The rapid expansion of livestock production sector to meet the world population demand is posing a big challenge to environmental sustainability. Plant-based feed additives extracted from food by-products could potentially result in a double outcome: improving animal zootechnical performances and mitigating environmental impacts of meat production chains. This presented study was carried out to assess the environmental impacts of the supplementation of a commercial Citrus extract feed additive (CEFA) in swine and broiler farming. Life cycle assessment (LCA) was applied to assess the impact of manufacturing and distributing 1 bag of 25 kg of CEFA and its use in feed in broiler and swine productions. With regard to CEFA manufacturing and distribution, results showed that the majority of impact came from the production of CEFA ingredients, accounting for 70% impact generated. The remaining 30% effect was divided to transportation to customer (25%), CEFA packaging (3%), CEFA manufacture, and production loss (2%). When enlarging the scope, the use of CEFA in piglet and broiler diets showed improving the measured environmental indicators, compared to such standard systems. Indeed, feed supplemented CEFA have demonstrated in elevating zootechnical performances, hence saving feed consumed. Consequently, that helped reduce environmental issues from animal feed ingredients’ agriculture. To be more specific, the supplementation of 25 kg of CEFA in feed led to a reduction of 6 tons of CO2 emitted along the life cycle of broiler production and 5 tons in the case of fattening pig. 0.7 hectares of land used had been saved as well as, 201 m3 of water (broiler) and 82 m3 (swine) were economized. Environmental performance assessment showed the interest in using this CEFA in swine and broiler diets to mitigate the environmental impacts.

The extrusion-based additive manufacturing is a popular fabrication method, which has attracted the attention of various industries due to its simplicity, cheapness, ability to produce complex geometric shapes, and high production speed. One of the effective parameters in this process is the feed of filament that is presented in the production G-code. The feed of filament is calculated according to the layer height, the extrusion width and the length of printing path. All the required motion paths and filling patterns created by commercial software are a set of straight lines or circular arcs that are placed next to each other at a fixed distance. In special curved paths, the distance of adjacent ones is not equal at different points, and due to the weakness of common commercial software, it is not possible to create curved paths for proper printing. Therefore, making a special computer code that can be used to create various functions of curved paths is investigated in this research, and also the feed of filament parameter is studied in detail. Next, by introducing a correction technique, the feed of filament is changed during the curved path to distribute the polymer material uniformly. Finally, composite samples (which have variable stiffness) consisting of curved fibers are produced with the proposed method, and the high quality of printed samples confirm the suggested code and technique.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Regulation of the diet in terms of the content of soluble and insoluble fibre is of great importance from the point of view of dietetics, microbiology of the gastrointestinal tract and immunology of the organism. Dietary fibre plays an important role in maintaining the balance between the con-tinuity of gut mucus production (intestinal mucosa), the stability of the intestinal microbiome composition, the regeneration of the intestinal epithelium and the immune status within the gut-associated lymphoid tissue (GALT) are played by pectin and their metabolic products in the form of pectin oligosaccharides. The main purpose of this review was to focus on pectin, their functions, their impact on the human's health and on some of the most promising prebiotics due to their solubility in the gastrointestinal tract in the form of pectin oligosaccharides. They have the properties of pectin, but have also additional features and postbiotics obtained in fermentation process can affect the intestinal microbiome and GALT-related immunity. They can be obtained from plant agro-wastes.

This study aimed to determine the impact of a novel formulation of a supplement composed of the natural ingredients: bromelain, quercetin, and Lentinula edodes, on the gut microbiota of healthy adult dogs. Adult healthy female dogs were administered either a placebo (CTR, n = 15) or the supplement (TRT, n=15) over 28 days. Stool samples were collected for 16S rRNA sequencing before supplement administration (T0), at completion of supplement administration (T28), and one week after the end of supplement administration (T35) to characterize changes in the gut microbial communities. QIIME was used to determine both alpha- and beta-diversity and ANCOM-BC was used to identify differences in taxonomic abundances before and after supplementation. We found a significant decrease in overall diversity in CTR group, but no significant differences in overall diversity in the TRT group over time. Furthermore, we found differences in the abundance of several taxa in both CTR and TRT groups but differences in abundance of beneficial bacteria were more pronounced in TRT group. Specifically, we found increases in the abundance of sequences belonging to the genera Bifidobacterium, Lactobacillus, and Pediococcus at T28 in the TRT group with significant increases in Bifidobacterium and Lactobacillus persisting at T35 when compared to T0. Importantly, members of these genera are known to be pro anti-inflammatory and associated with a healthy gut microbiota in dogs. The results of our study show the potential of our supplement to selectively enhance specific beneficial bacterial taxa, offering a targeted approach to modulating the gut microbiome without causing disruptions to the overall equilibrium.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

Aquaculture contributes to the sustainable development of food security, marine resource conservation, and economy. Shifting aquaculture feed from fish meal and oil to terrestrial plant-derivatives may result in cost savings. However, many carnivorous fish cannot be sustained on plant-derived materials, necessitating the need for the identification of important factors for farmed fish growth and to investigate whether components derived from terrestrial plants can be used in feed. Herein, we focused on the carnivorous fish leopard coral grouper (P. leopardus) to identify the essential growth factors and clarify their intake timing from feeds. Furthermore, we evaluated the functionality of starch, which are easily produced by terrestrial plants. Results reveal that carbohydrates, which are not considered essential for carnivorous fish, can be introduced as a major part of artificial diet. The development of artificial feed using starch offers the possibility of increasing the growth of carnivorous fish in aquaculture.

This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

As most prominent plant-associated disease, photosensitization in large herbivores provides a substantial data base to evaluate the conditions under which animals are concerned. The purpose of this meta study was to investigate whether the level of feed plant diversity and feed choice influence the incidence of photosensitization. Case reports from 1900 to 2022 served as database. 113 publications described 178 cases of altogether 12 animal species, most of them being farm animals. 73.6% of the cases originated from three continents: South America, Australia and North-America. Of the 40 phototoxic agents, herbs represented the majority (63.6%). Brachiaria, Froelichia and other four genus were associated in almost 50% of the cases. Usually, animals received feed both of normal quality and in fresh state. Secondary photosensitization was most frequent only when associated with poor feed quality. If the animals had had access to high-diversity feed instead of low-diversity feed, the incidence was 27.5% smaller. If the animals had the choice between various kind of feed, the incidence was even reduced by 56.1%. Horses could select the least, however, suffered mainly from primary photosensitization. We conclude that farmers may prevent photosensitization in husbandry animals by allowing both more feed choice and feed diversity.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

This preprint is focused in the presence of plastics and microplastics in food. We will discuss how many we eat, and how they arrive to the food, and why. We will treat many other things, such as the waste treatment in Europe and in Spain, with updated data; how much plastic waste is generated; what are microplastics and how they are analyzed, I will tell about the experience we have at the University of Alicante (UA); how they can be removed and we will estimate how many we eat over the course of a year.

This article explores the emerging concept of atrial myopathy (AM) and its potential role as a risk factor for stroke and dementia, both independently and in association with atrial fibrillation (AF). AM refers to structural and functional abnormalities of the atria, potentially causing blood clots formation and their subsequent embolization even in patients without AF. Echocardiography, particularly Left Atrial (LA) strain analysis, is a promising non-invasive tool for AM evaluation and might offer additional risk stratification beyond the established CHADS2-VASc score, potentially impacting anticoagulation decisions. By understanding AM and utilizing advanced imaging techniques like LA strain, clinicians can achieve a more comprehensive understanding of thromboembolic risk in specific patient groups. Integrating LA strain analysis into routine clinical practice holds promise for improved patient management and targeted therapies, allowing for better risk stratification in AF patients. However, standardized definitions and diagnostic criteria for AM are essential for consistent evaluation and research. Further studies are needed to explore the efficacy and safety of anticoagulation in AM patients without AF.

