In this contribution, different lane-keeping control strategies for Autonomous Ground Vehicles (AGV) have been analyzed and compared. The AGV must be oriented and kept within a given reference path using the front wheel steering angle as the control action for a specific longitudinal velocity. While non-linear models can describe the lateral dynamics of the vehicle in an accurate manner, they might lead to difficulties when computing some real-time control laws such as Model Predictive Control (MPC). Linear Parameter Varying (LPV) models can provide a trade-off between computational complexity and model accuracy. Another way to reduce computational complexity is to explore other control strategies, for example, the one based on the Inverse Kinematic Bicycle model (IKIBI). Additionally, AGV sensors typically work at different measurement acquisition frequencies so that Kalman Filters (KF) are usually needed for sensor fusion. If these frequencies are slower than the actuation rate, a multi-rate KF may be needed. The two control strategies (MPC using a LPV model and IKIBI) have been compared in simulations over a circuit path in the presence of process and measurement Gaussian noise. The MPC controller has shown to provide a more accurate lane-keeping behavior than an IKIBI control strategy. Finally, it has been seen that Dual-Rate Extended Kalman Filters (DREKF) constitute an essential tool when only slow and noisy sensor feedback is available in an AGV lane-keeping application.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

First, a recently developed eigenfunction expansion technique, based in part on separation of the thickness-variable and partly utilizing a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism, is employed to derive three-dimensional singular stress fields in the vicinity of the front of an interfacial crack weakening an infinite bicrystalline superlattice plate, made of orthorhombic (cubic, hexagonal and tetragonal serving as special cases) phases, of finite thickness and subjected to the far-field extension/bending, in-plane shear/twisting and anti-plane shear loadings, distributed through the thickness. Crack-face boundary and interface contact conditions as well as those that are prescribed on the top and bottom surfaces of the bicrystalline superlattice plate are exactly satisfied. It also extends a recently developed concept of lattice crack deflection (LCD) barrier to a superlattice, christened superlattice crack deflection (SCD) energy barrier for studying interfacial crack path instability, which can explain crack deflection from a difficult interface to an easier neighboring cleavage system. Additionally, the relationships of the nature (easy/easy, easy/difficult or difficult/difficult) interfacial cleavage systems based on the present solutions with the structural chemistry aspects of the component phases (such as orthorhombic, tetragonal, hexagonal as well as FCC (face centered cubic) transition metals and perovskites) of the superlattice are also investigated. Finally, results pertaining to the through-thickness variations of mode I/II/III stress intensity factors and energy release rates for symmetric hyperbolic sine distributed load and their skew-symmetric counterparts that also satisfy the boundary conditions on the top and bottom surfaces of the bicrystalline superlattice plate under investigation, also form an important part of the present investigation.

A newly synthesized upper rim azocalix[4]arene, namely, 5,11,17,23-tetra[(4-ethylacetoxyphenyl) (azo)]calix[4]arene, CA-AZ was fully characterized and its chromogenic and selective properties for anions are reported. The receptor is selective for the fluoride anion and its mode of interaction in solution is discussed. The kinetics of the complexation process was found to be very fast as reflected in the immediate color change observed with a naked eye resulting from the receptor-anion interaction. Emphasis is made about the relevance in selecting a solvent in which the formulation of the process is representative of the events taking place in the solution. The composition of the fluoride complex investigated by UV/VIS spectrophotometry, conductance measurements and titration calorimetry was 1:1 and the thermodynamics of complexation was determined. The fluoride complex salt was isolated, and a detailed investigation was carried out to assess its ability to remove CO₂ from the air. Recycling of the complex was easily achieved. Final conclusions are given.

The efficient generation of high-quality random numbers is essential in the operation of cryptographic modules. The quality of a random number generator is evaluated by the min-entropy of its entropy source. Typical method used to achieve high min-entropy of the output sequence is an entropy accumulation based on a hash function. This is grounded in the famous Leftover Hash Lemma which guarantees a lower bound on the min-entropy of the output sequence. However, the hash function based entropy accumulation has slow speed in general. For a practical perspective we need a new efficient entropy accumulation with the theoretical background for the min-entropy of the output sequence. In this work, we obtain the theoretical bound for the min-entropy of the output random sequence through the very efficient entropy accumulation using only bitwise XOR operations, where the input sequences from the entropy source are independent. Moreover we examine our theoretical results by applying to the quantum random number generator that uses dark noise arising from image sensor pixels as its entropy source.

This study explored the feasibility of fluoride removal from simulated semiconductor industry wastewater and its recovery as calcium fluoride using fluidized bed crystallization. The continuous reactor showed best performance (>90% fluoride removal and >95% crystallization efficiency) at a calcium to fluoride ratio of 0.6 within first 40 days of continuous operation. The resulting particle size increased by more than double during this time along with a 36% increase in the seed bed height indicating deposition of CaF2 onto the silica seed. The SEM-EDX analysis showed the size and shape of the crystals formed along with high amount of Ca-F ions presence. The purity of the CaF2 crystals were determined to be 91.1% though ICP-OES analysis. Following the continuous experiment, different process improvement strategies are explored. The addition of excess amount of calcium resulted in an additional 6% fluoride removal, however, compared to this single stage process, a two-stage approach was found to be better strategy to achieve a low effluent fluoride concentration. The fluoride removal reached 94% with this two-stage approach under optimum condition of 4 + 1 h HRT combinations and a [Ca2+]/[F-] ratio of 0.55 and 0.7 for the two reactors, respectively. CFD simulation showed the impact of inlet diameter, bottom-angle shape and width and height ratio of the reactor on mixing inside reactor and possibility of further improvement in reactor performance by optimizing the FBR configuration.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

(1) Background: The compound ytterbium trifluoride is used as a component of several dental materials, and this is reviewed in the current article. (2) Methods: Published articles on this substance were identified from PubMed, and showed that it has been included in a variety of dental restorative materials, including composite resins, glass polyalkenoate cements and calcium trisilicate cements. (3) Results: Ytterbium trifluoride is reported to be insoluble in water. Despite this, its presence is associated with fluoride release from dental materials. There is evidence that it reacts with the components of calcium trisilicate cements to form small amounts of a variety of compounds, including ytterbium oxide, Yb2O3, and calcium-ytterbium fluoride, CaYbF5. In nanoparticulate form, it has been shown to reinforce glass polyalkenoates and it also provides high contrast in X-ray images. (4) Conclusions: Ytterbium trifluoride is a useful component of dental materials, though some of the published findings suggest that there are aspects of its chemistry which are poorly understood.

The use of fluoride (F^-) for decreasing the prevalence and incidence of tooth decay was the greatest worldwide preventive public health measure of the 20th century. There have been controversial reports about the benefits of the use of F^-, because in small amounts it helps prevent dental caries, but in high concentrations it can be potentially toxic and harmful to dental and systemic health. Since the mid-20th century, F^- has been studied by toxicologists, looking at its deleterious effects in human populations. During the last decade, the interest on the undesirable effects has resurfaced because of the knowledge that it interacts with the cellular system, even in low doses, with a very small safety margin. Acute ingestion of toxic amounts of fluoride can cause corrosive gastric mucosa injury. Also respiratory effects such as bleeding, pulmonary edema, tracheostomy and shortness of breath, have been observed in individuals who inhale hydrogen fluoride. Some researchers had shown that F^- is an oxidizing agent and a well-known reversible enzymatic inhibitor that interferes with the enzyme activity of at least 80 proteins, can altered the intracellular redox equilibrium, lipid peroxidation, as well as, alteration in the gene expression and apoptosis induction. The primary purpose of this review is to examine findings of the action of inorganic F^-, and an overview of hard and soft tissue disturbances, known as fluorosis. The goal of this review is to enhance understanding of the mechanisms by which F^- affects cells with an emphasis on human tissue-specific events.

Salt stress is one of the major abiotic stresses that lead to crop yield reduction worldwide. Melatonin (MT), an endogenous hormone synthesized in plants, plays an important role in responding to abiotic stimuli such as drought, salinity, heat, cold, etc. However, the molecular mechanisms of MT-mediated abiotic stresses remain to be better understood. In order to explore the key genes and pathways of melatonin in alleviating salt stress, physiological and biochemical indicators as well as transcriptomics profile were conducted in alfalfa seedlings. The results showed that the germination rate, bud length and fresh weight of alfalfa seedlings added with melatonin were higher than those treated with salt alone. In addition, Malondialdehyde (MDA) and Superoxide anion (O2-) contents also displayed a decreasing trend. The activity and content of Superoxide dismutase (SOD)、peroxidase (POD) and Glutathione (GSH) increased to varying degrees. In order to further reveal the molecular mechanism of MT-mediated salt tolerance of alfalfa, transcriptome analysis was performed on alfalfa seedlings. 2,181 differentially expressed genes (DEGs) were obtained in the salt-treated group, including 780 upregulated genes and 1,401 down-regulated genes, while 4,422 DEGs were obtained in the MT group, among which 1,438 were upregulated and 2,984 were downregulated. By using GO functional annotation and KEGG pathway enrichment, we found that DEGs were mainly enriched in the biosynthesis of flavonoids, isoflavones, plant hormones, Glutathione (GSH), soluble sugars and other substances, as well as in the ABC transporter and MAPK signaling pathways. Among them, the DEGs in the MT group was more enriched in these pathways, suggesting that MT can combat salt stress by regulating the expression of genes related to phytohormone and antioxidant capacity, which has important reference value for the breeding of salt-tolerant alfalfa and other crops.

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

Upper mesophilic temperature acclimation of halophilic, hydrogen-producing bacteria from salt fields was investigated in this study, along with the changes in microbial abundance during an-aerobic digestion (AD) process. Genomic approaches such as PCR-denaturing gradient gel elec-trophoresis (DGGE) and next-generation sequencing (NGS) were performed to profile the mi-crobial communities. During AD, there was a significant abundance of Halanaerobacter lacunarum at 48°C followed by the increase in hydrogen yield, signifying potential contribution from the halophile in the hydrogen production. A decrease in the dominance of H. lacunarum and Halan-aerobium fermentans at 42°C, likely due to an increase in other bacterial species, was noted but their dominance significantly increased at temperatures of 45°C and 48°C. This investigation provides valuable insights in highlighting the potential of Halanaerobium sp. and the other halo-philic bacteria to adapt under upper mesophilic temperature conditions and synthesizing hy-drogen. The findings in the present study also underscore the importance of optimizing temper-ature and pH conditions to maximize hydrogen yield during high-salt anaerobic digestion.

High levels of groundwater containing both arsenic and fluorine are prevalent, resulting in serious health problems when consumed as drinking water. This co-pollution phenomenon is widespread and requires urgent attention. The multiple forms of arsenic and arsenic-fluorine co-contamination pose a significant challenge to efficiently co-remove both substances. This research utilized a green and stable synthesis approach to create MgLaFe LDO heterostructures, which were anchored on α-MnO2 nanowires. The materials comprise magnesium and lanthanum elements with a powerful attraction towards fluoride ions, elemental iron, which can establish stable compounds with arsenate, and MnO2, which can effectively oxidize arsenous acid, thereby enabling efficient co-removal of arsenic and fluorine. The efficient oxidation process of the MnO2 nanowire and the prompt ion adsorption process of the LDO work together synergistically. The adsorption performance was assessed through isotherm and kinetic fitting. Chemisorption was found to be the process for As(Ⅲ), As(V), and F- adsorption, with As(Ⅲ) going through monolayer adsorption on the surface of MnO2 nanowires, while As(V) and F- were mainly adsorbed by multilayer process on LDO. The maximum adsorption capacities were 111.76 mg/g, 230.51 mg/g, and 765.10 mg/g for As(Ⅲ), As(V), and F-, respectively. The XPS analysis provided further elucidation on the adsorption mechanism of the MnO2@LDO heterostructure, detailing each component's role in the process. The results confirm the successful construction of the heterostructure and its efficient coupling of oxidation and adsorption.

Ectopic expression of the MYB transcription factor of AmROSEA1 from Antirrhinum majus has been reported to change anthocyanin and other metabolites in several species. In this study, we found that overexpression of AmRosea1 significantly improved the tolerance of transgenic rice to drought and salinity stress. Transcriptome analysis revealed that a considerable amount of stress-related genes were affected by exogenous AmRosea1 during both drought and salinity stress treatments. These affected genes are involved in stress signal transduction, the hormone signal pathway, ion homeostasis and the enzymes that remove peroxides. This work suggests that the AmRosea1 gene is a potential candidate for genetic engineering of crops.

