The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

The Krudum granite body comprises highly fractionated granitic rocks ranging from medium-F biotite granites to high-F, high-P₂O₅ Li-mica granites. This unique assemblage is an ideal site to continue recent efforts in petrology to characterize the role of zircon, monazite and xenotime as hosts to REEs. The granitic rocks of the Krudum body analysed in this study were found to contain variable concentrations of monazite and zircon, while xenotime was only found in the high-F, high-P₂O₅ Li-mica granites and in the alkali-feldspar syenites of the Vysoký Kámen stock. For analysed monazites of all magmatic suites cheralite substitution was significant. The highest concentration of cheralite was found in monazites from the high-F, Li-mica granites and from the alkali-feldspar syenites. The proportion of YPO₄ in all analysed xenotimes ranges from 71 to 84 mol. %. Some xenotimes were found to be hydrated and the observed water content estimated from analytical data ranged from 5 to 11 wt. % H₂O. Analysed xenotimes were commonly enriched in HREEs (9.3– 19.5 wt. % HREE₂O₃) and thorite-coffinite and cheralite exchange was observed. Analysed zircons from granite suites of the Krudum granite body contained moderate Hf concentrations (1.0–4.7 wt. % HfO₂; 0.010–0.047 apfu Hf). The highest concentrations of HfO₂ were found in zircons from the high-F, high P₂O₅ Li-mica granites (1.2–4.7 wt. % HfO₂) and from the alkali-feldspar syenites (1.3–4.1 wt. % HfO₂). Zircons from the high-F, high-P₂O₅ Li-mica granites were often hydrated and fluorised. The concentrations of F in zircon from partly greisenised high-F, high-P₂O₅ Li-mica granites reached up to 1.2 wt. % (0.26 apfu F). In zircons from the alkali-feldspar syenites enrichment in P, which is not associated with a simultaneous enrichment in Y + REE, was also observed. Analysed zircons from the high-F, high P₂O₅ Li-mica granites were enriched in Y (up to 5.5 wt. % Y₂O₃; 0.10 apfu Y) and Sc (up to 1.17 wt. % Sc₂O₃; 0.03 apfu Sc).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

In crystal structure prediction, Newton's second law can always be applied to particles (atoms or ions) in a cell to determine their positions. However the values of the period vectors (crystal cell edge vectors) should be determined as well. Here we applied the dynamical equations of period vectors derived recently based on Newton's laws (doi:/10.1139/cjp-2014-0518) for that purpose, where the period vectors are driven by the imbalance between the internal and external pressures/stresses. For equilibrium states, they became equations of state, which essentially turn out the equilibrium conditions of crystals from mechanical point of view. For external pressure, by ignoring some effects, they reduced to the Mie-Gruneisen equation. Since the internal stress has both a full kinetic energy term and a full interaction term, the influences of both external temperature and stress/pressure on crystal structures can be calculated, then thermodynamical properties and processes were presented. Contrary to usual ideas, the equations show that pure harmonic vibrating phonons can result in thermal expansion in crystals when the external temperature is changed. Finally, crystal system collapse due to temperature and/or stress/pressure change was discussed.

The Macroscopic Mechanical Equilibrium Condition can be shown to be the physical origin of the Equation of State of any material system, then can describe all thermodynamic quasi-equilibrium processes caused by the change of the external temperature and/or mechanical environment. If it cannot be satisfied, the system would be broken.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

For crystal periodic structure prediction, a new and concise approach based on the principles of statistical physics was employed to derive a new form of the equation to determine their period vectors (cell edge vectors), under general external stress. Then the new form is applicable to both classical physics and quantum physics. It also turned out to be the equation of state and the mechanical equilibrium condition for crystals under external stress and temperature. It should be helpful in piezoelectric and piezomagnetic studies, as the period vectors were changed by the external stress. For linear elastic crystals, it is actually also the microscopic but temperature-dependent form of the generalized Hooke's law, then can be used to calculate the corresponding elastic constants of the law, for given temperatures.

This paper uses event study analysis to estimate the impact of the Fed’s Quantitative Easing (QE) announcements on the mortgage market during zero lower bound period. A total of 35 QE announcements are identified and their effects are evaluated. The best-fitting IGARCH model with skewed t distribution is used to measure the QE announcement effects on daily changes of the 30-year mortgage rate, the 30-year Treasury rate and the spread between them. Announcements suggesting the start of a new round of QE reduced the mortgage rate tremendously, while the effects of further news diminished. Announcements of an increase in mortgage-backed security purchases decreased the mortgage rate more than the Treasury rate and reduced the credit risk of holding mortgage securities over Treasury securities. The long run effects of QE announcements on the mortgage rate were less than short run effects but persistent. We also find that the previous literature overestimate QE effects on interest rates in general.

Since crystals are made of periodic structures in space, predicting their three period vectors starting from any values based on the inside interactions is a basic theoretical physics problem. For the general situation where crystals are under constant external stress, we derived dynamical equations of the period vectors in the framework of Newtonian dynamics, for pair potentials recently (doi:/10.1139/cjp-2014-0518). The derived dynamical equations show that the period vectors are driven by the imbalance between the internal and external stresses. This presents a physical process where when the external stress changes, the crystal structure changes accordingly, since the original internal stress can not balance the external stress. The internal stress has both a full kinetic energy term and a full interaction term. It is extended to many-body interactions in this paper. As a result, all conclusions in the pair-potential case also apply for many-body potentials.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

This paper presents a study to accurately evaluate defects in reinforced concrete decks using ultrasonic pulse-echo signals. Two validation specimens were designed and tested where reinforced concrete deck slab specimens included planned voids and defects. A commercial Ultrasonic Pulse-Echo (UPE) device obtains 2-D images of the void/defect locations of the reinforced concrete deck. The UPE is based on the ultrasonic shear-wave test method using dry-point-contact transmitting and receiving transducers and employing a synthetic aperture focusing technique. The authors analyzed the recorded UPE A-scan data to enhance the accuracy of estimating the defects' locations using the synthetic aperture focusing technique imaging method. The analysis benefitted from an advanced denoising approach and defect echo peak extraction based on empirical modal decomposition, Hurst exponent characterization, and Hilbert envelope estimation. While output from conventional UPC devices can only provide qualitative results, the new method provides quantitative information on the anomalies inside the reinforced concrete deck. The developed approach accurately assists with assessing the location and depth of the voids/defects in the reinforced concrete deck slabs.

We have presented a controllable and human-readable polynomial neural network (CR-PNN) that is the first human-readable neural network. One can imagine its influence on system identification. Subsequently, we developed a relation spectrum in a medical application, which is likely to stand alongside the Fourier spectrum. However, the system analysis methodology is incomplete in contrast to signal processing methodology. Here, we presented the system filters for the first time. In this paper, we used the simulation system to verify the availability of the system analysis methodology. The system analysis methodology showed great properties in system identification and filter. The contribution of this paper is the system analysis methodology: transform method (CR-PNN), relation spectrum, and system filter design.

Antimicrobial and anti-viral materials have attracted significant interest in recent years due to increasing occurrences of nosocomial infections and pathogenic microbial contamination. One method to address this is the combination of photoactive compounds that can produce reactive oxygen species (ROS), such as hydrogen peroxide and hydroxyl radicals to disinfect microbes, with carrier materials that meet the application requirements. Using anthraquinone (AQ) and cellulose nanocrystals (CNCs) as the photoactive and carrier components respectively, this work demonstrates the first covalent incorporation of AQ onto CNCs. The morphology and the photoactive properties were investigated, revealing the structural integrity of the CNCs, and high degree of photoactivity of AQ-CNC materials upon UVA exposure. The AQ-CNCs also exhibited an unexpected persistent generation of ROS under darkness, which adds advantages for antimicrobial applications.

The Meissner effect is a special property of superconductors. In this paper, based on the characteristics of the Meissner effect, a superconducting phase transition model of a superconductor under a changing magnetic field is proposed. A thermodynamic analysis was performed on the model to calculate both the changes in the thermodynamic parameters of the superconductor during the phase transition and the changes in the overall work and energy of the model. For Model 1 in the present study, the thermodynamic energy of the superconductor was not conserved due to the phase change of the superconductor under a changing magnetic field.

In this work, we study the dynamical behaviors of the electromagnetic fields and material responses in the hyperbolic metamaterial consisting of periodically arranged metallic and dielectric layers. The thickness of each unit cell is assumed to be much smaller than the wavelength of the electromagnetic waves, so the effective medium concept can be applied. When electromagnetic (EM) fields are present, the responses of the medium in the directions parallel to and perpendicular to the layers are like that of Drude and Lorentz media, respectively. We derive the energy density of the EM fields and the power loss in the effective medium based on Poynting theorem and the dynamical equations of the polarization field. We also show that the Lagrangian density of the system can be constructed. The Euler-Lagrangian equations yield the correct dynamical equations of the electromagnetic fields and the polarization field in the medium. The canonical momentum conjugates to every dynamical field can be derived from the Lagrangian density via differentiation or variation with respect to that field. We apply Legendre transformation to this system, and find that the resultant Hamitonian density is identical to the energy density, up to an irrelevant divergence term.

