Transparent materials used for facial protection equipment provide protection against microbial infections caused by viruses and bacteria, including multidrug-resistant strains. However, transparent materials used for this type of application are made of materials that do not possess antimicrobial activity. They just avoid direct contact between the person and the biological agent. Therefore, healthy people can get infected through contact of the contaminated material surfaces and this equipment constitute an increasing source of infectious biological waste. Furthermore, infected people can transmit microbial infections easily because the protective equipment do not inactivate the microbial load generated while breathing, sneezing, or coughing. In this regard, the goal of this work consisted of fabricating a transparent face shield with intrinsic antimicrobial activity that could provide extra-protection against infectious agents and reduce the generation of infectious waste. Thus, a single-use transparent antimicrobial face shield composed of polyethylene terephthalate and an antimicrobial coating of benzalkonium chloride has been developed for the next generation of facial protective equipment. The antimicrobial coating was analyzed by atomic force microscopy and field emission scanning electron microscopy with elemental analysis. This is the first facial transparent protective material capable of inactivating enveloped viruses such as SARS-CoV-2 in less than one minute of contact, and the methicillin-resistant Staphylococcus aureus and Staphylococcus epidermidis. Bacterial infections contribute to severe pneumonia associated with the SARS-CoV-2 infection, and their resistance to antibiotics is increasing. Our extra protective broad-spectrum antimicrobial composite material could also be applied for the fabrication of other facial protective tools such as such as goggles, helmets, plastic masks and space separation screens used for counters or vehicles. This low-cost technology would be very useful to combat the current COVID-19 pandemic and protect health care workers from multidrug-resistant infections in developed and underdeveloped countries.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

Dirofilariosis is an infectious disease caused by species of the Dirofilaria genus. It is manifested by the appearance of a subcutaneous swelling, especially in the eye region. We present the case of a 29-year-old patient that accused facial asymmetry in the right genian region. Following clinical and paraclinical evaluations, the diagnosis of parasitic cyst was established in the context of dirofilariosis with Dirofilaria repens (D. repens). Treatment consisted of surgical excision of the formation associated with prophylactic antibiotic medication. Macroscopic analysis of the excision piece revealed a structure that contains a cystic cavity and a filamentous form with a length of approximately 10 mM and a diameter of 1 mM. This is the first case of dirofilariosis located in the genian region reported in Romania. The overview of this pathology is important to raise awareness among physicians about its presence and its clinical variations.

Aiming at the problems of high labor intensity and high cost of manual picking, high loss rate of mechanical picking seeds, low mechanization level and difficult to guarantee the quality of picking plates in the process of picking plates of edible sunflower. Based on the principle of manual plate taking, a plate taking control system for sunflower harvesting table was designed. Through the research and analysis of the principle of taking the plate of the edible sunflower harvesting table. According to the actual operation requirements, the overall scheme of the sunflower plate control system is determined, and the control strategy of imitating artificial low loss harvesting is designed. To reduce the grain loss in the process of taking the plate and improve the control accuracy of the system on the movement speed and displacement of the key components in the process of taking the plate, a trapezoidal acceleration and deceleration control algorithm is designed as the control algorithm of taking the plate. To verify the working performance of the plate control system, with the absolute error, relative error and total loss rate of the harvest as objectives. The bench and field verification experiments were both carried out. The bench experiment showed that the speed error of the plate parts was not more than 0.028 m/s. In the bench experiments of the device, the maximum positioning error was 1.25 mm, the average relative error is only 0.94 %, and the grain loss rate was not more than 2.26 %. It result showed that the system algorithm was reliable, the positioning accuracy was high, and the taking plate operation can be completed well. The field verification experiment showed that the forward speed of the unit was in the range of 0.4~0.8 m/s, and the total loss rate of harvest was less than 5 %. When the forward speed is 0.6 m/s, the minimum harvest loss rate is 2.32 %, and which indicated the control system meets the requirements of sunflower harvesting operation.

The exposure to extreme temperatures in workplaces involves physical hazards for workers. A poorly acclimated worker may have lower performance and vigilance and may therefore be more exposed to accidents and injuries. Due to the incompatibility of the existing standards implemented in some workplaces and the lack of thermoregulation in many protective equipment, thermal stress remains one of the most frequent physical hazards in many work sectors. However, many of these problems can be overcome with the use of smart textile technologies that enable intelligent thermoregulation in personal protective equipment. Smart textiles can detect, react and adapt to many external stimuli. Interconnected sensors and actuators that interact and react to existing risks can provide the wearer with increased safety, protection and comfort. Thus, the skills of smart protective equipment can contribute to the reduction of errors and the number and severity of accidents in the workplace, and thus promote improved performance, efficiency and productivity.This review provides an overview and opinions of authors on the current state of knowledge on these types of technologies by reviewing and discussing the state of the art of commercially available systems and the advances made in previous research works.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

Personal protective equipment (P PE) rules must be respected and followed to the letter of healthcare professionals in Cameroon to avoid the transmission of infectious diseases. This research proposes solutions to the problems of non-adherence and non-compliance among healthcare workers in Cameroon towards PPE rules. Inadequate access to suitable PPE, discomfort when wearing PPE during poor quality, and a lack of training on correct PPE use are just a few of these obstacles amongst HCWs in Cameroon. Hospitals and healthcare facilities should prioritize offering thorough instruction on PPE use and pinpoint the need to adhere consistently to PPE rules to remove these obstacles. They should also ensure that all healthcare personnel have access to and a sufficient supply of the proper PPE. Through the organization of impromptu visits by surveillance teams to identify areas of support and training, there is a need for assistance from government bodies and public health groups in creating awareness of the security value of PPE use among healthcare professionals. There is a lack of PPE in health care settings in rural areas in Cameroon, thus a need for an adequate supply. Then can we put appropriate PPE policies and practices for HCWs in Cameroon, as they will keep to it.Healthcare professionals in Cameroon must comprehend that following PPE standards protects not just their selves from diseases but also their patients, coworkers, and communities. We are accountable for ensuring everyone's safety and well-being, and adhering to PPE regulations is an essential first step.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The COVID-19 crisis has resulted in a shortage of personal protective equipment (PPE) [1]. COVID-19 is currently the leading cause of death in the United States[2]. Health care providers caring for COVID-19 patients or at high risk of being exposed to the SARS-CoV-2 virus benefit from a face shield to protect against aerosol droplets that could hit the face and minimize the chance of inadvertently touching the face with contaminated hands, and air filtration to filter out aerosolized SARS-CoV-2. Adapting commercially available full-faced snorkel masks has been proposed as an alternative to narrow the gap in PPE [3]. Here we explore a full-faced snorkel mask with commercially available particulate filters.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Safety and health issues are growing concerns in the agricultural sector among farm-workers in South Africa. The current health pandemic arising from the corona virus has thrown these issues into the spotlight, and this study explored the perceived usefulness and perceived ease of using personal protective materials among farm-workers in the banana sector. Using a case study of 10 large farms in the lower south coast of South Africa, we utilized descriptive and inferential analysis to identify the demographic composition of farm-workers in the study area, examine their perception of specific personal protective materials, and determine the relationship between demographic characteristics and perception of personal protective materials. Farm-workers in the study area were found to be predominantly single black males aged between 36-55years, with no more than a primary education, with work experience of between 6-10 years and employed as unskilled farm-labourers. Perceived usefulness (83%) and perceived ease of use (79%) for personal protective materials was high. Respondents gender (p=0.012), marital status (p=0.029), level of education (p=0.035) and farm-work experience (p=0.008) were significant, while their age (p=0.057), population group (p=0.160) and work classification (p=0.203) were not found significant in determining perceived usefulness or perceived ease of use. Our study makes valuable contribution to the existing body of knowledge regarding farm-worker safety issues by exploring perception of personal protective materials.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

Artisanal goldminers in Ghana are exposed to various levels and forms of health, safety and environmental threats. Without the required legislation and regulations, artisanal miners are responsible for their own health and safety at work. Consequently, understanding the probabilities of self-protection at work by artisanal goldminers is crucial. A cross-sectional survey of 500 artisanal goldminers was conducted to examine the probabilities of personal protective equipment use among artisanal goldminers in Ghana. The data was subjected to both descriptive and inferential statistics. Initial findings showed that personal protective equipment use among artisanal miners was 77.4%. Overall, higher probabilities of personal protective equipment use was observed among artisanal goldminers who work in good health and safety conditions as compared to artisanal miners who work in poor health and safety conditions. Also, personal protective equipment use was more probable among the highly educated artisanal goldminers, miners who regularly go for medical screening and the most experienced miners. Additionally, personal protective equipment use was more probable among artisanal miners who work in non-production departments and miners who work in the medium scale subsector. Inversely, personal protective equipment use was less probable among female artisanal miners and miners who earn more monthly income ($174 and above). To increase self-care and safety consciousness in artisanal mining, there is the need for a national occupational health and safety legislation in Ghana. Also, interventions and health promotion campaigns for better occupational conditions in artisanal mining should target and revise the health and safety related workplace programs and conditions

Following the well-known pandemic, declared on 30 January 2020 by the World Health Organi-zation, the request for new global strategies for the prevention and mitigation of the spread of the infection has come to the attention of the scientific community. Nanotechnology has often managed to provide solutions, effective responses, and valid strategies to support the fight against SARS-CoV-2. This work reports a collection of information on nanomaterials that have been used to counter the spread of the SARS-CoV-2 virus. In particular, the objective of this work is to illustrate the strategies that have made it possible to use the particular properties of nanomaterials, for the production of personal protective equipment (DIP) for the defense against the SARS-CoV-2 virus.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Background: The healthcare workers are exposed to dangerous pathogen agents during the outbreak of the new coronavirus COVID-19. To minimize the risk of becoming infected by this virus, healthcare workers need to wear the most appropriate personal protective equipment (PPE). Objective: The objective of this study was to analyze the guidelines that the World Health Organization (WHO) and the Centers for the Disease Control and Prevention (CDC) recommend for the rational use of EPP to protect healthcare workers against the novel coronavirus COVID-19.Methodology: To learn how to effectively protect healthcare workers against the COVID-19, a detailed analysis and comparison of the WHO and CDC guidelines related to the proper use of personal protection equipment (PPE) in different healthcare settings was carried out. Results: The results of this study based on an analysis of PPE recommended by the World Health Organization (WHO) and the Centers for the Disease Control and Prevention (CDC) indicated that the safety and protection of healthcare workers can be maximized if the guidelines suggested by these institutions are followed. In general, the WHO and CDC recommendations based on medical practices are similar, and depending on the healthcare activities and settings where the healthcare workers perform their work, suggest wearing medical/surgical facemasks, respirators, googles and face shields (eye protection), gloves, gowns and aprons. Conclusions: The protection and safety of the healthcare workers can be maximized during the outbreak of COVID-19 by following the WHO and CDC recommendations described in this study. The general guidelines offered by these institutions are similar and based on medical practices.