A reduction in population sodium (as salt) consumption is one of the most cost-effective strategies to reduce the burden of cardiovascular disease and it is a global health priority. High potassium intake is also recommended to reduce cardiovascular disease. To establish effective policies for setting targets and monitoring effectiveness within each country, the current level of consumption should be known. Greece lacks data on actual sodium and potassium intakes. The aim of the present study was therefore to assess dietary salt (using sodium as biomarker) and potassium intakes in a sample of healthy adults in northern Greece and to determine whether adherence to a Mediterranean diet is related to different sodium intakes or sodium-to-potassium ratio. A cross-sectional survey was carried out in Thessaloniki greater metropolitan area (northern Greece) (n=252, aged 18-75 years, 45.2% males). Participants’ dietary sodium and potassium intakes were determined by 24h urinary sodium and potassium excretions. In addition, we estimated their adherence to Mediterranean diet by the use of an 11-item MedDietScore (range 0-55). The mean sodium excretion was 175 (SD 72) mmol/day, equivalent to 4,220 (1,745) mg of sodium or 10.7 (4.4) g of salt per day and potassium excretion was 65 (25) mmol/day, equivalent to 3,303 (1,247) mg/day. Men had higher sodium and potassium excretions compared to women. Only 5.6% of the sample had salt intake <5g/d, which is the target intake recommended by the WHO. Mean sodium-to-potassium excretion ratio was 2.82 (1.07). There was no significant difference in salt or potassium intake or their ratio across MedDietScore quartiles. No significant relationships were found between salt intake and adherence to Mediterranean diet, suggesting that the perception of the health benefits of the Mediterranean diet does not hold when referring to salt consumption. These results suggest the need for a larger nation-wide survey on salt intake in Greece and underline the importance of continuation of salt reduction initiatives in Greece.

Owing to the expansion of non-face-to-face activities, security issues in video conferencing systems are becoming more critical. In this paper, we focus on the end-to-end encryption (E2EE) function among security services of video conferencing systems. First, the E2EE-related protocols of Zoom and Secure Frame (SFrame), which are representative video conferencing systems, are thoroughly investigated, and the two systems are compared and analyzed overall. Next, the E2EE protocol in the Government Public Key Infrastructure (GPKI)-based video conferencing system, in which the user authentication mechanism is fundamentally different from those used in private sector systems, such as Zoom or SFrame, will be considered. In particular, among E2EE-related protocols, we propose a detailed mechanism in which the post-quantum cryptography (PQC) key encapsulation mechanism (KEM) is applied to the user key exchange process. As the session key is not disclosed to the central server even in futuristic quantum computers, the mechanism to which the PQC KEM method proposed in this study is applied satisfies the E2EE security requirements and can be applied to domestic GPKI-based systems. It is expected to contribute in strengthening the safety of the next-generation video conferencing system.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

The evaporation of polymer solution droplet is an important in solution-based polymer film fabrications, such as inkjet print, spray coatings, and droplet casting etc. In this work, we investigated the effect of droplet size, solvent evaporation rate, and concentration on “coffee-ring” effect, crystal nucleation, polymorphism, and morphology of dried poly (vinylidene fluoride) (PVDF) solution droplets with atomic force microscopy (AFM) method. We found that the crystal structure, morphology and crystal distribution in the center and edge regions of dried PVDF droplets were different due to “coffee-ring” effect. The “coffee-ring” effect of dried PVDF droplets was mainly composited of accumulated crystals at the edge region of droplet, which was mainly made by crystallization of migrated chains. The interplay between migration of chains, crystallization and solidification of PVDF droplets significantly influenced the formation of “coffee-ring”. In addition, our results showed that the decrease of droplet size and controlling solvent evaporation rate were effective ways to improve the PVDF β-phase nucleation and decrease crystal size.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

World Health Organization recommends adjusting the salt intake as a part of the nine global targets to reduce premature mortality from non-communicable chronic diseases as priority and most cost-effective intervention. In 2006. the main aim of the Croatian Action on Salt and Health was to decrease salt intake for 16% because of its critical intake and consequences on human health. We have organized educative activities for increasing awareness on salt harmfulness, defined food categories of prime interest, collaborate with industries and determine salt intake (24h urine-sodium excretion). It was determined that the proportion of salt in ready-to-eat baked bread should not exceed 1.4%. In the period 2014 –2022, salt in the semi-white bread was reduced 14%, in bakery 22% and in largest meat industry in Croatia 25%. Awareness of the harmfulness of salt on health increased from 65.3% in 2008 to 96.9% in 2023 and salt intake was reduced 15.9%-1.8 grams/day (22.8% men, 11.7% women). In last 18 years a significant decrease in salt intake was achieved in Croatia, awareness of its harmfulness increased, collaboration with food industry established and regulatory documents launched. However, salt intake is still very high underlying the need for continuation of efforts and even stronger activities.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

This study evaluated the effects of fluoride on subsurface enamel demineralization induced by two commonly used chemical models. Forty-eight enamel blocks were demineralized at pH = 5.0 by an acetate buffer (Group 1), a lactate buffer (Group 2), an acetate buffer with 0.02 ppm fluoride (Group 3) and a lactate buffer with 0.02 ppm fluoride (Group 4) at 25 °C for 3 weeks. The surface destruction percentage (SDP), mineral loss and lesion depth of the blocks were studied using micro-computed tomography. An elemental analysis of the enamel surface was evaluated using an energy-dispersive X-ray spectroscopy. Surface micro-hardness was determined by the Knoop Hardness Test. The mean lesion depth of Groups 1 through 4 were 134.1 ± 27.2 µm, 96.1 ± 16.5 µm, 97.5 ± 22.4 µm and 91.1 ± 16.2 µm, respectively (p < 0.05; group 1 > 2, 3 > 4). The SDPs of groups 1 through 4 were 7.8 ± 8.93%, 0.71 ± 1.6%, 0.36 ± 1.70% and 1.36 ± 2.94% (p < 0.01; group 1 > 2, 3, 4). The fluoride in mean weight percentages of groups 1 through 4 were 1.12 ± 0.24%, 1.10 ± 0.20%, 1.45 ± 0.40% and 1.51 ± 0.51%, respectively (p < 0.01; group 3,4 > 1,2). The mean Knoop hardness values of groups 1 through 4 were 27.5 ± 13.3, 39.7 ± 19.3, 73.6 ± 44.2 and 91.0 ± 57.2, respectively (p < 0.01; group 4 > 3 > 2 > 1). The chemical model using an acetate buffer solution created significantly deeper zones of subsurface demineralization on enamel than the lactate buffer solution. An acetate buffer may damage the enamel surface, but the surface damage can be prevented by adding fluoride.

The technological development of piezoelectric materials is crucial for developing wearable and flexible electromechanical devices. There are many inorganic materials with piezoelectric effects, such as piezoelectric ceramics, aluminum nitride, and zinc oxide. They all have very high piezoelectric coefficients and large piezoelectric response ranges. The characteristics of high hardness and low tenacity make inorganic piezoelectric materials unsuitable for flexible devices that require frequent bending. Polyvinylidene fluoride (PVDF) and its derivatives are the most popular materials used in flexible electromechanical devices in recent years and have high flexibility, high sensitivity, high ductility, and a certain piezoelectric coefficient. Owing to increasing the piezoelectric coefficient of PVDF, researchers are committed to optimizing PVDF materials and enhancing their polarity by a series of means to further improve their mechanical–electrical conversion efficiency. This paper reviews the latest PVDF-related optimization materials, related processing and polarization methods, and the applications of these materials such as those in wearable functional devices, chemical sensors, biosensors, and flexible actuator devices for flexible micro-electromechanical devices. We also discuss the challenges of wearable devices based on flexible piezoelectric polymer, consider where further practical applications could be.

The main objective of this communication is to describe the ‘Global Salt Cycle’. Giant salt accumulations are commonly found along continental margins of former rifts. The first stage in the accumulation process is saturation of newly formed oceanic crust with seawater. Final mobilisation and accumulation of the salts occurs during rifting, localised in the vicinity of relict subduction zones. Oceanic crust is created along the spreading ridges in the deep oceans of the Earth. It exchanges mass and energy with seawater in hydrothermal circulation cells that penetrate deep into the new and fractured crust. Water-rock interactions include the formation of hydrated and hydroxylated minerals, e.g., serpentinites and clay minerals. By incorporating hydroxyl groups and water in their crystal lattices, the salinity of remaining brines increases. Subduction of oceanic crust and serpentinised lithosphere transports water, hydrated minerals, and marine salts deep into the crust and mantle. Upon pressurisation and heating of the subducting slab, different parts of this water are expelled at different depths/temperatures. The resulting fluids will contain salts brought in with the slab, as well as new salts formed by water-rock interaction. The combination of elevated pressures and temperatures, water, salinity, and CO2, create permeability in the normally impermeable, peridotitic mantle, by altering the fluid-rock dihedral angles of mineral grains. This P/T-determined intergranular permeability allows ascent of saline fluids, under lithostatic pressure, within the mantle wedge, or the slab itself. The fluids produce a mechanically weakened and buoyant zone within the mantle wedge due to high pore pressure between mineral grains and reduced mantle density. During the lifetime of a subduction zone, a substantial accumulation of saline fluids within the mantle wedge and crust, is evident. Deep, fluid reservoirs accumulate between the subduction trench and the volcanic front. They may exist for hundreds of millions of years, even after the extinction of the subduction zone. Saline fluids may escape to the surface along deep faults, due to overfilling of available pores/fractures. Fluids within the mantle wedge may form rock melts or exist as supercritical, mineral rich fluids. The combination of reduced pressure due to rifting, and a saline and buoyant mantle, creates a mantle circulation that brings the accumulated, saline fluids, to crustal levels. Salts will therefore accumulate during initial stages of rifting as a result of massive fluid expulsion, phase change and boiling of mantle fluids. No extra energy is required to produce phase change and boiling. The result is formation of solid salts or dense brines/slurries invading fractured crustal rocks, or escaping to the surface/seabed. This process may take place both before and after the sea has invaded a continental rift.

The separator membrane is an essential component of lithium-ion batteries, separating the anode and cathode and controlling the number and mobility of the lithium ions. Among the polymer matrices most investigated for battery separators are poly(vinylidene fluoride) (PVDF) and its copolymers poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), and poly(vinylidene fluoride-cochlorotrifluoroethylene) (PVDF-CTFE), due to their excellent properties such as high polarity and the possibility of controlling the porosity of the materials through binary and ternary polymer/solvent systems, among others. This review presents the recent advances on battery separators based on poly(vinylidene fluoride) (PVDF) and its copolymers for lithium-ion batteries. It is divided in the following sections: single polymer and co-polymers, surface modification, composites and polymer blends. Further, a critical comparison between those membranes and other separator membranes is presented, as well as the future trends on this area.

PEBAX-2533/metal salt/Al salt membranes were prepared for mixed olefin/paraffin separation. PEBAX-2533 with 80% ether group and 20% amide group was suggested as the polymer matrix for comparison of separation performance according to the functional group ratio in copolymer PEBAX. In addition, Al salts were used to stabilize metal ions for a long time as additives. High permeance was expected with the proportion of high ether groups since these functional groups provided relatively permeable regions. As a result, the PEBAX-2533 composite membrane showed a selectivity of 5 (propylene/propane) with 10 GPU. However, the permeance of membrane was not unexpectedly improved and the selectivity was reduced. The result was analyzed by SEM, FT-RAMAN and TGA, including FT-IR. The reduction in separation performance was determined by FT-IR. From these results, in order to stabilize the metal ions interacting with the polymer through Al(NO3)3, it was concluded that specific ratio of amide group was needed in PEBAX as polymer matrix.

