Patient symptoms play a critical role in disease progression and diagnosis, yet they are most often captured in unstructured clinical notes. This study explores use of large language models (LLMs) for extracting patient symptoms from clinical notes, comparing their performance against rule-based information extraction (IE) systems, like BioMedICUS. By fine-tuning an LLM on diverse corpora from multiple healthcare institutions, we aimed to improve symptom extraction accuracy and efficiency with symptoms related to acute and post-acute sequelae of SARS-CoV-2. We also conducted prevalence analysis to highlight significant differences in symptom prevalence across corpora and performed fairness analysis to assess the model's equity across race and gender. Our findings indicate that while LLMs can match the effectiveness of rule-based IE methods, they face significant challenges related to demographic bias and generalizability due to variability in training corpora. This evaluation revealed overfitting and insufficient generalization, especially when models were trained predominantly on limited datasets with single annotator bias. This study also revealed that LLMs offer substantial advantages in efficiency, adaptability, and scalability for biomedical IE, marking a transformative shift in clinical data extraction processes. These results provide real-world evidence of the necessity for diverse, high-quality training datasets and robust annotation processes to enhance LLM’s performance and reliability in clinical applications.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

In the field of Natural Language Processing (NLP), Large Language Models (LLMs) have shown great potential in document-level event extraction tasks, but existing methods face challenges in the design of prompts. To address this issue, we propose an optimization strategy called "Definition-driven Document-level Event Extraction (DDEE)." By adjusting the length of the prompt and enhancing the clarity of heuristics, we have significantly improved the event extraction performance of LLMs. We used data balancing techniques to solve the long-tail effect problem, enhancing the model's generalization ability for event types. At the same time, we refined the prompt to ensure it is both concise and comprehensive, adapting to the sensitivity of LLMs to the style of prompts. In addition, the introduction of structured heuristic methods and strict limiting conditions has improved the precision of event and argument role extraction. These strategies not only solve the prompt engineering problems of LLMs in document-level event extraction but also promote the development of event extraction technology, providing new research perspectives for other tasks in the NLP field.

This study introduces a novel computational approach for testing conditional independence (BB CI test) within causal Directed Acyclic Graphs (DAGs), leveraging Bayesian non-parametric bootstrap and machine learning techniques. Our method offers an alternative for validating the assumptions underpinning causal DAGs. Through simulation studies and an industrial case analysis, we demonstrate the test procedure in accurately assessing conditional independence, comparing it with the Generalized Covariance Measure (GCM) test. Our findings suggest that the BB CI test is advantageous in scenarios where existing methods may falter due to violations of model assumptions. This research contributes to the causal inference literature by providing a computational tool for researchers and practitioners to validate causal models.

The extraction methods for carotenoids, xanthophylls and chlorophylls are essential processes involved in the recovery of bioactive compounds from a wide variety of natural sources, including plants, marine organisms, microorganisms and animals. These bioactive compounds, characterized by their significant functional and structurally active properties, play a crucial role in various industries, such as pharmaceuticals, nutraceuticals and food. Due to their presence in small quantities and conjugated form in nature, the extraction of these compounds can be laborious and often requires meticulous purification steps. Interestingly, the primary and secondary metabolites present in plants contribute significantly to the production of these bioactive compounds, adding to their complexity and importance. Notably, carotenoids, as natural pigments with antioxidant and nutritional properties, are known for offering numerous health benefits and are instrumental in various biological processes, including the photoprotection of plants and the prevention of chronic degenerative diseases. It is fascinating to observe that by-products generated from agricultural activities and food processing serve as abundant sources of these bioactive compounds, aligning with the principles of the circular economy and sustainable resource management. Given the diverse health benefits and multifaceted applications of these natural pigments, there is a growing interest in not only extracting but also utilizing them for industrial, nutritional and pharmacological purposes.

With the rapid development of new energy vehicles and the digital electronics industry, the demand for lithium has surged, necessitating advanced lithium extraction technologies. Electrochemical methods, noted for their high selectivity and efficiency in extracting target ions from liquid sources in an environmentally friendly manner, have become increasingly vital. These methods are versatile, applicable in scenarios such as lithium extraction from saline lakes, mother liquor separation, and lithium enrichment. They include electrochemical deintercalation, electrochemical ion pumps, and electrodialysis, each offering unique benefits and challenges depending on the application context. This review provides a detailed exploration of the research progress in lithium extraction using electrochemical methods and discusses future prospects for these technologies, emphasizing their potential to meet the growing demand for lithium.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

The leather industry is one of the most polluting industries in the world due to the large amounts of waste following the raw hides processing, but also due to the high content of chemicals present in their composition. The main problem of chromium-tanned leather solid waste is related to their storage, because of the ability of chromium to leach in soil or water, and also owing to the high ability of trivalent chromium to oxidize to its toxic form, hexavalent chromium. The purpose of this study is to present the latest methods for extracting trivalent chromium from the composition of solid leather wastes. The extraction methods identified in the present study are based on acid/basic/enzymatic hydrolysis and substitution with the help of organic chelators (organic acids and organic acid salts). In addition, the study includes a comparative analysis between the advantages and disadvantages of each identified extraction method. At the same time, the study also presentes alternative chromium extraction methods based on the combination of conventional extraction methods and ultrasound-assisted extraction.

The medicinal herb Centaurium erythraea is well-known for its natural ability to treat digestive issues like dyspepsia and liver insufficiency by promoting the secretions of the liver and esophagus. This study aimed to analyze the effectiveness of Centaurium erythraea extracts in treating diabetes. Decoction and Soxhlet procedures were used to examine the extracts, with water serving as the solvent. The extracts were tested for antioxidant capacity, antimicrobial effects, and inhibitory effects on alpha-amylase activity. In comparison to the aqueous extract, the decocted extract had higher levels of polyphenols, total tannins, and anthocyanins, as well as more effective antioxidant capacities. Due to its reduction of alpha-amylase activity and enteric absorption of glucose, Centaurium erythraea has also shown considerable anti-hyperglycemic action.

Dried blood spot (DBS) testing on confetti is one of the most common methods used to collect and extract DNA from field samples for molecular epidemiology of malaria studies. Here, we investigated whether ethanol or other solutions used to clean scissors are a source of sample contamination. DBS were prepared from 3 drops of blood from two Plasmodium falciparum cultures spotted on confetti, and 3 solutions (water, ethanol and DNase) were used to clean scissors between spots during DNA extraction. For each cleaning solution, two blank confetti were used as negative controls. Samples were analyzed by PCR-based genotyping of merozoite surface proteins 1 & 2 (msp-1 and msp-2), and P. falciparum chloroquine resistance transporter (Pfcrt). A total of 15 samples were analyzed. Based on msp-1 and msp-2 amplification, P. falciparum was detected on blank confetti when scissors were washed with ethanol. Based on Pfcrt amplification, DNA of P. falciparum was detected on blank confetti when scissors were cleaned with ethanol or water. No P. falciparum genes were detected on blank confetti when scissors were cleaned with DNase. Scissors cleaned with DNase prevented cross-contamination between samples during processing of dried blood spots, whereas ethanol (which is commonly used) fails to avert cross-contamination.

The present paper reports an alternative solution of the measurement problem in quantum theory. The measurement problem can be characterized as that the U-procedure verses the R-procedure. The R-procedure is tested by the Yes/No measurement originally proposed by von Neuman and discussed in details by Penrose. We propose a novel stochastic sampling method to tackle the measurement paradox. Each testing sample produces a pair of Yes-number c and No-number d, which in turn generates a sample phase with respect to the exponential form of (c+id). All the sample phases forms a group G_R. Taking G_R as the sampling potential, combined with the dynamic phase group G_U，we establish a unified model of U-procedure and R-procedure for the evolution of wavefunction. Based on the Born rule, the probability of a sample is given by the squared magnitude of （c+id）. Some metaproperties of the new U-R model, such as natural transformation, consistency, and completeness, are presented. The present work provides a new picture of quantum mechanics and alike. The measurement problem widely exists in dynamic analysis, higher cognition, and large data modeling. Thus, the work reported here has a wide range of applications. Keywords: The measurement problem; U-R procedures; the Yes/No type measurement; stochastic sampling; sample phase; Born probability.

This research introduces a hybrid feature extraction approach that combines Linear Discriminant Analysis (LDA) and Multilayer Perceptron (MLP) methods to address the challenges of reducing feature vector dimensionality and accurately classifying smartphone-based human activities. Moreover, to refine activity classification accuracy, Support Vector Machine (SVM) optimization with Stochastic Gradient Descent (SGD) is employed. LDA, a statistical tool, is leveraged to derive a new feature space for data projection, enhancing class separation and test feature label prediction. The proposed approach, named LMSS, was evaluated using the UCI-HAR dataset and compared with state-of-the-art models. The results demonstrate that the proposed approach outperformed the best-performing method over this dataset. It achieved an accuracy rate of 99.52%, precision of 99.55%, recall of 99.53%, and an F1-score of 99.54%, highlighting the effectiveness of the proposed method in accurately classifying the data.

Nowadays circular economy trend drives researchers in the recovery of various bioactive compounds from agri-food by-products. Enzyme-assisted extraction (EAE) is shown as an innovative green technology for the effective extraction of various phytochemicals from agri-food section by-products, therefore this study aimed to evaluate the application of EAE as green technology to obtain extracts from olive leaves (Olea europaea) for potential industrial production. EAE was conducted under various enzyme dose combinations, and incubation time (120 min). Obtained extracts were characterized in terms of total polyphenols (TP) and Total Antioxidant Activity (AA). Firstly, the enzyme synergistic effect in enzymatic extraction of polyphenols was evaluated. TP optimal extraction conditions (468.19 mg GAE/L) were achieved after EAE (50-50%) and for AA (69.85 AA%). According to the above results, a second experimental part occurred for the incubation time (min.) and enzyme dose (mL) of optimal extraction conditions of olive leaves. Results indicated EAE as an excellent choice for green extraction of polyphenols from the olive leaves.

