This study presents finite-time synchronization of chaotic fractional order systems with disturbance uncertainty and unknown time delay. First, a PID sliding surface is presented. Then, for the finite-time synchronization of the master and slave systems, a robust sliding-adaptive control method is provided. Update rules have been retrieved to estimate the system parameters by using the Lyapunov function while establishing the stability of the suggested mechanism and assuring the convergence of errors to zero. The proposed approach was used to solve the fractional order system of Gensou-Tsei with time-varying parameters, and the simulation results show that the presented approach performs well.

This paper studies the finite-time synchronization problem of fractional-order stochastic memristive bidirectional associative memory neural networks (MBAMNNs) with discontinuous jumps. A novel criterion for finite-time synchronization is obtained by utilizing the properties of quadratic fractional-order Gronwall inequality with time delay and the comparison principle. This criterion provides a new approach to analyze the finite-time synchronization problem of neural networks with stochasticity. Finally, numerical simulations are provided to demonstrate the effectiveness and superiority of the obtained results.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

In this research article we solve the problem of synchronization and anti-synchronization of chaotic systems described by discrete and time-delayed variable fractional order differential equations. To guarantee the synchronization and anti-synchronization of these systems, we use the well-known PID control theory and the Lyapunov-Krasovskii stability theory for discrete systems of variable fractional order.We illustrate the results obtained through simulation with examples, in which it can be seen that our results are satisfactory, thus achieving synchronization and anti-synchronization of chaotic systems of variable fractional order with discrete time delay.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

We employ another approach to quantize electromagnetic fields in the coordinate space, instead of the mode (or Fourier) space, such that local features of photons can be efficiently, physically, and more intuitively described. To do this, coordinate-ladder operators are defined from mode-ladder operators via the unitary transformation of systems involved in arbitrary inhomogeneous dielectric media. Then, one can expand electromagnetic field operators through the coordinate-ladder operators weighted by non-orthogonal and spatially-localized bases, which are propagators of initial quantum electromagnetic (complex-valued) field operators. Here, we call them QEM-CV-propagators. However, there are no general closed form solutions available for them. This inspires us to develop a quantum finite-difference time-domain (Q-FDTD) scheme to numerically time evolve QEM-CV-propagators. In order to check the validity of the proposed Q-FDTD scheme, we perform computer simulations to observe the Hong-Ou-Mandel effect resulting from the destructive interference of two photons in a 50/50 quantum beam splitter.

In this paper, a class of coupled competitive neural networks, which subject to disturbance and discontinuous activation functions, is concerned. To realize the fixed-time quasi-bipartite synchronization, an aperiodic intermittent controller is initially designed. Subsequently, by combining the fixed-time stability theory and nonsmooth analysis, several criteria are established to ensure the bipartite synchronization in fixed time. Moreover, synchronization error bounds and settling time estimates are provided. Finally, numerical simulations are presented to verify the main results.

This paper focuses on the problem of finite-time stabilization of homogeneous, non-Lipschitz systems with dilations. A key contribution of this paper is the design of a virtual recursive Hölder, non-Lipschitz state feedback which renders the non-Lipschitz systems in the special case dominated by a lower-triangular nonlinear system, finite-time stable. The proof is based on a recursive design algorithm developed recently, to construct the virtual Hölder continuous, finite-time stabilizer as well as a C¹ positive definite and proper Lyapunov function that guarantees finite-time stability of the non-Lipschitz non-linear systems.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

In this paper, to make the missile intercept the maneuvering target, the parallel approaching guidance law is developed. In order to estimate the target maneuver more accurately and reduce that’s influence on guidance accuracy, the distance-scalar disturbance observer is employed. Specifically, the estimation accuracy of the observer designed is regardless of the relative distance. The finite-time prescribed performance is employed to ensure that the line-of-sight angular rate is capable of converging to a predesigned small region in the specified finite time. All signals of interception system can guarantee ultimately uniformly boundedness proved by the Lyapunov stability theory. Finally, the availability of the parallel approaching guidance law is demonstrated by the numerical simulation.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

Digital twin, an innovative technology propelled by data and models, plays a seminal role in the digital transformation and intelligent upgrade of ships. This study introduces a digital twin methodology for real-time monitoring of ship structure deformation fields, based on finite discrete strain data, and a visualization tool framework is developed using virtual reality technology. First, the inverse Finite Element Method (iFEM) is employed to derive the deformation field of the ship structure in real time via sensor strain data. Secondly, the deformation field data obtained based on the iFEM algorithm is converted into general visualization data conducive to interpretation within VR applications. Lastly, a digital twin software tool is built to enable synchronous response and interaction between the virtual scene and the physical scene, directly superposing particular virtual objects (data acquired by sensors, CAD virtual models, and deformation field cloud images) onto the physical scene in real-time. The digital twin tool embodies a virtual reality visualization system framework integrating physical data measurement, reconstruction, analysis, expression, storage, rendering and interaction of deformation field data. Through practical application, the flexibility, effectiveness and compatibility of the developed prototype tool are verified. According to the results, the system can enhance the efficiency of scientific communication, model validation, and interdisciplinary sharing during the analysis and evaluation of mechanical properties of ship structures.

The synchronization of complex networks is believed to be closely related to network topology. How to study synchronization of real network without clear topology and parameters? In this Letter, a synchronized stability boundary equation is derived that is system- and disturbance-independent and applicable to arbitrarily coupled grids. The results imply that spontaneous synchronization in a network may be network independent. These conclusions provide new research paths for network synchronization and analyze the synchronization stability of grids in a unified way.