Endothall dipotassium salt and monoamine salt are herbicide formulations used for controlling submerged aquatic macrophytes and algae in aquatic ecosystems. Microbial activity is the primary degradation pathway for endothall. To better understand what influences endothall degradation, we conducted a mesocosm experiment to 1) evaluate the effects of different water and sediment sources on degradation, and 2) determine if degradation was faster in the presence of a microbial community previously exposed to endothall. Endothall residues were determined with LC-MS at intervals to 21 days after endothall application. Two endothall isomers were detected. Isomer-1 was abundant in both endothall formulations, while isomer-2 was only abundant in the monoamine endothall formulation and was more persistent. Degradation did not occur in the absence of sediment. In the presence of sediment degradation if isomer-1 began after a lag phase of 5-11 days and was almost complete by 14 days. Onset of degradation occurred 2-4 days sooner when the microbial population was previously exposed to endothall. We provide direct evidence that the presence and characteristics of sediment are of key importance in the degradation of endothall in an aquatic environment, and that monoamine endothall has two separate isomers that have different degradation characteristics.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process of delivering this technology. The topic of the control and shut down for a zero power reactor is for the first time introduced through a literature review and the reduction of the control approaches to a limited number of basic functions with different variations. In the following, the requirements for the control and shutdown system for a reactor experiment are formulated, and based on these assessments, an approach for the shutdown – splitting the lower part of the core with reflector, and an approach for the control – a vertically movable radial reflector are proposed. Both systems will be usable for a zero-power system with a liquid as well as with as a solid core and even more importantly, both systems somehow work on the integral system level without disturbing the central part of the core which will be the essential area for the experimental measurements. Both approaches have been investigated as a singular system as well as their interactions with one another and the sensitivity of the control system. The study has demonstrated that both proposed systems are able to deliver the required characteristics with sufficient shutdown margin and a sufficiently wide control span. The interaction of the system has been shown to be manageable and the sensitivity is on a very good level. The multi-group Monte-Carlo approach has been cross evaluated by a continuous energy test leading to good results, but they also demonstrate that there is room for improvement.

High nitrate and fluoride contamination in groundwater cause a variety of disorders, including methemoglobinemia, teratogenesis, and dental and skeletal fluorosis. The present work assesses the non-carcinogenic health risks posed by nitrate and fluoride in infants, children, and adults using the USEPA method. Groundwater samples were collected from 36 wells and boreholes in three central Saudi Arabia study areas. Nitrate concentrations varied from 0.70 to 47.00 mg/L. None of the 36 studied boreholes had nitrate levels that exceeded WHO guidelines (50.00 mg/L). Fluoride ranged from 0.63 to 2.00 mg/L, and 30.55% of the fluoride samples (11 out of 36) exceeded the WHO recommendations for acceptable drinking water (1.5 mg/L). The average hazard index (HI) values for adults, children, and infants were 0.99, 2.59, and 2.77, respectively. Water samples surpassed the safety level of 1 for adults, children, and infants at 44.44, 97.22, and 100%, respectively. Accordingly, water samples from Jubailah and a few from Wadi Nisah may expose infants, children, and adults to non-cancer health concerns. Infants and children are more vulnerable to non-carcinogenic health risks than adults, possibly due to their lower body weight.

Excessive intake of fluoride, one of the trace elements to maintain health, leads to liver injury. Tetramethylpyrazine (TMP) is a kind of traditional Chinese medicine monomer with good antioxidant and hepatoprotective function. The aim of this study was to investigate the effect of TMP on liver injury induced by acute fluorosis. A total of 60 1-month-old male Institute of Cancer Research mice without carriage of pathogenic bacteria were selected. All mice were fed adaptively for one week, and then randomly divided into 5 groups: control (K) group, model (F) group, low-dose (LT) group, medium-dose (MT) group and high-dose (HT) group. The control and model group were given distilled water, while 40 mg/kg (LT), 80 mg/kg (MT) and 160 mg/kg (HT) TMP were fed by gavage for two weeks with the maximum gavage volume of mice is 0.2ml/10g/d. Except for the control group, all groups were given fluoride (35 mg/kg) by intraperitoneal injection on the last day of the experiment. The results of this study showed that compared with the model group, TMP alleviated the pathological changes of liver induced by fluoride and improved the ultrastructure of liver cells; TMP significantly decreased the levels of ALT, AST and MDA (P <0.05), and increased the levels of T-AOC, T-SOD and GSH (P <0.05). The results of mRNA detection showed that TMP significantly increased the mRNA expression levels of Nrf2, HO-1, CAT, GSH-Px and SOD in liver compared with model group (P <0.05). In conclusion, TMP can inhibit oxidative stress by activating Nrf2 pathway and alleviate liver injury induced by fluoride.

Background: Fluoride toothpaste (FT) has recently been included in the World Health Organization’s (WHO) Model List of Essential Medicines. Whereas it is essential for preventing dental caries, its current affordability around the globe remains unclear. This study aimed to analyse the affordability of FT in as many as possible countries worldwide. Methods: A standardized protocol was developed to collect country-specific information about the characteristics of the cheapest FT at a common point of purchase. 82 members of the WHO Global Oral Health Network of Chief Dental Officers (CDOs), directors of WHO Collaborative Centres and other oral health experts collected data using mobile phone technology. The Fluoride Toothpaste Affordability Ratio (FTAR) was calculated as the price associated with the recommended annual consumption of FT, relative to the daily wage of the lowest-paid unskilled government worker (FTAR >1 = unaffordable spending on fluoride toothpaste). The daily expenditure per capita of the poorest 15% of the income distrubition was used as the main proxy of the daily wage, using World Bank data. Alternatively, we used the daily minimum wage as a proxy of the daily wage. Stratified descriptive statistics were undertaken with respect to different World Bank Income Groups and WHO Regions. Results: There are significant discrepancies in the affordability of FT across 78 countries. FT was strongly affordable in high-income countries, relatively affordable in upper middle-income countries, and strongly unaffordable in lower middle-income and low-income countries. The affordability of FT across WHO Regions was dependent upon the economic mix of WHO Regions’ member states. Conclusion: FT is still unaffordable for many people, particularly in low-resource settings. Health policy members should develop better strategies to address and improve the universal affordability of FTs, for the incidence of dental caries to be reduced at a global level.

A dual-platform colorimetric and ratiometric chemosensor, namely 6-(2-hydroxynaphthalen)-N-n-butyl-naphthalimide (HNA), based on Schiff base constructed from N-n-butyl-4-amino-1,8-naphthalimide and 2-hydroxy-1-naphthaldehyde has been designed and fabricated for detecting fluoride anion (F−) in DMSO solution. HNA is a colorimetic and ratiometric probe with superior selectivity and sensitivity. The color changes of HNA from yellow to purple was observed by the naked eyes in the presence of F−. The absorbance in the UV-Vis spectra of HNA was decreasing in 422 nm, while gradually increasing in 583 nm by adding F−. The limit of detection (LOD) of HNA for detecting F− is low to 0.61 μM and the binding model of HNA and F− is in 3:2 stoichiometry. Meanwhile, HNA can be used to detect F− in real samples. Finally, the mechanism of HNA for the detection of F− was investigated. The present work indicated that HNA would be a superior potential chemosensor in monitoring F− selectively and sensitively.

PZT-Poly(vinylidene fluoride) composites were prepared by hot-pressing method. Before addition, PZT particles were firstly modified with two different coupling agents. The micromorphology, microstructure, dielectric properties, and piezoelectric properties of the composites were characterized and investigated. Results indicated that PZT particles were homogeneously dispersed in the PVDF matrix by the addition of coupling agents. The electric properties of PZT-PVDF composites with NDZ-101 were the best. Especially when the volume ratio of the titanate coupling agent NDZ-101 was 1%, the piezoelectric strain constant d33 of PZT-PVDF composites reached maximum value 19.23pC/N; its relative dielectric constant εr was 67.45; at the same time its dielectric loss tanδ was 0.0766.

Herein, we report results of the study of the composite ferroelectric scaffolds based on vinylidene fluoride-tetrafluoroethylene copolymer (VDF-TeFE) and polyvinylpyrrolidone (PVP) produced by electrospinning and their application as a wound-healing material. The physicochemical properties of ferroelectric composite polymer scaffolds depending on the content of PVP (in the range from 0 to 50 wt %) including morphology, composition and crystalline structure were studied. The cytotoxicity of materials and the proliferative activity of cells during their cultivation on the surface of formed scaffolds are reported. It has been found that the optimal PVP content in the VDF-TeFE composite scaffolds is 15 wt%. On a model of a full-thickness contaminated wound in vivo, it was shown that piezoelectric scaffolds based on VDF-TeFE copolymer containing 15 wt% PVP provide better wound healing results in comparison with standard gauze dressings impregnated with a solution of an antibacterial agent.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process delivering this technology. The choice of the optimal reflector material is one of the key issues for such experiments since on the one hand it offers huge cost saving potential due to reduced fuel demand, on the other hand an improper choice of the reflector material can have negative effects on the quality of the experiments. The choice of the reflector material is for the first time introduced through a literature review and a discussion of potential roles of the reflector. The 2D study of different potential reflector materials has delivered a first down selection with SS 304 as representative for stainless steel, lead, copper, graphite, and beryllium oxide. A deeper look identified in addition iron-based material with high Si content. The following evaluation of the power distribution has shown the strong influence of the moderating reflectors creating a massively disturbed power distribution with a peak at the core boundary. This effect has been confirmed through a deeper analysis of the 2D multi-group flux distribution which lead to the exclusion of the BeO and the graphite reflector. The most promising materials identified have been SS 304, lead, and copper. The final 3D Monte-Carlo study demonstrated that all three materials have the potential to reduce the required amount of fuel by up to 60% compared NaCl which has been used in previous studies and is now taken as reference A first cost analysis has identified the SS 304 reflector as the most attractive solution. The results of the 2D multi group deterministic study and the 3D multi group Monte-Carlo study have been confirmed through a continuous energy Monte-Carlo reference calculation showing only minor differences.

Keywords: Knowledge; Attitudes; Practices; Salt intake.

This study was undertaken to elucidate the role of trehalose (Tre) in mitigating oxidative stress under salinity and low P in maize. Eight-day-old maize seedlings of two maize varieties, BARI Hybrid Maize-7 and BARI Hybrid Maize-9 were subjected to salinity (150 mM NaCl), low P (5 µM KH2PO4) and their combined stress with or without 10 mM Tre for 15-d.Salinity and combined stress significantly inhibited the shoot length, root length, and root volume, whereas, low P increased the root length and volume in both genotypes. Exogenous Tre in the stress treatments increased all of the growth parameters as well as decreased the salinity, low P and combined stress-mediated Na+/K+, ROS, MDA, LOX activity and MG in both genotypes. Under salinity and low P stress, the SOD activity increased in both genotypes, but the activity decreased in combined stress. POD activity increased in all stress treatments. Interestingly, Tre application enhanced the SOD activity in all the stress treatments but inhibited the POD activity. Both CAT and GPX activity were increased by saline and low P stress while the activities inhibited in combined stress. Similar results were found for APX, GR, and DHAR activities in both genotypes. However, MDHAR activity was inhibited in all the stresses. Interestingly, Tre enhanced CAT APX, GPX, GR, MDHAR and DHAR activities suggesting the amelioration of ROS scavenging in maize under all the stresses. Increased GST activity in presence or absence of Tre might involve in detoxification of hydroperoxides as well as leaf senescence. On the other hand, increased glyoxalase activities in saline and low P stress in BHM-9 suggested better MG detoxification system because of down-regulation of Gly-I activity in BHM-7 in those stresses. Tre also increased the glyoxalase activities in both genotypes under all the stresses. Tre improved the growth in maize seedlings by decreasing Na+/K+, ROS, MDA, and MG through regulating antioxidant and glyoxalase systems.

Sphingosine 1-phosphate (S1P) is a signaling lipid molecule involved in various cellular processes. It is important to develop a quantitative method for S1P to determine endogenous levels and to investigate its functions. Especially since S1P is a tiny lipid component of most biological samples, highly sensitive analysis by LC-MS/MS is required. The main challenge in S1P analysis by chromatography is peak broadening due to the presence of a polar phosphate and zwitterion formation in S1P. In this study, we used hydrogen fluoride (HF) to efficiently remove a phosphate and then analyzed the surrogate, sphingosine, as a sharp peak by LC-ESI-MS/MS. We optimized the dephosphorylation reaction in terms of reaction time, temperature, and HF concentration. Multiple reaction monitoring (MRM) for dephosphorylated form of S1P and C17-S1P as internal standard at m/z transition 300.4&gt;282.4 (quantification ion), 300.4&gt;262.4 (qualification ion), 286.3&gt;268.2 (internal standard). This method was validated by essential parameters such as specificity, linearity, range, LOQ, LOD, accuracy, precision, and repeatability. To confirm this new method, we quantified S1P levels in various serum products (100.02 ~ 284.38 nM). To apply the method in vivo, we analyzed S1P in plasma and kidney tissues obtained from a chronic kidney disease (CKD) mouse model. S1P levels were increased only in CKD kidney tissue but not in plasma. In conclusion, by applying the dephosphorylation step with HF, we established a new sensitive LC-MS/MS quantitative method for S1P that can be applied to biological samples.