Soybean a pulse of considerable nutritional value due to its high protein, fibers and polyunsaturated fatty acid (PUFA) contents, also contains phytoestrogenic compounds that definitely hinder its recommendation for general consumption. Contrarily to ancient times when soybeans were boiled, modern commercial soy-foods can contain up to 150 mg/100g of estrogenic isoflavones. Interestingly, current estimations of isoflavone intake in the literature do not distinguish between the origins of soy-food i.e. home-made or commercial. As a result, the isoflavone exposure in Asian countries may well be over-estimated. This study aims to demonstrate, based on step-by-step monitoring of isoflavones, that traditional and domestic treatments, leveraging isoflavones water-solubility, can indeed significantly reduce their content in soy-foods. Indeed, when compared to commercial foods, the isoflavone contents was found to be 20, 2.6, 4.5 and 9.8 times lower in “home-made” soy-juice, tofu, tempeh and miso, respectively. Additionally, water soaking was found to reduce the isoflavones levels in soy-textured-proteins by more than 70%. Hence, this simple process has the potential to help drastically reduce overall xenoestrogens exposure. This study could serve as a basis for establishing the isoflavones Reference Dose and issuing food safety guidelines.

No system nor standardized analytical procedures at commercial laboratories exist to facilitate and accurately measure potential viable virus contamination in feed ingredients and complete feeds globally. As a result, there is high uncertainty of the extent of swine virus contamination in global feed supply chains. Many knowledge gaps need to be addressed to improve our ability to prevent virus contamination and transmission in swine feed. This review summarizes the current state of knowledge involving: 1) the need for biosecurity protocols to identify production, processing, storage, and transportation conditions that may cause virus contamination of feed ingredients and complete feed, 2) challenges of measuring virus inactivation, 3) virus survival in feed ingredients during transportation and storage, 4) minimum infectious doses, 5) differences between using a Food Safety Objective versus a Performance Objective as potential approaches for risk assessment in swine feed, 6) swine virus inactivation from thermal and irradiation processes, and chemical mitigants in feed ingredients and complete feed, 7) efficacy of virus decontamination strategies in feed mills, 9) benefits of functional ingredients, nutrients, and commercial feed additives in pig diets during a viral health challenge, and 10) considerations for improved risk assessment models of virus contamination in feed supply chains.

Forty-five of intact three sheep breeds (Awassi, Harri, and Najdi) were used in this study (15 animals of each breed), with weight ranged from 23.40 to 25.87 kg. Five animals from each group at the end of growth trial were used for digestibility and nitrogen balance trials. The three groups of sheep had effect (p > 0.05) in the final live weight (FLW). Average daily feed intake (ADI), average daily gain (ADG) and feed conversion ratio (FCR) were significantly (p < 0.05) different among the three groups. For digestibility coefficients, the three breeds of sheep had no effect (p > 0.05) in dry matter (DM), organic matter (OM), crude protein (CP), crude fiber (CF), nitrogen free extract (NFE), neutral detergent fiber (NDF) and acid detergent fiber (ADF). In the similar approach, no significant differences were founds among three breeds of sheep in digestible organic matter, digestible of crude protein, total digestible nutrients and nitrogen retention. The current study concluded that the sheep breeds affected average daily feed intake, average daily gain and feed conversion ratio (FCR). Awassi breed showed the best of average daily gain and feed conversion ratio followed by Najdi then Harri breeds. The breed of sheep had no effect on digestibility coefficients and nitrogen retention.

The aim of the present trial was to evaluate the growth performance of buffalo calves fed diets characterized by different forage/concentrate ratio with or without the Saccharomyces Cerevisiae supplementation (CBS 493.94, Yea-Sacc®). Twenty-four male buffalo calves (mean age 145.1 ± 16.1 days; mean weight 108.0 ± 18.7) were assigned randomly to 4 groups, homogeneous for age, fed four different diets: diet 1 F:C ratio 50:50; diet 2 F:C ratio 30:70; diet 3 F:C ratio 50:50 + Yea-Sacc® and diet 4 F:C ratio 30:70 + Yea-Sacc®. Buffalo calves were individually weighted before the start of the experiment and the data were used as a covariate, monthly until the end of the trial. Dry matter intake (DMI), daily weight gain (DWG) and feed conversion ratio (FCR) were calculated. The differences in diets’ composition significantly (p

The feed-forward loop (FFL) is an important and basic network motif to understand specific biological functions. Cyclic-AMP (cAMP) receptor protein (CRP), a transcription factor (TF), mediates catabolite repression and regulates more than 400 genes in response to changes in intracellular concentrations of cAMP in Escherichia coli. CRP participates in some FFLs like araBAD and araFGH operons and adapt to fluctuating environmental nutrients thus enhancing the survivability of E. coli. Although computational simulations have been used to explore the potential functionality of FFLs, a comprehensive study of the functions of all structural types based on in vivo data is lacking. Also, the regulatory role of CRP-mediated feed-forward loops (CRP-FFLs) remain unclear to date. Using EcoCyc and RegulonDB, we identified 393 CRP-FFLs in the E. coli. Dose-response genomic microarray of E. coli revealed dynamic gene expression of each target gene of CRP-FFLs in response to a range of cAMP dosages. All eight types of FFLs were present in CRP regulon with various expression patterns of each CRP-FFL, that were further divided into five functional groups. Microarray and reported regulatory relationships identified 202 CRP-FFLs which were directly regulated by CRP in these eight types of FFLs. Interestingly, 30% (147/482) of genes were directly regulated by CRP and CRP-regulated TFs, indicating that these CRP-regulated genes were also regulated by other CRP-regulated TFs responding to environmental signals through CRP-FFLs. Furthermore, we applied gene ontology annotation to reveal the biological functions of CRP-FFLs.

Nitrate and nitrite are the most extensively used food additives in the food industry for their multifunctional properties, and they have been in the spotlight for decades for its controversial back effects. The conversion of nitrate and nitrite to various nitroso compounds, specifically N-nitrosamine raises the question of the integrity of these additives. Nitrosamine is a well-known carcinogen and mutagen. A large number of studies demonstrate the carcinogenic effects of these salts. Are these findings credible? Nonetheless, the regulatory agencies approve its usage; is it biased? Are we feeding on the carcinogens in processed foods? The current work provides an insight into the basic and toxicological findings of the food additives -nitrate and nitrite.

The paper delves into an extensive exploration of the integration of the circular economy paradigm within the realm of additive manufacturing (AM). The objective is to comprehensively investigate existing methodologies for structuring the symbiotic relationship between circular economy and additive manufacturing, while meticulously analyzing the current research gap concerning the implementation of circular economy principles in additive manufacturing practices. A thorough review focusing on the sustainability of additive manufacturing within the circular economy framework was conducted. This review aims to recognize and delineate pertinent aspects related to post-use material valuation in AM, recyclability of materials, and the environmental footprint associated with these processes. Emphasis was placed on the significance of examining circular economy facets concerning additive manufacturing processes to establish a holistic understanding. The overarching goal of this review is to augment knowledge regarding the potential advantages and benefits derived from the seamless integration of circular economy principles within AM. By elucidating the activities essential to attain compliance with the Sustainable Development Goals, this study endeavors to illuminate the pathway toward promoting sustainable development through the harmonious marriage of additive manufacturing and the circular economy.

China faces a persistent deficiency in feed protein resources. Enhancing the utilization efficiency of indigenous feed protein resources emerges as a viable strategy to alleviate the current deficit in protein feed supply. Corn gluten meal (CGM), characterized by high proportion of crude protein and glutamine, is predominantly employed in animal feed. Nonetheless, the water-insolubility of CGM protein hampers its protein bioavailability when utilized as feed material. This study aimed to augment protein bioavailability, liberate glutamine peptides from CGM, and produce gluta-mine-enriched CGM fermented feed. We executed a co-fermentation protocol using Bacillus subtilis A5, Lactobacillus 02002, and acid protease to generate the CGM fermented feed. Subsequent in vivo experiment with broilers were conducted to assess the efficacy of the fermented product. Findings revealed that the soluble protein, glutamine, small peptides, and lactic acid contents in the fer-mented feed increased by 69.1%, 700%, 47.6%, and 125.9%, respectively. Incorporating CGM fermented feed into the diet markedly enhanced the growth performance and intestinal health of broilers, positively modulated the cecal microbiota structure, and augmented the population of beneficial bacteria, specifically Lactobacillus. These results furnish both experimental and theoretical foundations for deploying CGM fermented feed as an alternative protein feed resource.