The ability to express and recognize emotion via facial expressions is well known to change with age. The present study investigated the differences in the facial recognition and facial expression of the elderly (n = 57) and the young (n = 115) and measure how each group uses different facial muscles for each emotion with Facial Action Coding System (FACS). In facial recognition task, the elderly did not recognize facial expressions better than young people and reported stronger feelings of fear and sad from photographs. In making facial expression task, the elderly rated all their facial expressions as stronger than the younger, but in fact, they expressed strong expressions in fear and anger. Furthermore, the elderly used more muscles in the lower face when making facial expressions than younger people. These results help to understand better how the facial recognition and expression of the elderly change, and show that the elderly do not effectively execute the top-down processing concerning facial expression.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The Planetary Roller Screw Mechanisms (PRSMs), alongside Ball Screw Mechanisms (BSMs) and Electromechanical Actuators (EMAs), occupies a pivotal role in advancing the precision and efficiency of various industrial applications, including aerospace, automotive, and high-precision machining tools. Despite their critical advantages such as high load capacity, superior precision, and extended lifespan, the deployment of PRSMs in complex operational conditions reveals a landscape rife with challenges and opportunities for further research. This comprehensive review endeavors to dissect the multifaceted aspects of PRSMs, focusing on their mechanics and dynamics, tribology and thermal behavior, and the paramount importance of reliability and condition monitoring. By synthesizing current research findings, this paper highlights the significant advancements in understanding the static and dynamic characteristics of PRSMs, the intricate interplay between lubrication conditions and wear mechanisms, and the critical role of thermal effects on operational performance. Moreover, it delves into the dynamic models that address the impact of manufacturing imperfections, such as waviness and defects, on the reliability of these mechanisms. Despite the strides made, the review identifies critical gaps in the existing literature, particularly under conditions of extreme temperatures, large deformations, and multifaceted loads, advocating for a holistic approach to research. By proposing integrated thermo-mechanical models and emphasizing the need for empirical validations, this paper outlines a roadmap for future studies aimed at facilitating the development of more robust and reliable PRSMs, capable of meeting the demands of complex operational scenarios and advancing the field of high-precision applications in aerospace, robotics, and beyond.

Objective: There are currently no known treatment methods for ensuring complete recovery from facial nerve damage. Thus, various basic and clinical studies continue to be conducted to achieve this end. As part of this research, autophagy is being investigated for its role in nerve regeneration. Here, we review the existing literature regarding the involvement and signifi-cance of autophagy in facial nerve injury and regeneration. Methods: A comprehensive litera-ture review was conducted to assess the induction and role of autophagy in facial nerve injury and subsequent regeneration. Results: Studies conducted on rats and mice have demonstrated activation of autophagy and expression of related factors in facial and sciatic nerves. Among the most studied of these factors in relation to degeneration and regeneration of facial and sciatic nerves are LC3II/I, PI3K, mTOR, Beclin-1, ATG3, ATG5, ATG7, ATG9, and ATG12. Conclusion: This analysis indicates that autophagy is involved in the process of nerve regeneration follow-ing facial and sciatic nerve damage. Inadequate autophagy induction or failure of autophagy re-sponses can result in regeneration issues after facial or sciatic nerve damage. Animal studies suggest that autophagy plays an important role in facial and sciatic nerve degeneration and re-generation.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

Benefits of baby swimming have been established, but there is limited knowledge about the methodologies used by practitioners. To address this knowledge gap, this study aimed to categorize and classify the equipment and environmental used in baby swimming programs worldwide. A descriptive categorical content analysis approach was employed to analyse videos of baby swimming programs obtained from YouTube. The framework created was validated for interrater reliability, and a pilot study was conducted to classify videos from different countries based on the equipment and environment used. Results indicated that the physical environments observed were pool tanks and swimming pools with and without depth reduction zones, while the equipment used included assistive devices, toys, and clothes. This study represents a significant first step in the development of a comprehensive tool to systematize and characterize the methodologies used in baby swimming programs globally.

Suicide is a public health problem influenced by a variety of biological, psychological, social, and environmental factors. Recognizing the warning signs at each stage is crucial for prevention and helping those at risk. In this context, body awareness, especially interoceptive body awareness, emerges as a potentially relevant and underexplored factor. In this study, binary logistic regression and linear regression analyses were used to examine the relationship between interoceptive body awareness and suicidal orientation in Colombian university students. In addition, the bootstrap technique was used to resample and estimate the distribution of the data. The results support the idea that greater interoceptive awareness may protect against suicidal orientation by improving emotional regulation. An inverse relationship was found between interoceptive awareness and suicidal ideation. These findings are consistent with previous literature on the importance of body awareness for emotional well-being. Further longitudinal research is needed to explore this relationship in depth.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Arboviruses are infections caused by arboviruses that may be either symptomatic or asymptomatic, according to individuals' resistance and immune response, which dietary patterns can influence. Thus, this study aimed to investigate the possible association between the occurrence of clinical manifestations of arboviruses and the dietary pattern of the population studied. The study was conducted in a rural population in the metropolitan area of Belém, Pará State, Brazil. The sampling consisted of 95 individuals during a febrile outbreak. Two investigations were conducted: clinical-epidemiological-dietary and laboratory investigation based on blood samples taken for arbovirus analysis. Out of the 95 individuals studied, more than half (57.89%) showed clinical manifestations. Following the laboratory serology (HI and IgM ELISA) analyses, viral isolation in C6/36 cells, and viral genome detection (RT-qPCR), the final diagnosis of the cases was 47.37% Oropouche Fever, 2.11% Oropouche Fever and Chikungunya Fever, and 1.05% Mayaro Fever. Regarding dietary pattern, as for the comparison analyses, statistical significance was observed between dietary pattern and classification regarding the presence of symptoms (p<0.05); after the correspondence analysis, symptomatic cases were more associated with a bad dietary pattern, while asymptomatic cases were more associated with a good dietary pattern.

One of the most crucial elements in deeply understanding humans on a psychological level is manifested through facial expressions. The analysis of a human behavior can be informed by their facial expressions, making it essential to employ indicators such as expression (Expr), valence-arousal (VA), and action units (AU). In this paper, we introduce the method proposed in the Challenge of the 6th Workshop and Competition on Affective Behavior Analysis in-the-wild (ABAW) at CVPR 2024. Our proposed method utilizes the multi-modal Aff-wild2 dataset, which is splitted into spatial and audio modalities. For the spatial data, we extract features using a SimMiM model that was pre-trained on a diverse set of facial expression data. For the audio data, we extract features using a WAV2VEC model. To fusion the extracted spatial and audio features, we employed the cascaded cross-attention mechanism of a transformer.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

Facial expressions play a key role in interpersonal communication when it comes to negotiating our emotions and intentions, as well as interpreting those of others. Research has shown that we can connect to other people better when we exhibit signs of empathy and facial mimicry. However, the relationship between empathy and facial mimicry is still debated. Among the factors contributing to the difference in results across existing studies is the use of different instruments for measuring both empathy and facial mimicry, as well as often ignoring the differences across various demographic groups. This study first looks at the differences in empathetic abilities of people across different demographic groups based on gender, ethnicity and age. The empathetic ability is measured based on the Empathy Quotient capturing a balanced representation of both emotional and cognitive empathy. Using statistical and machine learning methods, the study then investigates the correlation between the empathetic ability and facial mimicry of subjects in response to images portraying different emotions displayed on a computer screen. Unlike the existing studies measuring facial mimicry using electromyography, this study employs a technology detecting facial expressions based on video capture and deep learning. This choice was made in the context of increased online communication during and post the COVID-19 pandemic. The results of this study confirm the previously reported difference in the empathetic ability between females and males. However, no significant difference in the empathetic ability was found across different age and ethnic groups. Furthermore, no strong correlation was found between empathy and facial reactions to faces portraying different emotions shown on a computer screen. Overall, the results of this study can be used to inform the design of online communication technologies and tools for training empathy team leaders, educators, social, and health care providers.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Background: The purpuse was to investigate the influence induced by magnesium chloride (MgCl2) and zinc gluconate (ZnG) supplementation on liver and kidney injuries experimentally-induced with acetaminophen (AAPh) and potentiated by ciprofloxacin addition in rats. Material and methods: The experiment was performed on 5 animals groups: group 1 – control, treated for 6 weeks with normal saline, 1mL/kg; group 2 – AAPh, treated for 6 weeks with AAPh, 100 mg/ kg/day; group 3 – AAPh+C, treated AAPh 100 mg/kg/ day for 6 weeks and ciprofloxacin, 50mg /kg/day, only in the last 14 days of the experiment; group 4 – AAPh+C+Mg, with the same treatment as group 3, but, and in the last 14 days, MgCl2 10 mg/ kg/day was added; group 5 – AAPh+C+Zn, with the same treatment as group 3, but, and in the last 14 days, zinc gluconate (ZnG),10 mg/kg/day was added. All administrations were performed by oral gavage. At the end of the experiment, the animals were sacrificed and blood samples were collected for biochemistry examinations. Results: Treatment with AAPh for 6 weeks determined an alteration of the liver function (increases in alanine aminotransferase, aspartate aminotransferase, lactic dehydrogenase and, and gamma-glutamyl transferase) and of renal function (increases in serum urea and creatinine) (P < 0.001 group 2 vs. group 1 for all mentioned parameters). Also, the antioxidant defense capacity was impaired in group 2 vs. group 1 (superoxide dismutase and glutathione peroxidase activity decreased in group 2 vs. group 1, 0.001 < P < 0.01, respectively 0.01 < P < 0.05). The addition of ciprofloxacin, 50 mg/kg/day during the last 14 days resulted in further increases in alkaline phosphatase, alanine aminotransferase, aspartate aminotransferase, urea and creatinine (0.01 < P < 0.05, group 3 vs. group 2). MgCl2 provided a slight protection against liver enzymes increase and a more pronounced protection against the increase in serum urea and creatinine (0.001 < P < 0.01 group 4 vs. group 3). MgCl2 provided a slight protection against the decrease in superoxide dismutase (0.01 < P < 0.05 group 4 vs. group 3), but not against decrease of glutathione peroxidase. The improvement of mentioned parameters could also be seen in case of ZnG, to a higher extent especially in the case of alanine aminotransferase and lactic dehydrogenase (0.01 < P < 0.05 group 5 vs. group 4). Conclusions: This study represents a furthermore proof for beneficial effect of magnesium and zinc salts against toxicity induced by different agents, including antibacterials added to the analgesic and antipyretic acetaminophen; the protection is proven on the liver and kidney’s function; the antioxidant profile improvement has a key role, especially in case of zinc gluconate.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