The major challenge for membrane distillation (MD) is membrane wetting resistance induced by pollutants in the feed solution. The proposed solution for this issue was to fabricate membranes with hydrophobic properties. Hydrophobic electrospun Poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofibers membranes were produced for brine treatment using the direct contact membrane distillation (DCMD) technique. These nanofibers membranes were prepared from three different polymeric solution compositions to study the effect of solvent composition in the electrospinning process. Further, the effect of the polymer concentration was investigated by preparing polymeric solutions with three different polymer percentages: 6, 8, and 10%. All nanofibers membranes obtained from electrospinning were post-treated at varying temperatures. The effects of thickness, porosity, pore size, and LEP were studied. The hydrophobicity was determined by contact angle measurements, which were investigated by optical contact angle goniometry. The crystallinity and thermal properties were studied by DCS and XRD, while the functional groups were studied by FTIR. The morphological study was performed by AMF and described the roughness of nanofibers membranes. Finally, all nanofibers membranes have enough of a hydrophobic nature to be used in DCMD. PVDF membrane filter disc and all nanofibers membranes were applied in DCMD to treat brine water. The resulting water flux and permeate water quality were compared, and it was discovered that all produced nanofibers membranes showed good behavior with varying water flux, but the salt rejection was greater than 90%. A membrane prepared from DMF/acetone 5-5 with 10% PVDF-HFP provided perfect performance, with an average water flux of 44 kg.m-2.h-1 and salt rejection of 99.8%.

This work is devoted to consideration and analysis of the application of molecular dynamics simulation (MDS) methods to the study of nanosized polymer polyvinylidene fluoride (PVDF) thin ferroelectric films (two-dimensional ferroelectrics) and their composites with graphene layers: 1) to study and calculations of the polarization switching time depending on the electric field and PVDF film thickness; 2) to study and calculations of the polarization switching time depending changes of the PVDF on PVDF-TrFE film; 3) to study the polarization switching time in PVDF under influence of graphene layers. All calculations at each MDS step were carried out using quantum semi-empirical methods PM3. A comparison and analysis of the results of these calculations and the kinetics of polarization switching within the framework of the Landau-Ginzburg-Devonshire theory for homogeneous switching in ferroelectric polymer films is carried out. The study of the composite heterostructures of the “graphene-PVDF” type and calculations of their polarization switching times were presented too. It is shown that replacing PVDF with PVDF-TrFE significantly changes the polarization switching times in these thin polymer films, and that introducing various graphene layers into the PVDF layered structure leads to both an increase and a decrease in the polarization switching time. Here everything also depends on the position and displacement of the ferroelectric coercive field depending on the system damping parameters.

This review deals with the adaptive mechanisms that plants can implement to cope with the challenge of salt stress. Plants tolerant to NaCl implement a series of adaptations to acclimate to salinity, including morphological, physiological and biochemical changes. These changes include increases in the root/canopy ratio and in the chlorophyll content in addition to changes in the leaf anatomy that ultimately lead to preventing leaf ion toxicity, thus maintaining the water status in order to limit water loss and protect the photosynthesis process. Furthermore, we deal with the effect of salt stress on photosynthesis and chlorophyll fluorescence and some of the mechanisms thought to protect the photosynthetic machinery, including the xanthophyll cycle, photorespiration pathway and water-water cycle. Finally, we also provide an updated discussion on salt-induced oxidative stress at the subcellular level and its effect on the antioxidant machinery in both salt-tolerant and salt-sensitive plants. The aim is to extend our understanding of how salinity may affect the physiological characteristics of plants.

Mangroves and salt marshes are among the most productive ecosystems in the global coastal ocean. Mangroves store more carbon (739 Mg CORG ha-1) than salt marshes (334 Mg CORG ha-1), but the latter sequester proportionally more (24%) net primary production (NPP) than mangroves (12%). Mangroves exhibit greater rates of gross primary production (GPP), above-ground net primary production (NPP) and plant respiration (RC) with higher PGPP/RC ratios, but salt marshes exhibit greater rates of below-ground NPP. Mangroves have greater rates of subsurface DIC production and, unlike salt marshes, exhibit significant microbial decomposition to a soil depth of 1 m. Salt marshes release more soil CH4 and export more dissolved CH4 , but mangroves release more CO2 from tidal waters and export greater amounts of POC, DOC and DIC to adjacent waters. Both ecosystems contribute only a small proportion of GPP, RE (ecosystem respiration) and NEP (net ecosystem production) to the global coastal ocean due to their small global area, but contribute 72% of air-sea CO2 exchange from the world’s wetlands and estuaries and contribute 34% of DIC export and 17% of DOC + POC export to the world’s coastal ocean. Thus, both wetland ecosystems contribute disproportionately to carbon flow of the global coastal ocean.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

As bread is the most consumed food by Tunisian population and the major source of salt, a pilot experience of salt reduction in bread has already begun in Bizerte city. Salt analysis in bread collected from Bizerte city was realized with Volhard titration method. Application of the “salt reduction programme” allowed a gradual decrease of salt content in bread by 35 % during three years without detection by Tunisian consumers. A final salt concentration of 1.1 ± 0.1 g/100 g was then achieved. The establishment of an effective salt reduction strategy with lifestyle education is needed to reduce hypertension that is the first cause of death in Tunisia.

In the present study, Electrocoagulated Metal Hydroxide Sludge (EMHS) was analyzed as adsorbent material to remove both fluoride ion (F-) and arsenic V (As(V)) from aqueous effluents. This material was generated during an electrocoagulation process using Aluminum anode. It was characterized by using specific surface areas and the surface morphology was studied by scanning electron microscopy (SEM). Adsorbent fixed-beds are generally studied to remove different class of contaminants. EMHS was evaluated using a continuous flow rate column test with an experimental design. The effect of initial concentration of F- (2.5–10 mg L⁻¹) and the Empty Bed Contact Time (EBCT (0.4–0.8 min)) was studied following a central composite design methodology. The experimented parameters had a significant influence on saturation time, breakthrough volume, and breakthrough time. A response surface analysis was a tool for analyzing the adsorption study, showing interactions that are complicated to identify by others methods. The results, here reported, revealed that EMHS is an efficient and promising adsorbent material in order to remove F- and As(V) from water contaminated by these pollutants.

As predicted by the theory of super dielectric materials, simple tests demonstrate that dielectric material on the outside of a parallel plate capacitor dramatically increases capacitance, energy density, and power density. Simple parallel plate capacitors with only ambient air between the plates behaved as per standard theory. Once the same capacitor was partially submerged in deionized water [DI], or DI with low dissolved NaCl concentrations, still with only ambient air between the electrodes, the capacitance, energy density, and power density, at low frequency, increased by more than seven orders of magnitude. Notably, conventional theory precludes the possibility that material outside the volume between the plates will in any fashion impact capacitive behavior.

High concentrations of sodium (Na+), chloride (Cl-), calcium (Ca2+), and sulphate (SO42-) are fre-quently found in saline soils. Crop plants cannot successfully develop and produce because salt stress impairs the uptake of calcium, potassium, and water into plant cells. Different intracellular and extracellular ionic concentration changes by salinity, including those of calcium, potassium, and protons. These cations serve as stress signaling molecules in addition to being essential for ionic homeostasis and nutrition. Maintaining an appropriate K+: Na+ ratio is one crucial plant mechanism for salt tolerance, which is a complicated trait. Another important mechanism is the ability for fast extrusion of Na+ from the cytosol. Calcium is established as a ubiquitous secondary messenger, which transmits various stress signals into metabolic alterations that cause adaptive responses. When plants are under stress, the cytosolic-free Ca2+ concentration can rise to 10 times or more from its resting level of 50-100 nanomolar. Reactive oxygen species (ROS) are linked to the calcium alterations, and are produced by stress. Depending on the type, frequency and intensity of the stress, the cytosolic calcium signals oscillate, are transient, or persist for a longer period and exhibit specific "signatures". Both the input and efflux of Ca2+ from the cytosol affect the length and amplitude of the signal. According to several reports, under stress calcium alterations can occur not only in the cytoplasm of the cell but also in the cell walls, nucleus and other cell organelles and the calcium waves propagate through the whole plant. Here, we will focus on how wheat and other important crops absorb Na+, K+ and Cl- when plants are under salt stress, as well as how calcium, potassium, and pH cause intracellular signaling and homeostasis. Similar mechanisms in the model plant Arabidopsis will also be considered.

Nanofiber (NF) products exhibit outstanding performances in the materials science, textile, and medical fields, which cannot be realized using conventional technologies. However, the safety of such products is debated because of the potential risk of nanomaterials and lack of standardized guidelines for safely evaluating NF products. The global safety evaluations of nanomaterials focused on evaluating the cytotoxicity of zero-dimensional materials including nanoparticles and nanotubes based on OECD criteria. The NFs are one-dimensional materials with nanometer diameters and considerable lengths. Many fibers are applied in a densely woven web-like form, and therefore, assessing cellular penetration and fiber toxicity using the same methods is inappropriate. This study verifies the safety of polyurethane (PU) and polyvinylidene fluoride (PVDF) polymers, which are currently applied in filters and masks. To this end, polymer NFs were collected from each product, and the NFs were compared with reference samples considering their physical properties using FT-IR and Raman spectroscopy. For the safety evaluation, DMSO stocks of varying concentrations of PVDF and PU NFs (at 0.5, 1, 5, and 10 μg/mL) were prepared, and the cytotoxicity and inhibitory effects on nitric oxide production and protein expression obtained via Western blot were identified.

(1) Background: The aim of study was to investigate the salt consumption by children and adolescents from the Silesian Province (Poland), taking into account the region’s dietary traditions and number of years of school education. (2) Methods : 300 students aged 10–18 from different types of schools, were enrolled in the study and divided into groups in terms of: school, sex, the state of nutrition. The survey questionnaire about dietary habits, including the frequency and serving size with respect to 12 salty products was used. On the basis of the frequency and the amount of consumed products, as well as the data on salt content, the amount of total daily intake of salt was estimated.; (3) Results: The mean daily intake of salt by children and adolescents was 1.083 g ( 0.433 g of sodium); children aged 10–12 consumed the highest amount of salt (1.296 g/day) compared to pupils aged 13–15 (1.131 g of sodium) and adolescents aged 16–18 (0.863 g/day); (4) Conclusions: With age, as a result of various factors, the consumption of salt declines. The parents impact and the familial socio-environmental factors begin to wane, and other factors start to have influence, e.g. school education of healthy lifestyle, health behavior of peers.

In the semi-arid region of Brazil, it is common to use saline or brackish water for crop production. However, this practice can negatively affect the soil, nutrient balance, and fruit quality and production. From this perspective, this study aimed to evaluate the effect of fertilization combinations with nitrogen (N), phosphorus (P), and potassium (K) on the production and quality of West Indian cherry grown under salt stress in the second year of production. The study was conducted in a protected environment following a randomized block design with treatments distributed in a 2 x 10 factorial arrangement referring to two levels of electrical conductivity of irrigation water (ECw) (0.6 and 4.0 dS m-1) and 10 NPK fertilization combinations (80-100-100; 100-100-100; 120-100-100; 140-100-100; 100-80-100; 100-120-100; 100-140-100; 100-100-80; 100-100-120 e 100-100-140% of the recommendation in the second year of production), with three replicates and one plant per lysimeter. The results indicate that irrigation of West Indian cherry crop irrigation at the water salinity of 4.0 dS m-1 negatively affected all fruit production variables. The interaction between the ECw of 0.6 dS m-1 and the 100-80-120 NPK fertilization combination increased the total number of fruits and the total fruit weight of West Indian cherry.

Ionizing radiation-induced damage in cancer and normal cells leads to apoptosis and cell death, through the intracellular oxidative stress, DNA damage and disorders of their metabolism. Irradiation doses that do not lead to the death of tumor cells can result in the emergence of radioresistant clones of these cells, due to the rearrangement of metabolism and the emergence of new mutations, including those in the genes responsible for DNA repair. The search for the substances capable of modulating the functioning of the tumor cell repair system is an urgent task. Here we analyzed the effect of cerium(III) fluoride nanoparticles (CeF3 NPs) on normal (human mesenchymal stem cells – hMSCs) and cancer (MCF-7 line) human cells after X-ray radiation. CeF3 NPs effectively prevent the formation of hydrogen peroxide and hydroxyl radicals in an irradiated aqueous solution, showing pronounced antioxidant properties. CeF3 NPs are able to protect hMSCs from radiation-induced proliferation arrest, increasing their viability and mitochondrial membrane potential, and, conversely, inducing the cell death of MCF-7 cancer cells, causing radiation-induced mitochondrial hyperpolarization. CeF3 NPs provided a significant decrease in the number of double-strand breaks (DSBs) in normal cells, while in MCF-7 cells the number of γ-H2AX foci dramatically increased in the presence of CeF3 4 hours after irradiation. In the presence of CeF3 NPs, there was a tendency to modulate the expression of most analyzed genes associated with the development of intracellular oxidative stress, cell redox status and the DNA repair system after X ray irradiation. Cerium-containing nanoparticles are capable of providing selective protection of normal cells from radiation-induced injuries and are considered as a platform for the development of promising clinical radioprotectors.

