An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

In the FCC conversion of heavy petroleum fractions as atmospheric residues, the main challenge for refiners to achieve the quantity and quality of various commercial products depends essentially on the catalyst used in the process. A deep characterization of the catalyst at different steps of the process (fresh, regenerated, and spent catalyst) was investigated to study the catalyst's behavior including the physicochemical evolution, the deactivation factor, and kinetic-thermodynamic parameters. All samples have been characterized by various spectroscopy methods such as N2 adsorption-desorption, UV-visible spectroscopy, Raman spectroscopy, LECO carbon analysis, Scanning electron microscopy (SEM), X-ray diffraction (XRD), X‐ray fluorescence (XRF), nuclear magnetic resonance spectroscopy (NMR13C) analysis, and Thermogravimetric analysis. The results of N2 adsorption-desorption, UV-vis, Raman, LECO carbon, and SEM images showed that the main causes of catalyst deactivation and coking were the deposition of carbon species that covered the active sites and clogged the pores, and the attrition factor due to thermal conditions and poisonous metals. The XRD and XRF results showed the catalyst’s physicochemical evolution during the process and the different interlinks between catalyst and feedstock (Nickel, Vanadium, Sulfur, and Iron) elements which should be responsible for the coking and catalyst attrition factor. It has been found that, in addition to the temperature, the residence time of the catalyst in the process also has an influence on catalyst structure transformation. NMR13C analysis revealed that polyaromatic hydrocarbon is the main component in the deposited coke of the spent catalyst. Thermogravimetric analysis showed that the order of catalyst mass loss was fresh > regenerated > spent catalyst due to the progressive losses of the hydroxyl bonds (OH) and the structure change along the catalyst thermal treatment. Moreover, the kinetic and thermodynamic parameters showed that all zones are non-spontaneous endothermic reactions.

Associating the most influential parameters with the product distribution is of uttermost importance in complex catalytic processes such as fluid catalytic cracking (FCC). These correlations can lead to the information-driven catalyst screening, kinetic modeling and reactor design. In this work, a dataset of 104 uncorrelated experiments, with 64 variables, has been obtained in an FCC simulator using 6 types of feedstock (vacuum gasoil, polyethylene pyrolysis waxes, scrap tire pyrolysis oil, dissolved polyethylene and blends of the previous), 36 possible sets of conditions (varying contact time, temperature and catalyst/oil ratio) and 3 industrial catalysts. Principal component analysis (PCA) has been applied over the dataset, showing that the main components are associated with feed composition (27.41% variance); operational conditions (19.09%) and catalyst properties (12.72%). The variables of each component have been correlated with the indexes and yields of the products: conversion, octane number, aromatics, olefins (propylene) or coke, among others.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

In this work, the influence of catalyst reuse and reaction time on the yield and quality of organic liquid products (OLP) obtained in a cracking pilot plant at 450 °C and 1.0 atm has been systematically investigated. The distillation of OLP produced 04 (four) distilled fractions. The quality of the biofuels was certified by physical-chemical analysis, as well as FT-IR and GC-MS analysis. The experimental results showed the feasibility of applying the spent sodium carbonate twice in catalytic cracking of vegetable oils. The physical-chemical properties (density, viscosity, acid value, saponification value, and flash point) of OLP decrease as the reaction time increases. The distillation of OLP yields 62.35% (wt.), producing green-like gasoline, kerosene, and diesel fractions rich in hydrocarbons. Therefore, biofuels-like fractions produced by distillation of OLP have a great potential for replacing partially petroleum derived fuels.

The prediction of tertiary RNA structures is significant to the field of medicine (e.g. mRNA vaccines, genome editing), and the exploration of viral transcripts. Though many RNA folding software exist, few studies have condensed their locus of attention solely to viral pseudoknotted RNA. These regulatory pseudoknots play a role in genome replication, gene expression, and protein synthesis. This study explores five RNA folding engines that compute either the minimum free energy (MFE) or the maximum expected accuracy (MEA). These folding engines were tested against 26 experimentally derived short pseudoknotted sequences (20-150nt) using metrics that are commonly applied to software prediction accuracy (e.g. F1 scoring, PPV). This paper reports higher accuracy RNA prediction engines (pKiss) when compared to previous iterations of the software, and when compared to older folding engines. They show that MEA folding software does not always outperform MFE folding software in prediction accuracy when assessed with metrics such as percent error, sensitivity, PPV, and F1 scoring when applied to viral pseudoknotted RNA. Moreover, the results suggest that thermodynamic model parameters will not ensure accuracy if auxiliary parameters such as Mg2+ binding, dangling end options, and H-type penalties are not applied. The observations reported in this paper highlight the quality between different ab initio prediction methods while enforcing the idea that a better understanding of intracellular thermodynamics is necessary for a more efficacious screening of RNAs.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

A series of Ni/KIT6 catalystprecusors with 25wt.%Ni loading amount were reduced in H₂ at 400, 450, 500, and 550ºC, respectively. The studied catalysts were investigated by XRD, Quasiin-situ XPS, BET, TEM, and H₂-TPDanalysis methods.It was found that reduction temperature is an important factor affecting the hydrodeoxygenation (HDO) performance of the studied catalysts. The reduction temperature influences mainly the content of active components, crystal size, and the abilityfor adsorbing and activatingH2. The developed pore structure and large specific surface area of the KIT-6 support favored the Ni dispersion.The RT450 catalyst, which was prepared in H₂ atmosphere at 450 ºC, has the best HDO performance. Ethyl acetate can be completely transformed, and maintain 96.8% ethane selectivity and 3.2% methane selectivity at 300 ºC. The calculated apparent activation energies of the prepared catalysts increased in the following order: RT550 > RT400 > RT500 > RT450.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

A magnetite (CDC@Fe3O4) heterogeneous photocatalyst was synthesized via treated and modified cotton in two steps. The designed nanocomposites were characterized by FTIR, TGA, XRD, SEM, and VSM analyses. The Fenton-photocatalytic decomposition efficiency of the synthesized magnetic catalyst was evaluated under visible sunlight using Methyl Orange (MO) as a model organic pollutant. The impacts of several degradation parameters, including the light source, catalyst load, irradiation temperature, oxidant dose, and pH of the dye aqueous solution and its corresponding concentration on the Fenton photodegradation performance, were methodically investigated. (CDC@Fe3O4) heterogeneous catalyst showed a remarkable MO removal rate of 97.9% at 10 min under visible-light irradiation. (CDC@Fe3O4) nanomaterials were also used in a heterogeneous catalytic optimized protocol for a multicomponent reaction procedure to obtain nine tetra-substituted imidazole derivatives. The green protocol afforded imidazole derivatives in 30 min with good yields (91-97%) at room temperature and under ultrasound irradiation. Generally, a synthesized recyclable heterogeneous nano-catalyst is a good example and is suitable for wastewater treatment and organic synthesis.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The main objective of this work is the assessment of the annual number of hospital admissions for respiratory disease (HARD) due to the exposure to in-healable particulate matter (PM10), within the greater Athens area (GAA), Greece. Towards this aim, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) recorded in six monitoring stations located in the GAA, for a 13-year period 2001-2013, is used. Initially, a descriptive statistical treatment of PM10 concentrations took place. Furthermore, the AirQ2.2.3 software developed by the WHO was used to evaluate adverse health effects by PM10 in the GAA during the examined period. The results show that, during the examined period PM10 concentrations present a significant decreasing trend. Also, the mean annual HARD cases per 100,000 inhabitants ranged between 20 (suburban location) and 40 (city centre location). Approximately 70% of the annual HARD cases are due to city centre residents. In all examined locations, a declining trend in the annual number of HARD cases is appeared. Moreover, a strong relation between the annual number of HARD cases and the annual number of days exceeding the European Union daily PM10 threshold value was found.

