Non-enzymatic glucose sensing is a crucial field of study because of the current market demand. This study proposes a novel design of glucose sensor with enhanced selectivity and sensitivity by using graphene Schottky diodes, which is composed of Graphene/Platinum Oxide/n-Silicon heterostructure. The sensor was tested with different glucose concentrations and interfering solutions to investigate its sensitivity and selectivity. Different structures of the device were studied by adjusting the platinum oxide film thickness to investigate its catalytic activity. It was found that the film thickness plays a significant role in the efficiency of glucose oxidation and hence in overall device sensitivity. Moreover, theoretical investigations were conducted using Density Function Theory (DFT) to better understand the detection method and the origins of selectivity. The working principle of the sensors puts it in a competitive position with other non-enzymatic glucose sensors. DFT calculations provided a qualitative explanation of the charges distributed across the graphene sheet within a system of a platinum substrate with D-glucose molecules above. The proposed graphene/PtO/n-Si heterostructure has proven to satisfy these factors, which opens the door for further developments of more reliable non-enzymatic glucometers for continuous glucose monitoring systems.

Various efforts have been made to detect minimum value of glucose in any medium like water or body buffer solutions with high-sensitivity, accurate, and low-cost sensors in order to enhance life style. Therefore, the present study was done to investigate reliability of two-dimensional plasmonic structure by circular dichroism (CD) and ellipsometry tools in different concentrations of glucose. Our results confirmed a dependency of the CD signal on glucose concentrations and also a very good sensitivity based on the phase difference between each polarization in ellipsometry parameters with the help of an achiral plasmonic structure.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

The integration of metal nanoparticles and solid carriers can achieve ideal stability, high load and good conductivity. In this work, copper nanoparticles (Cu NPs) were sequentially deposited on a cobalt metal-organic framework (Co-MOF) by bonding with exposed imino groups, followed by a reduction reaction to prepare a new Cu@Co-MOF composite. Cu@Co-MOF acts as a non-enzymatic electrochemical sensor to detect glucose (Glu) in an alkaline medium. The composite working electrode of Cu@Co-MOF/GCE (GCE = glassy carbon electrode) improves the electrocatalytic activity for Glu oxidation. Cu@Co-MOF/GCE shows excellent electrocatalytic performances in Glu concentration ranging 0.005~1.8 mmol∙L⁻¹ (mM): the sensitivities are 282.89 μA∙mM⁻¹∙cm⁻² in 0.005-0.4 mM Glu and 113.15 μA∙mM⁻¹∙cm⁻² in 0.4-1.8 mM Glu respectively with low detection limit of 1.6 μM (S/N = 3) and high selectivity and stability.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Background: Several kinds of research say that adjuvant blood glucose and blood pressure are usual, but an efficient solution for medical application count remains. This review analyzes the pandemic blood pressure and blood glucose to identify the publications which tell about the clinical practices and research gaps in systematic research.Methods: A study guides to identify the research of Blood Pressure (BP) and Blood Glucose. In order to analyze the recent innovations and research on BP and Blood glucose, the relevant publications and literature from journals were identified.Results: Co-morbidity of BP and Blood glucose is reported as very high. The commonness of blood pressure is thrice as high in type I diabetes patients and almost two times higher in type II diabetes patients when compared to others without Diabetes. The pervasiveness of getting depression is more in the female when compared with men. A detailed study about the linkage of BP and blood glucose tells that the relationship between them is not exactly clear.Limitations: Nearly all reviews providing the linkage of BP and blood glucose are with some limitations and they are not providing any clear conclusion.Conclusions: Present research tells that people having high blood glucose will have a greater chance of getting high blood pressure. More research is needed to state the linkage between BP, blood glucose, and the growth of diabetes mellitus issues and to provide support for managing Diabetes.

Prediabetes is a significant risk factor for the development of Type 2 diabetes, cardiovascular diseases, chronic kidney disease, and other complications. Early diagnosis of prediabetes, coupled with education on lifestyle changes that support blood glucose management, are crucial for the prevention or delay of type 2 diabetes and related complications. This study aimed to examine the effects of individualized nutrition therapy (INT) combined with continuous glucose monitoring (CGM) on blood glucose control in individuals with prediabetes who are overweight or obesese. Participants (mean age ± SD: 55 ± 6 years; BMI: 31.1 ± 4.1 kg/m²) were randomly assigned to either the treatment group (n = 15) or the control group (n = 15). Both groups received INT and CGM, but the control group was blinded to the CGM data until the end of the study. Participants were followed for 30 days and visited the lab every 10 days for CGM replacement, study measurements, and dietary consultations. The treatment group showed a significant increase in the percent of time in the target blood glucose range (p=0.02) and a significant decrease in mean blood glucose concentration (p<0.05), glucose management indicator (p=0.02), percent coefficient of variation for blood glucose (p=0.01), and the percent time spent in the high or very high blood glucose ranges (p= 0.04). These changes were not statistically significant for the control group. We conclude that adding CGM feedback to INT resulted in better management of blood glucose levels in overweight or obese individuals with prediabetes.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

We have designed cell penetrating peptides that target the leucine zipper transcription factors ATF5, CE-BPB and CEBPD and that promote apoptotic death of a wide range of cancer cell types, but not normal cells, in vitro and in vivo. While such peptides have the potential for clinical application, their mechanisms of action are not fully understood. Here, we show that one such peptide, Dpep, compromises glucose uptake and glycolysis in a cell-context-dependent manner (in about 2/3 of cancer lines assessed). These actions are dependent on induction of tumor suppressor TXNIP (thioredoxin interacting protein) mRNA and protein. Knockdown studies show that TXNIP significantly contributes to apoptotic death in those cancer cells in which it is induced by Dpep. The metabolic actions of Dpep on glycolysis led us to explore combinations of Dpep with clinically approved drugs metformin and atovaquone that inhibit oxidative phosphorylation and that are in trials for cancer treatment. Dpep showed additive to synergistic activities in all lines tested. In summary, we find that Dpep induces TXNIP in a cell-context-dependent manner that in turn sup-presses glucose uptake and glycolysis and contributes to apoptotic death of a range of cancer cells.

The GLUT members belong to a family of glucose transporter proteins that facilitate glucose transport across the cell membrane. The mammalian GLUT family consists of thirteen members (GLUTs 1-12 and HMIT). Humans have a recently duplicated GLUT member, GLUT14. Avians express the majority of GLUT members. The arrangement of multiple GLUTs across all somatic tissues signifies the important role of glucose across all organisms. Defects in glucose transport have been linked to metabolic disorders, insulin resistance and diabetes. Despite the essential importance of these transporters, our knowledge regarding GLUT members in avians is fragmented. It has been clear that there are no chicken orthologs of mammalian GLUT4 and GLUT7. Our examination of GLUT members in the chicken revealed that some chicken GLUT members do not have corresponding orthologs in mammals. We review the information regarding GLUT orthologs and their function and expression in mammals and birds, with emphasis on chickens and humans.

