Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

As a vital component of the terrestrial ecosystem, grassland accounts for one-third of the global vegetation system. Grassland degradation has been exacerbated due to extreme overgrazing in China's Inner Mongolia Autonomous Region (IMAR). While conservation was carried out as the Ecological Subsidy and Award Program (ESAP) to mitigate grassland degradation, little is known about its effectiveness in improving the biophysical conditions of grassland. This paper integrates the conceptual frameworks of total socio-environmental systems to assess how ecological systems respond to ESAP, investigate spatial heterogeneity of ESAP, and explore the meddling effects of socio-environmental interactions on ESAP. We integrate ecological, climate, and socioeconomic data and developed several hierarchical linear mixed models (HLMM) to investigate how these factors interact with ESAP in IMAR. Our findings prove that the above-ground biomass between 2011 and 2015 responds significantly to variations in socioeconomic conditions and ecological communities. Available land resources, hospital and medical facilities, and net farmer and herdsman income are the most critical factors contributing to grassland productivity. Primary industries like mining, total consumer retail value, farming, forestry, animal husbandry, fishery productions, and GDP are the most damaging factors affecting biomass. Our study recommends a regionally or locally tailored ecological recovery policy, instead of a generalized one, in the future effort to conserve grassland.

Timely and accurate acquisition of information on distribution of the crop planting structure in Loess Plateau of eastern Gansu Province, one of the most important agricultural areas in western China, is crucial for promoting fine management of agriculture and ensuring food security. In this study, the Object-Based Image Classification (OBIC), the Random Forest (RF) and Convolutional Neural Network (CNN) models were employed to classify the crop planting structure of four representative test areas in Qingyang City in a precise manner. Firstly, different optimal segmentation scales for various crops were selected using the Estimation of Scale Parameter 2 (ESP2) tool and the Ratio of Mean Difference to Neighbors(ABS) to Standard Deviation (RMAS)model. The images were then segmented through multiresolution segmentation combined with the Canny Edge Detection algorithm. Secondly, the L1 regularized logistic regression model was utilized to select and optimize 39 spatial feature factors including spectral, textural, geometric, and index features, in conjunction with phenological factors. Lastly, under the multi-level classification framework, the Random Forest (RF) classifier and Convolutional Neural Network (CNN) model, combined with object-based multiresolution segmentation, was used to classify the crop planting structure. The findings show that: Thanks to the Canny Edge Detection algorithm, we can obtain a more complete boundary of the segmented objects and improve the separability. The optimal segmentation scales for corn, vegetables, and buckwheat were found to be 55, 70, and 35, respectively, while wheat and apple had optimal segmentation scales of 65. In addition to phenological characteristics, the number of selected spatial features for corn, vegetables, buckwheat, wheat, and apple were 9, 7, 16, 12, and 10, respectively. The CNN model demonstrated high consistency with the RF model in the classification results, but the accuracy of RF model is higher than that of CNN model on the whole. The overall accuracy of classification using RF model in four test areas registered 91.93%, 94.92%, 89.37% and 90.68%, respectively. This paper introduced crop phenological factors, effectively improving the extraction precision of shattered agricultural planting structure in the Loess Plateau of eastern Gansu Province. Its findings have important application value in crop monitoring, management, food security and other related fields.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Spatial and temporal variation of the free electron concentration in the ionosphere affects SAR interferograms, in particular at low radar frequencies. In this work the identification, estimation and compensation of ionospheric path delay phases in PALSAR-3 and NISAR-L interferograms is discussed. Both these L-band sensors acquire simultaneously SAR data in a main spectral band and in an additional, spectrally separated, narrower second band to support the mitigation of ionospheric path delays. The methods presented permit separating the dispersive and the non-dispersive phase terms based on the double-difference interferogram between the two available spectral bands and the differential interferogram of the main band. The applicability of the proposed methods is demonstrated using PALSAR-3-like data that was simulated based on PALSAR-2 SM1 mode data.

：Non-Euclidean data, such as social networks, and citation relationships between documents, has node information and structural information. Graph Convolutional Network(GCN) can automatically learn node features and association information between nodes. The core ideology of the graph convolutional network is to aggregate node information by using edge information, thereby generating a new node feature. In the process of updating node features, there are two core influencing factors. One is the number of neighboring nodes of the central node, the other is the contribution of the neighboring nodes to the central node. Due to the previous GCN methods not simultaneously considering the numbers and different contributions of neighboring nodes to the central node, we design the Adaptive Attention Mechanism(AAM). To further enhance the representational capability of the model, we utilize Multi-Head Graph Convolution(MHGC). Finally, we adopt cross-entropy(CE) loss function to describe the difference between the predicted results of node categories and the ground truth (GT). Combined with backpropagation, this ultimately achieves accurate node classification. Based on AAM, MHGC and CE, we contrive the novel Graph Adaptive Attention Network (GAAN). Experiments show that the classification accuracy has achieved outstanding performances on Cora, Citeseer and Pubmed datasets.

The existing segmentation-based scene text detection methods mostly need complicated post-processing, and the post-processing operation is separated from the training process, which greatly reduces the detection performance. The previous method, DBNet successfully simplified post-processing and integrated the post-processing into a segmentation network. However, the training process of the model took a long time for 1200 epochs and the sensitivity to texts of various scales was lacking, leading to some text instances being missed. Considering the above two problems, we design the text detection Network with Binarization of Hyperbolic Tangent(HTBNet). First of all, we propose Binarization of Hyperbolic Tangent (HTB), optimized along with which, the segmentation network can expedite the initial convergent speed by reducing the amount of epochs from 1200 to 600. Because features of different channels in the same scale feature map focus on the information of different regions in the image, to better represent the important features of all objects in the image, we devise the Multi-Scale Channel Attention(MSCA). Meanwhile considering that multi-scale objects in the image cannot be simultaneously detected, we propose a novel module named Fused Module with Channel and Spatial(FMCS), which can fuse the multi-scale feature maps from channel and spatial dimension. Finally we adopt cross entropy as the loss function, which measures the difference between predicted values and ground truths. The experimental results show that HTBNet compared with lightweight models has achieved competitive performance and speed on Total-Text(F-measure:86.0%, FPS:30) and MSRA-TD500 (F-measure:87.5%, FPS:30).

The experiences gathered during the past 30 years support the operational use of irrigation scheduling based on frequent multi-spectral image data. Currently, the operational use of dense time series of multispectral imagery at high spatial resolution makes monitoring of crop biophysical parameters feasible, capturing crop water use across the growing season, with suitable temporal and spatial resolutions. These achievements, and the availability of accurate forecasting of meteorological data, allow for precise predictions of crop water requirements with unprecedented spatial resolution. This information is greatly appreciated by the end users, i.e. professional farmers or decision-makers, and can be provided in an easy-to-use manner and in near-real-time by using the improvements achieved in web-GIS methodologies. This paper reviews the most operational and explored methods based on optical remote sensing for the assessment of crop water requirements, identifying strengths and weaknesses and proposing alternatives to advance towards full operational application of this methodology. In addition, we provide a general overview of the tools which facilitates co-creation and collaboration with stakeholders, paying special attention to these approaches based on web-GIS tools.

NiFe alloy nanoparticles/graphene oxide hybrid (NiFe/GO) was prepared for electrochemical glucose sensing. The as-prepared NiFe/GO hybrid was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results indicated that NiFe alloy nanoparticles can be successfully deposited on GO. The electrochemical glucose sensing performance of the as-prepared NiFe/GO was studied by cyclic voltammetry and amperometric measurement. Results showed that NiFe/GO modified glassy carbon electrode had sensitivity of 173 μA mM⁻¹cm⁻² for glucose sensing with a linear range up to 5 mM, which was superior to commonly used Ni nanoparticles. Furthermore, high selectivity for glucose detection can be achieved by NiFe/GO. All the results demonstrated that NiFe/GO hybrid was promising for using in electrochemical glucose sensing.

Smallsats are becoming the predominant electro-optical Earth observation (EO) imaging platforms. While atmospheric correction of smallsat data enhances its utility, an established pathway to do so may constrain accuracy and utility. The alternative, Closed-form Method for Atmospheric Correction (CMAC), developed for smallsat application provides surface reflectance derived solely from scene statistics. In a prior paper, CMAC closely agreed with Land Surface Reflectance Code (LaSRC) software for correction of the four VNIR bands of Landsat-8/9 images for conditions of low to moderate atmospheric effect over quasi-invariant warehouse-industrial targets. Those results were accepted as surrogate surface reflectance to support analysis of CMAC and LaSRC reliability for surface reflectance retrieval in two contrasting environments: shortgrass prairie and barren desert. Reliability was defined and tested through a null hypothesis: the same top-of-atmosphere reflectance under the same atmospheric condition will provide the same estimate of surface reflectance. Evaluated against the prior surrogate surface reflectance, the results found decreasing error with increasing wavelength for both methods. From 58 comparisons across the four bands, LaSRC average absolute error ranged from 0.59% (NIR) to 50.30% (blue). CMAC error was well constrained from 0.01% (NIR) to 0.98% (blue) sustaining the null hypothesis for reliability.