The amino acid proline accumulates in plants during abiotic stresses such as drought and salinity and is considered a reliable marker of environmental stress. While its accumulation is well established, its precise role in stress tolerance and its underlying molecular mechanism remain less clear. To address these issues, we performed a meta-analysis - a robust statistical technique that synthesizes results from multiple independent studies while accounting for experimental differences. We focused on 16 physiological and morphological parameters affected by drought and salt stress in transgenic plants expressing proline metabolic genes. For each parameter, we calculated the effect size as the response ratio (RR), which represents the logarithm of the mean value in the transgenic group over the mean value of the control group (lnRR). Under stress, most parameters exhibited significantly higher response ratios in the transgenic group, confirming the beneficial effects of proline during drought and salt stress. Surprisingly, under non-stressed conditions, most stress markers showed no significant differences between transgenic and non-transgenic plants, despite elevated proline levels in the former. These results suggest that the benefits of proline may be related to proline catabolism or may only become apparent during stress, possibly due to interactions with reactive oxygen species (ROS), which accumulate predominantly under stress conditions.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

Lack of water and salinity are common problems in many parts of the world. Therefore, some types of cacti can represent as promising crops. Therefore, the ability of cactus species to survive and adapt under natural stress conditions should be evaluated. In this study, it was aimed to evaluate the effect of salt stress on germination and emergence of pitaya seeds obtained from different fruit flesh colors, priming with plant growth regulators, namely salicylic acid (SA), oxalic acid (OA) and mepiquat chloride (MC). The experiment had a completely randomized design with a 2×4×3 factorial scheme corresponding to two pitaya cultivars (white and red fleshed), four NaCl concentrations (0, 2500, 5000 and 10000 ppm), and three PGRs (150 ppm/MC, SA, OC). The following variables were analyzed; germination percentage, mean germination time (MGT), germination stress tolerance ındex (GSTI), shoot length, seedling fresh weight and seedling dry weight ratio. According to the results, it was determined that the growing environment of the seed was important in salt stress resistance, while seeds matured in the environment with red fruit flesh were more tolerant to salt stress than white. Although Pitaya species are relatively salt tolerant, growth (about 30%) was significantly reduced above 2500 ppm and germination (about 45%) above 5000 ppm. MC was found promising as a priming agent in seeds obtained from fruits with white fruit flesh, and OA was found promising as a priming agent in seeds obtained from fruits with red fruit flesh in reducing NaCl-induced stress. Germination percentage stood out as the most important trait determining seed quality and was found to have positive effects on germination stress tolerance index (r: 0.63), seedling length (r: 0.74) and fresh seedling weight (r: 0.56). It is thought that the results obtained may contribute to pitaya cultivation and breeding.

Nuclear technologies have the potential to play a unique role delivering low carbon energy for a future net-zero society. However, for the long-term success, nuclear will need to deliver innovative solutions as proposed in iMAGINE. One of the key challenges for the envisaged highly integrated nuclear energy system is the need for a demand driven salt clean-up system. The work described provides an insight into the interplay between a potential salt clean-up system and the reactor operation in a dynamic approach. The results provided will help to optimize the parameters for the salt clean-up process by delivering a dynamically calculated priority list identifying the elements with high influence on reactor operation. The integrated model is used to investigate the ideal time for the initiation of the clean-up as well as the effect of different throughput through the clean-up system on criticality as well as on the concentration of the elements in the reactor salt. Finally, a staggered approach is proposed with the idea to phase in the chemical clean-up processes step by step to keep the reactor critical. The results provide an essential step for the progress of iMAGINE as well as the basis for the inter disciplinary work required to bring iMAGINE into real operation.

olten salt reactors (MSRs) utilize salts as coolant or as the fuel and coolant together with fissile isotopes dissolved in the salt. It is necessary to therefore understand the behavior of the salts to effectively design, operate, and regulate such reactors, and thus there is a need for thermodynamic models for the salt systems. Molten salts, however, are difficult to represent as they exhibit short range order that is dependent on both composition and temperature. A widely useful approach is the modified quasichemical model in the quadruplet approximation that provides for consideration of first and second nearest neighbor coordination and interactions. Its use in the CALPHAD ap-proach to system modeling requires fitting parameters using standard thermodynamic data such as phase equilibria, heat capacity, and others. Shortcoming of the model is its inability to directly vary coordination numbers with composition or temperature. Another issue is the difficulty in fitting model parameters using regression methods without already having very good initial values. The proposed paper will discuss these issues and note some practical methods for the effective genera-tion of useful models.

The role of hydrogen in a future energy system with a high share of variable renewable energy sources (VRES) is regarded as crucial in order to balance fluctuations in electricity generation. These fluctuations can be compensated for by flexibility measures such as the expansion of transmission, flexible generation, larger back-up capacity and storage. Salt cavern storage is the most promising technology due to its large storage capacity, followed by pumped hydro storage. For the underground storage of chemical energy carriers such as hydrogen, salt caverns offer the most promising option owing to their low investment cost, high sealing potential and low cushion gas requirement. This paper provides a suitability assessment of European subsurface salt structures in terms of size, land eligibility and storage capacity. Two distinct cavern volumes of 500,000 m³ and 750,000 m³ are considered, with preference being given for salt caverns over bedded salt deposits and salt domes. The storage capacities of individual caverns are estimated on the basis of thermodynamic considerations based on site-specific data. The results are analyzed using three different scenarios: onshore and offshore salt caverns, only onshore salt caverns and only onshore caverns within 50 km of the shore. The overall technical storage potential across Europe is estimated at 84.8 PWh_H2, 27% of which constitutes only onshore locations. Furthermore, this capacity decreases to 7.3 PWh_H2 with a limitation of 50 km distance from shore. In all cases, Germany has the highest technical storage potential, with a value of 9.4 PWh_H2, located onshore only in salt domes in the north of the country. Moreover, Norway has 7.5 PWh_H2 of storage potential for offshore caverns, which are all located in the subsurface of the North Sea Basin.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

The rural population in the Dry Zone of Sri Lanka is largely affected by Chronic Kidney Disease of Unknown etiology (CKDu). According to the multidisciplinary research carried out so far, quality of groundwater was considered one of the possible causative factors for CKDu. Therefore, the assessment of water quality variations and evolution mechanism of water quality parameters of drinking water sources is important for identifying any relationships between CKDu and the drinking water quality. The current study aimed to perform a detailed hydrogeochemical investigation using isotopic and chemical methods on selected groundwater sources in the CKDu-endemic, non-endemic and control areas. TDS, hardness, Mg2+, Na+ and F- are the main parameters that cause water quality deterioration but, their derived mechanism in these three regions are completely different. The excess concentrations of F- and Mg2+ in the CKDu endemic area, low F- and high Mg2+in the CKDu non-endemic sedimentary formation, and either combinations of low F- and low Mg2+, high F- and low Mg2+ or low F- with high Mg2+ in the control area are the distinct features. The primary processes that regulate the evolution of groundwater types in CKDu endemic and control area is the weathering of silicates. Similarly, in the CKDu endemic area, carbonate dissolution and reverse ion exchange are prominent. Cation exchange and evaporite dissolution are more pronounced in the control area. Shallow groundwaters are evapo-concentrated hence it further deteriorates quality when compared to the deep groundwater with non-mixed, non-evaporated, and higher elevation recharge effect (from 100 m altitude) in the CKDu endemic area. Dilution decreases the ion content in the CKDu endemic area while evaporite dissolution further increase it in the control area after the rainy season. Evaporation, and seawater mixing affected the quality of groundwater in the non-endemic sedimentary formation. A statistically significant difference of F- ionic ratio with Na+, Mg2+, Ca2+ in the endemic and control areas. Intense rock weathering combined with the desorption added excess F- to the groundwater in the CKDu endemic area while the cation exchange and fluorite dissolution is contributing factor in CKDu control area. All the groundwater samples analyzed have exceeded the moderate hardness threshold. However, prominent Mg hardness proportion together with excess F- in the CKDu endemic area may produce nephrotoxic MgF2 complexes that may trigger renal damage. In contrast, produced NaF complexes in the CKDu control area leads to reduction of F- toxicity in the human body. Therefore, increased levels of magnesium, fluoride and TDS in the shallow groundwater, along with geochemical, hydrogeological and climatic factors, may contribute to the CKDu in the Dry Zone of Sri Lanka.

Saline soil from the coast is a valuable resource that is readily available. It is also a valuable resource for reserving arable land. It has been demonstrated that adding organic fertilizers to salinized soils can effectively enhance them. However, since the improvement of saline soils cannot be achieved by a single measure, the effects of compound measures of organic fertilizers combined with mineral elements, humic acid, are significant and might be examined in depth. In order to explore the effects of various measures on the features of pH, electrical conductivity (EC), and nutrient changes in coastal salinized soils in Yancheng, Jiangsu Province, a ryegrass-alfalfa rotation with organic fertilizer as well as compound measures was designed. The findings indicated that the total nitrogen (TN) content of the soil increased and that all organic fertilizer composites decreased the electrical conductivity of the surface soil. However, the organic fertilizer with microbial fertilizer and humic acid was especially effective at regulating the pH and electrical conductivity of the surface soil during the time when salts were prone to accumulating. In conclusion, our findings point to new approaches to lowering salinity and boosting fertility in coastal saline soils: organic fertilizer with microbial fertilizers and humic acid, as well as organic fertilizer with Attapulgite clay.

The production of plants and crops is influenced by environmental stress, which is a serious scientific issue. Cotton is an essential crop for producing natural fibers that are used to make biofuel and edible oils. Salinity is the main element that influences cotton growth during the beginning of germination. The type of salt and the growth stage affects how sensitive a plant is to salt stress. Developing ways to enhance cotton performance in salty circumstances can be aided by an understanding of the response of cotton to salt, its mechanism of resistance, and its management methods. Osmotic and ionic imbalances originate due to the deposition of soluble salts under salinity stress in the plant's root zone. Soil salinity significantly reduces plant growth due to several factors, such as nutritional ion imbalance, which reduces K+, PO4-, and NO- absorption, excessive salt chloride concentrations, and osmotic stress, which hinders water availability. Research has revealed that compared to subsequent stages, the germination, emergence, and seedling phases are more vulnerable to salinity stress, which ultimately affects the seed cotton yield by delaying blooming, reducing fruiting positions, shedding fewer fruits, and reducing boll weight. The morphology, growth of cotton roots, shoots, yield, and fiber quality are all strongly impacted by salinity stress. It slows down plant feeding, cellular metabolism, and photosynthesis. The soil, water, and climate all affect how the plant responds to salinity stress. During salt stress, excessive exclusion of sodium or its compartmentalization is the key adaptation process in cotton. A major adaptive potential to create cotton types that can withstand salt is provided by the up-regulation of both physicochemical and non-enzymatic antioxidant genes. A successful strategy to increase cotton germination in saline soils is seed priming. Moreover, the transgenic strategy might be a viable choice for improving cotton yield in saline environments. Our review focuses on the impacts of salinity on cotton productivity as well as how plants react to salt stress. It also clarifies recent genetic advancements and molecular breeding for cotton's resistance to soil salt. To create salt-tolerant cultivars, a combination of traditional breeding and novel molecular approaches will be useful.

Lettuce is a salt-sensitive crop and has a threshold electrical conductivity of 1.3–2.0 mS cm-1 and above that is considered detrimental. As there has been very little information on the physio-logical response of different critical stages of lettuce under different salt stress (SS), the current study is focused on investigating the effects of SS on the critical physiological traits influencing the carbon assimilation in different growth stages of lettuce. The experiment was conducted in deep-water culture hydroponic system in a greenhouse condition. Four levels of sodium chloride salt treatments (EC: 20, 16, 8, and 1.8 mS cm-1) were applied. During both growth stages (day 11 (GS1) and day 19 (GS2) after salt treatment), the leaf transpiration rate, stomatal conductance, and intercellular CO2 were severely decreased. However, the carbon assimilation rate remained unchanged under SS. Similarly, the water use efficiency increased under the SS. It is concluded that the increasing SS increased stomatal and non-stomatal limiting factors during GS1 suggesting the enhanced limitation in photosynthetic activity while no such trend was observed during GS2. The decreased gm with increased SS at GS1 and GS2 suggested that SS induced the irreversible decrease of gm, which in turn can be responsible for the transient reduction in the Vcmax and Jmax during GS2. Taken together, the evidence from this research recommends that varying the SS levels can significantly affect the physiological performance of lettuce at both growth stages.

