The optimization of guide vane closing schemes (OGVCS) of pumped storage hydro unit (PSHU) is the research field of cooperative control and optimal operation of pumped storage, wind power and solar power generation. This paper presents a OGVCS model of PSHU considering the rise rate of the unit rotational speed and the specific node pressure of each hydraulic unit, as well as various complicated hydraulic and mechanical constraints. OGVCS model is formulated as a multi-objective optimization problem to optimize conflictive objectives, i.e., unit rotational speed and water hammer pressure criteria. In order to realize the efficient solution of the OGVCS model, an enhanced multi-objective bacterial-foraging chemotaxis gravitational search algorithm (EMOBCGSA) is proposed to solve this problem, which adopts population reconstruction, adaptive selection chemotaxis operator of local searching strategy and Elite archive set to efficiently solve the multi-objective problem. Especially, novel constraints-handling strategy with eliminating and local search based on violation ranking is used to balance various hydraulic and mechanical constraints. Finally, simulation cases of complex extreme operating conditions (i.e., load rejection and pump outage) of ‘single tube-double units’ type PSHU system are conducted to verify the feasibility and effectiveness of the proposed EMOBCGSA in solving OGVCS problem. The simulation results indicate that the proposed EMOBCGSA can provide lower rise rate of the unit rotational speed and smaller water hammer pressure than other method established recently while considering various complex constraints in OGVCS problem.

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

The insuperable obstacle between gravity and quantum mechanics is their spacetimes. Introduction of a (quantum) quadratic form on a state Hilbert space and a (quantum) metric tensor in (3+1)D quantum spacetime solves the problem by providing a common spacetime for both gravity and quantum mechanics which helps further to develop an accurate and generalized form of quantum gravity, i.e., General Quantum Gravity. This formalism yields a (3+1)D pseudo-gravity first order quantum equation, which is technically more accurate than Schr\"odinger equation. A (quantum) Lorentz-like transformation is also possible to be developed in (3+1)D quantum spacetime. Instead of one common Einstein field equation to explain gravitational effects, this formalism yields two individual (quantum) Einstein field equations, namely, one for bosons and another for fermions. In this work, (quantum) metric tensor as well as quantum Riemann tensor, quantum Ricci tensor and quantum Ricci scalar all are found to be the objects of quantization. Apparently, these quantum Riemann tensor, quantum Ricci tensor and quantum Ricci scalar are also found to be multiplicatively renormalizable while all divergences of their higher orders vanish in (3+1)D quantum spacetime. Ultimately, General Quantum Gravity yields that: Quantum Mechanics and Theory of Special and General Relativity are inseparable and naturally inter-expressible for the (quantum) quadratic form and the (quantum) metric tensor in (3+1)D quantum spacetime.

This paper studied the combined influences of the hot streak and swirl on the cooling performances of the NASA C3X guide vane coated with or without TBCs. The results show that: (1) Even under uniform velocity inlet conditions, the hot streak core can be stretched as it impinges the leading edge which causes higher heat load on the suction side of the forward portion. (2) The swirl significantly affects circumferential and radial migration of the hot streak core in the NGV passage. On the passage inlet plane, positive swirl leads to a hotter tip region on the suction side. In comparison, negative swirl leads to a hotter hub region on the pressure side. (3) Under the influence of swirl, migration of coolant improve the coverage of film cooling close to the midspan, while in the regions close to the hub and tip end-wall, the overall cooling performance decrease simultaneously. (4) In the regions with enough internal cooling, the cooling effectiveness increment is always larger than that in other regions. Besides, the overall cooling effectiveness increment decreases on the region covered by film cooling for the coated vane, especially in the region with negative local heat flux.

Considering that cryptocurrencies are now present in practically every financial transaction because they are widely accepted as an alternate means of making payments and exchanging currencies, academics and economists have more opportunities to study cryptocurrency prices. Over the years, investors, traders and investment banks have found it difficult to predict the closing daily price of Ethereum due to its rapid price fluctuation. The daily closing price of cryptocurrency is essential to consider when trading or investing in Ethereum. This report focuses on carrying out a comparative study of the predictive capabilities of deep machine learning algorithms with a stacking ensemble modelling framework using daily historical observations of the price of Ethereum obtained from Coindesk, tweets extracted from Twitter ranging from the 1st of August 2022 to the 8th of August 2022 and other five covariates (closing price lag1, closing price lag2, noltrend, daytype and month) engineered from the closing price of Ethereum. Seven models are used to compute the forecasts for the daily closing price of Ethereum; these are the recurrent neural network, ensemble stacked recurrent neural network, gradient boosting machine, generalized linear model, distributed random forest, deep neural networks and stacked ensemble for gradient boosting machine, generalized linear model, distributed random forest and deep neural networks. The main evaluation metric used is the mean absolute error. According to MAE, RNN forecasts outperform the other model’s forecasts in this study, producing an MAE of 0.0309.

Entanglement is one of the most striking features in quantum systems. Today, quantum entanglement plays a vital role in quantum technology, the non-classical correlation of quantum entanglement is an important resource for quantum communication and quantum computing. Entanglement can be divided into two categories: between multi-particle systems and between various degrees of freedom in a single-particle system (intraparticle entangled states). This work first analogized the distinctions and connections between two kinds of entangled states. Then it designed three types of entanglement-swapping methods based on Bell state joint measurement, cross-Kerr medium, and linear optical elements for intraparticle entangled states by analogizing the entanglement swapping between multiple particles. Intraparticle entanglement swapping can be applied in super quantum dense encoding, quantum information transmission, and quantum teleportation. This work is beneficial for promoting the development of quantum information technologies.

In the last years, different biotechnological approaches were developed to reduce the indiscriminate use of chemical fertilizers and pesticides and enhance plant growth and health. The most attractive, safe, and environmentally mild alternatives include those based on plant beneficial microorganisms. After a long period of studies on isolation, selection, and characterisation of plant-beneficial microorganisms, the main lines of research have been oriented to optimising the fermentation processes to produce high-quality and large volumes of biomass/spores and their further formulation. However, further well-structured schemes for improvement of all main steps of the production of bio-formulates should be developed following the ideas based on “healthy soil-healthy plants-healthy humans”.

New setting is introduced to study “closing numbers” and “super-closing numbers” as optimal-super-resolving number, optimal-super-coloring number and optimal-super-dominating number. In this way, some approaches are applied to get some sets from (Neutrosophic)n-SuperHyperGraph and after that, some ideas are applied to get different types of super-closing numbers which are called by optimal-super-resolving number, optimal-super-coloring number and optimal-super-dominating number. The notion of dual is another new idea which is covered by these notions and results. In the setting of dual, the set of super-vertices is exchanged with the set of super-edges. Thus these results and definitions hold in the setting of dual. Setting of neutrosophic n-SuperHyperGraph is used to get some examples and solutions for two applications which are proposed. Both setting of SuperHyperGraph and neutrosophic n-SuperHyperGraph are simultaneously studied but the results are about the setting of n-SuperHyperGraphs. Setting of neutrosophic n-SuperHyperGraph get some examples where neutrosophic hypergraphs as special case of neutrosophic n-SuperHyperGraph are used. The clarifications use neutrosophic n-SuperHyperGraph and theoretical study is to use n-SuperHyperGraph but these results are also applicable into neutrosophic n-SuperHyperGraph. Special usage from different attributes of neutrosophic n-SuperHyperGraph are appropriate to have open ways to pursue this study. Different types of procedures including optimal-super-set, and optimal-super-number alongside study on the family of (neutrosophic)n-SuperHyperGraph are proposed in this way, some results are obtained. General classes of (neutrosophic)n-SuperHyperGraph are used to obtains these closing numbers and super-closing numbers and the representatives of the optimal-super-coloring sets, optimal-super-dominating sets and optimal-super-resolving sets. Using colors to assign to the super-vertices of n-SuperHyperGraph and characterizing optimal-super-resolving sets and optimal-super-dominating sets are applied. Some questions and problems are posed concerning ways to do further studies on this topic. Using different ways of study on n-SuperHyperGraph to get new results about closing numbers and super-closing numbers alongside sets in the way that some closing numbers super-closing numbers get understandable perspective. Family of n-SuperHyperGraph are studied to investigate about the notions, super-resolving and super-coloring alongside super-dominating in n-SuperHyperGraph. In this way, sets of representatives of optimal-super-colors, optimal-super-resolving sets and optimal-super-dominating sets have key role. Optimal-super sets and optimal-super numbers have key points to get new results but in some cases, there are usages of sets and numbers instead of optimal-super ones. Simultaneously, three notions are applied into (neutrosophic)n-SuperHyperGraph to get sensible results about their structures. Basic familiarities with n-SuperHyperGraph theory and neutrosophic n-SuperHyperGraph theory are proposed for this article.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Bell type inequalities are proven using oversimplified probabilistic models and/or counterfactual definiteness (CFD). If setting-dependent variables describing measuring instruments are correctly introduced none of these inequalities may be proven. In spite of this a belief in a mysterious quantum nonlocality is not fading. Computer simulations of Bell tests allow studying different scenarios how the experimental data might have been created. They allow also to generate outcomes of various counterfactual experiments such as repeated or simultaneous measurements performed in different settings on the same ‘’ photon-pair” etc. They allow reinforcing or relaxing CFD- compliance and /or to study the impact of various “photon identification procedures” mimicking those used in real experiments. Using a specific setting- dependent identification procedure data samples consistent with quantum predictions may be generated. It reflects an active role of instruments during the measurement process. Each setting dependent data samples are consistent with specific setting –dependent probabilistic models which may not be deduced using non-contextual local realistic or stochastic hidden variables. In this paper we discuss the results of these simulations. Since the data samples are generated in a locally causal way, these simulations provide additional strong arguments for closing the door on quantum nonlocality

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

We model the financial markets as a game and make predictions using Markov chains estimators. We extract the possible patterns displayed by the financial markets, define a game where one of the players is the speculator, whose strategies depend on his/hers risk-to-reward preferences, and the market is the other player, whose strategies are the previously observed patterns. Then we estimate the market’s mixed probabilities by defining Markov chains and utilizing its transitions matrices. Afterwards, we use these probabilities to determine which is the optimal strategy for the speculator. Finally, we apply these models to real-time market data to determine its feasibility. After all, we obtained a model for the financial markets that has an outstanding performance in terms of accuracy and profitability.

Considering the worldwide impact of heart failure, it is crucial to develop approaches that can help us comprehend its root cause and make accurate predictions about its outcome. This is essential for lowering the suffering and death rates connected with this widespread illness. Cardiomyopathies frequently result from genetic factors, and the study of heart failure genetics is advancing quickly. Dilated cardiomyopathy (DCM) is the most prevalent kind of cardiomyopathy, encompassing both hereditary and nongenetic abnormalities. It is distinguished by the enlargement of the left ventricle or both ventricles, accompanied by reduced contractility. The discovery of the molecular origins and subsequent awareness of the molecular mechanism is broadening our knowledge of DCM development. Additionally, it emphasizes the complicated nature of DCM and the necessity to formulate several different strategies to address the diverse underlying factors contributing to this disease. Genetic variations that can be transmitted from one generation to another can be a significant contributor to causing family or isolated DCM. Genetic variation also plays a significant role in determining susceptibility for acquired triggers for DCM. The genetic causes of DCM can have a diverse range of phenotypic expressions. It is crucial to select the most probable patients to have advantages from genetic testing. The purpose of this research is to emphasize the significance of identifying genetic DCM, the crucial relationships between genotype and phenotype, and the usefulness of genetic testing in the therapeutic care of both those affected and their relatives. This approach is expected to gain importance once treatment is guided by genotype-specific advice and disease-modifying medications.

