As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

To study the spatial accessibility of healthcare services in cities on the Tibetan Plateau, this paper proposes an improved 3SFCA method in the main urban area of Xining City. The improved 3SFCA method incorporates both selection weights from the Huff model and the M2SFCA approach to addressing suboptimal allocation of supply resources. Results show that the accessibility of healthcare for the main urban area of Xining City decreases in a circle to four axes, with good accessibility in the east and center but poor accessibility in the north. And there is a positive spatial relationship between population and accessibility. Besides, this paper proposes a framework for studying the spatial accessibility of healthcare on the Tibetan Plateau.

In this article, we first present and discuss eighteenth-century descriptions of minerals that contributed decisively to the development of crystallography. Remarkably, these old crystallographic descriptions included morphologies with symmetries incompatible with an internal periodic order of atoms, which, however, have been recognised to be characteristics of quasicrystals. Moreover, we also review a number of studies of minerals with aperiodic crystal structures, including recently reported natural quasicrystals of extra-terrestrial origin. Finally, we discuss the current investigations addressing the search for new quasicrystalline minerals in nature.

Gold occurrence Maljavr, located in amphibolite metamorphosed rocks in the Uragubsky greenstone belt, is the first gold prospect connected with conglomerates of Archean age, found in the Fennoscandian Shield. Gold mineralization is controlled by a series of lenses of altered rocks in biotite gneiss-metaconglomerate. The age of zircon from biotite gneiss in the zone of alteration is 2665±22 Ma, this is considered as the time of alteration processes. Biotite gneiss and altered rocks were later intruded by tourmaline granite pegmatite at 2508±7Ga, the pegmatite caused recrystallization of sulfide minerals in the altered rocks. Visible gold in association with bismuth minerals native bismuth, ehrigite (the second finding in the world), maldonite, bismuthinite, joseite-B, hedleyite was found exceptionally in polymineral inclusions in recrystallized arsenopyrite and löllingite. The age of pegmatite 2508±7Ma we regard as the time of formation of gold-bismuth mineralization. Geological position of the Maljavr occurrence, the linkage of gold mineralization with pegmatite, geochemical association Au-As-Se-Te-Bi in the mineralized rocks – all these characteristics correspond to intrusion-related gold deposits. Biotite gneiss-metaconglomerate, hosting the mineralized altered rocks, was the probable primary source of arsenic and gold for mineralization.

The orbital elactronic structure of Rare Earth Elements (REEs) contains many unpaired electrons which render them capable of storing large amount of magnetic energy in addition to being critical for hitech applications. Geological deposits are their conventional sources, and the current supply chain relies on production from these deposits. However, given their critical roles in the anticipated global energy transition, there is the need to explore other viable sources to supplement current and future supplies chains. REEs occur in coal as accessory minerals and their concentration in coal ash to levels that rival those of geological deposits has been estab;ished by sophisticated analytical chemical methods. Conmventional hydrometallurgical processes rely on acid leaching, using tioxic mineral acids. Meanwhile, organosulfonic acids have pKa values that rival those of conventional minerals acid and can, therefore, be used in hydrometallurgy but their uses in this regard are not well documented in the literature. In this extensive review, we have covered geological sources of REEs exaustively in addition to showing the potential of organosulfonic acids as environmentally benign lixiviants for REEs extraction from coal ash. We have also shown how process optimization can be achieved using advance technologies while using organisulfonic acids. Moreover, we have shown current and future global market trends regarding the production of select organosulfonic acids, and the anticipated global increase in their production motivates the use of organosulfonic acids as viable lixiviants for REEs extraction from caol ash deposits.

To establish a human colony in a planetary body different from the terrestrial one, will entail to join those factors that can favour the good development of life in that place. However, which of these possible parameters can be categorized as essential when referring to the creation of a shelter for a long stay? Human beings, willing to abandon their natural environment in order to open new extra-terrestrial settlements for present and future generations, have to stay long hours cloistered in a volume built in a quite hostile environment a priori. They deserve to find a habitat which not only makes them feel protected, with the tranquillity and comfort that entails, but also provides an environment capable to transmit desire to live and be. Astroikos. Term whose suffix Oikos ("house", in Greek) defines in classical antiquity the set of goods and people that constituted the basic unit of society, allows us to identify the new planetary habitat as the possible refuge of a multidisciplinary team of astronauts aiming at colonizing other worlds. This would be based on four fundamental pillars: 1. The humanization of Space Architecture. 2. The possibility of the use of indigenous materials, resources and natural geological structures, as well as the recycling of elements of space vehicles. 3. Self-construction. 4. Security.

The mineralogical indices, e.g., Quartz Index (QI), Carbonate Index (CI), Mafic Index (MI) for ASTER multispectral thermal infrared (TIR) data have been applied to various geological materials. The indices are proved to be robust in extracting geological information at the local scale. Considering the relatively narrow spatial coverage of each ASTER scene compared to LANDSAT, many scenes are needed when mosaicking the images to be mapped at regional scales. We develop a system to search ASTER data for a target area given the vast and expanding ASTER data archive. The data is then conditioned, prioritized, and the indices are calculated before finally mosaicking the imagery. The maps of the indices covering the very wide region of the central Tibetan Plateau are produced with this system. The characteristic features of the indices relating to their geology in the study area are analyzed and discussed. Many interesting lithological and structural information that are not currently well understood in the central Tibetan Plateau, the highest and most extensive plateau in the world, with an average elevation of over 4,500 meters above sea level, for example, distributions of the mafic-ultramafic rocks along the suture zones, the quarzitic and marine sedimentology accreted to the Eurasian continent and sulfate layers related to the Tethys and neo-Tethys geological setting can be retrieved from the processed ASTER images.

As matrix representations of magic labelings of related hypergraphs, magic squares and their various variants have been applied to many domains. Among various subclasses, trimagic squares have been investigated for over a hundred years. The existence problem for trimagic squares with singly even orders and orders 16n has been solved completely. However, very little is known for the existence of trimagic squares with other even orders except for the only three examples and three families. We construct normal trimagic squares by using product constructions, row-square magic rectangles, and trimagic pairs of orthogonal diagonal Latin squares. We give a new product construction: For positive integers p, q, and r having the same parity other than 1, 2, 3, 6, if normal p × q and r × q row-square magic rectangles exist, then a normal trimagic square with order pqr exists. As its application, we construct normal trimagic squares of orders 8q^3 and 8pqr for all odd integers q not less than 7 and p,r ∈ {7, 11, 13, 17, 19, 23, 29, 31, 37}. Our construction can easily be extended to construct multimagic squares.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

This study concerns the transport and retention of polydisperse micron-sized (16 ± 6 µm) of microplastics (MPls) in porous media under varying flow rate conditions. Sorption kinetics were modeled using first-order reversible and irreversible kinetic sorption models, with sensitivity analyses providing insights into each sorption parameter's effect. Both numerical modeling and experimental measurements were employed to assess sand filter retention rates. The impact of flow rate on sorption reveals variations in distribution coefficient (Kd), mass transfer coefficient (β), and irreversible sorption rate (K1). Lower flow rates are correlated with higher Kd and β values, indicating an increase in sorption and diminished mass transfer rates. The findings revealed that an increase in Kd resulted in a more gradual sorption process with a decrease in peak concentration, whereas changes in β influenced the rate of sorption and peak concentration to a lesser extent compared to Kd. Lower K1 values are associated with higher peak concentrations and decreased retention efficiency. Retention rates were evaluated by a numerical model and found as 28 ± 1% at a flow rate of 31 ml min⁻¹ and 17 ± 1% at 65 ml min⁻¹. The introduction of MPls into soil environments has been noted to modify transport dynamics into soil. As a result, these alterations effects hydrological characteristics of soil, thereby impacting quality of groundwater and agricultural output. The mean absolute error (MAE) of 6% between modeled and observed retention rates suggests minor discrepancies. This study highlights the importance of examining retention efficiency and the accuracy of numerical models in porous media during MPl transport.

Most empirical work on sources of economic growth for different countries lack country-specific empirical evidence to guide policy choices in individual developing countries and previous studies of factor productivity tend to focus on the entire economy or a single sector. In this study, we use the recently developed growth accounting tools to explicitly determine the sources of economic growth at both national and sectoral levels in Zambia between 1970 and 2013. We use data from World Development Indicators and Zambia’s Central Statistical Office. On average, total factor productivity (TFP) contributes about 5.7% to economic growth. Sectoral analysis shows that agriculture contributes the least to GDP and that within each sector; factors that contribute to growth differ. Structural transformation has been slow and contributed to the observed inefficiency. We outline the implications of the observed growth and provide recommendations.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P<0.05), left hippocampus volume (LHV, β: -0.02435, P<0.01) and right hippocampus volume (RHV, β: -0.02544, P<0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P<0.05) and LHV (β: -0.01173, P<0.05) and RHV (β: -0.01193, P<0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P<0.05; RHV, β: -0.005527, P<0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

In this study, the separation conditions of UHPLC-QTOF-MS and the extraction conditions of QuEChERS were optimized. The analytical process for determining Broflanilide residues in different soil types was successfully established and applied to its adsorption, desorption and leaching in soil. Broflanilide was extracted from soil with acetonitrile as extraction solvent, and purified with 50 mg PSA + 150 mg MgSO4. The modified UHPLC-QTOF-MS method was used for determination. In different types of soil, the average recovery of Broflanilide was 87.7% -94.38%, and the RSD was lower than 7.6%. In the analysis and determination of the adsorption, desorption and leaching properties in four soils, the RSD was less than 9.2%, showing good stability and can be applied to the analysis and determination of the residue of Broflanilide in different soils.

In order to investigate the size distributions and seasonal variations of carbonaceous aerosols (OC and EC), the carbonaceous species were collected and then analyzed by using a 9-stage Anderson-type aerosol sampler and DRI Model 2001A Thermal/Optical Carbon Analyzer on the typical industrial city Nanjing in Yangtze River Delta, China in the summer, autumn and winter of 2013 and spring of 2014. OC, EC, SOC and POC exhibited obvious seasonal variations, with the highest level in winter (39.1±14.0, 5.7±2.1, 23.6±11.7 and 14.1±5.7 μg•m^-3) and the lowest level in summer (20.6±6.7, 3.3±2.0, 12.2±3.8 and 8.4±4.1 μg•m^-3), and were mainly centralized in PM_1.1 in four seasons. The concentrations of OC in PM_1.1 varied in the order of winter > autumn > spring > summer, while EC ranked in the order of autumn > winter > summer > spring. In the PM_1.1-2.1 and PM_2.1-10, the concentrations of OC and EC decreased in the sequence of winter > spring > autumn > summer. The size spectra of OC, EC and SOC had bimodal distributions in four seasons, except for EC with four peaks in summer. The size spectra of POC varied greatly with seasons, exhibiting bimodal distribution in winter, trimodal distribution in spring and summer, and four peaks in autumn. The OC/EC ratios were 7.0, 6.3, 7.6 and 6.9 in spring, summer, autumn and winter, respectively, which demonstrated the abundance of secondary organic aerosols in Nanjing. The sources of carbonaceous aerosol varied significantly with seasons, and were dominated by vehicle exhaust, coal and biomass burning in PM_2.1, and dominant by dust, coal and biomass burning in PM_2.1-10.

