This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

The information on the land use and soil conservation practice based on year 2006, 2010 and 2014, hence offering an opportunity to model the impacts of land use change on erosion, deposition and surface water runoff. Limitation in the use of hydrological models had been their inability to handle the large amount of input data that describe the heterogeneity of the natural system. In this study, a procedure that takes into account soil conservation practice based on the land use change, the response of soil erosion and sediment export from the George Town Conurbation catchment area, and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion areas of rural and urban planning proposes. Average annual sediment yield and data on a grid basis estimated using Universal Soil Loss Equation (USLE) and an emerging technology represented by Geographic Information System (GIS) used as a tool to produce a map for erosion rate. The changing of the land use from forest to agriculture and then to an urban area is a challenging task to research on land use demand for population, and environmental impact assessment is important for the planning of natural resources management, allowing research the modification of land use properly and implement more sustainable for long term management strategies. The challenge is to formulate strategies that would promote an integrated approach to the land use planning at an appropriate level as to address the issues that arose. Modelling for creating urban growth boundary for the George Town Conurbation must have to be controlled surface runoff and soil loss and sediment export from land use of the George Town Conurbation catchment.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.

A Robust Optimization framework with original concepts and fundamentals also admitting a fusion of ideals from relative regret models and static robust optimization, containing conservatism concepts is disclosed. The algorithm uses a fine-tune strategy to tune the model so the robustness and a target ideality can be mutually achieved with a specified risk. The framework comprises original concepts, a mathematical approach and an algorithm. The statistical treatment of the data with the original concepts from the framework make it able to make short, middle or long-term decision-making setting. The framework has high tractability since the algorithm forces the creation of a setting that makes a robust optimization with the specified risk. The framework can be applied in linear and nonlinear mathematical models since that the objective function is monotonic in the domain of the active convex region. Several examples are solved to best understand the framework and all results demonstrated high tractability and performance. There is a wide range of applications. Along all the text, there is a profound discussion about its philosophy, objective, original concepts, fields of application, statistical and probabilistic fundamentals.

It is currently difficult to obtain accurate fine dust information in residential areas due to the insufficient number of air quality monitoring systems and spatial imbalances. Therefore, a detailed particulate matter dispersion model including factors such as land use and meteorological information was developed in this study and used to create fine dust concentration distribution maps. The fine dust concentration distribution maps currently available to citizens were compared with those obtained by dispersion modeling, and population distribution data were employed to compare the populations exposed to fine dust according to the two methods. The results of the existing method and the developed particulate matter dispersion model differed significantly. For instance, the PM2.5 concentrations in Daejeon, South Korea, on February 17, 2018, were 56% “Good” and 44% “Moderate,” according to the existing method, while they were 31% “Good,” 26% “Moderate,” 28% “Unhealthy,” and 15% “Very Unhealthy,” according to the dispersion model. Furthermore, the existing method indicated that no portion of the population was exposed to poor fine dust concentrations, while the proposed model revealed that over 170 thousand people were exposed to such concentrations. These results on fine dust distributions will contribute to sustainable urban and environmental planning.

The digital era has significantly amplified the volume of online reviews, presenting both opportunities and challenges in harnessing insights from consumer feedback. Aspect-Based Sentiment Analysis (ABSA) has emerged as a crucial tool for distilling sentiments from these reviews, providing valuable data for enhancing product and service quality. This study introduces an advanced hybrid model, AdvSentiNet, which integrates adversarial training into the state-of-the-art framework to elevate the precision of sentiment detection at the aspect level. By employing an adversarial network, where a generative model competes against a classifier by crafting highly realistic synthetic samples, we aim to bolster the model's resilience against varied data samples. This innovative approach, unexplored in its entirety within the realm of ABSA, demonstrated remarkable performance improvements on benchmark datasets. For instance, accuracy on the SemEval 2015 dataset escalated from 81.7% to 82.5%, and for the SemEval 2016 dataset, it surged from 84.4% to 87.3%.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Anthropogenic activities such as the damming of rivers have resulted in the formation of depositional systems for sediments that are naturally transported along river channels all over the world. The steady accumulation of sediments has profound effects on how reservoirs function. As the reservoir ages, the impact of sedimentation becomes more pronounced. In an alluvial channel, the dynamics of sediment movement, scour, and deposition are exceedingly complicated. The quantitative and qualitative management of river engineering heavily relies on sediment motion. One of the key concerns affecting reservoir storage capacity is reservoir sedimentation. Understanding the form and behavior of the river or reservoir is necessary for a scientific approach to sedimentation. An overview of reservoir sedimentation processes, and models of reservoir and shallow water bodies is provided in this article. More research in the developing fields is advised for continuing studies on reservoir sedimentation due to climate change effects

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

The Casiquiare River is a natural channel that connects two of the greatest rivers in the world, the Orinoco and the Amazon in the South American Continent. The aim of this paper is to present a review and synthesis of the hydrological and sedimentological knowledge of the Casiquiare River, including the first hydro-sedimentary balance of the Casiquiare fluvial system conducted at the bifurcation and at the mouth on September 9-12, 2000, during the expedition ‘Humboldt-Amazonia 2000’. Bathymetric, flow discharge and physico-chemical measurements were made at the inlet and at the outlet of the Casiquiare Channel. The main conclusions of this study indicate that Casiquiare is taking a significant proportion of flow (20 to 30%) from the Upper Orinoco basin to the Amazon basin. Throughout its 356 km-course, this chameleon channel undergoes significant morphological, hydrological and bio-geochemical variations between the inlet and the outlet, whose most visible witnesses are the increase in its width (3 to 4 times), flow (7 to 9 times) and its change in water color (white to black water), under the influence of tributaries coming from vast forest plains.

Fine chemicals are produced in small annual volume batch processes (often &lt;10,000 tonnes per year), with a high associated price (usually &gt; $10/kg). As a result of their usage in the production of speciality chemicals, in areas including agrochemicals, fragrances and pharmaceuticals, their necessity will remain high for the foreseeable future. This review article assesses current methods used to produce fine chemicals with heterogeneous catalysts, including both well-established methods as well as newer experimental methods. A wide range of methods utilising microporous and mesoporous catalysts has been explored, including their preparation and modification before use in industry. Their potential drawbacks, as well as benefits, have been analysed, with their feasibility compared to newer, recently emerging catalysts. The field of heterogeneous catalysis for fine chemical production is a dynamic and ever-changing area of research. This deeper insight into catalytic behaviour and material properties will produce more efficient, selective, and sustainable processes in the fine chemical industry. The findings from this article will provide an excellent foundation for further exploration and a critical review in this field of fine chemical production using micro- and mesoporous heterogeneous catalysts.

Learning dental procedures is a complex task involving the development of fine motor skills. The reported use of theories and/ or evidence for designing learning activities to develop the fine motor skills needed for dental practice is limited. The aim of this review is to explore the available body of knowledge related to learning fine motor skills in dentistry. Evidence from studies investigating motor skill learning highlights the negative impact of self-focus and self-regulation on learning outcomes, particularly during the early stages of learning. The development of activities and schedules that enable novices to demonstrate characteristics similar to experts, without the reported long period of ‘deliberate practice’, is clearly of value. Outcomes of learning implicitly are important in dentistry because working under stressful conditions is common, either during undergraduate study or in practice. It is suggested that learning implicitly in the simulation stage can reduce disrupted performance when transitioning to clinical settings. Therefore, further investigation of effective methods for learning dental fine motor skills is indicated, using approaches that result in robust performance, even under stressful conditions.

This article uses a contemporary and revelatory case study to explore the relationship between three conversations in the innovation literature: design thinking, creativity in strategy and, the emerging area of art-thinking. Businesses are increasingly operating in a VUCA environment where they need to design better experiences for their customers and better outcomes for their firm and the Arts are no exception. Innovation, or more correctly growth through innovation, is a top priority for business and although there is no single, unifying blueprint for success at innovation, design thinking is the process that is receiving most attention and getting most traction. Design thinking teaches businesses to think with the creativity and intuition of a designer; to show a deep understanding of; and have empathy with the user. But design thinking has limitations. By placing the consumer at the very heart of the innovation process, design thinking can often lead to more incremental than radical ideas. Now there is a new perspective emerging, art-thinking, in which the objective is not to design a journey from current scenario; A to improved position: B. Art thinking requires the creation of B and spends more time in the open ended, problem space, staking out possibilities and looking for uncontested space. In Dublin, we examine a case of the oldest, largest and most prestigious fine art gallery and studio where most of the country’s best-known and successful visual artists both make, exhibit and sell their art. Graphic Studio Dublin is primarily a printmaking studio, established by artists over 60 years ago. It has facilities for woodblock, lino-print, silkscreen, intaglio and carborundum etching spread over four floors of a centrally located studio where the artists have access 24/7. But two years ago it found itself on the brink of collapse having borrowed heavily to invest in new facilities during the period of Ireland’s economic collapse. Its loans were sold to a vulture-fund who were about to foreclose in a move that would have seen a generation of Irish Artists displaced. A new board of directors was empaneled and they introduced some art thinking principles to bring the organisation back from the brink. They used an art-thinking mindset and design thinking tools to restore the fortunes of this venerable, artist-led institution and it worked.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

In this paper is discussed sediment transport as a mechanical process that characterises a natural stream or channel flow regime. The objective of experimental work presented in this paper is to recall and to give another prospect of well-known Meyer-Peter and Müller approach for estimation of Shield’s number (θ_c,θ) in laboratory conditions, and calibration of dimensionless MPM number (A). For this purpose two different experiments are conducted, during the first experiment water amount flushed on the flume and bed slope was changed simultaneously until equilibrium state is achieved, meanwhile is estimated the critical Shield’s number (θ_c). While, during the second experiment, water amount was kept constant, only bed slope of flume was continuously tilted, meanwhile sediment, discharge and Shield’s number (θ) was determined for given hydraulic conditions. In addition calibration of dimensionless MPM number (A) was performed, where several iteration were considered until for (A=3.42), sediment discharge measured become almost equal with sediment discharge computed by using MPM formula. After these experiments, is concluded that MPM formula can be used also for other certain initial condition and similar procedure may be adopted to calibrate the dimensionless MPM number (A) .