This paper assessed rice farmers' perceptions of agricultural and irrigation practices through their choices. A survey was carried out among 278 rice farmers on five irrigation schemes in three agro-ecological zones of Togo, viz. the savannah region, the forest region and the coastal region. The sample of random respondents was selected from a list of rice farmers provided by the managers of these irrigated schemes. Data collected through face-to-face interviews using kobocollect software were analyzed with R 4.2 software, and the Pearson test was validated at the 5% level. The results showed that the socio-economic characteristics of the rice growers, such as access to agricultural credit, experience, non-agricultural activities, membership of a rice growers' cooperative, gender, level of education and training in growing irrigated rice, and farm labor, significantly influenced the choice of agronomic practices and irrigation management. Characteristics such as experience, training and hired farm labor enhanced paddy yields, while access to agricultural credit was unproductive. Chemical clearing combined with stump removal, tiller ploughing, transplanting and high plant density are the agricultural practices that increased paddy yields, while tiller mudding and basal mineral fertilization were inefficient. In the same way, water distribution by demand, water depth above the soil of less than 5 cm, use of water-saving technologies and farmer's knowledge of how to improve water and fertilizer use-efficiency also helped to boost paddy yields. For sustainable rice production in the context of labor shortages and the financial resources required, future studies will focus on the effectiveness of motorized mudding and agricultural credits for rice farmers. Furthermore, considering the crucial role of training in the adopting of good agricultural and irrigation practices, future research will study strategies for wide diffusion of knowledge to rice producers.

This research delves into the water hammer occurrences, in the transmission pipeline of the SMD (Manda Daba) Multi Village Water Supply Schemes in Afar, Ethiopia. It utilizes simulation software, Bentley HAMMER version 8i to assess transient flow issues and the effectiveness of protective measures. The study pinpoints high risk areas in Scenario 1 marked by pressure spikes, negative pressures and frequent cavitation highlighting the importance of efforts. Prior to safeguards significant pressures reaching 288.27 m H₂O and minimum pressures dropping as low as 9.98 m H₂O are observed. In Scenario 2 where protective measures are implemented notable enhancements are seen with pressures ranging from 121.38 m H₂O to 150.49 m H₂O improved safety levels and substantial reductions in minimum pressures at pump stations. Moreover the study delves into Scenario 3 which explores pipe materials and diameters to provide insights, for pipeline design standards. It emphasizes how protective measures effectively mitigate water hammer effects while also highlighting cost saving potential by incorporating 2000 liter hydro tanks at pump stations. This integration leads to decreased pipeline collapses and maintenance expenses underscoring the significance of addressing challenges pinpointing failure causes and offering solutions to enhance system performance and strengthen reliability within the SMD water supply system

This study employs the reflection symmetry decomposition (RSD) method to extract polarization scattering features from ground object images, aiming to determine the optimal data input scheme for deep learning networks in polarimetric synthetic aperture radar classification. Eight distinct polarizing feature combinations are designed, and the classification accuracy of various approaches is evaluated using the classic convolutional neural networks(CNNs) AlexNet and VGG16. The findings reveal that the commonly employed 6-parameter input scheme, favored by many researchers, lacks the comprehensive utilization of polarization information and warrants attention. Intriguingly, leveraging the complete 9-parameter input scheme based on the polarization coherence matrix results in improved classification accuracy. Furthermore, the input scheme incorporating all 21 parameters from the RSD and polarization coherence matrix notably enhances overall accuracy and the Kappa coefficient compared to the other 7 schemes. This comprehensive approach maximizes the utilization of polarization scattering information from ground objects, emerging as the most effective CNN input data scheme in this study. Additionally, the classification performance using the second and third component total power values (P2 and P3) from the RSD surpasses the approach utilizing surface scattering power value (PS) and secondary scattering power value (PD) from the same decomposition.

Introduction: Chronic wounds caused by diabetes or lower-extremity artery disease are intractable because the wound healing mechanism is no longer effective due to the poor environment of the wound bed. Biosheet obtained using in-body tissue architecture (iBTA) is a collagen-based membranous tissue that is created within the body and autologously contains various growth factors and somatic stem cells including pluripotent stem cells. When applied to a wound, granulation formation can be promoted and even epithelialization may be achieved. Hearin, we report our clinical treatment experience with seven cases of intractable diabetic foot ulcers. Cases: From 46- to 93-year-old 7 patients had large foot ulcers including heel area, which was failed to heal with standard wound treatment. Methods: Two or four Biosheet-forming molds were implanted subcutaneously in the chest or abdomen, and after 3 to 6 weeks, the molds were removed. Biosheets that formed inside the mold were obtained and applied directly to the wound surface. Results: In all cases, there were no problems with the mold embedding and removal procedures, and Biosheets were formed without any infection or inflammation during the implantation period. The Biosheets were simply applied to the wounds, and in all cases, they adhered within one week, did not fall of, and became integrated with the wound surface Complete wound closure was achieved within 8 weeks in two cases and within 5 months in two cases. One patient was lost due to infective endocarditis from septic colitis. One case required lower leg amputation due to the wound recurrence, and one case achieved wound reduction and wound healing in approximately 9 months. Conclusion: Biotube obtained via iBTA promoted wound healing and were extremely useful for intractable diabetic foot ulcers involving heel area.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Extracellular vesicles (EVs) are natural carriers of biomolecules that play a crucial role in cell-to-cell communication and tissue homeostasis under normal and pathological conditions, including inflammatory diseases and cancer. Since the discovery of the pro-regenerative and immune-modulating properties of EVs, EV-based therapeutics have entered clinical trials for conditions such as myocardial infarction and autoimmune diseases, among others. Due to their unique advantages—such as superior bioavailability, substantial packaging capacity, and the ability to traverse biological barriers—EVs are regarded as a promising platform for targeted drug delivery. However, achieving sufficient accumulation of therapeutic agents at the target site necessitates a larger quantity of EVs per dose compared to using EVs as standalone drugs. This challenge can be addressed by administering larger doses of EVs, increasing the drug dosage per administration, or enhancing the selective accumulation of EVs at target cells. In this review, we will discuss methods to improve the isolation and purification of EVs, approaches to enhance cargo packaging—including proteins, RNAs, and small-molecule drugs—and technologies for displaying targeting ligands on the surface of EVs to facilitate improved targeting. Ultimately, this guide can be applied to the development of novel classes of EV-based therapeutics and to overcoming existing technological challenges.

We consider Pisot family substitution tilings in $\R^d$ whose dynamical spectrum is pure point. There are two cut-and-project schemes(CPS) which arise naturally: one from the Pisot family property and the other from the pure point spectrum respectively. The first CPS has an internal space $\R^m$ for some integer $m \in \N$ defined from the Pisot family property, and the second CPS has an internal space $H$ which is an abstract space defined from the property of the pure point spectrum. However it is not known how these two CPS's are related. Here we provide a sufficient condition to make a connection between the two CPS's. In the case of Pisot unimodular substitution tiling in $\R$, the two CPS's turn out to be same due to [5, Remark 18.5].

A stable match, an intercuspated maxilla-mandible relation is the universally accepted goal for dental restorative interventions, yet the underlying sensorimotor mechanisms to achieve this goal in the natural jaw closure remains to be elucidated. Dentists have intuitively regarded peripheral sensory innervation from tooth contacts as a significant control element for jaw muscle actions, both in the state of health and in cases of pathological dysfunction. However, therapeutical interventions for reshaping the dental arch anatomy and jaw relations have not always been successful. Repetitive masticatory chewing cycles, swallowing, talking, as well as volitional jaw-opening and -closing involve stereotyped neural commands from the central nervous system that are modulated in reaction to the sensory afferent feedback from the peripheral neurons and their sensor organs. The aim of this article is to describe, on a fraction of a second time-scale, the minuscule tilts and kinematic events of mandible during the making of a stable match with maxilla. Evidence of the importance of tooth contacts as the sensorimotor motivation of each of the successive kinematic steps of the “mandible-meets-maxilla-narrative” are discussed.

Microbiomes, comprised of diverse microbial species and viruses, play pivotal roles in human health, environmental processes, and biotechnological applications and interact with themselves, their environment, and hosts via metabolites and signaling molecules. Our understanding of microbiomes is still limited and hampered by their complexity. A concept improving this understanding is systems biology, which focuses on the holistic description of biological systems utilizing experimental and computational methods. An important set of such experimental methods are metaomics methods which analyze microbiomes and output lists of molecular features. These lists of data are integrated, interpreted, and compiled into computational microbiome models, to predict, optimize, and control microbiome behavior. There exists a gap in understanding between microbiologists and modelers/bioinformaticians, stemming from a lack of interdisciplinary knowledge. This knowledge gap hinders the establishment of computational models in microbiome analysis. This review aims to bridge this gap and is tailored for microbiologists, researchers new to microbiome modeling, and bioinformaticians. To achieve this goal, it provides an interdisciplinary overview of microbiome modeling, starting with fundamental knowledge of microbiomes, metagenomics methods, and modeling formalisms. Furthermore, the review explains model building, examples of microbiome model applications for prediction, optimization, and control. It concludes with guidelines, software, and repositories for modeling. Each section provides entry-level information, serving as a valuable resource for comprehending and navigating the complex landscape of microbiome research and modeling.

A theory is presented about the information available for guiding purposeful actions by any organism, whether animal or plant, and about how the information is used in guiding actions.

Electronic health records (EHRs) are becoming a vital source of data for healthcare quality improvement, research, and operations. However, much of the most valuable information contained in EHRs remains buried in unstructured text. The field of clinical text mining has advanced rapidly in recent years, transitioning from rule-based approaches to machine learning and, more recently, deep learning. With new methods come new challenges, however, especially for those new to the field. This review provides an overview of clinical text mining for those who are encountering it for the first time (e.g. physician researchers, operational analytics teams, machine learning scientists from other domains). While not a comprehensive survey, it describes the state of the art, with a particular focus on new tasks and methods developed over the past few years. It also identifies key barriers between these remarkable technical advances and the practical realities of implementation at health systems and in industry.

Preschoolers with disabilities and their caregivers have been neglected in health and social service provision in most low-income countries and arguably too in low resourced areas of more affluent nations. Yet as this rapid review of published literature identifies, there are low-cost, evidence-based strategies to address their needs that can be implemented in communities by local people. Five key features of the necessary supports are examined. First the leadership functions required to create and implement the support services. Second, the family-centred, home-based support provided to caregivers and the personnel undertaking this form of support. Third, providing opportunities for peer support to flourish and encouraging the formation of advocacy groups across families. Fourth, mobilizing the support of significant groups within the community; notably traditional healers and leaders; health services and poverty alleviation initiatives. Fifth, devising ways in which preschool educational opportunities can be offered to children as a prelude to their inclusion in primary schools. The review serves a further purpose. It provides an example of how public health researchers and academics could achieve more rapid implementation of evidence-based knowledge into existing and new support services through dissemination to community practitioners.

