Key thermophysical properties necessary for the successful design and use of CoCrFeNi alloy in thermophysical applications have been measured experimentally, and the results have been compared with literature values and results previously obtained for commercial Ni-Cr alloys and equiatomic CoCrFeNi alloy. In particular, the thermal diffusivity, coefficient of thermal expansion (CTE), and specific heat capacity were measured for the as-cast and homogenized equiatomic CoCrFeNi alloy over a temperature range allowing the thermal conductivity to be calculated up to 1173 K. The thermal conductivity and thermal diffusivity of the equiatomic CoCrFeNi alloy were found to deviate from monotonic behavior in the temperature range from 773 to 1100 K. Such a deviation was previously observed in the behavior of the temperature dependence of CTE and specific heat capacity of the equiatomic CoCrFeNi alloy. The non-linear behavior is primarily the result of order/disorder phenomena for the as-cast and homogenized sample, as well as additionally for the as-cast sample, non-equilibrium solidification under arc melting conditions. The measured data of thermophysical properties are provided for thermally differently treated samples, and it is shown that there is a difference in the behavior of the temperature dependences of CTE, thermal diffusivity, and heat capacity.

An ion exchange dialysis (IED) is used in the recovery of aluminium from residue. In this papers, the face-centered central composite design (FC-CCD) of the response surface methodology (RSM) and desirability approach is used for experimental design, modelling and process optimization of a counter flow IED system. The feed concentration, feed flowrate, sweep flowrate and sweep concentration are selected as the process variables, with the Al-transport across a Nafion 117 membrane as the target response. A total of 30 experimental runs were conducted with 6 center points. The response obtained was analysed by analysis of variance (ANOVA) and fitted to a second-order polynomial model using multiple regression analysis. The actual R2 and standard deviation of the model are 0.9548 and 0.2932 respectively. The influences of significant variables are plotted on 3D surface and contour plots. The designed variables were numerically optimized by applying the desirability function to achieve the maximum Al-transport. The optimised condition values were found to be feed concentration (1600 ppm), feed flowrate (61.76%), sweep flowrate (37.50%) and sweep concentration (0.75 N) for the 80% target response at 32hrs. Overall, the model can be used to effectively predict Al-recovery using the designed system

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

We evaluate some binomial cubic Fibonacci sums.

In this paper, we proposed the fusion of two projection based face recognition algorithms: local binary Patterns in DCT domain and singular value decomposition (SVD) characterized by its simplicity and efficiently. Standard databases ORL are used to test the experimental results which prove that proposed system achieves more accurate face recognition as compared to individual method.

The cubic nonlinearity of graphene oxide (GO) monolayer was characterized by open and closed Z-scan using a nano-second laser of 10 Hz repetition rate with a Gaussian spatial beam profile. The reverse saturable absorption or positive nonlinearity from open Z-scan and valley-peak traces or positive nonlinearity from closed Z-scan was displayed. The reverse saturable absorption could be from a two-photon or two-step excitation process due to the larger absorption in the lower visible and upper UV wavelength region compared with the excitation source. The nonlinear absorption and nonlinear refraction coefficient were estimated to be ~ 2.62x10-8 m/W and 3.9x10-15 m2/W, respectively. This study also reveals the effect of nonlinear absorption on nonlinear refraction traces.

Sensory integration is an essential function of human life, and its decline causes difficulties in the quality of life, especially in older adults. In this study, we proposed an arm-reaching task based on a virtual reality head-mounted display (VR-HMD) system to assess sensory integration in daily life, and examined whether reaching task performance was associated with age and resting-state functional connectivity (rsFC) between the brain regions of interest involved in sensory integration. We hypothesized that performance during a reaching task with multiple cognitive loadings would be affected by aging. The gap angle between the reaching hand and target positions was compared between older and middle-aged adults as a measure of sensory integration function. In addition, rsFC, which was significantly correlated with the gap angles of individual participants in the older adult group, was identified using resting-state functional magnetic resonance imaging data. The mean gap angle was significantly larger in the older adults than in the middle-aged group and was also significantly correlated with connections between the left primary motor area and the left inferior temporal gyrus, temporo-occipital part. Because the connectivity between the areas is known to be related to visuomotor integration, the results suggest the involvement of visuomotor integration in the decline of sensory integration function in old age and the validity of the gap angle during the proposed VR-HMD task as an index for the decline in function.

Autonomous vehicle technology, employing image sensors for road marking recognition, is largely dependent on the Lane Departure Warning System (LDWS) to prevent vehicular deviations from driving lanes. The effectiveness of image-based lane recognition, however, is susceptible to environmental influences like weather conditions and the surrounding road environment. This study investigates the impact of road marking retro-reflectivity on LDWS under varied environmental conditions. Conducted at the Yeoncheon SOC Demonstration Research Center, the experiments encompassed a spectrum of weather scenarios, incorporating rainfall and shifts between day and night lighting. Controlled wear was applied to white, yellow, and blue road markings, followed by measuring their retro-reflectivity at different stages of degradation. The LDWS's performance was evaluated by assessing the recognition rates of these markings under these diverse environmental settings. The study reveals that enhanced retro-reflectivity significantly boosts LDWS detection, especially in challenging weather conditions. Furthermore, the research led to the development of a simulation framework to analyze the cost-effectiveness of road marking maintenance, aligning it with the safety needs of autonomous vehicles. This framework suggests the necessity for updated road marking guidelines that cater to the advanced needs of driver assistance systems and autonomous vehicle technology.

Collaborative action between families and health professionals, in this case nurses, doctors, nutritionists, pharmacies in forming harmonious support is the philosophy of family centered nursing care which aims to involve families as the main focus in care. The aim of this literature review is to identify family-centered family member care: a literatu review. This language method uses literature reviews which are summaries of 10 articles in the publication years of 2020-2021 on search 4 databased electronic searches containing namely Scopus, ProQuest, Pubmed, and Scient Direct. This review used prisms. The eligibility of these studies were from its title, abstract, research methodology, results and discussion. The results of the review were presented in narrative form. The results of a review of 10 articles found that the form family centered care Conclusion: The family is considered a partner in the care of other family members. The concept of family centered care is a philosophy in nursing where the role of the family is very important in caring for family members who are sick.

This paper addresses the development of knowledge and assessment-centered learning approaches within a reflective learning framework in a first year physics class in a university faculty. The quality of students’ reflections was scored using a Self-reporting Reflective Learning Appraisal Questionnaire at the end of each learning approach. The results showed the differences between the approaches based on reflections on the learning control through self-knowledge, by connecting experience and knowledge, as well as through self-reflection and self-regulation. Assessment-centered activities fundamentally help students identify aspects of their attitudes towards, as well as regulate, their sustainability learning education.

Neutrosophic cubic set is the hybridization of the concept of neutrosophic set and interval neutrosophic set. Neutrosophic cubic set has the capacity to express the hybrid information of both the interval neutrosophic set and the single valued neutrosophic set simultaneously. As newly defined, little research on the operations and applications of neutrosophic cubic sets appear in the current literature. In the present paper we propose the score, accuracy functions for neutrosophic cubic sets and prove their basic properties. We firstly develop TODIM method to solve multi attribute group decision making in neutrosophic cubic set environment, which we call NC-TODIM. Also, we solve a MAGDM problem using the proposed NC-TODIM method to show the applicability and effectiveness of the developed method. We also conduct sensitivity analysis to show the impact of ranking order of the alternatives for different values of attenuation factor of losses for multi-attribute group decision making problem.

Neutrosophic cubic set (NCS) is one of the important family members of neutrosophic hybrid sets. Neutrosophic cubic set has more strength than other family members of neutrosophic hybrid sets to express incomplete information due to the presence of interval valued neutrosophic set (IVNS) and single valued neutrosophic set (SVNS) in its structure. Cross entropy measure is one of the best way to calculate the divergence of any variable from the priori one variable. In this paper we first define a new cross entropy measure under NCSs environment which we call NC- cross entropy measure. We investigate the basic properties of NC-cross entropy. We also propose weighted NC-cross entropy and investigate its basic properties. We develop a novel multi attribute decision making (MADM) strategy based on weighted NC-cross entropy. To show the feasibility and applicability, we solve a MADM problem using the proposed strategy.

Patients with a psychotic disorder frequently report oral health problems, while mental health nurses (MHNs) seem not to be fully aware of these problems and the risk factors. Therefore, this study aims to develop supportive tools for MHNs regarding oral health to increase sensitization among MHNs and to provide MHNs with knowledge to recognize (potential) oral health problems in patients with a psychotic disorder. We used a human-centered design in which the user, MHNs as well as experts by experience, were placed in the centre of the research process. Problems and needs in MHNs working with patients with a psychotic disorder were addressed. To identify key issues of problem as well as the needs in terms of resources, we started with focus groups (n = 9). We analysed the data thematically based on context of patients and MHNs in practice regarding oral health, preferred oral health tools focused on MHN, and intended outcomes of tools. A Multi Criteria Decision Matrix was developed and analysed (n = 9) to identify the most optimal and viable solution based on established criteria and issues that are prevalent in the work of MHNs. Most promising result was the development of a brochure with an awareness screener. The brochure with awareness screener was developed as a low-fidelity prototype for MHNs regarding oral health in patients with a psychotic disorder, based on the latest scientific evidence. After testing it, the feasibility was tested through semi-structured interviews (n=19). MHNs and experts by experience were satisfied with the tool and provided recommendations for adjustments to the content. Significant augmentations to the brochure include a clinical lesson and a toothbrush with toothpaste for patients. We can conclude that a brochure with an awareness screener is feasible for MHNs. Future steps aiming to further refine and optimize care processes for oral health tools in MHNs, should take refining eligibility criteria for psychiatric populations and the language level of the target group of a tool into account.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

The pursuit of sustainable wellbeing is one of the research objectives of positive experience design. Driven by this goal, the purpose of this paper is to provide an impact-centered sustainable positive experience design model. Firstly, the literature review method was used to define the research status and concept of impact-centered sustainable design. Secondly, an impact-centered sustainable positive experience design model was constructed, and relevant formulas for concept generation and concept evaluation were proposed. Thirdly, design verification was conducted through a workshop. Finally, the Technology Acceptance Model (TAM) questionnaire was used to evaluate and discuss the design model. An impact-centered sustainable positive design model was proposed, which includes the important impact dimensions of sensory experience and meaningful experience on users’ quality of life at different levels: healthy living (pleasure index, health behavior), harmonious community (social connectivity, social contribution), and livable environment (living environment, environmental contribution). Based on positive experience related theory, this study takes long-term impacts as the starting point for sustainable positive experience design, which helps designers to generate design concepts from a systematic and long-term perspective.

Background: Health management is gaining importance as a business resource to enhance employee well-being. The rise of remote work during COVID-19 impacted lifestyle habits. This study explores the impact of tele-exercise intervention on remote workers' lifestyle habits, aiming to improve health and productivity. Methods: This study divided into remote (G1) and face-to-face (G2) groups. Over three months, G1 followed a 30-minute weekly exercise program. Measurements and questionnaires were collected at three time points covering areas like presenteeism, weight, sleep, stress, job satisfaction, and happiness. Data underwent Two-way repeated measures ANOVA, Autocorrelation, Correlation Analysis, and Correspondence Analysis to assess differences and relationships between G1 and G2. Results: ANOVA showed that a significant difference was observed in Daily Stress (DS) between G1 and G2, with G1 exhibiting higher DS. Autocorrelation Analyses showed for G1 that strong relationships each of BMI, Presenteeism (PST), Daily Stress (DS), Stress Relief (SR), Sleep Quality (SQ), Purpose of Work (PW), and Satisfaction of Life (SL) in the time frame. Correlation Analysis showed for G1 that the pairs of PRS and SQ, and DS and SL had strong positive relationships, and the pairs of BMI and PRS, and BMI and SQ had strong negative relationships. Autocorrelation Analyses showed for G2 that strong relationships each of SR, Stress due to Remote Work (SRW), ST, SQ, and PW in the time frame. Correspondence Analysis showed that that G1 was encompassed in a job and life satisfaction area, and G2 was encompassed in a sleep and stress for weight control area.