We explore several aspects of replica synchronization with the goas of retrieving the value of parameters for the Lorenz system. The idea is that of having a computer replica (slave) of a natural system (master, simulated in this paper), and exploit the fact that slave synchronizes with the master only if they evolve with the same parameters. As a byproduct, in the synchronized phase the state variables of the slave and that of the master are the same, thus allowing to perform measurements impossible on the real system. We review some aspects of master-slave synchronization using a subset of variables, with intermittent coupling. We show how synchronization can be achieved when some of the state variables are available for direct measurement using a simulated annealing approach, and also when they are accessible only through a scalar function, using a pruned-enriching ensemble approach, similar to genetic algorithms without cross-over.

This work investigates the sliding mode control (SMC) problem for a class of uncertain switched systems subject to asynchronous switching and an assigned finite time constraint. Two important issues are how to ensure the reachability of state trajectories within the assigned time and the input-to-output finite-time stability (IO-FTS) of the closed-loop switched systems during the whole phase under asynchronous switching. To achieve these objectives, an asynchronous sliding mode controller with adjustable parameters is constructed to drive the state trajectories onto the sliding surface during the assigned finite-time interval. By means of the partitioning strategy, sufficient conditions for the IO-FTS of the closed-loop switched are derived during the whole phase [0,T] using the multiple Lyapunov function (MLF) approach. Additionally, the asynchronous characteristics are detailedly investigated while analyzing the reachability of a specified sliding surface. Finally, an illustrative example is given to illustrate the effectiveness of the proposed method.

This paper proposed a time two-mesh (TT-M) finite difference numerical scheme to improve the efficiency of solving the symmetric regularized long wave (SRLW) equation. The TT-M Crank-Nicolson discretization and finite difference method are employed in time and space approximation respectively. The scheme involves three main steps: firstly, the time interval is divided into coarse and fine time meshes, then the nonlinear system is solved on the coarse time mesh; secondly, coarse numerical solutions on the fine time mesh are computed using an interpolation formula based on the solutions derived in the step one; lastly, the TT-M finite difference numerical solutions can be obtained through constructing the linearized fine time mesh system using Taylor’s formula. Compared to the currently existing TT-M numerical methods, the novelty of this study is that the nonlinear term including derivatives is linearized by Taylor’s formula for a function with three variables, whose error analysis is more complex. Finally, some numerical examples, including computational time and accuracy, preservation of conservation laws, are given to verify the efficiency of the scheme. By comparing it with the standard nonlinear finite difference scheme, this method can reduce CPU time without sacrificing accuracy.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

The synchronization of laser and X-ray sources is essential for time-resolved measurements in the study of ultrafast processes, including photo-induced piezo-effect, shock wave generation, and phase transition. On the one hand, the optical diagnostics (by synchronization of two laser sources) provides information about change in vibration frequencies, shock waves dynamics, linear and nonlinear refractive index behavior. On the other hand, the optical pump – X-ray probe diagnostics give opportunity to directly reveal the lattice dynamics. To integrate two approaches into a unified whole one need to create a robust method for synchronization of two systems with different repetition rate up to MHz range. In this paper, we propose a universal approach utilizing a field-programmable gate array (FPGA) to achieve precise synchronization between different MHz sources such as various lasers and synchrotron X-ray sources. This synchronization method offers numerous advantages, such as high flexibility, fast response, and low jitter. Experimental results demonstrate successful synchronization of two different MHz systems with a temporal resolution of 250 ps for these systems. This enables ultrafast measurements with sub-nanosecond resolution, facilitating the uncovering of complex dynamics in ultrafast processes.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

The Finite size Lyapunov exponent (FSLE) has been used extensively since the late 1990’s to diagnose turbulent regimes from Lagrangian experiments and to detect Lagrangian coherent structures in geophysical flows and two-dimensional turbulence. Historically, the FSLE was defined in terms of its computational method rather than via a mathematical formulation, and the behavior of the FSLE in the turbulent inertial ranges is based primarily on scaling arguments. Here we propose an exact definition of the FSLE based on conditional averaging of the finite amplitude growth rate (FAGR) of the particle pair separation. With this new definition, we show that the FSLE is a close proxy for the inverse structural time, a concept introduced a decade before the FSLE. The (in)dependence of the FSLE on initial conditions is also discussed, as well as the links between the FAGR and other relevant Lagrangian metrics, such as the finite time Lyapunov exponent and the second order velocity structure function.

This paper reports a new global Mittag-Leffler synchronization criterion with regard to fractional-order hyper-chaotic financial systems by designing the suitable impulsive control and the state feedback controller. The significance of this impulsive synchronization lies in the fact that the backward economic system can synchronize asymptotically with the advanced economic system under the effective impulse macroeconomic management means. Matlab LMI-toolbox is utilized to deduce the feasible solution in numerical example, which shows the effectiveness of the proposed methods. It is worth mentioning that the LMI-based criterion usually requires the activation function of the system to be Lipschitz, but the activation function in this paper is fixed and truly nonlinear, which cannot be assumed to be Lipschitz continuous. This is another mathematical difficulty overcome in this paper.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

Every finite simple group P can be generated by two of its elements. Pairs of generators forP are available in the Atlas of finite group representations as (not necessarily minimal) permutation representations P . It is unusual but significant to recognize that a P is a Grothendieck’s dessin d’enfant D and that a wealth of standard graphs and finite geometries G - such as near polygons and their generalizations - are stabilized by a D. In our paper, tripods P − D − G of rank larger than two,corresponding to simple groups, are organized into classes, e.g. symplectic, unitary, sporadic, etc (as in the Atlas). An exhaustive search and characterization of non-trivial point-line configurationsdefined from small index representations of simple groups is performed, with the goal to recognize their quantum physical significance. All the defined geometries G's have a contextuality parameterclose to its maximal value 1.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of analytes concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23-ga Car/PDMS assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 x 0.75 mm i.d. SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The developed model offers new insight into optimization of air and gas sampling using SPME.