The permanent protection of groundwater and surface sources of drinking water in the required raw water quality from contamination is the primary foundation of preserving the life of society and the entire engineering infrastructure operability not only in the Czech Republic but also in other countries of the world. One of the basic ways of contamination prevention enhancement and risk mitigation of putting a water source out of operation is the identification of the given risk as well as soil contamination monitoring. The purpose of this study is to understand specific aspects of contamination threats to drinking water sources and determine possible solutions to eliminate the risk, shown in the example case study in the Czech Republic conditions. Based on the findings, a proposal to enhance the prevention of water source contamination has been elaborated in the form of recommendations regarding the ways and means used to monitor the risk areas and to implement technical measures so as to eliminate or terminate the specified risk. A complex approach based on the integration of interdisciplinary factors and methodology is required to minimize the threats of aquatic ecosystems contamination in the Czech Republic.

The Feni Island group is located at the southeastern end of the NW trending Ta-bar-Lihir-Tanga-Feni (TLTF) island chain, northeastern Papua New Guinea. This island chain is renowned for hosting alkaline magmas, geothermal activity, copper-gold mineralization and mining. The purpose of this paper is to present the geological observations of Feni Island within the context of the regional tectonic setting and evolution of the TLTF. The TLTF arc is a younger arc situated within the Greater Melanesian Arc, specifically within the New Ireland Basin bounded by New Ireland to the west and the extinct Kilinailau Trench in the east. The formation of the TLTF is attributed to post-subduction extensional tectonics relating to the opening of the Manus Basin and the magma is sourced from subduction-modified upper mantle. Normal, ex-tensional faulting is observed throughout the TLTF.

The Anthropocene has created a new cartography where various discursive levels are intertwined. It unites two fields of knowledge: geology and anthropology. In the 19th century, Romanticism challenged the separation between natural sciences and spirit sciences. With the Anthropocene a geological era is established, but with an epistemological dimension: environmental catastrophes are not a passive "object", they become an agent of social and political change. Images of the world (Weltbild) turn nature into an animated whole that challenges the dual vision: observer and observed. There is no nature without "observer", nor geology without anthropology. The Anthropocene modifies the foundations of our view of the world where we had excluded life. This is how concepts such as symbiogenesis, homeostasis, etc., which make visible and try to explain phenomena that are otherwise inexplicable. The Naturwissenschaft by J.W. Goethe is a point of support, with all these ideas that develop in the 20th century and anticipate the Anthropocene term of the 21th century. While the concepts of "belief" and "science" continue to be sharpened, rehabilitating "old quarrels" around anthropology, cosmology, theology, etc. The dignity of man is at stake.

Oil and petroleum are strategic resources of great importance to national security. Petroleum and hydrothermal gold deposits may form together, with similar evolutionary trends in their formation, migration, and enrichment. Petroleum reservoirs and gold deposits are closely coupled under certain geological conditions. The solubility of gold in crude oil and its forms of occurrence are important in determining the mechanisms of interaction between gold and petroleum and in facilitating the recovery of gold from gold-bearing petroleum. In this study, the occurrence of gold in crude oil from the Linnan Depression in the Bohai Bay Basin, China, was studied using inductively coupled plasma–mass spectrometry and X-ray photoelectron spectroscopy. Concentrations of gold in crude oil from the Linpan and Shanghe oilfields averaged 44.5 ppb, which is well above the minimum concentration required for hydrothermal gold mineralization. Gold has an affinity with carbon, oxygen, and sulfur, and its concentration in crude oil is positively correlated with total acid and sulfur contents. We speculate that gold may exist in crude oil as complexes with organic acids or thiols, with crude oil thus being a transport medium for gold.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Studies on Medical Geology have up till recently tended to emphasise the harmful effects of geological material and processes. This is perhaps justifiable, given the realisation that many environmental diseases could have causal links with some geo-environmental variables as co-factors, making such studies extremely valuable in the improvement of diagnoses and therapy. However, this review aims to show that in addition to the high value of such research, studies conducted on the beneficial properties of Earth materials also have considerable merit, given their enormous potential for assuaging a wide range of environmental health disorders. For instance, certain geological materials including clay minerals contain active substances that show considerable promise in various applications such as pharmaceutical formulations, aesthetic medicine, and indigenous medicine. This review synthesises current knowledge of how certain geological materials can be exploited in formulating remedies for some human health problems. Reports of the therapeutic uses of clay minerals, zinc oxide (zincite), zeolite, and kaolin are appraised. The review shows that ancient and contemporary use of geological materials such as clay minerals have played crucial roles in the treatment of several human diseases, with recent and ongoing research revealing further development in these applications. Well strategised clinical trials using available resources could give impetus to further research in elucidating the potential of various geomaterials as innovative clinical remedies for some human diseases and infections as well as aid the proper scientific documentation of their natural uses.

Geomathematics is extremely important in geosciences, particularly in the geology. The key for any geomathematical analysis is the definition of a typical model to be applied for further prognosis, either through deterministical or stochastical approaches. The selection of the appropriate procedure is presented in this paper. Two different geomathematical subfield datasets were used in subsurface geological mapping and palaeontology and different biostatistics applications, representing important geomathematical subfields in the Croatian geology. The different subsurface interpolation methods, tested, validated and recommended for application, were used to obtain the best possible outcome in reservoir modelling, in the cases with small datasets. Cross-validation may be selected as the main selection criteria, applied to the Croatian part of the Pannonian Basin System (abbr. CPBS). Recent advances in biostatistics applied in palaeontology and case studies from Croatia are also presented, where biometric studies are of significant importance in fossil biota. Data, methods and problems in geosciences is a vast subject, and address a wide spectrum of fundamental science. Because geology includes subsurface and surface geology, and very different datasets regarding variable and number of data, here are chosen two representative case study groups with original samples from Northern Croatia. Subsurface mapping has been presented on limited petrophysical datasets from the Northern Croatian, Miocene, hydrocarbon reservoirs. Biostatistics has been presented on very different samples, allowing to achieve paleoenvironmental reconstructions of size of relevant fossils, as dinosaurs or other species and their paleoenvironments. All examples highlight examples of the valuable application of geomathematical tools in geology. The results, cautiously validated and correlated with other, non-numerical (indicator, categorical) geological knowledge, are of enormous assistance in creating better geological models.

The NP method was used to elucidate the contributions of vehicles and coal combustion to seasonal and long-term atmospheric PM-bound Pyr and 1-NP concentrations in Kanazawa, Kitakyushu, Shenyang, and Shanghai in the Western Pacific region from 1997 to 2021. Among the four cities, Kanazawa demonstrated the lowest Pyr concentration. The contribution of vehicles to Pyr before and after 2010 were 35% and 5%, respectively. The 1-NP concentration reduced by a factor of more than 1/10. These changes can be attributed to the emission control from vehicles. Kitakyushu revealed the second lowest Pyr and the lowest 1-NP concentrations. Coal combustion was found to be the main contributor to Pyr, while its contribution to 1-NP increased from 9% to 19%. The large contribution of coal combustion is attributed to iron manufactures. Shenyang demonstrated the highest atmospheric Pyr concentration with its largest seasonal change. Vehicles are the largest contributors to 1-NP. However, coal combustion, including winter coal heating, contributed 97% or more to Pyr and more than 14% to 1-NP. Shanghai revealed the second highest Pyr and 1-NP concentrations, but the former was substantially lower than in Shenyang. Coal combustion was the major contributor, but the contribution of vehicles to Pyr was larger before 2010 similar to Kanazawa.

Background: Disparity in adult mortality (AM) with reference to social dynamics and health care has not been sufficiently examined. This study aimed to identify the gap in the understanding of AM in relation to religion, political stability, economic level, and universal health coverage (UHC). Methods: A cross-national study was performed with different sources of data, using the administrative record linkage theory. We created a new data set using data from the 2013 World Bank data catalogue by region, The Economist (Political instability index 2013), Stuckler David et al. (Universal health coverage, 2010), and religious categories of all UN country members. Descriptive statistics, a t-test, an ANOVA followed by a post hoc test, and a linear regression were used where applicable. Result: The average AM rate for males and females was 0.20 ± 0.10 and 0.14 ± 0.10, respectively. AM was significantly higher in economically weak countries, countries with political instability, countries with traditional religion, without achievement of UHC, and Sub-Saharan Africa (p<0.01). There was high disparity of AM between countries with and without UHC (F = male: 61.89, female: 51.85, p<0.001) and between groups with low and high income (F = male: 36.33, female: 42.39, p<0.001). UHC and political stability would significantly reduce AMR by > 0.41 in both sexes and high economic status would reduce male AMR by 0.44, and female AMR by 0.70, in relation to countries without UHC, with political instability, and low economic status. Conclusions: Disparities in AM can be reduced after the achievement of UHC and economically productive activities for those adults affected by conflict and political unrest.

This paper presents GeoFlood, a new open-source software package for solving shallow water equations (SWE) on a quadtree hierarchy of mapped, logically Cartesian grids managed by the parallel, adaptive library ForestClaw (Calhoun and Burstedde, 2017). The GeoFlood model is validated using standard benchmark tests from Neelz and Pender (2013) and against George (2011) results obtained from the GeoClaw software (Clawpack Development Team, 2020) for the historical Malpasset dam failure problem. The benchmark test results are compared against GeoClaw and software package HEC-RAS (Hydraulic Engineering Center - River Analysis System, Army Corp of Engineers) results (Brunner, 2018). This comparison demonstrates the capability of GeoFlood to accurately and efficiently predict flood wave propagation on complex terrain. The results from comparisons with the Malpasset dam break show good agreement with the GeoClaw results and are consistent with the historical records of the event.

Syros Island, Cyclades complex, central Aegean Sea, Greece, is a prime locality for the study of processes active in deep levels of orogens and is world famous for its exceptionally well preserved glaucophane schist-to eclogite-facies lithologies. Glaucophane schists and eclogites are witnesses of one of the fundamental tectonic processes operating on planet Earth. Results of geological research on Syros have contributed a lot to our present understanding of why and how these processes work that make oceans disappear, how mountain ranges can start to form, how magma chambers form to feed volcanoes, how subduction mechanisms can trigger earthquakes and lead to tsunamis, and a series of other spectacular or very impressive phenomena which have been observed and studied throughout the earth s window offered in that particular place of the world. The description, interpretation and evaluation of the important geological heritage of Syros, in combination with a preliminary SWOT analysis, showed the geotourism potential of the region. The results of this paper are intended to constitute a valuable tool for enhancing and raising awareness of the geological heritage of the island of Syros, with regard to the added value activities to be developed on a sustainable basis.

Groundwater represents a pivotal asset in conserving natural water reservoirs for potable consumption, irrigation, and diverse industrial uses. Nevertheless, human activities intertwined with industry and agriculture contribute significantly to groundwater contamination, highlighting the critical necessity to appraise water quality for safe drinking and effective irrigation. This research primarily focused on employing the Water Quality Index (WQI) to gauge water's appropriateness for these purposes. However, the generation of an accurate WQI can prove time-intensive owing to potential errors in sub-index calculations. In response to this challenge, an artificial intelligence (AI) forecasting model was devised, aiming to streamline the process while mitigating errors. The study collected 422 data samples from Mirpurkash, a city nestled in the province of Sindh, for a comprehensive exploration of the region's WQI attributes. Furthermore, the study probed into unraveling the interdependencies amidst variables in the physiochemical analysis of water. Diverse machine learning classifiers were employed for WQI prediction, with findings revealing that random forest and gradient boosting eclipsed other algorithms, achieving an accuracy rate of 99%. In close pursuit were SVM and XGBoost, registering accuracy scores of approximately 95% and 93%, respectively, while KNN and Decision Trees garnered accuracy rates of 88% and 87%, respectively. In addition to WQI prediction, the study conducted an uncertainty analysis of the models using the R-factor, providing insights into the reliability and consistency of predictions. This dual approach, combining accurate WQI prediction with uncertainty assessment, contributes to a more comprehensive understanding of water quality in Mirpurkash and enhances the reliability of decision-making processes related to groundwater utilization

Packaged water consumption has grown rapidly in urban areas of many low and middle income countries, but particularly in Ghana. However, the sources of water used by this growing packaged water industry and its implications for water resource management and transport-related environmental impacts have not been described. This study aimed to assess the spatial distribution of regulated packaged water production in Ghana, both in relation to demand and for natural mineral water, to hydrogeological characteristics. 764 addresses for premises licenced to produce packaged water from 2009-2015 were mapped and compared to regional sachet water consumption and beverage import/export data examined. We find evidence to suggest packaged water is transported shorter distances in Ghana than in developed countries. For natural mineral waters, producers should be able to address the most widespread water quality hazards (including high salinity, iron and nitrates) in aquifers used for production through reverse osmosis treatment. The study suggests there is scope to integrate beverage product and groundwater regulatory databases to support groundwater management.

