This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

This paper will present the torque control design of an AFPMSM, one stator, and one rotor, using an FLC and ANFIS in-wheels fed by a three-level T-type inverter. The Surgeon ambiguous inference file of the FLC controller is built by two input vectors, the stator current error and the derivative of the stator error. These input variables include five membership functions, Negative big (NB), Negative small (NS), Equal zero (ZE), Positive small (PS), and Positive big (PB). The FLC controller is implemented with a 5x5 matrix so that the output stator voltage of the controller is required. The ANFIS controller for the neural network-based feature set and the fuzzy system. The neural network develops the dataset on the stator current error (e) and error integral (∆e). Then, the generated dataset is fed to the fuzzy logic method, and the control rules are developed. This ANFIS controller is caused by the training and testing phases. Finally, the FLC and ANFIS torque controllers are compared with the PI controller. The correctness of the proposed control structured solution is demonstrated by the simulation results of MATLAB/SIMULINK.

At present, aeroponic control is mainly regulated according to the environmental factors of aeroponics, such as the temperature, humidity, light intensity, carbon dioxide concentration, pH, and electrical conductivity (EC) of the nutrient solution. There is a lack of knowledge available in the literature for an aeroponic control system for plant growth information as the primary feedback signal. Therefore, a fuzzy logic-controlled aeroponics system was developed for the growth of lettuce as a feedback signal. After designing, the effectiveness test of system was performed with experiment having three treatments T1 (180C), T2 (220C) and without control (CK). The results show an increasing trend in shoot length, root length, and shoot area over time in all treatments. In terms of shoot area, the maximum of 345 cm² was observed in the T1 treatment, while the CK treatment had a minimum of 241.8 cm². Statistical analysis indicated that the T1 and T2 treatments were not significantly different, but both were significantly different from the CK treatment. The study demonstrates the effectiveness of the fuzzy logic control system and an 18°C nutrient solution temperature, resulting in improved lettuce growth and reduced root-to-shoot ratio. The findings suggest the potential of using fuzzy logic control in aeroponics for optimized cultivation outcomes.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

This paper is an extension to previous work that introduced successful classical-control for indoor lighting system that simultaneously control LED system and roller curtain to achieve accurate light intensity for indoor lighting applications. In this paper, Multi Input Multi Output Fuzzy Logic Controller (MIMO FLC) is proposed to replace the classical-controller. Detailed method is provided to illustrate the steps to design the required MIMO FLC that has two fuzzy input, two fuzzy output and forty-five fuzzy rules with mamdani fuzzy engine. The proposed MIMO FLC is simulated in Matlab using Simulink tools. The results are illustrated, analyzed and compared with the classical-control. The response showed very close performance to the classical-controller. The maximum average error and the maximum error with respect to “Desired Lux” inside the room is -6% and -10% respectively.

The term fuzzy refers to things that are unclear or vague. In the real world, we often encounter a situation where we cannot determine whether the state is true or false, and fuzzy logic allows for more flexible reasoning. This is a form of multivalued logic where the truth values ​​of variables can be any real number between 0 and 1, as opposed to Boolean logic where the logical values ​​can only be 0 or 1. Fuzzy logic is therefore a problem-solving technique used to evaluate all available information and thus make the best decisions. When applied to marketing, fuzzy logic allows treating customers in an individual and personalized way, instead of being fully identified within a particular market segment. Fuzzy marketing considers the degree to which a customer belongs to certain segments and subsequently allows them to be targeted with messages that engage them emotionally. To better understand the application and importance of fuzzy logic in marketing strategy, we developed a systematic review of the bibliometric literature (LRSB). It was possible to create a connection between these concepts, marketing and fuzzy logic, to increase the efforts of marketing professionals to achieve competitiveness in the unpredictable business environment.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

ABSTRACT Ethiopia is a developing country, where majority of the population lives in rural areas without access to electricity. 83% of the total population of the country use traditional biomass energy as a basic source of energy. In contrast, the country is endowed with sufficient renewable energy resources which can be used as a standalone electric energy supply system for electrifying remote areas of the country. These resources are mainly micro hydropower and wind which can be used individually or the best combination of one another. The application of hybrid renewable energy system has become an important alternative solution for rural electrification program. The Modeling and control of a hybrid PV-Wind-Hydro DG system is also addressed. Dynamic models for the major system components, namely, wind energy conversion system, PV energy conversion system, hydro, inverter, and overall fuzzy logic controller units are developed. Then, a simulation model for the proposed hybrid power system has been developed using MATLAB /Simulink environment. This is done by creating subsystem sets of the major dynamic component models and then assembling into a single aggregate model. The overall power management strategy for coordinating and/or controlling the different energy sources is also presented in the thesis work. Generally there are 800 households with total electric demand of 71.6KW.To satisfy this demand 52%, 35% and 13% is to be contributed from wind/hydro/solar respectively. To use the power economically fuzzy logic controller is used. The controller monitors the demand and the available sources and then switches to the appropriate power supply according to the written rules. Simulations have been carried out to verify the system dynamic performance using a practical load profile and weather data. The result shows that the overall power management strategy is effective and the load demand is balanced. To complete this work, a grid extension from the closest substation has been compared with hybrid system. Cost of the grid extension is estimated based on the data obtained from EEP office. This is done in order to compare the cost of the designed hybrid power system against the cost of grid extension. The result shows that breakeven grid extension distance to be 23.9km which indicates that grid extension is preferable.

Interferon-beta is one of the most widely prescribed disease-modifying therapies for multiple sclerosis patients. However, this treatment is only partially effective, and a significant proportion of patients do not respond to this drug. This paper proposes an alternative fuzzy logic system based on the opinion of a neurology expert to classify relapsing-remitting multiple sclerosis patients: high, medium, and low responder to interferon-beta. Also, a pipeline prediction model trained with biomarkers associated to interferon-beta response is proposed for predicting whether patients are potential candidates to be treated with this drug, in order to avoid ineffective therapies. The classification results shows that the fuzzy system presents a 100% efficiency compared with an unsupervised hierarchical clustering method (52%). So, the performance of the prediction model is evaluated, and a 0.8 testing accuracy is achieved. Hence, a pipeline model including data standardization, data compression, and a learning algorithm, can be a useful tool for getting reliable predictions about the response to interferon-beta.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

In March 2013, a novel avian influenza A H7N9 virus was emerged in China, which cause rapidly progressive pneumonia and with a high fatality rate. Serologic studies to evaluate neutralizing antibodies of infected patients and birds are invaluable tools for immunogenicity research of H7N9 and epidemiological investigation. Conventional neutralization assays are laborious and time-consuming which also hampered by biosafety requirement. In this study, We construct and produce pseudovirus bearing the full-length hemagglutinin (HA) of H7N9 virus in the Env-defective, luciferase-expressing HIV-1 backbone. The production of lentiviral pseudovirus was analysed by HA gene specific real-time reverse-transcription PCR, transmission electron microscopy (TEM), and Western Blot assay to prove the nucleic acid replication, the morphology of virus, and the expression of HA protein in pseudovirus. After that pseudovirus based inhibition assay was established to detect neutralizing antibodies of a panel of serum samples. Our results demonstrated that H7N9 pseudovirus which had single-cycle infection was generated. By comparing the neutralization antibody titers, pseudovirus based neutralization test could be recognized as an alternative of conventional microneutralization (MN). Hence, we conclude that it is possible to use pseudovirus inhibition assay to screen sera samples, as well as evaluate vaccine-induced neutralizing antibodies against H7N9 virus.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

