Global navigation satellite system (GNSS) array antenna receivers are widely used to suppress wideband interference in navigation countermeasures. However, existing array antenna receivers all adopt digital array structure and digital beamforming technique, and it has limited analog-front-end (AFE) dynamic range. In strong interference scenarios, AFE saturation will occur, which limits the maximum interference suppression ability of the array receiver. Aiming at this issue, this paper proposes a robust wideband interference suppression method for GNSS array antenna receivers based on hybrid beamforming technique. Firstly, a novel fully connected hybrid array receiver structure is proposed; Secondly, the corresponding hybrid beamforming method is proposed at the same time, and it realizes the complete elimination of strong interference by jointly suppression in analog domain and digital domain. After mathematical simulation experiments, it is verified that compared to the digital beamforming-based anti-jamming technique, the proposed method can effectively suppress strong wideband interference, and the maximum interference suppression ability is improved by 36 dB.

An innovative wireless sensor network (WSN) based on Ultra-Wide Band (UWB) technology for 3D accurate superficial monitoring of ground deformations, as landslides and subsidence, is proposed. The system has been designed and developed as part of an European Life+ project, called Wi-GIM (Wireless Sensor Network for Ground Instability Monitoring). The details of the architecture, the localization via wireless technology and data processing protocols are described. The flexibility and accuracy achieved by the UWB two-way ranging technique is analysed and compared with the traditional systems, such as robotic total stations (RTSs), Ground-based Interferometric Synthetic Aperture Radar (GB-InSAR), highlighting the pros and cons of the UWB solution to detect the surface movements. An extensive field trial campaign allows the validation of the system and the analysis of its sensitivity to different factors (e.g., sensor nodes inter-visibility, effects of the temperature, etc.). The Wi-GIM system represents a promising solution for landslide monitoring and it can be adopted in conjunction with traditional systems or as an alternative in areas where the available resources are inadequate. The versatility, easy/fast deployment and cost-effectiveness, together with the good accuracy, make the Wi-GIM system a possible solution for municipalities that cannot afford expensive/complex systems to monitor potential landslides in their territory.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

This paper investigates the effect of the Internet on tax revenue instability, notably through the international trade channel. It has used a sample of 142 countries over the period 1995-2017, and relied primarily on the two-step system Generalized Methods of Moments (GMM) estimators (but also incidentally on the Error Component Two-Stage Least Squares estimator). Tax revenue instability is primarily measured by the instability of non-resource tax revenue, but also by the instability of total tax revenue (for robustness check). The findings indicate that the Internet exerts a negative effect on tax revenue instability. Interestingly, this effect genuinely translates through the international trade channel, regardless of the measure of tax revenue instability considered. Countries enjoy a higher negative effect of the Internet on tax revenue instability as they enjoy a greater participation in international trade. These findings, therefore, add to the potential benefits of the Internet adoption (e.g., strengthening countries' participation in international trade, enhance their tax revenue performance and promote tax reform, including in developing countries) by showing that it could also help to stabilize tax revenue, particularly through the degree of countries' participation in international trade.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

An entropic origin of gravity is re-visited. Isothermal self-gravitating cloud seen as an ideal gas is analyzed. Gravitational attraction within the isothermal cloud in equilibrium is balanced by the pressure, which is of a pure entropic nature. The notion of the Jeans entropy of the cloud corresponding to the entropy of the self-gravitating cloud in mechanical and thermal equilibrium is introduced. Balance of the gravitational compression and the entropic repulsion yields the scaling relation hinting to the entropic origin of the gravitational force. The analysis of the Jeans instability enables elimination of the “holographic screen” or “holographic principle” necessary for grounding of the entropic origin of gravity.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

Understanding the subtle signs of carpal instability and other unique injury patterns in the wrist is a critical skill for radiologists. Proper patient management and outcomes are directly dependent on the accurate interpretation of wrist imaging studies. This review will provide a detailed overview of typical imaging features of carpal trauma and instability, management, and complications, using multimodality imaging and original medical illustrations. A detailed overview of the osseous, ligamentous, arterial anatomy of the wrist, arcs of Gilula, and zones of vulnerability will be provided. Carpal fractures, dislocations, special radiographic views, and imaging pearls will be discussed. Instability patterns and the myriad of associate abbreviations (CID, CIND, CIC, CIA, VISI, DISI, SLD, LTD, MCI, SLAC, SNAC) will be clarified. Expected outcomes, potential complications, and management will be reviewed.

Chemical instability of liquid-repellent surfaces is one of the nontrivial hurdles that hinders their real-world applications. Although much efforts have been made to prepare chemically durable liquid-repellent surfaces, few attentions have been paid to exploit the instability for versatile use. Herein, we propose to create hydrophilic patterns on superhydrophobic surface by taking advantage of its chemical instability induced by acid solution treatment. Superhydrophobic Cu(OH)2 nanoneedles covered Cu plate that shows poor stability towards HCl solution (1.0 M) is taken as an example. Results show that 2.5 min of HCl solution exposure leads to the etching of Cu(OH)2 nanoneedles and partial removal of self-assembled fluoroalkyl silane molecular layer, resulting in the wettability transition from superhydrophobocity to hydrophilicity, and the water contact angle decreases from ~160° to ~30°. Hydrophilic dimples with different diameters are then created on the superhydrophobic surfaces by depositing HCl droplets with different volumes. Afterwards, the hydrophilic dimple patterned superhydrophobic surfaces are used for water droplet manipulations, including controlled transfer, merging and nanoliter droplets deposition. The results thereby verify the feasibility of creating wettability patterns on superhydrophobic surfaces by using their chemical instability towards corrosive solutions, which broadens the fabrication methods and applications of functional liquid-repellent surfaces.

Elbow dislocation and instability present significant clinical challenges, necessitating a thorough understanding of the underlying bio-mechanical mechanisms. In this study, a quasi-static three-dimensional finite element model of the human elbow joint is developed to investigate stress distribution and stages of dislocation in the human elbow under various loading conditions. The model simulates the elbow joint in different degrees of flexion (30°, 45°, 60°, and 90°) and forearm positions (pronation and supination), providing detailed insights into the progression of dislocation. Significant findings include the identification of high stress concentrations on the humerus at 90° flexion and on the radial and coronoid processes at 30°, 45°, and 60° flexion. Three reproducible stages of dislocation were observed, particularly in flexed positions with forearm pronation or supination. These stages align with experimental observations and highlight the initial occurrence of bony failures, such as radial head and ulnar coronoid fractures, preceding soft tissue tears. Clinically, the study underscores that early-stage low-impact posterior elbow dislocations retain enough stability to be managed with closed reduction and early mobilization. However, as dislocations progress, significant damage to the medial and lateral collateral ligaments is expected, necessitating more invasive treatments. This research provides valuable bio-mechanical insights into elbow dislocation, aiding in the development of improved treatment strategies and enhancing patient outcomes through precise and timely clinical interventions. The validated FEM serves as a powerful tool for pre-surgical planning offering a comprehensive understanding of elbow joint mechanics.

The management of shoulder instability in children and adolescents is a challenging field of orthopaedics. There are several complicating factors which originate from the variable underlying cause that is often a unique combination of traumatic factors, ligamentous laxity, and the pattern of muscle contractility. As the cause is often multifactorial, this makes interpretation of the literature difficult as nomenclature is variable. The purpose of this review is to shed light on the nuances of paediatric and adolescent shoulder instability.

Chromosomal instability (CIN), defined by variations in the number or structure of chromosomes from cell to cell, is recognized as a distinctive characteristic of cancer, associated with the ability of tumors to adapt to challenging environments. CIN has been recognized as a source of genetic variation that leads to clonal heterogeneity (CH). Recent findings suggest a potential association between CIN and CH with the prognosis of BC patients, particularly in tumors expressing the epidermal growth factor receptor 2 (HER2+). In fact, information on the role of CIN in other BC subtypes, including luminal B BC, is limited. Additionally, it remains unknown whether CIN in luminal B BC tumors, above a specific threshold, could have a detrimental effect on the growth of human tumors, or if low or intermediate CIN levels could be linked to a more favorable BC patient prognosis when contrasted with elevated levels. Clarifying these relationships could have a substantial impact on risk stratification and the development of future therapeutic strategies aimed at targeting CIN in BC. This study aimed to assess CIN and CH in tumor tissue samples from ten patients with luminal B BC, and compared them with established clinicopathological parameters. The results of our study show that luminal B BC patients exhibit intermediate CIN and stable aneuploidy, both of which correlated with lymphovascular invasion. These findings suggest that evaluating CIN, CH and aneuploidy could improve risk stratification, the prediction of clinical outcomes and future therapeutic approaches in luminal B BC patients.

The integrity of the genome is crucial for the survival of all living organisms. However, genomes need to adapt to survive certain pressures and for this propose use several mechanisms to diversify. Chromosomal instability (CIN) is one of the main mechanism leading to the creation of genomic heterogeneity by altering the number of chromosomes as well as changing their structures. In this review we will discuss the different chromosomal patterns and changes observed in speciation, in evolutional biology as well as during tumor progression. By nature, human genome shows induction of diversity during gametogenesis but as well during tumorigenesis that can conclude in drastic changes such as whole genome doubling to more discrete changes as indels as well as the recent discovered complex chromosomal rearrangement chromothripsis. More importantly, changes observed during speciation are strikingly similar to the genomic evolution observed during tumor progression and resistance to therapy. The different origins of CIN will be treated as the importance of double strand breaks (DSB) or the consequences of micronuclei. We will also explain the mechanisms behind the controlled DSBs and recombination of homologous chromosomes observed during meiosis, to explain how errors lead to similar pattern observed during tumorigenesis. Then, we will also list several diseases associated to CIN resulting in fertility issue, miscarriage, genetic rare diseases and cancer. Understanding better chromosomal instability as a whole is primordial for the understanding of mechanisms leading to tumor progression.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

Abstract: We present a technological analysis of the architectonic complex associated with a firing structure (locally named fogón) on top of the Pirámide Mayor, the largest pyramid in Caral. This Archaic Period society flourished between ca 2,700 and 2,000 cal B.C. and was located near the Pacific Ocean on the north-central coast of present-day Peru. All approaches employed in this study demonstrated that the corridor with antechamber and duct on top of Pirámide Mayor of Caral was a sophisticated ventilation system capable of providing between 3,000 and 18,000 liters of air per minute for combustion in the attached fogón. The analysis indicates that ventilating the fogón must have been a major consideration in deciding a) the construction of the pyramid, b) locating the structure at the edge of a natural alluvial terrace, and c) orientating the pyramid towards the then contemporary prevailing winds. Results from the analysis of this fogón support practical decisions made by the builders and challenge the assumption that religion or politics were the only considerations in American pyramid building. It also indicates that a complex device, capable to delivering the considerable airflows reported in this study was within the reach of an archaic society in ancient Peru. The application of this structure to the production of a remarkably high thermal output and its implications on the knowledge of ancient Americans will be discussed in a following companion article.