The use of anti-microbial drugs and coccidiostats in poultry farming is widespread, with a significant proportion of these drugs being excreted and released into the environment. The residues of such drugs in poultry litter (PL) can result in the development of antibiotic-resistant bacteria. The impact of different biotic treatments (aerobic, anaerobic, and stacking) on broiler litter (BL) before use as animal feed has not been studied extensively, nor have the differences between antimicrobial-dependent and independent broiler farms been investigated. This study aimed to determine the resistant bacteria in BL used as ruminant feed before and after litter treatment. The results showed that the most resistant bacteria before BL treatment were Enterococcus species. The study also found that the quantity of amoxicillin-resistant Enterococcus detected in samples from antimicrobial-dependent farms was significantly higher than in those from antimicrobial-independent farms. Additionally, 14% of bacteria were multi-resistant to tetracycline, sulfafurazole, and erythromycin in antimicrobial-independent farm litters, significantly lower than those measured in antimicrobial-dependent broiler farm litter. This study highlights the importance of better understanding, regulating, managing, and using animal waste appropriately to reduce the number of antibiotic-resistant bacteria and minimize the use of antimicrobials that carry high risks for animals, humans, and the environment

Ruminant animals naturally emit methane gas owing to anaerobic microbial fermentation in the rumen, and these gases are considered major contributors to global warming. Scientists worldwide are attempting to minimize methane emissions from ruminant animals. Some of these attempts include the manipulation of rumen microbes using antibiotics, synthetic chemicals, dietary interventions, probiotics, propionate enhancers, stimulation of acetogens, manipulation of rumination time, vaccination, and genetic selection of animals that produce low methane (CH4). The majority of synthetic additives are harmful to both beneficial rumen microbes and the host or only temporarily affect methanogenesis. Phytogenic feed additives (PFAs) have recently emerged as the best alternatives to antibiotics and synthetic chemicals because of growing public concerns regarding drug resistance and the negative impacts of antibiotics and synthetic chemicals on humans, livestock, and the environment. These additives reduce methane production and improve the volatile fatty acid profile. In this review, we provide an overview of PFA sources and how their bioactive components affect the rumen microbiome to reduce methane emissions. Additionally, we highlight the mechanisms of action of PFAs as a whole as well as some of their bioactive components.

Additive manufacturing (AM) provides opportunities to design objects differently than traditional manufacturing methods allow, but only if designers understand the possibilities AM presents. In this study, we examined whether an AM workshop combined with an idea generation session could inspire engineering professionals to use AM solutions to solve current technical problems they face. All subjects were employees at an organization that will be referred to as Company X, a multinational commercial organization based in North America. During the study, we collected ideas for 24 projects generated before and after a training workshop focused on design for AM. In the workshop, we provided three hours of instruction about design for two metal-based AM processes. The participants’ ideas were assessed using four specific metrics: (1) cost, (2) time,(3) completeness of solution, and (4) quality, which was a function of feasibility, usefulness, and novelty. Using these data, we explored whether the workshop was effective in inspiring the participants to use AM methods and techniques from AM research in their concept generation and whether participants’ AM solutions showed improvement in cost, implementation time, and quality over non-AM designs generated before the workshop.

This paper provides an overview of the new CPAM Project on Additive Manufacturing (AM) in design and simulation, focusing on topology & lattice structure optimization for a light-weighting advantage. This industry/academia collaboration project aims to utilize existing hardware and software tools, and investigate the practical limits of the technologies, providing eventual guidelines for general use. This will provide a solid foundation for the practical use of metal AM optimized solid and latticed structures especially for Ti6Al4V parts. Two case studies are demonstrated here, one a purely topology optimized design, and one also incorporating lattice optimized design, both from Ti6Al4V and load-bearing components, to be utilized in the Nelson Mandela University (NMU) Eco-Car Project in competition, late in 2018. This paper presents the Design for Additive Manufacturing (DfAM) process, the challenges met iro applying a DfAM design mindset, and a unique final voxel-based smoothing step finishing off the design process. Detailed structural integrity assessment of these parts are included - the question remains: can Additive Manufacturing help win the race?

The transportation of feed pellets via pneumatic conveying plays an improtant role in feed industry. In recent years, many efforts are made both exprimentally and numerically to gain a better understanding of the underlying mechanism for pneumatic conveying. Though few of those research is directly related to feed pellets, it can be beneficial to draw a full picture of rencent development in pneumatic conveying, with emphasis on aspects extendable to feed transportation. This paper reviews first the major factors concerning feed pellets pneumatic conveying, such as particle breakage, pipe wear and electrostatic. Building on that, new advancement including emerging new technologies in experiments and simulations are discussed, with a focus on the experimental measurements and mathematical models, repectively. The needs for future research and the analogy to feed pellets tranportation is given lastly.

We demonstrate a new quantitative method to the sieve of Eratosthenes, which is an alternative to the sieve of Legendre. In this method, every element of a given set is sifted out once only, and therefore, this method is free of the Mobius function and of the parity barrier. Using this method, we prove that every sufficiently large even number is the sum of two primes, and that every even number is the difference of two primes in infinitely many ways.

Additive manufacturing (AM) has revolutionized the field of biopolymers by providing a range of opportunities to create complex and intricate structures. Here we provide an overview of developments in biopolymer AM, first in the context of how natural systems have impacted the synthetic processes of AM, and secondly in the context of how synthetically derived structures can be used for biomedical applications. In particular, we explore the range of biopolymers developed for AM, AM techniques for biopolymers, and potential biocompatible medical applications with a focus on four categories of tissue in the human body: skin, bone, heart, and nerve. Despite the current challenges of the technology, exciting results in tissue regeneration, synthetic replacements for natural grafts, and complex dynamic organoids have already come to pass - with many more possible in the future.

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

The recent decade has witnessed the evolution of a novel paradigm of alloying which is based on utilising multiple elements to design compositionally complex alloys also known as high entropy alloys (HEAs). Conventional manufacturing of HEAs has a number of drawbacks, especially in terms of mechanical properties and design complexities. This has been addressed by additive manufacturing (AM), which has not only led to the fabrication of complex-shaped HEA components but has also enabled both ex-situ and in-situ tailoring of alloy microstructures. Considering the increasing interest in AM-based fabrication of HEAs in the last ten years, the present chapter is aimed at highlighting the present status and challenges in the avenue of AM of HEAs. This has been followed by a discussion on the recent trends in the avenue of AM-based fabrication of HEAs from the viewpoints of (i) microstructure evolution and mechanical properties, and (ii) alloy fabrication techniques. The chapter ends with a discussion on the future prospects in the aforementioned avenue.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

Metal Additive Manufacturing (MAM) has emerged as a promising technology in the aerospace industry, enabling the production of complex components with enhanced design flexibility and reduced lead times. Concurrently, Industry 4.0 has gained significant attention for its potential to revolutionize aerospace manufacturing processes. The paper aims to cluster and review the literature on MAM in the aerospace industry, specifically focusing on its relevance to Industry 4.0 and its applicability throughout the various stages of the product life cycle for the chief purpose of matching supply with demand. Identified gaps and challenges are analyzed, highlighting the need for further research and outlining research agenda aimed at advancing the integration of MAM for Industry 4.0 in the aerospace sector. By addressing these research areas, the aerospace industry can unlock the value of MAM within an Industry 4.0 framework, leading to improved efficiency, productivity, and competitiveness.