The most important issue in integrated next generation wireless systems (NGWS) by fourth generation networks which consists of various wireless architectures extending from cellular networks to satellite networks is to allow everyone around the world to connect seamlessly to applications anywhere at any time through the best network. Heterogeneous networks have created many challenges such as mobility management, handoff, resource management. For always best connectivity the selection of parameters plays an important role in the decision of vertical handoff, some of parameters are depend upon MT and some are depend upon the network conditions . In this paper we designed Intelligent Vertical Handoff based on Fuzzy Logic Decision model ( IVH-FL), IVH-FL model which has five parameters for vertical handoff decision : Received Signal Strength (RSS), Available bandwidth (B), Users Preference (UP), Mobile Speed (SM) and Power Consumption (PC), with the help of Fuzzy Logic tool box and concept of fuzzy linguistic variables. The results confirmed improvement performance , and reduced the number of unnecessary handover .

The paper presents design methodology for the production process of a new product from the point of view of the assembly operations technology criterion (Design for Assembly - DFA) in the conditions of high-volume production. Mentioned are DFA methods and techniques used in the implementation of a new product. Author presents a new method to assess design for manufacturability based on fuzzy variables based on fuzzy variables. An example was given to illustrate the proposed course of action

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

This paper presents a novel real time control strategy on four-wheel independent steering system for electric vehicle with stepper motors using neural networks combined with fuzzy logic. The control of the four wheels is based on a variation of Hopfield Neural Network (VHNN) method, in which the input is the error of each steering motor and the output is processed by a hyperbolic tangent function (HTF) feeding the fuzzy logic controller (FLC), which ultimately drives the stepper motor. The whole system is made up of the four aforementioned blocks where they work in sync and inseparable from each other with the common goal of driving all the steering stepper motors at the same time. Simulation results demonstrate that the proposed control method has strong robustness and practicability under different angles and speeds.

The electricity generated from fossil fuel and nuclear energy has negative impacts on the environment and has shown a need to search for and promote the use of clean, renewable and sustainable energy resources such as wind, solar and geothermal resources. Nowadays, wind energy resource has emerged as the fastest-growing source of energy on an overall scale. However, the selection of the best location for constructing a wind farm is a vital issue that can be considered a site selection problem, which involves various conflicting factors. Therefore, it is classified as a multi-criteria decision-making (MCDM) problem. In this research, the site selection of wind power plants is conducted in Burundi country. The Fuzzy Analytic Hierarchy Process (FAHP) was used to weigh the criteria considering their relative importance. The main factors affecting optimal wind farm location considered in this study are wind speed, slope, distance from the grid network, distance to roads, and land use/land cover (LULC). Furthermore, a geographic information system (GIS) is utilized to generate the final suitability wind farm locations map. The obtained results show that 20.91% of the total study area is suitable; nevertheless, only 1.96% is highly suitable for wind farm placement. The western part of Burundi is concluded to be the most suitable area for wind farm construction and the most area is situated in Lake Tanganyika.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Meningitis is a severe disease associated with death in children under five with highest rates of infections under age of one. Vaccines for Neisseria meningitides and Haemophilus influenza are used to prevent the main causative agents of meningitis. Administration of H. influenzae type b (Hib) vaccine is recommended at 2, 4 and 6 months with a booster dose at 18 months. N. meningitidis has two commercially available vaccines, the pure polysaccharide is recommended at 24 months meanwhile the protein-conjugated vaccines at 12 months. We sought in this study to examine if coadministering the vaccines for the two main meningitis causing bacteria might be synergistic as a preliminary step towards the possibility of shuffling immunization schedule. So, we coadministered Hib vaccine with commercially available vaccines either quadrate (ACWY) polysaccharide meningococcal (Men) or conjugated meningococcal (Nim) vaccines in Balb/C mice (n = 6/group) and compared to each vaccine administered separately and controls. Thirty-five days post immunization, we measured specific antibodies titers. Hib vaccine increased Men antibody titers significantly for serotypes Y and W. When Hib vaccine was coadministrated with Nim, antibody titer for Y, W and A significantly increased. For serotype C, there was no significant difference in antibody titers among immunized groups. As for effect of meningococcal vaccines on Hib, Men significantly increased Hib antibody titers while Nim had no effect. Collectively, our data suggested that coadministration of Hib and Men or Nim vaccines was safe and had synergistic effect on immune responses elicited to both vaccines. Further studies are needed before immunization schedule modifications. Such immunization schedule recommendation should provide better protection against this life-threatening disease in young children.

Machine Learning (ML) has proved its capabilities in different scientific and industrial fields, but it needs to be further investigated in the construction industry for practical utilization. One of the use cases of ML is delegating the structural calculation process. In this study, to discuss ML’s capabilities in performing the work of a structural designer, calculations of concrete sections based on ACI (American Concrete Institute) as a case study were selected. At first, all manual design steps and standard considerations for a concrete beam section were coded parametrically in MATLAB. After comparing with structural design references to prove the accuracy of codes in calculating shear and bending capacities, the parametric results were used as initial data (Look−up table) for training the ML operators. Regarding different types of ML techniques and as a comparison between them, in the next steps, all essential codes for Fuzzy Logic (FL), Neural Network (NN) and Adaptive Neuro-Fuzzy Inference System (ANFIS) were coded in the same platform. The performance of the three coded ML operators to replace (delegate) standard calculations compared to direct calculations was individually investigated and displayed through parametric examples. After initial examples, the influences of the number of parameters and size of the Look−up table on the accuracy of each operator were discussed. The study concluded that although all three operators can delegate the standard calculation, the precision of the results differs considerably. In case of the desirable size of the Look−up table, ANFIS operators can represent the standard calculations with a different number of parameters and entirely high precision.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

The numerical implementation of the controllers allows the use of very complex algorithms with ease. However, in practice, due to its proven advantages, the PID controller (and its variants) is widely used in industrial control systems as well as in many other applications that require continuous control. Most of the methods for tuning the parameters of PID controllers are based on time-invariant linear models of the processes, which in practice can lead to poor performance of the control system. The paper presents an application of reinforcement learning algorithms in tuning of PID controllers for the control of some classes of continuous nonlinear systems. Tuning the parameters of PID controllers is done with the help of Twin Delayed Deep Deterministic Policy Gradients (TD3) algorithm which presents a series of advantages compared to other similar methods from Machine Learning dedicated to continuous state and action spaces. TD3 algorithm is an off-policy Actor-Critic based method and was used as it does not require a system model. The presented technique is applied for control of a biotechnological system which has a strongly nonlinear dynamic. The proposed tuning method is compared to the classical tuning methods of PID controllers. The performance of the tuning method based on the TD3 algorithm is demonstrated through simulation illustrating the effectiveness of the proposed methodology.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