Keywords: Amorphous-precipitate, Nitride, Morphological stability, Diffusion, Internal stresses, Modelling, Simulation

In this study, we deal with a nonlinear system of neutral Volterra integro-differential equations (NVIDEs) with infinite delay. We study stability, uniform stability and instability of zero solution of the system of NVIDEs with infinite delay. We obtain three new results with regard to these concepts via two new Lyapunov– Krasovskii functionals (LKFs), respectively. As the main contributions of this work, we improve and generalize some earlier results in the relevant database from the linear case to more general nonlinear cases.

Genetic activation of the class I PI3K pathway is very common in cancer. This mostly results from oncogenic mutations in PIK3CA, the gene encoding the ubiquitously expressed PI3Kα catalytic subunit, or from inactivation of the PTEN tumour suppressor, a lipid phosphatase which opposes class I PI3K signalling. The clinical impact of PI3K inhibitors in solid tumours, aimed at dampening cancer-cell-intrinsic PI3K activity, has thus far been limited. Challenges include poor drug tolerance, incomplete pathway inhibition and pre-existing or inhibitor-induced resistance. The principle of pharmacologically targeting cancer-cell-intrinsic PI3K activity also assumes that all cancer-promoting effects of PI3K activation are reversible, which might not be the case. Emerging evidence suggests that genetic PI3K pathway activation can induce and/or allow cells to tolerate chromosomal instability, which – even if occurring in a low fraction of the cell population – might help to facilitate and/or drive tumour evolution. While it is clear that such genomic events cannot be reverted pharmacologically, a role for PI3K in the regulation of chromosomal instability could be exploited by using PI3K pathway inhibitors to prevent those genomic events from happening and/or reduce the pace at which they are occurring, thereby dampening cancer development or progression. Such an impact might be most effective in tumours with clonal PI3K activation and achievable at lower drug doses than the maximum-tolerated doses of PI3K inhibitors currently used in the clinic.

The patellofemoral joint (PFJ) is a complex articulation between the patella and the femur, in-volved in the extensor mechanism of the knee. Patellofemoral disorders can be classified into ob-jective patellar instability, potential patellar instability, and patellofemoral pain syndrome. An-atomical factors such as trochlear dysplasia, patella alta, and tibial tuberosity-trochlear groove (TT-TG) distance contribute to instability. Patellofemoral instability can result in various types of dislocations, and the frequency of dislocation can be categorized as recurrent, habitual, or per-manent. Primary patellar dislocation requires diagnostic framing, including physical examina-tion and imaging. Magnetic resonance imaging (MRI) is essential for assessing the extent of damage, such as bone bruises, osteochondral fractures, and medial patellofemoral ligament (MPFL) rupture. Treatment options for primary dislocation include urgent surgery for oste-ochondral fragments or conservative treatment for cases without lesions. Follow-up after treat-ment involves imaging screening and assessing principal and secondary factors of instability. Detecting and addressing these factors is crucial for preventing recurrent dislocations and opti-mizing patient outcomes.

Abstract: Fanconi anemia (FA), a chromosomal instability syndrome, is caused by inherited pathogenic variants in any of 22 FANC genes, that cooperate in the FA/BRCA pathway. This pathway regulates the repair of DNA interstrand crosslinks (ICLs) through homologous recombination. In FA proper repair of ICLs is impaired, and accumulation of toxic DNA double strand breaks occurs. In order to repair this type of DNA damage, FA cells activate alternative error-prone DNA repair pathways, that may lead to the formation of gross structural chromosome aberrations of which radial figures are the hallmark of FA and their segregation during cell division are the origin of subsequent aberrations like translocations, dicentrics and acentric fragments. The deficiency in DNA repair has pleiotropic consequences in the phenotype of patients with FA, including developmental alterations, bone marrow failure and an extreme risk to develop cancer. The mechanisms leading to the physical abnormalities during embryonic development have not been clearly elucidated, however FA has features of premature aging with chronic inflammation mediated by pro-inflammatory cytokines, that results in tissue attrition, selection of malignant clones and cancer onset. Moreover, the effect of the FA/BRCA pathway in germinal cells, evidenced by infertility in patients with FA attests of chromosomal instability and cell death also occurring in the germinal compartment.

The feasibility of using full ion kinetics, instead of gyrokinetics, in simulating low-frequency Ion-Temperature-Gradient (ITG) instabilities in tokamaks has recently been demonstrated by Sturdevant et al. [Physics of Plasmas 24, 081207 (2017)]. In that work, a variational integrator was developed to integrate the full orbits of ions in toroidal geometry, which proved to be accurate in capturing both the short-time scale cyclotron motion and long time scale drift motion. The present work extends that work in three aspects. First, we implement a relatively simple full orbit integrator, the Boris integrator, and demonstrate that the accuracy of this integrator is also sufficient for simulation of ITG instabilities. Second, the equilibrium magnetic configuration is extended to general toroidal configuration specified numerically, enabling simulation of realistic equilibria reconstructed from tokamak experiments. Third, we extend that work to the nonlinear regime and investigate the nonlinear saturation of ITG instabilities. To verify the new numerical implementation of the orbit integrator and magnetic configuration, the linear electrostatic ITG frequency and growth rate are compared with those given in Sturdevant's work and good agreement is found.

Balance requires constant adjustments in muscle activation to attain force steadiness. Creating appropriate training can be challenging. The purpose of this study was to examine the effects of two weeks front squat instability training using a water-filled training tube on force steadiness during an instability challenge. Control (CON, n= 13) and experimental (EXP, n=17) subjects completed pre and post testing for EMG variability by completing one set of 10 repetitions with a stable and unstable training tube. Electrodes were placed bilaterally on the anterior deltoid, paraspinal and vastus lateralis muscles. CON subjects completed 2 weeks of training using a stable training tube, while EXP subjects trained with a water-filled instability tube. EMG data were integrated for each contraction and force steadiness computed using the natural log of coefficient of variation. CON results showed no changes in force steadiness for any condition. EXP showed significant reductions in EMG activation variability across all muscles. These results indicate a significant training effect in reducing muscle activation variability in subjects training with a water-filled instability training device. Improvements seen in these healthy subjects supports development of training implements for a more clinical population to help improve force steadiness.

Papillary thyroid carcinoma (PTC) has two main histologic variants: classical-PTC (CL-PTC) and follicular variant PTC (FV-PTC). Recently, due to its similar features to benign lesions, the encapsulated FV-PTC variant was reclassified as noninvasive follicular thyroid neoplasm with papillary-like nuclear features (NIFTP). Nonetheless, specific molecular signatures are not yet available. It is well known that telomere-related genome instability is caused by inappropriate DNA repair of dysfunctional telomeres and that mechanisms involved in the damaged telomere repair processing may led to detrimental outcomes, altering the 3D nuclear telomere and genome organization in cancer cells. This pilot study aimed to evaluate whether a specific nuclear telomere architecture might characterize NIFTP, potentially distinguishing it from other PTC histologic variants. Our findings demonstrate that 3D telomere profiles of CL-PTC and FV-PTC were different from NIFTP and that NIFTP more closely resembles follicular thyroid adenoma (FTA). NIFTP has longer telomeres than CL-PTC and FV-PTC samples and telomere length overlaps in NIFTP and FTA. There was no association between BRAF expression and telomere length in all tested samples. Our data showing that 3D nuclear telomere organization is altered differently in thyroid cancer variants, suggest that this parameter might guide clinical management of NIFTP. Although further investigations in a larger cohort of patients are necessary to corroborate our observations, telomere-related genomic instability might be of value in the diagnosis of NIFTP and allow for a more appropriate selection of the correct treatment.

The purpose of this paper is to simulate a two-dimensional Rayleigh-Taylor instability problem using the classical method of Finite Element analysis of a multiphase model using ANSYS FLUENT 19.2. The governing equations consist of a system of coupled nonlinear partial differential equations for conservation of mass, momentum and phase transport equations. The study focuses on the transient state simulation of Rayleigh Taylor waves and subsequent turbulent mixing in the two phases incorporated in the model. The Rayleigh Taylor instability is an instability of an interface between two fluids of different densities which occurs when the lighter fluid is pushing the heavier fluid in a gravitational field. The problem was governed by the Navier-Stokes and Cahn-Hilliard equations in a primitive variable formulation. The Cahn- Hilliard equations were used to capture the interface between two fluids systems. The objective of this article is to perform grid dependency test on Rayleigh Taylor Instability for 2 different mesh size and compare the results for the variation in Atwood Number. The results were validated with the observations from previous published literatures.

Emergence of zoonotic-human pathogens is proven to be a lethal threat to public health, and RNA virus including influenza viruses, severe acute respiratory syndrome coronavirus, middle east respiratory syndrome coronavirus, Wuhan coronavirus (COVID-19), plays a pivotal role. As those viruses as airborne microorganisms spread mainly by tiny airborne particles, it is important to de-active those airborne particles before their entry into human bodies. In this study, we investigated the effect of far infrared (FIR) radiation on inhibition of airborne microorganisms. The result confirmed that double stand DNA from airborne microorganisms were stable under mild FIR radiation. However, single strand RNA from them was found to be sensitive to FIR radiation, indicating that RNA virus in airborne particles is instable under FIR radiation. Based on this observation, two models on usage of FIR radiation to prevent RNA virus transmission and cure RNA virus infection were proposed, implying that FIR radiation might be a cheap, convenient, and efficient method in clinic to treat RNA virus.

