Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

Genetic Programming (GP) is a powerful Machine Learning (ML) algorithm that can produce readable white-box models. Although successfully used for solving an array of problems in different scientific areas, GP is still not well known in Remote Sensing. The M3GP algorithm, a variant of the standard GP algorithm, performs Feature Construction by evolving hyper-features from the original ones. In this work, we use the M3GP algorithm on several sets of satellite images over different countries to create hyper-feature from satellite bands to improve the classification of land cover types. We add the evolved hyper-features to the reference datasets and observe a significant improvement of the performance of three state-of-the-art ML algorithms (Decision Trees, Random Forests and XGBoost) on multiclass classifications and no significant effect on the binary classifications. We show that adding the M3GP hyper-features to the reference datasets brings better results than adding the well-known spectral indices NDVI, NDWI and NBR. We also compare the performance of the M3GP hyper-features in the binary classification problems with those created by other Feature Construction methods like FFX and EFS.

The collapsible loess will rapidly soften and lose its bearing capacity when soaked in water. Under a mild condition (20°C), the biomimetic inorganic agent, Diammonium phosphate (DAP), reacts with calcite in the collapsible loess, producing a stronger bonding material, hydroxyapatite (HAP), to modify and stabilize the soil. Uniaxial compression, permeability tests and morphological analysis using XRD and SEM/EDX microscopy were carried out to assess the effectiveness of DAP stabilization on the collapsible loess. The results indicated that HAP improved the inter-particle bonding within loess, filled the pores within particles, reduced the permeability, and consequently mitigated collapsibility of loess. The compressive strength of DAP-treated loess increased as DAP concentration increased. Following 28-days curing, the compressive strength of the loess treated with a 3.0 mol/L DAP solution was six times greater than that of the untreated group. DAP's reinforcement effect on loess was superior to that of cement. The compressive strength of DAP-treated loess was about double that of cement-treated loess and the permeability coefficient was reduced by more than 50% at equivalent solid content. Furthermore, DAP generated 68% fewer carbon emissions compared to Portland cement. Considering eco-friendly and sustainable development, DAP offers a more competitive alternative for modification and stabilization of loess.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P < 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Structures inevitably suffer damages after an earthquake, with their severity ranging from minimal damages to non-structural elements to partial or even total collapse, possibly with loss of human lives. Thus, it is essential for engineers to understand the crucial factors that drive a structure towards suffering higher degrees of damage, so that preventative measures can be taken. In the present study, we focus on three well-known damage thresholds, namely Collapse Limit State, Ultimate Limit State and Serviceability Limit State and analyze which of the features obtained via Rapid Visual Screening, determine whether or not a given structure will cross that threshold. To this end, we use Machine Learning to perform binary classification for each damage threshold, as well as Explainability via SHAP values (acronym for SHapley Additive exPlanations) to quantify the effect of each parameter. The quantitative results obtained demonstrate the potential applicability of ML methods to re-calibrate the computation of structural vulnerability indices using data from recent earthquakes.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

The last-mile logistics in cities have become an indispensable part of the urban logistics system. This study aims to explore the effective selection of last-mile logistics nodes to enhance the efficiency of logistics distribution, strengthen the corporate distribution image, and further reduce corporate operating costs and alleviate urban traffic congestion. This paper proposes a clustering-based approach to identify urban logistics nodes from the perspective of geographic information fusion. This method comprehensively considers several key indicators, including the coverage, balance, and urban traffic conditions of logistics distribution. Additionally, we employed a greedy algorithm to identify secondary nodes around primary nodes, thus constructing an effective nodal network. To verify the practicality of this model, we conducted an empirical simulation study using the logistics demand and traffic conditions in the Xianlin District of Nanjing. This research not only identified the locations of primary and secondary logistics nodes but also provided a new perspective for constructing the urban last-mile logistics system, enriching the academic research related to logistics node construction. The results of this study are of significant theoretical and practical importance for optimizing urban logistics networks, enhancing logistics efficiency, and promoting the improvement of urban traffic conditions.

Ransomware attacks have risen alarmingly, with encryption techniques becoming more complex. This paper introduces a novel detection model tailored for ransomware's distinctive characteristics. The Intel PIN tool extracts Windows API invocation sequences related to file operations. These sequences are used to construct n-grams, forming feature vectors enhanced by a new Class Feature Weighting (CFW) metric to improve malware detection. Preliminary results demonstrate elevated accuracy and precision versus existing methods. The major contributions are: (1) Introducing an innovative deep learning model for few-shot ransomware classification using entropy features and transfer learning. (2) Achieving high weighted F1-score in classifying ransomware variants into families with limited training data. (3) Demonstrating the potential of entropy-based features to capture intricacies lost in image-based approaches, improving detection of new strains.

Radio Occultation (RO) is pivotal for profiling the neutral and ionized atmosphere, with the PlanetiQ mission, via its GNOMES satellites, striving to establish an advanced atmospheric observing system. However, an assessment of the spatiotemporal distributions of PlanetiQ observations and comparisons with reliable datasets are lacking. This study addresses this gap by examining the temporal and spatial distribution of RO observations from PlanetiQ during its initial 198 operational days in 2023, alongside comparisons with COSMIC and Numerical Weather Prediction (NWP) models. Data from GN02, GN03, and GN04 satellites, yielding 1099, 1313, and 1843 RO events per day respectively, were analyzed. The satellite constellation's observations demonstrate a generally well-distributed pattern, albeit minor deficiencies in equatorial and polar regions. Single-profile comparisons with COSMIC data reveal strong correlations for pressure, temperature, Water Vapor Pressure (WVP), and refractivity profiles, with temperature exhibiting larger variations (RMSE = 1.24°C). Statistical analyses confirm statistically insignificant differences between PlanetiQ and COSMIC profiles at the same spatio-temporal coordinates. Comparisons with NWP models show slight differences with GFS, with overall RMSE values of 0.23 mb (WVP), 0.6 mb (pressure), 1.3 (refractivity), and 1.5°C (temperature). However, assessments against GFS/ECMWF models indicate overall compatibility, with insignificant differences between PlanetiQ profiles and models observations.