The atmospheric lightning is one of the natural disasters which need to be considered in the sustainable development. The National Remote Sensing Centre (NRSC) has installed 46 lightning detection sensors (LDS) across the country. These sensors work in radio frequencies having their detection range up to 1000 km with more than 98% detection efficiency within 300 km range. The network is put in a way that sensors have about 50% sensor-to-sensor overlap in their detection ranges to enable high geolocation accuracy and maintain redundancy. The NRSC-LDS network (LDSN) estimates the current associated with each cloud to ground (CG) lightning flash which can be utilized for the risk assessment. The current estimates from one network to the other need to be inter-calibrated and harmonized. Present study compares the LDSN current estimates with Lightning Location Network (LLN) estimates and results are discussed with their impact on the estimation of vulnerable zones. A case study of lightning-induced fire event is presented to showcase the importance of the currents associated with lightning for future planning.

With the growing demand for positioning services, angle-of-arrival (AoA) estimation or direction-finding (DF) has been widely investigated for applications in fifth-generation (5G) technologies. Many existing AoA estimation algorithms only require the measurement of the direction of the incident wave at the transmitter to obtain correct results. However, for most of the cellular systems such as Bluetooth indoor positioning system due to multipath and non-line-of-sight (NLOS) propagation, the indoor positioning accuracy is severely affected. In this paper a comprehensive algorithm is investigated that combines radio measurements from Bluetooth AoA local navigation systems with indoor position estimates obtained using particle filtering, which allows us to explore new optimised methods to reduce estimation errors in indoor positioning. First, particle filtering is used to predict the rough position of a moving target. Then, an algorithm with robust beam weighting is used to estimate the AoA of the multipath components. Based on this, a system of pseudo-linear equations for target positioning based on the probabilistic framework of PF and AoA measurement is derived. Theoretical analysis and simulation results show that the algorithm can improve the positioning accuracy by about 25.7% on average.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

Elevated blood glucose levels, known as glycemia, play a significant role in sudden cardiac arrest, often resulting in sudden cardiac death, particularly among those with diabetes. Understanding the internal mechanisms has been a challenge for healthcare professionals, leading many research groups to investigate the relationship between blood glucose levels and cardiac electrical activity. Our hypothesis suggests that glucose-sensing biophysics mechanisms in cardiac tissue could clarify this connection. To explore this, we adapted a single-compartment, computational model of the human atrial node's action potential. We incorporated glucose-sensing mechanisms with voltage-gated sodium ion channels using ordinary differential equations. Parameters for the model were based on existing experimental studies to mimic the impact of glucose levels on atrial node action potential firing. Simulations using voltage clamp and current clamp techniques showed that elevated glucose levels decreased sodium ion channel currents, leading to a reduction in the sinoatrial node action potential frequency. In summary, our mathematical model provides a cellular-level understanding of how high glucose levels can lead to bradycardia and sudden cardiac death.

Outliers seriously affect the accuracy in geometric model fitting. Previous works in coping with outliers involve threshold selection and scale estimation. However most scale estimators suppose the inlier distribution as a Gaussian model, which usually poorly meets the cases in geometric model fitting. Outliers, considered as the points with big residuals to all the true models, share common items with big values in quantized residual preferences, thus making the outliers gather away from the inliers in quantized residual preference space. In this paper we make use of this outlier consensus in quantized residual preference space by extending the usage of energy minimization to combine the model error and the spatial smoothness in quantized residual preference space for outlier detection. The energy minimization based outlier detection process follows an alternate sampling and labeling framework. After the outlier detection, an ordinary energy minimization method is employed to optimize the inlier labels, which also follows the framework of alternate sampling and labeling. The experimental results in this study show that the energy minimization based outlier detection method can detect most of the outliers in the data. Furthermore, the proposed energy minimization based inlier segmentation process segments the inliers into different models quite accurately. Overall, the performance of the proposed method is better than most of the state-of-the-art methods.

Elevated blood glucose levels, known as glycemia, play a significant role in sudden cardiac arrest, often resulting in sudden cardiac death, particularly among those with diabetes. Understanding this link has been a challenge for healthcare professionals, leading many research groups to investigate the relationship between blood glucose levels and cardiac electrical activity. Our hypothesis suggests that glucose-sensing mechanisms in cardiac tissue could clarify this connection. To explore this, we adapted a single-compartment, in-silico model of the human atrial node's action potential. We incorporated glucose-sensing mechanisms with voltage-gated sodium ion channels using ordinary differential equations. Parameters for the model were based on existing experimental studies to mimic the impact of glucose levels on atrial node action potential firing. Simulations using voltage clamp and current clamp techniques showed that elevated glucose levels decreased sodium ion channel currents, leading to a reduction in the sinoatrial node action potential frequency. In summary, our model provides a cellular-level understanding of how high glucose levels can lead to bradycardia and sudden cardiac death.

Traffic anomaly detection is crucial for urban management, yet current research is often confined to small-scale endeavors. This study collected nine months of real-time Wuhan traffic monitoring data from Amap. We proposed Traffic-ConvLSTM, a multi-scale spatial-temporal technique based on long and short-term memory networks (LSTM) and convolutional neural networks (CNN) to effectively achieve long-term anomaly detection at the city level. First, we convert the traffic flow data into image representation, which enables the capture of the spatial correlation between traffic flow and roads and the correlation between traffic flow and roads, as well as the surrounding environment. Second, The model utilizes convolution kernels of different sizes to extract spatial features at road-level, regional-level, and city-level scales, while incorporating temporal features of different time steps to capture hourly, daily, and weekly dynamics. Additionally, varying weights are assigned to the convolution kernels and temporal features of varying spatio-temporal scales to capture the heterogeneous strengths of spatio-temporal correlations within patterns of traffic anomalies. The proposed Traffic-ConvLSTM model exhibits improved performance over existing techniques in the task of identifying long-term and large-scale traffic anomaly occurrences. Furthermore, the analysis reveals significant traffic anomalies during holidays and urban sporting events. The diverse travel patterns observed in response to various activities offer insights for large-scale urban traffic anomaly management, providing recommendations for city-level traffic control strategies.

The mineralogical indices, e.g., Quartz Index (QI), Carbonate Index (CI), Mafic Index (MI) for ASTER multispectral thermal infrared (TIR) data have been applied to various geological materials. The indices are proved to be robust in extracting geological information at the local scale. Considering the relatively narrow spatial coverage of each ASTER scene compared to LANDSAT, many scenes are needed when mosaicking the images to be mapped at regional scales. We develop a system to search ASTER data for a target area given the vast and expanding ASTER data archive. The data is then conditioned, prioritized, and the indices are calculated before finally mosaicking the imagery. The maps of the indices covering the very wide region of the central Tibetan Plateau are produced with this system. The characteristic features of the indices relating to their geology in the study area are analyzed and discussed. Many interesting lithological and structural information that are not currently well understood in the central Tibetan Plateau, the highest and most extensive plateau in the world, with an average elevation of over 4,500 meters above sea level, for example, distributions of the mafic-ultramafic rocks along the suture zones, the quarzitic and marine sedimentology accreted to the Eurasian continent and sulfate layers related to the Tethys and neo-Tethys geological setting can be retrieved from the processed ASTER images.

This article describes the history of research and development of surface-penetrating radar, starting from the 60s in the USSR, and ending today in Russia and neighboring states formed after the collapse of the USSR. The outstanding role played in the initial period of this technology development by Prof. M.I. Finkelstein and his colleagues is highlighted. Their research had a significant impact on subsequent developments in modern Russia and the neighboring countries.

This study explores the potential of digital technologies for preserving cultural heritage through the case study of the Raya Gopura, an incomplete monument in Melukote, India. Employing a combination of terrestrial photogrammetry, drone-based photogrammetry and terrestrial laser scanning, the research team captured highly detailed 3D models of the structure. This non-destructive approach offers a comprehensive digital record for future research and preservation. Furthermore, for the conjecture for the Raya Gopura two possible purposes: an entrance to a planned fort or a gateway to the temple are perceived through the collective intelligence (CI) approach. These insights inform a conjectural architectural drawing of the potentially completed monument. The 3D models hold significant potential for various applications, including tourism, education, and architectural research, with the potential for immersive experiences through VR and AR technologies. The study demonstrated the effectiveness of digital tools in heritage preservation, not only safeguarding the Raya Gopura but also offering valuable in-sights for future research and public engagements.

