The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Radial nerve palsies present a challenging clinical scenario, often leading to substantial functional impairment. This study focuses on evaluating the outcomes of tendon transfer surgeries in patients with post-traumatic radial nerve injuries. The radial nerve, vital for upper limb movements, faces various etiologies such as trauma, compression, or idiopathy. Patients with radial nerve palsy encounter difficulties in daily activities, emphasizing the need for effective management strategies. The research introduces a novel evaluation protocol, aiming to comprehensively assess tendon transfer outcomes. This protocol incorporates functional movements of wrist and finger joints, encompassing both objective and subjective parameters. The retrospective study includes eleven patients treated between 2010 and 2022, with a minimum follow-up of one year post-surgery. Tendon transfers demonstrated positive results. The evaluation protocol covers a wide range of parameters, including wrist and finger mobility, thumb function, grip strength, and patient satisfaction. The results indicate successful restoration of motor function, with an average grip strength of 70% compared to the healthy arm. The proposed evaluation protocol facilitates standardized and reproducible assessment, minimizing subjective errors in clinical evaluations. Despite the study's limitations, such as a relatively small sample size, the findings underscore the effectiveness of tendon transfers in treating radial nerve palsies. The introduced evaluation scheme provides a comprehensive and reproducible approach to assess outcomes, contributing to the global standardization of tendon transfer assessments in radial nerve injuries.

Introduction Blunt carotid injuries (BCI) in pediatric trauma are quite rare. Due to the low number of cases, only a few reports and studies have been conducted on this topic. This review will discuss how frequent BCI/ BCVI on pediatric patients after blunt trauma is, what routine diagnostics look like, if a CT/ CTA scan on pediatric patients after blunt trauma is always necessary and if there are any negative health effects? Methods This literature review includes reviews, systematic reviews, case reports and original studies in english language between 1999 and 2020 that have dealt with pediatric blunt trauma and the diagnostics of BCI and BCVI. Furthermore, publications on the risk of radiation exposure on children were included in the study. For literature research, Medline (PubMed) and the Cochrane library were used. Results Pediatric BCI/ BCVI, shows an overall incidence between 0.03 – 0.5% of confirmed BCI/ BCVI cases due to pediatric blunt trauma. 1.1 – 3.5% of pediatric blunt trauma patients underwent CTA to detect BCI. Only 0.17 – 1.2% of all CTA scans shows a positive diagnosis for BCI. In children, the median volume CT dose index on a non-contrast head CT is 33 milligray, a computed tomography angiography needs at least 138 mGy. A cumulative doses of about 50 mGy almost triples the risk of leukemia, and doses of about 60 mGy triples the risk of brain cancer. Discussion Knowing that a BCI could have extensive neurologic consequences for children, it is necessary to evaluate routine pediatric diagnostics after blunt trauma. Computed tomography scans (CT) and computed tomography angiography (CTA) are mostly used in routine BCI diagnostics. However, since radiation exposure in children should be as low as reasonably achievable, it should be asked if other diagnostic methods could be used to identify risk groups. Trauma guidelines and clinical scores like the McGovern score are reflect established BCI screening options, as well as using duplex ultrasound.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

Bioenergy produced from perennial feedstocks such as woody biomass could serve as an opportunity to strengthen local and regional economies and also jointly produce various environmental services. In order to assess the potential for biomass- based bioenergy, it’s essential to characterize the interest that potential biomass suppliers have in such an endeavor. In the U.S. Great Plains region, this largely means assessing relevant perceptions of farmers and ranchers. We conducted a series of farmer and rancher oriented focus groups in North Dakota, South Dakota, Nebraska and Kansas to qualitatively explore opinions about the role that trees can play in agriculture and interest in woody biomass systems within existing Northern Great Plains (NGP) farms and ranches. Our findings suggest that farmer and ranchers generally value the role that trees, or tree-based practices like windbreaks can play in agriculture particularly on marginal farmland in terms of conservation or crop protection. Yet relative to the potential of trees as a biomass crop there is a distinct lack of knowledge and skepticism. Farmers and ranchers also noted variable degrees of risk concern and uncertainty regarding investing in tree-based systems, as well as a number of perceived external market related constraints to integrating trees within their managed systems. Most of the participants recognized that if biomass production or an increase in tree planting and management in general were to expand in the NGP region, government programs would likely be required to provide much needed technical guidance and financial incentives. As the NGP regional bioeconomy continues to emerge and expand, private and public investment relative to niche bioenergy feedstocks such as woody biomass should address the type of information needs that farmers and ranchers have relative to integrating biomass production into existing farm and ranch systems.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The research deals with the particularities of the initiation in the sport of kin ball, of 94 students (54 boys and 40 girls), without a history of practicing the sport intensively, and the measure of the influence of some components of the motor capacity. Kin ball is a sport that appeared in Canada, in an academic setting and can become an alternative sport in the common university curricula in Romania. The research was carried out in 4 research groups in 2019 and 2022, two of boys and two of girls, similarly, before and after the declaration of the acute phase of the Covid-19 Pandemic, generating physical activity constraints. The originality of the research refers to the initiation, unprecedented in Romania, in the Kin ball sport, through 20 training sessions, carried out in 10-day stages and the evaluation of some motor skills on the subjects. During the experiment, the following components were tested pre- and post-intervention Kin-Ball: palmar muscle strength using the dynamometer, general resistance by running as long as possible for 2 min and general coordination function - body balance, by the Matorin test. The statistical calculation included the application of the Kolmogorov-Smirnov test, depending on which parametric or non-parametric statistical significance tests were applied and the estimation of the size of the intervention effect. The results highlighted particularities of initiation in Kin ball, but also significant differences (p<0.05) in all measurements performed in 2022. The tests in 2019 recorded both significant and statistically insignificant differences, also highlighted by the calculation of the d indicator of to Cohen. The lower initial level of all motor components measured in 2022 and their significant improvement represent aspects that can be understood as collateral effects of the lack of movement during the pandemic.

Composites, and especially carbon fiber reinforced plastics (CFRPs), are increasingly used in the automotive, aerospace, and aviation industries, and as a result, CFRP production has increased dramatically, leading to a corresponding increase of waste. Landfill and incineration of waste are likely to be restricted as a result of the legislation, thus highlighting the need for efficient recycling methods for CFRPs. However, the recycling of CFRP is very challenging, mainly due to the difficulty of removing the thermosetting matrix. This study reports a pre-screening of the solvolysis recycling process for CFRPs based on the mechanical properties of the recovered fibers. To this end, solvolysis tests were conducted on unidirectional CFRP samples under supercritical and subcritical conditions using acetone and water. The solvolysis tests were conducted for various conditions of temperature, pressure, and reaction time. The efficiency of the recycling processes has been evaluated through a morphological and a mechanical characterization of the recovered fibers. In most cases, the decomposition efficiency of the epoxy resin, measured in terms of mass, ranged between 90 and 100%. Moreover, the scanning electron microscopy images of the recovered fibers showed negligible traces of resin residues and no detectable signs of physical damage or any changes in morphology with regard to diameter. Finally, the single-fiber tension tests revealed that that the recovered fibers retained more than 61% of their initial Young's modulus and 70% of their tensile strength.

Chloroplasts are ancient organelles responsible for photosynthesis and various biosynthetic functions essential to most life on Earth. Many of these functions require tightly controlled regulatory processes to maintain homeostasis at the protein level. One such regulatory mechanism is the ubiquitin-proteasome system whose fundamental role is increasingly emerging in chloroplasts. In particular, the role of E3 ubiquitin ligases as determinants in the ubiquitination and degradation of specific intra-chloroplast proteins. Here, we highlight recent advances in understanding the roles of plant E3 ubiquitin ligases in chloroplast function.