Azo dyes are the most widely used synthetic dyes in the printing and dyeing process. However, the discharge of untreated azo dyes poses potential threat for human health and aqueous ecosystem. Herein, we fabricated a novel heterogenous catalyst - activated carbon fiber-supported ferric alginate (FeAlg-ACF) . Together with peroxymonosulfate (PMS) and visible light, this photocatalytic oxidation system was used to remove an azo dye - azophloxine. The results indicated that the proposed catalytic oxidation system can remove 100% azophloxine within 24 min, while under the same system, the removal rate was only 92 % and 84 % when ferric alginate was replaced with ferric citrate and ferric oxalate respectively, which showed the superiority of activated carbon fiber-supported ferric alginate. The degradation of azophloxine is achieved by the active radicals (SO4•− and •OH) released from PMS and persistent free radicals from activated carbon fiber. After treating for 24 min, the total organic carbon of azophloxine solution (50 μmol/L) decreased from 1.82 mg/L to 79.3 μg/L and the nitrate concentration of ions increased from 0.3 mg/L to 8.6 mg/L. That is, up to 93.5% azophloxine molecules were completely degraded into inorganic compounds. Consequently, potential secondary contamination by intermediate organic products during catalytic degradation was prohibited. The azophloxine removal ratio was kept almost constant after seven cycles, indicating the recyclability and longevity of this system. Furthermore, the azophloxine removal was still promising at high concentrations of Cl-, HCO3-, CO32-. Therefore, our proposed system is potentially effective to remove dye pollutants from seawater. It provides a feasible method for the development of efficient and environmental friendly PMS activation technology combined with FeAlg-ACF, has significant academic and application value.

In the present work, effect of basic components on the energy pathway of ethylene oligomerization by landmark Chevron-Phillips catalyst has been explored in detail using density functional theory (DFT). Studied factors were chosen considering the main components of Chevron-Phillips catalyst, i.e. ligand, cocatalyst and halocarbon compounds, comprising i) the type of alkyl substituents in pyrrole ligand as methyl, iso-propyl, tert-butyl, and phenyl, as well as the simple hydrogen, and the electronwithdrawing fluoro and trifluoromethyl; ii) the number of Cl atoms in Al-compound (as AlMe2Cl, AlMeCl2 and AlCl3) which indicates halocarbon amount and iii) cocatalyst type as alkylboron, alkylaluminium, or alkylgallium. Besides main ingredients, solvent effect, from toluene or methylcyclohexane, on oligomerization pathway was explored as well. In this regard, the full catalytic cycles for the main product (1-hexene) formation as well as side reactions, i.e. 1-butene release and chromacyclononane formation, were calculated on the basis of the metallacycle based mechanism. Based on results, a modification on the Chevron-Phillips catalyst system, to reach higher 1-hexene selectivity and activity, is suggested.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

In this study, the analysis of metals in the solubilized extract of the organic fraction of Urban Solid Waste (MSW) from the municipality of Belém do Pará was carried out. The waste used in this research was collected in residential areas, through door-to-door collection, with the points and neighbor-hoods served in the municipality of Belém determined by the sectorization of these locations, with family income as the main parameter. The MSW was collected and transported to the segregation area. Gravimetric analysis of MSW was carried out and the selected organic and paper fractions were subjected to drying, crushing and sieving pre-treatment. Next, the solubilized extract of the organic fraction of MSW was obtained, following the method set out in NBR nº 10.006/2004 of the Brazilian Association of Technical Standards. The values obtained were compared with CONAMA Resolutions nº 357/2005, 396/2008 and 430/2011, in addition to being compared with results of bibliographical research. The results indicated that these wastes do not comply with environmental and health regulations. Although a highly significant association was found between chromium and boron through Pearson's correlation, the remaining strong correlations between other elements did not reach statistical significance. Furthermore, a similarity was observed in the solubilization conditions of these wastes with those found in landfill leachate.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

Aerobic vaginitis (AV) is a distinct clinical entity characterized by inflammation and abnormal vaginal microflora. Often mistaken for bacterial vaginosis, AV remains relatively unknown and underdiagnosed. AV's understanding is evolving, with some experts suggesting it may primarily be an immunological disorder, the prevalence of which ranges from 7-13% in non-pregnant women and 4.1-8.3% during pregnancy. Pregnancy can affect susceptibility to vaginal infections, leading to adverse outcomes for the woman and the newborn. This review summarizes the correlation between AV and adverse pregnancy outcomes, particularly preterm birth, the leading cause of morbidity and mortality among neonates. Improved understanding of AV's impact on pregnancy outcomes can lead to early recognition, proper management, and effective interventions. While some studies support an association between AV and preterm labor, the existing knowledge of this relationship remains limited. The evidence suggests that AV may contribute to adverse pregnancy outcomes, mainly preterm birth, but further research is needed to establish a definitive link. Further studies are needed to investigate the underlying mechanisms and clarify AV's role in premature labor. A comprehensive understanding of AV's impact on pregnancy outcomes is crucial for early recognition, appropriate management, and effective interventions.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

This research explores the enhancement of bio-oil quality through upgrading with the magnetic bimetallic oxide (CuO-Fe3O4) catalysts supported on the activated rice straw biochar (AcB). These catalysts were employed in a supercritical ethanol-based upgrading process. Various characterization techniques, including elemental analysis, XRD, BET, TGA, and SEM, were utilized to characterize the prepared catalyst. The study revealed significant improvements in the physical characteristics and chemical composition of the bio-oil, with higher heating value (HHV) increasing from 21.3 to 32.1 MJ/kg. Esterification and transesterification were identified as key reactions contributing to this improvement. Notably, the pH of bio-oil increased from 4.3 (raw bio-oil) to 5.63 (after upgrading), signifying reduced acidity. The analysis of the bio-oil's chemical composition highlighted a decrease in oxygen content and an increase in carbon and hydrogen content. At the optimum conditions, the application of supercritical ethanol proved to be an efficient method for enhancing the bio-oil's properties. A crucial transformation occurred during the upgrading process and more than 90% % of carboxylic acids were converted into esters, primarily ethyl acetate at the optimal conditions. This study has demonstrated the effective enhancement of raw bio-oil from rice straw through the utilization of carbon-based bimetallic oxide catalysts in a supercritical upgrading procedure.