In a hyperconnected society, computer networks play a pivotal role in all activities that permeate our daily lives. In the context of smart cities, theses networks play a pivotal role in enhancing urban efficiency and sustainability. The continuous flow of packets in these networks poses security challenges, from personal data leakage to service unavailability. Anomaly-based methods are commonly used to detect network attacks. In this context, Software-Defined Networking (SDN) emerges as a solution for anomaly detection in network traffic, facilitating comprehensive, real-time analyses and dynamic adaptation to changes. This study aims to present a systematic review of feature selection techniques and evaluate the effectiveness of attribute selection with a multi-class classifier in network anomaly detection. The objective of this paper is to inspire future research and identify trade-offs among these techniques for detecting Denial of Service (DoS) attacks. Based on the findings, the analysis of the entire dataset yields superior results in terms of precision (99%), but using the output of OneR, although resulting in a slight loss of precision compared to the complete dataset, presents the highest precision among other studied techniques, indicating a trade-off between precision and processing time efficiency.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.

Sustainability is a characteristic manifested in the ability to maintain the necessary level of performance for construction companies when risk factors arise during the implementation of investment and construction projects. The risk factors that arise during the implementation of in-vestment and construction projects differ in nature, degree of influence, and other characteristics. Ignoring these factors and measures to manage them often leads to critical consequences in the form of disruptions in the timing of work. Risk is a combination of the probability and consequences of the occurrence of adverse events. The article considers the concept of risk as a potential possibility of occurrence of adverse situations and related consequences when exposed to these factors. Risk factors are characterized by surprise, discreteness of changes, the presence of threshold values, upon reaching which a transition to a different mode of operation is required. The article discusses the risk factors arising at the construction stage, their classification. A methodology has been developed that includes conducting a survey in the form of a questionnaire in order to collect information about risk factors that affect the implementation of investment and construction projects. Experts with experience in the construction sector were involved in the survey. The processing of the survey results made it possible to assess the significance of various risk factors in investment and construction projects. Thus, statistical and expert methods were used in the study. The results showed that financial, technical, legal, economic, managerial and natural factors have the greatest impact on investment and construction projects. It is recommended to pay special attention to the listed factors when developing measures aimed at preventing risks and their consequences. The methodology described in the study can be used by construction companies in strategic planning. The analysis of the stability of construction companies, depending on their use of various ways to counteract risk factors, allowed us to develop a number of practical recommendations to reduce the impact of the studied factors on achieving the goals of investment and construction projects.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

The development of one technology can be portrayed by common methods like Gartner’s hype cycle or S-curve, however, there is no method to characterize the feature distributions of multiple technologies within a specific domain. This study proposes a big data-based method in terms of four proposed features, namely versatility, significance, commerciality, and disruptiveness, to characterize the technologies within a given domain. The features of technologies are quantitively portrayed using the representative keywords and volumes of returned search results from Google and Google Scholar in two-dimensional analytical spaces of technique and application. We demonstrate the applicability of this method using 452 technologies in the domain of intelligent robotics. The results of our assessment indicate that the versatility values are normally distributed, while the values of significance, commerciality, and disruptiveness follow power-law distributions, in which few technologies possess higher feature values. We also show that significant technologies are more likely to be commercialized or causing potential disruption, as such technologies have higher scores in these features. Further, we validly prove the robustness of our approach via comparing historical trends with literature and characterizing technologies in reduced analytical spaces. Our method can be widely applied in analyzing feature distributions of technologies in different domains, and it can potentially be exploited in decisions like investment, trade, and science policy.

With the growing trend of urbanization and the growing number of people migrating to cities, the demand for the development and construction of new buildings as well as the infrastructure has risen, meaning that the construction industry must adapt to the trends. The growing demands with shorter deadlines for an industry already known for high costs and not delivering on time means that productivity must be increased without increasing the cost. The solution for this might lie in the application of the Lean philosophy to the construction industry. This paper analyses the application of the Lean philosophy in order to increase the productivity in the airport construction site. The paper highlights the potential for enhancing productivity in construction workplaces by concurrently fostering continuous improvement and sustainability through the implementation of the A3 methodology and Lean principles, resulting in waste reduction and increased value.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

The problem of normal impact of a rigid sphere onto a Maxwell viscoelastic solid half-space is considered. The first-order asymptotic solution is constructed in the framework of Hunter’s model of viscoelastic impact [Hunter, S. C., 1957. Energy absorbed by elastic waves during impact. Journal of the Mechanics and Physics of Solids, 5(3), 162–171.]. In particular, simple analytical approximations have been derived for the maximum contact force and the time to achieve it. A linear regression method is suggested for evaluating the instantaneous elastic modulus and the mean relaxation time from a set of experimental data collected for different impactors and impact velocities.

The global coronavirus (COVID-19) pandemic has created a whole new set of risks in construction industries generating unprecedented delays, disruptions, and uncertainty on construction projects, and has forced the industries in adopting more sophisticated technologies while combating the reduced workforce on job sites. Further, the post-pandemic era of construction is expected to be a lot different as the industries will embrace the technology as the augmentation and collaboration strategy. Thus, it will be extremely hard to sustain for construction industries in the absence of effective risk management. The existing risk plans need to be inspected for their capability of handling new risks arising from COVID-19 and the project managers will need to make the necessary revisions as needed. This paper discusses on past (NORM), present (NEW NORM), and future (Post COVID-19 NORM) of the construction industry and highlights key strategies for managing projects and construction risks during and post COVID-19 pandemic.

With the increase in technological advancements, architects and engineers over the past couple of decades have been trying to achieve high efficiency within construction projects. Their goals also include reducing global warming effects from construction and building new construction faster for the growing population in urban cities. This requires using a construction method that is less harmful to the environment and faster than other traditional methods. Modular construction, also known as modular construction, is the method that has the potential to make this happen. This review paper discusses what modular construction is and how it is different from the traditional on-site construction. Environmental impacts of using modular construction and what leads to it being more efficient and faster than on-site construction. The study doesn’t suggest that modular construction is the solution to all the problems being faced in the construction industry today, but it is a potential solution that if used in the right situation and correct manner, can have a huge positive impact on the construction industry.

Efficient fixed crane position analysis is critical in precast buildings construction to maximize lifting efficiency for precast elements. The primary objective is to minimize the travel distances of fixed cranes, thereby enhancing operational efficiency and cost control. This involves strategically reducing the distances between the transport truck parking, where elements are stored, the fixed crane, and the construction installation point. Despite its significance, existing studies often overlook the dynamic movement efficiency of transport trucks, particularly when dealing with multiple transport trucks and various models of fixed cranes, rendering the opti-mization of this scenario a challenging NP-hard problem susceptible to combinatorial explosion. This study presents a novel mathematical model leveraging the Genetic Algorithm (GA). The model aims to solve optimal model and position of fixed cranes, along with identifying ideal positions for transport truck parking. The study's methodology is validated and demonstrated through a project case study. Comparative analyses between the proposed model and the original planning underscore a noteworthy 6% reduction in both duration and costs when lifting elements directly from transport trucks, as opposed to establishing an on-site stock yard. Furthermore, the developed GA exhibits a substantial improvement in final solutions, achieving a remarkable 30% reduction in both operational duration and costs. This research contributes valuable insights into fixed crane position analysis of precast building construction, providing foundation for enhanced operational efficiency and cost-effectiveness in the industry.