The importance of bio robotics has been increasing day by day. Researchers are trying to mimic nature in a more creative way so that, the system can easily adopt the complex nature and its environment. Hence, bio robotic gripper plays a role in physical connection between the environment and bio robotics system. While handling the physical world in biorobots gripper, the complexity occurs in feedback system where sensor plays a vital role. Therefore, human centered gripper sensor has a good impact on bio robotics field. But categorical classification and their selection process is not very systematic. This review paper follows PRISMA methodology to summarize the previous works on bio robotics gripper sensor and its selection process.. This paper discusses challenges in soft robotics systems, and the importance of sensing systems to facilitate critical control mechanisms along with their selection considerations. Furthermore, a classification of soft actuation based on gripper has been introduced. Moreover, some unique characteristics for soft robotics sensor are explored namely compliance, flexibility, multifunctionality, sensor nature, surface properties, and material requirements. In addition, a categorization of sensors for soft robotic gripper in terms of modalities has been established ranging from the tactile and force sensor to slippage sensor. Various tactile sensors ranging from piezoelectric sensing to optical sensing are explored as it has utmost importance in soft gripper to effectively address the increasing requirements for intelligence and automation. Finally, taking everything into consideration, a flow diagram has been suggested for selecting sensors specific to soft robotics applications.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

Plastic contamination of small dimensions (

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

Background. Transferrin receptor 1 (TfR1), glucose transporter 1 (GLUT1), and CD98hc are candidates for targeted therapy at the blood-brain barrier (BBB). Our objective was to challenge the expression of TfR1, GLUT1, and CD98hc in brain capillaries by the histone deacetylase inhibitor (HDACi) valproic acid (VPA). Methods. Primary mouse brain capillary endothelial cells (BCECs) and brain capillaries isolated from mice injected intraperitoneally with VPA were examined using RT-qPCR and ELISA. Targeting to the BBB was performed by injecting monoclonal anti-TfR1 (Ri7217)-conjugated gold nanoparticles measured using ICP-MS. Results. In BCECs co-cultured with glial cells, Tfrc mRNA expression was significantly higher after 6 h VPA returning to baseline after 24 h. In vivo Glut1 mRNA expression was significantly higher in males, but not females', receiving VPA, whereas Cd98hc mRNA expression was unaffected by VPA. TfR1 increased significantly in vivo after VPA, whereas GLUT1 and CD98hc were unchanged. Uptake of anti-TfR1-conjugated nanoparticles was unaltered by VPA in spite upregulated TfR expression. Conclusions. VPA upregulates TfR1 in brain endothelium in vivo and in vitro. VPA does not increase GLUT1 and CD98hc proteins. The increase in TfR1 does not result in higher anti-TfR1 antibody targetability, suggesting targeting sufficiently occurs with available transferrin receptors without further contribution from accessory VPA-induced TfR1.

BACKGROUND This study investigated the association of postprandial plasma glucose (PPG) with cancer mortality using a general cohort of US adults. METHODS This cohort study included 14,860 US adults who attended the third National Health and Nutrition Examination Survey from 1988 to 1994, with mortality being followed up to December 31, 2019. The experimental exposures were levels of plasma glucose, including PPG with a fasting time of 0-3.9 h (PPG_0-3.9h) and 4-7.9 h (PPG_4-7.9h), plasma glucose with a fasting time ≥ 8 h (PG_fasting), and plasma glucose at 2 h after oral glucose tolerance test (PG_2hOGTT). Plasma glucose-associated cancer mortality risk was assessed using Cox proportional hazards models. RESULTS A 1-natural-log-unit increase in PPG_4-7.9h was associated with a higher multivariate-adjusted risk for cancer mortality [hazard ratio (HR), 3.24; 95% confidence interval (CI), 1.50-7.00]. However, PPG_0-3.9h, PG_fasting, PG_2hOGTT, hemoglobin A_1c, and insulin were not significantly associated with cancer mortality. The positive association of PPG_4-7.9h with cancer mortality remained in those without a prior diagnosis of cancer. CONCLUSIONS High PPG_4-7.9h is associated with a higher cancer mortality risk in US adults. Lowering PPG_4-7.9h may reduce cancer mortality.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

Aim: Aging is companied by deteriorations of insulin resistance (IR) and insulin secretion. However, little is known about the roles of aging on different phases of insulin secretion (ISEC); i.e., the first- and second-phase of insulin secretion (FPIS, SPIS) and glucose effectiveness (GE). Methods: Totally 169 individuals (43 men and 126 women) with the similar fasting plasma glucose (FPG: 90 mg/dL) and BMI (men: 23 kg/m2, women 22 kg/m2) were enrolled. IR, FPIS, SPIS, and GE were estimated using our previously developed equations shown below. Pearson correlation analysis was conducted to assess the correlations between age and four diabetes factors (DFs: IR, FPIS, SPIS and GE). The equations that are used to calculate the DF in the present study were built and published by our group. Results: The age of the participants ranged from 18- to 78-year-old. Men had higher FPIS but lower HDL-C levels than women (2.067±0.159, 1.950±0.186 μU/min and 1.130±0.306, 1.348±0.357 mmol/dl, accordingly). The results of Pearson correlation revealed that age was negatively related to IR and GE in both genders (IR: r = -0.39, p < 0.001 for men, r = -0.24, p < 0.003 for women; GE: r = 0.66, p < 0.001 for men, r = 0.78, p < 0.001 for women). In the meanwhile, FPIS was also only found to be negatively correlated with age in female (r = -0.238, p = 0.003). But there was no different with SPIS and age in both of genders. Conclusions: We have found that in Chinese with normal FPG level (90 mg/dl) and body mass index (men: 23 kg/m2, women: 22: kg/m2), age is negatively related to IR and GE in both genders. At the same time, only FPIS was found to be negatively related to age in women. The tightness of their relationships, from the highest to the lowest are, GE, FPIS and IR accordingly. The importance of GE should be re-evaluated. These results should be interpreted with caution because of the small sample size.

Intermittent religious fasting increases a risk of hypo- and hyperglycemia in individuals with diabetes, but its impact in those without diabetes is poorly investigated. The study aim was to examine the effects of religious Bahá'í fasting (BF) on glycemic control and variability and compare these effects with time-restricted eating (TRE). In a three-arm randomized controlled trial, 16 subjects without diabetes were assigned to a BF, 16:8 TRE or control group. Continuous glucose monitoring and food intake documentation was conducted before and during the 19 days of intervention, and 24-hour mean glucose, glycemic variability indices, and glucotypes were assessed. BF and TRE groups, but not the control group, markedly reduced the daily eating window while maintaining macronutrient composition. Only the BF group decreased caloric intake (-677.8 ± 357.6 kcal, p=0.013), body weight (-1.92 ± 0.95 kg, p=0.011) and BMI (-0.65 ± 0.28 kg, p=0.006). Higher maximum glucose values were observed during BF in the within-group (+1.41 ± 1.04, p=0.039) and between-group comparison (BF vs. Control: p= 0.010 and TRE vs. BF: p= 0.022). However, there were no alterations of 24-hour mean glucose, intra- and inter-day glycemic variability indices, or glucotypes in any group. Proportions of time above and below range (70-180mg/dl) and HbA1c values remained unchanged. BF and TRE do not exhibit negative effects on glycemic control and variability in subjects without diabetes.