Nitrogen oxides (NOx), pivotal atmospheric pollutants, significantly imperil the environment and human health. The CH4-SCR process, leveraging the abundant and accessible methane (CH4), emerges as a promising avenue for NOx abatement. Previous studies have demonstrated that zeolite support with twelve-membered ring (12-MR) and five-membered ring (5-MR) structures are susceptible to framework collapse in the presence of water, leading to catalyst deactivation. Consequently, there is a necessity to explore novel zeolites with enhanced hydrothermal stability for application in CH4-SCR processes. This research introduced for the first time an investigation into a novel In-H-SSZ-39 catalyst, synthesized via ion exchange and meticulously optimized for preparation conditions, including calcination temperature, In ions concentraiton, and reaction conditions, including CH4/NO ratio, O2 concentration, water vapor content, and Gas hourly space velocity (GHSV). Notably, the In/H-SSZ-39 catalyst achieved superior performance of 42.1% at 605 °C, with a calcination temperature of 500 °C and an In ion concentration of 0.066 M, under CH4/NO ratio of 1.5:1, 10% O2, and GHSV of 21000 h-1. In addition, the catalytic performance was influenced by the concentration of water vapor and the GHSV value.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

When water molecules or other particles collide with protein molecules in a solution, the protein molecules absorb some of the momentum and deform, forming a certain molecular potential energy. When a protein molecule in a high-energy state changes to a stable state, if there is a suitable substrate binding and the potential energy of the protein molecule is greater than the energy required to break the substrate chemical bond, catalytic action will occur. The α-helices and β-folds in protein molecules play a major role in converting the kinetic energy of water molecules into their own potential energy due to the large number of amino acids involved and their regular structure. The internal structural deformation of proteins caused by the impact of water molecules on α-helices and β-folds also has a profound impact on the structure of substrates. ‌

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

In this paper, a novel microwave catalyst Ni@SiC/CNFs (NSC), C/Ni (NC), and C/SiC (SC) were successfully synthesized by electrostatic spinning method, and proved to degrade methylene blue with high efficiency under microwave irradiation. The results imply that the catalyst Ni@SiC/CNFs with double shell structure gave a 99.99 % removal rate in 90 s for the degradation of methylene blue under microwave irradiation, outperformed the C/Ni and C/SiC and most other reported catalysts in similar studies. On the one hand, the possible mechanism of the methylene blue degradation should be ascribed to that double shell structure increases the polarization source of the material, resulting in excellent microwave absorption properties; and on the other, the in-situ generation of active species OH• and O2 - under microwave radiation and the synergistic coupling effect of metal plasma greatly improved the degradation efficiency of methylene blue. The findings of this study could provide a valuable reference for the green degradation of industrial dye wastewater and its sustainable development process.

This review paper provides an overview of recent advances in computational fluid dynamics (CFD) simulations of ejector pumps for vacuum generation. It examines various turbulence models, multiphase flow approaches, and numerical techniques employed to capture complex flow phenomena like shock waves, mixing, phase transitions, and heat/mass transfer. Emphasis is placed on comprehensive assessment of flow characteristics within ejectors, including condensation effects such as nucleation, droplet growth, and non-equilibrium conditions. The review highlights efforts in optimizing ejector geometries and operating parameters to enhance the entrainment ratio, a crucial performance metric for ejectors. The studies reviewed encompass diverse working fluids, flow regimes, and geometric configurations, underscoring the significance of ejector technology across various industries. While substantial progress has been made in developing advanced simulation techniques, several challenges persist, including accurate modeling of real gas behavior, phase change kinetics, and coupled heat/mass transfer phenomena. Future research efforts should focus on developing robust multiphase models, implementing advanced turbulence modeling techniques, integrating machine learning based optimization methods, and exploring novel ejector configurations for emerging applications.

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

The superfamily of Acid proteases has two catalytic aspartates for proteolysis of their peptide substrates. Here, we show a minimal structural scaffold, the Structural Catalytic Core (SCC), which packs all conserved substructure elements around the catalytic machinery, and which can be found in all enzymes of the Acid proteases superfamily. The SCC is a dimer of several structural blocks, such as the DD-link, the D-loop and the G-loop, around two catalytic aspartates in each protease subunit or within an individual chain. The dimer of two D-loop/DD-link substructures makes a DD-zone, and the dimer of two D-loop/G-loop substructures makes a psi-loop. These structural markers are useful for protein comparison, structure identification, protein family separation and protein engineering.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physi-cochemical properties and chemical composition of bio-oils, as well as on the morphol-ogy and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subject-ed to the pre-treatments of drying, crushing and sieving. Thermal pyrolysis was per-formed at 400, 450 and 475 °C and 1.0 atmosphere, and catalytic pyrolysis at 450°C and 1.0 atmosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laboratory-scale borosilicate glass reactor. The bio-oil was characterized for acidic val-ue. The chemical functions present in the bio-oil identified by FT-IR and the composi-tion by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW fraction shows bio-oil yields between 9.44 and 9.24% (wt), aqueous phase yields between 21.93 and 18.78% (wt), solid phase yields between 67.97 and 40.34% (wt) and gas yields between 28.27 and 5.92% (wt). The bio-oil yield decreased with in-creasing process temperature. For the experiments using FCC, the biochar and gas yields slightly increased with increasing FCC content, while that of bio-oil decreased and the H2O phase remained constant. GC-MS of bio-oils identified the presence of hy-drocarbons and oxygenates, as well as nitrogen-containing compounds including am-ides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. The presence of hydrocarbons in bio-oil was identified by the addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hydrocarbons.