In recent years, artificial neural networks (ANNs) have won numerous contests in pattern recognition, machine learning, and artificial intelligence. The basic unit of an ANN is to mimic neurons in the brain. Neuron in ANNs is expressed as f (wx+b) or f (wx). This structure does not consider the information processing capabilities of dendrites. However, recently, studies shown that dendrites participate in pre-calculation in the brain. Concretely, biological dendrites play a role in the pre-processing to the interaction information of input data. Therefore, it is time to perfect the neuron of the neural network. This paper, add dendrite processing section, presents a novel artificial neuron, according to our previous studies (CR-PNN or Gang transform). The dendrite processing section can be expressed as . Because I perfected the basic unit of ANNs— neuron, there are so many networks to try. This article gives the basic architecture for reference in future research.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

The issue of monitoring and early warning of rock instability has received increasing critical attention in the study of rock engineering. To investigate the damage evolution process of granite under triaxial compression tests, acoustic emission (AE) tests were performed simultaneously. This study firstly introduced two novel parameters, i.e., the coefficient of variation (CoV) of the information entropy and correlation dimension of the amplitude data from the AE tests, to identify the precursor of the failure of granite. Then the relationship between the changes in these parameters and the stress-time curve was compared and analyzed. The results of this study show that: (1) There is a strong correlation between the CoV of the information entropy and the failure process of granite. The granite failed when the CoV curve raised to a plateau. (2) The fluctuation of the correlation dimension indicates the different stages of the loading process, i.e., the initial compaction stage, the linear elastic stage, the yield stage, and the failure stage. Each stage contains a descending and a rising process in the correlation dimension curve, which indicates that this parameter could be used to identify the precursor of the failure as well. (3) The combined analysis of the two can improve the accuracy of rock instability prediction. This study provides new insights into the prediction of rock instability, which has theoretical implications for the stability of subsurface engineering rock masses.

Pyrochlore group minerals are the main raw phases in granitic rocks of the Katugin complex-ore deposit that stores Nb, Ta, Y, REE, U, Th, Zr, and cryolite. They are of three main generations: primary magmatic (I), early postmagmatic (II), and supergene (III) pyrochlores. The primary magmatic phase (generation I) is fluornatropyrochlore with high concentrations of Na2O (to 10.5 wt.%), F (to 5.4 wt.%) and REE2O3 (to 17.1 wt.%) but low CaO (0.6-4.3 wt.%), UO2 (to 2.6 wt.%), ThO2 (to 1.8 wt.%), and PbO (to 1.4 wt.%). Pyrochlore of this type is very rare in nature and limited to a few occurrences, such as rare-metal deposits of Nechalacho in syenite and nepheline syenite (Canada) and Mariupol in nepheline syenite (Ukraine). It may have crystallized synchronously with or slightly later than melanocratic minerals (aegirine, biotite, and arfvedsonite) at the late magmatic stage when Fe from the melt became bound making impossible the formation of columbite. Second generation pyrochlore formed at the early postmagmatic stage of the Katugin deposit. It differs from that of first generation in lower Na2O concentrations (2.8 wt.%), relatively low F (4 wt.%), and les occupancy of the A and Y sites at similar contents of other components. Generation III pyrochlore is a product of supergene alteration processes. It is compositionally heterogeneous and contains K, Ba, Pb, Fe, and significant Si concentrations but low Na and F. Its compositions mostly fall within the filed of hydro- and kenopyrochlore.

The cutter structure and layout scheme of PDC (Polycrystalline Diamond Compact) bits are important factors in improving efficiency. To further improve the drilling efficiency of PDC bits, axe, triangular prism, and cylindrical PDC cutters were used as research objects. Based on the measured granite data, a finite element model of non-homogeneous granite was established and verified by uniaxial compression simulation. The rock-breaking process of different cutter combination schemes was compared using the finite element method, and the parameters in the best scheme were optimized using the Box-Behnken response surface method. The results show that the constructed model of non-homogeneous granite is consistent with the stress-strain relationship of real granite and is reliable. The axe PDC cutter is more aggressive than the other two cutters and is more suitable for the front row of the bit blade tooth arrangement, while the triangular prism cutter is the second most aggressive and is suitable for the rear row of tooth arrangement, and the best combination scheme is the front row of axe cutter and the rear row of triangular prism cutter arranged alternately with the axe cutter. The optimal transverse and longitudinal distances of the optimized triangular prism cutter from the front axe cutter are 10mm and 7mm, and the optimal transverse and longitudinal distances of the rear axe cutter from the front cutter are 10.06mm and 7mm. The drilling speed is more stable during drilling and the PDC bit with mixed tooth arrangement has 16.8% and 16.6% higher rate of penetration(ROP) compared with the bit with single axe cutter and triangular prism cutter, and the drilling speed is more stable during working, which can effectively improve the rock breaking efficiency of the PDC bit. The field application proves that the bit with mixed cutter arrangement is easier to break the complex formations, with more stable ROP and better efficiency. The study can provide theoretical support for the cutter layout of the PDC bit.

Orbit and clock products are used in real-time GNSS precise point positioning without knowing their quality. This study develops a new approach to detect orbit and clock errors through comparing geometry-free and geometry-based wide-lane ambiguities in PPP model. The reparameterization and estimation procedures of the geometry-free and geometry-based ambiguities are described in detail. The effects of orbit and clock errors on ambiguities are given in analytical expressions. The numerical similarity and differences of geometry-free and geometry-based wide-lane ambiguities are analyzed using different orbit and clock products. Furthermore, two types of typical errors in orbit and clock are simulated and their effects on wide-lane ambiguities are numerically produced and analyzed. The contribution discloses that the geometry-free and geometry-based wide-lane ambiguities are equivalent in terms of their formal errors. Although they are very close in terms of their estimates when the used orbit and clock for geometry-based ambiguities are precise enough, they are not the same, in particular, in the case that the used orbit and clock, as a combination, contain significant errors. It is discovered that the discrepancies of geometry-free and geometry-based wide-lane ambiguities are coincided with the actual time-variant errors in the used orbit and clock at the line-of-sight direction. This provides a quality index for real-time users to detect the errors in real-time orbit and clock products, which potentially improves the accuracy of positioning.

The aim of this investigation is focused on the effects of hooked-end steel fibers on both fresh and hardened properties of modified self-compacting concretes (SCC). For this purpose, the steel fibers are associated with other residues contents (i.e. marble, granite and rubber). This concatenated materials contents constitutes a novelty since no investigations are reported. It is found that the increase of rubber content, a better ability to absorb energy is observed. This indicates that a good alternative of structural material is provided. Fresh properties are evaluated by using flow, T500 time, V-funnel, J-ring methods. The mechanical behavior is evaluated in terms of compressive strength, tensile strength, static and dynamic modulus of elasticity, and damping ratio. Experimental results of the water absorption, porosity and density are also attained. It is also found that a SCC mixture containing steel fiber, marble/granite residue and rubber content is a potential mixture to be considered when in SCC designing associated with improved damping ratio. Although the rubber content decreases the mechanical behavior and slump flow, the concatenated utilization of MGR and steel fiber contents provide a slight improve in the damping result. An environmental benefit can also be associated since the cement consumption is decreased with marble additions.

Understanding the thermal cracks of rock caused by high temperature is of great help to the development of underground engineering, such as geothermal mining, underground coal gasification. Although there has been many study on thermal cracking, it is not systematic and in-depth enough. In order to deeply study the thermal crack mechanism of rock, this paper conducted thermal cracking experiments on granite at different temperatures and heating/cooling paths, and qualitative and quantitative analysis was conducted on the crack initiation characteristics, propagation paths, and crack network morphology of rock thermal crack under different test conditions. The thermal crack mechanism was also analyzed from the perspectives of mineral petrology, fracture mechanics, thermodynamics, and other aspects. The research results show that there are two obvious mutation points in the study temperature range for samples with fast cooling paths (SF path: slow heating and fast cooling; FF path: fast heating and fast cooling), around 200-300 ℃ and 600 ℃, respectively, while for samples with slow cooling paths (SS path: slow heating and slow cooling; FS path: fast heating and slow cooling), there is only one mutation point around 600 ℃. The initiation positions of thermal cracking under all temperature paths are relatively similar, with intergranular crack located between particles at the edge of the sample or intercrystalline crack in the middle of feldspar or quartz aggregates. The initiation temperature of SF and FF path specimens is relatively low compared to SS and FS path specimens, and the number and size of cracks is small. The crack network structure formed by the SF path is the most complex, with the largest crack ratio and cumulative crack length; The crack network structure formed by the FF path is relatively complex, with a larger main crack size but relatively fewer secondary cracks; The FS and SS paths do not form a complex network with good connectivity. The process of thermal crack development can be divided into three stages: the development of small cracks, the joint development of main cracks and small cracks, and the connection of cracks into a network structure. The mechanism of thermal crack propagation is that the expansion and thermal conductivity between different crystals are different. The thermal stress caused by temperature gradient and the tension or shear stress caused by the inconsistent deformation of crystals form stress concentration in weak areas such as particles boundary, cleavage, and original cracks. Firstly, it causes some crystals with smaller strength or less rounded shape to crack, and when the combined stress is large, the cracks will gradually expand along the existing fine cracks. This also explains that the most main cracks of the SF and FF path specimens mainly surround some large mineral aggregates or between particles.

