Refractory materials are used worldwide in process equipment. However, gaseous and liquid process products penetrate the surface layer, and deep into the volume of refractories destructing rather expensive constructions complicated to repair. To address this challenge, there is a need to develop protective coatings for refractory that can limit the penetration of working media and extend their operational lifespan. In this work, the application of gas-dynamic cold spraying (CGDS) to produce a coating on the refractory using fine titanium dioxide (TiO2) particles is explored. These particles are accelerated within a nitrogen flow, passing through a Laval nozzle, and then sprayed onto a fireclay surface. The mechanisms of particle deposition and layer formation on porous surfaces through experiments and numerical simulations were investigated. The geometry of a typical refractory pore was determined, which was then incorporated into Computational Fluid Dynamics (CFD) simulations to model the cold spraying process of porous substrates. As a result, the influence of the particle size on its velocity and angle of penetration into pores was established. Experimental findings demonstrate the effective closure of pores and the formation of a particle layer on the refractory surface. Furthermore, the nanoindentation tests for the refractory samples showcase capabilities for checking coating thickness for porous materials.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

The main goal was to investigate the ability of non-thermal plasma reactor with gliding arc discharge to remove the diesel exhaust particulates (DEPs). A conventional knifed-shaped LTP GA reactor was utilized. Three cases were studied: 140 L/min, 70 L/min and 14 L/min of air drawn through the reactor and diesel exhaust fumes were sampled continuously. They were assayed in terms of concentration and number particle size distribution. The higher the residence time’s, the higher the energy input that may be utilized for DEPs’ removal. Reactor’s performance definitely lowered the concentration of DEPs (250 - 580 nm) and altered their number size distribution. There was no effect on the number concentration, nor on the particle size distribution, of DEP particulates of 10 – 250 nm in size. The effectiveness of DEPs’ removal: Decreasing flow rate from 140 L/min to 70 L/min somehow altered the values. Achieving the airflow of 14 L/min led to a substantial improvement (even to a fourfold increase for 300 – 480 nm particles). Non-thermal plasma reactors with gliding arc discharge may be successfully adapted in the process of DEPs’ treatment. Their performance may be optimized by adjusting the airflow at the inlet of reactor to guarantee the longest aerosol residence times and the highest removal efficiency.

Successful geophysical exploration works in Gucheng-Yaxi area located in Gaochun District, Jiangsu province, China, have been limited partly due to complex geological condition of the area and high artificial noise in data acquired using electrical and electromagnetic methods. In this work, we deployed the new anti-interference spread spectrum induced polarization method (SSIP) and audio magnetotellurics (AMT) method to detect a copper-polymetallic deposit in the area. Two-dimensional (2D) inversion results at Gucheng-Yaxi Area revealed a high chargeability anomalous zone on SSIP profile that coincided with a zone of moderate resistivity located between two resistor bodies on AMT profile. A follow up 1200 meters drill hole was established at this high chargeability-moderate resistivity zone which encountered polymetallic (copper, lead, zinc, gold and silver) mineralization at the depth ≥ 400 m. Drill hole data analysis showed that mineralization occurs interspaced in marble rock mass at varies depth. Furthermore, several low resistivity-weak chargeability sections were revealed and inferred attributed to Cretaceous sediments and faults. These faults are thought to have played critical role in the polymetallic mineralization genesis. In summary, this work demonstrated the successful of application of SSIP and AMT at detecting a metallic deposit in an area with high artificial noise. Hence the geophysical prospection potential of Gucheng-Yaxi area is great.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

The aim of this study was to investigate and effect of application of different conditions of freeze-drying on the kinetics of process and the sorption properties of dried apples. Slices of apple were frozen and subjected to freezing-drying process with different combination of a shelf temperature (-20, 10, 20, 30°C) and pressure (37, 63, 103, 165 Pa). During the freeze-drying, the temperature in the centre of material was recorded. The moisture content in dried material and changes of water content dried apples stored at humidity of 75.3% were obtained. The Midilli et al. model was used to describe drying kinetics of the freeze-drying with good fit. Drying time decreased from 660 (variant with a constant shelf temperature of 30°C, pressure 63 Pa) to 1305 minutes (variant with temperatures −20: 10: 20: 30°C, pressure 63 Pa). For this reason, the most favourable experimental parameters were: temperature of 30°C and pressure of 63 Pa. However, application of these parameters caused higher absorption of water vapour during storage. Therefore, the selection of freeze-drying parameters should also be related to the expected properties of the final product.

Linear alkylbenzene sulfonate (LAS) anionic surfactants are widely used, present in wastewater, and can be discharged causing environmental damage. Without considering biodegradation, sorption and desorption reactions play an important role and depend on the characteristics of the aquifer medium such as the content of organic matter and clay. These processes are modelled with PHREEQC using laboratory-obtained data on columns with an input LAS pulse. LAS adsorption and desorption step experiments carried out in sand columns were also modelled with this software and distribution constants were similar to those obtained for pulse. The values of the starting distribution constant provided by batch tests with sand and agricultural soil mixtures establish the maximum value that must be obtained for column modelling. Distribution constants from column experiments obtained by Freundlich and linear isotherms provided very similar results, the latter with more consistent achievement. The modelling results showed longer elution times in the case of the heavier homologues and with a higher percentage of agricultural soil, which would translate into the great persistence of these compounds in the environment. In the case of soil contamination with wastewater-containing surfactants, these results would allow the development of mitigation strategies for these environmental impacts.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

High-density olive groves, despite their interesting production potential, have several limitations, also due to the high fruit load and the irrigation requirements.The study aimed to evaluate the effects of fruit load and deficit irrigation on oil yield and fruit quality, and on olive chemical composition in a high-density olive grove (cv Sikitita). Our main hypothesis was that the primary metabolism, as influenced by crop load and stress, could modify the accumulation of different phenolic classes.Different fruit loads were generated through flower thinning (66%, 50%, 33%, 0%) and two deficit irrigation treatments (-60%, -75%) were compared to the well-watered control (920 m3/ha).Thinning treatments had a limited effect on oil yield, on the other hand, deficit irrigation caused considerably less oil accumulation in the fruit on all sampling dates.Thinning 66% and deficit irrigation 75% were considered with the control for untargeted metabolomic analysis, considering three sampling dates. 233 different phenolic compounds were annotated. Multivariate HCA results indicated the impact of harvest time on the phenolic profile of olive fruits, yielding two separate clusters grouping t1 and t2 together and apart from t3. Regarding agronomic techniques, they played a differential role in the phenolic profile (supervised OPLS – DA). Fruit load mostly affected flavonoid glycosides. In contrast, the phenolic response to deficit irrigation is more heterogeneous, with phenolic acids (35%), flavonoids (25%), LMW, and other phenols (25%).

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

It is an utmost importance to characterize drug candidates as early in the development pipeline as possible. Appropriate application of the emerging high throughput analytical techniques unlocks the opportunities to obtain experimental data for in vitro absorption, distribution, metabolism and elimination (ADME) profiling of large compound libraries which is crucial for selection of lead compounds. In an usual scenario, only one drug candidate will be selected from thousands of early compounds based on several stability and screening results. A high to medium throughput screening approaches could significantly accelerates the subsequent research and production phases. Traditionally, the analysis of metabolic stability assays heavily relies on high throughput LC-MS/MS techniques to meet with the lead profiling demands. In this study presented an innovative experimental approach that can offer a refreshing alternative. Laser Assisted Rapid Evaporative Ionization Mass Spectrometry (LA-REIMS) is a quick and efficient method for characterizing complex biological samples without laborious sample preparation and chemical separation. Therefore, using an automated LA-REIMS well plate reader as fast as 8 seconds per sample, we assessed the oxidative metabolic stability of active agents using biomimetic metalloporphyrin-based oxidative model reactions at various pH for commercially available drug substances and compared stability measurements with traditional HPLC-DAD-MS results.

Nanling Mountain region is a typical southern hilly region, which plays an important ecological and environmental protection role in China's overall land protection pattern. Based on the remote sensing image data of Longnan City in Nanling Mountain in 2013, 2018 and 2023, this paper interpreted the land use type and analyzed the land use transfer situation by using Land use transfer flow, and Land use transfer matrix. At the same time, based on the remote sensing Ecological index (RSEI) model, the ecological environment quality of Longnan City from 2013 to 2023 was retrieved. The temporal and spatial response model of ecological environment quality to land use transfer in Longnan City from 2013 to 2023 was discussed based on Spatial autocorrelation and Geographic detector. The results show that from 2013 to 2023, the decrease of forest land (16.23km²) and the increase of construction land (13.25km²) were the main land use transfer in Longnan City. The ecological environment index of Longnan City in 2013, 2018 and 2023 was 0.789, 0.917 and 0.872, respectively, showing a trend of "first rising and then decreasing". The ecological environment quality in the north of Longnan City was significantly lower than that in the south, and the poor ecological quality area appeared in and around the northern main urban area, showing a trend of "inward contraction". Forest land, garden land, grassland, cultivated land and water area have a positive impact on ecological environment quality, while traffic land, construction land and other land have a negative impact on ecological environment quality. The response of ecological environment quality to different land use transfer modes is related to the change of the overall ecological environment quality. The interaction between LUCC and other factors had a great impact on the evolution of ecological environment quality in Longnan City.