The main objective of this work is to investigate the temporal variation of PM10 concentrations within the urban area of Athens during the years 2001-2015. For this purpose, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) is recorded for a 15-year period (2001-2015) in two different monitoring stations located in the urban area of Athens. The results show a totally different behavior of PM10 concentrations between the Athens city center and the suburban areas. It seems that in the city center the main sources of PM10 are traffic and heating systems especially during the cold period of the year. Furthermore, in the city center a significant seasonal variation was found with high concentrations during the cold period of the year and lower concentrations during the warm period of the year. Moreover, it was found that during the weekends, there is a decrease in PM10 concentrations probably due to the fact that majority of people do not use their vehicles. Finally, for both locations a significant temporal decreasing trend of the mean annual PM10 concentrations was found which indicates that during the last years, there have been improvements towards a better air quality.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

In terms of obtaining fuels as well as chemicals with or without catalysts at different conditions, the plum seed stands out as an alternative biomass source. Under varying heating rates (10, 50, and 100ºC min-1) and pyrolysis temperatures (400, 450, 500, 550 and 600 °C), the plum seed was pyrolysed at constant sweep gas flow at a constant rate (100 cm3min-1) in a tubular fixed bed reactor. According to the results, an oil yield reaching to a maximum of %45 was procured at the heating rate of 100 ºCmin-1 and the pyrolysis temperature of 550ºC in non-catalytic procedure. The catalytic pyrolysis was carried out in optimum conditions with two selected commercial catalysts, namely ZSM-5 and PURMOL-CTX and clinoptilolite (natural zeolite, NZ) with catalyst ratio of 10 % of raw material. Along with the catalyst addition, the quantity and the quality of bio-oil increased including the calorific value, removal of oxygenated groups, and hydrocarbon distribution. An increase related to the desirable products like phenols, alkene, and alkane and a decrease in undesirable products like acids were observed in the presence of catalysts. When all the results are considered and evaluated, using zeolite materials in the pyrolysis as catalysts is a recommendable option to achieve enhanced chemicals and fuels.

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

In this review we explore the recent progress in catalytic materials for ammonia synthesis that are based on metal nitrides and other catalytic surfaces. It comprises a detailed overlook of various techniques used in ammonia synthesis research and the state-of-the-art modeling techniques employed to investigate new reaction mechanisms and more efficient processes for sustainable ammonia synthesis production. The review is discussed in the context of reaction mechanisms developed and recent progress that has been made with respect to thermal, electrochemical and photocatalytic ammonia synthesis.

Acacia dealbata Link, named Mimosa in Portugal, is an invasive hardwood species with potential for construction use, but research is limited. The available stock of small-diameter juvenile wood (sjw) logs can help reduce this gap, but tangential cracking at log ends challenges fastener connections. This study evaluated different treatments to control and reduce end-face cracking in sjw logs during air drying, an economical and environmentally friendly procedure. Extreme two-thirds of sixteen Mimosa logs were subjected to two treatments: one with longitudinal kerfs 15 mm deep along the length (2 and 3 kerfs) and the other with a hollow in the centre up to half the length (16 mm and 30 mm diameters). Over 219 days of air drying and compared with the central part, kerfing treatments significantly reduced outer wood tangential cracking (p < 0.001), with the 3-kerf also reducing crack numbers (p < 0.05) but increasing significantly cracks near the pith (p < 0.01). The 30 mm central hollow significantly reduced central perforation cracking (p < 0.05). Results suggest that a combined treatment approach could help mitigate cracking, enhancing the suitability of wild Mimosa logs for construction use.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

We will apply Pascal’s hydrostatic pressure law to black holes and also to the Hubble sphere. Haug has recently demonstrated how hydrostatic pressure in water can be utilized to determine the Planck length. One can conceptualize the energy in the Hubble sphere as a type of superfluid, and if this is correct, then Blaise Pascal’s hydrostatic pressure formula may also be applicable to such a superfluid, even within the Hubble sphere. By employing the same method on the Hubble sphere and considering it as a Schwarzschild black hole with the critical Friedmann mass, we can estimate the Planck length based on its hypothetical hydrostatic pressure.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

L-gulonolactone oxidase enzyme (GULO) catalyzes the last step of L-ascorbic acid (vitamin C) biosynthesis. This enzymatic activity is lost in primates. The full-length rat GULO has been previously produced in plants and demonstrated to be active. In this study, we compare activity of two variants of GULO produced in Escheriachia coli cells, full-length rat GULO (fGULO) and its C-terminal catalytic domain (cGULO). The expression and purification of the recombinant proteins were optimised and their biological activity was confirmed by two methods, the GULO activity assay in the protein extracts and the ‘in-gel’ staining for GULO activity. Both variants of recombinant GULO were biologically active in both assays. However, cGULO is more promising than fGULO for ascorbic acid production because it is more efficiently produced by bacteria.

Introduction: The balance of bioelements is crucial as it ensures the organism's homeostasis and proper execution of reactions within the body, nerve conductivity, and correct polarity of cell membranes, but it is also very important for fertility. It is known that disturbances in the balance of bioelements lead to reproductive dysfunction. In women, changes in the composition of follicular fluid can occur, which can lead to limited follicular growth and lack of oocyte activation. Objective: The main objective was to examine whether the concentration of bioelements Na, K, Ca, Mg, and Fe in follicular fluid influences the outcome of the in vitro fertilization process. Methods: The study involved 120 female patients undergoing in vitro fertilization. Follicular fluid obtained after follicle aspiration in the ovaries was used as biological material for analysis. The values of Na (selective electrode method), K (selective electrode method), Ca (arenajo method), Mg (spectrophotometric method), and Fe (colorimetric method) in follicular fluid were determined using the AU 680 apparatus, Beckman Coulter. Istanbul Consensus criteria for clinical embryologists were used to assess embryo quality. Statistical analysis was performed using the SPSS 20 software package. Results: Analysis of follicular fluid samples showed no correlation between the concentration of bioelements in follicular fluid and the quality of oocytes or the outcome of in vitro fertilization. Conclusion: Based on our results, it can be concluded that the concentration of bioelements in follicular fluid does not affect the outcome of in vitro fertilization.

K417G Ni-based superalloy is widely used in aeroengine turbine blade for its excellent properties. However, the aeroengine rotor blade zigzag crown appears early failure frequently, which is because of the wear problems occurring in the working process. Laser forming repairing (LFR) is a promising technique to repair these damaged blades. Unfortunately, the laser formed Ni-based superalloys with high content of (Al + Ti) have a high cracking sensitivity. In this paper, the crack characterization of the LFRed K417G, the microstructure, microhardness and tribological properties of the coating before and after laser remelting are presented. The results show that the microstructure of as-deposited K417G consists of γ phase, γ′ precipitated phase, γ + γ′ eutectic and carbide. Cracking mechanisms including solidification cracking, liquation cracking and ductility dip cracking are proposed based on the composition of K417G and processing characteristics to explain the cracking behavior of the K417G superalloy during LFR. After laser remelting, the microstructure of the coating has been refined, and the microhardness and tribological properties has been improved. Laser remelting can decrease the size of the cracks in the LFRed K417G but not the number. Therefore, laser remelting can be applied as an effective method for strengthening coating and as an auxiliary method for controlling cracking.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Ensuring access to water, sanitation, and hygiene (WASH) facilities, coupled with behavior change education in schools, is fundamental for fostering a conducive learning environment and promoting principles of inclusion, dignity, and equality. This study focuses on 12 primary schools in Anápolis, Brazil, encompassing 4,394 students and 248 teachers. WASH assessments were conducted through a questionnaire, observation of water and sanitation facilities and structures, and microbiological analysis. Over the period 2018 to 2020, the proportion of schools with safely managed drinking water surged from 42% to 92%. However, sanitation conditions in the schools were categorized as a basic level, with hygiene services rated as limited in 92% of the schools due to the absence of soap. While this study reveals that Anápolis schools generally align with WASH guidelines for basic/advanced drinking water services, there is a crucial need for enhancements in both hardware and software facilities to address sanitation and hygiene challenges.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