This study explores the potential of digital technologies for preserving cultural heritage through the case study of the Raya Gopura, an incomplete monument in Melukote, India. Employing a combination of photogrammetry (terrestrial and drone-based) and terrestrial laser scanning, the research team captured highly detailed 3D models of the structure. This non-destructive approach offers a comprehensive digital record for future research and preservation. Furthermore, consultations with experts yielded two possible purposes for the Raya Gopura: an entrance to a planned fort or a gateway to a temple. These insights inform a conjectural architectural drawing of the potentially completed monument. The 3D models hold significant potential for various applications, including tourism, education, and architectural research, with the potential for immersive experiences through VR and AR technologies. In conclusion, this study demonstrates the effectiveness of digital tools in heritage preservation, not only safeguarding the Raya Gopura but also offering valuable insights for future research and public engagement.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

The Microwave Humidity and Temperature sounder (MWHTS) on board the Fengyun (FY)-3C satellite measure the outgoing radiance form the Earth surface and atmospheric constituents. MWHTS makes measurements in the isolated oxygen absorption line near 118 GHz and the vicinity of strong water vapor line around 183 GHz, can provide fine vertical distribution structure of both atmospheric humidity and temperature. However, in order to obtain the accurate soundings of humidity and temperature by the physical retrieval method, bias between the observed radiance and those simulated by radiative transfer model from the background or first guess profiles must be correct. In this study, two bias correction methods are developed through the correlation analysis between MWHTS measurements and air mass identified by the first guess profiles of the physical inversion, one is the linear regression correction (LRC) and the other is neural networks correction (NNC), representing the linear and nonlinear nature between MWHTS measurements and air mass, respectively. Both correction methods have been applied to MWHTS observed brightness temperatures over the geographic area (180° W-180° E, 60° S-60° N). The corrected results are evaluated by the probability density function of the difference between corrected observations and simulated values and the root mean square error (RMSE) with respect to simulated observations. The numerical results show that the NNC method perform better, especially in MWHTS channels 1 and 7-9 whose peak weight function heights are close to the surface. In order to assess the effects of bias correction methods proposed in this study on the retrieval accuracy, a one-dimensional variational system was built and applied to the MWHTS uncorrected and corrected brightness temperatures to estimated atmospheric temperature and humidity profiles, The retrieval results show that the NNC has better performance which is to be expected. An indication of the stability and robustness of NNC method is given which suggests that the NNC method has promising application perspectives in the physical retrieval.

This research investigates precision enhancement in regional quasi-geoid refinement through ADS80 tri-linear array scanning stereoscopic imagery for aerial triangulation, coupled with GNSS gravity-potential modeling. Acquiring stereoscopic imagery and analyzing triangulation accuracy with the ADS80 camera, we performed this study over the Qinghai-Tibet Plateau's elevated, desolate terrain, collecting 593 GNSS points following high-precision stereoscopic imagery model. Utilizing 12 gravity satellite models, we computed geoid heights and China 1985 Yellow Sea elevations for 28 benchmarks and GNSS points, thereby refining the Qinghai Province Quasi-Geoid Model (QPQM) using geometric techniques. The findings reveal that POS-assisted ADS80 stereoscopic imagery yields high-precision triangulation with maximal horizontal and elevation accuracies of 0.083/0.116 cm and 0.053/0.09 cm, respectively, across five control point arrangements. The RMSE of normal heights for 1985, processed via these GNSS points, achieved decimeter precision. By applying error corrections from benchmarks to the 1985 elevation data from gravity satellites and performing weighted averaging, the precision of EGM2008, SGG-UGM-2, and SGG-UGM-1 models improved to 8.61 cm, 9.09 cm, and 9.38 cm, respectively, surpassing the QPQM by 9.22 cm to 9.99 cm. This research demonstrates that the proposed methods can significantly enhance the precision of regional quasi-geoid surfaces. Additionally, these methods offer a novel approach for rapidly establishing regional quasi-geoid models in the uninhabited areas of the Qinghai-Tibet Plateau.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Background: Several kinds of research say that adjuvant blood glucose and blood pressure are usual, but an efficient solution for medical application count remains. This review analyzes the pandemic blood pressure and blood glucose to identify the publications which tell about the clinical practices and research gaps in systematic research.Methods: A study guides to identify the research of Blood Pressure (BP) and Blood Glucose. In order to analyze the recent innovations and research on BP and Blood glucose, the relevant publications and literature from journals were identified.Results: Co-morbidity of BP and Blood glucose is reported as very high. The commonness of blood pressure is thrice as high in type I diabetes patients and almost two times higher in type II diabetes patients when compared to others without Diabetes. The pervasiveness of getting depression is more in the female when compared with men. A detailed study about the linkage of BP and blood glucose tells that the relationship between them is not exactly clear.Limitations: Nearly all reviews providing the linkage of BP and blood glucose are with some limitations and they are not providing any clear conclusion.Conclusions: Present research tells that people having high blood glucose will have a greater chance of getting high blood pressure. More research is needed to state the linkage between BP, blood glucose, and the growth of diabetes mellitus issues and to provide support for managing Diabetes.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

Recent advancements in deep learning have spurred the development of numerous novel semantic segmentation models for land cover mapping, showcasing exceptional performance in delineating precise boundaries and producing highly accurate land cover maps. However, to date, no systematic literature review has comprehensively examined semantic segmentation models in the context of land cover mapping. This paper addresses this gap by synthesizing recent advancements in semantic segmentation models for land cover mapping from 2017 to 2023, drawing insights on trends, data sources, model structures, and performance metrics based on a review of 106 extracted articles. Our analysis identifies top journals in the field, including MDPI Remote Sensing, IEEE Journal of Selected Topics in Earth Science, and IEEE Transactions on Geoscience and Remote Sensing, IEEE Geoscience and Remote Sensing Letters, ISPRS Journal Of Photogrammetry And Remote Sensing as the leading journals. We find that research predominantly focuses on land cover, urban areas, precision agriculture, environment, coastal areas, and forests. Geographically, 35.29% of the study areas are located in China, followed by USA (11.76%), France (5.88 %), Spain (4%) and others. Sentinel-2, Sentinel-1, and Landsat satellites emerge as the most commonly used data sources. Benchmark datasets such as ISPRS Vaihingen & Potsdam, LandCover.ai, DeepGlobe, and GID datasets are frequently employed. Model architectures predominantly utilize encoder-decoder, and hybrid convolutional neural network-based structures because of their impressive performances, with limited adoption of transformer-based architectures due to its computational complexity issue, and slow convergence speed. Lastly, this paper highlights existing key research gaps in the field to guide future research directions.

Global warming leads in general to a reduction in precipitations and non-rainfall water contributions such as dew. The present study, carried out in Gujarat (India) for 17 years between 2005 and 2021, shows however a rare increase of the rain falls and dew condensation, the latter related to an increase in relative humidity and a decrease in wind amplitudes. Rain was obtained from meteo stations. Dew was calculated from an energy model and meteo data from 15 meteo stations (14 in India and 1 in Pakistan) and compared to early and dedicated measurements in 13 sites. Maps of dew, rain and their relative contributions during the period are provided. They show that, while rain mainly occurs during the monsoon (June to September), dew forms during the dry season (October to April). This water resource was mapped over the Gujarat state of India by using a kriging process. According to the site, the dew/rain ratios can represent between 4.6% (Ahmedabad) to 37.2% (Jamnagar) on the whole period of 17 years. This positive evolution, which is observed since 2015-2017, is likely to continue in the future.

We have designed cell penetrating peptides that target the leucine zipper transcription factors ATF5, CE-BPB and CEBPD and that promote apoptotic death of a wide range of cancer cell types, but not normal cells, in vitro and in vivo. While such peptides have the potential for clinical application, their mechanisms of action are not fully understood. Here, we show that one such peptide, Dpep, compromises glucose uptake and glycolysis in a cell-context-dependent manner (in about 2/3 of cancer lines assessed). These actions are dependent on induction of tumor suppressor TXNIP (thioredoxin interacting protein) mRNA and protein. Knockdown studies show that TXNIP significantly contributes to apoptotic death in those cancer cells in which it is induced by Dpep. The metabolic actions of Dpep on glycolysis led us to explore combinations of Dpep with clinically approved drugs metformin and atovaquone that inhibit oxidative phosphorylation and that are in trials for cancer treatment. Dpep showed additive to synergistic activities in all lines tested. In summary, we find that Dpep induces TXNIP in a cell-context-dependent manner that in turn sup-presses glucose uptake and glycolysis and contributes to apoptotic death of a range of cancer cells.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

High-precision displacement sensing has been widely used across from both scientific researches and industrial applications. The recent interests in developing micro-opto-electro-mechanical systems (MOEMS) have given rise to an excellent platform for miniaturized displacement sensors. Advancement in this field during past years is now yielding integrated high-precision sensors which show great potential in applications ranging from photoacoustic spectroscopy to high-precision positioning and automation. In this review, we briefly summarize different techniques for high-precision displacement sensing based on MOEMS, and discuss the challenges for future improvement.