Global warming and the associated increasing frequency of heatwaves are on the rise leading to numerous health complications. Diabetic patients are more vulnerable to heat exposure than healthy individuals, owing to their impaired sweating ability, however, little is known about how heat exposure may impact the function of skin cells, commonly keratinocytes. Our recent report provided the first proof-of-concept revealing that the metabolic composition of sweat EVs is associated with metabolic changes in healthy individuals and type 2 diabetes patients. Given this and the shared cellular proprieties of eccrine sweat glands with keratinocytes, we questioned whether the metabolic changes in sweat EVs may mirror the responses of keratinocytes upon heat exposure. To this, we exposed HaCat, which were maintained in low (mimicking healthy condition) and high glucose (mimicking diabetes condition) to acute (90 min), chronic (48 h), and repetitive heat exposure at 40 ⁰C. Through conducting a set of experiments including a targeted metabolomics approach, Greiss assay, western blotting analysis, and electron microscopy studies. The data demonstrate that heat exposure results in substantial changes of metabolite levels belonging to amino acids, pyrimidine metabolism, and glycolysis pathways in high glucose maintained HaCat cells when compared to those noted in low glucose condition. Exploring the molecular mechanisms through which heat exposure may impact the metabolic composition in keratinocytes, our discoveries highlight nitric oxide (NO) as a novel biomarker that the level is correlated with heat duration and frequency. Furthermore, data reveal that the HSP-70 protein levels and mitochondrial morphology are consequently altered. This study provides evidence of shared metabolic alterations in keratinocytes and sweat EVs collected from clinical study and proposes, for the first time, NO as a novel biomarker for monitoring changes in health and diabetes upon heat exposure.

In this paper, a seamless connection between sensor technology and machine learning (ML) has been presented which has wide applicability in rehabilitation and physical medicine. The intent is to identify an ML algorithm which has a better performance, easy to deploy, and has less training time and consumes less computational resources. In short, we propose an algorithm which maximizes the synergy between a sensor and ML by maximizing classification performance and easy to do implementation, which is robust in computational power and lower in resource consumption. The premise of the work is to show the important considerations for evaluating ML algorithms for Upper-limb activity recognition for Physical medicine and rehabilitation field.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

The emerging wireless energy transfer technology enables sensor nodes to maintain perpetual operation. However, maximizing the network performance while preserving short charging delay is a great challenge. In this work, a Wireless Mobile Charger (WMC) and a Directional Charger (DC) are deployed to transmit wireless energy to the sensor node to improve the network's throughput. To the best of our knowledge, this is the first work to optimize the data sensing rate and charging delay by joint scheduling of MC and DC. We prove we can transmit maximum energy to each sensor node to obtain our optimization objective. In our proposed work, a DC selects a total horizon of equipped with DCs, which selects the horizon of each specific area with based on its antenna orientation. DC's orientation is scheduled for each time slot. Furthermore, multiple MCs are used to transmit energy for sensor nodes which cannot be covered by DCs. We divided the Rechargeable Wireless Sensor Network into several zones via the Voronoi diagram. We deployed a static DC and one MC charging location in each zone to provide wireless charging service jointly. We obtain the optimal charging location of MCs in each zone by solving Mix Integral Programming for energy transmission. The optimization objective of our proposed research is to sense maximum data from each sensor node with the help of maximum energy. The lifetime of each sensor network can increase, and the end delay can be maximized with joint energy transmission. Extensive simulation results demonstrate that our RWSNs are designed significantly to improve network lifetime over the baseline method.

Mobile health technologies enable continuous, quantitative assessment of mobility and gait in real-world environments, facilitating early diagnosis of gait disorders, disease progression monitoring, and prediction of adverse events like falls. Traditionally, mobile gait assessment predominantly relied on body-fixed sensors positioned at the feet or lower trunk. Here, we investigate the potential of an algorithm utilizing an ear-worn motion sensor for spatiotemporal segmentation of gait patterns. We collected 3D acceleration profiles from the ear-worn sensor during varied walking speeds in 53 healthy adults. Temporal convolutional networks were trained to detect stepping sequences and predict spatial relations between steps. The resulting algorithm, mEar, accurately detects initial and final ground contacts (F1 score of 99% and 91%, respectively). It enables determination of temporal and spatial gait cycle characteristics (among others stride time and stride length) with good to excellent validity at a precision sufficient to monitor clinically relevant changes in walking speed, stride-to-stride variability, and side asymmetry. This study highlights the ear as a viable site for monitoring gait and proposes its potential integration with in-ear vital sign monitoring. Such integration offers a practical approach to comprehensive health monitoring and telemedical applications, by integrating multiple sensors in a single anatomical location.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

The development of a rapid, sensitive, specific method for detecting foodborne pathogens is paramount in supplying safe food to enhance public health safety. Despite the significant improvement in pathogen detection methods, key issues are still associated with rapid methods, such as distinguishing living cells from dead, pathogenic potential or health risk of the analyte at the time of consumption, detection limit, and sample-to-result. The mammalian cell-based assays analyze pathogens' interaction with the host cells and are responsive to only live pathogens or active toxins. In this study, a human embryonic kidney (HEK293) cell line expressing Toll-Like Receptor 5 (TLR-5) and chromogenic reporter system (HEK dual hTLR5) was used for the detection of viable Salmonella in a 96-well tissue culture plate. This cell line responds to low concentrations of TLR5 agonist flagellin. Stimulation of TLR5 ligand activates nuclear factor-kB (NF-κB) - linked alkaline phosphatase (AP-1) signaling cascade inducing the production of secreted embryonic alkaline phosphatase (SEAP). With the addition of a ρ-nitrophenyl phosphate as a substrate, a colored end product representing a positive signal is quantified. The assay's specificity was validated with the top 20 Salmonella enterica serovars and 19 non-Salmonella spp. The performance of the assay was also validated with spiked food samples. The total detection time (sample-to-result), including shortened pre-enrichment (4 h) and selective enrichment (4 h) steps with artificially inoculated outbreak-implicated food samples (chicken, peanut kernel, peanut butter, black pepper, mayonnaise, and peach) was 15 h when inoculated at 1–100 CFU/25 g sample. These results show the potential of HEK-DualTM hTLR5 cell-based functional biosensors for rapid screening of Salmonella.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

The cyclic AMP-responsive element-binding protein H (CREBH, encoded by CREB3L3) is a membrane-bound transcriptional factor that primarily localizes in the liver and small intestine. CREBH governs triglyceride metabolism in the liver, which mediates the changes in gene expression governing fatty acid oxidation, ketogenesis, and apolipoproteins upregulating LPL activity. A deficiency of CREBH in mice leads to severe hypertriglyceridemia. CREBH, in synergy with PPARα, has a crucial role in upregulating Fgf21 expression, which is implicated in metabolic homeostasis. CREBH binds to and functions as a co-activator for both PPARα and LXRα in regulating gene expression of lipid metabolism. Furthermore, intestinal CREBH in overexpression reduces cholesterol absorption and suppresses high-cholesterol diet-induced fatty liver. Conversely, a deficiency of CrebH in mice fed on various high-fat diets leads to severe fatty liver. Thus, CREBH could be a therapeutic target in the treatment of metabolic diseases.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