Excess salt and inadequate potassium intakes are associated with high cardiovascular disease (CVD). In Montenegro, CVD is the leading cause of death and disability. There is no survey that has directly measured salt and potassium consumption in Montenegro. The aim is to estimate population salt and potassium intakes and explore knowledge, attitudes and behaviour (KAB), amongst the adult population of Podgorica. Random samples of adults were obtained from primary care centres. Participants attended a screening including demographic, anthropometric and physical measurements. Dietary salt and potassium intakes were assessed by 24h urinary sodium (UNa) and potassium (UK) excretions. Creatinine was measured. KAB was collected by questionnaire. Six hundred and thirty-nine (285 men, 25-65 years) were included in the analysis (response rate 63%). Mean UNa was 186.5 (SD 90.3) mmol/day, equivalent to 11.6g of salt/day, and potassium excretion 62.5 (26.2) mmol/day, equivalent to 3.2g/day. Only 7% of them had a salt intake below the WHO recommended target of 5g/day, and 13% ate enough potassium (>90 mmol/day). The majority (86%) knew that high salt causes ill-health. However, only 44% thought it would be useful to reduce consumption. Salt consumption is high, and potassium consumption is low, in men and women living in Podgorica.

The use of salt rock for underground radioactive waste disposal facilities requires a comprehensive analysis of creep-damage process in salt rock. A computer-controlled creep setup is employed to carry out a creep test of salt rock lasted as long as 359 days under a constant uniaxial stress. The AE space-time evolution and energy releasing characteristics during creep test are studied in the meantime. A new creep-damage model is proposed on the basis of fractional derivative by combining the AE statistical regularity. It indicates that the AE data in non-decay creep process of salt rock can be divided into three stages. Furthermore, the parameters of new creep-damage model are determined by Quasi-Newton method. The fitting analysis suggests that the creep-damage model based on fractional derivative in this paper provides a precise description of full creep regions in salt rock.

Crossostephium chinense is a wild species with strong salt tolerance, which has great potential to improve the salt tolerance of cultivated chrysanthemums. Conversely, the unique salt-tolerant molecular mechanisms of Cr. chinense are still unclear. This study performed a comparative physiological and transcriptome analysis of Cr. chinense, Chrysanthemum lavandulifolium and their hybrids. The physiological results showed that Cr. chinense maintained a higher superoxide dismutase (SOD) activity, to alleviate the oxidative damage to membrane. KEGG enrichment analysis showed that the plant hormone signaling transduction and the MAPK signaling pathway were mostly enriched in Cr. chinense and hybrids under salt stress. Further weighted gene co-expression network analysis (WGCNA) of DEGs suggested that the abscisic acid (ABA) signaling transduction may play a significant role in the salt-tolerant mechanisms of Cr. chinense and hybrids. The tissue-specific expression patterns of the candidate genes related to ABA signaling transduction and MAPK signaling pathway indicated that genes related to ABA signaling transduction performed significant expression levels under salt stress. This study provides a theoretical foundation for future research into the molecular mechanism of salt tolerance in chrysanthemums under salt stress.

Abstract: This study observes the characteristics and influencing factors of carbon fluxes of the Momoge salt marsh ecosystem over four years, which behaves as a CO2 sink. The daily, seasonal, and interannual variations of CO2 fluxes in the Momoge salt marshes were observed using the eddy covariance method and compared with various environmental factors. An overall daily “U” shaped distribution was observed, with uptake during the day (negative values) and release at night (positive values). Annually, the carbon fluxes in the study area roughly exhibit a “V” shape. Carbon fluxes during the non-growing season predominantly showed positive values, indicating the release of CO2 into the atmosphere. Photosynthetically active radiation was the primary influencing factor affecting hourly and daytime variations in net ecosystem exchange (NEE) during the growing season, while temperature was the main factor influencing nighttime NEE dynamics. Air temperature, soil temperature, photosynthetically active radiation, precipitation, and water level all had significant impacts on daily net CO2 exchange. At the monthly scale, larger values of soil temperature, air temperature, photosynthetically active radiation, and aboveground biomass correspond to a stronger carbon absorption capacity of the ecosystem. Overall, temperature remains the primary factor for carbon fluxes in the Momoge wetlands.

Drought and salinity are among the most important abiotic stress factors that limit the productivity in economically important plants. Although genes from wild relatives or unadapted germplasm have often been used for stress tolerance breeding, only few studies have examined wild relatives to understand the genetic and molecular basis of stress tolerance. In this study, we monitored the changes in gene expression profiles of leaf and root tissues of two wild barleys (Hordeum spontaneum L.) accessions from Israel after treatment with salt (NaCl) and drought (PEG) stress. We identified a total of 641 differentially expressed genes across 24 conditions (2 accessions, 2 stress conditions, 2 tissues and 3 time points). Our gene expression analyses revealed large numbers of differentially expressed genes in different accessions by different stress treatments. In addition, the number of genes altered in the leaves of stress-exposed plants of both genotypes was higher than those altered in the roots. Interestingly, there was a relatively little overlap between the leaf and the root stress-responsive gene expression patterns, suggesting that different stress-associated processes might be operating in these tissues during stress adaptation. Overall, our results revealed a number of candidate genes and plant processes associated with stress tolerance in wild barley. Wild barley would be a useful source of new genetic variation for drought and salt stress tolerance. Our results could provide new insights into the mechanisms of drought and salt stress tolerance in wild barley and should be useful for genetic improvement of salt-drought tolerance in cultivated barley.

During their growth, bacteria respond to complex environmental changes through equally com-plex and orderly regulatory mechanisms. sRNA has an important role as a post-transcriptional regulator in the environmental adaptation of Bacillus. In this study, we identified an sRNA Bvs091 located in the intergenic region of the Bacillus velezensis, which is widely present in the genus Bacillus and whose expression is upregulated by salt treatment. The deletion of bvs091 in B. ve-lezensis PEBA20 led to a reduced growth rate and a change in the phenotypes, with simple colony structures and low and easily degradable biofilm. Salt tolerance tests indicated that the deletion of bvs091 results in a reduced salt tolerance. galT2 mRNA is supposed to be a direct target of Bvs091 according to results obtained by using the bioinformatic method and performing qRT-PCR analysis. The microscale thermophoresis (MST) analysis showed that Bvs091 could directly bind 28‒51 bases in front of the promoter of galT2. Subsequently, the deletion of galT2 in B. velezensis resulted in increased salt tolerance. Based on the techniques of double plasmids and a half-life period, sRNA Bvs091 is confirmed as a trans-encoded sRNA that negatively regulates the mRNA expression of galT2. In brief, the trans-encoded sRNA Bvs091 acts by pairing the incomplete complementary bases of galT2 mRNA, reducing galT2 mRNA’s stability and affecting the trans-lation efficiency.

Seed germination is the most sensitive stage to abiotic stress, including salt stress (SS). SS affects plant growth and performance through ion toxicity, decreases seed germination percentage, and increases the germination time. Several priming treatments were used to enhance germination under SS. The objectives of this study are to 1) identify priming treatments to shorten the emergence period; 2) evaluate priming treatments against the SS; 3) induce synchronized seed germination. Salt-sensitive “Burpee bibb’ lettuce seeds were treated with 0.05% Potassium nitrate, 3 mM Gibberellic acid, and distilled water (HP). All the primed and non-primed seeds were subjected to 100 mM NaCl or 0 mM NaCl. The 7-day experiment arranged in a complete randomized block design with four replications was conducted in a growth chamber maintained with 16/8 h photoperiod (light/dark), 60% relative humidity, and day/night temperature of 22/18 °C. The result indicated that HP seeds were better synchronized under SS. Similarly, FM and DM of cotyledon, hypocotyl, and radicle were highest in HP lettuce regardless of SS. Electrolyte leakage was the lowest in the HP lettuce, while other priming methods under SS increased membrane permeability leading to osmotic stress and tissue damage. Overall, the HP can be a suitable priming method to synchronize germination and increase FM and DM by creating the least osmotic stress and ion toxicity in lettuce under SS.

Silver in different forms is used for medical purposes from ancient times. It is not yet well known, which form of silver is more biocompatible and less toxic. Here we considered silver nanoparticles and silver citrate. Also, the relationships of neurotoxicity of silver compaunds with ageing factor is not yet described. To assess the role of nanoform in neurotoxicity of silver and role of ageing a long-term experiment was conducted. We had four control groups of intact mice and four experimental groups which were exposed to silver nanoparticles and silver citrate for two months. Four groups of mice were introduced into the experiment since the age of five months to assess ageing factors. It was shown that the nanoform does play a certain role in neurotoxicity of silver. Silver citrate seems to be a more preferable silver compound. Ageing can be regarded as a positive factor that neutralizes toxic action of silver compounds. It may be due to the development of physiological/cognitive functions with the age as well as adaptation to unnatural content in the individual cages that is definitely stressful for mice.

According to WHO, reducing salt intake to less than 5 g/day means less death, disability, and suffering from heart disease and stroke, with around 1.89 million lives saved every year. In this scoping review, we have reviewed the salt consumption pattern of South Asia. For this purpose, we searched online databases and websites and consulted key informants to address relevant unpublished reports. The inclusion criteria are English-language publications between January 2011 and October 2021, as well as research that evaluated salt intake in the South Asian region and reported salt/sodium 24-hr urine or spot urine samples involving at least 100 participants. A total of 2043 studies were screened, out of which 12 studies fulfilled all the criteria. Our review revealed that reported salt intake in the South Asian region ranges from 6.7-13.3 g/day, which was higher than the WHO-recommended maximum level of 5 g/day in all countries. Men consumed more salt than women. This review demonstrates the critical importance of implementing a salt reduction program in South Asian countries.

How to improve plant tolerance and yield under salt stress is critical for ensuring sufficient food supply since plant survival and agricultural productivity are both affected by salinity. Some evidence has showed that beneficial microorganisms have a high ability to improve plant salt tolerance and increase crop yield. But few studies were involved in effects of halotolerant yeasts on plants under salt stress. In this present research, Meyerozyma guilliermondii, a halotolerant yeast, was inoculated with tomato plants followed by salt treatment of four different NaCl concentrations (0, 100, 200, and 300 mM). Our results showed that inoculation of M. guilliermondii increased the chlorophyll biosynthesis and photosynthetic machinery effectiveness under salt stress, contributing to biomass accumulation. Under salt treatment of 300 mM NaCl, the yeast inoculation significantly increased ascorbate concentrations in leaves, yet showed no effects on levels of glutathione and proline. Antioxidant enzymes were affected differently by the yeast inoculation. It was found that the yeast inoculation increased superoxide dismutase (SOD), catalase (CAT), and peroxidase (POD) activities under 300, 100, and 200 mM NaCl, respectively. Total soluble sugar levels increased in inoculated tomato plant leaves; however, there were no significant differences between different NaCl concentrations. Under 300 mM NaCl, the yeast inoculation significantly decreased H2O2 levels and reduced malondialdehyde levels. All together, our results showed that halotolerant yeast M. guilliermondii inoculation might be a strong candidate for regulating tomato growth under salt stress by increasing ability to scavenge reactive oxygen species and chlorophyll intactness, and by strengthening photosynthetic machinery.

Salinity is the most significant abiotic stress affecting crop yield worldwide, breeders are Salinity is the most important abiotic stress limiting crop production throughout the world, and breeders are encouraged to test novel genotypes for their resistance to this selection agent. However, getting a sufficient number of plants for the evaluation can be a lengthy and time-consuming procedure that might be shortened by applying in vitro techniques. An experiment was conducted under controlled saline circumstances using a tissue culture technique to investigate the influence of salt on several physic-biochemical parameters. Micro-shoots of Volkamariana lemon, sour orange, trifoliate orange, and Cleopatra mandarin rootstocks were re-cultured on MS media supplemented with NaCl from 25, up to 150 mM. Following the experiments, all of the tested rootstocks' morphological and biochemical characteristics, stomata behavior, and element accumulation were measured. As a result, adding NaCl from 25 to 150 mM to MS media caused a reduction in all morphogenetic parameters such as shoot number, shoot length, leaves number, and survival percentage was measured compared with control. Photosynthesis pigment, RWC, K, and Ca ions were decreased by increasing NaCl from 100 to 150 mM. On the contrary, proline, Cl, and Na were increased. Cleopatra mandarin and Trifoliate orange are more tolerant to salt stress than Volkamariana lemon and sour orange citrus.