Phase synchronization of weakly coupled limit cycle oscillators are related to the stability of the zero solution of the reduced-order dynamics of phase differences, represented by a systems of differential equations on a hypertorus. Using Rantzer's density function, a dual form of Lyapunov function, we propose a method to certify almost global stability of an equilibrium on a hypertorus. We show that the proposed method can certify robustness of phase synchronization of all-to-all and weakly coupled limit cycle oscillators with respect to disturbances in phases. The method leverages sum of squares polynomial optimization to construct the certification function.

In the paper, we develop some numerical schemes including finite difference scheme and finite volume scheme for the fractional Laplacian operator, and apply the resulted numerical schemes to solve some fractional diffusion equations. First, the fractional Laplacian operator can be characterized as the weak singular integral by a integral operator with zero boundary condition. Second, because of the solution of fractional diffusion equation is usually singular near the boundary, we apply finite difference scheme to discrete fractional Laplacian operator and fractional diffusion equation by fractional interpolation function. Moreover, it is find that the differential matrix of the above scheme is symmetric matrix, and strictly row-wise diagonally dominant in special fractional interpolation function. Third, we show finite volume scheme to discrete fractional diffusion equation by fractional interpolation function, and analyze the properties of differential matrix. Finally, the numerical experiments are given, and verify the correctness of theoretical results and the efficiency of the schemes.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

Quantum gravity theories rely on a minimal measurable length for their formulations, which clashes with the classical formulation of the uncertainty principle and with Lorentz invariance from general relativity. These incompatibilities led to the development of the generalized uncertainty principle (GUP) from string theories and its various modifications. GUP and covariant formulations of the uncertainty principle are discussed, together with implications for space-time quantization.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

Abscisic acid (ABA) plays a major role in promoting ripening in sweet cherry, a non-climateric fruit. Exogenous application of ABA has been performed to study fruit ripening and cracking, but this growth regulator is not used for commercial production. To determine the potential of this growth regulator to improve sweet cherry fruit quality, ABA canopy spraying was assayed in four cultivars. Canopy spraying of S-ABA significantly: 1) enhanced sweet cherry fruit color in ‘Glenred’, ‘Lapins’ and 'Bing' cultivars, but not in ‘Royal Rainier’ (a bi-colored cultivar), and 2) decreased fruit size and firmness in ‘Lapins’, ‘Bing’ and ‘Royal Rainier’. Seasonally reproducible effects were seen in ‘Lapins’ (mid/late-maturing) but not in ‘Glenred’ (early-maturing). Canopy spraying of nordihydroguaiaretic acid (NDGA) decreased color and increased fruit size in ‘Lapins’, but not in ‘Glenred’. Direct application of ABA on fruits attached to the tree, without application to the foliage, increased Lapins' fruit color without reducing size. These results suggest a localized fruit response to exogenous ABA application on fruit color development, but that a decrease in fruit size may be due to the effects of exogenous ABA on the tree canopy foliage.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

We introduce tools to capture the dynamics of three different pathways, in which the synchronization of human decision making could lead to turbulent periods and contagion phenomena in financial markets. The first pathway is caused when stock market indices, seen as a set of coupled integrate-and-fire oscillators, synchronize in frequency. The integrate-and-fire dynamics happens due to "change blindness", a trait in human decision making where people have the tendency to ignore small changes, but take action when a large change happens. The second pathway happens due to feedback mechanisms between market performance and the use of certain (decoupled) trading strategies. The third pathway occurs through the effects of communication and its impact on human decision making. A model is introduced in which financial market performance has an impact on decision making through communication between people. Conversely, the sentiment created via communication has an impact on financial market performance.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

In real financial market, the delayed market feedback and the delayed effect of government macro-control are inevitable. And both the delay of market feedback and the delay of macro-control effect bring about the mathematical difficulties in studying stabilization and synchronization of the hyper-chaotic financial system. However, employing Lyapunov function method, differential mean value theorem, suitable bounded hypotheses and pulse control technology results in the globally asymptotical stabilization and synchronization criteria. It is the first paper to drive the stabilization and synchronization criteria under the assumptions of the double delays. Finally, numerical examples illuminate the effectiveness of the proposed methods.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

Acoustic energy mapping provides the functionality to obtain characteristics of acoustic sources, such as: presence, localization, type and trajectory of sound sources. Several beamforming-based techniques can be used for this purpose, however, they rely on the difference of arrival times of the signal at each capture node (or microphone), so it is of major importance to have synchronized multi-channel recordings. A Wireless Acoustic Sensor Network (WASN) can be very practical to install when used for mapping the acoustic energy of a given acoustic environment. However, they are known for having low synchronization between the recordings from each node. The objective of this paper is to characterize the impact of current popular synchronization methodologies as part of the WASN to capture reliable data to be used for acoustic energy mapping. The two evaluated synchronization protocols are: Network Time Protocol (NTP) y Precision Time Protocol (PTP). Additionally, three different audio capture methodologies were proposed for the WASN to capture the acoustic signal: two of them, recording the data locally and one sending the data through a local wireless network. As a real-life evaluation scenario, a WASN was built using nodes conformed by a Raspberry Pi 4B+ with a single MEMS microphone. Experimental results demonstrate that the most reliable methodology is using the PTP synchronization protocol and audio recording locally.