Background: Extracellular Vesicles are pivotal mediators in intercellular communication, facilitating the exchange of biological information among healthy, pathological and tumor cells. Between the diverse subtypes of extracellular vesicles, exosomes have unique properties, clinical and therapeutical applications, even towards cancer. Breast cancer ranks as one of the most prevalent malignancies across the globe. Both the tumor core and its surrounding microenvironment engage in a complex, orchestrated interaction that facilitates the cancer’s growth and spread. Methods: The most valuable and significant PubMed Literature about extracellular vesicles and adipose–derived stem cells exosomes was selected and analyzed in order to report their biological properties and potential applications, in particular on the Triple–Negative Breast Cancer. Results: Adipose–derived stem cells exosomes represent a potential tool to target the tumor core of the Triple–Negative Breast Cancer, its microenvironment and surrounding tissues including metastasis. The authors are developing a supportive Triple–Adipose–derived stem cells Exosomes [T.A.E.] Technology against breast cancer in order to perform a selective preconditioning of the cancer before or while the traditional oncological treatments are running. Conclusion: The possibility to exploit the impact of Adipose–derived stem cells exosomes within the T.A.E. Technology against the Triple–Negative breast cancer is real, highlighting a new era for supportive measures against breast cancer.Keywords: Extracellular vesicles; Exosomes; Adipose–derived stem cells, Tumor microenvironment, Triple–Negative Breast Cancer, T.A.E. Technology.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

The present paper describes the development of a prosthetic hand based on the human hand anatomy. The hand phalanges are printed by using 3D printed with Polylactic Acid material. One of the main contributions is the investigation on the prosthetic hand joins; the proposed design enables to create personalized joins that allow the prosthetic hand a high level of movement by increasing the degrees of freedom of the fingers. Moreover, the driven wire tendons show a progressive grasping movement, being the friction of the tendons with the phalanges very low. Another important point is the use of force sensitive resistors for simulating the hand touch pressure. These are used for the grasping stop simulating touch pressure of the fingers. Surface Electromyogram (EMG) sensors allow the user to control the prosthetic hand grasping start. Their use may provide the prosthetic hand the possibility of classification of the hand movements. The practical results included in the paper prove the importance of the soft joins for the object manipulation and to get adapted to the object surface. Finally, the force sensitive sensors allow the prosthesis to actuate with more naturalness by adding conditions and classifications to the Electromyogram sensor.

The importance of contact with nature for human health was confirmed by numerous research. One of the sometimes neglected fields is the landscape design of hospital premises. This study focuses on the perception and preferences of prospective patients regarding the hospital site design. The methodology included anonymous survey with images and lists of adjectives. The online questionnaire was distributed using e-mails and social media from 4th May to 8th July 2024. The objective was to include all age groups. The results confirm previous studies and demonstrate the importance of landscape architecture design of hospital premises for the well-being of patients. The findings may inform the design of hospital sites.

The objective was to assess the instrumental validity and the test-retest reliability of a low-cost hand-held push dynamometer adapted from a load-cell based hanging scale (tHHD) to collect compressive forces in different ranges of compressive forces. Three independent raters applied 50 pre-established compressions each on the tHHD centered on a force platform in 3 distinct ranges: ~70 N, ~160 N, ~250 N. Knee isometric strength was also assessed on 19 subjects in two sessions (48h apart) using the tHHD anchored by an inelastic adjustable strap. Knee extension and flexion were assessed with the participant seated on a chair with the feet resting on the floor, knees, and hips flexed at 90°. The isometric force peaks were recorded and compared. The ICC and the Cronbach’s α showed excellent consistency and agreement for both instrumental validity and test-retest reliability, as the correlation and determination coefficients. The SEM and the MDC analysis returned adequate low values with a coefficient of variation less than 5%. The Bland-Altman results showed consistency and high levels of agreement. The tHHD is a valid method to assess the knee isometric strength, showing portability, cost-effectiveness, and user-friendly interface to provide an effective form to assess the knee isometric strength.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

This study investigates the utilization of innovative green composites made from hemp shiv, a waste by-product of hemp cultivation, with the aim of promoting sustainability within the construction industry. The manufacturing method involve the application of pressure in a mold to create the samples. These materials were produced using an environmentally friendly binder consisting of colophony, arabic gum and corn starch, moreover white glue and bioepoxy are also used to compare with the green resins. Three different binder compositions for the specimens. The samples underwent mechanical testing through tensile and bending assessments, and their performance was compared to that of non-green binders to validate the effectiveness of the manufacturing processes. The study revealed that decreasing the moisture content during the curing process is crucial for improving the mechanical properties. The best results were achieved when using arabic gum as a binder, yielding a tensile strength of 2.16 MPa and a bending strength of 5.25 MPa, with a composition of 62.5% hemp shiv and a manufacturing process involving a pressure of 5 MPa.

Although a lot of research has been carried out on hand sanitizer as an effort to prevent Covid-19, there is still limited research on non-alcoholic hand sanitizer lotion from the brown algae Scytosiphon lomentaria (S. lomentaria) as a raw material that provides antibacterial effects and maintains healthy skin. Therefore, this study aimed to analyze microbial inhibitory ability, physical and chemical characteristics of hand sanitizer lotion made from S. lomentaria algae. S. lomentaria powder was tested for phytochemicals, total phenolic content, free radical scavenging activity (IC50), and antibacterial tests. S. lomentaria slurry was prepared by adding distilled water (1:1) for lotion preparations in four treatment groups, such as normal control (lotion base without adding algae), lotion with the addition of algae 20%, 30%, and 40%. The lotion preparations for each treatment group were tested for antibacterial activity of Staphylococcus aureus and Escherichia coli, phytochemicals, pH, adhesion, spreadability, homogeneity, emulsion type, and hedonic. S. lomentaria powder contains bioactive polyphenolic compounds with a total phenolic content of 117.70±1.40 mg GAE/g dry weight and an IC50 value of 455±3.4 ppm, while lotion with the addition of S. lomentaria contains polyphenols and saponins The best treatment was shown by 40% S. lomentaria hand sanitizer lotion with inhibition of 6.30 ± 0.64 mm E. coli, 6.85 ± 1.12 mm S. aureus, hedonic test for color, texture and absorption with likes to likes very much level, neutral pH, greenish-white color, O/W emulsion type, high adhesion, homogeneous, and easily absorbed by the skin. This research can be an alternative reference in making non-alcoholic hand sanitizer lotion that is safe for the skin.

This review summarizes studies dedicated to the assessment of microvascular function based on microcirculatory oscillations monitored by the FMSF technique. Two approaches are presented. The first approach uses oscillatory parameters measured under normoxia conditions, expressed as flowmotion (FM), vasomotion (VM), and the normoxia oscillatory index (NOI). These parameters have been used for identification of impaired microcirculatory oscillations associated with intense physical exercise, post-COVID syndrome, psychological stress, and erectile dysfunction. The second approach involves characterization of the microcirculatory response to hypoxia based on the measurement of hypoxia sensitivity (HS). The HS parameter is used to characterize microvascular complications in diabetes, such as diabetic kidney disease and diabetic foot ulcers. Based on research conducted by the authors of this review, the FMSF parameter ranges characterizing microvascular function are presented. The diagnostic approach to assessing microvascular function based on flowmotion monitored by the FMSF technique has a wide range of applications and potential to be integrated into widespread medical practice.

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

Abstract: Hand gestures are an essential kind of nonverbal communication that let people engage and be expressive with one another. As technology has progressed, hand gesture recognition systems have become an important field of study, providing a link between human activities and artificial intelligence. An overview of the field of hand gesture recognition systems is given in this abstract, along with an explanation of its importance, difficulties, and possible uses. This abstract begins by examining the role that hand gestures have in communication. It then goes on to show the cultural significance and wide range of variations in gestural expressions that occur in many contexts and societies. Artificial intelligence systems face a unique problem in comprehending and interpreting these motions, which calls for the combination of computer vision, machine learning, and pattern recognition approaches. The abstract goes on to address why people develop hand motions. The purpose behind creating systems to recognize hand gestures is also covered in the abstract, with a focus on how these systems could improve human-computer interaction in several fields, including robotics, virtual reality, healthcare, and assistive technologies. These systems have the potential to enhance accessibility, efficiency, and user experience by allowing people to engage with devices and interfaces naturally and intuitively. The abstract also discusses environmental elements including backdrop clutter and lighting, as well as the technological difficulties in identifying and understanding hand gestures, which include variations in hand forms, orientations, and movements. To tackle these obstacles, strong algorithms that can record and interpret complex hand movements in real-time must be developed.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

The objective of this study was to investigate the impact of athletes' respiratory muscle strength, as assessed through maximal inspiratory (MIP) and expiratory pressure (MEP), on aerobic endurance, as indicated by maximal oxygen consump-tion (Max VO2) kinetics. Respiratory muscle strength was assessed using a digital spirometer (Pony FX Cosmed, Italy), while maximal oxygen utilization capacity was measured using a breath-by-breath automatic portable gas analysis system (Cosmed K5, Italy). Statistical analysis was conducted utilizing SPSS 22.0. Based on the standardized regression coefficients (β), it was found that MEP (mean ± SD: 130.95 ± 42.82) and inspiratory diaphragmatic circumference values significantly influenced ventilatory equivalent (VE), oxygen consumption (VO2), and carbon dioxide pro-duction (VCO2). Conversely, the remaining predictor variables did not exhibit a sig-nificant effect on VE (mean ± SD: 134.80 ± 36.69), VO2 (mean ± SD: 3877.52 ± 868.47 ml), and VCO2 (mean ± SD: 4301.27 ± 1001.07 ml). In contrast, measurements of chest circumference (mean ± SD: 91.40 ± 10.72 cm), MEP, and diaphragmatic cir-cumference during inspiration (mean ± SD: 95.20 ± 10.21 cm) were found to signifi-cantly impact Max VO2 (mean ± SD: 58.52 ± 10.74 ml/kg/min), while the other pre-dictor variables did not demonstrate a significant effect on Max VO2. Conclusively, the study revealed that measured values of diaphragmatic circumference during inspiration and MEP exerted a notable influence on Max VO2, VE, VO2, and VCO2. Our findings underscore the importance of considering respiratory muscle strength in assessing and enhancing athletes' aerobic performance. These insights contribute to a deeper understanding of the interplay between respiratory function and exercise capacity, offering potential avenues for optimizing training regimens and perfor-mance outcomes in athletic contexts.

