MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

In this paper, we consider the generalized sextic functional equation \begin{align*} \sum_{i=0}^{7}{}_7 C_{i} (-1)^{7-i}f(x+iy) = 0. \end{align*} And by applying the fixed point theory in the sense of L. C\u adariu and V. Radu, we will discuss the stability of the solutions for this functional equation.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

Malocclusions have a continuously increasing prevalence from a generation to another as a result of climate changes, soil, atmosphere and water pollution. All of these aspects have unfavorable consequences on the nutritional scheme. Thus, nutrition together with other etiopathogenic factors contribute to complex alterations in the somatic development of the entire organism and, implicitly, of the cephalic extremity. The study group included 4147 children from randomly selected schools from Vâlcea County, Romania. The aim of this study is to determine the prevalence of malocclusions in schoolchildren from Vâlcea County, Romania, according to the three main classes of malocclusions (according to Angle’s classification), age groups (from 6 to 10 years old and from 11 to 14 years old), gender (male and female) and place of origin (rural and urban). For Angle class I malocclusions we recorded the highest prevalence (48,78% from the total number of schoolchildren with malocclusions), followed by Angle class II malocclusions (45,85% from the total number of schoolchildren with malocclusions) and for Angle class III malocclusions we found the lowest prevalence (5,37% from the total number of schoolchildren with malocclusions).According to gender, we found the highest prevalence in female gender (29,90% from the total number of female subjects), while in male gender we recorded a prevalence of 27,70% from the total number of male subjects. Regarding the place of origin, there is a higher prevalence of malocclusions in the urban areas (29,16%). The study subgroup included 140 children randomly selected from the total number of subjects from the study group. They were included in a more advanced study. The aim is to find potential associations between the presence of malocclusions and various oral variables. Categorical variables were expressed as numerical values and percentages, and their association was evaluated with either the Chi-square test of association or homogeneity, or the Fisher Exact test. The acquired data were incorporated into a binomial logistic regression model to assess the likelihood of developing malocclusions in relation to the following variables: defective phonation, bruxism, frequency of teeth brushing, onychophagia, oral respiration, infantile deglutition, placing objects between the maxillaries, thumb sucking and salivary aspects. It is also aimed to compare the results obtained with similar ones from the specialized literature.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

In this paper, the fixed-time stabilization problem for a class of uncertain chained system is addressed by using a novel nonsingular recursive terminal sliding mode control approach. A fixed-time controller and an adaptive law are designed to guarantee the uncertain chained form system both Lyapunov stable and fixed-time convergent within the settling time. The advantage of the controller based on the sliding mode is that the settling time does not depend on the system initial state. Furthermore, we use RBF neural network to estimate the uncertainty of the system. Finally, the simulation results demonstrate the performance of the control laws.

This study investigates the fixed-time consensus-based attitude control problem for large telescope on-orbit construction subject to discrete-time communication, unknown tiny disturbance torque, model uncertainty, and actuator saturation under an undirected communication graph. Motivated by the need to save wireless communication resources, the communication scheme was designed to exploit interference, which can save communication resources in proportion to the number of modular unit mirrors. Then, a fixed-time observer with discrete-time communication was proposed, which also handles the unknown channel attenuation problem when exploiting information interference. Moreover, based on the backstepping procedure and the suitably defined adaptive compensation law, the fixed-time attitude consensus control law was proposed to handle unknown tiny disturbance torque, model uncertainty, and actuator saturation. Finally, comparative simulation results were provided to verify the effectiveness of the fixed-time observer and proposed fixed-time control law.

In this paper, a class of coupled competitive neural networks, which subject to disturbance and discontinuous activation functions, is concerned. To realize the fixed-time quasi-bipartite synchronization, an aperiodic intermittent controller is initially designed. Subsequently, by combining the fixed-time stability theory and nonsmooth analysis, several criteria are established to ensure the bipartite synchronization in fixed time. Moreover, synchronization error bounds and settling time estimates are provided. Finally, numerical simulations are presented to verify the main results.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

Incremental stability analysis for time-delay systems has attracted more and more attentions for its contemporary applications in transportation processes, population dynamics, economics, satellite positions, etc. This paper researches criteria on v(t)-incremental stability, which is defined to demonstrate the convergence rate for incremental stability, for time-delay systems. Firstly, the sufficient conditions for v(t)-incremental stability for time-delay systems with continuous right-hands are studied, and several corollaries for specific cases are provided. As for time-delay systems with discontinuous right-hands, after expounding the relevant conditions for the existence and uniqueness of the Filippov solution, by using approximation methods, sufficient conditions for v(t)-incremental stability are obtained. The conclusions are applied to linear switched time-delay systems and Hopfield neural network system with composite right-hand afterwards.