This paper applied the space-time generalized finite difference scheme for solving the nonlinear dispersive shallow water waves as the modified Camassa−Holm equation, modified Degasperis-Procesi equation, Fornberg-Whitham equation, and its modified form. The proposed meshless numerical scheme was composed of the space-time generalized finite difference method, the two-step Newton-Raphson method, and the time-marching method. The space-time approach can treat the temporal derivative as one of the spatial derivatives. This numerical technique enables all the partial derivatives in the governing equation can be discretized by a spatial discretization method, and the mixed derivative can efficiently deal with using the proposed meshless numerical scheme. The space-time generalized finite difference method is advanced from the Taylor series expansion and the moving-least square method. The numerical discretization process is only related to functional data and weighting coefficients on the central node and its nearby nodes. Thus, the matrix system composed of nonlinear algebraic equations will be a sparse matrix and can be efficiently solved by the two-step Newton-Raphson method. Furthermore, the time-marching method was utilized to proceed with the space-time domain along the time axis. In this paper, several numerical examples were tested to verify the capability of the proposed space-time generalized finite difference scheme.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

This study investigates the country level determinants of liquidity synchronization and degrees of liquidity synchronization during economic growth volatility. As a non-diversifiable risk factor, liquidity co-movement shock spreads market wide and thus disrupts the overall functioning of the financial market. Firms in Asian markets operate in legal and regulatory environments distinct from those of firms analyzed in the previous literature. Comprehensive analyses of liquidity synchronicity in emerging markets are limited. A major knowledge gap pertaining to Asian emerging markets serves as the primary motivation for this study. Seven Asian emerging economies are selected from the MSCI emerging market index: Bangladesh, China, India, Indo-nesia, Malaysia, Pakistan and the Philippines for analysis from 2010 to 2019. The empirical findings show high levels of liquidity synchronicity in weaker economic and financial environments with low GDP growth, high inflation and interest rates and underdeveloped financial systems taking the form of low levels of private credit. Liquidity synchronicity is also affected by poor investor protection, political instability, weak rule of law and government ineffectiveness. Moreover, levels of liquidity synchronicity are higher in period of economic growth volatility.

The brain rhythms are essential for information processing in neuronal networks. Oscillations recorded in different brain regions can be synchronized and have a constant phase difference, i.e. be coherent. Coherence between local field potential (LFP) signals from different regions in the brain may be correlated with the performance of cognitive tasks, from which it is concluded that these regions of the brain are involved in the task performance together. In this review, we discuss why coherence occurs and how it is coupled to the information transfer between different regions of the hippocampal formation. Coherence in theta and gamma frequency ranges is described since these rhythms are most pronounced during the hippocampus-dependent attention and memory. We review in vivo studies of interactions between different regions of the hippocampal formation in theta and gamma frequency bands. The kay provisions of the review: 1) coherence emerges from synchronous postsynaptic currents in principal neurons, occurring as a result of synchronization of neuronal spike activity; 2) synchronization of neuronal spike patterns in two regions of the hippocampal formation can be realised through induction or resonance; 3) coherence at a specific time point reflects the transfer of information between regions of the hippocampal formation, in particular, gamma coherence reflects the coupling of active neuronal ensembles. Overall, coherence is not an epiphenomenon, but an important physiological process that has certain generation mechanisms and performs important functions in information processing and transmission across the brain regions.

The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

The intensive development of nanodevices acting as two-state systems has motivated the search for nanoscale molecular structures whose long-term conformational dynamics are similar to the dynamics of bistable mechanical systems such as Euler arches and Duffing oscillators. Collective synchrony in bistable dynamics of molecular-sized systems has attracted immense attention as a potential pathway to amplify the output signals of molecular nanodevices. Recently, pyridin-furan oligomers of helical shape that are a few nanometers in size and exhibit bistable dynamics similar to a Duffing oscillator have been identified through molecular dynamics simulations. In this article, we present the case of dynamical synchronization of these bistable systems. We show that two pyridine-furan springs connected by a rigid oligomeric bridge spontaneously synchronize vibrations and stochastic resonance enhances the synchronization effect.

Phase synchronization is one of the key issues that must be addressed in the bistatic synthetic aperture radar (BiSAR) system. LuTan-1 is an innovative L-band spaceborne BiSAR mission of China. An advanced synchronization scheme is used in the LuTan-1 system. The synchronization pulses are exchanged immediately after the ending time of the radar echo receiving window and before the starting time of the next pulse repetition interval. Therefore, it can not interrupt the normal SAR data acquisition, further improving synchronization frequency and avoiding the data missing effect. In order to accurately monitor system malfunctions and compensate for the phase synchronization errors introduced by hardware system, an innovative internal calibration strategy is designed and employed in the LuTan-1 mission. The test data acquired from the ground validation system of LuTan-1 are used to demonstrate the feasibility of the proposed scheme. The results validate the effectiveness of the proposed scheme and prove the promise for its future application in LuTan-1.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

Euler sums are alternating (or level two) extension of multiple zeta values (MZVs). Kaneko and Tsumura initiated the study of multiple T-values (MTVs), another level two generalization, by restricting the summation indices in the definition of MZVs to a fixed parity pattern. In this paper, we shall study finite MTVs and their alternating versions which are level two and level four variations of finite MZVs, respectively. We conjecture that all finite MZVs are in the Q-span of finite MTVs which in turn apparently lie in the span of finite Euler sums, and the inclusions are both proper. We shall first provide some structural results for Euler sums of small weights, guided by the author's previous conjecture that the finite Euler sum space of weight w is isomorphic to a quotient Euler sum space of weight w. Then, by utilizing some well-known properties of the classical alternating MTVs, we shall derive a few important Q-linear relations among the finite alternating MTVs, including the reversal, linear shuffle and sum relations. We then compute the upper bound for the dimension of the Q-span of weight w finite (alternating) MTVs for w<9, both rigorously using the newly discovered relations and numerically aided by computers.

The two-parameter Wright special function is an interesting mathematical object that arises in the theory of the space and time-fractional diffusion equations. Moreover, many other special functions are particular instantiations of the Wright function. The article demonstrates finite representations of the Wright function in terms of sums of generalized hypergeometric functions, which in turn provide connections with the theory of the Gaussian, Airy, Bessel, and Error functions, etc. The main application of the presented results is envisioned in computer algebra for testing numerical algorithms for the evaluation of the Wright function.