In the dynamic landscape of the telecommunications industry, understanding and mitigating customer churn is paramount for maintaining competitive advantage and sustaining revenue streams. This comprehensive literature review delves into the intricacies of customer churn prediction, a crucial aspect in fortifying the bond between telecom businesses and their customers. The review methodically analyzes 11 articles published between 2000 and March 2024, spotlighting the strategic role of Customer Relationship Management and the prevalence of high churn rates that necessitate a shift from customer acquisition to retention strategies. Furthermore, the review navigates through the challenges inherent in churn prediction, including the complexities of managing large, imbalanced, and noisy datasets and the intricacies involved in model selection and optimization. Despite these challenges, the paper highlights the superior capability of machine learning techniques in handling complex datasets to provide accurate predictions, albeit acknowledging their practical complexities. The main aim of the study is to provide an overview, serving as a knowledge base for researchers interested in machine learning techniques within the realm of telecommunications.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

Electronic-health applications rely on large computer networks to facilitate patients' information access and to communicate various types of medical data. To examine the effectiveness of these networks, the traffic parameters need to be analysed. Due to quantity of the information carrying packets, examining each packet's transmission parameters individually is not practical, especially when a real time operation is needed. Sampling allows a subset of packets that accurately represents the original traffic to be formed. In this study an adaptive sampling method based on regression and fuzzy inference system was developed. It dynamically updates the number of packets sampled by responding to the traffic variations. Its performance was found to be superior to the conventional non-adaptive sampling methods.

Aiming at the problems of high labor intensity and high cost of manual picking, high loss rate of mechanical picking seeds, low mechanization level and difficult to guarantee the quality of picking plates in the process of picking plates of edible sunflower. Based on the principle of manual plate taking, a plate taking control system for sunflower harvesting table was designed. Through the research and analysis of the principle of taking the plate of the edible sunflower harvesting table. According to the actual operation requirements, the overall scheme of the sunflower plate control system is determined, and the control strategy of imitating artificial low loss harvesting is designed. To reduce the grain loss in the process of taking the plate and improve the control accuracy of the system on the movement speed and displacement of the key components in the process of taking the plate, a trapezoidal acceleration and deceleration control algorithm is designed as the control algorithm of taking the plate. To verify the working performance of the plate control system, with the absolute error, relative error and total loss rate of the harvest as objectives. The bench and field verification experiments were both carried out. The bench experiment showed that the speed error of the plate parts was not more than 0.028 m/s. In the bench experiments of the device, the maximum positioning error was 1.25 mm, the average relative error is only 0.94 %, and the grain loss rate was not more than 2.26 %. It result showed that the system algorithm was reliable, the positioning accuracy was high, and the taking plate operation can be completed well. The field verification experiment showed that the forward speed of the unit was in the range of 0.4~0.8 m/s, and the total loss rate of harvest was less than 5 %. When the forward speed is 0.6 m/s, the minimum harvest loss rate is 2.32 %, and which indicated the control system meets the requirements of sunflower harvesting operation.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

This study presents a vibration control using actively tunable vibration absorbers (ATVA) to suppress vibration of a thin plate. The ATVA’s is made of a sandwich hollow structure embedded with the electrorheological fluid (ERF). ERF is considered to be one of the most important smart fluids and it is suitable to be embedded in a smart structure due to its controllable viscosity property. ERF’s apparent viscosity can be controlled in response to the electric field and the change is reversible in 10 microseconds. Therefore, the physical properties of the ERF-embedded smart structure, such as the stiffness and damping coefficients, can be changed in response to the applied electric field. A mathematical model is difficult to be obtained to describe the exact characteristics of the ERF embedded ATVA because of the nonlinearity of ERF’s viscosity. Therefore, a fuzzy modeling and experimental validations of ERF-based ATVA from stationary random vibrations of thin plates are presented in this study. Because Type-2 fuzzy sets generalize Type-1 fuzzy sets so that more modelling uncertainties can be handled, a semi-active vibration controller is proposed based on Type-2 fuzzy sets. To investigate the different performances by using different types of fuzzy controllers, the experimental measurements employing type-1 fuzzy and interval type-2 fuzzy controllers are implemented by the Compact RIO embedded system. The fuzzy modeling framework and solution methods presented in this work can be used for design, performance analysis, and optimization of ATVA from stationary random vibration of thin plates.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

Metaheuristic algorithms are widely used as optimization methods, due to their global exploration and exploitation characteristics, which obtain better results than a simple heuristic. The Stochastic Fractal Search (SFS) is a novel method inspired by the process of stochastic growth in nature and the use of the fractal mathematical concept. Considering the chaotic-stochastic diffusion property, an improved Dynamic Stochastic Fractal Search (DSFS) optimization algorithm is presented. The DSFS algorithm was tested with benchmark functions, such as the multimodal, hybrid and composite functions, to evaluate the performance of the algorithm with dynamic parameter adaptation with type-1 and type-2 fuzzy inference models. The main contribution of the article is the utilization of fuzzy logic in the adaptation of the diffusion parameter in a dynamic fashion. This parameter is in charge of creating new fractal particles, and the diversity and iteration are the input information used in the fuzzy system to control the values of diffusion.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

The hybridization of machine learning methods with soft computing techniques is an essential approach to improve the performance of the prediction models. Hybrid machine learning models, particularly, have gained popularity in the advancement of the high-performance control systems. Higher accuracy and better performance for prediction models of exergy destruction and energy consumption used in the control circuit of heating, ventilation, and air conditioning (HVAC) systems can be highly economical in the industrial scale to save energy. This research proposes two hybrid models of adaptive neuro-fuzzy inference system-particle swarm optimization (ANFIS-PSO), and adaptive neuro-fuzzy inference system-genetic algorithm (ANFIS-GA) for HVAC. The results are further compared with the single ANFIS model. The ANFIS-PSO model with the RMSE of 0.0065, MAE of 0.0028, and R² equal to 0.9999, with a minimum deviation of 0.0691 (KJ/s), outperforms the ANFIS-GA and single ANFIS models.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

