPP mediated CPT resistance mechanism we used targeted proteasome prohibition by ixazomib (MLN9708) to stabilize topoI and determine its impact on CPT resistance. CPT resistant and sensitive cancer lines were both treated with ixazomib in combination with CPT. The CPT induced rate of topoI degradation, and its stabilization by ixazomib, was visualized and estimated by immunohistochemistry, immunofluorescence and immunoblotting assays, MTT and subG1 assays provided the drug sensitivity. Our results demonstrate that cells that degrade topoI rapidly are very resistant to CPT, and ixazomib significantly inhibits CPT induced topoI degradation. Notably, inhibition of proteasomal degradation by ixazomib overcomes the drug resistance and sensitizes the cells for CPTs.

A rapid and appropriate genetic and metabolic acclimation, which is crucial for plants’ survival in a changing environment, is maintained due to the coordinated action of plant hormones and cellular degradation mechanisms influencing proteostasis. The plant hormone abscisic acid (ABA) rapidly accumulates in plants in response to environmental stress and plays a pivotal role in the reaction to various stimuli. Increasing evidence demonstrates a significant role of autophagy in controlling ABA signaling. This field has been extensively investigated and new discoveries are constantly being provided. We present updated information on the components of the ABA signaling pathway, particularly on transcription factors modified by different E3 ligases. Then, we focus on the role of selective autophagy in ABA pathway control and review novel evidence on the involvement of autophagy in different parts of the ABA signaling pathway that are important for crosstalk with other hormones, particularly cytokinins and brassinosteroids.

Though innovations for sustainable management of natural resources have emerged over time, the rising demand for nature based health solutions and integration of endemic flora into global value chains could have adverse impacts on ecosystems. The ecological risks in the exploitation of wild medicinal plant resources are exacerbated by a myriad of agrotechnological risks and challenges that highly constrain their domestication. Successful exploitation and commercialization of medicinal plants thus require a clear understanding of their demand and production systems or value chain analysis. Accordingly there is need for innovative approaches towards their integration into global value chains. Since quality and safety, traceability, certification, as well as, consumer tastes and preferences are critical drivers in purchasing decisions by global consumers, they are inadvertently exploited to weaken Indigenous knowledge (IK), undermine common property rights and entrench value chains that favour a few elite buyers. This tend to create pervasive incentives for overexploitation of medicinal plant resources and environmental degradation. Potential solution lies in the recognition of drivers of vulnerability to environmental degradation and the innovative use of policy bricolage, feedback loops and interactions between knowledge, power and agency on one hand, and collective action and property rights institutions on the other hand. We conceptualise a framework that can mediate a transformational agenda and enhance systematic understanding of sustainability lenses in endemic medicinal plant resources value chains. This could in turn strengthen IK, enhance collective action and promote participation of local actors with positive impact on the utilisation and integration of endemic medicinal plant resources into global value chains.

Contamination of the environment by petroleum products is a growing concern worldwide, and strategies to remove these contaminants have been evaluated. One of these strategies is biodegradation, which consists of the use of microorganisms. Biodegradation is significantly improved by increasing the temperature of the milieu, thus, the use of thermophiles, microbes that thrive in high-temperature environments, will render this process more efficient. For instance, various thermophilic enzymes have been used in industrial biotechnology because of their unique catalytic properties. Biodegradation has been extensively studied in the context of mesophilic microbes, and the mechanisms of biodegradation of aliphatic and aromatic petroleum hydrocarbons have been elucidated. However, in comparison, little work has been carried out on the biodegradation of petroleum hydrocarbons by thermophiles. In this paper, a detailed review of the degradation of petroleum hydrocarbons (both aliphatic and aromatic) by thermophiles has been carried out. This work has identified the characteristics of thermophiles, and unravelled specific catabolic pathways of petroleum products that are only found in thermophiles. Gaps that limit our understanding of the activity of these microbes have also been highlighted, and finally, different strategies that can be used to improve the efficiency of degradation of petroleum hydrocarbons by thermophiles have been proposed.

