A high-gain broadband circularly polarized crossed dipole antenna is designed. This antenna utilizes two pairs of cross dipoles and a pair of phase delay lines to form circularly polarized radiation. Open-circuit stubs are loaded on the four arms of these two pairs of cross dipoles to introduce new circularly polarized resonating frequency. A rectangular ring patch is introduced directly below the cross dipoles to form the third circularly polarized resonating frequency, thereby broadening the axial ratio bandwidth of the antenna. In addition, metal posts are loaded at the four right angles of the rectangular ring patch to increase the antenna gain. Measurement results show that the antenna achieves a 3dB axial ratio bandwidth of 29.2% (1.9 GHz-2.55 GHz) and maintains a gain of 7.5 dB within the passband, exhibiting good circularly polarized radiation performance.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

In recent years, the AHRS has become an important research area. In order to improve the orientation measurement accuracy of AHRS, this paper first expounds the algorithm principle of the AHRS. Then, aiming at the problem of poor stability of the traditional gradient descent method under high dynamics or large magnetic field interference, a gain-scheduled anti-interference AHRS orientation algorithm is designed. By using the switching architecture designed with this algorithm for gain scheduling, it can ensure stable performance while being subjected to apparent acceleration and ferromagnetic interference. Finally, experimental verification is conducted, and the experimental results show that: in the presence of interference, the roll angle error is 0.0350°, the pitch angle error is 0.0277°, and the yaw angle error is 0.9611°, thereby verifying the strong anti-interference performance of the gain-scheduled AHRS orientation algorithm proposed in this paper.

The relationship of Amyotrophic Lateral Sclerosis, Parkinson Disease and other age-related neurodegenerative diseases associated with mitochondrial dysfunction has led to study of the mitochondrial fission gene Drp1 in Drosophila. Drp1 can interact with mitochondrial proteins including parkin and the Drosophila Bcl-2 proteins. Mutations in Drp1 can lead to mitochondrial dysfunction and neuronal loss. Ddc-Gal4 was exploited to direct the expression of Drp1 and the inhibition of Drp1 in neurons. Here, the inhibition of Drp1 seems to compromise locomotor function throughout life but does not alter longevity. The consequences of Drp1 overexpression can be suppressed through overexpression of pro-survival Bcl-2 gene Buffy or by inhibition of the pro-cell death Bcl-2 homologue Debcl. The expression of Buffy suppresses the poor climbing induced by loss of Drp1 function. Interestingly, the loss of parkin function is rescued by the directed inhibition of Drp1. Alteration of the expression of Drp1 acts to phenocopy neurodegenerative disease phenotypes in Drosophila, while overexpression of Buffy can counteract these phenotypes to improve overall health. The pro-survival effect of Buffy can rescue the phenotypic effect due to the Drp1-induced apoptosis. The diminished health due to either overexpression or inhibition of Drp1 has produced a novel model to investigate mechanisms underlying neurodegenerative disease.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from <5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Iron is an essential nutrient for humans and microbes, such as bacteria. Iron deficiency occurs commonly in critically ill patients, but iron replacement therapy is not considered during the acute phase of critical illness, since it increases iron availability for invading microbes and oxidative stress. However, persistent iron deficiency in the recovery phase is harmful with potential adverse outcomes such as cognitive dysfunction, fatigue and cardiopulmonary dysfunction. Therefore, it is important to treat iron deficiency timely and efficiently. This article reviews current knowledge about iron-related biomarkers in critically ill patients and provides possible criteria to guide decision-making for iron supplementation in the recovery phase of critical illness.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

A Berry geometrical phase is identified in a strongly metastable system containing dynamically responsive clathrate hydrate structures within a crystal-fluid material. High energy degeneracy in the associated chemistry produces local stability and false vacuum conditions that lead to non-extensive and non-additive contributions in the fundamental thermodynamic relation. Application of Ginzburg-Landau theory and the scaling laws reveals a coherence length and a penetration depth for a macro-scale dual superconductor. The coherence length determines non-extensive volume changes whilst its inverse gives the Higgs mass. The penetration depth determines the extent of QCD vacuum suppression whilst its inverse gives the vector boson mass together with indirect manifestation as non-additive hyperbolic curvature. Simultaneous emergence of the Ginzburg-Landau superconducting phase transition is consistent with gauge-invariant coupling of the scalar field to the Yang-Mills action in QCD. The discovery of an energy gap in the gradient energy term of the system Lagrangian is associated with a critical correlation length revealed in the transition from a gapped to a gapless superconducting state. Together with the emergence and absorption of the Higgs-like scalar field, a mechanism for describing a renormalized QCD mass gap arises.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

This study presents a novel predictive model to address the churn problem in the motor insurance sector using a dual-phase framework. The first phase employs a cave-degree perturbation technique for effective feature selection, while the second phase applies the Magnetic Force Perturbation Technique (MFPT) to optimize the search process and avoid local optima traps. Two metaheuristics are proposed: the Adaptive Random Forest-Assisted Large Neighborhood Feature Optimizer (ARALFO) and the Adaptive Random Forest Particle Swarm Optimizer (ARFPSO) to enhance churn prediction accuracy. The model was evaluated on two real-world motor insurance datasets, achieving a 95% accuracy rate and outperforming state-of-the-art algorithms. An ablation study confirmed the significant impact of the cave-degree and MFPT techniques in boosting predictive performance.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

Background/Aim: microRNAs (miRNAs) are key regulators of both physiological and pathophysiological mechanisms in diabetes and gastrointestinal (GI) dysmotility. Our previous studies have demonstrated the therapeutic potential of miR-10a-5p mimic and miR-10b-5p mimic (miR-10a/b mimics) in rescuing diabetes and GI dysmotility in murine models of diabetes. In this study, we elucidated the safety profile of a long-term treatment with miR-10a/b mimics in diabetic mice. Methods: Male C57BL6 mice were fed a high-fat, high-sucrose diet (HFHSD) to induce diabetes and treated by five subcutaneous injections of miR-10a/b mimics for a 5-month period. We examined the long-term effect of the miRNA mimics on diabetes and GI dysmotility, including an assessment of cancer risk as well as liver and colon inflammation using cancer and inflammatory biomarkers. Results: HFHSD-induced diabetic mice subcutaneously injected with miR-10a/b mimics monthly for 5 months exhibited a marked reduction in fasting blood glucose levels with restoration of insulin and significant weight loss, improved glucose and insulin intolerance, and restored GI transit time. In addition, the miR-10a/b mimic treated diabetic mice showed no indication of risk for cancer development and inflammation induction in the liver, colon, and blood for the 5 months post injections. Conclusion: This longitudinal study demonstrates that miR-10a/b mimics, when subcutaneously administered in diabetic mice, effectively alleviate diabetes and GI dysmotility for 5 months with no discernible risk for cancer or inflammation in the liver and colon. The sustained efficacy and favorable safety profiles position miR-10a/b mimics as promising candidates in miRNA-based therapeutics for diabetes and GI dysmotility.