The GLUT members belong to a family of glucose transporter proteins that facilitate glucose transport across the cell membrane. The mammalian GLUT family consists of thirteen members (GLUTs 1-12 and HMIT). Humans have a recently duplicated GLUT member, GLUT14. Avians express the majority of GLUT members. The arrangement of multiple GLUTs across all somatic tissues signifies the important role of glucose across all organisms. Defects in glucose transport have been linked to metabolic disorders, insulin resistance and diabetes. Despite the essential importance of these transporters, our knowledge regarding GLUT members in avians is fragmented. It has been clear that there are no chicken orthologs of mammalian GLUT4 and GLUT7. Our examination of GLUT members in the chicken revealed that some chicken GLUT members do not have corresponding orthologs in mammals. We review the information regarding GLUT orthologs and their function and expression in mammals and birds, with emphasis on chickens and humans.

Background. Transferrin receptor 1 (TfR1), glucose transporter 1 (GLUT1), and CD98hc are candidates for targeted therapy at the blood-brain barrier (BBB). Our objective was to challenge the expression of TfR1, GLUT1, and CD98hc in brain capillaries by the histone deacetylase inhibitor (HDACi) valproic acid (VPA). Methods. Primary mouse brain capillary endothelial cells (BCECs) and brain capillaries isolated from mice injected intraperitoneally with VPA were examined using RT-qPCR and ELISA. Targeting to the BBB was performed by injecting monoclonal anti-TfR1 (Ri7217)-conjugated gold nanoparticles measured using ICP-MS. Results. In BCECs co-cultured with glial cells, Tfrc mRNA expression was significantly higher after 6 h VPA returning to baseline after 24 h. In vivo Glut1 mRNA expression was significantly higher in males, but not females', receiving VPA, whereas Cd98hc mRNA expression was unaffected by VPA. TfR1 increased significantly in vivo after VPA, whereas GLUT1 and CD98hc were unchanged. Uptake of anti-TfR1-conjugated nanoparticles was unaltered by VPA in spite upregulated TfR expression. Conclusions. VPA upregulates TfR1 in brain endothelium in vivo and in vitro. VPA does not increase GLUT1 and CD98hc proteins. The increase in TfR1 does not result in higher anti-TfR1 antibody targetability, suggesting targeting sufficiently occurs with available transferrin receptors without further contribution from accessory VPA-induced TfR1.

Evapotranspiration is a critical component of the hydrological cycle, and it has a decisive impact on the ecosystem balance in arid and semi-arid regions. The Yinchuan Plain, located in the Gobi of Northwest China, has a strong surface ET. In order to assess the ET pattern in this region, we obtained the ETa of Yinchuan Plain between 1987 and 2020 using the GEE platform. We employed the Surface Energy Balance Model (SEBAL), specifically geeSEBAL, to analyze the change pattern of ET over different seasons, years, and land types. The results show that: ① In spring, the daily ETa of the Yinchuan Plain is highest in the central lake wetland area, with a maximum value of 4.32 mm day-1. In summer, it is concentrated around the croplands and water bodies, with a maximum value of 6.90 mm day-1; In Autumn and winter, it is mainly concentrated around the water bodies and impervious areas, with maximum values of 3.93 and 1.56 mm day-1, respectively. ② From 1987 to 2020, the ET of the Yinchuan Plain showed an obvious upward and downward trend in some areas with significant land use changes, but the overall ET of the region remained relatively stable without dramatic fluctuations. ③ The evapotranspiration of different underlying land use types in the Yinchuan Plain region is as follows: water body>cultivated land>impervious>grassland>bare land. Our results showed that geeSEBAL is highly applicable in the Yinchuan Plain area. It allows for the accurate and detailed inversion of ET in the study area, which facilitates the study of regional hydrological cycle and water governance.

YOLOv8, as an efficient object detection method, can swiftly and precisely identify objects within images. However, traditional algorithms encounter difficulties when detecting small targets in remote sensing images, such as missing information, background noise, and interactions among multiple objects in complex scenes, which may affect performance. To tackle these challenges, we propose an enhanced algorithm optimized for detecting small objects in remote sensing images, named HP-YOLOv8. Firstly, we design the C2f-D-Mixer (C2f-DM) module as a replacement for the original C2f module. This module integrates both local and global information, significantly improving the ability to detect features of small objects. Secondly, we introduce a feature fusion technique based on attention mechanisms, named Bi-Level Routing Attention in Gated Feature Pyramid Network (BGFPN). This technique utilizes an efficient feature aggregation network and reparameterization technology to optimize information interaction between different scale feature maps, and through the Bi-level Routing Attention (BRA) mechanism, it effectively captures critical feature information of small target objects. Finally, we propose the Smooth Mean Perpendicular Distance Intersection over Union (SMPDIoU) loss function. The method comprehensively considers the shape and size of detection boxes, enhances the model's focus on the attributes of detection boxes and provides a more accurate bounding box regression loss calculation method. To demonstrate our approach's efficacy, we conduct comprehensive experiments across the RSOD, NWPU VHR-10, and VisDrone2019 datasets. The experimental results show that the HP-YOLOv8 achieves 95.11%, 93.05%, and 53.49% in the [email protected] metric, and 72.03%, 65.37%, and 38.91% in the more stringent [email protected]:0.95 metric, respectively.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

Within environmental perception, automatic navigation and object detection, computer vision is a crucial and demanding field with many applications in modern industries, such as multi-target long-term visual tracking in automated production, defect detection, and driverless robotic vehicles with sensing ability. The performance of computer vision has greatly improved recently thanks to developments in deep learning algorithms and hardware computing capabilities, which has spawned the creation of a large number of related applications. This paper presents the results of a detailed review of over 50 papers published over the course of two decades (1999–2024), with a primary focus on the technical advancement of computer vision. To elucidate the foundational principles, an examination of typical visual algorithms based on traditional correlation filtering was initially conducted. Subsequently, a comprehensive overview of the most recent advancements in deep learning-based computer vision techniques was compiled. Furthermore, a comparative analysis between conventional and novel algorithms was undertaken to discuss the future trends and directions of computer vision. Lastly, the feasibility of employing visual SLAM (Simultaneous Localization and Mapping) algorithms in the context of autonomous vehicles with sensing capability was explored. Furthermore, we explored a thorough and efficient architecture for utilizing these techniques in autonomous robotic vehicles into unmanned green and low-carbon smart factories, underlining novel advances as well as potential prospects for future research.

Intermittent religious fasting increases a risk of hypo- and hyperglycemia in individuals with diabetes, but its impact in those without diabetes is poorly investigated. The study aim was to examine the effects of religious Bahá'í fasting (BF) on glycemic control and variability and compare these effects with time-restricted eating (TRE). In a three-arm randomized controlled trial, 16 subjects without diabetes were assigned to a BF, 16:8 TRE or control group. Continuous glucose monitoring and food intake documentation was conducted before and during the 19 days of intervention, and 24-hour mean glucose, glycemic variability indices, and glucotypes were assessed. BF and TRE groups, but not the control group, markedly reduced the daily eating window while maintaining macronutrient composition. Only the BF group decreased caloric intake (-677.8 ± 357.6 kcal, p=0.013), body weight (-1.92 ± 0.95 kg, p=0.011) and BMI (-0.65 ± 0.28 kg, p=0.006). Higher maximum glucose values were observed during BF in the within-group (+1.41 ± 1.04, p=0.039) and between-group comparison (BF vs. Control: p= 0.010 and TRE vs. BF: p= 0.022). However, there were no alterations of 24-hour mean glucose, intra- and inter-day glycemic variability indices, or glucotypes in any group. Proportions of time above and below range (70-180mg/dl) and HbA1c values remained unchanged. BF and TRE do not exhibit negative effects on glycemic control and variability in subjects without diabetes.

Global warming and the associated increasing frequency of heatwaves are on the rise leading to numerous health complications. Diabetic patients are more vulnerable to heat exposure than healthy individuals, owing to their impaired sweating ability, however, little is known about how heat exposure may impact the function of skin cells, commonly keratinocytes. Our recent report provided the first proof-of-concept revealing that the metabolic composition of sweat EVs is associated with metabolic changes in healthy individuals and type 2 diabetes patients. Given this and the shared cellular proprieties of eccrine sweat glands with keratinocytes, we questioned whether the metabolic changes in sweat EVs may mirror the responses of keratinocytes upon heat exposure. To this, we exposed HaCat, which were maintained in low (mimicking healthy condition) and high glucose (mimicking diabetes condition) to acute (90 min), chronic (48 h), and repetitive heat exposure at 40 ⁰C. Through conducting a set of experiments including a targeted metabolomics approach, Greiss assay, western blotting analysis, and electron microscopy studies. The data demonstrate that heat exposure results in substantial changes of metabolite levels belonging to amino acids, pyrimidine metabolism, and glycolysis pathways in high glucose maintained HaCat cells when compared to those noted in low glucose condition. Exploring the molecular mechanisms through which heat exposure may impact the metabolic composition in keratinocytes, our discoveries highlight nitric oxide (NO) as a novel biomarker that the level is correlated with heat duration and frequency. Furthermore, data reveal that the HSP-70 protein levels and mitochondrial morphology are consequently altered. This study provides evidence of shared metabolic alterations in keratinocytes and sweat EVs collected from clinical study and proposes, for the first time, NO as a novel biomarker for monitoring changes in health and diabetes upon heat exposure.