The question whether a given set of test items can be considered “identical” is often addressed in terms of the homogeneity of the test material from which said items were taken. However, for some types of matrices – in particular, for matrices consisting of minute separate particles, only some of which carry the analyte under consideration – even in the case of homogenous test material, an irreducible source of variability between test items may remain: the fundamental variability. In this paper, the concept of fundamental variability is explained, and procedures for reducing and characterizing it are described.

Divergences have become a very useful tool for measuring similarity (or dissimilarity) between probability distributions. Depending on the field of application a more appropriate measure may be necessary. In this paper we introduce a family of divergences we call gamma-divergences. They are based on the convexity property of the functions that generate them. We demonstrate that these divergences verify all the usually required properties, and we extend them to weighted probability distribution. We investigate their properties in the context of kernel theory. Finally, we apply our findings to the analysis of simulated and real time series.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Extraction techniques of important bioactive molecules from the major concern of Seafood byproducts are getting emphasis for better valorization. Employing green extraction technologies for efficient and quality production of these bioactive molecules is also strictly required. Hence, understanding the extraction process parameters to effectively design an applicable optimization strategy could make this real. In this review, statistical optimization strategies applied for the extraction process parameters of bioactive molecules from Seafood byproducts are focused. The type of experimental designs, and techniques applied to criticize and validate the effects of independent variables on the extraction output was addressed. Dominant parameters studied were enzyme/substrate ratio, pH, time, temperature and power of extraction instruments. The yield of bioactive compounds, chitin and chitosan, proteins and peptides, enzymes and carotenoids (Astaxanthins) were the most studied responses. Efficiency and/or economic and quality considerations and their selected optimization strategies that favour the production of potential bioactive molecules were also reviewed.

This study explores the complexities involved in the extraction and purification of catechins, prominent bioactive compounds found in plant extracts and tea. It addresses challenges arising from the intricate molecular structure of catechins and their inherent variability across botanical sources. Despite these obstacles, catechins present significant potential, particularly in healthcare. Their potent antioxidant properties have been extensively investigated and associated with numerous health benefits, positioning them as promising therapeutic agents for combating chronic diseases. Furthermore, catechins have diverse applications across various industries, including food and beverage, cosmetics, agriculture, and materials science. This abstract emphasizes the importance of continued research and innovation in catechin extraction and utilization, which hold promise for advancing human health and technological progress across multiple domains.

Although the behavioral mechanism studying is a difficult and complex task, it can produce an important systems optimization impact. In this work, we use, in this paper, inference system approach to represent reasoning mechanism and the operations of dynamic systems to extract mental representations from traveling salesman and convert them into cognitive structures. For this we develop an extraction automatic method to create knowledge bases and, later, data are stocked into structure based on transition maps and the performances of these created maps get improved through combining the reinforcement learning thus augment traveller's deciding capacity from historical data. These transition maps help to find best actions for obtaining useful new policies. Generated intermediate transition maps are gathered to give a global map called main map whose advantage is to improve the learning process. The main idea of this approach is to improve learning capability by using a reinforcement learning technique as exploration and exploitation strategy of the metaheuristique GRASP method and the use of the fuzze logical rules mechanism allowing concepts model to have more variability of states. The results obtained after simulation as presented in this paper are very encouraging.

: This article was not intended to be a complete report of a standard clinical trial. It is a report of the outcomes of preliminary data for validation of the CMECD procedure (Coletti Method of EMG ChemoDenervation) protocol for the treatment of chronic pain resulting from chronic muscle spasm. Methods are here detailed on how to approach the patient with chronic pain, identify the presence of chronic muscle spasm, undertake the treatment protocol and how to perform the follow up process to confirm that chronic pain secondary to chronic muscle spasm was the accurate diagnosis. Furthermore, this article presents the results of a cohort of more than 90 patients treated by the CMECD procedure regarding location and duration of prior pain, prior treatment strategies, degree of success in resolving pain and duration of relief. Outcome data consisting of patient and staff reporting of specific situations in which the chronic pain treatment was successful has been included to help establish the “believability” of outcome successes and to elucidate the potential life altering effects of successful treatment of chronic pain secondary to chronic muscle spasm. This article will hopefully increase the interest in this treatment protocol and increase the chance that a classical international clinical trial will be undertaken.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

Fatigue performance and self-repairing activity of asphalt binders are two properties that highly influence the fatigue cracking response of asphalt pavement. There are still numerous gaps of knowledge to fill linked with these two characteristics. For instance, current parameters fail to fully accommodate these two bitumen phenomena. This study aims to propose a new procedure to address this issue utilizing the linear amplitude sweep (LAS) test, LAS with rest period (RP) (LASH) test, and simplified viscoelastic continuum damage (S-VECD) model. This research work used four different types of asphalt binders: neat asphalt (NA), self-healing thermoplastic polyurethane (STPU)-modified bitumen (STPB), self-healing poly (dimethyl siloxane) crosslinked with urea bond (IPA1w)-modified bitumen (IPAB), and styrene–butadiene–styrene (SBS)-modified bitumen (SBSB). Before the testing process, all the materials were subjected to short-term and long-term aging. The new procedure showed a superior capacity to analyze and accommodate all bitumen fatigue performances and self-repairing activities compared to the current method. Another finding proved that asphalt binders with higher self-restoration behavior failed to show better fatigue performance. A breakthrough finding demonstrated that asphalt binder fatigue response augmented when the RP was applied at a higher damage intensity (S) value. STPBs and IPABs reached their highest increments of fatigue response, containing 1.0% of STPU and 0.5% of IPA1w, respectively. Those augmentations were 207.54% and 232.64%, respectively.

This paper presents three approaches to estimating battery parameters of the electrical equivalent circuit model (ECM) based on electrochemical impedance spectroscopy (EIS); these approaches are referred to as (a) least squares (LS), (b) exhaustive search (ES), and (c) nonlinear least squares (NLS). The ES approach is assisted with the LS method for the rough determination of the lower and upper bound of the ECM parameters, and the NLS approach is incorporated with the Monte Carlo run such that different initial guesses can be assigned to improve the goodness of EIS fitting. The proposed approaches are validated using both simulated and real EIS data. Compared to LS approach, the ES and NLS approaches show better fitting accuracy at various noise levels; whereas both in the validation using simulated EIS data and actual EIS data collected from LG 18650 and Molicel 21700 batteries, the NLS approach shows better fitting accuracy than that of LS and ES approaches. In all cases, compared with the ES approach, the computational time of the NLS approach is significantly faster, and compared with the LS approach, the NLS approach shows a minimal difference in computational time and considerably better fitting performance.

Historic expeditions are events that are flavored by exploratory, scientific, military or geographic characteristics. Such events are often documented in literature, journey notes or personal diaries. A typical historic expedition involves multiple site visits and their descriptions contain spatiotemporal and attributive contexts. Expeditions involve movements in space that can be represented by triplet features (location, time and description). However, such features are implicit and innate parts of textual documents. Extracting the geospatial information from these documents requires understanding the contextualized entities in the text. To this end, we developed a semi-automated framework that has multiple Information Retrieval and Natural Language Processing components to extract the spatiotemporal information from a two-volumes historic expedition gazetteer. Our framework has three basic components, namely, the Text Preprocessor, the Gazetteer Processing Machine and the JAPE (Java Annotation Pattern Engine) Transducer. We used the Brazilian Ornithological Gazetteer as an experimental dataset and extracted the spatial and temporal entities from entries that refer to three expeditioners’ site visits and mapped the trajectory of each expedition using the extracted information. Finally, one of the mapped trajectories was manually compared with a historical reference map of that expedition to assess the reliability of our framework. The reference map was manually prepared in previous research work by others.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Technological equipment in quarries that extract and deliver aggregates for different uses operates in a predetermined flow depending on the type of rocks exploited and the dimensional characteristics imposed on the final products. In this context, the interruptions in operation required to replace high-wear parts (such as the teeth of excavators and bucket loaders) must be limited as much as possible through technological solutions to increase their service life. The evolution of the wear of the teeth of the quarry equipment that come into direct contact with the rocks was concretely established in the production process, in parallel with the wear values obtained by simulating the wear phenomenon in laboratory conditions, in order to validate the data collected during the operation of the machines. Preventive-repetitive maintenance, within the activities of reconditioning the worn surfaces of the teeth, through the charging process by manual electric welding with covered electrodes, was applied directly to the machine, which led to the shortening of the interruptions in operation necessary to replace these spare parts.

On the eve of the Brexit process, in the context of a rising Euroscepticism that fuels the modest confidence of European citizens in their national and European institutions, the article assesses the efficiency and effectiveness of the European Parliament within the framework of the ordinary legislative procedure (co-decision). After defining and formulating the main indicators, the paper analyses the micro- and macro-performance of the European Parliament within the decision-making process from a quantitative-qualitative and a qualitative-quantitative perspective, highlighting the relativizing factors and the responsiveness of the European decision-making process to the Europeans’ needs.

Cannabis is a flowering plant that has long been used for medicinal, therapeutic, and recreational purposes. Cannabis contains more than 500 different compounds, including a unique class of terpeno-phenolic compounds known as cannabinoids; Δ9-tetrahydrocannabinol (THC) and cannabidiol (CBD) are the most prevalent cannabinoids and have been associated with the therapeutic and medicinal properties of the cannabis plant. In this paper, continuous flow microwave assisted extraction (MAE) is presented and compared with other methods for commercial cannabis extraction. The practical issues of each extraction method are discussed. The main advantages of MAE are: continuous-flow method which allows for higher volumes of biomass to be processed in less time than existing extraction methods, improved extraction efficiency leading to increased final product yields, improved extract consistency and quality because the process does not require stopping and restarting material flows, and ease of scale-up to industrial scale without the use of pressurised batch vessels. Moreover, due to the flexibility of changing the operation conditions, MAE eliminates additional steps required in most extraction methods, such as biomass decarboxylation, winterisation, which typically adds at least a half day to the extraction process. Another factor that sets MAE apart is the ability to achieve high extraction efficiency even at the industrial scale. Whereas the typical recovery of active compounds using supercritical CO¬2 remains around 70-80%, via MAE up to 95% of the active compounds from cannabis biomass can be recovered at the industrial scale.