In recent times, there has been a growing interest in the use of control charts as a feedback process monitoring technique. Particularly, CUSUM schemes have been proven to be efficient for monitoring processes where the magnitude of the sustained mean shifts is small or moderate. However, because of the constant control limits, the detection ability of CUSUM schemes becomes slow at the initial set-up of the process. The fast initial response FIR feature has often been used to enhance it at the process startup. Meanwhile, the dynamism of real-life problems has always encouraged a more sensitive CUSUM scheme capable of detecting process shifts more rapidly. In this paper, an improved CUSUM scheme for monitoring process mean is proposed. This scheme will be substantial for monitoring processes whose observations are obtained at a distant time interval for example hourly, daily or weekly and where the sustained shifts are assumed to be small or moderate. To demonstrate the practical applications of the proposed scheme, we present its real-life application using datasets from a bottling company and petroleum refinery laboratory.

We give three new authentication schemes without secrecy. The first two on finite fields and Galois rings, using Gray map for this link. The third construction is given on Galois rings. The main achievement in this work is to obtain optimal impersonation and substitution probabilities in the schemes. Additionally, in the first and second scheme, we simplify the source space and bring a better relationship between the size of the message space and the key space than the given in [8]. Finally, we provide a third scheme on Galois rings, which generalizes the scheme over finite fields constructed in [9].

This article analyzes the emergence of partnerships between corporations and nongovernmental organizations (NGOs) through voluntary product labeling schemes. The economics, management, and business literatures are reviewed to highlight cross-checking, consistencies, and complementarities among these disciplines. The objective is to identify and analyze the motives, risks, and joint benefits of partnering via voluntary product labeling, using examples from the agri-food sector. This study is an attempt to offer a framework of corporate-NGO partnerships by showing that the drivers and risks of each partner merge because each takes a step into the sphere of the other. The main risks – namely, a loss of profitability, credibility and legitimacy – are related to the financial and existential dependency and the asymmetric information between the partners in favor of corporations, inducing an ``NGO-capture'' risk.

In the global fight against malaria, standard vector control methods such as indoor residual spraying (IRS) and insecticide-treated nets (ITNs) are intended to protect inside residential structures and sleeping spaces. However, these methods can still leave individuals vulnerable to residual transmission from vectors that they may be exposed to outdoors. Nchelenge District in northern Zambia experiences high persistent malaria transmission even with ITNs and IRS in place. However, very few studies have examined outdoor vector activity. To assess diversity and abundance of outdoor foraging female anopheline mosquitoes, CDC light traps were used as proxy measures for mosquito host-seeking, set in three outdoor trapping schemes randomly assigned on different nights: 1) locations where people congregate at night outside of the house within the peri-domestic space, 2) animal pens or shelters, and 3) high human-trafficked areas, such as paths to latrines, where traps were baited with BG-Lure®. 1,087 total female anophelines were collected over a total of 74 trap nights. Anopheles funestus s.s. comprised the majority of the collection (86%), with An. gambiae s.s. (2%) and a highly diverse sampling of other anophelines (12%) making up the remainder. Plasmodium falciparum parasites were only detected in An. funestus (1%). No significant difference in species diversity or female anopheline abundance was detected between trapping schemes. Outdoor foraging anopheline mosquitoes, including a number of infectious An. funestus, may partially explain the difficulty of controlling malaria transmission in Nchelenge District where vector control is only targeted indoors. BG-Lure® shows some promise as an alternative to human-baited landing catch collections in this resource-poor setting.

In this paper, we examine two strategies for boosting the performance of ensembles of Siamese networks (SNNs) for image classification using two loss functions (Triplet and Binary Cross Entropy) and two methods for building the dissimilarity spaces (FULLY and DEEPER). With FULLY, the distance between a pattern and a prototype is calculated by comparing two images using the fully connected layer of the Siamese network. With DEEPER, each pattern is described using a deeper layer combined with dimensionality reduction. The basic design of the SNNs takes advantage of supervised k-means clustering for building the dissimilarity spaces that train a set of support vector machines, which are then combined by sum rule for a final decision. The robustness and versatility of this approach are demonstrated on several cross-domain image data sets, including a portrait data set, two bioimage and two animal vocalization data sets. Results show that the strategies employed in this work to increase the performance of dissimilarity image classification using SNN is closing the gap with standalone CNNs. Moreover, when our best system is combined with an ensemble of CNNs, the resulting performance is superior to an ensemble of CNNs, demonstrating that our new strategy is extracting additional information.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

This paper introduces a groundbreaking approach to enriching the museum experience using GPT4, a state-of-the-art language model by OpenAI. By developing a museum guide powered by GPT4, we aim to address the challenges visitors face in navigating vast collections of artifacts and interpreting their significance. Leveraging the model’s natural language understanding and generation capabilities, our guide offers personalized, informative, and engaging experiences. However, caution must be exercised as the generated information may lack scientific integrity and accuracy. To mitigate this, we propose incorporating human oversight and validation mechanisms. The subsequent sections present our own case study, detailing the design, architecture, and experimental evaluation of the museum guide system, highlighting its practical implementation and insights into the benefits and limitations of employing GPT4 in the cultural heritage context.

Microbial symbioses exhibit astounding adaptations, yet all symbionts face the problem of how to reliably associate with host offspring every generation. A common strategy is vertical transmission, in which symbionts are directly transmitted from the female to her offspring. The diversity of symbionts and vertical transmission mechanisms is as expansive as the diversity of eukaryotic host taxa that house them. However, there are several common themes among these mechanisms based on the degree to which symbionts associate with the host germline during transmission. In this review, we detail three distinct vertical transmission strategies, starting with associations that are transmitted from host somatic cells to offspring somatic cells, either due to lacking a germline or avoiding it. A second strategy involves somatically-localized symbionts that migrate into the germline during host development. The third strategy we discuss is one in which the symbiont maintains continuous association with the germline throughout development. Unexpectedly, the vast majority of documented vertically inherited symbionts rely on the second strategy: soma-to-germline migration. Given that not all eukaryotes contain a sequestered germline and instead produce offspring from somatic stem cell lineages, this soma-to-germline migration is discussed in the context of multicellular evolution. Lastly, as recent genomics data have revealed an abundance of horizontal gene transfer events from symbiotic and non-symbiotic bacteria to host genomes, we discuss their impact on eukaryotic host evolution.

A via ferrata (from the German “klettersteig”, hereinafter VF) is a sports route located on forest and mountains vertical rock walls equipped with steps, chains, artificial dams, bridges and other fixed elements and which have a steel cable (safety cable) all the way along allowing users to secure their progress and avoid possible falls [1]. This article aims to analyse the state of the art of the VF sector in Spain, especially in terms of the regulations of obligatory compliance, in addition to defining the basic characteristics of the installations to ensure that these are safe for users, providing a previously non-existent summary of the most important recommendations regardless of the country where they are installed.

Human cytomegalovirus (HCMV) is a β-herpes virus that is a significant pathogen within immune compromised populations. HCMV morbidity is induced through viral dissemination and inflammation. Typically, viral dissemination is thought to follow Fenner’s hypothesis where virus replicates at the site of infection, followed by replication in the draining lymph nodes, and eventually replicating within blood filtering organs. Although CMVs somewhat follow Fenner’s hypothesis, they deviate from it by spreading primarily through innate immune cells as opposed to cell free virus. Also, in vivo CMVs infect new cells via cell to cell spread and disseminate directly to secondary organs through novel mechanisms. We review the historic and recent literature pointing to CMV’s direct dissemination to secondary organs and the genes that it has evolved for increasing its ability to disseminate. We also highlight aspects of CMV infection for studying viral dissemination when using in vivo animal models.

Estimates by the World Health Authority suggest that 1 billion people do not have access to the assistive technologies they require. Over the past decade, the design of products that empower people with a disability has shifted from specialised and dedicated products designed only for those with a disability to features and functions integrated into cost-effective consumer technologies for the benefit of all. The opportunity for expansion of the availability of such technologies is at risk of being ignored as a result of models of delivery that are founded in medical devices and which have failed to reflect trends in our understanding of technology and the choices and preferences expressed by persons with a disability. This research undertaken suggests that the opportunities of such expansion offer significant benefits to people with a disability and better both economic and social return on investment for authorities.

Fossil-based emissions can be avoided through using wood in place of non-renewable raw materials as energy and materials. However, increasing wood harvest influences forest carbon stocks. This effect may reduce the overall climate benefit of wood use significantly but is widely overlooked. We carried out a systematic review of simulation studies and compared differences in forest carbon and amount of wood harvested between more and less intensive wood harvest scenarios for three different time perspectives; short (1-30 years), mid (31-70 years) and long (71-100 years). Out of more than 450 reviewed studies 44 provided adequate data. Our results show that increased harvesting reduced carbon stocks over 100 years in temperate and boreal forests roughly 1.6 (stdev 0.9) t_C per t_C harvested. The value proved to be robust when outliers explicitly influenced by other factors than change in harvest rate, such as increase in fertilization or forest area, were removed. Interestingly, no significant difference in carbon impacts was found for average values of boreal and temperate forests or between short and long time-horizons. However, impacts tend to be greatest in the mid-term. This carbon balance indicator that we estimated can be interpreted as carbon debit of wood harvest in forests. It is significant compared with the typical GHG credits in technosphere generated by avoiding fossil emissions in substitution and increase in carbon storage in harvested wood products, and should not be ignored. Our estimates provide default values that can directly be included in GHG balances of products or assessment of mitigation policies and measures related to wood use. However, more systematic scenarios and transparent data in which different factors influencing forest carbon stocks are separately studied are clearly required to provide better constrained estimates for specific forest types.

Horizontal transfer of transposons (HTT) is an important source of genomic evolution in eukaryotes. The HTT dynamics is well characterized in eukaryotes including insects however, but there is a huge gap of knowledge about HTT regarding many eukaryotes’ species. In this study we analyzed the events of the HTT between Rhus gall aphids (Hemiptera) and other insects. We analyzed the Mariner-like transposable elements (MLEs) belongs to Rhus gall aphids for the possible HT events. The MLEs have patchy distribution and have high similarity over the entire length of element with insects MLEs from different orders. We selected representative sequences from the Rhus gall MLEs and identified five events of HT between MLEs of Rhus gall aphids and other insects from five different orders. We also found multiple HTT events among the MLEs of insects from the five orders which demonstrate that these Mariner elements have been involved in recurrent HT between these six order of insects. Our current study closed the knowledge gap of HTT and reported the events between Rhus gall aphids and other insects for the first time. We believe that this study about HTT events will help to understand the evolution and spread of transposable elements in the genomes of Rhus gall aphids.

The ability to replicate scientific experiments is a cornerstone of the scientific method. Sharing ideas, workflows, data, and protocols facilitates testing the generalizability of results, increases the speed that science progresses, and enhances quality control of published work. Fields of science such as medicine, the social sciences, and the physical sciences have embraced practices designed to increase replicability. Granting agencies, for example, may require data management plans and journals may require data and code availability statements along with the deposition of data and code in publicly available repositories. While many tools commonly used in replicable workflows such as distributed version control systems (e.g. “git”) or scripted programming languages for data cleaning and analysis may have a steep learning curve, their adoption can increase individual efficiency and facilitate collaborations both within entomology and across disciplines. The open science movement is developing within the discipline of entomology, but practitioners of these concepts or those desiring to work more collaboratively across disciplines may be unsure where or how to embrace these initiatives. This article is meant to introduce some of the tools entomologists can incorporate into their workflows to increase the replicability and openness of their work. We describe these tools and others, recommend additional resources for learning more about these tools, and discuss the benefits to both individuals and the scientific community and potential drawbacks associated with implementing a replicable workflow.