BACKGROUND This study investigated the association of postprandial plasma glucose (PPG) with cancer mortality using a general cohort of US adults. METHODS This cohort study included 14,860 US adults who attended the third National Health and Nutrition Examination Survey from 1988 to 1994, with mortality being followed up to December 31, 2019. The experimental exposures were levels of plasma glucose, including PPG with a fasting time of 0-3.9 h (PPG_0-3.9h) and 4-7.9 h (PPG_4-7.9h), plasma glucose with a fasting time ≥ 8 h (PG_fasting), and plasma glucose at 2 h after oral glucose tolerance test (PG_2hOGTT). Plasma glucose-associated cancer mortality risk was assessed using Cox proportional hazards models. RESULTS A 1-natural-log-unit increase in PPG_4-7.9h was associated with a higher multivariate-adjusted risk for cancer mortality [hazard ratio (HR), 3.24; 95% confidence interval (CI), 1.50-7.00]. However, PPG_0-3.9h, PG_fasting, PG_2hOGTT, hemoglobin A_1c, and insulin were not significantly associated with cancer mortality. The positive association of PPG_4-7.9h with cancer mortality remained in those without a prior diagnosis of cancer. CONCLUSIONS High PPG_4-7.9h is associated with a higher cancer mortality risk in US adults. Lowering PPG_4-7.9h may reduce cancer mortality.

Aim: Aging is companied by deteriorations of insulin resistance (IR) and insulin secretion. However, little is known about the roles of aging on different phases of insulin secretion (ISEC); i.e., the first- and second-phase of insulin secretion (FPIS, SPIS) and glucose effectiveness (GE). Methods: Totally 169 individuals (43 men and 126 women) with the similar fasting plasma glucose (FPG: 90 mg/dL) and BMI (men: 23 kg/m2, women 22 kg/m2) were enrolled. IR, FPIS, SPIS, and GE were estimated using our previously developed equations shown below. Pearson correlation analysis was conducted to assess the correlations between age and four diabetes factors (DFs: IR, FPIS, SPIS and GE). The equations that are used to calculate the DF in the present study were built and published by our group. Results: The age of the participants ranged from 18- to 78-year-old. Men had higher FPIS but lower HDL-C levels than women (2.067±0.159, 1.950±0.186 μU/min and 1.130±0.306, 1.348±0.357 mmol/dl, accordingly). The results of Pearson correlation revealed that age was negatively related to IR and GE in both genders (IR: r = -0.39, p < 0.001 for men, r = -0.24, p < 0.003 for women; GE: r = 0.66, p < 0.001 for men, r = 0.78, p < 0.001 for women). In the meanwhile, FPIS was also only found to be negatively correlated with age in female (r = -0.238, p = 0.003). But there was no different with SPIS and age in both of genders. Conclusions: We have found that in Chinese with normal FPG level (90 mg/dl) and body mass index (men: 23 kg/m2, women: 22: kg/m2), age is negatively related to IR and GE in both genders. At the same time, only FPIS was found to be negatively related to age in women. The tightness of their relationships, from the highest to the lowest are, GE, FPIS and IR accordingly. The importance of GE should be re-evaluated. These results should be interpreted with caution because of the small sample size.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Cascading landslides represent a dynamic and hazardous geological phenomenon, char-15 acterized by a sequential chain of slope failures triggered by various factors such as heavy rainfall, 16 seismic activity, or anthropogenic activities. These events can amplify the damage caused by the 17 initial trigger and propagate instability along a slope, often resulting in significant environmental 18 and societal impacts. The Morino-Rendinara cascading landslide, situated in the Ernici mountains 19 along the border of Abruzzo and Lazio region (Italy), serves as a notable example of the complexities 20 and devastating consequences associated with such events. In March 2021, a substantial debris flow 21 event in Morino obstructed the Liri River, marking the latest step in a series of landslide events 22 characterized by a complexity far beyond initial expectations. This study employs a multidiscipli-23 nary approach, combining conventional techniques and advanced technologies, to understand the 24 complexities of the Morino-Rendinara landslide. Field activities, UAV image acquisition, SAR inter-25 ferometry based on SENTINEL-1 images and pixel offset analysis based on high-resolution Google 26 Earth images, offer insights into the geological and hydrogeological setting of the unstable slope, 27 landslide geometry, mechanism and kinematics. To supplement the analysis a specific FEM slope 28 stability analyses is used to reconstruct the deep geometry of the system emphasizing the modula-29 tion action of groundwater flow to the slope stability

Determining precise boundaries and protective zones for historical and cultural objects enables their effective preservation. This is particularly crucial in the face of increasing tourism, urbanization, and natural disasters. Accurately defining boundaries and protective zones can aid in the planning of scientific research, archaeological excavations, and other studies aimed at exploring the history and cultural significance of these objects. The article presents the framework for establishing protective zones around historical and cultural heritage sites existing in Ukraine, using the example of the Citadel defensive complex located in Lviv (Ukraine). It proposes general and detailed conceptual models for the combined application of remote and non-invasive methods for investigating historical and cultural heritage sites. This conceptual article introduces the theory of integrating radar satellite imaging with ground-based georadar imaging. Additionally, it presents a software module that has been developed to analyze collected data on two-dimensional historical and cultural heritage objects, refine their boundaries, and establish protective zones around them.

As the fast growth of information technology (IT), the safety of image transmission and the storing of images are increasingly concerned. Traditional image encryption algorithms have certain limitations in transmission and security, so there is an urgent need for a secure and reliable image encryption algorithm. A universal compression sensing (CS) image encryption (IE) algorithm based on DNA-triploid mutation (DTM) is presented in this paper. Firstly, by using CS algorithm an image is compressed while obtaining a range of chaotic sequences by iteration of chaotic map. Then DNA sequences are generated by encoding the image, and based on the DTM, new mutant DNA sequences are generated according to specific rules. Next, the chaotic sequences are operated at the DNA level to do confusion and diffusion operations on the image to ensure the security of the data. At last, DNA decoding is carried out to obtain the compressed-encrypted image. Both simulation experiments and performance tests fully show that a high level of security and reliability of the proposed algorithm in protecting image privacy is achieved.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

The shift towards autonomous excavators in construction and mining is a significant leap towards enhancing operational efficiency and ensuring worker safety. However, it presents challenges such as the need for sophisticated decision-making and environmental perception due to complex terrains and diverse conditions. Our study introduces the E-GTN framework, a novel approach tailored for autonomous excavation that leverages advanced multisensor fusion and a custom-designed convolutional neural network to address these challenges. Results demonstrate that GridNet effectively processes grid data, enabling the reinforcement learning algorithm to make informed decisions, thereby ensuring efficient and intelligent autonomous excavator performance. The study concludes that the E-GTN framework offers a robust solution for the challenges in unmanned excavator operations, providing a valuable platform for future advancements in the field.

This paper presents the design and analysis of a novel 3-degree-of-freedom (3-DOF) parallel ma-nipulator equipped with self-sensing Ni-Ti (Nitinol) actuators. The manipulator's architecture and mechanical design are elucidated, emphasizing the integration of Nitinol actuators. The self-sensing technique implemented in a previous work was extended to a 20 mm actuator length, and the actuator was used to design the 3 DOF manipulator. Kinematic analyses were conducted to eval-uate the manipulator's performance under various operating conditions. A dynamic model was implemented for the dynamic dimensioning of the actuators, which work synergistically with a bias spring. The manipulator was realized, and a control strategy was implemented. Experimental tests, although documenting some positioning accuracy issues, show the efficacy and potential applica-tions of the proposed manipulator in robotics and automation systems, highlighting the advantages of self-sensing Nitinol actuators in small parallel manipulator designs.