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

Spatiotemporal variations of sediments transported along rivers play a crucial role in a wide spectrum of uses, such as navigation, recreation, habitats or hydropower production. The advancement in technology has made it possible to use various indirect techniques to study and evaluate the transport of suspended sediment in fluvial environments. To investigate large-scale phenomena, remote sensing is becoming a largely utilized approach, as it allows to combine spatially-distributed and local information. Dam-induced sediment reduction occurs in large and small rivers worldwide, having profound implications on the fluvial systems. However, the systematic change of suspended sediment concentration (SSC) and its dynamic processes are not well known, and generally investigated only at the very local scale using field information. In this work, SSC maps were created by combining satellite images with local monitoring SSC data, using the Zhijiang -Chenglingji reach of the Changjiang River (China) as a case study, and analyzing how SSC dynamics changed over the period 2017-2022 in correspondence of extreme events. Multiple relationships between measured SSC and bands reflectance were tested, showing the potential of the best-performing one (R2=0.43) in mapping SSC spatiotemporal variations over an extent of dozens of kilometres, eventually providing new insights into the SSC dynamics at hotspots of the river systems, such as confluence zones, barriers, and reservoirs.

This paper presented a two-dimensional, well-balanced hydrodynamic and sediment transport model based on the solutions of variable density shallow water equations (VDSWEs) for sediment-laden flows, and the Exner equation for bed changes. Those equations are solved in a coupled way by the first-order Godunov-type finite volume method. The Harten-Lax-van Leer-Contact (HLLC) Riemann solver is extended to find the local Riemann fluxes in order to maintain the exact balance between the momentum term and the bed slope term. The advantage of a well-balanced scheme over an unbalanced scheme is demonstrated by the synthetic standing contact-discontinuity test case. Then, the model is employed to simulate two laboratory experiments. At last, a field case, the 1996 Lake Ha! Ha! flood event (Canada), is simulated. Results of cross sectional geometries and profiles of longitudinal thalweg agree well with measurements. The accuracy and simplicity of the numerical model, together with the robust implementation, make the model a good candidate for practical engineering applications.

This study presents results of the sediment yield Watershed of Ribeirão do Pinhal, in the city of Limeira, São Paulo, conducted under three different scenarios of the land use: 1 – land use in 2008, 2 – with reforested protection areas, 3 – the increase sugarcane's areas over grassland and citrus areas. The Soil and Water Assessment Tool (SWAT) was used as a hydro-sedimentological modeling tool to simulate these scenarios. This watershed was divided into five sub-watersheds according to the prevalent use, and adjustments were made in soils database parameters and cultures that are in SWAT, to adapt it to the Brazilian reality. Was used climatological data of eight years (2007-2014) for this modeling. Different sediment yield could be noted in the different types of land use, sub-watersheds and scenarios. The uses that presented higher sediment yield, in ascending order, were: natural vegetation, sugarcane, citrus, annual crop e grassland. Sub-watershed number 2 had the highest sediment yield (~10Mg.ha^-1), while the sub-watershed 5, the lowest (5.51Mg.ha^-1). This remained in the three scenarios. Overall, scenario 2 had the lowest sediment yield (7.74Mg.ha^-1). Scenario 1 had 8.37 Mg.ha^-1 and scenario 3, 8.58Mg.ha^-1. SWAT was considered efficient to simulate the sediment yield by scenarios and by use, combining different thematic and tabular data when performing the necessary adjustments on their original database.

Physical reason for the small scale tortuosity observed in sparks and lightning channels is unknown at present. In this paper it is suggested that the small scale tortuosity of the discharge channels is caused by the natural tendency for subsequent leader streamer bursts to avoid each other but at the same time to align as much as possible along the direction of the background electric field. This process will give rise to a discharge channel that re-orients in space during each streamer burst creating the small scale tortuosity.

The intrinsic non-linearity and complexity of suspended sediment dynamics, which are impacted by the geographical variability of basin parameters and temporal climatic patterns, make it difficult to estimate suspended sediment concentration (SSC) accurately in hydrological processes. Deep neural networks (DNNs), a cutting-edge modeling method that can capture the innate non-linearity in hydrological systems, have emerged as a solution to this problem. Using primary data on discharge, SSC, and turbidity, the long short-term memory method of DNNs was employed in this study to simulate the discharge-suspended sediment connection for the Esopus Creek, NY, USA as the first objective. To develop effective modeling strategies, multiple scenarios of feature selection, including combinations of discharge, turbidity and SSC for preceding days, were considered. Secondly, the variations in SSC and discharge between the three USGS gages along Esopus Creek that were upper stream, lower stream, and downstream, adjacent to the pourpoint were analyzed. Statistical metrics and scenarios of feature importance were used to evaluate the effectiveness of the DNN-based models. The study shows that among 24 DNN approaches feature selection is crucial in simulating the daily SSC, and discharge and presenting novel research directions for utilizing machine learning algorithms in water quality.

Soils provide important regulating ecosystem services and have crucial implications for human well-being and environmental conservation. However, soil degradation and particularly soil erosion jeopardize the maintenance and existence of these services. This study explores the spatio-temporal relationships of soil erosion to understand the distribution patterns of sediment retention services in mainland Portugal. Based on Corine Land Cover maps from 1990 to 2018, the InVEST Sediment Delivery Ratio (SDR) model was used to evaluate the influence of sediment dynamics for soil and water conservation. Spatial differences in the sediment retention levels were observed within the NUTS III boundaries, showing which areas are more vulnerable to soil erosion processes. Results indicated that the Region of Leiria, Douro and the coastal regions have decreased importantly sediment retention capacity over the years. However, in most of the territory (77.52%) changes in sediment retention were little or not important (i.e., less than 5%). The statistical validation of the model proved the consistency of the results, highlighting the usefulness of this methodology to analyse the state of soil erosion in the country. These findings can be relevant to support strategies for more efficient land use planning regarding soil erosion mitigation practices.

This study is part of a project designed to simulate the long-term landform equilibrium of a rehabilitated mine site. The project utilizes event fine suspended sediment (FSS) fluxes in a receiving stream following a rainfall event as an indicator of landform stability. The aim of this study was to use HEC-HMS to determine sediment and discharge quantity upstream to determine how it affects the downstream development of the catchment landform, in terms of sediment changes and geomorphology. Thus, the study focused on hydrology and sediment modelling of the upper catchment with HEC-HMS (Hydrologic Engineering Center-Hydrologic Modeling System) to determine daily discharge and sediment output at the catchment outlet. HEC-HMS was used to calibrate the stream discharge and FSS quantities at the catchment outlet to observed continuous discharge and FSS values. Calibration of the HEC-HMS model was done for two water years and then the same model parameters were used to validate the model for a third water year. Catchment discharge and FSS were calibrated and validated for continuous rainfall events against observed discharge and FSS data at the catchment outlet. The model was then run for a projected rainfall of 50 years. The denudation rate predicted by the model falls in the range previously determined for the region. The simulated sediment output was compared to the rainfall trends over the years. As a result, the sediment spikes following a rainfall-runoff event gradually decreased over time. Reducing FSS spikes indicate that the landform gradually attains stability. This modeling study can be used for long-term simulations to determine erosion equilibrium over the years and to quantify sediment yield in catchments for projected wet and dry rainfall scenarios.

The glioma-associated oncogene (GLI) family consists of GLI1, GLI2, and GLI3 in mammals, and is the effector in the Hedgehog signaling pathway. This family has important roles in the development and homeostasis of various tissues. To achieve these roles, the GLI family has widespread outputs. GLI activity is therefore strictly regulated at multiple levels, including via post-translational modifications for context-dependent GLI target gene expression. Conversely, dysregulated GLI activation has strong links with a variety of cancers. The protein arginine methyl transferase (PRMT) family is also associated with embryogenesis, homeostasis, and cancer via epigenetic modifications and signal transduction. In the PRMT family, PRMT1, PRMT5, and PRMT7 reportedly regulate GLI1 and GLI2 activity. PRMT1 methylates GLI1 to upregulate its activity and target gene expression. Cytoplasmic PRMT5 methylates GLI1 and is involved in GLI1 protein stabilization. In contrast, nucleic PRMT5 interacts with MENIN to suppress growth arrest-specific protein 1 expression, which assists Hedgehog ligand binding to Patched, indirectly resulting in downregulated GLI1 activity. PRMT7-mediated GLI2 methylation upregulates its activity through the dissociation of GLI2 and Suppressor of Fused. Therefore, PRMT1, PRMT5, and PRMT7 regulate GLI activity at multiple levels, and PRMT-mediated GLI dysregulation may be involved in cancer formation.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

Abstract:The objects of fine-grained image categories(e.g., bird species) are various subclass under different categories. Because the differences between subclass are very subtle and most of them are concentrated in multiple local areas, the task of fine-grained image recognition is very challenging. At the same time, some fine-grained networks tend to focus on a certain region when judging the target category, resulting in the lack of other auxiliary regional features. To this end, Inception V3 is used as the backbone network, and an enhanced and complementary fine-grained image classification network is designed. While adopting the method of reinforcement learning to obtain more detailed fine grain image features, the complementary network can obtain the complementary discriminant area of the target through the method of attention erasure to increase the network's perception of the overall target. Finally, experiments are conducted on CUB-200-2011, FGVC Aircraft and Stanford dogs three open datasets. The experimental results show that the proposed model has better performance.

Plants produce above- and below-ground biomass. However, our understanding of both production and decomposition of below-ground biomass is poor, largely because of the difficulties of accessing study materials. Below-ground organic matter decomposition studies are scanty and especially rare in the tropics. Here, we used a litter bag experiment to quantify the mass loss and nutrients dynamics of decomposing twigs and fine roots from an arbuscular mycorrhizal fungal associated tree, Parashorea chinensis, in a tropical rain forest in Southwest China. Overall, twig litter decomposed 1.9 times faster than fine roots (decay rate (k) twig=0.255, root=0.134). The difference in decomposition rates can be explained by a difference in phosphorus (P) concentration, availability and use by decomposers or C quality. Both materials showed an increase in N concentration, with final measurements still higher than initial levels. This suggests N may not be available due to microbial immobilization. Both carbon and nitrogen dynamics were significantly predicted by mass loss and showed a negative and positive relationship, respectively. Our study results imply that fine roots carbon and nitrogen contribute more to soils organic matter and enlarge the resident time. Therefore, better understanding of carbon cycle requires better understanding of mechanisms governing below ground biomass decomposition.