Information theoretic quantities such as entropy, entropy rate, information gain, and relative entropy are often used to understand the performance of intelligent agents in learning applications. Mean squared error has not played a role in these analyses, primarily because it is not felt to be a viable performance indicator in these scenarios. We build on a new quantity, the log ratio of entropy powers, to establish that minimum mean squared error (MMSE) estimation, prediction, and smoothing are directly connected to Mutual Information Gain or Loss in an agent learning system modeled by a Markov chain for many probability distributions of interest. Expressions for mutual information gain or loss are developed for MMSE estimation, prediction, and smoothing and an example for fixed lag smoothing is presented.

. Protein cysteine S-glycosylation is a relatively rare and less well characterized post-translational modification (PTM). Creating reliable model proteins that carry this modification is challenging. The lack of available model or natural S-glycosylated proteins significantly hampers the development of MS-based methodologies for detecting protein cysteine S-glycosylation in real-world proteomic studies. There is also limited MS-sequencing data describing easier to create synthetic S-glycopeptides. Here, we present the results of an in-depth manual analysis of automatically annotated CID/HCD spectra for model S-glucopeptides. The CID spectra show a long series of y/b-fragment ions with retained S-glucosylation, regardless of the dominant m/z signals corresponding to neutral loss of 1,2-anhydroglucose from the precursor ions. In addition, the spectra show signals manifesting glucosyl transfer from the cysteine position onto Lys, Arg side chains, and a peptide N-terminus. Other spectral evidence indicates that the N-glucosylated initial products of transfer are converted into N-furanosylated (i.e., glycated) structures due to Amadori rearrangement. We discuss the peculiar transfer of the glucose oxocarbenium ion (Glc+) to positively charged guanidinium residue (ArgH+) and propose a mechanism for the gas-phase Amadori rearrangement involving a hydride ion shift.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

The DEAD-box RNA helicase DDX3X is a multifunctional protein involved in RNA metabolism and stress responses. In this study, we investigated the role of RG/RGG motifs in the dynamic process of liquid-liquid phase separation (LLPS) of DDX3X using cell-free assays and explored their potential link to cancer development through bioinformatic analysis. Our results demonstrate that the number, location, and composition of RG/RGG motifs significantly influence the ability of DDX3X to undergo phase separation and form self-aggregates. Mutational analysis revealed that the spacing between RG/RGG motifs and the number of glycine residues within each motif are critical factors in determining the extent of phase separation. Bioinformatic analysis of cancer genomic datasets uncovered a significant enrichment of DDX3X mutations in RG/RGG motifs across multiple cancer types, particularly in the N-terminal region of the protein. Furthermore, we found that DDX3X is co-expressed with the stress granule protein G3BP1 in several cancer types and can undergo co-phase separation with G3BP1 in a cell-free system, suggesting a potential functional interaction between these proteins in phase-separated structures. DDX3X and G3BP1 may interact through their RG/RGG domains and subsequently exert important cellular functions under stress situation. Collectively, our findings provide novel insights into the role of RG/RGG motifs in modulating DDX3X phase separation and their potential contribution to cancer pathogenesis.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

Background: Despite advances in the treatment of hepatocellular carcinoma (HCC) over the last few decades, treatment opportunities for patients with HCC remain limited. HCC is the most common form of liver cancer, accounting for approximately 90% of all cases worldwide. Moreover, apart from the current pharmacological interventions, hepatic resection and liver transplantation are the mainstay curative approaches for patients with HCC. Methods: This systematic review included phase I, II, III, and IV clinical trials (CTs) and randomized controlled trials (RCTs) on current treatments for patients with HCC in an Asian population (2013–2023). A total of 427 articles were screened, and 184 non-duplicate publications were identified. After screening titles and abstracts, 96 publications were excluded, and another 28 were excluded after full-text screening. The remaining 60 eligible RCTs/CTs were finally included. Results: Sixty clinical trials fulfilled our inclusion criteria and screened 36 drugs as monotherapy or combination therapy for HCC. Most studies used sorafenib alone or in combination with any of the treatment regimens. Lenvatinib or atezolizumab with bevacizumab was used for HCC after initial sorafenib treatment. Eighteen studies compared the efficacy of sorafenib with that of other drugs, including lenvatinib, cabozantinib, tepotinib, tigatuzumab, linifanib, erlotinib, resminostat, brivanib, tislelizumab, selumetinib, and refametinib. Conclusion: This study provides comprehensive insights into effective treatment interventions for HCC in Asian populations. The overall assessment indicated that sorafenib alone or in combination with atezolizumab and bevacizumab has been the first treatment choice in the past decade to achieve better outcomes in patients with HCC in an Asian population

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Epilepsy is known to cause alterations in neural networks. However, many details of these changes remain poorly understood. The objective of this study was to investigate changes in the properties of hippocampal CA1 pyramidal neurons and their synaptic inputs in a rat lithium-pilocarpine model of epilepsy. In the chronic phase of the model, we found a marked loss of pyramidal neurons in the CA1 area. However, the membrane properties of the neurons remained essentially unal-tered. The results of the electrophysiological and morphological studies indicate that the direct pathway from the entorhinal cortex to CA1 neurons is reinforced in epileptic animals, whereas the inputs to them from CA3 are either unaltered or even diminished. In particular, the dendritic spine density in the str. lacunosum moleculare, where the direct pathway from the entorhinal cortex ter-minates, was found to be 2.5 times higher in epileptic rats than in control rats. Furthermore, the summation of responses upon stimulation of the temporoammonic pathway was enhanced by approximately twofold in epileptic rats. This enhancement is believed to be a significant con-tributing factor to the heightened epileptic activity observed in the entorhinal cortex of epileptic rats using an ex vivo 4-aminopyridine model.