This study investigates the use of geopolymer technology as an alternative for the management of mine tailings, which is a serious environmental problem in mining environments including that of Arequipa region of Peru. In this study, the mixture of stabilized mine tailings with different percentages of binders (metakaolin and pumice) and their impact on the mechanical, microstructural, and toxicological properties of the synthesized geopolymers were analyzed. The ratios of mine tailings to binder material varied between 100/0 and 0/100. The activation was carried out with an alkaline solution of sodium hydroxide (10M) and sodium silicate (modulus 2.5). 50 mm cubic specimens were fabricated, and 7 mixtures with 3 replicates each were evaluated. The evaluations included compressive strength at 7, 14, 28, and 56 days of curing, chemical analysis by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR), microstructural characterization by Scanning Electron Microscopy (SEM/EDS), thermal behavior by thermogravimetry and differential thermal analysis (TGA/DTA) between 40°C and 1000°C, and toxicological tests by the Toxicity Characteristic Leaching Procedure (TCLP, EPA 1311) to determine the efficiency of immobilization of toxic metals. The results showed good mechanical strength, reaching 25 MPa at 7 days of curing, high microstructural stability with an average pore size of 7.21 μm, and good efficiency in the immobilization of heavy metals in geopolymers composed of 60% - 40% and 70% - 30% of the mine tailings - binders ratio, as the concentrations of As, Cd, Pb, Hg were below the established thresholds, acquiring the classification of non-hazardous materials. Geopolymers with 30 to 50% binder showed good mechanical behavior, microstructural stability, and high efficiency in the immobilization of heavy metals, complying with current regulations. Therefore, these geopolymers are suitable for various applications and in different environmental conditions.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

The study was performed to get the first insight of distribution of the low field volume magnetic susceptibility (MS) throughout the Zagreb city area, based on in-situ field measurements. Most interesting locations were selected for soil sampling and geochemical content was determined using ICP-OES. A geostatistical approach was applied on MS and geochemical results. Median value of 0.245 x 10-3 SI units is proposed to be used as relevant average MS value in Zagreb area. Mean concentrations of heavy metals in Zagreb soils (in µg/g) are: Pb (36.82), Zn (87.77), Cu (30.84), Cd (0.66), Cr (29.04), Co (11.89) and Ni (28.40), being relatively low in comparison with Croatian legislation and with European and world average. Boxplot analyses showed that 45% of studied elements do not show any anomaly, while the rest of elements mostly show only one weak anomaly and they are located at the same sites as MS anomalies. Statistical analysis found significant correlations between MS and following elements: Cd, Co, Fe, Mn, Na, Pb, Sb and Zn. In-situ MS measurements proved to be an efficient tool for initial screening of large areas in terms of elevated heavy elements concentrations, enabling cheap and fast assessment of state of environment.

Although composting has many advantages in the treatment of organic waste, there are still many problems and challenges associated with emissions, like NH3, VOCs, and H2S, as well as greenhouse gases such as CO2, CH4, and N2O. One promising approach to enhancing composting conditions is used of novel analytical methods bad on artificial intelligence. To predict and optimize the emissions (CO, CO2, H2S, NH3) during composting process kinetics thought mathematical models (MM) and machine learning (ML) models were utilized. Data about everyday emissions from laboratory composting with compost’s biochar with different incubation (50, 60, 70 °C) and biochar doses (0, 3, 6, 9, 12, 15% d.m.) were used for MM and ML models selections and training. MM has not been very effective in predicting emissions, (R2 0.1 - 0.9), while ML models such as acritical neural network (ANN, Bayesian Regularized Neural Network; R2 accuracy CO:0,71, CO2:0,81, NH3:0,95, H2S:0,72)) and decision tree (DT, RPART; R2 accuracy CO:0,693, CO2:0,80, NH3:0,93, H2S:0,65) have demonstrated satisfactory results. For the first time the ML models to predict CO and H2S during composting were demonstrated. Further research in a semi-scale and field study composting with biochar is needed to improve the accuracy of developments models.

Danyore Valley area is a new prospect of copper-gold mineralization in the Gilgit-Baltistan province, Kohistan terrane, northern Pakistan. The mineralization is Cu-Au vein-type, localized within quartz veins and controlled by a fracture system mainly trending NW and NE. The host units belong to the Ladakh-Kohistan arc terrane, which covers northern Pakistan and north-western India and mainly comprises Precambrian basement units, Paleozoic to Cenozoic magmatic rocks, and sedimentary strata. The mineralized wall rocks consist of Mesozoic gabbro and diorite, which have undergone an intensive hydrothermal alteration. The study area, Danyore Valley, has yet to be explored. The geological background and mineralization type in literature are scarce. Moreover, the tectonic setting, petrogenesis, age, and magmatic evolution of the gabbro-diorite hosting unit still need to be better understood. Furthermore, the sources of metals and mineralized fluids and the types of mineralization and alteration are also unexplored. This research's contribution presents the field investigation, microscopic observations, whole rock geochemistry (major, trace, and REE), mineral analysis (EPMA), in situ LA–ICP–MS zircon U–Pb age dating, and zircon trace elements data for Danyore Valley Cu-Au prospect of Kohistan Batholith. The current research work's objectives are to (a) constrain the emplacement ages of the Danyore Valley host rocks, (b) determine the petrogenesis and tectonic environment of the gabbro-diorite wall rocks, and (c) identify the mineralization style and alteration patterns of Cu-Au occurrences. The U-Pb isotopic data of studied zircons from Danyore Valley diorite specimens yielded concordia ages from 111.60 ± 0.90 Ma to 112.18 ± 0.74 Ma. Correspondingly, the gabbro rock sample displayed a concordia age of 110.21 ± 0.99 Ma, indicating the crystallization time of the host bodies is mainly the early cretaceous period (∼110 Ma). The findings of this study reveal that the calc-alkaline affinity and arc-like geochemical characteristics of the gabbro and diorite rocks have been characterized by a significant enrichment in large-ion lithophile elements and an apparent depletion in high-field strength elements. The parent magma probably originated from a partial melting process of mantle depletion, and geochemical traits are characteristic of magmas associated with subduction zones. The Danyore Valley area of Kohistan terrane is defined by the existence of several mineralized quartz veins, which are mainly sulfide assemblages. The sulfide ore is mainly comprised of chalcopyrite, pyrite, and bornite, with a smaller amount of covellite and sphalerite and significant traces of gold, which are distributed mainly in sulfides. Copper and gold mineralization of Danyore Valley is associated with phyllic, propylitic, and carbonatization alteration assemblages. Metal-rich quartz veins exhibit a spatial correlation with diorite and gabbro rocks. The discovery of several surface Cu-Au vein-type mineralized areas accompanying outcrops of copper supergene enrichment at the Danyore Valley prospect is significant evidence (predictor patterns) of porphyry-style deposits in the Gilgit district, Kohistan terrane, northern Pakistan. This work also advocates the importance of the Danyore Valley prospect and Kohistan Batholith region for further detailed geological studies.

The cooling of server components has been continuously developed over the past few years in order to meet the increasing cooling requirements of server component manufacturers such as for the processor chips. The growth in performance and power density increases the cooling demand. These requirements directly influence the energy consumption and performance of the hardware. To gain a better understanding of the historical evolution and possible future technology development paths in the field of data center cooling, a patent analysis method was used. The focus is on previous and current development priorities and possible research gaps within the server and computer room levels. The European patent database was selected as data source. To determine relevant patents, the search terms for various cooling technologies were developed iteratively. After the patent extraction for the period 2000 - 2023 (earliest priority year), the search results were classified and analysed. Most of the patents deal with air or liquid cooling. In the area of liquid cooling, the focus was on direct liquid cooling, followed by total liquid cooling. Since 2015 a technological shift from air to liquid cooling can be identified on the level of patent activities. In this context, the patent groups with focus on “constructional details for different types of electric apparatus” and “electrical digital data processing” have the largest share of patents. In addition, the technology focus of the TOP 10 patent applicants was in the field of liquid cooling. In conclusion from the patent analysis, it can be derived that liquid cooling will continue to gain in importance in the future and could also be combined with other approaches in the form of hybrid cooling. However air cooling may still be relevant, even if the main cooling load is handled by liquid-based approaches. At the same time, the optimisation potential for air cooling seems to have been largely exploited in comparison to liquid cooling, as can be seen from the falling number of the patent applications.

A regional modern river-sand geochemical mapping study in the majority of the Timor-Leste territory, including the research area, has not been previously reported. This study demonstrated the potential of modern river sand geochemical mapping as an effective method for lithological mapping, particularly in areas that face challenges in conducting efficient geological fieldwork and have limited geological information. A total of 53 modern river sand samples were collected and analyzed. Before examining the samples using wavelength-dispersive X-ray fluorescence for ten major elements, the loss-on-ignition method was employed. In the Clerec drainage basin, SiO2, CaO, and K2O showed positive correlations, and CaO was positively correlated with MnO. Similarly, in the Sahe River catchment, a positive relationship was observed between CaO, MnO, and TiO2. These findings suggested the presence of quartz, manganese, secondary K-bearing minerals, and secondary Ti-bearing minerals in carbonate rocks that have undergone silicification and other alteration processes. The principal component analysis results corroborated the SiO2/Al2O3 and K2O/Na2O ratios and the ICV findings. PC1 was related to the variations in Ca-poor and Ca-rich rocks; PC2 indicated notable inputs from SiO2-rich and SiO2-poor rocks; and PC3 revealed the possibility of contributions from secondary mineral assemblages related to silicification and low-grade metamorphic processes.