For a dynamical system, it is known that the existence of a Lyapunov density implies almost global stability of an equilibrium. It is then natural to ask whether the existence of a common Lyapunov density for a nonlinear switched system implies almost global stability, in the same way as a common Lyapunov function implies global stability for nonlinear switched systems. In this work, the answer to this question is shown to be affirmative as long as switchings satisfy a dwell-time constraint with an arbitrarily small dwell time. As a straightforward extension of this result, we employ multiple Lyapunov densities in analogy with the role of multiple Lyapunov functions for the global stability of switched systems. This gives rise to a minimum dwell time estimate to ensure almost global stability of nonlinear switched systems, when a common Lyapunov density does not exist. The results obtained for continuous-time switched systems are based on some sufficient conditions for the almost global stability of discrete-time non-autonomous systems. These conditions are obtained using the duality between Frobenius-Perron operator and Koopman operator.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

This research addresses a gap in the literature by conducting a comprehensive analysis of patients’ level of satisfaction with dental care. Methods: By combining quantitative and qualitative survey methods with the PSQ questionnaire this study aims to augment ongoing initiatives to enhance dental patients’ experiences by painting a more comprehensive depiction of patients' level of satisfaction; Results: When asked about their overall level of satisfaction 77,1% of the patients said they received excellent services from the office personnel and 72,2% said they trust their doctors; Conclusions: Assessing patient satisfaction in the realm of dental services quality is crucial for enhancing service quality and accuracy, benefiting both patients and dentists, and ultimately improving public health.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

This paper aims to introduce the notions of various types of Qc-contractions for which we establish some fixed circle and fixed disc theorems in the setting of metric spaces. Some illustrative examples are also provided to support our results. Moreover, we present some fixed circle and fixed disc results of integral type contractive self-mappings.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

Efficient fixed crane position analysis is critical in precast buildings construction to maximize lifting efficiency for precast elements. The primary objective is to minimize the travel distances of fixed cranes, thereby enhancing operational efficiency and cost control. This involves strategically reducing the distances between the transport truck parking, where elements are stored, the fixed crane, and the construction installation point. Despite its significance, existing studies often overlook the dynamic movement efficiency of transport trucks, particularly when dealing with multiple transport trucks and various models of fixed cranes, rendering the opti-mization of this scenario a challenging NP-hard problem susceptible to combinatorial explosion. This study presents a novel mathematical model leveraging the Genetic Algorithm (GA). The model aims to solve optimal model and position of fixed cranes, along with identifying ideal positions for transport truck parking. The study's methodology is validated and demonstrated through a project case study. Comparative analyses between the proposed model and the original planning underscore a noteworthy 6% reduction in both duration and costs when lifting elements directly from transport trucks, as opposed to establishing an on-site stock yard. Furthermore, the developed GA exhibits a substantial improvement in final solutions, achieving a remarkable 30% reduction in both operational duration and costs. This research contributes valuable insights into fixed crane position analysis of precast building construction, providing foundation for enhanced operational efficiency and cost-effectiveness in the industry.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

This work investigates the sliding mode control (SMC) problem for a class of uncertain switched systems subject to asynchronous switching and an assigned finite time constraint. Two important issues are how to ensure the reachability of state trajectories within the assigned time and the input-to-output finite-time stability (IO-FTS) of the closed-loop switched systems during the whole phase under asynchronous switching. To achieve these objectives, an asynchronous sliding mode controller with adjustable parameters is constructed to drive the state trajectories onto the sliding surface during the assigned finite-time interval. By means of the partitioning strategy, sufficient conditions for the IO-FTS of the closed-loop switched are derived during the whole phase [0,T] using the multiple Lyapunov function (MLF) approach. Additionally, the asynchronous characteristics are detailedly investigated while analyzing the reachability of a specified sliding surface. Finally, an illustrative example is given to illustrate the effectiveness of the proposed method.

In this paper, Lyapunov-Razumikhin technique, design of state-dependent switching laws, a fixed point theorem and variational methods are employed to derive the existence and the unique existence results of (globally) exponentially stable positive stationary solution of delayed reaction-diffusion cell neural networks under Dirichlet zero boundary value, including the global stability criteria \textbf{in the classical meaning}. Next, sufficient conditions are proposed to guarantee the global stability invariance of ordinary differential systems under the influence of diffusions. New theorems show that the diffusion is a double-edged sword in judging the stability of diffusion systems. Besides, an example is constructed to illuminate that any non-zero constant equilibrium point must be not in the phase plane of dynamic system under Dirichlet zero boundary value, or it must lead to a contradiction. Next, under Lipschitz assumptions on active function, another example is designed to prove that the small diffusion effect will cause the essential change of the phase plane structure of the dynamic behavior of the delayed neural networks via a Saddle point theorem. Finally, a numerical example illustrates the feasibility of the proposed methods.