An HFMD outbreak spread over the city of Hải Phòng from Summer 2011 to Autumn 2012. This epidemic was chosen because it was the very first HFMD epidemic in North Vietnam, eliminating thus interferences with previous outbreaks. This epidemic displayed 3 separate waves. A complete dataset was collected for more than 9500 patients during this period, which enabled us to analyze this epidemic at different scales. Access to the healthcare system was crucial during this period, with a reorganization of the system in February-March 2012. An analysis at commune level enables us to track the epidemic along certain communication routes. The three-waves structure reveals a wide disparity at district level. We develop a mathematical model showing high accuracy at the adjustment of data for both the total number of cases and for the number of cases per week. As a consequence, the model was able to accurately determine the dates of beginning and end of each wave and to show that they overlapped. Using mathematical functions associated with this model, it was possible to calculate the probability for a patient to belong to a specific wave.

Good hand hygiene has proven to be essential in reducing the uncontrolled spread of human pathogens. Cold atmospheric plasma (CAP) may provide an alternative to disinfecting hands with ethanol-based handrubs when hand washing facilities are unavailable. CAP can be safely applied to the skin if the energy is well controlled. In this study, RF and DC plasma sources was built with a pin-to-mesh electrodes configuration inside a fused silica tube of 5 mm of inner diameter. Microbiological assays based on EN 13697:2015+A1:2019 using Escherichia coli DSM 682 or Staphylococcus epidermidis DSM 20044 were used to examine the antimicrobial effect of various plasma conditions. Metal and silicone disks that model skin were used as inoculation matrices. The prototype air radio frequency (RF) CAP achieved significant disinfection in the MHz range on stainless steel and silicone substrates. This is equivalent to half the performance of direct current CAP, which is only effective on conductive substrates. Using only electricity and air CAP could, with further optimization, replace or complement current hand disinfection methods, and mitigate the economic burden of public health crises in the future.

Bionic robotic hand can perform many movements similar to human hand. But there is still a significant gap in manipulation between robot and human hand. It is necessary to understand the finger kinematics and motion patterns of human hand to improve the performance of robotic hand. This study aimed to comprehensively investigate normal hand motion patterns by evaluating the kinematics of hand grip and release in healthy individuals. The data corresponding to rapid grip and release were collected from the dominant hand of 22 healthy people by sensory glove. The kinematics of 14 finger joints were analyzed, including the dynamic range of motion (ROM), peak velocity, joint sequence and finger sequence. The results show that the proximal interphalangeal (PIP) joint had a largest dynamic ROM than metacarpophalangeal (MCP) and distal interphalangeal (DIP) joints. Besides, the PIP joint had the highest peak velocity, both in flexion and extension. For joint sequence, the PIP joint moved prior to the DIP or MCP joints during flexion, while extension started in DIP or MCP joints, followed by PIP joint. Regarding the finger sequence, the thumb started to move before four fingers, and stopped moving after the fingers during both grip and release. This study explored the normal motion patterns in hand grip and release, which provided kinematic reference for the design of robotic hand and thus contribute to its development.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Background Sarcopenia is a state with progressive and generalized loss of skeletal muscle mass and strength. It is a serious complication occurring in chronic kidney disease (CKD) patients which increases morbidity and mortality rate. Sarcopenia is diagnosed when loss of both compartments - muscle strength and skeletal muscle quality or quantity are present. However, there are still numerous patients, also with CKD, diagnosed as pre-sarcopenic individuals with low muscle strength and normal skeletal muscle quality or quantity and conversely, with correct muscle strength and decreased skeletal muscle mass, who are prone to develop sarcopenia in future life. It is crucial to examine numerous variables possibly associated with changes of skeletal muscle mass and muscle strength in terms of preventing the development of sarcopenia. The aim of the study was to investigate anthropometric and clinical correlates and sources of variation in both skeletal muscle mass and muscle strength in advanced stages of CKD. Methods The study sample consisted of 84 non-dialysis dependent patients of both sexes (including 45.2% of women) with eGFR < 45 ml/min/1.73m²: 26.2% with eGFR 30-44 mL/min/1.73 m², 65.5% with eGFR 15-29 mL/min/1.73 m² and 8.3% with eGFR < 15 mL/min/1.73 m². Muscle strength was estimated by measuring hand grip strength (HGS) with the use of handheld hydraulic dynamometer. Muscle quantity was measured by bioimpedance spectroscopy using Body Composition Monitor. Appendicular skeletal muscle mass (ASM) was calculated according to Lin’s formula. Serum creatinine, urea, uric acid and albumin were measured. Results In bivariate analysis we found that ASM significantly and positively correlated with anthropometric variables such as body mass (r=0.903, p<0.001), NH weight (r=0.882, p<0.001), height (r=0.694, p<0.001), body mass index (BMI) (r=0.701, p<0.001), lean tissue mass (LTM) (r=0.664, p<0.001), lean tissue index (LTI) (r=0.433, p<0.001), fat mass (r=0.614, p<0.001) and fat tissue index (FTI) (r=0.449, p<0.001), and was negatively associated with clinical variable such as hydration status (p<0.001). HGS significantly and positively correlated with anthropometric parameters such as body mass (r=0.319, p=0.003), NH weight (r=0.315, p=0.004), height (r=0.666, p<0.001), LTM (r=0.490, p<0.001), LTI (r=0.238, p=0.029), and ASM (r=0.501, p<0.001), and was negatively associated with clinical variables like uric acid (p=0.039) and urea (p<0.001). After adjustment for age, sex and height, HGS remained significantly and negatively related with uric acid (β=-1.078, p=0.041) and hydration status (β=-0.805, p=0.042). Conclusions In CKD patients, ASM is determined mainly by anthropometric parameters but HGS - both by anthropometric and clinical variables specific for CKD.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Ankle sprains are the most frequently occurring musculoskeletal injuries among recreational athletes. Ankle support through bandages following the initial orthotic treatment might be beneficial for rehabilitation purposes. Since hardly any study has investigated the impact of bandages in the acute phase of ankle sprains, our study examined the immediate effects of wearing an ankle bandage on fine coordination, proprioception, and motor performance in subjects five weeks after an acute ankle injury. In total, 70 subjects with acute unilateral supination trauma were tested. All subjects completed several rating questionnaires and biomechanical investigations, including a fine coordination and proprioception test, single leg stances, the Y-Balance test and gait analysis. All biomechanical investigations were conducted for the subject's injured leg with and without a bandage (MalleoTrain® Bauerfeind AG) and the healthy leg. Subjects reported moderate to strong improvements in ankle stability and pain when wearing the bandage. Wearing the bandage significantly normalized subjects’ single leg stance performance, as well as the stance phase duration, and the vertical ground reaction forces during walking. However, the bandage did not have a clear effect on fine coordination and proprioception. Wearing a bandage in the acute phase of an ankle sprain may immediately improve motor performance, including standing and walking.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

In this proposed work, five systems were developed to classify four motor functions—forward hand movement (FW), grasp (GP), release (RL), and reverse hand movement (RV)—from EEG signals. The dataset used is WAY-EEG-GAL, involving participants performing a sequence of hand movements. During preprocessing, bandpass filtering was applied to remove artifacts and focus on the mu and beta frequency bands. The first system, a preliminary study model, explored the overall framework of EEG signal processing and classification. It utilized time-domain features like variance and frequency-domain features like alpha and beta power, with classification performed using a KNN model. Insights from this system informed the development of a baseline system, which uses the same dataset but different feature extraction and classification paradigms. This baseline system combined the common spatial patterns (CSP) method with continuous wavelet transform (CWT) for feature extraction and employed a GoogLeNet classifier with transfer learning. Classification was performed on six unique pairs of events derived from the four motor functions, using both intrasubject and intersubject methods. The baseline system achieved the highest accuracy of 99.73% for the GP-RV pair and the lowest accuracy of 80.87% for the FW-GP pair in intersubject classification. Building on this, three additional systems were developed to perform 4-way classification. Among these, the final model, ML-CSP-OVR, achieved the highest intersubject classification accuracy of 78.08% using all combined data and 76.39% for leave-one-out intersubject classification. This proposed model, which features a novel combination of CSP-OVR, CWT, and GoogLeNet, demonstrates strong potential as a general system for motor imagery (MI) tasks without being subject-dependent.