The joint extraction of entities and relations is a critical task in information extraction, and its performance directly affects the performance of downstream tasks. However, existing joint extraction models based on deep learning exhibit weak processing capabilities for the phenomenon of multiple pronunciations of one character and multiple characters of one pronunciation when processing Chinese texts, resulting in performance loss. To address these issues, this paper introduces part-of-speech (POS) and pinyin features to aid the model in learning semantic features that are more contextually appropriate. A Chinese Joint Entity and Relation Extraction Model based on Progressive Contrastive Learning and Heterogeneous Feature Fusion is proposed (CJE-PCHF). During model training, an interactive fusion network based on progressive contrastive learning is employed to learn the dependencies between pinyin, POS, and semantic features. This guides the model in heterogeneous feature fusion, capturing higher-order semantic associations between heterogeneous features. On the commonly used DuIE evaluation dataset for joint extraction, this model achieved a significant improvement, with the F1 score increasing by 5.4% compared to the benchmark model CasRel.

Although several protocols for genetic transformation of citrus have been published, it is highly desirable to further improve its efficiency. Here we report treatments of Agrobacterium cells and citrus explants prior to and during co-cultivation process to enhance transformation efficiency using a commercially used rootstock 'Carrizo' Citrange as a model plant. We pre-cultured Agrobacterium cells in a 1/10 MS, 0.5 g/L 2-(N-morpholino) ethanesulfonic acid (MES) and 100 µM acetosyringone liquid medium for 6 hours at 25 ℃ before used to infect citrus explants. We incubated epicotyl segments in an MS liquid medium containing 13.2 µM 6-BA, 4.5 µM 2,4-D, 0.5 µM NAA for 3 hours at 25℃ prior to Agrobacterium infection. In the co-cultivation medium, we added 30 µM paclobutrazol and 10 µM lipoic acid. Each of these three treatments significantly increased the efficiencies of transformation. When the three treatments were combined, we observed that the transformation efficiency was enhanced from 11.5% to 52.3%. The improvement of genetic transformation efficiency mediated by these three simple treatments may facilitate more efficient applications of transgenic and gene editing technologies for functional characterization of citrus genes and for genetic improvement of cultivated citrus varieties.

A paper impregnated with silver nanoparticles (AgNPs) has been prepared. For the preparation of the substrates, aqueous suspensions of pulp fines, a side product from the paper production, have been mixed with Ag nanoparticles (AgNP) suspensions. The nanoparticle synthesis thereof was carried out via laser ablation of pure Ag in water. After the sheet formation process, the leaching of the AgNPs was determined to be low while the sheets exhibited antimicrobial activity towards E. Coli.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

Demand for nutmeg essential oil in Indonesia and the world is increasing. Nutmeg essential oil is obtained from young nutmeg seeds extracted by water steam distillation (WSD). The weakness of the extraction process with WSD is the long distillation time (24 hours), wasteful of fuel, wasteful of manpower, produces polluting gases which damage the environment and requires a lot of water as a coolant. The purpose of this study was to compare the WSD and SCFE methods for extracting nutmeg essential oil. The research was conducted by extracting nutmeg essential oil using two methods are WSD and SCFE. The results showed that the chemical composition of the nutmeg essential oil produced by the two methods was almost similar. Nutmeg essential oil produced by both methods shows the same characterization. The yield between the two methods is almost the same, in the range of 10-12% using extraction time 15-60 minutes. The SCFE method has advantages over WSD are a faster extraction time, does not require heating materials and CO2 gas can be reused. In conclusion, SCFE is an alternative method to increase the production of nutmeg oil.

This paper studies the pilot control strategy and workload of tilt-rotor aircraft dynamic conversion procedure between helicopter mode and fixed-wing mode. A nonlinear flight dynamics model of tilt-rotor aircraft with full flight modes is established. On this basis, a nonlinear optimal control model of dynamic conversion is constructed, considering factors such as conversion corridor limitations, pilot control, flight attitude, engine rated power, and wing stall effects. To assess pilot workload, an analytical method based on wavelet transform is proposed, which examines the mapping relationship between pilot control input's amplitude, constituent frequencies, and control tasks. By integrating the nonlinear optimal control model and the pilot workload evaluation method, the analysis of pilot control strategy and workload during the conversion procedure is conducted, leading to the identification of strategies to reduce pilot workload. The results indicate that incorporating the item of pilot workload in the performance index results in a notable reduction in the magnitude of collective stick inputs and longitudinal stick inputs. Moreover, it facilitates smoother adjustments in altitude and pitch attitude. Additionally, the conversion of the engine nacelle can be achieved at a lower and constant angular velocity. In summary, the conversion and reconversion procedures are estimated to have a low workload (Level 1 ~ Level 2), with relatively simple and easy manipulation for the pilot.

Cyclic voltammetry can be applied as the reliable method for the determination of chloride ions in a range from several to couple hundred ppm. Since the standard potential of chloride ion/gaseous chlorine is 1.36 V vs NHE the efficient oxidation of Cl- ion occurs at very positive electrode potentials, usually higher than + 1.7 V vs NHE electrode. It is possible to observe this phenomenon only at noble-metal or inert carbon electrodes. Many other solutes, usually organic compounds, are often oxidized at this potential. This is the reason why determination of Cl- content directly from increase of the oxidation current is not reliable and can lead to overestimated values. However, gaseous chlorine, generated at positive potential dissolves in the analyzed solution and can be reduced in the reverse scan of cyclic voltammetric curve. Optimization of the experimental procedure using the statistical tools allowed for the development of the improved method for the direct quantification of chloride ions in acid copper electroplating baths. Under the proposed experimental conditions, the calibration curve (Cl2 voltammetric reduction current vs. chloride ions concentration) is represented by the linear model for the concentration of chlorides ranging from 10 to 200 mg/dm3.

The bond index is an indicator of the grindability of the material and is widely used in the preparation of mineral raw materials and the cement industry. Paper offers new, abbreviated and simplified procedure to determine Bond work index that relies on first-order kinetics law and can be performed with any number of grinding cycles, depending on the desired accuracy of the required data. The parameters G and P80 of each grinding cycle are multiplied by the newly founded coefficients giDT and piDT to obtain values approximately equal to these parameters of the last grinding cycle when the equilibrium state is reached in the standard test. The paper presents comparative results obtained by standard Bond and new shortened procedure on individual samples of andesite, limestone, copper-ore and smelter slag and on composite samples of andesite from limestone and copper-ore with smelter slag in different mass ratios. As the number of grinding cycles increases, the precision of the shortened procedure increases, and the mean square error decrease 3.59%, 2.61% and 1.74% for two, three and four grinding cycles.

Winding design methods have been a subject of research for many years of the past century. Many methods have been developed, each one characterized by some advantages and some drawbacks. Nowadays, the star of slots is the most widespread design tool for electrical machine windings. In this context, this paper presents a simple and effective procedure to determine the distribution of the EMF stars and of the winding configuration in all possible typologies of electrical machines equipped with symmetrical windings. Moreover, this procedure can also be easily implemented in a computer program in order to perform automated winding designs for rotating electrical machines. Several examples are provided in order to validate the proposed procedure.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

The number of documents published on the Web other languages than English grows every year. As a consequence, it increases the necessity of extracting useful information from different languages, pointing out the importance of researching Open Information Extraction (OIE) techniques. Different OIE methods have been dealing with features from a unique language. On the other hand, few approaches tackle multilingual aspects. In such approaches, multilingual is only treated as an extraction method, which results in low precision due to the use of general rules. Multilingual methods have been applied to a vast amount of problems in Natural Language Processing achieving satisfactory results and demonstrating that knowledge acquisition for a language can be transferred to other languages to improve the quality of the facts extracted. We state that a multilingual approach can enhance OIE methods, being ideal to evaluate and compare OIE systems, and as a consequence, to applying it to the collected facts. In this work, we discuss how the transfer knowledge between languages can increase the acquisition from multilingual approaches. We provide a roadmap of the Multilingual Open IE area concerning the state of the art studies. Additionally, we evaluate the transfer of knowledge to improve the quality of the facts extracted in each language. Moreover, we discuss the importance of a parallel corpus to evaluate and compare multilingual systems.

This study aimed to evaluate the effect of convective and microwave drying on the content of bioactive compounds of blackberry (Rubus fruticosus), drying parameters and energy consumption. The fruit was dehydrated in a convective dehydrator at a temperature of 50 °C and 70 °C and a microwave oven at power levels of 90 V, 180 V and 240 V. The highest amount of anthocyanins, polyphenols and antioxidant capacity were obtained in microwave dried blackberry fruits at 90 V and 180 V. It turned out that microwave dehydration shortened the processing time and lower the energy consumption compared to the convective drying. Blackberry fruits dehydrated at 240 V showed the shortest dehydration time, minimal energy consumption and the most efficient diffusion.

Extracting the economic value by integrated utilization of space in old communities is crucial for encouraging independent participation from enterprises and residents, reducing reliance on government leadership and fiscal investment. This study starts from the active perspective of spatial assets, constructs a value activation framework for old community spatial assets by balancing "endogenous demand" and "exogenous opportunities." By enhancing "economic value" through "use value," five methods for value extraction and overall project utilization paths are proposed, guided by a dynamic "cost-revenue" balance. Using multi-source data, we identify the spatial assets of 1,096 old communities in central Guangzhou and apply a market comparison method for economic value assessment. Additionally, the study offers recommendations on timing and project portfolios for regeneration efforts, along with strategies for establishing a coordinating implementation entity and fund account. This research provides strategic insights for advancing the regeneration of old communities by tapping into their macro-level economic potential.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

The proliferation of intelligent monitoring devices has led to the widespread adoption of background extraction technology across a multitude of domains, including intelligent transportation, video surveillance, human-computer interaction, and medical diagnosis. In this work, the model employs a multi-layer convolutional neural network structure, which enables the extraction and fusion of scene features from different scales in a layer-by-layer manner. This approach facilitates the comprehensive capture of complex scene information. The convolutional network comprises multiple layers, with each layer responsible for extracting features at a specific scale. The shallower layers capture more detailed feature information, whereas the deeper layers focus on more global scene features. The strategy of multi-scale feature fusion allows the model to fully capture multi-level and multi-dimensional information in the context of large-scale scenes. Furthermore, the incorporation of an attention mechanism enables the model to adaptively allocate attention to salient regions, thereby enhancing its capacity to discern intricate scenes by assigning greater significance to pivotal features. The experimental results demonstrate that the proposed method is effective in practice, as evidenced by its performance on public datasets.