Background: Metastatic tumors to the oro-facial tissues are rare, with an incidence ranging between 1% and 8% of all oral malignant tumors. Generally reported with a peak of incidence in the 5th–7th decades, but possibly occurring at any age, metastases may represent the first sign of an occult cancer or manifest in patient with an already known history of a primary carcinoma, mostly from the lungs, kidney, prostate, and colon-rectum in males, or uterus, breast, lung, and ovary in females. In the oro-facial tissues the sites mostly involved are the oral mucosa, gingiva/jawbones, tongue, and the salivary glands. Methods: A systemic Review of the literature on the oro-facial metastases from Renal Cell Carcinoma has been conducted by searching the most used databases, also focusing the attention on the Clear Cell histological variant, representing the most frequent one. Results: Among the 160 analyzed studies, 211 cases of oral metastases of renal cancer were found (148 in males, 70.1%; 63 in females, 29.8%), with an average age of 59.8 years. In almost 40% of cases, metastasis represented the first clinical manifestation of the primary tumor and 122 were histologically diagnosed as ccRCCs (57.8%). The tongue was involved in most of the cases (26% - 55 cases), followed by mandible (18.9% - 40 cases), gingiva (18.4% - 39 cases), maxilla (10.9% - 23 cases), parotid gland (10.4% - 22 cases), buccal mucosa (5.2% - 11 cases), lips (3.3% - 7 cases), hard palate (2.8% - 6 cases), soft palate, masticatory space and submandibular gland (0.9% - 2 cases), lymph nodes, tonsil and oral floor (0.4% - 1 case). Among the 122 ccRCCs (84 were males, 68.8 %; 38 females, 31.1%), with an average age of 60.8 years and representing in 33.6% the first clinical manifestation, the tongue remained the most involved site (25.4% - 31 cases), followed by the gingiva (17.2% - 21 cases), parotid gland (13,1% - 16 cases), mandibular bone (12.2% - 15 cases), maxillary bone (11.4% - 14 cases), buccal mucosa and lips (4.9% - 6 cases), hard palate (4% - 5 cases), submandibular gland and soft palate (1.6% - 2 cases), lymph nodes, tonsil, oral floor and masticatory space (0.8%. 1 case). The clinical presentation in soft tissues was represented by a fast-growing exophytic mass, sometimes accompanied by pain. Instead inn bone appeared as radiolucent lesions, with ill-defined borders and cortical erosion. Conclusions: Our data focus the attention on the incidence of Renal cancer Metastases in the oro-facial tissues. Their early identification surely represents a diagnostic challenge, especially when the clinical work-up is limited to the cervico-facial region. Nevertheless, early diagnosis and recently introduced adjuvant therapies may represent the key for better outcomes. Therefore, general guidelines about clinical and radiological identification of oro-facial potentially malignant lesions should be part of the cultural background of any dentists.

Detection and measurement of pain are crucial in designing effective pain management interventions to alleviate suffering and prevent functional decline in the medical domain. Traditional methods of pain identification rely on verbal patient reports or observable signs, which can be imprecise or subjective due to variability in patient self-assessments. Hence, there is a pressing need for automated methods to standardize pain measurement procedures. This paper proposes a novel facial expression-based automated pain assessment system as a behavioral indicator for pain evaluation. Our system integrates a fusion structure comprising Convolutional Neural Networks (CNNs) and Tensor-based extended Quantitative Expression Descriptors Analysis (TXQEDA). This innovative approach allows for joint learning of robust pain-related facial expression features from raw facial images, combining RGB appearance with shape-based latent representation. We extensively evaluated our proposed model using the UNBC-McMaster dataset for pain classification and intensity estimation. Our results demonstrate the efficacy of the proposed technique, achieving an impressive accuracy of 99.10% for pain level classification. Furthermore, our system excels in pain intensity estimation, showcasing its potential to provide precise and reliable assessments of pain severity. Overall, our research underscores the importance of automated pain assessment systems in improving patient care and clinical outcomes. By leveraging advanced deep learning techniques and fusion strategies, our proposed model offers a promising approach for standardizing pain measurement procedures and enhancing the quality of pain management interventions.

At present, the health systems of many countries face complex challenges even if their priority objectives remain the same - to provide sustainable health systems at the current and the prognostic demographic changes and requirements in a health system. The quality and the efficiency of healthcare delivery and their mutual conformity have been brought to public attention. Similarly, the quality and the efficiency of an entire process depends on the instrumentation and its procurement that represents a significant economic and procedural issue in the healthcare systems for a long time. Many reports of the public procurement processes and research studies declare this fact. The primary aim of this study is to evaluate the public procurement efficiency in the health system by means of the valuation approach, or savings’ estimates that are achieved by the public procurement. The savings were defined as a percentage difference between the estimated and the final contract price. The secondary objective is to examine an influence of selected variables on a creation of savings in the public procurement process by means of a regression analysis. The researched variables are as follows: time, method, procurement, NUTS level of procurement, Common Procurement Vocabulary Code, number of offers. The analysis results showed interesting findings. The number of offers has a significantly positive impact on the savings. It means that if the number of offers increases by one unit, the savings will increase by 15.6%. Also, time variable (year) has a positive impact on the savings. Consequently, it may be assumed that the public procurement process is improving from a time perspective. It may be partially caused by the fact that a new public procurement legislative has been valid since 2015. The NUTS level has also an impact on the savings in relation to the public procurement. The public procurements which took place at the level of a state were more beneficial as the public procurements at the regional level. Also, the procurement method was statistically significant parameter of a regression analysis. The competition actions together with a negotiation process created higher savings in comparison to tenders. In case of the CPV codes, the most significant savings were achieved in the group of ‘various medicinal products’. The study’s results provide a valuable knowledge for the creators of policies and a realization of the national strategic plans within the health system. Also, these results support a creation of national and international benchmarks in this area and a networking of international partnerships in the area of a public procurement that focus on a development of methodologies and comparative platforms creation.

Sanitisation has become a major component of everyday life, with emphasis on the hands and surfaces. The face remains unsanitised due to the lack of an acceptable sanitiser. The use of masks has been mandated to reduce the spread of the pathogens by covering the face, however, there remain issues with the use of personal protective equipment. The face remains a harbour for upper respiratory tract infections, with constant deposition of microbes. By reducing microbial load, the risk of both infection and severity are reduced. HOCl has proven antimicrobial and anti-inflammatory activity, including efficacy against SARS-CoV-2. A facial sanitiser, alongside hand sanitisers and masks, improves protection against SARS-CoV-2. The advantages of regular sanitising of the face and mask include reduced level of microbial contamination, risk of biofilm formation, and respiratory tract and skin infections. HOCl was reviewed as a face and mask sanitiser, concluding that it was an ideal product.

The issue of equipment layout in multi-floor satellites consists of two primary parts: allocating the equipment to the satellite's layers and placing the equipment in each layer individually. In reviewing the past literature in this field, firstly, the issue of assigning equipment to layers is observed in a few articles and next in the layout part, the non-overlapping constraint has always been a challenge, particularly for components that do not have a circular cross-section. In addition to presenting a heuristic method for allocating equipment to different layers of the satellite, this article presents a robust flexible programming model (RFPM) for the placement of equipment at different layers, taking into account the inherent flexibility of the equipment in placement and the subject of uncertainty. This model is based on the existing uncertainty between the distances of cuboid equipment which has not been addressed in any of the previous research, and by comparing its outputs with cases from past studies, it demonstrates a significantly higher efficiency in placing the equipment and meeting the limit of non-overlapping constraints between the equipment. Finally, it would be possible to reduce the design time in the conceptual and preparatory stages, as well as the satellite's overall size, while still satisfying other constraints like stability and thermal limitations, moments of inertia and centre of gravity.

Nurses have experienced several psychological and work-related issues during the COVID-19 pandemic including pandemic burnout and job burnout. The aim of the study was to examine the impact of social support and resilience on COVID-19 pandemic burnout and job burnout among nurses. We conducted a cross-sectional study in Greece. Study population included 963 nurses. We measured social support, resilience, COVID-19 pandemic burnout, and job burnout with the Multidimensional Scale of Perceived Social Support, Brief Resilience Scale, COVID-19 burnout scale, and single item burnout measure respectively. Nurses received high levels of social support, while their resilience was moderate. Additionally, nurses experienced moderate levels of COVID-19 burnout and job burnout. Increased social support (adjusted beta = -0.075, 95% CI = -0.125 to -0.024) and increased resilience (adjusted beta = -0.399, 95% CI = -0.491 to -0.308) were associated with reduced COVID-19 pandemic burnout. We found a negative relationship between social support and job burnout (adjusted beta = -0.263, 95% CI = -0.405 to -0.121). A similar negative relationship was found between resilience and job burnout (adjusted beta = -0.529, 95% CI = -0.785 to -0.272). Social support and resilience can act as protective factors against COVID-19 pandemic burnout and job burnout among nurses. Policy makers should develop and implement appropriate strategies to improve nurses’ social support and resilience since they are the backbone of healthcare systems worldwide.