Porous structured metallic implants are preferable as bone graft substitutes due to their faster tissue integration mediated by bone in-growth and vascularization. The porous scaffolds/ implants should also mimic the graded structure of natural bone to ensure a match of mechanical properties. This article presents a method to design graded porous structured acetabular implant and identifies the suitable parameters for manufacturing the model through additive manufacturing. The design method is based on slice-wise modification to ensure continuity of gradation. Modification of the slices was achieved through the binary image processing route. A geodesic dome type design was adopted for developing the acetabular cup model from the graded porous structure. The model had a solid shell with the target porosity and pore size gradually changing from 65% and 950 µm, respectively, in the inner side to 75% and 650 µm, respectively, towards the periphery. The required dimensions of the unit structures, and the combinations of pore structure and strut diameter to obtain the target porosity and pore size were determined analytically. Suitable process parameters were identified to manufacture the model by Direct Metal Laser Sintering (DMLS) using Ti6Al4V powder after carrying out a detailed experimental study to minimize the variation of surface roughness and warping over different build angles of the strut structures. A dual contour scanning was implemented to simplify the scan strategy. The minimum diameter of struts that could be manufactured using the selected scanning strategy and scanning parameters was found to be 375 µm. Finally, the model was built and from the micro-CT data, the porosities and pore sizes were found to be closely conforming to the designed values. The stiffness of the structures, as found from compression testing, was also found to be well matching with that of human trabecular bone. Further, the structure exhibited compliant bending-dominated behavior under compressive loading.

Additive manufacturing has already been established as a highly versatile manufacturing technique with demonstrated potential to completely transform conventional manufacturing in the future. The objective of this paper is to review the latest progress and challenges associated with the fabrication of multi-material parts using additive manufacturing technologies. Various manufacturing processes and materials used to produce functional components were investigated and summarized. The latest applications of multi-material additive manufacturing (MMAM) in automotive, aerospace, biomedical and dentistry field were demonstrated. Investigation on the current challenges were also carried out to predict the future direction of MMAM processes. It is concluded that the further research and development needed in the design of multi-material interfaces, manufacturing processes and material compatibility of MMAM parts are necessary.

(1) In recent ten years, with the fast development of digital and engineering manufacturing technology, additive manufacturing has already been more and more widely used in the field of dentistry, from the first personalized surgical guides to the latest personalized restoration crowns and root implants. (2) Especially, the bioprinting of teeth and tissue is of great potential to realize organ regeneration and finally improve the life quality. (3) In this review paper, we firstly presented the workflow of additive manufacturing technology. Then we summarized main applications and recent research progresses of additive manufacturing in dentistry. (4) Lastly, we sketched out some challenges and future directions of additive manufacturing technology in dentistry.

The development of modern genomic tools has sped up the breeding program of food crops. More recently, genomic resources are being developed for tropical forages and will be key resources for developing climate resilient high yielding forage varieties. In this study, we present a genome-wide association study for biomass yield and feed quality traits in buffel grass (Cenchrus ciliaris L. aka Pennisetum ciliare L.,). Genome-wide markers generated using the DArTSeq platform and mapped onto the reference genome of Setaria italica were used for the genome-wide association study. The results revealed several markers associated with biomass yield and feed quality traits. A total of 78 marker trait associations were identified with R2 values ranging from 0.138 to 0.236. The marker trait associations were distributed across different chromosomes. Of these associations, the most marker trait associations (23) were observed on Chr9, followed by Chr5 with 12. The fewest number of marker trait associations were observed on Chr4 with 2. In terms of traits, 17 markers were associated with biomass yield, 24 with crude protein, 26 with TDN, 14 with ADF, 10 with NDF and six with DMI. Twenty of the identified markers were associated with at least two traits. The identified marker trait associations provide a useful genomic resource for future improvement and breeding of buffel grass.

To explore the forage quality of wild oat populations under different growth environments, the basic nutrient composition and forage quality of five wild oat populations in Israel were compared. Ash, crude protein, and soluble sugar content of oats were significantly (P<0.05) related to some forage quality and possible environment of population origin. Among them, the environmental factors of origin had significant effects on the indicators of ash, crude protein, and soluble sugars of oat straw, but less on the contents of crude fat, total phosphorus, and total potassium. Meanwhile, the annual rainfall and the number of days of rainfall in the country of origin greatly influenced the cellulose content. Finally, we investigated the similarity of feeding values of different populations using PCA analysis. The results showed that, in conclusion, the higher variability of wild oat populations may be a new possibility brought by feeding oats.

Among other species, Black Soldier Fly (Hermetia illucens, HI, Diptera, Stratiomydae) has the great potential as food and feed ingredient in the EU, particularly thanks to its preference for organic waste as growth substrate. The production of insects as livestock feed or as food ingredient requires a strict monitoring of heavy metal content in the growth substrate in order to secure its safe. This study aims to investigate the presence of toxic metals cadmium, lead, mercury, arsenic, and nickel in HI prepupae and their growth substrates based on coffee roasting by-product and microlagae Schizochytrium sp. and Isochrysis sp. Analyses were carried out via graphite furnace atomic absorption spectrophotometry for Cd, Pb, Ni, and As, and via Direct Mercury Analyzer for Hg. All metal concentrations found in growth substrates were below the legal limit of undesirable substances in animal feed (2002/32/EC). Metals concentrations in HI prepupae were in the range (mg kg-1 wet weight): Cd 0.072–0.084, Pb 0.018–0.026, Hg 0.010–0.032, As 0.036–0.047, Ni 0.18–0.76. HI prepupae accumulate Cd, Pb and Hg, but our results indicate that the risk of exposure to metals from consumption of HI prepupae is relatively low and in compliance with European Union regulations.

This mini-review provides an overview of traditional, emerging, and future applications of lactic acid bacteria (LAB) and discusses how genome editing tools can be used to overcome current challenges in all these applications. It also describes currently available tools and how these can be further developed, and takes current legislation into account. Genome editing tools are necessary for the construction of strains for new applications and products, but can also play a crucial role in traditional ones, such as food and probiotics, as a research tool for understanding mechanistic insights and discovering new properties. Traditionally, recombinant DNA techniques for LAB have strongly focused on being food-grade, but they lack throughput and the number of genetically tractable strains is still rather limited. Further tool development in this direction will enable rapid construction of multiple mutants or mutant libraries on a genomic level in a wide variety of LAB strains. We also propose an iterative Design-Build-Test-Learn workflow cycle for LAB cell factory development based on systems biology, with “cell factory” expanding beyond its traditional meaning of production strains and making use of high-throughput genome editing tools to advance LAB understanding, applications and strain development.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Additive Manufacturing and nanotechnology have been used as basic tools for the manufacture of nanostructured parts with magnetic properties to expand the variety of applications in additive processes by tank photopolymerization. Magnetic cobalt ferrite (CoFe2O4) and barium ferrite (BaFe12O19) nanoparticles with the size distribution of average value DTEM of 12 ± 2.95 nm and 37 ± 12.78 nm, respectively were generat-ed by hydroxide precipitation method. The dispersion of the nanoparticles on commercial resins (Anycubic Green and IRIX White resin) was obtained by mechanochemical reactions carried out in an agate mortar for 20 minutes, at room temperature and with limited exposure to light. The product of each reaction was placed in amber vials, also being kept in a box, to avoid contact with light. The photopolymerization process was carried out only at low concentrations (w/w % nanoparticles/resin) since, at high concentrations, there is no for-mation of pieces due to the high refractive index of ferrites. Raman shift spectroscopy of the final pieces showed that they contain the magnetic nanoparticles, with no apparent chemical changes. The EPR results of the pieces maintain the magnetic properties and apparently, they are not modified during the photopolymer-ization. Although significant differences were found in the dispersion process of the nanoparticles in each piece, we determined that the photopolymerization did not influence the structure and superparamagnetic behavior of ferrite nanoparticles during processing, and the magnetic properties were successfully transferred to the final 3D-printed magnetic obtained piece.