Background: Diet is a risk factor for gestational diabetes mellitus (GDM). There are few studies on women´s diet and glucose tolerance test (GTT) results. Objective: To evaluate the relationship between previous diet and the number of abnormal values on the diagnostic GTT in women with GDM. We hypothesized there would be an inverse relation between antioxidant micronutrient consumption and the number of abnormal GTT values. Methods: This cross-sectional study included 60 women diagnosed with GDM (2-hours, 75g-GTT). Shortly after diagnosis, participants answered a validated food frequency questionnaire to assess food consumption in the last 6 months. Mann-Whitney´s test was used to compare the dietary intake of participants with one (group 1) versus two-three (group 2) abnormal GTT values. Results: Participant characteristics were similar. There were no significant differences between groups in median intake of total calories, carbohydrates, lipids and proteins. Participants in group 1 had significantly higher intakes of fiber (11.9 vs. 11.0 g/day p= 0.049), vitamin D (40.6 vs. 40.4 mcg/day p= 0.049) and vitamin C (180.0 vs. 151.0 mg/day p= 0.008) than those in group 2. Conclusion: Results suggest a possible association between consumption of fiber and some antioxidant micronutrients and GDM severity at the time of diagnosis.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Survivability is a critical concern in WSNs, heavily influenced by energy efficiency. Addressing severe energy constraints in WSNs requires solutions that meet application goals while prolonging network life. This paper presents an energy optimization approach (EOAMRCL) for WSNs, integrating the Grey Wolf Optimization (GWO) for enhanced performance. EOAMRCL aims to enhance energy efficiency by selecting the optimal duty-cycle schedule, transmission power, and routing paths. The proposed approach employs a centralized strategy using a hierarchical network architecture. During the cluster formation phase, an objective function, augmented with GWO, determines the ideal cluster heads (CHs). The routing protocol then selects routes with minimal energy consumption for data transmission to CHs, using transmission power as a metric. In the transmission phase, the MAC layer forms a duty-cycle schedule based on cross-layer routing information, enabling nodes to switch between active and sleep modes according to their network allocation vectors (NAV). This process is further optimized by an enhanced CSMA/CA mechanism, which incorporates sleep/activate modes and pairing nodes to alternate between active and sleep states. This integration reduces collisions, improves channel assessment accuracy, and lowers energy consumption, thereby enhancing overall network performance. EOAMRCL was evaluated in a MATLAB environment, demonstrating superior performance compared to EEUC, DWEHC, and CGA-GWO protocols, particularly in terms of network lifetime and energy consumption. This highlights the effectiveness of integrating GWO and the updated CSMA/CA mechanism in achieving optimal energy efficiency and network performance.

This article uses machine learning analysis of wearable sensor data to explore the topic of driver differentiation. The study focuses on using detailed analyzes of data collected from wearable sensors to identify patterns that differentiate skilled drivers from inexperienced ones. On a predetermined driving route, participants experienced a variety of driving conditions, including parking, navigating cities, driving on highways and driving through residential neighborhoods. The gathered data was analyzed using machine learning techniques, yielding a classification accuracy of 94% overall. The results highlight important differences in sensor data between inexperienced and experienced drivers, providing insight into possible uses for improving safety protocols, driver education, and personalized feedback systems. The article fosters improvements in traffic safety and driver education by offering insightful information on the link between driver behavior analysis and machine learning.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

Of the 100,000 railroad bridges in the United States, 50% are over 100 years old. Many of these bridges do not meet the minimum vertical clearance standards, making them susceptible to impacts from over-height vehicles. Impacts can cause structural damage and unwanted disruption to railroad bridge services; rapid notification of the railroad authorities is crucial to ensure that the bridges are safe for continued use and to affect timely repairs. Therefore, researchers have developed approaches to identify these impacts to railroad bridges. Some recent approaches use machine learning to more effectively identify impacts from the sensor data. Typically, the collected sensor data is transmitted to a central location for processing. However, the challenge with this centralized approach is that the transfer of data to a central location can take considerable time, which is undesirable for time-sensitive events like impact detection that require rapid assessment and response to potential damage. To address the challenges posed by the centralized approach, this study develops a framework for edge implementation of machine learning predictions on wireless smart sensors. Wireless sensors are used because of their ease of installation and lower costs compared to their wired counterparts. The framework is implemented on the Xnode wireless smart sensor platform, thus bringing artificial intelligence models directly to the sensor nodes and eliminating the need to transfer data to a central location for processing. This framework is demonstrated using data obtained from events on a railroad bridge near Chicago; results illustrate the efficacy of the proposed edge computing framework for such time-sensitive structural health monitoring applications.

The objective of this pilot study was to compare glucose concentrations in capillary blood (CB) samples analysed in a laboratory by a validated method and glucose concentrations measured in the interstitial fluid (ISF) by continuous glucose monitoring under different physical activity levels in a postprandial state in healthy and active subjects without diabetes. Ten healthy, active subjects (26±4 years, 67±11 kg bodyweight (BW), 11±3 h) were included in the study. Within 14 days, they underwent six tests consisting of a) resting fasted (R/Fast), b) resting after intake of 1 g glucose/kg BW (R/Glc) and c) running for 60 minutes at moderate (65/Glc) and d) high (85/Glc) intensity after intake of 1 g glucose/kg BW. Data were collected in the morning, following a standardised dinner before test day. Sensor-based glucose concentrations were compared to simultaneous capillary blood glucose concentrations. Pearson’s r correlation coefficient was highest for R/Glc (.92, p<.001) compared to R/Fast (.45, p<.001), 65/Glc (.60, p<.001) and 85/Glc (.70, p<.001). Mean absolute relative deviation (MARD) and standard deviation (SD) was smallest for resting fasted and similar between all other conditions (R/Fast: 8±6%, R/Glc: 17±12%, 65/Glc: 22 ± 24%, 85/Glc: 18±17%). However, Bland-Altman plot analysis showed a higher range between lower and upper limits of agreement (95% confidence interval) of paired data under exercising compared to resting conditions. Under resting fasted conditions, both methods produce similar outcomes. Under resting postprandial and exercising conditions, respectively, there are differences between both methods. However, further data in healthy subjects need to be gathered considering physical activity and nutrition status.

In this work, an enzymatic sensor, based on a bionanocomposite film consisting of a polyelectrolyte complex (PEC) [Chitosan/kappa-carrageenan] doped with gold nanoparticles (AuNPs) encapsulating glucose oxidase (GOD) deposited on a gold electrode (Au) for glucose sensing, is described. Using the electrocatalytic synergy of AuNPs and GOD as a model of enzyme, the variation of the current (µA) as a function of the log of the glucose concentration (log [glucose]), shows 3 times higher sensitivity for the modified electrode (283.9) compared to that of the PEC/GOD modified electrode (93.7), with a detection limit of about 5 µM and a linearity range between 10µM and 7mM. The response of the PEC/AuNPs/GOD based biosensor also presents good reproducibility, stability and negligible interfering effects from ascorbic acid, uric acid, urea and creatinine. The applicability of the PEC/AuNPs/GOD based biosensor was tested in glucose-spiked saliva samples and acceptable recovery rates were obtained.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