Facial acne is a prevalent dermatological condition regularly observed in the general population. This study introduces a novel deep learning model for facial acne segmentation utilizing a semi-supervised learning method known as bidirectional copy-paste, which synthesizes images by interchanging foreground and background parts between labeled and unlabeled images during the training phase. To overcome the lower performance observed in the labeled image training part compared to the previous methods, a new framework was devised to directly compute the training loss based on labeled images. The effectiveness of the proposed method was evaluated against previous semi-supervised learning methods using images cropped from facial images at acne sites. The proposed method achieved a Dice score of 0.5205 in experiments utilizing only 3% of labels, marking an improvement of 0.0151 to 0.0473 Dice score over previous methods. The proposed semi-supervised learning approach for facial acne segmentation demonstrates improvement in performance, offering a novel direction for future acne analysis.

Emojis are colorful ideograms resembling stylized faces commonly used for expressing emotions in instant messaging, in social network sites and in email communication. Notwithstanding their increasing and pervasive use in electronic communication, they are not much investigated in terms of their psychological properties and communicative efficacy. Here we presented 112 different human facial expressions and emojis (expressing neutrality, joy, surprise, sadness, anger, fear and disgust) to a group of 96 female and male university students engaged in the recognition of their emotional meaning. Both Analysis of Variance and Wilcoxon tests showed that men were significantly better than women at recognizing emojis (especially negative ones) while women were better than men at recognizing human facial expressions. Quite interestingly, men were better at recognizing emojis than human facial expressions per se. These findings are in line with more recent evidences suggesting how men may be more competent and inclined to use emojis to express their emotions in messaging (especially sarcasm, tease and love) than previously thought. Finally, the data indicate how emojis are less ambiguous than facial expressions (except for neutral and surprise emotions), possibly because of the limited number of fine-grained details, and the lack of morphological features conveying facial identity.

Facial expression has lots of applications in human-computer interaction. Although feature extraction and selection have been well studied, the specificity of each expression variation is not fully explored in state-of-the-art works. In this work, the problem of multiclass expression recognition is converted into triplet-wise expression recognition. For each expression triplet, a new feature optimization model based on Action Unit (AU) weighting and patch weight optimization is proposed to represent the specificity of the expression triplet. Sparse representation based approach is then proposed to detect the active AUs of testing sample for better generalization. The algorithm achieved competitive accuracies of 89.67% and 94.09% for Jaffe and CK+ databases, respectively. Better cross-database performance has also been observed.

The Industrial Internet of things (IIoT) enabled smart system has entered into a golden era of rapid technology growth. IIoT is a concept to make every system interrelated such that they are able to collect and transfer data over a wireless network without human intervention. In this paper, we discuss the development of an IoT enabled system to monitor the vibration signature of equipment as part of prognosis and availability management system (P&AM) that serves to prevent unplanned operation downtime and catastrophic failure of a whole system. In order to simply the complexity of processing video content and performing inference, the Intel OpenVINO platform was selected because of it’s simplicity, portability across Intel AI processors, performance and comprehensiveness of it’s analytical and diagnostics capabilities that can be tested in Intel’s DevCloud. The IIoT system consists of a High Performance Computing (HPC) platform based on Intel’s Xeon processors and Movidius AI accelerator, Intel’s OpenVINO toolkit for AI, a Regul high performance programmable controller capturing vibration data through sensors and a low-latency network connection. Notifications of anomalies are sent to a smartphone. This paper reveals an approach for the features extraction and selection, known as feature engineering, of the equipment component we want to protect. Feature engineering is the first step for the P&AM of these components and extends to the whole system. The broader aim of this paper is to help technical leaders at the exploring or experimenting stages of their AI framework to learn the concepts of implementing algorithms using datasets that have real value to their companies. Datasets generated and referred to in this paper were generated by simulation under various material failure scenarios.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

With the increasing utilization of intelligent mobile devices for online inspection of electrical equipment in smart grids, the limited computing power and storage capacity of these devices pose challenges for deploying large algorithm models and it’s hard to obtain a substantial number of images of electrical equipment in public. In this paper, we propose a novel distillation method that compresses the knowledge of teacher networks into a compact few-shot classification network, employing a global and local knowledge distillation strategy. Central to our method is exploiting the global and local relationship between the features exacted by the backbone of the teacher network and student network. We compare our method with recent state-of-the-art (SOTA) methods on three public datasets and achieve superior performance. Additionally, we contribute a new dataset, namely EEI-100, which is specifically designed for classification of electrical equipment. We validate our method on this dataset and demonstrate its exceptional prediction accuracy of 94.12% when utilizing only 5-shot images.

Proposed as a response to the increasing global need for environmental protection, a green port balances economic vibrancy and environmental protection. However, because exhaust emissions (e.g., CO2 or sulfide) are difficult to monitor in and around ports, data on such emissions are often incomplete, which hinders research on this topic. To remedy this problem, this study aimed to formulate a method for collecting CO2 emissions data at their source; this method was applied to collect real-world operating data from a large container-handling company in Taiwan. Specifically, to account for undesirable outputs, we formulated a method that combines (1) data envelopment analysis based on a modified slack-based measure and (2) a multichoice goal programming approach. We found that rubber-tired gantry cranes are the greenest and should be used. Our findings aid port managers in selecting port equipment that best balances between environmental protection and profitability.

Polyetheretherketone (PEEK) in the last few years emerged as an exceedingly promising material for craniofacial defect, due to its biocompatibility and mechanical properties. However, its utilization remains controversial due to its inertness and low osteoinductivity. This study aimed to investigate the postoperative outcomes of patients undergoing maxillo-facial and neurosurgical procedures with PEEK implants. The focus is on evaluating bone regrowth on the surface and edges of the implant, periosteal reactions, and implant positioning. A retrospective analysis of 12 maxillo-facial surgery patients and 10 neurosurgery patients who received PEEK implants was conducted. CT scans performed at least one-year post-operation, were examined for bone regrowth, periosteal reactions, and implant positioning. In maxillo-facial cases, the analysis included mandibular angle and fronto-orbital reconstruction, while neurosurgical cases involved cranioplasty. In maxillofacial surgery, 11 out of 12 patients showed radiological evidence of bone regrowth around PEEK implants, with favorable outcomes observed in craniofacial reconstruction. In neurosurgery, 9 out of 10 patients exhibited minimal or none bone regrowth, while one case demonstrated notable bone regeneration beneath the PEEK implant interface. The study highlights the importance of implant design and patient-specific factors in achieving successful outcomes, providing valuable insights for future implant-based procedures.

There is a growing consensus that culture influences the perception of facial expressions of emotion. However, little is known about whether and how culture shapes the production of emotional facial expressions, and even less so about whether culture differentially shapes the production of posed versus spontaneous expressions. Drawing on prior work on cultural differences in emotional communication, we tested the prediction that people from the Netherlands (a historically heterogeneous culture where people are prone to low-context communication) produce facial expressions that are more distinct across emotions compared to people from China (a historically homogeneous culture where people are prone to high-context communication). Furthermore, we examined whether the degree of distinctiveness varies across posed and spontaneous expressions. Dutch and Chinese participants were instructed to either pose facial expressions of anger and disgust, or to share autobiographical events that elicited spontaneous expressions of anger or disgust. Using the complementary approaches of supervised machine learning and information-theoretic analysis of facial muscle movements, we show that posed and spontaneous facial expressions of anger and disgust were more distinct when produced by Dutch compared to Chinese participants. These findings shed new light on the role of culture in emotional communication by demonstrating, for the first time, effects on the distinctiveness of production of facial expressions.

Background. The Weekly Mortality Cycle among CoViD-19 patients has been studied.Methods. Mortality data obtained from the 'Worldometer' website were analyzed with a comparison of absolute values, percentages, and p-value. Results. For patients suffering from CoViD-19, the most favorable or the safest days of the week were Sundays and Mondays. Conclusion. The weekly cycle with decreased mortality on Sundays and Mondays is a unique phenomenon observed among victims of CoViD-19. Presumably the decreased mortality on certain days of the week related to the optimized therapeutic protocols used on the "safest days".

Accurate and robust deep learning models for facial expression recognition are challenging to achieve, given the diversity of human faces and variations in images, including different facial poses and lighting conditions. In this work, we proposed a clock-driven convolutional Spiking Neural Network (SNN) and STDP fine-tune architecture, meticulously calibrated its hyperpa-rameters, and experimented with various optimization methods. The best model resulted was trained and evaluated on the Fer2013 and FER+ database, obtaining an accuracy of 61.87% and 79.97% without requiring auxiliary training data or face registration. To our best knowledge, the proposed SNN achieved comparable accuracy to CNNs of similar depth and possessed advantages of low energy consumption and high computational efficiency. The computational efficiency of the proposed SNN is approximately three times that of CNNs. Along with this, we introduced the very recent cumulative spike guided encoder visualization technique and revealed the strong encoding capability of the proposed SNN.

In the context of artificial intelligence's pervasive integration across sectors, the rigorous examination of methodologies used in constructing mathematical models is imperative. This study delves into facial recognition models, particularly in their ability to extract features such as age. We address the prevalent practice of training models with unbalanced datasets and its implications for model performance and bias introduction. Utilizing 27,305 facial images, we investigate the influence of dataset imbalance on age prediction based on ethnicity. Employing preprocessing and oversampling techniques, we equalize sample sizes across ethnicities. A Convolutional Neural Network trained on the balanced dataset serves as our baseline, while three additional models undergo training with a 50% sample size reduction for each group to assess accuracy degradation. Our findings reveal a notable decline in accuracy for ethnic groups with reduced representation. The Asian group experiences a 67.94% accuracy deterioration, followed by a 51.60% drop for the Black group, and a 38.46% decline for the White group. These results underscore the sensitivity of certain ethnic groups to underrepresentation, highlighting the nuanced impact on age prediction accuracy. While a 50% reduction in representation does not uniformly result in a 50% accuracy decline, it unquestionably influences predictive accuracy for affected groups.