Hot spring is a hot water that is naturally occurring on the surface from the underground and typically heated by subterranean volcanic activity and local underground geothermal gradient. There are four main hot springs in Rwanda such as: Kalisimbi, Bugarama, Kinigi and Nyamyumba former name Gisenyi hot springs. It is often believed that soaking in hot springs is a great way which naturally detox human skin. This research focused on the geochemical analysis of Nyamyumba hot springs located near the fresh water of Lake Kivu for the purpose of understanding its healing capacity and safety. Nyamyumba hot springs are located in the western branch of the East African Rift System and they are located near Virunga volcanic complex, explaining the rising and heating mechanism of water. The concentrations of Sulfate, Iron, Ammonia, Alkalinity, Silica, Phosphate, Salinity, Alkalinity, and Conductivity using standard procedures were measured. The results showed that hot spring water has higher concentrations of chemicals compared to Lake Kivu water and the geochemistry of these hot springs maybe associated with rock dissolution by hot water. The measured parameters were compared with World Health Organization (WHO) standards for recreational waters and it has been identified that Nyamyumba hot springs are safe to use in swimming and therapeutic activities.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Road dust resuspension, especially the particulate matter fraction below 10 µm (PM10), is one of the main air quality management challenges in Europe. Road dust samples were collected from representative streets (suburban and urban) of the city of Viana do Castelo, Portugal. PM10 emission factors (mg veh-1 km-1) ranging from 49 (asphalt) to 330 (cobble stone) were estimated by means of the United Stated Environmental Protection Agency method. Two road dust fractions (< 0.074 mm and from 0.0074 to 1 mm) were characterised for their geochemical, mineralogical and morphological properties. In urban streets, road dusts reveal the contribution from traffic emissions, with higher concentrations of e.g. Cu, Zn, and Pb. In the suburban area, agriculture practices likely contributed to As concentrations of 180 mg kg-1 in the finest road dust fraction. Samples are primarily composed of quartz, but also of muscovite, albite, kaolinite, microcline, Fe-enstatite, graphite and amorphous content. Particle morphology clearly shows the link with natural and traffic related materials, with well-formed minerals and irregular aggregates. The hazard quotient suggests a probability to induce non-carcinogenic adverse health effects in children by ingestion of Zr. Arsenic in the suburban street represents a human health risk of 1.58 x 10-4.

This study explores the potential of piloting desalination plants in a systematic way to evaluate energy improvements in water desalination processes. Pilot tests with the latest generation of reverse osmosis membranes in large desalination plants are becoming increasingly common, as small-scale experiments are carried out on the operation of new generation membranes with better salt rejection and lower energy consumption. This approach aims to achieve optimal water quality standard at the lowest possible cost. In this way, pilot tests are being carried out before the decision is made whether to change the reverse osmosis membranes, as this represents a significant investment. By carrying out these tests, we hope to minimize the risk of making a mistake to ensure the best results in terms of energy consumption, operating costs and reducing the environmental impact while complying with the required water quality. In this case, the Pareto analysis is used to identify the two or three most significant causes whose treatment affects more than 80% of the possible energy improvement to be implemented. This article introduces a novel approach to studying a total of 180 desalination plants at the territorial level in the Canary Islands. The global scarcity of freshwater resources has greatly contributed to the development of desalination technologies, in which reverse osmosis is one of the most widely used and highly regarded methods.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

This research is dedicated to a comprehensive examination of the strengths and weaknesses inherent in the legal and institutional measures designed to protect cultural heritage in the Republic of Serbia from the adverse effects of natural disasters, including earthquakes, landslides, rockfalls, floods, torrents, storms, hail, and forest fires. The study aims to identify the primary challenges and shortcomings within the existing legal and institutional framework, while also pinpointing and analyzing best practices and potential improvements for the protection system. This research posits a preliminary hypothesis suggesting that challenges may exist within the legal and institutional framework for the protection of cultural heritage in the Republic of Serbia, potentially limiting effective response and recovery following natural disasters. This hypothesis will be further developed and adapted based on the analysis of available data. Data collection for this research was conducted through semi-structured interviews with experts and an in-depth analysis of existing documentation. By conducting interviews with experts in the field, the research seeks to gather critical data and insights that will enhance the understanding of these issues and contribute to formulating viable solutions. The analysis and processing of data were carried out using ATLAS.ti software, which facilitated a comprehensive and systematic examination of the collected qualitative information. Furthermore, an assessment of the current capacity of institutions to respond rapidly and effectively to natural disasters that pose a threat to cultural heritage is a key component of the study. The ultimate goal is to develop recommendations that will fortify the legal and institutional framework, thereby bolstering the resilience of cultural heritage sites in Serbia against future natural disasters. The results of the research, highlight significant deficiencies in the legal framework, inadequate institutional capacities and resources, as well as a lack of proper training for crisis response. The need for improved inter-institutional cooperation and the development of technical-logistical resources is emphasized. This paper represents a significant contribution to the understanding and enhancement of the cultural heritage protection system, providing a foundation for further research and strategy development in this area.

Emergency Medical Response Systems (EMRS) play a vital role in delivering medical aid during disasters. In Serbia, these systems encounter several obstacles due to economic limitations, scarce resources, and ongoing healthcare reforms, all of which affect their performance. This study focuses on examining the risk factors and effectiveness of Serbia's EMRS, identifying systemic issues, and proposing enhancements to improve emergency preparedness for disasters. A survey was conducted across healthcare institutions in Serbia to gather comprehensive insights. The survey explored various aspects, including organizational structures, resource distribution, communication systems, and the speed of emergency responses. Statistical methods such as Pearson's correlation, multivariate regression analysis and chi-square tests were utilized to interpret data collected from 172 healthcare institutions. The multivariate regression analysis of EMS organization identified that factors such as the structuring of working hours and shift patterns are significant predictors, contributing to small but meaningful variations in various EMS outcomes. In contrast, other factors, such as financial resources and the availability of ambulance vehicles, showed more targeted significance depending on the specific EMS aspect being analyzed. Institutions with written mass casualty plans and procedures demonstrate superior effectiveness in EMS activities, excelling in resource allocation, operational continuity, and emergency preparedness, particularly through enhanced coordination and specialized systems for managing large-scale emergencies. The findings highlighted notable disparities in how EMRS are organized, with only 46% of institutions having specific emergency departments. Resource limitations were evident, as many facilities operated with minimal staff and outdated equipment. The communication systems revealed weaknesses, with just 54% having established protocols for handling emergency calls. Response times frequently surpassed international standards, which negatively affected patient outcomes. Additionally, the study found training deficiencies, with 68% of participants expressing a need for further education. Serbia’s EMRS are significantly impacted by systemic issues such as insufficient funding, disjointed service delivery, and inadequate training. Overcoming these challenges necessitates a comprehensive approach that includes boosting financial support, implementing standardized protocols, and fostering enhanced collaboration across different sectors.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

With the rapid development of new energy vehicles and the digital electronics industry, the demand for lithium has surged, necessitating advanced lithium extraction technologies. Electrochemical methods, noted for their high selectivity and efficiency in extracting target ions from liquid sources in an environmentally friendly manner, have become increasingly vital. These methods are versatile, applicable in scenarios such as lithium extraction from saline lakes, mother liquor separation, and lithium enrichment. They include electrochemical deintercalation, electrochemical ion pumps, and electrodialysis, each offering unique benefits and challenges depending on the application context. This review provides a detailed exploration of the research progress in lithium extraction using electrochemical methods and discusses future prospects for these technologies, emphasizing their potential to meet the growing demand for lithium.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

The intensive variables, geochemical, mineralogical and petrogenetic constraints of the Iberian rare metal granites, many of them unknown, are presented. It allows to distinguish two main granitic types with contrasting characteristics: Nb-Ta-rich granites and Nb-Ta-poor granites. The former have lower emplacement temperatures, higher water contents and probably lower emplacement pressures than Nb-Ta-poor granites. Nb-Ta-rich granites also have higher fluoride contents, strong fractionation into twin pairs such as Zr-Hf, Y-Ho and Nb-Ta, and an abundant, probably exsolved, fluid phase, which is not or not as evident in Nb-Ta-poor granites, probably in part because the Nb-Ta-rich granites reach their solidus later (about 550 ºC). The geochemical signature of the Iberian rare metal granites follows the trends of mainly two-mica granites and P-rich cordierite granites, but also of granodiorites and even type I granites, suggesting that the rare metal granites may have different parental magmas. Thermodynamic modeling shows that many of the geochemical characteristics of the RMGs can be explained by a process of extreme differentiation, while others cannot, e.g. Na evolution. In terms of ore deposition, white mica plays a very important role in explaining the variation of the Ta/Nb ratio, although the latter could also be controlled by late Nb-Ta oxides crystallization and even by acidic fluids that remove Nb relative to Ta from earlier Nb-Ta oxides.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

In this paper, mineralogical and elemental geochemical characteristics of massive sulfide samples collected from Jade hydrothermal field, located in the Izena depression in the central graben of Okinawa Trough, were analyzed by means of optical microscopy, scanning electron microscopy and electron probe. The results show that the sulfide in Jade hydrothermal area can be divided into Zn-Cu-Pb rich massive sulfide and Zn-Fe rich massive sulfide. The former is composed of sphalerite, galena, anglesite, chalcopyrite and pyrite, and its formation stage can be divided into pyrite stage, sphalerite-chalcopyrite stage, anglesite stage and colloidal pyrite stage. The latter is mainly composed of sphalerite, pyrite, marcasite and a small amount of galena, which can be divided into galena stage, pyrite stage, sphalerite stage, pyrite and marcasite stage. Cu and Zn in pyrite may exist in the form of microinclusions, while Ag and Pb may exist in pyrite in the form of fine galena inclusions containing Ag. Fe and Cu may enter sphalerite in the form of ion replacement. Zn may enter chalcopyrite in the form of ion replacement, and As and Pb may be inclusions in chalcopyrite as As-bearing galena inclusions. Consistent with the previous understanding, the metal elements in the hydrothermal liquid system in Jade hydrothermal field mostly migrate with the hydrothermal fluid as sulfur complexes, and when the hydrothermal fluid mixes with seawater, the physical and chemical conditions of the fluid change, resulting in sulfide mineral precipitation. However, the chemical structure of chalcopyrite is still controversial, which restricts the understanding of the substitution mechanism of trace elements during chalcopyrite precipitation.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