Consuming fish sustainably means consuming less and better, considering environmental, social, and economic impacts. This demands more knowledge to make informed decisions. In this study, the main goal was to understand how sustainability education can be used as a tool to raise awareness and promote new habits regarding the sustainable consumption of fish in 4th-grade students at primary school. During the COVID-19 pandemic, face-to-face and online learning methodologies were used in two different groups of students to understand whether the teaching method impacted learning. A sequential explanatory mixed methodology was applied, with a pre-test/post-test design, combined with focus group sessions. Between the pre and post-tests three learning modules were performed. The results showed that the students were unaware of many aspects related to fish sustainable consumption, but the developed activities significantly increased their knowledge of the subject and impacted students to change their consumption behaviours. It was also found that the construction of knowledge by the students after the activities was achieved either by face-to-face or online learning. Interviews from focus group sessions showed that students got to know new fish species, learned about the concept of minimum landing size and closure season and that fish are labelled like other types of food.

Human Face and facial parts are the most significant parts as it reveals a person’s true identity. It plays an important role in various biometric applications like crowd analysis, human tracking, photography, cosmetic surgery, etc. There are many techniques are available to detect a facial image. Among them, skin detection is the most popular one. The aim of this paper is to detect first the person's identity from facial image and finally check any spot present the the detected person. The first step is to detect the maximum skin region based on a combination method of RGB and HSV color space model. Next it is to verify the skin areas of human through machine learning approach. The Aggregated Channel Features (ACF) detector is used to identify the different facial parts like eye pairs, nose, and mouth. Bootstrap aggregation decision tree classifier is applied to classify the person’s identity based on Histogram Oriented Gradient (HOG) features value. The experimental results show that the proposed method gives the average 97% accuracy.

Nowadays, fostered by technological progress and contextual circumstances such as economic crisis and pandemic restrictions, remote education is living a growing deployment. However, this growth generated widespread doubts about the actual effectiveness of remote/online compared to face-to-face education. The present study aimed at comparing face-to-face and remote education through a multimodal neurophysiological approach. It involved forty students at a driving school, during a real classroom, experiencing both the modalities. Wearable devices to measure brain, ocular, heart and sweating activities were employed in order to analyse the students’ neurophysiological signals to obtain insights about their cognitive dimension. In particular, four parameters were considered, the Eye Blink Rate, the Heart Rate and its Variability and the Skin Conductance Level. Also, the students filled a questionnaire at the end to obtain an explicit measure of their learning performance. Data analysis showed a higher cognitive activity, in terms of attention and mental engagement, in presence with respect to remote modality. On the other hand, students by remote felt more stressed, in particular during the first part of the lesson. Analysis of questionnaires demonstrated worst performance by remote, thus suggesting a common “disengaging” behaviour when attending remote courses, thus undermining their effectiveness. In conclusion, neuroscientific tools could help to obtain insights about mental concerns, often «blind», such as attentional decreasing and stress increasing, as well as their dynamics during the lesson itself, so allowing to define proper countermeasures to emerging issues when introducing new practices into daily life.

With the increase of intelligent voice phishing and the increasing reliance on open banking systems, there has been a rise in cases where individuals' personal information has been exposed, resulting in significant financial losses for the victims. Non-face-to-face transactions in the financial sector face challenges such as customer identification, ensuring transaction integrity, and preventing transaction rejection. Blockchain-based distributed ledgers have been proposed as a solution, but their adoption is limited due to the difficulty of managing private keys and the burden of gas fees management. This paper proposes a non-face-to-face P2P real-time token payment system that minimizes the risk of key loss by storing private keys in a keystore file and database through a server-based key management module. The proposed system simplifies token creation and management through a server-based token management module and implements an automatic gas charging function for smooth token transactions. Transaction integrity and non-repudiation are ensured through a transaction confirmation module that uses transaction IDs without exposing personal information. Furthermore, advanced security measures such as blocking foreign IP access and DDoS defense are implemented to securely protect user data. The proposed system aims to provide a convenient, secure, and accessible online payment solution to the public by implementing a self-authentication function using a web application that is not limited to smart phones or application platforms.

During the COVID-19 outbreak, most university courses have been offered on online platforms. A sudden shift from face-to-face classroom learning to online formats could influence the learning effectiveness of classes. This study aims to investigate differences in the learning effectiveness of online and face-to-face lecture courses. It also explores factors that impact the effectiveness of online instruction. These factors include interactions among learners, interactions between learners and the instructor, the quality of online platforms, learners’ ability to use devices and follow instructions, and learners’ situational challenges. The study participants were 261 university students at King Mongkut’s University of Technology Thonburi in Bangkok, Thailand. All participants were enrolled in at least one lecture course, such as history, humans and the environment, the environment and development, or general philosophy, during the 2019 academic year. A questionnaire was distributed to participants after they completed these courses in May 2020. Paired simple t-test analyses were used to compare the effectiveness of online and face-to-face classes, and a multiple regression analysis was used to identify factors that impact the learning effectiveness of online classes. The results show that online classes are less effective than face-to-face courses. The multiple regression analysis also revealed that the effectiveness of online learning was significantly impacted by learners’ ability to interact with classmates during class, their ability to interact with instructors after the class, the quality of online platforms, and disturbances or distractions in learners’ environments.

Introduction: Family-centered care (FCC) is currently taking a greater role in health care, due to the increasing empowerment of the parental experience. This literature aims to find out the study of the philosophy of child nursing services based on Family Centered CareMethode: The study of this literature through the search of scientific publications ranges from 201 7-2022. The databases used are Pubmed, Science Direct, and Proquest. The literature search was conducted according to the topic with four keyword groups based on Medical Subject Heading (MeSH) and combined with Boolean operators AND, OR and NOT, keywords Child AND Family AND Centered AND Care. Result: The study of the philosophy of child nursing services based on Family Centered Care is conducted based on the study of ontology, epistomotogi and axiology. Family-centered care (FCC) is a philosophy that emphasizes partnerships between parents and health care staff. The FCC's basic principles in neonatal intensive care units (NICs) are unlimited parental presence and parental participation, shared responsibility and decision-making about infant hospital care, and open communication between parents and staff. A family-centered treatment approach has benefits such as maintaining a bond between the child and the family, allowing the family to engage in child care, and minimizing the negative effects of hospitalization on the child and family.Conclusion: FCC is beneficial for nurses in terms of efficiency and effectiveness of time in the care process and increases professional satisfaction. Therefore, the implementation of the FCC is more effective and the satisfaction of clients and families is more increased.

In this paper we have studied some properties for determinant-calculating for cubic-matrix of order 2 and order 3. These properties are analogous to some properties for determinants of square matrix we have proved and noted that these properties also are applicable (or not in some details) on this concept for cubic-matrix of orders 2 and 3. All results in this paper, are presented in detail during the theorem proofs.

The release profiles of methotrexate, an anticancer drug, from the monoolein liquid crystalline cubic phases were studied. The cubic phases were used either in the form of a lipidic film deposited onto a glassy carbon electrode surface or in the dispersed form of magnetocubosomes, which are considered a prospective hybrid drug delivery system. Commonly, cubosomes or liposomes are employed, but not in the case of toxic methotrexate, known to block receptors responsible for folate transport into the cells. The release profiles of the drug from the lipidic films were monitored electrochemically and described using the Higuchi model. They were also modified via changes in temperature; the release was faster, although deviating from the model when the temperature was increased. Magnetocubosomes - cubic phase nanoparticles containing hydrophobic magnetic nanoparticles placed in an alternating magnetic field of low frequency and amplitude, stimulated drug release from the suspension, which was monitored spectroscopically. These new biocompatible hybrid materials are very promising, allowing to control the release of the drug at the appropriate sites, but do require further investigations into their in vitro cytotoxicity and in vivo biodistribution.

In this paper, we consider the fourth-order parabolic equations with integer and fractional order time derivatives with Neumann boundary conditions. The integer order time derivatives are approximated by backward Euler difference quotients, and the fractional order time derivatives are approximated by L1 interpolation. We propose the block-centered finite difference scheme for fourth-order parabolic equations of integer and fractional order time derivatives. We prove the stability of the block-centered finite difference scheme and the second-order convergence of the discrete L2 norms of the approximate solution and its derivatives of every order. Numerical examples are given to verify the effectiveness of the block-centered finite difference scheme.

Schizophrenia continues to be an illness with poor outcome. Most mechanistic changes occur many years before the first episode of schizophrenia; these are not reversible after the illness onset. A developmental mechanism that is still modifiable in adult life may center on intracortical glutathione (GSH). A large body of pre-clinical data has suggested the possibility of notable GSH-deficit in a subgroup of patients with schizophrenia. Nevertheless, studies of intracortical GSH are not conclusive in this regard. In this review, we highlight the recent ultra-high field magnetic resonance spectroscopic studies linking GSH to critical outcome measures across various stages of schizophrenia. We discuss the methodological steps required to conclusively establish or refute the persistence of GSH-deficit subtype and clarify the role of the central antioxidant system in disrupting the brain structure and connectivity in the early stages of schizophrenia. We propose in-vivo GSH quantification for patient selection in forthcoming antioxidant trials in psychosis. This review offers directions for a promising non-dopaminergic early intervention approach in schizophrenia.

When in doubt, asking a peer can be very helpful. Students learn a lot of social strategies from peers. However, stated preference studies [Newman, 1993] have found that for elementary school students with math questions they prefer to ask the teacher. In this paper, we study revealed preferences instead of stated preferences. We analyze the behavior of fourth-grade students seeking face-to-face assistance while working on an online math platform. Students start by working independently on the platform before the teacher selects two or three tutors from among those who have answered 10 questions correctly. Each student is then able to choose between the teacher or one of these tutors when requesting assistance. We study the students’ preferences over 3 years, involving 88 fourth-grade classes, 2,700 students, 1,209 sessions with classmate tutors, and a total of 16,485 requests for help when there was an option to choose between a teacher or a classmate. We found that students prefer asking classmates for help 3 times more than asking their teachers when given the choice. Furthermore, this gap increases from the first to the second semester. We also found that students prefer to request help from classmates of the same sex and of higher academic performance. In this sense, students from the two highest tertiles sought help from classmates in the same two tertiles, and students from the medium tertile prefer to seek help from students of the highest tertile. However, students in the two lowest tertiles do not prefer asking for help from students from the top tertile more than from their own tertiles.