The objective of the research was to evaluate the concentration of organochlorine pesticides in sediment of the Alvarado Veracruz lagoon system, Mexico. To define the risk that causes to the public health the consumption of organisms that inhabit in sediments of this ecosystem. In 20 out of 41 stations analyzed, 11 prohibited organochlorine pesticides were identified, such as hexachlorocyclohexane, lindane, aldrin, dieldrin, endrin, among others. The highest concentrations were: aldrin 46.05; β-HCH 42.11; α-HCH 38.44; γ-HCH (lindane) 34.20; δ-HCH 31.61; methoxychlor 29.40; heptachlor epoxide 25.70; heptachlor 24.11; dieldrin 22.13; endrin 21.23; and endrin aldehyde 12.40 ng g-1. Concentrations reported are prohibited in international standards. In Mexico it is necessary to establish permissible limits in the environmental legislation for this matrix. There is a strong need to demonstrate, with scientific studies, the level of concentration reported by impact of compounds widely used in agricultural-livestock activities.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

The Rupat Strait, a part of the Malacca Strait, is recognized as semi-closed waters and shows a high activity; thus, discovering the transport sediment mechanism of the strait as a consequence of ambient and anthropogenic forces is essential. Hydrodynamic and sediment transport modelling was constructed using the 2-Dimensional Explicit method which is averaged over depth. The results show that the dispersion of sediment at high tide is longer than that at low tide. This follows the hydrodynamic model in which current velocity at high tide is greater than the ocean current at the low tide. The previous sediment observation supports the results of transport sediment modelling, indicating that the anthropogenic factors are highly associated with the sedimentation in the Rupat strait

Reservoirs are characterized by accumulation of sediments where micropollutants may concentrate, with potential toxic effects on downstream river ecosystems. However, sediment management such as flushing is needed to maintain storage capacity. Climate change is expected to increase sediment loads, but potential effects on their quality are scarcely known. In this context, sediment contamination by trace elements (As, Cd, Cr, Cu, Hg, Ni, Pb, Zn) and organics (PAHs, PCBs, C>12) was analyzed in 20 reservoirs located in Italian Central Alps. A strong As and a moderate Cd, Hg and Pb enrichment was emphasized by Igeo, with potential ecotoxicological risk according to PEC quotients. Siltation, granulometry, total organic carbon (TOC) and altitude resulted as the main drivers governing pollutant concentrations in sediments. According to climate change models, expected increase of rainfall erosivity will enhance soil erosion and consequently the sediment flow to reservoirs, potentially increasing coarse grain fractions and thus potentially diluting pollutants. Conversely, increased weathering may enhance metal fluxes to reservoirs. Increased vegetation cover will potentially result in higher TOC concentrations, which may contrast contaminant bioavailability and thus toxicity. Our results may provide elements for a proper management of contaminated sediments in a climate change scenario aiming at preserving water quality and ecosystem functioning.

Accurate and robust deep learning models for facial expression recognition are challenging to achieve, given the diversity of human faces and variations in images, including different facial poses and lighting conditions. In this work, we proposed a clock-driven convolutional Spiking Neural Network (SNN) and STDP fine-tune architecture, meticulously calibrated its hyperpa-rameters, and experimented with various optimization methods. The best model resulted was trained and evaluated on the Fer2013 and FER+ database, obtaining an accuracy of 61.87% and 79.97% without requiring auxiliary training data or face registration. To our best knowledge, the proposed SNN achieved comparable accuracy to CNNs of similar depth and possessed advantages of low energy consumption and high computational efficiency. The computational efficiency of the proposed SNN is approximately three times that of CNNs. Along with this, we introduced the very recent cumulative spike guided encoder visualization technique and revealed the strong encoding capability of the proposed SNN.

Radio bursts provide important diagnostics of energetic phenomena of the Sun. In particular, bursts in decimetric and metric wavelengths probe the physical conditions and the energy release processes in the low corona as well as their association with heliospheric phenomena. The advent of spectral radio data with high time and high frequency resolution has provided a wealth of information on phenomena of short duration and narrow bandwidth. Of particular value are spectral data combined with imaging observations at specific frequencies. In this work we briefly review the results of a series of observations comprised from high-sensitivity, low-noise dynamic spectra obtained with the acousto-optic analyzer (SAO) of the ARTEMIS-IV/JLS solar radiospectrograph, in conjunction with high time-resolution images from the Nançay Radioheliograph (NRH). Our studies include fine structures embedded in type IV burst continua (mostly narrow-band "spikes" and intermediate drift "fiber" bursts) and spike-like structures detected near the front of type-II bursts. The implications of the observational results to theoretical models are discussed.

This study is aimed to point out the possible application of the Enzyme-Linked ImmunoSorbent Assay (ELISA) test on table olives. Because olives, like many other foods, are not free from mycotoxin contamination, the main focus of this work was assessing the presence or absence of aflatoxins and ochratoxin A. The work was carried out in two phases. In the first phase, tests were carried out on commercial olives to assess the efficacy of the method and the kit (Veratox® 'Neogen' and AgraQuant® 'Romer Labs') by comparing them with the Liquid Chromatography coupled to a mass-mass spectrometer (LC-MS/MS); in order to understand if there were any interferences in antigen-antibody recognition; subsequently, mycotoxins were inoculated on the same samples with a known quantity, in order to assess the concentrations obtained and compare them to the expected ones. The second step involved modifying the method, so to improve the recovery of inoculated mycotoxins in the samples under study. Afterwards we evaluated the presence of mycotoxins in table olives supplied in the project. The results showed the effectiveness of the ELISA test, especially in the mycotoxin recovery phase. Indeed, after the modification of the mycotoxin extraction method, recoveries increased from 55% to over 70% for aflatoxins, and from 40% to over 55% for ochratoxin A. When analysing the samples provided by the above-mentioned company, the results showed some false positives, in particular in relation to ochratoxin A ’s analysis, mainly related to the first sample submission. Taking this into account, the ELISA test can be considered as an initial screening method applicable as a control programme for the evaluation of mycotoxins in olives which helps by saving time and costs. It should always be kept in mind that, if positive values should emerge, the LC-MS/MS analysis should be carried out.

The dynamics of suspended sediment involves inherent non-linearity and complexity as a result of the presence of both spatial variability of the basin characteristics and temporal climatic patterns. As a result of this complexity, the conventional sediment rating curve (SRC) and other empirical methods produce inaccurate predictions. Deep neural networks (DNNs) have emerged as one of the advanced modeling techniques capable of addressing inherent non-linearity in hydrological processes over the last few decades. DNN algorithms are used to perform predictive analysis and investigate the interdependencies among the most pivotal water quantity and quality parameters i.e., discharge, suspended sediment concentration (SSC), and turbidity. In this study, the Long short-term memory (LSTM) algorithm of DNNs is used to model the discharge-suspended sediment relationship for the Stony Clove Creek. The simulations were run using primary data on discharge, SSC and turbidity. For the development of the DNN models and examining the effects of input vectors, combinations of different input vectors (namely discharge, and SSC) for the current and previous days are considered. Furthermore, a suitable modelling approach with an appropriate model input structure is suggested based on model performance indices for the training and testing phases. The performance of developed models is assessed using statistical indices such as root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). Statistically, the performance of DNN-based models in simulating the daily SSC performed well with observed sediment concentration series data. The study demonstrates the suitability of the DNN approach for simulation and estimation of daily SSC, opening up new research avenues for applying hybrid soft computing models in hydrology.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

The impact of ponds on basins has recently started to receive its well–deserved scientific attention. In this study, pond–induced impacts on soil erosion and sediment transport were investigated at the scale of the French Claise basin. In order to determine erosion and sediment transport patterns under current conditions, the CORINE erosion and SWAT models were used. The impact of ponds on the studied processes was revealed by means of land cover change scenarios, using ponded versus pondless inputs. Results show that under current conditions (pond presence), 12.48% of the basin corresponds to no–erosion risk zones (attributed to the dense pond network), while 65.66% corresponds to low–erosion risk, 21.68% to moderate–erosion risk and only 0.18% to high–erosion risk zones. The SWAT model revealed that ponded sub–basins correspond to low sediment yields areas, in contrast to the pondless sub–basins, which yield appreciably higher erosion rates. Under the alternative scenario, erosion risks shifted to 1.12%, 0.52%, 76.8% and 21.56% for no, low, moderate and high–erosion risks, respectively, while the sediment transport pattern of the Claise completely shifted to higher sediment yield zones. This approach solidifies ponds as powerful man–induced modifications to hydro/sedimentary processes.

Lake Rawa Besar is an urban lake surrounded by dense settlements and market area. Currently Lake Rawa Besar is experiencing physical and ecology strain. This research’s objectives are to determine the levels of sediment and nutrient, the distribution, also the relation to land use and human activities producing pollutant. Field surveys with 30 sample points and observations was needed scattered within the lake. Measuring the value of each parameter is carried out in national standardized laboratory. The result shows that sediment load of TDS is still below the standard limit for clean water, while TSS levels in the middle of lake exceed the standard limit. Nutrient loads, spesifically nitrate and phospate levels is below the standard limit. While turbidity and BOD levels have a uniform distribution pattern in the lake, exceed the standard limit for clean water, and have a positive correlation. High levels of turbidity and BOD are caused by household waste and human activities producing organic waste such as tofu factory, fowl manure, and garbage dump. Small sewage goes into the lake mediates pollutants inflow. Attention is needed by nearby people, also for the government, to sustain the ecological condition of the lake.

Target recognition and fine-grained ship classification in remote sensing face the challenges of high inter-class similarity and sample scarcity. A transfer fusion-based ship image harmonization algorithm is proposed to overcome these challenges. This algorithm designs a feature transfer fusion strategy based on the combination of region aware instantiation and attention mechanism. Implement adversarial learning through image harmony generator and discriminator module to generate realistic remote sensing ship harmony images. Furthermore, the do-main encoder and domain discriminator modules are responsible for extracting feature representations of foreground and background, and further aligning ship foreground with remote sensing ocean background features through feature discrimination. Compared with other advanced image conversion techniques, our algorithm delivers more realistic visuals, improving classification accuracy for six ship types by 3% and twelve types by 2.94%, outperforming Sim2RealNet. Finally, a mixed dataset containing data augmentation and harmonizing samples and real data was proposed for the fine-grained classification task of remote sensing ships. Evaluation experiments were conducted on 8 typical fine-grained classification algorithms, and the accuracy of fine-grained classification for all categories of ships was analyzed. The experimental results show that the mixed dataset proposed in this paper effectively alleviates the long tail problem in real datasets, and the proposed remote sensing ship data augmentation framework performs better than state-of-the-art data augmentation methods in fine-grained ship classification tasks.