The inherited ‘EIA’ process at Brexit is based on a ‘Project’ period from Inception tothe start of construction works. The ‘Incompleteness’ of the process covers andidentifies stages that will impact on the environmental cycle: construction period,operational life, de-commissioning and a return to acceptable environmental footprint.A master environment structure-plan framework is required to commence with theupgrading of the complete ‘EIA’ process, embracing separate limbs for the UK’spriority environmental targets for climate change, and other major adverse effectswhich result in serious ‘harm’ to the UK environment. The identification of the processfor ‘incompleteness’ requires effective sustainability, and inclusion of effectivemanagement tools, for the essential ‘monitoring/control/recording’ proceduresthroughout the project life and the natural environmental cycle. This will allow theopportunity for a new approach to a structured ‘Suite of EIAR Directives’, to enable a‘EIAR’ regime that ‘will remain fit and proper for UK purpose’.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

This article reevaluates the Woesean concept of crossing a ‘Darwinian threshold’ from pre-genomic communality, as prevailing in an ancestral ‘progenote’ state, to vertically stable lineages of autonomous and self-similar cells. This transition from collective trunk-line evolution to Darwinian speciation is dependent on the generation of modular organismal genomes. The same general principle should be valid at subcellular levels, allowing the emergence of semi-autonomous genomic agents, such as viruses and plasmid-carrying endogenous vesicles with organelle-like properties. As compartmentalized agents of endogenous nature could start with smaller genomes than those required for fully autonomous cells, it is conjectured that stable subcellular lineages emerged earlier than their cellular counterparts. Referring to the recent ‘pre-endosymbiont hypothesis’, it is proposed that free-living bacteria (the first ‘prokaryote’ cells) arose by ‘lineage escape’ from plasmid-bearing organelle-like compartments, evolving inside the internally complexifying ‘paracells’ of the progenote community. The double-membrane envelopes of diderm bacteria may have resulted from cell-biological processes facilitating cellular lineage escape. The later emergence of archaeal cells (resembling bacteria in ‘prokaryote’ appearance with unichromosomal genomes) and eukaryotic organisms (with compartmented cells and multichromosal genomes) can also be interpreted in terms of this modified progenote hypothesis. Conceivably, the multichromosomal genomes of eukaryotes were bundled in endogenous nuclear compartments to organize a ‘nuclear-cytoplasmic lineage’, which became vertically stable by perfecting mitosis/meiosis-like divisions and yet retained some intra-species population confluence by sexual division-fusion cycles.

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

The efficacy of predicting geochemical parameters with a 2-chain workflow using spectral data as the initial input is evaluated. Spectral measurements spanning the approximate 400-25000nm spectral range are used to train a workflow consisting of a non-negative matrix function (NMF) step, for data reduction, and a random forest regression (RFR) to predict 8 geochemical parameters. Approximately 175000 spectra with their corresponding chemical analysis were available for training, testing and validation purposes. The samples and their spectral and chemical parameters represent 9399 drillcore. Of those, approximately 20000 spectra and their accompanying analysis were used for training and 5000 for model validation. The remaining pairwise data (150000 samples) were used for testing of the method. The data are distributed over 2 large spatial extents (980 km2 and 3025 km2 respectively) and allowed the proposed method to be tested against samples that are spatially distant from the initial training points. Global R2 scores and wt.% RMSE on the 150000 validation samples are Fe(0.95/3.01), SiO2(0.96/3.77), Al2O3(0.92/1.27), TiO(0.68/0.13), CaO(0.89/0.41), MgO(0.87/0.35), K2O(0.65/0.21) and LOI(0.90/1.14), given as Parameter(R2/RMSE), and demonstrate that the proposed method is capable of predicting the 8 parameters and is stable enough, in the environment tested, to extend beyond the training sets initial spatial location.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

Chemical plants are characterized by the management and operation of various hazardous materials; thus, accident risk is inherently high. Nevertheless, the incidence of chemical accidents in Korea has effectively stabilized, with no marked increase attributable to the implementation of systematic safety management procedures based on process safety management system principles. In June 2023, the Ministry of Employment and Labor in Korea unveiled the Serious Injury and Fatality (SIF) report, meticulously cataloging 4,432 instances of grave accidents spanning six years (2016–2021). The compilation comprises 1,834 and 2,574 cases within the manufacturing and affiliated sectors and the construction sector, respectively. This study provides an overview of each accident, and elucidates the causes, and recommends preventative strategies. The objective was to galvanize companies across various industrial landscapes and fortify their intrinsic safety management protocols by using accident data delineated per sector. Sixteen specific accident cases from the SIF report, all of which occurred in facilities regulated by process safety management (PSM), were investigated. Technical analysis was conducted, focusing on explosion accidents within the organic catalyst packaging process, notable for their unique patterns of occurrence. This analysis extended to an examination of the reproducibility of such accidents. Employing two system analysis methodologies, system theoretic accident model and process and barrier-based systemic cause analysis technique, this study provides insights into the causative factors of the accidents and formulates comprehensive strategies for the prevention of future accidents. The findings will contribute significantly to reducing the risk of accidents within the catalyst packaging domain and assist in the development of robust recurrence prevention measures.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the analysis as well as theoretical considerations concerning to design of gear size ranges. This analysis consists in decomposition of the designed artefact (a gear) according to the rule “from general to details view”. The basics of the object-oriented analysis were formulated. Furthermore, design phases and the objects related to theses phases were discussed. The following models have been considered: hierarchical model, entity-relationship model, data-flow model and object model. Analysis is additionally connected with interactions between particular design phases.

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

For a long time, a company's Product Development Process (PDP) was seen as supporting the operations department, although PDP decisions and mistakes have a considerable impact on market performance. This is critical even in agriculture where bad habits and practices in the PDP can lead rural producers to great losses. Therefore, this research investigated the effect on the market performance of rural products (banana) in the southern region of Brazil, based on two analyses: (i) how sustainability practices support the PDP phases and (ii) how the phases of the Product Life Cycle Assessment (LCA) mediate sustainability practices and PDP phases. This study presents a quantitative analysis using Confirmatory Factor Analysis (CFA) and hierarchical ordinary least squares (OLS) regression of data obtained from a survey of 110 rural producers who directly participate in the banana production and planning process in southern Brazil. Our results shows that sustainability practices support the PDP, and we confirm that the product development and post-development phase has an effect on market performance. In addition, we identified that in the pre-development phase of the PDP, dealing with rural products (bananas), the maturity stage of the LCA mediates sustainability. In the PDP development phase, we concluded that rural families that develop economic and environmental practices with their products in the market growth phase may have reduced results. As for the post-development phase of the PDP, we conclude that when companies invest in environmental and social practices, there is a complete mediation of the effect, where these practices lose strength if the product is in the introduction and maturity phases in the market. As originality, our study contributed to demonstrate value on the product life cycle for the product development process in agriculture using sustainability practices through a systemic approach, filling the gap in the literature due to the lack of research on these areas seen in an integrated way.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

Detailed description of carbonate minerals different in magnesium content of Triassic dolomites were presented in this article. The tests were carried out to determine geochemical and miner-alogical features in the terms of their geoengineering properties. The following carbonate phas-es were identified: a low-Mg calcite, a high-Mg calcite, a proto-dolomite, an ordered dolomite and a huntite. The following research methods were used: microscopic analysis, X-Ray Diffrac-tion, X-Ray Fluorescence and Electron probe microanalysis. The samples were collected from the Tarnowice formation which is the lower part the profile of the Upper Muschelkalk. On the basis of the results the chemical formulas of carbonate phases were calculated. The ranges of Mg and Ca content were presented in formulas. The results indicate of Mg in low-Mg calcite ranges from 0.6 to 1.2%, in high-Mg calcite from 7.47 to 10.41%. In proto-dolomite it ranges from 10.96 to 11.78%. In ordered dolomite Mg content is stoichiometric value for dolomite – 13.18%. Due to the reduced Mg content in identified huntite (the value ranges from 13.62% to 17.76), this carbonate phase was named as de-huntite.

Nowadays, rotor-stator mixers are widely used in the chemical process industry to carry out the dispersion and de-agglomeration processes for manufacturing the homogenous electrode slurries. Development of the process simulation models for the turbulent mixing of these slurries helps to optimize the mixing parameters such as rotational speed and dispersion time. In this work, computational fluid dynamics (CFD) approach through ANSYS Fluent are explored to determine and analyze the flow patterns, velocity fields and viscosity distribution during the dispersion of anode slurries. It utilizes a non-homogeneous Eulerian multiphase approach and the typical k-ε model to create turbulence fields and compute the mixing rate. This work significantly improves our understanding of the relationship between rotor speed, dispersion time, viscosity distribution, and mixer geometry in rotor-stator mixers.

The microstructure of the substrate plays a crucial role in the anodizing process. Anodizing cast aluminum alloys is quite challenging due to the higher levels of alloying elements present compared to pure aluminum. Elements such as silicon, iron, and copper significantly impact the growth and quality of the anodic layer. Additionally, anodizing parameters such as electrolyte composition, current density, and temperature are critical in determining the morphology and thickness of the anodic film. The casting process, surface condition, and post-treatment also affect the properties of the anodic layer. Optimizing these parameters is essential to achieve a durable and high-quality anodic layer. This work aims to provide a comprehensive understanding of the various factors affecting the anodizing of cast aluminum alloys and the properties of the anodic layer, including its thickness, corrosion resistance, and wear resistance.

This study examines the potential of implementing a systematic approach to piloting desalination plants, with the objective of evaluating energy improvements in water desalination processes. The global scarcity of freshwater resources has significantly influenced the development of desalination technologies, with reverse osmosis emerging as one of the most prevalent and highly regarded methods. Pilot tests with the latest generation of reverse osmosis membranes in large desalination plants are becoming increasingly common. This is due to the fact that small-scale experiments are being carried out on the operation of new generation membranes with better salt rejection and lower energy consumption. The objective of this approach is to achieve the optimal water quality standard at the lowest possible cost. In this manner, pilot tests are being conducted prior to the determination of whether to alter the reverse osmosis membranes, as this represents a substantial investment. The objective of these tests is to minimise the risk of making an erroneous decision and to ensure optimal results in terms of energy consumption, operating costs and reduction of environmental impact, while complying with the requisite water quality standards. In this case, the Pareto analysis is employed to identify the two or three most significant causes whose treatment affects more than 80% of the potential energy savings to be implemented. This article introduces a novel approach to studying a total of 180 desalination plants at the territorial level in the Canaries.