This research investigates the intricate dynamics between intellectual Capital (VAIC) and the stability of banks in the evolving context of Saudi Arabia's banking sector. Against the backdrop of rapid economic reforms under Vision 2030 and the challenges imposed by the COVID-19 pan-demic, the research provides a nuanced analysis of how intellectual capital and intellectual capital's components—Human Capital Efficiency (HCE), Structural Capital Efficiency (SCE), and Capital Employed Efficiency (CEE)—affect the financial stability of Saudi banks. The research analyses a decade-long panel dataset from 2012 to 2022, utilizing both fixed effects and cross-section random effects models to discern the impact of intellectual capital on bank stability. The findings reveal a positive overall influence of intellectual capital on bank stability; however, individual compo-nents present a complex relationship, with CEE showing a positive association and HCE and SCE demonstrating unexpected negative correlations with bank stability. The research identifies lev-erage (LEV) as a significant factor negatively impacting stability. Operational efficiency (OPEF) and size (SIZE) also negatively affect stability. Surprisingly, macroeconomic indicators and bank size exhibit non-significant effects on bank stability. Similarly, the direct impact of the COVID-19 pandemic was found to be non-significant, suggesting a resilient banking environment or the presence of effective mitigating strategies. As Saudi Arabia continues its ambitious economic transformation, this research underscores the critical role of effectively managed intellectual capital in ensuring the banking sector's stability. It provides a foundation for ongoing research in this vital area.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

This work investigates the stability conditions for linear systems with time-varying delays via augmented Lyapunov-Krasovskii functional(LKF). Two types of augmented LKFs with cross terms in integral are suggested to improve the stability conditions for interval time-varying linear systems. Through this work, the compositions of the LKFs are considered to enhance the feasible region of stability criterion for linear systems. Mathematical tools such as Wirtinger-based integral inequality(WBII), zero equalities, reciprocally convex approach, and Finsler’s lemma are utilized to solve the problem of stability criteria. Two sufficient conditions are derived to guarantee the asymptotic stability of the systems using linear matrix inequality(LMI). First, asymptotic stability criteria are induced by constructing the new augmented LKFs in Theorem 1. And then simplified LKFs in Corollary 1 are proposed to show the effectiveness of Theorem 1. Second, asymmetric LKFs are shown to reduce the conservatism and the number of decision variables in Theorem 2. Finally, the advantages of the proposed criteria are verified by comparing maximum delay bounds in two examples. Two numerical examples show that the proposed Theorem 1 and 2 obtained less conservative results than existing outcomes. Also, Example 2 shows that the asymmetric LKF methods of Theorem 2 can provide larger delay bounds and fewer decision variables than Theorem 1’s in some specific systems.

A sufficient condition for the almost global sta-bility of nonlinear switched systems under average dwell timerestriction is obtained. This condition is derived leaning uponthe existence of multiple Lyapunov densities, which are associ-ated to subsystems and satisfy some compatibility conditions.An upper bound for the average dwell time that ensures almostglobal stability is obtained.

Emission trading schemes (ETSs) have become vital tools in striving toward global emission reduction objectives and promoting a sustainable economy. This paper empirically investigates the impact of market conditions on interconnectedness within precious metals, clean energy, green bonds, and carbon markets, focusing on China and the EU ETSs as the study subjects. A TVP-VAR-based asymmetric connectedness approach is adopted to capture the evolving relationships between the variables of interest in the time–frequency domain. The empirical findings reveal that: First, time-varying asymmetric connectedness and spillover effects among clean energy, precious metals, green bonds, and carbon markets are identified in both time and frequency domains under diverse market conditions, with long-term connectedness asymmetry being particularly sensitive, although spillovers exhibit variations. Second, the role and intensity of net transmitters or receivers vary across market conditions and frequency domains, indicating the complex and nuanced nature of market interactions. The EU ETS demonstrates a higher level of connectivity with global markets for clean energy, precious metals, and green bonds when compared to the Chinese ETS. However, it also shows greater susceptibility to fluctuations in market conditions. These results have significant implications for both investors striving to build sustainable diversified portfolios and regulators endeavoring to craft effective policies for risk regulation and sustainable development.

Mapping forest composition using multiseasonal optical time series is still challenging. Highly contrasted results are reported from one study to another suggesting that drivers of classification errors are still under-explored. We evaluated the performances of single-year Formosat-2 time series to discriminate tree species in temperate forests in France and investigated how predictions vary statistically and spatially across multiple years. Our objective was to better estimate the impact of spatial autocorrelation in the validation data on measurement accuracy and to understand which drivers in the time series are responsible for classification errors. The experiments were based on ten Formosat-2 image time series irregularly acquired during the seasonal vegetation cycle from 2006 to 2014. Due to lot of clouds in the year 2006, an alternative 2006 time series using only cloud-free images has been added. Thirteen tree species were classified in each single-year dataset based on the SVM algorithm. The performances were assessed using a spatial leave-one-out cross validation (SLOO-CV) strategy, thereby guaranteeing full independence of the validation samples, and compared with standard non-spatial leave-one-out cross-validation (LOO-CV). The results show relatively close statistical performances from one year to the next despite the differences between the annual time series. Good agreements between years were observed in monospecific tree plantations of broadleaf species versus high disparity in other forests composed of different species. A strong positive bias in the accuracy assessment (up to 0.4 of Overall Accuracy) was also found when spatial dependence in the validation data was not removed. Using the SLOO-CV approach, the average OA values per year ranged from 0.48 for 2006 to 0.60 for 2013, which satisfactorily represents the spatial instability of species prediction between years.