Simple Summary (148 words) There is increasing evidence, that cannabinoids may play an important and dual role in tumour therapy. On one hand, they are cytotoxic against cancer cells with a low toxicity against normal, healthy tissues, and on the other, they may reduce typical side effects of chemotherapy. Publications on the main motive for use of cannabis (cannabinoids) by cancer patients show that patients' expectations exceed scientific facts. This article briefly describes results of combinations of cannabinoids with standard antineoplastic drugs on tumours and on side effects of tumour therapy. Although observations are still limited to animal studies with very few experiences in patients, preliminary data suggest that adjuvant cannabinoids may improve the survival of glioblastoma and perhaps of patients with other tumours. Benefits have also been reported about chemotherapy-induced nausea and vomiting, chemotherapy-induced peripheral neuropathic pain, loss of appetite and anxiety. Although results are promising, much more research is necessary. Abstract (192 words) Cancer, one of the leading causes of death worldwide, is on the rise. The high toxicity of conventional chemotherapy, often applied as drug cocktails, and resistance development limits the use of anti-neoplastic drugs and reduces the quality of life. With an easier access, a growing number of patients are using cannabis (cannabinoids) for alleviation of their symptoms, and in the hope of improving survival. This narrative article summarizes results observed with combinations of phytocannabinoids and standard chemotherapeutic agents in animal tumour models and in patients. Preliminary data suggest that standard antineoplastic agents combined with cannabinoids exert increased anti-cancer actions, reduce resistance development and improve survival. Respective experiences in patients are still scarce and concern small numbers with glioblastoma, and pancreatic carcinoma. Further benefits of combinations with cannabinoids have also been reported for chemotherapy-induced nausea and vomiting, loss of appetite (dronabinol), chemotherapy-induced peripheral neuropathic pain and anxiety (cannabidiol). In addition, phytocannabinoids, in particular cannabidiol, may play a role in the protection of organs such as heart, lung or kidney against chemotherapy-induced toxicity. Although results are promising, much more research is needed to determine whether positive experiences of adjuvant cannabinoids outweigh eventual risks.

The objective of this study is to preliminarily evaluate a new CT-biopsy guidance device, an origami needle guide. The device is created by laser cutting the structure from a sheet of cardboard, 3D printing two radiocontrast agent grids on to the surface and folding the structure into a rectangular prism with a viewing window. An abdominal imaging phantom was used to evaluate the device through CT imaging and the targeting of lesions for needle insertion. The lesion targeting trials resulted in a mean targeting error of 1.88 mm with a standard deviation of 0.73 mm. The device attaches to the patient and is rigid enough to adequately support standard biopsy needles, reducing the effect of gravity and the risk of laceration by the needles, making it potentially advantageous for biopsy of superficial lesions and lesions approached from a horizontal orientation. The device supports insertion of multiple needles at once, making it particularly suitable for composite ablation using multiple needles. Another advantage of the device is that it can guide off-axial needle insertion. The low-cost and disposability of the device make it well-suited for the minimally invasive image guided therapy environment.

Human epidermal growth factor receptor 2 (HER2) is a major prognostic and predictive marker overexpressed in 15- 20 % of breast cancers. The diagnostic reference standard for selecting patients for HER2-targeted therapy is by analysis of tumor biopsies for HER2 expression and amplification. Previously patients were either defined as HER2-positive or negative, however, with approval of novel treatment options, specifically the antibody-drug conjugate trastuzumab deruxtecan, many breast cancer patients with tumors expressing low levels of HER2 and lacking HER2 amplification have become eligible for HER2-targeted therapy. Such patients will need to be reliably identified by suitable diagnostic methods. Biopsy-based diagnostics are invasive, and repeat biopsies are not always feasible. They cannot visualize heterogeneity of HER2 expression, leading to a substantial number of misdiagnosed patients. An alternative and highly accurate diagnostic method is mo-lecular imaging with radiotracers. In case of HER2, various studies demonstrate the clinical utility and feasibility of such approaches. Affibody-based radiotracers are clinically validated molecules with favorable characteristics for imaging. In this article we summarize the HER2-targeted therapeutic landscape, describe the experience with imaging diagnostics for HER2, and review the currently available clinical data on HER2-Affibody-based molecular imaging as novel diagnostic tool in breast cancer and beyond.

This study introduces a hardware accelerator to support various Post-Quantum Cryptosystem (PQC) schemes, addressing the quantum computing threat to cryptographic security. PQCs, while more secure, also bring significant computational demands, especially problematic for lightweight devices. Previous hardware accelerators are typically scheme-specific, which is inefficient given the National Institute of Standards and Technology (NIST)'s multiple finalists. Our approach focuses on the shared operations among these schemes, allowing a single design to accelerate multiple candidate PQCs at the same time. This is further enhanced by allocating resources according to performance profiling results. Our compact, scalable hardware accelerator supports four of NIST PQC finalists, achieving an area efficiency of up to 81.85\% compared to the current state-of-the-art multi-scheme accelerator while supporting twice as many schemes. The design demonstrates average throughput improvements ranging from 0.97$\times$ to 35.97$\times$ across the four schemes and their main operations, offering an efficient solution for implementing multiple PQC schemes within constrained hardware environments.

Good Boussinesq equations will be considered in this work. First we apply three combined compact schemes to approximate spatial derivatives of good Boussinesq equations. Then three fully discrete schemes are developed based on symplectic scheme in time direction, which are sympletic-structure preserving.Meanwhile, the convergence and conservation of the fully discrete schemes are analyzed. Finally, we present numerical experiments to confirm our theoretical analysis. Both our analysis and numerical test indicate that the fully discrete schemes are efficient in solving the spatial derivative mixed equation.

Fifth Generation (5G) communication technology is intended to offer higher data rates, outstanding user exposure, power consumption, and extremely short latency. Such cellular networks will implement a diverse multi-layer model comprising of device-to-device networks, macro-cells, and dissimilar categories of small-cells to assist customers with desired quality-of-service (QoS). This multi-layer model affects several studies that confront utilizing interference management and resource allocation in 5G networks. With the growing need and the lack of resources, the resource distribution problem desires to be focused capably to accomplish the traffic and to enhance network working. One of the utmost serious problems is to alleviate the jamming from the network in support of having a better QoS. However, there are limited review papers written on resource distribution, there is no particularize and organized review carry out in 5G resource allocation. Hence, this article covers and evaluates the argument using a classification of existing developing resource allocation schemes in 5G thoroughly by classifying the schemes to enhance the service quality. This survey comprises the discussion based on metrics used to evaluate the performance. It would also permit ahead beyond evidence on resource allocation methods in 5G and empowers the scholars to meet the present research areas to focus on.

The incorporation of renewable energy into power systems poses serious challenges to the transmission and distribution power system operators (TSOs and DSOs). To fully leverage these resources there is a need for a new market design with improved coordination between TSOs and DSOs. In this paper we propose two coordination schemes between TSOs and DSOs: one centralised and another decentralised that facilitate the integration of distributed based generation; minimise operational cost; relieve congestion; and promote a sustainable system. To this end, we approximate the power equations with linearised equations so that the resulting optimal power flows (OPFs) in both the TSO and DSO become convex optimisation problems. In the resulting decentralised scheme, the TSO and DSO collaborate to optimally allocate all resources in the system. In particular, we propose an iterative bi-level optimisation technique where the upper level is the TSO that solves its own OPF and determines the locational marginal prices at substations. We demonstrate numerically that the algorithm converges to a near optimal solution. We study the interaction of TSOs and DSOs and the existence of any conflicting objectives with the centralised scheme. More specifically, we approximate the Pareto front of the multi-objective optimal power flow problem where the entire system, i.e., transmission and distribution systems, is modelled. The proposed ideas are illustrated through a five bus transmission system connected with distribution systems, represented by the IEEE 33 and 69 bus feeders.

Understanding the subtle signs of carpal instability and other unique injury patterns in the wrist is a critical skill for radiologists. Proper patient management and outcomes are directly dependent on the accurate interpretation of wrist imaging studies. This review will provide a detailed overview of typical imaging features of carpal trauma and instability, management, and complications, using multimodality imaging and original medical illustrations. A detailed overview of the osseous, ligamentous, arterial anatomy of the wrist, arcs of Gilula, and zones of vulnerability will be provided. Carpal fractures, dislocations, special radiographic views, and imaging pearls will be discussed. Instability patterns and the myriad of associate abbreviations (CID, CIND, CIC, CIA, VISI, DISI, SLD, LTD, MCI, SLAC, SNAC) will be clarified. Expected outcomes, potential complications, and management will be reviewed.

A degree in physiology in Nigeria offers a enormous opportunities that many undergraduates may be unaware of.This article explores different career paths available to physiology undergraduate and graduates in Nigeria. It outlines various fields within clinical and healthcare settings, research and academia, biotechnology and pharmaceuticals, and even alternative careers. It also details specific specializations within clinical physiology, including cardiovascular, respiratory, neurophysiology, sleep, gastrointestinal, and renal physiology.The article emphasizes the importance of gaining practical experience through internships, volunteer work, and networking to equip physiology them with essential skills for job market.

The way flipped classrooms are perceived and even practised by teachers is sometimes approximative. For example, while the Covid-19 pandemic has pushed many universities to adopt distance learning, flipped classrooms have often been mentioned as a solution in that context. This inducement maintains a confusion between flipped classrooms and distance learning that might be detrimental for both students and teachers. Moreover, embarking on a new pedagogical practice such as flipped classroom could be intimidating and time-consuming. For these reasons, this article aims to share some tips for implementing a flipped classroom, with examples from biology and biochemistry. Based on our own experiences but also on the current scientific literature, we propose to structure the advises around three phases: Preparation, Implementation, and Follow-up. In the preparation phase it is advised to not only plan to invert time but also say it, as well as to identify (or create) resources for learning in autonomy. In the Implementation phase it is suggested to i) Be explicit in the acquisition of knowledge, and foster students' autonomy; ii) Explore active learning in class; iii) Develop skills of cooperation and sharing; and iv) Differentiate. In the follow-up phase it is proposed to i) Evaluate; ii) Take care of the logistics and your posture; iii) Document your flipped classroom and iv) Share.

The maker movement has reached the optics labs, empowering researchers to actively create and modify microscope designs and imaging accessories. 3D printing has especially had a disruptive impact on the field, as it entails an accessible new approach in fabrication technologies, namely additive manufacturing, making prototyping in the lab available at low cost. Examples of this trend are taking advantage of the easy availability of 3D printing technology. For example, inexpensive microscopes for education have been designed, such as the FlyPi. Also, the highly complex robotic microscope OpenFlexure represents a clear desire for the democratisation of this technology. 3D printing facilitates new and powerful approaches to science and promotes collaboration between researchers, as 3D designs are easily shared. This holds the unique possibility to extend the open-access concept from knowledge to technology, allowing researchers from everywhere to use and extend model structures. Here we present a review of additive manufacturing applications in microscopy, guiding the user through this new and exciting technology and providing a starting point to anyone willing to employ this versatile and powerful new tool.

The security of several full homomorphic encryption (FHE) schemes depends on the hardness of the approximate common divisor (ACD) problem. The analysis of attack and defense against the system is one of the frontiers of cryptography research. In this paper, the performance of existing algorithms, including orthogonal lattice, simultaneous diophantine approximation, multivariate polynomial and sample pre-processing are reviewed and analyzed for solving the ACD problem. Orthogonal lattice (OL) algorithms are divided into two categories (OL-$\land$ and OL-$\vee$) for the first time. And an improved algorithm of OL-$\vee$ is presented to solve the GACD problem. This new algorithm works well in polynomial time if the parameter satisfies certain conditions. Compared with Ding and Tao's OL algorithm, the lattice reduction algorithm is used only once, and when the error vector $\mathbf{r}$ is recovered in Ding et al.'s OL algorithm, the possible difference between the restored and the true value of $p$ is given. It is helpful to expand the scope of OL attacks.