The proliferation of mobile and IoT devices, coupled with the advances in the wireless communication capabilities of these devices, have urged the need for novel communication paradigms for such heterogeneous hybrid networks. Researchers have proposed opportunistic routing as a means to leverage the potentials offered by such heterogeneous networks. While several proposals for multiple opportunistic routing protocols exist, only a few have explored fuzzy logic to evaluate wireless links status in the network to construct stable and faster paths towards the destinations. We propose FQ-AGO, a novel Fuzzy Logic Q-learning Based Asymmetric Link Aware and Geographic Opportunistic Routing scheme that leverages the presence of long-range transmission links to assign forwarding candidates towards a given destination. The proposed routing scheme utilizes fuzzy logic to evaluate whether a wireless link is useful or not by capturing multiple network metrics, the available bandwidth, link quality, node transmission power, and distance progress. Based on the fuzzy logic evaluation, the proposed routing scheme employs a Q-learning algorithm to select the best candidate set toward the destination. We implement FQ-AGO on the NS-3 simulator and compare the performance of the proposed routing scheme with three other relevant protocols: AODV, DSDV, and GOR. For precise analysis, we consider various network metrics to compare the performance of the routing protocols. Our simulation result validates our analysis and demonstrates remarkable performance improvements in terms of total network throughput, packet delivery ration, and end-to-end delay.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

In this paper, we employ fuzzy Sumudu transform for solving system of linear fuzzy differential equations with fuzzy constant coefficients. The system with fuzzy constant coefficients is interpreted under strongly generalized differentiability. For this purpose, new procedures for solving the system are proposed. A numerical example is carried out for solving system adapted from fuzzy radioactive decay model. Conclusion is drawn in the last section and some potential research directions are given.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Climate risk is one of the confronting factors in Indian agriculture. To overcome this distrust, a large number of sensors can be installed in the fields,The extensive IoT platform can process the data sent by these sensors.The Data stream can be processed in real-timeusing Fuzzylogic, to offer smart solution. Network coding can enhance throughput and security. Thus reducing human interaction and improve efficiency.

Climate risk is one of the confronting factors in Indian agriculture. To overcome this distrust, a large number of sensors can be installed in the fields,The extensive IoT platform can process the data sent by these sensors.The Data stream can be processed in real-timeusing Fuzzylogic, to offer smart solution. Network coding can enhance throughput and security. Thus reducing human interaction and improve efficiency.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Rapid Visual Screening (RVS) is a procedure that estimates structural scores for buildings and prioritize their retrofit and upgrade requirements. Despite the speed and simplicity of RVS, many of the collected parameters are non-commensurable and include subjectivity due to visual observations. It might cause uncertainties in the evaluation, which emphasizes the use of a fuzzy-based method. This study aims to propose a novel RVS methodology based on the interval type-2 fuzzy logic system (IT2FLS) to set the priority of vulnerable building to undergo detailed assessment while covering uncertainties and minimizing their effects during evaluation. The proposed method estimates the vulnerability of a building, in terms of Visual Damage Index, considering the number of stories, age of building, plan irregularity, vertical irregularity, building quality, and peak ground velocity, as inputs with a single output variable. Applicability of the proposed method has been investigated using a post-earthquake damage database of 28 reinforced concrete buildings from the Bingöl earthquake in Turkey.

A model of a single-server queuing-inventory system (QIS) with catastrophes and a finite waiting room for consumer customers (c-customers) has been developed. When a catastrophe occurs, all inventory in the system's warehouse is destroyed, but c-customers in the system are still waiting for restocking. In addition to c-customers, negative customers (n-customers) are also taken into account, which displaces one c-customers (if any). The policy (?, ?) is used to replenish stocks. If upon arrival of the c-customer the inventory level is zero, then according to Bernoulli’s scheme this c-customer is either lost or joining the queue. The mathematical model of the studied QIS is constructed in the form of a two-dimensional continuous-time Markov chain (2D CTMC). Exact and approximate methods for calculating the steady-state probabilities of constructed 2D CTMCs are developed and closed-form expressions are derived for calculating the performance measures. The results of numerical experiments are presented, demonstrating the high accuracy of the developed approximate formulas, as well as the behavior of performance indicators depending on the reorder point. In addition, an optimization problem is solved to obtain the optimal reorder point to minimize the expected total cost.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

Growing agricultural demands for the global population are unlocking the path to developing innovative solutions for efficient water management. Herein, an intelligent variable rate irrigation system (fuzzy-VRI) is proposed for rapid decision-making to achieve optimized irrigation in various delimited zones. The proposed system automatically creates irrigation maps for a center pivot irrigation system for a variable-rate application of water. Primary inputs are spatial imagery on remotely sensed soil moisture (SSM), soil adjusted vegetation index (SAVI), canopy temperature (CT), and nitrogen content (NI). To eliminate localized issues with soil characteristics, we used the crop nitrogen content map to provide a focused insight on issues related to water shortage. The system relates these inputs to set reference values for the rotation speed controllers and individual openings of each central pivot sprinkler valve. The results showed that the system can detect and characterize the spatial variability of the crop and further, the fuzzy logic solved the uncertainties of an irrigation system and defined a control model for high-precision irrigation. The proposed approach is validated through the comparison between the recommended irrigation and actual irrigation at two field sites, and the results showed that the developed approach gives an accurate estimation of irrigation with a reduction in the volume of irrigated water of up to 27% in some cases. Future research should implement the fuzzy-VRI real-time during field trials in order to quantify its effect on irrigation use, yield, and water use efficiency.

Digital healthcare systems play a pivotal role in providing efficient and accessible healthcare services. However, ensuring secure authentication and key agreement mechanisms is essential to protect sensitive patient data and maintain the integrity of the system. The existing methods face limitations in terms of vulnerability to cyber attacks, scalability, and resource utilization. Furthermore, the integration of blockchain technology introduces new complexities that need to be addressed. This research proposes an optimized fuzzy logic approach combined with blockchain technology to address the authentication and key agreement challenges in digital healthcare systems. The proposed solution leverages the flexibility and adaptability of fuzzy logic algorithms to handle uncertainty and imprecision in authentication decisions. By employing fuzzy logic, the system can effectively minimize false positives and false negatives, enhancing the robustness against adversarial attacks. Moreover, the integration of blockchain technology provides a decentralized and tamper-proof infrastructure for securely storing and managing authentication and key agreement data. This ensures transparency and trust in the system, mitigating the risks of unauthorized access and data manipulation. The blockchain-based architecture also enables efficient resource utilization and scalability, allowing the system to handle authentication requests in a timely manner, even in large-scale digital healthcare environments.The proposed method is evaluated by using the NIST Special Database 302 and it shows superior performance compared to existing methods, with minimum False Rejection Rate (FRR), False Acceptance Rate (FAR), and response time. Moreover, the proposed method minimizes communication overhead during the authentication process and resists different cyber attacks including a Replay attack, Man-in-the-middle attack, Denial of Service (DoS) attack, and Impersonation attack. The proposed method achieves excellent performance in terms of security, efficiency, and resistance to various cyber-attacks, making it a promising approach for secure data sharing in P2P cloud environments.