Ranunculus asiaticus L. is an ornamental geophyte, mainly propagated by rehydrated tuberous roots. Vernalization before planting is a common practice to overcome the natural dormancy of tuberous roots, however little is known about the mechanisms underlying the plant response to low temperature. We investigated the influence of two hybrids, MBO and MDR, and three preparation procedures of tuberous roots, only rehydration (control, C), and rehydration plus vernalization at 3.5 °C for 2 weeks (V2) and for 4 weeks (V4), on plant growth, leaf photosynthesis, flowering and metabolism in plants grown in pot in unheated greenhouse. We reported the responses observed in the aerial part previously in this journal (Fusco et al., 2023). In this paper, we show changes in carbohydrate, amino acids, polyphenols and protein levels throughout the growing cycle, in the different plant stages: pre-planting, vegetative phase and flowering.

Patients in intensive care unit often lose a considerable fraction of their gut microbiome due to exposure of broad-spectrum antibiotics and other reasons. Dysbiosis often results in prolonged diarrhea and increase occurrence of multi-drug resistant pathogens in the colon with clinical consequences not yet well understood. Restoring the microbioma by faecal microbial transplantation (FMT) is a plausible therapeutic possibility, so far only documented in case reports and case series using very heterogeneous methodologies. Before FMT in critically ill can be tested in randomised controlled trials, there is a burning need to describe a standardized operating procedure (SOP) of the whole process, respecting the specifics of critically ill population, such as the risk of disrubted intestinal barrier and time critical nature of the procedure. We describe the SOP that has been developed for experimental use in critically ill patients by a multidisciplinary team of intensivists, gastroenterologist and microbiologist based on feedback from regulatory authority (State Institue of Drug Control of the Czech Republic). The hallmarks of these SOPs are multi-donor freshly frozen transplantate quaranteeded for 3 months consisting of 7 aliqutes from 7 unrelated healthy donors, and administered by rectal tube. In this paper we discuss the rationale for this SOP and the process of its development in details and release the full proposed SOP is in the form of online appendix.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

Adhesion systems are very important in robots for infrastructure inspection (especially in vertical walls). They present the challenge of optimizing the ratio vacuum/power consumption in battery-powered robots. In this paper a CFD (Computer Fluid Dynamics) modelling and optimization process of a robot adhesion system is carried out to determine the best performing configuration in terms of vacuum and power consumption. Analytical and numerical models were developed to predict the behaviour of the system for different configurations. The models were validated, using test rig measurements, by calibrating an arbitrary defined inlet height that simulates the leakage flow. Then, different geometric parameters were varied to determine the best performing configuration based on the vacuum/power consumption ratio value. The model presented in the paper was capable of predicting the behaviour of the system for different configurations, with a margin of error of 15% for the vacuum prediction and a 25% for the motor power calculation. Finally, the model was used to optimize parameters of the system, like the number of blades of the impeller. The adhesion system was conceived for the modular autonomous climbing legged robot ROMERIN.

Afterthe series of earthquakes in August 1953, most of Kefalonia’s building stock totally collapsed. The buildings that emerged as a result of a collective effort are commonly referred to as «arogi» buildings, with the term arogimeaning help or assistance. In this way, merely referring to these structures is a direct mention to the circumstances under which they were constructed. The reconstruction of the building stock of the island was based in a series of building types proposed from the authorities, and proceeded replacing the richness of the architectural forms that stood before the earthquake, with austere but necessary settlements. Nevertheless, it is these buildings that constitute today’s image of the island. This study wishes to introduce us to “arogi” buildings structural system, as it was applied in Kefalonia after 1953 earthquake, with reference to recent bibliography and the recent experience of 2014 earthquake. The purpose of setting the grounds for such a research would be to highlight the effectiveness of this structural system. Moreover, to emphasize the fact that “arogi” buildings and their construction procedure incorporate Kefalonia’s recent history and have eventually produced today’s available “traditional” architecture of the island.

Despite offering several potential benefits over standard prosthetic aortic valve replacement, the use of the pulmonary autograft has been limited to date, due to concerns over the risk of pulmonary autograft expansion and the need for reintervention. Several techniques using materials with biomimetic potential have been developed to reduce this complication. The incidence, risk factors and pathophysiology of pulmonary autograft dilatation are discussed in this article. This seminar will provide an overview of the techniques of external pulmonary autograft support and their advantages and limitations. It also considers future directions for further investigation and future clinical applications of external pulmonary autograft support. Dilatation of the autograft is more likely to occur in patients with aortic regurgitation and a dilated aortic annulus. External scaffolding may prevent autograft stretching and expansion in these specific cases. However, from a biomimetic point of view, any permanent scaffold potentially restricts the movement of the autograft root. This reduces some of the benefits associated with the use of autologous tissue, which is the priority of the Ross procedure. To address this issue, several bioresorbable matrix could be used to support the root during its initial adaptive phase. Control of blood pressure with aggressive therapy is the first line to avoid this problem in the first year after pulmonary autograft implantation, together with support of the annular and sino-tubular junction in some selected cases. This is the best way to maintain stable autograft root dimensions while preserving root dynamics. However, to determine the efficacy of this combined external support and best medical management, it is important to perform regular imaging and clinical follow-up.

A new formulation for a proposed solution to the 3D Navier-Stokes Equations in cylindrical co-ordinates coupled to the continuity and level set convection equation is presented in terms of an additive solution of the three principle directions in the radial, azimuthal and z directions of flow and a connection between the level set function and composite velocity vector for the additive solution is shown. For the case of a vertical tube configuration with small inclination angle, results are obtained for the level set function defining the interface in both the radial and azimuthal directions. It is found that the curvature dependent part of the problem alone induces sinusoidal azimuthal interfacial waves wheras when the curvature together with the equation for the composite velocity is considered oscillating radial interfacial waves occur. The implications of two extremes indicate the importance of looking at the full equations including curvature.

Countless disasters have resulted from climate change, causing severe damage to infrastructure and the economy. These disasters have significant societal impacts, necessitating mental health services for the millions affected. To prepare for and respond effectively to such events, it is crucial to understand people's emotions and the life incidents they experience both before and after a disaster strikes. In this case study, we mined the emotions and life incidents expressed on Twitter during the 2017 Hurricane Harvey. Between August 20 and August 30, we collected a dataset of approximately 400,000 public tweets related to the storm. Using a BERT-based model, we predicted the emotions associated with each tweet. Following emotion prediction, we applied various natural language processing techniques to analyze the content of the tweets, aiming to uncover the 'topics' discussed alongside specific 'emotions.' To efficiently identify these topics, we utilized the Latent Dirichlet Allocation (LDA) technique for topic modeling, which allowed us to bypass manual content analysis and extract meaningful patterns from the data. However, rather than stopping at topic identification, we further refined our analysis by integrating Graph Neural Networks (GNN) and Large Language Models (LLM). The GNN was employed to generate embeddings and construct a similarity graph of the tweets, which was then used to optimize clustering. This step ensured that related tweets were accurately grouped together based on their content and context. Subsequently, we used an LLM to automatically generate descriptive names for each event cluster. This advanced approach allowed us to identify and label life incidents automatically, providing a nuanced understanding of the key issues faced by the community during the hurricane. The results revealed significant emotional shifts as the hurricane reached its most devastating phase. These shifts coincided with pressing concerns and demands from the population, such as evacuation plans, animal safety, safety updates, public policy, help requests, flood impacts, and the spread of fake news. By combining GNN and LLM for automatic event name prediction, our study not only mapped out the emotions but also accurately categorized the specific life incidents that were most relevant during the disaster, offering critical insights for disaster preparedness and response strategies.

More than 700 anthocyanins are described so far, and many different sources are rich in these natural pigments. During the last few years, researchers have been focusing of strategies to recover and purify anthocyanins, from simple liquid-liquid extractions to more advanced supercritical CO2 extractions, however, with such a huge number of different sources, it’s extremely hard to get a simple and fast methodology that fits several sources, not only by the structural nature of the anthocyanins but also by the presence of specific groups of natural compounds. Using simple methodologies like solid-phase extraction resins represents a powerful economical and efficiency strategy. In this work, we tested several sources of structurally distinct anthocyanins, including purple basil, purple cabbage, purple sweet potato, butterfly pea flower, cornflower and wild pansy, in different resins to assess their efficiency in the obtention of anthocyanin-pure extracts. The results showed us that the combination of oasis HLB® resin followed by a cation-exchange SPE with DSC-MCAX® resulted in high-purity anthocyanin extracts for all the cases.

Salvia miltiorrhiza (SM) contains the tanshinones, a compound with various pharmacological effects, and has been extensively studied as a pharmaceutical material. However, conventional methods for extracting tanshinones face challenges such as environmental hazards and high cost. In this study, we aimed to effectively extract tanshinones from SM using cloud point extraction (CPE) with lecithin, a natural surfactant. By optimizing various extraction conditions including the solid-to-liquid ratio, lecithin concentration, NaCl concentration, pH, and equilibrium temperature, the optimal extraction efficiency was achieved using 20 mL of solvent per 1 g of sample, 3% lecithin (w/v), 2% NaCl (w/v), pH 6, and room temperature (25 ± 2°C). The CPE method, which minimizes the use of organic solvent and is eco-friendly demonstrated improvements in extraction efficiency, with a 4.55% increased for dihydrotanshinone I, 8.32% for cryptotanshinone, 15.77% for tanshinone I, and 6.81% for tanshinone IIA compared to the conventional water extraction method. These results suggest that CPE is promising, environmentally friendly, and efficient approach for extracting hydrophobic components from pharmacologically active materials such as SM, with potential applications across various fields of natural product extraction.