This study investigates the historical variability in annual average precipitation in the northwest region of Mexico, aiming to evaluate the cumulative impact of precipitation on soil degradation and associated risks posed by rainfall. Despite being known as "The Agricultural Heart of Mexico," the region's soil has experienced significant damage to its granulometric structure due to unpredictable rainfall patterns attributed to climate change. Sixteen historical series of average annual rainfall were analyzed as stationary stochastic processes for spectral analysis. The results revealed exponential decay curves in each radial spectrum, indicating a linear relationship between frequency and amplitude. These curves identified initial impulses correlated with moments of severity for structural damages caused by rainfall-induced degradation. The degradation process, exacerbated by water stress, accelerates, as evidenced by maps illustrating approximately 75% soil damage. In the context of climate change and the uncertainty surrounding soil responses to extreme meteorological events, understanding this phenomenon becomes crucial. Recognizing the dynamic nature of soil responses to environmental stressors is essential for effective soil management. Emphasizing the need to employ numerical processes tailored to new environmental considerations related to observed soil damages is crucial for sustainable soil management practices in any region.

The presented work studies the processes of synthesis of nitrogen-containing structures of ZnO using atmospheric pressure microwave nitrogen plasma and investigates their photocatalytic activity in the processes of degradation of 2,4-dinitrophenol and the antibiotic ciprofloxacin when irradiated with sunlight. The work proposes an effective method for formation of photosensitive ZnO powders. Due to the features of plasma treatment in the open atmosphere of zinc metal microparticles, ZnO structures are formed with sizes from hundreds of nanometers to several micrometers with various micromorphologies. High photoactivity was demonstrated (rate constants 0.036 min-1 and 0.051 min-1) of synthesized ZnO structures during photo-degradation of 2,4-dinitrophenol and ciprofloxacin, respectively, when exposed to solar radiation. Photo-active structures of ZnO synthesized using microwave nitrogen plasma can find application in processes of mineralization of toxic organic compounds.

It is important to develop new antibacterial drugs since the emergence of bacterial resistance to available antibiotics. Metal nanoparticles have the potential to combat antibiotic resistance and are effective antibacterial agents. Here, we demonstrate the biogenic production of zinc nanoparticles using Rhododendron arboreum stem bark. The biosynthesized ZnNPs were characterized through different analytical techniques such as UV-vis, FTIR, EDX, SEM, and XRD. Clinical isolates such as E. coli, S. aureus, and K. pneumonia were used to check the antibacterial efficacy of the biosynthesized zinc nanoparticles. The MIC and MBC values against K. pneumonia, S. aureu, and E. coli were found to be 34±0.21 and 11.71±0.47, 47±0.11 and 23.86±0.84 and 94±0.18 and 40.43±0.16 µg/mL, respectively. It dramatically decreased the integrity of the cell membrane and markedly increased the permeability of both inner and outer membranes. The green synthesized ZnNPs have good catalytic activity. It degraded 65% of methyl orange dye within 6h when the mixture was kept in direct sunlight, thus demonstrating good photodegradation potential and can be employed as a good photocatalyst. According to these results, biosynthesized zinc nanoparticles could be a potential therapy option for controlling bacterial pathogenesis and an effective photocatalyst for the elimination of hazardous water contaminants.

In order to realize the performance degradation trend prediction accurately, a prediction method based on multi-domain features and temporal convolutional network (TCN) is proposed. Firstly, construct a high-dimensional feature set in the multi-domain of vibration signals, and use comprehensive evaluation indicators to preliminarily screen performance degradation indexes with good sensitivity and strong trend. Secondly, the kernel principal component analysis (KPCA) method is adopted to eliminate redundant information between multi-domain features, and construct a health index (HI) based on convolutional auto-encoder (CAE) network. Thirdly, a TCN-based performance degradation trend prediction model is constructed, and direct multi-step prediction is used to predict the performance degradation trend of the monitored object. On this basis, the validity of the proposed method is verified using the bearing public data, and it is successfully applied to performance degradation trend prediction of rolling contact fatigue specimen. The results show that the feature set can be reduced from 14 dimensions to 4 dimensions by using KPCA, while 98.33% of the information of the original feature set is retained. Furthermore, the method of constructing HI based on CAE network is effective. The change process of the HI constructed truly reflects the performance degradation process of the rolling contact fatigue specimen. Compared with the two commonly used HI construction methods, auto-encoding (AE) network and gaussian mixture model (GMM), this method has obvious advantages. At the same time, the prediction model based on TCN can accurately predict the performance degradation of the rolling contact fatigue specimen with the root mean square error 0.0146 and the mean absolute error 0.0105, which has better performance and higher prediction accuracy than the prediction model based on the long short-term memory (LSTM) network and the gated recurrent unit (GRU). This method has general significance and may be extended to the performance degradation prediction of other mechanical equipment/parts.