With the advancement of technology, signal modulation types are becoming increasingly diverse and complex. The phenomenon of signal time-frequency overlap during transmission poses significant challenges for the classification and recognition of mixed signals, including poor recognition capabilities and low generality. This paper presents a recognition model for fine-grained analysis of mixed signal characteristics, proposing a Geometry Coordinate attention mechanism and introducing a low-rank bilinear pooling module to more effectively extract signal features for classification. The model employs a residual neural network as its backbone architecture and utilizes the Geometry Coordinate attention mechanism for time-frequency weighted analysis based on information geometry theory. This analysis targets multiple-scale features within the architecture, producing time-frequency weighted features of the signal. These weighted features are further analyzed through a low-rank bilinear pooling module, combined with the backbone features, to achieve fine-grained feature fusion. This results in a fused feature vector for mixed signal classification. Experiments were conducted on a simulated dataset comprising 39,600 mixed signal time-frequency plots. The model was benchmarked against a baseline using a residual neural network. The experimental outcomes demonstrated an improvement of 9% in the exact match ratio and 5% in the Hamming score. These results indicate that the proposed model significantly enhances the recognition capability and generalizability of mixed signal classification.

Fine-tuning is an important technique in transfer learning that has achieved significant success in tasks that lack training data. However, as it is difficult to extract effective features for single-source domain fine-tuning when the data distribution difference between the source and the target domain is large, we propose a transfer learning framework based on multi-source domain called adaptive multi-source domain collaborative fine-tuning to address this issue. This approach utilizes multiple source domain models for collaborative fine-tuning, thereby improving the model's feature extraction capability in the target task. Specifically, this approach employs an adaptive multi-source domain layer selection strategy to customize appropriate layer fine-tuning schemes for the target task among multiple source domain models. The objective is to extract more efficient features. Furthermore, a novel multi-source domain collaborative loss function is designed to facilitate the precise extraction of target data features by each source domain model. Simultaneously, it works towards minimizing the output difference among various source domain models, thereby enhancing the adaptability of the source domain model to the target data. In order to validate the effectiveness of the proposed the adaptive multi-source domain collaborative fine-tuning framework, it is analyzed and compared with the most widely used fine-tuning methods by applying them to seven publicly available visual categorization datasets commonly employed in transfer learning. Experimental results demonstrate that, in comparison with the existing fine-tuning approaches, our method not only enhances the accuracy of feature extraction in the model but also provides precise layer fine-tuning schemes for the target task, resulting in state-of-the-art performance.

Fine-mesh exclusion netting is a potential alternative to organic and conventional insecticide application to control numerous pests of fruit crops. We tested whether fine-mesh exclusion netting would reduce pest abundance and increase marketable yield compared to organic spinosad insecticide sprays in an organically managed blackberry field. At the completion of flowering, we covered blackberry rows (N = 3) with fine-mesh exclusion netting (ProtekNet) and treated alternating rows (N = 3) with an organic spinosad insecticide (Entrust™). Fine-mesh exclusion reduced green June beetle (Cotinus nitida Linnaeus) and bird presence and marginally reduced Japanese beetle (Popillia japonica Newman) presence on blackberry canes compared to organic spinosad insecticide treatment. Exclusion netting reduced the capture of spotted-wing Drosophila (Drosophila suzukii Matsumara; SWD) in baited traps in the fourth week of exclusion, and reduced the overall number of SWD adults emerging from harvested blackberry fruits. Marketable yield in the fine-mesh exclusion treatments was two times higher than the organic spinosad insecticide treatment. These results suggest that fine-mesh exclusion netting is a functional pest control alternative to organic insecticide treatment.

The authors introduce the GRASS GIS add-on module g.citation as an initial implementation of a fine-grained software citation concept. The module extends the existing citation capabilities of GRASS GIS, which until now only provide for automated citation of the software project as a whole, authored by the GRASS Development Team, without reference to individual persons. The functionalities of the new module enable individual code citation for each of the over 500 implemented functionalities, including add-on modules. Three different classes of citation output are provided in a variety human- and machine-readable formats. The implications of this reference implementation of scientific software citation for both for the GRASS GIS project and the OSGeo foundation are outlined.

Fine dust causes various disorders, including cardiovascular, neurological, renal, reproductive, motor, systemic, respiratory, and cancerous diseases. Therefore, it is necessary to study functional materials to prevent these problems. In this study we used various methods, including quantitative PCR, flow cytometry, ELISA, and Alizarin O staining, to study the beneficial effects of erucic acid against fine dust. Erucic acid and erucic acid-induced exosomes (EIE) strongly suppress the attenuation of osteocytic differentiation and inflammation induced by fine dust. Erucic acid effectively suppresses inflammation in fibroblasts exposed to fine dust. Notably, despite exposure to fine dust, EIE promoted osteocytic differentiation in adipose-derived stem cells (ASC) and osteogenesis in macrophages, in addition to phagocytosis. Dramatic upregulation of RunX2 and BMP7 by EIE indicates that it is a strong activator of osteocytic differentiation in ASC and protects them from the effects of fine dust. Moreover, EIE induces immune activity and acts as an osteogenic trigger for macrophages. Therefore, this study suggests the potential use of erucic acid and erucic acid-induced exosomes (EIE) as biomaterials to prevent environment-borne diseases.

For the purpose of clean energy hydropower development, the construction of reservoirs has been continuously promoted in the Jinsha River basin for many years, and how the reservoirs affect the water and sediment process is a very necessary topic to study. This study is based on the gauged water and sediment data (span from the 1960’s to 2020) at Shigu, Panzhihua, and Xiangjiaba stations downstream located in the trunk channel of the river, and uses Mann-Kendall trend test method and double cumulative curve method to comprehensively judge the variation trends of runoff and suspended sediment load and reveal their credible mutation years. The linear regression method is used to reveal the variation characteristics of the relationship between water and sediment before and after the abrupt change years. The results show that the variations in runoff at Shigu and Panzhihua stations have significant and relatively obvious increasing trends, respectively, and that at Panzhihua station has a mutation year of 1985. The runoff at Xiangjiaba Station slightly increased but not significantly. The variation of suspended sediment load showed a temporal and spatial differentiation. The variation of sediment discharge at Shigu Station showed an increasing trend with a mutation year of 1997. For Panzhihua Station, it showed an increasing trend before 1998, but has significantly decreased since 1998. The fluctuation of sediment transport at Xiangjiaba Station was significant before 1998, but the trend is unclear. In the period of 1998−2020, it showed a significant decreasing trend, especially since 2013, when the mean annual suspended sediment load only accounted for 0.61% of its multi-year average. The variations of mean annual sediment concentration and sediment inflow coefficient at the hydrological stations is consistent with the variation trend of sediment transport. Before 2013, the correlation between water and sediment was strong, but thereafter it was extremely weak. The two sudden years of 1998 and 2013 are consistent with the year when large reservoirs were built in the river basin. The construction of large reservoirs and their large amount of sediment retention are the key reasons for the sudden changes in the water-sediment relationship and the sharp decrease in sediment transport in the downstream reach of the reservoir dam. The climate and underlying surface changes in the study area are not significant, and their impact on the water and sediment processes in the watershed is limited.

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

Understanding the complex relationship between sleep and memory is a major challenge in neuroscience. Many studies on memory consolidation in humans suggest that sleep triggers offline memory processes, resulting in less forgetting of declarative memory and performance stabilization in non-declarative memory. However, issues related to non-optimal experimental designs, task characteristics and measurements, and inappropriate data analysis practices can significantly affect the interpretation of the effect of sleep on memory. In this article, we discuss these issues and suggest constructive solutions to address them. We believe that implementing these solutions in future sleep and memory research will significantly advance this field by improving the understanding of the specific role of sleep in memory consolidation.

Improving the acquisition and retention of a new motor skill is of great importance. The present study (i) investigated the effects of difficulty manipulation strategies (gradual difficulty), combined with different modalities of feedback (FB) frequency on performance accuracy and consistency when learning a novel fine motor coordination task, and (ii) examined relationships between novel fine motor task performance and executive function (EF), working memory (WM), and perceived difficulty (PD). Thirty-six, right-handed, novice physical education students volunteered to participate in this study. Participants were divided into three progressive difficulty groups (PDG), 100% visual FB (FB1), 50% FB (FB2), and 33% FB (FB3). Progressive difficulty was increased by the manipulation of the distance to the target; 2 m, 2.37 m, and 3.56 m. Three FB modalities were investigated (i.e.: 100% visual FB (100% FB), 50% reduced feedback condition (50% RFB), and 33% reduced feedback conditions (33% RFB)). Performance assessments were conducted following familiarization, acquisition, and retention learning phases. Two stress-conditions of dart throws were investigated (i.e.: free condition (FC) and time pressure condition (TPC)). After the learning intervention, data showed that, under the free condition, the 100% FB group had a significant improvement in accuracy during all learning phases. Under time pressure condition, for the 50% RFB and the 33% RFB group, the measured variable (accuracy and consistency) showed a significant linear improvement in performance. The association between the percentage of RFB frequencies and the task difficulty (50% group) may be a more appropriate and manageable cognitive load compared to the 33% RFB and the 100% FB group. The present findings could have practical implications for practitioners because, while strategies are clearly necessary for improving learning, the efficacy of the process appears to be essentially based on the characteristics of the learners.

A probe of a patient, seeking help in an emergency ward of a French hospital in late December 2019 because of Influenza like symptoms, was retrospectively tested positive to COVID-19. Despite the early appearance of the virus in Europe, the prevalence and virulence appeared to be low for several weeks, before the spread and severity of symptoms increased exponentially, yet with marked spatial and temporal differences. Here, we compare the possible linkages between peaks of fine particulate matter (PM2.5) and the sudden, explosive increase of hospitalizations and mortality rates in the Swiss Canton of Ticino, and the Greater Paris and London regions. We also discuss the influence of Saharan dust intrusions on the COVID-19 outbreak observed in early 2020 on the Canary Islands. We find that high PM2.5 concentrations – possibly favored by air temperature inversions or Saharan dust intrusions – are not only modulating but even more so boosting severe outbreaks of COVID-19. We conclude that the overburdening of the health services and hospitals as well as the high over-mortality observed in various regions of Europe in spring 2020 can be linked to peaks of PM2.5 and likely particular weather situations that have favored the spread and enhanced the virulence of the virus. In the future, we recommend to monitor not only the prevalence of the virus, but also to consider the occurrence of weather situations that can lead to sudden, very explosive COVID-19 outbreaks.