Hand gestures are an essential part of human-to-human communication and interaction, and therefore for technical applications, the aim is increasingly to achieve interaction between humans and computers that is as natural as possible, for example by means of natural language or hand gestures. In the context of human-machine interaction research, these methods are consequently being explored more and more. However, the realization of natural communication between humans and computers is a major challenge. In the field of hand gesture recognition, research approaches are being pursued that use additional hardware such as special gloves to classify gestures with high accuracy. Recently, deep learning techniques using artificial neural networks have been increasingly proposed for the problem of gesture recognition without using such tools. In this context, in our approach convolutional neural network (CNN) will be explored in detail for the task of hand gesture recognition. CNN is a deep neural network that can be used in the field of visual object processing and classification. The goal of this work is to recognize ten types of static hand gestures in front of complex backgrounds and different hand sizes based on raw images without the use of extra hardware. We achieved good results with a CNN network architecture consisting of seven layers. Through data augmentation and skin segmentation, a significant increase of the model accuracy was achieved. On public benchmarks the ten gestures have been classified almost perfectly with a testing accuracy of 96.5%

The global use of alcohol based hand sanitizers (ABHS) as a means of controlling the transmission of infectious disease increased dramatically in 2020 as governments and public health agencies across the world advocated hand hygiene as a preventative measure during the COVID-19 pandemic. Although the performance of these products is most commonly defined as a function of their alcohol concentration, they are multifaceted products in which an interplay of several factors is important in determining efficacy. The hand sanitizer tetrahedron, is a novel concept that considers both ABHS formulation factors and product performance factors from a multi-dimensional perspective. The four faces of the tetrahedron represent input/formulation factors: 1) the type and amount of alcohol, 2) inactive ingredients, 3) the type of formulation/delivery system and 4) manufacturing practices. The four corners of the tetrahedron represent output/product performance factors: 1) efficacy, 2) sensory characteristics, 3) usage, usability and compliance and 4) product safety/adverse effects. All factors are of importance to ensuring the effectiveness and utility of these products.

Classification of electromyographic signals has a wide range of applications, from clinical diagnosis of different muscular diseases to biomedical engineering, where their use as input control of prosthetic devices has become a hot topic of research. Challenge of classifying this signals relies on the accuracy of the proposed algorithm and the possibility of its implementation on hardware. This paper consider the problem of electromyography signal classification, solved with the proposed signal processing and feature extraction stages, with focus lying on the signal model and time domain characteristics for better classification accuracy. The proposal considers a simple preprocessing technique that produces signals suitable for feature extraction, and the Burg reflection coefficients to form learning and classification patterns. These coefficients yield a competitive classification rate compared to used time domain features. Sometimes, the feature extraction from electromyographic signals showed that procedure can omit less useful traits for machine learning models. Using feature selection algorithms provides a higher classification performance with as fewer traits as possible. Algorithms achieved a high classification rate up to 100% with low pattern dimensionality, with other kinds of uncorrelated attributes for hand movement identification.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Due to Motor Neurone Diseases, a large population remains disabled worldwide, negatively impacting their independence and quality of life. This typically involves a weakness in the hand and forearm muscles, making it difficult to perform fine motor tasks such as writing, buttoning a shirt, or gripping objects. This project presents a vision-enabled rehabilitation hand exoskeleton to assist disabled persons in their hand movements. The design goal was to create an accessible tool to help with a simple interface requiring no training. This prototype is built on a commercially available glove where a camera and embedded processor were integrated to help open and close the hand, using air pressure, thus grabbing an object. An accelerometer is also implemented to detect the characteristic hand gesture to release the object when desired. This passive vision-based control differs from active EMG-based designs as it does not require individualized training. Continuing the research will reduce the cost, weight, and power consumption to facilitate mass implementation.

Deep learning-based handwriting personality prediction uses neural networks (CNNs) to consider and predict personality characters from handwritten text to improve applications such as adaptive technology and automated data access. This method requires high computational resources and widely classified data, and its accuracy may suffer from signature variation and overfitting. This study introduces a novel optimizeddeep learning for Hand Written Personality Prediction. First the input data is collected from givendataset and an enhanced Gaussian filter is used in pre-processing to improve image quality by reducing noise and increasing contrast.After pre-processing, features are extracted by PCA-based normalized GIST, which standardizes the features to improve image representation.These extracted features are generated using an adaptive horse herd optimization algorithm to select the most important features. Based on selected features Improved Generative Adversarial Networks with artificial hummingbird optimization (IGAN_AHb) enables fast and efficient convergence of GANs. This reduce the mode collapse and ensures training with consistently fine-tuned parameters.The selected features are considered by characters such as openness, conscientiousness, extroversion, agreeableness and neuroticism, and finally classified using the IGAN_AHb classifier. In the result section, the proposed model is compared with various models with the matrix precision, recall, F1-score. The proposed model attained the value of 97.3% of precision and a recall rate of 96%, respectively. By comparing with other models, the proposed model attained highest values.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Water resources, especially safe, potable water, are limited for many Haitians. In areas where shallow groundwater is available, many household water needs such as laundry, bathing, and cooking are supplied by hand-dug wells. In order to better understand the water quality and prevalence of these household wells, 35 hand-dug wells were surveyed and sampled near the Hôpital Albert Schweitzer (HAS) in Deschapelles, Haiti. Water samples were collected and tested for fecal coliform and E. coli using the IDEXX Colilert-18 method. Of the samples collected, 89 percent were determined unsafe to use as a drinking water source based on the World Health Organization standard of 1.0 colony-forming unit (cfu) Escherichia Coli (E. coli) per 100 mL. 66 percent of the wells exceeded recreational/body contact standards for the state of Michigan (130 cfu/100 mL). Some of these wells were deemed suitable for conversion to a new well type called In-Situ Filtration (ISF) wells. ISF wells are installed with an internal sand filter pack, PVC casing, pump, and cap which seals the well from surface contamination and provides additional water treatment as water is pumped. Previous ISF installations have reduced E. coli to safe drinking water levels within 90 days.

This study investigates by hybrid approach of classical calculations and numerical explicit FEM simulation the strain rate sensitive hardening of Polypropylene Sabic 83MF10 under dynamic tension loads. The Cowper-Symonds model is employed to characterize the non-linear increase in yield strength with strain rate, within the range of 0,01 to 1 [1⁄s]. For lower strain rates, a drastic decrease in yield strength is observed, suggesting the significant influence of creep and relaxation phenomena. The study proposes further research incorporating viscoelastic properties for a more comprehensive material model. Additionally, the study observes a disproportionate increase in yield strength for samples with smaller radius, indicating a dependency on triaxiality which suggests further research on the Drucker-Prager model for this material. The study concludes by recommending a broader range of input parameters for future studies, including the Johnson-Cook model and comparison of tensile test results with compression test results.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

Background This study aimed to examine the acute effects of different pre-ST strategies on muscular performance and blood pressure (BP) responses in recreationally strength-trained women. Methods: Twelve overweight women with normal-to-elevated BP were recruited and performed six exper-imental protocols in a randomized order: 1) control protocol (CC) – BP assessed without exercises performed, 2) strength training (ST), 3) foam rolling warm-up followed by strength training (FR+ST), 4) specific warm-up followed by strength training (SW+ST), 5) aerobic exercise followed by strength training (AE+ST), and 6) stretching exercises followed by strength training (SE+ST). Strength training consisted of three sets at 80% of 10RM with a self-suggested rest interval between sets for bench press, back squat, bench press 45º, front squat, lat pull-down, leg press, shoulder press, and leg extension. Results: All experimental protocol had a lower total training volume, fa-tigue index, and repetitions performance in relation to ST (p

In 2011-2012, Northern Vietnam suffered its first large scale hand foot and mouth disease (HFMD) epidemic. Two sets of official guidelines were issued during the outbreak to handle the HFMD crisis. The city of Hai Phong was therefore used as a model to analyze the impact of the guidelines release. 9621 HFMD cases were reported in Hai Phong city from April 2011 to December 2012. Three distinct waves of HFMD occurred. Enterovirus A71 and Coxackievirus A16 were successively associated to the epidemics. Two periods, before and after guidelines realease, could be distinguished which were characterized by different patient patterns Time to admission and severity changed notably. Guideline publication help the health system refocusing on the 0.5-3 years age group with highest incidence of the disease. The three waves showed different special distribution but main routes of infection were rivers and local secondary roads most likely through local trade and occupational movements of people.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

Olive picking is one of the most common social agricultural activities in many regions of Andalusia where the predominant crop is the traditional olive grove. The machinery used includes shakers, blowers and an essential low-cost type: hand-rake sweepers. The latter are generally used by the women of the squads to sweep the olives that fall from the trees. This article is focused on the design and optimisation of a hand-rake sweeper, in terms of durability and cost, for the picking of olives and other fruits, such as almonds, which are currently the main alternative to non-perennial crops in Andalusia. A parametric design of a hand-rake sweeper was created for this application using the design software CATIA, and its most vulnerable points were analysed in terms of effectiveness with varying design parameters, conducting usage simulations with ANSYS for a light material such as polypropylene. The maximum von Mises stress of the whole structure was 155.81 MPa. Using ANSYS, the dimension parameters of the hand-rake sweeper structure were optimised. The modified design was analysed again, showing a reduction of maximum tensions of 10.06%, as well as a decrease in its maximum elongations (0.0181 mm).