Incorrect sitting posture, characterized by asymmetrical or uneven positioning of the body, often leads to spinal misalignment and muscle tone imbalance. Prolonged maintenance of such postures can adversely impact well-being and contribute to the development of spinal deformities and musculoskeletal disorders. In response, smart-sensing chairs equipped with cutting-edge sensor technologies have been introduced as a viable solution for real-time detection, classification, and monitoring of sitting postures, aiming to mitigate the risk of musculoskeletal disorders and promote overall health. This comprehensive literature review evaluates the current body of research on smart-sensing chairs, with a specific focus on the strategies used for posture detection and classification, as well as the effectiveness of different sensor technologies. A meticulous search across MDPI, IEEE, and Google Scholar databases yielded 34 pertinent studies that utilize non-invasive methods for posture monitoring. The analysis reveals that Force Sensing Resistors (FSR) are the predominant sensors utilized for posture detection, whereas Convolutional Neural Networks (CNN) and Artificial Neural Networks (ANN) are the leading machine learning models for posture classification. However, it was observed that CNNs and ANNs do not outperform traditional statistical models in terms of classification accuracy, due to constrained size and lack of diversity within training datasets. These datasets often fail to comprehensively represent the array of human body shapes and musculoskeletal configurations. Moreover, this review identifies a significant gap in the evaluation of user feedback mechanisms, essential for alerting users to their sitting posture and facilitating corrective adjustments.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

Pseudomonas aeruginosa is an opportunistic Gram-negative bacterium that remains a prevalent clinical and environmental challenge. Quorum sensing (QS) molecules are effective biomarkers in pinpointing the presence of P. aeruginosa. This study aimed to develop a convenient-to-use whole-cell biosensor using P. aeruginosa reporters individually encapsulated within alginate-poly-L-lysine (alginate-PLL) microbeads to specifically detect the presence of bacterial autoinducers. The PLL-reinforced microbeads were prepared using a two-step method involving ionic crosslinking and subsequent coating with thin layers of PLL. The alginate-PLL beads showed good stability in the presence of a known cation scavenger (sodium citrate), which typically limits the widespread applications of calcium alginate. In media containing synthetic autoinducers, such as N-(3-oxo dodecanoyl) homoserine lactone (3-oxo-C12-HSL) and N-butanoyl-L-homoserine lactone (C4-HSL) or cell-free supernatants of planktonic or flow cell biofilm effluent of wild P. aeruginosa (PAO1), the encapsulated bacteria enabled a dose-dependent detection of the presence of these QS molecules. The prepared bioreporter beads remained stable during prolonged storage at 4 and -80 °C and were ready for on-the-spot sensing without the need for recovery. This whole-cell biosensor demonstrates the practicality of the encapsulated bioreporter for bacterial detection based on specific QS molecules.

Chlorophyll-a (Chl-a), a proxy for phytoplankton biomass, is one of the few biological water quality indices detectable using satellite observations. However, models for estimating Chl-a from satellite signals are currently unavailable for many lakes. The application of Chl-a prediction algorithms may be affected by the variance in optical complexity within lakes. Using Lake Winnipeg in Canada as a case study, we demonstrated that separating models by the lake’s basins [north basin (NB) and south basin (SB)] can improve Chl-a predictions. By calibrating more than 40 commonly used Chl-a estimation models using Landsat data for Lake Winnipeg, we achieved higher correlations between in situ and predicted Chl-a when building models with separate Landsat-to-in-situ matchups from NB and SB (R² = 0.85 and 0.76, respectively; p &lt; 0.05), compared to using matchups from the entire lake (R² = 0.38, p &lt; 0.05). In the deeper, clearer waters of the NB, a green-to-blue band ratio provided better Chl-a predictions, while in the shallower, highly turbid SB, a red-to-green band ratio was more effective. Our approach can be used for rapid Chl-a modeling in large lakes using cloud-based platforms like Google Earth Engine with any available satellite or time series length.

The objective of image super-resolution is to reconstruct a high-resolution (HR) image with the prior knowledge from one or several low-resolution (LR) images. However, in the real world, due to the limited complementary information, the performance of both single-frame and multi-frame super-resolution reconstruction degrades rapidly as the magnification increases. In this paper, we propose a novel two-step image super resolution method concatenating multi-frame super-resolution (MFSR) with single-frame super-resolution (SFSR), to progressively upsample images to the desired resolution. The proposed method consisting of an L0-norm constrained reconstruction scheme and an enhanced residual back-projection network, integrating the flexibility of the variational model-based method and the feature learning capacity of the deep learning-based method. To verify the effectiveness of the proposed algorithm, extensive experiments with both simulated and real world sequences were implemented. The experimental results show that the proposed method yields superior performance in both objective and perceptual quality measurements, compared to the baseline super-resolution algorithms in the cascade model. In addition, the experiment indicates that this cascade model can be robustly applied to different SFSR and MFSR methods.

With the rapid developments that have been made in computer vision and computer technology, semantic segmentation of high-resolution images has emerged as a mainstream and challenging task. The, segmentation of water areas remains a complex task due to the similar features between water areas or between water areas and other land objects. Meanwhile, since coastlines and riverbanks are typically presented in irregular shapes, it is difficult to obtain the categories of pixels at boundaries. This paper proposed the use of a Water-Land Boundary Attention Network (WLBANet) to improve the accuracy of pixels at boundaries between water and land. This network also reinforced the performance of contextual information extraction into distinguishing between water areas and other land objects. To prove the validity of this proposed network, WLBANet was performed on the Water Land Dataset (WLD), which is also by this paper, and which contains water areas and other land objects categories. The results demonstrates that the proposed method has significant effectiveness.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

The relentless advancement and integration of mechanization and intelligence within the coal mining industry, combined with the increasing depths of mining operations, necessitate significantly higher safety standards. This necessity arises due to the increasingly complex geological and coal seam conditions encountered as mining operations delve deeper into the earth. Traditionally, 3D seismic exploration technology has been fundamental in ensuring both operational efficiency and safety in the coal mining sector. However, despite its critical role, this technology still has limitations in detecting and characterizing small-scale geological structures which can pose substantial risks if not accurately identified and mitigated. To address these challenges, this paper introduces a sparsity-constrained adaptive hard thresholding algorithm designed to tackle the spectral inversion optimization problem with an norm constraint for the enhanced retrieval of reflection coefficients, thereby establishing a comprehensive workflow for enhancing seismic data resolution through compressed sensing spectral inversion. Real data validation has demonstrated that this method significantly enhances the resolution of seismic data while maintaining the amplitude integrity and fidelity of the original signals. This improvement allows for a more detailed and accurate characterization of small-scale geological features, which are critical in identifying and mitigating potential hazards within coal mining operations, thus offering robust support for the implementation of more effective safety protocols and disaster prevention strategies in coal mines.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

Purpose: National Institute for Health and Care Excellence (NICE) has recently published quality standards for assessment of fall risk and preventing further falls. According to the standards, multifactorial fall risk assessments should include: identification of falls history; analysis of gait, balance, mobility and muscle strength, among other factors. Despite being based on subjective analysis or simple timing and not being multifactorial, physiotherapists and physicians quite often use these tests as reference scales to differentiate between lower and higher risk of falling. Instrumented TUG has been recently reported to provide important additional information to the overall score. Objective: To explore a case-based approach of fall risk assessment to identify the most relevant and informative risk factors that in combination could better define a person risk profile. Materials and Methods: A multifactorial assessment of fall risk through questionnaires, standard functional tests, tests instrumented with inertial sensors, and force platforms has been studied within a group aged 55-80 years old. Different fall risk factors and fall risk assessment methods were analyzed in a case-based descriptive study. Results & Discussion: Subjects at higher risk of falling were identified based on their detailed profiles. A set of features were obtained from the instrumented standard tests differing significantly between subjects presenting higher or lower fall risk. Therefore, instrumenting conventional tests with wearables containing inertial sensors and force platforms gives more detailed and quantitative insights. This information can be used to better define and tailor fall prevention exercises and to improve the follow-up of the evolution of the subject.

The cyclic AMP-responsive element-binding protein H (CREBH, encoded by CREB3L3) is a membrane-bound transcriptional factor that primarily localizes in the liver and small intestine. CREBH governs triglyceride metabolism in the liver, which mediates the changes in gene expression governing fatty acid oxidation, ketogenesis, and apolipoproteins upregulating LPL activity. A deficiency of CREBH in mice leads to severe hypertriglyceridemia. CREBH, in synergy with PPARα, has a crucial role in upregulating Fgf21 expression, which is implicated in metabolic homeostasis. CREBH binds to and functions as a co-activator for both PPARα and LXRα in regulating gene expression of lipid metabolism. Furthermore, intestinal CREBH in overexpression reduces cholesterol absorption and suppresses high-cholesterol diet-induced fatty liver. Conversely, a deficiency of CrebH in mice fed on various high-fat diets leads to severe fatty liver. Thus, CREBH could be a therapeutic target in the treatment of metabolic diseases.

This manuscript offers a concise overview of paper microfluidics, emphasizing its sustainable sensing applications in healthcare, environmental monitoring, and food safety. Researchers have developed innovative sensing platforms for detecting pathogens, pollutants, and contaminants by leveraging the paper’s unique properties, such as biodegradability and affordability. These portable, low-cost sensors facilitate rapid diagnostics and on-site analysis, making them invaluable tools for resource-limited settings. The review discusses fabrication techniques, principles, and applications of paper microfluidics, showcasing its potential to address pressing challenges and enhance human health and environmental sustainability.