Common bean (Phaseolus vulgaris L.) is an important crop for food security and for national economics for several countries worlwide. One of the most important factors of risk in common bean production is the fungal disease anthracnose caused by Colletotrichum lindemuthianum, which in some cases, causes complete yield losses; this kind of plant disease is usually managed through the application of chemical products such as fungicides, that are commonly not accepted by society, this rejection is based on the relationship of pesticides with health damage and environmental contamination. In order to help in solving this drawbacks, the present work propose the use of Electrochemically Activated Salt Solutions(EASS) as a safer pathogen control agent in crops due to it have shown an elicitor and biostimulant effect on plants such as tobacco and apple. With this background, this manuscript presented in vitro results of the evaluation of the inhibitory effect for multiple bean pathogens and in vivo results of EASS in the common bean-Colletotrichum pathosystem by in vitro evaluations of the inhibitory effect for multiple bean pathogens and in vivo evaluation of the infection severity and defense activation such as secondary metabolites production and antioxidant activity. EASS presence in growth media had strong inhibitory effect, at beginning of experiment, for some of the evaluated fungi. EASS showed effect against the development of the disease when applied in specific doses to prevent distress in plants.

Microalgae biomass is considered a promising alternative feedstock for biodiesel production due to its high productivity of neutral lipids, specially under abiotic stress conditions. Among the unicellular microalgae that show this characteristic, Chlamydomonas reinhardtii appears as one of the most important model species that have increased lipids production under abiotic stress conditions. In this study, we show that cells cultivated under mixotrophic condition supplemented with 0.1 M of NaCl rapidly raises their amount of neutral lipids in C. reinhardtii without reduction of their cellular growth rate, being therefore a promising condition for biomass towards bioenergy production. The nuclear proteome of these cells was investigated where we identified 323 proteins with an enrichment of almost 60% of nuclear proteins in the total dataset. We found 61 proteins differentially regulated upon salt treatment, including proteins annotated in functional categories related to translation and nucleosome assembly functions, among others. Additionally, we identified Transcription factor proteins (TFs) and analyzed their likely Transcription factors-binding regulatory elements identifying target genes related to lipids metabolism and kinase functions, indicating possible regulatory pathways of lipids biosynthesis. Together these data can help understand regulatory nuclear mechanisms leading to an increase of lipids in the first 24h of salt stress 0.1M NaCl.

A lignin modified salt resistance branched high-performance water reducer was prepared via free radical polymerization. The water reducing agent was identified through Fourier transform infrared analysis, thermal gravimetric analysis, and scanning electron microscopy. The experiment conducted on cement paste demonstrates that the water-reducing efficiency can reach a maximum of 44%. Additionally, the significant spatial steric hindrance of the application enhances the dispersal capability of the water-reducing agent, resulting in effective water reduction and reduced viscosity. In addition, its compressive strength is the highest after 3-day curing and 3, 7, 28-day standard curing, and it has the best overall performance both in water and saline water prepared systems.The application in oil cement slurry shows that it exhibits good dispersibility in fresh water, saline water, and substitute ocean water. In the Halfaya and Missan Oilfields of Iraq, BHPWR was used in slurry with a density of 2.28g cm-3 for casing the 244.5 mm salt paste layer of five wells. Cementing results exceeded expectations with over 85% excellent and 100% qualified.

Salinity is a significant abiotic stress factor for ornamental plants cultivated in greenhouses, as they are supplied with fertilizers over a long period of time. It causes drastic yield losses in com-mercially important ornamentals such as Gerbera jamesonii, whose cut flowers rank fifth in the global flower trade. In the current study, pretreatment of G. jamesonii plants (white and yellow flowering varieties) with optimum concentrations of thiourea (1.0 mM, 5.0 mM & 10.0 mM) in-duced plant salt-tolerance. Gerberas pretreated with thiourea (5.0 mM), when exposed to NaCl (200mM), showed no signs of plant stress or phenotypic abnormalities, as seen in gerberas ex-posed to NaCl without thiourea pretreatment. Moreover, thiourea application significantly pro-moted plant growth as evidenced by increases in fresh and dry leaf weight, relative water con-tent, total protein content, free proline content, and chlorophyll. A decrease in H2O2 and MDA content and an increase in antioxidant enzymes superoxide dismutase, catalase, ascorbate perox-idase, glutathione reductase, and peroxidase activity indicate minimal cellular damage in gerberas treated with thiourea. Thus, spraying leaves with thiourea (5.0 mM) could help gerbera plants overcome the deleterious effects of salt stress during repeated fertilization in nethouses. In addi-tion to alleviating salt stress, thiourea can also be used as a biofertilizer. This could also be ex-tended to other ornamental species to promote sustainable development of the floriculture indus-try.

Although 4Ce4YSZ has high corrosion resistance, it faces challenges concerning sinterability and ionic conductivity. Therefore, we studied destabilization behavior caused by corrosion and oxygen vacancy ordering according to ZnO doping. The powders of (4Ce4YSZ)1-x(ZnO)x (x=0.5, 1, 2, 4 mol%) were synthesized through the sol-gel method. With the addition of ZnO, the cubic phase increased, and secondary phases were not observed. The (111) peak showed a higher angle shift in ZnO-doped 4Ce4YSZ compared to 4Ce4YSZ, and TEM-SAED revealed a reduction in the spacing of the (011)t plane, suggesting lattice contraction due to the substitution of the smaller Zn2+ (60 Å) for Zr4+ (84 Å) in the lattice. The local atomic structure analysis was conducted using EXAFS to investigate the oxygen vacancy ordering behavior. Zr K-edge Fourier-transform data revealed a decrease in the Zr-O1 peak intensity with an increasing amount o ZnO doping, indicating an increase in oxygen vacancies. The Zr-O1 peak position shifted to the right, leading to an increase in the Zr-O1 interatomic distance. In the Y K-edge Fourier-transform data, the Y-O1 peak intensity did not decrease, and there was little variation in the Y-O1 interatomic distance. These results suggest that the oxygen vacancies formed due to ZnO doping are located in the neighboring oxygen shell of Zn, rather than in the neighboring oxygen shells of Y and Zr. Impedance measurements were conducted to measure the conductivity, and as the amount of ZnO doping increased, the total conductivity increased, while the activation energy decreased. The increase in oxygen vacancies by ZnO doping contributed to the enhancement of conductivity and it is considered that these created oxygen vacancies did not interact with Zn2+ and did not form defect associations. Fluoride-based molten salts were introduced to the specimens to assess corrosion behavior in a molten salt environment. Yttrium depletion layers (YDLs) were formed on the surfaces of all specimens due to the leaching of yttrium. However, Ce remained relatively stable at the interface according to EDS line scans, suggesting a reduction in the phase transformation (cubic, tetragonal to monoclinic) typically associated with yttrium leaching in YSZ.

This study chose the indoor soil column test as the main method and the field test as the validation test to investigate the effects of various straw mulching techniques (surface, deep and straw mulching + deep burial) on evaporation and salt dynamics in saline soils. The results showed that straw mulching treatment could effectively reduce soil water evaporation, promote desalination in the stage of leaching infiltration and alleviate salt return in the stage of water evaporation, and the effect of straw mulching + deep burial treatment was better than that of single-layer straw mulching treatment. The indoor soil column test showed that S2D1 treatment (a 2:1 ratio of soil surface cover to the amount of straw buried 40cm below the soil surface) had the best effect on the suppression of soil moisture evaporation, and the cumulative evaporation of soil moisture was reduced by 65.85% compared with that of the CK, and the rate of salinity return in the evaporation stage was effectively reduced by 92.04% compared with that of the CK. In addition, there is a significant positive correlation between cumulative evaporation of soil moisture and cumulative soil salinity, which implies that cumulative soil salinity increases with cu-mulative evaporation of soil moisture. The results of the field experiment were consistent with the soil column test, and the S2D1 treatment was able to maintain high soil moisture content in all soil layers in all periods of the experiment and kept soil salinity in the 0-40 cm soil layer at a low level. However, in the 40-80 cm soil layer, the soil salinity suppression effect of DB treatment (straw buried at 40 cm below soil surface) was the best. So in summary, the S2D1 treatment had the best salinity and evapo-transpiration suppression effect in saline soils. This study is of great significance for the resource uti-lization of straw waste, improvement of water utilization and efficiency, and soil salinization manage-ment.

High salinity in soil affects the normal growth and development of crop. MicroRNA171 (miR171) plays a momentous role in plant resistance to adversity stress. The functions of Sly-miR171d and Sly-miR171e on growth of tomato and fruit nutritional quality under salt stress were studied. The results showed that the seed germination and seedling growth of tomato that silencing of Sly-miR171d/e by short tandem target mimic (STTM) were better than those of wild-type (WT). Silencing of Sly-miR171d/e seeds maintained a high germination rate, while WT tomato seeds barely germinated under 50 mM NaCl stress. Under 100 mM NaCl stress, silencing of Sly-miR171d/e increased the expression of their target gene SlGRAS24 with increasing duration of salt stress, while they enhanced the antioxidant activity, reduced reactive oxygen species (ROS) accumulation, and enhanced the salt tolerance of tomato plant by regulating gibberellin (GA) level. Moreover, the preharvest and postharvest fruit nutritional quality under salt stress was also studied, and the results showed that silencing of Sly-miR171d/e increased soluble solids, lycopene, total carotenoids, Vitamin C, organic acids and phenolic substances in tomato fruit. The present study demonstrated that silencing of Sly-miR171d/e enhanced plant salt tolerance through the GA pathway, and improved fruit nutritional quality under salt stress.

The TGACG motif-binding factor1 (TGA1) transcription factor, a significant protein in the bZIP transcription factor family, exhibits a myriad of functions, contributes to numerous biological events, and holds substantial application potential. In this study, our analysis revealed a diverse range of photoregulatory and hormone regulatory elements within the MtTGA1 promoter region. The expression profile of MtTGA1 indicated its highest expression in the root, with its regulation influenced by SA, ABA, BR, and GA. Under salt stress conditions, transgenic plants demonstrated significantly longer root lengths and heightened activities of antioxidant enzymes such as ascorbic acid catalase (APX), peroxidase (POD), catalase (CAT), and superoxide dismutase (SOD) in their roots and leaves compared to control plants. Simultaneously, the levels of endogenous hormones ABA and BR escalated in transgenic plants, with a marked change in the morphology of their leaf cells. Transcriptome analysis identified a total of 193 differentially expressed genes, implicating a wide array of biological processes. Furthermore, we found that MtTGA1 is able to interact with Medicago truncatula SPX domain containing protein 1 (SPX1). In conclusion, the MtTGA1 transcription factor plays a crucial role in enhancing salt tolerance, which provides new insights for improving plant survival under salt stress conditions.

Sweet sorghum is an important bioenergy grass and valuable forage with a strong adaptability to saline environments. However, little is known about the mechanisms of sweet sorghum coping with ion toxicity under salt stresses. Here, we first evaluated the salt tolerance of a sweet sorghum cultivar “Lvjuren” and determined its ion accumulation traits under NaCl treatments; then explored key genes involved in Na+, Cl−, K+ and NO3− transport using transcriptome profiling and qRT-PCR method. The results showed that the growth and photosynthesis of sweet sorghum were unaffected by 50 and 100 mM NaCl treatments, indicative of a strong tolerance of this species to salt stresses. Under NaCl treatments, sweet sorghum could efficiently exclude Na+ from shoots and accumulate Cl− in leaf sheaths to avoid their overaccumulation in leaf blades; meanwhile, it possessed a prominent ability to sustain NO3− homeostasis in leaf blades. Transcriptome profiling identified several differentially expressed genes associated with Na+, Cl−, K+ and NO3− transport in roots, leaf sheaths and leaf blades of sweet sorghum after 200 mM NaCl treatment for 6 and 48 h. Moreover, transcriptome data and qRT-PCR results indicated that HKT1;5, CLCc and NPF7.3-1 should be key genes involved in Na+ retention in roots, Cl− accumulation in leaf sheaths and maintenance of NO3− homeostasis in leaf blades, respectively. Many TFs were also identified after NaCl treatment, which should play important regulatory roles in salt tolerance of sweet sorghum. This work lays a preliminary foundation for clarifying the molecular basis underlying the adaptation of sweet sorghum to adverse environments.