Facial emotion detection is a challenging task that deals with emotion recognition. It has applications in various domains, such as behavior analysis, surveillance systems and human-computer interaction (HCI). Numerous studies have been implemented to detect emotions, including classical machine learning algorithms and advanced deep learning algorithms. For the machine learning algorithm, the hand-crafted feature needs to be extracted, which is a tiring task and requires human effort. Whereas in deep learning models, automated feature extraction is employed from samples. Therefore, in this study, we have proposed a novel and efficient deep learning model based on Neural Architecture Search Network utilizing superior artificial networks such as RNN and child networks. We performed the training utilizing the FER 2013 dataset comprising seven classes: happy, angry, neutral, sad, surprise, fear, and disgust. Furthermore, we analyzed the robustness of the proposed model on CK+ datasets and comparing with existing techniques. Due to the implication of reinforcement learning in the network, most representative features are extracted from the sample network. It extracts all key features without losing the key information. Our proposed model is based on one stage classifier and performs efficient classification. Our technique outperformed the existing models attaining an accuracy of 98.14%, recall of 97.57%, and precision of 97.84%.

The emergence of new methodologies and tools for digitizing objects belonging to the Cultural Heritage (CH) changed the paradigms adopted so far. Traditionally, the process to acquire artifacts required specialized and often costly equipment tailored to specific purposes. However, the development of more generalized, adaptable, and affordable tools led to novel approaches. This manuscript provides a glimpse into the evolving landscape of custom-made tools for digital documentation, both hardware and software, and their transformative impact on the digitization techniques, built to meet requirements of specific case studies, including ancient drawings, manuscripts, paintings, and museum objects. The advent of self-built instruments has revolutionized the way professionals work today, by leveraging a new generation of low-cost, adaptable gears, leading to unprecedented flexibility and efficiency, while facilitating the capture of high-quality digital representations of objects with minimal damage and preserving their integrity. The outcomes of instruments and tools specifically produced for the contexts described in this paper highlight their potential for promoting interdisciplinary collaboration, facilitating scholarly research, enhancing conservation efforts, and fostering cultural exchange. Ultimately, this research contributes to illustrate how custom software, in combination with recent devices such as smartphones and 3D printers, underscores the importance of adopting these innovative approaches to generate an ecosystem of tools and methods able to preserve, document, and promote the richness of our collective past for future generations.

In the realm of smart manufacturing, equipment plays a pivotal role, impacting the efficiency and quality of production. Ensuring equipment availability and optimal performance is crucial, necessitating effective maintenance strategies. This paper addresses the complexities of smart device maintenance, which often involves collaboration between multiple entities like device owners, manufacturers, suppliers, and external maintenance services. To enhance this cooperative maintenance, we propose a novel maintenance system based on permissioned blockchain technology, offering superior security and reliability compared to conventional cloud-based platforms. Our contributions include developing an integrated maintenance system framework for smart manufacturing, which facilitates interactions among diverse stakeholders. Additionally, we have developed a prototype of this maintenance system, serving as a practical model for real-world application. Our research primarily demonstrates the practicality and advantages of using permissioned blockchain for maintenance systems in the manufacturing sector, paving the way for more secure, efficient, and collaborative maintenance practices.

The airport ground handling services (AGHS) equipment supplier selection problem involves a safety guarantee on the part of the AGHS company that carries out the daily work. AGHS company can prevent aircraft damage and delays in airlines schedules, and ensure reliable and high-quality ground handling service. In our research, we developed an AGHS equipment supplier selection model based on the analytic hierarchy process and an AHP weighted fuzzy linear programming approach, and we solved the AGHS equipment supplier’s selection problem. The main objective of this article is to create an AHP and AHP-FLP decision model in order to help the AGHS company authorities select the best AGHS equipment supplier. The practical application in AGHS equipment supplier selection decisions can be interpreted as demonstrating that the proposed model provides knowledge and practical value for the AGHS industry.

Microalgal harvesting is one of the most challenging processes in the development of algal research and development. Several methods, such as centrifugation, flocculation, and filtration, are available at the laboratory scale. However, the requirement of expensive pieces of equipment and the possibility of biomass contamination are recurring gaps that hinder the development of microalgae I+D in different parts of the world. Recently, the electroflotation has been proved as a suitable method for the harvesting of different species of microalgae and cyanobacteria. To this day, there are no companies that sell laboratory-scale electroflotation equipment; this is mainly due to the gap in the knowledge on which factors (time, mixing rate, number of electrodes, and others) will affect the efficiency of concentration without reducing the biomass quality. This paper aims to build an innovative low-cost electroflotation system under 300 USD with cheap and resistant materials. To achieve our goal, we test the interaction of three variables (time, mixing rate, and amount of electrodes) were evaluated. Results showed that an efficiency closer to 100% could be achieved under 20 minutes using >10 electrodes and 150 rpm. We hope this innovative approach can be used by different researchers to improve our knowledge of the concentration and harvesting of algae and cyanobacteria.

The pervasive presence of atmospheric pollution, particularly polycyclic aromatic hydrocarbons such as 7,12-dimethylbenz(a)anthracene, instigates aberrant cellular and tissue conditions, precipitating oxidative damage and inflammatory cascades conducive to the onset of cancer, notably mammary cancer. Given the hepatic metabolism of 7,12-dimethylbenz(a)anthracene, the imperative of employing natural antioxidants becomes apparent. In this study, we delve into the antioxidant and hepato-protective properties of Pistacia lentiscus against 7,12-dimethylbenz(a)anthracene-induced toxicity, alongside exploring its potential anticancer attributes. Our investigations unveil Pistacia lentiscus's anti-proliferative efficacy against human breast cancer cell lines. Notably, 7,12-dimethylbenz(a)anthracene-intoxication escalates body weight, disrupts lipid profiles, and incites serum oxidative damage. Concurrently, hepatic and renal oxidative stress ensue, accompanied by heightened antioxidant enzyme activity in the 7,12-dimethylbenz(a)anthracene-exposed-group compared to controls (p&lt;0.05). Nonetheless, Pistacia lentiscus co-administration rectifies biochemical imbalances, significantly attenuates oxidative stress aberrations, and augments antioxidant enzyme responses (p&lt;0.05). Importantly, histological analysis evinces Pistacia lentiscus's shielding effect against 7,12-dimethylbenz(a)anthracene induced hepatocyte injury and steatosis. Our findings underscore Pistacia lentiscus's robust anti-proliferative, antioxidant, and hepato-protective capacities, mitigating metabolic disturbances, oxidative stress propagation in liver and kidney functions, and potential histological alterations, thereby impeding 7,12-dimethylbenz(a)anthracene-induced mammary cancer initiation. We posit that Pistacia lentiscus may serve as a prophylactic agent against breast cancer instigated by this carcinogen.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

The Covid-19 pandemic spreads in waves for a year and a half, despite significant worldwide efforts, the development of biochemical diagnostic methods and population vaccination. One of the reasons for the infection spread is the impossibility of early disease detection through biochemical diagnostics, since biochemical processes slowly develop in a body. At the same time, well known that behavioral characteristics of a person, measured based on reflex movements, are capable for inertialess assessment of psychophysiological parameters. Vibraimage technology is the method of head micromovements video processing by inter-frame difference accumulation and converting spatial and temporal characteristics of the inter-frame difference into behavioral and psychophysiological parameters. Here we shown that behavioral parameters measured by vibraimage changed during COVID-19 infection. The identification of changes signs in behavioral parameters detected by AI trained on patients and controls. The best diagnostic accuracy (higher 94%) obtained using instantaneous values of behavioral parameters measured with the following vibraimage settings: 10Hz frequency of basic measurements; 25 inter-frame difference accumulations and averaging the diagnostic results over period of at least 5 seconds. COVID-19 diagnoses by behavioral parameters showed earlier (5-7 days) detection of the disease compared to symptoms and positive results of biochemical RT-PCR testing. Proposed method for COVID-19 diagnosis indicates infected persons within 5 seconds video processing using standard television cameras (web, IP) and computers, allows mass testing/selftesting and will stop the pandemic spread. We assume that head micromovements analysis for diagnosis of various diseases is possible not only with the help of vibraimage technology. Further research of human head micromovement analysis will help stop the COVID-19 pandemic and will contribute to the development of new contactless and environmentally friendly methods for early diagnosis of diseases.

Single-level Principal Components Analysis (PCA) and multi-level PCA (mPCA) methods are applied here to a set of (2D frontal) facial images from a group of 80 Finnish subjects (34 male; 46 female) with two different facial expressions (smiling and neutral) per subject. Inspection of eigenvalues gives insight into the importance of different factors affecting shapes, including: biological sex, facial expression (neutral versus smiling), and all other variations. Biological sex and facial expression are shown to be reflected in those components at appropriate levels of the mPCA model. Dynamic 3D shape data for all phases of a smile made up a second dataset sampled from 60 adult British subjects (31 male; 29 female). Modes of variation reflected the act of smiling at the correct level of the mPCA model. Seven phases of the dynamic smiles are identified: rest pre-smile, onset 1 (acceleration), onset 2 (deceleration), apex, offset 1 (acceleration), offset 2 (deceleration), and rest post-smile. A clear cycle is observed in standardized scores at an appropriate level for mPCA and in single-level PCA. mPCA can be used to study static shapes and images, as well as dynamic changes in shape. It gave us much insight into the question “what’s in a smile?”