Abstract: — management of the Continuous Stirred Tank Reactor (CSTR) operation has proven to be a difficult undertaking due to the complex and ever-changing nature of its behavior, which is both nonlinear and dynamic, which is further compounded by its instability. Attempts have been made to use Proportional-Integral-Derivative (PID) controllers for such processes, but the performance is often poor due to the inherent limitations of the controllers. In contrast, heuristic algorithms have been employed to tune the controllers, but these methods can only provide optimal performance for a restricted range of parameter variations. This paper presents a novel approach that involves using a conventional gain scheduling PID controller in combination with a fuzzy gain scheduling (FGS) controller method to calibrate set-point weighted PID controllers for the CSTR process. The paper outlines the design of the controllers and evaluates their performance by subjecting them to varying input signals within the given bandwidth.

In areas with a deep floor plan, the distribution of natural light is not uniform. Consequently, relying solely on daylight may not suffice to meet the space's lighting requirements, necessitating the use of artificial lighting in darker areas. Therefore, a lighting system is needed that not only controls the glare near the windows but also increases the light at the end of the room and provides uniform daylight. One of the widely used systems is the “light shelf“which has three main functions: shading, increasing the depth of light penetration and reducing glare. Review articles about light shelves have been done in 2015 and 2017, while more than 80% of the studies have been carried out since 2016 and light shelves with more diverse forms and dynamic elements and many consolidations were proposed. Therefore, there is a need for a more comprehensive review. The main question of this research is how different parameters (including climate, material, ceiling and integrated systems) can help to increase the efficiency of light shelves. By using a systematic review, studies in the past three decades were classified in order to determine the effect of these parameters on improving lighting performance and controlling solar heat gain.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

A convenient and efficient strategy for the preparation of 2-sulfonylindoles has been achieved through iodophor/H2O2-mediated 2-sulfonylation of indoles with readily available sulfonyl hydrazides in aqueous phase. Iodophor is commercially available and serves as the green catalyst and aqueous phase. A series of 2-sulfonylated products from indoles and N-methylpyrrole were synthesized in moderate yields in only 10 min. Control experiments were also conducted to reveal the mechanism. This method is environment friendly, easy to operate and suitable for a wide range of substrates.

The author previously investigated the thermodynamic properties of the one-dimensional Potts-SOS model on the lattice of positive natural numbers N in [Akin H, Phys. Scr. 99 (2024), 055231]. In this present paper, we extend that research by determining the Gibbs measures for the same mixed-type model using partition functions constructed on a second-order semi-infinite Cayley tree. By leveraging the self-similarity of the Cayley tree, we analyze the behavior of these partition functions and identify the regions where phase transitions occur. We pinpoint these phase transition regions through a stability analysis of the dynamical system associated with the model at specific fixed points.

We evaluated the immunogenicity persistence of different immunization regimens of freeze-dried human rabies vaccine (Vero cells) in the 10–60 years age group of the Chinese population. Based on phase III clinical trials of Vero cells, participants who completed the full course of immunization were continuously enrolled in four-dose trial, five-dose, and five-dose control groups. Venous blood samples were collected 12 months after completion of the full immunization for rabies virus-neutralizing antibody (RVNA) testing, and the antibody-positive rate and geometric mean concentration (GMC) were calculated. Analysis of variance was used to compare three groups. The four-dose trial, five-dose trial, and five-dose control groups included 200, 186, and 214 participants, respectively. Twelve months after full immunization, the overall RVNA-positive rates were 97.00%, 93.55%, and 94.86% in the four-dose trial, five-dose control, and five-dose trial groups, respectively. The post-immunization RVNA GMCs values were 2.50, 2.05, and 2.04 IU/mL, respectively, with no statistically significant differences between them. Twelve months after full immunization, the overall RVNA-positive rate remained high, demonstrating satisfactory immunogenicity persistence for both immunization regimens.

Background and Objectives To compare navigator-gated three-dimensional T1-weighted gradient-echo sequences (NG-3D T1W-GRE) with standard breath-hold T1W-GRE (BH T1W-GRE) for the detection of HCC nodules in patients with chronic viral hepatitis which undergo at magnetic resonance imaging (MRI) using gadoxetic acid. Methods and materials We evaluated 58 patients with hepatic nodules at least 1 cm in diameter detected by ultrasound who underwent liver MRI including NG-3D T1W-GRE sequences and breath hold T1-weighted gradient-echo sequences with different flip angles(FA) at 10-25-40° after contrast administration of gadoxetic acid at magnetic scanner operating at1.5 Tesla. Image quality and relative hepatic and nodular enhancement were evaluated by three blinded reviewers. Results In these patients, image quality of NG-3D T1W-GRE was assessed significantly better than quality of BHT1W- GRE (P < 0.005) and relative enhancement was significantly higher than that of BH- T1W-GRE ( P

More than 700 anthocyanins are described so far, and many different sources are rich in these natural pigments. During the last few years, researchers have been focusing of strategies to recover and purify anthocyanins, from simple liquid-liquid extractions to more advanced supercritical CO2 extractions, however, with such a huge number of different sources, it’s extremely hard to get a simple and fast methodology that fits several sources, not only by the structural nature of the anthocyanins but also by the presence of specific groups of natural compounds. Using simple methodologies like solid-phase extraction resins represents a powerful economical and efficiency strategy. In this work, we tested several sources of structurally distinct anthocyanins, including purple basil, purple cabbage, purple sweet potato, butterfly pea flower, cornflower and wild pansy, in different resins to assess their efficiency in the obtention of anthocyanin-pure extracts. The results showed us that the combination of oasis HLB® resin followed by a cation-exchange SPE with DSC-MCAX® resulted in high-purity anthocyanin extracts for all the cases.

The effect of ceria doping of (ZrO2)1-x(Sm2O3)x crystals on their phase composition, microhardness and fracture toughness has been studied. The (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 crystals (where x = 0.032, 0.037 and 0.04) have been grown using directional melt crystallization in cold skull. The phase composition and structure of the crystals have been studied using X-ray diffraction, TEM and Raman spectroscopy. The mechanical properties such as microhardness and fracture toughness have been studied using Vickers indentation. It has been shown that the (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 solid solution crystals contain both Се4+ and Се3+ ions. Phase analysis data suggest that СеО2 doping increases the tetragonality degree of the transformable t phase and reduces the tetragonality degree of the non-transformable t' phase as compared to the (ZrO2)1-x(Sm2O3)x crystals. As a result, the t→m phase transition triggered by the indentation-induced stress in the СеО2 doped crystals is more intense and covers greater regions. СеО2 doping of the solid solutions increases the fracture toughness of all the crystals studied whereas the microhardness of the crystals changes but slightly. СеО2 doping of the (ZrO2)1-х(Sm2O3)х solid solutions in the experimental concentration range does not improve the high-temperature phase stability of the crystals and does not prevent high-temperature degradation of their fracture toughness.