Microplastics are a fast emerging group of contaminants. Their worldwide occurrence in water, sediment, and aquatic fauna raises questions and concerns as to their probable effects on aquatic life and ecology. This study investigates for the first time presence, abundance, and types of microplastics in water and sediment from a lagoon bordering the large urban agglomeration of Lagos in Nigeria, and renders additional information about grain size and sediment composition. Water and sediment samples were collected from four locations in the Lagos lagoon and a tributary. The abundance and distribution of microplastics in four range classes were determined for the sampled locations. Plastic particles were counted using digital microscopy, and identified with FTIR and pyrolysis GC-MS. The abundance of microplastics ranged from 310-2319 microplastic particles/kg in sediment, and 139-303 particles/m³ in water. The large discrepancy in the sediments can be explained by sediment characteristics as more microplastics were detected in the fine-grained sediments of Makoko. Fibres were the predominant shape found in all samples followed by fragments and few films whereas spheres were missing. Fibres were more abundant in water (92.6 %) than in sediments (32.5 %) while more fragments and foils occurred in sediments. The most commonly used polymers polypropylene and polyethylene were also the most detected ones in both matrices. Compared to other studies in Nigeria, our findings especially in the coarser sediments were lower while the fine-grained site revealed similar results.

Densimetric Froude (Fr) is the minimum velocity required to prevent sediment deposition in pipes. Prediction of Fr is of utmost importance in numerous applications in civil engineering. In this paper through using a new hybrid method. Genetic Algorithm (GA) is used for optimum selection of membership functions of Adaptive Neuro-Fuzzy Inference System (ANFIS), and Singular Value Decomposition (SVD) method is used to compute the linear parameters of ANFIS’s results section (ANFIS-GA/SVD). Also, two different target functions are known as training error (TE) and prediction error (PE) by Pareto curve, the trade-off between these functions is selected as the optimal modeling point. First, different models will be presented using the parameters affecting Fr prediction, classifying them in different groups; then the Fr parameter will be predicted for all the different models through utilizing three different sets of data and the ANFIS-GA/SVD technique. The results of the models indicate that the best Fr prediction is obtained when independent parameters such as volumetric sediment concentration (CV), ratio of median diameter of particle size to pipe diameter (d/D), ratio of median diameter of particle size to hydraulic radius (d/R) and overall friction factor of sediment (λs) use as input variables in prediction of Fr. A sensitivity analysis is also conducted for the purpose of examining the effect of each of the dimensionless parameters on Fr prediction accuracy. Comparing the results of the suggested models with the existing regression-based equations shows that ANFIS-GA/SVD (R²=0.986, MAPE=4.397, RMSE=0.206, SI=0.053, ρ=0.026, BIAS=-0.025) is more accurate than the rest of the models.

The identification and quantitative determination of wool and fine animal fibers are of great interest in the textile field because of significant price differences between them and common adulterations in raw and processed textiles. Since animal fibers have remarkable similarities in their chemical and physical characteristics, specific identification methods have been studied and proposed following advances in analytical technologies. The identification methods of wool and fine animal fibers are reviewed in this paper and the results of relevant studies are listed and summarized, starting from classical microscopy methods which are still used today not only in Small to Medium Enterprises but also in large industries, research studies and quality control laboratories. Particular attention has been paid to image analysis, Nir spectroscopy and proteomics which constitute the most promising technologies of quality control in the manufacturing and trading of luxury textiles and can find application in forensic science and archeology.

Oral immunization with the choleric toxin (CT) elicits a high level of protection against its enterotoxin activities and can control cholera in endemic settings. However, the complete B-cell epitope map of the CT responsible for protection remains to be clarified. Here, we have mapped the B-cell linear epitopes of the three chains of the CT protein (CTP) prepared by Spot synthesis. The immunoreactivity of sera from mice immunized with an oral, inactivated vaccine (Schankol†™) was measured against membrane-bound peptides for mapping. Results: Eighteen IgG epitopes were identified; eight in the CTA, three in the CTB, and seven in the protein P. Three epitopes, TQTGFVRHDDGYVST (aa 66-77, Vc/TxA-3), KNGAIFQVE VPGSQN (aa 64-78, Vc/TxB-11), and LNDEHK (aa 90-95, Vc/TxP-16), were chosen to synthesize a multiple antigen peptide that was used to coat ELISA plates to screen immunized mouse sera as a test for an in vitro diagnostics for cholera. Conclusion: Vaccination with inactive CT-generated antibodies against multiple linear epitopes and the selected epitopes can be used to construct immunological reagents for rapid serological diagnosis of cholera with high sensitivity and specificity.

We investigated preschool-aged children’s understanding of early fractional tasks and how that performance correlates with fine motor skills and use of gestures while counting. Participants were 33 preschoolers aged 4 to 5 in two Southeastern public elementary schools. Children were tested individually in an interview-like setting. Mathematics tasks were presented in a paper and pencil format and the Grooved Pegboard test assessed fine motor skills. Finally, utilization of gestures was evaluated by taking a behavioral rating of the child’s hand morphology, accuracy of gestures, and synchrony of gestures and spoken word while performing a counting task. Results indicate performance on fractional reasoning tasks significantly predicts both fine motor ability and accuracy of gestures.

The oral cavity is thought to be one of the portals for SARS-CoV-2 entry. Because there is limited evidence of active oral infection by SARS-CoV-2 viruses, we assessed the capacity of SARS-CoV-2 to infect and replicate in oral epithelial cells. Oral gingival epithelial cells (hTERT TIGKs), salivary gland epithelial cells (A-253), and oral buccal epithelial cells (TR146), which occupy different regions of the oral cavity, were challenged with replication competent SARS-CoV-2 viruses and with pseudo-typed viruses expressing SARS-CoV-2 spike proteins. All oral epithelial cells expressing undetectable or low levels of human angiotensin-converting enzyme 2 (hACE2) but high levels of the alternative receptor CD147 were susceptible to SARS-CoV-2 infection. Viral dynamics in hTERT TIGKs were different from those in A-253 and TR146 cells. For example, levels of viral transcripts were sustained in hTERT TIGKs but were significantly decreased in A-253 and TR146 cells at day 3 after infection. Analysis of oral epithelial cells infected by replication competent SARS-CoV-2 viruses expressing GFP showed that the signals of GFP and SARS-CoV-2 mRNAs were not evenly distributed. Taken together, our results demonstrated oral epithelial cells were susceptible to SARS-CoV-2 viruses despite of low or undetectable levels of hACE2, suggesting that alternative receptors contribute to SARS-CoV-2 infection and may be considered for development of future vaccines and therapeutics.

Flotation of small particles is one of the global challenges facing the mineral raw materials processing industry. Large amounts of non-ferrous and rare metals are lost in the flotation tailings in the form of mineral particles below 15 µm in size as a result of the low effectiveness of their capture by coarse bubbles generated in conventional flotation machines. The method of combined microflotation, which is being developed in recent years, uses not only coarse but also microbubbles (MB) produced in the stand-alone generator of air-in-water microdispersion, which serves as the flotation carriers. Depending on the dose of MB, the effect of their application may be both positive, but also negative. The theoretical analysis of various mechanisms of particle transfer onto the surface of coarse bubbles and further into the froth layer allowed to obtain the formula for the optimal MB dose f=2dddpρp, where dd is MB size; dp and ρp respectively are the size and the density of particles. Experiments performed on the copper ore flotation tailings at the Atalaya Mining (Spain) and Chaarat Kapan (Armenia) concentrators showed that, besides the optimal MB dose in the range of 1-3 ml/g, there is another optimal MB dose in the range of 10-20 ml/g, where the copper recovery increases by several percent compared to the reference test (f= 0). In the area between the optimal MB doses, the deep minimum in copper recovery is observed, which value is by several percent lower compared to the value in the reference test.

In this work, we adapt the fine-tuning algorithm of the Naïve Bayesian (FTNB) classifier to make it more suitable for imbalanced datasets. In particular, we boost misclassified instance probability terms by an amount that is disproportional to the harmonic mean of actual and predicted classes. The intuition is that discriminative attributes when the instance is misclassified would have small probability term pair values in both the actual class due to data scarcity and the predicted class due to weak correlation. Conversely, if both values are relatively high, then the attribute has good data coverage (support) and it should not be a cause for misclassification. Since the harmonic average is dominated by the smaller value and we have an imbalanced dataset, we should enact a large update if both or either term probabilities of actual and predicted classes are small. We used several benchmark datasets (60 different balanced and imbalanced datasets) to determine if the poor performance of the NB classifier is due to the scarcity of data and compared the performance of the proposed algorithm with NB, original FTNB, and other relatively new SOTA Ensemble Imbalanced Classifiers. Our empirical results reveal that the new proposed algorithm significantly outperforms all other classifiers.

Due to metal leaching and poor catalyst stability, the chemical industry’s fine chemical and pharmaceutical sectors have been historically reluctant to use supported transition metal catalysts to manufacture fine chemicals and active pharmaceutical ingredients. With the advent of new generation supported metal catalysts and flow chemistry, we argue in this study, this situation is poised to quickly change. Alongside heterogenized metal nanoparticles, both single-site molecular and single-atom catalyst will become ubiquitous. This study offers a critical outlook taking into account both technical and economic aspects.

Ensuring precise segmentation of colorectal polyps holds critical importance in the early diagnosis and treatment of colorectal cancer. Nevertheless, existing deep learning-based segmentation methods are fully-supervised, requiring extensive precise manual pixel-level annotation data, which leads to high annotation costs. Additionally, it remains challenging to train large-scale segmentation models when confronted with limited colonoscopy data. To address these issues, we introduce the general segmentation foundation model—Segment Anything Model (SAM) into the field of medical image segmentation. Fine-tuning the foundation model is an effective approach to tackle sample scarcity. However, current SAM fine-tuning techniques still rely on precise annotations. To overcome this limitation, we propose WSPoly-SAM, a novel weakly-supervised approach for colonoscopy polyp segmentation. WSPoly-SAM utilizes weak annotations to guide SAM in generating segmentation masks, which are then treated as pseudo-labels to guide the fine-tuning of SAM, thereby reducing the dependence on precise annotations data. To improve the reliability and accuracy of pseudo-labels, we have designed a series of enhancement strategies to improve the quality of pseudo-labels and mitigate the negative impact of low-quality pseudo-labels. Experimental results on five medical image datasets demonstrate that WSPoly-SAM outperforms current fully-supervised mainstream polyp segmentation networks on the Kvasir-SEG, ColonDB, CVC-300, and ETIS datasets. Furthermore, by using different amounts of training data in weakly-supervised and fully-supervised experiments, it is found that weakly-supervised fine-tuning can save 70% to 73% of annotation time costs compared to fully-supervised fine-tuning. This study provides a new perspective on the combination of weakly-supervised learning and SAM models, significantly reducing annotation time and offering insights for further development in the field of colonoscopy polyp segmentation.