Rho guanosine triphosphatases (GTPases) are key regulators in a number of cellular functions, including actin cytoskeleton remodeling and vesicle traffic. Traditionally, Rho GTPases are studied because of their function in cell migration and cancer, while their roles in metabolism are less documented. However, emerging evidence implicates Rho GTPases as regulators of processes of crucial importance for maintaining metabolic homeostasis. Thus, the time is now ripe for reviewing Rho GTPases in the context of metabolic health. Rho GTPase-mediated key processes include the release of insulin from pancreatic β-cells, glucose uptake into skeletal muscle and adipose tissue, and muscle mass regulation. Through the current review, we cast light on the important role of Rho GTPases in skeletal muscle, adipose tissue, and the pancreas and mechanisms by which Rho GTPases act to regulate glucose metabolism in health and disease. We also describe challenges and goals for future research.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

Background/Objectives: The global burden of metabolic dysfunction-associated steatotic liver disease (MASLD) is increasing at an alarming rate. Cardiovascular disease (CVD) is the leading cause of mortality in MASLD patients, therefore, the therapeutic interventions for MASLD should improve coronary risk factors such as obesity, diabetes and dyslipidemia, in addition to improving liver function. The evidence on effect of sodium-glucose cotransporter 2 inhibitors (SGLT2is) which have beneficial pharmacological properties for MASLD, especially the long-term effects, on the progression of MASLD in Asian population is very limited. Methods: The retrospective longitudinal study was performed by using the medical records at the National Center for Global Health and Medicine, Kohnodai Hospital, Japan. We picked up patients with type 2 diabetes who had taken SGLT2is for at least 3 years or longer between April 1, 2014 and March 31, 2018. We collected the data on metabolic parameters, including blood tests and anthropometric parameters, and compared the data before and after the initiation of SGLT2is treatment. Results: During the observation period, 324 patients had taken SGLT2is for 3 years. The 3-year-SGLT2is treatment significantly reduced body weight, hemoglobin A1c, low-density lipoprotein-cholesterol, triglyceride and non-high-density lipoprotein-cholesterol (HDL-C) and significantly increased HDL-C. Furthermore, this treatment significantly improved liver function and the markers for hepatic steatosis and hepatic fibrosis. Conclusions: Considering that the development of CVD determines the prognosis of MASLD patients, the long-term SGLT2is treatment may be an ideal therapy for MASLD patients.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

This paper introduces a novel decision-making approach grounded in insights into human visual perception of change. Modern technologies such as internet of things (IoT) provide us with large amounts of sensor data that need to be processed in real time and decisions made with a high degree of accuracy and reliability. Artificial intelligence (AI) methods are welcome in this context and need to be upgraded to meet actual challenges. While modern computing capabilities facilitate rapid data processing, the real-time demands of vast sensor data necessitate swift responses across the cyber chain, often leading to compromises in solution quality to circumvent combinatorial search complexities. Determining the adequacy of a solution entails varied approaches, often relying on heuristic methodologies. We illustrate our original approach with an example of a selected detail of a differential evolution algorithm, where we have to make a decision to adopt the best solution so far. We propose an approach inspired by human perceptual features that exploits the Weber-Fechner law to emulate human judgements, and offers a promising way to improve decision making in AI applications and real-time requirements fulfillment. Our proposed methodology demonstrates applicability across diverse AI scenarios involving numerical data, effectively mirroring human perception abilities.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Objectives and Background: Gestational diabetes (GDM) is a common pregnancy complication, defined as a glucose intolerance diagnosis during pregnancy. GDM is strongly associated with adverse fetal and maternal outcomes. In Germany, to screen and diagnose GDM we use a 1-hour 50g oGCT (oral glucose challenge test) followed by a 2-hour 75g oGTT if the first was pathological. This analysis examines the correlation of 75g oGTT glucose levels and fetomaternal outcome. Methods: Data of 1664 patients from a gestational diabetes consultation clinic at the Charité University hospital in Berlin, Germany, were analyzed retrospectively from 2015 until 2022. The 75g oGTT blood glucose levels were categorized into isolated fasting hyperglycemia (GDM-IFH), isolated post-load hyperglycemia (GDM-IPH) and combined hyperglycemia (GDM-CH), using the levels of the fasting, 1-hour and 2-hour values after glucose application. These subtypes were compared regarding baseline characteristics as well as fetal and maternal outcome. Results: GDM-IFH and GDM-CH women displayed higher preconceptional BMI and required insulin therapy more frequently (p<0,001). The GDM-IFH group was at higher risk of having a primary cesarean section (p=0,047), while GDM-IPH women were significantly more likely to have an emergent cesarean section (p=0,013). The offspring of GDM-IFH and GDM-CH women were born with a significantly higher mean birthweight (p<0,001) and birth weight percentiles (p<0,001) and were at increased risk of being large for gestational age (LGA) (p=0,004). Women from the GDM-IPH group delivered significantly more neonates who were small for gestational age (p=0,027) or with low fetal weight <30th percentile (p=0,003). Conclusion: This analysis shows a strong association between glucose response pattern in the 75g oGTT and adverse perinatal fetomaternal outcome. The differences among the subgroups, specifically concerning insulin therapy, mode of delivery and fetal growth, suggest an individualized approach in prenatal care after a GDM diagnosis.

Increased chronic glucose is associated with pandemic diseases. To date, there is not a practical, as well as accurate sample for reflecting that level. We measured earwax glucose in 37 controls. They provided standard serum samples, Glycated Haemoglobin (HbA1c) and earwax samples on two time-points, one month a part. The specimens measured baseline fasting glucose, a follow-up postprandial glucose level and a between sample chronic glucose, calculated using the average level on the two occasions. The baseline earwax sample was obtained using a clinical method and the follow-up using a novel self-sampling earwax device. The earwax analytic time was significantly faster using the novel device in comparison to the clinical use of the syringe. Earwax accurately reflected glucose at both assessments with stronger correlations than HbA1c. Follow-up postprandial concentrations were more significant than their respective fasting baseline concentrations, reflecting differences in fasting and postprandial glycaemia and more efficient standardisation at follow up. Earwax demonstrated to be more predictable than HbA1c in reflecting systemic fasting, postprandial and long-term glucose levels and immune by confounders. Earwax glucose was approximately 60% more predictable than HbA1c in reflecting glycaemia over a month. The self-sampling device provided a sample that might accurately reflect chronic glycaemia.

Increased activity of transforming growth factor-beta (TGF-β) is a key factor mediating kidney impairment in diabetes. Glomerular podocytes, the crucial component of the renal filter, are a direct target of TGF-β action, resulting in irreversible cell loss and progression of chronic kidney disease (CKD). Urolithin A (UA) is a member of the family of polyphenol metabolites produced by gut microbiota from ellagitannins and ellagic acid-rich foods. The broad spectrum of biological ac-tivities of UA makes it a promising candidate for the treatment of podocyte disorders. In this in vitro study, we investigated whether UA influences the changes exerted in podocytes by TGF-β and high glucose. Following a 7-day incubation in normal (NG, 5.5 mM) or high (HG, 25 mM) glucose the cells were treated with UA and/or TGF-β1 for 24 hours. HG and TGF-β1, each independent and in concert reduced expression of nephrin, increased podocyte motility and up-regulated expression of b3 integrin and fibronectin. These typical for epithelial-to-mesenchymal transition (EMT) effects were inhibited by UA in both HG and NG conditions. UA also reduced the typically elevated in HG expression of TGF-β receptors and activation of TGF-β signal transducer Smad2. Our results indicate that in podocytes cultured in conditions mimicking diabetic milieu, UA inhibits and reverses changes underlying podocytopenia in diabetic kidneys. Hence, UA should be considered as a po-tential therapeutic agent in podocytopathies.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