A phase 1-2, prospective, multicenter, randomized, open-label clinical trial (Code RPCEC00000382, https://rpcec.sld.cu/trials/RPCEC00000382-En/), with parallel groups, involving 1161 participants was designed to assess safety and immunogenicity of two Cuban COVID-19 vaccines (Mambisa and Abdala) in boosting COVID-19 immunity of convalescent adults after receiving one dose of either vaccine. The main safety outcome was severe vaccination adverse events occurring in &lt;5% of vaccinees. Main immunogenicity success endpoints were ≥4-fold anti-RBD IgG seroconversion or ≥20% increase in ACE2-RBD inhibitory antibodies in &gt;55% of vaccinees in Phase 1 and &gt;70% in Phase 2. Neutralizing antibody titers against SARS-CoV-2 variants were evaluated. Both vaccines were safe; no deaths or severe adverse events occurred. Mild intensity adverse events were the most frequent (&gt;73%); headache predominated for both vaccines. Phase 1 responders were 83.3% (p = 0.0018) for Abdala. Mambisa showed similar results. Phase 2 responders were 88.6% for Abdala (p &lt;0.0001) and 74.2% for Mambisa (p = 0.0412). In both phases, anti-RBD IgG titers, inhibition percentages and neutralizing antibody titers increased significantly after the booster dose. Both vaccines were safe and their immunogenicity surpassed the study endpoints.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

It is well established that the reaction cycles involving some halogenated alkanes (so-called ozone-depleting substances, ODS) contribute to the depletion of ozone in the stratosphere, thus causing the Montreal Protocol (initially signed in 1987) and later amendments. The Protocol called for the scheduled phase-out of ODS, including chlorofluorocarbons (CFC), hydrochloro-fluorocarbons (HCFC), carbon tetrachloride (CCl4), halon, methyl chloroform (CH3CCl3), me-thyl chloride (CH3Cl), and even hydrofluorocarbons (HFCs). In view of the urgent importance of ozone layer protection to the globally ecological environment, the Taiwan government took regulatory actions on reducing ODS consumption since 1993 by the joint-venture of the central competent authorities. Under the regulatory requirements and the industry’s efforts by adopt-ing the alternatives to ODS and abatement technologies, the phase-out of some ODS (i.e., CFC, CCl4, halon, and CH3CCl3) have been achieved prior to 2010. The consumptions of HCFCs and methyl chloride have been significantly declined over the past three decades (1993-2022). However, HFC emission indicated a V-type variation during the period. Due to the local pro-duction and extensive use of HFC in Taiwan, its emissions increased from 663 kilotons of carbon dioxide equivalents (CO2eq) in 1993 to 2,330 kilotons of CO2eq in 2001, and then decreased to 373 kilotons of CO2eq in 2011. Since then, the emissions of HFC largely used as the alternatives to ODS showed an upward trend, increasing to 1,555 kilotons of CO2eq in 2022. To be in compliance with the Kigali Amendment (KA-2015) to the Montreal Protocol for mitigating global warming, the Taiwan government has taken regulatory actions in reducing the consumption of some HFC substances with high global warming potential (GWP) under the authorization of the Climate Change Response Act in 2023, aiming at the baseline consumption in 2024 by 80 % reduction by 2045.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The endometrium, the inner mucosal lining of the uterus, undergoes complex molecular and cellular changes across the menstrual cycle in preparation for embryo implantation. Transcrip-tome-wide analyses have mainly been utilized to study the endometrial receptivity, the prerequisite for successful implantation, with most of the studies, so far, comparing the endometrial transcriptomes between (i) secretory versus proliferative endometrium or (ii) mid-secretory versus early-secretory endometrium. In the current study, we provide the complete transcriptome description of the endometrium across the entire menstrual cycle and, for the first time, comprehensively characterize the proliferative phase of the endometrium. Our temporal transcriptome analysis includes five time points: mid-proliferative, late-proliferative (peri-ovulatory phase), early-secretory, mid-secretory, and late-secretory phases. Thus, we exhaustively unveil the transitions between the consecutive proliferative and secretory phases, highlighting their unique gene expression profiles and possible distinct biological functions. Transcriptome analysis reveals many differentially expressed genes (DEGs) across the menstrual cycle, most of which are phase-specific. As an example of the coordinated gene activity, the expression profile of his-tone-encoding genes within the HIST cluster on chromosome 6 showed an increase in cluster activity during the late-proliferative and a decline during the mid-secretory phase. Moreover, numerous DEGs are shared among all phases. In conclusion, in the current study, we delineate the endometrial proliferative phase-centered view of transcriptome dynamics across the menstrual cycle. Data analysis highlights significant transcriptomic and functional changes occurring during the late-proliferative phase – an essential transition point from the proliferative to the secretory phase. Future studies should explore how the biology of the late-proliferative phase endometrium impacts the achievement of mid-secretory endometrial receptivity or contributes to molecular aberrations leading to embryo implantation failure.

(1) Background: The aim of this investigation is to determine the effect of archwires’ deflection on the temperature transitions driving the austenite to martensite transformation (and vice versa) and the force released by NiTi and CuNiTi orthodontic wires. (2) Methods: Round cross-section archwires have been investigated. The calorimetric approach has been used for measuring transition temperatures occurring in the unstressed (e.g. undeflected) state of the wires. Static Thermo-mechanical analysis in a temperature controlled wet environment has been performed in the range of temperature between 5°C and 55°C for measuring temperature transitions occurring in highly deflected archwires in conjunction with the force released by these wires. (3) Results: Plateau forces investigated in Part I and those reported in the literature describes the wire’s behaviour only at deflection levels close to the end point of the force plateau extension detected at 37°C. Upon heating or cooling, the austenite finish (Af) transition temperature and the martensite start (Ms) temperature largely depends on the deflection level for both NiTi and CuNiTi. (4) Conclusions: The plateau force levels at 37°C, broadly reported in the literature, only represent the lower boundary force that a superelastic wire releases at 37°C above its elastic limit. For both NiTi and CuNiTi, plateau force levels at 37°C can be predicted by the static TMA profile matching the end point of the force plateau extension. Transition temperatures in largely deflected wires are significantly higher than those determined through the calorimetric approach.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