Manual interpretation of these huge amounts of image volumes are susceptible to inter-reader variability and human error. Thus, accurate automated CAD scheme is highly desirable in clinical pathological diagnosis. In this research, plethora of machine learning paradigms (e.g. feature extraction, dimensionality reduction and supervised classification methods) were explored, evaluated, compared and analyzed to identify the optimal pathway for brain MR images (normal vs neoplastic) binary classification task. External validation dataset was used to test the generalizability of the optimal predictive models implemented. Relevant and informative features were selected to construct cross-validated decision tree and eventually simple rule set was built based on the decision tree. The experimental results show that almost all pattern recognition paradigms achieve high accuracy with careful selection of number of attributes. LDA+ELM with 55 features are the optimal pipelines which achieve perfect classification when training and test data are of same source; and achieving (accuracy=97.5%, AUC=0.989, sensitivity=95% and specificity=100%) under balanced test dataset; (accuracy=99.5%, AUC=0.988, sensitivity=95% and specificity=100%). Cross-validated decision tree model also shows comparable performance: accuracy=98.8%, AUC=99.1%, sensitivity=99.6% and specificity=98.2%. Three highly relevant and robust attributes are visualized and selected for construction of decision tree models and finally a rule sets are read directly off the decision tree. This rule sets can potentially serve as fast and accurate classification algorithm.

In response to the escalating global waste production rate, sustainable waste management be-comes indispensable. In parallel, the transformation of energy system is vital in order to ensure affordable, decentralized, and sustainable energy for the global community, based on economic, environmental, and social criteria. Waste-to-Energy (WtE) is an effective option in order to put a stepping stone to address both issues provided that multiple views and criteria are considered. This paper puts forward a generic methodological framework to holistically assess WtE technologies based on the PROMETHEE approach. In addition to environmental, economic, and social aspects, demonstration of applicability of the proposed methodology is realized at national level the case of Greece. Anaerobic Digestion seems to be the most preferable choice, recognized for its cost-effectiveness and lower environmental burden to other WtE technologies (i.e. gasification, pyrolysis, incineration). Insightful expert opinions and public preference are of paramount importance to the adopted approach, revealing technology-specific concerns and preferences. In addition, the material presented underscores a crucial gap in Life Cycle Assessment studies for large-scale WtE, emphasizing the need for future scientific attention and exploration. Public consensus indicates a positive overall attitude towards waste valorization in the context of energy production.

Access to broadband communications in different parts of the world has become a priority for some governments and regulatory authorities around the world in recent years. Building new digital roads and pursuing a connected society includes looking for easier access to the Internet. In general, not all the areas where people congregate are fully covered, especially in rural zones, thus restricting access to data communications and bringing inequality. In the present review article, we have comprehensively surveyed the use of three platforms to deliver broadband services to such remote and low-income areas are proposed: Unmanned Aerial Vehicles (UAV), Altitude Platforms (APS), and Low-Earth Orbit (LEO) satellites. These novel strategies support the connected and accessible world hypothesis. Hence UAVs are considered a noteworthy solution since their efficient maneuverability can aboard the rural coverage issues or not-spots.

Conditional Privacy Preserving Authentication (CPPA) schemes are an effective way of securing communications in Vehicular Adhoc Networks (VANETs), as well as ensuring user privacy and accountability. Cryptanalysis plays a crucial role in pointing out the vulnerabilities in existing schemes to enable the development of more resilient ones. In 2019, Zhang proposed a CPPA scheme for VANET security (PA-CRT), based on identity batch verification (IBV) and Chinese remainder theorem (CRT). In 2023, this scheme was crypt-analyzed by Tao. In this paper we provide our own crypt analysis of Zhang’s scheme and propose counter measures to mitigate Tao’s attacks. Furthermore, in 2021, Xiong proposed a Certificateless Aggregate Signature (CLAS) scheme which was cryptanalyzed by Shim in 2023. Xiong subsequently proposed a modified CLAS scheme which is also cryptanalyzed in this paper.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

Product counterfeiting is an on-going problem in supply chains and retail environments, Recently an anti-counterfeiting protocol to address this issue via cost-effective use of auto-identification technologies such as radio-frequency identification (RFID) was proposed by researchers.Yet the use case of re-selling the same product was not been fully addressed which might cause serious problem for the exciting and proposed schemes and transactions. This paper proposes an extended RFID-based anti-counterfeiting to address the use case of the original buyer reselling the same item to a second buyer. The extended scheme will be followed by a formal security analysis to show that the proposed protocol satisfies the requirements of security correctness and is resistant to compromise through security attacks.

Pharmaceutical packaging is very crucial in as much as it plays the role of enhancing the stability, efficacy as well as safety of the produced medicine through the material used in packaging. It is important to note that cGMP Chapters 661 and 671 are focused on explaining how one should assess the quality of container materials in the sphere of pharmaceuticals. These chapters encompass a number ofmatters among them being Plastic and glass containers and performance testing; they serve as a resource that aids in assuring all standards are met with profound proficiency. Following this, the performance of two core chapters of USP known as Chapter 661 on “Containers—Glass” and Chapter 671 on “Containers—Performance Testing” will be dealt with in a step-by-step manner in the following paper while providing a comprehensive review of both at the same time. Understanding and legal obedience to these rules, as stipulated in the above-mentioned chapter, are indispensable for almost all the parties involved in the production of the drugs, together with the policies and legislation on the same. Thus, the purpose of this paper is to describe and discuss the major aspects of the understanding, application, requirements and evaluation procedures depending on the USP Chapters 661 and 671 in the sphere of the pharmaceutical market.

The more than thirty spacetime theorems developed over the past five decades establish that the universe and its spacetime dimensions have emerged from a cause/Causal Agent beyond the cosmos. Thus, to infer that this cause/Causal Agent may have intervened in the origin and history of Earth and Earth’s life resides well within the bounds of reason. Meanwhile, proponents of each of the three prevailing naturalistic models for the origin and history of Earth’s life have marshalled arguments and evidence that effectively undermine and refute the other two models. A biblical perspective and approach to Earth’s life can help resolve this impasse. While a superficial and pervasive appeal to divine intervention thwarts scientific advance, so does a rigid adherence to naturalism. A productive way forward is to identify which models (or parts of models), whether naturalistic, theistic, or a combination, most effectively narrow, rather than widen, knowledge gaps, minimize anomalies, offer the most comprehensive and detailed explanation of the data, and prove most successful in predicting scientific discoveries.

Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

Botswana, Eswatini and Lesotho are three Southern African countries which make use of re-turn-of-service (RoS) schemes to increase human resources for health in their countries. These initiatives bind beneficiaries to a pre-defined period of service upon completion of their studies based on the length of funding support received. We aim to review the history of these policies to understand the conceptualisation, intent and implementation of these schemes. We used a mul-ti-methods research design which consisted of a literature review, policy review and semi-structured interviews with policymakers and implementors. All three governments have a combination of grant-loan schemes and full bursaries or scholarships. The policies have all been operating for over 20-years, with Eswatini’s pre-service being the oldest since it was introduced in 1977 followed by Lesotho’s 1978 policy and Botswana’s 1995 pre-service policy. These policies have never been reviewed or updated. RoS schemes in these countries were introduced to ad-dress critical skills shortages, improve employability prospects for citizens, to have competent public sector employees by global standards, and to aid career progress of government employ-ees. Ministries of Health are passive role players. However, these schemes can only be efficient if there is clear cooperation and coordination between all stakeholders.

A system of wavelet collocation upwind schemes is constructed for solving hyperbolic conserva-tion laws based on a class of interpolation wavelets. The bias magnitude and symmetry factor are defined to depict the asymmetry of the adopted scaling basis function in wavelet theory. Effects of characteristics of the scaling functions on the schemes are explored based on numerical tests and Fourier analysis. The numerical results reveal that the stability of the constructed scheme is af-fected by the smoothness order, N, and the asymmetry of the scaling function. The dissipation analysis suggests that schemes with Neven have negative dissipation coefficients, leading to unstable behaviors. Only scaling functions with Nodd and bias magnitude of 1 can be used to construct stable upwind schemes due to the non-negative dissipation coefficients. Resolution of the wavelet scheme tends to the spectral resolution as the order of accuracy of the scheme in-creases.

Metabolites are at the end of the gene-transcript-protein-metabolism cascade. As such, metabo-lomics is the omic approach that offers the most direct correlation with phenotype. This allows that, where genomics, transcriptomics and proteomics fail to explain a trait, metabolomics might give an answer. Complex phenotypes, which are determined by the influence of multiple small effect alleles, are an example of these situations. Consequently, the interest in metabolomics has increased ex-ponentially in the last years. As a newer discipline, the metabolomics bioinformatics analysis pipe-lines are not as standardized as in the other omic approaches. In this review we synthesized the different steps that need to be carried out to obtain biological insight from the annotated metabolite abundance raw data. These steps were grouped in three different modules: preprocessing, statistical analyses and metabolic pathway enrichment. We included within each one of them the different state-of-the art procedures and tools that can be used depending on the characteristics of the study, providing details about the characteristics of each method has, as well as the issues the reader might encounter. Finally, we introduce genome scale metabolic modeling as a tool for obtaining pseu-do-metabolomic data in situations where its acquisition is difficult, being possible to analyze the resulting data with the modules of the described workflow.

Background: Endoscopic Ultrasound (EUS) is widely used for the diagnosis of bilio-pancreatic and gastrointestinal (GI) tract diseases, for the evaluation of subepithelial lesions, and for sampling of lymph nodes and solid masses lo-cated next to the GI tract. The role of Artificial Intelligence in healthcare in growing. This review aimed to provide an overview of the current state of AI in EUS from imaging to pathological diagnosis and training. Methods: AI algorithms can assist in lesion detection and characterization in EUS by analysing EUS images and identifying suspicious areas that may require further clinical evaluation or biopsy sampling. Deep learning tech-niques, such as convolutional neural networks (CNNs), have shown great potential for tumour identification and subepithelial lesion (SEL) evaluation by extracting important features from EUS images and using them to classify or segment the images. Results: AI models with new features can increase the accuracy of diagnoses, provide faster diagnoses, identify subtle differences in disease presentation that may be missed by human eyes, and provide more information and in-sights into disease pathology. Conclusions: The integration of AI in EUS images and biopsies has the potential to improve the diagnostic accura-cy, leading to better patient outcomes and to a reduction of repeated procedures in case of non-diagnostic biopsies.

The aim of this study is to analyse the names given to streets, monuments, spots of interest, et cetera in a street guide of an imaginary city called The Manada, whose map is constructed as a painting. For this analysis, we start from the 257 entries of the Street Guide, select their possible antecedents in literature and contextualize this street guide with respect to these antecedents. Our methodology is focused on two specific aspects of the Street guide: (1) to detect the semantic fields that emerge (with a methodology inverse to the creative one, that is, asking ourselves what key questions would result in the names of the streets) and (2) to detect the literary devices that are put into practice in the names of the places on the map, in order to determine how the relationship with the viewer-reader is established from a connotative level. The main findings of this study demonstrate that this is a unique piece, a new format both pictorial and literary, and that it has transcendence in the theme it deals with: the concealment of systemic violence. Comments about feminism, apotropaic devices and surrealism end our text.