Quantum gravity theories rely on a minimal measurable length for their formulations, which clashes with the classical formulation of the uncertainty principle and with Lorentz invariance from general relativity. These incompatibilities led to the development of the generalized uncertainty principle (GUP) from string theories and its various modifications. GUP and covariant formulations of the uncertainty principle are discussed, together with implications for space-time quantization.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Abscisic acid (ABA) plays a major role in promoting ripening in sweet cherry, a non-climateric fruit. Exogenous application of ABA has been performed to study fruit ripening and cracking, but this growth regulator is not used for commercial production. To determine the potential of this growth regulator to improve sweet cherry fruit quality, ABA canopy spraying was assayed in four cultivars. Canopy spraying of S-ABA significantly: 1) enhanced sweet cherry fruit color in ‘Glenred’, ‘Lapins’ and 'Bing' cultivars, but not in ‘Royal Rainier’ (a bi-colored cultivar), and 2) decreased fruit size and firmness in ‘Lapins’, ‘Bing’ and ‘Royal Rainier’. Seasonally reproducible effects were seen in ‘Lapins’ (mid/late-maturing) but not in ‘Glenred’ (early-maturing). Canopy spraying of nordihydroguaiaretic acid (NDGA) decreased color and increased fruit size in ‘Lapins’, but not in ‘Glenred’. Direct application of ABA on fruits attached to the tree, without application to the foliage, increased Lapins' fruit color without reducing size. These results suggest a localized fruit response to exogenous ABA application on fruit color development, but that a decrease in fruit size may be due to the effects of exogenous ABA on the tree canopy foliage.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

The time-dependent behavior and long-term stability of deep-buried tunnels in soft rocks have received lots of considerations in tunnel engineering and allied sciences. To better explore and deepen the engineering application of rock creep, extensive research studies are still needed, although fruitful outcomes have already obtained in many related investigations. In this article, the Weilai Tunnel in China’s Guangxi province is studied taking its host rocks as the main research object. In fact, aiming at forecasting the time-varying deformation of this tunnel, a novel elasto-visco-plastic creep constitutive model with two variants is proposed, by exploiting the typical complex load-unload process of rock excavation. The model is well validated and good agreements are found with the relevant experimental data. Moreover, the time-dependent de-formation rules are properly established for the surrounding rocks, by designing two new closed-form solutions based on the proposed creep model and the Hoek-Brown criterion. The convergence deformations calculated from the closed-form solutions conform well to the on-site monitoring data. In only 27 days after excavation, the creep deformation of the Weilai tunnel overtakes 400 mm, which is enormous. To guarantee the long-term stability of this tunnel, a ro-bust support scheme and its long-term monitoring with appropriate remote sensors are strongly suggested.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p&lt;0.05; p&lt;0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p&lt;0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

This paper presents the results of investigations on the pyrolysis of tyres waste in a laboratory fixed bed batch reactor. The results regarding the influence of either the reaction temperature (425, 450, 475, and 500 °C) and the flow of the inert gas (0, 100, 300, and 500 mL/min) on products yield (referred to pyrolysis of waste tyres) are also considered and discussed. On the basis of the above mentioned findings, the most appropriate experimental conditions were selected to contribute to a higher yield of pyrolysis oil. The sample of pyrolysis oil obtained from the experiments carried out in the selected optimal conditions (reaction time 120 min, temperature 450 °C and the inert gas flow of 100 mL/min) was subjected to a calorimetric and infrared spectroscopy analysis. The results of IR spectroscopy analysis on this oil sample showed the following content in percentages (by mass): 32.59 % of aromatics, 51.06 % of paraffins and 16.35 % of naphthenes. The pyrolysis oil so obtained has a high calorific value (42 MJ/kg) and a low sulfur content (0.41 % by mass), which makes it an excellent raw material for energy production. The solid product, i.e. pyrolysis char or carbon black, has the potential to be used as an adsorbent or catalyst support after an activation process, which changes its irregular pore structure to a more voluminous one, making the overall structure more crystalline and symmetrical. Pyrolysis coal has a fairly high calorific value of 31 MJ/kg, when compared to typical solid fuels, so it can be used in energy production or as a feedstock for the gasification process.

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

Rivaroxaban and aspirin are commonly used antithrombotic agents that are used in combination for the prevention of coronary artery disease (CAD) and atherothrombotic events in adult patients after an acute coronary syndrome (ACS) with elevated cardiac biomarkers, or with coronary artery disease (CAD) or symptomatic peripheral artery disease (PAD) in high-risk patients. The recommended dosage is 2.5 mg Rivaroxaban twice daily with 75–100 mg aspirin daily. This study aimed to develop a fixed-dose combination tablet of rivaroxaban (2.5 mg) and aspirin (50 mg) to decrease the patient's pill burden and enhance medication adherence. The product formula was developed based on compatibility studies among the active ingredients and the active ingredients' compatibility studies. The formula and the manufacturing procedure were chosen based on the risk assessment for each active substance, wet granulation with both actives intragranular was found to have faster dissolution than direct mix formulae. Furthermore, a validated reverse-phase HPLC stability indicator method was developed to detect APIs and their possible degradants in the formula.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