Additive manufacturing (AM) technologies show potential for the development of functionally integrated lightweight designs, biomimetic structures and material savings. Typically, as-built surfaces show powder particle agglomerations and re-entrant features, leading to rough surfaces, which are associated with poor fatigue performance. To benefit from the full range of advantages with special focus on aerospace applications, critical features for crack initiation when subjected to fatigue loading need to be identified and mitigated. A first step toward achieving this goal is the surface texture characterisation based on the quantification of surface features. In this paper, selected areal height, functional and feature parameters from ISO 25178-2:2022 are generated and process-specific features are examined for as-built AlSi7Mg0.6 from laser powder bed fusion (PBF-LB). A connection with the particle size distribution of the used powder is demonstrated. It is shown that surface feature analysis opens up opportunities to use physically meaningful surface characteristics in future quality assurance and part qualification processes.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

The demand for improving the nuclear waste management has since long been identified as one of the major hurdles for widespread use of nuclear energy. Nuclear waste management, through partitioning and transmutation (P&T) has been researched since the 1990ies with partitioning being a pre-requisite for the process. Recently, an innovative approach of reactors directly operating on spent nuclear fuel, iMAGINE, has been proposed which could deliver on the aims of P&T as a side effect to more efficient nuclear energy production in the future. The results shown here confirm that it is possible to achieve the aims of P&T without prior partitioning, but it is certainly less efficient since the high concentration of MAs, required for efficient burning, are impossible to obtain in a short operational time. The proposed nuclear waste management approach will be a long-term effort when it is accomplished without partitioning/separation technologies. However, none of the analyses contradicts this effort – the key points are a) when the technology for treating the waste is possible and reliable, the time horizon will not be a major concern b) the waste management is now intrinsically linked with energy production instead of requiring dedicated costly facilities, delivering a promising economic basis c) the waste management is now associated with long-term energy production and massively improved resource utilization. In summary, the objectives of P&T are achievable without prior partitioning – this is a ground-breaking result. However, the approach will require continued nuclear energy production for a very long time. In case of a nuclear phase-out decision, a much more efficient transmutation scenario would have to be envisaged as already discussed several years ago for Germany.

Smallholder dairying engages around 70 to 80 million rural households who are mostly landless, small and marginal farmers. These farmers face challenges in terms of adoption of balanced feeding practices including inclusion of compound feed in animal feeding. This necessitates to understand the socio-economic factors that are influencing the adoption of compound feed. The study found that 51% of dairying households adopted compound feed in animal feeding. The adopters and non-adopters of compound feed differed (P< 0.01) in terms of land holding, family educational status, breeds owned, membership status in farmer’s collectives, fodder adoption, area under fodder, access to grazing resources, availability of crop residues, milk production and milk marketing opportunities. Furthermore, users and non-users of compound feed had significant difference (P< 0.05) in extension agency contact, mass media contact, attitude towards dairying and gender participation in farming. The logit regression model explained the variance in adoption to 30%. Further it indicated the role of selective socio-economic characters, farming situations, feeding and marketing practices in adoption of compound feed. In specific membership in farmer’s collectives, marketing opportunity, milk production, farm men participation, family education status, grazing resources and attitude towards dairying has greatly influenced the adoption behaviour of compound feed in positive direction. Added, households with high experience, cultivating fodder and having access to crop residues tend to influence the adoption decision negatively. The research observed that farmers tend to use compound feed for increasing productivity in areas of better markets and there exists trade-offs between milk market opportunities, access to cheaper roughages and usage of compound feed.

This review examines additive manufacturing for refractory tungsten (W) and its alloys. It emphasizes the primary challenges and determining factors involved in additive manufacturing pure W, W alloys, and composites. Our focus in this regard extends to both process and alloying strategies designed to address critical issues such as densification, micro-cracking, and mechanical properties in tungsten-based components produced through additive techniques. Throughout the review, we organize existing knowledge and insights into convenient tables, serving as valuable resources for researchers embarking on a deeper exploration of these topics.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Additive manufactured interlocking structures often face challenges in achieving suitable joinability due to thermal deformation. This issue becomes particularly interesting when fabricating structures that require high density but not fully connected layers, such as soft-magnetic materials. This study focuses on systematical investigation of the deformation as a function of finger thickness and building direction in model interlocking structure. In the perpendicular direction to the build plate, the distortions of joint part were significantly reduced due to lower thermal stress. In addition, the effect of laser power and scan speed on interlocking structure are systematically discussed. Additionally, through stress and thermal simulations of additive manufacturing process, it was confirmed that the compensated model can enhance the joinability of interlocking structures. These findings contribute to the development of optimal design for additive manufactured parts of soft magnetic materials such as stators in electric motor components, which needs insulations and density.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Waste recovery is an important aspect towards human and environmental health protection. Unfortunately, proper food waste management is among the serious challenges in the field of solid waste management worldwide. Therefore, it is of great importance to conduct studies towards achieving efficient and cost-effective approaches for food waste management. This study investigated the potential of recovering food waste through maggots’ production as animal feed. The influence of fly attractant application on maggot production was also investigated. The study also investigated the potential of maggot production for waste recovery and reduction. Four different types of food waste (starch food leftovers, rotten bananas and peels, rotten pineapple and peels, and rotten oranges) were used in the investigation process. From the results, it was observed that the application of fly attractants had a significant effect on the production of maggots as determined by the weights after harvesting. Average weight of 94 g/kg of maggot was achieved from banana materials with an application of fly attractant during the 8th day of the cultivation; which is equivalent to a 32.4% increase from the same day when the material was cultured without applying fly attractant. Also, from the starch materials, about 77 g/kg of maggot weight was achieved; which is a 54.6% increase from the same day and the same material but without application of fly attractant. Moreover, the relative dry weight reduction in the trials varied from 52.5% to 82.4%.

Nowadays, probiotics has been proposed for substituting antibiotics in animal feed, since the European Union (EU) banned the latter compounds in 2006 to avoid their serious side effects on human health. Therefore, this work aimed to produce a probiotic product by fed-fermentation of whey with kefir grains for use in animal feed. The whey was fermented with a combination of kefir grains AGK1 and the free biomass present in whole milk fermented milk used to activate these kefir grains. The probiotic culture obtained was characterized with high levels of biomass, total viability and antibacterial activity. Some probiotic properties of the probiotic culture were investigated in vitro, including its survival at low pH values, under simulated gastrointestinal conditions, after freezing in skim milk at − 20 ºC, and in the commercial feed during storage at room temperature. The viable cells of lactic and acetic acid bacteria and yeasts exhibited higher tolerance to acidic pH and simulated gastrointestinal conditions when the cells were protected with skim milk and piglet feed, compared with washed cells. The results indicated the feasibility of producing a probiotic product at a low cost with a potential application in animal feed.

This paper analyzes the mitigation of enteric methane (CH4) emissions from ruminants with the use of feed additives inhibiting of rumen methanogenesis to limit global temperature increase to 1.5 °C. A mathematical simulation conducted herein predicted that pronounced inhibition of rumen methanogenesis with pure chemicals or bromoform-containing algae can contribute to limit global temperature increase by 2050 to 1.5 °C only if widely adopted at a global level and considering an efficacy higher than obtained in most studies. Currently, the most important limitations to the adoption of antimethanogenic feed additives are probably increased feeding cost without a consistent return in production efficiency, and achieving sustained delivery of inhibitors to the rumens of non-supplemented, extensively ranging animals. Economic incentives, and changes in rumen microbial metabolism caused by inhibiting methanogenesis, could potentially be used to make the methanogenesis inhibition intervention cost effective. Also, the composition of the methanogenic community, and rate of disappearance of inhibitors of methanogenesis in the rumen can influence the effective dose of the inhibitors, and hence the cost of their adoption. Possible means for sustained delivery of antimethanogenic compounds to extensively grazing animals are discussed. Limitations and knowledge gaps of these approaches, and future research directions, are examined.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

In order to solve the problem of fault diagnosis for CNC machine feed system under the condition of variable speed conditions, an intelligent fault diagnosis method based on multi-domain feature extraction and ensemble learning model is proposed. First, various monitoring signals including vibration signal, noise signal and current signal are collected. Then, the monitoring signals are preprocessed and the time-domain, frequency-domain and time-frequency domain feature indexes are extracted to construct a multi-dimensional mixed domain feature set. Finally, the feature set is putting into the constructed DoubleEnsemble-LightGBM model to realize the fault diagnosis of the feed system. The experimental results show that the model can achieve good diagnosis results under different working conditions for both the public data set and the feed system test bench data set, and the average overall accuracy is 91.07% and 98.06% respectively. Compared with XGBoost and other advanced ensemble learning models, the method has better accuracy. It provides technical support for the stable operation and intelligent of CNC machine tools..