The onset of the Coronavirus 2019 (COVID-19) pandemic has challenged the worldwide healthcare sector, including dentistry. The highly infectious nature of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus and risk of transmission through aerosol generating procedures has profoundly impacted the delivery of dental care services globally for months causing prioritization of critical dental needs and suspension of routine dental procedures. As dental practices with strengthened infection control strategies and preventive measures are re-opening in the “new normal” period, it is the responsibility of healthcare professionals to constantly analyze new data and limit the spread of COVID-19 in dental care settings. With the new variants of SARS-CoV-2 rapidly emerging in different geographic locations, a definite need to comply more than ever with the rigorous public health measures to mitigate COVID -19 transmission exists. The aim of this article is to provide dental clinicians with essential information regarding both the spread of SARS-CoV-2 virus and protective measures against COVID-19 transmission in dental facilities. By compiling guidance and standard protocols recommended by credible national and international organizations, this article serves as an aid to navigating through this unprecedented time with ease. Much to learn about COVID-19 exists and because of constant ongoing research, we are not aware of all of the newly found information. However, in this paper, we reviewed the available literature recommended for the best current practices that must be taken for a dental office to function safely and successfully.

Previous studies have indicated that facial expressions can serve as an objective evaluation method for hedonics (overall pleasure) of food and beverages. In this study, we aimed to validate the findings of our previous research, which demonstrated that facial expressions induced by tastants can predict the perceived hedonic ratings of these tastants. Facial expressions of 29 female participants (aged 18-55 years) were recorded using a digital camera while they consumed 12 different concentrations of solutions representing five basic tastes. The facial expressions were then analyzed using the widely-used facial expression analysis application, FaceReader, to identify seven emotions (surprise, happiness, scare, neutral, disgust, sadness, and anger) with scores ranging from 0 to 1. Participants also rated the hedonics of each solution on a scale from -5 (extremely unpleasant) to +5 (extremely pleasant). A multiple linear regression analysis was conducted to develop a formula to predict perceived hedonic ratings. The formula's applicability was tested by analyzing emotion scores for 11 additional taste solutions consumed by 20 other participants. The predicted hedonic ratings demonstrated good correlation and concordance with the perceived ratings, supporting the validity of our previous findings using different software and taste stimuli among diverse participants.

Animal welfare is not only an ethically important consideration in good animal husbandry, but can also have a significant effect on an animal’s productivity. The aim of this paper is to show that a reduction in animal welfare, in the form of increased stress, can be identified in pigs from frontal images of the animals. We train a Convolutional Neural Network (CNN) using a leave-one-out design and show that it is able to discriminate between stressed and unstressed pigs with an accuracy of >90% in unseen animals. Grad-CAM is used to identify the animal regions used, and these support those used in manual assessments such as the Pig Grimace Scale. This innovative work paves the way for further work examining both positive and negative welfare states with a view to the development of an automated system that can be used in precision livestock farming to improve animal welfare.

We live in extraordinary times, where COVID-19 pandemic has brought the whole world to a screeching halt. Tensions and contradictions that surround the pandemic ridden world include the availability, and the lack thereof, various facial protection measures to mitigate the viral spread. Here, we comprehensively explore the different type of facial protection measures, including masks, needed both for the pubic and the health care workers (HCW). We discuss the anatomy, the critical issues of disinfection and reusability of masks, the alternative equipment available for the protection of the facial region from airborne diseases, such as face shields and powered air purifying respirators (PAPR), and the skin-health impact of prolonged wearing of facial protection by HCW. Clearly, facial protection, either in the form of masks or alternates, appears to have mitigated the pandemic as seen from the minimal COVID-19 spread in countries where public mask wearing is strictly enforced. On the contrary, the healthcare systems, that appear to have been unprepared for emergencies of this nature, should be appropriately geared to handle the imbalance of supply and demand of personal protective equipment including face masks. These are two crucial lessons we can learn from this tragic experience.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

In order to reveal the mechanism and influencing factors of high pressure jet cavitation of nozzle in submerged environment, this study focused on the evolutionary process of cavitation bubbles and combined finite volume method and mixed multi-phase flow model to analyze the cavitation, velocity distribution and experimental cavitation intensity of fishing net cleaning equipment. Results show that the cavitation inception, growth and collapse mainly occurred in the peripheral region of the flow field. Ring-shaped cavitation erosion zone appeared on the test sample target. A lot of small dense erosion pits were densely distributed in the ring-shaped erosion zone, erosion marks were observed in the center. The cavitation erosion intensity was greatly affected by the nozzle structure. As the diameter of nozzle increased from 0.6 mm to 1 mm, the maximum gas volume fraction increased by 8.53%. The nozzle outlet enlargement angle greatly increased the cavitation intensity. The nozzle with an outlet angle of 30° exhibited the optimal cavitation erosion performance . The cavitation volume fraction of the nozzle with short necking structure was slightly larger than that of the nozzle with long necking structure at the same level in the necking length rang of 3mm to 7mm. In terms of the influence of nozzle structure on the cavitation erosion effect, the nozzle diameter D ranked the first, followed by the outlet angle α, and the necking length L was at the last.

Carbon monoxide (CO) is a cytoprotective endogenous gas that is ubiquitously produced by the stress response enzyme heme-oxygenase. Being a gas, CO rapidly diffuses through tissues and binds to hemoglobin (Hb) increasing carboxyhemoglobin (COHb) levels. COHb can be formed in the erythrocytes or in plasma from cell-free Hb. Herein, it is discussed whether endogenous COHb is or is not an innocuous and inevitable metabolic waste product and it is hypothesized that COHb has a biological role. In the present review literature data is presented to support this hypothesis based on two main premises: (i) there is no direct correlation between COHb levels and CO toxicity; and (ii) COHb seems to have a direct cytoprotective and antioxidant role in erythrocytes and in hemorrhagic models in vivo. Moreover, CO is also antioxidant by generating COHb, which protects against the pro-oxidant damaging effects of cell free Hb. Up to now COHb has been considered as a sink for both exogenous and endogenous CO generated during CO intoxication or heme metabolism, respectively. Hallmarking COHb as an important molecule with a biological (and eventually beneficial) role is a turning point on CO Biology research, namely in CO intoxication and CO cytoprotection.

Wearable computing is a fast evolving segment of computing that includes smart watches, head mounted wearables such as Magic Leap headsets, Microsoft Hololens, and VR goggles from various vendors. In this report, we present ideas for a smart wearable device that also doubles as a virus protection device. Instead of using the filtering approach that is predominantly used by virus protection equipments such as face masks, we propose to use a computational approach where the device maintains an awareness of the real-time virus spread and use that information to steer the wearer away from the virus. As the wearable has a head enclosing design, viral infection can only happen through the air that is inhaled by the wearer. The objective of the smart wearable is to maintain a repository for clean air and switch the operating modes between stored and fresh air modes depending on the environmental conditions. It can augment this basic operating procedure by recycling the exhaled air to maximize it operating capacity (i.e., time duration for which it could supply the wearer with safe air) and by cleaning the stored air using UVC to further reduces the chance of infection. To maintain an awareness of the virus spread in the environment, the smart wearable will rely on an edge computing framework that will be distributed to cover areas frequented by people. The smart wearable will have modular design so that it can be reconfigured to add or subtract functionality that the wearer wants for a particular situation so that the design remains relevant even after the virus threat recedes.

The subject of study in the article is the method of industrial equipment vibration diagnostics using Allan variance. The goal is to increase the precision and accuracy of industrial equipment's vibration diagnostics processes by developing and implementing IoT-oriented solutions based on intelligent sensors and actuators per the IEEE 1451.0-2007 standard. Tasks: justify the feasibility of using platform-oriented technologies for vibration diagnostics of industrial equipment and choose a cloud service for the implementation of the platform; develop software and hardware solutions of the IoT platform for vibration diagnostics of industrial equipment; calibrate the vibration diagnostics system and check the measurement precision and accuracy. The methods used are the microservice approach, multilevel architecture, and assessing equipment state-based Allan variance. We obtained the following results. The architecture of the IoT system for vibration diagnostics of industrial equipment developed and presented in the article is three-level. The level of autonomous sensors provides readings of vibration acceleration indicators and transmits data to the Hub level, which is implemented based on a BeagleBone single-board microcomputer through the BLE digital wireless data transmission channel. BeagleBone computing power provides work with artificial intelligence algorithms. At the third level of the server platform, the tasks of diagnosing and predicting the condition of the equipment are solved, for which the Dictionary Learning algorithm implemented in the Python programming language is applied. Verifying the accelerometer calibration method for vibration diagnostics of industrial equipment was performed using a unique stand. Correct operation of the entire system is confirmed by the coincidence of expected and measured results. In the next step, we plan the development of additional microservices that will provide the possibility of using time series analysis methods and modern artificial intelligence technologies for complex diagnostics and forecasting of the equipment state.

The operation status of manufacturing equipment is directly related to the reliability of the operation of manufacturing equipment and the continuity of operation of the production system. Based on the analysis of the operation status of manufacturing equipment and its characteristics, it is proposed that the concept of assessing the operation status of manufacturing equipment can be realized by applying real-time acquisition of accurate inspection data of important parts of weak motion units and comparing them with their motion status evaluation criteria. Through the study of the application characteristics of fractional-order calculus theory, a differential data fusion model based on the fractional-order differential operator is established. The advantages of Internet of Things (IoT）technology and fractional order differential fusion algorithm are integrated to obtain real-time high-precision data of the operating parameters of manufacturing equipment, and the research objective of operating condition assessment of manufacturing equipment is realized. The feasibility and effectiveness of the method are verified by the application of the method in machining center operation status assessment.