The evolution of manual grooming and its implications have received little attention in the quest to understand the origins of simian primates and their social and technical intelligence. All simians groom manually, whereas prosimians groom orally despite comparable manual dexterity between some members of the two groups. Simians also exhibit a variable propensity for the manipulation of inanimate, non-food objects, which has culminated in tool making and tool use in some species. However, lemuriform primates also seem capable of tool use with training. Furthermore, lemuriforms appear to understand the concept of a tool and use their own body parts as “tools”, despite not using inanimate objects. This suggests that prosimian primates are pre-adapted for proprioceptive object manipulation and tool use, but do not express these cognitive abilities by default. This essay explores the paleontological, anatomical, cognitive, ethological, and neurological roots of these abilities and attempts to explain this behavioural divide between simians and prosimians. Common misconceptions about early primate evolution and captive behaviours are addressed, and chronological inconsistencies with Machiavellian Intelligence are examined. A “licking to picking” hypothesis is also proposed to explain a potential link between manual grooming and object manipulation, and to reconcile the inconsistencies of Machiavellian Intelligence. Bayesian decision theory, the evolution of the parietal cortex and enhanced proprioception, and analogies with behavioural changes resulting from artificial selection may help provide new insights into the minds of both our primate kin and ourselves.

Sialyllactose (SL) is a functional human milk oligosaccharide essential for immune support, brain development, intestinal maturation, and antiviral defense. However, despite its established health benefits, the effect of SL on exercise performance and muscle mass in mice remains unknown. Here, we aimed to investigate, for the first time, the effects of 6′-SL on muscle functions. Seven-week-old male C57BL/6J mice were administered 100 mg/kg 6′-SL for 12 weeks, after which exhaustive treadmill performance, muscle strength, and muscle phenotype were examined. The administration of 6′-SL significantly improved exhaustive treadmill performance metrics, including distance and exhaustion time. Grip strength was also increased by 6′-SL administration. Additionally, 6′-SL increased muscle mass in both the gastrocnemius (GAS) and soleus. 6′-SL administration led to an increase in the minimum Feret’s diameter and the protein expression of total myosin heavy chain in the GAS muscle. In conclusion, 6′-SL administration in vivo led to increased running distance and time by increasing muscle mass and strength. These findings collectively indicate that 6′-SL is a potential agent for improving muscle health and exercise performance.

How infants engage with objects changes dramatically over the first year of life. While some infants exhibit a consistent hand preference for acquiring objects during this period, others have no identifiable preference. The goal of this study was to test whether lateralization confers an advantage in the development of early object skills. We examined whether lateralized infants show different rates of growth in how they interact with multiple objects as compared to infants without a hand preference. In a longitudinal design consisting of seven monthly visits from 6-12 months, 303 infants were assessed for hand preference and object management skill (i.e., holding up to three objects). Group-Based Trajectory Modeling (GBTM) identified three hand preference trajectory groups: Left, Right, and No Preference (NP). A Hierarchical Generalized Linear Model (HGLM) found that Left and Right infants differed in their linear and quadratic slopes and transitioned from holding one to two objects more quickly than NP infants. While all infants showed similar trends in object management skill across time, lateralized infants had an advantage. Further work is needed to determine if this early object skill advantage cascades to later more complex object handling.

Hand gestures may play an important role in medical applications for health care of elderly people, where providing a natural interaction for different requests can be executed by making specific gestures. In this study we explored three different scenarios using a Microsoft Kinect V2 depth sensor then evaluated the effectiveness of the outcomes. The first scenario utilized the default system embedded in the Kinect V2 sensor, which depth metadata gives 11 parameters related to the tracked body with five gestures for each hand. The second scenario used joint tracking provided by Kinect depth metadata and depth threshold together to enhance hand segmentation and efficiently recognize the number of fingers extended. The third scenario used a simple convolutional neural network with joint tracking by depth metadata to recognize five categories of gestures. In this study, deaf-mute elderly people execute five different hand gestures to indicate a specific request, such as needing water, meal, toilet, help and medicine. Then, the requests were sent to the care provider’s smartphone because elderly people could not execute any activity independently. The system transferred these requests as a message through the global system for mobile communication (GSM) using a microcontroller.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

Significant progress has been made in understanding the computational and neural architecture that mediates eye and hand movements made in isolation. However, less is known about the mechanisms that control these movements when they are coordinated. Here, we outline our computational approaches using accumulation-to-threshold and race-to-threshold models to elucidate the mechanisms that initiate and inhibit these movements. We suggest that, depending on the behavioral context, the initiation and inhibition of coordinated eye-hand movements can operate in two modes- coupled and decoupled. The coupled-mode operates when the task context requires a tight coupling between the effectors; a common command initiates both effectors, and a unitary inhibitory process is responsible for stopping them. Conversely, the decoupled mode operates when the task context demands weaker coupling between the effectors; separate commands initiate the eye and hand, and separate inhibitory processes are responsible for stopping them. We hypothesize that higher-order control processes assess the behavioral context and choose the most appropriate mode. This computational architecture can explain heterogeneous results observed across many studies that have investigated the control of coordinated eye-hand movements and may also serve as a general framework to understand the control of complex multi-effector movements.

Electromyographic (EMG) signals provide information about a person's muscle activity. For hand movements, in particular, the execution of each gesture involves the activation of different combinations of the forearm muscles, which generate distinct electrical patterns. Conversely, the analysis of these muscle activation patterns, represented by EMG signals, allows recognizing which gesture is being performed. In this study, we aimed to implement an automatic identification system of hand or wrist gestures based on supervised Machine Learning (ML) techniques. We trained different computational models and determined which of these showed the best capacity to identify six hand or wrist gestures and generalize between different subjects. We used an open access database containing recordings of EMG signals from 36 subjects. Among the results obtained, we highlight the performance of the Random Forest model, with an accuracy of 95.39%, and the performance of a convolutional neural network with an accuracy of 94.77%.

Technological advancements in the Internet of Things (IoT), unmanned aerial vehicles (UAVs), and novel technological tools have transformed disaster management practices from localized approaches to a global framework. These innovations necessitate a unified understanding and application of diverse methodologies at an international level, ensuring they are accessible and operational across different sectors. This integration is crucial not only for technical personnel but also for medical teams, who play a pivotal role in disaster response and management. By fostering a comprehensive grasp of these methods, we can enhance coordination, efficiency, and effectiveness in addressing disasters on a global scale. The authors aimed to provide a comprehensive overview of emerging techniques that are driving shifts in strategic approaches and treatment technologies. Recognized as a domain of continuous research and development, this overview, by necessity, remains an incomplete snapshot of an evolving field. It highlights the dynamic nature of technological and strategic advancements, underscoring the importance of ongoing investigation and innovation to stay abreast of current trends and future directions. The article also highlights the importance of international collaboration beyond societal and national boundaries A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multijetfusion technology and polyamide 12 as a material. It reports an efficient solution for manufacturing functional prototypes and final parts for water pressure applications. It provides manufacturing rules to engineers in the pressurized product development process up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thickness for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies

In developed countries, especially the big-sized ones like Australia and the USA, a car is almost an inevitable necessity to carry out daily activities. Due to this, used cars have become a great alternative to brand new cars because of their cost effectiveness. In this work, estimation of prices of used cars based on numerous factors is studied statistically. Data is based on prices of used cars sold across Australia. Statistical methods like correlation and permutation tests using linear regression model, exact tests and non-parametric bootstrapping is implemented to study the relationship of price with mileage and year of manufacture of the car using p-values and null hypothesis. Predictions are also made on the price by calculating a 95% confidence interval (CI) of median prices in small portions of the dataset. The study presents potential ideas for understanding correlation between variables and parameters in business studies.