Cyanex 301 and LIX 63 can seletively extract Pd(II) over Pt(IV) from strong hydrochloric acid solutions. Therefore, solvent extraction experiments have been performed by extractant mixtures containing either Cyanex 301 or LIX 63 and the extraction behavior of Pd(II) was compared. Among the mixture of Cyanex 301, the highest synergistic enhancement coefficient was achieved by mixing Cyanex 301 and TOPO. However, it was very diffiuclt to strip the Pd(II) from the loaded mixture. Among the mixture of LIX 63, the mixture of LIX 63 and Alamine 336/TOPO enhanced the extraction of Pt(II). Although the synergistic coefficient by Cyanex 301 + TOPO was higher than that by LIX 63 + Alamine 336, the Pd(II) in the loaded mixture of LIX 63 and Alamine 336 was easily stripped by thiourea.

Natural carotenoids are secondary metabolites that exhibit antioxidant, anti-inflammatory and anti-cancer properties. These types of compounds are in high demand by pharmaceutical, cosmetic, textile and food industries, leading to the search for new natural sources of carotenoids. In recent years, the production of carotenoids from bacteria has become of great interest for industrial applications. In addition to carotenoids with C40-skeletons, some bacteria have the ability to synthesize characteristic carotenoids with C30-skeletons. In this regard, a great variety of methodologies for the extraction and identification of bacterial carotenoids has been reported and this is the first review that condenses much of this information. To understand the diversity of these carotenoids, we present their biosynthetic origin in order to focus on the methodologies employed in their extraction and characterization. Special emphasis has been made on high-performance liquid chromatography-mass spectrometry (HPLC-MS) for the analysis and identification of bacterial carotenoids. We end up this review showing their potential commercial use of bacterial carotenoids. This review is proposed as a guide for the identification of these metabolites, which are frequently reported in new bacteria strains.

A study has been carried out on Ta and Nb recovery by liquid-liquid extraction process using 4-methylacetophenone (4-MAcPh) as organic phase. The 4-MAcPh was compared to methylisobutylketone (MIBK) with respect to extraction efficiencies (kD values) at different concentrations of H2SO4 in the aqueous phase. The results showed a similar extraction of Nb for both solvents. However, for Ta extraction efficiency is increased by a factor of 1.3 for 4-MAcPh. In addition, the MIBK solubilized completely after 6 mol L-1 of H2SO4 against only a loss of 0.14 to 4% for 4-MAcPh between 6 and 9 mol L-1 of H2SO4. The potential of 4-MAcPh has also been studied to selectively recover Ta from a model capacitor waste solution. The results showed a selectivity for Ta in the presence of impurities such as Fe, Ni, Mn. The 4-MAcPh also presents the advantage of having physicochemical properties adapted to its use in liquid-liquid extraction technologies such as mixer-settlers.

This paper provides orthogonal moments (OM) such as, Zernike Moments(ZM), Psuedo Zernike Moments(PZM) and Orthogonal Fourier Mellin Moments(OFMM) for the analysis of melanoma images. The moment invariants may vary with respect to geometric variations. For the analysis of orthogonal moments hundred random melanoma images and hundred non-melanoma images have been taken into consideration from the database of 570 melanoma images and 250 non-melanoma images respectively. Orthoganal moments have been computed by varying the phase angles from 10° to 40° with an equal interval of 10° degree for the orders 2, 4,8,16,32,64,128,256 respectively. For the optimal OMs Particle Swarm Optimization (PSO) technique have been used. These set of extracted optimal OMs have been further applied to classify melanoma images. Support Vector Machine (SVM) has been used for the classification of [1]sensitivity=88.78%.

Sports video analysis is an interesting and emerging field in the domain of computer vision. It has become a very popular subject among scholars all over the world in the last decade due to the need of automated classification of events such as offsides, in/out situations, goals and so on. The most important problem in sports video analysis is detection and tracking of ball and players. Extraction of court lines is also another important problem since it is necessary in the classification of aforementioned events. In this study, considering some of the previous work on the subject, we develop a method for tracking the ball and players in tennis videos where the camera position and orientation is supposed fixed.

Water samples for bacterial microbiome studies undergo a biomass concentration, DNA extraction and taxonomic identification steps. Through benchmarking, we studied the applicability of Skimmed milk flocculation (SMF) for bacterial enrichment, an adapted in-house DNA extraction protocol, and six 16S rRNA databases (16S-DBs). Surface water samples from two rivers were treated with SMF and Vacuum filtration (VF) and subjected to amplicon or shotgun metagenomics. A mock community standard underwent five DNA extraction protocols, taxonomical identification with six different 16S-DBs and evaluated by the Measurement Integrity Quotient (MIQ) score. In SMF samples, the skimmed milk was metabolized by members of lactic acid bacteria or genera such as Polaromonas, Macrococcus, and Agitococcus, resulting in increased relative abundance (p < 0.5) up to 5.0 log fold change compared to VF, rendering SMF inapplicable for bacterial microbiome studies. The best performing DNA extraction protocols were FastSpin Soil, the in-house method and EurX. All 16S-DBs yielded comparable MIQ scores within each DNA extraction kit, ranging from 61-66 (ZymoBIOMICs) up to 80-82 (FastSpin). DNA extraction kits exert more bias to the composition than the 16S-DBs. This benchmarking study presented valuable insights to inform future water metagenomic study designs.

In this study, a novel and efficient method was developed for the extraction of total flavonoids from Flos Sophorae Immaturus (FSI) using ultrasound-assisted deep eutectic solvent (UAE-DES). Different DES formulations were first investigated and choline chloride/1,2-propanediol (ChCl/PD) was identified as the optimal solvent due to its highest flavonoid yield. The extraction process was optimized through single factor experiments and response surface methodology (RSM). An extraction temperature of 68 °C, a sonication time of 41 minutes, a water content of 21% and a liquid-solid ratio of 21 mL/g were identified as the optimal conditions. Under these conditions, a maximum flavonoid yield of 378.77 mg RE/g DW was achieved. The crude extract was further purified using a macroporous D-101 resin, resulting in a flavonoid extract with a purity of 83.11 ± 3.54%. The antioxidant activity of the purified extract (FSPE) was evaluated using DPPH and ABTS radical scavenging assays, showing significant antioxidant properties with IC50 values of 52.50 μg/mL and 49.47 μg/mL, respectively. The UAE-DES method developed in this study not only significantly improves the extraction yield of flavonoids from FSI, but is also in line with sustainable and environmentally friendly practices. This method offers an environmentally friendly, efficient and scalable approach for the extraction of bioactive compounds from medicinal plants and has potential applications in the food, pharmaceutical and dietary supplement industries.

This study presents a strategic approach to developing applications focused on implementing Large Language Models using the Langchain framework in Python. Three language models are highlighted: GPT-3.5 (turbo mode), LLaMA 2, and Vicuna 7B, each with their distinctive features and capabilities. The methodology used is described in detail, including data extraction from medical reports using zero-shot prompting data extraction techniques, interaction with language models, and structured storage of results. The performance of the models in data extraction is evaluated, presenting metrics such as precision, recall, and F1 score. The results demonstrate high model capability in extracting information, although areas for improvement are identified, particularly in data extraction precision. In conclusion, the efficacy of the models in extracting information from medical histories is not considerably acknowledged, with an emphasis on the importance of improving precision and increasing the volume of trained data for future research in healthcare digitalization.

The basis of modern teeth whitening systems is the use of a whitening gel, usually containing hydrogen peroxide or carbamide peroxide. The purpose of our study was to evaluate the effect of chemical and modified office teeth whitening systems on the mineral metabolism of oral fluid and to determine a safer method. The study covered 81 patients aged 22 to 35 years of both sexes with teeth color A2 and darker on the Vita Classic scale. Determination of the concentration of calcium and phosphates in the oral fluid was carried out on a spectrophotometer using ready-made Human kits. Chemical tooth whitening was performed using a gel based on 40% hydrogen peroxide. After the procedure, remineralization therapy with enamel-sealing liquid was performed for 14 days. The obtained results indicate that the most pronounced changes in the content of calcium (+74.4%, p <0.001) and рhosphates (phosphorus) (-23.07%, p <0.001) were observed when using a chemical bleaching system. After the teeth whitening procedure using a modified technique, less pronounced changes in the concentrations of calcium (+29.07, p <0.001) and phosphorus (-14%, p <0.001) were observed. The use of remineralizing agents led to a faster recovery of the initial levels of calcium and phosphates in the oral fluid. Both bleaching systems caused similar changes in the chemical composition of the oral fluid.

Perceptual and statistical evidence has underlined voice characteristics of individuals affected by genetic syndromes different from that of normophonic subjects. In this paper we propose a procedure for the systematic collection of such pathological voices and the development of AI-based automatic tools to support differential diagnosis. Guidelines are provided concerning most suitable recording devices, vocal tasks and acoustical parameters, in order to simplify, speed up and make the whole procedure homogenous and replicable. The proposed procedure was applied to a set of 56 subjects, affected by Costello syndrome (CS), Down syndrome (DS), Noonan syndrome (NS) and Smith-Magenis syndrome (SMS). The whole database has been divided into three groups, respectively called: paediatric subjects (PS, individuals < 12 years of age), female adults (FA) and male adults (MA) subjects. In line with literature results, the Kruskal-Wallis test and post-hoc analysis with Dunn-Bonferroni test highlighted several significant differences in acoustical features not only between healthy subjects and patients, but also across syndromes within PS, FA and MA groups. Machine learning provided for the PS group a k-nearest neighbour classifier with 75% accuracy, for the FA group a support vector machine (SVM) model with 84% accuracy and for the MA group a SVM model with 97% accuracy. These preliminary results suggest that the proposed procedure, based on acoustical analysis and AI, might be helpful for an effective non-invasive automatic characterization of genetic syndromes.