Face recognition is one of the most active research fields of computer vision and pattern recognition, with many practical and commercial applications including identification, access control, forensics, and human-computer interactions. However, identifying a face in a crowd raises serious questions about individual freedoms and poses ethical issues. Significant methods, algorithms, approaches, and databases have been proposed over recent years to study constrained and unconstrained face recognition. 2D approaches reached some degree of maturity and reported very high rates of recognition. This performance is achieved in controlled environments where the acquisition parameters are controlled, such as lighting, angle of view, and distance between the camera-subject. However, if the ambient conditions (e.g., lighting) or the facial appearance (e.g., pose or facial expression) change, this performance will degrade dramatically. 3D approaches were proposed as an alternative solution to the problems mentioned above. The advantage of 3D data lies in its invariance to pose and lighting conditions, which has enhanced recognition systems efficiency. 3D data, however, is somewhat sensitive to changes in facial expressions. This review presents the history of face recognition technology, the current state-of-the-art methodologies, and future directions. We specifically concentrate on the most recent databases, 2D and 3D face recognition methods. Besides, we pay particular attention to deep learning approach as it presents the actuality in this field. Open issues are examined and potential directions for research in facial recognition are proposed in order to provide the reader with a point of reference for topics that deserve consideration.

Interaction of an electromagnetic field with matter in a laser cavity without the assumption of a fixed direction of the transverse electric field, described by the two-level Maxwell-Bloch equations, is studied. By using a perturbative nonlinear analysis, performed near the laser threshold, we report on the derivation of the laser (3+1)D vectorial complex cubic-quintic complex Ginzburg-Landau equation. Furthermore, we study the modulational instability of the plane waves both theoretically using the linear stability analysis, and numerically, using direct simulations via the split-step Fourier method. The linear theory predicts instability for any amplitude of the primary waves. Our numerical simulations confirm the theoretical predictions of the linear theory as well as the threshold of the amplitude of perturbations. The system understudy shows a deep dependence on the laser cavity parameters, for which there appear wave patterns in accordance with the predictions from the gain spectrum.

In the present study, we derive a new B-spline technique namely trigonometric B-spline collocation algorithm to solve some initial boundary value problems for the nonlinear Klein-Gordon equation. In order to carry out the time integration with Crank-Nicolson implicit method, the order of the equation is reduced to give a coupled system of nonlinear partial differential equations. The collocation approximation based on trigonometric cubic B-splines for spatial discretization is followed by the linearization of the nonlinear term. The efficiency and accuracy of the present method are validated by measuring the error between the numerical and analytical solutions when exist. The conservation laws representing momentum and energy are also computed for all problems.

A clinical simulation web-based program, known as FIRST2ACT (Feedback Incorporating Review and Simulation Techniques to Act on Clinical Trends) is designed to increase the efficacy of cli-nicians’ actions in the recognition and immediate response to a patient’s deterioration. This study, which was nested in a larger mixed method project, used ten focus groups (n=65) of graduate, enrolled, registered nurses, Associate Nurse Unit Managers, and general manag-ers/educators/coordinators from four different institutions to investigate whether nurses felt their practice was influenced by participating in either a face-to-face or web-based simulation educa-tional programme about patient deterioration. Results indicate individuals who were less ‘tech-savvy’ appreciated the flexibility of web-based learning, which increased their confidence. Face-to-face students appreciated self-reflection through performance evaluation. While face-to-face simulations were unable to completely duplicate symptoms, they did show nurses' adaptability. Both interventions enhanced clinical practice by improving documentation and re-plies while also boosting confidence and competence. Web learners initially experienced tech-related anxiety, which gradually subsided, demonstrating healthcare professionals' resilience to new learning approaches. Overall, the study highlighted the advantages and challenges of web-based and face-to-face education in clinical practice, emphasising the importance of adapta-bility and reflective learning for healthcare professionals. Further exploration of specific topics is required to improve practice, encourage knowledge sharing among colleagues, and improve early detection of patient deterioration.

According to the International Agency for Research on Cancer (IARC) of the World Health Organization (data of year 2020), Breast Cancer (BC) is one of the most common cancer types worldwide, with large geographical variations occurring between countries and world regions and highest incidence rates in countries that have undergone economic transition. The risk factors for BC include women ageing, genetic mutations, reproductive history, dense breast tissues, personal history of BC or specific non-cancerous breast diseases, family history of breast or ovarian cancer, previous treatment using radiation therapy, and exposure to hormone-like drugs such as diethylstilbestrol (DES). Additional risk factors include being overweight or having obesity after menopause, and taking hormones. MicroRNAs (miRNAs or miRs) are small non-coding RNA molecules that have an essential role in gene expression and are significantly linked to the tumor development and angiogenesis process in different types of cancer, including BC. In the last years, the knowledge about miRNAs role in BC has significantly improved, and complex interactions among coding and non-coding RNA has been elucidated. In this context, an increasing number of papers had been published regarding the role of miR-125 in BC. In this review, we summarize the state-of-the-art about this research topic in addition to elaborating on the need to set novel ethical and legal standards for the governance of such innovations in healthcare.

Brain-computer interfaces (BCI) from electroencephalography (EEG) provide a practical approach to support human-technology interaction. In particular, motor imagery (MI) is a widely-used BCI paradigm that guides the mental trial of motor tasks without physical movement. Here, we present a deep learning methodology, named Kernel-based Regularized EEGNet (KREEGNet), leveled on Centered Kernel Alignment and Gaussian Functional Connectivity, explicitly designed for EEG-based MI classification. The approach proactively tackles the challenge of intra-subject variability brought on by noisy EEG records and the lack of spatial interpretability within end-to-end frameworks applied for MI classification. KREEGNet is a refinement of the widely accepted EEGNet architecture, featuring an additional kernel-based layer for regularized Gaussian functional connectivity estimation based on CKA. The superiority of KREEGNet is evidenced by our experimental results from binary and multi-class MI classification databases, outperforming the baseline EEGNet and other state-of-the-art methods. Further exploration of our model’s interpretability is conducted at individual and group levels, utilizing classification performance measures and pruned functional connectivities. Our approach is a suitable alternative for interpretable end-to-end EEG-BCI based on deep learning.

Although child-centred care is increasingly referred to within the nursing literature, a clear definition of child-centred care and clarity around the concept is yet to be achieved. The objectives of this review were to examine: 1) What constitutes the concept of child-centred care in healthcare? 2) How has the concept of child-centred care developed? 3) What is the applicability of child-centred care and what are its limitations? and 4) How does the concept of child-centred care benefit and inform children’s healthcare? In total, 2984 papers were imported for screening, following removal of duplicates and screening, 21 papers were included in the scoping review.The findings suggest that child-centred care is an emerging, ambiguous, poorly defined concept; no clear consensus exists about what constitutes child-centred care. Although it seems antithetical to argue against child-centred care, little robust evidence was identified that demonstrates the impact of, and benefit from, child-centred care. If child-centred care is to be a sustainable, convincing model to guide practice and compete with other models of care it needs to establish robust evidence of its effectiveness, impact on children and their families as well as the wider impacts on the healthcare system.

Pancreatic ductal adenocarcinoma (PDAC) a highly malignant neoplasm, is classified as one of the most severe and devastating types of cancer. PDAC is a notable malignancy that exhibits a discouraging prognosis and a rising occurrence. The interplay between diabetes and pancreatic cancer exhibits a reciprocal causation. The identified metabolic disorder has been observed to possess noteworthy consequences on health outcomes, resulting in elevated rates of morbidity. The principal mechanisms involve the suppression of the immune system, the activation of pancreatic stellate cells (PSCs), and the onset of systemic metabolic disease caused by dysfunction of the islets. From this point forward, it is important to recognize that pancreatic cancer-related diabetes (PCRD) has the ability to increase the likelihood of developing pancreatic cancer. This highlights the complex relationship that exists between these two physiological states. Therefore, we investigate into the complex domain of PSCs, elucidating their intricate signaling pathways and the profound influence of chemokines on their behavior and final outcome. In order to surmount the obstacle of drug resistance and eliminate PDAC, researchers have undertaken extensive efforts to explore and cultivate novel natural compounds of the next generation. Additional investigation is necessary in order to comprehensively comprehend the effect of PCRD-mediated apoptosis on the progression and onset of PDAC through the utilization of natural compound. This study aims to examine the potential anticancer properties of natural compound in individuals with diabetes who are undergoing chemotherapy, targeted therapy, or immunotherapy. It is anticipated that these compounds will exhibit increased potency and possess enhanced pharmacological benefits. According to our research findings, it is indicated that naturally derived chemical compounds hold potential in the development of PDAC therapies that are both safe and efficacious.

Objective: To map the literature pertaining to adult Person-Centered Rehabilitation (PCR).Data Sources: Following our previously published scoping review protocol, data were identified through: three major databases, snowball searches and expert consultation.Study Selection: Two independent reviewers identified English-language papers which addressed adult physical rehabilitation and met one or more of the six pre-defined inclusion categories for PCR content. Data Extraction: Two independent reviewers extracted key characteristics of included papers (e.g. aims, methods, participants). Quantitative methods (descriptive statistics, regression analysis) and qualitative content analyses were used to synthesize the results. Data synthesis: Of 5084 unique records initially screened, 145 papers were included: 111 empirical, including 11 systematic reviews. Empirical papers had data from 13498 clients and 3849 providers, in total. Yearly publications grew exponentially from 2000 to 2017 (r²= 0.65; p<0.01). Publications were unevenly distributed by countries (e.g. United States’ publications per population size was 45 times lower than New Zealand’s). Most papers focused in more than one profession, setting-type or health conditions, respectively 57.2%, 66.2%, and 60.7%. Finally, more than half of the empirical papers (53.2%) studied implementation of PCR approaches, including its effect. Conclusion: This scoping review synthesizes key characteristics and publication trends in the PCR literature, which is mainly empirical and growing exponentially over time. Stakeholders can use the identified trends, gaps, and literature map to guide further PCR research, and both clinical and organizational practices. The high prevalence of papers focused on multiple professions, settings-type, or health conditions reinforces the need for developing a transdisciplinary, trans-service model of PCR, which will be derived from a thematic analysis of this body of literature.

This study investigated the breakdown trend in an automated production with an aim to recommend the application of Reliability-centered maintenance (RCM) for an improved productivity via a new preventive maintenance (PM) program. Individual Section-forming machine (ISM): a glass blowing machine for making glass bottles was used as the case study of an automated production system. The machine parts and the working mechanisms were analysed with a special focus on methods of processes and procedures that will enable the ISM maintenance department run more effective and achieve its essential goal of ensuring effective machine operation and reducing machine downtime. In this work, information is provided on the steps and procedures to identify critical components of the ISM using Failure Modes and Effect Analysis (FMEA) as a tool to develop an optimal maintenance program based on the reliability data of the equipment’s functional components. A relationship was established between the failure rate of the machine components and the maintenance costs such that using the recommended PM program, an evidence of improvement in the machine’s availability, safety and cost-effectiveness will result into an increase in the company’s profit margin.

Face verification for unrestricted faces in the wild is a challenging task. This paper proposes a method based on two deep convolutional neural networks(CNN) for face verification. In this work, we explore to use identification signal to supervise one CNN and the combination of semi-verification and identification to train the other one. In order to estimate semi-verification loss at a low computation cost, a circle, which is composed of all faces, is used for selecting face pairs from pairwise samples. In the process of face normalization, we propose to use different landmarks of faces to solve the problems caused by poses. And the final face representation is formed by the concatenating feature of each deep CNN after PCA reduction. What's more, each feature is a combination of multi-scale representations through making use of auxiliary classifiers. For the final verification, we only adopt the face representation of one region and one resolution of a face jointing Joint Bayesian classifier. Experiments show that our method can extract effective face representation with a small training dataset and our algorithm achieves 99.71% verification accuracy on LFW dataset.