This research paper investigates the enhancement of strength and performance of self-compacting concrete (SCC) for integration in Department of Public Works and Highways (DPWH) projects using a value engineering approach. The study explores key elements of SCC's strength and performance, including mix design optimization, construction practices, and durability considerations. Strategies to optimize SCC's strength, durability, and workability are discussed, emphasizing the benefits of SCC in improving construction efficiency and quality control within DPW infrastructure. The study also identifies challenges and gaps in SCC utilization, such as standardized performance verification and cost considerations, and proposes future directions for advancing SCC technology in civil infrastructure development.

A biobased and conductive ink composed of elastomeric vinyl acetate-vinyl laurate copolymer (PVAc-VL) and carbon nanofibers (CNF) has been developed to create stretchable and flexible tactile devices (taxels) for robotics and prosthetics applications. The ink can be sprayed onto elastomeric surfaces (Ecoflex) to produce an electronic skin for applications such as the iCub robot and the Hannes prosthetic hand. Electron microscopy analysis confirms good dispersion of the CNF within the ink, and the ink remains conductive even after 150 mechanical cycles of stretching up to 25% and unloading. Compression tests up to 50% deformation show a small influence on the coating, and stretching cycles allow for rearrangement of the CNF, improving the electrical behaviour due to mechanical energy dissipation. The measured electrical performance exhibits a twofold increase in the R/R0 ratio, succeeded by a rapid decline (recovery), and eventually stabilizes near the initial value, indicating enhanced electronic performance.

Gesture recognition has always been a technique to decrease the distance between the physical and the digital world. In this work, we introduce an Arduino based vehicle system which no longer require manual controlling of the cars. The proposed work is achieved by utilizing the Arduino microcontroller, accelerometer, RF sender/receiver, and Bluetooth. Two main contributions are presented in this work. Firstly, we show that the car can be controlled with hand-gestures according to the movement and position of the hand. Secondly, the proposed car system is further extended to be controlled by an android based mobile application having different modes (e.g., touch buttons mode, voice recognition mode). In addition, an automatic obstacle detection system is introduced to improve the safety measurements to avoid any hazards. The proposed systems are designed at lab-scale prototype to experimentally validate the efficiency, accuracy, and affordability of the systems. We remark that the proposed systems can be implemented under real conditions at large-scale in the future that will be useful in automobiles and robotics applications.

Despite ongoing efforts, the relationship between groin strength and injury remains unclear. The challenge of accurately predicting injuries presents an opportunity for researchers to develop pre-vention strategies to reduce the occurrence of such injuries. Consequently, this issue requires further investigation to obtain insights into effective mitigation strategies. In 120 male soccer players the maximum isometric strength of the hip muscle groups was measured, and the strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. The K- Nearest Neighbour (k-NN), was used to predict the incidence of injury, while the significant predictive variables of the k-NN algorithm were fitted into a multivariate logistic regression model (LR) to analyze the likelihood of players sustaining a groin injury. The LR model determined two variables as significant predictors of groin injury. Players were less likely to sustain a groin injury by 76% for each decrease of the Adductors/Abductors isometric strength ratio in the non-dominant limb (OR = 0.238, CI 95%= [(0.098-0.572]). Players with a history of previous injury had a 67% greater risk of sustaining an injury (OR = 0.333, CI 95%= [(0.1068-1.038]). Isometric hip adductor and abductor strength im-balances of the non-dominant lower limb and a history of previous injury were risk factors for groin injury in soccer players.

Strong yet ductile alloys have long been desired for industrial applications to enhance structural reliability. This work produced two (CoCrNi)93.5Al3Ti3C0.5 medium-entropy alloys with exceptional strength-ductility combinations, via short/medium (3 min/30 min)-time annealing after hot-rolling. Three types of intergranular precipitates including MC, M23C6 carbides, and L12 phase were detected in both the samples. Noticeably, the high density of intragranular L12 precipitates were only founded in the medium-time annealed sample but not in another one. Upon inspection of deformed substructure, it was revealed that the plane slip is the dominant deformation mechanism of both the alloys. This is related to the lower stacking fault energy, higher lattice friction induced by C solute, and slip plane softening caused by intragranular dense L12 precipitates. Additionally, we noted that the stacking fault and twinning act as the mediated mechanisms in deformation of the short-time annealed alloy, while only the former in the medium-time annealed one. It is attributed to the higher energy stacking faults and the increased critical twinning stress caused by intragranular dense L12 precipitates that inhibited the twinning tendency. Our present findings provide not only a guidance for optimizing the mechanical properties of high/medium-entropy alloys, but also a fundamental understanding of deformation mechanisms.

This paper introduces a multi-class hand gesture recognition model developed to identify a set of defined hand gesture sequences in two-dimensional RGB video recordings. The work presents an action detection classifier that looks at both appearance and spatiotemporal parameters of consecutive frames. The classifier utilizes a convolutional-based network combined with a long-short-term memory unit. To leverage the need for a large-scale dataset, the model uses an available dataset to then adopt a technique known as transfer learning to fine-tune the model on the hand gestures of relevance. Validation curves performed over a batch size of 64 indicate an accuracy of 93.95% (± 0.37) with a mean Jaccard index of 0.812 (± 0.105) for 22 participants. The presented model illustrates the possibility of training a model with a small set of data (113,410 fully labelled frames). The proposed pipeline embraces a small-sized architecture that could facilitate its adoption.

The emergence of the COVID-19 pandemic has propelled the use of alcohol-based hand sanitizers to the fore as a SARS-CoV-2 control measure. To be effective these products must comply with relevant quality parameters such as alcohol concentration, methanol limits and purity. The current study was designed to determine the quality of alcohol-based hand sanitizer products in the Nairobi metropolitan area. For this purpose, 74 commercially marketed samples were collected and subjected to analysis by gas chromatography. Only three samples (4.1%) complied with the regulatory specifications for alcohol content, methanol limits and pH. Five samples (6.8%) complied with the specification for alcohol content but did not meet methanol or pH limits. A total of 44 (59.5%) samples had methanol levels that exceeded threshold limits. Eleven samples (14.9%) were found with methanol substitution (i.e., methanol, instead of ethanol or isopropanol, was the main alcohol component). The results show that users of alcohol-based hand sanitizers are being exposed to substandard and falsified products which in addition to being non-efficacious pose harm due to unacceptable levels of toxic impurities. Regular, routine post-market surveillance is needed to prevent such products from reaching the market.

In this paper, we propose two novel methods for robot-world/hand-eye calibration and provide a comparative analysis against six state-of-the-art methods. We examine the calibration problem from two alternative geometrical interpretations, called hand-eye and robot-world-hand-eye, respectively. The study analyses the effects of specifying the objective function as pose error or reprojection error minimization problem. We provide three real and three simulated datasets with rendered images as part of the study. In addition, we propose a robotic arm error modeling approach to be used along with the simulated datasets for generating a realistic response. The tests on simulated data are performed in both ideal cases and with pseudo-realistic robotic arm pose and visual noise. Our methods show significant improvement and robustness on many metrics in various scenarios compared to state-of-the-art methods.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Abstract: Nordic exercises aim to improve physical abilities and prevent injuries; However, it is not clear in what type of sports modalities to use it, so this study arises from the interest of ana-lyzing its effect in different sports modalities. Objective: To analyze Nordic exercises effects on the lower limbs, and their relationship with the explosive and absolute strength inherent to demands of different sports modalities (football, athletics, basketball, sport climbing, cycling and taekwondo). Method: quasi-experimental research, identifying 122 athletes (18±3 years old) from: football (n=24), athletics/speed (n=20), sport climbing (n=20), basketball (n=24), taekwondo (n=14) and cycling (n=20); classified into a control group CG (n=57) and an experimental group EG (n=65). Results: dominant absolute strength of the initial (12.4±0.51) and final (14.5±0.98) EG, in greater proportion in basketball (P= < 0.05); explosive strength of the initial (42.4±1.2) and final (45.8±1.5) EG, with a significant difference in all modalities between before and after (p≤0.05), except in cy-cling and taekwondo; no major changes were found in the GC. Conclusion: Nordic exercises are recommended as part of training to improve levels of explosive strength with emphasis on the modalities of football, basketball, athletics/speed and sport climbing, being applicable to increase absolute strength in basketball.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Falls at height are among the major causes of fatal accidents at work, especially in the construction sector. Maintaining balance while performing a tool with both hands generates physical efforts and mental loading that needs to be managed for workers’ safety and health. The purpose of the study is to compare perceived (dis)comfort (overall and localized), the ergonomic risk and the perceived effort through the acquired postures that subjects assumed during the execution of simple and common tasks both on a ladder and on the ground. 26 subjects were asked to perform four tasks in both conditions: top screwing, frontal screwing, object picking from the bottom forward, and object picking from the bottom sideways. Subjective and objective data were gathered for assessing subjective experience (discomfort and effort, perceived) and ergonomic risk. Results highlighted few ergonomic risk differences among “on ladder” and “on ground” tasks, while subjective data reveal significant differences in different scenarios. Main results regard knees and neck areas as the most critical ones.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