In this work, the adsorption and photocatalytic properties of ZnO-ZnAl2O4 nanosized composites synthesized by the polymer-salt method have been studied. To evaluate the efficiency of adsorption, experiments were carried out on the decolorization of aqueous solutions of the Chicago Sky Blue diazo dye. The adsorption process is divided into two stages, at the first stage the dye is rapidly adsorbed on the outer surface of the composite particles, at the second stage the dye diffuses into the pores of the material. It was noted that the rate of photocatalytic decomposition of the dye is higher than the rate of the adsorption process, which indicates the occurrence of photocatalytic decomposition of dye molecules both on the surface of the composites and in the liquid phase. With an increase in the light intensity, the photocatalytic process is significantly accelerated, linearly at low intensities, and at high intensities the dependence becomes a power law.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

Salinity substantially affects plant growth and crop productivity worldwide. Plants adopt several biochemical mechanisms including regulation of antioxidant biosynthesis to protect themselves against the toxic effects induced by the stress. One-year-old Pistachio rootstock exhibiting different degrees of salinity tolerance were subjected to sodium chloride induced salt stress to identify genetic diversity among cultivated pistachio rootstock for their antioxidant responses, and to determine the correlation of these enzymes to salinity stress. Leaves and roots were harvested following NaCl-induced stress. Results show that a higher concentration of NaCl treatment induced oxidative stress in the leaf tissue and to a lesser extent in the roots. Both tissues showed an increase in ascorbate peroxidase, superoxide dismutase, catalase, glutathione reductase, peroxidase and malondialdehyde. Responses of antioxidant enzymes were cultivar dependent, as well as temporal and dependent on the salinity level. Linear and quadratic regression model analysis revealed significant correlation of enzyme activities to salinity treatment in both tissues. The variation in salinity tolerance reflected their capabilities in orchestrating antioxidant enzymes at the roots and harmonized across the cell membranes of the leaves. The study provides a better understanding of root and leaf coordination in regulating the antioxidant enzymes to NaCl induced oxidative stress.

The consumer’s acceptability of hamburgers elaborated with the flank of culling cows in which the content of salt or fat had been partially replaced was studied. A mixture of potassium chloride, potassium ferrocyanide and sodium ferrocyanide was used as substitutes for the salt. Oat flakes or a mixture of chia and flax seeds were used as substitutes for the fat. The hamburgers were tasted by 34 consumers. Consumers did not detect significant differences between the control and the rest of the formulations. Neither the gender nor the age of the consumers influenced the sensory appraisal. However, many comments regarding texture failures were recorded. Therefore, the substitution of salt and / or fat in the composition of hamburgers made with the flank of cows is a viable alternative for the commercialization of these pieces of low commercial value as long as the texture of the same is adjusted to resemble it to the control.

The study aimed to investigate the effects of colonization with two arbuscular mycorrhizal (AM) fungi, Funneliformis mosseae , Diversispora versiformis , alone and in combination on the growth and nutrient acquisition of NaCl-stressed Chrysanthemum morifolium (Hangbaiju) plants in the greenhouse experiment. Mycorrhizal and non-mycorrhizal Hangbaiju plants were grown under different salinity levels imposed by 0, 50 and 200 mM NaCl for five months, following 6 weeks of non-saline pre-treatment. The results showed that root length, shoot and root dry weight, total dry weight, shoot and root N concentration were higher in mycorrhizal than in non-mycorrhizal plants under moderate saline conditions especially with D. versiformis colonization. As salinity increased, the mycorrhizal colonization, the mycorrhizal dependence (MD) decreased. Enhancement of tissue N acquisition is probably the main mechanism underlying salt tolerance in AM plants. It is suggested that the symbiotic associations between D. versiformis fungus and C. morifolium plants may be taken as a biotechnological practice in culture.

In this paper the influence of austempering temperature and salt bath agitation on the final microstructure and mechanical properties of the ferritic ductile iron were studied. 17 samples had been subjected to different heat treatment parameters. Different microstructures were recorded upon the completion of the tests. From the obtained micro images, it is obvious that both the austempering temperature and salt bath agitation affect the final microstructure of the austempered ductile iron. Lower austempering temperatures and salt bath agitation produce more ausferrite in the microstructure, hence the harder and tougher phases are present. This was confirmed with hardness and toughness test of the 17 heat-treated samples. Lower austempering temperatures give more ausferrite phase and therefore higher hardness, but hardness decreases with increasing austempering temperatures. Toughness rises with rising austempering temperatures, but drops significantly with temperatures above 395°C because of the final microstructure.

Soil salinity is seen as a major restriction for crop production, and with water scarcity this problem becomes more complicated. Mulching is crucial to salinity dynamics management by decreasing evaporation with improving the soil’s characteristics. Using chitosan as an eco-friendly biostimulant can enhance plant defense genes during different abiotic stresses. Recently, agricultural research has recognized nanoparticles as a pioneer material due to their distinctive physicochemical features. Therefore, a lysimeter experiment was conducted to investigate the interactive effects of mulching (UNM: un-mulched, WPM: white plastic, RSM: rice straw and SDM: sawdust) and chitosan foliar application (Ch0: control, Ch1: 250 mg chitosan L-1, Ch2: 125 mg nano chitosan L-1, and Ch3: 62.5 mg nano chitosan L-1) on the biochemical soil characteristics and common beans productivity under salt affected soil conditions. Organic mulching (RSM and SDM) treatments significantly improved the soil's organic carbon, available nutrient content, and total count of bacteria. WPM treatment lowered soil EC to 6.63 dS m-1 and increased soil water content to 34.13%. The application of Ch3 caused considerable increases in the plant height, shoot dry weight, root dry weight, grain yield, and nutrient content in the seed. The total fungi count in the soil and Na% in the seed was significantly decreased due to chitosan foliar applications. Moreover, the interactive effect of different mulch materials plus foliar by chitosan applications gave a statistically similar seed yield in both seasons. Overall, this study revealed the potential of the mulching treatments and foliar application of nano chitosan in improved biochemical soil characteristics and common bean productivity under saline soil conditions.

Petrosamine (1) – a colored pyridoacridine alkaloid from the Belizean sponge, Petrosia sp. that is also a potent inhibitor of acetylcholine esterase (AChE) – was investigated by spectroscopic and computational methods. Analysis of the petrosamine free energy landscapes, pKa and tautomerism revealed an accurate electronic depiction of the molecular structure of 1 as the di-keto form, with net charge of q = +1, rather than a dication (q = +2) under ambient conditions of isolation-purification. The pronounced solvatochromism (UV-vis) reported for 1, and related analogs, was investigated in detail and is best explained by charge delocalization and stabilization of the ground state (HOMO) of 1 rather than an equilibrium of competing tautomers. Refinement of the molecular structure of 1 by QM methods complements published computational docking studies to define the contact points in the enzyme active site that may improve design of new AChE inhibitors based on the pyridoacridine alkaloid molecular skeleton.

To investigate the effect of prohexadione-calcium (Pro-Ca) primed on seed germination and seedling growth of oilseed rape under salt stress, to alleviate the inhibition of soil salinization on the growth of oilseed rape, and to improve the sustainability of agricultural production. Using Huayouza 158R and Huayouza 62 as test materials, the regulation of seed germination and seedling growth under the stresses of 0, 100, and 150 mM NaCl (S0, S100, and S150) was investigated after the primed of Pro-Ca. We conducted six treatments, S0: non-primed + 0 mM NaCl, PCS0: Pro-Ca primed + 0 mM NaCl, S100: non-primed + 100 mM NaCl, PCS100: Pro-Ca primed + 100 mM NaCl, S150: non-primed + 150mM NaCl, Pro-Ca+S150: Pro-Ca primed + 150 mM NaCl. The results showed that salt stress inhibited seed germination and seedling growth, and Pro-Ca primed significantly increased the germination index and vigor index of oilseed rape seeds. The average germination time and malondialdehyde (MDA) content were significantly reduced, which resulted in the optimal initiation fiddling concentration of 8mg·L-1. The morphological parameters of oilseed rape decreased significantly under salt stress, with leaf area decreasing by 70.69% and 75.03% and total chlorophyll content decreasing by 18.55% and 18.68% at S150. With the rise of salt stress, the changes of each photosynthetic parameter were somewhat similar, and Pn, Gs, Ci, and Tr continued to decline, indicating that the effects of salt stress on photosynthesis in oilseed rape might be mainly attributed to stomatal restriction and inhibition of photosynthetic pigment synthesis. While Na+ and MDA contents increased significantly, reaching a peak at S150, indicating that Na+ content increased significantly under salt stress, which resulted in the slow growth of oilseed rape and weak plants under the influence of Na+ salt damage. After Pro-Ca primed, leaf area and photosynthetic pigment synthesis increased, and the initiation treatment promoted the rise of Pn, Gs, Ci, and Tr under salt stress. The Na+ content decreased by 7.29% and 6.96% in PCS100 compared with S100, decreased by 9.23% and 25.02% in PCS150 compared with S150, and increased in K+ and Mg2+ after Pro-Ca primed. At this time, the antioxidant enzyme activities increased, and the MDA content and relative conductivity decreased. It was concluded that Pro-Ca primed improved the photosynthetic capacity of oilseed rape by promoting leaf growth, stomatal opening, and photosynthetic pigment synthesis. At the same time, reducing Na+ content and promoting K+ and Mg2+ absorption and antioxidant enzyme activities together alleviate salt damage and improve salt tolerance of oilseed rape.

The linkage between the salt wedge, tidal patterns, and the Magdalena River discharge is established by assessing the ensuing parameters: stratification (ϵ), buoyancy frequency (β), potential energy anomaly (φ), Richardson number (RL), and bottom turbulent energy production (P). The salinity, temperature, density, and water velocity data utilized were derived from MOHID 3D, a previously tailored and validated model for the Magdalena River Estuary. To grasp the dynamics of the river, a flow regime analysis was conducted during both wet and dry climatic seasons of the Colombian Caribbean. The utilization of this model aimed to delineate the estuary's spatial reach, considering flow rates spanning from 2000 to 6500 m³/s across two tidal cycles. This approach facilitates the prediction of the position, stability, and stratification degree of the salt front. Among the conclusions drawn, it is highlighted that: 1. The river flow serves as the principal conditioning agent for the system, inducing a strong estuary response to weather stations; 2. The extent of wedge intrusion and the river discharge exhibit a non-linear, inversely correlation; 3. Tidal waves cause differences of up to 1000 m in the horizontal extent of the wedge; 4. Widespread channel erosion occurs during the rainy season when the salt intrusion does not exceed 2 km; 5. Flocculation processes intensify during the transition between dry and wet seasons; 6. The stability of the salt layering and the consolidation of the FSI-TMZ are contingent upon the geometric attributes of the channel.

In order to understand the response mechanism between plant stress, physiological indicators and hyperspectral indices, pot experiments were conducted on Suaeda salsa seedlings collected from a coastal wetland area to reveal the effects of salt stress on the physiological indicators and reflectance spectra of Suaeda salsa at the canopy and leaf level. The Suaeda salsa seedlings were exposed to seven salt treatments of different concentrations (0 mmol/L (control), 50 mmol/L, 100 mmol/L, 200 mmol/L, 300 mmol/L, 400 mmol/L, and 600 mmol/L) in natural conditions. The physiological indicators of plant height, fresh weight, dry weight, leaf succulence, chlorophyll content, and carotenoid content were measured, in addition to the reflectance spectra of Suaeda salsa at both the canopy and leaf level. Firstly, the effects of salt stress on the physiological indicators and reflectance spectra were analyzed by the qualitative and quantitative methods. Then, physiological indicators sensitive to salt stress were further retrieved. Afterwards hyperspectral indices such as a/b and ((a-b)/(a+b) ) sensitive to salt stress were also extracted by one-way analysis of variance (ANOVA) and Student-Newman-Keuls (S-N-K) comparison test. Our results showed that plant height, root length, leaf succulence, biomass, Chl-a, and Chl-b were sensitive to salt stress, while carotenoids (Car) and relative water content on the root were not significantly affected by salt stress. At the salt concentration of 200 mmol/L, plant height, biomass, relative water content, leaf succulence peaked. With enhanced salt stress, physiological indicators decreased. The first-order derivative spectral reflectance has the highest correlation with salt stress, compared to the control. The spectral index most sensitive to the salt stress at the canopy level is (D₉₀₃−D₈₅₁)/(D₉₀₃+D₈₅₁), for which the multiple determination coefficient (r²) is 0.9216. While the most sensitive spectral index to the salt stress is (D₄₄₂−D₆₆₇)/(D₄₄₂+D₆₆₇) at the leaf level, for which the r² is −0.898. In summary, the results indicated that there exists the quantitative relationship between the physiological indicators and spectra reflectance under salt stress and hyperspectral plant indices can effectively estimate the degree of salt stress. The inconsistency between the diagnostic hyperspectral plant indices at the canopy and leaf levels may be caused by the observation conditions, canopy structure.