We previously described spherical crystals in minerals from prismatine-bearing rock from Waldheim, including ultrahigh-pressure (UHP) minerals such as stishovite and coesite, in uncommon crustal environments. To determine if this was an outlier phenomenon, we searched for equivalent inclusions in other rocks, which we indeed discovered in a Variscan tin granite sensu stricto from the Erzgebirge. The identification of more examples of this phenomenon implies a novel, very rapid transcrustal transport mechanism, which however is not unique. We demonstrate the unusual occurrence of UHP minerals (moissanite, diamond, lonsdaleite, stishovite, coesite, kumdykolite, and cristobalite-II) in topaz of granitic rocks, which reflects the direct interaction of mantle and crust via supercritical fluids or extremely volatile-rich melts. Most UHP minerals are tiny inclusions in moissanite. The trapping by this mineral prevents a fast reaction in an extraneous environment.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

The detection accuracy of bridge superficial defect using the deep neural network approach decreases significantly under light variation and weak texture condition. To address these issues, an enhanced intelligent detection method based on the YOLOv8 deep neural network is proposed in this study. Firstly, multi-branch coordinate attention (MBCA) is proposed to improve the accuracy of coordinate positioning by introducing a global perception module in coordinate attention mechanism. Furthermore, a deformable convolution based on MBCA is developed to improve the adaptability for complex feature shapes. Lastly, the deformable convolutional network-attention-YOLO (DAC-YOLO) detection algorithm is formed by replacing the deep C2F structure in the YOLOv8 architecture with deformable convolution. A supervised dataset consisting of 4794 bridge surface damage images is employed to verify the proposed method, and results show that it achieves improvements of 2.0% and 3.4% in mAP and R. Meanwhile, the model complexity decreases by 1.2G, increasing the detection speed by 3.5/f·s-1.

Recent years have witnessed a rapid growth of code-reuse attacks in advance persistent threats and cyberspace crimes. Carefully crafted code-reuse exploits circumvent modern protection mechanisms and hijack the execution flow of a program to perform expected functionalities by chaining together existing codes. The sophistication and intrication of code-reuse exploits hinder the scrutinization and dissection on them. Although the previous literature has introduced some feasible approaches, effectiveness and reliability in practical applications remain severe challenges. To address this issue, we propose Horus, a data-driven framework for effective and reliable detection on code-reuse exploits. In order to raise the effectiveness against underlying noises, we comprehensively leverage the strengths of time-series and frequency-domain analysis, and propose a learning-based detector that synthesizes the contemporary twofold features. Then we employ a lightweight interpreter to speculatively and tentatively translate the suspicious bytes to open the black box and enhance the reliability and interpretability. Additionally, a functionality-preserving data augmentation is adopted to increase the diversity of limited training data and raise the generality for real-world deployment. Comparative experiments and ablation studies are conducted on a dataset composed of real-world instances to verify and prove the prevalence of Horus. The experimental results illustrate that Horus outperform existing methods on the identification of code-reuse exploits from data stream with an acceptable overhead. Horus does not rely on any dynamic executions and can be easily integrated into existing defense systems. Moreover, Horus is able to provide tentative interpretations about attack semantics irrespective of target program, which further improve system's effectiveness and reliability.

In the paper, a fully discrete compact difference scheme with $O(\tau^{2}+h^{4})$ precision is established by considering the numerical approximation of the one-dimensional Allen-Cahn equation. The numerical solutions satisfy discrete maximum principle under reasonable step ratio and time step constraint is proved. And the energy stability for the fully discrete scheme is investigated. An example is finally presented to show the effectiveness of scheme.

The semantic segmentation of high-resolution remote sensing images (HR-RSI) is crucial for a wide range of applications, such as precision agriculture, urban planning, natural resource assessment, and ecological monitoring. However, accurately classifying pixels in HR-RSI faces challenges due to densely distributed small objects and scale variations. Existing techniques, including Convolutional Neural Networks (CNNs) and other methods for hierarchical feature extraction and fusion of remote sensing image, often do not achieve the desired accuracy. In this paper, we propose a novel approach called the Hierarchical Rich-scale Fusion Network (HRFNet) to address these challenges. HRFNet utilizes advanced information rating and image partition techniques to extract rich-scale features within image layers. This allows for the adaptive exploration of both local and global contextual information. Moreover, we introduce a structured intra-layer to inter-layer feature aggregation module, which enables the adaptive extraction of fine-grained details and high-level semantic information from multi-layer feature maps in a highly flexible manner. Extensive experimentation has been conducted to validate the effectiveness of our proposed method. Our results demonstrate that HRFNet outperforms existing techniques, achieving state-of-the-art (SOTA) results on benchmark datasets, specifically the ISPRS Potsdam and Vaihingen datasets.

The critical period (CP) phenomenon in language development ranks among the 125 conundrums facing scientists in the 21st century, according to Science. While the phenomenon itself has been noncontroversial in first language acquisition, it still warrants an adequate explanation. Predicated on language acquisition as a complex process, questions among the first to be raised include: How do children accomplish this remarkable feat in such a short amount of time? And how do nature and nurture come together to influence language learning? In second language acquisition, however, both the notion of CP, albeit popular, and its empirical evidence have remained contested to this date - among the questions, whether the observed evidence counts as CP-specific and/or whether or not it warrants an isomorphic attribution to maturational constraints. Entwined in this debate are two well-established facets of inter-learner differential attainment. The first is that there exists a stark difference in ultimate attainment between younger and older learners. A second facet is the vast differences in ultimate attainment among older learners. In this article, adopting a social physics approach, we mathematically establish both the relationship between nature and nurture contributions and the presence of a critical period, and, at once, tender a parsimonious and probable theory for the twin phenomena of inter-learner differential attainment.

A practical method is presented to estimate rare earth elements (REE) concentrations in magmatic vapour phase (MVP) in equilibrium with water-saturated granitic melts based on empirical fluid-melt partition coefficients of REE (k_P^REE). The values of k_P^REEcan be calculated from a set of new polynomial equations linking to the chlorine molality (m_Cl^v) of the MVP associated with granitic melts, which are established via a statistical analysis on the existing experimental dataset. These equations may be applied to the entire pressure range (0.1 to 10.0 kb) within the continental crust, suggesting that light REEs behave differently in magmatic fluids, i.e. either being fluid compatible with higher m_Cl^v or fluid incompatible with lower m_Cl^v values. In contrast, heavy REEs are exclusively fluid incompatible and partition favourably into granitic melts. Consequently, magmatic fluids tend to be rich in LREE relative to HREE, leading to REE fractionation during the evolution of magmatic hydrothermal systems. Maximum k_P^REEvalue for each element is predicted and presented in a REE distribution diagram constrained by the threshold of m_Cl^v. REE contents of the granitic melt is approximated by whole-rock analysis, so that REE concentrations in the associated MVP would be estimated from the value of k_P^REE given chemical equilibrium retains. Two examples are provided respectively, to show the use of this method as a REE tracer to fingerprint the source of ore-fluids responsible for the Lake George intrusion-related Au-Sb deposit in New Brunswick (Canada), and for the Bakircay Cu-Au (-Mo) porphyry systems in northern Turkey.