In this paper, we prove some common fi xed point theorems on complex partial metric space. The presented results gener- alize and expand some of the literature well-known results. We also explore some of the application of our key results.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Oncological patients need the proper doses of medications to facilitate their recovery. The two basic approaches used in dosing Monoclonal Antibodies (mAbs) are fixed-dose combination and variable dosing. In Fixed-Dose Combination Drugs (FDCs), two or more active components are combined in a single formulation at a predetermined dose. Variable dosage, which has long been the industry standard, is the polar opposite of this approach. The body changes over time; the Body Surface Area (BSA) in square meters is often used as a Measure (m2). This study uses a systematic review. Most mAbs used in oncology are predominantly given as cytotoxic anticancer drugs using body-size-based (variable) regimens. Despite the benefits of fixed-dose, variable dosing has become the industry standard, despite being criticized for ineffectiveness. While variable dosing has some advantages, the prevalent view is that continuous dosing has significant advantages based on the balance of probabilities. After assessing each alternative, including its benefits and drawbacks, history of use, and suitability in the current context, fixed dosing emerges as a viable option.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.

Creep is a fundamental property naturally exists in some types of rock, which is significant for the long-term stability of roadways during the mining process. In this paper, the long-term strength of coal and rock were obtained via laboratory experiments, and a Cvisc elasto-viscoplastic model was adopted and introduced in FLAC3D, based on the 3101 transport roadway in Hongqinghe Coal Mine, to investigate the influence of creep on the stability of deep-high stress roadway. The test results show that the long-term strength of 3-1 coal and sandy mudstone, respectively, is 18.65 MPa, 39.95 MPa. The plastic zone, the deformation, and the damage of roadway surrounding rock behave an obvious increase after being excavated for 720d as the creep model was chosen. The plastic zone failure with models shear-p (1090.7 m3), shear-n (381.7 m3), tension-n (98.4 m3), and tension-p (30.8 m3), the damage value has an obvious increment of increased 21.2% (0.053), the deformation increases in the order is two-sidewalls (1978 mm), roof (907 mm), floor (101 mm). The creep of the roadway can be divided into three stages: the accelerating stage, the decaying stage, and the stable stage. The creep speed of each stage is greatly affected by the presence or absence of anchor spray support: the creep speed of the bare roadway roof, roadway side, and floor stability, respectively, is 1.01, 1.02, and 0.12 mm/d; After anchor spray support, the creep velocity, correspondingly, decreased to 0.69, 0.37, and 0.12 mm/d, and the amount of surrounding rock damage decreased from 0.302 to 0.243. This indicates that the anchor spray support can significantly reduce the creep effect of the roadway. The Cvisc creep model was verified reliable and can provide guidance for deep high-stress coal roadway support.

The present work reports an experimental thermodynamic study of two nitrogen heterocyclic organic compounds, fenclorim and clopyralid, that have been used as herbicides. The sublimation vapor pressures of fenclorim (4,6-dichloro-2-phenylpyrimidine) and of clopyralid (3,6-dichloro-2-pyridinecarboxylic acid) were measured, at different temperatures, using a Knudsen mass-loss effusion technique. The vapor pressures of both crystalline and liquid (including supercooled liquid) phases of fenclorim were also determined using a static method based on capacitance diaphragm manometers. The experimental results enabled accurate determination of the standard molar enthalpies, entropies and Gibbs energies of sublimation for both compounds and of vaporization for fenclorim, allowing a phase diagram representation of the (p,T) results, in the neighborhood of the triple point of this compound. The temperatures and molar enthalpies of fusion of the two compounds studied were determined using differential scanning calorimetry. The standard isobaric molar heat capacities of the two crystalline compounds were determined at 298.15 K, using drop calorimetry. The gas phase thermodynamic properties of the two compounds were estimated through ab initio calculations, at the G3(MP2)//B3LYP level, and their thermodynamic stability was evaluated in the gaseous and crystalline phases, considering the calculated values of the standard Gibbs energies of formation, at 298.15 K.

In a particle swarm with a fixed kinetic energy, the constituent particles move randomly and their velocity magnitudes follow a Maxwell distribution characterized by specific parameters. Within a certain time frame, particles in a sub-swarm may exhibit a bias in their movement direction. Thus, the particles may exhibit a special characteristic (biased random motion), where the group velocity in a particular direction remains constant u. For this biased particle swarm, composed of randomly moving particles with a fixed average speed c, particles have a higher probability of moving in a specific direction. Conversely, their likelihood of moving in all other directions is equally reduced. This study starts from the perspective of biased random walks and using Mathematica software proves that the diffusion rate of particles (in the reference frame R_u observed from R₀) in all directions is slower than that of an unbiased particle swarm with the same average speed c. Specifically, the degree of reduction is determined by the Lorentz-like factor. Lastly, we present the Ito equation for this biased random motion and provide associated verification examples. This study aims to serve as a reference for comprehending the underlying principles of the special relativity effect.