Behavioral instability is a new concept used for indicating environmental stress based on behavioral traits. This study investigates the possibility of using behavioral instability as a tool for assessing personality in captive animals. The understanding of personality in captive animals can be a resourceful tool in the development of enrichment programs in order to improve animal welfare. In this study it is examined how an olfactory stimulus affects the behavior of two individuals of the species Ursus maritimus in captivity. When using continuous focal sampling throughout the day it was for many behaviors found that the individuals responded differently to stimuli, indicating that there was a difference in personality. This is shown using multiple approaches. One approach used traditional methods for behavioral analyses and the other approach used the concept of behavioral instability as a new quantitative method. This study proves use of behavioral instability as a new quantitative method for investigating personality, expanding the possibility of comparing personality between species. Moreover, it is shown that outliers, which cause asymmetric distributions, should not be removed in behavioral analysis without careful consideration.

Mechanisms for somatic chromosomal mosaicism (SCM) and chromosomal instability (CIN) are incompletely understood. During SNP-array molecular karyotyping and bioinformatic analyses of children with neurodevelopmental disorders and congenital malformations (n=612), we observed colocalizaion of regular chromosomal imbalances or copy number variations (CNV) with mosaic ones (n=47 or 7.7%). Analyzing molecular karyotyping data and pathways affected by CNV burdens, we proposed a mechanism for SCM/CIN, which had been designated as “chromohelkosis” (from the Greek chromosome ulceration/open wound). Briefly, structural chromosomal imbalances are likely to cause local instability (“wreckage”) at the breakpoints, which results either to partial/whole chromosome loss (e.g. aneuploidy) or elongation of duplicated regions. Accordingly, a function for classical/alpha satellite DNA (protection from the wreckage towards the centromere) has been hypothesized. Since SCM and CIN are ubiquitously involved in development, homeostasis and disease (e.g. prenatal development, cancer, brain diseases, aging), we have metaphorically (ironically) designate the system explaining chromohelkosis contribution to SCM/CIN as the cytogenomic “theory of everything” like the homonymous theory in physics inasmuch as it might explain numerous phenomena in chromosome biology. Recognizing possible empirical and theoretical weaknesses of this “theory”, we nevertheless believe that studies of chromohelkosis-like processes are required to understand structural variability and flexibility of the genome.

Over the past few decades, aircraft Ground Handling Operations (GHO) have been investigated by numerous researchers. Some aspects of GHO have been more focused on than others due to their importance in the GH processes. For instance, GHO performance has been tackled from different perspectives while workers and vehicles allocation suffer from the lack of research in the area. This paper is a literary review of the research that has been conducted in different areas of GHO. It sheds light on GHO performance, resource allocation and scheduling, operations scheduling, vehicle routing, and workers and vehicles allocation.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

Classifications of AAFD/PCFD have evolved with an increased understanding of the pathology involved. A review of classification systems helps identify deficiencies and respective contributions to the evolution in understanding the classification of AAFD. Using multiple electronic database searches (Medline, PubMed) and Google search, original papers classifying AAFD were identified. Nine original articles were identified that met the inclusion criteria. Johnson's original classification and multiple variants provided a significant leap in understanding and communicating the pathology but remained tibialis posterior tendon focussed. Drawbacks of these classifications include the implication of causality, linearity of progression through stages, an over-simplification of stage 2 deformity and a failure to understand multiple tendons react, not just tibialis posterior. Later classifications, such as the PCFD classification, are deformity-centric. Early instability in non-cavus feet and all stages of cavus feet can present pain and instability with minor/no deformity. These may not be captured in deformity-based classifications biased to planus feet.' The authors developed the 'Triple Classification' (TC) understanding that primary pathology is a progressive ligament failure/instability that presents as tendon reactivity, deformity, and painful impingement. There is a variable manifestation dependent on starting foot morphology. This review has identified deficiencies within classification systems used in AAFD/PCFD and, as a result, was used to help develop a more comprehensive 'Triple classification'. Advantages of the TC include representing foot types with no deformity, defining complex secondary instabilities, delinking of foot types, tendon reactivity/ligament instability and deformity to represent these independently in a more comprehensive classification system.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

Over the last few years, Earth Observation (EO) data has shifted towards increased use to produce official statistics, particularly in the agriculture sector. National statistics offices worldwide, including in Asia and the Pacific, are expanding their use of EO data to produce agricultural statistics such as crop classification, yield estimation, irrigation mapping, and crop loss estimation. The advances in image classification, such as pixel-based and phenology-based classifications, and machine learning create new opportunities for researchers to analyze EO data applied to agriculture statistics. However, it requires the ground truth (GT) data because classification result mainly depends on the quality of GT. Therefore, in this study, we introduced a random sampling approach to design and collect GT data using EO imagery and ancillary data. As a result of data collection, GT data improve the algorithms and validates classification results. Nevertheless, despite the importance of GT data, they are rarely disseminated as a data product in themselves. Thus, this results in an untapped opportunity to share GT data as a global public good, and improved use of survey and census data as a source of GT data.

It is unclear whether military shoes (combat boots and sports shoes) attenuate loading rate or affect force transfer during walking. Therefore, this study compared ground reaction forces (GRF) related to impact and force transfer between combat boots, military sports shoes and running shoes. Ten army recruits walked over a walkway with two force plates embedded. GRF were measured when walking barefoot (for data normalization) and with combat boots, military sports shoes and running shoes. Loading rate, first and second peak forces and push-off rate of force were computed along with temporal analysis of waveforms. Reduced loading rate was observed for the running shoe compared to the combat boot (p = 0.02 and d = 0.98) and to the military sports shoe (p = 0.04 and d = 0.92). The running shoe elicited a smaller second peak force than the combat boot (p < 0.01 and d = 0.83). Walking with military shoes and combat boots led to larger force transfer then running shoes potentially due to harder material used in midsole composition (i.e. styrene-butadiene rubber). These results could lead to a potentially larger risk of injuries while long duration walking in military shoes and boots compared to traditional running shoes.

Ballasted railway tracks can be modelled using reduced/simplified models composed of several layers of discrete components. This paper deals with the two-layer model, which is very popular due to its computational efficiency. In order to provide some recommendations for track design, it is necessary to identify which set of parameters leads to some irregular/unexpected behavior. Such irregularity is investigated at three levels, such as: (i) critical velocity of moving constant force; (ii) instability of a single moving mass; (iii) instability of two moving masses. All results are presented in dimensionless form to cover a wide range of real parameters. Irregular cases are identified by sets of parameters leading to them and then general conclusions are drawn. Regarding the method, all results are obtained analytically or semianalytically, where “semi” refers to solving the roots of a given polynomial by predefined numerical procedures in symbolic software. No numerical integration is involved in all results presented. This means that the results are highly accurate and refer to exact values, so any kind of parametric or sensitivity analyses is readily possible.

Interaction of an electromagnetic field with matter in a laser cavity without the assumption of a fixed direction of the transverse electric field, described by the two-level Maxwell-Bloch equations, is studied. By using a perturbative nonlinear analysis, performed near the laser threshold, we report on the derivation of the laser (3+1)D vectorial complex cubic-quintic complex Ginzburg-Landau equation. Furthermore, we study the modulational instability of the plane waves both theoretically using the linear stability analysis, and numerically, using direct simulations via the split-step Fourier method. The linear theory predicts instability for any amplitude of the primary waves. Our numerical simulations confirm the theoretical predictions of the linear theory as well as the threshold of the amplitude of perturbations. The system understudy shows a deep dependence on the laser cavity parameters, for which there appear wave patterns in accordance with the predictions from the gain spectrum.

In this paper, an analytical investigation of the combined effect of through flow and magnetic field on the convective instability in an electrically conducting fluid layer, bounded in a Hele-Shaw cell is presented within the context of linear stability theory. The Galarkin method is utilized to solve the eigenvalue problem. The outcome of the important parameters on the stability of the system is examined analytically as well as graphically. It is observed that the through flow and magnetic field have both stabilizing effects, while the Hele-Shaw number has destabilizing effect on the stability of system. It is also found that the oscillatory mode of convection possible only when the magnetic Prandtl number takes the values less than unity.

The issue of monitoring and early warning of rock instability has received increasing critical attention in the study of rock engineering. To investigate the damage evolution process of granite under triaxial compression tests, acoustic emission (AE) tests were performed simultaneously. This study firstly introduced two novel parameters, i.e., the coefficient of variation (CoV) of the information entropy and correlation dimension of the amplitude data from the AE tests, to identify the precursor of the failure of granite. Then the relationship between the changes in these parameters and the stress-time curve was compared and analyzed. The results of this study show that: (1) There is a strong correlation between the CoV of the information entropy and the failure process of granite. The granite failed when the CoV curve raised to a plateau. (2) The fluctuation of the correlation dimension indicates the different stages of the loading process, i.e., the initial compaction stage, the linear elastic stage, the yield stage, and the failure stage. Each stage contains a descending and a rising process in the correlation dimension curve, which indicates that this parameter could be used to identify the precursor of the failure as well. (3) The combined analysis of the two can improve the accuracy of rock instability prediction. This study provides new insights into the prediction of rock instability, which has theoretical implications for the stability of subsurface engineering rock masses.

The modulation instability of surface capillary-gravity water waves is analysed in a shear flow model with a tangential discontinuity of velocity. It is assumed that air blows along the surface of the water with a uniform profile in the vertical direction. Such a model, despite its simplicity, plays an important role in hydrodynamics as the reference model for investigating basic physical phenomena of wave-current interactions and acquiring insights into a series of complex phenomena. In certain cases where the wavelength of interfacial perturbations is much bigger than the width of the shear fow profile, the model with the tangential discontinuity in the velocity is adequate for describing physical phenomena at least within limited spatial and temporal frameworks. A detailed analysis of the air-flow conditions under which modulation instability sets in is presented. It is also shown that the interfacial waves are subject to dissipative or radiative instability when negativeenergy waves appear at the interface.