Drought poses a significant constraint on rice production, and in this study, we have discovered a novel drought-sensitive mutant, designated as dsm3, arising from the progenies of indica rice variety Zhonghui8015 treated with EMS. Under drought stress conditions, dsm3 exhibited characteristic withered leaf tips, accompanied by increased levels of MDA and H2O2, reduced Pn, and decreased activity of POD and SOD. Genetic analysis revealed that the withered leaf tip phenotype was governed by a single recessive gene, designated as Osdsm3.To begin with, Osdsm3 was initially mapped to the short arm of chromosome 1 through a cross involving dsm3 and 02428. Subsequently, utilizing a population of 2591 F2 individuals, we narrowed down the location of Osdsm3 to a 78Kb interval, encompassing 13 open reading frames (ORFs). Sequencing analysis unveiled a mutation (1275G→A) in the exon of the candidate gene (LOC_Os01g10680), leading to premature translation termination. Moreover, a quantitative RT-PCR assay demonstrated high expression of OsDSM3 in the panicle and sheath, with a significant upregulation of drought stress-related genes under drought conditions. Phylogenetic analyses indicated that Osdsm3 shares evolutionary homology with UNE1, an intracellular transport protein found in Arabidopsis thaliana. Subcellular studies further confirmed that OsDSM3 resides in the cytoplasm. In conclusion, the forthcoming cloning of Osdsm3 holds promise for delving deeper into the molecular mechanisms governing rice drought resistance.

Heavy metal contamination is listed among the most alarming threats to the environment and human health. The detrimental effects of heavy metals in the natural environment span from a reduction of biodiversity to toxic effects on marine life - through microplastic born heavy metals -, to impairment of microbial activity in the soil, and to detrimental effects on animal reproduction. A host of different chemical and biological technologies have been proposed to alleviate environmental contamination by heavy metals. Relatively less attention has been paid to the microbial precipitation of heavy metals, as a side mechanism of the most general process of microbially induced calcite precipitation (MICP). This process is currently receiving a great deal of interest from both a theoretical and practical standpoint, because of its possible practical applications in concrete healing and soil consolidation, and its importance in the more general framework of microbial induced mineral precipitation. In this study, we analyse the ability of the marine bacteria Vibrio harveyi in co-precipitating CaCO3 minerals, together with Cd, Cr, Pb, and Zn added in form of nitrates, from solutions containing CaCl2. The precipitated carbonatic minerals were a function of the different heavy metals present in the solution. The process of co-precipitation appears to be rather effective and fast, as the concentrations of the 4 heavy metals were reduced in 2 days by 97.2%, on average, in the solutions.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

In the aftermath of pyroclastic-flow –dominated eruptions, lahars are the main geomorphic agent, but at the decadal scale, different sets of processes take place in the volcanic sediment cascade. At Unzen Volcano, in the Gokurakudani Gully we investigated the geomorphologic evolution and how the topographic change and the sediment change over time is controlling this transition. For this purpose, a combination of LiDAR data, aerial photography and photogrammetry, Ground Penetrating Radar and sediment grain-size analysis was done. The results show chocking zones and zones of enlargement of the gully, partly controlled by pre-eruption topography, but also by the overlapping patterns of the pyroclastic flow deposits of 1990 – 1995. The Ground Penetrating Radar revealed that on top of the typical lahar structure at the bottom of the gully, side-wall collapses were trapping finer sandy sediments formed in relatively low-energy deposition environment. This shows that secondary processes are taking place in the sediment transport process, on top of lahar activity, but also that these temporary dams may be a source of sudden sediment and water release, leading to lahars. Finally, the sediments from the gully walls are being preferentially oozed out of the pyroclastic-flow deposit, meaning that over longer period of time, there may be a lack of fines, increasing permeability and reducing internal pore-pressure needed for lahar triggering. It also poses the important question of how much of a past-event one can understand from outcrops in coarse heterometric material, as the deposit structure can remain, even after loosing part of its fine material.

Study of gross alpha (GA) and gross beta (GB) activity in road and surface deposited sediments were performed in various geographical areas in three Russian cities. To perform radiation measurements, new methods were applied which allow dealing with low mass and low volume dust size (2-100μm) samples obtained after the size fractionation procedure. The 2-10 μm fraction size has the highest gross beta activity concentration (GB)– 1.32Bq/g in Nizhny Novgorod (NN) and Rostov-On-Don (RND) while the 50-100 μm fraction size in Ekaterinburg. This is maybe associated with the subsistence of radionuclides that conveyed through natural processes and anthropogenic applications. The highest gross alpha activity concentration (GA) in fraction sizes was found in Rostov-on-Don city within the 50-100 μm– 0.22Bq/g. The fraction size 50-100 μmhas a higher gross alpha activity concentration than 2-10 and 10-50 μmfraction sizes due to natural partitioning of the main minerals constituting the urban surface deposited sediment (USDS). The geochemical processes that occur during the formation and transportation of USDS are reflected in the observed dependencies.Developed experimental methods of radiation measurements allowed to the extent the methodological base of urban geochemical studies.

The application of geophysical methods for the characterization of geomorphologic subsurface features has become very popular in recent years. Convential geophysical applications on undifferentiated and weathered slopes have been less effective. Multichannel analysis of surface waves (MASW) is a new hope for the solution of the problem. MASW methods was used to the first step in order to reconstruct the ancient eruption of Mount Samalas. MASW was applied to the remnants of ancient volcanic sediment on Lombok Island to determine the physical and physical characteristics of seismic subsurface features. This paper is also discussion the application's capabilities of the MASW method on undifferentiated and weathered volcanic deposits on the slope area and classified them. The results of the research show that MASW technique is powerful in characterizing and delineating the stratum of the layers of undifferentiated and weathered volcanic precipitation areas. MASW is able to predict subsurface structures, especially for shallow and thin layers and presenting site class information for internal structure (vertical resolution). Based on S wave velocity structure, undifferentiated and weathered volcanic layer, genes are classified into site class C, D, and E. In the future, this method will completed with combination of other geophysical method and parameters variation (frequency and spaces) for isopach mapping of volcanic sediment and then analysis of ancient volcanic eruption dynamics.

Endothall dipotassium salt and monoamine salt are herbicide formulations used for controlling submerged aquatic macrophytes and algae in aquatic ecosystems. Microbial activity is the primary degradation pathway for endothall. To better understand what influences endothall degradation, we conducted a mesocosm experiment to 1) evaluate the effects of different water and sediment sources on degradation, and 2) determine if degradation was faster in the presence of a microbial community previously exposed to endothall. Endothall residues were determined with LC-MS at intervals to 21 days after endothall application. Two endothall isomers were detected. Isomer-1 was abundant in both endothall formulations, while isomer-2 was only abundant in the monoamine endothall formulation and was more persistent. Degradation did not occur in the absence of sediment. In the presence of sediment degradation if isomer-1 began after a lag phase of 5-11 days and was almost complete by 14 days. Onset of degradation occurred 2-4 days sooner when the microbial population was previously exposed to endothall. We provide direct evidence that the presence and characteristics of sediment are of key importance in the degradation of endothall in an aquatic environment, and that monoamine endothall has two separate isomers that have different degradation characteristics.

This study is focused on the experimental investigation of compressive strength and durability properties of lightweight concrete mixtures with fine expanded glass and expanded clay aggregates using different microfillers. The paper proposes the relationships between the compressive strength and density of concrete mixtures with different proportions of lightweight aggregates mentioned above. The performed experimental studies have revealed the tendencies of possible usage of different amount of fine lightweight aggregates and their combinations in the production of concrete mixtures depending on the demands of practical application. Following the requirements for structural concrete subjected to environmental effects, durability properties (alkaline corrosion and freeze–thaw resistance) of the selected concrete mixtures with expanded glass aggregate were studied. The results of the experimental investigations have shown that durability of tested concrete specimens was sufficient. The study has concluded that the mixtures under consideration can be applied for the production of structural elements to which durability requirements are significant.

Boron carbide (B4C) powders with defined stoichiometry, high crystallinity, minimal impurity content, and a fine particle size are imperative for realizing the exceptional properties of this compound in advanced high-technology applications. Nevertheless, achieving the desired stoi-chiometry and particle size using traditional synthesis methods, which rely on prolonged, high-temperature processes, can be challenging. The primary objective of this study is to syn-thesize fine B4C powders characterized by high crystallinity and a sub-micron particle size, em-ploying a fast, and energy-efficient method. B4C powders are synthesized from elemental boron and carbon in a high-frequency induction heating furnace using the Electromagnetic Induction Synthesis (EMIS) method. The rapid heating rate achieved through contactless heating promotes the ignition and propagation of the exothermic chemical reaction between boron and carbon. Additionally, electromagnetic effects accelerate atomic diffusion, allowing the reaction to be completed in an exceptionally short timeframe. The grain size and crystallinity of B4C can be finely tuned by adjusting various process parameters, including the post-ignition holding temperature and the duration of heating. As a result, fine B4C powders can be synthesized in under 10 minutes. Moreover, these synthesized B4C powders exhibit high resistance to oxidation when exposed to air.

Aiming to reveal the kinetic characteristics of ceramic ball grinding of fine magnetite comprehensively, two types of ceramic balls ground with the same filling rate and total weight as steel balls were researched. The results show that the breakage rate of ceramic ball grinding is only half of that of steel ball grinding with the same media filling rate. With the same total media weight and the feed size less than 0.212 mm, the breakage rate of the ceramic ball grinding approaches the steel ball grinding and is 21.43% higher than that of the steel ball grinding. The main crushing form of magnetite changed from impact to abrasion in ceramic ball grinding compared with steel ball grinding, which significantly affected the value of the zero-order output constant a. Consequently, there is a noticeable difference in the variation of the parameter β related to the fines generation rate of the ceramic ball grinding compared with the steel ball grinding.