The massive use of electronic equipment has raised concerns about electromagnetic (EM) pollution, leading to increased attention to EM shielding in both civil and military applications. EM absorption materials play a crucial role in reducing the energy of microwaves projected onto their surface. In this work, we propose a novel OTA (over-the-air) antenna test method to evaluate and analyze the functionality of EM absorption materials. This method offers a new and practical way to assess the effectiveness of these materials. Measured results indicate that the presence of the EM absorption material led to a decrease in antenna gain of approximately 2-3 dB, a reduction in efficiency of more than 10-15%, and a smaller radiation pattern during the actual testing process. These findings highlight the impact of EM absorption materials on antenna performance. Compared to the traditional S-parameter testing method, the gain comparison testing method exhibits the advantages of higher accuracy and simpler operation in the lower frequency experiment.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

This chapter explores the pivotal role of maize (Zea mays L.) in global nutrition, emphasizing its status as a staple food worldwide. It discusses maize's complex nutritional profile, including macronutrients, micronutrients, and dietary fiber. The chapter also covers biofortification efforts to enhance maize with essential nutrients, addresses nutritional concerns related to maize-centric diets, and explores genetic modification and agronomic strategies to boost nutrient-rich maize yields. Additionally, it delves into maize processing traditions, nutrient retention techniques, and the importance of promoting nutrient-rich maize varieties. The chapter outlines post-harvest strategies to combat nutrient loss and prevent contamination while emphasizing the significance of consumer education and diverse diets. Case studies illustrate the impact of improved maize nutrition and provide replicable strategies. The chapter concludes by considering emerging research and technology, identifying challenges, and proposing solutions to enhance maize's nutritional value in the future.

This systematic review examines the potential of digital language learning in contributing to students' cognitive gains. The study reviews existing research on the relationship between digital language learning and cognitive benefits, with a focus on enhanced problem-solving skills, memory, and multitasking ability. The findings indicate that higher levels of digital competences correlate positively with language proficiency outcomes, suggesting that participants with greater digital skills achieve better language learning outcomes. Digital technologies offer interactive and engaging methods of learning, which can positively impact retention and understanding. However, the study also acknowledges the limitations of digital foreign language learning, such as the lack of face-to-face interaction and the need for high motivation and discipline. The research questions explored in this study are: (1) Does digital language learning contribute to cognitive gains in foreign language education? and (2) What are the pedagogical implications for cognitive improvement in digital foreign language education? The study employs the Preferred Reporting Items for Systematic Reviews and Meta-analyses (PRISMA) methodology to identify and analyze relevant research articles. The results of the review suggest that working with printed texts may be more effective for cognitive gains compared to electronic texts. Additionally, implementing more senses through digital language education appears to be beneficial for cognitive gains. The article concludes by discussing the implications of these findings and the need for further research in this area.

Background: Changes in body weight are associated with the regulation of DNA methylation (DNAm). In this study, we investigated the associations between maternal gestational weight gain-related DNAm and foetal and neonatal body composition. Methods: Brazilian pregnant women from the Araraquara Cohort Study were followed up during pregnancy, delivery, and after hospital discharge. Women with normal pre-pregnancy BMI were allocated to two groups: adequate gestational weight gain (AGWG, n=45) and excessive gestational weight gain (EGWG, n=30). Foetal and neonatal body composition was evaluated by ultrasound and plethysmography, respectively. DNAm was assessed in maternal blood using Illumina Infinium MethylationEPIC BeadChip arrays. Linear regression models were used to explore the associations between DNAm and foetal and neonatal body composition. Results: Maternal weight, GWG, neonatal weight, and fat mass were higher in the EGWG group. Analysis of DNAm identified 46 differentially methyl-ated positions and 11 differentially methylated regions (DMRs) between the EGWG and AGWG groups. Nine human phenotypes were enriched for these 11 DMRs located in 13 genes (EMILIN1, HOXA5, CPT1B, CLDN9, ZFP57, BRCA1, POU5F1, ANKRD33, HLA-B, RANBP17, ZMYND11, DIP2C, TMEM232), highlighting the terms insulin resistance, and hyperglycaemia. Maternal DNAm was associated with foetal total thigh and arm tissues and subcutaneous thigh and arm fat, as well as with neonatal fat mass percentage and fat mass. Conclusion: The methylation pat-tern in the EGWG group indicated a risk for developing chronic diseases and involvement of ma-ternal DNAm in foetal lean and fat mass and in neonatal fat mass.

This study explores into a comprehensive examination of an optical cavity system that integrates Raman and Yb-doped gain media, with a focus on understanding their interactions. The research implies a characterization of each gain medium within the cavity while subjecting them to diverse co-pumping conditions with the other. When the Raman-lasing cavity is co-pumped by exciting the Yb-doped section, the resulting composite laser exhibits significant threshold reductions and there is an optimal co-pumping regime that enhances energy transfer from pump to Stokes. As for the complementary cavity, where the Yb-doped gain is influenced by the co-pumped Raman gain, at moderate pump powers a light-controlling-light behavior phenomenon arises. Within this regime, the 1064-nm signal suppresses the Yb-generated 1115-nm signal, suggesting potential applications in intracavity optical modulation. For higher pump levels, a cooperative effect emerges whereby both lasers mutually enhance each other. Minor variations in the primary 974-nm pump power, even by just a few milliwatts, result in significant capabilities for switching or modulating the Stokes signal. Under these conditions of mutual enhancement, the hybrid optical system validates notable improvements regarding energy transfer efficiency and threshold reduction. This research provides valuable insights into the intricate dynamics of optical cavity systems and reveals promising avenues for applications in advanced optical modulation technologies.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

Simple summary This reassessment of the findings from our Phase I/II study seeks to evaluate the effectiveness of SBRT for treating local intermediate-high risk prostate cancer in the absence of androgen-deprivation therapy due to patient’s refusal, with a median follow-up of 6.5 years. Our primary focus is on analysing the treated areas compared to recurrence patterns in the seven patients who experienced local relapse. Additionally, we provide updated data on late toxicities of grade 2 or higher, both genitourinary and gastrointestinal. Abstract Objectives: We investigated spatial patterns between primary and recurrent tumor sites and assessed long-term toxicity after dose escalation stereotactic body radiation therapy (SBRT) to the dominant intraprostatic nodule (DIN). Materials and methods: In 33 patients with intermediate-high risk prostate cancer (PCa), doses up to 50 Gy were administered to the DIN. Recurrence sites were determined and compared to the original tumor development sites through multiparametric MRI and 68Ga-labelled prostate-specific membrane antigen (PSMA) positron emission tomography/computed tomography (68Ga-PSMA-PET/CT) images. Overlap rates, categorized as 75% or higher for full overlap, and 25-74% for partial overlap, were assessed. Long-term toxicity is reported. Results: All patients completed treatment, with only one receiving concomitant androgen deprivation therapy (ADT). Recurrences were diagnosed after a median of 33 months (range: 17-76 months), affecting 13 out of 33 patients (39.4%). Intraprostatic recurrences occurred in 7 patients (21%), with ≥ 75% overlap in two, a partial overlap in another two, and no overlap in the remaining three patient. Notably, 5 patients with intra-prostatic recurrences had synchronous bone and/or lymph node metastases, while six patients had isolated bone or lymph node metastasis without intraprostatic recurrences. Extended follow-up revealed grade 2 or higher late GU and GI toxicity in 18% (n=6) and 6% (n=2) of the patients. Conclusions: Among patients with intermediate-high risk PCa undergoing focal dose-escalated SBRT without ADT, DIN recurrences were infrequent. When present, these recurrences were typically located at the original site or adjacent to the initial tumor. Conversely, relapses beyond the DIN and in extra-prostatic (metastatic) sites were prevalent, underscoring the significance of systemic ADT in managing this patient population. Advances in knowledge: focal dose escalated prostate SBRT prevented recurrences in the dominant nodule, however extra-prostatic recurrence sites were frequent.