Base on building information modeling(BIM) plus with Robotic process automation (RPA) technology is rapid development in smart building operations and maintenance (O&M). RPA is a workflow-based automated execution tool that is particularly well suited for replacing manual execution of simple and repetitive tasks using computer systems. The use of RPA technology can saves man-hours and increases productivity, which is important for the automation of building operations and maintenance operations.. The BIM technology, as an advanced technology in the construction industry, it can provide new ideas and methods for building operation and maintenance based on its visualization characteristics. That’s integrating RPA with BIM technology which will enhance the digitalization and virtualization of smart building operation and management. In this article will first introduce the features of RPA and BIM technology and then discuss the technical roadmap for remote automated operation and maintenance of smart building equipment room to implemention a low-cost and high efficient building equipment room operation and maintenance solution.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

Facial expression recognition is crucial for understanding human emotions and nonverbal communication. With the growing prevalence of facial recognition technology and its various applications, accurate and efficient facial expression recognition has become a significant research area. However, most previous methods have focused on designing unique deep-learning architectures while overlooking the loss function. This study presents a new loss function that allows simultaneous consideration of inter- and intra-class variations to be applied to CNN architecture for facial expression recognition. More concretely, this loss function reduces the intra-class variations by minimizing the distances between the deep features and their corresponding class centers. It also increases the inter-class variations by maximizing the distances between deep features and their non-corresponding class centers, and the distances between different class centers. Numerical results from several benchmark facial expression databases, such as Cohn-Kanade Plus, Oulu-Casia, MMI, and FER2013, are provided to prove the capability of the proposed loss function compared with existing ones.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

The integration of Artificial Intelligence (AI) in dairy farm management through biometric facial recognition for cows is a significant stride in livestock management. This review critically evaluates the evolution, applications, and challenges of AI-driven biometric facial recognition in dairy farming. It emphasizes the role of this technology in enhancing individual monitoring of dairy cows, providing accurate health, behavior, and productivity tracking. Originally derived from human facial recognition systems, this approach utilizes distinctive bovine facial features for essential, non-invasive, real-time monitoring in large-scale operations. The progression of AI from elementary pattern recognition to advanced Convolutional Neural Networks (CNNs) and deep learning models marks a shift toward data-driven farming. This study addresses key challenges such as environmental variability, data collection hurdles, ethical concerns, and technological limitations. It also contrasts various AI models, spotlighting their unique strengths and practical utility in dairy farming scenarios. Despite these challenges, facial recognition technology holds promise for improving farm efficiency, animal welfare, and sustainable practices, highlighting the need for continuous research and development. The review concludes by advocating for future research focused on environmental adaptability, ethical AI application, cross-breed compatibility, and integration with other farming technologies. Ultimately, it underscores AI's transformative potential in modernizing dairy farming towards a more data-oriented, responsible agricultural future.

The study of paraneoplastic syndromes in humans has a long history, whereas for domestic animals – only since the beginning of the 21^th century. There are various forms of paraneoplastic syndromes; many classifications based on pathogenetic, organ-system principles are described. In accordance with the modern classification, paraneoplastic syndromes are divided into endocrinopathies, hematological paraneoplastic syndromes, gastrointestinal, renal, dermatological, neurological, ophthalmological. The purpose of this study was to develop a scientifically based algorithm for diagnosing ophthalmopathies against the background of paraneoplastic syndrome in dogs, including a multifactorial system of “hormonal-drug treatment” of paraneoplastic ophthalmopathies. The work used a comprehensive methodological approach, including the collection of anamnestic data, clinical examination of the animal, examination of the area of the pathological process, hematological studies, cytomorphological studies, visual diagnostic methods with complete oncological and ophthalmological examinations using the necessary equipment. Treatment for cancer included surgical removal of the tumor, chemotherapy and radiotherapy. The choice of treatment protocol depended on the location of the disease, tumor phenotype (if present) and stage of the malignancy. The only chemotherapy was applied using complex protocols in the treatment of dog lymphomas. Treatment of melanoma in dogs was carried out using an integrated approach which combined methods of surgery, chemotherapy, and radiotherapy. The obtained results can be recommended for use in the diagnosis and treatment of paraneoplastic ophthalmopathies in dogs.

The current paradigm shift in orthodontic treatment planning is based on facially driven diagnostics. This requires an affordable, convenient, and non-invasive solution for face scanning. Therefore, utilization of smartphones` TrueDepth sensors is very tempting. TrueDepth refers to front-facing cameras with a dot projector in Apple devices that provide real-time depth data in addition to visual information. There are several applications that tout themselves as accurate solutions for 3D scanning of the face in dentistry. Their clinical accuracy has been uncertain. This study focuses on evaluating the accuracy of the Bellus3D Dental Pro app, which uses Apple's TrueDepth sensor. The app reconstructs a virtual, high-resolution version of the face, which is available for download as a 3D object. In this paper, sixty TrueDepth scans of the face were compared to sixty corresponding facial surfaces segmented from CBCT. Difference maps were created for each pair and evaluated in specific facial regions. The results confirmed statistically significant differences in some facial regions in amplitudes greater than 3 mm, suggesting that current technology has limited applicability for clinical use. The clinical utilization of facial scanning for orthodontic evaluation, which does not require accuracy in the lip region below 3 mm, can be considered.

In recent years, semiconductor survey meters have been developed and are in increasing demand worldwide. This study aimed to investigate whether it is possible to calculate the time constant of the semiconductor survey meter using the X-ray equipment installed in each medical facility and whether it is possible to calibrate the semiconductor survey meter. Attach an additional filter to the medical X-ray system to satisfy the standards of N-60 to N-120, add more copper plates from there, and calculate the first and second half-value layers to compare with N-60 to N-120 values. Next, we will measure the leakage dose using a medical X-ray system and calculate the time constant of the survey meter. The survey meter is then calibrated and compared with the calibration factors in industrial X-ray system. Per experimental results, it is possible to reproduce the N-60 to N-120 radiation quality using a medical X-ray system and to calculate the time constant from the measured results assuming actual leakage dosimetry using that radiation quality. We also found that the calibration factor was equivalent to that of an industrial X-ray device. It was revealed that semiconductor survey meters can be calibrated using a medical X-ray system.

In large industrial plants, the trend is to move the position of the human to the area of service and diagnostics, in medium and smaller plants the trend is different and is mainly directed to the sphere of close cooperation between the human and the robotic system. This paper deals with the implementation of human-cooperating robots in manufacturing processes. The analytical part of the paper deals with theoretical knowledge, taking into account the latest trends in the subject area. To achieve a successful implementation of cobots based on the above-mentioned operating systems in manufacturing systems, it is necessary to pay attention specifically to the interfacing of the robotic operating system with the control systems of the manufacturing systems at the process level of the enterprise. Within the practical part, an algorithm with well-defined steps towards the successful implementation of cobots in holonic manufacturing processes is proposed. By setting up an experimental workstation in the laboratory, the proposed procedures are verified at the end of the paper. In the context of the implementation of collaborative robots in enterprises, the paper also discusses cloud computing. The creation of a design for the implementation of a collaborative robot with a human represents the missing link in the whole chain of commercial applications of the latest trends from the field of robotic systems in the industrial sphere.

Due to production space and operating environment requirements, mine production equipment often breaks down, which seriously affects the mine’s production schedule. To ensure the smooth completion of the haulage operation plan under abnormal conditions, a model of the haulage equipment rescheduling plan based on the random simulation of equipment breakdowns is established in this paper. The model aims to accomplish both the maximum completion rate of the original mining plan and the minimum fluctuation of the ore grade during the rescheduling period. This model is optimized by improving the wolf colony algorithm and changing the location update formula of the individuals in the wolf colony. Then, the optimal model solution can be used to optimize the rescheduling of the haulage plan by considering equipment breakdowns. The application of the proposed method in an underground mine revealed that the completion rate of the mine’s daily mining plan reached 83.40% without increasing the number of the equipment, while and the ore quality was stable. Moreover, the improved optimization algorithm converged fast and was characterized by high robustness.

Approximately 30% of steroid-resistant nephrotic syndromes are attributed to monogenic disorders that involve 27 genes. Mutations in KANK family members have also been linked to nephrotic syndrome; however, the precise mechanism remains elusive. To investigate this, podocyte-specific Kank1 knockout mice were generated to examine phenotypic changes. In the initial assessment under normal conditions, Kank1 knockout mice showed no significant differences in the urinary albumin-creatinine ratio, blood urea nitrogen, serum creatinine levels, or histological features compared to controls. However, following kidney injury with adriamycin, podocyte-specific Kank1 knockout mice exhibited a significantly higher albumin-creatinine ratio and a significantly greater sclerotic index than control mice. Electron microscopy revealed more extensive foot process effacement in the knockout mice than in control mice. In addition, KANK1-deficient human podocytes showed increased detachment and apoptosis following adriamycin exposure. These findings suggest that KANK1 may play a protective role in mitigating podocyte damage under pathological conditions.

Treatment techniques for facial paralysis have evolved significantly over the past few decades, offering a variety of options to improve facial symmetry and muscle function. The purpose of this paper is to introduce a novel static treatment technique for the surface of the nasolabial fold (NLF) in patients with chronic facial nerve paralysis, aged between 40 and 80 years, who are not candidates for dynamic rehabilitation and present with NLF erasure. The surgical marking process was initiated by determining the projection of the nasolabial fold on the paralyzed side, through measurement of the NLF on the non-paralyzed side. Subsequently, a line was drawn around the nasal ala, and a second line was demarcated in the medial region of the sulcus. In the region close to the nasal ala, along this second line, a notch was planned. The procedure was conducted under local anesthesia. In this study, four procedures were performed without any complications. Comparatively, the outcomes demonstrated an improvement in facial symmetry, the creation of a new NLF, elevation of the ipsilateral lip commissure, and correction of nasal deviation. The proposed technique is straightforward, reproducible, and can be performed in an outpatient setting.

Emotion recognition defined as identifying human emotion and is directly related to different fields such as human-computer interfaces, human emotional processing, irrational analysis, medical diagnostics, data-driven animation, human-robot communi- cation and many more. The purpose of this study is to propose a new facial emotional recognition model using convolutional neural network. Our proposed model, “ConvNet”, detects seven specific emotions from image data including anger, disgust, fear, happiness, neutrality, sadness, and surprise. This research focuses on the model’s training accuracy in a short number of epoch which the authors can develop a real-time schema that can easily fit the model and sense emotions. Furthermore, this work focuses on the mental or emotional stuff of a man or woman using the behavioral aspects. To complete the training of the CNN network model, we use the FER2013 databases, and we test the system’s success by identifying facial expressions in the real-time. ConvNet consists of four layers of convolution together with two fully connected layers. The experimental results show that the ConvNet is able to achieve 96% training accuracy which is much better than current existing models. ConvNet also achieved validation accuracy of 65% to 70% (considering different datasets used for experiments), resulting in a higher classification accuracy compared to other existing models. We also made all the materials publicly accessible for the research community at: https://github.com/Tanoy004/Emotion-recognition-through-CNN.