Given the AdS/CFT relationship, the study of higher-dimensional AdS black holes is extremely important. Furthermore, since the restriction derived from $f(Q)$'s field equations which prevents it from deriving spherically symmetric black hole solutions, the result is either $Q'=0$ or $f_{QQ}=0$. We derive static anti-de-Sitter black holes in $D$-dimensions using the cylindrical coordinate in the framework of the cubic form of $f(Q)$ gravity, where the coincident gauge condition is imposed \cite{Heisenberg:2023lru,Maurya:2023muz}. Within this study we are going to use the power-law ansatz which is the most viable according to observations where $f(Q)=Q+\frac{1}2\gamma Q^2+\frac{1}3\gamma Q^3-2\Lambda$, and the condition $D \geq 4$ is satisfied. Since these solutions lack a general relativity limit, they belong to a brand-new solution class, the characteristics of which are derived only from the non-metricity $Q$ modification. We investigate the singularities of the solutions by computing the values of different curvature and non-metricity invariants. We discover that the solutions indeed have a central singularity, but because of the f(Q) impact, it is softer than in the typical general relativity case. In conclusion, we compute thermodynamic parameters such as Gibbs free energy, Hawking temperature, and entropy. These thermodynamic calculations confirm that our model is stable.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

Over past decades, a frequent co-morbidity of cerebrovascular pathology and Alzheimer's disease pathology has been observed. Numerous published studies indicate that preservation of healthy cerebrovascular endothelium can be an important therapeutic target. By incorporating appropriate drug(s) into biomimetic (lipid cubic-phase) nanocarriers, one obtains a multitasking combination therapeutic which targets certain cell-surface scavenger receptors, mainly class B type 1 (i.e., SR-BI), and crosses the blood-brain barrier. This targeting allows for various Alzheimer’s-related cell types to be simultaneously searched out for localized drug treatment in vivo.

A probabilistic description is essential for understanding the dynamics of stochastic systems far from equilibrium, given uncertainty inherent in the systems. To compare different Probability Density Functions (PDFs), it is extremely useful to quantify the difference among different PDFs by assigning an appropriate metric to probability such that the distance increases with the difference between the two PDFs. This metric structure then provides a key link between stochastic systems and information geometry. For a non-equilibrium process, we define an infinitesimal distance at any time by comparing two PDFs at times infinitesimally apart and sum these distances in time. The total distance along the trajectory of the system quantifies the total number of different states that the system undergoes in time, and is called the information length. By using this concept, we investigate the information geometry of non-equilibrium processes involved in disorder-order transitions between the critical and subcritical states in a bistable system. Specifically, we compute time-dependent PDFs, information length, the rate of change in information length, entropy change and Fisher information in disorder-to-order and order-to-disorder transitions, and discuss similarities and disparities between the two transitions. In particular, we show that the total information length in order-to-disorder transition is much larger than that in disorder-to-order transition, and elucidate the link to the drastically different evolution of entropy in both transitions. We also provide the comparison of the results with those in the case of the transition between the subcritical and supercritical states and discuss implications for fitness.

This work introduces a novel facial image capture system that utilizes computer vision technology and artificial intelligence for real-time detecting, tracking, and capturing of human faces. The objective of this study is to address the challenges posed by poor-quality facial images in biometric authentication, especially in passport photo acquisition and recognition. By combining face-aware capture technology with AES encryption for secure image storage, we present a completely open-source hardware solution that consists of a Jetson processor, a 16MP autofocus RGB camera, a custom enclosure, and a touch sensor LCD for user interaction. Pilot data collection demonstrates the system's ability to capture high-quality images, achieving a 98.98% accuracy in storing images of acceptable quality. The integration of AES encryption ensures data security, making the proposed system suitable for real-time applications in other domains beyond identity verification in passport applications, such as security systems, video conferencing, etc

Face swapping is an intriguing and intricate task in the field of computer vision. Currently, most mainstream face swapping methods employ face recognition models to extract identity features and inject them into the generation process. Nonetheless, such methods often struggle to effectively transfer identity information, result in generated results failing to achieve a high identity similarity with the source face. Furthermore, if we can accurately disentangle identity information, we can achieve controllable face swapping, thereby providing more choices to users. In pursuit of this goal, we propose a new face swapping framework (ControlFace) based on the disentanglement of identity information. We disentangle the structure and texture of the source face, encoding and characterizing them in the form of feature embeddings separately. According to the semantic level of each feature representation, we inject them into the corresponding feature mapper and fuse them adequately in the latent space of StyleGAN. Owing to such disentanglement of structure and texture, we are able to controllablely transfer parts of the identity features. Extensive experiments and comparisons with state-of-the-art face swapping methods demonstrate the superiority of our face swapping framework in terms of transferring identity information, producing high-quality face images and controllable face swapping.

While the desire to uncover the neural correlates of consciousness has taken numerous directions, self-face recognition has been a constant in attempts to isolate aspects of self-awareness. The neuroimaging revolution of the 1990’s bought about systematic attempts to isolate the underlying neural basis self-face recognition. These studies, including some of the first fMRI (functional Magnetic Resonance Imaging) studies, revealed a right hemisphere bias for self-face recognition in a diverse set of regions including the insula, the Dorsal Frontal Lobe, the Temporal Parietal Junction and Medial Temporal Cortex. Confirmation of these data (which are correlational) was provided by TMS (Transcranial Magnetic Stimulation) and patients in which direct inhibition or ablation of right hemisphere regions leads to a disruption or absence of self-face recognition. These data are consistent with a number of theories including a right hemisphere dominance for self-awareness and/or a right hemisphere specialization for identifying significant social relationships including to oneself.

This article discusses the comparison between digital and traditional face-to-face coaching within the scope of shadow education institutions. While analyzing the differences and similarities between the two educational models, both their advantages and disadvantages are thoroughly discussed. In this context, interviews were conducted with students and teachers who receive education in both face-to-face and digital coaching, and the positive and negative aspects of both institutions, suitable and unsuitable courses, the future situation, and the effects on students' academic achievements were revealed. According to the results obtained from the research, it is noteworthy that students who do not receive education in digital coaching have prejudices against digitalization. Additionally, no significant difference was found between the academic achievements of students receiving education in digital coaching and those receiving education in face-to-face coaching.

This study measured secondary students’ digital literacy using a digital game-based assessment system that was designed and developed based on the Evidence-Centered Game Design (ECGD) approach. A total of 188 secondary students constituted the valid samples in this study. Fine-grained behavioral data generated from students’ gameplay processes were collected and recorded with the assessment system. The Delphi method was used to extract feature variables related to digital literacy from the process data, and the Analytic Hierarchy Process (AHP) method was used to construct the measurement model. The assessment results of the ECGD-based assessment had a high correlation with standardized test scores, which have been shown to be reliable and valid in prior large-scale assessment studies.

Activity of the Nox1 centered NADPH oxidase complex depends on the activator NoxA1 and the organizer NoxO1. NoxO1 itself is not involved in electron transfer for superoxide formation. Instead, by creating proximity of all components in the right place NoxO1 enables a constitutive formation of reactive oxygen species by that complex. All subunits should form the complex in a 1:1:1 ratio. When analyzing different cell lines in this study, we found an unequal expression of the component on mRNA level with an excess of NoxO1. Even with plasmid-based overexpression of individual components of Nox1 centered NADPH oxidase complex results in different expression of their mRNA, with NoxO1 mRNA being best expressed. Despite an unchanged high level of NoxO1 mRNA over a wide range of transfected plasmid, protein expression is increased with accelerating plasmid concentrations. We thought to analyze the ability of NoxO1 to induce ROS formation, when present in different ratio to Nox1 and NoxA1. To this end, we used Hek293 cells with constitutive expression of Nox1 and NoxA1 transfected with increasing concentrations of NoxO1. Our results suggest that ROS formation by the Nox1 centered NADPH oxidase strongly depends on the level of NoxO1 and a surplus of NoxO1 further increases the activity of the complex.

Cyber-Physical Systems form the new backbone of digital ecosystems. Their design can be coupled with engineering activities to facilitate dynamic adaptation and (re-)configuration. Behavior-oriented technologies enable highly distributed and while coupled operation of systems. Utilizing them for digital twins as self-contained design entities with federation capabilities makes them promising candidates to develop and run highly functional CPS. In this paper we discuss mapping CPS components to behavior-based digital twin constituents mirroring integration and implementation through subject-oriented models. These models, inspired by agent-oriented system thinking can be executed and increase transparency at design and runtime. Patterns recognizing environmental factors and operation details facilitate configuration of CPS. Subject-oriented runtime support enable dynamic adaptation and federated use.

Acute myocardial infarction (AMI) is a leading cause of morbidity and mortality worldwide. This study aimed to test the efficacy of a newly-developed symptom self-management program on health outcomes among inpatients post-AMI. A pilot randomised, controlled trial was utilised. A convenience sample of 90 was recruited from a tertiary hospital in Singapore. Adult inpatients with post-AMI were randomly assigned to the three groups: IManage-HSet, IManage-FF or control group. Sample size was computed using power analysis. Data were collected through self-reported questionnaires and physiological instruments. Data analyses included univariate statistics, analysis of variance and repeated measure analysis of variance. Ninety participants were recruited with 30 in each group. Participants in the IManage-HSet and IManage-FF group had significantly greater relaxation (ηp2 = 0.11), lower objective stress (ηp2 =0.14), and greater knowledge (ηp2 = 0.62) than those of the control group. The two intervention groups had lower subjective stress (ηp2 = 0.04), depression (ηp2 = 0.01), and anxiety (ηp2 = 0.03) than the control but such differences did not achieve statistical significance. Furthermore, most participants reported that they were satisfied with the programs and they provided positive comments on the contents, educational materials and relaxation practice. This pilot study supports the potential benefits and feasibility of the IManage-VR and IManage-FF interventions on stress, perceived relaxation, knowledge and patient satisfaction. Contents of the symptom management interventions could be added into current cardiac rehabilitation programs. Future RCTs with multi-centered sites and larger sample size are required to further test the intervention. This study was prospectively registered with the International Standard Randomised Controlled Trial on the 5th August 2014 with registration number ISRCTN61027816.

In the evolving landscape of higher education, St. Michael's College (SMC) recognizes the significant impact of the COVID-19 pandemic on student welfare. This paper emphasizes the critical importance of addressing mental health, time management, and stress in the college environment, underlining their influence on academic success and personal growth. The call to action urges students to prioritize their well-being. Diverse cultural and religious perspectives, including Islam, emphasize the importance of a balanced mind and body. The wide-ranging literature review uncovers empirically supported strategies for mental health, time management, and stress reduction. Personal autonomy emerges as crucial in addressing these challenges. This study underscores the importance of these dimensions, calls for student action, and highlights the diversity of perspectives contributing to holistic well-being.

This paper presents the development and implementation of a Pan-Tilt-Zoom (PTZ) camera interfaced with a Jetson processor hosting Artificial Intelligence (AI) algorithms, designed to address the challenges of traditional biometric capture for first-time passport photos of young children. The system enhances the accuracy, efficiency, and adaptability of facial biometric capture by recognizing and accommodating the dynamic and diverse behaviors of children. Utilizing AI, the system detects faces and analyzes facial features using 68 landmark points, ensuring high-quality images that meet ISO standards. These technical specifications, implementation process, and performance evaluations of the developed system are provided in this paper, demonstrating the potential of the proposed AI Face-Capture to advance biometric identification and verification for young children.