This work presents a control scheme to control the grid-connected single-phase photovoltaic (PV) system. The considered system has four 250W solar panels, a non-inverting buck-boost DC-DC converter, and DC-AC inverter with LCL filter. The control system aims to track and operate at the maximum power point (MPP) of PV panels, regulate the voltage of DC link, and supply the grid with a unity power factor. To well achieve these goals, the proposed control system consists of three parts, that are MPP tracking controller module with a fuzzy-based modified incremental conductance (INC) algorithm, a DC-link voltage regulator with a hybrid fuzzy proportional-integral (PI) controller, and a Current Controller module using the linear quadratic regulator (LQR) for grid-connected power. Based on fuzzy control and LQR, this work introduces a full control solution for grid-connected single-phase PV systems. The key novelty of this research is to analyze and prove that the newly proposed method is more successful in numerous aspects by comparing and evaluating the previous and present control methods. The designed control system settles quickly, which is critical for output stability. In addition, as compared to backstepping approach used in our past study, the LQR technique is more resistant to sudden changes and disturbances. Furthermore, backstepping method produces the larger overshoot, which has a detrimental impact on efficiency. Simulation findings under various weather conditions were compared to theoretical ones to indicate that the system can deal with variations in weather parameters.

This article presents a hybrid approach to assessing students’ foreign language proficiency in a cyber-physical educational environment. It focuses on the advantages of integrated assessment of student knowledge by considering the impact of automatic assessment, learners’ independent work, and their achievements to date. An assessment approach is described using the mathematical theory of fuzzy functions, which are employed to ensure fair evaluation of students. The largest possible number of students, whose re-evaluation of test results will not affect the overall performance of the student group, is automatically determined. The study also models the assessment process in the cyber-physical educational environment through the formal semantics of calculus of context-aware ambients (CCA).

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Permanent magnet synchronous motor (PMSM) AC servo system shows the characteristics of uncertainty, time-varying and non-linearity, which makes it difficult for traditional PID control to achieve ideal control effect. Fuzzy control has strong adaptability to the problems of parameter variation, non-linearity and model inaccuracy of the controlled object. Vector control strategy is used to study its control principle and the realization of SVPWM. Because the motor object has certain fractional order characteristics, the fuzzy parameter self-tuning PIλ control is chosen as the position regulator of servo motor. It combines the accuracy of fractional order PI control and the adaptability of fuzzy control. A simulation model of PMSM three-closed-loop system is built in MATLAB/Simulink environment. The results show that the control method is effective and can satisfy the trajectory tracking of servo control.

This article discusses a transformer-free, high-efficiency DC-DC converter besides renewable energy applications. The traditional buck-boost, classic Zeta, Sepic, and Cuk converter does have the benefits of a simple design, low cost, as well as the capacity to execute voltage step-up and step-down. Conversely, because of the detrimental consequences of the parasitic constraints of the device, the voltage conversion gain of the traditional DC-DC converter is much more restricted and the efficiency is also significantly smaller, whereas this proposed converter does have a higher voltage gain and efficiency because it is used in a single power switch, resulting in reduced switching losses and voltage stress. The said converter's design is very simple, which simplifies the operation control and reduces switching and conduction losses, leading to an efficiency of 97.4 percent. This converter seems to have the same capabilities as the Zeta converter, including continuous desired output current and desired buck-boost operation. Such an article offers the operation principle and steady evaluation, as well as a comparison with other existing high step-up configurations. The proposed converter employs a fuzzy logic controller, which improves the voltage level as well as reduces the time taken to set the voltage output of a conventional PI and ANN controller, especially in comparison to the FLC controller. For deployment, Experimental Result and MATLAB/Simulink has been used, and the modeling results indicate that the proposed controller performance has improved

This paper explores the capability of various machine learning algorithms, including Random Forests and advanced gradient boosting techniques such as XGBoost, LightGBM, and CatBoost, to predict customer churn in the telecommunications sector. For this analysis, a dataset available to the public was employed. The performance of these algorithms was assessed using recognized metrics, including Accuracy, Precision, Recall, F1-score, and the Receiver Operating Characteristic Area Under Curve (ROC AUC). These metrics were evaluated at different phases: subsequent to data preprocessing and feature selection; following the application of SMOTE and ADASYN sampling methods; and after conducting hyperparameter tuning on the data that had been adjusted by SMOTE and ADASYN. The outcomes underscore the notable efficiency of upsampling techniques such as SMOTE and ADASYN in addressing the imbalance inherent in customer churn prediction. Notably, the application of random grid search for hyperparameter optimization did not significantly alter the results, which remained comparatively unchanged. The algorithms' performance post- ADASYN application marginally surpassed that observed after SMOTE application. Remarkably, LightGBM achieved an exceptional F1-score of 89% and an ROC AUC of 95% subsequent to the ADASYN sampling technique. This underlines the effectiveness of advanced boosting algorithms and upsampling methods like SMOTE and ADASYN in navigating the complexities of imbalanced datasets and intricate feature interdependencies.

This research work deals hybrid control system based integrated Cuk converter fed brushless DC motor (BLDCM) for power factor correction. In this work, moth-flame optimization (MFO) and fuzzy logic controller (FLC) has been combined and moth –flame fuzzy logic controller (MFOFLC) has been proposed. Firstly, the BLDC motor modelling is composed with power factor correction (PFC) based integrated Cuk converter and BLDC speed is regulated using variable DC-Link inverter voltage which makes low switching operation with less switched losses. Here, with the use of switched inductor, the task and execution of proposed converter is redesigned. The DBR (diode bridge rectifier) trailed by proposed PFC based integrated Cuk converter operates in discontinuous inductor conduction mode(DICM) for achievement of better power factor.MFO is exhibited for gathering of dataset from the input voltage signal. At that point separated datasets is send to FLC to improve the updating function and minimization of torque ripple. However, our main objective is to assess adequacy of proposed method, the power factor is broke down. The execution of the proposed control methodology is executed in MATLAB/Simulink working platform and the display is assessed with the existing techniques.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Stevia Rebaudiana Bertoni Morita II, a perennial plant native to Paraguay and Brazil, is also widely cultivated in the state of Colima, Mexico, for its use as a sweetener in food and beverages. The op-timization of soil parameters is crucial for maximizing biomass production and stevioside levels in stevia crops. This research presents the development and implementation of a monitoring system to track essential soil parameters, including pH, temperature, humidity, electrical conductivity, ni-trogen, phosphorus, and potassium. The system employs a wireless sensor network to collect qua-si-real-time data, which is transmitted and stored in a web-based platform. A Mamdani-type fuzzy logic model is utilized to process the collected data and provide to farmers an integrated assessment of soil quality. By comparing the quality data output of the fuzzy logic model with a line-ar-regression model, the system demonstrated acceptable performance, with a determination coef-ficient of 0.532 for random data and 0.906 for gathered measurements. The system enables farmers to gain insights into the soil quality of their stevia crops and empowers them to take preventive and corrective actions to improve the soil quality specifically for stevia crops.