Extraction techniques of important bioactive molecules from the major concern of Seafood byproducts are getting emphasis for better valorization. Employing green extraction technologies for efficient and quality production of these bioactive molecules is also strictly required. Hence, understanding the extraction process parameters to effectively design an applicable optimization strategy could make this real. In this review, statistical optimization strategies applied for the extraction process parameters of bioactive molecules from Seafood byproducts are focused. The type of experimental designs, and techniques applied to criticize and validate the effects of independent variables on the extraction output was addressed. Dominant parameters studied were enzyme/substrate ratio, pH, time, temperature and power of extraction instruments. The yield of bioactive compounds, chitin and chitosan, proteins and peptides, enzymes and carotenoids (Astaxanthins) were the most studied responses. Efficiency and/or economic and quality considerations and their selected optimization strategies that favour the production of potential bioactive molecules were also reviewed.

Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

Plato defined a quality as “some degree of perfection” [49]. Studies on quality have unveiled the internal and external quality factors [17] that significantly impact product quality [4]. Internal factors are invisible to the end customer and are dependent on overall work organisation by the development team [17]. This work organisation is called “the process” [11],[33]. In this article, we will discuss how to address the drone-dedicated software development process to support system verification and ensure product quality by supporting quality characteristics and therefore increase software development awareness and control. We will discuss the process's influence on overall work activities and relationships between those activities by addressing the software development process utilised in the drone-dedicated GNSS-denied navigation system development project. The result was observable after three weeks of starting the software development. It was focused on better team awareness, faster task completion, lower number of development mistakes, and better and faster change response than we observed in other projects that didn’t follow the predefined process.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This research investigates the environmental characteristics of the saline lake in the Jiangling depression, southwestern Jianghan Basin from Paleocene to Eocene using bulk-rock geochemistry. The ratios of FeO/MnO, Al2O3/MgO and C-value indicate a semi-humid to semi-arid climate in the early-middle Paleocene. There was a rapid shift to a humid climate during the late Paleocene to early Eocene, following a short-time intense dryness. The Eocene climate was arid, but experienced intermittent humidity. The variation trend of CIA, CIW and PIA is similar to that of FeO/MnO, Al2O3/MgO and C-value, so the chemical weathering was influenced by climate changes. The redox conditions of lake in the Jiangling depression during Paleocene to Eocene were reconstructed using the ratios of U/Th, Ni/Co, and V/Cr. In the humidity and alternations of aridity and humidity, the lake water received external water input, resulting in weak stratification, so the sediments were in oxidation condition. In the aridity, lakes become a still water environments, leading to sediments formed in reduced condition. The salinity of the lake in Jiangling depression from Paleocene to Eocene was determined through the analysis of sedimentary sequences and the change of Sr/Ba ratio. In the early-middle Paleocene, the salinity of lake varied greatly. From the late Paleocene to the early Eocene, the salinity of lake decreased. In the Eocene, the salinity of the lake increased, and the halite precipitated, and finally the salinity of the lake decreased due to humid climate.

Variations in geochemical signatures of fossil brachiopod shells may be due to diagenesis and/or biological processes (i.e. ‘vital effects’). Characterize them is crucial to identify reliable areas into the shell suitable to paleoclimatological studies. This investigation contributes to an in-depth understanding of geochemical variations of Gigantoproductus sp. shells (SW Spain, Serpukhovian age), which could affect to the Late Paleozoic Ice Age interpretation. Microstructural, crystallographic, cathodoluminescence and geochemical (minor and trace elements, δ18O, δ13C, and strontium isotopes) characterisation have been performed on the tertiary layer of the ventral valve, to assess the preservation state. Poorly-preserved areas exhibit microstructural and geochemical changes such as recrystallisation, fracturing and higher Mn and Fe enrichment. Moreover, these areas have higher dispersion of ⁸⁶Sr, ⁸⁷Sr, δ18O and δ13C than well-preserved areas. Three structural regions have been identified in well-preserved areas of ventral valve by differences in valve curvature and thickness, such as the umbonal, thick and thin regions. These regions have different proportions of Mg, S, Na, δ18O, and δ13C, whom are interpreted as ‘vital effects’ and probably are related with growth rate differences during shell growth. Gigantoproductus tertiary layer seems the best suitable to paleoclimatological studies because it retains the original microstructure and geochemistry.

Sehezar area is located in southern Tonokabon in Mazandaran province, north of Iran, near the Tarom – Hashdtjin belt. The existence of granitoid masses in the region can be important in terms of the potential of mineralization. Geochemical anomaly separation from the background is one of the important steps in mineral exploration. In the past decades, geochemical anomalies have been identified by means of various methods. Some of these separation methods include: statistical analysis methods (like univariate, bivariate, multivariate statistics), spatial statistical methods and fractal and multi-fractal methods. To identify the anomalous area, 71 stream sediment samples were collected from the area and analyzed by the ICP-MS method, and then interpreted. Initially, data were normalized and afterwards, univariate analysis (threshold limit and screening (P.N) methods) was used, in which results of the probable and definite anomaly of the threshold method were confirmed by the P.N screening method. Finally, the maps of the anomal zones were drawn. Then, bivariate analysis (Pearson correlation coefficients) and multivariate analysis on normal data were performed on SPSS software, in which factor analysis and cluster analysis were used for multivariate analysis. As a result of using the factor analysis method, six factors were identified and factor maps were drawn by the Surfer software. Also, by using cluster analysis, the variables were divided into two groups. In order for a better separation of the geochemical anomaly from the background, in addition to the threshold method, the Concentration - Area fractal method was used. Here, the fractal geometry using full-logarithmic graphs of the Concentration - Area obtained is capable of separating the stairs of different sections (background, threshold, and anomaly) with respect to the angle coefficient of the Concentration - Area plot. Then, in conclusion, results of these methods were compared and investigated, and finally, the anomalies area maps of the Au, Ag, Cu, Fe, W elements were drawn by Concentration - Area fractal and threshold methods and anomalous zones were introduced.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

Exploration geochemistry is an essential method for discover new mineral areas. However, with the increase of exploration degree, relying solely on "strong, broad and multiple" anomalies to guide exploration work has become increasingly challenging. How to effectively identify valuable geochemical information remains a hot and frontier topic in the field. Thus we proposed a geological connotation method (GCM) that provides an objective geological connotation to big geochemical data based on regional geological and geochemical characteristics of known typical deposits. There are mainly two types of geochemical anomalies expression: (1) the metallogenic intensity anomaly map (MIAM) obtained by accumulating specific anomalous elements, which directly reflects the degree of material exchange and superposition modification during mineralization; (2) the metallogenic type anomaly map (MTAM) obtained by accumulating the mineralization concentration coefficients of elements related to a certain genetic type, which can highlight the anomalies caused by a specific genetic type of deposit. These have been tried and applied in the exploration of the Gangdese, North Himalayas, Nyenchen Tanglha and other metallogenic belts in Tibet, and have made a series of breakthroughs in mineral resources exploration represented by Qulong, Zhunuo and Zhaxikang. The advantage of GCM is that it not only solves the problem of missing ore in the verification of "strong, broad and multiple" anomalies, but also can quickly and preferably delineate the strongest mineralized areas, and better overcome the influence of numerous factors on the anomalies, such as the chemical nature of elements, redox environment, geomorphic landscape and weathering and stripping, so that the anomaly evaluation becomes simple, objective and highlights the regularity.

This research evaluates the mineral ions and their concentrations in formation water from five well samples of the Bibi Hakimeh oil field. The study reveals the presence of calcium (Ca2+), so-dium (Na+), and magnesium (Mg2+) cations, as well as sulfate (SO42-), bicarbonate (HCO3-), and chloride (Cl-) anions, which are soluble in water within the Bibi Hakimeh oil formation. Fur-thermore, mineral deposits of CaSO4, CaSO4.2H2O, CaCO3, and MgCO3 are investigated. The findings highlight the significant formation of calcium sulfate and calcium carbonate mineral deposits under the operating conditions of the Bibi Hakimeh oil well. Additionally, the study examines the interaction between rock and water of the Bibi Hakimeh formation, revealing a notable correlation between the concentration of calcium and magnesium ions and the water-rock reaction in this field

Introduction: Treating elbow fracture-dislocation is a challenge, especially in the situation of basal-coronoid trans-ulnar fracture. The study ams to explain whether or not the minimal invasive surgery (MIS) would be feasible in elbow dislocation with coronoid fracture. Materials & Methods: At Taipei Veterans General Hospital, patients who had elbow dislocations with coronoid process fractures underwent single one surgeon’s MIS techniques which included the fluoroscopy-guided ulnar anteromedial (FGUAM) approach in the stage of reducing coronoid process. When there is a proximal ulnar fracture, the posterior incision should be necessary, followed by the incision over the lateral or medial elbow in treating radial fractures or ligament injuries. Results: The Flow Diagram about approach recommendation was established in base of defining MIS as not to do cross-plane dissection. Anteriorly rigid fixation for the coronoid process was also emphasized. Conclusions: MIS can be achieved by multiple limited surgical incisions. However, if there is an unstable ulnar metaphysis or ligament avulsion fracture, the posterior approach has to be extended and the so-called MIS fails to be established.