Common genetic variants of the fat mass and obesity associated (FTO) gene are strongly associated with obesity and type 2 diabetes. FTO is ubiquitously expressed, but appears to have tissue-specific roles. Earlier studies have focused on the role of hypothlamic FTO in the regulation of metabolism. However, it appears that FTO plays a role in the regulation of metabolism in a tissue-specific manner. Recent studies suggest that expression of hepatic FTO is regulated by metabolic signals such as nutrients and hormones and altered FTO levels in liver affects glucose and lipid metabolism. This review outlines recent findings on hepatic FTO in the regulation of metabolism, with particular focus on hepatic glucose and lipid metabolism. It is proposed that abnormal activity of hepatic signaling pathways involving FTO links metabolic impairments such as obesity, type 2 diabetes and nonalcoholic fatty liver disease (NAFLD). Therefore, a better understanding of these pathways may lead to therapeutic approaches to treat these metabolic diseases by targeting hepatic FTO. The overall goal of this review is to place FTO within the context of hepatic regulation of metabolism.

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

Increased sugar intake is implicated in Type-2 diabetes and fatty liver disease. Mechanisms by which glucose and fructose components promote these conditions are unclear. We hypothesize that alterations in intestinal metabolite and microbiota profiles specific to each monosaccharide are involved. Two groups of six adult C57BL/6 mice were fed for 10-weeks with a diet where either glucose or fructose was the sole carbohydrate component (G and F, respectively). A third group was fed with normal chow (N). Fecal metabolites were profiled every 2-weeks by ¹H NMR and microbial composition was analysed by real-time PCR (qPCR). Glucose tolerance was also periodically assessed. N, G and F mice had similar weight gains and glucose tolerance. Multivariate analysis of NMR profiles indicated that F mice were separated from both N and G, with decreased butyrate and glutamate and increased fructose, succinate, taurine, tyrosine and xylose. Compared to N and G, F mice showed a shift in microbe populations from gram-positive Lactobacillus spp. to gram-negative Enterobacteria species. Substitution of normal chow carbohydrate mixture by either pure glucose or fructose for 10 weeks did not alter adiposity or glucose tolerance. However, F G and N mice generated distinctive fecal metabolite signatures with incomplete fructose absorption as a dominant feature of F mice.

in our increasingly interconnected world, sensor networks are critical in gathering and sending data for various applications, from environmental monitoring and industrial automation to healthcare and smart cities. However, as sensor networks expand in importance, so does the need to solve the multidimensional concerns of security, privacy, and forensics. This article explores the complex world of sensor network security, the delicate balance between data privacy and utility, and the emerging area of sensor network forensics. This article focuses on risk assessment of a network.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

The study put forward a data fusion approach for urban remote sensing that combines SAR (Synthetic Aperture Radar) and optical satellite data. By integrating datasets from different sensors and spatial-temporal scales, the technique aims to extract more accurate information. The fusion approach utilizes two methods: feature-based fusion, where relevant features are extracted and fused, and simple layer stacking (SLS), where the original datasets are directly stacked as multiple layers. This study extracted features using SAR textures (using Sentinel-1) and modified indices (using Landsat-8), and then classified these features using an XGBoost algorithm implemented in Python and Google Earth Engine. Researchers examined five cities, each representing a distinct climatic zone and urban dynamic: Cape Town, Guangzhou, Los Angeles, Mumbai, and Osaka. An accuracy assessment was conducted using random validation points, achieving an overall accuracy of 89.5% using the proposed MSFI method. A comparison was also performed with three well-known global products. The proposed approach, outperformed all three global products achived 89% accuracy while ESA (84%), ESRI (81%) and Dynamic World (82%). Additionally, Land surface temperature analysis was accomplished to investigate the relationship between extracted UIS and Land Surface Temperature (LST) across selected cities to show the practical use of proposed MSFI method. Los Angeles, a warm temperate city, showed the highest LST among all five cities. The datasets, along with the GEE and Python codes, are available at https://github.com/mnasarahmad/sls.

The kidney and the heart work together in balancing the body circulation and although their physiology is based on strict inter dependence, their performance fulfills different aims. While the heart can rapidly increase its own oxygen consumption to comply with the wide changes in metabolic demand linked to body function, the kidney physiology is primarily designed to maintain a stable metabolic rate and has limited capacity to cope with any steep increase in renal metabolism. In the kidneys the glomerular population filters a large amount of blood and the tubular system has been programmed to reabsorb 99% of filtrate by reabsorbing sodium together with other filtered substances including all glucose molecules. Glucose reabsorption involves the sodium-glucose cotransporters SGLT2 and SGLT1 on the apical membrane in the proximal tubular section; it also enhances bicarbonate formation so as to preserve the acid-base balance. The complex work of reabsorption in the kidney is the main factor in renal oxygen consumption; analysis of renal glucose transport in disease states is providing better understanding of the renal physiology changes that occur when clinical conditions alter the neurohormonal response leading to an increase in glomerular filtration pressure. In this circumstance glomerular hyperfiltration occurs, imposing a higher metabolic demand on kidney physiology and causing progressive renal impairment. Albumin urination is the warning signal of renal engagement over-exertion and most frequently heralds heart failure development, regardless of disease etiology. The review analyzes the mechanisms linked to renal oxygen consumption, focusing on sodium-glucose management.

Background. Cardiorespiratory fitness (CRF) is a predictor of chronic disease that is impractical to routinely measure in primary care settings. We used a new estimated cardiorespiratory fitness (eCRF) algorithm that uses information routinely documented in electronic health care records to predict abnormal blood glucose incidence. Methods: Participants were adults (17.8% female) 20-81 years old at baseline from the Aerobics Center Longitudinal Study between 1979 and 2006. eCRF was based on sex, age, body mass index, resting heart rate, resting blood pressure, and smoking status. CRF was measured by maximal treadmill testing. Cox proportional hazards regression models were established using eCRF and CRF as independent variables predicting the abnormal blood glucose incidence while adjusting for covariates. Results: Of 8,602 participants at risk at baseline, 3,580 (41.6%) developed abnormal blood glucose during an average of 4.9 years follow-up. The average eCRF of 12.03 ± 1.75 METs was equivalent to the CRF of 12.15 ± 2.40 METs within the 10% equivalence limit. In fully adjusted models, the estimated risks were the same (HRs = 0.96), eCRF (95% CIs = 0.93−0.99), and CRF (95% CI of 0.94−0.98). Each 1-MET increase was associated with a 4% reduced risk. Conclusion: Higher eCRF is associated with a lower risk of abnormal glucose. eCRF can be a vital sign used for research and prevention.