"Deep fake" technologies are often associated with face-swapping algorithms based on images or videos. Although much research is focused on developing these techniques, there is still room for improvement, especially in human and visual assessment. In this study, we present an innovative approach to the problem of face replacement based on one model while preserving background features. Our model uses the Adaptive Attentional Denormalization method from FaceShifter while integrating identity features from the ArcFace and BiSeNet models to support the attribute extraction process. We used Fast GAN as a generative model to optimize and accelerate the training process on smaller data sets. Our research proves the effectiveness of the proposed approach by combining innovative methods and architectures in one coherent solution.

Currently, face recognition technologies are the most widely used methods for verifying 1an individual’s identity. Nevertheless, it has increased in popularity, raising concerns about face spoofing attacks, in which a photo or video of an authorized person’s face is used to get access to services. Based on a combination of Background Subtraction (BS) and Convolutional Neural Networks (CNN), as well as an ensemble of classifiers, we propose an efficient and more robust face spoof detection algorithm. This algorithm includes a Fully Connected (FC) classifier with a Majority Vote (MV) algorithm, which uses different face spoof attacks (e.g., printed photo and replayed video). By including a majority vote to determine whether the input video is genuine or not, the proposed method significantly enhances the performance of the Face Anti-Spoofing (FAS) system. For evaluation, we considered the MSU MFSD, REPLAY-ATTACK, and CASIA-FASD databases. The obtained results by our proposed approach are better than those obtained by state of the art methods. On the REPLAY-ATTACK database, we were able to attain a Half Total Error Rate (HTER) of 0.62% and an Equal Error Rate (EER) of 0.58%. It was possible to attain an EER of 0% on both the CASIA-FASD and the MSU FAS databases.

The science around the use of masks by the general public to impede COVID-19 transmission is advancing rapidly. Policymakers need guidance on how masks should be used by the general population to combat the COVID-19 pandemic. In this narrative review, we develop an analytical framework to examine mask usage, considering and synthesizing the relevant literature to inform multiple areas: population impact; transmission characteristics; source control; PPE; sociological considerations; and implementation considerations. A primary route of transmission of COVID-19 is via respiratory droplets, and is known to be transmissible from presymptomatic and asymptomatic individuals. Reducing disease spread requires two things: first, limit contacts of infected individuals via physical distancing and other measures, and second, reduce the transmission probability per contact. The preponderance of evidence indicates that mask wearing reduces the transmissibility per contact by reducing transmission of infected droplets in both laboratory and clinical contexts. Public mask wearing is most effective at reducing spread of the virus when compliance is high. The decreased transmissibility could substantially reduce the death toll and economic impact while the cost of the intervention is low. Given the current shortages of medical masks we recommend the adoption of public cloth mask wearing, as an effective form of source control, in conjunction with existing hygiene, distancing, and contact tracing strategies. Because many respiratory droplets become smaller due to evaporation, we recommend increasing focus on a previously overlooked aspect of mask usage: mask-wearing by infectious people ("source control") with benefits at the population-level, rather than mask-wearing by susceptible people, such as health-care workers, with focus on individual outcomes. We recommend that public officials and governments strongly encourage the use of widespread face masks in public, including the use of appropriate regulation.

Local binary pattern is one of the visual descriptors and can be used as a powerful feature extractor for texture classification. In this paper, a novel representation for face recognition is proposed, called it Bilateral Line Local Binary Patterns (BL-LBP). This scheme is an extension of Line Local Binary Patterns descriptors in the statistical learning subspace. The present bilateral descriptors are fused with an ensemble learning of calibrated SVM models. The performance of this scheme is evaluated using 5 standard face databases. It is found that it is robust against illumination variation, diverse facial expressions and head pose variations and its recognition accuracy reaches 98 percent, running on a mobile device with a processing speed of 63 ms per face. Results suggest that our proposed method can be very useful for the vision systems that have limited resources where the computational cost is critical.

The endometrium, the inner mucosal lining of the uterus, undergoes complex molecular and cellular changes across the menstrual cycle in preparation for embryo implantation. Transcrip-tome-wide analyses have mainly been utilized to study the endometrial receptivity, the prerequisite for successful implantation, with most of the studies, so far, comparing the endometrial transcriptomes between (i) secretory versus proliferative endometrium or (ii) mid-secretory versus early-secretory endometrium. In the current study, we provide the complete transcriptome description of the endometrium across the entire menstrual cycle and, for the first time, comprehensively characterize the proliferative phase of the endometrium. Our temporal transcriptome analysis includes five time points: mid-proliferative, late-proliferative (peri-ovulatory phase), early-secretory, mid-secretory, and late-secretory phases. Thus, we exhaustively unveil the transitions between the consecutive proliferative and secretory phases, highlighting their unique gene expression profiles and possible distinct biological functions. Transcriptome analysis reveals many differentially expressed genes (DEGs) across the menstrual cycle, most of which are phase-specific. As an example of the coordinated gene activity, the expression profile of his-tone-encoding genes within the HIST cluster on chromosome 6 showed an increase in cluster activity during the late-proliferative and a decline during the mid-secretory phase. Moreover, numerous DEGs are shared among all phases. In conclusion, in the current study, we delineate the endometrial proliferative phase-centered view of transcriptome dynamics across the menstrual cycle. Data analysis highlights significant transcriptomic and functional changes occurring during the late-proliferative phase – an essential transition point from the proliferative to the secretory phase. Future studies should explore how the biology of the late-proliferative phase endometrium impacts the achievement of mid-secretory endometrial receptivity or contributes to molecular aberrations leading to embryo implantation failure.

Purpose: This study investigated the impact of the COVID-19 pandemic on mental health, quality of life, and family functioning in a sample of the general female population, exploring difficulties encountered in managing family and work responsibilities and burden of care when taking care of a loved one. The study was moreover aimed at investigating factors capable of influencing severe depressive symptomatology in the context of socio-demographics, traumatic events, individual vulnerability, and family functioning. Method: During a weekend devoted to Mental Health initiatives (October 8-10, 2021), 211 women were interviewed (47% exposed to the 2009 L’Aquila earthquake). Results: More than 50% of the sample reported a higher complexity in managing their lives during the COVID-19 pandemic compared to their previous routine, with no statistically significant differences between working women and non-workers, although the latter obtained higher scores for depressive symptomatology and poorer quality of life. Compared to non-caregivers, women caregivers (22.3%) in charge of the care of loved ones affected by physical (10.9%) or psychiatric disabilities (11.4%) complained of a poorer quality of life, with those caring for people affected by mental disorders seeming to experience a more significant worsening. Approximately 20% of the total sample reported severe depressive symptomatology. Previous access to mental health services (O.R. 10.923), low level of education (O.R. 5.410) and difficulties in management of their everyday lives during the COVID-19 pandemic (O.R. 3.598) were found to be the main variables predictive of severe depressive psychopathology. Old age, good problem-solving skills and ability to pursue personal goals were identified as protective factors. Conclusions: The COVID-19 pandemic underlined the need for support for emotionally vulnerable women with pre-existing mental health conditions, partly reflecting the cumulative effects of traumas.

This paper uses the $\exp(-\Phi(\xi))$-Expansion method to investigate solitons to the M-fractional nonlinear Schrödingers equation with cubic nonlinearity. The results obtained are dark solitons, trigonometric function solutions, hyperbolic solutions and rational solutions. Thus, the constraint relations between the model coefficients and the traveling wave frequency coefficient for the existence of solitons solutions are also derived.

We investigated and quantified bacterial accumulation in facemasks used by the general population, using 16S rRNA (Sanger Sequencing), culture and biochemical analysis along with Rose Bengal staining. Additionally, a systematic overview of the literature on face mask contamination was undertaken. We found an average bacterial load of 4.24 × 10⁴ CFU recovered/mask, with a maximum load of 2.85 × 10⁵ CFU. This maximum is 310 times higher than the limit value for contamination of ventilation system outlet surfaces specified by the German standard VDI 6022. Biochemical and molecular identification predominantly found Staphylococcus species (80%), including Staphylococcus aureus, along with endospore-forming Bacillus spp. Literature reports also indicate contamination of masks by bacterial and fungal opportunists of the genera Acinetobacter, Aspergillus, Alternaria, Bacillus, Cadosporium, Candida, Escherichia, Enterobacter, Enterococcus, Klebsiella (including K. pneumoniae), Micrococcus, Microsporum, Mucor, Pseudomonas, Staphylococcus and Streptococcus. Bacterial counts increase linearly with wearing duration, and prolonged use may affect the skin and respiratory microbiomes, promoting consequential eye, skin, oral and airway conditions. These aspects underscore the urgent need for further research and a risk-benefit analysis in respect of mask use, particularly given their unproven efficacy in disrupting the transmission of respiratory viruses and their adverse social consequences.

Natural killer T cells (NKT) are a subset of T lymphocytes bridging innate and adaptive immunity. These cells recognize self and microbial glycolipids bound to non-polymorphic and highly conserved CD1d molecules. Three NKT cell subsets, type I, II and NKT-like expressing different antigen receptors (TCR) were described and TCR activation promotes intracellular events leading to specific functional activities. NKT can exhibit different functions depending on the secretion of soluble molecules and the interaction with other cell types. NKT cells act as regulatory cells in the defence against infections but, on the other hand, their effector functions can be involved in the pathogenesis of several inflammatory disorders due to their exposure to different microbial or self antigens, respectively. A deep understanding of the biology and functions of type I, II and NKT-like cells as well as their interplay with cell types acting in innate (Neuthrophils, Innate Lymphoid cells, Machrophages and Dendritic cells) and adaptive immunity (CD4+,CD8+ and Double Negative T cells) should be important to design potential immunotherapies for infectious and autoimmune diseases.

Student-centered teaching practices such as active learning continue to gain momentum in college science education. Many instructors committed to these innovative practices transform their classroom beyond the standard lecture. Nevertheless, widespread implementation of these practices is limited because the learning benefits for students are often attained through increased instructional complexity to which many instructors cannot commit. When co-instructors are teaching the course, the level of commitment to building a student-centered classroom may be even more profound. For these reasons, new tools are needed to help instructors and co-instructors plan, organize, evaluate, and communicate their classroom innovations. Pathway modeling is a tool with potential to fill this gap. Unlike curriculum mapping -- which identifies academic content gaps, redundancies, and misalignments by examining a series of courses within a plan of study – course pathway modeling creates a visual map of a single course and reveals how teaching practices influence short-, mid-, and long-term student learning outcomes. This essay demonstrates how course pathway modeling can help co-instructors better represent the complexity of student-centered teaching practices. We include guides for creating course pathway models and discuss how this approach offers the potential to improve curricular design, course evaluation, student assessment, and communication between co-instructors.

The utilization of person centered care is highlighted as essential for health promotion, yet implementation has been inconsistent and multiple issues remain. There is a dearth of applied re-search exploring the facets of successful implementation. In this paper, a person centered wellbeing program spanning various groups is discussed outlining the central principles that have allowed for successful outcomes. The main data emerges from 10 years of pragmatic pre-post service evaluation. Measures of functional capacity and wellbeing were captured using validated measures. The method for this paper is a narrative exploration of the theory and practices that can explain the continual improvement the clinics have achieved over 10 years. Core principles relate to connecting with people, connecting through groups, and connecting with self. The operationalization and theoretical explanation of these principles is outlined alongside 10 years of data which shows sustained improvement in a range of outcomes. The discussion of these principles posits essential factors to prioritize to advance the implementation of person centered care in health promotion for long term conditions.