Background: Diet is a risk factor for gestational diabetes mellitus (GDM). There are few studies on women´s diet and glucose tolerance test (GTT) results. Objective: To evaluate the relationship between previous diet and the number of abnormal values on the diagnostic GTT in women with GDM. We hypothesized there would be an inverse relation between antioxidant micronutrient consumption and the number of abnormal GTT values. Methods: This cross-sectional study included 60 women diagnosed with GDM (2-hours, 75g-GTT). Shortly after diagnosis, participants answered a validated food frequency questionnaire to assess food consumption in the last 6 months. Mann-Whitney´s test was used to compare the dietary intake of participants with one (group 1) versus two-three (group 2) abnormal GTT values. Results: Participant characteristics were similar. There were no significant differences between groups in median intake of total calories, carbohydrates, lipids and proteins. Participants in group 1 had significantly higher intakes of fiber (11.9 vs. 11.0 g/day p= 0.049), vitamin D (40.6 vs. 40.4 mcg/day p= 0.049) and vitamin C (180.0 vs. 151.0 mg/day p= 0.008) than those in group 2. Conclusion: Results suggest a possible association between consumption of fiber and some antioxidant micronutrients and GDM severity at the time of diagnosis.

Due to the rapid development of unmanned aerial vehicles (UAVs) communication technology, UAVs are gradually competing with primary users (PUs) for spectrum resources. Cognitive radio (CR) is a promising solution to meet the needs. Cooperative spectrum sensing (CSS) is considered as an effective method to detect the PU signal and identify available spectrum resources for UAVs in a cognitive UAV network (CUAVN). However, the cooperative mode among multiple UAVs may incur a high overhead, resulting in performance degradation. Therefore, we introduce a differential sequential 1 (DS1), which incorporates a differential mechanism and leverages the sequential idea based on the classical voting rule to enhance cooperative performance and efficiency. In view of this, we formulate three scenarios to characterize the PU activity and introduce a multi-slot cooperative mode within a single UAV to realize cooperative gain. Further, only the information change about the PU status is sequentially calculated in DS1, and combined with a sequential idea, the efficiency of the voting rule is greatly improved. Moreover, the application of support vector machines (SVM) in dynamic selection enables the selection of the most suitable voting rule based on diverse sensing parameters. This dynamic selection process ensures optimal performance and efficiency by adapting the voting rule to the specific characteristics of the given scenario. Finally, simulation results demonstrate that the superiority of our proposal with respect to the detection performance, sample size and the energy efficiency is evident, which proves the high performance of the proposed policy.

The radar sensor described realizes healthcare monitoring capable of detecting subject chest-wall movement caused by cardiopulmonary activities, and wirelessly estimating the respiration and heartbeat rates of the subject without attaching any devices to the body. Conventional single-tone Doppler radar can only capture Doppler signatures because of a lack of bandwidth information with noncontact sensors. In contrast, we take full advantage of impulse radio ultra-wideband (IR-UWB) radar to achieve low power consumption and convenient portability, with a flexible detection range and desirable accuracy. A noise reduction method based on improved ensemble empirical mode decomposition (EEMD) and a vital sign separation method based on the continuous-wavelet transform (CWT) are proposed jointly to improve the signal-to-noise ratio (SNR) in order to acquire accurate respiration and heartbeat rates. Experimental results illustrate that respiration and heartbeat signals can be extracted accurately under different conditions. This noncontact healthcare sensor system proves the commercial feasibility and considerable accessibility of using compact IR-UWB radar for emerging biomedical applications.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

The rapid advancements in satellite technology have led to a significant increase in high-resolution remote sensing (RS) images, necessitating advanced processing methods. Additionally, a patent analysis revealed a significant increase in deep learning and machine learning applications in remote sensing, highlighting the growing importance of these technologies. Therefore, this paper introduces the Kolmogorov-Arnold Network (KAN) model to remote sensing, aiming to enhance efficiency and performance in RS applications. We conducted several experiments to validate KAN's applicability, starting with the EuroSAT dataset, where we combined the KAN layer with multiple pretrained CNN models. The optimal performance was achieved with ConvNeXt, leading to the development of the KonvNeXt model. KonvNeXt was evaluated on the Optimal-31, AID, and Merced datasets for validation, and it achieved accuracies of 90.59%, 94.1%, and 98.1%, respectively. The model also showed fast processing speed, with the Optimal-31 and Merced datasets completed in 107.63 seconds each, while the bigger and more complicated AID dataset took 545.91 seconds. This result is meaningful since it achieved faster speeds and comparable accuracy compared to the existing study which utilized VIT and proved KonvNeXt's applicability for remote sensing classification tasks. Furthermore, we investigated the model's interpretability by utilizing Occlusion Sensitivity and by displaying the influential regions, it validated its potential use in a variety of domains including medical imaging and weather forecasting. This paper is meaningful in that it is the first use of KAN in remote sensing classification, proving its adaptability and efficiency.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

Ecological city is currently a hot topic in urban planning research. How to balance urban development and ecological environment protection has become a focus and difficulty of research. Traditional urban planning is mainly based on experience, but its disadvantage is that it is easy to overlook key geographical factors such as terrain and vegetation, and cannot fully reflect the actual spatial characteristics of the city. Therefore, this article applied the combination of urban and rural planning and environmental remote sensing technology to urban planning and design, obtaining a massive amount of data. Through the actual analysis of Langfang, this paper monitored the vegetation, water, land and landscape data of Langfang through environmental remote sensing technology. By using these data to identify existing problems, this article proposed reasonable planning for the problems, in order to achieve the effective goal of ecological city planning and design. It provided a more accurate analysis of urban structure, including urban planning and urban ecological landscape planning. Among them, ecological landscape planning includes renovating ecological embankments, protecting ecological green belts around the city, and creating characteristic landscape areas, thereby providing more scientific basis for urban planning and design, making urban planning and design more reasonable and scientific. This paper investigated the planned Langfang City, and the average errors of vegetation, soil, water quality, and landscape data obtained from traditional field surveys were 0.35, 0.33, 0.34, and 0.31, respectively. The average errors of remote sensing technology in obtaining vegetation, soil, water quality, and landscape data were 0.16, 0.15, 0.17, and 0.15, respectively. The total suspended solids content of waterscape 1-10 before planning was 5.51mg/L and 7.41mg/L, respectively. After planning, the total suspended solids content of waterscape 1-10 was 3.60mg/L and 4.47mg/L, respectively. From this, it can be seen that the error in obtaining data after planning has decreased, and the total suspended solids content has also decreased.

The objective of this pilot study was to compare glucose concentrations in capillary blood (CB) samples analysed in a laboratory by a validated method and glucose concentrations measured in the interstitial fluid (ISF) by continuous glucose monitoring under different physical activity levels in a postprandial state in healthy and active subjects without diabetes. Ten healthy, active subjects (26±4 years, 67±11 kg bodyweight (BW), 11±3 h) were included in the study. Within 14 days, they underwent six tests consisting of a) resting fasted (R/Fast), b) resting after intake of 1 g glucose/kg BW (R/Glc) and c) running for 60 minutes at moderate (65/Glc) and d) high (85/Glc) intensity after intake of 1 g glucose/kg BW. Data were collected in the morning, following a standardised dinner before test day. Sensor-based glucose concentrations were compared to simultaneous capillary blood glucose concentrations. Pearson’s r correlation coefficient was highest for R/Glc (.92, p<.001) compared to R/Fast (.45, p<.001), 65/Glc (.60, p<.001) and 85/Glc (.70, p<.001). Mean absolute relative deviation (MARD) and standard deviation (SD) was smallest for resting fasted and similar between all other conditions (R/Fast: 8±6%, R/Glc: 17±12%, 65/Glc: 22 ± 24%, 85/Glc: 18±17%). However, Bland-Altman plot analysis showed a higher range between lower and upper limits of agreement (95% confidence interval) of paired data under exercising compared to resting conditions. Under resting fasted conditions, both methods produce similar outcomes. Under resting postprandial and exercising conditions, respectively, there are differences between both methods. However, further data in healthy subjects need to be gathered considering physical activity and nutrition status.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

In this work, an enzymatic sensor, based on a bionanocomposite film consisting of a polyelectrolyte complex (PEC) [Chitosan/kappa-carrageenan] doped with gold nanoparticles (AuNPs) encapsulating glucose oxidase (GOD) deposited on a gold electrode (Au) for glucose sensing, is described. Using the electrocatalytic synergy of AuNPs and GOD as a model of enzyme, the variation of the current (µA) as a function of the log of the glucose concentration (log [glucose]), shows 3 times higher sensitivity for the modified electrode (283.9) compared to that of the PEC/GOD modified electrode (93.7), with a detection limit of about 5 µM and a linearity range between 10µM and 7mM. The response of the PEC/AuNPs/GOD based biosensor also presents good reproducibility, stability and negligible interfering effects from ascorbic acid, uric acid, urea and creatinine. The applicability of the PEC/AuNPs/GOD based biosensor was tested in glucose-spiked saliva samples and acceptable recovery rates were obtained.