The assessment outcomes of regional susceptibility to geological disasters can directly indicate the extent and intensity of risks within the study area, thus, providing targeted guidance for disaster management efforts. This study selects eight evaluation indicators, namely elevation, gradient, terrain relief, lithology of strata, normalized difference vegetation index, distance from the fault, distance from road, and distance from the river. The study focuses on Huize County in Yunnan Province as the research area, utilizing the certainty factor (CF) and random forest (RF) models for evaluating the susceptibility to geological disasters. The non-geological disaster points in the study area are determined using the deterministic coefficient prior model, and the deterministic coefficient values for each evaluation factor serve as the classification data for the random forest model. The optimal parameters for the random forest are selected through iterative calculations of bag error in PyCharm, while the weight of the evaluation factor is determined based on the ran-dom forest model with the optimal parameters. The results of geological disaster susceptibility zoning in Huize County are obtained by overlaying the weighted deterministic coefficients of each evaluation factor. The accuracy of the evaluation results is verified using zoning statistics and ROC curves with a test sample of 30% of the points. The results demonstrate the high accuracy of the model in evaluating the susceptibility to geological disasters in Huize County. Compared to the single deterministic coefficient model, this approach offers advantages in terms of reliability and accuracy. The evaluation results can serve as a scientific reference for related work in Huize County.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

Good hand hygiene has proven to be essential in reducing the uncontrolled spread of human pathogens. Cold atmospheric plasma (CAP) may provide an alternative to disinfecting hands with ethanol-based handrubs when hand washing facilities are unavailable. CAP can be safely applied to the skin if the energy is well controlled. In this study, RF and DC plasma sources was built with a pin-to-mesh electrodes configuration inside a fused silica tube of 5 mm of inner diameter. Microbiological assays based on EN 13697:2015+A1:2019 using Escherichia coli DSM 682 or Staphylococcus epidermidis DSM 20044 were used to examine the antimicrobial effect of various plasma conditions. Metal and silicone disks that model skin were used as inoculation matrices. The prototype air radio frequency (RF) CAP achieved significant disinfection in the MHz range on stainless steel and silicone substrates. This is equivalent to half the performance of direct current CAP, which is only effective on conductive substrates. Using only electricity and air CAP could, with further optimization, replace or complement current hand disinfection methods, and mitigate the economic burden of public health crises in the future.

Sustainability of current energy policies and known mid-term policies are analised in their multiple facets. First an overview is given about the trend of global energy demand and energy production, analysing the share of energy sources and the geographic distribution of demand, on the basis of statistics and projections published by major agencies. The issue of sustainability of the energy cycle is finally addressed, with specific reference to systems with high share of renewable energy and storage capability, highlighting some promising energy sources and storage approaches.

This work studies the discontinuities features of sedimentary flysch materials in a 100 km2 area belonging to the Basque Arc. Such materials are common in this Spanish Alpine region located in the north of the Iberian Peninsula. A total of 33 outcrops are investigated by an intensive geotechnical investigation including geomechanical stations, boreholes and mechanical laboratory tests. Two flysch units are characterized: the Upper Aguinaga Formation or siliciclastic flysch, and the Lower Itziar Formation or calcareous flysch. Differences between both flysch formation are found. Joints in the siliciclastic flysch formation present an undulated roughness, with a spacing narrower and a persistence lower than in the calcareous flysch formation, which exhibits higher friction angles, although roughness is essentially planar. In addition, the potential of using Artificial Intelligence (AI) techniques, particularly Artificial Neural Networks and Support Vector Machine, to estimate the Geological Strength Index (GSI) from the Rock Quality Design (RQD) and some discontinuities features (spacing, persistence, aperture and roughness) is investigated. AI techniques are found to be satisfactory, being the Support Vector Machine with a linear kernel the technique which achieves the best performance.

Geologists employ high-spatial-resolution (HR) remote sensing (RS) data for many diverse applications as they effectively reflect detailed geological information, enabling high-quality and efficient geological surveys. Applications of HR RS data to geological and related fields have grown recently. By analyzing these applications, we can better understand the results of previous studies and more effectively use the latest data and methods to efficiently extract key geological information. HR optical remote sensing data are widely used in geological hazard assessment, seismic monitoring, mineral exploitation, glacier monitoring, and mineral information extraction due to high accuracy and clear object features. Compared with optical satellite images, synthetic-aperture radar (SAR) images are stereoscopic and exhibit clear relief, strong performance, and good detection of terrain, landforms, and other information. SAR images have been applied to seismic mechanism research, volcanic monitoring, topographic deformation, and fault analysis. Furthermore, a multi-standard maturity analysis of the geological applications of HR images using literature from the Science Citation Index reveals that optical remote sensing data are superior to radar data for mining, geological disaster, lithologic, and volcanic applications, but inferior for earthquake, glacial, and fault applications. Therefore, geological remote sensing research needs to be truly multidisciplinary or interdisciplinary, ensuring more detailed and efficient surveys through cross-linking with other disciplines. Moreover, the recent application of deep learning technology to remote sensing data extraction has improved automatic processing and data analysis capabilities.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

Recent studies have emphasized the influence of resettlement factors on the mental health of refugees resettling in developed countries. However, little research has addressed gender differences in the nature and influence of resettlement stressors and sources of resilience. We address this gap in knowledge by investigating how gender moderates and mediates the influence of several sources of distress and resilience among 259 Afghan refugees residing in northern California. Gender moderated the effects of four factors on levels of distress. Intimate and extended family ties have little correlation with men’s distress levels, but are strongly associated with lower distress for women. English ability is positively associated with lower distress for women, but not men. In terms of gender ideology, traditionally oriented women and egalitarian men have lower levels of distress. And experiencing greater dissonant acculturation increases distress for men, but not women. The influence of gender interaction terms is substantial and patterns may reflect difficulty adapting to a different gender order. Future studies of similar populations should investigate gender differences in sources of distress and resilience, and efforts to assist new arrivals might inform them of changes in gender roles they may experience, and facilitate opportunities to renegotiate gender roles.

One of the most important factors impacting quality of content in Wikipedia is presence of credible sources. By following references readers can verify facts or find more details about described topic. A Wikipedia article can be edited independently in any of over 300 languages, even by anonymous users, therefore information about the same topic may be inconsistent. This also applies to use of references in different language versions of a particular article, so the same statement can have different sources. In this paper we analyzed over 40 million articles from the 55 most developed language versions of Wikipedia to extract information about nearly 200 million references and find the most popular and reliable sources. We presented 10 models for the assessment of the popularity and reliability of the sources based on analysis of meta information about the references in Wikipedia articles, page views and authors of the articles. Using DBpedia and Wikidata we automatically identified the alignment of the sources to a specific domain. Additionally, we analyzed the changes of popularity and reliability in time and identified growth leaders in each considered months. The results can be used for quality improvements of the content in different languages versions of Wikipedia.

Exploration geochemistry is an essential method for discover new mineral areas. However, with the increase of exploration degree, relying solely on "strong, broad and multiple" anomalies to guide exploration work has become increasingly challenging. How to effectively identify valuable geochemical information remains a hot and frontier topic in the field. Thus we proposed a geological connotation method (GCM) that provides an objective geological connotation to big geochemical data based on regional geological and geochemical characteristics of known typical deposits. There are mainly two types of geochemical anomalies expression: (1) the metallogenic intensity anomaly map (MIAM) obtained by accumulating specific anomalous elements, which directly reflects the degree of material exchange and superposition modification during mineralization; (2) the metallogenic type anomaly map (MTAM) obtained by accumulating the mineralization concentration coefficients of elements related to a certain genetic type, which can highlight the anomalies caused by a specific genetic type of deposit. These have been tried and applied in the exploration of the Gangdese, North Himalayas, Nyenchen Tanglha and other metallogenic belts in Tibet, and have made a series of breakthroughs in mineral resources exploration represented by Qulong, Zhunuo and Zhaxikang. The advantage of GCM is that it not only solves the problem of missing ore in the verification of "strong, broad and multiple" anomalies, but also can quickly and preferably delineate the strongest mineralized areas, and better overcome the influence of numerous factors on the anomalies, such as the chemical nature of elements, redox environment, geomorphic landscape and weathering and stripping, so that the anomaly evaluation becomes simple, objective and highlights the regularity.

The Anthropocene has created a new cartography. Various disciplines and discourses overlap each other. Two fields of knowledge: geology and anthropology are unified in one single concept. The Axial Age separated everyday practices from an unbiased and objective view of the world. Romanticism, in the nineteenth century, challenged the separation between the natural sciences and the sciences of the spirit. Paul J. Crutzen and Eugene Stoermer had two distinct parts; a first establishes "a period of time" the second an "epistemic tool". This paper is intended to illustrate the epistemological dimension of the Anthropocene. The Anthropocene defines the present geological epoch as dominated by humans. Eduard Suess, Antonio Stopani, Teilhard de Chardin, Vladimir Vernadsky etc., a century ago, anticipated the concept of Anthropocene. "Noösphere" is a term from the "world of thought". The hypothesis of an earth as a living organism, which is inspired by J.W. Goethe's "Naturwissenschaft", allows two disciplines to be inte-grated into one term: geology and anthropology. We have atmospheric phenomena that are in-compressible without presupposing life. The Anthropocene modifies the foundations of our vi-sion of the world. In the Gaia Hypothesis we find the same roots as in the Anthropocene concept: Goethe, Vernadky, etc. The concepts of symbiogenesis, homeostasis, etc., allow us to formulate new questions. This paper analyzes the reconfiguration of relations between the earth and all its inhabitants. It is, for the social sciences, a challenge: a metamorphosis of our vision of the world is taking place.

In the coming years, the Anthropocene Working Group (AWG) will submit its proposal on the ‘Anthropocene’ as a new geological epoch to the International Commission on Stratigraphy (ICS) for approval. If approved, the proposal will be send to the International Union of Geological Sciences (IUGS) for ratification. If the proposal is approved and ratified, the ‘Anthropocene’ will be formalised and the Holocene Series/Epoch will be officially terminated. Currently, the ‘Anthropocene’ is a broadly used term and concept in a wide range of scientific and non-scientific situations and, for many, the official acceptance of this term is only a matter of time. However, the AWG proposal, in its present state, seems to not fully meet the ICS requirements for a new geological epoch. This paper asks what could happen if the current ‘Anthropocene’ proposal is not formalised by the ICS/IUGS. The possible stratigraphic alternatives are evaluated on the basis of the more recent literature and the personal opinions of distinguished AWG and ICS members. The eventual impact on environmental sciences and on non-scientific sectors, where the ‘Anthropocene’ seems already firmly rooted and de facto accepted as a new geological epoch, are also discussed.