The mutton sheep breeding industry has transformed significantly in recent years, from traditional grassland free-range farming to a more intelligent approach. As a result, automated sheep face recognition systems have become vital to modern breeding practices and have gradually replaced ear tagging and other manual tracking techniques. Although sheep face datasets have been introduced in previous studies, they have often involved pose or background restrictions (e.g., fixing of the subject’s head, cleaning of the face), which restrict data collection and have limited the size of available sample sets. As a result, a comprehensive benchmark designed exclusively for the evaluation of individual sheep recognition algorithms is lacking. To address this issue, this study develops a large-scale benchmark dataset, Sheepface-107, comprised of 5,350 images acquired from 107 different subjects. Images were collected from each sheep at multiple angles, including front and back views, in a diverse collection that provides a more comprehensive representation of facial features. In addition to the dataset, an assessment protocol is developed by applying multiple evaluation metrics to the results produced by three different deep learning models: VGG16, GoogLeNet, and ResNet50, which achieved F1-scores of 83.79%, 89.11%, and 93.44%, respectively. A statistical analysis of each algorithm suggested that accuracy and the number of parameters were the most informative metrics for use in evaluating recognition performance.

In today's world it is very much important to maintain the security of information and its risks. The biometric-based techniques are very much useful in these problems. Among the several kinds of biometric-based technique, face detection is much complex and much more important. Due to the age and several other problems, a human face structure changes over time, again a human has lots of expressions. Sometimes due to the lighting condition or the variation of the angle of an input device, the pattern of a human face structure also changed. As a result, the face cannot be detected properly. In this paper, a method is proposed that can detect the human faces both automatically and manually very efficiently. In manual mode, a user can select the input faces referred by the system according to their choice. In automated mode, the system detected all possible face areas using the Kohonen Self-Organizing Feature Map technique. This method reduced the complex color image into a vector quantized image with desired colors. Then a color segmentation technique is used to detect the possible face skin areas from the vector quantized image. Then the Histogram Oriented Gradient technique used to detect the feature from the faces and K-Nearest Neighbour Classifier is used to compare both face images detected by the two modes. The automated method prosed better accuracy than the manual method.

Nowadays, security is a top priority. In fact, biometrics uses cutting-edge technologies to identify terrorists and criminals. But the practice of distinguishing humans based on intrinsic physical or behavior traits goes back thousands of years. With the widespread use of computers in the late 20th century, new possibilities for digital biometrics emerged and new technologies were generously used. Among these, we remember high resolution security video cameras and drones. So, the aim of the present project is to study and explain the features of these technologies, especially the ones of the the Phantom 4 Pro+ aircraft and analyze its operating methods in order to identify human faces during live streaming of videos. For this purpose, it will be used Paul Viola and Michael Jones’ face detection algorithm, which includes Haar features and cascade classifiers to identify faces, eyes and ears of an individual.

The adsorption of proteins on polymer is widely used in biosensors. Here, molecular dynamics (MD) simulation was used to study the immobilization of angiotensin converting enzyme II (ACE2) with six initial orientations proposed on polystyrene (PS) at the ambient conditions of pH (4.5, 6, 7, 8, 9.5) and NaCl (0.01, 0.05, 0.1, 0.15, 0.2, 0.25 M). ACE2 immobilization under favorable ambient conditions was characterized by minimum distance (short), settlement time (fast), interaction energy (substantial) and protein configuration (stable). ACE2 orientations proposed in 0.15M NaCl were respectively preferable to (90, 0, 0), (0, 0, 0) and (0, 270, 0), (180, 0, 0) and (0, 90, 0), (90, 0, 0) at pH 4.5, 6, 7, 9.5. ACE2 immobilization was further evaluated at pH 7 by optimizing NaCl concentration. Its proposed orientations of (i) (0, 270, 0), (ii) (0, 0, 0) and (90, 0, 0), and (iii) (0, 90, 0) and (90, 0, 0) were preferable in 0.05, 0.1 and 0.2 M NaCl, respectively. The great significance of cubic-orientation settlement mode provides tangible improvement for the microfabrication of biochips for rapid diagnosis of severe acute respiratory syndrome coronavirus II (SARS-CoV-2).

Copper ferrite attracts a lot of interest from researchers as a material with unique magnetic, optical, catalytic and structural properties. In particular, the magnetic properties of this material are structurally sensitive and can be tuned by changing the distribution of Cu and Fe cations in octahedral and tetrahedral positions by controlling synthesis parameters. In this study, we propose a new simple and convenient method for the synthesis of copper ferrite nanoparticles using a strongly basic anion exchange resin in OH form. The effect and possible mechanism of polysaccharides addition on the elemental composition, yield and particle size of CuFe2O4 is investigated and discussed. It is shown that anion exchange resin precipitation leads to a mixture of unstable at standard temperature cubic (c-CuFe2O4) and stable tetragonal (t-CuFe2O4) phases. The effect of the reaction conditions on the c-CuFe2O4 stability is studied by temperature-dependent XRD measurements and discussed in terms of the cations distribution, Jahn−Teller distortion and Cu2+ and oxygen vacancies in the copper ferrite lattice. The obtained differences in the values of saturation magnetization and the coercive force of prepared samples are explained with a reference to variations in the particle sizes and the structural characteristics of copper ferrite.

Although mask-wearing is now widespread, knowledge of how to quantify or improve its performance remains surprisingly limited and largely based on empirical evidence. The objective of this study was to visualize the expiratory airflows from facemasks and evaluate aerosol transmission between two persons. Different visualization methods were explored, including the Schlieren optical system, laser/LED-particle imaging system, thermal camera, and vapor-SarGel system. The leakage flows and escaped aerosols were quantified using a hotwire anemometer and a particle counter, respectively. The results show that mask-wearing reduces the exhaled flow velocity from 2~4 m/s (with no facemask) to around 0.1 m/s, thus decreasing droplet transmission speeds. Cloth, surgical, and KN95 masks showed varying leakage flows at the nose top, sides, and chin. The leakage rate also differed between inhalation and exhalation. The neck gaiter has low filtration efficiency and high leakage fractions, providing low protection efficiency. There was considerable deposition in the mouth-nose area, as well as the neck, chin, and jaw, which heightened the risk of self-inoculation through spontaneous face-touching. A face shield plus surgical mask greatly reduced droplets on the head, neck, and face, indicating that double face coverings can be highly effective when a single mask is insufficient. The vapor-SarGel system provided a practical approach to study interpersonal transmission under varying close contact scenarios or with different face coverings.

A Pogorelov polytope is a combinatorial simple 3-polytope realizable in the Lobachevsky (hyperbolic) space as a bounded right-angled polytope. It has no 3- and 4-gons and may have any prescribed numbers of k-gons, k ≥ 7. Any polytope with only 5-, 6- and at most one 7-gon is Pogorelov. For any other prescribed numbers of k-gons, k ≥ 7, we give an explicit construction of a Pogorelov and a non-Pogorelov polytopes. Any Pogorelov polytope different from Löbel polytopes can be constructed from the 5- or the 6-barrel by cuttings off pairs of adjacent edges and connected sums with the 5-barrel along a 5-gon with the intermediate polytopes being Pogorelov. For fullerenes there is a stronger result. Any fullerene different from the 5-barrel and the (5, 0)-nanotubes can be constructed by only cuttings off adjacent edges from the 6-barrel with all the intermediate polytopes having 5-, 6- and at most one additional 7-gon adjacent to a 5-gon. This result can not be literally extended to the latter class of polytopes. We prove that it becomes valid if we additionally allow connected sums with the 5-barrel and 3 new operations, which are compositions of cuttings off adjacent edges. We generalize this result to the case when the 7-gon may be isolated from 5-gons.

Cerebellar mutism syndrome (CMS), also known as posterior fossa syndrome, is encountered in a subset of children who have undergone an operative procedure of the posterior cranial fossa, mainly involving the vermis, and the most frequent underlying pathology is proved to be medulloblastoma. The most common characteristics of this syndrome include an often transient, although protracted, language impairment, emotional lability, along with cerebellar, and brainstem dysfunction. Nevertheless, a significant number of patients experience persistent neurological deficits and lasting neurocognitive impairment. A lot of research and clinical studies have been performed in order to better delineate this syndrome. The main obstacles in our way to highlight all aspects of this syndrome were related with an inconsistent nomenclature, poorly defined diagnostic criteria, and uncertainty surrounding risk factors and etiology. Currently, there is a combination of diagnostic criteria that are regarded as prerequisites in order to establish the diagnosis of CMS. These include language impairment and emotional lability, as proposed by the international Board of the Posterior Fossa Society in their consensus statement. Several risk factors are recognized as implicated in the pathogenesis of this syndrome, including midline tumor location, diagnosis of medulloblastoma, younger age at diagnosis, and preoperatively established language impairment. A proposed etiology of CMS includes disruption of the cerebellar outflow tracts, the cerebellar nuclei, and their efferent projections through the superior cerebellar peduncle. Specific treatment for CMS is lacking, and it continues to be directed at symptom management. Our aim is to present a comprehensive narrative review of CMS etiology, diagnosis, risk factors, clinical presentation, and clinical management. Moreover, we attempt to recognize the most widely recognized priorities of the research community in order to expand our knowledge in the era of diagnostics, prevention, and therapeutic options for patients suffering from CM, or who are at risk for development of this syndrome.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

This work investigates centered polygonal lacunary functions restricted from the unit disk onto symmetry angle space which is defined by the symmetry angles of a given centered polygonal lacunary function. This restriction allows for one to consider only the p-sequences of the centered polygonal lacunary functions which are bounded, but not convergent, at the natural boundary. The periodicity of the $p$-sequences naturally gives rise to a convergent subsequence, which can be used as a grounds for decomposition of the restricted centered polygonal lacunary functions. A mapping of the unit disk to the sphere allows for the study of the line integrals of restricted centered polygonal that includes analytic progress towards closed form representations. Obvious closures of the domain obtained from the spherical map lead to four distinct topological spaces of the "broom topology'' type.

Well-being is one of the pillars of positive psychology, which is known to have positive effects not only on the personal and professional lives of individuals, but also on teams and organizations. Understanding and promoting individual well-being is essential for staff health and long-term success, but current tools for assessing subjective well-being rely on time-consuming surveys and questionnaires, which limit the possibility of providing the real-time feedback needed to raise awareness and change individual behavior. This paper proposes a framework for understanding the process of non-verbal communication in teamwork, using video data to identify significant predictors of individual well-being in teamwork. It relies on video acquisition technologies and state-of-the-art artificial intelligence tools to extract individual, relative, and environmental characteristics from panoramic video. Statistical analysis is applied to each time series, leading to the generation of a dataset of 125 features, which are then linked to PERMA (Positive Emotion, Engagement, Relationships, Meaning, and Accomplishments) surveys developed in the context of positive psychology. Each pillar of the PERMA model is evaluated as a regression or classification problem using machine learning algorithms. Our approach was applied to a case study, where 80 students collaborated in 20 teams for a week on a team task in a face-to-face setting. This enabled us to formulate several hypotheses identifying factors influencing individual well-being in teamwork. These promising results point to interesting avenues for research, for instance fusing different media for the analysis of individual well-being in teamwork.