Soil transverse isotropy results in different stiffness characteristics in the horizontal and vertical directions. However, the effect is usually neglected in the seismic motion analysis. In this study, an equivalent linear anisotropic soil model was established based on the finite element method and investigated the impact of anisotropic parameters on ground motion at the site under various seismic wave inputs. It is found that the anisotropic parameters have a more significant effect for the seismic waves with the dominant frequency closer to the fundamental frequency of the site. As an example, the soil dynamic parameters in Shanghai Yangshan Port were calibrated by a series of bending elements, resonance columns, and cyclic triaxial tests. The influences of anisotropy on the peak ground acceleration (PGA) and response spectrum are studied for Yangshan Port. Addi-tionally, the standard design response spectra considering the soil anisotropy were provided. A comparison reveals that the existing isotropic design response spectrum may lead to dangerous seismic design for the structures at Yangshan port.

The many-body problem in quantum physics originates from the difficulty of describing the non-trivial correlations encoded in the exponential complexity of the many-body wave function. Motivated by the Giuseppe Carleo's work titled solving the quantum many-body problem with artificial neural networks [Science, 2017, 355: 602], we focus on finding the NNQS approximation of the unknown ground state of a given Hamiltonian $H$ in terms of the best relative error and explore the influences of sum, tensor product, local unitary of Hamiltonians on the best relative error. Besides, we illustrate our method with some examples.

First, a recently developed eigenfunction expansion technique, based in part on separation of the thickness-variable and partly utilizing a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism, is employed to derive three-dimensional singular stress fields in the vicinity of the front of an interfacial crack weakening an infinite bicrystalline superlattice plate, made of orthorhombic (cubic, hexagonal and tetragonal serving as special cases) phases, of finite thickness and subjected to the far-field extension/bending, in-plane shear/twisting and anti-plane shear loadings, distributed through the thickness. Crack-face boundary and interface contact conditions as well as those that are prescribed on the top and bottom surfaces of the bicrystalline superlattice plate are exactly satisfied. It also extends a recently developed concept of lattice crack deflection (LCD) barrier to a superlattice, christened superlattice crack deflection (SCD) energy barrier for studying interfacial crack path instability, which can explain crack deflection from a difficult interface to an easier neighboring cleavage system. Additionally, the relationships of the nature (easy/easy, easy/difficult or difficult/difficult) interfacial cleavage systems based on the present solutions with the structural chemistry aspects of the component phases (such as orthorhombic, tetragonal, hexagonal as well as FCC (face centered cubic) transition metals and perovskites) of the superlattice are also investigated. Finally, results pertaining to the through-thickness variations of mode I/II/III stress intensity factors and energy release rates for symmetric hyperbolic sine distributed load and their skew-symmetric counterparts that also satisfy the boundary conditions on the top and bottom surfaces of the bicrystalline superlattice plate under investigation, also form an important part of the present investigation.

Sediment cores were collected from a mudflow lobe (80 m water depth) offshore of the Mississippi River’s Southwest Pass in 2017 to better understand the sedimentology near the lobe entraining the SS Virginia shipwreck (sunk by a German U-Boat in 1942) and surrounding Mississippi River Delta Front. Core analyses included 210Pb/137Cs geochronology, granulometry, and X-radiography. Sediment accumulation rates (SAR) calculated from excess 210Pb activity in multicores are 0.22–0.29 cm/yr at seabed depths less than 20 cm and 0.29–0.51 cm/year at depths greater than 20 cm. 137Cs accumulation rates are ~0.15 to ~ 0.37 cm/year since 1954 and 1963 respectively. Sediment accumulation rates from 210Pb and 137Cs geochronology and indicators of relative sedimentation and bioturbation from X-radiographs suggest that rates of sediment accumulation near Virginia have declined since ca. the mid-20th century. This may be explained by the multi-decade downslope mass transport of the mudflow lobe in which the shipwreck is embedded, and decreases in sediment supply delivered offshore from the Mississippi River. Mass-transport calculations of the Virginia lobe derived from core properties and published lobe advection rates suggest downslope mass transport is far higher than sediment resupply from the Mississippi River, consistent with recent studies of delta retreat.

The goal of this study was to analyze the instability during stepping of young and older adults at fast and spontaneous speed. To this aim, the anteroposterior and the mediolateral distances between the body center of mass (COM) and the minimum moment axis (MMA) were computed. A total of 15 young adults (25y.o. [19-29]) and 15 older adults 68.7y.o. [63-77] volunteered for this study. For the computation of the distances, a complete biomechanical protocol combining two force platforms and a 3D motion capture analysis system was setup. The subjects were equipped with 47 reflective markers and were modeled as a frictionless multibody with 19 segments, 18 joints and 42 degrees of freedom and were asked to perform a stepping at both speeds. The stepping was divided in 5 phases with successive swing and double stance phases. The greater instability was observed during the swing phases. The distances indicate a significant higher instability at fast speed for both groups (p &lt; 0.001) for all the phases. The anteroposterior distance also increases significantly for older adults highlighting greater instability while no differences were observed for the mediolateral distance all along the 5 phases suggesting higher risks of backward of forward falls during stepping.

The onset of the thermal instability is investigated in a porous channel with plane parallel boundaries saturated by a non–Newtonian shear–thinning fluid and subject to a horizontal throughflow. The Ellis model is adopted to describe the fluid rheology. Both horizontal boundaries are assumed to be impermeable. A uniform heat flux is supplied through the lower boundary, while the upper boundary is kept at a uniform temperature. Such an asymmetric setup of the thermal boundary conditions is analysed via a numerical solution of the linear stability eigenvalue problem. The linear stability analysis is developed for three–dimensional normal modes of perturbation showing that the transverse modes are the most unstable. The destabilising effect of the non-Newtonian shear–thinning character of the fluid is also demonstrated as compared to the behaviour displayed, for the same flow configuration, by a Newtonian fluid.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

We construct families of ground state representations of the U(1)-current net and of the Virasoro nets Vir_c with central charge c ≥ 1. We show that these representations are not covariant with respect to the original dilations, and those on the U(1)-current net are not solitonic. Furthermore, by going to the dual net of with respect to the ground state representations of Vir_c, one obtains possibly new family of Möbius covariant nets on S¹.

In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

A Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a debilitating chronic disease of unknown aetiology under growing interest now in view of the increasingly recognized post-COVID syndrome as a new entity with similar clinical presentation. We performed the first cross-sectional study of ME/CFS in community population in Russia and then described and compared some clinical and pathophysiological characteristics of ME/CFS and post-COVID syndrome as neuroimmune disorders. Of the cohort of 76 individuals who suggested themselves suffering from ME/CFS 56 subsequently were confirmed as having CFS/ME according to ≥1 of the 4 most commonly used case definition. Of the cohort of 14 individuals with post-COVID-19 syndrome 14 met diagnostic criteria for ME/CFS. The prevalence of clinically expressed and subclinical anxiety and depression in ME / CFS and post-COVID ME/CFS did not differ significantly from that in healthy individuals. Severity of anxiety / depressive symptoms did not correlate with the severity of fatigue neigther in ME / CFS nor in post-COVID ME/CFS, but the positive correlation was found between the severity of fatigue and 20 other symptoms of ME / CFS related to the domains of “post-exertional exhaustion”, “immune dysfunction”, “sleep disturbances”, "dysfunction of the autonomic nervous system", "neurological sensory / motor disorders" and "pain syndromes". Immunological abnormalities were identified in 12/12 patients with ME / CFS according to the results of laboratory testing. The prevalence of postural orthostatic tachycardia assessed by the active standing test was 37.5% in ME / CFS and 75.0% in post-COVID ME/CFS (the latter was higher than in healthy controls, p = 0.02) There was a more pronounced increase in heart rate starting from the 6th minute of the test in post-COVID ME/CFS compared with the control group. Assessment of the functional characteristics of microcirculation by laser doppler flowmetry revealed obvious and very similar changes in ME/CFS and post-COVID ME/CFS compared to the healthy controls. The identified pattern corresponded to the hyperemic form of microcirculation disorders, usually observed in acute inflammatory processes or in deficiency of systemic vasoconstriction influences.

Tephra plumes can cause a significant hazard for surrounding towns, infrastructure, and air traffic. The current work presents the use of a small and compact X-band Multi-Parameter (X-MP) radar for the remote tephra detection and tracking of two eruptive events at Merapi Volcano, Indonesia, in May and June 2018. Tephra detection was done by analysing the multiple parameters of radar: copolar correlation and reflectivity intensity. These parameters were used to cancel unwanted clutter and retrieve tephra properties, which are grain size and concentration. Real-time spatial and temporal forecasting of tephra dispersal was performed by applying an advection scheme (nowcasting) in the manner of Ensemble Prediction System (EPS). Cross-validation was done using field-survey data, radar observations, and Himawari-8 imagery. The nowcasting model computed both the displacement and growth and decaying rate of the plume based on the temporal changes in two-dimensional movement and tephra concentration, respectively. Our results with ground-based data, where the radar-based estimated grain size distribution fell within the range of in-situ data. The uncertainty of real-time forecasted tephra plume depends on the initial condition, which affects the growth-and decaying rate estimation. The EPS improves the predictability rate by reducing the number of missed and false forecasted events. Our findings and the method presented here are suitable for early warning of tephra fall hazard at the local scale.

An interesting physical phenomenon was recently observed when a fresh-water basin is covered by a thin ice film that has properties similar to that of a rubber membrane. Surface waves can be generated under the action of wind on the air-water interface that contains an ice film. The modulation property of hydro-elastic waves (HEWs) in deep water covered by thin ice film blown by the wind with a uniform vertical profile is studied here in terms of the air-flow velocity versus a wavenumber. The modulation instability of HEWs is studied through the analysis of coefficients of the nonlinear Schrödinger (NLS) equation with the help of the Lighthill criterion. The NLS equation is derived using the multiple scale method in the presence of airflow. It is demonstrated that the potentially unstable hydro-elastic waves with negative energy appear for relatively small wind speeds, whereas the Kelvin–Helmholtz instability arises when the wind speed becomes fairly strong. Estimates of parameters of modulated waves for the typical conditions are given.