Uncertainty is the main source of risk of geological hazards in tunnel engineering. Uncertainty information not only affects the accuracy of evaluation results, but also affects the reliability of decision-making schemes. Therefore, it is necessary to evaluate and control the impact of uncertainty on risk. In this study, the problems in existing entropy-hazard model such as inefficient decision-making and failure of decision-making are analysed, and an improved uncertainty evaluation and control process are proposed. Then the tolerance cost, the key factor in the decision-making model, is also discussed. It is considered that the amount of change in risk value (R1) can better reflect the psychological behaviour of decision-makers. Thirdly, common attribute decision models, such as the expected utility-entropy model, are analysed, and then the viewpoint of different types of decision-making issues that require different decision methods is proposed. The well-known Allais paradox is explained by the proposed methods. Finally, the engineering application results show that the uncertainty control idea proposed here is accurate and effective. This research indicates a direction for further research into uncertainty, and risk control, issues affecting underground engineering works.

Metaverse has become an emerging trend for both academia and industry, and it seems to concern the next generation of the Internet. Although it is still in its grassroots, metaverse is estimated to bring disruption to people’s lives. One of the effects concerns the generation of new value oppor-tunities that don't exist in real life. These new types of value as well as their impact on people's lives must be explored. In this respect, this paper utilizes literature evidence to define the value types of metaverse, which are circulated with experts from the focus group on metaverse of the Interna-tional Telecommunications Union. Results uncover economic, public, and social values that metaverse generates, which can ensure its financial viability and the community's social sustaina-bility. The economic value sources come from both the industrial and the commercial sectors, while the public values concern citizen empowerment and government efficiency. The social values of metaverse concern employment growth, and the provision of immersive experiences in enter-tainment and education environments. Finally, this paper critically reviews their role for envi-ronmental, economic, and social sustainability. The literature review indicated that metaverse can on the one hand, enhance sustainability but on the other hand, it can cause environmental impact.

Abstract: The search for alternative protein sources to soy-bean meal (SBM) in animal feeding is a strategic objective to reduce production costs and contribute to a sustainable animal produc-tion. Spirulina, due to the high protein content, has emerged as a potential cost-effective, sus-tainable, viable and high nutritional value food resource for many animal species. Insect larvae (Tenebrio molitor and Hermetia illucens) are also considered potential alternatives to SBM, given their high edible percentage of almost 100%, as well as a protein value higher than that of vegetable proteins. Rapeseed meal and grain legumes, such as faba beans, peas, lupins and chickpea can also be used as locally producible protein ingredients. This study reviews the nutritional value of these potential alternatives to SBM in pig diets, effects on animal perfor-mance, digestion, immune system, physicochemical and sensorial characteristics of meat, in-cluding processed meat products of pork. Limits on their use in pig feeding are also reviewed to indicate gaps to be filled in future research on the supplementation level of these potential al-ternative protein sources into pig diets.

Boulder dynamics may provide essential data for the coastal evolution and hazards assessment and can be focused as a proxy for the onshore effect of intense storm waves. In this work, detailed observations of currently available satellite imagery of the Earth surface allowed to identify several coastal boulders displacements in the Southern Apulia coast (Italy), in a period between July 2018 and June 2020. Field surveys confirmed the displacements of several dozens of boulders up to several meters in size, also allowing the determination of the initial position for many of them. Archive weather analyses identified two possible causative storms during the same period, and calculations based on analytical equations are found in agreement with the displacement by storm waves for most of the observed boulders. The results help to give insights about the onshore effect of high storm waves on the coastal hydrodynamics and the possible future flooding hazard in the studied coast.

This study is describing airborne geophysical survey, carried out in Northeastern Russia (Archangelsk region) in order to aimed at geological mapping of Grib kimberlite pipe, which is known to have strong presence of remanent magnetization. Airborne data were inverted using two techniques, the magnetization vector inversion (MVI) and a QDIK inversion, a proprietary algorithm developed at the Irkutsk State University (ISTU), which allows extracting four parameters from airborne magnetic data (magnetic susceptibility, inclination, declination and Koeniksberger ratio). The inversion results were further analyzed and verified against the known geology of the Grib kimberlite. The study allowed to better map geology of Grib kimberlite using only uninvasive (remote sensing) technology

Earthquakes are one of the most catastrophic natural phenomena. After an earthquake, earthquake reconnaissance enables effective recovery by collecting building damage data and other impacts. This paper aims to identify state-of-the-art data sources for building damage assessment and provide guidance for more efficient data collection. We have reviewed 38 articles that indicate the sources used by different authors to collect data related to damage and post-disaster recovery progress after earthquakes between 2014 and 2021. The current data collection methods have been grouped into seven categories: fieldwork or ground surveys, omnidirectional imagery (OD), terrestrial laser scanning (TLS), remote sensing (RS), crowdsourcing platforms, social media (SM) and closed-circuit television videos (CCTV). The selection of a particular data source or collection technique for earthquake reconnaissance includes different criteria depending on what questions are to be answered by this data. We conclude that modern reconnaissance missions can not rely on a single data source and that different data sources should complement each other, validate collected data, or systematically quantify the damage. The recent increase in the number of crowdsourcing and SM platforms used to source earthquake reconnaissance data demonstrates that this is likely to become an increasingly important source of data.

Gravitational waves have been detected in the past few years from several transient events such as merging stellar mass black holes, binary neutron stars, etc. These waves have frequencies in a band ranging from a few hundred hertz to around a kilohertz to which LIGO type instruments are sensitive. LISA would be sensitive to much lower range of frequencies from SMBH mergers. Apart from these cataclysmic burst events, there are innumerable sources of radiation which are continuously emitting gravitational waves of all frequencies. These include a whole mass range of compact binary and isolated compact objects as well as close planetary stellar entities. In this work, quantitative estimates are made of the gravitational wave background produced in typical frequency ranges from such sources emitting over a Hubble time and the fluctuations in the h values measured in the usual devices. Also estimates are made of the high frequency thermal background gravitational radiation from hot stellar interiors and newly formed compact objects.

In China, the majority of mountainous regions are characterized by complex topography and a delicate, sensitive geological environment. Coupled with a generally underdeveloped infrastruc-ture and numerous unreasonable human engineering activities, these regions are often highly susceptible to geological disasters. Geological hazards can cause significant damage to human lives and property, impeding the development of mountainous areas. Consequently, researching the assessment of geological hazard vulnerability is crucial for disaster prevention, emergency management, and economic development in these regions. This study focuses on Xuanwei City and selects eight factors for evaluation, including elevation, gradient, slope aspect, normalized vegetation index, stratigraphic lithology, distance from faults, distance from rivers, and distance from roads. These factors are chosen based on a comprehensive analysis of the spatial and tem-poral distribution of geological hazards and disaster incubation conditions. Two paired models, the deterministic coefficient model + logistic regression model (CF+LR) and the information quan-tity model + logistic regression model (I+LR), were employed to quantitatively assess the study ar-ea. The accuracy of these models was evaluated using ROC curves and AUC values. The results indicate that: (1) The AUC values for the CF+LR and I+LR coupled models are 0.799 and 0.772, respectively, demonstrating that both models can objectively and reliably assess the vulnerability to geological hazards in the study area; (2) Based on the CF+LR model calculations, the geological hazard susceptibility of Xuanwei City can be categorized into four zones: extremely high suscepti-bility (6.09%), high susceptibility (31.08%), medium susceptibility (32.26%), and low susceptibility (30.57%); (3) The CF+LR model more accurately represents the evaluation results and offers a strong reference value.

Reducing meat consumption is better for the environment. Unfortunately, commercial plant-based meat substitutes are often more expensive than meat and thus have not seen widespread adoption. This paper analyzes commercially-available spirulina, soy, pea, and brown rice protein isolates characteristics to provide data for non-meat protein cost reductions. Thermal and rheological properties, viscosity, density, and particle size distribution are analyzed for further study on alternative protein-based food processing. Differential scanning calorimetry analysis produced dry amorphous-shaped curves and paste curves with a more distinct endothermic peak. Extracted linear temperature ranges for processing in food production for spirulina was 70-90ºC; soy protein was 87-116ºC; pea protein was 67-77ºC; and brown rice protein was 87-97ºC. Viscosity analysis determined each protein material was shear-thinning and that viscosity increased with decreased water concentration, with rice being an exception to the latter trend. The obtained viscosity range for spirulina was 15,100-78,000cP; soy protein was 3,200-80,000cP; pea protein was 1,400-32,700cP; and brown rice protein was 600-3,500cP. The results indicate that extrusion is a viable method for further processing of the protein isolates as this technique has a large temperature operating range and variable screw speed. Data provided here can be used to make single or multi-component protein substitutes.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

Wi-Fi fingerprinting positioning systems have been deployed for a long time in location-based services for indoor environments. Combining mobile crowdsensing and Wi-Fi fingerprinting systems could reduce the high cost for collecting the necessary data enabling the deployment of the resulting system for outdoor positioning in areas with dense Wi-Fi coverage. In this paper, we present the results attained in the designing and evaluation of an urban fingerprinting positioning system based on crowdsensed Wi-Fi measurements. We first asses the quality of the collected measurements, highlighting the influence of received signal strength on data collection. We then, evaluate the proposed system by comparing the influence of the crowdsensed fingerprints on the overall positioning accuracy for different scenarios. The evaluation helps gain valuable insight into the design and deployment of urban Wi-Fi positioning systems while also allowing the proposed system to match GPS-like accuracy in similar conditions.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

The Konya Closed Basin (Quaternary, Central Turkey) is a graben basin which expands toward the east-west and it is controlled by faults on three sides: The Konya fault zone in the west, the Divanlar fault zone in the east and the Karaömerler fault zone in the north. Calcretes developed in relation to fault systems in the Konya region are concentrated in areas where faults cut Quaternary aged terrestrial deposits. In this study, it is aimed to elucidate the deposition conditions, geochemistry and age (with ESR method) of the calcareous deposits associated with faults in the Konya Closed Basin. Calcretes in the region existing as coatings, dust, nodules and layers are in the form of dolocrete and clayey calcrete. Dolocretes were deposited in the Quaternary terrestrial sediments on the ophiolitic rocks and geochemical data point to an ultramafic source. Bacterial community, clay, quartz minerals and calcite cement are observed in the calcretes formed in areas with limestone basement. According to the results of ICP-MS analysis of samples taken from Konya calcretes, the %MgO contents are between 0.99 and 7.7; CaO%: between 34.71 and 50.71; %SiO2 between 3.22 and 20.59. %MgO in dolocretes are between 11.65 and 21.01; %CaO between 8.44 and 29.57; %SiO2 values between 4.48 and 9.17 The δ13C and δ18O isotope values of calcretes range from -3.87 to -7.62 and from -3.62 to -7.45 respectfully. Average δ13C values indicate that calcrete formation took place under pedogenic condition or in shallow groundwater. The calcretes deposited in 3 locations around the city of Konya (on the Konya fault zone) were dated by using the Electron Spin Resonance (ESR) method and ages between 217.47 and 389.85 ky were obtained. The calcrete samples taken from the fault planes (dip-slip normal fault bordering the Upper Cretaceous Ophiolitic Mélange and the Quaternary Karahüyük Formation) gave a relative age for faulting as being 292.86 ky. This first dating study conducted in the Konya Fault Zone has provided important clues to elucidate the formation history of Konya Closed Basin (KCB) and the paleo-seismological past of Konya.