Nowadays, hydropower is the principal renewable; however, climate change increases extreme events such as floods, droughts, erosion, and sedimentation of rivers that produce uncertainty in hydroelectric generation. Thus, this document aims to analyze the climate change projections in the hydropower systems of Ecuador based on data from 14 projects studying the scenarios ac-cording to the Shared Socioeconomic Pathways from the Intergovernmental Panel on Climate Change. The study period starts from 2010 to 2020 with historical data, collects the tendency, defines a database year, and then projects the scenarios to 2050. The quantitative methodology uses a statistic on Ecuador's hydropower obtained inflow time series to calculate the deviation over the last years and develop a model to simulate future generation. The results show that the hydropower in Ecuador is expected to decrease considerably through 2050 due to meteorological changes. In this calculation of the Shared Socioeconomic Pathways, the selected scenarios show a reduction in SSP5 of 11.5%, SP2 of 16.2%, and SSP4 of 18.2% to 2050, concluding that the oppor-tunities for hydroelectric production facing climate change are variable, but the challenges are broad. In Ecuador, the projections of hydropower plants represent a sensitive issue of their re-ductions, especially knowing that the country had an energy grid in 2020 that depended on 87% of hydroelectric production.

Fighting against the COVID-19 pandemic caused by the SARS-CoV-2 virus is one of the most critical challenges facing the global health system today. The possibility to identify the group of persons in the cohort of people under 50 years old, who are sensitive to the COVID-disease by non-invasive methods, is a very perspective approach for estimating the epidemiological state of the human population. The study aimed to identify the features of people's faces with COVID-19 that the most correlate with disease severity could serve as one of these approaches. For this aim, 525 photos of patients' faces with different outcomes of COVID-19 disease were analyzed using the Dlib face recognition convolutional neural network pre-trained for face recognition. Face descriptor vectors were obtained using the convolutional neural network. Facial features were found that predict a person's sensitivity to the SARS-CoV-2 virus (disease severity), and the contribution of each of the features to the risk of developing a severe form of COVID in a person was found. The accuracy of the binary classification of the individual severity of the COVID-19 course using the k-nearest neighbors algorithm on the test dataset was accuracy - 84%, AUC - 0.90.

We prove general stability theorems for $n$-dimensional quartic-cubic-quadratic-additive type functional equations of the form \begin{eqnarray*} \sum_{i=1}^\ell c_i f \big( a_{i1}x_1 + a_{i2}x_2 + \cdots + a_{in}x_n \big) = 0 \end{eqnarray*} by applying the direct method. These stability theorems can save us much trouble of proving the stability of relevant solutions repeatedly appearing in the stability problems for various functional equations.

In today’s world face detection is the most important task. Due to the chromosomes disorder sometimes a human face suffers from different abnormalities. For example, one eye is bigger than the other, cliff face, different chin-length, variation of nose length, length or width of lips are different, etc. For computer vision currently this is a challenging task to detect normal and abnormal face and facial parts from an input image. In this research paper a method is proposed that can detect normal or abnormal faces from a frontal input image. This method used Fast Fourier Transformation (FFT) and Discrete Cosine Transformation of frequency domain and spatial domain analysis to detect those faces.

Face recognition is a valuable forensic tool for criminal investigators since it certainly helps in identifying individuals in scenarios of criminal activity like fugitives or child sexual abuse. It is, however, a very challenging task as it must be able to handle low-quality images of real world settings and fulfill real time requirements. Deep learning approaches for face detection have proven to be very successful but they require a large computation power and processing time. In this work, we evaluate the speed-accuracy tradeoff of three popular deep-learning-based face detectors on the WIDER Face and UFDD data sets in several CPUs and GPUs. We also develop a regression model capable to estimate the performance, both in terms of processing time and accuracy. We expect this to become a very useful tool for the end user in forensic laboratories in order to estimate the performance for different face detection options. Experimental results showed that the best speed-accuracy tradeoff is achieved with images resized to 50% of the original size in GPUs and images resized to 25% of the original size in CPUs. Moreover, performance can be estimated using multiple linear regression models with a Mean Absolute Error (MAE) of 0.113 what is very promising for the forensic field.

The study aimed to investigate how distributed leadership influences adolescents' social and emotional competence, considering the roles of student-centered instructional practices and teacher self-efficacy. Utilizing survey data from 7,246 Suzhou adolescents enrolled in the SESS program, the study employed multilevel structural equation modeling for analysis. The findings indicated a positive correlation between distributed leadership and adolescents' social and emotional competence, as evaluated by teachers. Moreover, distributed leadership was observed to exert an indirect impact on adolescents' self-assessment and teacher-rated social and emotional competence. This influence operated through several mediators: student-centered instructional practices, teacher self-efficacy, and the sequential mediating pathway of student-centered instructional practices → teacher self-efficacy. This study underscores the significance of supportive elements in fostering students' social and emotional competence. It offers valuable insights into the everyday practices of teachers, principals, and administrators. Additionally, it sheds light on how distributed leadership contributes to enhancing adolescents' overall social and emotional development.

Background: Different drugs damage the frontal cortices, particularly the prefrontal areas involved in both emotional and cognitive functions, with a consequence of decoding emotion deficits for people with substance abuse. The present study aims to explore the cognitive impairments in drug abusers through facial, body and disgust emotion recognition, expanding the investigation of emotions, processing, measuring accuracy and response velocity. Method: We enrolled 13 addicted to cocaine and 12 alcohol patients attending treatment services in Italy, comparing them with 33 matched controls. Facial emotion and body posture recognition tasks, a disgust rating task, and the Barrat Impulsivity Scale were included in the experimental assessment. Results: We found that emotional processes are differently influenced by cocaine and alcohol, suggesting that these substances impact diverse cerebral systems. Conclusion: The contribution made by the duration of consumption on emotional processing seems far less important than for cognitive processes. Drug abusers seem to be slower on elaboration of emotions and, in particular, of disgust emotion. Considering that the participants were not impaired in cognition, our data support the hypothesis that emotional impairments emerge independently from damage to cognitive functions.

Facial recognition systems are widely used systems around the globe. Their applications in real world scenarios like law enforcement, surveillance, ID card identification, information security, access control and many more has made them very important in today’s world. These systems have shown promising results and excellent performance; however, these systems need tremendous number of facial images for training before they are implemented in the real-world scenarios. The problem arises when we face lack of training images due to which the performance of such systems decreases exponentially. The problem becomes even worse when there is only one image per subject for training our facial recognition system, the probe image might contain variation like illumination, expression and disguise which are hard to be accurately recognized. Generative models have achieved great success for handling the lack of training data by generating synthetic data that resembles the original data. We have created a new method by fine tuning the basic Conditional Generative Adversarial Network (CGAN) to generate synthetic facial images provided only single image per subject. These synthetic facial images contain six variations that are smile, anger, stare, illumination and disguise. We increased the size of the dataset and then applied a convolutional neural network for facial recognition, which improved the accuracy of our system from 0.76 to 0.99.

With the continuous development of deep learning, the application of object detection based on deep neural network in the coal mine has been expanding. Simultaneously, as the production applications demand higher recognition accuracy, most research chooses to enlarge the depth and parameters of the network to improve accuracy. However, due to the limited computing resources in the coal mining face, it is challenging to meet the computation demands of a large number of hardware resources. Therefore, this paper proposes a lightweight object detection algorithm designed specifically for coal mining face, referred to as CM-YOLOv8. The algorithm introduces adaptive predefined anchor boxes tailored to the coal mining face dataset to enhance the detection performance of various targets. Simultaneously, a pruning method based on the L1 norm is designed, significantly compressing the model's computation and parameter volume without compromising accuracy. The proposed algorithm is validated on the coal mining dataset DsLMF+, achieving a compression rate of 40% on the model volume with less than a 1% drop in accuracy. Comparative analysis with other existing algorithms demonstrates its efficiency and practicality in coal mining scenarios. The experiments confirm that CM-YOLOv8 significantly reduces the model's computational requirements and volume while maintaining high accuracy.

Information-Centric Networking (ICN) is a new paradigm of network architectures that focuses on content, rather than hosts, as first-class citizens of the network. As part of these architectures, in-network storage devices are essential to provide end users with close copies of popular content, to reduce latency and improve overall experience for the user, but also to reduce network congestion and load on the content producers. To be effective, in-network storage devices, such as content storage routers should maintain copies of the most popular content objects. Adversaries that wish to reduce this effectiveness can launch cache pollution attacks to eliminate the benefit of the in-network storage device caches. Therefore, it is crucial to protect these devices and ensure the highest hit rate possible. This paper demonstrates per-face popularity approaches to reducing the effects of cache pollution and improving hit rates by normalizing assessed popularity across all faces of content storage routers. The mechanisms that were developed prevent the consumers, whether legitimate or malicious, on any single face or small number of faces from overwhelmingly influencing the content objects that remain in the cache. The results demonstrate that per-face approaches generally have much better hit rates than currently used cache replacement techniques.

In tunnel excavation with boring machines, the tunnel face is supported to avoid collapse and minimise settlement. This article proposes the use of reinforcement learning, specifically the Deep Q-Network algorithm, to predict the face support pressure. The approach is tested both analytically and numerically. By using the soil properties ahead of the tunnel face and the overburden depth as the input, the algorithm is capable of predicting the optimal tunnel face support pressure, adapting to changes in geological and geometrical conditions.

Single sample face recognition (SSFR) is a computer vision challenge. In this scenario, there is only one example from each individual on which to train the system, making it difficult to identify persons in unconstrained environments, particularly when dealing with changes in facial expression, posture, lighting, and occlusion. This paper suggests a different method based on a variant of the Binarized Statistical Image Features (BSIF) descriptor called Multi-Block Color-Binarized Statistical Image Features (MB-C-BSIF) to resolve the SSFR Problem. First, the MB-C-BSIF method decomposes a facial image into three channels (e.g., red, green, and blue), then it divides each channel into equal non-overlapping blocks to select the local facial characteristics that are consequently employed in the classification phase. Finally, the identity is determined by calculating the similarities among the characteristic vectors adopting a distance measurement of the k-nearest neighbors (K-NN) classifier. Extensive experiments on several subsets of the unconstrained Alex &amp; Robert (AR) and Labeled Faces in the Wild (LFW) databases show that the MB-C-BSIF achieves superior results in unconstrained situations when compared to current state-of-the-art methods, especially when dealing with changes in facial expression, lighting, and occlusion. Furthermore, the suggested method employs algorithms with lower computational cost, making it ideal for real-time applications.

This research aims to thoroughly understand the delicate interplay between stakeholders' perspectives, biometric data protection policies, and the deployment of face recognition technologies in Indonesia's dynamic digital world. Adopting a qualitative methodology, the study conducts Focus Group Discussions (FGDs) with various stakeholders, including government agencies, technology developers, regulatory agencies, civil society groups, and data subjects as end-users. Face-to-face group discussions facilitate an in-depth exploration of participants' perspectives, yielding rich qualitative data that reveals nuanced insights into the delicate balance between technological innovation, ethical considerations, and socioeconomic repercussions associated with implementing face recognition technology. The research comprehensively explains the difficulties and opportunities associated with responsible technological progress and biometric data security. The findings from the FGDs influence the development of strategies that effectively balance technical advancement with individual rights, privacy, and social well-being within the growing digital landscape of Indonesia. The regulatory function of the government seeks to bridge the gap between public expectations and technological advancements. Collaboration between academic institutions, government agencies, the private sector, and data subjects as end-users emerges as a crucial element, fostering an all-encompassing strategy integrating research, law, technology deployment, and user empowerment. This holistic approach is necessary to ensure that biometric data and facial recognition technology are utilized responsibly, thereby laying the way for Indonesia's technologically sophisticated and ethically aware digital future.