For the task planning problem of the command and control architecture, the existing algorithms have problems such as low efficiency and poor re-planning quality under abnormal conditions. Based on the requirements of the current accusation architecture, this paper constructs a distributed command and control architecture model based on multi-agents, which makes use of the superiority of multi-agents in dealing with complex tasks. The concept of MultiAgents-HTN is proposed under the framework. The original hierarchical task network planning algorithm is optimized, the multi-agent collaboration framework is redefined, and the coordination mechanism of local conflict is designed. Taking the classical resource scheduling problem as the experimental background, the comparison between the proposed algorithm and the classical HTN algorithm is carried out. The experimental results show that the proposed algorithm has higher quality and higher efficiency than the existing algorithm, and the space anomaly is heavy during processing. The planning is more efficient, and the time is more complicated and superior in dealing with the same problem, with good convergence and adaptability. The conclusion proves that the distributed command and control architecture proposed in this paper has high practicability in related fields and can solve the problem of distributed command and control architecture in multi-agent environment.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

In this paper, we study the fractional pseudo-parabolic equations u_t + (−△)^s u + (−△)^s u_t = u log |u|. Firstly, we recall the relationship between the fractional Laplace operator (−△)^s and the fractional Sobolev space H^s and discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence of global weak solution: for the low initial energy J(u₀) < d, the solution is global in time with I(u₀) > 0 or ∥u₀∥X_0(Ω) = 0 and blows up +∞ with I(u₀) < 0; for the critical initial energy J(u₀) = d, the solution is global in time with I(u₀) ≥ 0 and blows up at +∞ with I(u₀) < 0. The decay estimate of the energy functional for the global solution is also given.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

We proposed a novel concept of flight time matrix (FTM). In this work, the proposed FTM was verified first numerically. The numerical simulation revealed perfect results which showed that FTM can be used to assist the nondestructive evaluation of ballistic armor plates using acousto-ultrasonics. Two donated commercial ballistic armor plates were sought for a case study where artificial defects were prepared. The results of FTM were reasonably well. The artificial defects were clearly identifiable in one directional location array and FTM contour graphs. More comprehensive superimpositions of flight time vs location and FTM contour plots can be advanced to a better visualization of the defect presence. The resolution of FTM method is in the range of submillimeter or less. This study demonstrated that AU (acousto-ultrasonics) technique is a field applicable and yet reliable tool for inspection of the hidden defects in body armors. A broader merit of the proposed FTM algorithm is that it may promote the development of specific tools/device for nondestructive evaluations field.

Non-destructive testing is an emerging need in manufacturing processes and in service of ballis-tic armor plates. It has been shown that acoustic emission and ultrasonics are among the most applicable techniques. However, these techniques often require relative sophisticated processing and strong tech background for the evaluators. The purpose of the present work is to develop a flight time based algorithm and to demonstrate this algorithm using commercial multilayered armor plates. We proposed a novel concept of flight time matrix (FTM). In this work, the proposed FTM was verified first numerically. The numerical simulation revealed perfect results which showed that FTM can be used to assist the nondestructive evaluation of ballistic armor plates using acous-to-ultrasonics. Two donated commercial ballistic armor plates were sought for a case study where artificial defects were prepared. The results of FTM were reasonably well. The artificial defects were clearly identifiable in one directional location array and FTM contour graphs. More com-prehensive superimpositions of flight time vs location and FTM contour plots can be advanced to a better visualization of the defect presence. The resolution of FTM method is in the range of submillimeter or less. This study demonstrated that AU (acousto-ultrasonics) technique is a field applicable and yet reliable tool for inspection of the hidden defects in body armors. A broader merit of the proposed FTM algorithm is that it may promote the development of specific tools/device for nondestructive evaluations field.

To detect aberrant human behaviors from large volume of passive data collected by smartphones in real time, we propose an online anomaly detection method using Hotelling’s T-squared test. The test statistic is a weighted average, with more weight on the between-individual component when there are little data available for the individual and more weight on the within-individual component when the data are adequate. The algorithm takes only O(1) run time in each update and the required memory usage is fixed after a pre-specified number of updates. The performance of the proposed method, in terms of accuracy, sensitivity and specificity, is consistently better than or equal to the offline method that it builds upon depending on the sample size of the individual data.

Abstract Several studies have been conducted to strengthen weak road layers, regardless of whether they are un-der construction or are undergoing maintenance. Using substrates filled with different materials has proven effective for increasing the strength of these layers. In this study, I evaluated the coefficient of lateral soil pressure under various conditions when using reinforced and unreinforced piles filled with in-expensive material and the extent of their contribution to strengthening road layers. The results con-firmed that there was a difference in the coefficient of lateral soil pressure when the sand-filled piles were reinforced. The sand-filled piles were divided into several parts by arming. The maximum coeffi-cient of lateral soil pressure was 0.38 in the case of sand (1 mm) with reinforcement, whereas it was 0.29 in the same case without reinforcement as shown in Figure 1. The maximum coefficient of lateral soil pressure was 0.27 in the case of granite grain (2 mm) with reinforcement, whereas it was 0.17 in the same case without reinforcement. Moreover, the maximum lateral pressure coefficient was 0.26 in the case of granite grain (3 mm) with reinforcement, and it was 0.30 in the same case without reinforce-ment.

This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

The combined heat and power system is based on the principle of "cascade utilization of thermal energy" for system integration and optimization. The rational utilization of energy, as well as the rational arrangement of energy flow and the process optimization combination of the overall system are taken into account in order to achieve multifunctional goals in the field of thermal engineering. The present paper presents a detailed assessment of combined heat and power systems from above standpoints. This article is divided into two parts “CHP based on thermo-dynamic cycles” and “CHP based on non-thermodynamic cycles”. Each part is then classified based on power subsystem energy consumption efficiency (high or low), including Rankine cycle, ORC, Stirling cycle, gas turbine, reciprocating engine, PVT and fuel cell. The present paper also helps identify the research gaps in this area and provides direction on future studies on combined heat and power systems.

Pregnancy at advanced maternal age is considered a risk factor for adverse maternal, fetal, and neonatal outcomes. Here we investigated whether maternal age could be associated with differences in the blood levels of newborn screening (NBS) markers for inborn metabolic disorders on the Recommended Universal Screening Panel (RUSP). Population-level NBS data from screen-negative singleton infants were examined, which included blood metabolic markers and covariates such as gestational age, birth weight, age at blood collection, infant sex, parent-reported ethnicity, and maternal age at delivery. Marker levels were compared between maternal age groups (age range: 15-44 years) using effect size analyses, which controlled for group size differences and potential confounding from other covariates. Our results showed that 13% of the markers had maternal age-related differences including newborn metabolites with either increased (C14, C16, C18, C18:1, C3DC) or decreased (C5OH) levels at advanced maternal age group (≥35 years, absolute Cohen’s d ≥ 0.2). The increased C3DC levels in this group correlated with a higher false-positive rate in newborn screening for malonic acidemia (p-value < 0.001), while no significant difference in screening performance was seen for other markers. Maternal age at delivery is associated with inborn metabolic differences and should be considered together with other clinical variables in genetic disease screening.

For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear based on permutation entropy of Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN) Adaptive Neuro-fuzzy Inference System (ANFIS) in this paper. The original signal is decomposed into 6 intrinsic mode functions (IMF) and residual components by CEEMDAN. Since the IMF contains the main characteristic information of planetary gear faults, time complexity of IMFs are reflected by permutation entropies to quantify the fault features. The permutation entropies of each IMF component are defined as the input of ANFIS, and its parameters and membership functions are adaptively adjusted according to training samples. Finally, the fuzzy inference rules are determined, and the optimal ANFIS is obtained. The overall recognition rate of the test sample used for ANFIS is 90.75%, and the recognition rate of gear with one missing tooth is relatively high. The recognition rates of different fault gears based on the method can also achieve better results. Therefore, the proposed method can be applied to planetary gear fault diagnosis effectively.

During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

Auto checkout has received more and more attention in recent years and this system automatically generates a shopping bill by identifying the picture of the products purchased by the customers. However, the system is challenged by the domain adaptation problem, where each image of the training set contains only one commodity, whereas the test set is a collection of multiple commodities. The existing solution to this problem is to resynthesize the training images to enhance the training set. Then the composite images are rendered using CycleGAN to make the image distribution of the training set and the test set more similar. However, we find that the detection boxes given by the ground truth of the common dataset contain a large part of the background area, the area will affect the training process as noise. To solve this problem, we propose a mask data priming method. Specifically, we redo the large scale Retail Product Checkout (RPC) dataset and add segmentation annotation information to each item in the training set image based on the original dataset using pixel-level annotation. Secondly, a new network structure is proposed in which we train the network using joint learning of detectors and counters, and fine-tune the detection network by filtering out suitable images from the test set. Experiments on the RPC dataset have shown that our method yields better results. we used an approach that reached 81.87% compared to 56.68% for the baseline approach which demonstrates that pixel-level information helps to improve the detection results of the network.