Carbonate reservoirs, influenced by depositional and diagenetic processes and characterized by features like faults and vugs that impact storage capacity, require more than traditional Borehole Imaging logs (BHI) for accurate porosity data. This data is essential for geological assessments, production forecasting, and reservoir simulations. This work aims to address this limitation by developing methods to measure and monitor the sustainability of carbonate reservoirs and exploring the application of sustainability principles to their management. The study integrates BHI and conventional logs from two wells to classify porosity-based facies within the Barra Velha Formation (BVF) in the Santos Basin. The methodology involves four steps: (i) analyzing conventional logs; (ii) segmenting BHI logs; (iii) integrating conventional and segmented BHI logs using Self-Organizing Maps (SOM); and (iv) interpreting the resulting classes. Matrix porosity values and non-matrix pore sizes categorize the porosity into four facies (A to D). Facies A has high non-matrix porosity with 14,560 small megapores, 5,419 large megapores, and 271 gigapores (71.9%, 26.76%, and 1.34% of the 20,250 pores, respectively). Facies B shows moderate non-matrix porosity with 8,669 small megapores, 2,642 large megapores, and 33 gigapores (76.42%, 23.29%, and 0.29% of the 11,344 pores, respectively) and medium matrix porosity. Facies C exhibits low non-matrix porosity with 7,749 small megapores, 2,132 large megapores, and 20 gigapores (78.27%, 21.53%, and 0.20% of the 9,901 pores, respectively) and medium matrix porosity. Facies D has low non-matrix porosity with 9,355 small megapores, 2,346 large megapores, and 19 gigapores (79.82%, 20.02%, and 0.16% of the 11,720 pores, respectively) and low matrix porosity. The novelty of this work lies in integrating data from two sources to classify porosity across the Pre-Salt reservoir interval, serving as a proxy for preliminary litho-facies identification without core data. This study advances our understanding of carbonate reservoir sustainability and heterogeneity, offering valuable insights for robust, sustainable reservoir characterization and management in the context of global environmental and geological changes.

The underground injection and geological sequestration of carbon dioxide (CO₂) is a promising approach for reducing the levels of CO₂ in the atmosphere. To mitigate the leakage of CO₂ resulting from natural fracture networks in rock masses, the sequestration process is commonly accompanied by the injection of reactive Portland cement representing a coupled hydro-chemo-mechanical process. In this work, a numerical approach based on the unified pipe network method (UPM) is presented that considers the coupled permeation and diffusion processes with chemical precipitation. Most input parameters are derived from the published literature. The proposed approach is validated through a comparison with analytical solutions, which are applied to simulate the CO₂ sequestration process in a fractured rock mass. The results indicate that the long-term sequestration effect, which is highly influenced by the fracture distribution, can be captured effectively by the model. Consequently, the presented approach can assist engineers in properly designing the arrangement of boreholes and determining the concentration of the grouting material.

Leishmaniasis is considered one of the different neglected tropical diseases by the World Health Organization. Over the past few decades to tackle leishmaniasis, effective and novel drugs have progressed. But few are expensive some other medication shows poor effects and few drugs with long treatment lead to cause resistance. But it is very important to start a better medication against leishmania so researchers came to the front of the utilization of natural products which are considered a better option. Finding active compounds in medicinal plants is another alternative to currently accessible medications. Materials and methods: This study examined and reported the far more potential natural products used to treat disease caused by Leishmania spp. Leishmaniasis, plant metabolites, in vivo, in vitro, and treatment against leishmaniasis have been used as search terms in the Google Scholar, PubMed, and Science Direct databases, and only papers published between 2015 and 2021 have been chosen for further analysis. Results: The use of novel natural compounds with leishmanicidal action as well as the leishmanicidal activity of natural compounds against promastigote, axenic, and intracellular amastigote forms were included in roughly 20 research papers that were reviewed.Conclusion: Due to their capacity to selectively target parasites without harming host cell viability, herbal plants are a possible source of new anti-leishmanial medication. Future leishmaniasis treatments will draw on the isolated compounds as a source, completing those already offered in clinics.

Classical religious texts remain an essential part of human culture due to their undiminished influence on the advancement of civilization. Although their entirely divine origin is questioned repeatedly, explicit or implicit quoting and adherence to their basic guidelines are fundamental in modern society. In this respect, these documents’ inner structure and linguistic style appear to be pivotal. This paper considers the topic from the standpoint of small textual patterns classified using deep learning methods, traditionally applied to analyze short textual material like tweets. We divide the considered documents into small sequential chunks imitating tweets and categorizing them, classifying an entire text. The proposed method demonstrates that the religious text collections correspond to stable ”Twitter”-like structures that adequately reflect stylistic properties. So, concise word combinations seem to be an inborn textual attribute that adequately outlines the proposed multi-source authorship. This approach differs from traditional methods of analyzing classical religious documents, which are based on the consideration and interpretation of relatively long templates. The case study consists of three famous collections of Mosaic authorship in the Old Testament (Hebrew), Pauline authorship in the New Testament (Greek), and Al-Ghazali authorship (Arabic). The obtained results go well with most previously expressed evaluations and complement them with new implications, particularly in the authorship of two famous manuscripts attributed to Al-Ghazali.

Microplastics (MPs) are small pieces of plastics. They are ubiquitous in the environment and can enter the freshwater environment from surface run-off and wastewater effluent (treated and untreated), industrial effluent, degraded plastic waste, and atmospheric deposition. They are not usually destroyed but convert into one phase to another. They are a source of air pollution, occurring in dust and airborne fibrous particles. Mostly MPs are non-biodegradable while some MPs are biodegradable, which can be decomposed in the presence of ultraviolet (UV) light or by the action of microorganisms. Popular methods: chemical, spectroscopic, and thermo-analytical are available for the determination of the chemical composition and size of plastic particles. This chapter discusses the uses, health hazards, sources, and transport of MPs particles.

Remote sensing technology provides a new way to explore the earth for geoscience applications. In the context of continuous deepening of geological research and the vigorous development of geospatial information science, 3D geological modeling technology has become a research hotspot in the intersection of earth science and information science. The traditional 3D geological modeling technology refers to underground 3D modeling using geological data. This modeling method can only display the underground scene in 3D visualization, but cannot display the surface in detail. In this study, remote sensing technology is adopted to improve the traditional 3D geological modeling method, so that geological modeling can be integrated with remote sensing image, and a new 3D geological modeling method based on remote sensing technology is developed. This method can perform integrated 3D visualization of underground and aboveground scenes, which provides a new way for disaster prevention and reduction, geological prospecting and tectonic interpretation. The new 3D geological modeling method is mainly applied in the geological field, and has made new progress in multi-source heterogeneous geological data fusion, large-scale high-precision modeling, geological grid subdivision, attribute modeling technology, remote sensing image fusion and other aspects. Taking the Ya'an area as an example, this paper makes use of the new generation of 3D geological modeling technology to carry out 3D geological modeling and visual display. The 3D visualization in Ya'an area verifies the feasibility and effectiveness of the new 3D geological modeling method based on remote sensing technology in the current data environment.

Natural polysaccharides, which are described in this study, are some of the most extensively used biopolymers in food, pharmaceutical and medical applications, because they are renewable and have a high level of biocompatibility and biodegradability. The fundamental understanding required to properly exploit polysaccharides potential in the biocomposite, nanoconjugate, and pharmaceutical industries is depended on detailed research of these molecules. Polysaccharides are preferred over other polymers because of their biocompatibility, bioactivity, homogeneity, and bioadhesive. Natural polysaccharides have also been discovered to have excellent rheological and biomucoadhesive properties, which may be used to design and create a variety of useful and cost-effective drug delivery systems. Polysaccharide-based composites derived from natural sources have been widely exploited due to their multifunctional properties, particularly in drug delivery systems and biomedical applications. These materials have achieved global attention and are in great demand because to their biochemical properties, which mimic both human and animal cells. Although synthetic polymers account for a substantial amount of organic chemistry, natural polymers play a vital role in a range of industries, including biomedical, pharmaceutical, and construction. As a consequence, the current study will provide information on natural polymers, their biological uses, food and pharmaceutical applications.Keywords: Polymers Biopolymers, Excipient, Natural source, Food and Pharmaceutical applications.

This paper identifies preschool teachers' sources of stress, the times they experience high stress, and their ways of coping with stress levels. The study was conducted using a phenomenological design, one of the qualitative research models. The data were collected through semi-structured interviews with 36 preschool teachers working with children aged 0-6 in state and private schools. As a result of the content analysis, stressors were identified primarily at both interpersonal (positive, and effective interactions), and organizational levels (school management, and leadership style). It was also found that intense stress was experienced when children were difficult to control, such as during sleeping, eating, and cleaning. Finally, these results confirmed that the teachers used active/active behavioral, and passive/avoidant coping strategies. However, it was understood that preschool teachers perceived stress negatively, and did not see stress as a personal development situation. These results are discussed in terms of their ramifications for preschool education.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

In this work, the Pumped Storage Unit (PSU) is proposed to be integrated with wind-thermal generation system owned by a company whose aim is to maximize its profit through optimal self-scheduling of its units by finding the best bidding strategy in day-ahead energy market. The mathematical formulation of the scenario based unit-commitment and coordinated trading problem is formulated as a stochastic mixed integer linear program. The formulation takes into account several uncertain parameters; such as the wind power generation, energy market prices, and imbalances up/down prices. The expected total profit obtained from energy trading with and without coordinating pumped storage system (PSS) with thermal-wind generation system were compared, and a significant improvement in profit resulted from coordination was observed. Furthermore, coordination between PSS and wind-thermal generation improve the conditional value at risk (CVaR) which monitors the biding risk level.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

We improved a magnetic scanning microscope for measuring the magnetic properties of minerals in thin sections of geological samples at submillimeter scales. The microscope is comprised of a 200 µm diameter Hall sensor that is 142 µm from the sample; an electromagnet capable of applying to the sample up to 500 mT dc magnetic fields over a 40 mm diameter region; a second Hall sensor arranged in a gradiometric configuration to cancel the background signal applied by the electromagnet and reduce overall noise in the system; a custom-designed electronics to bias the sensors and provide adjustment for background signal cancelation; and a scanning XY stage with micrometer resolution. Our system achieves a spatial resolution of 220 µm with noise at 6.0 Hz of »300 nT_rms/(Hz)^1/2 in an unshielded environment. The magnetic moment sensitivity is 1.3 × 10⁻¹¹ Am².^1/2 We successfully measured the representative magnetization of a geological sample using an alternative model that takes into account the sample geometry and identified different micrometric characteristics in the sample slice.

Computation of Common Middle Point seismic sections and their subsequent time migration and diffraction imaging provides very important knowledge about the internal structure of 3D heterogeneous geological media and are key elements for successive geological interpretation. Full-scale numerical simulation, that computes all single shot seismograms, provides a full understanding of how the features of the image reflect the properties of the subsurface prototype. Unfortunately, this kind of simulations of 3D seismic surveys for realistic geological media needs huge computer resources, especially for simulation of seismic waves’ propagation through multiscale media like cavernous fractured reservoirs. In order to significantly reduce the query of computer resources we propose to model these 3D seismic cubes directly rather than the shot-by-shot simulation with subsequent CMP stacking. To do that we modify the well known "exploding reflectors principle" for 3D heterogeneous multiscale media by use of the finite-difference technique on the base of grids locally refined in time and space. To be able to simulate realistic models and acquisition we develop scalable parallel software, which needs reasonable computational costs. Numerical results for simulation of Common Middle Points sections and their time migration are presented and discussed.