This study aimed to evaluate the impact of selected pregnancy pathologies statistically depending on overweight/obesity and excessive maternal weight gain during pregnancy on women who gave birth in the years 2013–2015 at the Second Department of Gynecology and Obstetrics at the University Hospital in Bratislava, Slovakia. In a retrospective study, we analyzed data gathered from the sample, which consisted of 7,122 women. Our results indicate a positive statistical dependency of the groups of women with overweight and obesity and gestational hypertension (adjusted odds ratio [AOR]=15.3; 95% CI 9.0−25.8 for obesity), preeclampsia (AOR=3.4; 95% CI 1.9−6.0 for overweight and AOR=13.2; 95% CI 7.7−22.5 for obesity), and gestational diabetes mellitus (AOR=1.9; 95% CI 1.2−2.9 for overweight and AOR=2.4; 95% CI 1.4−4.0 for obesity). A higher incidence of pregnancies terminated by cesarean section was observed in the group of obese women. Gestational weight gain above the IOM (the Institute of Medicine) recommendations was associated with a higher risk of pregnancy terminated by C-section (AOR=1.2; 95% CI 1.0−1.3), gestational hypertension (AOR=1.7; 95% CI 1.0−2.7), and infant macrosomia (AOR=1.7; 95% CI 1.3−2.1). Overweight and obesity during pregnancy significantly contribute to the development of pregnancy pathologies and increased incidence of cesarean section. Systematic efforts to reduce weight before pregnancy through pre-pregnancy dietary counseling, regular physical activity, and healthy lifestyle should be the primary goal.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

Gain-scheduled autopilots have emerged as a dominant strategy to achieve adaptive control of coupled, non-linear engineering complexities, owing to an ability to adapt to changing operational conditions and uncertainties. This study focuses on utilizing bilinear interpolation of gain-scheduled autopilots, emphasizing enhanced system performance and robustness. Through a comprehensive investigation and comparative analysis using three disparate cases, advantages over conventional methods are revealed. Strengths and weaknesses of both simple and specialized variants (such as linear, and real-time gain-scheduling) are introduced. Three missile guidance case–studies utilize simulation time and miss distance figures of merit. Potential to achieve precise control across various mission scenarios, while ensuring reduced computational complexity is revealed by nearly two–hundred percent improved missile miss distances with comparable distances traveled and slightly improved computational burden.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

Magnetic quantum oscillations (MQO) are traditionally applied to investigate the electronic structure of metals. In layered quasi-two-dimensional (Q2D) materials the MQO have several qualitative features giving additional useful information, provided their theoretical description is developed. Within the framework of the Kubo formula and the self-consistent Born approximation, we reconsider the phase of beats in the amplitude of Shubnikov oscillations of interlayer conductivity in Q2D metals. We show that the phase shift of beats of the Shubnikov (conductivity) oscillations relative to the de Haas - van Alphen (magnetization) oscillations is larger than expected previously and, under certain conditions, can reach the value of π/2, as observed experimentally. We explain the phase inversion of MQO during the 3D - 2D crossover and predict the decrease of relative MQO amplitude of interlayer magnetoresistance in a strong magnetic field, larger than the beat frequency.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Here we performed a comparative experimental analysis by EPR spectroscopy of the intensity of nitric oxide (NO) production and copper content in the injured and uninjured areas of the frontal lobes and the hippocampus of the brain of male Wistar rats, after modeling of combined brain and spinal cord injury. Brain and spinal cord injury were modelled by local destruction of the left precentral region of the brain using a stylet followed by hemorrhage injury at the level of the first lumbar vertebra of the spinal cord. We found a significant decrease in NO production 7 days after injury modeling in the injured and uninjured (contralateral) brain regions, but the copper content remained unchanged one week after injury modeling. Thus, combined brain and spinal cord injury is not accompanied by a radical change in the activity of the antioxidant system in the brain, which is also confirmed by the absence of changes in NO production and copper content in the hippocampus.

A drug repositioning effort supported the possible use of the anti-HIV drug etravirine as a treatment for Friedreich Ataxia (FRDA). Etravirine increases frataxin protein and corrects the biochemical defects in cells derived from FRDA patients. Because of these findings, and since etravirine displays a favorable safety profile, we conducted this pilot open-label phase 2 clinical trial assessing the safety and potential efficacy of etravirine in FRDA patients. Thirty-five patients were stratified into 3 severity groups and randomized to etravirine 200 mg/day or 400 mg/day. They were treated for 4 months. Efficacy endpoints were represented by changes in peak oxygen uptake and workload as measured by incremental exercise test, SARA score, cardiac measures, measures of QoL and disability. Data were collected 4 months before the start of the treatment (T-4), at the start (T0), at the end (T4) and 4 months after the termination of the treatment (T+4). Etravirine was well tolerated. Etravirine completely stopped the progression of the SARA score during the 4-months treatment period, compared to the 4 months pre and post treatment. It increased peak workload, while the improvement of peak oxygen uptake was not statistically significant. No changes in the cardiac measures were observed. Health and QoL measures showed a worsening at the suspension of the drug. In this open trial etravirine significantly improved neurological function and was generally safe and reasonably tolerated. This suggests that etravirine represents a potential therapeutic agent in FRDA deserving testing in a randomized placebo controlled clinical trial.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

The potential of generalized machine learning models developed for crop water estimation was examined in the current study. Extreme Gradient Boosting (XGBoost), Gradient Boosting Machine (GBM), and Random Forest (RF) are three ensembled machine learning models that were developed using all of the data from a single location from 1976 to 2017 and then immediately applied at eleven different locations without the need for any local calibration. For the test period of January 2018 to June 2020, the model's capacity to estimate the numerical values of crop water requirement (Pen-man-Monteith (PM) ETo values) was assessed. In comparison to the GBM and RF models, the XGBoost model outperformed them both marginally and significantly. The estimate's weighted standard error was smaller than 0.85 mm/day, and the model's effectiveness varied from 96% to 99% across various locations. The model's strong performance was indicated by the decreased noise-to-signal ratio. A real-time water management system at the regional level can be seamlessly linked with this type of model due to its accuracy in estimating crop water requirements and its capacity to generalize.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

In this research paper, a high gain transformer less inverter modeling which is used for the smart grid technology or as the stand alone for home appliances is proposed. The proposed transformer less topology provides a higher voltage gain, low cost, small size and simple control stand alone transformer less inverter for home appliances. The above inverter is modeled by using software which is known as MATLAB/ Simulimk.