Photocatalytic degradation plays a crucial role in wastewater treatment, and the key to achieving high efficiency is to develop photocatalytic systems that possess excellent light absorption, carrier separation efficiency, and surface-active sites. Among various photocatalytic systems, S-type heterojunctions have shown remarkable potential for efficient degradation. This work delves into construction of S-type heterojunctions of ternary indium metal sulfide and bismuth ferrite nanofibers with introduction of sulfur vacancy defects and morphology modifications to enhance the photocatalytic degradation performance. Through the impregnation method, BiFeO₃/Zn₂S₄ heterojunction materials were synthesized and optimized30% BiFeO₃/Zn₂S₄ heterojunction exhibited superior photocatalytic performance with higher sulfur vacancy concentration than Zn₂S₄. The in-situ XPS results demonstrate that the electrons between Zn₂S₄ and BFO are transferred via S-Scheme, and after modification, Zn₂S₄ has a more favorable surface morphology for electron transport, and its flower-like structure interacts with the nanofibers of BFO, which has a further enhancement of the reaction efficiency for degrading pollutants. This exceptional material demonstrated a remarkable 99% degradation of Evans blue within 45 min and a significant 68% degradation of ciprofloxacin within 90 min. This work provides a feasible idea for developing photocatalysts to deal with the problem of polluted water resources under practical conditions.

The PII protein is an evolutionary highly conserved regulatory protein from bacteria to higher plants. In bacteria it modulates the activity of several enzymes, transporters and regulatory factors by interacting with them and thereby regulating important metabolic hubs like carbon/nitrogen homeostasis. More than two decades ago the PII protein was characterized for the first time in plants, but its physiological role is still not sufficiently resolved. To gain more insights into the function of this protein, we investigated the interaction behaviour of AtPII with candidate proteins by BiFC and FRET/FLIM in planta and with GFP/RFP traps in vitro. In the course of these studies we found that AtPII interacts in chloroplasts with itself as well as with known interactors like NAGK in dot-like aggregates, which we named PII foci. In these novel protein aggregates AtPII interacts also with yet unknown partners, which are known to be involved in plastidic protein degradation. Further studies revealed that the C-terminal part of AtPII is crucial for the formation of PII foci. Altogether, the presented results indicate a novel mode of interaction for PII proteins with other proteins in plants, which may be a new starting point for the elucidation of physiological functions of PII proteins in plants.

A bacterial strain that could effectively degrade DEHP was isolated from the activated sludge and identified as Bacillus sp. by DNA sequencing. The biochemical degradation pathway of DEHP was further analyzed by GC-MS, and the results showed that DEHP was first decomposed into phthalates (DBP). Diuretic sylycol (DEP) was then generated, and phthalates (PA) were generated by a continuous de-ehelateization reaction. Phthalic acid (PA) was oxidized, dehydrogenated, and decarboxylated into protocatechins. Protocatechins enter the TCA cycle through orthotopic ring opening.　To enhance DEHP degradation, sodium alginate and calcium chloride were used as embedding and cross-linking materials, and the strain was immobilized. The immobilization conditions were optimized via an orthogonal experiment, and the results showed that the optimal immobilization conditions were SA mass fraction of 4%, CaCl2 mass fraction of 5%, ratio of bacteria to SA of 1:1, and the crosslinking time of 6 hours. The immobilized bacteria agent was further applied to MBR systems. The results showed that the removal rate of DEHP (5mg/L) in the system by immobilized bacteria was 91.9%, which is significantly higher than that of free bacteria. The 3, 4-dioxygenase gene and microbial community dynamics were analyzed by q-PCR and Illumina Miseq sequencing. The q-PCR results showed that the number of copies of 3, 4-dioxygenase gene in the immobilized system was significantly higher than that of free bacteria. Illumina Miseq sequencing results showed that Micromonospora, Rhodococcus, Bacteroides and Pseudomonas were the dominant generas in the MBR system. The analysis of bacterial community structure indicated that immobilization technology had a positive impact on the system stability. The results implied that this immobilized technique had potential applications in DEHP wastewater treatment.