One of the most crucial elements in deeply understanding humans on a psychological level is manifested through facial expressions. The analysis of a human behavior can be informed by their facial expressions, making it essential to employ indicators such as expression (Expr), valence-arousal (VA), and action units (AU). In this paper, we introduce the method proposed in the Challenge of the 6th Workshop and Competition on Affective Behavior Analysis in-the-wild (ABAW) at CVPR 2024. Our proposed method utilizes the multi-modal Aff-wild2 dataset, which is splitted into spatial and audio modalities. For the spatial data, we extract features using a SimMiM model that was pre-trained on a diverse set of facial expression data. For the audio data, we extract features using a WAV2VEC model. To fusion the extracted spatial and audio features, we employed the cascaded cross-attention mechanism of a transformer.

In this paper it is examined how, if at all, logical laws can be normative for human reasoning, wherein the notion of normativity is analysed with respect to approaches to logic given in works of Aristotle, Descartes, Kant, Frege and Wittgenstein. During the ancient and medieval period, logic was being considered in terms of discourse and dialogical practice, but since Descartes and especially Kant it has been treated as a system of laws with which the process of individual human reasoning has been compared. Therefore, normativity can be investigated in private sphere (for thinking and reasoning) and in public sphere (for dialogic practices in a community). Wittgenstein discussed both aspects of normativity: in Tractatus, a focus is on laws of logic that are primarily normative for the state of affairs in the world, while in Philosophical Investigations an emphasis is on a social aspect of normativity (which is closer to Aristotle’s view), which is derived from adopted rules that have been applied in a certain community. Taken that way, logic is certainly normative in the public sphere, but the more difficult issue is whether logic is normative for thinking, regarding to the difference between the logical laws and those of thought.

Abstract: This study investigates the transition to sustainable shipping industry within the framework of the IMO's 2050 carbon neutrality objective, focusing on socio-technical systems analysis. The research delves into the sustainable paradigm shift towards alternative marine fuels such as LNG, methanol, ammonia, and hydrogen from a socio-technical transition perspective, analyzing the multi-level per-spective challenges and opportunities. Specifically, it scrutinizes the implications of adopting these al-ternative fuels for global shipping, identifying technical uncertainties, financial constraints, and infra-structure needs. Through a comprehensive review of existing literature on ship emissions and alterna-tive fuels, coupled with socio-technical transition theory, the study addresses the multifaceted chal-lenges and opportunities in meeting the IMO's environmental objectives. It emphasizes the necessity of collaborative governance, innovative niche strategies, and a holistic approach to leverage the current window of opportunity in facilitating the maritime industry's transition to sustainable fuel options. Fi-nally, this research enhances our understanding of the intricate interplay between technological, social, industrial, and cultural dynamics in the greening of shipping and offers insights into the strategic adop-tion of environmentally friendly marine fuels for a sustainable future.

The bridge crane is often used in a complex environment, often subject to interference of all loads. Some uncertainties factors often have an inevitable impact on its swing. So the force situation of the bridge crane during a working cycle is analyzed, and a three-dimensional dynamic mathematical model of the bridge crane is built. Through the simulation analysis of the model under the action of driving force and wind load, the change law of the swing angle of the bridge crane is studied. Then, the fuzzy control theory is used to determine the control parameter in the anti sway control process. The position, swing angle deviation and deviation rate of the bridge crane are taken as the input, and the parameter correction is obtained after the fuzzification by using the center of gravity method, the anti sway fuzzy control system of the bridge crane is designed and simulated. The research results show that the fuzzy PID anti sway controller can not only improve the adaptability of the control system, but also overcome the large overshoot, quickly restrain the swing, and effectively realize the anti sway function of the bridge crane.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

Oedaleus decorus asiaticus, Calliptamus abbreviatus, Angaracris rhodopa, and Myrmeleotettix palpalis are the main grasshoppers that harm the natural grassland in the Hexi Corridor. In this study, the MaxEnt model was employed to identify the key environmental factors affecting the distribution of the four grasshoppers habitats and to assess their distribution under current and future climate change conditions. The aim was to provide a basis for grasshopper monitoring, prediction, and precise control. In this study, 61 occurrences of O. decorus asiaticus, 68 occurrences of A. rhodopa, 58 occurrences of C. abbreviatus, and 92 occurrences of M. palpalis were recorded by GPS, and the distribution of suitable habitats for O. decorus asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis were predicted under current and future climatic scenarios using a MaxEnt model. The average AUC and TSS values of the four grasshoppers were greater than 0.9, and the simulation results were excellent and highly reliable. The mean annual precipitation was the main factor limiting the current range of suitable areas for these four species. Under the current climate, O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the central and eastern parts of the Hexi Corridor, and M. palpalis was distributed throughout the Hexi Corridor, with a potential distribution area of 1.44×104, 1.43×104, 1.29×104, and 2.12×104 km2, accounting for 15.3, 15.2, 13.7, and 22.5% of the total area of the grasslands in the Hexi Corridor, respectively. The highly suitable areas of O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the east-central part of Zhangye City, the western part of Wuwei City, and the western and southern part of Jinchang City, with areas of 0.35×104, 0.29×104, and 0.20×104 km2, accounting for 3.7, 3, and 2.2% of the grassland area, respectively. The high habitat of M. palpalis was mainly distributed in the southeast of Jiuquan City, the west, middle, and east of Zhangye City, the west of Wuwei City, and the west and south of Jinchang City, with an area of 0.32×104 km2, accounting for 3.4% of the grassland area. In the 2030s, the range of O. asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis was predicted to decrease.

The feedback collection and analysis has remained an important subject matter since long. The traditional techniques for student feedback analysis are based on questionnaire-based data collection and analysis. However, the student expresses their feedback opinions on online social media sites, which need to be analyzed. This study aims at the development of fuzzy-based sentiment analysis system for analyzing student feedback and satisfaction by assigning proper sentiment score to opinion words and polarity shifters present in the input reviews. Our technique computes the sentiment score of student feedback reviews and then applies fuzzy-logic module to analyze and quantify student’s satisfaction at the fine-grained level. The experimental results reveal that the proposed work has outperformed the baseline studies as well as state-of-the-art machine learning classifiers.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

The informational synthesis of neural structures, processes, parameters and characteristics that allow a unified description and modeling as neural machines of natural and artificial neural systems is presented. The general informational parameters as the global quantitative measure of the neural systems computing potential as absolute and relative neural power were proposed. Neural information organizing and processing follows the way in which nature manages neural information by developing functions, functionalities and circuits related to different internal or peripheral components and also to the whole system through a non-deterministic memorization, fragmentation and aggregation of afferent and efferent information, deep neural information processing representing multiple alternations of fragmentation and aggregation stages. The relevant neural characteristics were integrated into a neural machine type model that incorporates unitary also peripheral or interface components as the central ones. The proposed approach allows overcoming the technical constraints in artificial computational implementations of neural information processes and also provides a more relevant description of natural ones.