Ca-bentonite (CB) alone and in a mixture with limestone (L), tobacco biochar (TB) and zeolite (Z) on the fixation, geochemical fractions and absorption of Cd and Zn by Chinese cabbage in smelter heavily polluted (S-HP) and smelter low polluted (S-LP) soils were investigated. The results showed that the CB+TB and CB+L+TB treatments significantly immobilized Cd up to 22.03% and 29.68%, respectively, and reduced uptake by Chinese cabbage shoot to 35.98% with CB+Z+L and 61.35% with CB+L in S-HP and S-LP soils compared with the control. The CB+ Z+ L+TB treatment mobilized Cd up to 4.45% and increased absorption in the shoot by 9.85% in S-HP soil. The greatest immobilization of Zn was 53.18% and 58.20% with the CB+Z+L+TB treatment, which reduced Zn uptake in the plant shoot by 9.94% with CB + L and 58.04 with CB+Z+L+TB in S-HP and S-LP soils. The CB+Z+TB and CB+TB treatments mobilized Zn up to 35.40% and 4.80%, respectively, in both soils. Furthermore, the uptake of Zn in plant shoot was observed by 58.96% and 7.82% with application of CB+Z and CB+TB treatments, respectively, in S-HP and S-LP soils. Overall, our results suggest that Ca-bentonite alone and in mixtures with different amendments can be used to reduce the phyto-extraction of Cd and Zn in Zn-smelter polluted soils.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

The article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that was not previously studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are: pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies have established the presence of gold grains in free form, ranging in size from 0.9-10.2 mkm Au-ultrafine and fine gold. Obtaining a gold-containg concentrate with a gold content of 15.95 g / t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class -0.05 mm, additional grinding of hydrocyclone sands to a fineness of 90.0-95.0% of the class finer than 0.050 mm, and control centrifugal separation. Since pyrite in technogenic raw materials is the main gold-containing mineral, this paper presents studies on the oxidizability of pyrite with the TCCA oxidizer. The results of studies on the oxidation of pyrite using the TCCA oxidizer show that the products of its hydrolysis oxidize pyrite with the formation of various iron compounds on its surface. Pretreatment of gold-containing concentrate with oxidizer TCCA for 3 hours before the cyanidation process (20 hours) allows to increase the recovery of gold in the solution by 5.8 %.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

In this paper, the boiling flow inside a nanochannel with 700000 argon particle has been simulated by molecular dynamics (MD) simulation. This approach has been employed to analysis the superheated flow and its heat transfer pattern as well. For all simulations an external thrust force varying from 1 PN to 12 PN is exerted on inlet nanoparticles along the channel to have the forced annular boiling flow. Computations reveal that saturation condition and superheat degree have significant impacts on the liquid-vapor interface. Furthermore, because of the major influence of surface tension throughout a nanochannel, the x-velocity of liquid film and vapor core has not considerable fluctuations and stay smooth. All provided results show the behaviors completely similar to the available outcomes in the literature.

Listwaenite rocks are widely spread in Fenja area of the Semail ophiolite of Oman and in Islam Abad area of the Neyriz ophiolite of Iran. There are three types of listwaenites found in these regions: silica-, carbonate-, and carbonate-silica (which includes dolomite, calcite, and magnesite. The alteration of host harzburgites started with hydrothermal alteration to serpentinite, followed by carbonation and silicification of serpentinite. Calcite- and magnesite-dolomite- listwaenites are more abundant in the Fenja area of Oman, while dolomite-listwaenites are more abundant in Islam Abad area in Iran. The mineralogy of listwaenites varies in both Iran and Oman; common minerals include quartz, calcite, goethite, magnesite, dolomite, serpentine, hematite, magnetite, Cr-mica, and Cr-spinel The major element chemistry of the different types of listwaenites in both Fenja and Islam Abad area generally comparable, and is largely similar to that of hydrothermally carbonated harzburgites, serpentinite, and listwaenites worldwide, despite spanning extraordinary and highly variable contents in major oxides, such as CaO, SiO2, MgO and LOI. Relict texture and common occurrence of Cr-spinel as well as the high concentrations of Cr, Ni and Co suggest that the protolith of the listwaenites in both regions was serpentinized harzburgites and serpentines. In comparison to the primary mantle and chondrite in spider diagrams, the Neyriz listwaenites have higher trace and REE element abundances than comparable listwaenites in the Fenja region. Harzburgite-normalized patterns of trace elements and REE in serpentinite and listwaenites overlap the average composition of harzburgite. PM-normalized trace element and REE patterns for serpentinized harzburgite and serpentinite show enrichment in Cs, U, Pb and Sr, with no Eu anomaly, comparable to mantle wedge serpentinites. The variable and high abundances of Ca, Mg, Ba, Zr, Sr, Pb, Zn, Mo and W in the carbonate- and silica-carbonate listwaenites, with unique Si enrichment and Mg, Na2O, Zr, Y, Ba, Sr, Rb, Cu, Pb, Sc, Cs, Nb, Mo and W. depletion in silica listwaenites are indicative of large fluctuations in major and trace element mobility. Cr, Ni and Co were immobile during alteration Enrichment in Ca and Si could occur by internal or late outside supply. Ca, Mg and Si are conceivably the foremost mobile major components amid harzburgite and serpentinite carbonation with mobilization confirmed by formation of quartz and Mg-carbonate in silica-carbonate listwaenites and quartz in silica listwaenites. The listwaenites in Islam Abad and Fenja area were formed due to hydrothermal alteration of serpentinite along thrust faults and shear zones which acted as pathway for Ca and/or Si rich fluids. The intensity of deformation in Islamabad listwaenites has been higher than Fenja listwaenites as indicated by higher abundance of trace elements.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

While there are software tools available for assisting to conduct the Life Cycle Assessment (LCA), such as OpenLCA, these tools lack integration with process design, simulation and optimization software. As LCA has critical role in sustainable product design, it is presented in this work a platform called EMSO_OLCA, which integrates the LCA provided by OpenLCA into the Environment for Modeling, Simulation, and Optimization (EMSO). EMSO_OLCA incorporates a database of environmental impact assessment methodologies from OpenLCA and aligns to the principles of LCA outlined in ISO 14040 and ISO 14044. Validation tests were conducted to compare the results obtained by the LCA of sugarcane ethanol using OpenLCA and EMSO_OLCA, revealing a high level of agreement. The average relative error was 0.045%, indicating a negligible discrepancy between the tools. Besides, it took only 0.3 seconds for calculation, which is desirable for using with process systems engineering tools. A second case study was applied to a steam and bioelectricity production from the combustion of sugarcane bagasse and straw in a combined heat and power system. The results show the integration of LCA with simulation and sensitivity analysis tools, thus contributing for supporting sustainable decision-making processes. EMSO_OLCA bridges the gap between LCA and process engineering, enabling a holistic approach to sustainability, design and implementation of environmentally friendly solutions.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

In this study, a cholera infection model with the bilinear infection rate is developed by considering the perturbation of the infection rate by the mean-reverting process. First of all, we give the existence of a globally unique positive solution for a stochastic system at arbitrary initial value. On this basis, the sufficient condition for the model to have an ergodic stationary distribution is given by constructing proper Lyapunov functions and tight sets. This indicates in a biological sense the long-term persistence of cholera infection. Furthermore, after transforming the stochastic model to an relevant linearised system, an accurate expression for the probability density function of the stochastic model around a quasi-endemic equilibrium is derived. Subsequently, the sufficient condition to make the disease extinct is also derived. Eventually, the theoretical findings are shown by numerical simulations. Numerical simulations show that the impact of regression speed and fluctuation intensity on stochastic systems.

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

Lessons learned and risk-based outcomes from modernising the Australian Standard for post-mortem inspection and disposition judgement of beef, sheep, goat and pig carcases are described. Initial Risk Profiles identified priorities for quantitative assessments. The main difficulty encountered was the paucity of quantified performance of current inspection. Resolving this involved acquiring gross abnormality data representing regional production/proportional abattoir volumes, the range of gross abnormalities appearing nationally, proportional occurrence at carcase sites, and seasonality to enable comparisons. Evidence and discussion are provided for associated challenges experienced including preventing contamination, use of food chain information to support amendment, inspection as a part of industry Quality Assurance and opportunities to improve inspector training. Criteria considered by the Competent Authority for determination of equivalence of alternative post-mortem inspection techniques included comparisons of public health risk, non-detection rates for gross abnormalities, and microbial contamination resulting from inspection activities, as appropriate. Most gross abnormalities detected arose from animal health and welfare conditions affecting wholesomeness and did not present as food safety hazards. Non-detection rates between current and alternative inspection (observation) were negligible. A Quantitative Risk Assessment for Cysticercus bovis was conducted. Carcases with multiple gross abnormalities predominantly reflected historic infections (prior septicaemia) where trimming achieved wholesomeness unless cachexic.