The construction industry is a resource and energy intensive industry and thus, has been criti-cized due to rising environmental concerns. As a result of that it has gained heightened interest in the concept of Circular Economy (CE) over the last decade to its ability to promote the slowing, reducing, and closing production and consumption cycles of materials and products used in the construction practices. Digital technologies hold potential to enhance the construction industry's ability to integrate the concept of CE in its practices. However, a clear understanding of digital technology (DT) related barriers that hinder practical implementation of CE, appears to be lacking within the sector. In light of this, this study aims to identify the barriers to adopting DTs to im-plement CE practices in the construction industry. To achieve this aim, a systematic literature review was conducted by reviewing twenty-three (23) relevant papers published until January 2024 in Scopus database. The VOS viewer software was used to perform a co-occurrence analysis of keywords to identify new and popular study areas in the field and content analysis was used to analyse the major barriers to adapt DTs to implement CE in the construction industry. The study identified thirty-four (34) barriers to use DTs to implement CE and these were categorized into nine areas such as: infrastructure, organizational, regulatory, standardization, investment, nature of the construction industry, technological, stakeholder and data related barriers. These findings will be beneficial for construction practitioners and policy makers to adopt DTs to integrate CE practices in the construction industry.

Recently, significant progress has been made in developing computer-aided diagnosis (CAD) systems for identifying glaucoma abnormalities using fundus images. Despite their drawbacks, methods for extracting features such as wavelets and their variations, along with classifier like support vector machines (SVM), are frequently employed in such systems. This paper introduces a practical and enhanced system for detecting glaucoma in fundus images. This system adresses the chanallages encountered by other existing models in recent litrature. Initially, we have employed contrast limited adaputive histogram equalization (CLAHE) to enhanced the visualization of input fundus inmages. Then, the discrete ripplet-II transform (DR2T) employing a degree of 2 for feature extraction. Subsequently, a golden jackal optimization algorithm (GJO) employed to select the optimal features to reduce the dimension of the extracted feature vector. During the classification stage the least square support vector machine (LS-SVM) with three kernels called as linear, polynomial and radial basis function(RBF), for classifying of fundus images as glaucoma or healthy. The proposed method is validated with the current state-of-the-art models on two standard datasets, namely, G1020 and ORIGA. The results obtained from our experimental result demonstrate that our best suggested approach DR2T+GJO+LS-SVM-RBF obtains better classification accuracy 93.38% and 97.31% for G1020 and ORIGA dataset with less number of features. It establishes a more concise network structure when contrasted with traditional classifiers.

Crowd density estimation is an important task for crowd monitoring. Many efforts have been done to automate the process of estimating crowd density from images and videos. Despite series of efforts, it remains a challenging task. In this paper, we proposes a new texture feature-based approach for the estimation of crowd density based on Completed Local Binary Pattern (CLBP). We first divide the image into blocks and then re-divide the blocks into cells. For each cell, we compute CLBP and then concatenate them to describe the texture of the corresponding block. We then train a multi-class Support Vector Machine (SVM) classifier, which classifies each block of image into one of four categories, i.e. Very Low, Low, Medium, and High. We evaluate our technique on the PETS 2009 dataset, and from the experiments, we show to achieve 95% accuracy for the proposed descriptor. We also compare other state-of-the-art texture descriptors and from the experimental results, we show that our proposed method outperforms other state-of-the-art methods.

In this paper, the authors seek to discuss some of the complexities involved in cross-cultural working in relation to the communication and management of pain in older people. Specifically, the paper addresses the culture construction of ageing and how pain is often constructed as a natural part of ageing. The authors also suggests that with the rise of the ideology of active-ageing many older people who are disabled or living in chronic pain, may feel a moral imperative to hide pain and ill-health. The discussion extends into looking at the impact of culture and the communication of pain, including specific idioms of distress, somaticize and the lay-management of pain through stoicism.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system proposed is interpreted as an additional tool which can be utilized in several applications, where the system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A Programmable Logic Controller enables the Node-Red to be utilized. This open-source programming tool employs flows to define operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper, each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT Station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms.

With the growing of university chemistry experiment projects, scientific research personnel, specialized equipment, laboratory accident is increasing yearly. And accident data lacks a safety platform to store related information and cannot be guaranteed for efficient conditional sharing. To solve these problems, we designed a laboratory accident system to store, share related data and predict risk level. In this paper, we manually collected chemistry laboratory accidents by python software and class assignments, then analyses risk factor variables using Spsspro, finally established a prediction model using Stata. We intended to register laboratory related data into proposed chemistry accident system based on data ownership safety architecture. The chemistry accident system can break data barriers using confirmation and authorization key technology to trace non-tampered data source in real time when emergency accident happens. Meanwhile, our proposed system can use our designed accident risk model to predict risk level of any experiment project. It can also recommend appropriate safety education models.

The paradigm of leveraging code as a dataset has recently gained traction, offering innovative solutions in domains such as automated commit message generation, pull request description automation, and program repair mechanisms. Consider the challenge in generating commit messages: traditional methods treat source code as a mere token sequence, applying neural machine translation models. This approach, however, overlooks the critical syntactic structures inherent in programming languages, which could offer deeper insights and improved accuracy. Building upon prior research, specifically the Code2Seq framework, which utilized Abstract Syntax Tree (AST) structural data for source code representation to automate method name generation, this paper extends and refines this concept. We introduce "CSR", a novel methodology adapted to represent code edits effectively. This paper investigates the impact of employing syntactic structure, focusing on the classification of code edits. Drawing inspiration from Code2Seq, "CSR" utilizes AST's structural properties, particularly the paths connecting leaf nodes, to enhance the task of code edit classification. This approach is rigorously evaluated on two distinct datasets, comprising fine-grained syntactic edits. Our comprehensive experiments reveal that incorporating syntactic structures does not significantly outperform simpler methodologies. While methods like Code2Seq and our proposed "CSR" show potential, our findings highlight that there is considerable scope for improvement and refinement before such techniques can be universally applied for learning representations of code edits. We anticipate that our findings will spark further research in this field, paving the way for more effective use of syntactic structures in code representation.