Hydrogen and carbon monoxide over-equilibria have been found computationally in kinetic dependencies of methane reforming catalytic reactions (steam and dry reforming) using conditions of the conservatively perturbed equilibrium (CPE) phenomenon, i.e. at the initial equilibrium concentration of hydrogen or carbon monoxide.  The influence of pressure, temperature, flow rate and composition of the initial mixture on the position of the CPE point (the extremum point) was investigated in a wide domain of parameters. It is demonstrated that the CPE phenomenon significantly increases the product concentration (H2 and CO) at the reactor length which is significantly less than the reactor length required to reach the equilibrium. The CPE-point was interpreted as the “turning point” in kinetic behavior.  Recommendations on the temperature and pressure regimes are different from the traditional ones related to the Le Chatelier’s law. Obtained results provide valuable information on optimal reaction conditions for complex reversible chemical transformations, offering potential applications in chemical engineering processes.

“Clickase” single-chain nanoparticles (Ck-SCNPs) are folded, enzyme-mimetic unimolecular polymeric nano-objects containing copper (Cu) ions able to catalyze the azide-alkyne Huisgen cycloaddition reaction in water and/or selected organic solvents, often in the presence of a reductant. Herein, we investigate the effect of morphology on catalytic activity of Ck-SCNPs synthesized by means of two different routes. An amphiphilic random copolymer composed of oligo(ethylene glycol) methyl ether methyl methacrylate (OEGMA) and 2-acetoacetoxy ethyl methacrylate (AEMA) units was used as precursor of these Ck-SCNPs. Folding was promoted through metal complexation between Cu(II) ions and beta-ketoester-containing AEMA moieties. The first route resulted in Ck-SCNPs1 containing Cu ions homogeneously distributed within each nanoparticle, whereas the second one promoted intra-chain clustering of Cu ions inside Ck-SCNPs2. A model fluorogenic “click” reaction between 9-(azidomethyl)anthracene and phenylacetylene, which was catalyzed either by Ck-SCNPs1 or Ck-SCNPs2, was used to unravel the effect of morphology on catalytic activity. This work paves the way to improve the catalytic activity of metallo-folded SCNPs through control of the intra-chain distribution of catalytic sites.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Data leakage by statistical officers represents a significant statistical crime under the Indonesian Statistics Law. However, despite the legal provisions, there has been a notable absence of enforcement actions against such breaches, raising questions about the effectiveness and applicability of the current legal framework for addressing statistical crimes related to data leakage. This study identifies a research gap in the enforcement and operationalization of existing laws, emphasizing the lack of empirical data on how these legal provisions are applied in practice. Utilizing an empirical research methodology, this study analyzes data and real-world instances of statistical data leakage. The findings reveal that unethical behavior among statistical officers, inadequate data security measures, and the threat of social engineering significantly contribute to the potential for data breaches. The study's strength lies in its focus on providing a comprehensive understanding of these issues and proposing actionable solutions. This research not only fills the existing gap by offering empirical insights but also advances practical recommendations for enhancing data protection and legal enforcement mechanisms within Indonesia’s statistical framework.

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

We present some exact analytical solutions describing, either the evolution of fluid distributions corresponding to a ghost star (vanishing total mass), or describing the evolution of fluid distributions which attain the ghost star status at some point of their lives. The first two solutions correspond to the former case, they admit a conformal Killing vector (CKV) and describe the adiabatic evolution of a ghost star. Other two solutions corresponding to the latter case are found, which describe evolving fluid sphere absorbing energy from the outside, leading to a vanishing total mass at some point of their evolution. In this case the fluid is assumed to be expansion–free. In all four solutions the condition of vanishing complexity factor was imposed. A discussion of the physical implications of the results, is presented.

The article considers the role of transcrustal magma- and fluid-conducting faults in the formation of mineral deposits, shows the importance of a deep source of heat and hydrothermal solutions in the genesis and history of the formation of these deposits. As a result of the impact on the lithosphere of mantle jets rising along transcrustal faults, intense block-and-clump deformations and tectonic movements are generated; rift systems and volcanic-plutonic belts spatially combined with them are formed; intrusive bodies are introduced. At ore deposits, these processes cause epithermal ore formation as a consequence of the impact of mantle jets rising along transcrustal faults on the lithosphere. At hydrocarbon fields, they play an extremely important role in conduction and convective heat and mass transfer to the area of hydrocarbon generation, determine the relationship between the processes of lithogenesis and tectogenesis, and activate the generation of hydrocarbons from oil and gas mother formations. Detection of transcrustal magma- and fluid-supporting faults was carried out by MMZ and MTZ in combination with other geological and geophysical data. Practical examples are given for mineral deposits under which subvertical transcrustal columns of increased permeability traced to considerable depths have been found. The nature of these unique structures is related to faults of pre-Paleozoic time of emplacement, which determined the fragmentation of the subcrystalline structure of the Earth and later developed inherited in the conditions of development of volumetric fluid dynamics. The residual forms of functioning of fluid-conducting thermohydrocolumns are granitoid batholiths and other magmatic bodies. Experimental modelling of deep processes allowed to reveal the quantum character of interactions of crystal structures of minerals with "inert" gases under elevated T-P conditions. The role of helium, nitrogen and hydrogen in changing the physical properties of rocks in connection with their intrastructural diffusion has been clarified. As a result of low-energy impact, stress fields are formed in the solid rock skeleton, the structure and texture of rocks are rearranged, and general porosity develops. With increasing pressure, energy interactions intensify, deformations, phase transitions and chemical bonds occur in an unstable geological environment, which increases with increasing gas saturation, pressure, and temperature. The process of heat and mass transfer along transcrustal magma- and fluid-supplying faults to the Earth's surface occurs in stages with energy release, which can manifest itself in the form of explosions on the day surface, in coal and ore mines, in earthquakes and volcanic eruptions.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

The current work reveals the fine tuning between stability zones and randomness of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing D/M/1 system. More specifically, this clearly provides more insights into developing a contemporary PSFFA theory that unifies non-stationary queueing theory with chaos theory and fields in both theoretical physics and chaotic systems. This opens new grounds for stability analysis of non-stationary queueing systems.