Critically ill patients with COVID-19 may develop serious respiratory difficulties, causing a significant reduction in blood oxygen saturation pressure. Physical Ventilation of the lungs is one of the main methods to help critically ill patients through the acute phase of infection. During extreme situations when dysfunctional lungs are filled with sticky sputum in the alveolus or when there are simply not enough ventilators to match the need, the mortality rate can be dramatically increased. Here, we propose an intravenous injection method that may increase and maintain the blood oxygen pressure at normal levels. The intravenous (IV) infusion contains oxygen nanobubbles in physiological saline solution (ONPS), in which the dissolved oxygen content can be 2-6 times higher than the normal oxygen solubility in pure water. This makes it possible to oxygenate blood with a small limited volume of IV fluid without the risk of gaseous bubble formation in blood vessels.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

To explore the relevant factors that affect the efficacy of consciousness-regaining therapy (CRT)for prolonged disorder of consciousness(pDOC),a retrospective analysis was conducted on the case data of 114 patients with pDOC admitted to department of functional neurosurgery of Tianjin Huanhu Hospital from January 2019 to January 2022. Basic information on the cases,data on pDOC disease assessment, consciousness-regaining therapy methods, and efficacy evaluation were collected. A total of 114 patients were grouped and compared based on the efficacy at the end of treatment. Among them, there were 61 cases in the ineffective group and 53 cases in the effective group. There was no statistically significant difference (P&gt;0.05) between the two groups in terms of gender, age, etiology, acute cerebral herniation, emergency craniotomy surgery, emergency decompressive craniectomy, time from onset to start of consciousness-regaining therapy , and duration of consciousness-regaining therapy(P&gt;0.05). However, there were statistically significant differences (P&lt;0.05) in terms of secondary hydrocephalus, , consciousness-regaining therapy methods, CRS-R grading before treatment, and GOSE score at 6 months after treatment. Binary logistic regression analysis showed that the type of therapy (OR=0.169, 95% CI: 0.057-0.508) was a related factor affecting the efficacy of consciousness-regaining therapy (P&lt;0.05).Compared with non-invasive therapy, personalized awakening therapy using various invasive consciousness-regaining therapy methods can help improve the efficacy of therapy for pDOC.

In recent years, the emergence of spatiotemporal big data has made the transition of functional identification from the physical dimension to socioeconomic or human activities becoming more common. In the identification of urban functional areas, most studies considered only a single data source and a single division scale, the research results have problems such as low update frequency or incomplete information in a single data set, and overfitting or underfitting in a single spatial resolution. Using taxi trajectory data and point of interest (POI) data as the main data source, this study proposes a multi-scale recursive identification method for urban functional areas based on cross-validation. First, used the dynamic time warping (DTW) algorithm generates a time series similarity matrix, the CA-RFM model combines the clustering algorithm and random forest model is constructed, the model uses a clustering algorithm (K-MEDOIDS) to extract sig-nificant feature regions as input, which are imported into the random forest model for UFZ identification. Then, to overcome the shortcomings of single scale in expressing urban structural characteristics, a recursive model of different levels of urban road networks is established to classify multi-scale functional areas. Finally, cross-validation using the CA-RFM model and POI quantitative identification method, obtains the final identification results of urban functional areas. This paper selects Shenzhen as the study area for the case study, the results show that the com-bination of clustering algorithm and random forest model greatly reduces the error of manual selection of training samples. In addition, the research shows the superiority of the multi-scale recursive identification method that fuses multi-source data and performs cross-validation from two aspects, that is, the division speed of urban functional area identification results is accelerated and the accuracy is improved.

This study employs the phase-field regularized cohesion model (PF-CZM) to simulate crack propagation and damage behavior in porous granite. We investigate how pore radius (r), initial crack-pore distance (D), and pore-crack angle (θ) impact crack propagation. The simulation findings reveal that, with a fixed deflection angle and initial crack-pore distance, larger pores are more likely to induce crack extension under identical loading conditions. Moreover, with r and θ keeping constant, the crack extension can be divided into two stages: from its initiation to the lower edge of the pore and then from the lower edge to the upper boundary of the model. By varying the values of D and r, we derive multiple combinations of different D/r ratios and pore radii. These results demonstrate that with constant r, cracks tend to deflect toward the pore closer to the initial crack. Conversely, when D is maintained constant, cracks will preferentially deflect toward pores with a larger r. In summary, the numerical simulation of rock pores and initial cracks, based on the PF-CZM, exhibits remarkable predictive capabilities and holds significant potential in advancing rock fracture analysis.

Extreme-mass-ratio inspirals (EMRIs) are significant observational targets for spaceborne gravitational wave detectors, namely, LISA, Taiji, and Tianqin, which involve the inspiral of stellar-mass compact objects into massive black holes with a mass range of approximately 104∼107M⊙. EMRIs are estimated to produce long lived gravitational wave signals with more than 105 cycles before plunge, making them an ideal laboratory for exploring the strong-gravity properties of the spacetimes around the MBHs, stellar dynamics in galactic nuclei, and properties of the MBHs itself. However, the complexity of the waveform model, which involves the superposition of multiple harmonics, as well as the high-dimensional and large-volume parameter space, make the fully coherent search challenging. In our previous work, we proposed a 10-dimensional search using Particle Swarm Optimization (PSO) with local maximization over the three initial angles. In this study, we extend the search to an 8-dimensional PSO with local maximization over both the three initial angles and the angles of spin direction of the MBH where the latter contribute a time independent amplitude to the waveforms. Additionally we propose a 7-dimensional PSO search by using a fiducial value for the initial orbital frequency and shifting the corresponding 8-dimensional Time Delay Interferometry responses until a certain lag returns the corresponding 8-dimensional log-likelihood ratio maximum. The reduced dimensionality likelihoods enable us to successfully search for EMRI signals with duration of 0.5 years and signal-to-noise ratio of 50 within a wider search range than our previous study. We discuss further developments, such as using a hierarchical search to narrow down the search ranges of certain parameters, and applying Graphics Processing Units to speed up the code. These advances aim to improve the efficiency and accuracy of the EMRI search algorithm.

Diffuse cavernous hemangioma of the rectum (DCHR) is a rare benign lesion of vascular malformation. According to previous studies, the most reported major symptoms of DCHR are recurrent painless rectal bleeding or iron deficiency anemia[1][2][3][4][5][6]. We present a case of an 8Y11M boy who was diagnosed with DCHR by MRI. The patient underwent Laparoscopic-assisted transanal distal sigmoidectomy and sigmoido-anal anastomosis（Laparoscopic Swenson Procedure）, and recovered well. After the operation, the child had short-term fecal incontinence and loose stools, which returned to normal after half a year. Regardless of age and symptoms, early and correct diagnosis and treatment of DCHR and postoperative restoration of normal anal function are necessary. Laparoscopic Swenson procedure may be a good option for the treatment of DCHR.

In the environments of all kinds open coal storage sites , mining-affected coalbeds, and goafs, parts of coal body at low moisture content (≤8%) are prone to spontaneous combustion under the influence of some external environmental factors. In order to examine the influence effect of low moisture content on the spontaneous combustion tendency of coals with different metamorphic grade, we conducted temperature programmed oxidation (TPO) experiment and differential scanning calorimetry (DSC) experiment to study the spontaneous combustion characteristics of coals with different metamorphic grade at four different low moisture content, and comparatively analyzed the change laws of the characteristic parameters of four different metamorphic grade coals at four different low moisture content. The experimental results indicate that: 1) Compared other low moisture content, anthracite and fat coal at low moisture content of 1.2% show stronger tendency to undergo spontaneous combustion, long flame coal and lignite at low moisture content of 3.4% and 5.6% are more prone to spontaneous combustion. 2) Four different metamorphic grade coals at low moisture content of 7.8% are less prone to spontaneous combustion; 3) Coals with different metamorphic grade have different tendency to undergo spontaneous combustion.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

The vibration signal of the engine contains strong background noise and many kinds of modulating components, which is difficult to diagnose. Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). VMD can effectively avoid endpoint effect and modal aliasing. However, VMD cannot effectively eliminate the random noise in the signal, so the random decrement technique is introduced to solve the problem. Based on the crankshaft bearing fault simulation experiment, the four kinds of wear state vibration signals are decomposed by VMD, and the modal components with smaller permutation entropy are selected as fault components. Then the fault component is processed by the random decrement technique, and the Hilbert envelope spectrum of the fault component is obtained. Compared with the fault feature extraction method based on EMD and EEMD, the feature extraction results of the proposed method are better than those of the above two methods. The simulation analysis and the simulation test of the crankshaft bearing fault verify the effectiveness of the proposed method.