Humankind has entered a new era wherein a main characteristic is the convergence of various technologies providing services exerting major impact upon all aspects of human activity, be it social interactions as well as interactions with the natural environment. Fixed networks are about to play a major role in this convergence, since they form, along with mobile networks, the backbone that provides access to a broad gamut of services, accessible from any point of the globe. It is for this reason that we introduce a forward-looking approach for fixed networks, particularly focused on Fixed 6th Generation (F6G) networks. First, we adopt a novel classification scheme for the main F6G services, comprising six categories. This classification is based on the key service requirements, namely latency, capacity and connectivity. F6G networks differ from those of previous generations (F1G-F5G) in that they concurrently support multiple key requirements. We then propose concrete steps towards transforming the main elements of fixed networks, such as optical transceivers, optical switches etc. such that they satisfy the new F6G service requirements. Our study categorizes the main networking paradigm of optical switching into two categories namely ultra-fast and ultra-high capacity switching, tailored to different service categories. With regard to the transceiver physical layer, we propose: a) use of all-optical processing to mitigate performance barriers of analog to digital and digital to analog converters (ADC/DAC); b) exploitation of optical multi-band transmission, space division-multiplexing and adoption of more efficient modulation formats.

In this article, we show the existence of fixed point for the derivative of interval-valued functions. Meanwhile, the fixed point inquiry will utilize the common fixed point methods under the condition of compatibility of the hybrid composite mappings in the sense of the Hausdorff metric. Some examples are given to support the usability of the result of this research .

In this paper, we study a three step iterative scheme to approximate fixed points of Suzuki's generalized non-expansive mappings. We establish some weak and strong convergence results for such mappings in uniformly convex Banach spaces. Further, we show numerically that iterative scheme (1.8) converges faster than some other known iterations for Suzuki's generalized non-expansive mappings. To support our claim, we give an illustrative example and approximate fixed points of such mappings using Matlab program. Our results are new and generalize several relevant results in the literature.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p&lt;0.001), DAPT (p&lt;0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

The vocal folds are found in the larynx and their vibrations produce the voice. Little is known about morphology and the size of cattle larynx. The aim of the study was to quantify the shape asymmetry of the vocal folds in calves obtained post-mortem using a geometric morphometric approach. A sample of 14 larynges from calves (in an age range 335 to 625 days) belonging to “Bruna dels Pirineus” breed and its F1 crosses was obtained in an abattoir during the first semester of 2021. Landmark sets were superimposed on images of fixed transverse sections of larynges. Using geometric morphometric techniques, we analysed the presence of asymmetries. Results demonstrate differences between right and left vocal fold sides as directional asymmetry, at least in fixed structures. Our findings provide a foundation for quantifying the possible contribution of vocal organ asymmetry among cattle. This study can be considered the first to detect vocal fold asymmetries in cattle. Studies with a larger sample size are needed to validate the information in large populations. One limitation is that the present study does not have samples from adult animals, so it would be interesting to know if the results are similar among them.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

The oil and gas sector has recognised structural integrity assessment of ageing platform for prospective life extension as a rising concern, particularly in encountering the randomness of the harsh ocean environments. This condition leads to uncertainty in wave-in-deck load estimates and a high load level being imposed on offshore structures. This emphasises the necessity of enhanced reliability, as failure might result in inaccessibility because of the uncertainties related to long-distance services, such as accuracy of predictions of loads and responses. Even though the established guidelines present a fundamental assessment, additionally, comprehensive rules are required. This paper performed a reliability analysis incorporating practical approaches that can more accurately represent time-dependent structural deterioration. The following two procedures have been adopted by a majority of significant oil and gas operators to monitor the safety and integrity of these structures: a) Ultimate Strength Assessment (USA) method and b) Reliability Design Assessment (ReDA) method. A comparison of these two reliability approaches was performed on selected ageing jacket structures in the region of the Malaysian sea. The comparative findings, namely, reserve strength ratio (RSR) at various years of the return period (RP) and ratio value for risk of failure regarding the probability of failure (POF), provided a check and balance in strengthening confidence in the results. The findings showed that the structural components might safely survive either using the USA and ReDA method in such conditions, as the reliability indexes were determined to be satisfactory compared to allowable values from ISO 19902 design specifications. Therefore, these evaluations were determined to control the risk level of the structure during the remaining of its lifetime and undertake cost-effective inspections or mitigation strategies when necessary.

Pain is an unpleasant emotional and sensory experience. For many years orthodontists have been looking for an effective method of reducing this feeling of discomfort. In recent years, low-level laser therapy (LLLT) has taken hold in the orthodontic field. Among the countless advantages it can modulate the painful feeling. The aim of this research is to identify the use of photobiomodulation in subjects undergoing fixed orthodontic treatment, to reduce the pain and discomfort that it causes. The research was conducted from the Web of Science, Pubmed and Scopus databases. Only 14 of all articles met the inclusion and exclusion criteria and were therefore used to conduct the research. The different studies compared, in most cases, patients whose mouth was divided into a part treated with laser therapy and a placebo part. The results show a statistically significant difference in perceived pain between the irradiated arch and the non-irradiated arch. Three authors didn’t find statistically significant results in favour of low-laser therapy, but it is important to remember that they used different parameters. To obtain generally valid studies, with consistent and reproducible results, it is necessary to standardize the different parameters used that are independent by operator performing the procedure.