Rapeseed meal (RM) is an important agroindustrial by-product produced in large quantities by oil extraction from seeds. However, the efficient utilization of RM as animal feed is limited by its low metabolizable energy, poor palatability, and high levels of fiber and anti-nutritional components. Here, we investigate the potential of enriching RM with single-cell protein by fermentation with conventional and unconventional yeasts, to make a nutritionally improved feed component. The process of simultaneous saccharification and fermentation improved the parameters of the waste biomass, especially the protein content, the amount of crude fiber, and the degree of biotransformation of isoflavone compounds present in the waste material. Fermentation yielded the highest protein gain for the Saccharomyces cerevisiae Ethanol Red strain (ΔN=2.38%) at a biomass load of 12.5 g and for Scheffersomyces stipitis (ΔN=2.34%) at an enzyme dose of 0.125ml/10g DM. Crude fiber content (CF) was reduced by 2.55–7.18%. The SSF process resulted in the conversion of isoflavones to forms with fewer adverse effects and lower estrogenic activity.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

Profiling technologies, such as proteomics, allow the simultaneous measurement and comparison of thousands of plant components without prior knowledge of their identity. The combination of these non-targeted methods facilitates a more comprehensive approach than targeted methods and thus provides additional opportunities to identify genotypic changes resulting from genetic modification, including new allergens or toxins. The purpose of this study was to investigate unintended changes in GM Bt maize grown in South Africa. In the present study, we used bi-dimensional gel electrophoresis based on fluorescence staining, coupled with mass spectrometry in order to compare the proteome of the field-grown transgenic hybrid (MON810) and its near-isogenic counterpart. Proteomic data showed that energy metabolism and redox homeostasis were unequally modulated in GM Bt and non-GM maize variety samples. In addition, a potential allergenic protein – pathogenesis related protein -1 has been identified in our sample set. These finding highlight the suitability of unbiased profiling approaches to complement current GMO risk assessment practices worldwide.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

Carotenoids are common and diverse organic compounds with various functional roles in ani-mals. Except for certain aphids, mites, and gall midges, all animals acquire necessary carotenoids only through their diet. The House fly (Musca domestica) is a cosmopolitan pest insect that populates diverse habitats. Its larvae feed on organic substrates that may vary in carotenoid composition according to their specific content. We hypothesized that the carotenoid composition in the adult House fly’s body would reflect its composition in the larval feed. We reared house fly larvae on substrates that differed in carotenoid composition and characterized the carotenoid composition of the emerging adults. Our results indicate that the carotenoid composition of adult House flies is related to the carotenoid composition in its natal substrate, but does not directly reflect it. We suggest that these findings may be developed to identify sources of House fly in-festations. We also recommend that care should be taken when considering the rearing substrates of House fly larvae used for animal feed.

The naphtha cracking process results in the production of ethylene, propylene, mixed C4, and pygas, which are all olefins. Distillation columns and cracking furnaces are the primary units of operation. The price of raw materials accounts for 80% of production costs. There is also the pos-sibility of using LPG, a less expensive raw material, in place of some of the naphtha. A change in the raw material will affect the operability of the distillation columns and influence the yield on the cracking side. To determine the best naphtha substitution for LPG without creating a hydraulic problem (Jet Flooding) in distillation columns, analysis utilizing simulation tools must be done. To simulate the substitution of naphtha for other feedstocks, a reliability model is being built by comparing simulation results with data from the actual plant. LPG flow is a free variable that is being used to substitute naphtha. The effects of economically advantageous naphtha substitution for LPG can be assessed with the use of simulation tools without impairing plant operability. Optimum naphtha substitution rate is 21.14% from base case which resulting jet flooding occurred at Propylene Fractionator No 2. By implementing this substitution case, benefit that can be driven $22,772.02/ hour.

Long non-coding RNA (lncRNA) can regulate several aspects of gene expression, being associated with complex phenotypes in humans and livestock species. In taurine beef cattle, recent evidence points to the involvement of lncRNA in feed efficiency (FE), a proxy for increased productivity and sustainability. Here, we hypothesized specific regulatory roles of lncRNA in FE of indicine cattle. Using RNA-Seq data from liver, muscle, hypothalamus, pituitary and adrenal gland from Nellore bulls with divergent FE, we submitted new transcripts to a series of filters to confidently predict lncRNA. Then, we identified lncRNA that were differentially expressed (DE) and/or key regulators of FE. Finally, we explored lncRNA genomic location and interactions with miRNA and mRNA to infer potential function. We were able to identify 126 relevant lncRNA for FE in Bos indicus, some with high homology to previously identified lncRNA in Bos taurus and some possible specific regulators of FE in indicine cattle. Moreover, lncRNA identified here were linked to previously described mechanisms related to FE in hypothalamus-pituitary-adrenal axis and are expected to help elucidate this complex phenotype. This study contributes to expanding the catalogue of lncRNA, particularly in indicine cattle, and identifies candidates for further studies in animal selection and management.

Automobile industry is recognized as one of the most influential sectors shaping the global economies, societies, and individual lifestyles. Therefore, fierce competitions among different companies are continuously undergoing, and innovations deserve special attention to improve the competitiveness. In the past several years, additive manufacturing (AM) is emerging as an innovative technology in the applications of automobile industry with significant advantages over traditional techniques. As a result, increasing attention has been attracted to combining AM technology with the development of automobile industry. Currently, many automobile players are optimizing their industrial layout by incorporating with innovative AM techniques, and meanwhile, many research progresses have been achieved to meet the market demand. This article aims at presenting a timely review to conclude the recent advances in the application of AM techniques in automobile industry, focusing on the available AM techniques, printable materials, and the industry applications. The future research opportunities and challenges are also outlooked. Hopefully, this work can be useful to the related researchers, as well as the game players in the industry of this field.

The paper presents the conceptualization and realization of a novel platform for additive manu-facturing, an industrial robot arm-based system for additive manufacturing applications. Tradi-tional 3D printers, especially those employing fused deposition modelling (FDM) processes, are restricted to depositing material in a single toolpath plane (e.g. x-y plane). The focus of this study was to explore the feasibility of integrating commercial off the shelf (COTS) additive manufac-turing technologies with a six degree of freedom industrial robot arm to yield a 3D additive manufacturing system with the capability to perform free-form six degree of freedom fused deposition modelling. The present paper presents the development of a platform from stage 0, i.e. materials to its use, and finally a printed product with the developed extruder.

The potential of the Additive Manufacturing technologies is impeded by the surface finish obtained on the as-manufactured material. Therefore, the influence of various surface treatments, commonly applied to space hardware, on the mechanical properties of three selected metallic alloys (SS316L, AlSi10Mg, Ti6Al4V) prepared by using Selective Laser Melting (SLM) and Electron Beam Melting (EBM) additive manufacturing processes have been investigated. Within this study, SLM using EOS M400 and EOS M280 equipment and in addition EBM using an ARCAM Q20 machine have been applied for sample manufacturing. A half-automated shot-peening process followed by a chemical and/or electrochemical polishing or Hirtisation® process has been applied in order to obtain lower surface roughness compared to their as-received states. Special emphasize has been taken on their tensile, fatigue, and fracture toughness properties. In addition, their stress corrosion cracking (SCC) behaviour including microstructural analysis using HR-SEM have been investigated.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

With the emergence of blockchain and smart contracts, traditional digital applications 1 such as identity management, supply chain management, banking and finance etc. are expected 2 to be transformed into Decentralized Applications (DApps). Blockchain interoperability is a new 3 and exciting aspect of blockchain technology that is quickly gaining popularity in many industries. 4 However, the widespread use of blockchains has not yet been achieved because DApps running on the 5 blockchain using smart contracts require access to authentic off-chain data. Users are more conscious 6 of their personal data privacy and consequently are more reluctant to share their data, posing a 7 challenge in the adoption of DApps. To solve this challenge, we present a novel quantum-resistant, 8 data authentication and zero-knowledge proof scheme named zk-DASTARK. Based on our proposed 9 scheme, we present a novel framework which can be used to feed authenticated off-chain data to 10 DApps without compromising user data privacy. Our proposed framework is quite efficient against 11 well-known off-chain data authentication frameworks. The proposed framework is implemented on 12 state-of-the-art quantum-resistant IOTA Blockchain and is highly efficient as it takes approximately 13 60 ms to generate a proof and approximately 10 ms to verify a proof.