The textile sector is responsible for a number of environmental impacts. Due to the in-creasing quantities of textiles, their share is rising and a trend reversal from a linear to a circular textile chain is needed. This article presents the background, methodological approach and results of a participatory textile development model. In the commercial B2B sector, three textile prototypes were developed together with users and trialled over several months in three application areas. Textile development took into account the requirements of fibre regeneration in the product design and focused on innova-tive chemical recycling solutions. The three sustainably aligned textiles were subject-ed to spectroscopic and textile-technological tests. Screening life cycle assessments an-alysed their environmental profile and compared it with reference textiles that are used as standard. Overall, it is clear that the three textiles can match conventional ref-erence textiles in terms of quality and have considerable environmental benefits com-pared to the reference textiles. The user survey did identify concerns about a high arti-ficial fibre content, although a general rejection of recycled fibres was not observed. The results show that a transformation is possible, but must start with the fibre com-position; recycling, on the other hand, is of minor importance.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

The main focus of the in vitro toxicity assessment methods is on the viability of the cells, which is usually based on metabolism changes. Yet, when exposed to toxic substances, the cell triggers multiple signals in response. With this in mind, we have developed a promising cell-based toxicity method that observes various cell responses when exposed to toxic substances (either death, division or remaining viable). Based on the collective cell response, we observed and predicted the dynamics of the cell population to determine the toxicity of the toxicant. The method was tested with two different conformations: In the first conformation, we exposed a monoculture model of blood macrophages to UV light, hydrogen peroxide, nutrient deprivation, tetrabromobisphenol A, fatty acids and 5-fluorouracil. In the second, we exposed a coculture liver model consisting of hepatocytes, hepatic stellate cells, Kupffer cells and liver sinusoidal endothelial cells to rifampicin, ibuprofen and 5-fluorouracil. The method showed good accuracy compared to established toxicity assessment methods. In addition, this approach provided more representative information on the toxic effects of the compounds as it considers the different cellular responses induced by toxic agents.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

Wild-grown edible mushrooms are important in world diet, which are also efficient metal accumulators. Yunnan, southwest China is the main producing region with typically high geochemical metals. Environmental factors, bioaccumulation, distribution and human health risk of metals were examined in paired soil and Tricholoma matsutake (n=54). T. matsutake grows on acidified soils (pH=3.95–6.56) and metals showed strong heterogeneity with Fe, Mn, Zn and Cu ranged at 16–201, 0.046–8.58 g kg–1 and 22.6–215, 3.7–155 mg kg–1. High soil Fe content led to its great accumulation in T. matsutake (0.24–18.8 g kg–1). However, though soil Mn content was great higher than Zn and Cu, their concentrations in T. matsutake were comparable (21.1–487 vs. 38.7–329 and 24.9–217 mg kg–1). This suggested that T. matsutake prefers to accumulate Zn and Cu than Mn, and supported by bioaccumulation factor (BAF=0.32–17.1 vs. 0.006–1.69). Fe was mainly stored in stipe, while Mn, Zn and Cu were in cap, with translocation factor (TF) was 0.58 vs. 1.28–1.94. Therefore, stipe Fe showed the highest health risk index (HRI) at 1.28–26.9, followed by cap Cu (1.01–2.33), while 98–100% of Mn and Zn were risk-free. The higher concentration and greater risk of Fe was attributed to the significant effect of soil Fe content (R=0.34) and soil pH (R=–0.57). This study suggested that Fe as an essential mineral may exert toxic effects via T. matsutake consumption from geochemical high background areas.

Forest vegetation plays a key role in the cycling of mercury (Hg) and organic matter (OM) in terrestrial ecosystems. Litterfall has been indicated as the major transport vector of atmospheric Hg to forest soils, which is eventually transported and stored in the sediments of forest lakes. Hence, it is important to understand how changes in forest vegetation affect Hg in soil and its biogeochemical cycling in lake systems. We investigated the pollen records and the geochemical compositions of sediments from two lakes (Schurmsee and Glaswaldsee) in the Black Forest (Germany) to evaluate whether long-term shifts in forest vegetation induced by climate or land use influenced Hg accumulation in the lakes. We were particularly interested to determine whether coniferous forests were associated with a larger export of Hg to aquatic systems than deciduous forests. Principal components analysis followed by principal component regression enabled us to describe the evolution of the weight of the latent processes determining the accumulation of Hg over time. Our results emphasize that the in-lake uptake of Hg during warm climate periods, soil erosion after deforestation and emissions from mining and other human activities triggered changes in Hg accumulation during the Holocene stronger than the changes caused by forest vegetation alone.

In this study, a critical review was carried out using the Web of ScienceTM Core Collection database to analyse the scientific literature published to date to identify lines of research and future perspectives on the presence of chemical pollutants in beer brewing. Beer is one of the world's most popular drinks and the most consumed alcoholic beverage. However, a widespread challenge with potential implications for human and animal health is the presence of physical, chemical and/or microbiological contaminants in beer. Biogenic amines, heavy metals, mycotoxins, nitrosamines, pesticides, acrylamide, phthalates, bisphenols, microplastics and, to a lesser extent, hydrocarbons (aliphatic chlorinated and polycyclic aromatic), carbonyls, furan-derivatives, polychlorinated biphenyls and trihalomethanes are the main chemical pollutants found during the beer brewing process. Pollution sources include raw materials, technological process steps, the brewery environment and packaging materials. Different chemical pollutants have been found during the beer brewing process, from barley to beer. Brewing steps such as steeping, kilning, mashing, boiling, fermentation and clarification are critical in reducing the levels of many of these pollutants. As a result, their residual levels are usually below the maximum levels allowed by international regulations.

The Konya Closed Basin (Quaternary, Central Turkey) is a graben basin which expands toward the east-west and it is controlled by faults on three sides: The Konya fault zone in the west, the Divanlar fault zone in the east and the Karaömerler fault zone in the north. Calcretes developed in relation to fault systems in the Konya region are concentrated in areas where faults cut Quaternary aged terrestrial deposits. In this study, it is aimed to elucidate the deposition conditions, geochemistry and age (with ESR method) of the calcareous deposits associated with faults in the Konya Closed Basin. Calcretes in the region existing as coatings, dust, nodules and layers are in the form of dolocrete and clayey calcrete. Dolocretes were deposited in the Quaternary terrestrial sediments on the ophiolitic rocks and geochemical data point to an ultramafic source. Bacterial community, clay, quartz minerals and calcite cement are observed in the calcretes formed in areas with limestone basement. According to the results of ICP-MS analysis of samples taken from Konya calcretes, the %MgO contents are between 0.99 and 7.7; CaO%: between 34.71 and 50.71; %SiO2 between 3.22 and 20.59. %MgO in dolocretes are between 11.65 and 21.01; %CaO between 8.44 and 29.57; %SiO2 values between 4.48 and 9.17 The δ13C and δ18O isotope values of calcretes range from -3.87 to -7.62 and from -3.62 to -7.45 respectfully. Average δ13C values indicate that calcrete formation took place under pedogenic condition or in shallow groundwater. The calcretes deposited in 3 locations around the city of Konya (on the Konya fault zone) were dated by using the Electron Spin Resonance (ESR) method and ages between 217.47 and 389.85 ky were obtained. The calcrete samples taken from the fault planes (dip-slip normal fault bordering the Upper Cretaceous Ophiolitic Mélange and the Quaternary Karahüyük Formation) gave a relative age for faulting as being 292.86 ky. This first dating study conducted in the Konya Fault Zone has provided important clues to elucidate the formation history of Konya Closed Basin (KCB) and the paleo-seismological past of Konya.

Carbon tax policies (CTP) are globally acknowledged for curbing energy consumption and emissions. Despite global adoption, China's reluctance to embrace a carbon tax, possibly due to effectiveness and public acceptance concerns, is notable. This study employs Choice-Based Conjoint Analysis to gauge Shanghai residents' preferences on four CTP attributes. Among Shanghai's populace, the annual cost of the carbon tax policy ranks highest (48.87%), followed by implementation transparency (24.72%), revenue utilization (16.68%), and policy implementers (9.73%). Notably, Shanghai residents exhibit an average annual willingness to pay of 1435.28 CNY, indicating increased acceptance. Enhanced public awareness of carbon tax policies significantly boosts willingness to pay, augmenting carbon tax revenues and fostering low-carbon technology development. Additionally, transparency improvements in carbon tax policy yield notable increases in willingness to pay, underscoring the link between understanding CTP and its perceived importance. These findings highlight the potential of carbon tax policies in advancing sustainability and transitioning to low-carbon economies.

Micellar Casein Concentrate (MCC) is manufactured from microfiltration (MF) of skim milk utilizing ceramic or polymeric membrane filtration. While ceramic filtration has higher efficiency, use of polymeric is cost effective and the process is familiar to several US dairy processors. The aim of the present study was to develop an optimized membrane filtration process to produce MCC using spiral wound polymeric membrane filtration (SW MF) system by systematic selection of transmembrane pressure (TMP) and level of diafiltration (DF). Using skim milk as feed material, preliminary lab-scale MF experiments were conducted using 0.5 µm polyvinylidene fluoride (PVDF) membrane. Three TMP (34.5, 62.1, and 103.4 kPa) and three levels of DF (70, 100, and 150%) along with a process without DF as control were used in the study. Effect of TMP and effectiveness of DF on flux rates, SP removal, casein to total protein (CN/TKN) ratio, casein to true protein (CN/TP) ratio, rejection of casein (rej CN) and SP (rej SP) were evaluated. At all TMP values used in the study, the overall flux (O Flux) increased with the level of DF. Highest O Flux of 30.77 liter per meter square per hour (LMH) was obtained with 34.5 kPa pressure and 150% DF. The impact of DF was more pronounced at lower pressures than at the higher pressures used in the study. With controlled DF, instantaneous flux was maintained within 80% of initial flux for the entire process run. For all the experiments, casein has a rejection of 0.97 to 1.0, while serum protein has the lowest rejection of 0.10 at 34.5 kPa pressure and 150% DF level. Use of 34.5 kPa and DF level of 150 % contributed to 81.45% SP removal, and casein to true protein ratio of 0.96. SP removal data from the lab-scale experiments were fitted into a mathematical model using DF and square of TMP as factors. The model predicts SP removal within 90-95% of actual SP removal got from the pilot plant experiments.

As the demand for long-distance flights continues to increase, supersonic transport (SST) has once again become a hot research topic. However, due to its uniqueness, there was few corresponding evaluation methods to compare the supersonic civil aircraft with common subsonic aircraft. This paper proposed an evaluation method for the competitiveness of supersonic civil aircraft based on the Analytic Hierarchy Process (AHP). Key indicators were selected to form a competitiveness evaluation model from the perspective of four criterion factors of economy, comfort, adaptability, and environment. The evaluation method proposed in this paper could reflect characteristics of supersonic civil aircraft and other subsonic aircraft, and effectively compare their competitiveness. This work can be used to evaluate the social acceptance of supersonic civil aircraft and provide reliable decision-making support for airlines' design work.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

This study introduces an integrated method for managing process risks in a Business Process Reengineering (BPR) project, using Robust Data Envelopment Analysis (RDEA) and machine learning (ML). The goal is to prioritize risks based on three standard factors of PFMEA: Severity, Occurrence, and Detection (S-O-D), and incorporating two additional factors (Breakdown Cost and Breakdown Duration) seen as undesirable outputs. The model also accounts for the effect of uncertainty on expert-estimated values by applying disturbance percentages in the linear PFMEA-RDEA model. A machine learning model is proposed to predict new values if partial or total modifications have been made to the processes. The approach was implemented in an au-tomotive sector company, and the results showed the impact of uncertainty on values by com-paring different approaches such as RPN, PFMEA-DEA, and PFMEA-RDEA. A new reduced risk categorization was achieved, who allowed for decision-makers to focus on necessary actions for reengineering.