Face swapping is an intriguing and intricate task in the field of computer vision. Currently, most mainstream face swapping methods employ face recognition models to extract identity features and inject them into the generation process. Nonetheless, such methods often struggle to effectively transfer identity information, result in generated results failing to achieve a high identity similarity with the source face. Furthermore, if we can accurately disentangle identity information, we can achieve controllable face swapping, thereby providing more choices to users. In pursuit of this goal, we propose a new face swapping framework (ControlFace) based on the disentanglement of identity information. We disentangle the structure and texture of the source face, encoding and characterizing them in the form of feature embeddings separately. According to the semantic level of each feature representation, we inject them into the corresponding feature mapper and fuse them adequately in the latent space of StyleGAN. Owing to such disentanglement of structure and texture, we are able to controllablely transfer parts of the identity features. Extensive experiments and comparisons with state-of-the-art face swapping methods demonstrate the superiority of our face swapping framework in terms of transferring identity information, producing high-quality face images and controllable face swapping.

Motivation: The visualization of biological data is a fundamental technique that enables researchers to understand and explain biology. Some of these visualizations have become iconic, for instance: tree views for taxonomy, cartoon rendering of 3D protein structures, or tracks to represent features in a gene or protein, for instance in a genome browser. Nightingale provides visualizations in the context of proteins and protein features. Results: Nightingale is a library of re-usable data visualization web components that are currently used by UniProt and InterPro, among other projects. The components can be used to display protein sequence features, variants, interaction data, 3D structure, etc. These components are flexible, allowing users to easily view multiple data sources within the same context, as well as compose these components to create a customized view. Availability: Nightingale examples and documentation are freely available at https://ebi-webcomponents.github.io/nightingale/. It is distributed under the MIT license, and its source code can be found at https://github.com/ebi-webcomponents/nightingale.

Aiming at the problems that are poor generalization performance, low retrieval accuracy and large time consumption of existing content-based image retrieval system, the hierarchical image retrieval method based on multi feature fusion is proposed in this paper. The retrieval accuracy rates on Corel5K, UKbeach and Holidays are 68.23(Top 1), 3.73(N-S) and 88.20(mAp), respectively. The experimental results show that the method proposed in this paper can effectively improve the deficiency of single feature retrieval and save time significantly in the premise of a small amount of loss of accuracy.

Biologists seek to identify a small number of significant features that are important, non-redundant, and relevant from diverse omics data. For example, statistical methods like LIMMA and DEseq distinguish differentially expressed genes between a case and control group from the transcript profile. Researchers also apply various column subset selection algorithms on genomics datasets for a similar purpose. Unfortunately, genes selected by such statistical or machine learning methods are often highly co-regulated, making their performance inconsistent. Here, we introduce a novel feature selection algorithm that selects highly disease-related and non-redundant features from a diverse set of omics datasets. We successfully applied this algorithm to three different biological problems: a) disease to normal sample classification, b) multiclass classification of different disease samples, and c) disease subtypes detection. Considering classification ROC-AUC, False-positive, and False-negative rates, our algorithm outperformed other gene selection and differential expression (DE) methods for all six types of cancer datasets from TCGA considered here for binary and multiclass classification problems. Moreover, genes picked by our algorithm improved the disease subtyping accuracy for four different cancer types over the state-of-the-art methods. Hence, we posit that our proposed feature reduction method can support the community to solve various problems, including the selection of disease-specific biomarkers, precision medicine design, and disease sub-type detection.

This work focuses on identifying the most effective machine learning techniques and supervised learning models to precisely estimate power output from Photovoltaic (PV) plants. The performance of various regression models is analyzed by harnessing experimental data, including Random Forest, Support Vector Regression (SVR), Multi-layer Perceptron (MLP), Linear Regressor (LR), Gradient Boosting, and k-Nearest Neighbors (KNN). The methodology applied starts with meticulous data preprocessing steps aimed at ensuring dataset integrity. Following the preprocessing phase, which entails eliminating missing values and outliers using Isolation Feature selection based on a correlation threshold, is performed to identify relevant parameters for accurate prediction in PV systems. Subsequently, Isolation Forest is employed for outlier detection, followed by model training and evaluation using key performance metrics such as Root Mean Squared Error (RMSE), Normalized Root Mean Squared Error (NRMSE), Mean Absolute Error (MAE), and R-squared (R2). Among the array of models evaluated, Random Forest emerges as the top performer, highlighting promising results with an RMSE of 19.413, NRMSE of 0.048% and an R2 score of 0.968. Furthermore, the best-performing model is integrated into a MATLAB application for real-time predictions, thereby enhancing usability and accessibility for a wide range of applications in renewable energy.

Like traditional single label learning, multi-label learning is also faced with the problem of dimensional disaster.Feature selection is an effective technique for dimensionality reduction and learning efficiency improvement of high-dimensional data. In this paper, Logistic regression, manifold learning and sparse regularization were combined to construct a joint framework for multi-label feature selection (LMFS). Firstly, the sparsity of the eigenweight matrix is constrained by the $L_{2,1}$-norm. Secondly, the feature manifold and label manifold can constrain the feature weight matrix to make it fit the data information and label information better. An iterative updating algorithm is designed and the convergence of the algorithm is proved.Finally, the LMFS algorithm is compared with DRMFS, SCLS and other algorithms on eight classical multi-label data sets. The experimental results show the effectiveness of LMFS algorithm.

Finding an optimal combination of features and classifier is still an open problem in the development of automatic heartbeat classification systems, especially when applications that involve resource-constrained devices are considered. In this paper, a novel study of the selection of informative features and the use of a random forest classifier while following the recommendations of the Association for the Advancement of Medical Instrumentation (AAMI) and an inter-patient division of datasets is presented. Features were selected using a filter method based on the mutual information ranking criterion on the training set. Results showed that normalized R-R intervals and features relative to the width of the QRS complex are the most discriminative among those considered. The best results achieved on the MIT-BIH Arrhythmia Database were an overall accuracy of 96.14% and F1-scores of 97.97%, 73.06%, and 90.85% in the classification of normal beats, supraventricular ectopic beats, and ventricular ectopic beats respectively. In comparison with other state of the art approaches tested under similar constraints, this work represents one of the highest performances reported to date while relying on a very small feature vector.