Background/Objectives: The global burden of metabolic dysfunction-associated steatotic liver disease (MASLD) is increasing at an alarming rate. Cardiovascular disease (CVD) is the leading cause of mortality in MASLD patients, therefore, the therapeutic interventions for MASLD should improve coronary risk factors such as obesity, diabetes and dyslipidemia, in addition to improving liver function. The evidence on effect of sodium-glucose cotransporter 2 inhibitors (SGLT2is) which have beneficial pharmacological properties for MASLD, especially the long-term effects, on the progression of MASLD in Asian population is very limited. Methods: The retrospective longitudinal study was performed by using the medical records at the National Center for Global Health and Medicine, Kohnodai Hospital, Japan. We picked up patients with type 2 diabetes who had taken SGLT2is for at least 3 years or longer between April 1, 2014 and March 31, 2018. We collected the data on metabolic parameters, including blood tests and anthropometric parameters, and compared the data before and after the initiation of SGLT2is treatment. Results: During the observation period, 324 patients had taken SGLT2is for 3 years. The 3-year-SGLT2is treatment significantly reduced body weight, hemoglobin A1c, low-density lipoprotein-cholesterol, triglyceride and non-high-density lipoprotein-cholesterol (HDL-C) and significantly increased HDL-C. Furthermore, this treatment significantly improved liver function and the markers for hepatic steatosis and hepatic fibrosis. Conclusions: Considering that the development of CVD determines the prognosis of MASLD patients, the long-term SGLT2is treatment may be an ideal therapy for MASLD patients.

Oncolytic virotherapy is a promising immunotherapy approach for cancer treatment, utilizing viruses to preferentially infect and eliminate cancer cells while stimulating immune responses. In this review we synthesize current literature on the molecular circuits of immune sensing and response to oncolytic virotherapy; focusing on viral DNA or RNA sensing by infected cells, cytokine and danger-associated signal sensing by neighboring cells, and subsequent downstream activation of immune pathways. The sequential sense-and-response mechanisms involve the triggering of molecular sensors by viruses or infected cells to activate transcription factors and related genes for a breadth of immune responses. We describe how molecular signals induced in the tumor upon virotherapy can trigger diverse immune signaling pathways, activating both antigen-presenting cell-based innate and T cell-based adaptive immune responses. Insights into these complex mechanisms provide valuable knowledge for enhancing oncolytic virotherapy strategies.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Rho guanosine triphosphatases (GTPases) are key regulators in a number of cellular functions, including actin cytoskeleton remodeling and vesicle traffic. Traditionally, Rho GTPases are studied because of their function in cell migration and cancer, while their roles in metabolism are less documented. However, emerging evidence implicates Rho GTPases as regulators of processes of crucial importance for maintaining metabolic homeostasis. Thus, the time is now ripe for reviewing Rho GTPases in the context of metabolic health. Rho GTPase-mediated key processes include the release of insulin from pancreatic β-cells, glucose uptake into skeletal muscle and adipose tissue, and muscle mass regulation. Through the current review, we cast light on the important role of Rho GTPases in skeletal muscle, adipose tissue, and the pancreas and mechanisms by which Rho GTPases act to regulate glucose metabolism in health and disease. We also describe challenges and goals for future research.

Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.

Flooding, exacerbated by climate change, poses a significant threat to certain areas, increasing in frequency and severity. In response, the construction of supplementary dams has emerged as a reliable solution for flood management. This study employs a Remote Sensing (RS) approach integrated with GIS to assess the feasibility of constructing a supplementary dam near Linville, Brisbane, Australia, with the aim of mit-igating floods and preventing overtopping failure at the Wivenhoe Dam. Using QGIS software and a 25-meter resolution DEM from the Queensland Spatial Catalogue ‘QSpatial’ website, four potential dam sites were analysed, considering cross-sections, watershed characteristics, and water volume calculations. Systematic selection criteria were applied to identify the most optimal option based on dam wall di-mensions, volume-to-area, and volume-to-cost ratios. The selected option was further assessed against predefined criteria, yielding one optimal choice. The study provides insights into the feasibility and ef-fectiveness of supplementary dam construction for flood mitigation in the region, with recommendations for future research and implementation.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r&gt;0.90) and peri-urban (HWM, HWA, r&gt;0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Microcystis-dominated cyanobacterial blooms (MCBs) frequently occur in freshwaters worldwide due to massive Microcystis colonies formation and severely threaten human and ecosystems health. Quorum sensing (QS) is a direct cause of Microcystis colonies formation, possibly regulating MCBs occur and Microcystis population behaviors [1, 2]. Many novel findings in fundamental knowledge of Microcystis QS phenomenon and the signaling molecules have been documented. However, little effort has devoted to comprehensively summarize and discuss research progresses and exploration direction on QS signaling molecules-mediated QS system in Microcystis. This article summarizes action process of N-acyl homoserine lactones (AHLs) as major signaling molecules in Microcystis and discussed the detailed roles of AHLs-mediated QS system in cells aggregation, colonies formation, ecological adaptability and competitive advantage. And the progress was summarized in research on the QS mechanism in Microcystis. Compared to other QS system, the LuxI/LuxR-type QS system is more likely to found in Microcystis. Also, we introduced Quorum quenching (QQ) — QS blocking process in Microcystis, with emphasizing on the potential of QS inhibitors in MCBs control. Finally, in response to the research deficiencies and gaps in Microcystis QS and QQ, we proposed several future research directions in these fields. This review may deepen the understanding of Microcystis QS knowledge and provide theoretical guidance for the development of strategies to monitor, control and harness MCBs.

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

Understanding the distribution of rock glaciers provides key information for investigating and recognizing the status and changes of the periglacial environment. Deep learning algorithms and red-green-blue (RGB) bands from high-resolution satellite images have been extensively employed to map rock glaciers. However, the near-infrared (NIR) band offers rich spectral information and sharp edge features that could significantly contribute to semantic segmentation tasks, but it is rarely utilized in constructing rock glacier identification models due to the limitation of three input bands for classical semantic segmentation networks, like DeeplabV3+. In this study, a dual-encoder DeeplabV3+ network (DEDNet) was designed to overcome the flaws of classical DeeplabV3+ network (CDNet) when identifying rock glaciers using multispectral remote sensing images by extracting spatial and spectral features from RGB and NIR bands, respectively. This network, trained with manually labeled rock glacier samples from QiLian Mountains, established a model with accuracy, precision, recall, specificity, and mIoU (Mean Intersection over Union) of 0.9131, 0.9130, 0.9270, 0.9195, and 0.8601, respectively. The well-trained model was applied to identify new rock glaciers in a test region, achieving a producer's accuracy of 93.68% and a user's accuracy of 94.18%. Furthermore, the model was employed to two study areas in northern Tien Shan (Kazakhstan) and Daxue Shan (Hengduan Shan, China) with high accuracy, which proved that the DEDNet offers an innovative solution to more accurately map rock glaciers on a larger scale due to its robustness across diverse geographic regions.

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. The focus of this study was to estimate and thematically map on a pixel-by-pixel basis, the actual evapotranspiration (ET_a) of the Wonji Shoa Sugarcane Estate using the Surface Energy Balance Algorithm for Land (SEBAL), Simplified Surface Energy Balance (SSEB) and Operational Simplified Surface Energy Balance (SSEBop) algorithms. The results obtained revealed that the ranges of the daily ETa estimated on January 25, February 26, September 06 and October 08, 2002 using SEBAL were 0.0 - 6.85, 0.0 – 9.36, 0.0 – 3.61, 0.0 – 6.83 mm/day; using SSEB 0.0 - 6.78, 0.0 – 7.81, 0.0 – 3.65, 0.0 – 6.46 mm/day, and SSEBop were 0.05 - 8.25, 0.0 – 8.82, 0.2 – 4.0, 0.0 – 7.40 mm/day, respectively. The Root Mean Square Error (RMSE) values between SSEB and SEBAL, SSEBop and SEBAL, and SSEB and SSEBop were 0.548, 0.548, and 0.99 for January 25, 2002; 0.739, 0.753, and 0.994 for February 26, 2002;0.847, 0.846, and 0.999 for September 06, 2002; 0.573, 0.573, and 1.00 for October 08, 2002, respectively. The standard deviation of ET_a over the sugarcane estate showed high spatio-temporal variability perhaps due to soil moisture variability and surface cover. The three algorithm results showed that well watered sugarcane fields in the mid-season growing stage of the crop had higher ET_a values compared with the other dry agricultural fields confirming that they consumptively use more water. Generally during the dry season, ET_a is limited to water surplus areas only and in wet season, ET_a was high throughout the entire sugarcane estate. The evaporation fraction (ETrF) results also followed the same pattern as the daily ET_a over the sugarcane estate. The total crop and irrigation water requirement and effective rainfall estimated using the Cropwat model were 2468.8, 2061.6 and 423.8 mm/yr for January 2001 planted and 2281.9, 1851.0 and 437.8 mm/yr for March 2001 planted sugarcanes, respectively. The mean annual ET_a estimated for the whole estate were 107 Mm³, 140 Mm³, and 178 Mm³ using SEBAL, SSEB, and SSEBop, respectively. Even though the algorithms should be validated through field observation, they have potential to be used for effective estimation of ET in the sugarcane estate.