From single-cell organisms to complex neural networks, all evolved to provide control solutions to generate context and goal-specific actions. Neural circuits performing sensorimotor computation to drive navigation employ inhibitory control as a gating mechanism, as they hierarchically transform (multi)sensory information into motor actions. Here, we focus on this literature to critically discuss the proposition that prominent inhibitory projections form sensorimotor circuits. After reviewing the neural circuits of navigation across various invertebrate species, we argue that with increased neural circuit complexity and the emergence of parallel computations inhibitory circuits acquire new functions. The contribution of inhibitory neurotransmission for navigation goes beyond shaping the communication that drives motor neurons, instead, include encoding of emergent sensorimotor representations. A mechanistic understanding of the neural circuits performing sensorimotor computations in invertebrates will unravel the minimum circuit requirements driving adaptive navigation.

In this paper, a series of bicyclo[3.1.0]hexane-based nucleosides were synthesized and evaluated for their P1 receptor affinities in radioligand binding studies. The most potent derivative 30 displayed moderate A3AR affinity (Ki of 0.38 μM) and high A3R selectivity. A subset of compounds varied at 5’-position was further evaluated in functional P2Y1R assays displaying no off-target activity.

The civil construction industry is one of the sectors that most consume natural resources in the world and, consequently, one of that generate more waste. Thinking about constructive techniques that generate less impact on the environment is vital to ensure sustainable development. In this scenario, the Life Cycle Assessment (LCA) has been presented as an internationally recognized approach, that assesses the potential impact of products and services on human health and the environment, throughout its entire life cycle. Aimed to identify construction techniques and vertical closing systems that generate less impact and consumption of natural resources, the impacts generated by the life cycle of the three vertical closing systems most applied in construction sites in Brazil were compared: ceramic brick masonry system (CBr); concrete block masonry system (CBk); and structural blocks masonry system (SBk). The SBk proved to be the least impacting to the “Resource Scarcity”, “Damage to Human Health”, and “Damage to the diversity of Ecosystems” interesting areas. This performance is directly related to the use of cement CPIII type and also by the fact that the SBk consumes less concrete and mortar than the others. Already the "Water Consumption" area, the CBk was the least impacting due to the lower consumption of electricity during its life cycle. The reliability of the results was proven through a sensitivity analysis of the normalization and characterization factors, which consisted of comparing the results obtained by applying two different methodologies. It is believed that the LCA study carried out can assist in the decision-making process regarding the choice of the most sustainable construction method.

City zones have become increasingly overcrowded as a result of the extensive population widening ratio and the swift relocation of people from villages. The traffic monitoring process is a major issue in these areas due to the massive traffic flow on the roads. This research proposed a cluster-based improved authentication and communication scheme for an Intelligent Transportation System in Vehicular AdHoc Networks (VANETs). Our primary objective is to optimize resource sharing in vehicular communication. We enhanced the reliability, scalability, and stability of fast-moving VANETs by introducing cluster-based routing schemes for Vehicle-to-Vehicle (V2V) and Vehicle-to-Infrastructure (V2I) communications. We used a third-party certification authority for vehicle authentication to address security and privacy concerns. Our proposed schemes support minimizing the end-to-end (E2E) delay and route request, in addition to reducing link failure. Our schemes’ leading yield includes throughput enhancement, TCP Socket Initialization time minimization, TCP handshake response speedup, and DNS lookup improvement. The schemes are centred on short-range peer-to-peer (P2P) wireless communication in a 400-meter radius cluster. This includes innovative P2P wireless communications on VANET using minimized resources. The proposed schemes deliver a secure authentication mechanism with a securely generated vehicle authentication key provided by a certification authority. Furthermore, we have developed RESTful APIs in vehicular communication for implementation purposes, and also offered and implemented algorithms for resource sharing regarding V2V and V2I communication. Ultimately, we evaluated the performance of our experiments.

Objective: Radiomics and deep transfer learning are two popular technologies used to develop computer-aided detection and diadnosis (CAD) schemes of medical images. This study aims to investigate and compare advantages and potential limitations of applying these two technologies in developing CAD schemes. Methods: A relatively large and diverse retrospective dataset including 3,000 digital mammograms is assembled in which 1,496 images depict malignant lesions and 1,054 images depict benign lesions. Two CAD schemes are developed to classify breast lesions. The first scheme is developed using four steps namely, applying an adaptive multi-layer topographic region growing algorithm to segment lesions, computing initial radiomics features, applying a principal component algorithm to generate an optimal feature vector, and building a support vector machine classifier. The second CAD scheme is built based a pre-trained residual net architecture (ResNet50) as a transfer learning model to classify breast lesions. Both CAD schemes are trained and tested using a 10-fold cross-validation method. Several score fusion methods are also investigated to classify breast lesions. CAD classification performance is evaluated by the area under ROC curve (AUC). Results: ResNet50 model-based CAD scheme yields AUC = 0.85±0.02, which is significantly higher than radiomics feature-based CAD scheme with AUC = 0.77±0.02 (p < 0.01). Additionally, fusion of classification scores generated by two CAD schemes does not further improve classification performance. Conclusion: This study indicates that using deep transfer learning is more efficient to develop CAD schemes and enables to yield higher lesion classification performance than CAD schemes developed using radiomics-based technology.

Visible Light Communication (VLC) uses an intensity-modulation and direct-detection (IM/DD) scheme to transmit data. The light source utilized in VLC structures is constantly switched on and off rapidly, resulting in flickering. Furthermore, most of illumination systems exclude dimming support to permit customers to dim the light source to the desired stage. Therefore, the modulation scheme for information transmission in VLC should consist of flicker mitigation and dimming manage abilities. Double inverse pulse position modulation (DIPPM), sub-carrier pulse position modulation (SC-L-PPM), and M-ary variable pulse position modulation (M-VPPM) are recommended for minimizing the flicker issues and supporting an excessive degree of dimming for VLC systems. In this paper, a comparison is introduced between DIPPM, SC-L-PPM, and M-VPPM according to error performance and bit rate. In addition, a simulation is carried out to measure the optical power distribution for a LED lamp in an indoor room topology for each modulation technique. The obtained results indicated that SC-L-PPM is the best choice regarding the bit error rate (BER) and optical power distribution compared to the other two schemes. A 10^-6 BER is achieved with a very low power requirement at L=8, while a remarkable power distribution of 1.5 to 6.5 dBm is observed from 3×5×5 m³ room corners to the center, respectively. According to the bit rate, it is noticed that, M-VPPM is the most efficient one compared to the two other schemes. It achieves 2.3×10⁷ bps at signal to noise ratio (SNR) of 22 dB and M=8.

Polyhydroxyalkanoates (PHA) are microbial biopolyesters utilized as “green plastics”. Their production under controlled conditions resorts to bioreactors operated in different modes. Because PHA biosynthesis constitutes a multiphase process, both feeding strategy and bioreactor operation mode need smart adaptation. Traditional PHA production setups based on batch, repeated batch, fed-batch or cyclic fed-batch processes are often limited in productivity, or display insufficient controllability of polyester composition. For highly diluted substrate streams like it is the case for (agro)industrial waste streams, fed-batch enhanced by cell recycling were recently reported as a viable tool to increase volumetric productivity. As emerging trend, continuous fermentation processes in single-, two-, and multi-stage setups are reported, which bring the kinetics of both microbial growth and PHA accumulation into agreement with process engineering, and allow tailoring PHA´s molecular structure. Moreover, we currently witness an increasing number of CO2-based PHA production processes using cyanobacteria; these light-driven processes resort to photobioreactors similar to those used for microalgae cultivation, and can be operated both discontinuously and continuously. This development goes in parallel to the emerging use of methane and syngas as an abundantly available gaseous substrates, which also calls for bioreactor systems with optimized gas transfer. The review sheds light on the challenges of diverse PHA production processes in different bioreactor types and operational regimes using miscellaneous microbial production strains such as extremophilic Archaea, chemoheterotrophic eubacteria and phototrophic cyanobacteria. Particular emphasize is dedicated to the limitations and promises of different bioreactor-strain combinations, and to efforts devoted to upscaling these processes to industrially relevant scales.

Diagnosing skin lesions can be a challenging task. Dermatologic lesions are hard to differentiate especially for an untrained eye. However, carefully analyzing every aspect of the lesion can help clinicians reach an accurate diagnosis. If diagnosed correctly with the naked eye, many lesions can be treated without the need for further histopathology or investigations. Those aspects include morphology, color, distribution, configuration and arrangement, texture and consistency, and any evolutions or changes within the lesion. Clinicians must also contextualize those lesions into the patient’s history and overall systemic symptoms and signs. Risk factors should be taken into consideration and whether there are evolutionary changes in the lesions. Clinicians should also look for patterns as they might be the key to diagnosis. If definitive diagnosis is still not reached, biopsy, dermatoscopy, cultures, skin scrapings, patch testing, blood tests, and imaging studies may be necessary for confirmation. Integrating these methods with clinical judgment and patient history significantly enhances the accuracy of diagnosis in dermatology. Treatment for dermatologic lesions varies depending on the underlying cause.

Live streaming conferences increase the participation of a diverse audience, help defray travel costs and overcome problems related to travel restrictions. In this article, we lay out tips for implementing live-streaming in scientific meetings. We also cover legal, ethical, and technical aspects implicated with live-streaming scientific talks. To write this article, we leveraged knowledge from our experience in organizing the symposium “Deciphering the Denisovans,” presented at the 88th Annual Meeting of the American Association of Physical Anthropology (AAPA) in Cleveland, OH, in 2019, as well as literature on the topic.

Pediatric rhinosinusitis are common encountered disorders caused by different pathogenic factors or predisposing conditions with a proportion of them progressing to chronicity with a meaningful impact on quality of life and related adverse effects. A deep understanding of pathophysiology, disease course and prognosis are the fundamental building block to an appropriate management of rhinosinusitis in order to avoid risks related to complications. This review gives concise answers to clinicians who want to know "when do we need imaging?" "what do we aspect from imaging?" and "what are the appropriate imaging modalities in different settings?” in pediatric patients in order to increase the appropriateness of imaging examinations.

The study of order patterns of three equally spaced values $x_t,x_{t+d},x_{t+2d}$ in a time series is a powerful tool. The lag $d$ is changed in a wide range so that differences of frequencies of order patterns become autocorrelation functions. Similar to a spectrogram in speech analysis, four ordinal autocorrelation functions are used to visualize big data series, as for instance heart and brain activity over many hours. The method applies to real data without preprocessing, outliers and missing data do not matter. On the theoretical side, we study properties of order correlation functions and show that the four autocorrelation functions are orthogonal in a certain sense. An analysis of variance of a modified permutation entropy can be performed with four variance components associated with the functions.

Forest community connections are crucial to ensure forest stewardship and sustainability. We explored the potential of mushrooming to enable such connections in contexts where these connections have been historically broken, alienating local people from forests. Taking the case of the recent devolution of a community forest (baldios) in central Portugal to the local population, we present a five-year pilot project to rework mycology from a mushroom-centered approach to a mushroom-in-baldios approach. Mushrooms were used as an entry-point to connect the forest ecology with the challenges of governance and community building. The devised activities provided an opportunity for people inside and outside the local community to adventure into the woods and find out more about their socio-ecological history, develop communal and convivial relationships and engage in the responsible gathering of wild mushrooms. However, the hosting of mushroomers to know, value and engage with the community forest recovery has constantly working against the enclosure of mushrooms to provide marketable forms of leisure. The outcome of these activities depends on the relationships established between mushrooms, mycologists, local administrators, commoners and poachers, all operating within a framework that favors the eradication of resources instead of long-term relationships that sustain places.