We derive a concentration inequality for the uncertainty in the mean computed by stratified random sampling, and provide an online sampling method based on this inequality. Our concentration inequality is versatile and considers a range of factors including: the data ranges, weights, sizes of the strata, the number of samples taken, the estimated sample variances, and whether strata are sampled with or without replacement. Sequentially choosing samples to minimize this inequality leads to a online method for choosing samples from a stratified population. We evaluate and compare the effectiveness of our method against others for synthetic data sets, and also in approximating the Shapley value of cooperative games. Results show that our method is competitive with the performance of Neyman sampling with perfect variance information, even without having prior information on strata variances. We also provide a multidimensional extension of our inequality and discuss future applications.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.

Euler’s product formula over the primes and Euler’s zeta function equate to enshrine the Fundamental Theorem of Arithmetic that every integer > 1 is the product of a unique set of primes. The product formula has no zero, and with a domain ≤1 Euler’s zeta diverges. Dirichlet’s eta function η(s), negates alternate terms of zeta, permitting convergence when s∈C and Re(s) < 1, and its non-trivial zeros {ρ}, have a deep relationship with the distribution of the primes. The Riemann Hypothesis is that all the non-trivial zeros have Re(ρ) = 1/2. This work examines the symmetries in a partial Euler’s zeta series with a complex domain equating it to the difference between two finite vector series whose matched terms have mirror-image arguments, but whose magnitudes differ when Re(s) ≠ 1/2. Analytical continuation generates a modified eta series η_l(s), in which every l^th term is multiplied by (1-l). If the integer l is appropriately determined by the Im(s), similar paired finite vector series have a difference that closely follows η_l (s) and their terminal vectors intersect in a unique way permitting zeros only when Re(s) = 1/2. Furthermore, those vectors tracking the derivatives of the series, have a special relationship permitting zeros of the differential only when Re(s) > 1/2.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

In this work we study the intersection properties of a finite disk system in the euclidean space. We accomplish this by utilizing subsets of spheres with varying dimensions and analyze specific points within them, referred to as poles. Additionally, we introduce two applications: estimating the common scale factor for the radii that makes the re-scaled disks intersects in a single point, this is the \v{C}ech scale, and constructing the minimal Axis-Aligned Bounding Box (AABB) that encloses the intersection of all disks in the system.

Drawing inspiration from a recent construction of a polyhedral structure associated with an icosahedrally-symmetric map on the Riemann sphere, the article shows how to build such "dynamical polyhedra" for other icosahedral maps. First, icosahedral algebra is used to determine a special family of maps with 60 periodic critical points. The topological behavior of each map is worked out and results in a geometric algorithm that constructs a system of edges---the dynamical polyhedron---in natural correspondence to a map's topology. It turns out that the maps' descriptions fall into classes the presentation of which concludes the paper.

Besides the Lagrangian and the Eulerian descriptions, the motion of a body can also be expressed relative to the present configuration of the body, known as the relative motion description. It is interesting to consider such a relative motion description in general to formulate the basic system of field equations for solid bodies. In doing so, when the time increment from the present state is small enough, the nonlinear constitutive equations can be linearized relative to the present state so that the resulting system becomes linear. This will be done for thermoelastic materials with a brief comment on the exploitation of entropy principle in general. Relative Lagrangian formulation is based on the well-known ``small-on-large'' idea, and can be implemented for solving problems with large deformation in successive incremental manner. Some applications of such a formulation in numerical simulations are briefly reviewed.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p&lt;0.001), DAPT (p&lt;0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

The aim of this work is to broaden the theory of computation by making use of fuzzy sets and multisets, which are generalization of ordinary sets. We study fuzzy multiset finite automata (FMFA), which are characterized by the incorporation of vagueness when it comes to the choice of the next state and multiple occurrences of the same input symbol. The resulting automaton is a genaralization of both classical automata and fuzzy automata. We discuss the algebraic characteristics of FMFA sub-automata—separatedness, strongly connectedness, cyclic, directable, and triangular FMFA in terms of equivalence classes induced by an equivalence relation defined on state set of FMFA. Intrestingly, for a given FMFA, a new FMFA can be constructed that is a homomorphic image of the original FMFA. We define different posets structures that can be associated with a given FMFA and show that some of them are upper semilattices and discuss the inter-relationship of a given poset, a finite upper semilattice (FUSL), a FMFA and a posets/FUSL associated with a given FMFA. Finally, we introduce the concept of decomposition of a FMFA in two different ways and characterize the strongly connected, triangular and directable FMFA.

We give three new authentication schemes without secrecy. The first two on finite fields and Galois rings, using Gray map for this link. The third construction is given on Galois rings. The main achievement in this work is to obtain optimal impersonation and substitution probabilities in the schemes. Additionally, in the first and second scheme, we simplify the source space and bring a better relationship between the size of the message space and the key space than the given in [8]. Finally, we provide a third scheme on Galois rings, which generalizes the scheme over finite fields constructed in [9].

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

Nitrogen (N) and sulfur (S) are essential macro-elements crucial for the proper development, productivity, nutrient uptake, and the building blocks of protein biosynthesis. The plant's N-metabolism is also influenced by S, and its deficiency can lead to a decline in the consumption of N from fertilizers. The objective of this research was to assess the impacts Temporal N and S applications on the nutrient uptake, productivity, use efficiencies and micronutrients content status in soybean seeds. The field trial in randomized complete block design carried out, experiment comprised fourteen treatments with varying N and S quantities. N and S were applied through starter and temporal applications in different combinations. The findings indicated that temporal application of individually N and S fertilization as 25 kg ha-1 as starter and 25 kg ha-1 as temporal applications at R2 stage enhanced the highest nutrient uptake, seeds and stalks yields. The use efficiencies, as well as the Zinc (Zn) and iron (Fe) uptake by seeds, showed an increase with the temporal application of both nutrients compared to the control. Furthermore, soil Zn and Fe contents were also enhanced with the temporal applications of nitrogen and sulfur fertilization. As a result, it could be decided that the nitrogen and sulfur temporal applications not only enhanced nutrient uptake, productivity and use efficiencies but also improved the micronutrient uptake by soybean. Furthermore, this practice contributed to an improvement in soil Zn and Fe content.