Currently, in the scientific literature there is a great interest on the study of strategies to implement patient-centered care. One of the main tools for this is the therapeutic relationship. Some studies suggest that the perception of the environment in which the physical therapy treatment takes place can influence the perception of its quality. A qualitative study using focus groups was performed. Two researchers conducted the focus groups, using a topic guide with predetermined questions. The focus group discussions were audio-recorded, transcribed verbatim and analyzed thematically using a modified grounded theory approach. The setting was three hospitals and six public health centers located in Spain. The inclusion criteria were patients who had received a minimum of 15 physical therapy sessions and with no communication impairments. Thirty-one participants in four focus groups. Participants described a series of specific experiences relating to the environment, which they felt were influential in the establishment of therapeutic patient-centered relationships, including eight physical factors and five organizational factors. The results of this study highlight environmental factors that affect the quality of the therapeutic patient-centered relationship in physical therapy and emphasize the need for physical therapists and administrators to rethink the situation and propose strategies for improvement.

With the rapid growth of the global mask market, consumers have put forward higher requirements for the functionality and ingredients of mask products. Conventional facial masks generally use ordinary non-woven fabrics as the mask base fabric, are frequently used with essence and contain preservatives. At the same time, they are susceptible to the influence of the external environment and are easily oxidized, which will cause the mask to deteriorate and skin allergic reactions. In addition, conventional facial masks exhibit poor skin fit, limited breathability, inadequate absorption of nutrient solutions, and easy to drip. The nanofiber mask prepared by electrospinning technology has a high specific surface area and high porosity, which enabling improved nutrient absorption by the skin, superior skin fit, and exceptional breathability. Nanofiber facial mask products can effectively solve consumer pain points and promote the high-end development of facial mask products. Therefore, this research combines needleless electrospinning technology to develop a novel solid-state, preservative-free, and quick-dissolving nanofiber facial mask that can be prepared on a large scale. Based on needleless electrospinning technology, this research deeply explores the process parameters and influencing mechanisms of quick-dissolving nanofiber facial masks, ultimately achieving the consistent production of nanofiber facial masks with optimal morphology. Comprehensive and evaluation of the structure and performance of nanofiber facial masks from micro and macro perspectives. The experimental results show that the mask morphology is optimal under the process conditions of using a spinning liquid of 20% collagen peptide solution, a spinning voltage of 30kV, a collection distance of 19cm, and a liquid supply speed of 130ml/h.

We investigate new graph characteristics namely total (vertex, edge) face irregularity strength of gen- eralized plane grid graphs Gmn under k-labeling Phi of type (Alpha, Beta, Gamma). The minimum integer k for which a vertex-edge labelled graph has distinct face weights is called the total face irregularity strength of the graph and is denoted by tfs(Gmn). In this article, the graphs G = (V;E; F) under consideration are simple, fi nite, undirected and planar. We will estimate the exact tight lower bounds for the total face irregularity strength of some families of generalized plane grid graphs.

Complex illumination condition is one of the most critical challenging problems for practical face recognition. In this paper, we propose a novel method to improve the illumination invariants for solving this challenge. Firstly, a new method based on the Lambert reflectance model is proposed to extract illumination invariant, which is less insensitive to complex illumination variations. Secondly, in order to repair the defects caused by process of illumination invariants extraction, Fast Mean Filter is utilized to smooth and remove noise. Lastly, for raising the richness of information in output image, a nonlinear normalization transformation is proposed. Compared with the state-of-the-arts, experimental results show that the proposed method can extract more robust illumination invariants. Apart from it, the richness of information in processed image is greater and superior performance in face recognition rate is superior.

Abstract: The pursuit of youth and attractiveness is a fundamental desire in contemporary society. For many individuals, the appearance of visible signs of aging, such as skin laxity, gravitational changes in facial and neck soft tissues, and loss of harmonious proportions, can be psychologically distressing. The choice of effective methods for addressing these changes depends on their specific characteristics, the patient's anatomical features, and the type of facial aging. The introduction of 3D imaging to determine the hyoid bone level, the volume of soft tissue structures in the cervico-mental area, ptosis of subplatysmal structures, and the volume of submandibular glands, in addition to ultrasound study of the submental projection at the preoperative stage, are key for taking the best decision regarding preoperative planning. This case report aims to illustrate how modern imaging techniques are a fundamental part of the preoperative assessment of the mid and lower third of the face to ensure the most favorable aesthetic outcomes for each patient. Key message: To attain harmonious results in surgical correction of age-related facial and neck changes, it is crucial to consider the patient's anatomical features and the extent of age-related alterations. A comprehensive facial analysis, taking into account the type of facial aging and employing a CT scan and ultrasound examination of the soft tissues in the chin region, facilitates the development of an individualized plan tailored to achieve the patient's desired outcome.

This study explored the electrocortical correlates of conscious and nonconscious perceptions of emotionally laden faces in neurotypical adult women with varying levels of autistic-like traits (Autism Spectrum Quotient - AQ). Event-related potentials (ERPs) were recorded during the viewing of backward-masked images for happy, neutral, and sad faces presented either below (16 ms - subliminal) or above the level of visual conscious awareness (167 ms - supraliminal). Sad compared to happy faces elicited larger frontal-central N1, N2, and occipital P3 waves. We observed larger N1 amplitudes to sad faces than to happy and neutral faces in High-AQ (but not Low-AQ) scorers. Additionally, High-AQ scorers had a relatively larger P3 at the occipital region to sad faces. Regardless of the AQ score, subliminal perceived emotional faces elicited shorter N1, N2, and P3 latencies than supraliminal faces. Happy and sad faces had shorter N170 latency in the supraliminal than subliminal condition. High-AQ participants had a longer N1 latency over the occipital region than Low-AQ ones. In Low-AQ individuals (but not in High-AQ ones), emotional recognition with female faces produced a longer N170 latency than with male faces. N4 latency was shorter to female faces than male faces. These findings are discussed in view of their clinical implications and extension to autism.

An inorganic solid electrolyte is the most favorable candidate for replacing flammable liquid electrolytes in lithium batteries. Lithium Lanthanum Zirconium Oxide (LLZO) is considered as a promising solid electrolyte due to its safe operating potential window (0-5V) combined with its good electrochemical stability. In this work, 250 g batches of pre-sintered Tadoped (Li7La3Zr1.6Ta0.4O12, TaLLZO) were synthesized for bulk production of dense LLZO electrolyte. A simple two-step thermal treatment process was developed. The first thermal step at 950 °C initiates nucleation of LLZO carefully controlling process parameters such as heating atmosphere, temperature and dopant concentration. In the second thermal step at 1150 °C, sintered discs were obtained as solid electrolytes, with relative densities of 96%. X-ray diffraction analysis confirmed the phase purity of the sintered TaLLZO disc, and refined data was used to calculate the lattice parameter (12.944 Å). Furthermore, the presence of the Ta dopant in the disc was confirmed through X-ray photoelectron spectroscopy (XPS) analysis. The ionic and electronic conductivity values of TaLLZO disc were 104 S cm-1 and 10-10 S cm-1, respectively. These values confirm that the prepared (Ta-LLZO) discs exhibit ionic conductivity while being electronically insulating, being suitable for use as solid electrolytes with the requisite electrical properties.

Background: There are limited evidence-based data to guide treatment recommendations for breast cancer (BC) patients ≥ 80 years (P80+). Identifying and addressing unmet needs are critical. Aims: Advocate-BREAST80+ compared the needs of P80+ vs. patients < 80 years (P80-). Methods: In 12/2021, a REDCap survey was circulated electronically to 6,918 persons enrolled in the Mayo Clinic Breast Disease Registry. The survey asked about concerns and satisfaction with multiple aspects of BC care. Results: 2,437 participants responded (35 % response rate); 202 (8.3%) were P80+. P80+ were less likely to undergo local regional and systemic therapies vs. P80- (p

Acacia dealbata Link, named Mimosa in Portugal, is an invasive hardwood species with potential for construction use, but research is limited. The available stock of small-diameter juvenile wood (sjw) logs can help reduce this gap, but tangential cracking at log ends challenges fastener connections. This study evaluated different treatments to control and reduce end-face cracking in sjw logs during air drying, an economical and environmentally friendly procedure. Extreme two-thirds of sixteen Mimosa logs were subjected to two treatments: one with longitudinal kerfs 15 mm deep along the length (2 and 3 kerfs) and the other with a hollow in the centre up to half the length (16 mm and 30 mm diameters). Over 219 days of air drying and compared with the central part, kerfing treatments significantly reduced outer wood tangential cracking (p &lt; 0.001), with the 3-kerf also reducing crack numbers (p &lt; 0.05) but increasing significantly cracks near the pith (p &lt; 0.01). The 30 mm central hollow significantly reduced central perforation cracking (p &lt; 0.05). Results suggest that a combined treatment approach could help mitigate cracking, enhancing the suitability of wild Mimosa logs for construction use.

Climate change is a big challenge for agriculture since it affects crop productivity and yield. The increase of droughts, salinity, and soil degradation are some of the main consequences of climate change. The use of microorganisms has emerged as an alternative to mitigate them. Among these microorganisms, dark septate endophytes (DSEs) have garnered more attention in recent years. Various studies show that their association with plants helps reduce the harmful effects of abiotic stresses and increases nutrient availability, allowing plants to thrive under adverse conditions. This work reviews the effect of DSEs and the subjacent mechanisms that will help plants develop a higher tolerance to climate change.

Background: The rapid flow of globalization makes the world free from barriers so that the existence of globalization gives birth to a new concept of "World Without Borders". This situation puts the character of millennials on the brink of collapse and needs to be straightened out. Based on the problems above, the researcher determines the question: How is the role of civic education in shaping millennial character in the era of globalization? Purpose: The purpose of this study is to determine the impact of the current globalization on society, as a form of knowledge of the importance of citizenship education as a shield in the era of globalization, knowing the role of civic education in shaping the character of the millennial generation. Method: The method used in this research is a literature review. The search for journals was carried out using the google scholar database with the keywords “citizenship educations”, “millennial generation”, and “globalization”. Feasibility studies are assessed based on title, abstract, and full text. Data analysis using qualitative analysis based on research findings. Results: The results of this study show the influence of globalization causes character problems in millennials increasing every year. The high nature of individualism, consumerism, and westernization shows the characteristics of Indonesia began to erode and eventually also impacted the moral damage. Therefore, prevention is necessary through citizenship education as the basis for character formation by the values of Pancasila.

Background: The rapid flow of globalization makes the world free from barriers so that the existence of globalization gives birth to a new concept of "World Without Borders". This situation puts the character of millennials on the brink of collapse and needs to be straightened out. Based on the problems above, the researcher determines the question: How is the role of civic education in shaping millennial character in the era of globalization? Purpose: The purpose of this study is to determine the impact of the current globalization on society, as a form of knowledge of the importance of citizenship education as a shield in the era of globalization, knowing the role of civic education in shaping the character of the millennial generation. Method: The method used in this research is literature review. The search for journals was carried out using the google scholar database with the keywords “citizenship educations”, “millennial generation”, and “globalization”. Feasibility studies are assessed based on title, abstract, and full text. Data analysis using qualitative analysis based on research findings. Results: The results of this study show the influence of globalization causes character problems in millennials increasing every year. The high nature of individualism, consumerism, and westernization shows the characteristics of Indonesia began to erode and eventually also impacted the moral damage. Therefore, prevention is necessary through citizenship education as the basis for character formation by the values of Pancasila.