Post-training quantization is pivotal in deploying convolutional neural networks for mobile applications. Block-wise reconstruction with adaptive rounding, as employed in prior works like BrecQ and Qdrop, facilitates acceptable 4-bit quantization accuracy. However, adaptive rounding is time-intensive, and its constraint on weight optimization space curtails the potential for quantization performance. The optimality of block-wise reconstruction hinges on the quantization status of subsequent network blocks. In this investigation, we delve into the theoretical underpinnings of the limitations inherent in adaptive rounding and block-wise reconstruction. Our exploration leads to the development of a post-training quantization methodology, designated as AE-Qdrop. This algorithm operates in two distinct phases: block-wise reconstruction and global fine-tuning. The block-wise reconstruction phase introduces a progressive optimization strategy, superseding adaptive rounding, which not only augments quantization precision but also significantly improves quantization efficiency. To mitigate the risk of overfitting, we introduce a random weighted quantized activation mechanism. During the global fine-tuning phase, we account for interdependencies among quantized network blocks. The weight of each network block will be corrected with logit matching and feature matching. Extensive experiments validate that AE-Qdrop achieves high-precision and efficient quantization. For instance, in the case of 2-bit MobileNetV2, AE-Qdrop outperforms Qdrop by achieving a 6.26% enhancement in quantization accuracy and quintupling the quantization efficiency.

In this paper, PEN3 electronic nose was used to detect and recognize fresh and moldy apples (inoculated with Penicillium expansum and Aspergillusniger) taken Golden Delicious apples as model subject. Firstly, the apples were divided into two groups: apples only inoculated with different molds (Group A) and mixed apples of inoculated apples with fresh apples (Group B). Then the characteristic gas sensors of the PEN3 electronic nose that were most closely correlated with the flavor information of the moldy apples were optimized and determined, which can simplify the analysis process and improve the accuracy of results. Four pattern recognition methods, including linear discriminant analysis (LDA), backpropagation neural network (BPNN), support vector machines (SVM) and radial basis function neural network (RBFNN), were then applied to analyze the data obtained from the characteristic sensors, respectively, aiming at establishing the prediction model of flavor information and fresh/moldy apples. The results showed that only the gas sensors of W1S, W2S, W5S, W1W and W2W in the PEN3 electronic nose exhibited strong signal response to the flavor information, indicating were most closely correlated with the characteristic flavor of apples and thus the data obtained from these characteristic sensors was used for modeling. The results of the four pattern recognition methods showed that BPNN presented the best prediction performance for the training and validation sets for both the Group A and Group B, with prediction accuracies of 96.29% and 90.00% (Group A), 77.70% and 72.00% (Group B), respectively. Therefore, it first demonstrated that PEN3 electronic nose can not only effectively detect and recognize the fresh and moldy apples, but also can distinguish apples inoculated with different molds.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Primary urethral malignancies are rare in clinical practice and elderly female are prone to suffer. The cause of PUC is unknown and may be related to long-term chronic inflammation, infection, sexual intercourse, pregnancy and irritation of the urethra. Incipient symptom of PUC is not distinctness and can easily lead to misdiagnosis. The final diagnosis relied on transvaginal ultrasound-guided mass biopsy and urethral biopsy. Early tumor treatment is mainly based on surgical resection. For advanced tumors, it is recommended to adopt a comprehensive treatment plan combining surgery, radiotherapy and chemotherapy We report this case with the aim of bringing attention to that primary urethral cancer progresses rapidly and has a poor prognosis, it is urged to call for a need of diagnostic and treatment specification.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

An energy model that correlates fan airflow, head, speed, and system power input is essential to detect device faults and optimize control strategies in fan systems. Since the application of variable frequency drives (VFDs) makes the motor efficiency data published by manufacturers inapplicable, the fan efficiency and drive (belt-motor-VFD) efficiency must be identified for each individual system to obtain accurate energy models. The objectives of this paper are to identify an energy model of existing VFD-motor-fan systems using available experimental data and demonstrate its applications in loose belt fault detection and virtual airflow meter development for optimal control. First, an approach is developed to identify the fan head, fan efficiency and drive efficiency curves using available fan head, speed, and system power input as well as temporarily measured airflow rate without measuring shaft power. Then the energy model is identified for an existing VFD-motor-fan system. Finally, the identified model is applied to detect the slipped belt faults and develop the virtual airflow meter. The experiment results reveal that the developed approach can effectively obtain the energy model of VFD-motor-fan systems and the model can be applied to effectively detect slipped belt faults and accurately calculate the fan airflow rate.

This study investigated the influence and interaction of tobacco promotional and control information with adolescents’ current smoking and smoking susceptibility. 12,278 students were recruited from junior, senior and vocational high schools located in Shanghai, China. The exposure to tobacco promotional and control message of participants over the past 30 days were examined, as well as current smoking and never smokers’ initiation susceptibility. Complex sample analysis was applied. Descriptive and multivariate logistic regressions were conducted. 89.3% and 91.5% of adolescents investigated were exposed to tobacco promotional and control message respectively, which separately increased and decreased the risk of current smoking and never-smokers’ smoking susceptibility, especially among males and junior high school students. The risk changed in consistency with the exposure level（P_trend < 0.001）. Tobacco control message seemed to mitigate the influence of tobacco promotions in the risk of both current smoking (OR = 0.64, 95%CI: 0.41–0.99) and smoking susceptibility (OR = 0.65, 95%CI: 0.46–0.93). Tobacco-related message exposure was highly prevalent and associated with youth smoking risk and smoking susceptibility. It is important to enhance the comprehensiveness and enforcement of promotion bans. Given the improvement of tobacco control message on smoking risk brought by tobacco promotions, the publicity and dissemination of tobacco control information need to be consistently strengthened.

The studied Khanbogd pluton of peralkaline granite is located in southern Mongolia and occupies an area of ~1000 sq. km. Previously, two ring-shaped bodies were constructed in a flattened shape pluton. However, this shape was not used for the genesis of this pluton. A recent study of Landsat image showed a several elliptical intrusions in two bodies. Chemistry interpretation shows that each intrusion differs in ASI, CIPW norms, 87Sr/86Sri and δ18O isotopes. Elliptical intrusions, uplifted country rocks between them, and roof pendants suggest magma penetration along fractured country rocks. Furthermore, two adjacent intrusive bodies and undeformed host rocks at the front part of the pluton are consistent with underplating magmatic factors during duplex-type thrusting. This magma event is also supported by low of Sr, Ba, Eu and high of Th, U, Pb anomalies and a few amount of garnet crystals in the granites, implying vapor absent melt crystallization associated with underplating. Multiple melt sources, as well as from mantle and recycled sea floor rocks, are identified by ratio of 87Sr /86Sri and δ18O values. The low isotope values, the thrust nature and 295–286 Ma ages of the alkali granites, indicate an underplate magma evidenced during Permian rifting.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.

The rapid development of new retail and the impact of COVID-19 have catalyzed the blowout growth of community group purchasing. The emergence of community group purchasing collection and delivery points (CGPCDPs) has become a new way to solve the "last mile" problem of new retail delivery. Based on the point of interest (POI) data of CGPCDPs of Nansha District, Guangzhou City, this study uses text analysis, spatial analysis, model analysis, and other methods to analyze the operation mode, spatial distribution, and influencing factors of CGPCDPs. The conclusions are as follows: CGPCDPs initiators are mainly shopkeepers. They depend mainly on wholesale and retail shops. Service targets are mainly urban and rural communities, followed by industrial areas. The distribution of CGPCDPs has apparent spatial differentiation. At the macro scale, it shows the characteristics of "central agglomeration and peripheral dispersion". It is distributed along the "northwest-southeast" direction and presents a "dual-core multi-center" pattern. At meso-micro scale, different built environments in developed areas of cities, villages in the city (ChengZhongCun) and rural areas show distinct distribution patterns. The MGWR regression model has a better fitting effect than OLS and GWR. The main influencing factors are population density, construction land, house price, supporting place, residence density, urban community, and road proximity.

With global warming and accelerated degradation of permafrost, the engineering problems caused by the formation of weak zones between the shallow and permafrost layers of soil–rock mixture (S-RM) slopes in permafrost regions have become increasingly prominent. To explore the influence of rock content on the shear strength of the S-RM freezing–thawing interface, the variation in the shear strength for different rock content is studied herein using direct shear tests. In addition, a 3D laser scanner is used for obtaining the topography of the shear failure surface. Combined with the analysis results of the shear band-particle calculation model, the influence of the rock content on the shear strength of the interface is explored. It was found that the impact threshold of the rock content on the interface strength and failure mode is approximately 30%, when the rock content (R) is &gt; 30% and that the shear strength increases rapidly with increasing rock content. When R ≤ 30%, the actual shear plane is similar to waves; when R &gt; 30%, the shear plane appears as gnawing failure. The shear strength of S-RM freezing–thawing interface mainly comes from the bite force and friction between particles. The main reason for the increase in shear strength with increasing rock content is the increase in bite force between particles, which makes the ratio of bite force to friction force approximately 1:1.