Leishmaniasis is the third most common vector-borne disease and a very important protozoan infection. Cutaneous leishmaniasis is one of the most common types of leishmaniasis infectious diseases with up to 2 million occurrences of new cases each year worldwide. A dynamic transmission multivariate time series model was applied to the data to account for overdispersion and evaluate the effects of three environmental layers as well as seasonality in the data. Furthermore, ecological niche modeling was used to investigate the geographical suitable conditions for cutaneous leishmaniasis using temperature, precipitation and altitude as environmental layers, together with the leishmaniasis presence data. A retrospective analysis of the cutaneous leishmaniasis spatial data in Afghanistan between 2003 and 2009 indicates a steady increase from 2003 to 2007, a small decrease in 2008, then another increase in 2009. An upward trend and regularly repeating patterns of highs and lows was observed related to the months of the year which suggests seasonality effect in the data. Two peaks were observed in the disease occurrence-- January to March and September to December -- which coincide with the cold period. Ecological niche modelling indicates that precipitation has the greatest contribution to the potential distribution of leishmaniasis.

The integration of magnetic observatories of many countries into the Intermagnet network has provided researchers with new opportunities to investigate many geophysical processes. The joint processing of measurement evidence from magnetic observatories located in various geolocations makes it possible to better understand the dynamics of the interaction of solar plasma fluxes with the Earth's magnetosphere. For the correct interpretation of the dynamics of physical processes, the accuracy of the time reference of measurement results is of great importance. The measurement results of local observatories were transformed to a unified ecliptic coordinate system oriented towards the Sun in order to extract small variations in the magnetic field occurring before the magnetic storm commencement. Before transforming the coordinates, a constant component equal to the average daily value of the magnetic field components was removed from the results of minute-by-minute measurements. Owing to the averaging evidence from 84 magnetic observatories of the Intermagnet network, variations in the magnetic field of cosmic origin, preceding the magnetic storm commencement were detected. The correlation analysis of these variations recorded by different observatories revealed the presence of time shifts between the data series of different observatories. Only 62% of the observatories had a relative data shift within the range of ± 1 minute. Before the joint data processing in order to efficient use of data recorded with a time shift a method for correcting time shifts has proposed.

We addressed whether arbitrary top–down regulation based on self-referential thinking could be valid for sensorimotor synchronization. We hypothesized that the dorsal anterior cingulate cortex (dACC) could regulate sensorimotor synchronization in accordance with internal models generated by self-referential processing. To illustrate the validity of the hypothesis, we conducted a missing oddball task with musical students. Utilizing the event-related deep-brain activity (ER-DBA) method cooperatively with the event-related potential (ERP) method, we found that dACC activation promotes repetitive tapping supported by modal completion, whereas dACC deactivation promotes precise tapping under avoiding erroneous responses for the missing pulses. Endogenous ERP components including P150 as a marker of modal completion and N200 as a marker of response inhibition supported this claim. Furthermore, combining the ER-DBA and ERP results, it was suggested that the brain creates a coherent story to promote repetitive tapping by mediating sensory evidence via modal completion. The free energy measurements theoretically support these findings, thereby confirming the validity of our hypothesis.

Direct reprogramming of fibroblasts into induced cardiomyocytes (iCMs) holds a great promise for regenerative medicine and has been studied in several major directions. However, cell-cycle regulation, a fundamental biological process, has not been investigated during iCM-reprogramming. Here, our time-lapse imaging on iCMs, reprogrammed by Gata4, Mef2c, and Tbx5 (GMT) monocistronic retroviruses, revealed that iCM-reprogramming was majorly initiated at late-G1- or S-phase and nearly half of GMT-reprogrammed iCMs divided soon after reprogramming. iCMs exited cell cycle along the process of reprogramming with decreased percentage of EdU⁺/αMHC-GFP⁺ cells. S-phase synchronization post-GMT-infection could enhance cell-cycle exit of reprogrammed iCMs and yield more GFP^high iCMs, which achieved an advanced reprogramming with more expression of cardiac genes than GFP^low cells; however, S-phase synchronization didn’t enhance the polycistronic-MGT reprogramming, in which cell-cycle exit had been accelerated. In conclusion, post-infection synchronization of S-phase facilitated the early progression of GMT-reprogramming through a mechanism of enhanced cell-cycle exit.

Enhancement in chemisorption is one of the active research areas in carbon materials. To remedy the thermally degraded chemisorption at high temperatures, we report a comprehensive study of kink structures in free-standing monoatomic carbon nanowires upon heating. Our Monte Carlo simulation considers multi-monoatomic carbon chains laterally interacted by the Van der Waals force. Our study reveals that the carbon nanowires maintain their linearity regardless of chain length at low temperatures, but this is not the case at high temperatures. Disordered kink structure is observed in the short carbon chains, especially above the Peierls transition temperature. The severe kink structure might increase the possibility of attaching negatively charged atoms, thereby contributing to the development of next-generation materials for chemisorption at high temperatures. We have also provided an important inspection that any physical property of the finite-length carbon chain predicted by ab-initio calculation should reconsider the atomic rearrangement due to the thermal instability at high temperatures.