Prostate cancer is the second leading cause of death in males in America, with advanced prostate cancers exhibiting a 5-year survival rate of only 32%. Castration-resistance is often developed during the course of treatment, though its influences require further understanding. This study explores the human microbiome for its implications in castration-resistance and metastasis in prostate cancer. RNA sequencing data was downloaded for bone and soft tissue biopsies of patients with metastatic castration-resistant prostate cancer. These sequences were mapped to bacterial sequences to yield species-level abundance approximations. Numerous species were found to correlate to the expression of known markers of castration-resistance, including AR, PI3K, and AKT. Castration-resistance-associated signaling pathways were also enriched with these species, including PI3K-AKT signaling and endocrine resistance. For their implications in cancer aggression and metastasis, cancer stem cell markers were further explored for relation to these species. EGFR and SLC3A2 were widely downregulated with greater abundance of most species. Our results suggest that the microbiome is heavily associated with castration-resistance and stemness in prostate cancer. By considering the microbiome’s importance in these factors, we may better understand the highly aggressive and highly invasive nature of prostate cancer, allowing for needed improvement in the treatment of this disease.

The effectiveness of Fuzzy Inference Systems (FISs) in manipulating uncertainty and nonlinearity makes them a subject of significant interest for decision-making in embedded systems. Accordingly, optimizing FIS hardware improves its performance, efficiency, and capabilities, leading to a better user experience, increased productivity, and cost savings. To be compatible with the limited power budget in most embedded systems, this paper presents a framework to realize ultra-low power FIS hardware. It supports optimizations for both conventional arithmetic as well as MSDF-computing to be highly consistent with MSDF-based sensors. In MSDF-computing FIS all the processes of fuzzification, inference, and defuzzification are done on serially coming data bits. To demonstrate the efficiency of the proposed framework, we utilized Matlab, Chisel3, and Vivado to implement it from high-level descriptions of FIS to hardware synthesis. We also developed a Scala library in Chisel3 to establish a connection between these tools, bridging the gap, and facilitating design space exploration at the arithmetic level. Furthermore, we realized an FIS for the navigation of autonomous mobile robots in unknown environments. Synthesis results show the superiority of the output of our suggested design framework in terms of resource usage as well as power and energy consumption compared to the Matlab HDL code generator output.

Safety is very important in aviation since a loss of safety frequently results in both fatalities and financially damaging situations that are typically unrecoverable. Thus, achieving safety as much as possible is the primary goal of practically all aviation technology work. In this study, an Adaptive Neuro-Fuzzy Inference System (ANFIS)-based classifier is created to estimate the fault risk factor of airplanes. Five categories of real fleet data belonging to structure, electrical, avionic, motor systems, and incident statistics of the planes have been used for classifier development. A risk factor determination for each plane is the output of the developed intelligent classifier, and it can be used to identify general overhaul candidate planes and stop defects and crashes before they happen. The obtained results show that using ANFIS provides a great capability in processing many inputs and outputs depending on different types and classes in the aviation industry and thus predicting the failure risk of the airplane efficiently.

Resource conflicts represent a significant global challenge in regions abundant with natural re-sources. Modelling the myriad factors driving natural resource-based conflicts (NRBCs), spanning environmental, health, socio-economic, and political dimensions, is a complex endeavor exacer-bated by data scarcity. Furthermore, existing quantitative studies often focus solely on large-scale conflicts. This article introduces a novel algorithm, the Spatially Explicit Fuzzy Logic-Adapted Model for Conflict Management (SEFLAME-CM), which integrates the local knowledge of stakeholders into spatial decision-making technologies to support sustainable peace efforts. The results are validated with spatial multi-criteria evaluation (SMCE) using spatial statistics. The Moran’s I scatter plots for the overall conflicts reveal significant values of 0.99 and 0.98 for both the SEFLAME-CM and SMCE, respectively, with significant spatial autocorrelation. While there re-mains room for improvement in enhancing the model's quality, SEFLAME-CM demonstrates its capacity to transparently model complex real-world problems. The findings underscore the im-perative for a holistic approach to addressing environmental degradation, socio-economic, and political drivers of resource conflicts at the community level. Our paper demonstrates the signif-icance of spatial information technologies and knowledge exchange between experts and local stakeholders in effectively managing resource conflicts. These insights should inform national policies and international interventions, ensuring that the complex underlying issues are ad-dressed while prioritizing the knowledge and needs of affected communities.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

Iterated games, in which the same economic interaction is repeatedly played between the same agents, are an important framework for understanding the effectiveness of strategic choices over time. To date very little work has applied information theory to the information sets used by agents in order to decide what action to take next in such strategic situations. This article looks at the mutual information between previous game states and an agent's next action by introducing two new classes of games: ’invertible games’ and ‘cyclical games'. By explicitly expanding out the mutual information between past states and the next action we show under what circumstances these expressions can be simplified. These information measures are then applied to the Traveler's Dilemma game and the Prisoner's Dilemma game, the Prisoner's Dilemma being invertible, to illustrate their use. In the Prisoner's Dilemma a novel connection is made between the computational principles of logic gates and both the structure of games and the agents' decision strategies. This approach is applied to the cyclical game Matching Pennies to analyse the foundations of a behavioural ambiguity between two well studied strategies: ‘Tit-for-Tat' and ’Win-Stay, Lose-Switch'.

Background and Objectives: In this current state, Type 2 Diabetes Mellitus (T2DM) is more prevalent in the population, and metformin is used as a first-line medication for treating it. There was up surge in the utilization of alternative therapies in the management of diabetes. Especially in diabetes, Herbal medicines are considered safe and reliable by majority of the population. Aim: The purpose of this research is aimed to estimate the safety and efficacy of Polyherbal Metabolite Compounds (PHMC) capsules in adults with T2DM. Materials and Methods: In this study, 60 T2DM patients aged 18-60 years were randomly assigned to Groups A (30) receiving Metformin 500 mg twice a day after food and Group B (30) receiving PHMC capsule 500 mg twice a day after food in a prospective, randomized and open-label clinical study. The in-silico simulation study was performed to selected plants major compounds on target protein Insulin-like Growth Factor-1 (1K3A). Result: The PHMC is found to be safe and effective in the management of T2DM. The FBS, PPBS and HbA1c were significantly lowered (p

This paper introduces a fuzzy logic-based autonomous ship-deck landing system for fixed-wing Unmanned Aerial Vehicles (UAVs). The ship is assumed to maintain a constant course and speed. The aim of this fuzzy logic landing model is to simplify the task of landing UAVs on moving ships in challenging maritime conditions, relieving operators from this demanding task. The designed UAV ship-deck landing model is based on a fuzzy system comprised of three interconnected subsystems. Each subsystem consists of three inputs and one output incorporating various fuzzy rules to account for external factors during ship-deck landings. Specifically, the Fuzzy Logic System (FLS) takes inputs such as the airspeed, the relative wind direction and speed, the range from the deck and the UAV's flight altitude. The FLS outputs provide data on the Speed of the UAV relative to the ship’s velocity, the Bank Angle, and the Angle of Descent of the UAV. The performance of the designed intelligent ship-deck landing system is evaluated using the standard configuration of MATLAB Fuzzy Toolbox.