Ankle sprains are exceedingly common injuries in both athletes and general population. They account for 10 to 30% of all sports injuries. Although the vast majority of lateral ankle ligamentous injuries respond successfully to conservative management, the absolute number of those that progress to chronic lateral ankle instability (CLAI) remains considerably important. This condition is characterized by persistent symptoms and may be associated with short-term and long-term complications and functional deficits. There is still a lack of ideal postoperative management of CLAI patients. Furthermore, an evidence-based rehabilitation phasing does not exist and most of the published studies regarding this subject suggest some protocols based on a wide variety of functional assessment scores and other modalities which are not accurate enough. Moreover, the literature that assesses the ability to return to work (RTW) and return to sport (RTS) in general population and athletes operated for CLAI shows most commonly aggregated results with global rates of RTW or RTS without describing a detailed timeline based on the readiness of patients to return to each level of activity. Although stress radiographs and MRI have been assessed as potential tools to improve postoperative management of CLAI patients, the first modality is limited by its low sensitivity to detect laxity and the second one by its static character and its inability to predict the healing process phase nor the mechanical properties of the repaired/reconstructed ligaments. Bioelectrical impedance, mechanical impedance and near-infrared spectroscopy are non-invasive methods of measurement that could be potential assessment tools to help surgeons improve the postoperative management of patients after CLAI surgery.

Mapping forest composition using multiseasonal optical time series is still challenging. Highly contrasted results are reported from one study to another suggesting that drivers of classification errors are still under-explored. We evaluated the performances of single-year Formosat-2 time series to discriminate tree species in temperate forests in France and investigated how predictions vary statistically and spatially across multiple years. Our objective was to better estimate the impact of spatial autocorrelation in the validation data on measurement accuracy and to understand which drivers in the time series are responsible for classification errors. The experiments were based on ten Formosat-2 image time series irregularly acquired during the seasonal vegetation cycle from 2006 to 2014. Due to lot of clouds in the year 2006, an alternative 2006 time series using only cloud-free images has been added. Thirteen tree species were classified in each single-year dataset based on the SVM algorithm. The performances were assessed using a spatial leave-one-out cross validation (SLOO-CV) strategy, thereby guaranteeing full independence of the validation samples, and compared with standard non-spatial leave-one-out cross-validation (LOO-CV). The results show relatively close statistical performances from one year to the next despite the differences between the annual time series. Good agreements between years were observed in monospecific tree plantations of broadleaf species versus high disparity in other forests composed of different species. A strong positive bias in the accuracy assessment (up to 0.4 of Overall Accuracy) was also found when spatial dependence in the validation data was not removed. Using the SLOO-CV approach, the average OA values per year ranged from 0.48 for 2006 to 0.60 for 2013, which satisfactorily represents the spatial instability of species prediction between years.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

This study aims to tackle the challenge of high noise levels on balconies while preserving natural ventilation. Eight innovative balcony designs, incorporating elements like diffuser edges, undulating ceilings, Helmholtz resonators, grooves, or sound traps, were evaluated via finite element (FE) modeling. The extensive FE studies involved about 10 million elements per analysis case. Results showed that a standard balcony with a front parapet wall could achieve a noise reduction of around 10 dBA, with the jagged ledge design providing an additional 2 dBA improvement. Adding protruded ledge designs led to higher insertion loss (IL) by up to 9.4 dBA, especially at higher stories. Having wall-embedded Helmholtz resonators improved IL by up to 1.5 dBA. The jagged ledge design consistently exhibited positive IL across a broad frequency range from 200 Hz to 2 kHz. Combining beneficial balcony ceilings and wall ledges significantly reduced noise across lower and higher frequency ranges. Front jagged and full wavy ceilings offered positive IL throughout different storeys, proving their effectiveness against human vocal range. This study found that jagged ledge and front jagged ceiling designs, effective across various balcony heights, are viable options for improving balcony noise mitigation, providing valuable insights for architects and designers seeking practical solutions for outdoor noise reduction.

Spinal cord injuries (SCI) can result in sensory and motor dysfunctions, which were long-considered permanent. Recent advancement in electrical neuromodulation has been proven to restore sensorimotor function in people with SCI. These stimulation protocols, however, were mostly invasive, expensive, and difficult to implement. In this study, transcutaneous electrical stimulation (tES) was used to restore over-ground walking of an individual with 21 years of chronic paralysis from a cervical SCI. After a total of 66 weeks of rehabilitation training with tES, which included standing, functional reaching, reclined sit-up, treadmill walking and active biking, significant improvement in lower-limb volitional movements and overall light touch sensation were shown by International Standards for Neurological Classification of Spinal Cord Injury (ISNCSCI) score. By the end of the study, the participant could walk in a 4-meter walking test with the aid of a walking frame and ankle foot orthoses. The success in the sensorimotor recovery of our study participant sheds light on the future of non-invasive neuromodulation treatment for SCI paralysis.

Recent advances in open data initiatives allow us to free access to a vast amount of open LiDAR data in many cities. However, most of these open LiDAR data over cities are acquired by airborne scanning, where the points on façades are sparse or even completely missing due to the viewpoint and object occlusions in the urban environment. Integrating other sources of data, such as ground images, to complete the missing parts is an effective and practical solution. This paper presents an approach for improving open LiDAR data coverage on building façades by using point cloud generated from ground images. A coarse-to-fine strategy is proposed to fuse these two different sources of data. Firstly, the façade point cloud generated from terrestrial images is initially geolocated by matching the SFM camera positions to their GPS meta-information. Next, an improved Coherent Point Drift algorithm with normal consistency is proposed to accurately align building façades to open LiDAR data. The significance of the work resides in the use of 2D overlapping points on the outline of buildings instead of limited 3D overlap between the two point clouds and the achievement to a reliable and precise registration under possible incomplete coverage and ambiguous correspondence. Experiments show that the proposed approach can significantly improve the façades details of buildings in open LiDAR data and improving registration accuracy from up to 10 meters to less than half a meter compared to classic registration methods.

An 8-month-old, 3.4 kg, castrated male Toy Poodle was referred for progressive tetraparesis and respiratory disorder without a history of trauma. Diagnostic imaging, including dynamic CT and MRI, revealed concurrent atlanto-occipital dislocation (AOD) and atlantoaxial instability (AAI) with spinal cord compression. This case was unique due to its congenital nature and the absence of trauma. The surgical intervention involved precise removal of the C1 vertebra's ventral articular facet, which was compressing on the spinal cord, attributed to its fixed and malaligned position within the atlantooccipital joint. Following facetectomy, the stabilization of the occipital bone to the C2 vertebra was achieved by screws, wire, and polymethyl methacrylate. Postoperative recovery was monitored with CT and radiographs, showing successful decompression and gradual improvement in gait, despite mild residual ataxia. The dog experienced postoperative complications with screw loosening at 114 days, which was managed successfully by extracting the problematic screws. Postoperatively, the dog showed a near-normal gait and experienced no pain through 21 months of monitoring. This case represents the first report of concurrent congenital AOD and AAI treated with ventral surgical approach, contributing new insights to the understanding and management of such complex cranio-cervical junction disorders in veterinary neurosurgery.

The art work of this present paper is to show properly conditions and aspects to reach stability in the process control, as also to avoid instability, by using digital PID controllers, with the intention of help the industrial community. The discussed control strategy used to reach stability is to manipulate variables that are directly proportional to their controlled variables. To validate and to put the exposed principles into practice, it was done two simulations of a continuous fermentation tank process start-up with the yeast strain S. Cerevisiae NRRL-Y-132, in which the substrate feed stream contains different types of sugar derived from cane bagasse hydrolysate. These tests were carried out through the resolution of conservation laws, more specifically mass and energy balances, in which the fluid temperature and level inside the tank were the controlled variables. The results showed the facility in stabilize the system by following the exposed proceedings.

This paper proposes and demonstrates, in full scale, a novel type of energy geostructure (“the Climate Road”) that combines a ground source heat pump (GSHP) with a sustainable urban drainage system (SUDS) by utilizing the gravel roadbed simultaneously as energy source and rainwater retarding basin. The Climate Road measures 50m x 8m x 1m (length, width, depth) and has 800 m of geothermal piping embedded in the roadbed, serving as the heat collector for a GSHP that supplies a nearby kindergarten with domestic hot water and space heating. Model analysis of operational data from 2018-2021 indicates sustainable annual heat production levels around 0.6 MWh per meter road, with a COP of 2.9-3.1. The continued infiltration of rainwater to the roadbed increases the amount of extractable heat by an estimated 17% compared to the case of zero infiltration. Using the developed model for scenario analysis we find that draining rainwater from three single family houses and storing 30% of the annual heating consumption in the roadbed, increases the predicted extractable energy by 56% compared to zero infiltration with no seasonal energy storage. The Climate Road is capable of supplying three single family houses with heating, cooling and rainwater management year-round.

’Lockdown’ periods in response to COVID-19 have provided a unique opportunity to study the impacts of economic activity on environmental pollution (e.g. NO2, aerosols, noise, light). The effects on NO2 and aerosols have been very noticeable and readily demonstrated, but that on light pollution has proven challenging to determine. The main reason for this difficulty is that the primary source of nighttime satellite imagery of the earth is the SNPP-VIIRS/DNB instrument, which acquires data late at night after most human nocturnal activity has already occurred and much associated lighting has been turned off. Here, to analyze the effect of lockdown on urban light emissions, we use ground and satellite data for Granada, Spain, during the COVID-19 induced confinement of the city’s population from March 14 until May 31, 2020. We find a clear decrease in light pollution due both to a decrease in light emissions from the city and to a decrease in anthropogenic aerosol content in the atmosphere which resulted in less light being scattered. A clear correlation between the abundance of PM10 particles and sky brightness is observed, such that the more polluted the atmosphere the brighter the urban night sky. An empirical expression is determined that relates PM10 particle abundance and sky brightness at three different wavelength bands.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

There is a continuous growth of heat pump installations in residential buildings in Germany. The heat pumps were not only used for space heating and domestic hot water consumption but also to offer flexibility to the grid. the high coefficient of performance and the low cost of heat storages made the heat pumps an optimal candidate for the power to heat applications. Thus, several questions are raised about the optimal integration and control of the heat pump system with buffer storages to maximize its operation efficiency and minimize the operation costs. In this paper, an experimental investigation is performed to study the performance of a ground source heat pump (GSHP) with a combi-storage under several configurations and control factors. The experiments were performed on an innovative modular testbed that is capable of emulating a ground source to provide the heat pump with different temperature levels at different times of the day. Moreover, it can emulate the different building loads such as the space heating load and the domestic hot water consumption in real-time. The data gathered from the testbed and different experimental studies were used to develop a simulation model based on Modelica that can accurately simulate the dynamics of a GSHP in a building. The model was validated based on different metrics. Energetically, the difference between the developed model and the measured values was only 3.08\% and 4.18\% for the heat generation and electricity consumption, respectively.