In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (Cc) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, Cc was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e0). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate Cc such as Oedometer test. This study presents a novel prediction model for Cc of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate Cc based on LL, PL, and e0. The performance of developed GEP-based model was evaluated through coefficient of determination (R2), root mean squared error (RMSE), and mean average error (MAE). High R2 and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R2, RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining Cc of fine-grained soils.

This paper investigates the impact of sediment deposition and inflow conditions on horizontal impact pressure and frequency analysis of bridge deck vibrations during flooding. Flooding-induced pressure and vibrations contribute to bridge collapse, and sediment deposition influences water flow and impact pressure. The study explores the relationship between sediment deposition height and impact pressure, revealing a significant increase as sediment approaches 50% of bridge deck clearance. Sediment amplifies impact pressure response to flow velocity changes. The dimensionless sediment deposition height has a greater influence on impact pressure compared to the inflow Froude number. Two distinct frequencies, dominant and secondary, are identified for impact pressure and water level fluctuations. Dominant frequencies positively correlate with sediment deposition height and Froude number, indicating an increasing trend. Secondary frequencies remain stable (0.31-0.58 Hz). These findings enhance understanding of flow dynamics and bridge-flow interaction in sediment-deposited channels, providing theoretical support for evaluating and managing disasters related to bridges in such environments. Overall, this research contributes to the field of bridge engineering and supports improved design and maintenance practices for bridges exposed to sediment-deposited channels.

The detection of antibiotic-resistant facultative pathogenic bacteria in surface waters is common in the present day. However, there is limited understanding of the factors that influence the spread and stabilization of resistance in this habitat, particularly regarding the role of biofilms. Despite the perceived differences between sediments, biofilms, and open water, their potential contribution to the long-term maintenance of resistances remains unclear. In this study, we investigated Escherichia coli isolates obtained from the Mur and Drava rivers in Austria. Samples were collected from both the water column and sediment at two locations per river: upstream and downstream of an urban area, including a sewage treatment plant. The iso-lates were subjected to antimicrobial susceptibility testing against 21 antibiotics belonging to seven distinct classes. Additionally, any isolates exhibiting an extended-spectrum beta-lactamase (ESBL) or carbapenemase phenotype were further analyzed for the presence of specific antimi-crobial resistance genes. E. coli isolates obtained from the two rivers exhibited resistance to at least one of the tested anti-biotics, with rates of 25.83% and 23.66% respectively. The most prevalent antimicrobial re-sistances observed were towards ampicillin, amoxicillin-clavulanic acid, tetracycline, and na-lidixic acid. Surprisingly, there was a similar proportion of resistant bacteria observed in both open water and sediment samples, contrary to expectations. The difference in resistance levels between samples collected upstream and downstream of the cities was minimal. Out of the total isolates, 13 E. coli were found to carry ESBL genes with one isolate carrying the gene for KPC-2 carbapenemase. There were no significant differences between the biofilm (sediment) and open water samples in the occurrence of antimicrobial resistance. Even the difference between the samples upstream and downstream of the cities and their wastewater treatment plants was minor. There seems to be no evidence of a large adaptive effect in this analysed biofilm population of E. coli. The un-typical phenotype of the KPC-producing and some of the ESBL-producing E. coli from this study could, however, be an indication that such adaptation effects generally exist in water.

A conventional 2D numerical model is improved by incorporating three submodels to consider different effects of secondary flow and a module for cohesive sediment transport. The model is applied to a meandering reach of Yangtze River to investigate secondary flow effects on cohesive sediment deposition, and a preferable submodel is selected based on the flow simulation results. Sediment simulation results indicate that the improved model predictions are in better agreement with the measurements in planar distribution of deposition as the increased sediment deposits caused by secondary current on the convex bank have been well predicted. Secondary flow effects on predicted amount of deposition become more obvious during the period when the sediment load is low and velocity redistribution induced by the bed topography is evident. Such effects vary with the settling velocity and critical shear stress for deposition of cohesive sediment. The bed topography effects can be reflected by the secondary flow submodels.

This paper is about to estimate the suspended sediment transport amount in the streams flowing into the Sapanca Lake Basin. There are 12 subsidiary streams flowing into the Sapanca Lake Basin. With the aim of estimating the suspended sediment transport in 2012-204 in these subsidiary streams, measurements belonging the parameters such as level, cross sectioning, flow rate, temperature and suspended sediment were made monthly. Along the measurement period, weather conditions were above seasonal normal and precipitations decreased. In order to estimate the suspended sediment amount by using results of the measurement obtained, Artificial Neuron Network (ANN), Sediment Rating Curve (SRC) and Multiple Linear Regression (MLR) models were used for different scenarios. It was seen that artificial neuron networks yielded the most accurate results among the models.

The inverse finite element method (iFEM) is a novel method for reconstructing the full-field displacement of structures by discrete measurement strain. In practical engineering applications, the accuracy of iFEM is reduced due to the positional offset of strain sensors during installation, and errors in structural installation. Therefore, coarse and fine two-stage calibration (CFTSC) method is proposed to enhance the accuracy of the reconstruction of structures. Firstly, the coarse calibration is based on a single-objective particle swarm optimization algorithm to optimize the displacement-strain transformation matrix related to the sensor position. Secondly, as selecting different training data can affect the training effect of self-constructed fuzzy networks, this paper proposes to screen the appropriate training data based on residual analysis. Finally, the experiments of the wing integrated antenna structure verify the efficient of the method on the reconstruction accuracy of the structural body displacement field.

The reflectance $R$ of monolayer graphene for the normal incidence of electromagnetic radiation is known to be remarkably defined only by $\pi$ and the fine-structure constant $\alpha$. It is shown in this paper that the reflectance (or the sum of transmittance and absorptance) of monolayer graphene, expressed as a quadratic equation with respect to the fine-structure constant $\alpha$ must unsurprisingly introduce the 2$^\text{nd}$ fine-structure constant $\alpha_2$, as the 2$^\text{nd}$ root of this equation, as well as two $\pi$-like constants for a convex and a saddle surface. It turns out that this 2$^\text{nd}$ fine-structure constant is negative, and the sum of its reciprocal with the reciprocal of the fine-structure constant $\alpha$ is independent of the reflectance value $R$ and remarkably equals $-\pi$. Particular algebraic definition of the fine-structure constant $\alpha^{-1} = 4\pi^3 + \pi^2 + \pi \approx 137.036$, containing the free $\pi$ term and agreeing with the physical definition of this dimensionless constant to the 5$^\text{th}$ significant digit, when introduced to this sum, yields $\alpha_2^{-1} = -4\pi^3 - \pi^2 - 2\pi \approx -140.178$. Assuming universal validity of the physical definition of $\alpha$, $\alpha_2$ defines the negative speed of light in vacuum $c_n$. The average of this speed $c_n$ and the speed of light in vacuum $c$ is in the range of the Fermi velocity ($10^6$ m/s). Furthermore, the 2$^\text{nd}$ negative fine-structure constant $\alpha_2$ alone introduces the imaginary set of base Planck units.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

The variation of river hydrologic process can not only reflect the impact of natural factors, but also the impact of human activities. The purpose of this study is to reveal the change trend of the hydrologic regime of the Yellow River and its response to ecological protection in the river basin. Based on the daily water and sediment observation data of representative gauging stations in the middle and lower reaches of the Yellow River, it was analyzed the variation trend of the annual and monthly runoff and suspended sediment load (SSL), and monthly mean runoff, suspended sediment transport rate (SSTR), sediment inflow coefficient, and hydrological regime in decadal average of the gauging stations during the period 1960-2019. The results show that the variation of annual runoff and SSL, as well as the monthly mean runoff and SSTR in decadal average, has a significant decreasing trend in the 1960’s-1990’s, which was mainly in response to the gradual implementation of ecological protection measures such as afforestation, grass planting, terrace construction, and check dam construction, etc. in the basin. In 2000’s and 2010’s, the annual runoff increased, while the SSL increased slightly. This was a response to the implementation of new river management measures such as ensuring the ecological water demand of the lower reaches and scouring the riverbed by manually regulated clear water discharged from the Xiaolangdi Reservoir. In the same time, the monthly mean runoff and SSTR for the flood season (Jun.-Oct.) decreased remarkably, while the process curve of the monthly mean discharge and sediment concentration, changed from a clockwise loop to a counterclockwise loop in the river reach below the Xiaolangdi dam. This was a comprehensive response to the environmental protection measures in the Yellow River basin, in which the construction and operation of the Xiaolangdi Reservoir played a key role. This study can provide reference for river basin management.

Although fine dust can cause various disorders, including cardiovascular, neurological, renal, reproductive, motor, systemic, respiratory, and cancerous diseases, there are not enough research for an oral disease. In this study we used various methods, including quantitative PCR, flow cytometry, immunocytochemistry, ELISA, and Alizarin O staining, to reveal the preventive effects of hemp-derived biomaterials in periodontal cells against fine dust. In this study, the two biomaterials (MSE; mature hemp stem extract and IE; induced exosomes derived from gingival cells exposed to MSE) revealed three main biological functions against fine dust. First, two materials suppressed the levels of inflammatory genes and activated anti-inflammatory genes in gingival cells. Second, these materials activated differentiation to osteoblast, periodontal ligament cells (PDLCs) and pulp progenitor cells (PPCs) from periodontal ligament stem cells (PDLSCs). Third, IE and MSE activated upregulation of LL-37 and down-regulation of MCP-1 in gingival cells and PDLSCs, respectively. Consequently, MSE and IE showed potential as a functional biomaterial in various fields, including pharmaceuticals, cosmetics, and foods.

In this study, the distribution patterns of southern horse mackerel are examined using commercial fine-scale resolution data. Using landings by size category and VMS data from the Portuguese commercial bottom trawl fishery, which consistently targets horse mackerel, this study provides a comprehensive analysis of horse mackerel age distributions spanning a decade (2010-2020). Importantly, the study addresses potential biases in commercial effort data and establishes the usefulness of commercial bottom-trawl gear as a suitable method for sampling and evaluate southern horse mackerel stock dynamics. Ordered regression models were applied to allow for the modelling of the distribution of multiple age categories and investigate spatio-temporal migrations off the Portuguese coast. Southern horse mackerel shows a widespread age distribution range and stable abundance with indications of seasonal and spatial patterns in the distribution of specific age groups. The insights derived from this research contribute valuable knowledge for understanding the dynamics and distribution patterns of fish populations.