Computer systems are involved in many critical human applications today, so that a small error can lead to serious and dangerous problems. These errors can be from an error in the incorrect design of the user interface to an error in the program code. The success of a software product depends on several factors. Given that different organizations and institutions use software products, the need to have a quality and desirable Software according to the goals and needs of the organization makes measuring the quality of software products. an important issue for most organizations and institutions, To be sure of having the right software. It is necessary to use a standard quality model to examine the features and sub-features for a detailed and principled study in the quality discussion. In this study, the quality of Word software was measured by Adaptive Neural Fuzzy Inference System. In recent years, powerful systems called fuzzy inference systems on The basis of adaptive neural network (ANFIS) has been used in various sciences. Using the power of neural network training and the linguistic advantage of fuzzy systems, these types of systems have been able to realize the advantages of the two in terms of analyzing very powerful complex processes. Considering the importance of software quality and to have a good and usable software in terms of quality and measuring the quality of software during the study. It was applied at different levels to make the result of measuring the quality of Word software more accurate and closer to reality. In this research, the quality of the software product is measured based on the adaptive neural-fuzzy inference system in ISO standard. According to the results obtained in this study, it is understood that quality is a continuous and hierarchical concept and the quality of each part of the software at any stage of production can lead to high quality products.

The purpose of the study is to control the ratio of programs of different genres when forming the broadcast grid in order to increase and maintain the rating of the channel. In the multichannel environment, television rating control consists of selecting such content, ratings of which are completely restored after advertising. A hybrid approach combining the benefits of semantic training and fuzzy relational equations in simplification of the expert recommendation systems construction is proposed. The problem of retaining the television rating can be attributed to the problems of fuzzy resources control. The increase or decrease trends of the demand and supply are described by primary fuzzy relations. The rule-based solutions of fuzzy relational equations connect significance measures of the primary fuzzy terms. Rules refinement by solving fuzzy relational equations allows avoiding labor-intensive procedures for the generation and selection of expert rules. The solution set generation corresponds to the granulation of the television time, where each solution represents the time slot and the granulated rating of the content. In automated media planning, generation of the weekly TV program in the form of the granular solutions provides the decrease of the time needed for the programming of the channel broadcast grid.

An orthogonal pore ('orthopore') is conceptually based on an electrolytic cell with a standard pore (the main or 'longitudinal' pore) between cis and trans compartments filled with electrolyte and augmented by a secondary or 'transverse' pore in the form of a channel that is perpendicular to and intersects the main pore. Orthopores can be designed at different scales: macro through micro to nano. With nano-sized pores an analyte (polymer) can be threaded through the main pore and exposed at the junction to electrolyte flow through the secondary pore. Polymer translocation speeds are then independent of the current measured, which can be of an arbitrary magnitude even with the polymer stationary. Orthopores have a wide range of potential applications, including polymer (DNA and protein) sequencing, DNA unzipping, logic circuitry, and protein identification. The present report shows how orthopores can be used to implement boolean logic.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Food systems will need to undergo considerable transformation. To be better prepared for and resilient to uncertainty and disturbances in the future, resource users and managers need to further develop knowledge about the food and farming system, with its dominating feedback structures and complexities, and to test robust and integrated system-based solutions. This paper investigates how participatory system dynamics modeling can be adapted to groups at the community level with low or no formal educational background. The paper also analyzes the refinement of workshop participants’ mental models as a consequence of a participatory system dynamics intervention. For this purpose, we ran two workshops with small-scale farmers in Zambia. Analysis of workshop data and post-workshop interviews shows that participatory system dynamics is well adaptable to support an audience-specific learning-by-doing approach. The use of pictures, objects and water glasses in combination with the basic aspects of causal loop diagramming makes for a well-balanced toolbox. Participants acquire understanding that is also relevant beyond systems thinking in that is offers a range of practical insights such as a critical evaluation of common food security strategies.

Anthropogenic development can strongly influence natural river processes, leading to environmental changes that negatively affect important habitats and biodiversity, and consequently reduce economically important natural resources. This study investigated the effects of salinity intrusion on the habitat of the clam Corbicula japonica in the Seomjin River estuarine zone. We employed the Environmental Fluid Dynamics Code (EFDC) model, which incorporates topographic data and hydrological changes, to simulate salinity concentrations. Two salinity measurement facilities were installed in Seomjin River estuarine and operated to optimize the EFDC model. The results show that reduced flow rates due to intake have a negligible impact on the increased salinity. Maintaining optimal salinity (15–20 psu) during neap tides at the Seomjin River Bridge requires constant high flow rates, which poses significant challenges. Saltwater stratification is identified as the primary cause of pronounced salinity stratification, particularly during neap tides. Addressing this issue through river discharge and intake facility operation is challenging. Structural measures, including riverbed restoration and underwater barriers, are recommended to improve resistance to seawater intrusion. Future research should aim to develop scenarios to reduce salinity concentrations, quantify the reduction efficiency, and propose region-specific measures.

The estimation of the efficiency of road transport vehicles remains a significant problem for contemporary transport companies, as the technological process is influenced by numerous stochastic impacts, such as demand stochasticity, road conditions uncertainty, transport market fluctuations, etc. To consider the uncertainty related to the estimation of the vehicles’ fleet efficiency, we propose a fuzzy-logic approach, where the efficiency of a given vehicle is described by a membership function. The efficiency of the whole fleet and its rational structure in that case can be evaluated as a fuzzy set. To demonstrate the developed approach, we depict a case study of using cargo vehicles for deliveries of agricultural products in the Republic of Kazakhstan. The numeric results are presented for the selected models of vehicles that a transport company uses to service a set of clients located in Northern Kazakhstan.

Only a handful of microbial mosquito larval pathogens have been described to date. Sampling of several natural enzootic infections of mosquito larvae in southwestern Florida indicated the presence of microbial pathogens capable of extensive larval mortality. Microscopic analysis of one sample site revealed extensive apparent growth of a Pythium-like microbe on mosquito lar-vae, with highest infection observed on the siphon and head regions. Structures consistent with sporangia were seen on infected insects after lactophenol blue staining, and higher resolution scanning electron micrographs (SEM) showed sporangia and encysted zoospores targeting the head and siphon regions. The isolate was single colony purified and molecular identification targeting the ITS and COX1 loci coupled to phylogenetic reconstruction indicated that the isolate belonged to the Pythium genus, but was distinct from its closest characterized species, P. angusta-tum. Morphological features were characterized, with the isolate showing rapid growth on all mycological media tested and relatively high thermotolerance, capable of robust growth at 37oC, and hence was designated, P. thermoculicivorax. Sampling from a second series of natural infec-tions of mosquito larvae resulted in the molecular identification of three Trichoderma isolates, one with high similarity to T. strigosum, and the other two clustering with, but distinct from, T. asperellum. These data highlight the occurrence of natural enzootic infections of mosquito larvae, potentially as a resource for the identification of new mosquito pathogens.