Translational rockslides caused by toe excavation are one of the commonly seen geohazards in mountainous regions due to line traffic construction. Quantifying their failure extension length (FEL) and travel distance are of significant interest as well as huge challenges in landslide hazard assessment. In this paper, a simple criterion is proposed for predicting these two factors based on the principles of rigid body limit equilibrium and kinetic energy theorem. Further, the proposed criterion is validated against the field observations and numerical results with a practical case of the Xinjianan landslide, a medium-sized translational rockslide that occurred in 2013 in Nanchuan District, Chongqing. The findings indicate that a tiny discrepancy can be found in FEL between the field observations and the proposed criteria, while this discrepancy could be considerable in travel distance between different methods. However, the relative discrepancies all fall within 20%, deemed acceptable.

Functional ankle instability (FAI) results from multiple ankle sprains, causing a perceived sense of joint instability due to muscle and ligament imbalances. Neuromuscular training (NMT) is employed to enhance ankle stability in individuals with FAI. The study included 24 male university students with FAI, who underwent ankle NMT on three surfaces. OpenSim musculoskeletal model analyzed the effects on ankle muscle activity, kinetics, and kinematics. Utilizing repeated measures analysis of variance (ANOVA) and one-dimensional statistical non-parametric mapping (SNPM1d) to identify distinctions between training surfaces. NMT on foam cushion (FC) significantly enhanced tibialis anterior (TA) and gastrocnemius medial (GM) activation during walking compared to level-ground (LG) and artificial turf (AT) (p&lt;0.05). However, no differences observed for peroneus longus (PL), gastrocnemius lateral (GL), and peak ankle plantarflexion (PF). During jogging and fast running, post FC training increased TA, PL, GM, GL activation, and peak ankle PF moment (p&lt;0.05). Additionally, post FC training, subtalar mobility was significantly reduced (p&lt;0.05), and ankle joints exhibited greater dorsiflexion (DF) angles during jogging and fast running (p&lt;0.05). Consequently, selecting FC for short-term ankle NMT proves more advantageous in enhancing ankle stability among individuals with FAI, yielding a more positive impact on FAI improvement.

: Two-dimensional instability of a horizontal layer of boiling liquid with a finite height is experimentally studied. In this layer, “vapor columns” rose at the corners of a square rectangular grid. The symmetry of “vapor column” location on the heating surface is considered. The model considers the approach to the boiling crisis in terms of both developed nucleate boiling and transitional boiling (the Zuber problem). When dealing with developed nucleate boiling, the layer of boiling liquid is considered in calculations as an isotropic homogeneous system (foam). It is shown how the conditions on the heating surface (capillary-porous coating) affect external hydrodynamics of the liquid layer and, ultimately, the value of the critical heat flux. The calculation ratio obtained by approaching the boiling crisis with regard to developed nucleate boiling takes into account the dependence of the critical heat flux on the void fraction of the boiling liquid layer. A new solution to the boiling crisis problem is proposed when approaching the crisis from the point of transitional boiling (the Zuber problem). This new solution eliminates some shortcomings of the classical problem (in particular, the void fraction of the layer corresponds to the experiments).

Mandatory fortification of food with the synthetic folic acid (FA) was instituted in 1998 to reduce the incidence of neural tube defects. Adequate folate status is correlated with numerous health benefits. However, elevated consumption of FA is controversially associated with deleterious effects on health. We previously reported that excess FA mimicked folate depletion in a lymphoblastoid cell line. To explore the impact of FA intake from fortified food, we conducted an observational human study on 33 healthy participants aged 18-40 not taking any supplements. Food intake, anthropomorphic measurements, and blood samples were collected and analyzed. Our results show that individuals belonging to the highest tertile of folic acid intake, as well as ones with the highest folic acid to total folate intake ratio (FAR), display a significantly greater incidence of lymphocyte genomic damage. A decrease in global DNA methylation is observed in the highest tertile of FAR compared to the lowest (P=0.055). A downward trend in the overall gene expression of select DNA repair and one carbon cycle genes (MGMT, MLH1, UNG, MTHFR, MTR) is noted with increased folate status and FA intake. These results provide supporting evidence that high consumption of FA from fortified foods can precipitate genomic instability in peripheral lymphocyte in-vivo.

Researches are moving to iron and ammonia elimination from ground water. Here, we are using poly acrylic–poly acrylamide hydrogel which grafted with 3-chloroaniline. This copolymer was synthesized by addition polymerization. Effect of agitation time, dosage and adsorbents temperature on the removal process sensitivity has been investigated. The copolymer was described experientially and theoretically. Isothermal, kinetic adsorption models and were discussed. This hydrogel could be regenerated efficiently (98.3%removal of iron and 100% removal of ammonia). Density functional theory DFT method using B3LYP/6-311G(d,p),LANL2DZ level of the theory were managed to investigate stationary states of grafted co-polymer and the complexation energy of the hydrogel with the studied cations. NBO analysis is using DFT to investigate the negative centers on the hydrogel. The complexation energy showed selectively of hydrogel to studied cations.

Postural instability (PI) in Parkinson’s disease (PD) exposes patients to increased risk of falls (RF). Although dopaminergic therapy and deep brain stimulation (DBS) improve motor performance in advanced PD patients, their effects on PI and RF are not clear. PI and RF were assessed by a stabilometric platform in 6 advanced PD patients. Patients were evaluated on and off dopaminergic medication and four DBS conditions: bilateral-DBS, DBS of the more- or less-affected side and DBS-off. Dopaminergic medication alone worsened PI and RF, DBS alone worsened RF, and no medication/DBS combination produced an improvement in postural control with respect to the OFF-medication/DBS-off condition. When ON-medication, PI and RF significantly improved after turning the DBS on, regardless of medication condition. Among DBS conditions, bilateral-DBS provided the maximal improvement of PI and RF when ON medication, and minimal worsening of PI and RF when OFF medication, whereas patients performed worse when in most-affected side DBS condition. These results can help in developing the best therapeutic strategy for postural disorders in patients with advanced PD.

The holy town of Joshimath, gateway to the India-China border and religious places like Badrinath, Hemkunt Sahab, Valley of flowers in the Uttarakhand state of India experienced cracks in many of the residential and commercial buildings in the month of November-December 2022 which created panic and relocation of people. The reason(s) for the subsidence is still not known but using the InSAR technology and data from Sentinel-1, SAR data for the region was processed using HyP3 and MintPy for January-December 2022 to understand when the phenomenon started and how much uplift/subsidence the area has underwent in the last one year, as no such study is available till today. The entire town can be classified into two zones with respect to the annual subsidence values. Severe subsidence has been observed in the North and East regions whereas most of the southern region experienced moderate to low subsidence. Since the town is built on the debris of an old landslide, the subsidence may be attributed to the change in the course of the underground water channels due to heavy and continuous construction happening in the region and also due to drop in the water table. The results shows that the subsidence in the region was ongoing since June (from January till May, almost negligible vertical movement was recorded) which accelerated after September (when an uplift was recorded which lasted till October), while the subsidence peaked in the month of December with recorded subsidence of as much as 10 cm in some areas located around the Joshimath town, where most of the residential and commercial buildings are located.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

Coffee is regarded as the highly consumed beverage throughout the world and has established a key spot in the world economy as an important commodity for trading. In general, they are produced by brewing their roasted and ground beans, which release aromatic coffee; as well as produce an equivalent amount of spent coffee grounds (SCG). Previously, they were discarded as wastes or used as natural pest repellent or garden fertilizer; however, in recent times, are valorized into biofuels owing to their high calorific value. In fact, SCG briquettes have gained wide attention for supplying energy renewably, especially to the rising energy demand; and also have been identified as an effective measure to reduce their pollution. With this in mind, this present chapter focuses on reviewing the availability and chemistry involved in these SCG wastes, pre-treatments and preparations required for their briquetting, compacting techniques followed, and fuel characteristics of their briquettes, from various available works of literature. Here, their availability showcases the amount of SCG wastes generated with respect to time and consumption, wherein understanding their chemistry helps in deciding the pre-treatments necessary for their briquetting. Meanwhile, preparation techniques briefs about the necessary pre-treatments undertaken before compaction by different researchers; and the fuel characteristics define the physicochemical and mechanical properties of their briquettes, developed using various compaction methods. Besides, combustion behaviors of these briquettes are explained in terms of their burning characteristics and emission levels, as reported in literatures; which help in deciding their suitability as a replacement for existing fossil coal. Eventually, all the reported data were in accordance with their permissible standards and suggested these SCG as a highly renewable solid biofuel.

The airport ground handling services (AGHS) equipment supplier selection problem involves a safety guarantee on the part of the AGHS company that carries out the daily work. AGHS company can prevent aircraft damage and delays in airlines schedules, and ensure reliable and high-quality ground handling service. In our research, we developed an AGHS equipment supplier selection model based on the analytic hierarchy process and an AHP weighted fuzzy linear programming approach, and we solved the AGHS equipment supplier’s selection problem. The main objective of this article is to create an AHP and AHP-FLP decision model in order to help the AGHS company authorities select the best AGHS equipment supplier. The practical application in AGHS equipment supplier selection decisions can be interpreted as demonstrating that the proposed model provides knowledge and practical value for the AGHS industry.

In our study we used the data set on morphimetric traits in beetles species. It has been constantly replenishing for 20 years by the samples, received from different regions of Russia and abroad. In this case we have selected data on nine species for which the left and right sides had been measured and fluctuating asymmetry (FA) could be estimated. The samples were from 6 provinces of Russia and Belarus, which ranged in 3 degrees in latitude and 57 degrees in longitude and included more than 150 plots in different types of biotopes. FA was assessed according to the standard method in 5265 specimen in one dimensional trait and one - meristic. ANOVA showed that biotope, species and their interaction affected FA in both traits, that is different species reacted differently to biotope type. In uncommon biotopes (according to accepted in carabidology classification) FA was increased. In forest species the negative relationship between FA in dimensional and meristic traits in the range in biotopes was revealed. In those species only FA values were higher in males than in females. In generalist species FA varieв similarly in both sexes and in both traits being the highest in open biotopes. In eudomonant of arable lands biotopes – Poecilus cupreus – the highest values of FA were recorded in the meadows, being about equal in all types of crops.