Cheating prevention in online exams is often hard and costly to tackle with proctoring, and it even sometimes involves privacy issues, especially in social distancing due to the pandemic of COVID-19. Here we propose a low-cost and privacy-preserving anti-cheating scheme by programmatically minimizing the cheating gain. A novel anti-cheating scheme we developed theoretically ensures that the cheating gain of all students can be controlled below a desired level aided by the prior knowledge of students’ abilities and a proper assignment of question sequences. Furthermore, a heuristic greedy algorithm we developed can refine an assignment of questions from a cyclic pool of question sequences to efficiently reduce the cheating gain. Compared to the integer linear programming and min-max matching methods in a small-scale simulation, our heuristic algorithm provides results close to the optimal solutions offered by the two standard discrete optimization methods. Hence, our anti-cheating approach could potentially be a cost-effective solution to the well-known cheating problem even without proctoring.

In the industrial sector, the financial gain is generally considered at the cost of environmental degradation. The environmental protection and economic benefit are common conflicting objectives in many optimization problems. In any multi-criteria problem, the most challenging part is to optimize the conflicting goals. But if these objectives become non-conflicting, then the problem can be solved with ease. This paper is all about minimizing the environmental impact of industrial processes while maximizing the net economic benefit. There is a general misconception of linking the environmental protection with a financial loss. This is not always true; the Eco-Efficiency or Cleaner Production Technology (CPT) is a perfect example to disprove this notion. Economics of CPT regarding water savings for the textile-processing sector in Pakistan has been analyzed in this paper. Changes in water use before and after the implementation of water conserving technologies in the textile sector of Pakistan from a study conducted by the Cleaner Production Institute (CPI) are utilized to perform a cost-benefit analysis. Direct financial benefits that could be achieved through the application of these technologies are presented only. Other environmental benefits, though not described here, are of no less importance. The study results reveal that very high potential of water savings exists for most of the investments on CPT.

In this paper, the neural network is developed for solving the inverse photoacoustic problem aiming to estimate thermo-elastic properties and thickness of a semiconductor sample. The idea was that these sample properties be estimated from the phase characteristic because the phase measurements are more sensitive. The neural network has been trained on a large basis of photoacoustic phases calculated from a theoretical Si n-type model in the range of 20Hz to 20kHz, on which random Gaussian noise has been applied. It is shown that high accuracy and precision could be reached in solving of inverse photoacoustic problem using only phase measurement.

Weight gain affects about 10-20% of patients after bariatric surgery. It is a phenomenon that is difficult to understand and to intervene due to its complexity and etiological heterogeneity. In the present study, we investigated, from a network analysis perspective, the associations between weight regain, psychological, sociodemographic factors and physical activity in patients undergoing bariatric surgery. The sample consisted of 124 patients, of both sexes, aged 39 ± 9.1 years, who had undergone surgical intervention for more than 18 months. After voluntary consent, respondents answered questionnaires and instruments directly on the Google Forms platform. The results indicated that weight gain was negatively associated with the items of depression, anxiety and stress, binge eating and with the dimensions of the personality questionnaire (negative affectivity -0.182; detachment -0.078; antagonism -0.107; disinterest - 0.198 and psychoticism -0.158). The centrality indicators revealed that the characteristics of disinterest and negative affectivity and most of the items on the depression, anxiety and stress scale had a greater expected influence (values ​​from 1,043 to 1,502), indicating that these are the most sensitive variables to intervention and who need more attention from health professionals.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

Abstract Safflower (Carthamus tinctorius L.) is a multipurpose minor crop consumed by developed and developing nations around the world with a limited research fund and genetic resources. Genomic selection (GS) is an effective modern breeding tool which could help to fast track the genetic diversity preserved in genebank collections to facilitate rapid and efficient germplasm improvement and variety development. In the present study, we simulated four GS strategies to compare genetic gains and inbreeding rates during breeding cycles in a safflower recurrent selection breeding program targeting grain yield (GY) and seed oil content (OL). We observed positive genetic gains over cycles in all four GS strategies, where the first cycle delivered the largest genetic gain. Single traits GS strategies had the greatest gain for the target trait but with very limited genetic improvement for the other trait. Simultaneous selection for GY and OL via index indicated higher gains for both traits than crossing between the two single trait independent culling strategies. The the multi-trati GS strategy with inbreeding control (GS_GY+OL+Rel) showed lower inbreeding rate but similar gain compared to GS_GY+OL (without inbreeding control) after few cycles. Our finding lay the foundation for the future safflower GS breeding.

This paper presents a robust and efficient fault detection and diagnosis framework for handling small faults and oscillations in synchronous generator (SG) systems. The proposed framework utilizes the Brunovsky form representation of nonlinear systems to mathematically formulate the fault detection problem. A differential-flatness model of SG systems is provided to meet the conditions of the Brunovsky form representation. A combination of high-gain observer and group method of data handling neural network is employed to estimate the trajectory of the system and to learn/ approximate the fault and uncertainties associated functions. The fault detection mechanism is developed based on output residual generation and monitoring so that any unfavourable oscillation and/or fault occurrence can be detected rapidly. Accordingly, an average L1-norm criterion is proposed for rapid decision making of faulty situations. The performance of the proposed framework is investigated for two benchmark scenarios which are actuation fault and fault impact on system dynamics. The simulation results demonstrate the capacity and effectiveness of the proposed solution for rapid fault detection and diagnosis in SG systems in practice, and thus enhancing service maintenance, protection, and life cycle of SGs.