Sustainability enhancement is one of the main challenges of aquaculture. Since feeds represent one of the major costs from an environmental point of view, it is priority to find sustainable alterna-tive ingredients for aquaculture diet. Insect meals have some advantages as ingredients for aqua-culture, like its sustainability and nutritional value. However, the biggest drawback of full-fat in-sect meal is its fatty acid profile. The objective of this work was to assess the effects of partial plant or marine-derived ingredients replacements with full-fat Tenebrio molitor meal (TM) at two differ-ent levels on growth performance and fatty acids profiles of Solea senegalensis. For this purpose, a control diet and four experimental diets were tested, two of them contained 5 and 10% w/w TM that replaced mostly fish meal. Two other experimental diets included 10 and 15% w/w TM that replaced mostly plant meals. The inclusion of insect meal resulted in an improvement in growth rate and feed efficiency in both cases. Moreover, dietary inclusion of insect meal increased muscle total protein and decreased total lipid, without changes in phospholipids, and maintaining the relative level of n-3 PUFA. In conclusion, our study demonstrated that full-fat TM inclusion up to 15% in S. senegalensis diets had no negative effects or even positive effects on fish survival, growth performance, nutrient utilization and flesh quality.

Marine sediment sample was collected and the total aerobic population was counted and probiotic Bacillus cereus was isolated. Then it was mixed with formulated feed by spraying, while control diet was purchased from a local aquarium. 30 days of feeding experiment was conducted. Carassius auratus fishes were randomly divided into two experimental groups in rectangular tanks. The first group served as a control in which fishes were fed with commercial feed. The second group of fish were fed with probiotic incorporated feed. After 40 days, their survival and growth performance were detected. Bacillus cereus incorporated feed significantly yielded higher survival rate of the fish compared to control. Food conversion ratio (FCR) was significantly lower than the control group. The main aim of this work is to investigate the effect of a marine probiotic bacteria, Bacillus cereus on the survival and growth performance of gold fish Carassius auratus.

To investigate the impacts of various sources of omega-3 on feed intake, digestibility, and blood metabolites in horses, this research was conducted. In this survey, 6 medium-sized Turkmen horses, aged 14 to 16 years, were used. The horses had no movement and health problems. This research was carried out in the form of a rotating design and included 3 periods, and each treatment had 2 repetitions in each period. In each experimental period, horses were randomly assigned to each of the 3 experimental treatments. The experimental treatments included C) Omega-3-free supplement (control treatment), R) Persialin flaxseed oil, and P) Persialin fat powder. At the beginning of each period, after the withdrawal period for the previous period, blood and feces samples were taken as the covariate factors, then the experimental treatments were consumed for 14 days, and after the adaptation to 100 grams of supplementing fat powder or flax seed oil, blood, and feces samples were taken at the end of the course. Fat supplements were added to the concentrate 1.5 hours before feeding the midday hay. The palatability was affected by the P treatment and was significantly lower than the R and C groups (P<0.05). But the difference between the two treatments (R and C) was insignificant in any of the periods. The digestibility of acid detergent insoluble fiber (ADF), crude protein (CP), ether extract (EE), and organic matter were not affected by any of the experimental treatments. Blood metabolites including glucose, cholesterol, triglyceride, total protein, and blood urea nitrogen were not influenced by experimental treatments. The serum albumin concentration of horses was affected by the R treatment in the first and third periods, but no significant difference was observed between the treatments in the second period.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

The paper describes problems with the current additive manufacturing chain before considering additive manufacturing as part of a modern manufacturing chain. Additive manufacturing can be used for near net-shape for finishing, for repair or for adding special features which cannot be made with traditional manufacturing. This paper describes how STEP-NC deals with these different scenarios in terms of accuracy, multi-material and variation of slice direction. The possibilities of multi-material objects also raises questions about the design of such objects and how these need to be handled by an advanced controller. The paper also describes non-planar slicing. Curved direction and cylindrical direction are shown to improve the accuracy of curved structure additive manufacturing. STEP-NC using boundary representation has better capability of depicting complex internal structures for additive processes. By using exact model of the final product represented by STEP-NC, the paper demonstrates improvements in data size reduction, slicing accuracy, and precise manipulation of internal structure.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

This study aims to get growth and feed efficiency of Nile tilapia (Oreochromis niloticus) with plant oils supplement from paring coconut (P.C.) and candlenut (C.N.) enrichment of Se in rations formula. The oil of P.C. was dominated by saturated fatty acid (SFA) lauric (42.67%), while the extract of C.N. was unsaturated fatty acids (UFA), linoleic (34.4%), and oleic (48.99%). The extract of P.C. and C.N. or mix oils added 4% in basal ration formula (28% crude protein (C.P.) with energy-protein ratio 8 kcal/kg). Completely Randomized Design (6 × 3) consists R1: basal ration; R2: basal formula with blend of paring coconut and candlenut oils (2% PC + 2% CN); R3: blend oils (R2) with trace additive Se; R4: 4% PC + Se; R5: 4% CN + Se; R6: control ration (32% CP). The result of production parameters showed that blend oils supplement enrichment Se 0.15 ppm in feed formula with ratio SFA: UFA = 1: 1 was the best growth rate equal with high protein feed. Feed efficiency ranged from 50.14-57.93% and protein efficiency ratio 1.72-2.06 both for CN oil (SFA: UFA = 1 : 2), paring coconut (SFA : UFA = 2 : 1) or blend oils (SFA : UFA = 1 : 1). Incorporation of blend oils with Se can be used for Nile tilapia fingerlings (≥ 10 g). Paring coconut oil was trend increasing on feed efficiency for tilapia bigger stadium (≥ 30 g).

The synergic features and enhancing strategies for various photopolymerization systems are reviewed by kinetic schemes and the associated measurements. The important topics include: (i) photo crosslinking of corneas for the treatmnet of corneal deseases using UVA-light (365 nm) light and riboflavin as the photosensitizer; (ii) synergic effects by a dual-function enhancer in a 3-initiator system; (iii) synergic effects by a 3-initiator C/B/A system, having an electron-transfer and oxygen-mediated energy-transfer pathways; (iv) copper-complex (G1) photoredox catalyst in G1/Iod/NVK systems for free radiical (FRP) and cationic photopolymeriation (CP); (v) radical-mediated thiol-ene (TE) photopolymerizations; (vi) superbase photogenerator based-catalyzed thiol−acrylate Michael (TM) addition reaction; and the combined system of TE and TM usinghual wavelength; (vii) dual-wavelength (UV and blue) controlled photopolymerization confinement (PC); (viii) dual-wavelength (UV and red) selectively controlled 3D printing; and (ix) 3-wavelength selectively controlled in 3D printing and additive manufacturing (AM). With minimum mathematics, we present ( for the first time), the synergic features and enhancing strategies for various systems of multi-commponents, initiators, monomers, and under one- two- and there-wavelength light. Therefore, this Review provides not only the bridging between modeling and measurements, but also guidances for further experimantal stuides and new applications in 3D printings and additive manufacturing (AM), based on the innovative concepts (kinetics/schemes).

Synthetic polymer-based gradient foams have considered as promising category of functionally graded materials with unique properties. In this study, the carbon dioxide (CO₂) foaming technology has used for PET-PEN (Polyethylene Terephthalate - Polyethylene Naphthalate) copolymer towards porous functional materials with thermal insulation with reasonable mechanical strength. Through scanning electron microscope based morphological characterization, a potential to fabricate gradient foam structures with micro-pores has identified. It has shown that variation of post-foaming temperature can tune the pore size distribution although the very high post-foaming temperature tends to cause structural instability. Thermal measurement data set the limits of operation, confirmed by simultaneous differential scanning calorimeter and thermo-gravimetric analysis. Mechanical stress and thermal conductivity also has measured to find rationale of thermal insulation with reasonable mechanical strength and to elucidate the actual 3D grid foam of copolymer.