The beginning of industrialization human being has observed a variety of environmental troubles in the world. This industrialization has not only brought growth and affluence but ultimately troubled the ecosystem. One of the crashes is visible, in form of water contamination. Here the current study heavy metal contamination of water body has been discussed. Effluents from a great number of industries viz., tannery, textile, pigment & dyes, paint, wood processing, petroleum refining, electroplating, leather etc., have a major amount of heavy metals in their wastewater. The conventional technique of handling heavy metal pollution includes chemical oxidation, chemical precipitation, ion exchange, reverse osmosis, membrane separation, electrodialysis etc. These processes are expensive, energy intensive and frequently related with generation of poisonous by-product. Therefore, the adsorption has been examined as a cost-efficient technique of elimination of heavy metals from wastewater. In the current study different low-cost adsorbent has been a review as an abatement of heavy metal contamination from wastewater. These adsorbent comprise materials of natural origin like peat moss, zeolites, clay, and chitin are found to be an effective agent for removal of deadly heavy metals like Pb, Cd, Zn, Cu, Ni, Hg, Cr etc. Separately from these, a variety of agricultural wastes like rice husk, waste tea, neem bark, black gram; Turkish coffee, walnut shell etc. were also known as a powerful adsorbent for heavy metal removal. at the side of that low-cost industrial byproduct like fly ash, lignin, iron (III) hydroxide and red mud, coffee husks, Areca waste, tea factory waste, sugar beet pulp, battery industry waste, blast furnace sludge, waste slurry, sea nodule remains and grape stalk wastes have been discovered for their technical possibility to eliminate toxic heavy metals from impure water.

Wild strawberry (Fragaria vesca L.) leaves possess diverse antioxidant properties, mainly due to the different classes of phenolics. In this study, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) of wild strawberry phenolics were carried out to understand the impact of extraction temperature, extraction time and solvent-to-sample ratio (SSR) on the quantitative and qualitative properties of the obtained extracts. The highest total phenolic content (8027 mg GA/100 g DW), as well the highest DPPH• antiradical activity (903 mol TE/g DW) was obtained with ASE at 150 °C, static time 5 min and SSR of 40:1; while the highest ABTS•+ antiradical activity (681 mol TE/g DW,) and FRAP (2389 mol TE/g DW) was obtained with MAE after 5 min at 80 °C and a SSR of 40:1. The correlation analysis showed that phenolics largely contributed to the antioxidant properties of the studied MAE extracts, while correlation was not found in ASE extracts. A total of 54 different phenolics were identified by UPLC/MS-MS in MAE and ASE extracts obtained at optimal extraction conditions. MAE extract was shown to have a higher content of phenolic acids (40%), but lower content of proanthocyanidins (88%), flavonols (29%), flavan-3-ols (50%) and flavones (39%) than ASE extract.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Data from ocean color (OC) remote sensing are considered a cost-effective tool for the study of biogeochemical processes globally. Satellite-derived chlorophyll, for instance, is considered an Essential Climate Variable since it is helpful in detecting climate change impacts. Google Earth Engine (GEE) is a planetary scale tool for remote sensing data analysis. Along with OC data, such tools allow an unprecedented spatial and temporal scale analysis of water quality monitoring in a way that has never been done before. Although OC data have been routinely collected at medium (~1 km) and more recently at high (~250 m) spatial resolution, only coarse resolution (≥4 km) data are available in GEE, making them unattractive for applications in the coastal regions. Data reprojection is needed prior to making OC data readily available in the GEE. In this paper, we introduce a simple but practical procedure to reproject and ingest OC data into GEE. The procedure is applicable to OC swath (Level-2) data and is easily adaptable to higher-level products. The results showed consistent distributions between swath and reprojected data, building confidence in the introduced framework. The study aims to start a discussion on making high resolution OC data readily available in GEE.

In this paper we evaluate the effects of hard and soft constraints on the Iterative Data Snooping (IDS), an iterative outlier elimination procedure. Here, the measurements of a levelling geodetic network were classified according to the local redundancy and maximum absolute correlation between the outlier test statistics, referred to as clusters. We highlight that the larger the relaxation of the constraints, the higher the sensitivity indicators MDB (Minimal Detectable Bias) and MIB (Minimal Identifiable Bias) for both the clustering of measurements and the clustering of constraints. There are circumstances that increase the family-wise error rate (FWE) of the test statistics, increase the performance of the IDS. Under a scenario of soft constraints, one should set out at least three soft constraints in order to identify an outlier in the constraints. In general, hard constraints should be used in the stage of pre-processing data for the purpose of identifying and removing possible outlying measurements. In that process, one should opt to set out the redundant hard constraints. After identifying and removing possible outliers, the soft constraints should be employed to propagate their uncertainties to the model parameters during the process of least-squares estimation.

Link prediction is a significant field in network science, which focuses on predicting the probability of the existence or formation of a link between nodes in a social network based on currently observed connections. The effectiveness of traditional algorithms can vary depending on the type of network, making some methods more suitable than others for specific scenarios. Recently, several efficient link prediction algorithms have been developed, demonstrating robust results in both prediction accuracy and interpretability. However, existing research has not clearly established the relationship between network characteristics and link creation mechanisms for community influence analysis and anomaly detection. The ability to predict complex networks with diverse features still requires further investigation. In light of this, we introduce a novel framework designed to combine the best features of different link prediction algorithms when applied to the network, with the aim of achieving more reliable predictions about how networks will evolve. According to the proposed framework, we first focus on the feature extraction stage. During this phase, we systematically identify and extract a comprehensive set of features from the network before moving onto the classification phase. Here, we utilize state-of-the-art ensemble learning models to assess and classify potential links within the network. By training our machine learning models on the extracted features, we can effectively predict whether a particular link is likely to form (positive link) or unlikely to form (negative link). The ML models were trained and evaluated using two datasets: Twitch and Facebook. Results: Additionally, we assessed their performance on these datasets by conducting specific preprocessing and hyperparameter tuning steps. The final prediction model achieves AUC values between 94% and 99.3%. This research contributes significantly to efforts aimed at enhancing link prediction in dynamic socisal network contexts, providing valuable insights into the effectiveness of different ML algorithms in predicting future connections and enhancing our understanding of network dynamics.

Melanins are phenolic biopolymers synthesised by most of the living organism mainly for photoprotection or surviving in harsh conditions. Melanin is localised in different areas or complexed with different other biomolecules when observed from animals to microbes. This makes the melanin extraction procedure different in animal, plant and microbial tissues. Basically, the alkali-acid extraction is used in most protocols of which slight variations are there depending on the tissue used. This review will try to compile melanin extraction procedures from different cells and tissues ranging from animals to bacteria.

(1) Background: Tooth extraction is one of the oldest and most well-known surgical procedures in dental medicine. It is still routinely performed to date by both general practitioners, oral surgeons, and dental undergraduates. The Benex extraction system allows for the extraction of teeth in vertical direction, which avoids most trauma against the surrounding alveolar bone and soft tissues; (2) Methods: The study included 56 patients who were recruited from the department of Oral Surgery at the Faculty of Dental Medicine, Medical University – Plovdiv. Patients were divided into two groups of 28 patients – Group I (control group) and Group II (study group). For each group the success of the extraction, buccal cortical plate preservation, pain experience and early wound healing were assessed; (3) Results: There was no statistical significance between the success of the extractions in both groups. The Benex extractions preserved the buccal cortical plate in 95% of the cases, whereas the forceps extractions only in 71.8%, which shows a statistical significance. On the seventh day patients in group II reported less pain, without a significant difference. There was a significantly bigger number of completely healed extraction wounds on the 10th day; (4) Conclusions: Atraumatic extractions allow for more hard and soft tissues to be preserved in the extraction site. This is all crucial for the successful outcome and aesthetically pleasing results of a following prosthetic or implant restoration.

Sweet cherry pomace is a by-product that can be a source of bioactive phenolic compounds. Usually, polyphenols have been extracted using conventional extraction methodologies. However, a significant fraction, called non-extractable polyphenols (NEPs), remains retained in the conventional extraction residues. Therefore, this work is aimed, for the first time, to investigate the release of NEPs from cherry pomace combining pressurized liquid extraction (PLE) and enzyme-assisted extraction (EAE) using Promod enzyme. A response surface methodology was employed to study the influence of temperature, time, and pH on the NEPs extraction. The response variables were the total phenolic content (TPC) measured by Folin-Ciocalteu method, total proanthocyanidin (PA) content evaluated by vanillin, DMAC, and butanol/HCl assays, and total antioxidant capacity determined by Trolox equivalent antioxidant capacity and inhibition of hydroxyl radical assays. The results indicated that PLE-EAE was more suitable and selective to obtain NEPs from sweet cherry pomace than PLE alone. In fact, the extracts obtained by PLE-EAE displayed higher TPC, PA content, and bioactivity than the extracts obtained by PLE under the same extraction conditions, and those obtained by conventional methods. Moreover, size-exclusion chromatography profiles showed that the combination of PLE and EAE enabled the recovery of NEPs with higher molecular weight than PLE without EAE treatment.

The viral nervous necrosis virus (VNNV) is the causative agent of an important disease affecting fish species cultured worldwide. Early and accurate diagnosis is at present the most effective control and prevention tool, and the molecular techniques have been strongly introduced and accepted by official organizations. Among those, real time quantitative polymerase chain reaction (rt-qPCR) is nowadays displacing other molecular techniques. However, another PCR-based technology, the droplet digital PCR (ddPCR), is on the increase. It has many advantages over qPCR, such as higher sensitivity and more reliability of the quantification. Therefore, we decided to design and validate a protocol for diagnosis and quantification of SJ and RG type VNNV, using reverse transcription-ddPCR (RT-ddPCR). We obtained an extremely low limit of detection, 10 to 100-folds lower than with RT-qPCR. Quantification by RT-ddPCR, with a dynamic range of 6.8 – 6.8 x 104 (SJ type) or 1.04 x 101 – 1.04 x 105 (RG) cps/rctn, was more reliable than with RT-qPCR. The procedure was tested and validated in field samples, providing the high clinical sensitivity and negative predictive values. In conclusion, we propose this method to substitute RT-qPCR protocols because it exceeds the expectations of qPCR in the diagnosis and quantification of VNNV.