The cosmological constant problem is examined by taking an Einstein--scalar with a Higgs-type potential and scrutinizing the infrared structure induced by finite temperature effects. A variant optimal perturbation theory is implemented in the recently proposed quantum-gravitational framework. The optimized renormalized mass, i.e., the renormalized mass determined by the variant optimal perturbation theory, of the scalar field turns out to be on the order of the temperature. This shifts the cosmological constant problem to compatibility of the consequent perturbative analysis. The compatibility is guaranteed essentially by renormalization group invariance of physical quantities. We point out the resummation behind the invariance.

In our publication from 8 years ago1 we calculated RKKY interaction between two magnetic impurities in graphene. The consideration was based on the perturbation theory for the thermodynamic potential in the imaginary time representation and direct evaluation of real space spin susceptibility. Only the case of zero temperature was considered. We show in this short notice that the approach can be easily generalized to the case of finite temperature.

In this paper, by extending some results of informational genomics, we present a new randomness test based on the empirical entropy of strings and some properties of repeatability and unrepeatability of substrings of certain lengths. We give the theoretical motivations of our method and some experimental results of its application to a wide class of strings: decimal representations of real numbers, roulette outcomes, logistic maps, linear congruential generators, quantum measurements, natural language texts, and genomes. It will be evident that the evaluation of randomness resulting from our tests does not distinguish among the different sources of randomness (natural, or pseudo-casual).

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Elbow dislocation and instability present significant clinical challenges, necessitating a thorough understanding of the underlying bio-mechanical mechanisms. In this study, a quasi-static three-dimensional finite element model of the human elbow joint is developed to investigate stress distribution and stages of dislocation in the human elbow under various loading conditions. The model simulates the elbow joint in different degrees of flexion (30°, 45°, 60°, and 90°) and forearm positions (pronation and supination), providing detailed insights into the progression of dislocation. Significant findings include the identification of high stress concentrations on the humerus at 90° flexion and on the radial and coronoid processes at 30°, 45°, and 60° flexion. Three reproducible stages of dislocation were observed, particularly in flexed positions with forearm pronation or supination. These stages align with experimental observations and highlight the initial occurrence of bony failures, such as radial head and ulnar coronoid fractures, preceding soft tissue tears. Clinically, the study underscores that early-stage low-impact posterior elbow dislocations retain enough stability to be managed with closed reduction and early mobilization. However, as dislocations progress, significant damage to the medial and lateral collateral ligaments is expected, necessitating more invasive treatments. This research provides valuable bio-mechanical insights into elbow dislocation, aiding in the development of improved treatment strategies and enhancing patient outcomes through precise and timely clinical interventions. The validated FEM serves as a powerful tool for pre-surgical planning offering a comprehensive understanding of elbow joint mechanics.

The Schwarzschild metric describes a non-rotating and charge-free celestial body, and it results in things stopping at the event horizon of a black hole and spending infinite time across the event horizon by the observer far away from the black hole. The analysis of the particle’s behavior at the event horizon tells us that this solution predicts an un-expanded black hole which violates the astronomical observations and our knowledge about the black hole. Although some alternative metrics have been proposed, the singularity problem is still unsolved. In this research, the degenerate Fermi electron gas is used to reveal that the Fermi electron gas cannot shrink to a point no matter how large energy it obtains, so the singularity exists at the center very unreasonably. In order to avoid these problems, a finite-size nucleus of the black hole is proposed and reasonably explained by the behaviors of the Fermi electron gas and the Fermi neutron gas there. On the other hand, the Kerr-Newman metric is the one describing the rotating and charged black hole and the equation of the light velocity at each space point can be obtained. It tells us that there are two real and non-imaginary solutions for the radial speed of light at the position larger than the Schwarzschild radius.

This paper studies the duration patterns of unemployment spells for immigrants and the determinants of unemployment’s completion into one of a number of studied labour market states in Finland. We estimate a duration model for unemployment with competing risks of its terminating into employment, labour market training or economic inactivity. Taking into account the wide period of observation and opportunities to analyse processes of labour market integration during various periods of economic development in Finland, in combination with the individualistic character of the labour careers of immigrants, this research is beneficial owing to the many various findings concerning labour market integration of immigrants. The approach undertaken in this research has a dualistic “descriptive-dynamic” character under which integration is understood as a never-ending process, which is conditioned by a time period of long-term existence and a context of solitary action. We find that transitions out of unemployment spells have a cyclical character; after every new “cycle” in unemployment, the probability of terminating unemployment decreases further. We also find that ascriptive factors make sense in the process of job-placement of immigrants from unemployment. Therefore, the gender, education and age of immigrants, as well as the effect of the period in which first unemployment occurred, potentially predict transitions out of unemployment and further labour market integration of immigrants.

The allosteric SERCA (Sarcoplasmic/Endoplasmic Reticulum Ca2+-ATPase) activator CDN1163 has been recently added to the group of pharmacological tools for probing SERCA function. We chose to investigate the effects of the compound on T lymphocyte Ca2+ stores, using the well-described Jurkat T lymphocyte as a reliable cell system for Ca2+ signaling pathways. Our study identified the lowest concentrations of the SERCA inhibitors thapsigargin (TG) and 2,5-di-(tert butyl)-1,4-benzohydroquinone (tBHQ) capable of releasing Ca2+, permitting the differentiation of the TG-sensitive SERCA 2b Ca2+ store from the tBHQ-sensitive SERCA 3 Ca2+ store. We proceeded to test the effects of CDN1163 on Ca2+ stores, examining specific actions on the SERCA 2b and SERCA 3 Ca2+ pools using our low dose SERCA blocker regimen. In contrast to previous work, we find CDN1163 exerts complex time-sensitive and SERCA isoform-specific actions on Ca2+ stores. Surprisingly, short-term exposure (0-30 minutes) to CDN1163 perturbs T cell Ca2+ stores by suppressing Ca2+ uptake with diminished Ca2+ release from the SERCA 2b-controlled store. Concomitantly, we find evidence for a SERCA-activating effect of CDN1163 on the SERCA 3 regulated store, given the observation of increased Ca2+ release inducible by low dose tBHQ. Intriguingly, longer-term (&gt;12 hours) CDN1163 exposure reversed this pattern, with increased Ca2+ release from SERCA 2b-regulated pools, yet decreased Ca2+ release responses from tBHQ-sensitive SERCA 3 pool. Our results reveal differential effects of CDN1163 on Ca2+ stores regulated by distinct SERCA isoforms, prompting the need for careful interpretation of the compound’s effects, particularly in cells expressing multiple SERCA isoforms.