The study conducts a comparative analysis of solar radiation estimation methods, assessing the efficacy of the Heliosat-2 algorithm against ground measurements across seven distinct countries: Netherlands, Spain, Japan, Namibia, South Africa, Saudi Arabia, and India. To achieve this, it utilizes two distinct satellite data sources—Himawari-8 for Japan and Metosat Second Generation-MSG for the rest of the countries—spanning the years Jan 2022 to April 2024. A robust methodology for determining albedo parameters specific to Heliosat-2 was developed. During cloudy days, the estimates provided by Heliosat-2 generally exceeded the ground measurements in all the countries. Conversely, on clear days, there was a tendency for underestimation, as indicated by the median value of the mean bias (MB) across most of the countries. The Heliosat-2 model slightly underestimates daily radiation values, with a median MB ranging from −27.5 to +10.2 W.m⁻². Notably, the median root mean squared error (RMSE) on clear days is significantly lower, with values ranging from 24.8 to 108.7 W.m⁻², compared to cloudy days where RMSE values lie between 75.3 and 180.2 W.m⁻². In terms of R² values, both satellites show a strong correlation between the estimated and actual values, with a median value consistently above 0.86 on a monthly scale and over 92% of daily data points falling within ±2 standard deviation.

A Mw7.8 earthquake struck Turkey on February 6, 2023, causing severe casualties and economic losses. This paper investigates the characteristics of strong ground motion and seismogenic fault of the earthquake. We collected and processed the strong ground motion records of 379 stations using Matlab, SeismoSignal and Surfer software, and obtained the peak ground acceleration (PGA) contour map. We analyzed the near-fault effect, the fault locking segment effect and the trampoline effect of the earthquake based on the spatial distribution of PGA, the fault geometry and slip distribution. We found that the earthquake generated a very strong ground motion concentration effect in the near-fault area, with the maximum PGA exceeding 2000cm/s2. However, the presence of fault locking segments influenced the spatial distribution of ground motion, resulting in four significant PGA high-value concentration areas at a local dislocation, a turning point and the end of the East Anatolian Fault. We also revealed for the first time the typical manifestation of the trampoline effect in this earthquake, which was characterized by a large vertical acceleration with the positive direction significantly larger than the negative direction. This paper provides an important reference for understanding the seismogenic mechanism, damage mode, characteristics and strong earthquake law of Turkey earthquake.

Tumorigenesis is a complex biological phenomenon that includes extensive genetic and phenotypic heterogeneities and complicated regulatory mechanisms. In the recent few years, our studies demonstrate that tumor-initiating cells are similar to neural stem/progenitor cells in regulatory networks, tumorigenicity and pluripotent differentiation potential. In the review, I will make further discussion on these observations and propose a rule of cell biology by integrating these findings with evidence from developmental biology, tumor biology and evolution, which suggests that neural stemness underlies two coupled cell properties, tumorigenicity and pluripotent differentiation potential. Tumorigenicity and phenotypic heterogeneity in tumor is a result of acquirement of neural stemness in cells. The neural stemness property of tumor-initiating cells can hopefully integrate different concepts/hypotheses underlying tumorigenesis. Neural stem cells/neural progenitors and tumor-initiating cells share regulatory networks; both exhibit neural stemness, tumorigenicity and differentiation potential; both are dependent on expression or activation of ancestral genes (the atavistic effect); both rely primarily on aerobic glycolytic metabolism; both can differentiate into various cells or tissues that are derived from three germ layers, resembling severely disorganized or more severely degenerated process of embryonic development; both are enriched in long genes with more splice variants that provide more plastic scaffolds for cell differentiation, etc. The property of neural stemness might be a key point to understand tumorigenesis and pluripotent differentiation potential, and possibly explain certain pathological observations in tumors that have been inexplicable. Therefore, behind the complexity of tumorigenesis might be a general rule of cell biology, i.e., neural stemness represents the ground state of cell tumorigenicity and pluripotent differentiation potential.

The Late Bronze Age on the territory of Southern Transurals is represented by two major archeological cultures: Srubnaya and Andronovskaya (Alakul culture and Fyodorovskaya – type). Their interaction of constitutes a special mix of material cultures which preserves common features of two independent, Srubnaya and Andronovskaya cultures, but also creates novel local material features. These cultural groups are also known to have brought to the region the technology of bronze production. This is evidenced, amongst others, by the proximity of the largest copper mining in the region, Kargaly mines Chernykh (2002). New methods to produce ceramics and to work bones were also developed, combining two traditions, coming from Srubnaya and Andronovskaya cultures respectively. Importantly, the features of these cultures are commonly encountered together in a single cultural horizon across the distribution ares. These diffusion processes took place in a vast area (more than 120,000 km²) andwere reflected in archeological micro-district of the Urshak river basin. We present here the most recent results of the scientific examination of the Late Bronze Age settlements in southern Transurals and attempt to address a peculiar cultural co-habitation of two distinct cultural groups in this region. We also discuss their synchronism based on absolute dates and elaborate on this cultural syncretism in the entire territory of the Volga-Ural region.

Background/Objectives Recurrent shoulder instability following Bankart lesion repair often necessitates surgical revision. Identified risk factors include young age, glenoid bone loss, and off-track Hill-Sachs lesions. This systematic review aims to understand failure rates of arthroscopic revision Bankart repair and if these aforementioned factors influence its success. Methods Following PRISMA guidelines, this systematic review, registered on PROSPERO, included twenty-four articles. Two independent reviewers assessed eligibility across three databases, focusing on recurrent instability as the primary endpoint, while also noting functional measures, adverse events, revision operations, and return-to-sport rates when available. Results Key surgical techniques for recurrent instability post-Bankart repair were identified, with revision arthroscopic Bankart being the most common (685/1032). Despite generally endorsed effectiveness, recurrence rates have increased over the past four years. Comparative analysis revealed significantly lower recurrence for open Latarjet compared to revision arthroscopic Bankart (p

Emergency control load-shedding is a key solution to prevent blackouts in the power system. This paper proposed a new model of emergency controls load shedding based on the fast identification of the unstable state of the power system. K-means clustering algorithm divided the instability mode into the clusters. The results of analysis of this cluster were used as the basis for classification control. Building load shedding strategies is consisted of the pre-designed rules based on AHP algorithm. When the recognition of the power system “instability” is detected, the signal of load shedding control is triggered immediately, therefore the decision time is greatly shortened comparing to the traditional methods. The effectiveness of the proposed method was tested on the IEEE 39-bus to overcome the limitations of the last traditional methods.

The capabilities of autonomous mobile robotic systems have been steadily improving due to recent advancements in computer science, engineering, and related disciplines such as cognitive science. In controlled environments, autonomous robots have been able to achieve relatively high levels of autonomy. In more unstructured environments, however, the realisation of autonomous mobile robots remains challenging due to limitations in the robots’ external environment understanding. Many autonomous mobile robots use classical, learning-based or hybrid approaches for navigation. The classical navigation approach typically includes robot perception, localisation, environmental mapping, path planning and motion control stages. More recent learning-based methods may replace the complete navigation pipeline or selected stages of the classical approach. For effective deployment, autonomous robots need to be able to understand their external environments at a sophisticated level according to their intended applications. Therefore, in addition to robot perception, scene analysis and higher-level scene understanding (e.g., traversable/non-traversable, and rough or smooth terrain) are required for autonomous robot navigation in unstructured outdoor environments. A wide number of alternative approaches have been proposed in recent years to attempt to address these scene understanding requirements. This paper provides a comprehensive review and critical analysis of these methods in the context of their applications to the problems of robot perception and scene understanding in unstructured environments, and the related problems of localisation, environment mapping and path planning. State-of-the-art sensor fusion methods and multimodal scene understanding approaches are also discussed and evaluated within this context. The paper concludes with an in-depth discussion regarding the current state of the autonomous ground robot navigation challenge in unstructured outdoor environments and the most promising future research directions to overcome these challenges.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

Ground-based infrared cameras can be used effectively and safely to provide quantitative information about small to moderate-sized volcanic eruptions. This study describes an infrared camera that has been used to measure emissions from Mt Etna and Stromboli (Sicily, Italy) volcanoes. The camera provides calibrated brightness temperature images in a broadband (8--14 µm) channel that is used to determine height, plume ascent rate and volcanic cloud/plume temperature and emissivity at temporal sampling rates of up to 1 Hz. The camera can be operated in the field using a portable battery and includes a microprocessor, data-storage and WiFi. The processing and analyses of the data are described with examples from the field experiments. The updraft speeds of the small eruptions at Stromboli are found to decay with a timescale of $\sim$10 min and the volcanic plumes reach thermal equilibrium within $\sim$2 min. A strong eruption of Mt Etna on 1 April 2021 was found to reach $\sim$9 km, with ascent speeds of 10--20 ms$^{-1}$. The plume, mostly composed of water vapour and SO$_2$ gas became bent over by the prevailing winds at high levels.

Poly (Lactic Acid) (PLA) / Ground Tire Rubber (GTR) blends using Dicumyl peroxide (DCP) as a crosslinking agent were prepared as a route to recycle wastes rubber from the automotive industry. The GTR were exposed to grinding and exhibited mechanical damage, traduced at the rubber network scale by chains scission and/or chemical cross-links breakage. Such damage is accompanied by a decrease of 80% of the rubber chains network density of the initial tire buffing but found independent on the type of grinding (cryogenic, dry ambient) or on the GTR size (from <400 µm to <63 µm). Moreover, the finest sieved GTR contain the largest the amount of reinforcing elements (carbon black, clay) that can be advantageously used in PLA/GTR blends. The melt-blending of these finest GTR particles obtained by cryo-grinding at an amount of 15 wt.% and in presence of the crosslinking agent (DCP), resulted in an optimum improvement of the ductility, energy at break and impact strength of the PLA/GTR blends as compared to neat PLA, while maintaining its stiffness. The results were attributed to (i) the good dispersion of the fine GTR particles into the PLA matrix, (ii) the partial re-crosslinking of the GTR particles and co-crosslinking at PLA/GTR interface and (iii) the presence of reinforcing carbon black into the GTR particles and clay particles dispersed into the PLA matrix.