Neurodegenerative illnesses, such as Parkinson’s disease (PD), have a substantial impact on the overall well-being of those who are affected. This study investigates and contrasts the capabilities of convolutional neural networks (CNN) in detecting Parkinson’s disease (PD) by utilising hand-drawn images alongside wave and spiral images as input data. This study employs pre-trained CNN models, specifically MobileNet, ResNet50, EfficientNet-B1, and InceptionV3, to classify Parkinson’s disease (PD). The findings demonstrate that MobileNet surpasses other architectural designs, as evidenced by the F1-Score of the four classes: Spiral Normal (0.87), Spiral Parkinson (0.86), Wave Normal (0.97), and Wave Parkinson (0.97). MobileNet has also shown a remarkable accuracy of 0.92 in diagnosing Parkinson’s disease. The result demonstrates the efficacy of MobileNet in extracting features from images. The results of this study enhance the application of deep learning methods in the early detection of PD, as well as help indicate the effectiveness of patient therapy and exercise, promising better patient outcomes through timely intervention and treatment.

Human-to-human communication via the computer is mainly done using a keyboard or microphone. In the field of Virtual Reality (VR), where the most immersive experience possible is desired, the use of a keyboard contradicts this goal, while the use of a microphone is not always desirable (e.g. silent commands during task force training) or simply not possible (e.g. if the user has a hearing loss). Data gloves help to increase immersion within the VR as they correspond to our natural interaction. At the same time, they offer the possibility to accurately capture hand shapes, such as those used in non-verbal communication (e.g. thumbs up, okay gesture, ...) and in sign language. In this paper, we present a hand shape recognition system using Manus Prime X data gloves, including data acquisition, data preprocessing, and data classification to enable nonverbal communication within VR. We investigate the impact on accuracy and classification time of using an Outlier Detection and a Feature Selection approach in our data preprocessing. To obtain a more generalized approach, we also studied the impact of artificial Data Augmentation, i.e., we create new artificial data from the recorded and filtered data to augment the training dataset. With our approach, 56 different hand shapes could be distinguished with an accuracy of up to 93.28%. With a reduced number of 27 hand shapes, an accuracy of up to 95.55% could be achieved. Voting Meta-Classifier (VL2) has proven to be the most accurate, albeit slowest, classifier. A good alternative is Random Forest (RF), which was even able to achieve better accuracy values in a few cases and was generally somewhat faster. Outlier Detection has proven to be a effective approach, especially in improving classification time. Overall, we have shown that our hand shape recognition system using data gloves is suitable for communication within VR.

American Sign Language is a popular language for deaf individuals. Communication is made easier for these people through sign language. However, in a digital era like today, there is a need for these people to be able to communicate online, and even get help from technology to communicate in person with non sign language speakers. This research will present a program able to translate American sign language to plain English. This study aims to use the OpenCV library to recognize hand signals, also a trained model to identify images so that the program can then translate them to words and letters. The program uses a data set of over 2000 images which will be in this case the largest data set available. With over 90\% of accuracy it results in a basic computer program with the largest data set available that would make possible for users to communicate with a wide variety of words and expressions.

This paper presents a system developed for the assistance with a collaborative robot in hand-assisted laparoscopic surgery (HALS). The system includes a sensing glove with piezoresistive sensors which capture continuously the flexion degree of the surgeon's fingers. These data are analyzed using an algorithm that detects and recognize the selected movements. This information is sent as commands to the collaborative robot throughout the surgical operation. The bending patterns, speed and execution times of the movements are modelled in a pre-phase in which it will extract all the necessary information for later detection during the motion execution. The results obtained with 10 different volunteers show a high degree of accuracy and a low false discovery rate.

Gesture recognition technology has been quickly developed in the field of human-computer interaction. The multiple-input multiple-output (MIMO) radar has been widely adopted in gesture recognition because of its notable spatial resolution. In this work, a highly accurate MIMO radar-based hand gesture recognition algorithm with very low complexity is proposed. To make the proposed system applicable in the industry and work well even when the size of the training data is limited, we applied several low-complexity adaptive signal processing methods to extract features and reduce the noise effect. First, spectrum analysis is applied to range-Doppler maps (RDMs) and a cell-averaging constant false alarm rate (CA-CFAR) with mirror filters is applied to improve the robustness to noise. Afterward, the features related to the distance, speed, direction, and the elevation angle of the moving object are determined by the proposed adaptive signal analysis techniques and the random forest is applied for classification. The proposed system has the capability to precisely distinguish and identify eight motions, including waving, moving to the left or right, patting, pushing, pulling, and rotating clockwise or anticlockwise, with an accuracy of 95%. Experiments demonstrate the capability of the proposed hand gesture recognition system to classify different movements precisely.

Vein segmentation and projection correction constitute the core algorithms of auxiliary venipuncture device, responding to the accurate venous positioning to assist puncture and reduce the number of punctures and pain of patients. This paper proposes an improved U-Net for segmenting vein and a coaxial correction for image alignment in the self-build vein projection system. The proposed U-Net is embedded by Gabor convolution kernels in the shallow layers to enhance segmentation accuracy. Additionally, to mitigate the semantic information loss caused by channel reduction, the network model is lightweighted by the mean of replacing conventional convolutions with inverted residual blocks. During the visualization process, a method that combining coaxial correction and homography matrix is proposed to address the non-planarity of the dorsal hand in this paper. First, use a hot mirror to adjust the light paths of both projector and camera to be coaxial, and then align the projected image with dorsal hand using a homography matrix. Using this approach, the device requires only a single calibration before use. With the implementation of the improved segmentation method, an accuracy rate of 95.12% is achieved by the dataset. The intersection over union ratio between the segmented and original images is reached at 90.07%. The entire segmentation process is completed in a 0.09 second, and the largest distance error of vein projection onto dorsal hand is 0.53mm. Experiments show that the device has reached practical accuracy and has the value of research and application.

This study investigated the relationship between wrist flexion and the dynamics of the swing of a croquet mallet. Twenty seven subjects participated in a study which used 3D motion capture equipment and high speed and high-definition video to determine if there is a correlation between the lateral twist of a croquet player’s swing and the flexion of the wrist during that swing. The study found a significant correlation between the amount of flexion of the wrist from the start of the stroke to the top of the backswing and the twist of the mallet head at the top of the backswing (r=0.330, p<0.01). The methodology and findings are relevant to all sports where minimising wrist flexion is favourable for improving consistency of stroke making. Additionally, reducing wrist motion in stroke-making may reduce the incidence of wrist pain and injury in croquet, further supporting recommendations to reduce the amount of wrist flexion during the croquet swing.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Enteroviruses are members of Pichornaviridae family consisting of human enterovirus group A, B, C, and D as well as nonhuman enteroviruses. Human enterovirus type 71 (EV71) has emerged as a major cause of viral encephalitis Hand, foot, and mouth disease (HFMD) in children worldwide especially in the Asia‐Pacific region. EV71 and coxsackievirus A16 are two viruses responsible for HFMD which are members of group A enterovirus. The identified EV71 receptors provide useful information for understanding viral replication and tissue tropism. Host factors interact with the internal ribosome entry site (IRES) of EV71 to regulate viral translation. However, the specific molecular features of the EV71 genome that determine virulence remain unclear. Although an EV71 vaccine has been currently approved, there is no effective therapy for treating EV71 infected patients. Therefore, understanding the host-pathogen interaction could provide the knowledge in viral pathogenesis and further benefit in the anti-viral therapy development. The aim of this study was to investigate the latest findings about the interaction of viral ligands to the host receptor as well as the activation of immune related signalling pathways for the activation of innate immunity and involvement of different cytokines and chemokines in the host pathogen interaction of EV71 along with interaction of viral proteins, mainly 2A and 3C protease, and Interferons production/signaling pathway and their inhibitory effects.