The aim of this study is to analyze the characteristics of drought such as intensity, cumulative curves and trends, based on SPEI (Standardized Precipitation Evapotranspiration Index) at 8 stations in Korea from 1981 to 2010. The traditional SPEI is based on Thornthwaite equation for estimating evapotranspiration; SPEI_th. However, a standard of agricultural water management in Korea suggests FAO Penman-Monteith equation; SPEI_pm. In this study, we analyzed the intensity and trends of drought using SPEI_th and SPEI_pm, respectively, and analyzed the relationship between them. Both of central and southern region, the SPEIs were below -1.0 (moderated drought) for the periods May-August in the representative drought year such as 1988, 2001, and 2008-09. The frequency of drought was higher in southern region than central region. In addition, SPEI_pm showed slightly more intensive drought rather than SPEI_th except for Chuncheon and Gwangju. In 5 stations except for Cheoncheon, Gwangju and Jinju, the cumulative probability that SPEI_pm is below -1.5 was significantly increased from 1981-1995 to 1996-2010. As the results of drought trends, the increasing trend of SPEIs was shown on fall season, and the cumulative probability that SPEI_pm is below -1.5 was also significantly increased.

In this paper, the tensile behavior of unidirectional carbon/epoxy prepreg is experimentally analyzed at varying loads and temperatures, focusing on the considerable nonlinearity at the beginning of the stress-strain curve. The high viscosity of this material presented difficulties in securely holding specimens during tensile testing. As a result, modifications were made to the conventional gripping method to enable the acquisition of reliable test data. Additionally, a longer gauge length was chosen to minimize the impact of slippage on the elastic modulus measurement. To support the experiment, a micromechanical model of a prepreg tow with fiber waviness is proposed. An RVE model of periodically distributed unidirectional waved cylindrical fibers embedded within the matrix is developed to predict the effective material stiffness parameters. Numerical results are presented for different amplitude-to-wavelength ratios which indicate the fiber waviness reduces the tensile modulus of the composite. The simulation results are in good agreement with the uniaxial tensile test of the prepreg tow.

This article focuses on the analysis of dynamics emerging in a Network of Hodgkin-Huxley Reaction-Diffusion equations. The network is forced with three external periodic stimulus input. A synchronization phenomenon is observed.

In network analysis, links depict the connections between each pair of network nodes. However, such pairwise connections fail to consider the interactions among more agents, which may be indirectly connected. Such non-pairwise or higher-order connections can be signified by involving simplicial complexes. The higher-order connections become even more noteworthy when it comes to neuronal network synchronization, an emerging phenomenon responsible for the many biological processes in real-world phenomena. However, involving higher-order interactions may considerably increase the computational costs. To confound this issue, map-based models are more suitable since they are faster, simpler, more flexible, and computationally more optimal. Therefore, this paper addresses the impact of pairwise and non-pairwise neuronal interactions on the synchronization state of 10 coupled memristive Hindmarsh-Rose neuron maps. To this aim, electrical, inner linking, and chemical synaptic functions are considered as 2- and 3-body interactions in three homogenous and two non-homogenous cases. The results show that through chemical pairwise and non-pairwise synapses, the neurons achieve synchrony with the weakest coupling strengths.

We received an Honorable Mention at the Gravity Research Foundation 2018 Awards for Essays on Gravitation by showing that a correct general relativistic interpretation of the Mössbauer rotor experiment represents a new, strong and independent, proof of Einstein's general theory relativity (GTR). Here we correct a mistake which was present in our previous computations on this important issue by deriving a rigorous computation of the additional effect of clock synchronization. Finally, we show that some recent criticisms on our general relativistic approach to the Mössbauer rotor experiment are incorrect, by ultimately confirming our important result.

Many cryptographic systems require random numbers, and weak random numbers lead to insecure systems. In the modern world, there are several techniques for generating random numbers, of which the most fundamental and important methods are deterministic extractors proposed by von Neumann, Elias, and Peres. Elias’s extractor achieves the optimal rate (i.e., information theoretic upper bound) h(p) if the block size tends to infinity, where h(·) is the binary entropy function and p is probability that each bit of input sequences occurs. Peres’s extractor achieves the optimal rate h(p) if the length of input and the number of iterations tend to infinity. The previous researches related to both extractors did not mention practical aspects including running time and memory-size with finite input sequences. In this paper, based on some heuristics, we derive a lower bound on the maximum redundancy of Peres’s extractor, and we show that Elias’s extractor is better than Peres’s one in terms of the maximum redundancy (or the rates) if we do not pay attention to time complexity or space complexity. In addition, we perform numerical and non-asymptotic analysis of both extractors with a finite input sequence with any biased probability under the same environments. For doing it, we implemented both extractors on a general PC and simple environments. Our empirical results show that Peres’s extractor is much better than Elias’s one for given finite input sequences under the almost same running time. As a consequence, Peres’s extractor would be more suitable to generate uniformly random sequences in practice in applications such as cryptographic systems.