After proving, in a purely categorial way, that the inclusion functor InAlg(Σ) from Alg(Σ), the category of many-sorted Σ-algebras, to PAlg(Σ), the category of many-sorted partial Σ-algebras, has a left adjoint FΣ, the (absolutely) free completion functor, we recall, in connection with the functor FΣ, the generalized recursion theorem of Schmidt, which we will also call the Schmidt construction. Next we define a category Cmpl(Σ), of Σ-completions, and prove that FΣ, labeled with its domain category and the unit of the adjunction of which it is a part, is a weakly initial object in it. Following this we associate to an ordered pair (α,f), where α=(K,γ,α) is a morphism of Σ-completions from F=(C,F,η) to G=(D,G,ρ) and f a homomorphism in D from the partial Σ-algebra A to the partial Σ-algebra B, a homomorphism ΥαG,0(f):Schα(f)B. We then prove that there exists an endofunctor, ΥαG,0, of Mortw(D), the twisted morphism category of D, thus showing the naturalness of the previous construction. Afterwards we prove that, for every Σ-completion G=(D,G,ρ), there exists a functor ΥG from the comma category (Cmpl(Σ)↓G) to End(Mortw(D)), the category of endofunctors of Mortw(D), such that ΥG,0, the object mapping of ΥG, sends a morphism of Σ-completion in Cmpl(Σ) with codomain G, to the endofunctor ΥαG,0.

This study aimed to identify the influencing factors that drive the adoption of smart construction technologies by highway construction companies. Using expert interviews and expert scoring, interview data were collected from 25 experts in the field, and the TOSE framework was proposed based on the TOE framework, identifying four dimensions and fourteen influencing factors. The results were analyzed using the Fuzzy-DEMATEL-ISM method, and the findings were then summarized according to the evaluation criteria to determine the validity of the fourteen hypotheses and the extent to which they drive the adoption of intelligent construction technologies by motorway construction companies. The findings of this paper will be of great value to decision-makers and participants in highway construction companies, as well as to other companies in the construction industry, in their decision to adopt smart construction technologies.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

The focus of research has mainly been on the life cycle approach to project development, while limited attention has been given to the ageing construction companies that make all these activities/processes happen. This paper examines the organisational factors determining the sustainability and growth of building and civil engineering contractors in South Africa. The paper explores whether there are specific organisational factors that aid the sustainable development and growth of contractors in the South African construction industry. The paper analyses data gathered from face-to-face interviews conducted with four established and twelve upgraded and successful building and civil engineering contractors listed on the Construction Industry Development Board’s (cidb) Register of Contractors. The aim of the study is to identify the organisational factors critical for sustainable contractor development and growth in South Africa. The study found that organizational factors responsible for the sustainable development and growth of construction contractors include the size of the founding team members, management capabilities, strategic decisions made by founders/leaders and the ability of the company to constantly evolve, adapt and respond effectively to threats/challenges whenever they surface, amongst other findings. Capacity to generalise the results of the study to the large cidb registered contractor group is limited by the smallness of the sample size. Future research should make use of a larger sample size to obtain more general findings. The results of the study imply that the founding team size, experience, entrepreneurial and managerial capabilities, capacities and organisational structures that enable the efficient response of companies to external and internal challenges are key components of the definable arrangements that will support the sustainability and growth of construction organisations. The paper is of value to government departments and agencies such as the cidb and contracting firms in the construction industry.

Hyperspectral anomaly detection is to recognize anomalies from complex scene in an unsupervised way. Currently, many spectral-spatial detection methods have been proposed with a cascaded manner. However, they often neglect complementary characteristics between spectral and spatial dimensions, which easily leads to yield high false alarm rate. To alleviate this issue, a spectral-spatial information fusion (SSIF) method is designed for hyperspectral anomaly detection. First, an isolation forest is exploited to obtain spectral anomaly map, in which the object-level feature is constructed with entropy rate segmentation algorithm. Then, a local spatial saliency detection scheme is proposed to produce spatial anomaly result. Finally, the spectral and spatial anomaly scores are integrated together followed by a domain transform recursive filtering to generate the final detection result. Experiments on five hyperspectral datasets prove that the proposed SSIF produces superior detection result over other state-of-the-art detection techniques.

The port environments have some structures that still need regular control. However, the nature of these environments presents a number of challenges in determining an accurate vehicle position and consequently performing successful image similarity detection. These scenarios, however, can have poor visibility conditions and are highly dynamic, making place recognition difficult because the appearance of a place can change over time. Under these operational conditions, imaging sonars are a promising solution. There are some factors that affect the quality of the captured images, but the fact that they do not suffer from haze is a plus. Therefore, in this paper, a purely acoustic similarity detection method based on forward-looking sonar (FLS) data is proposed to overcome the inherent perceptual problems in a port scenario. Considering the lack of available data in this context and to facilitate the variation of environmental parameters and sensor configurations, a port scenario was simulated using the Stonefish simulator. Experiments were conducted on predefined trajectories near structures. The place recognition approach performs better compared to the results obtained with optical imagery. In general, it provides a good compromise in terms of distinctiveness and achieves a performance of 87.5% when appropriate constraints and assumptions are made.

This paper presents a new algorithm for semi-supervised action recognition using adaptive feature analysis. We model the samples of the same action as the same manifold and those of different actions as different manifolds, and integrate feature correlation mining and visual similarity mining into a joint framework. By maximizing the separability between different classes based on the labeled data, the proposed algorithm learns multiple features from labeled data and utilizes the intrinsic geometric structure of the data distribution between labeled and unlabeled data to boost the recognition. We introduce Projected Barzilai-Borwein (PBB) to train a subspace projection matrix as classifier. Extensive experiments on three benchmark datasets demonstrate that our algorithm outperforms the existing semi-supervised action recognition algorithms when there are a few labeled training samples.

Pedestrian multi-target tracking technology plays an important role in artificial intelligence, driverless, virtual reality and other fields. The pedestrian multi-target tracking algorithm DeepSORT based on detection is widely used in industry. It mainly tracks multiple pedestrian targets continuously and keeps their ID unchanged. In order to improve the applicability and tracking accuracy of DeepSORT algorithm, this paper improved the IOU distance measurement in the matching process. At the same time, ResNet50 is used as the feature extraction backbone network, and combined with FPN (Feature Pyramid Network), the appearance features of multi-layer pedestrians are fused to improve the tracking accuracy of DeepSORT algorithm. The proposed algorithm is verified on the public data set MOT-16 and it’s tracking accuracy is enhanced to 4.1%.