Objectives: Minimally invasive direct coronary artery bypass (MIDCAB) is an alternative for revascularisation of isolated left anterior descending (LAD) or as multi-vessel (MV) procedure for diagonal branch (RD) or circumflex artery (RCX) region. Methods: From 2021 to 2022 91 patients underwent MIDCAB procedure in our heartcenter. 80% were male. Eighty percent of the patients had two or three vessel coronary artery disease. Mean age was 65±10 years. The left internal mammary artery (LIMA) was anastomosed to the left anterior descending via left minithoracotomy approach in all patients. Fourteen patients received multi-vessel MIDCAB (15%) with two or three anastomoses a saphenous vein graft (as T-graft to LIMA) was anastomosed to RD or RCX. Results: Mean operation time was 2.6±0.8 hours. The 30-day mortality was 0. Mean required packed red blood cells (pRBC) was 0.4±1.2 unit. The intensive care unit stay (ICU) was 1.5±1.6 days mean. We observed two patients (2%) with wound infections postoperatively. Four patients underwent rethoracotomy because of bleeding. Mean follow-up time was 1.5±0.5 years. Seventy-eight patients (86%) were in New York Heart Association (NYHA) class 1, 11 patients (12%) were in NYHA class 2. One patient received percutaneous coronary intervention due to de novo stenosis of the RCA. Late mortality was 2%. The Kaplan-Meier survival rate was 98.8% at 1 and 2 years. Conclusion: MIDCAB is technically demanding. Our postoperative and short-term clinical results demonstrate that this procedure is safe and feasible. Optimal patient selection and an experienced surgical team are mandatory.

One of the main challenges in geodetic deformation analysis is to infer whether the geometry of some engineering structures or zones of natural hazards has changed from their initial state or not. The pillar that supports such an analysis is tightly based on the fundamentals of statistical hypothesis testing. The null hypothesis model indicates that no displacement has occurred. It is tested against a class of alternative models, which stipulate different displacement patterns. In this contribution, we present an innovative geodetic displacement detection which integrates combinatorial analysis and likelihood ratio tests into a sequential procedure for the case where the differences between observations of two epochs are in play. This framework is applied and investigated to two test scenarios: a synthetic and a real simulated trilateration network. From a statistical point of view, our approach is rigorous, because the alternative model can identify simultaneously more than one unstable point. In addition, the relationship between the unknown parameters and the observations is always linear, even if the problem manifests itself as non-linear. Consequently, we avoid a potential loss of statistical test power due to the model linearization. In addition, the proposed method controls the false positive rate efficiently. One of the problems that arise here is also related to the selection of the maximum number of points to be considered in the test procedure ( ). Here, we provide an innovative methodology based on rank computation of the design matrices to define , which can even be extended to the problem of outlier detection. Determining avoids the problem of having non-separable models in identifying unstable points. The algorithms and data are available in the repository.

Congenital breast asymmetry represents a particular challenge to the classical techniques of plastic surgery due to a young group of patients. This study compares traditional breast augmentation using silicone implants to the more innovative lipograft technique regarding long-term results. To achieve this, we not only captured subjective parameters like satisfaction with outcome and symmetry, but also objective parameters such as breast volume and anthropometric measurements. Objective examination was performed manually and by using the Vectra® H2 photogrammetry scanning system. Patients who underwent implant augmentation and lipograft both showed no significant differences in patient´s satisfaction with surgical outcome (p = 0.55) and symmetry (p = 0.69). Furthermore, a breast symmetry of 93 % in both groups was reported. Likewise, no statistically significant volume difference between left and right breast was observed in both groups (p<0.41). However, on average, lipograft patients needed 1.3 procedures more until the desired result was achieved. In contrast, patients treated with implant-based breast augmentation usually need several implant changes during their life. In conclusion, both methods should be considered for patients with congenital breast asymmetry.

Evidence-based canine decontamination protocols are underrepresented in the veterinary literature. Aerosolized microbiological and chemical contaminants can pose a risk in deployment environments highlighting the need for improved canine field decontamination strategies. Prior work has established the efficacy of traditional, water-intensive methods on contaminant removal from the coat of the working canine; however, it is not known if similar reductions can be achieved with simple field expedient methods when resources are limited. The objective of this study was to measure the reduction of aerosolized contamination via a practical “wipe-down” procedure performed on working canine coats contaminated with a fluorescent, non-toxic, water-based aerosol. Disposable, lint-free towels were saturated with one of three treatments: water, 2% chlorhexidine gluconate scrub (CHX), or 7.5% povidone-iodine scrub (PVD). Both CHX and PVD were diluted at a 1:4 ratio. Treatments were randomly assigned to one of three quadrants established across the shoulders and back of commonly utilized working dog breeds (Labrador retrievers, n = 16; German shepherds, n = 16). The fourth quadrant remained unwiped, serving as a control. Reduction in fluorescent marker contamination was measured and compared across all quadrants. PVD demonstrated greater marker reduction compared to CHX or water in both breeds (P < 0.0001). Reduction was similar between CHX or water in Labradors (P = 0.86) and shepherds (P = 0.06). Effective wipe-down strategies using common veterinary cleansers should be further investigated and incorporated into decontamination practices to safeguard working canine health and prevent cross-contamination of human personnel working with these animals.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Background: A new access technique was developed to reduce postoperative adverse events after the extraction of impacted maxillary wisdom teeth. Hence, this study aimed to assess the occurrence of adverse events after extraction of maxillary impacted wisdom teeth using traditional or modified access. Methods: Two different surgical incision designs were used for bilateral wisdom tooth extractions in 30 patients. The traditional incision was performed distal to the second molar in the center of the tuberosity, followed by a buccal releasing incision. After tooth extraction the wound was secured by sutures. The new technique consists of an oblique incision from the distal palatal aspect of the tuberosity towards the buccal aspect of the second molar. After tooth extraction, cyanoacrylate glue was used on the wound. Results: Lower pain was reported by patients at the site treated with the new technique (p&lt;0.01). Edema, postsurgical bleeding, and hematoma were similar in both groups. The surgical time was shorter for the new technique (p&lt;0.01). Conclusions: The new technique applied for the extraction of impacted maxillary wisdom teeth reduced postsurgical pain and the duration of surgery.

Green and Roasted coffee oils are products rich in bioactive compounds, such as linoleic acid and diterpenes cafestol and kahweol, being a potential ingredient for food and cosmetic industries. An overview of oil extraction techniques most applied for coffee and their influence on the oil composition is presented. Both green and roasted coffee oil extractions are highlighted. Pressing, Soxhlet, microwave, and supercritical fluid extraction were the most used techniques used for coffee oil extraction. Conventional Soxhlet is most used on lab-scale, while pressing is by industry. Supercritical fluid extraction has also been evaluated due to the goal of increasing the coffee oil diterpenes content. One of the highlighted activities in Brazilian agribusiness is the industrialization of oils due to their increasing use in the formulation of cosmetics, pharmaceuticals, and foods. Green coffee oil (raw bean) has desirable bioactive compounds, increasing the interest of private companies and research institutions in its extraction process to preserve the properties contained in the oils.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

The process of Targeted Opinion Word Extraction (TOWE), a critical component of aspect-based sentiment analysis (ABSA), revolves around identifying opinionated words linked to specific aspect-terms within sentences. Existing deep learning approaches, while effective, often overlook the syntactic structure of sentences, a factor that previous studies have identified as beneficial for TOWE. In this study, we introduce the Syntactic-Enhanced Deep Learning Model (SEDLM) that integrates syntactic structures into deep learning frameworks for TOWE. Our approach leverages syntax-driven opinion potential scores and syntactic inter-word connections, enhancing model performance. Additionally, we introduce an innovative regularization strategy aimed at distinguishing word representations in TOWE tasks. Our comprehensive analysis reveals that SEDLM sets new benchmarks in performance across multiple standard datasets.

Patients with chronic renal failure and vascular diseases require the vascular access for hemodialysis procedure to be performed with the most possible comfort for the patient. Native vein graft has a longer-lasting term in the patients’ limb, lower risk of graft infection and lower price. Native vein graft is constructed from the great saphenous vein, if the diameter of the vessel is smaller than the diameters of vessels (brachial artery, cephalic vein) it is connected to in the cubital fossa region due to the risk of graft folding, that might occur, if the graft diameter is bigger than the diameter of one or both vessels, on which anastomosis is made. The most important sizes, that were taken before graft placement, are the length of the forearm compartment, the distance between the brachial artery and cephalic vein in the cubital fossa region, distance from an expected incision in the brachial artery to the middle of the forearm compartment, the distance between incision in cephalic vein to the middle of the forearm compartment, length of the great saphenous vein (the graft) and diameters of blood vessels, used in the procedure. Finally, the right position of the graft should be determined for the successful outcome of anastomosis creating procedure.

The procedures for the extraction and separation of lipids and nutraceutics from microalgae using classic solvents have been used many times. However, these production methods usually require expensive and toxic solvents. Based on our studies involving the use of eco-sustainable methodologies and alternative solvents, we select ethanol (EtOH) and cyclopentyl methyl ether (CPME) for extracting bio-oil and lipids from algae. Different percentage of EtOH in CPME favors the production of an oil rich of SFA useful to production biofuel or rich of compounds bioactive. The proposed method for obtain a rich extract of saturated or unsaturated fatty acids from dry algal biomass is disclosed is eco-friendly and allows a good extraction yield. The method is compared both in extracted oil percentage yield and in extracted fatty acids selectivity to extraction by supercritical carbon dioxide.

This paper addresses the atmospheric emissions from oil and gas extraction and production in Greece. The study was carried out in 2014 in the Kavala gulf, which currently is the only location of oil and gas production in Greece and where the exploration activities for hydrocarbons started in the late ‘60’s. This study presents the qualitative and quantitative characteristics of atmospheric emissions, in relation also to the emissions’ control management system. Particular reference is made to sulphur compounds since the existence of volcanic rocks results to increased amounts of H₂S. The results shows that, currently, atmospheric emissions of pollutants during extraction and production of hydrocarbons in Greece are very low and do not have any significant effect on air quality and climate change. Since it is expected that exploitation of hydrocarbons and oil and gas extraction and production will increase in the future, appropriate measures should be taken to ensure environmental protection, such as the development of integrated monitoring systems and the use of up to date emission control technologies.