Fake news detection has become a significant topic based on the fast-spreading and detrimental effects of such news. Many methods based on deep neural networks learn clues from claim content and message propagation structure or temporal information, which have been widely recognized. However, such models (i) ignore the fact that information quality is uneven in propagation, which makes semantic representations unreliable. (ii) Most models do not fully leverage spatial and temporal structure in combination. (iii) Finally, internal decision-making processes and results are non-transparent and unexplained. In this study, we develop a trust-aware evidence reasoning and spatiotemporal feature aggregation model for more interpretable and accurate fake news detection. Specifically, we first design a trust-aware evidence reasoning module to calculate the credibility of posts based on a random walk model to discover high-quality evidence. Next, from the perspective of spatiotemporal structure, we design an evidence-representation module to capture the semantic interactions granularly and enhance the reliable representation of evidence. Finally, a two-layer capsule network is designed to aggregate the implicit bias in evidence while capturing the false portions of source information in a transparent and interpretable manner. Extensive experiments on two benchmark datasets indicate that the proposed model can provide explanations for fake news detection results, as well as can achieve better performance, boosting 3.5% in F1-score on average.

In South Korea, landslides are caused by localized heavy rainfall and typhoons, which often occur in the summer season at natural slopes in mountainous areas and artificial slopes in urban surroundings. Flow-type landslides frequently occur in mountainous areas. To evaluate flow-type landslides, it is essential to identify the physical characteristics of soil, giving focus to the soil on the top layers of various types of slope. This study conducts a survey and an analysis of the characteristics of landslides that occurred in the study area with different geological conditions of granite and gneiss. The characteristics of soil in the area and its surroundings that have or have not undergone landslides for every geological condition is also evaluated. Based on these characteristics and a statistics method, it extracts the triggering factors, permeability coefficients (k), and shearing strength with cohesion (c) and internal friction angel (φ) of soils that are highly related to landslides around weathered soil layers. As a result, the permeability coefficients show significant relevance with void ratio (e), the effective size of grains (D10), and uniformity coefficient (cu), while the shearing strength with the proportion of fine-grained soil (Fines), uniformity coefficient (cu), degree of saturation (S), dry weight density (rd), and void ratio (e). By obtaining this result, the study uses the regression analysis to suggest models to estimate the permeability coefficients and shearing strength. For the gneiss area, the statistics-based estimation model (SEM) is proposed as k_gn = (1.488 × 10^-02 × e) + (1.076 × D₁₀) + (-1.629 × 10^-04 × c_u) - (1.893 × 10^-02) for permeability coefficients; cgn = (-0.712 × Fines) + (-0.131 × c_u) + 15.335 for cohesion; and φgn = (27.01 × r_d) + (-12.594 × e) + 6.018 for internal frictional angle of soils. For the granite area, the statistics-based estimation model (SEM) is proposed as kgr = (8.281 × 10^-03 × e) + (0.639 × D₁₀) + (-2.766 × 10^-05 × c_u) - (9.907 × 10^-03) for permeability coefficients; c_gr = (-0.689 × Fines) + (-0.0744 × S) + 18.59 for cohesion; and φ_gr = (33.640 × r_d) + (-0.875 × e) - 9.685 for internal frictional angle of soils. The use of statistics-based estimation models (SEMs) for landslide-triggering factors that trigger landslides will support the simple calculation of permeability coefficient and shearing strength (cohesion and internal frictional angle), only requiring information about the physical properties of soil at the natural slopes that have different geological features such as gneiss and granite areas.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

Studies report variable effects of sex hormones on serious diseases. Severe disease and mortality rates in COVID-19 show marked gender differences that may be related to sex hormones. Sex hormones regulate the expression of the viral receptors ACE2 and TMPRSS2, which affect the extent of viral infection and consequently cause variable outcomes. In addition, sex hormones have complex regulatory mechanisms that affect the immune response to viruses. These hormones also affect metabolism through obesity, and severe disease can result from complications such as thrombosis. This review presents the latest research on the regulatory functions of hormones in viral receptors, immune responses, complications as well as their role in COVID-19 progression. It also discusses the therapeutical possibilities of these hormones by reviewing the recent findings of clinical and assay studies.

Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). There is a lot of background noise in the vibration signal of diesel engine. To solve the problem, a denoising algorithm based on VMD and Euclidean Distance is proposed. Firstly, a multi-component, non-Gauss, and noisy simulation signal is established, and decomposed into a given number K of band-limited intrinsic mode functions by VMD. Then the Euclidean distance between the probability density function of each mode and that of the simulation signal are calculated. The signal is reconstructed using the relevant modes, which are selected on the basis of noticeable similarities between the probability density function of the simulation signal and that of each mode. Finally, the vibration signals of diesel engine connecting rod bearing faults are analyzed by the proposed method. The results show that compared with other denoising algorithms, the proposed method has better denoising effect, and the fault characteristics of vibration signals of diesel engine connecting rod bearings can be effectively enhanced.

Direct laryngoscope and videolaryngoscope are the dominant endotracheal intubation tools. Styletubation technique (using a video-assisted intubating stylet) has shown its advantages regarding in short intubation time, high success rate, less stimulation, and operator’s satisfaction. The learning curve can be steep but easy to overcome if the technical pitfalls could be avoided. Conditions make styletubation challenging include secretions/blood, short/stiff neck, restricted mouth opening and cervical spine mobility, anatomical abnormalities over head and neck regions, and obesity, etc. In this clinical report, we present the effectiveness and efficiency of routine use of the styletubation for tracheal intubation in a super-super obese patient (BMI 103 kg/m2) undergoing bariatric surgery with laparoscopic sleeve gastrectomy.

Calcium (Ca) is an essential element constituting sedimentary carbonate in subducting sediments. Ca isotopic characteristics of subduction-related rocks could provide insight into the behavior and budget of carbonate and carbon cycles in subduction zones, due to the distinctive δ^44/40Ca ranges of sedimentary carbonate with respect to the mantle. Here, we studied the Ca isotopic compositions of arc magmas from the Northern Luzon arc (NLA), which are evolved from a depleted mantle metasomatized by slab-derived fluids and sediment melts. The δ^44/40Ca values range from 0.76 ± 0.04‰ to 1.01 ± 0.03‰ and cover the typical ranges for bulk silica earth (BSE, ~ 0.94‰) and fresh mid-ocean ridge basalt (MORB, ~ 0.83‰). The Ca isotopes of NLA volcanics are not dominantly determined by the effects of mantle partial melting or fractional crystallization, nor significantly modified by secondary alteration. Instead, the δ^44/40Ca values of NLA volcanics are controlled by the subduction-related metasomatism. The metasomatism by slab-derived fluids (mainly expelled from altered oceanic crust, AOC) dramatically elevated the contents of fluid-mobile elements (e.g., Ba and Pb) with respect to fluid-immobile elements (e.g., Ce). This process, however, rarely modified the Ca isotopes, possibly ascribed to the δ^44/40Ca similarity between AOC and the depleted mantle. The δ^44/40Ca values significantly correlated with subduction indicators (e.g., Sr-Nd isotopes, Ba/Nb, Ce/Pb, and Nb/La), demonstrating the Ca isotopes of NLA volcanics are mainly controlled by the metasomatism of sediment melts subducting from the South China Sea (SCS). Based on the thermal structures and chemical compositions of sediments subducting into global trenches, we propose that carbonate Ca isotopic signals can only be observed in the arcs with high sedimentary Ca fluxes and temperature-pressure conditions well beyond the solidus of H₂O-saturated sediment melting, e.g., NLA, Nicaragua, Guatemala, Colombia, Peru, South Chile, North Vanuatu, New Zealand, and Kermadec. The absence of such signals in other arcs suggests either limited sedimentary fluxes or much of the subducting sedimentary carbonate has been survived during plate subduction to enter the deep mantle.

Alternative splicing can produce transcripts that affect cancer development and shows potential for cancer diagnosis and treatment. However, intron retention (IR), a type of alternative splicing, has been less systematically studied in cancer biology research. Here, we generated a pan-cancer IR landscape for more than 10,000 samples across 33 cancer types from The Cancer Genome Atlas (TCGA). We characterized differentially retained introns between tumor and normal samples and identified retained introns associated with survival. We discovered 988 differentially retained introns in 14 cancers, some of which demonstrated diagnostic potential in multiple cancer types. We also inferred a large number of prognosis-related introns in 33 cancer types, and the associated genes included well-known cancer hallmarks such as angiogenesis, metastasis, and DNA mutations. Notably, we discovered a novel intron retention event inside 5′UTR of STN1 that is associated with the survival of lung cancer patients. The retained intron reduces translation efficiency by producing upstream open reading frames (uORFs) and thereby inhibits colony formation and cell migration of lung cancer cells. Besides, the IR-based prognostic model achieved good stratification on certain cancers, as illustrated in acute myeloid leukemia. Taken together, we performed a comprehensive IR survey at a pan-cancer level, and the results implied that IR has the potential to be diagnostic and prognostic cancer biomarkers, as well as new drug targets.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V-microalloying 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure was consisted of ferrite, RA and secondary martensite (SM) after subjected to SPA process. (V, Mo)C with disc-like morphology mainly precipitated during intercritial tempering, and the aspect ratio of particle decreased, leading to the appearance of near-spherical morphology. After subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: out layer of ferrite, interlayer of SM and inner layer RA) enabled high yield strength of 1097 MPa, total elongation of 14%, and impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated about 108 MPa.