Failure to meet the deadlines for the implementation of investment and construction projects is a problem in all countries of the world, and leads to unstable activity of construction companies. The article studies the most important destabilizing factors affecting the main indicator of sustainable activity of construction companies-the duration of the implementation of an investment and construction projects. To determine and assess the impact of destabilizing factors on the duration of implementation of selected investment and construction projects, a survey was conducted, in which a number of customers, consultants and contractors involved in construction projects took part. Questionnaires developed on the basis of a cluster sample were sent to respondents, 48 responses were received in response to the assessment of destabilizing factors. To analyze the received and grouped information, structural equation modeling using the Smart-PLS program was used. As a result of modeling, a number of results were obtained, the most important of which are the identification of the main reasons that lead to an average (20% - 50%) increase in the duration of projects in the construction sector. The most significant were: the lack of an appropriate procurement program for materials; inefficient scheduling by contractors and instability of construction production; poor-quality processing of incoming information and untimely deci-sion-making due to changes in projects during their implementation. Destabilizing factors con-tribute to an increase in the duration of construction sector projects, which leads to time overruns, cost overruns, and an increase in the negative impact on the overall use of resources. As a result of the study, a set of recommendations was formed, the most important of which is the use of possible compensatory measures that can allow construction companies to eliminate the risks of disrupting construction deadlines for sustainable activities. These compensatory measures include: - recommendations to customers of the construction project; - recommendations to contractors; - recommendations to the consultant. Moreover, the control of destabilizing factors that can cause delays, the improvement of contracts and the precise and clearer definition of all elements of the project can help to reduce the duration of construction, and will allow companies to maintain sustainable activities in the construction industry.

In the realm of educational technology, Data Analytics (DA) is reshaping teaching and learning. This paper investigates the impact of DA on education, specifically comparing Student Information Systems (SIS) and Learning Management Systems (LMS). Data-driven insights from SIS and LMS platforms enable educators to tailor instructional strategies to individual student needs effectively. While SIS manages student data for administrative tasks, LMS offers tools for content delivery and collaboration. Using the strengths of SIS and LMS, educators can optimise teaching and learning experiences, tracking student progress, and fostering collaboration. The comparison emphasises their distinct roles: SIS manages administrative tasks, while LMS focusses on content delivery and collaboration. Using both systems, educators improve the teaching and learning experience, leveraging DA for continuous improvement. In summary, this paper underscores the transformative role of DA in education, framed within the context of comparing the SIS and LMS functionalities. By examining the intersection of data-driven decision making and educational technology, educators are equipped with the tools and knowledge to harness the power of data for meaningful and impactful teaching and learning.

Accurately estimating the pose of spacecraft is indispensable for space applications. However, such targets are generally non-cooperative, i.e., no markers are mounted on it and no parts for operation. Therefore, the detection and measurement of a non-cooperative target is very challenging. Stereovision sensors are important solutions in the near field. In this paper, a rectangular natural feature recognition and pose measurement method for non-cooperative spacecraft is proposed. Solar panels or the bodies of spacecraft are selected as detection objects and their image features are captured by stereo vision. These rectangle features are then reconstructed in 3D Cartesian space through parallelogram fitting on the image planes of two cameras. The vertexes are used to calculate the center position of the rectangle and the direction of the fixed coordinate system to solve the pose and attitude of the non-cooperative target. An experimental system is built to validate the effectiveness of the algorithm. The experimental results show that the average position measurement error of the algorithm is about 10mm and the average attitude measurement error is less than 1°. The results show that the proposed method has high accuracy and efficiency.

Due to the advantages of low latency, low power consumption and high flexibility of FPGA-based acceleration technology, it has been more and more widely studied and applied in the field of computer vision in recent years. An FPGA-based feature extraction and tracking accelerator for real-time visual odometry (VO) and visual simultaneous localization and mapping (V-SLAM) is proposed, which can realize the complete acceleration processing capability of the image front-end and directly output the feature point ID and coordinates to the backend. The accelerator consists of image preprocessing, pyramid processing, optical flow processing, and feature extraction and tracking modules. For the first time, it implements a hardware solution that combines features from accelerated segment test (FAST) corners with Gunnar Farneback (GF) dense optical flow, to achieve better feature tracking performance and provide more flexible technical route selection. In order to solve the scale invariance and rotation invariance lacking problem of FAST features, an efficient pyramid module with a five-layer thumbnail structure is designed and implemented. The accelerator is implemented on a modern Xilinx Zynq FPGA. The evaluation result shows that the accelerator can achieve stable tracking of features of violently shaking images, and is consistent with the results of MATLAB code running on PC. When operating at 100MHz, the accelerator can process 108 frames per second for 720P images and 48 frames per second for 1080P images. Compared to PC CPUs that consume seconds of time, the processing latency is greatly reduced to the order of milliseconds, making GF dense optical flow an efficient and practical technical solution on the edge side.

Skin cancer is an exquisite disease globally nowadays. Because of the poor contrast and apparent resemblance between skin and lesions, automatic identification of skin cancer is complicated. The rate of human death can be massively reduced if melanoma skin cancer can be detected quickly using dermoscopy images. In this research, an anisotropic diffusion filtering method is used on dermoscopy images to remove multiplicative speckle noise and the fast-bounding box (FBB) method is applied to segment the skin cancer region. Furthermore, the paper consists of two feature extractor parts. One of the two features extractor parts is the hybrid feature extractor (HFE) part and another is the convolutional neural network VGG19 based CNN feature extractor part. The HFE portion combines three feature extraction approaches into a single fused feature vector: Histogram-Oriented Gradient (HOG), Local Binary Pattern (LBP), and Speed Up Robust Feature (SURF). The CNN method also is used to extract additional features from test and training datasets. This two-feature vector is fused to design the classification model. This classifier performs the classification of dermoscopy images whether it is melanoma or non-melanoma skin cancer. The proposed methodology is performed on two ordinary datasets and achieved the accuracy 99.85%, sensitivity 91.65%, and specificity 95.70%, which makes it more successful than previous machine learning algorithms.