Fly ash cement has rarely been used in Japan, mainly because its strength development is slower than ordinary Portland cement. In this research, the effect of the new fly ash cement with both high alite (C3S) cement and fly ash modified by electrostatic belt separation method on cracking resistance of precast concrete prepared by steam curing was studied. The mechanical and shrinkage properties of the proposed fly ash concrete were compared with those of concrete made using OPC cement without fly ash. In order to study the cracking tendency of precast concrete with the proposed fly ash cement, thermal stress analysis was conducted taking into consideration of the experimental data of concrete properties with the different concrete mix proportions. A standard precast concrete box culvert model was used in this 3D FEM analysis and the distribution of temperature and relative humidity in cross section and induced restraint stress during and after steam curing were discussed. Steam-cured concrete with fly ash and high alite cement developed higher compressive strength on the first day of age than concrete with OPC. The proposed fly ash concrete developed high cracking resistance in the early days. On the other hand, the results showed that the drying shrinkage at later ages was the main cause of cracking.

The impact of COVID-19’s unexpected outbreak forced the scientific world to thoroughly seek alternative ways of treatment in order to overcome the hindrance of traditional medicine in alleviating the symptoms of this virus and possibly be an option for a potential cure in the near future. The antibiotic erythromycin, which was introduced in 1952, has been reported to pose an effective substitute medication for various ailments such as skin, respiratory, bone, female reproductive conditions, and cancer, as well as the newly added COVID-19’s aftermath. Countries, World Health Organization and the health industry have recruited and cooperated with numerous universities and institutions, so as to tackle the demand for efficient antibiotics, with USA and China leading this effort. Consequently, the catalytic mechanism of erythromycin’s synthesis and industrial production was discussed and analyzed further in order to gain a better understanding and extrapolate innovative and environmentally friendly methods of producing this antibiotic. Therefore, the demand for an increase and improvement in the production of erythromycin should be globally promoted, in order to deliver more effective results against infectious diseases such as COVID – 19.

Background: Diagnostic accuracy of Parkinson’s disease (PD), a synucleinopathy, based on diagnostic criteria is suboptimal. A biomarker for synucleinopathies is pivotal both from a clinical and from a research aspect. CSF a-synuclein has been extensively studied over the past two decades as a candidate biomarker of synucleinopathies. Herein we present data on studies focusing on total, phosphorylated and oligomeric CSF a-synuclein in PD. Methods: Pubmed, Scopus and Web of Science were searched for studies with >10 PD patients and control subjects, with data (mean, SD) on total, phosphorylated or oligomeric a-synuclein. Cohen’s d, as a measure of effect size, was calculated for all a-synuclein forms. Subgroup analysis and meta-regression were performed in an effort to explain between-study heterogeneity. Results: Thirty studies on total, six studies on oligomeric and one study on phosphorylated a-synuclein were included. Total a-synuclein was decreased and oligomeric a-synuclein increased in PD patients vs. controls. Effect size was medium for total and high for oligomeric a-synuclein. A-syn forms provided suboptimal combined sensitivity/specificity for the differentiation of PD from controls. There was significant between-study heterogeneity. PD cohort characteristics (sex, age, disease duration, UPDRS, H&Y) and study characteristics (study design, healthy vs. neurological controls, control for CSF blood contamination, method of a-syn measurement) could not account for between-study heterogeneity. Publication bias was limited. Conclusions: CSF a-synuclein levels lack sufficient accuracy to be used as biomarkers for PD. Standardization of (pre)analytical variables may improve the discriminatory power of a-synuclein forms in the future.

Recently, microfluidics deformability cytometry has emerged as a powerful tool for high throughput mechanical phenotyping of large populations of cells. These methods characterize cells by their mechanical fingerprints through exerting hydrodynamic forces and monitoring the resulting deformation. These devices have shown great promise for label free cytometry, yet there is a critical need to improve their accuracy and reconcile any discrepancies with other methods, such as atomic force microscopy. In this study, we employ computational fluid dynamics simulations and uncover how the elasticity of frequently used carrier fluids such as methyl-cellulose dissolved in phosphate-buffered saline is significantly influential to the resulting cellular deformation. We conducted CFD simulations that are conventionally used within the deformability cytometry field, which neglect fluid elasticity. Subsequently, we incorporated a more comprehensive model that simulates the viscoelastic nature of the carrier fluid. A comparison of the predicted stresses between these two approaches underscores the significance of the emerging elastic stresses in addition to the well-recognized viscous stresses along the channel. Furthermore, we utilize a two-phase flow model to predict the deformation of a promyelocyte (i.e. HL-60 cell type) within a hydrodynamic constriction channel. The obtained results highlight a substantial impact of the elasticity of carrier fluid on cellular deformation and raise questions about the accuracy of mechanical property estimates derived by neglecting elastic stresses.

The present review paper aims at collecting and discussing the research work, numerical and experimental, carried out in the field of Fluid-Structure Interaction (FSI) in one-dimensional (1D) pressurized transient flow in the time-domain approach. Background theory and basic definitions are provided for the proper understanding of the assessed literature. A novel frame of reference is proposed for the classification of FSI models based on pipe degrees-of-freedom. Numerical research is organized according to this classification, while an extensive review on experimental research is presented by institution. Engineering applications of FSI models are described and historical accidents and post-accident analyses documented.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Deep eutectic solvents are a mixture of two or more components, that at a particular composition become liquids at room temperature. When the compounds that constitute the DES are primary metabolites, namely, amino acids, organic acids, sugars, or choline derivatives, the DES are so called natural deep eutectic solvents (NADES). NADES fully represent green chemistry principles. These solvents are highly welcome, as they are obtained from renewable resources, and gratifyingly biodegradable and biocompatible. They are an alternative to room temperature ionic liquids (RTILs). From the pharmaceutical industry point of view, they are highly desirable, but unfortunately have been rarely used despite their enormous potential. In this review, we will look at their impact on the asymmetric catalytic synthesis of key target molecules, via metal-based catalysis, biocatalysis and organocatalysis. In many cases the NADES that have been used are chiral and can even promote enantioselective reactions, this crucial and very exciting aspect will also be discussed and analysed.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

In recent years, the emergence of cancer drug resistance is one of the crucial tumor hallmarks which is supported by the level of genetic heterogeneity and complexities at cellular levels. Oxidative stress, immune evasion, metabolic reprogramming, overexpression of ABC transporters and stemness are among the several key contributing molecular and cellular response mechanisms. Topo-active drugs, e.g., doxorubicin and topotecan, are clinically active and are utilized extensively against a wide variety of human tumors and often results in the development of resistance and failure to therapy. Thus, there is an urgent need for an incremental and comprehensive understanding of mechanisms of cancer drug resistance specifically in the context of topo-active drugs. This review delves into the intricate mechanistic aspects of these intracellular and extracellular topo-active drug resistance mechanisms and explores use of potential combinatorial approaches by utilizing various topo-active drugs and inhibitors of pathways involved in drug resistance. We believe that this review will help guide basic scientists, pre-clinicians, clinicians, and policymakers toward holistic and interdisciplinary strategies that transcend resistance, renewing optimism in the ongoing battle against cancer.