Few-shot fine-grained image classification (FSFGIC) methods refer to machine learning methods which aim to classify images (e.g., bird species, flowers, and airplanes) belonging to subordinate object categories of the same entry-level category with only a few samples. It is worth to note that feature representation learning is used not only to represent training samples, but also to construct classifiers for performing various FSFGIC tasks. In this paper, starting from the definition of FSFGIC, a taxonomy of feature representation learning for FSFGIC is proposed. According to this taxonomy, we discuss key issues on FSFGIC (including data augmentation, local or/and global deep feature representation learning, class representation learning, and task specific feature representation learning). The existing popular datasets and evaluation standards are introduced. Furthermore, a novel classification performance evaluation mechanism is designed with a 0.95 confidence interval for judging whether the classification accuracy obtained by a certain specified method is good or bad. Moreover, current challenges and future trends of feature representation learning on FSFGIC are elaborated.

Alkali-silica reactivity (ASR) is one of multiple reactions responsible for premature loss in concrete infrastructure service life. ASR is a deleterious reaction initiated when highly reactive silicious content of aggregates reacts with alkali hydroxides content within portland cement in the presence of moisture. ASR results in the formation of expansive, white-colored gel-like material which results in internal stresses within hardened concrete. ASR induced stresses result in concrete cracking, spalling, and increased reinforcement steel corrosion rates. The main objective of this research is to improve the conditions of concrete infrastructure projects conditions by mitigating ASR damaging effect. The expansion of accelerated mortar bars poured using fine aggregates collected from different sources is measured versus time to evaluate aggregate’s reactivity. Different percentages of supplementary cementitious materials (SCMs) including class c fly ash, micro-silica, were used in remixing mortar bars to evaluate the efficiency of different types of SCMs in mitigating mortar bar expansion. Research findings showed that SCMs can mitigate ASR, thus, decrease the mortar bar expansion. The efficiency of SCMs in ASR mitigation is highly dependent on the incorporated SCM percentage and particle fineness. Silica fume, having the least particle size, displayed higher rates of ASR mitigation followed by fly ash, respectively. The outcomes of this research will assist design engineers in avoiding future losses due to ASR cracking in concrete infrastructure projects, and reduce the excessive need to maintenance, repair, and replacement activities.

To ensure the security of spatial-temporal Top-k query in two-tiered wireless sensor networks, many schemes have been proposed in the literature in the past decade. However, most of them only consider the scenario where sensor nodes are static, and cannot achieve the security goal for spatial-temporal Top-k query in mobile sensor networks, because the mobility of the sensor nodes will affect the spatial-temporal relationships of the sensory data items generated by the sensor nodes. Although we have proposed some schemes for two-tiered mobile wireless sensor networks (TMWSNs) in our previous work, there is still large room to improve their performances. In this paper, we proposed a novel scheme named STQ-TMWSN for secure fine-grained spatial-temporal Top-k query in TMWSNs based on the virtual-grid construction and the size-order encryption binding. Theoretic analysis shows that STQ-TMWSN can achieve low computation complexity and high security performance. Simulation results indicate that STQ-TMWSN brings much lower communication cost than the state-of-the-art schemes on securing Top-k query in TMWSNs.

Background: Iranian traditional medicine is a holistic school of medicine with a long prolific history. It describes numerous concepts and the relationships between them. However, no unified terminology has been proposed for the concepts of this medicine up to the present time. Considering the extensive use of concepts in the numerous textbooks written by the scholars over centuries, comprehending the totality of the terminology is obviously a very challenging task. To resolve this issue and overcome the obstacles, and code the concepts in a reusable manner, constructing an ontology of the concepts of Iranian traditional medicine seems a necessity.Methods: Makhzan al-Advieh, an encyclopedia of materia medica compiled by Mohammad Hossein Aghili Khorasani, was selected as the resource to create an ontology of Mizaj. The steps followed to accomplish this task included (1) compiling the list of classes for Mizaj; (2) arranging the classes in taxonomy; (3) determining object properties and their cardinalities; (4) specifying annotation properties including codes, labels, synonyms, and definitions for each concept; (5) reviewing the fields pertaining to Mizaj of all monographs in Makhzan al-Advieh. The ontology was created using Protégé with adherence to the principles of ontology development provided by the Open Biological and Biomedical Ontology (OBO) foundry. Results: Mizaj ontology was constructed with a final inclusion of 105 classes, three object properties, and 1078 axioms in the Iranian Traditional Medicine General Ontology database, IrGO, freely available at http://jafarilab.com/irgo/. An indented tree view and an interactive graph view using WebVOWL were used to visualize the ontology. All classes were linked to their instances in the UNaProd database to create a knowledge-base of Mizaj. Conclusion: We constructed an ontology-based knowledge base of ITM concepts of Mizaj in the domain of materia medica to help offer a shared and common understanding of this concept, enable reuse of the knowledge, and make the assumptions explicit. Extending IrGO will bridge the gap between traditional and conventional schools of medicine and help guide future research on new treatment options.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (C_c) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, C_c was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e₀). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate C_c such as oedometer test. This study presents a novel prediction model for C_c of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate C_c based on LL, PL, and e₀. The performance of developed GEP-based model was evaluated through coefficient of determination (R²), root mean squared error (RMSE), and mean average error (MAE). High R² and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R², RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining C_c of fine-grained soils.Keywords: evolutionary model, gene-expression programming (GEP), prediction, soil compression index, estimation, soil engineering, soil informatics, civil engineering, machine learning, data science, big data, soft computing, deep learning, forecasting, subject classification codes, construction informatics, computational intelligence (CI), artificial intelligence (AI), estimation

This retrospective study aimed to investigate the effect of known risk factors on nonsurgical periodontal treatment (NSPT) response using a pocket depth fine-tuning multilevel linear model (MLM). Thirty-seven patients (24 males and 13 females) with moderate to severe chronic periodontitis were treated with nonsurgical periodontal therapy. Follow-up visits at 3, 6, and 12 months included measurement of several clinical periodontal parameters. Data were extracted from a database system. Probing depth (PD) and Clinical Attachment Loss (CAL) reductions after NSPT in an overall of 1416 initially affected sites (baseline PD ≥ 4 mm), distributed on 536 teeth, were analyzed against known risk factors at three hierarchical levels (patient, tooth and site). The variance component models fitted to assess the three-level variance of PD and CAL decrease for each post-treatment follow-up showed that all levels contributed significantly to the overall variance (P < 0.001). Patients that underwent NSPT and were continually monitored had very curative results. All three hierarchical levels included risk factors who had impact on the to influence the magnitude of PD and CAL reduction. Specifically, the tooth’s type, surfaces involved and teeth mobility site-level risk factors showed the highest influence on these reductions, being highly relevant factors for the NSPT success.

The research was undertaken to study the way deformation behaves in ultrafine-grained (UFG) conducting Al-Zr alloys doped with Sc, Hf, and Yb. All in all, 8 alloys were studied with zirconium partially replaced by Sc, Hf, and/or Yb. Doping elements (X = Zr, Sc, Hf, Yb) in the alloys total 0.4 wt.%. The choice of doping elements is conditioned by possible precipitation of Al3X particles with L12 structure while annealing these alloys. Such particles provide higher thermal stability of a nonequilibrium UFG microstructure. Initial coarse-grained samples were obtained by induction casting. The UFG microstructure in the alloys was formed by Equal Channel Angular Pressing (ECAP) at 225°C. Superplasticity tests were carried out at temperatures ranging from 300 to 500 °C and strain rates varying between 3.310-4 and 3.310-1 s-1. The highest values of elongation to failure are observed in Sc-doped alloys. A UFG Al-0.2%Zr-0.1%Sc-0.1%Hf alloy has maximum ductility: at 450 °C and a strain rate of 3.310-3 s-1, relative elongation to failure reaches 765%. At the onset of superplasticity, stress–strain curves are characterized by a stage of homogeneous strain and a long stage of localized plastic flow. The dependence of homogeneous strain (eq) on test temperature in UFG Sc-doped alloys is increasing uniformly, which is not the case for other UFG alloys with eq(T) dependence peaking at 350-400 оС. Strain rate sensitivity coefficient of flow stress m is small and does not exceed 0.26-0.3 at 400-500 °C. In UFG alloys containing no scandium, m coefficient is observed to go down to 0.12-0.18 at 500 оС. It has been suggested that lower m values are driven by intensive grain growth and pore formation in large Al3X particles, which develop specifically at the ingot crystallization stage.

Background: Particulate matter and urban air pollution affect the human body and can lead to death. Epidemiological studies should consider the exposure to pollutants and the diverse responses of individuals depending on their sensitivity to the pollutants. Methods: In this study, air pollution measurements were obtained hourly at measuring stations operated by the national and local governments to increase the reliability of the measured values. A β-ray absorption method was used to analyze the measurements of fine dust and determine the particulate matter content. Results: The air pollution data were log-converted to enable the comparison of data from different time periods. The comparison was made, focusing on the period of Seoul's fine dust policy. As a result, the cancer incidence rate also decreased after the policy. The data on individual characteristics were obtained from a survey of Seoul citizens conducted from 2015 to 2016 and using indicators such as the quality of life and social trust of Seoul citizens. Concludions: The survey on the living environment and residence indicated that 80% of the heads of households were men. Women had a greater dissatisfaction than men with the residential, economic, and social environments. The survey questions on well-being were related to the internal and external environment such as air pollution, noise, and fine dust.

There must exist a reformulation of quantum field theory which does not refer to classical time. We propose a pre-quantum, pre-spacetime theory, which is a matrix-valued Lagrangian dynamics for gravity, Yang-Mills fields, and fermions. The definition of spin in this theory leads us to an eight dimensional octonionic space-time. The algebra of the octonions reveals the standard model; model parameters are determined by roots of the cubic characteristic equation of the exceptional Jordan algebra. We derive the asymptotic low energy value 1/137 of the fine structure constant, and predict the existence of universally interacting spin one Lorentz bosons, which replace the hypothesised graviton. Gravity is not to be quantized, but is an emergent four-dimensional classical phenomenon, precipitated by the spontaneous localisation of highly entangled fermions.