The aim of this study was to examine the post-injury psychological impact looking for to avoid sources of health issues. We have analyzed differences in the stress, anxiety and depression levels between male and female football players who have suffered at least one injury during the last season played respect to similar players who have not been injured. A descriptive cross-sectional design was used. The participants were 187 football players and data on the player’s injuries were collected. A Self-reported Questionnaire collected number, type and severity of injuries sustained during the previous sports season (twelve months), and also the player’s current situation being injured or not injured. To evaluate the psychological variables, the DASS-21 questionnaire was used. Results indicated that the male injured players presented anxiety levels higher than those who were non-injured. When we observe the female players’ data, the stress levels of the non-injured ones are higher than those of the injured players. Regarding the non-injured athletes, results showed that the female non-injured players presented values in anxiety higher than those corresponding to the non-injured male players. Thus, sport injury affects mental health issues such as anxiety and stress, and in a different way regarding gender.

The 2020-2025 Dietary Guidelines for Americans recommends limiting intakes of saturated fat and added sugars (SF/AS) to 88% of the representative sample of U.S. adults. The top sources of SF were cheese, pizza, ice cream, and eggs. The leading sources of AS were soft drinks, tea, fruit drinks, and cakes and pies. This analysis reflects a parsimonious approach to reliably identify foods and beverages that contribute to SF/AS intakes in U.S. adults.

The aims of study was to evaluate the effects of rates, sources and timing of nitrogen application under cover of transgenic corn yield cultivated in Amazon Biome. The experiments were conducted in Parauapebas city, State of Pará, Brazil, in two years (2016/2017 and 2017/2018). The experimental design was randomized blocks, in a 5x2x2 factorial scheme, consisting of five rates of N (0; 45; 90; 135; and 180 kg ha-1), two nitrogen sources (urea and ammonium sulfate) and two application times of N (phenological stages V4 and V8), with four replications. The factor N rates promoted adjustment of linear equation (leaf area index, mass of thousand grains, and yield) and quadratic equation (dry mass of leaf index). Nitrogen fertilization promoted significant increases in mass of thousand grains and yield, obtaining the best results with 180 kg ha-1 of N applied at V4 phenological stage. Based on results obtained in two years of corn cultivated under conditions of Amazon Biome, the application of N at V4 phenological stage at rates of 121 to 131.39 kg ha-1 of N showed the best results for vegetative growth, while 180 kg ha-1 of N, regardless of source used, urea or ammonium sulfate, promoted greater grain weight and greater yield.

Methane (CH4) has attracted attention as not only synthetic natural gas, but also one of the hy-drogen carriers in terms of energy density. On the other hand, there exist bacterial ecosystems in nature that can decompose organic compounds to produce CH4 and CO2. In this study, Clostridi-um cellulovorans was first cultivated with pig manure (PM) as an unused biomass. Regarding the measurement of organic acids by high-performance liquid chromatography (HPLC), acetate and butyrate were increased in the C. cellulovorans medium containing 0.5% PM, while formate and lactate were decreased in it. Next, in comparison with carbon sources such as glucose, cellobiose, and acetate, cocultivation of C. cellulovorans and Methanosarcina mazei or microbial flora of me-thane production (MFMP) was performed in the C. cellulovorans medium. These results revealed that 0.5% acetate as the sole carbon source produced CH4 only by cocultivating C. cellulovorans and MFMP. Furthermore, MFMP was only cultivated with 1% acetate or 1% methane as a carbon source after precultivated with 0.5% glucose medium for 12 h. As a result, methane productivity of MFMP with 1% methanol medium was approximately eight times higher than that with 1% acetate medium. Finally, next-generation sequencing (NGS) analysis of MFMP after cultivation with 1% acetate or 1% methane was carried out. Interestingly, Methanofollis (0.211%) belonging to H2/CO2 -using methanogens (CO2 reduction pathway) was dominant in the 1% acetate medium for 72 h cultivation, whereas Methanosarcina siciliae (1.178%), M. barkeri (0.571%), and Methano-follis (0.490%) were major species in 1% methanol medium for 72 h cultivation. Since Methano-sarcina spp. are belonging to acetoclasts (acetoclastic pathway), methanol could promote to grow Methanosarcina spp. rather than acetate. Therefore, it seemed Methanosarcina spp. may play a key methanogenesis in MFMP. Thus, these results will provide important information for low cost biomethane production.

Cenospheres are hollow particles in fly-ash, a by-product of coal burning, and are widely used as reinforcement for developing low density composites called syntactic foams. This study investigates the physical, chemical, and thermal properties of cenospheres obtained from 3 different sources, CS1, CS2, and CS3, for the development of syntactic foams. Description of floatation method to separate broken particles is given, and it was seen that up to 11 % of the particles were damaged. Post heat treatment samples show development of SiO2 phase in the cenosphere, which is not present in the as received product. CS3 had the highest quantity of Si element, compared to the other two, showing the difference in the source quality. The particle size distribution for CS2 is very narrow while for the others is much broader. All censopheres have porous walls but the morphology of CS2 is the most uniform and smooth. For the application of metallic layer and subsequent consolidation via spark plasma sintering, CS2 was deemed the most physically, thermally, and chemically suitable.

Pronematus ubiquitus (McGregor) is a small iolinid mite that is capable of establishing on tomato plants. Once established, this mite has been shown to control both tomato russet mite, Aculops lycopersici (Tryon) (Acari: Eriophyidae) and tomato powdery mildew (Oidium neolycopersici L. Kiss). In the present study, we explored the nutritional value of various food sources in the laboratory. First, we assessed the reproduction of two food sources that P. ubiquitus can encounter on a tomato crop: tomato pollen and powdery mildew. In a second laboratory experiment, we evaluated the nutritional value of two types of prey mites: the astigmatid Carpoglyphus lactis L. (Acari: Carpoglyphidae) and the tarsonemid Tarsonemus fusarii (Acari: Tarsonemidae). Powdery mildew and C. lactis did not contribute to the reproduction, whereas tomato pollen and T. fusarii did allow egg-laying. However, Typha angustifolia pollen was a superior food source in both experiments. In a greenhouse trial on individual caged tomato plants, we evaluated the impact of pollen supplementation frequency on establishment of P. ubiquitus. Here, a pollen addition frequency of every other week was required to allow populations of P. ubiquitus to establish.

When the antioxidants in our immune system cannot neutralize or convert Reactive oxygen species into safe molecules at the rate at which it is produced then this imbalance is termed as “oxidative stress”. It is related with a wide array of diseases that includes cancer, diabetes, cardiovascular diseases, hypertension etc. These ROS species however are utmost essential for the proper functioning of human body which are produced as a consequence of partial oxidation of cellular metabolism performing essential functions such as protein phosphorylation, activation of several transcriptional factors, apoptosis, immunity, and differentiation. The sources by which these are produced can be broadly classified are intrinsic and extrinsic sources. There are variety of natural antioxidant enzymes of human body that combat against this oxidative stress. The extrinsic sources of ROS include the use of natural plants, extracted flavonoids and vitamins. In this review we will briefly explain how the sources of ROS, its essential function in human body, its elevation and associated damage to organs and effect on various diseases, and a hope of finding a way of how this oxidative stress can be exploited for therapeutic potential.

With the outbreak of the COVID-19 disease, the research community is producing unprecedented efforts dedicated to better understand and mitigate the affects of the pandemic. In this context, we review the data integration efforts required for accessing and searching genome sequences and metadata of SARS-CoV2, the virus responsible for the COVID-19 disease, which have been deposited into the most important repositories of viral sequences. Organizations that were already present in the virus domain are now dedicating special interest to the emergence of COVID-19 pandemics, by emphasizing specific SARS-CoV2 data and services. At the same time, novel organizations and resources were born in this critical period to serve specifically the purposes of COVID-19 mitigation, while setting the research ground for contrasting possible future pandemics. Accessibility and integration of viral sequence data, possibly in conjunction with the human host genotype and clinical data, are paramount to better understand the COVID-19 disease and mitigate its effects.

In recent years, tremendous progress has been made in the development of rare-earth ion doped tellurite glass laser sources, ranging from watt and multiwatt level fiber lasers to nanowatt level microsphere lasers. Significant success has been achieved in extending the spectral range of tellurite fiber lasers generating at wavelengths beyond 2 μm as well as in theoretical understanding. This review is aimed at discussing the state of the art of neodymium-, erbium-, thulium-, and holmium-doped tellurite glass fiber and microsphere lasers.

The recyclability of polystyrene, acrylonitrile butadiene styrene, polystyrene and polyvinylchloride waste and using them as a source for 3D printing were studied. Filaments of about 3 mm in diameter were extruded successfully with a small-size extruder. The processed filaments were tested on a broad range of parameters - glass transition temperature, tensile properties and a pyrolysis scenario were obtained. The measured parameters were compared with parameters of virgin counterparts presented in the literature. In order to estimate the toxicity of the recycled material, elemental analysis of the samples was done.

Shales are well known for their strong anisotrophic properties. The classical Athy’s model on the exponential porosity reduction with the depth commonly uses based on localities only. Shale compaction curve affects the results of the basin modeling as it is important input data, thus the standard compaction curve of shales needs to be established. This study provided a new data and complies available data of Thailand shales to propose the new empirical relationship among porosity, burial depth, and geological age. The numerical data of the geological time were estimated by the application from the relationship of velocity and depth in each geological ages. The variation of the Thailand shale data due to the different geological ages was found in this study. Finally, the standard curve of shale compaction proposed by Puttiwongrak et al. [9] was examined and confirmed by this research findings.

The growing population with changing consumption patterns in developing countries is causing significant challenges with regards to solid waste management. Plastic wastes are particularly problematic, with single-use plastics leaking into the environment, including the marine environment, at an unprecedented rate. Approximately 80 percent of ocean plastics come from land-based sources or about 8 million tons are dumped into the ocean every year. Thailand was identified as one of the top 10 countries ranked by mass of mismanaged plastic wastes, with more than 60,000 tons per year entering the ocean through multiple outlets, including rivers. In the environment, plastic wastes can be degraded into small sizes (less than 5 mm), called microplastics (MPs), which could contaminate the ecosystems and the food chain, including foodstuffs and water supply. Tap water samples collected from a water supply treatment plant and Academic Institutions 1 and 2 in central Thailand were found to contain MPs about 304 ±90, 270 ±109 and 386 ±102 particles/L, respectively. In addition, MPs concentrations of 211 ±70 and 122 ±60 particles/L were also found in drinking water samples collected from commercial bottled water and membrane filtration water, respectively. The MPs sizes of 0-50 µm were most abundant in both the tap and drinking water samples whose shapes were mainly fragments and fiber. These data indicated potential health risks to the people who consume these water sources, and recommendations for health impacts minimization were proposed.

This study evaluated eight herbal and fruit teas to produce kombucha beverages. Besides, the effect of initial sucrose concentration (10, 40, and 70% w/v) on kombucha fermentation from tea extracts was investigated. Kinetic characterization and modeling of kombucha fermentation were also performed. Results showed that kombucha beverages' characteristics and chemical content changed according to tea type and initial sucrose concentration. It was determined that as initial sucrose concentration increased, the consumed substrate concentration increased. The highest total biomass values were determined when green tea and pomegranate tea were supplemented with 70 g/L sucrose. The highest total phenolic content and antioxidant activity were achieved with green tea samples. The total acidity and phenolic substance concentration increased as fermentation progressed in general. The kinetic parameters including maximum consumption rate, sugar utilization, yield, biomass yield, maximum biomass, total acidity, phenolic production rate, and the phenolic result were computed depending on changing substrate concentration. Concerning kinetic modeling, proposed models (Logistic and Luedeking-Piret models) estimated satisfactorily experimental substrate consumption and total acidity values. Besides, total acidity was associated with the substrate consumption.