Background: Lung cancer is one of the common causes of death worldwide. Although the incidence rate of lung cancer in Western countries is decreasing, it presents a growing trend in developed countries. Since there is no accurate enough information about the epidemiological and Histopathologic features of lung cancer in central Iran, Isfahan, we were motivated to conduct this research. Materials and Methods: This was a descriptive, cross-sectional study carried out in central Iran, Isfahan. All demographic, histopathological and clinical data of the lung cancer patients registered in MACSA, a referral charity-based cancer center in central Iran, was analyzed within 2012-2018 using SPSS v.22 software. Results: Altogether 260 patients with lung cancer were included in this study from 6127 cancer patients registered within 2012-2018 (4.2%). Out of them, 66.2% were men, and 18.8 % of the patients were alive at the time of the study. The mean age of the patients at diagnosis was 61.56 (SD=14.11, range: 9-93). Altogether, 63.1% of patients had metastasis of whom 57.6% were in stage IV at diagnosis. The Frequency of different types of lung cancer was 36.9% adenocarcinomas, 14.2% squamous cell carcinoma, 9.6% bronchogenic carcinoma and 8.1% small cell lung cancer, respectively. Altogether, 128 cases were smokers with an average 35.45 ± 14 pack- years. Only in 36.2% of the patients, the diagnostic and therapeutic biomarkers had been checked, and CK7 was positive in 88.9% of the cases in which the biomarker had been checked. Conclusion: Despite to similar Iranian studies, the most common histopathologic type of lung cancer among the patients was adenocarcinoma that it may be attributed to the lower consumption of smoking in our population and their different genetic context. Molecular biomarkers had been checked in a small portion of the patients. More education of the clinicians along with the development of cancer molecular testing may lead to promote the personalized-based approach.

In recent years, governments applied intelligent transportation system (ITS) technique to provide several convenience services (e.g., garbage truck app) for residents. This study proposes a garbage truck fleet management system (GTFMS) and data feature selection and data clustering methods for travel time prediction. A GTFMS includes mobile devices (MD), on-board units, fleet management server, and data analysis server (DAS). When user uses MD to request the arrival time of garbage truck, DAS can perform the procedure of data feature selection and data clustering methods to analyses travel time of garbage truck. The proposed methods can cluster the records of travel time and reduce variation for the improvement of travel time prediction. After predicting travel time and arrival time, the predicted information can be sent to user’s MD. In experimental environment, the results showed that the accuracies of previous method and proposed method are 16.73% and 85.97%, respectively. Therefore, the proposed data feature selection and data clustering methods can be used to predict stop-to-stop travel time of garbage truck.

Containing hundreds of spectral bands (features), hyperspectral images (HSIs) have high ability in discrimination of land cover classes. Traditional HSIs data processing methods consider the same importance for all bands in the original feature space (OFS), while different spectral bands play different roles in identification of samples of different classes. In order to explore the relative importance of each feature, we learn a weighting matrix and obtain the relative weighted feature space (RWFS) as an enriched feature space for HSIs data analysis in this paper. To overcome the difficulty of limited labeled samples which is common case in HSIs data analysis, we extend our method to semisupervised framework. To transfer available knowledge to unlabeled samples, we employ graph based clustering where low rank representation (LRR) is used to define the similarity function for graph. After construction the RWFS, any arbitrary dimension reduction method and classification algorithm can be employed in RWFS. The experimental results on two well-known HSIs data set show that some dimension reduction algorithms have better performance in the new weighted feature space.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

Abstract: Urban regeneration decision-making is a complex process, as it involves a wide range of decision-makers, public-private partnerships in finance and implementation, including the inevitable considerable amount of risk on a long-term basis. There are a multitude of stakeholders, the citizens being the key stakeholders. It is necessary to involve the citizens in the planning process. Such involvement allows the communities to express their needs and aspirations, which is useful in the policymaking, delivery of planning programs, and in the monitoring process. In such a context, Factor analysis was the statistical technique used (1) Carry out factor analysis based on the principal component analysis method using the software XLSTAT 2021.4.1.1205 - (2) Construct a factor model of Urban Regeneration. (3) Interpret and label the factor dimensions. The results of the analysis indicated that the first two principal components accounted for 60.04% of the total variance of the original dataset. All variables seemed to be, positively correlated to each other and contributed similarly to principal components PC1 &PC2. The observations were well clustered; except for very few outliers. The limitation of the work was that the perceptions of the citizens were limited to the variables derived by the researcher.

The frame construction of an apartment complex that consists of multiple buildings encounters various uncertainties, owing to the complex relationships among units of work. Currently, the period of such a construction is calculated based on the number of floors of the highest building in the complex. This study quantitatively analyzes an apartment frame construction period using a queue model and evaluates the validity of the estimated period. In this regard, a methodology is proposed for analyzing the construction period by applying the concept of a customer and a server. A case study on the duration of an apartment frame construction is conducted with Korea Land and Housing Corporation, which has supplied the largest number of apartments in South Korea. It was found that the stable state of a queue system was observed when the rate of server utilization was applied to the basement and aboveground floors. However, a stable state was not reached on the ground floor. This study includes non-working days in its calculation and quantitatively analyzes uncertainty factors during construction. Therefore, the findings can be practically utilized to quantitatively plan the durations of work units in an apartment frame construction.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

The existence of palindrome numbers of arbitrary length greater than 2 that are divisible by the prime number 37 is proven in this paper. The method to construct such a palindrome is also described. It turns out that a palindrome number divisible by 37 is also divisible by 3 and, consequently, divisible by 111.

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

Cycle times at workstations in offsite construction factories fluctuate widely due to various influencing factors. Consequently, relying on average rates, such as length per unit of time, for estimating cycle times proves to be inaccurate, often leading to significant deviations between production schedules and actual operations. To address this issue, this study proposes an estimation system that leverages machine-learning-based prediction, statistical methods, 3D simulation, and computer vision to predict cycle times at the workstation level. Testing of the system on a semi-automated wood-wall framing workstation in a panelized construction factory shows that it reduces the mean absolute error and sum of errors by approximately 36% and 68%, respectively, compared to the fixed rate method. The results also highlight the efficacy of using computer vision data for training machine-learning models for cycle time estimation, the importance of identifying and understanding the factors influencing cycle times, and the impact of random delays on the accuracy of cycle time estimation systems.

With the advancement of the economy and society, policymakers acknowledge the significance of improving rural households' well-being as a crucial factor in promoting sustainable economic and social development. Based on the matching data of China Household Finance Survey and Digital Rural County Index, this study empirically examines the effect and mechanisms of digital village construction on subjective well-being of rural households. The results revealed that digital village construction has a significant improvement in their subjective well-being. The impact of digital village construction is particularly significant in rural areas located in the western regions of China, as well as among households possessing higher levels of human capital. The process through which digital village construction enhances the subjective well-being of rural households involves the augmentation of household income, the promotion of non-farm employment opportunities, and the enhancement of rural governance. This study provides robust micro-empirical evidence highlighting the positive welfare effects of digital rural construction. This study provides insights into the digital village construction within the happiness economy framework, offering a new perspective. The imperative to strengthen rural digital infrastructure and improve farmers' proficiency in modern information skills is a strategic policy aimed at enhancing well-being of rural households.