We consider the problem of calibrating distance measurement of Light Detection and Ranging (lidar) sensor without using additional hardware, but rather exploiting assumptions on the environment surrounding the sensor during the calibration procedure. More specifically we consider the assumption of calibrating the sensor by placing it in an environment so that its measurements lie in a 2D plane that is parallel to the ground, and so that its measurements come from fixed objects that develop orthogonally w.r.t. the ground, so that they may be considered as fixed points in an inertial reference frame. We moreover consider the intuition that moving the distance sensor within this environment implies that its measurements should be such that the relative distances and angles among the fixed points above remain the same. We thus exploit this intuition to cast the sensor calibration problem as making its measurements comply with this assumption that “fixed features shall have fixed relative distances and angles”. The resulting calibration procedure does thus not need to use additional (typically expensive) equipment, nor deploying special hardware. As for the proposed estimation strategies, from a mathematical perspective we consider models that lead to analytically solvable equations, so to enable deployment in embedded systems. Besides proposing the estimators we moreover analyse their statistical performance both in simulation and with field tests, reporting thus the dependency of the MSE performance of the calibration procedure as a function of the sensor noise levels, and observing that in field tests the approach can lead to a ten-fold improvement in the accuracy of the raw measurements.

In this paper, the notion of θ∗-weak contraction is introduced, which is utilized to prove some fixed point results. These results are helpful to give a positive response to certain open question raised by Kannan [Amer. Math. Monthly 76:1969] and Rhoades [Contemp. Math. 72:1988] on the existence of contractive definition which does not force the mapping to be continuous at the fixed point. Some illustrative examples are also given to support our results. As applications of our result, we investigate the existence and uniqueness of a solution of non-linear matrix equations and integral equations of Volterra type as well.

A fundamental tool in mathematical physics is the logarithmic Sobolev inequality. A quantitative version proven by Carlen with a remainder involving the Fourier-Wiener transform is equivalent to an entropic uncertainty principle more general than the Heisenberg uncertainty principle. In the stability, the remainder is in terms of an entropy, not a metric. Recently, a stability result for H¹ was obtained by Dolbeault, Esteban, Figalli, Frank, and Loss in terms of an L^p norm. Afterwards, Brigati, Dolbeault, and Simonov discussed the stability problem involving a stronger norm. A full characterization with a necessary and sufficient condition to have H¹ convergence is identified in this paper. Moreover, an explicit H¹ bound via a moment assumption is shown. Also, the L^p stability of Dolbeault, Esteban, Figalli, Frank, and Loss is proven to be sharp.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

Leishmaniasis is the third most common vector-borne disease and a very important protozoan infection. Cutaneous leishmaniasis is one of the most common types of leishmaniasis infectious diseases with up to 2 million occurrences of new cases each year worldwide. A dynamic transmission multivariate time series model was applied to the data to account for overdispersion and evaluate the effects of three environmental layers as well as seasonality in the data. Furthermore, ecological niche modeling was used to investigate the geographical suitable conditions for cutaneous leishmaniasis using temperature, precipitation and altitude as environmental layers, together with the leishmaniasis presence data. A retrospective analysis of the cutaneous leishmaniasis spatial data in Afghanistan between 2003 and 2009 indicates a steady increase from 2003 to 2007, a small decrease in 2008, then another increase in 2009. An upward trend and regularly repeating patterns of highs and lows was observed related to the months of the year which suggests seasonality effect in the data. Two peaks were observed in the disease occurrence-- January to March and September to December -- which coincide with the cold period. Ecological niche modelling indicates that precipitation has the greatest contribution to the potential distribution of leishmaniasis.

Maintenance of intestinal barrier integrity is crucial for preventing inflammatory bowel diseases (IBDs) onset and exacerbations. In this work we study the effect of a fixed combination of Lactobacillus reuteri and Lactobacillus acidophilus and herbal extracts in an in vitro inflammation experimental model. Caco-2 cell monolayer was exposed to INF-γ+TNF-α or to LPS; Trans Epithelial Electrical Resistance (TEER) and paracellular permeability were investigated. ZO-1 and occludin tight junctions (TJs) were also investigated by mean of immunofluorescence. The pre-treatment with the fixed combination of probiotics and herbal extracts prevented the inflammation-induced TEER decrease, paracellular permeability increase and TJs translocation. In summary the fixed combination of probiotics and herbal extracts investigated in this research was found to be an interesting candidate for targeting the re-establishment of intestinal barrier function in IBDs conditions.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Dyslipidemia presents high levels of serum cholesterol, being characterized as a risk factor for cardiovascular diseases, especially for the development of atherosclerosis. E. oleracea (OFEO), A. esculentus (OFAE), B. orellana (OFBO) and granulated (CHR) oils are rich in bioactive compounds with potential to treat changes in lipid metabolism. This study investigated the effects of treatments with oils from A. esculentus, E. oleracea, B. orellana and granules (Chronic SM®) on saturated fat-induced dyslipidemia Cocos nucifera L. The chromatographic profile showed the majority of unsaturated fatty acids in the tested oils. The quantification of tocotrienols and geranylgeraniol was obtained in OFBO and CHR. Treatments with OFEO, OFAE, OFBO and CHR were able to significantly reduce glycemia with p&gt;0.001, as well as hypertriglyceridemia, total cholesterol and LDL-cholesterol, in addition to increasing HDL-cholesterol. The treatments inhibited the formation of atheromatous plaques in the vascular endothelium of the treated rats. The obtained results suggest that the OFEO, OFAE, OFBO and CHR groups have antidyslipidemic effects and antiatherogenic activity.