Keywords: Forest management; sustainability; FSC; PEFC; research; market share

(1) In an era where sustainable behavior is increasingly crucial, understanding the discrepancy between individuals' sustainability-oriented values and their actual behaviors, known as the inner-outer gap, is vital. This study explores the potential of the Tripartite Structure of Sustainability (TSS) framework to address this gap within the context of sustainable education. By reviewing literature from the databases APA, ERIC, and Web of Science, we systematically examined factors influencing sustainable actions. (2) Employing a qualitative content analysis approach, we analyzed 56 articles over a 15-year period, identifying 83 factors that either bridge or reinforce the inner-outer gap. These factors were categorized within the TSS framework, which segments sustainability-oriented actions into individual, social, and self-transcendent domains, alongside their activation points: stable, situational, or automated. (3) Our analysis revealed that self-focused factors often reinforce the gap, suggesting a hindrance to sustainable behavior. Conversely, self-transcendent factors consistently bridged the gap, promoting sustainability. Social factors showed variable impacts based on the ethical and sustainable context they were placed in, suggesting that the social environment's orientation significantly influences sustainable behavior. (4) The study concludes that the TSS framework offers a promising approach to advancing sustainability in education by facilitating a paradigm shift towards holistic and interconnected perspectives. This shift is critical for fostering sustainable behaviors, thereby contributing to the field of educational psychology and offering practical implications for educators aiming to nurture a sustainable future.

This paper reviews the pioneering work related to the generation of a sequence of prompts in Pretrained Language Models (PLMs) to automatically complete a complex writing task. The paper identifies the main categories of automated multi-step prompting and discusses their advantages and disadvantages. The paper also proposes an additional approach for automated multi-step prompting with iterative four main phases: in the first phase a sequence of prompts is geared to elicit the structure of the requested task. This is done by identifying the task’s main parts, the general contents of the different parts and their precedence relations. The structure of each main part is iteratively explored to find secondary and tertiary parts if they exist. A second phase is followed by a sequence of prompts that fill in the primary, secondary, and tertiary parts, and seek to fine-tune the result. The third phase reviews the generated text and criticizes it. Based on this criticism a revision is prepared. The fourth phase is fine-tuning the document, with emphasis on section length and text tone. Future research could deal with the system identification of points where the system should initiate interaction with the user for desired feedback and guidance.

This paper proposes an encryption scheme for high pixel density images. Based on the application of the quantum random walk algorithm, the Long short-term memory (LSTM) can effectively solve the problem of low efficiency of the quantum random walk algorithm in generating large-scale pseudorandom matrices, and further improve the statistical properties of the pseudorandom matrices required for encryption. The LSTM is then divided into columns and fed into the LSTM in order for training. Due to the randomness of the input matrix, the LSTM cannot be trained effectively, so the output matrix is predicted to be highly random. The LSTM prediction matrix of the same size as the key matrix is generated based on the pixel density of the image to be encrypted, which can effectively complete the encryption of the image. In the statistical performance test, the proposed encryption scheme achieves an average information entropy of 7.9992, an average number of pixels changed rate (NPCR) of 99.6231%, an average uniform average change intensity (UACI) of 33.6029% and an average correlation of 0.0032. Finally, various noise simulation tests are also conducted to verify its robustness in real-world applications where common noise and attack interference are encountered.

Public Transport has been seen since ages as the most environmentally sustainable mode of transport. The users of public transport are diverse and have different socio-economic character. Hence the public transport which is not only supposed to be environmentally sustainable but also envisaged to ensure equity amongst various stakeholders of society like the females, elderly and other vulnerable groups through its service. Gender in binary terms of being differentiated based on men and women is a social construct. Public transport systems in developing countries like India witness socio-cultural factors that shape the experience of women in public spaces by social norms extant in society. Along with this, gender-based issues related to public transport are social and behavioural shortcomings as a consequence of a lack of gender sensitivity. On similar lines, elderly have a negative experience involving safety threats, physical and psychological discomfort while accessing public transport systems. The literature published regarding such issues on the gender and elderly question in public transport systems have been studied and has been brought forth under a stand- alone narrative literature review. A literature review is a prerequisite to conducting either stand-alone reviews or as a preliminary study to be supported with quantitative or qualitative analysis. Here, a stand-alone literature review concerning issues in the public transport system in India has been performed. A narrative type of review is conducted to provide an overview of pre- existing published literature. Narrative overviews are useful educational articles as they help present a broad perspective on a topic and often define the development of a problem and/or ways to manage it. The semi-systematic or narrative-review approach is designed for topics that have been theorized differently and studied within diverse disciplines making it unfavourable to study under a full systematic-review process which majorly caters to reviewing quantitative researches. As narrative-styled literature reviews prefer a semi- systematic data collection method, utmost care has been taken to include perspectives from diverse disciplines. The scope of this review is restricted to summarizing the Indian policies, schemes of public transport in light of socio-equity consideration while narrowing the inherent discrepancies within the socio-cultural ethos of the Indian society which influences socio-equity consideration in public spaces in general and the modes of public transport in particular. Research articles from electronic databases were selected based on relevance to understand the issues this viewpoint, their essential findings and possible recommendations are formulated to provide a comprehensive summary of previous researches.

The Inefficient water use, varying and low productivity in Kenya public irrigation schemes is a major concern. It is therefore necessary to periodically monitor and evaluate the performance of public irrigation schemes. The performance of public irrigation in western Kenya was assessed by combining benchmarking methodology and principal component analysis. The aim was to quantify and rank the performance of pumped public irrigation schemes in Kenya. Eleven benchmarking indicators were computed for the period from 2012 to 2016 and compared to global benchmark values. The indicators used fall under agricultural productivity, water supply and financial performance categories. The computed agricultural productivity was 36%–51% in Ahero, 23%–42% in West Kano and 26%–50% Bunyala irrigation scheme. Water supply performance in Ahero, West Kano and Bunyala irrigation schemes varied from 24% to 58%, 3% to 49% and 19% to 43% respectively. Financial performance varied from 46% to 54% in Ahero, 25% to 32% in West Kano and 54%–56% in Bunyala irrigation scheme. An average overall performance efficiency of 46%, 39% and 31% was obtained in Ahero, Bunyala and West Kano irrigation schemes respectively. The performance of the irrigation schemes is very poor and measures on improving performance are needed.

Postdocs who land faculty jobs at research-intensive institutions need to juggle several new large-scale tasks: identifying space and equipment needs for their lab, negotiating the hiring package, outfitting the lab with supplies, building a team, and learning to manage time in ways that can promote productivity and happiness. Here we share tips to help new hires think clearly about each of these tasks.

Calibrating ecological models or making decisions with them is an optimisation problem with challenging methodological issues. Depending on the optimisation formulation, there may be a large variety of optimisation configurations (e.g. multiple objectives, constraints, stochastic criteria) and finding a single acceptable solution may be difficult. The challenges are exacerbated by the high computational cost and the non linear or elusive mathematical properties that increased with the complexity of numerical models. From the feedbacks of practitioners, the need for a guideline for conducting optimisation of complex models has emerged. In this context, we propose a practical guide for the complex model optimisation process, covering both calibration and decision-making. The guide sets out the workflow with recommendations for each step based on existing tools and methods usually scattered throughout the literature. This guide is accompanied with an ODDO template (Overview, Design, Details of Optimisation) to standardise the published description of model-based optimisation and suggests research directions.

The paper describes schemes for the resource-efficient generation of twiddle factors for the fixed-radix version of the ubiquitous fast Fourier transform (FFT) algorithm. The schemes, which are targeted at a parallel implementation of the FFT, provide one with the facility for trading off arithmetic complexity, as expressed in terms of the required numbers of multiplications and additions (or subtractions), against the memory requirement, as expressed in terms of the amount of random access memory (RAM) required for constructing the look-up tables (LUTs) needed for the storage of the two twiddle factor components – one component being derived from the sine function and the other from the cosine function. Examples are provided which illustrate the advantages and disadvantages of each scheme – which are very much dependent upon the length of the FFT to be computed – for both the single-level and multi-level LUTs, highlighting those situations where their adoption might be most appropriate. More specifically, it is seen that the adoption of a multi‑level LUT scheme may be used to facilitate significant reductions in memory – namely, from an O(N) to an memory requirement, for the case of an N‑point FFT, where β ≥ 2 corresponds to the number of distinct angular resolutions used – at a relatively small cost in terms of increased FFT latency and arithmetic complexity.

In order to remain competitive in the highly competitive construction industry, it is crucial for construction organizations to continually improve their overall performance, as project performance is a key determinant of their relevance. Despite the industry's competitiveness and risk, it has been reported that the construction industry has the lowest return margins compared to other industries (Jackson, 1999), suggesting that the project performance of construction organizations in the industry has not been up to par. This issue can be attributed to several factors, with motivation being the primary factor. Unfortunately, motivation is often disregarded in the construction industry due to the short duration of many construction projects and the high rate of employee turnover. The impact of employee dissatisfaction and related work attitudinal problems on performance in the construction industry is a matter of concern, particularly in developing countries where working conditions may be unappealing. The severity of this issue cannot be overstated.The objective of this research is to evaluate the effectiveness of motivational techniques in enhancing project performance in Nigeria. The study employed a survey research design and targeted the management staff of construction firms in Lagos State, Nigeria. The questionnaire was used to collect data, and the respondents were purposively selected from the population. Data analysis was conducted using percentage, mean ranking, and chi-square. The findings reveal that the opportunity to learn new skills, with a mean score of 0.85, and wage increment, with a mean score of 0.82, were the most widely adopted motivational techniques for management staff and skilled labor, respectively, in construction firms. Additionally, the study found that most of the motivational schemes tested did not produce statistically significant results, indicating low adoption and limited effectiveness in enhancing project performance. As a result, it is suggested that construction companies in Nigeria should implement and enforce financial and non-financial incentives to enhance the performance of their employees and consequently, improve project performance.

In this study, we explored the performance of the cumulus convection parameterization schemes of Regional Climate Modeling System (RegCM) towards the Indian summer monsoon (ISM) of a catastrophic year through various numerical experiments conducted with different convection schemes (Kuo, Grell amd MIT) in RegCM. The model is integrated at 60KM horizontal resolution over Indian region and forced with NCEP/NCAR reanalysis. The simulated temperature at 2m and the wind at 10m are validated against the forced data and the total precipitation is compared with the Global Precipitation Climatology Centre (GPCC) observations. We find that the simulation with MIT convection scheme is close to the GPCC data and NCEP/NCAR reanalysis. Our results with three convection schemes suggest that the RegCM with MIT convection scheme successfully simulated some characteristics of ISM of a catastrophic year and may be further examined with more number of convection schemes to customize which convection scheme is much better.