When an aircraft malfunctions, quickly and accurately identifying the faulty unit is essential for ensuring normal operation. Unfortunately, maintenance engineers often struggle to acquire the necessary fault-related knowledge due to poor management and utilization of aircraft fault documents. To address this issue, we introduce knowledge graph technology into the field of aircraft fault diagnosis, exploring its construction and application for effective knowledge management. Our work starts by analyzing the critical knowledge elements required for aircraft fault diagnosis and designing a schema layer for fault knowledge graphs. We then we then combine deep learning and heuristic rules to extract fault knowledge from both structured and unstructured data, enabling the construction of aircraft fault knowledge graphs. Finally, we develop a fault question-answering system based on fault knowledge graphs that can accurately give solutions to questions posed by maintenance engineers. Our practice demonstrates that knowledge graphs provide an effective means of managing aircraft fault knowledge, assisting engineers in locating fault reasons accurately and quickly.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

We report on the design and construction of a spin-flip Zeeman slower, quadrupole magnetic trap, and Feshbach fields for a new machine for ultra-cold Li-7. The small mass of the Li-7 atom, and the tight lattice spacing, will enable us to achieve a 100-fold increase in tuneling rates over comparable Rb-87 optical lattice emulator experiments. These improvements should enable to access new regimes in quantum magnetic phase transitions and spin dynamics.

Prefabricated forms of construction have led to the rapid onsite assembly of buildings however there are still on-site tasks and processes which can be reevaluated and redone specifically in keeping with the principles of prefabrication instead being adapted to fit its purpose. One such process is that of waterproofing between prefabricated panels and modules which come from the factory fully complete façade and all. Conventional means of waterproofing can be used however it results in more work done on site, potential delays and generally requires access from the external face of the building. This paper presents the Modelling, Implementation and Evaluation of purpose developed weatherproof seals specific for Prefabricated Construction. An overview is provided of the entire development process and specific focus is given to the modeling using FEA computer simulations, manufacturing and testing which then resulted in the implementation in a prefabricated panelised building which is used as a case study and the means of further evaluation. These strategies have enabled an efficient and robust prefabricated waterproofing solution specific for this form of construction to be understood and implemented. The resulting case study has successfully verified the time and cost savings when compared to conventional techniques whilst still providing a durable and effective weatherproof seal for prefabricated panelised and modular systems.

Tuning tensor program generation involves navigating a vast search space to find optimal program transformations and measurements for a program on target hardware. The complexity of this process is further amplified by the exponential combinations of transformations, especially in heterogeneous environments. This research addresses these challenges by introducing a novel approach that learns the joint neural network and hardware features space, facilitating knowledge transfer to new, unseen target hardware. A comprehensive analysis is conducted on the existing state-of-the-art dataset, TenSet, including a thorough examination of test split strategies and the proposal of methodologies for dataset pruning. Leveraging an attention-inspired technique, we tailor the tuning of tensor programs to embed both neural network and hardware-specific features. Notably, our approach substantially reduces the dataset size by up to 53% compared to the baseline without compromising Pairwise Comparison Accuracy (PCA). Furthermore, our proposed methodology demonstrates competitive or improved mean inference times with only 25%40% of the baseline tuning time across various networks and target hardware. The attention-based tuner can effectively utilize schedules learned from previous hardware program measurements to optimize tensor program tuning on previously unseen hardware, achieving a top-5 accuracy exceeding 90%. This research introduces a significant advancement in auto-tuning tensor program generation, addressing the complexities associated with heterogeneous environments and showcasing promising results regarding efficiency and accuracy.

In the chemical processing industries, sensors for pumps are among the most commonly used machinery. Condition-based maintenance (CBM) and prognosis health management (PHM) determine the most cost-effective time to overhaul pumps. In order to determine the status of the pump, a signal-emitting accelerometer is employed. Stationarity-based feature extraction from amplitude signals is used to process the signal. Utilizing the time-domain function, multiple statistical results were produced. Eight fault codes were classified using support vector machine method. The enormous amount of data points necessitated the use of feature selection. In terms of accuracy, precision, recall, and F1 score, the Chi-square feature selection method exceeds other approaches.

By applying a running average (with a window-size= d), we could transform Discrete data to broad-range, Continuous values. When we have more than 2 columns and one of them is containing data about the tags of classification (Class Column), we could compare and sort the features (Non-class Columns) based on the R2 coefficient of the regression for running averages. The parameters tuning could help us to select the best features (the non-class columns which have the best correlation with the Class Column). “Window size” and “Ordering” could be tuned to achieve the goal. this optimization problem is hard and we need an Algorithm (or Heuristics) for simplifying this tuning. We demonstrate a novel heuristics, Called Simulated Distillation (SimulaD), which could help us to gain a somehow good results with this optimization problem.

The objective to fast-track the mapping and registration of large numbers of unrecorded land rights globally, leads to the experimental application of Artificial Intelligence (AI) in the domain of land administration, and specifically the application of automated visual cognition techniques for cadastral mapping tasks. In this research, we applied and compared the ability of rule-based systems within Object Based Image Analysis (OBIA), as opposed to human analysis, to extract visible cadastral boundaries from Very high resolution (VHR) World View-2 image, in both rural and urban settings. From our experiments, machine-based techniques were able to automatically delineate a good proportion of rural parcels with explicit polygons where the correctness of the automatically extracted boundaries was 47.4% against 74.24% for humans and the completeness of 45% for machine, as against 70.4% for humans. On the contrary, in the urban area, automatic results were counterintuitive: even though urban plots and buildings are clearly marked with visible features such as fences, roads and tacitly perceptible to eyes, automation resulted in geometrically and topologically poorly structured data, that could neither be geometrically compared with human digitised, nor actual cadastral data from the field. These results provide an updated snapshot with regards to the performance of contemporary machine-drive feature extraction techniques compared to conventional manual digitising.

Convolutional neural networks (CNNs) face challenges in capturing long-distance text correlations, and Bidirectional Long Short-Term Memory (BiLSTM) networks exhibit limited feature extraction capabilities for text classification of work order. To address the abovementioned problems, this work utilizes an ensemble learning approach to integrate model elements efficiently. This study presents a method for classifying work order texts using a hybrid neural network model called BERT-BiLSTM-CNN. First, use Bert for preprocessing to obtain text vector representations. Then, capture context and process sequence information through BiLSTM. Next, capture local features in the text through CNN. Finally, obtain classification results through Softmax. Through comparative analysis, the method of fusing these three models is superior to other hybrid neural network model architectures in multiple classification tasks. It has a significant effect on work order classification.