A human organism depends on stable glucose blood levels in order to maintain the metabolic needs. Glucose is considered as the most important energy source and glycolysis is postulated as a backbone pathway. However, when glucose supply is limited, ketone bodies and amino acids can be used to produce enough ATP. In contrast, for the functioning of pentose phosphate pathway (PPP) glucose is essential and cannot be substituted by other metabolites. PPP generates and maintains levels of NADPH needed for reduction of oxidized glutathione and protein thiols, synthesis of lipids and DNA as well as for xenobiotic detoxification, regulatory redox signaling and counteracting infections. Flux of glucose into a PPP, particularly under extreme oxidative and toxic challenges is critical for survival, whereas the glycolytic pathway is primarily activated when glucose is abundant, and there is lack of NADP⁺ that is required for activation of glucose-6 phosphate dehydrogenase. An important role of glycogen stores in resistance to oxidative challenges is discussed. Current evidences explain disruptive metabolic effects and detrimental health consequences of chronic nutritional carbohydrate overload and provides new insights into positive metabolic effects of intermittent fasting, caloric restriction, exercise, and ketogenic diet through modulation of redox homeostasis.

Background: Obesity among pregnant women is common, and their offspring are predisposed to obesity, insulin resistance, and diabetes. Circulating metabolites that are related to insulin resistance and are associated with this decreased tissue-specific uptake are unknown. Here, we assessed metabolite profiles in elderly women and who were either female offspring from obese mothers (OOM) or offspring of lean mothers (OLM). Metabolic changes were tested for associations with metrics for insulin resistance. Methods: 37 elderly women were separated into an elderly offspring from obese mothers (OOM; n = 17) and elderly offspring from lean/normal weight mothers (OLM; n = 20) groups. We measured plasma metabolites using 1H-NMR and also insulin-dependent tissue specific glucose uptake in skeletal muscle were assessed. Associations were made between metabolites and glucose uptake. Results: Compared to the OLM group, we found that the 22:6 docosahexaenoic acid percentage of the total long chain n-3 fatty acids (DHA/FA) was significantly lower in OOM (P = 0.015). DHA/FA associated significantly to skeletal muscle GU (P = 0.031) and M-value in the OLM group only (P = 0.050). Conclusions: DHA/FA is associated with insulin-dependent skeletal muscle glucose uptake and that this association is significantly weakened in the offspring of obese mothers.

This ambitious research project seeks to revolutionize sustainable glucose production by harnessing solar energy for the conversion of atmospheric gases. The process involves water collection, electrolysis for hydrogen and oxygen production, PDMS membrane-based CO2 collection, CO2 splitting, formaldehyde generation, and the synthesis of glucose/sucrose. Key innovations include the strategic application of PDMS membranes with varying pore sizes and non-reactive chemical layers to facilitate selective permeability for specific gases. Our goal is to create a cost-effective, eco-friendly glucose production method, paving the way for renewable and sustainable energy solutions.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

Kaempferia parviflora Wall. ex Baker (KP), Krachaidam in Thai or Thai ginseng, is an herbal medicine that has many potential pharmacological effects. This study focused on the oral glucose tolerance test and pharmacokinetic study in healthy volunteers administered with KP extract (90 and 180 mg/day, placebo). The oral glucose tolerance tests were performed at baselines and 28-days of administration. The pharmacokinetics were determined after a single dose administration of the tested products using 3,5,7,3,4-pentamethoxyflavone (PMF) and 5,7,4-trimethoxylfavone (TMF) as markers. The results showed that glucose metabolism via oral glucose tolerance test was not affected by KP extract. The results of pharmacokinetics study revealed that only TMF and PMF, but not DMF levels could be detected in human blood. The given doses of KP extract at 90 and 180 mg/day showed a linear dose-relationship of blood PMF concentration whereas blood TMF was detected only at high given dose (180 mg/day). The half-lives of PMF and TMF were 2–3 h. The Cmax, AUC and Tmax values of PMF and TMF estimated for the 180 mg/day dose were 85.3711.31, 73.2329.93 mg/ml; 291.8948.23, 412.20203.69 mg.h/ml; and 3.890.37, 4.500.96 h, respectively. PMF was quickly eliminated with higher Ke and Cl than TMF at the dose of 180 mg/day of KP extract. In conclusion, the results demonstrated that KP extract had no effect on glucose tolerance test. In addition, this is the first demonstration of the pharmacokinetic parameters of methoxyflavones of KP extract in healthy volunteers in a phase I study in drug development. The data suggest the safety of the KP extract and will be of benefit for further clinical trials using KP extract as food and sport supplements as well as a drug in health product development.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The integration of Wireless Sensor Networks (WSNs) into agricultural areas has had a significant impact and has provided new, more complex, efficient, and structured solutions for enhancing crop production. This research reviews the role of Wireless Sensor Networks (WSNs) in monitoring the macro-nutrient content of plants. The review study focuses on identifying the types of sensors used to measure macro-nutrients, determining sensor placement within agricultural areas, implementing wireless technology for sensor communication, and selecting device transmission intervals and ratings. The study of NPK (Nitrogen, Phosphorus, Potassium) monitoring using sensor technology in precision agriculture is of high significance in efforts to improve agricultural productivity and efficiency. In addition to fostering technological innovations and precision farming solutions, in future this research aims to increase agricultural yields, particularly by enabling the cultivation of certain crops in locations different from their original ones.

A key response to glucose stress is an increased production of unsaturated fatty acids to balance the increase of saturated fatty acids in the membrane. The C. elegans homolog of stearoyl-CoA desaturase, FAT-7, introduces the first double bond into saturated C18 fatty acids yielding oleic acid and is a critical regulatory point for surviving cold and glucose stress. Here, we incorporated 13C stable isotopes into the diet of nematodes and quantified the 13C-labelled fatty acid by GC-MS and HPLC/MS-MS to track the metabolic response to various concentrations of glucose. Previous work has analyzed membrane composition of C. elegans when responding to mild glucose stress and showed few alterations in overall fatty acid composition in the membrane. Here, in nematodes exposed to higher concentrations of glucose, a specific reduction of oleic acid and linoleic acid was observed. Using time courses and stable isotope tracing, the response of fatty acid me-tabolism to increasing levels of glucose stress has been characterized, revealing a funneling of monounsaturated fatty acids to preserve polyunsaturated fatty acid abundance. Taken together, higher levels of glucose unveil a specific reduction of oleic and linolenic acid in the metabolic re-wiring required to survive glucose stress.

As an option to deal with the insulin-dependent disease, a recent commuted PD control strategy is designed and carefully analyzed for different clinic diabetic patients. This controller approach is mainly conceived to stabilize the glucose blood concentration in a diabetic patient around its basal value, hence avoiding extreme situations such as hypoglycemia and hyperglycemia. This control strategy receives two inputs carefully tuned to actuate when the measured variable is out of a prescribed healthy zone. Therefore, one of these variables is invoked to decrease the glucose concentration to insulin injection, and the other is employed to increase the glucose absorption, both by using a proper PD controller. According to our numerical experiments, our controller approach performs well, even when there is an external disturbance in the controlled system.