Background: Drought, N deficiency and herbivory are considered the most important stressors caused by climate change in the agro- and eco-systems and varied in space and time shaping a highly dynamic and heterogeneous stressful environments. This study aims to evaluate the to-mato morpho-physiological and metabolic responses to combined abiotic and herbivory at dif-ferent within-plant spatial levels and temporal scales. Methods: Leaf-level morphological, gas exchange traits and VOC profiles were measured in to-mato plants exposed to N deficiency and drought, T. absoluta larvae and their combination. Ad-ditive, synergistic or antagonistic effects of the single stress when combined were also evaluat-ed. Morpho-physiological traits and VOC profile were also measured on leaves located at three different positions along the shoot axes. Results: The combination of the abiotic and biotic stress has been more harmful than single stress with antagonistic and synergistic but non-additive effects for the morpho-physiological and VOC tomato responses, respectively. Combined stress also determined a high within-plant phenotypic plasticity of the morpho-physiological responses. Conclusions: These results suggest that the combined stress in tomato determined a “new stress state” and a higher within-plant phenotypic plasticity which could permit an efficient use of the growth and defence resources in the heterogeneous and multiple stressful environmental condi-tions.

Food authorities aim to safeguard our food. This requires sensitive analyses to guarantee detection of both banned and regulated substances at low concentrations. At the same time, broad screening methods are needed to identify new emerging risks. For this purpose effect-based bioassays combined with mass spectrometric analyses offer an advantage. During the regular monitoring of dioxins in agricultural products, a discrepancy was observed between the results of the DR CALUX (Dioxin-Responsive Chemical Activated Luciferase gene Expression) bioassay and the confirmatory gas chromatographic high resolution mass spectrometric (GC-HRMS) analysis in egg and broiler fat samples. The response in the bioassay was high, suggesting a clear exceedance of the maximum limits of dioxins in these samples, yet regulated dioxins or dl-PCBs were not detected by GC/HRMS analysis . Ultimately, a broad screening analysis using GC-HRMS resulted in the identification of 2,3,7,8-tetrabromo-dibenzofuran (2,3,7,8-TBDF) in both egg and broiler fat. To investigate the potential; source of this brominated furan contaminant, different samples were analysed: bedding material, poultry feed, feed additives (choline chloride and L-lysine) and seaweed. The poultry feed and feed additives all contained 2,3,7,8-TBDF. Using a feed to food converter, it became clear that the poultry feed was probably the source of 2,3,7,8-TBDF in broilers and eggs through a feed additive like L-lysine or choline chloride. This study underlines the importance of using a combination of effect based screening assays with sensitive analytical methods to detect potential new and emerging risks.

In this study, four experimental treatments were evaluated: (T1) alfalfa hay + concentrate, (50:50%, DM); (T2) alfalfa hay + Leucaena leucocephala + concentrate, (30:20:50%, DM); (T3) alfalfa hay + prickly pear + concentrate, (30:20:50%, DM); and (T4) alfalfa hay + Leucaena leucocephala + prickly pear + concentrate, (30:10:10:50%, DM). NH3-N concentrations in T2 and T4 decreased when replaced alfalfa hay in 20 and 10 %, respectively. Treatments did not affect the concentration of total volatile fatty acids (TVFA) between T3 and T4 (p>0.05); while the concentrations among T1 and T2 were different (P<0.05). T2 showed a reduction of 25.5 % in the methane production when compared to T1(p < 0.05).The lowest concentrations of protozoa were observed in T2 and T4, which contained Leucaena leucocephala (T2) and Leucaena leucocephala + prickly pear (T4) (p<0.05). The highest concentration of total methanogens was recorded in T1 and were different to T2, T3 and T4 (p<0.05). Leucaena leucocephala at a inclusion percentage of 20 % decreased the methane when compared to T1; whereas prickly pear there was not a positive effect the methane production.

CGT is composed of fiber residues, leaves, dust particles, soil and others derived during the ginning and yarn spinning process at processing industries,. In the cotton spinning industrial clusters, farmers are using CGT) as one of the alternative roughage feed for their sheep, mainly during forage shortages in the summer months. To have baseline information on farmers using gin and factors driving them to choose CGT as a roughage source, which need to be identified for future planning on the usage of CGT in sheep feeding. Considering the above facts, the present study was undertaken to assess socio-personal characteristics, managemental practices associated with farmers using cotton gin in the feeding of sheep and also identify the factors driving the choice of the CGT as the primary source of roughage in the cotton spinning industry cluster of Tamil Nadu. For this, a survey among 80 sheep farmers was carried out using a pre-tested in-terview schedule. The collected data was analysed using descriptive statistics and logit regres-sion. The results indicated that the majority of male, aged, and large-land farmers were involved in practicing CGT feeding during the summer and also indicated the non-availability of green fodder during the summer season. The coarse type of CGT preferred more than the fine type of CGT trash in that area due to quality perception and price. The replacement level of CGT as roughage ranged from 33 to 75% of the total roughage requirement per day. About 88 percent-age of farmers were highly satisfied with the results of using CGT and they also expressed that the presence of foreign particles and dust were the major problems with using CGT. The choice of CGT as primary roughage among sheep farmers was primarily influenced by selective farming contexts, namely landholding, access to labour, and feeding practices of other livestock with cotton gin. Further, research has to be focused on to improve the quality of CGT in the future, as it is being utilised largely by sheep farmers.

ccurate recording of growth indicators for aquaculture species at different stages is essential for evaluating aquaculture production effectiveness and the rationality of feed formulations. Due to their convenience and non-invasiveness, weight, length, and condition factor are commonly used to assess the growth of aquaculture species . However, fish growth indicators, can vary significantly with age structure and feed components(nutrition), and relying on a single indicator may lead to misjudgments . In this study we investigated the growth indicators of gibel carp (Carassius auratus gibelio var. CAS V) at different growth stages (juvenile and adult) and different feed formulations. Meanwhile, fish weight-length relationship () was used to assess the growth indicators. The results showed that the weight-length relationship of gibel carp varied significantly with age and feed formulations. Additionally, the condition factor calculated depended on the weight-length relationship was more consistent with weight/length changes than measured. Weight analysis indicated that both weight, length, height, back thickness, and carcass ration had higher weights in analyzing fish growth. Therefore, during aquaculture production, fish growth evaluating requires considering diverse indicators such as weight, length,body height, back thickness, carcass ration,as well as condition factor to avoid misjudging the actual growth situation. Meanwhile, the use of the condition factor should consider the sufficient amount of data and whether the assumptions (such as being in a isometric growth period) are met.

CAD-CAE software companies have introduced numerous tools aimed at facilitating topology optimization through Finite Element Simulation, thereby enhancing accessibility for designers via user-friendly interfaces. However, the imposition of intricate constraint conditions or additional restrictions during calculations may introduce instability into the resultant outcomes. In this paper, an algorithm for updating the design variables called Adaptive Variable Design is proposed to keep the final design space volume of the optimized part always under the target value while giving the main algorithm multiple chances to update the optimization parameters and search for a valid design. This algorithm aims to producing results that are more conducive to manufacturability and potentially more straightforward in interpretation. A comparison between several commercial software and the proposed algorithm, implemented in MATLAB, is carried out to prove the robustness of the latter. By simulating identical parts under similar conditions, we seek to generate comparable results and underscore the advantages stemming from the adoption and comprehension of the proposed topology optimization methodology. Our findings reveal that the integrated enhancements within MATLAB pertaining to the topology optimization process yield favourable outcomes with respect to discretization, and the manufacturability of resultant geometries. Furthermore, we assert that the methodology evaluated within MATLAB holds promise for potential integration into commercial packages, thereby enhancing the efficiency of topology optimization processes.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.