3,4-Dihydroquinolin-2(1H)-ones represent a class of valuable bioactive compounds with six-membered nitrogen-containing heterocyclic structures. The development of simple, mild and efficient synthetic methods has been widely concerned by synthetic chemists. In this review, we have summarized a series of different synthetic strategies for the synthesis of dihydroquinoline-2(1H)-ones via catalytic annulation of α,β-unsaturated N-arylamides in the past decade, including covering electrophilic cyclization, radical initiated cyclization and photochemical cyclization reactions. Besides, the substrate scope and mechanistic details are also discussed. This paper will provide a useful reference for the development of diverse synthesis methodologies of 3,4-dihydroquinolin-2(1H)-ones.

Nickel molybdate, NiMoO₄, nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using UV-Vis absorption.

In this paper we develop from first principles a unique law pertaining to the flow of fluids through closed conduits. This law, which we call “Quinn’s Law”, may be described as follows: When fluids are forced to flow through closed conduits under the driving force of a pressure gradient, there is a linear relationship between the normalized dimensionless pressure gradient, P_Q, and the normalized dimensionless fluid current, C_Q. The relationship is expressed mathematically as: P_Q = k₁ +k₂C_Q. This linear relationship remains the same whether the conduit is filled with or devoid of solid obstacles. The law differentiates, however, between a packed and an empty conduit by virtue of the tortuosity of the fluid path, which is seamlessly accommodated within the normalization framework of the law itself. When movement of the fluid is very close to being at rest, i.e., very slow, this relationship has the unique minimum constant value of k₁, and as the fluid acceleration increases, it varies with a slope of k₂ as a function of normalized fluid current. Quinn’s Law is validated herein by applying it to the data from published classical studies of measured permeability in both packed and empty conduits, as well as to the data generated by home grown experiments performed in the author’s own laboratory.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

Finite element discretizations of problems in computational physics often rely on hand-generated initial mesh and adaptive mesh refinement (AMR) to preferentially resolve regions containing important features during simulation. We propose Adaptnet, a Graph Neural Networks (GNNs) framework for learning mesh generation and adaptation. The model is composed of two GNNs: the first one, Meshnet, learns mesh parameters commonly used in open-source mesh generators, to generate an initial mesh from a Computer Aid Design (CAD) file; while the second one, Graphnet, learns mesh-based simulations to predict the components of an Hessian-based metric to perform anisotropic mesh adaptation. Our approach is tested on structural (Deforming plate - Linear elasticity) and fluid mechanics (Flow around cylinders - steady-state Stokes) problems. Our results show it can accurately predict the dynamics of the system and adapt the mesh accordingly. The adaptivity of the model supports learning resolution-independent dynamics and can scale to more complex state spaces at test time.

Polyphenols are well-known health promoting agents, but they have some limitations due to their spontaneous oxidation. This evidence has limited their use as drugs in the last years. In this field, several chemical modifications have been proposed to overcome these restrictions; among these, the esterification seems to be the preferred. Ester derivatives could be able to reduce the bioavailability problems connected to polyphenols. On the other hand, the presence of the esterase enzymes in the body guarantees the ester hydrolysis, which in turn frees the two molecules that make it up. Lipase-catalyzed esterifications afforded several derivatives of flavonoids glycosides, in green conditions. In this short note, pancreatic porcine lipase was firstly used as a cheap bio-catalyst, to synthesize oleoyl derivatives of quercetin in aglycone form. Results demonstrated how the enzyme acyl regioselective in position C-3, with high yields and easy purification processes

This study proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopted a membrane reactor operated due to the non-equilibrium state with H2 separation from the reaction space. This study aimed to clarify the characteristics of Ni/Cr/Ru catalyst using for a biogas dry reforming membrane reactor. Additionally, this study also investigated the comparison of the characteristics of Ni/Cr/Ru catalyst with that of Ni/Cr catalyst. The impact of operation temperature, the molar ratio of CH4 : CO2, the differential pressure between the reaction chamber and the sweep chamber and the introduction of sweep gas on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr/Ru catalyst was examined. The concentration of H2 using Ni/Cr/Ru catalyst was larger than that using Ni/Cr catalyst by 2871 ppmV for the molar ratio of CH4 : CO2 = 1.5 : 1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa without a sweep gas, especially. Under this condition, CH4 conversion, H2 yield and thermal efficiency were 67.4 %, 1.77×10-2 % and 0.241 %, respectively.

The paper presents a new type of hydraulic clutch operating with magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. The hy-draulic clutch system of its own design with MR working fluid and a rotating magnetic field lo-cated is designed. The principle of this clutch is to use a rotating magnetic field created by an al-ternating current electromagnet to set the MR fluid in motion. In the tests of the hydraulic clutch with a rotating magnetic field, MR fluid produced on their own, consisting of solid iron particles of various diameters mixed with a silicone oil, are used as working fluids. The rheological properties of MR fluids are assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating the magnetic field of its own design. The char-acteristics of the hydraulic clutch with MR working fluid and the rotating magnetic field are tested on a specially built test stand. As a result of the research, it has been found that the torque transmitted by the clutch is the greater, the higher the rotational speed of the magnetic field and the lower the rotational speed of the beaker in which the working fluid is placed, and that the greatest torque occurs for the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch working with MR fluid and the rotating magnetic field can be applied to stationary power transmission system similarly to an eddy current clutch.

We report the development of an extrinsic self-healing coating system that shows no fluorescence from the intact coating, yellowish fluorescence in cracked regions, and greenish fluorescence in healed regions, thus allowing the separate monitoring of cracking and healing of coatings. This fluorescence monitoring self-healing system consisted of a top coating, an epoxy matrix resin containing mixed dye-loaded in single microcapsule. The dye-loaded microcapsules consisted of a poly(urea-formaldehyde) shell encapsulating a healing agent containing MAT-PDMS and styrene, a photo-initiator and a mixture of two dyes, one that fluoresces only in the solid state (DCM) and a second that fluoresces dramatically increased in the solid than solution state (4-TPAE). A mixture of the healing agent, photo-initiator and the two dyes was yellow due to fluorescence from DCM. On UV curing of this mixture, however, the color changed from yellow to green and the fluorescence intensity increased due to fluorescence from 4-TPAE in the solid state. When a self-healing coating embedded with microcapsules containing the DCM/4-TPAE dye mixture was scratched, the damaged region exhibited a yellowish color that changed to green after healing. Thus, the self-healing system reported here allows the separate monitoring of cracking and healing based on changes in fluorescence color.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