The paper presents new data on mineralogical-geochemical peculiarities of the granites and pegmatites of the Baikal area (Olkhon Region) with implications for the age, generation conditions and geodynamic settings of magmatism. The early Paleozoic granitoids of the Olkhon region are syncollisional formations produced from the gneiss-schistose substratum of the Olkhon metamorphic sequences. Pegmatoid granites and pegmatites of the Region were generated within a wide age range (458-390 Ma) and include different mineralogical and geochemical types. Amongst the Early Paleozoic granitoids, pegmatoid rocks are products of the collisional magmatism evolution and are similar to granites in terms of the mineral composition and distribution patterns of rare and rare earth elements. On the Olkhon island (Baikal lake) the pegmatite of the Tashkiney vein belong to the Be-Nb-Ta mineralogical-geochemical type demonstrating high contents of W, Sn U, Th and very low concentrations of Li and volatile components (F, B). In the Pryolkhonye area, vein pegmatite Iliksin is with Li, Be, Nb, Ta mineralization (lepidolite, vorobyevite, samarskite et al). The studied pegmatite veins are similar both by the profound negative Ba, Sr, Eu, and Zr anomalies. The zircons from the Tashkiney vein (390±5.0 Ma) and of the Iliksin vein (430.1±2.2 Ma, U-Pb isotope LA ICP MS metod) indicate the formation of pegmatite at the late post-collisional stage of magmatism in the Olkhon Region. As regard to mineralogical and geochemical characteristics, vein pegmatites with amazonite (Ainsky and Ulan-Nur) belong to the Li-F type. The tantalum mineralization, represented by microlites and minerals of the columbite-tantalite group is associated with the Ainsky amazonite pegmatite. As opposed to the Early Paleozoic syncollisional granitoids and pegmatoid formations, the middle Paleozoic vein bodies of pegmatites (Tashkiney, Iliksin, Ainsky, Ulan-Nur) are regarded as rare-metal pegmatites. In terms of geochemical characteristics, they are similar to the rare-metal pegmatoid granites and pegmatites of the intra-plate setting widespread in Mongolia and Transbaikalia. The rare-metal mineralization in the Olkhon region may be genetically related to the evolution of Be-Nb-Ta and Li-F types of the post-collisional granites and pegmatites.

Geochemical mapping of river sands in the Manufahi area of Timor-Leste revealed potential areas for future mineral exploration. River sand samples from the study area were collected and geochemically analyzed to identify anomalous concentration distributions of several valuable elements and locate potential target areas and geological formations that may host mineral deposits. The 26 major and minor elements were identified using wavelength-dispersive X-ray fluorescence. The river sands exhibited varying elemental concentrations, with Cr, Cu, Zn, and Ba showing deviations from the normal distribution patterns. Identification of geochemical anomalies is an important task in mineral exploration geochemistry. The mean + 2 standard deviations (mean+2STD), median + 2 median absolute deviations (median+2MAD), and Tukeyâs inner fence (TIF) methods were used to determine the geochemical thresholds. This study shows that TIF and principal component analysis (PCA) methods are highly effective in calculating appropriate threshold values and identifying relevant elemental associations. These approaches have proven useful for delineating target areas for mineral deposits, resulting in reliable outcomes. Four predicted target areas with high potential for deposits and mineralization anomalies of Cr, Cu, Ni, and Ba were delineated in the study area.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&amp;E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

This paper describes the state of the art and future opportunities for process design and sustainable development. In the Introduction the main global megatrends and European Union's response to two of them, the European Green Deal, are presented. The organization of professionals in the field, their conferences and publications support the two topics. A brief analysis of the published documents in the two most popular databases shows that the environmental dimension predominates, followed by an economic one, while the social pillar of sustainable development is undervalued. The main design tools for sustainability are described. As an important practical case, the European chemical and process industries are analyzed and their achievements in sustainable development are highlighted; in particular, their strategies are presented in more detail. The conclusions cover the most urgent future development areas of the process industries, carbon capture with utilization or storage, process analysis, simulation, synthesis and optimization tools; zero waste, circular economy and resource efficiency already play an important role. However, more profound changes are needed in the coming decades, including a shift away from growth with changes in habits, lifestyles and business models. Lifelong education for sustainable development will play a very important role in the growth of democracy and happiness instead of consumerism and neoliberalism.

Asphaltene-resin-paraffin deposition (ARPD) is a complicated and prevalent issue in oil and gas industry, impacting the efficiency, integrity of petroleum extraction, production, transportation and processing systems. Considering all witnessed ARPD problems in Azerbaijan oil fields, this paper proposed a chemical method and optimized the type and the concentration of chemical inhibitors. And then the effect of selected chemical reagent on inhibiting the ARPD amount and thus en-hancing oil recovery was detected by reservoir simulation during both waterflooding and CO2 flooding production. Three new chemical compounds (namely, Chemical-A, Chemical-B and Chemical-C) were examined in laboratory conditions and their impact on rheological properties of high-paraffin oilfield samples of Azerbaijan (X, Y and Z) were investigated. Experimental results show that Chemical-C with concentration of 600 g/t has the best efficiency for alleviating the problems. After adding Chemical-C to the crude oil, the freezing point of oil is decreased from 12 °C to (-4) °C, ARPD amount is declined from 0.185 to 0.016 g and oil effective viscosity is reduced from 16.2 mPa·s to 3.1 mPa·s. It is determined that for water and CO2 flooding, higher injection pressure resulted in reduced asphaltene precipitation. Adding selected ARPD inhibitor, the oil recovery for waterflooding can increase from 52% to 62%, while it can rise from 55% to 68% for CO2 flooding.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

The literature analysis did not indicate any studies on fluorination tests of carbon nanocomposite coatings doped with transition metals of the nc-MeC/a-C type. This was the motivation for undertaking research in this area. As a model coating to investigate the effect of fluorination in a tetrafluoromethane (CF4) atmosphere, a nano-composite carbon coating doped with chromium nc-CrC/a-C produced by magnetron sputtering from graphite targets and the use of a Pulse-DC type medium frequency power supply was chosen [6]. After deposition of the gradient CrCN adhesive sublayer, fluorination of the main coating was conducted in a reactive mode in an (Ar+CF4) atmosphere at various CF4 contents. It was observed that the presence of CF4 in the atmosphere resulted in a reduced amount of chromium carbides formed in favor of chromium fluorides. So far, this is an observation that seems unnoticed by the carbon coatings researchers. Fluorine was assumed to bond much more readily to carbon than to chromium, due to the stability of tetrafluoromethane (CF4). The opposite seems to be true. The mechanical properties (nano-hardness and Young's modulus) and tribological properties in the 'pin-on-disc' friction pair are presented, along with the analysis of bonds occurring between chromium, carbon, and fluorine (XPS).

Marine water pH is becoming progressively reduced in response to atmospheric CO2 elevation. Considering that marine environments support a vast global biodiversity and provide a variety of ecosystem functions and services, monitoring of the coastal and intertidal water pH assumes obvious significance. Because current monitoring approaches using meters and loggers are typically limited in application in heterogeneous environments and are financially prohibitive, we sought to evaluate an approach to acidification biomonitoring using living gastropod shells. We investigated snail populations exposed naturally to corrosive water in Brunei (Borneo, South East Asia). We show that surface erosion features of shells are generally more sensitive to acidic water exposure than other attributes (shell mass) in a study of rocky-shore snail populations (Nerita chamaeleon) exposed to greater or lesser coastal geochemical acidification (acid sulphate soil seepage, ASS), by virtue of their spatial separation. We develop a novel digital approach to measuring the surface area of shell erosion. Surficial shell erosion of a muddy-sediment estuarine snail, Umbonium vestiarium, is shown to capture variation in acidic water exposure for the timeframe of a decade. Shell dissolution in Neripteron violaceum from an extremely acidic estuarine habitat, directly influenced by ASS inflows, was high variable among individuals. In conclusion, gastropod shell dissolution potentially provides a powerful and cost-effective tool for rapidly assessing marine pH change across a range of spatial and temporal frameworks and coastal intertidal environments. We discuss caveats when interpreting gastropod shell dissolution patterns.

DSSC devices are among the most widely studied thin-film solar cells because of their cost-effectiveness, low toxicity, and simple fabrication method. However, there is still much scope for replacing current DSSC materials due to their high cost, low volume, and lack of long-term stability. Accordingly, ITO-nanorod films were fabricated by E-beam evaporation using the glancing angle deposition method in this study. Then, the ITO-nanorod was treated by oxygen plasma via a bias-magnetron RF sputtering process to improve the efficiency of DSSC under a varying gas flow rate of 20, 40, 60, 80, and 100 sccm. The FE-SEM investigation of the ITO film structure revealed that the obtained nanorod structures have slightly different diameters. At the same time, an increase in the oxygen flow rate resulted in a rougher film surface structure. In this, the lower sheet resistance was received because of rougher morphology. When comparing the DSSC efficiency test results, we found that at a gas flow rate of 100 sccm, the highest efficiency value showed by 9.5%. On the other hand, the ITO-nanorod without plasma treatment exhibited the lowest efficiency. Hence, plasma technology can be practically applied to improve the efficiency of DSSC devices. This study will be a prototype of a highly advanced solar cell manufacturing method for the solar cell industry.