An imbalance in any metabolic system can be traced to its homeostasis. When homeostatic environment is not attainable then there will be a response from the body. A new shift has emerged, “the negative feedback effect of high fructose consumption;” more pain than gain. The human metabolic system daily combat fructose sugar metabolism which emanates from high consumption. This inadvently lead to a chronological series of complications arising from the feedback. These feedbacks play pivotal roles in skeletal muscle damage and other body frameworks, it also fosters toxic advanced glycation end products (AGEs), factors that impose and inflict damaging effects to the body`s energy currency and serious threat to health. These damages are missed or overlooked because of early nonspecific physiological symptoms. High level of fructose has both long- and short-term effects on human metabolic processes. These effects which are majorly through the production of reactive oxygen species (ROS) and other free radicals, are felt in the disruption of biomolecules such as causing DNA mutation, lipid peroxidation etc. these effects in turn lead to various diseases such as cancer, diabetes, atherosclerosis, and other health issues. In this review, we will focus on the damaging effects this sugar has on human health and the present solutions being applied. We will also look at the next step in combatting and controlling these negative feedbacks.

Background: Early diagnosis of postoperative complications is an urgent task, allowing timely prescribing of appropriate therapy and reducing the cost of patient treatment. Prognostic models based on various data could help in the early diagnosis of postoperative complications after cardiac surgery. Objectives: The purpose of the study was to determine whether an integrated approach based on clinical data along with metabolites and biomarkers had greater predictive value than the models built on less data. Methods: The study included patients (n=62) admitted for planned cardiac surgery (coronary artery bypass grafting with cardiopulmonary bypass), who were retrospectively divided into two groups depending on the presence (n=26) or absence (n=36) of postoperative complications of all types. Clinical and laboratory data on the first day after surgery were analyzed. Additionally, patients' blood samples were collected before and on the first day after surgery to determine biomarkers (interleukin-6, procalcitonin, NT-proBNP, high-sensitivity troponin T) and metabolites (8 aromatic and 2 dicarboxylic acids were detected using gas chromatography-mass spectrometry). Results: Patients before surgery, compared with healthy donors, differed in the concentration of metabolites (p &lt; 0.05), and had concentrations of a number of biomarkers exceeding the corresponding reference values. Multivariate PLS-DA models, predicting the presence or absence of postoperative complications, were built using clinical data (ROC-AUC=0.71), concentrations of metabolites and biomarkers (ROC-AUC=0.60), and the entire data set (ROC-AUC=0.75). For comparison we built univariate models using the EuroScore2 (ROC-AUC=0.59) and SOFA (ROC-AUC=0.76) scales; concentrations of lactate (ROC-AUC=0.71), the dynamic changes of 4-hydroxyphenyllactic acid (ROC-AUC=0.69), and the sum of three sepsis-associated metabolites (ROC-AUC=0.70). The proposed complex model using entire data set was comparable to the SOFA scale, which confirms the expediency of searching for new predictive models based on a variety of factors.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Three-phase induction motors play a key role in industrial operations. However, their failure can result in serious operational problems. This study focuses on the early identification of faults through accurate diagnosis and classification of faults in three-phase induction motors, using artificial intelligence techniques, by analyzing current, temperature, and vibration signals. Experiments were conducted on a test bench, simulating real operating conditions, including stator phase unbalance, bearing damage and shaft unbalance. To classify the faults, an Auto-Regressive Neural Network with Exogenous Inputs (NARX) was developed. The parameters of this network were determined through a process of selecting the best network, using the scanning method with multiple training and validation iterations, with the introduction of new data. The results of these tests showed that the network had excellent generalization in all the situations evaluated, achieving the following accuracy rates: Motor without fault = 94.2%, Unbalance fault = 95%, Bearings with fault =98% and Stator with fault = 95%.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

The aim of this retrospective study was to compare the clinical outcomes of treating isolated surgical neck fractures of the humerus using either the intramedullary nail or the MIROS (Minimally Invasive Reduction and Osteosynthesis System®) system. The study included 42 patients who underwent surgical treatment at the Polyclinic from January 2014 to June 2020. The results indicated that both treatments were effective; however, the MIROS system exhibited a higher complication rate. Intramedullary nailing was more reliable, thus recommended as the primary treatment method. This study underscores the importance of selecting the appropriate fixation technique to minimize complications and enhance patient outcomes.

Mutations in the “guardian of the genome” TP53 predominate in solid tumors. In addition to loss of tumor suppressor activity, a specific subset of missense mutations confers additional oncogenic properties. These “gain-of-function” (GOF) mutations portend poor prognosis across cancer types regardless of treatment. Our objective in this study was to identify novel therapeutic opportunities to overcome the deleterious effects of GOF TP53 mutants. Using gynecologic cancer cell lines with known TP53 mutational status, we established that treatment with a proteasome inhibitor induced cell death in cells with two recurrent GOF TP53 mutations (R175H and R248Q), and addition of a histone deacetylase inhibitor (HDACi) enhanced this effect. By contrast, p53-null cancer cells were relatively resistant to the combination. Towards understanding the mechanism, we found that proteasome inhibition promotes apoptosis of cells with TP53 GOF mutations, potentially through induction of the unfolded protein response. In line with the reported hyperstabilization of GOF p53 protein, cells treated with HDACi exhibited reduced levels of p53 protein. Together, these data form the basis for future clinical studies examining therapeutic efficacy in a preselected patient population with GOF TP53 mutations.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Excess nitrogen in agricultural drainage poses a serious threat to the water quality safety of the Yellow River basin. Utilizing aquatic plants to modify the rhizosphere microbial community structure and facilitate nitrogen transformation is a crucial strategy for mitigating regional water eutrophication. Our results revealed that the denitrification rate (DR), dissimilatory nitrate reduction to ammonium rate (DNRAR) and nitrogen fixation rate (NFR) of rhizosphere sediments exhibited a significant increase in artificially cultivated ditch. Compared with those in natural ditches, the richness of the bacterial community and the relative abundances of Bacteroidota, Verrucomicrobiota, Firmicutes, Anaeromyxobacter and Geobacter, which are involved mainly in the nitrogen cycle, in the rhizosphere sediments of artificially cultivated ditch were significantly greater due to improvements in environmental conditions. In artificially cultivated ditch, the dominant functional genes affecting DRNARs in the rhizosphere sediments of P. australis were nrfC and nrfA, while DRs were driven mainly by norB and napA, which were influenced by the nitrogen and carbon levels; and the dominant functional genes affecting NFRs in the rhizosphere sediments of T. orientalis were nifD, nifK and nifH. Our results provide a scientific basis for the use of aquatic plants for mitigating excess nitrogen levels in agricultural drainage.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.