Nanocomposite hydrogels offer remarkable potential for applications in bone tissue engineering. They are synthesized through the chemical or physical crosslinking of polymers and nanomaterials, allowing for the enhancement of their behaviour by modifying the properties and compositions of the nanomaterials involved. However, their mechanical properties require further enhancement to meet the demands of bone tissue engineering. Here, we present an approach to improve the mechanical properties of nanocomposite hydrogels by incorporating polymer grafted silica nanoparticles into a double network inspired hydrogel (gSNP Gels). The gSNP Gels were synthesised via a graft polymerization process using a redox initiator. gSNP Gels were formed by grafting 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as the first network gel followed by a sequential second network acrylamide (AAm) onto amine functionalized silica nanoparticles (ASNPs). We utilized glucose oxidase (GOx), to create an oxygen-free atmosphere during polymerization resulting in higher polymer conversion compared to argon degassing. The gSNP Gels showed excellent compressive strengths of 13.9 ± 5.5 MPa, a strain of 69.6 ± 6.4%, and a water content of 63.4% ± 1.8. The synthesis technique demonstrates a promising approach to enhance the mechanical properties of hydrogels, which can have significant implications for bone tissue engineering and other soft tissue applications.

Pathogens and adulterants in human feeding consumables can be readily identified according to their electrical properties. Electrical bioimpedance analysis (BIA) has been widely used for body contents characterization, such as blood, urine, lactate and sweat. If the blood glucose concentration alters the electrical properties of the blood medium, then the impedance spectrum obtained by BIA can be used to measure glycemia. In some applications, artificial neural networks allows the correlation of these parameters (impedance and glucose concentration) by means of symbolic and statistical rules. According to our literature review, there is any physical model that allows the interpretation of the relationship between blood’s electrical properties, obtained by BIA, and the concentration of glucose in the blood plasma. This article proposes a simplified physical model for blood electrical conductivity as a function of glucose concentration, based on Bruggeman’s effective medium theory. The equations of this model were obtained considering an insulating phase distribution diffused in a conductive matrix, in which red blood cells are represented by macroscopic insulating nuclei and glucose molecules by microscopic insulating particles. The impedance spectrum for different glucose concentrations (4.0 to 6.8 mmol/L) in a blood sample, published by Kamat Bagul (2014), were compared with the proposed model. The results showed a significant correlation with the experimental data, showing a maximum error of 5.2%. The proposed model might be useful in the design of noninvasive blood glucose monitoring systems.

Calorie restriction (CR) has been shown to prolong the lifespan of humans, but enforcing long-term CR is difficult. Therefore, a compound that reproduces the effect of CR without CR is needed. In this review, we summarize the current knowledge on compounds with CR mimetic (CRM) effects. More than 10 compounds have been listed as CRMs, some of which are conventionally categorized as upstream-type CRMs showing glycolytic inhibition while the others are categorized as downstream-type CRMs that regulate or genetically modulate intracellular signaling proteins. Among these, we focus on upstream-type CRMs and propose their classification as compounds with energy metabolism inhibition effects, particularly glucose metabolism modulation effects. The upstream-type CRMs reviewed include chitosan, acarbose, sodium-glucose cotransporter 2 inhibitors, and hexose analogs such as 2-deoxy-D-glucose, D-glucosamine, and D-allulose, which show anti-aging and longevity effects. Finally, we discuss the molecular definition of upstream-type CRMs.

The prevalence of diabetes mellitus (DM), considered one of the most common metabolic disorders, has dramatically increased and resulted in higher rate of morbidity and mortality around the world, in the past decade. It is well known that insulin resistance in target tissues and a deficiency in insulin secretion from pancreatic β-cells are the main characteristic of type 2 diabetes. The aim of this study was the bio-evaluation of compounds isolated from three selected plant species; namely, Salvia africana-lutea, Leonotis ocymifolia and Plectranthus madagascariensis, for their glucose uptake ability. Methanolic extracts were produced from the arterial part of each plant. Compounds were identified using different spectroscopic techniques. The glucose uptake ability of each compound was then evaluated in mammalian cells using 2-deoxyglucose-6-phosphate. The cytotoxicity of each compound was established via the MTT assay. Chromatographic purification of the three plant species yielded fifteen pure terpenoids. Compounds 1 (p = 0.0031), 8 (p = 0.0053), and 6 (p = 0.0086), showed a marked increase in glucose uptake, with p values of p=0.0031, p=0.0053 and p=0.0086, respectively. Additionally, 1, 4 and 6 exhibited cytotoxicity toward mammalian tissue with a decrease in cell viability of ~70%, ~68% and ~67%, respectively. The results suggested that several compounds demonstrated a marked increase in glucose uptake while two of the compounds exhibited signs of cytotoxicity. It may, therefore, be suggested that these compounds be considered as potential candidates for novel plant-derived alternative therapies in the treatment of type 2 diabetes.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Quasi-bound state in the continuum (QBIC) can effectively enhance the interaction of terahertz (THz) wave with matters due to the tunable high-Q property, which has a strong potential application in detection of low-concentration biological samples in the THz band. In this paper, a novel THz metamaterial sensor with a double-chain separated resonant cavity structure based on QBIC is designed and fabricated. The process of excitation of the QBIC mode is verified and the structural parameters are optimized after considering the ohmic loss by simulations. The simulated refractive index sensitivity of the sensor is up to 544 GHz/RIU, much higher than those of recently reported THz metamaterial sensors. Sensing sensitivity of the proposed metamaterial sensor is confirmed in experiment by detecting low-concentration lithium citrate (LC) and bovine serum albumin (BSA) solutions. The limits of detection (LoDs) are obtained to be 0.0025 mg/mL (12 μM) for LC and 0.03125 mg/mL (0.47 μM) for BSA, respectively, both of which excel over most of reported results in previous studies. These results indicate that the proposed THz metamaterial sensor has excellent sensing performances and can well be applied to the detection of low concentration biological samples.

We present a data-driven, in situ proximal multi-sensor digital soil mapping approach to develop digital twins for multiple agricultural fields. A novel Digital Soil CoreTM (DSC) Probe was engineered that contains seven sensors, each of a distinct modality, including sleeve friction, tip force, dielectric permittivity, electrical resistivity, soil imagery, acoustics, and visible and near-infrared spectroscopy. The DSC System integrates components the DSC Probe, DSC software, and deployment equipment to sense soil characteristics at a high vertical spatial resolution (mm scale) along in situ soil profiles up to a depth of 120 cm in about 60 sec. The DSC Probe in situ proximal data are harmonized into a data cube providing vertical high-density knowledge associated with physical-chemical-biological soil conditions. In contrast, conventional ex situ soil samples derived from soil cores, soil pits, or surface samples analyzed using laboratory and other methods are bound by substantially coarser spatial resolution and multiple compounding errors. Our objective was to investigate the effects of mismatched scale between high-resolution in situ proximal sensor data and coarser resolution ex situ soil laboratory measurements to develop soil prediction models. Our study was conducted in central California soil in almond orchards. We collected DSC sensor data and spatially co-located soil cores that were sliced into narrow layers for laboratory-based soil measurements. Partial Least Squares Regression (PLSR) cross-validation was used to compare results testing four data integration methods. Method A reduced the high-resolution sensor data to discrete values paired with layer-based soil laboratory measurements. Method B used stochastic distributions of sensor data paired with layer-based soil laboratory measurements. Method C allocated the same soil analytical data to each one of the high-resolution multi-sensor data within a soil layer. Method D linked the high-density multi-sensor soil data directly to crop responses (crop performance and behavior metrics) bypassing costly laboratory soil analysis. Overall, the soil models derived from Method C outperformed Methods A and B. Soil predictions derived using Method D were most cost-effective for directly assessing soil-crop relationships, making this method well-suited for industrial-scale precision agriculture applications.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.