The aim of this review was to provide an update on the potential of cell therapies to restore or replace damaged and/or lost cells in retinal degenerative and optic nerve diseases, describing the available cell sources and the challenges involved in such treatments when these techniques are applied in real clinical practice. Sources include human fetal retinal stem cells, allogenic cadaveric human cells, adult hippocampal neural stem cells, human CNS stem cells, ciliary pigmented epithelial cells, limbal stem cells, retinal progenitor cells (RPCs), human pluripotent stem cells (PSCs) (including both human embryonic stem cells (ESCs) and human induced pluripotent stem cells (iPSCs)) and mesenchymal stem cells (MSCs). Of these, RPCs, PSCs and MSCs have already entered early-stage clinical trials since they can all differentiate into RPE, photoreceptors or ganglion cells, and have demonstrated safety, while showing some indicators of efficacy. Stem/progenitor cell therapies for retinal diseases still have some drawbacks, such as the inhibition of proliferation and/or differentiation in vitro (with the exception of RPE) and the limited long-term survival and functioning of grafts in vivo. Some other issues remain to be solved concerning the clinical translation of cell-based therapy, including (1) the ability to enrich for specific retinal subtypes; (2) cell survival; (3) cell delivery, which may need to incorporate a scaffold to induce correct cell polarization, which increases the size of the retinotomy in surgery and, therefore, the chance of severe complications; (4) the need to induce retinal detachment to perform the subretinal placement of the transplanted cell; and (5) the evaluation of the risk of tumor formation caused by the undifferentiated stem cells and prolific progenitor cells. Despite these challenges, stem/progenitor cells represent the most promising strategy for retinal and optic nerve disease treatment in the near future, and therapeutics assisted by gene techniques, neuroprotective compounds and artificial devices can be applied to fulfil clinical needs.

Research subjects of this study are four representative locations in the industrial complex, in the city of Banja Luka, Republic of Srpska, Bosnia and Herzegovina. 16 polycyclic aromatic hydrocarbons (PAHs) (∑16PAHs), humus and pH were determined. The main objective of the paper is to determine the concentration levels, to assess the probable sources of PAHs contamination in soil and groundwater and to determine the ecological risk. The ∑16PAHs in soil (at depths of 30 cm, 100 cm, 200 cm, 300 cm and 400 cm) ranged from 0.99 to 2.24 mg/kg, from 0.34 to 0.46, from 0.24 to 0.32, from 0.13 to 0.27 and from 0.13 to 0.47, with mean values of 1.70 mg/kg, 0.40 mg/kg, 0.28 mg/kg, 0.20 mg/kg and 0.26 mg/kg, respectively. The ∑16PAHs in groundwater ranged from 0.23 to 4.50 mg/m³, with a mean value of 1.42 mg/m³. Surface soil and groundwater are heavily contaminated. All values of ∑PAHs in soil layers were lower in the depths of the soil. Factor analysis indicates three sources of contamination, i.e. principal component (PC) PC1 (pyrogenic), PC2 (petrogenic) and PC3 (biomass), with 52.39%, 26.14% and 8.46% of the total variance, respectively. ∑PAH and PAHs indicate high ecological risk for most PAHs, which decreases with soil depth.

Building defects are very prevalent and contribute significantly to a building's economic value. There are numerous information sources on building defects that have a lot potential for learning more about building defects. This study aimed to identify the information sources used in previous building defect studies and to identify the motivation for carrying out such studies. To fulfil this aim a scoping study was carried out. The information sources identified included insurance companies, private databases, questionnaire surveys, lawsuits, building surveys, client complaint forms, and maintenance reports. This study found that insurance company and client complaint forms include the largest collection of real building defect cases, but such databases may lack detailed descriptions of the causes of the defects. The main purposes of building defects studies identified here included design challenges, identification of defects, building maintenance management, quality management, systematization in data collection, providing an overview of typical defects, and classifying defects. Identification was found to be the most common purpose, indicating that the industry wants to learn more. This study identified research gaps in the climate perspective in relation to building defects. Most of the studies focused on the economical perspective, and none focused on the carbon footprint perspective.

Femtoscopy is a unique tool to investigate the space-time geometry of the matter created in ultra-relativistic collisions. If the probability density distribution of hadron emission is parametrized, then the dependence of its parameters on particle momentum, collision energy, and collision geometry can be given. In recent years, several measurements came to light that indicated the adequacy of assuming a Lévy-stable shape for the mentioned distribution. In parallel, several new phenomenological developments appeared, aiding the interpretation of the experimental results, or providing tools for the measurements. In this paper we review and discuss some of these advances, phenomenological and experimental.

An estimation of the electric sources in the heart were conducted using a novel method, based on Huygens’ Principle, aiming at a direct estimation of equivalent bioelectric sources over the heart surface in real time. The main scope of this work was to establish a new, fast approach for the solution of the inverse electrocardiography problem. The study was based on recorded electrocardiograms (ECGs). Based on the Huygens’ principle, measurements obtained from a patient’s thorax surface were interpolated over the surface of the employed volume conductor model and considered as a secondary Huygens’ sources. These sources, being non-zero only over the surface under study, were employed to determine the weighting factors of the eigen-functions expansion describing the generated voltage distribution over the whole volume conductor volume. With the availability of the potential distribution stemming from measurements, the electromagnetics reciprocity theorem is applied once again to yield the equivalent sources over the pericardium. The methodology is self validated, since the surface potentials calculated from these equivalent sources are in very good agreement with ECG measurements. The ultimate aim of this effort is to create a tool providing the equivalent epicardial voltage or current sources in real time, i.e. during the ECG measurements with multiple electrodes.

We study wave patterns of gravity-capillary waves from moving localized sources within the classic setup of the problem of ship wakes. The focus is made on the co-existence of two wave systems with opposite signatures of group velocity relative to the localized source. It leads to the problem of choice of signs for phase functions of the gravity (“slow”) and capillary (“fast”) branches of the dispersion relation: the question generally ignored when constructing phase patterns of the solutions. We detail characteristic angles of the wake patterns: (i) angle of demarcation of gravity and capillary waves – “the phase Mach” cone, (ii) angle of the minimal group velocity of gravity-capillary waves – “the group Mach” cone, (iii, iv) angles of cusps of isophases that appear after a threshold current speed. The outer cusp cone is naturally associated with the classic cone of Kelvin for pure gravity waves. The inner one results from the effect of capillarity and tends to the “group Mach” pattern at high speeds of current. Amplitudes of the wave patterns are estimated within the recently proposed approach of reference functions for the problem of propagation of packets of linear dispersive waves. The effect of shape is discussed for elliptic reference sources.

The natural forests of Northern Thailand are the mother source of many utilisable natural products because of their diverse flora and fauna. Among many plant species found within Northern Thai forests, detergent plants are known for its distinctive cleansing properties. Several local species of detergent plants in Thailand are traditionally used by the locals and indigenous people. However, these plants may become extinct because their habitats have been replaced by industrial agriculture, and their uses have been replaced by chemically synthesised detergents. Researchers need to study and communicate the biology, phytochemistry, and the importance of these plants to conserve natural biodiversity of Northern Thailand. Of many utilisable detergent phytochemicals, natural saponins are known as bio-surfactant and foaming agents. Their physiochemical and biological properties feature structural diversity, which leads to many industrial applications. In this review, we explained the term “detergent” from the physiological mechanism perspective and the detergent effects of saponin. We also compiled a list of Thai local plants with cleansing properties focusing on the saponin-containing plants. Future studies should investigate information relative to plant environment, ethnobotanical data and bioactive compound content of these plants. The knowledge acquired from this study will promote the maintenance of the local biodiversity and the conservation of the detergent plant species found in Thailand.

In response to ever-increasing concerns regarding ecological degradation and societal impact, numerous stakeholders such as non-governmental organisations, government officials, end-users, the mass media, and community activists have compelled business organizations, particularly multi-national companies to lessen harmful greenhouse gases emissions associated with their production activities. Energy sector is one of the biggest harmful greenhouse gases emission producer, hence, decision-makers within the energy sector are forced to promote and build environmental friendly and sustainable power generation plants. To this end, the concept of sustainability in the electricity sector has attracted so much attention from academics and industrial practitioners over the last three decades. Albeit, an important number of sustainability assessment frameworks for electricity generating technologies are found in the current literatures, three major drawbacks have emerged from those frameworks. Firstly, there is a lack of a holistic and comprehensive sustainability assessment framework for different power generation plants. Secondly, from economic aspect, the most used model (Levelised Cost of Electricity) to measure the cost performance of various electricity generating technologies is biased and is not inclusive enough, because, it only considers the capital, Operations and Maintenance, and fuel costs. Hence, snubbing crucial elements to business decision. Lastly, in the current literature, there is no a single sustainability assessment model that considers all the phases of electrical energy’s lifecycle. Considering these flaws, the novelty of this study is the development of a new, holistic theoretical sustainability assessment framework for power generation plants. The developed theoretical model includes 19 impact categories, 52 potential indictors, and 10 end points environmental, economic, and social aspects.

How many different writers authored the huge number of texts attributed to Galen of Pergamum (129~216 AD), medical doctor and philosopher, a giant in the history of medicine? To find out which texts were his and which ones were written by others is known as the “Galenic Question”. We propose a “solution” to it through a multidisciplinary approach based: (a) on historical research and (b) on a mathematical analysis of the Greek texts. The historical approach has considered historical independent sources and anachronisms. The mathematical approach has been based on a mathematical theory concerning deep–language variables, rarely consciously controlled by any author, therefore capable of giving indications on similarity of texts, with little or no bias. The multidisciplinary approach has convinced us that at least three authors wrote the texts attributed to Galen. The first two very likely were real historical persons: (a) a certain Galen living between the end of the I century BC and the second half of the I century AD; (b) the historical Galen of Pergamum (II–III centuries AD) and (c) several unknown authors hiding under the name Galen, but surely living after Galen of Pergamum’s death.

Aiming at the difficult problem of broadband oscillation localization in power systems, the intel-ligent localization method of oscillation source based on the digital twin is proposed and the os-cillation source localization system based on the digital twin is constructed. Firstly, a digital twin-based oscillation source localization method and system architecture are proposed. Fur-thermore, an intelligent positioning method of oscillation source based on data-driven and mechanism fusion is proposed. It includes three steps: oscillation signal preprocessing, oscillation modal analysis and oscillation source localization. For the oscillation signal preprocessing, the generative adversarial imputation network is used to repair the missing samples, and the su-per-resolution technique is used to realize the super-resolution measurement of broadband os-cillation. In the oscillation modal analysis, the spectrum of the oscillation signal is extracted using the fast Fourier transform. To accurately locate the oscillation source, the branch potential energy is used as input to the data-driven model, such as LSTM and CNN. Finally, an oscillation source localization system is developed based on the digital twin workshop CloudPSS-XStudio, which can locate the oscillation source quickly and accurately.