Abstract: Physicians, physical therapists, and occupational therapists have traditionally assessed hand motor function in hemiplegic patients but often struggle to evaluate complex hand move-ments. To address this issue, in 2019, we developed Fahrenheit, a device and algorithm that uses infrared camera image processing to estimate hand paralysis. However, due to Fahrenheit's de-pendency on specialized equipment, we conceived a simpler solution: developing a smartphone app that integrates MediaPipe. The objective of this study was to measure hand movements in stroke patients using both MediaPipe and Fahrenheit and to assess their criterion-related validity. The analysis revealed moderate-to-high correlations between the two methods. Consistent results were also observed in the peak angle and velocity comparisons across severity stages. Because Fahrenheit determines finger recovery status based on these measures, it has the potential to transfer this function to MediaPipe. This study highlighted the potential use of MediaPipe in pa-ralysis estimation applications.

Objectives: Evaluate hand-held echocardiography (HHE) performed and interpreted by trained Advanced Practice Providers (APPs) on hospitalized CHF patients for image quality and interpretation, by comparing against expert echocardiographer and SE findings. Background: Congestive heart failure (CHF) is associated with increased hospital admissions and mortality. While standard echocardiogram (SE) is the gold standard for cardiac assessment, it is not readily available. Hospitalized CHF patients require rapid assessment for expedited treatment. Methods: Over 6 months, five trained APPs performed HHE on hospitalized CHF patients and interpreted: a) Left ventricular (LV) size, b) LV ejection fraction (LVEF), and c) right atrial pressure (RAP). The study echocardiographer reviewed and blindly interpreted HHE images and compared with APPs and SE findings. Kappa-statistics determined the degree of agreement between APPs and study echocardiographer interpretation of HHE images and SE. Results: 80 CHF patients [age 73±14 years, 58% males; LVEF (by SE) 45±19%; 36.3% body mass indexes ≥30 kg/m2] were enrolled. HHE interpretation by APPs had good agreement for LVEF (kappa 0.79) with study echocardiographer and SE (kappa 0.74), and good agreement for RAP (kappa 0.67) with study echocardiographer. Correlation between absolute LVEF interpretation by study echocardiographer on HHE and SE was r=0.88 (p<0.0001). Conclusions: Trained APPs obtained diagnostic-quality HHE images and interpreted LV function and RAP in CHF patients, with good agreement with the study echocardiographer. LVEF by HHE correlated with LVEF by SE. Our study suggests trained APPs can use HHE to evaluate LVEF and RAP in CHF patients leading to expedited and optimized treatment.

For technical or medical applications, the knowledge of the exact kinematics of the human hand is key to utilizing its capability to handle and manipulate objects and to communicate with other humans or machines. The optimal relationship between the number of measurement parameters, measurement accuracy as well as complexity, usability and cost of the measuring systems is hard to find. Biomechanic assumptions, the concepts of a biomechatronic system and the mechatronic design process as well as commercially available components are used to develop a sensorized glove. The proposed wearable can measure 14 of 15 angular values of a simplified hand model introduced in this paper. Additionally, five contact pressure values at the fingertips and inertial data of the whole hand with a degree of freedom of six are gathered. Due to the modular design and a hand size examination based on anthropometric parameters, the concept of the wearable is applicable for a large variety of hand sizes and adaptable to different use cases. Validations show a combined root-mean-square error of 0.99° to 2.38° for the measurement of all joint angles at one finger, surpassing the human perception threshold and the current state of the art in science and technology for comparable systems.

Duchenne muscular dystrophy (DMD) is the most prevalent progressive muscular dystrophy, and the guidelines recommend the regular assessment of respiratory muscle function. This study aimed to assess the relationship between maximum inspiratory pressure (MIP), maximum expiratory pressure (MEP) and sniff nasal inspiratory pressure (SNIP) measurements and upright-supine spirometry parameters in children with DMD, predictability of upright-supine spirometry in terms of diaphragm involvement, and impact of nutrition on muscle strength. This prospective cross-sectional study examined patients with DMD by comparing upright and supine FVC, MIP, MEP, and SNIP measurements. Forty-four patients were included in the study. The mean patient age was 10.8±2.9 years. Twenty-five patients were ambulatory. A significant decrease in FVC, FEV1, and FEF25-75 values was detected in the supine position in both ambulatory and nonambulatory patients (p&lt;0.05). All patients had low MIP, MEP, and SNIP measurements (less than 60 cm H2O). MIP, MEP, and SNIP values were significantly lower in patients with malnutrition than in those without (p&lt;0.05). To accurately assess respiratory muscle strength, supine FVC should be combined with upright FVC, MIP, MEP, and SNIP measurements. It is crucial to regularly screen patients for malnutrition, as this can significantly affect respiratory muscle function during pulmonology follow-up.

This study checked whether vitamin D (Vit-D) supplementation improves the efficacy of resistance training (RT) in terms of increasing muscle strength and lean body mass (LBM) and influencing cardiorespiratory fitness (VO2max) in Vit-D insufficient middle-aged healthy men. Participants (n = 28) were quasi‐randomly assigned to one of the two groups, which, in a double‐blind manner, supplemented their diet daily with either Vit‐D (8000 IU; VD) or placebo (PLC) during participation in a 12‐week supervised RT program. During the intervention, serum Vit‐D concentrations increased 2.6‐fold (p < 0.001) in the VD group, while no changes occurred in the PLC group. Muscle strength gains (p < 0.001) as measured in seven exercises performed on RT equipment and increases (p < 0.001) in LBM were similar in the two groups. Total fat mass, percent total fat, and percent android fat decreased (p < 0.05) to a similar extent in both groups, but there was no change in VO2max in either group. In conclusion, in healthy Vit‐D insufficient middle-aged men engaged in resistance training, Vit‐D supplementation increases serum 25(OH)D levels but does not enhance gains in muscle strength and LBM or decreases in fat mass and fat percentage and does not affect cardiorespiratory fitness.

The cognitive and affective impacts of video games are subjects of ongoing debate, with recent research recognizing their potential benefits. This study employs the Gaming Skill Questionnaire (GSQ) to evaluate participants' gaming skills across six genres and overall proficiency. Eighty-eight individuals aged 20-40 participated, completed assessments of empathy and six cognitive abilities: verbal short-term memory, verbal working memory, visuospatial short-term memory, visuospatial working memory, psychomotor speed (hand-eye coordination), and attention. Cognitive abilities were examined using the Digit Span Test, Corsi Block Test, and Deary-Liewald Reaction Time Task, while empathy was assessed using the Empathy Quotient Questionnaire. Findings indicate that high video game skill levels correlate with improvements in visuospatial short-term and working memory, psychomotor speed, and attention. Different genres enhanced specific skills: RPGs positively influenced verbal working and visuospatial short-term memory but negatively affected empathy; action games improved psychomotor speed and attention; and puzzle games benefited visuospatial working memory. These promising results contribute positively to ongoing research on the cognitive and affective effects of video games, highlighting the potential for video games to enhance certain cognitive functions while also underscoring the complexity of their impact on empathy. Future research should further investigate genre-specific effects and long-term outcomes.

Background: For the treatment of bone defects, biodegradable compressive biomaterials are needed as a substitute, which degrade at the same rate as the bone regenerates. In this study, the compressive strength of CPC ceramics (with a layer thickness of more than 12 layers) should be compared with sintered ceramics. Methods: Round scaffolds with 20, 25, 30 and 45 layers were 3D printed the 3D Bioplotter, solidified in a water-saturated atmosphere for 3 days and then tested for compressive strength together with a sintered ceramic using a Zwick universal testing machine. Results: The 3D printed scaffolds are more compressive at 41.56 ± 7.12 MPa than the sintered ceramic at 24.16 ± 4.44. Conclusions: The round geometry sintered ceramics approach or exceed the upper limit of the compressive strength of cancellous bone in the direction of compacta (depending on the author).

The study aimed to estimate the prevalence and correlates of oral hygiene (OH) and hand hygiene (HH) behaviour among school adolescents in three Caribbean countries. In all, 7,476 school adolescents (median age 14 years), from Dominican Republic, Suriname and Trinidad and Tobago responded the cross-sectional “Global School-based Student Health Survey” (GSHS) in 2016-2017. The prevalence poor OH (tooth brushing <2 times/day) was 16.9%, poor HH (not always before meals) was 68.2%, poor HH (not always after toilet) was 28.4% and poor HH (not always with soap) was 52.7%. In adjusted logistic regression analysis, current cannabis use, inadequate fruit and vegetable intake, poor mental health and low parental support increased the odds for poor OH. Rarely or sometimes experiencing hunger, trouble from alcohol use, inadequate fruit and vegetable intake, poor mental health, and low parental support were associated with poor HH (before meals, and/or after toilet, and/or with soap). The survey showed poor OH and HH behaviour practices. Several sociodemographic factors, health risk behaviours, poor mental health and low parental support were found associated with poor OH and/or HH behaviour that can assist with tailoring OH and HH health promotion.