Chitin and its derivative, chitosan, have diverse applications in fields such as agriculture, medicine, and biosensors, amongst others. Extraction is primarily conducted from marine sources, such as crustaceans, which have been the focus of optimization process studies. However, there are other sources that are more readily available, such as insects, where insufficient research has been conducted. The house cricket (Acheta domesticus) is a promising source for chitin extraction because of its high chitin content, availability, and short lifespan. Modern chemical chitin extraction methods have not been standardized due to the use of different reagents, molar concentrations, temperatures, and reaction times across publications. Therefore, in this study, the compositional analysis of Acheta domesticus cricket flour was determined: 2.62% humidity, 4.3% ash content, 56.29% protein, 13.35% fat, 23.44% carbohydrates, and 15.71% crude fiber content. After a drying, defatting, demineralization, deproteinization, and bleaching process, chitin extraction was performed, and chitosan was obtained via a deacetylation reaction. The demineralization process was standardized at 30ºC for 3 hours using HCl 2M, resulting in 95.85 ± 0.012%. The deproteinization process was optimized at 80ºC for 45 minutes using NaOH 2.56 M, yielding 46.37 ± 3.86%. Finally, the identity and physicochemical characteristics of the compounds were determined through characterization with FTIR, XRD, SEM and DSC.

Like other organisms, fungi produce extracellular vesicles (EVs) that are involved in various biological processes, including intercellular communication and the transport of molecules between cells. These EVs can be applied in fungal pathogenesis, virulence, and interactions with other organisms, including host cells, in the case of fungal infections. While some types of mycoses are relatively common and easily treatable, certain neglected mycoses pose significant public health challenges, such as sporotrichosis, chromoblastomycosis, and paracoccidioidomycosis. These infectious diseases can cause significant morbidity and disability, leading to a reduced quality of life for the patients. So, research about the virulence factor is essential to understand how fungi escape the immune system. In this context, this manuscript reviews the study of fungi EVs, their cargo, their obtaining, and their role during the infectious process, which is extremely important for understanding this neglected mycosis.

Structured extraction of emergency event information can effectively enhance the ability to re-spond to emergency events. This article focuses on the extraction of Chinese document-level emergency events, which mainly faces two key issues in this field: first, related datasets; Secondly, existing DEE (document-level event extraction) studies mostly use sequence annotation to extract candidate entities in the subtask of candidate entity extraction without considering the problem of role overlapping between candidate entities. On the one hand, this article constructs a Chinese document-level emergency extraction dataset, CDEEE, which first annotates the issues of argu-ment scattering, multiple events, and role overlapping. On the other hand, this article proposes a model RODEE for the problem of role overlapping in DEE tasks. This model first uses two in-dependent modules to represent the head and tail positions of candidate entities, then uses a multiplication attention mechanism to interact with the two to obtain a scoring matrix. Finally, role-overlapping candidate entities are predicted to assist in completing DEE tasks. Experiments were conducted on our manually annotated dataset, CDEEE, and the results showed that RODEE can effectively solve the problem of role overlapping in candidate entities and improve the performance of the DEE model.

Diffuse cavernous hemangioma of the rectum (DCHR) is a rare benign lesion of vascular malformation. According to previous studies, the most reported major symptoms of DCHR are recurrent painless rectal bleeding or iron deficiency anemia[1][2][3][4][5][6]. We present a case of an 8Y11M boy who was diagnosed with DCHR by MRI. The patient underwent Laparoscopic-assisted transanal distal sigmoidectomy and sigmoido-anal anastomosis（Laparoscopic Swenson Procedure）, and recovered well. After the operation, the child had short-term fecal incontinence and loose stools, which returned to normal after half a year. Regardless of age and symptoms, early and correct diagnosis and treatment of DCHR and postoperative restoration of normal anal function are necessary. Laparoscopic Swenson procedure may be a good option for the treatment of DCHR.

The KID (Koopmans in DFT) procedure usually applies in organic molecules of the closed–shell type. We used the KID procedure in an open–shell system for the first time to choose the most suitable density functional to compute global and local reactivity descriptors coming from the Conceptual Density–Functional Theory. From a set of 18 density functionals spread from the second until the fourth rung of the Jacob’s ladder: BP86, B97-D, BLYP, CAM-B3LYP, M06-L, M11-L, MN12-L, B3LYP, PBE0, N12-SX, M06-2X, M11, MN12-SX, CAM-B3LYP, LC-ωHPBE, ωB97X-D, APFD, MN15 and MN15-L, we concluded that CAM-B3LYP provides the best outcome.

Automatic speech recognition of native languages plays a crucial role in fostering inclusivity and preserving linguistic diversity. The Kashmiri language, an underrepresented Indo-Aryan dialect primarily spoken in the Kashmir Valley, poses substantial challenges for existing AI models due to its phonetic diversity and scant linguistic resources. This study addresses these hurdles by developing a robust spoken Kashmiri recognition system that employs dual feature extraction with spectrogram augmentation and a hybrid Convolutional Neural Network (CNN) and Gated Multi-Layer Perceptron (gMLP) model. Key to this endeavour is the creation of a high-fidelity dataset that captures the phonetic variations across Kashmiri dialects, focusing on twelve specific words. Through the integration of dual feature extraction, spectrogram augmentation, and the innovative hybrid modelling approach, our system attains an impressive 96% accuracy on the test dataset for classifying these twelve spoken words. This research not only enhances the generalization and resilience of spoken Kashmiri recognition systems but also represents a critical step towards advancing technology and safeguarding the Kashmiri language within this underrepresented linguistic domain.

As an important part of coastal wetlands, tidal flats provide unique ecosystem services and functions. China's tidal flats are significantly threatened by industrialization, urbanization, aquaculture expansion and coastline reconstruction, and there is an urgent need for sustainable strategies to balance the protection and utilization of tidal flats. Remote sensing technology can realize large-scale spatiotemporal research of tidal flats, comprehensively improve the ecological environment of coastal zones, and help achieve the overall planning goals of major projects for the protection and restoration of important ecosystems in China. In this study, based on GEE (Google Earth Engine) platform, Sentinel-2 (MSI), Landsat 8 (OLI) and Landsat 9 (OLI-2) remote sensing images were used to construct multi-source intensive time series remote sensing image collection, combined with MSIC-OA algorithm. The tidal flat data of China in 2018 and 2023 are extracted and analyzed. The results show as follows: 1) The overall classification accuracy of the tidal flat in 2023 is 95.19%, and the Kappa coefficient is 0.89; In 2018, they were 92.77% and 0.83 respectively. 2) The total tidal flat area in 2018 and 2023 is 8300.34km2 and 8151.54km2, respectively, a decrease of 148.80km2; 3) In 2023, estuarine and bay tidal flats will account for 54.88% of the total area, and most of the tidal flats will be distributed near river inlets and bays; 4) In 2023, the total length of the coastline adjacent to the tidal flat is 10196.17km, of which the artificial shoreline accounts for 67.06%, and the development degree of the tidal flat is 2.04, indicating that most of the tidal flat has been developed and utilized. The research results provide valuable reference for the scientific planning and rational utilization of tidal flat resources in China.

Industrial hemp (Cannabis sativa L.) is an attractive candidate for sustainable pest management due to its abundance of bioactive compounds with potential pesticidal properties. Solvent choice has a significant impact on the extraction efficiency of bioactive compounds. Deep Eutectic Solvents (DESs) are gaining popularity in extraction because they are safe and environmentally friendly, making them viable alternatives to organic solvents (OSs). This research first compared the extraction efficiency of OSs on the extraction of phytochemicals from the infloresences of two hemp varieties, Citrus and Cherry Dwarf. Inflorescences were extracted using three OSs, ethanol, ethyl acetate, and hexane. The highest level of cannabidiol (CBD; 0.69%) was extracted from Cherry Dwarf using ethanol while the level of delta-9 tetrahydrocannabinol THC (0.19%) was essentially the same in both. Therefore, Cherry Dwarf was selected to compare the extraction efficiency of DESs to the OSs. The DESs were choline chloride/ethylene glycol, citric acid/ethylene glycol, menthol/lauric acid, choline chloride/urea and choline chloride/glycerol. In the targeted analysis, choline chloride/ethylene glycol extracted the highest amount of CBD (0.87%) followed by choline chloride/urea (0.78%). As some DESs outperformed ethanol, the popular solvent for extracting cannabinoids, DESs are viable candidates to replace organic solvents.

Tooth extraction techniques have been refined over the years in order to be less traumatic and better preserve alveolar bone. A recently introduced extraction method involves the use of the Magnetic Mallet®, which allows the clinician to be more precise, faster and less traumatic. The aim of the present study was to clinically evaluate whether extractions performed by means of the Magnetic Mallet® can lead to less bucco-lingual bone resorption. Between February 2023 and June 2023, 9 patients with an average age of 62 years underwent 29 extractions using the Magnetic Mallet®. Sectoral CBCTs were performed in order to measure bucco-lingual bone thickness at time 0 (T0, before extraction) and 3 months after extraction (T3M). All the extractions were performed by 2 different expert operators using exclusively the magnetic mallet. For statistical analysis, a two-sample t-test was performed between the measurements taken at T0 and those taken at T3M in the 29 dental elements and between the difference in bone loss among the 2 different clinicians. 22 teeth were extracted in the upper jaw and 7 in the lower jaw. The average degree of mobility was 1. The average degree of force impressed by the instrument to extract the teeth was 2, while the average frequency of blows administered was 7. The average time taken for the extractions was 3½ minutes. After 4 months, the mean bucco-lingual bone resorption was 1.54 mm (SD: +-). The difference of bucco-lingual bone thickness between T0 and T3 was significant at an alpha significance level of 0.01. No difference were found in bone resorption based on the clinician. The use of the Magnetic Mallet® during tooth extraction led to less bucco-lingual bone resorption in the 3 months following dental extraction, compared to the traditional use of manual hammers, chisels and levers.