The MET proto-oncogene encodes a pivotal tyrosine kinase receptor, binding the hepatocyte growth factor (HGF, also known as scatter factor, SF) and governing essential biological processes such as organogenesis, tissue repair, and angiogenesis. The pleiotropic physiological functions of MET explain its diverse role in cancer progression in a broad range of tumors; genetic/epigenetic alterations of MET drive tumor cell dissemination, metastasis, and acquired resistance to conventional and targeted therapies. Therefore, targeting MET emerged as a promising strategy, and many efforts were devoted to identifying the optimal way of hampering MET signaling. Despite encouraging results, however, the complexity of MET's functions in oncogenesis yields intriguing observations, fostering a humbler stance on our comprehension. This review explores recent discoveries concerning MET alterations in cancer, elucidating their biological repercussions, discussing therapeutic avenues, and outlining future directions. By contextualizing the research question and articulating the study's purpose, this work navigates MET biology's intricacies in cancer, offering a comprehensive perspective.

When attempting to quantify future harms caused by carbon emissions and to set appropriate energy policies, it has been argued that the most important metric is the number of human deaths caused by climate change. Several studies have attempted to overcome the uncertainties associated with such forecasting. In this article, approaches to estimating future human deaths tolls from climate change are compared and synthesized, and implications for energy policy are considered. Several studies are consistent with the “1000-ton rule,” according to which a future person is killed every time 1000 tons of fossil carbon are burned (order-of-magnitude estimate). If warming reaches or exceeds 2°C this century, mainly richer humans will be responsible for killing roughly 1 billion mainly poorer humans through anthropogenic global warming. Such mass manslaughter is clearly unacceptable. On this basis, relatively aggressive energy policies are summarized that would enable immediate and substantive decreases to carbon emissions. The limitations to such calculations are outlined and future work is recommended to accelerate the decarbonization of the global economy while minimizing the number of sacrificed human lives.

The importance of statistics in biological research is inevitable. The appliance of statistics is the most powerful tool to support the scientific hypothesis and to give credibility to biological research methodology, to interpret convoluted explanations and conclusions based on the research findings. The evidences from literatures point the persistent statistical errors, selection of non-proper statistical test with the consequence of misinterpretation of the scientific results which are published in international journals. One of the most extensively used statistical tests in the field of biology (preclinical and clinical) is analysis of variance (ANOVA). ANOVA test is in place of multiple T-tests to compare the means of more than two groups at a time; and there are some important points which biologists should be aware of them to avoid possible misinterpretation of results with the consequence of wrong conclusion. Accordingly, the aim of the current review is to help biologists to understand the basic concepts of ANOVA test and reach to a more valid interpretation of achieved results.

To fully appreciate genetics, one must understand the link between genotype (DNA sequence) and phenotype (observable characteristics). Advances in high-throughput genomic sequencing technologies and applications, so-called “-omics”, have made genetic sequencing readily available across fields in biology from applications in non-traditional study organisms to precision medicine. Thus, understanding these tools is critical for any biologist, especially those early in their career. This comprehensive review discusses the chronological development of different sequencing methods, the bioinformatics steps to analyzing this data, and social and ethical issues raised by these techniques that must be discussed and evaluated.

Large datasets that enable researchers to perform investigations with unprecedented rigor are growing increasingly common in neuroimaging. Due to the simultaneous increasing popularity of open science, these state-of-the-art datasets are more accessible than ever to researchers around the world. While analysis of these samples has pushed the field forward, they pose a new set of challenges that might cause difficulties for novice users. Here, we offer practical tips for working with large datasets from the end-user’s perspective. We cover all aspects of the data life cycle: from what to consider when downloading and storing the data, to tips on how to become acquainted with a dataset one did not collect, to what to share when communicating results. This manuscript serves as a practical guide one can use when working with large neuroimaging datasets, thus dissolving barriers to scientific discovery.

How crucial is big data in contemporary molecular design? In this publication we elucidate fundamental concepts and terminology in this field, critically addressing overlooked issues. We thoroughly examine the size, accessibility, quality, and structural aspects of big data alongside the primary methodologies employed for their analysis. Within chemical compounds, properties and descriptors represent two distinct data types, forming the basis for categorizing molecular big data. The primary objective of chemistry is property production, which means we are searching for novel drugs or materials rather than chemical compounds, and big data is the central issue of this philosophy. The increasing availability of data in computer-aided technology propels advancements in artificial intelligence (AI), machine learning (ML), and deep learning (DL). Accordingly, a broad chemical audience must comprehend these methods to understand data-centered chemistry. Thus, we aim to systemize big data issues through a simple illustrative framework with fundamental descriptor categories: coding, computer-generated descriptors, and property correlates. Although we employ computer-generated descriptors as big data for predictions, the measured data are irreplaceable for achieving high-quality and reliable outcomes and controlling molecular effects. The scarcity of property data remains a significant hurdle limiting comprehensive studies on the structure-property relationships within big data. Accordingly, guided by pragmatics not-so-big data is an option for drug design. We presented also a brief review of the recent big data literature.

Building Information Modeling (BIM) has been one of the overwhelming trends in the worldwide. In Korea, from 2012, BIM application to the public construction projects worth more than $40 million was mandated. However, despite the policy, many public owners have hesitated to apply BIM to their projects. They generally view BIM very complex to manage and difficult to understand. While there have been diverse BIM guides as a reference, most of them have developed from BIM suppliers’ perspective involving certain deficiency in meeting the public owners’ taste. The public owners have addressed the necessity for developing an owner-oriented BIM guide on which they can understand the overall BIM procurement process thereby efficiently preparing their BIM service contracts. The main objective of this study is to develop the structure and contents guidance of the new guide to be developed that follows the public business process and mitigates the deficiency. To meet the research objective, a number of domestic and international BIM guides were analyzed and workshops were operated twice with the 12 BIM experts from the Korean construction industry. As a result of the study, a four-staged guide structure was developed consisting of the BIM service Scoping, Tendering, Executing, and Wrapping-up (STEW) guides.

Abstract Safflower (Carthamus tinctorius L.) is a multipurpose minor crop consumed by developed and developing nations around the world with a limited research fund and genetic resources. Genomic selection (GS) is an effective modern breeding tool which could help to fast track the genetic diversity preserved in genebank collections to facilitate rapid and efficient germplasm improvement and variety development. In the present study, we simulated four GS strategies to compare genetic gains and inbreeding rates during breeding cycles in a safflower recurrent selection breeding program targeting grain yield (GY) and seed oil content (OL). We observed positive genetic gains over cycles in all four GS strategies, where the first cycle delivered the largest genetic gain. Single traits GS strategies had the greatest gain for the target trait but with very limited genetic improvement for the other trait. Simultaneous selection for GY and OL via index indicated higher gains for both traits than crossing between the two single trait independent culling strategies. The the multi-trati GS strategy with inbreeding control (GS_GY+OL+Rel) showed lower inbreeding rate but similar gain compared to GS_GY+OL (without inbreeding control) after few cycles. Our finding lay the foundation for the future safflower GS breeding.

Purpose: A number of imaging readout schemes have been proposed for renal arterial spin labelling (ASL) to quantify kidney cortex perfusion, including gradient echo based methods of balanced fast field echo (bFFE) and gradient-echo echo-planar imaging (GE-EPI), or spin echo based schemes of spin-echo echo planar imaging (SE-EPI) and turbo spin-echo (TSE). Here, we compare these imaging schemes to evaluate the optimal imaging scheme for pulsed ASL (PASL) assessment of human kidney cortex perfusion at 3 T. Methods: Ten healthy volunteers with normal renal function were scanned using each 2D multislice imaging scheme, in combination with a respiratory triggered FAIR (flow-sensitive alternating inversion recovery) ASL scheme on a 3 T Philips Achieva scanner. All volunteers returned for a second identical scan session within two weeks of the first scan session. Comparisons were made between the imaging schemes in terms of perfusion weighted image (PWI) signal-to-noise ratio (SNR) and perfusion quantification, temporal SNR (tSNR), spatial coverage, and repeatability. Results: For each imaging scheme, renal cortex perfusion was calculated (bFFE: 276 ± 29 mL/100 g/min, GE-EPI: 222 ± 18 mL/100 g/min, SE-EPI: 201 ± 36 mL/100 g/min, TSE: 200 ± 20 mL/100 g/min). Perfusion was found to be higher for GE based readouts compared to SE based readouts, with significantly higher measured perfusion for the bFFE readout compared to all other schemes (P < 0.05), attributed to the greater vascular signal present. Despite the PWI-SNR being significantly lower for SE-EPI compared to all other schemes (P < 0.05), the SE-EPI readout gave the highest tSNR and was found to be the most reproducible scheme for the assessment of kidney cortex, with a CoV of 17.2%, whilst minimizing variability of the perfusion weighted signal across slices for whole kidney perfusion assessment. Conclusion: For the assessment of kidney cortex perfusion, SE-EPI provides optimal tSNR, minimal variability across slices and repeatable data acquired in a short scan time with low specific absorption rate.

The development of numerical simulations is potentially useful in predicting the most suitable manufacturing process and ultimately improving product quality. Seamless pipes are manufactured by rotary piercing process in which round bars are fed between two rolls and pierced by a stationary plug. During this process, the material undergoes severe deformation which renders it impractical to be modelled and analysed with conventional finite element methods. In this paper, three dimensional numerical simulations of the piercing process are performed with Arbitrary Lagrangian-Eulerian (ALE) Formulation in LS DYNA software. Details about the material model as well as the elements formulations are elaborated here and mesh sensitivity analysis was performed. The results of the numerical simulations are in good agreement with experimental data found in the literature and the validity of the analysis method is confirmed. The effects of varying workpiece velocity, process temperature, and wall thickness on the maximum stress levels of the product material/pipes are investigated by performing simulations of sixty scenarios. Three dimensional surface plots are generated which can be utilized to predict the maximum stress value at any given combination of the three parameters.

Directed evolution methods are becoming increasingly popular, as they are extremely powerful toward developing new biomolecules with altered/novel activities, e.g., proteins with new catalytic functions or substrate specificities, and nucleic acids that recognize an intended target. Especially useful are systems that have incorporated continuous evolution, where the protein to be evolved undergoes continuous mutagenesis to evolve a desired trait with little to no input from the researcher once the system is started. However, continuous evolution methods can be challenging to implement in the lab and daunting for researchers to invest time and resources. Our intent is to provide basic information and helpful suggestions that we have gained from our experience with bacterial phage-assisted continuous evolution (PACE). Specifically, we review factors to consider before adopting PACE for a given evolution scheme, different types of selection circuits that can be utilized with particular focus on the PACE-B1H selection system, what optimization of a PACE selection circuit may look like using directed evolution of ME47 as a case study, and additional techniques that may be incorporated into a PACE experiment. With this information, researchers will be better equipped to determine if PACE is a valid strategy to use to evolve their proteins and how to set up a valid selection circuit.

The “Pay-as-you-throw” scheme, PAYT, is an economic instrument of waste management that implements the “polluter pays” principle by charging inhabitants of municipalities according to the amount of residual, organic and bulky waste they send for third-party waste management. When combined with well-developed infrastructure to collect the different waste fractions (residual waste, paper and cardboard, plastics, bio waste, green cuttings, many recyclables) as well as with a good level of citizen’s awareness, its performance has frequently been linked to high collection rates of recyclables. However, the establishment and operation of PAYT systems can require significant resource inputs from municipalities. In this paper, PAYT is analysed through a case study from the German County of Aschaffenburg, covering nearly 20 years of implementation across 173,000 inhabitants. Key performance indicators applied include temporal trends in the county’s recyclables collection rate, waste treatment fees for residents and municipal waste management costs, benchmarked against German municipalities not implementing PAYT.