The pile foundation in the permafrost region is in a negative temperature environment, so the concrete is affected by the negative temperature of the surrounding soil.It not only affects the formation of concrete strength, but also leads to engineering quality accidents in serious cases.Based on the actual measurement of temperature at different strata depths and the comprehensive consideration of surface temperature, terrestrial heat flux and other parameters, the law curve of temperature change along depth in Greater Khingan is established.The calculated results of the curve are consistent with the measured results of ground temperature.The results show that the variation trend of ground temperature along the strata depth at different monitoring sites is basically the same. From June to November, the ground temperature at different depths tends to be constant.From December to May, the ground temperature at any depth within the depth range of 0 to 5.5m follows the law of the cosine function.Below 5.5m, the earth temperature no longer varies with depth.The research results can be used as reference for pile foundation construction under negative temperature environment.

This paper describes the physico-chemical study of the adsorption of dysprosium (Dy³⁺) in aqueous solution onto two types of activated carbons synthesized from spent coffee ground. KOH activated carbon is a microporous material with a specific BET surface area of 2330 m²·g^-1 and pores with a diameter of 3.2 nm. Carbon activated with water vapor and N₂ is a solid mesoporous, with pores of 5.7 nm in diameter and a specific surface of 982 m²·g^-1. A significant dependence of the adsorption capacity on the solution pH was found, while it does not depend significantly neither on the dysprosium concentration nor on the temperature. A maximum adsorption capacity of 31.26 mg·g^-1 and 33.52 mg·g^-1 for the chemically and physically activated carbons, respectively, were found. In both cases, the results obtained from adsorption isotherms and kinetic study were better fit to a Langmuir model and a pseudo-second-order kinetics. In addition, thermodynamic results indicate that dysprosium adsorption onto both activated carbons is an exothermic, spontaneous and favorable process.

This paper deals with bistatic subsurface probing of a horizontally layered dielectric half-space by means of ultra-wideband electromagnetic pulses. A receiver collects reflections from the air-ground interface and from the gradients of dielectric permittivity in the half-space. This scenario is of interest for ground penetrating radar (GPR) applications. For the analytical description of the received signal, we developed and implemented a novel time-domain version of the coupled-wave Wentzel–Kramers–Brillouin approximation. Our solution is in very good agreement with finite-difference time-domain results, radically accelerates calculations, and effectively accounts for the protracted return signals observed in the lower part of the GPR spectrum. The paper includes results showing the application of the proposed technique to two case studies: in particular, the method was employed for the post-processing of experimental radargrams collected on Lake Chebarkul, in Russia, and to simulate GPR probing of the Moon surface, to detect smooth gradients of the dielectric permittivity in lunar regolith.

Accurate cloud quantification is essential in climate change research. In this work, we construct an automated computer vision framework by synergistically incorporating deep neural networks and finite sector clustering to achieve robust whole sky image-based cloud classification, adaptive segmentation, and recognition under intricate illumination dynamics. A bespoke YOLOv8 architecture attains over 95% categorical precision across four archetypal cloud varieties curated from extensive annual observations (2020) at a Tibetan highland station. Tailor-made segmentation strategies adapted to distinct cloud configurations, allied with illumination-invariant image enhancement algorithms, effectively eliminate solar interference and substantially boost quantitative performance even in illumination-adverse analysis scenarios. Compared with the traditional threshold analysis method, the cloud quantification accuracy calculated within the framework of this paper is significantly improved. Collectively, the methodological innovations provide an advanced solution to markedly escalate cloud quantification precision levels imperative for climate change research, while offering a paradigm for cloud analytics transferable to various meteorological stations.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

With the ever-increasing popularity of unmanned aerial vehicles and other platforms providing dense point clouds, filters for identification of ground points in such dense clouds are needed. Many filters have been proposed and are widely used, usually based on the determination of an original surface approximation and subsequent identification of points within a predefined dis-tance from such surface. We present a new filter, Multi-view and shift rasterization algorithm (MVSR) is based on a different principle, i.e., on the identification of just the lowest points in in-dividual grid cells, shifting the grid along both planar axis and subsequent tilting of the entire grid. The principle is presented in detail and compared both visually and numerically to other commonly used ground filters (PMF, SMRF, CSF, ATIN) on three sites with different ruggedness and vegetation density. Visually, the MVSR filter showed the smoothest and thinnest ground profiles, with ATIN the only filter performing comparably. The same was confirmed when comparing ground filtered by other filters with the MVSR-based surface. The goodness of fit with the original cloud is demonstrated by the root mean square deviations (RMSD) of the points from the original cloud found below the MVSR-generated surface (ranging, depending on site, between 0.6-2.5 cm). The MVSR filter performed outstandingly at all sites, identifying the ground points with great accuracy while filtering out the maximum of vegetation/above-ground points. The filter dilutes the cloud somewhat; in such dense point clouds, however, this can be perceived rather as a benefit than as a disadvantage.

With the ever-increasing popularity of unmanned aerial vehicles and other platforms providing dense point clouds, universal filters for accurate identification of ground points in such dense clouds are needed. Many filters have been proposed and are widely used, usually based on the determination of an original surface approximation and subsequent identification of points within a predefined distance from such surface. In this paper, we present a new filter. This Multi-view and shift rasterization algorithm (MVSR) is based on an entirely different principle, i.e., on the identification of just the lowest points in individual grid cells, shifting the grid along both planar axis and subsequent tilting of the entire grid – after each of these steps, one lowest point per cell is detected. The principle is presented in detail and compared both visually and numerically to other commonly used ground filters (PMF, SMRF, CSF, ATIN) on three sites with different ruggedness and vegetation density. Visually, the MVSR filter showed the smoothest and thinnest ground profiles, with ATIN the only filter performing comparably (although the profiles were somewhat thicker and not as complete as MVSR-acquired ground). The same was confirmed when comparing ground filtered by other filters with the MVSR-based surface. The goodness of fit with the original cloud is demonstrated by the root mean square deviations (RMSD) of the points from the original cloud found below the MVSR-generated surface (ranging, depending on site, between 0.6-2.5 cm). ATIN again performed closest to MVSR, with RMSDs of ground filtered points found above MVSR-based surface at individual sites ranging between 4.5-7.4 cm. The remaining filters performed comparable in the simplest flat area but poorly in rugged and much-vegetated sites, with RMSDs above the MVSR surface ranging at such sites from 21 to 95 cm. In conclusion, the novel filter presented in this paper performed outstandingly at all sites, identifying the ground points with great accuracy while filtering out the maximum of vegetation/above-ground points. The filter dilutes the cloud somewhat; in such dense point clouds, however, this can be perceived rather as a benefit than as a disadvantage.

Understanding the effect of horseshoe-surface combinations on hoof kinematics at gallop is relevant for optimising performance and minimising injury in racehorse-jockey dyads. This intervention study assessed hoof breakover duration in Thoroughbred ex-racehorses from the British Racing School galloping on turf and artificial tracks in four shoeing conditions: barefoot, aluminium-rubber composite (GluShu), aluminium and steel. Shoe-surface combinations were tested in a randomized order and horse-rider pairings (n=14) remained constant. High-speed video cameras (Sony DSC-RX100M5) filmed the hoof-ground interactions at 1000 frames per second. The time taken for a hoof marker wand fixed to the lateral hoof wall to rotate through an angle of 90 degrees during 384 breakover events was quantified using Tracker software. Data were collected for leading and non-leading front and hind limbs, at gallop speeds ranging from 23–56 km h-1. Linear mixed-models assessed whether speed, surface, shoeing condition or any interaction between these parameters (fixed factors) significantly affected breakover duration. Day and horse-rider pair were included as random factors and speed was included as a covariate. The significance threshold was set at p&lt;0.05. For all limbs, breakover times decreased as gallop speed increased (p&lt;0.0005), although a greater relative reduction in breakover duration for hindlimbs was apparent beyond approximately 45 km h-1. Breakover duration was longer on turf compared to the artificial surface (p≤0.04). In the non-leading hindlimb only, breakover duration was affected by shoeing condition (p=0.025) and an interaction between shoeing condition and speed (p=0.023). Future work seeks to relate these results to hoof accelerometer data.

Past exploration for U deposit in the Philippines discovered the mineralization of radioactive allanite in Palawan. The allanite occurs as sand component in the heavily populated beach of Erawan, San Vicente, Palawan. This work assessed the risks associated with the radionuclides in Erawan beach by in situ ground radiometric survey of K, U, and Th in 694 sampling points. Principal component analysis (PCA) and Pearson correlation coefficient were used to determine the similarity between the radionuclides and to identify other probable anthropogenic sources of radionuclides. Our results show that the mean activity concentrations of K (597.8 Bq kg^-1) and Th (93.15 Bq kg^-1) are equivalent to 1.5 and 3.1 times of the world average natural radioactivity levels in soil, respectively, while the mean U (34.7 Bq kg^-1) is similar to the world average. The mean radiological risk assessments like radium equivalent, gamma specific activity index, external hazard index, internal hazard index, absorbed gamma dose rate, annual effective dose equivalent, annual gonadal equivalent dose, and excess lifetime cancer risk are 213.96 Bq kg^-1, 0.78, 0.58, 0.67, 97.24 nGy h^-1, 119.25 µSv y^-1, 684.39 µSv y^-1, and 0.42 (10^-3), respectively. Th consistently correlated most to the risks. We attribute the occurrence of Th to the presence of allanite, K to fertilizer use for farming, and U to both the allanite and farming. The results of our study can provide important baseline data for future detailed studies or monitoring of the long-term effects of elevated radiation levels to the local population of Erawan.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

The instability of traveling pulses in nonlinear diffusion problems is inspected on the example of Gunn domains in semiconductors. Mathematically the problem is reduced to the calculation of the "energy" of the ground state in Schrödinger equation with a complicated potential. A general method to obtain the bottom-part spectrum of such equations based on the approximation of the potential by square wells is proposed and applied. Possible generalization of the approach to other types of nonlinear diffusion equations is discussed.