Dayaoshan, as an important metal ore producing area in China, is faced with the dilemma of resource depletion due to long-term exploitation. In this paper, remote sensing method is used to circle the favorable metallogenic areas and find new ore points for Gulong. Firstly, vegetation interference bas been removed by using mixed pixel decomposition method with hyperplane and genetic algorithm (GA) optimization; then, altered mineral distribution information has been extracted based on principal component analysis (PCA) and support vector machine (SVM) method; Thirdly, the favorable areas of gold mining in Gulong has been delineated by using ant colony algorithm (ACA) optimization SVM model to remove false altered minerals; Lastly, field survey verified that the extracted alteration mineralization information is correct and effective. The results show that the mineral alteration extraction method proposed in this paper has certain guiding significance for metallogenic prediction by remote sensing.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

Biomimetic foods are expected to have potential health benefits for the management and prevention of chronic diseases, such as diabetes and cardiovascular disease. In the current research, two commercially available and affordable plant proteins (soy protein isolate-SPI and pea protein isolate-PPI) at two levels (5%, 10%) were added to the Yangyu jiaotuan with an objective to develop a product with reduced glycemic properties and high protein content while maintaining its original taste and texture. The results showed that several important textural properties such as hardness and chewiness did not change significantly during the refrigerated storage. The storage modulus G′ increased with refrigerated storage time for different samples, there were significant differences among the five samples (with and without protein addition) with respect to frequency dependence during rheological measurements. The in vitro starch digestion experiments showed that the starch hydrolysis of Yangyu jiaotuan decreased considerably with the increase in PPI content and during refrigerated storage due to starch retrogradation. Protein has protected the microstructure and there was less damage when compared to samples without protein. The bimodal peaks of the particle size distribution curves showed that the newly developed Yangyu jiaotuan contains two different sizes of particles, the smaller particles (~30 μm) corresponded to PPI and starch granules, while the larger particles corresponded to the fragments of gel network of the starch matrix. Based on the above results, Yangyu jiaotuan mixed with pea protein is a convenient potato staple food product, which complies with the biomimetic potato food very well.

To study the mechanism of light color on a sea urchin (Tripneustes gratilla), blue light (B, λ450nm), yellow light (Y, λ585-590nm), red light (R, λ640nm), green light (G, λ510nm), white light (W, λ400-780nm) and darkness groups (H) were set up in a seawater recirculating aquaculture system. Six different LED light color treatment groups with a photoperiod of 12 L:12 D were tested for 30 d to investigate the effects of different light colors on the feeding, growth and enzyme activities of T. gratilla (142.45±4.36 g). We found that varying LED light colors significantly impacts the feeding, growth, and enzyme activity of T. gratilla. Notably, the sea urchins in group B exhibited better growth with a weight gain rate of 39.26%, while those in group R demonstrated poorer growth with a weight gain rate of only 26%. The feeding differed significantly (P&lt;0.01) between groups B and R, with group B consuming the highest daily intake (6.03±1.69 g) and group R consuming the lowest (4.54±1.26 g). Throughout the three phases, there was no significant change in the viability of the AMS (P&gt;0.05). Conversely, pepsin viability significantly increased (P&lt;0.01) in group B. LPS viability remained consistently at the lowest level, with no notable differences in group W from those observed in group B. In group R, both AMS and pepsin viability remained lower, whereas lipase viability was noticeably higher in each phase compared to group B (P&lt;0.01). Regarding antioxidant enzymes, group R exhibited a trend of initially increasing and then decreasing CAT, SOD, and GSH-PX activities, particularly during the third stage (15-30 d), with a significant decrease observed in antioxidant enzyme activities (P&lt;0.01). The outcomes suggest that blue light positively affects the growth, feeding, digestion, and antioxidant capacity of T. gratilla in comparison to other light environments, whereas the red light has an inhibitory impact.

The land subsidence occurring in goafs after coal mining is a protracted process. The accurate prediction of long-term land subsidence in goafs relies heavily on the availability of long-term monitoring data. However, the scarcity of continuous long-term land subsidence monitoring data subsequent to the cessation of mining significantly hinders the accurate prediction of long-term land subsidence in goafs. To address this challenge, this study proposes an innovative method based on Interferometric Synthetic Aperture Radar (InSAR) for predicting long-term land subsidence of goafs following coal mining. The proposed method employs a concatenation approach that integrates multiple short-term monitoring data from different coal faces, each with distinct cessation times, into a cohesive and uniform long-term sequence by normalizing the subsidence rates. The method was verified using actual monitoring data from the Yangquan No.2 mine in Shanxi Province, China. Initially, coal faces with same shapes but varying cessation times were selected for analysis. Using InSAR monitoring data collected between June and December of 2016, the average subsidence rate corresponding to the duration after coal mining cessation of each coal face was back-calculated. Subsequently, a function relating subsidence rate to the duration after coal mining cessation was fitted to the data. Finally, the relationship between cumulative subsidence and the duration after coal mining cessation was derived by integrating the function. The results indicated that the relationship between subsidence rate and duration after coal mining cessation followed an exponential function for a given coal face, whereas the relationship between cumulative subsidence and duration after coal mining cessation conformed to the Knothe time function. Notably, after the cessation of coal mining, significant land subsidence persisted in the goaf of the Yangquan No.2 mine for a duration ranging from 5 to 10 years. The cumulative subsidence curve along the long axis of the coal face ultimately exhibited an inclined W-shape. The proposed method enables the quantitative prediction of residual land subsidence in goafs, even in cases where continuous long-term monitoring data are insufficient, thus providing valuable guidance for construction decisions above the goaf.

Improper lifting measures of long-span spatial steel structures during construction process may delay the construction period and even cause safety accidents. Few studies on long-span spatial steel structures considered time-varying mechanical characteristic during construction process. In order to achieve safe and efficient installation in a long-span spatial steel structure, this research presents a time-varying mechanical analysis of the synchronous and asynchronous integral lifting and a single and interlaced point’s asynchronous integral lifting analysis method of a long-span spatial steel structure. The results showed that in the case of asynchronous lifting of single point, the displacement influence on other members is related to the distance. The closer the distance from the lifting point, the greater the influence. In asynchronous integral lifting, the lifting point with large lifting force is first installed to the specified position, and the lifting point with small lifting force is installed to the specified position.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Purinergic signaling is that nucleotides (especially ATP) and adenosine are utilized as transmitter molecules, which play an important role in the immune system. In the extracellular ventricle, ATP plays a significant role of pro-inflammatory molecules mainly through activating P2 receptors, while adenosine plays the role of anti-inflammatory molecules mainly through activating P1 receptors. As we know，neutrophils are the most abundant immune cells in our circulation and have become an essential part of coordinating a series of complex events during inflammatory diseases. However, due to the destruction of inflammatory substances from neutrophils, the activation of neutrophils is fine-tuned, and purinergic signaling is associated with this process. As a matter of fact, altering the balance between P2 and P1 signals is of great importance for neutrophils to exert immune activities properly. Here, we review the role of purinergic signaling in regulatory function of neutrophils during inflammatory disease, and then discuss the potential contribution of targeted purinergic signals in the treatment of the neutrophil during inflammatory diseases.

Surgical smoke is produced by energy-based surgical instruments. The airborne volatile organic compounds (VOCs) from surgical smoke may have potential health risk. This study aimed to evaluate the evidence for the harmful effects on the operating theater staff. An internationally recognized evaluation model of health risk assessment (HRA) was adapted to preliminarily assess the health risks caused by VOCs in surgical smoke. Results of HRA indicated that non-carcinogenic risk indexes of VOCs did not exceed one, indicating that these pollutants didn't cause significant non-carcinogenic harm to the health of the operating theater staff. But the cancer risk indexes exposed to formaldehyde and benzene all exceed 10-5, which was higher than the suggested value of USEPA (10-6) and might cause potential harm to the health of the operating theater staff. Long-term exposure of such surgical smoke will be harmful to the health of the operating theater staff and have a great risk of cancer.