This study investigates the stress corrosion cracking (SCC) behavior of type 316L stainless steel (SS316L) produced with sinter-based material extrusion additive manufacturing (AM). This technology has been shown to produce SS316L with microstructures and mechanical properties comparable to its wrought counterpart in the annealed condition. However, despite plenty of research on SCC of SS316L, little is known about SCC in sinter-based AM SS316L. This study focuses on the influence of sintered microstructures on susceptibility to SCC initiation and crack-branching. Custom-made C-rings were exposed to different stress levels in acidic chloride solutions at various temperatures. To better understand the SCC behavior of SS316L, solution-annealed (SA) and cold-drawn (CD) wrought SS316L were tested for comparison. Results showed that sinter-based AM SS316L was more susceptible to SCC initiation than SA wrought SS316L but more resistant than CD wrought SS316L. Moreover, sinter-based AM SS316L showed noticeably better resistance to crack-branching than both wrought SS316L counterparts. The investigation was supported by comprehensive pre- and post-test microanalysis using light optical microscopy (LOM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and micro-computed tomography (micro-CT)

In this work, the recently proposed cracking elements method (CEM) is used for simulating the damaging processes of structures with initial imperfections. CEM is built in the framework of conventional FEM which is formally like a special type of finite element. The disconnected piecewise cracks are used for representing crack paths. Taking the advantages of CEM that both the initiations and propagations of cracks can be naturally captured, we numerically study the uni-axial compression tests of specimens with multiple joints and fissures, where the cracks may propagate from the tips, or from some other unexpected positions. Though uni-axial compression tests are considered, mainly tensile damage criteria are used in the numerical model. On one hand, the results demonstrate the robustness and effectiveness of the CEM while on the other hand, some drawbacks of the present model are demonstrated, showing the future work.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

The purpose of this study is to investigate the perceived benefits of community gardening. A garden colony is a collection of adjacent plots of land primarily for the purpose of gardening. The methodology of this research consists of observations, interviews, questionnaires, and focus group. As a result of this research we found that gardening is a natural and safe way to meet the lifelong demands for a healthy life. We found specific mental and physical benefits as a result of this community gardening. We encourage communities to allow people to buy plots of land away from their homes to promote this healthy activity. The garden colony provides a place for individual renewal and restoration; this urban oasis offers a way to maintain and promote lifelong healthy living, and they are an important contribution to one’s life by adding a sense of meaning and purpose.

Recent trends concerning hydrogen as a fuel of the future and problems related to its production, storage and utilization increase the demand for efficient technologies related to these problems. A large part of such technologies is related to application of advanced materials based on various complex oxides which are used as efficient catalysts for fuel transformation into hydrogen and syngas, materials for membranes with selective permeability for hydrogen and syngas production, components of solid oxide fuel cells/electrolyzers as well as many other applications in energy, electrochemistry and catalysis. Such materials are typically based on oxides and solid solutions with perovskite and fluorite structures or their derivatives. Attention is also paid to the materials based on spinel, apatite, mayenite, sheelite, fergusonite structures. The above-mentioned materials are continuously studied in order to modify and optimize their functional properties. On the other hand, other classes of materials (weberites, monazites, etc.) are recently discovered and considered as candidate materials for the aforementioned applications due to their specific functional properties or a great potential of their improvement. In this review, some of these materials are considered.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Compared to the southern Tibetan Plateau, the northern part has been regarded as relatively lacking geothermal resources. However, there is no lack of natural hot springs exposed in beads along large-scale fracture systems, and research on them is currently limited to individual hot springs or geothermal systems. This paper focuses on the Wahongshan-Wenquan Fracture Zone (WWFZ), analyzes the formation of five hydrothermal activity zones along the fracture zone in terms of differences in the hydrochemical and isotopic composition of the hot water, and then explores the hydrothermal control of hot springs in the zone by the fracture. The results show that the main Fractures of WWFZ is the regional heat-control structures, and the fracture system formed by a small number of near-north-south and near-east-west fractures transversal to it provides a favorable channel for deep hydrothermal convective circulation. Ice and snow melt water from the Ngola Shan Mountains, with an average elevation of more than 4,500 meters above sea level, infiltrates along the fractures and is heated by deep circulation to form deep geothermal reservoirs. There is no detectable contribution of mantle source heat to the hot spring gases, and the heat source is mainly natural heat conduction warming, but the "Low-Velocity body (LVB)" in the middle and lower crust of the area may be the primary heat source of the high geothermal background in the area. The hydrochemical components of the hot springs in the area show a certain regularity, and the main ionic components, TDS and water temperature, tend to increase away from the main rupture, reflecting the controlling effect of the WWF on the hydrothermal transport in the area. In the future, the geothermal work in this area should focus on the hydrothermal control properties of different levels, the nature of fractures in the area, and the thermal contribution of LVB in the middle and lower crust.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

MoS2 has long been considered as a promising catalyst for hydrogen production. At present, there are many strategies to further improve its catalytic performance, such as edge engineering, defect engineering, phase engineering and so on. However, at present, there is still a great deal of controversy about the mechanism of MoS2 catalytic hydrogen production. For example, it is generally believed that the base plane of MoS2 is inert, but it has been reported that the inert base plane can undergo a transient phase transition in the catalytic process to play the catalytic role, which is contrary to the common understanding that the catalytic activity is only at the edge. Therefore, it is necessary to further understand the mechanism of MoS2 catalytic hydrogen production. In this article, we summarized the latest research progress on the catalytic hydrogen production of MoS2, which is of great significance for revisited the mechanism of MoS2 catalytic hydrogen production.

This short review is aimed at giving an overview of catalytic carbonylative double cyclization reactions, which are processes in which suitable organic substrates and carbon monoxide are sequentially activated by a promoting catalyst to afford the formation of two new cycles with concomitant incorporation of carbon monoxide as a carbonyl function into the final product. Paradigmatic examples of this powerful synthetic methodology, which allows the one-step synthesis of complex molecular architectures from simple building blocks using the simplest and readily available C-1 unit (CO) are illustrated and discussed. The review is divided into five sections: 1) Introduction; 2) Functionalized Olefinic Substrates; 3) Functionalized Acetylenic Substrates; 4) Functionalized Halides; 5) Conclusions and Future Perspectives.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

Some global difficulties in the modern period include energy storage conversion. Researchers have looked to renewable energy resources to discover long-term answers to this dilemma. Fuel cells are one example of prospective energy producing technology. Although these technologies appear to be very enticing, they are known to be expensive due to high expenses. Catalyst costs, as well as concerns concerning energy density. Pt based Electrocatalysts have traditionally been used to drive ORR and offer efficient power outputs. However, cost constraints have limited the use of these electrocatalysts, rendering them inefficient. Apart from the high price, Pt-based Electrodes are prone to time-dependent drift and CO deactivation, both of which occur gradually. Electrocatalysts deteriorate over time, reducing the efficiency of fuel cells. This is why alternative electrocatalysts are in high demand for future energy applications. This review covers the comparative study of Platinium and Non-Platinium based electrocatalyst in fuel cells, their shortcomings and recent advancement for efficient and optimized electrocatalyst.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.