Fungal infections pose a significant threat to human health, particularly in immunocompromised individuals. Due to several factors, such as the inappropriate use of antimicrobial drugs, the emergence of resistance in microorganisms, and increasing demand for less cytotoxic antifungal agents for immunocompromised patients, antifungal research has gained significant attention in recent years. Antifungal peptides, and among them, cyclic peptides, are a class of antifungal agents that have been under development since the 1960s. Using cyclic peptides as a promising approach for combating antifungal resistance in pathogenic fungi has gained significant attention in recent years. The identification of antifungal cyclic peptides from various sources has been possible due to the widespread interest in peptide research in recent decades. It is increasingly important to evaluate the narrow to broad-spectrum antifungal activity and the mode of action of synthetic and natural cyclic peptides for both synthesized and extracted peptides. This short review aims to highlight some of the antifungal cyclic peptides isolated from bacteria, fungi, and plants, taking into consideration the progress made in peptide research. Additionally, it provides a summary of synthetic cyclic peptides with antifungal activity and discusses the potential future of utilizing combinations of antifungal peptides from different sources. The review underscores the need for further exploration of the novel therapeutic applications of these abundant and diverse cyclic peptides.

Methane (CH4) has attracted attention as not only synthetic natural gas, but also one of the hy-drogen carriers in terms of energy density. On the other hand, there exist bacterial ecosystems in nature that can decompose organic compounds to produce CH4 and CO2. In this study, Clostridi-um cellulovorans was first cultivated with pig manure (PM) as an unused biomass. Regarding the measurement of organic acids by high-performance liquid chromatography (HPLC), acetate and butyrate were increased in the C. cellulovorans medium containing 0.5% PM, while formate and lactate were decreased in it. Next, in comparison with carbon sources such as glucose, cellobiose, and acetate, cocultivation of C. cellulovorans and Methanosarcina mazei or microbial flora of me-thane production (MFMP) was performed in the C. cellulovorans medium. These results revealed that 0.5% acetate as the sole carbon source produced CH4 only by cocultivating C. cellulovorans and MFMP. Furthermore, MFMP was only cultivated with 1% acetate or 1% methane as a carbon source after precultivated with 0.5% glucose medium for 12 h. As a result, methane productivity of MFMP with 1% methanol medium was approximately eight times higher than that with 1% acetate medium. Finally, next-generation sequencing (NGS) analysis of MFMP after cultivation with 1% acetate or 1% methane was carried out. Interestingly, Methanofollis (0.211%) belonging to H2/CO2 -using methanogens (CO2 reduction pathway) was dominant in the 1% acetate medium for 72 h cultivation, whereas Methanosarcina siciliae (1.178%), M. barkeri (0.571%), and Methano-follis (0.490%) were major species in 1% methanol medium for 72 h cultivation. Since Methano-sarcina spp. are belonging to acetoclasts (acetoclastic pathway), methanol could promote to grow Methanosarcina spp. rather than acetate. Therefore, it seemed Methanosarcina spp. may play a key methanogenesis in MFMP. Thus, these results will provide important information for low cost biomethane production.

Purpose –The basic purpose of this paper is to find out the librarians perceptions, skills, most effective and constrains to use social media for the marketing purposes in the University libraries and to examine how these libraries perceive the importance of social media marketing. Design/methodology/approach –A nation-wide online survey on University libraries in the Pakistan was conducted to flourish this study, and a total number of 161 responses were used to analyze collected data. Findings –This study revealed the application of social media in university Libraries is very high .The results also disclosed that University libraries observe social media as a substantial tool to increase marketing of library sources and services anticipate to increase their use. Practical implications –The findings of this study can help as a parameter for University libraries when engaging social media for marketing purposes in their libraries. Originality/value –This study calculated the present situation of social media use for marketing in the University Libraries environment, a background that has been under-study in the literature, from these perspectives: perceptions, Skills, effectiveness, practices and constrains

The characteristics of biogenic aerosols in urban area were explored by determining the composition, temporal distribution of saccharides in PM_2.5 in Shanghai. The total saccharides showed a wide range of 15.2 ng/m³ to 1752.8 ng/m³, with the averaged concentrations were 169.8 ng/m³，300.5 ng/m³，288.4 ng/m³，688 ng/m³ in spring, summer, autumn, and winter, respectively. The concerned saccharides include anhydrosaccharides (levoglucosan and mannosan), which were higher in cold seasons due to the increased biomass burning, saccharide alcohols (mannitol, arabitol, sorbitol) and monosaccharides (fructose, glucose), which showed more abundant in warm seasons attributed to the biological emissions. By PMF analysis, four emission sources of saccharides were demonstrated, including biomass burning, fungal spores, soil suspension and plant pollens. Resolution of backward trajectory and fire points showed a process of high concentrations of levoglucosan. We found that concentrations of anhydrosaccharides showed relatively stable under different pollution levels while saccharide alcohols exhibited an obvious decrease, indicated that biomass burning was not the core reason of the heavy haze pollution, however, and high level PM_2.5 pollution might inhibit effects of biological activities.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Danyore Valley area is a new prospect of copper-gold mineralization in the Gilgit-Baltistan province, Kohistan terrane, northern Pakistan. The mineralization is Cu-Au vein-type, localized within quartz veins and controlled by a fracture system mainly trending NW and NE. The host units belong to the Ladakh-Kohistan arc terrane, which covers northern Pakistan and north-western India and mainly comprises Precambrian basement units, Paleozoic to Cenozoic magmatic rocks, and sedimentary strata. The mineralized wall rocks consist of Mesozoic gabbro and diorite, which have undergone an intensive hydrothermal alteration. The study area, Danyore Valley, has yet to be explored. The geological background and mineralization type in literature are scarce. Moreover, the tectonic setting, petrogenesis, age, and magmatic evolution of the gabbro-diorite hosting unit still need to be better understood. Furthermore, the sources of metals and mineralized fluids and the types of mineralization and alteration are also unexplored. This research's contribution presents the field investigation, microscopic observations, whole rock geochemistry (major, trace, and REE), mineral analysis (EPMA), in situ LA–ICP–MS zircon U–Pb age dating, and zircon trace elements data for Danyore Valley Cu-Au prospect of Kohistan Batholith. The current research work's objectives are to (a) constrain the emplacement ages of the Danyore Valley host rocks, (b) determine the petrogenesis and tectonic environment of the gabbro-diorite wall rocks, and (c) identify the mineralization style and alteration patterns of Cu-Au occurrences. The U-Pb isotopic data of studied zircons from Danyore Valley diorite specimens yielded concordia ages from 111.60 ± 0.90 Ma to 112.18 ± 0.74 Ma. Correspondingly, the gabbro rock sample displayed a concordia age of 110.21 ± 0.99 Ma, indicating the crystallization time of the host bodies is mainly the early cretaceous period (∼110 Ma). The findings of this study reveal that the calc-alkaline affinity and arc-like geochemical characteristics of the gabbro and diorite rocks have been characterized by a significant enrichment in large-ion lithophile elements and an apparent depletion in high-field strength elements. The parent magma probably originated from a partial melting process of mantle depletion, and geochemical traits are characteristic of magmas associated with subduction zones. The Danyore Valley area of Kohistan terrane is defined by the existence of several mineralized quartz veins, which are mainly sulfide assemblages. The sulfide ore is mainly comprised of chalcopyrite, pyrite, and bornite, with a smaller amount of covellite and sphalerite and significant traces of gold, which are distributed mainly in sulfides. Copper and gold mineralization of Danyore Valley is associated with phyllic, propylitic, and carbonatization alteration assemblages. Metal-rich quartz veins exhibit a spatial correlation with diorite and gabbro rocks. The discovery of several surface Cu-Au vein-type mineralized areas accompanying outcrops of copper supergene enrichment at the Danyore Valley prospect is significant evidence (predictor patterns) of porphyry-style deposits in the Gilgit district, Kohistan terrane, northern Pakistan. This work also advocates the importance of the Danyore Valley prospect and Kohistan Batholith region for further detailed geological studies.

This comprehensive review is devoted to an under-exploited family of phenolic compounds, the coumarins, and the most relevant strands in which they are involved in some spirit beverages – wine spirit, brandy, whiskey, sugar cane spirits (rum and cachaça) and grape marc spirit – with great importance worldwide in terms of production, trade and consumption. It gathers the key discoveries on the topic considering the production process of each spirit beverage, the related sources of coumarins (different kinds of wood used in the ageing stage) along with the factors that govern them and can influence the sensory properties of the aged beverages. An overview of the analytical methods available for their identification/quantification is also included, as well as the corresponding trends for the advancement of knowledge in this field. Moreover, the remarkable role of coumarins as nutraceuticals, their importance as chemical markers for authenticity purposes, and their relationship with food safety of these spirit beverages are also addressed, highlighting the current gaps and issues, and providing clues for future research.

CO2, CH4 and CO are the most critical atmospheric gases in terms of their impact on the radiative system, air quality and health. This work provides information on the direction of source areas and potential sources of emissions and shows many aspects of these gases by a statistical analysis using bivariate polar diagrams and local weather conditions (e.g., temperature, wind speed and wind direction) recorded at the Lamto station (LTO, 6°31N and 5°02W) in Côte d’Ivoire over the 2014-2018 period. The results show that the main regions contributing to the high concentrations of CH4 (> 1925 ppb) and CO2 (> 420 ppm) in the GSS, GSP, PSS and PSP seasons are the North and Northwest sectors of Lamto. In these directions, CH4 and CO2 concentrations are associated with wind speeds less than 6 m.s-1, due to the influences of local sources as emissions resulting from the degradation of organic matter submerged during the impoundment of the Taabo dam, and/nor human activities linked to the practice of intensive agriculture. In addition, the high concentrations of CO (> 350 ppb) are observed in GSS in the North, North-West, North-East and East sectors for wind speeds less than or equal to 9 m.s-1, due to the influences of both local and distant sources. The correlation coefficients between CH4 and CO, and between CH4 and CO2 are positive and significant in all sectors. However, those calculated between CO2 and CO have showed both low and high values in all seasons.

Physical roots, exemplifications and consequences of periodic and aperiodic ordering (represented by Fibonacci series) in biological systems are discussed. The role and physical and biological roots of symmetry and asymmetry appearing in biological patterns is addressed. Generalization of the Curie-Neumann Principle as applied to biological objects is presented, briefly summarized as: “asymmetry is what creates a biological phenomenon”. The “up-bottom approach” and “bottom up” approaches to the explanation of symmetry in organisms are presented in detail. The “up-bottom approach”, implies that the symmetry of the biological structure follows the symmetry of media in which this structure is functioning; the “bottom-up” approach, in turn, adopt that the symmetry of biological structures emerges from the symmetry of molecules constituting the structure. A diversity of mathematical measures applicable for quantification of ordering in biological patterns is introduced. The continuous, Shannon and Voronoi measures of symmetry/ordering and their application to biology objects are addressed. The fine structure of the notion of “ordering” is discussed. Informational/algorithmic roots of ordering inherent for the biological systems are considered. Ordered/symmetrical patterns provide economy of biological information, necessary for algorithmic description of a biological entity. Application of the Landauer principle bridging physics and theory of information to the biological systems is discussed.

Geological disposal facilities for radioactive waste pose significant challenges for robust monitoring of environmental conditions within the engineered barriers that surround the waste canister. Temperatures are elevated, due to the presence of heat generating waste, relative humidity varies from 20% to 100%, and swelling pressures within the bentonite barrier can typically be 2-10 MPa. Here, we test the robustness of a bespoke design MEMS sensor-based monitoring system, which we encapsulate in polyurethane resin. We place the sensor within an oedometer cell and show that despite a rise in swelling pressure to 2 MPa, our relative humidity (RH) measurements are unaffected. We then test the sensing system against a traditional RH sensor, using saturated bentonite with a range of RH values between 50% and 100%. Measurements differ, on average, by 2.87% RH, and are particularly far apart for values of RH greater than 98%. However, bespoke calibration of the MEMS sensing system using saturated solutions of known RH, reduces the measurement difference to an average of 1.97% RH, greatly increasing the accuracy for RH values close to 100%.