Fastener holes are among the most common natural stress concentrators in metal structures. The life cycles of various structural elements, such as those in aircraft structures, automobiles, and rail-end bolt joints are limited by fatigue damage around the holes. An effective approach to delay the formation and growth of fatigue macrocracks is to introduce residual hoop compressive stresses around the holes. Two methods have become established in the prestressing of fastener holes in aircraft components: split sleeve and split mandrel, which implement one-sided processes. The common disadvantage of both methods is the complex procedure due to the need for high accuracy of the initial holes. This article presents a new modified split mandrel method providing the same tightness (interference fit) with a wide tolerance of the pre-drilled hole diameters reducing the number of technological cycle steps and production costs. То implement the new method, a functionally connected tool and a device with a hydraulic drive were developed. An extensive experimental study of 2024-T3 AA specimens was carried out to evaluate the effectiveness of the method under a high scattering of the pre-drilled holes. The new method provided a deep zone of residual hoop compressive stresses on both faces of the specimens after cold working and after hole final reaming. The removal of a plastically deformed layer around the hole of suitable thickness during the final reaming decreased the axial gradient of residual hoop stress distribution. Fatigue tests on a tensile pulsating cycle verified the effectiveness of the modified split mandrel method to significantly increase the fatigue life by 6.6 times based on cycle fatigue strength compared to the conventional case of machining the holes. The obtained S-N curves for three groups of samples with initial hole diameters of 8.0, 8.1, and 8.2 mm which were cold worked with the same tightness of 0.32 mm and final reamed, aligned well indicating that the new method can provide constant fatigue strength for a given stress amplitude.

Background: Progression of metabolic dysfunction associated steatotic liver disease (MASLD) to steatohepatitis (MASH) is driven by stress-inducing lipids that promote liver inflammation and fibrosis. MASH can lead to cirrhosis and hepatocellular carcinoma. We showed coordinated defenses regulated by transcription factors, nuclear factor erythroid 2 related factor-1 (Nrf1) and -2 (Nrf2), protect against hepatic lipid stress. Here, we investigated protective effects of hepatocyte Nrf1 and Nrf2 against MASLD-induced liver fibrosis and tumorigenesis. Methods: Using mice fed MASH diet for 24-52 weeks, we examined MASLD in mice with hepatocyte specific Nrf1, Nrf2, or combined deletion, and compared this to control. In a separate study, mice received weekly injections of carbon tetrachloride to induce liver fibrosis. From week 16-24, mice were treated with Nrf2 activating drug bardoxolone, hepatocyte overexpression of human NRF1 (hNRF1), or both, and groups were compared to control. Results: Hepatocyte Nrf2 deficiency had no effect. Hepatocyte Nrf1 and combined deficiency caused MASH but only hepatocyte Nrf1 deficiency in male mice increased tumor number. Bardoxolone reduced liver steatosis, fibrosis, inflammation, and proliferation, and this effect when combined with hNRF1 was greater than bardoxolone alone. Conclusion: Physiologic Nrf1 delays MASLD progression, Nrf2-induction alleviates MASH, and combined enhancement synergistically protects against steatosis.

Magnesium alloy stents have been extensively studied in the field of biodegradable metal stents due to their exceptional biocompatibility, biodegradability and excellent biomechanical properties. Nevertheless, the specific in vivo service environment causes magnesium alloy stents to degrade rapidly and fail to provide sufficient support for certain time. This paper presents an overview of the development history and protection strategies for magnesium alloy stents. Alloying, optimizing stent structure and preparing protective coating have improved the corrosion resistance of magnesium alloy stents. Based on the corrosion mechanism of magnesium alloy stents, as well as their deformation during use and environmental characteristics, we present some novel solution strategies aiming at reducing the corrosion rate of magnesium alloys and enhancing the comprehensive performance of magnesium alloy stents. These strategies include adapting protective coatings for the deformation of the stents, preparing rapid endothelialization coatings to enhance the service environment of the stent, and constructing coatings with self-healing functions. It is hoped that this review can help to understand the development of magnesium alloy cardiovascular stents and solve the problems related to magnesium alloy stents in clinical applications at the early implantation stage.

Neutral facial expression recognition is of great importance in various domains and applications. This study introduces a data-centric approach for neutral facial expression recognition, presenting a comprehensive study that explores different methodologies, techniques, and challenges in the field to foster a deeper understanding. The results show that data augmentation plays a crucial role in improving dataset performance. Additionally, the study investigates different model architectures and training techniques to identify the most effective approach, with the InceptionV3 model achieving the highest accuracy of 72%. Furthermore, the research examines the influence of preprocessing methods on the performance of both InceptionV3 and a simplified CNN model. Interestingly, the results indicate that preprocessing techniques positively affect the performance of the simpler CNN model but negatively impact the InceptionV3 model. The implemented system, used to evaluate the findings, demonstrates promising results, correctly classifying 77% of neutral expressions. However, there are still areas for improvement. Creating a specialized dataset that includes both neutral and non-neutral expressions would greatly enhance the accuracy of the system. By addressing limitations and implementing suggested improvements, neutral facial expression recognition can be significantly enhanced, leading to more effective and accurate results.

Short chain quinones (SCQs) have been identified as potential drug candidates against mitochondrial dysfunction, which is largely dependent on their reversible redox characteristics of the active quinone core. We recently synthesized a SCQ library of > 148 naphthoquinone derivatives and identified 16 compounds with enhanced cytoprotection compared to the clinically used benzoquinone idebenone. One of the major drawbacks of idebenone is its high metabolic conversion in the liver, which significantly restricts is therapeutic activity. Therefore, this study assessed the metabolic stability of the 16 identified naphthoquinone derivatives 1-16 using hepatocarcinoma cells in combination with an optimized reverse-phase liquid chromatography (RP-LC) method. Most of the derivatives showed significantly better stability than idebenone over 6 hours (p < 0.001). By extending the side-chain of SCQs, increased stability for some compounds was observed. Metabolic conversion from the derivative 3 to 5 and reduced idebenone metabolism in the presence of 5 were also observed. These results highlight the therapeutic potential of naphthoquinone-based SCQs and provide essential insights for future drug design, prodrug therapy and polytherapy, respectively.

Human Face and facial parts are the most significant parts as it reveals a person’s true identity. It plays an important role in various biometric applications like crowd analysis, human tracking, photography, cosmetic surgery, etc. There are many techniques are available to detect a facial image. Among them, skin detection is the most popular one. The aim of this paper is to detect first the person's identity from facial image and finally check any spot present the the detected person. The first step is to detect the maximum skin region based on a combination method of RGB and HSV color space model. Next it is to verify the skin areas of human through machine learning approach. The Aggregated Channel Features (ACF) detector is used to identify the different facial parts like eye pairs, nose, and mouth. Bootstrap aggregation decision tree classifier is applied to classify the person’s identity based on Histogram Oriented Gradient (HOG) features value. The experimental results show that the proposed method gives the average 97% accuracy.

Patients with excessive gingival display (EGD) are treated with lip repositioning surgeries (LRS). This study used a questionnaire to analyze and evaluate how patients who received LRS with modified and traditional techniques perceived their own oral and facial aesthetics at various timelines after their surgeries. An orofacial esthetic questionnaire (OEQ) was used in this cross-sectional study. The participants were patients who underwent LRS for treatment of their EGD were divided into control (n=100) and test (n=100) groups. For control group, LRS were performed using traditional/conventional technique and for test group, LRS were performed by modified approach. OEQ was used to record responses. The scale comprised of eight questions targeted to capture participating patient’s perceptions about their own oral and facial aesthetics at four timelines (Baseline; 1 Month; 6 Months &amp; 1 Year). Patients responded to each question on a 10 point Likert scale (Range: 0=very dissatisfied to 10= very satisfied). Data was analyzed by independent samples T-tests, using SPSS software. 7 (3.5%) out of the total (200) patients were unable to take part in the study's OEQ. At a one-year follow-up, the mean and standard deviation for the test group's GD were 2.48+0.86mm and 3.77+1.76mm, respectively, and comparisons revealed that the test group's GD was significantly lower (p=0.000) than the control group. Results from the participant responses to OEQ using the Likert scale at the 1-year follow-up revealed significant differences between control and test groups for all questions, except Q5 (P=0.06) as shape of the teeth will not be affected by LRS. Test group patients who underwent the LRS with modified approach were having high level of satisfaction (satisfaction-score&gt;9). Patients in control group scored their satisfaction less favorably, with certain questions (Q3) receiving scores as low as 0.31. The test group's perception of oral and facial esthetics, was significantly higher for test group at different time points. At the 1-year follow-up, the mean difference was 4.46, which was the greatest (P=0.000). The EGD improved significantly at one year with the modified lip repositioning technique. The satisfaction level of the patients with outcomes of modified lip repositioning was significantly higher as compared to conventional technique.

(1) Background: The lateral arm flap has been the very useful choice in the reconstruction of small- to medium-sized defects like hand, extremity, oral head and neck area reconstructions. Its versatile characteristics and surgical feasibility allow this flap to be widely applied, but the reconstructive potential in facial subunit after tumor ablative procedures has never been reported. In this study, we aimed to utilize the advantages of the flap to treat facial temple subunit defect reconstruction. (2) Methods: Between 2020 and 2023, 12 patients underwent temple reconstruction with lateral arm free flaps after malignant tumor wide excision. There were 7 women and 5 men, and the mean patient age was 60.6 years old. Among the patients with cancer, 6 had squamous cell carcinoma, 5 had basal cell carcinoma and 1 had myxofibrosarcoma. All the flaps were elevated under general anesthesia. Aloprostadil(PGE1, Eglandin®) were administered postoperatively. (3) Results: All the flap types were fasciocutaneous type with varied sizes from 3 × 4 to 5 × 7 cm (Average size of flap 22.7cm2) were utilized. The average pedicle length was 6.1cm. The versatility of the lateral arm flap enabled successful coverage of all cases with no specific complications. Good functional outcome and range of motion in the recipient arm were obtained after surgery. (4) Conclusion: The authors successfully verified the advantages of lateral arm flaps in the treatment of medium sized facial subunt temple defect reconstruction.