A study on flywheel geometries is presented here with the use of finite element modelling (FEM) simulations. The study analyses the stress behaviour of flywheel rotors subject to the rotational speed that creates the maximum stress that the flywheel can support, and then calculates the rotational energy mass ratio (energy density) for each geometry. The obtained geometry was Gaussian section for the Flywheel rotor. The used material for the simulations is carbon fibre Hexcel UHM 12000. The best results were a rotational speed of ≈279.000 rpm and rotational energy density of ≈ 440 Wh/kg for a single disk, but this keeps the total energy low. To increase the total energy, Flywheels with 2 and 3 rotors were analysed. Then the stability under rotation of these Flywheels were analysed, some instability was found and a solution was presented.

In this paper, we introduce a way of representing a given mapping as the sum of odd and even mappings. Then, by using this representation, we investigate the stability of various forms for the general nonic functional equation.

This review describes major advances in the use of functionalized molecular metal oxides (polyoxometalates, POMs) as water oxidation catalysts under electrochemical conditions. The fundamentals of POM-based water oxidation are described together with a brief overview of general approaches to designing POM water oxidation catalysts. Next, the use of POMs for homogeneous, solution-phase water oxidation is described together with a summary of theoretical studies shedding light on the POM-WOC mechanism. This is followed by a discussion of heterogenization of POMs on electrically conductive substrates for technologically more relevant application studies. Stability of POM water oxidation catalysts are discussed on selected examples where detailed data is already available. The review finishes with an outlook on future perspective and emerging themes in electrocatalytic polyoxometalate-based water oxidation research.

Modern portfolio theory claims that diversification into non-correlated or negatively correlated activities reduces the overall risk of a portfolio. Considering the total income of a bank as a portfolio of interest income and non-interest income, this paper investigates how the variability of interest income and non- interest income, and covariance between interest income and non-interest income influence the various risk factors of banks. We set out a study in the Indian context. We have extracted data for the period 2005-2017 and employed an extended version of Ridge, Lasso and Elastics Net regression to take care of multi-collinearly in our data. We have considered 10-fold cross-validation techniques to get optimal values of tuning parameters for Ridge, Lasso, and Elastics Net regression (which is a convex combination of ridge and the LASSO). We have compared different regression techniques by comparing RMSE and R2. We observe that non-interest income is positively correlated with interest income in the Indian context, but it does stabilize variance, idiosyncratic risk & market risk (Beta) of Indian Banks.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

This paper presents a mathematical modeling approach utilizing a fuzzy modeling framework for fixed wing aircraft systems with the goal of creating a highly desirable mathematical representation for model-based control design applications. The starting point is a mathematical model comprised of fifteen non-linear ordinary differential equations representing the dynamic and kinematic behavior applicable to a wide range of fixed wing aircraft systems. Here the proposed mathematical modeling framework is applied to the AIRBUS A310 model developed by ONERA. The proposed fuzzy modeling framework takes advantage of sector non-linearity techniquesto recast all the non-linear terms from the original model to a set of combined fuzzy rules. The result of this fuzzification is a more suitable mathematical description from the control system design point of view. Therefore, the combination of this fuzzy model and the wide range of control techniques available in the literature for such kind of models will enable us to avoid common control design methods, such as gain scheduling, where stability issues can be extremely challenging.

In this paper, a positive answer to the open question of Fabino et al. is given, and the concept of I\c sik type set valued contractions is introduced and fixed point theorem for such contractions is established. Examples to support main theorems are given, and an application to integral inclusion is given.

In this article, the concept of fuzzy $(\sigma,\mathcal{Z})$-contractive mapping has been introduced in fuzzy metric spaces which is an improvement over the corresponding concept recently introduced by Shukla et al. [Fuzzy Sets and system. 350 (2018) 85--94]. Thereafter, we utilized our newly introduced concept to prove some existence and uniqueness theorems in $\mathcal{M}$-complete fuzzy metric spaces. Our results extend and generalize the corresponding results of Shukla et al.. Moreover, an example is adopted to exhibit the utility of newly obtained results.

In the framework of a multiplicative metric space. We have discuss some Properties of convex structures in pseudo multiplicative metric space and have applied these properties toiobtain alfixed point results in complete pseudo. It would be interesting to prove some further results in such metric spaces with completeness property.