The present article is dealing with the state of question about building-energy monitoring systems used for data collection to estimate the Heat Lost Coefficient (HLC) with existing methods and so determinate buildings’ Envelope Energy Performance (EEP). In addition, the data requirements of HLC estimation methods are related with commonly used methods for fault detection, calibration and supervision of energy monitoring systems in buildings. Based on an extended review of experimental tests since 1978, a qualitative and quantitative analysis of Monitoring and Controlling System (MCS) specifications has been carried out. Although most actual Buildings Automation Systems (BAS) may measure the required parameters, further research is still needed to ensure that these data are accurate enough to rigorously apply the HLC estimation methods.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

A field experiment was conducted for determination of crop coefficient (KC) and water stress coefficient (Ks) for wheat crop under different salinity levels, during 2015-16. Complete randomized block design of five treatments were considered, i.e., 0.51 dS/m (fresh water) as a control treatment and other four saline water treatments (4, 6, 8 and 10 dS/m), for S1, S2, S3 and S4 with three replications. The results revealed that the water consumed by plants during the different crop growth stages follows the order of FW>S1>S2>S3>S4 salinity levels. According to the obtained results, the calculated values of crop coefficients significantly differed from those suggested by FAO No.56 for the crops. The Ks values clearly differ from one stage to another because the salt stress causes both osmotic stress, due to a decrease in the soil water potential, and ionic stress which the average values of water stress coefficient (Ks) follows this order; FW(1.0)=S1(1.0)>S2(1.0)>S3(0.93)>S4(0.82). Overall, it was found the differences are attributed primarily to specific cultivar, the changes in local climatic conditions and seasonal differences in crop growth patterns. Thus, further studies are essential to determine the crop coefficient values under different variables, to make the best management practice (BMP) in agriculture.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The lexical analysis of seminal policy-to-diplomacy documents from the socio-environmental discourse of the last fifty year agendas allowed examining the evolution of five themes: resources/waste, pollution, social and economic development, justice, and health. Contextual affinities were strongest between resources, pollution, and health and are linked to societal trends and pressures. On those grounds, the central role of resource stewardship according to nature’s physical limits is highlighted, and dedicated concepts, analytical frameworks, and methodologies with different degrees of sustainability are analyzed. To reframe the identified social and economic problems, the work proposes criteria and choices that (1) allow to compare the dynamics of socioecological states across the planet, (2) help matching the pace of socioecological change by addressing path dependencies through participation and engagement of communities, and (3) enable stakeholders to make trade-offs and take decisions in specific social, economic, political, and cultural contexts. The prioritization of resource justice and responsibility becomes a societal project : from Wellfare State to commonfare communities.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Clustering coefficient measures are key complex network analysis tools. We examine local and global clustering coefficient measures with respect to the lexicographic graph product. As a preliminary condition, we analyze the $K_3$ subgraph structure focused on vertex inclusion with respect to the product graph. From this structure, we determine both the clustering coefficient for the product graph vertices and the average clustering coefficient for the product graph.

The main goal of this paper is to show that Bayesian optimization could be regarded as a general framework for the data driven modelling and solution of problems arising in water distribution systems. Hydraulic simulation, both scenario based, and Monte Carlo is a key tool in modelling in water distribution systems. The related optimization problems fall in a simulation/optimization framework in which objectives and constraints are often black-box. Bayesian Optimization (BO) is characterized by a surrogate model, usually a Gaussian process, but also a random forest and increasingly neural networks and an acquisition function which drives the search for new evaluation points. These modelling options make BO nonparametric, robust, flexible and sample efficient particularly suitable for simulation/optimization problems. A defining characteristic of BO is its versatility and flexibility, given for instance by different probabilistic models, in particular different kernels, different acquisition functions. These characteristics of the Bayesian optimization approach are exemplified by the two problems: cost/energy optimization in pump scheduling and optimal sensor placement for early detection on contaminant intrusion. Different surrogate models have been used both in explicit and implicit control schemes. Showing that BO can drive the process of learning control rules directly from operational data. BO can also be extended to multi-objective optimization. Two algorithms have been proposed for multi-objective detection problem using two different acquisition functions.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This algorithm is designed to perform Discrete Fourier Transforms (DFT) to convert temporal data into spectral data. This algorithm obtains the Fourier Transforms by studying the Coefficient of Determination of a series of artificial sinusoidal functions with the temporal data, and normalizing the variance data into a high-resolution spectral representation of the time-domain data with a finite sampling rate. What is especially beneficial about this DFT algorithm is that it can produce spectral data at any user-defined resolution.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

Land’s basic metric is soil organic carbon (SOC) yet global estimates range 1,417–15,000 Gt C. Erosion of ancient topsoil and loss of soil taxa are most urgent of all context-triage concerns, and most ignored. Re-evaluation of topographical terrain on a non-flat Earth increases most soil dynamic inventories. Carbon credits of our neglected and disappearing SOC stocks are enumerated for mineral soils (~4,100 Gt C plus ca. 20–30% glomalin), Permafrost (>4,200 Gt C), peat (1,123 Gt C), plant roots (916 Gt C), litter (600 Gt C), microbes (200 Gt C), fungi (30 Gt C), biocrust (10–20 Gt C), earthworms (2.3–3.6 Gt C), termites (0.15 Gt C), nematodes (0.06 Gt C), ants (0.024 Gt C), and soil viruses (0.02–4.0 Gt C). Net contribution to atmospheric CO₂ is more from biotic topsoil loss (>10 Gt C/yr) than fossil fuels (<10 Gt C/yr). Although higher CO₂ results in a terrestrial greening effect with Net Primary Productivity (NPP) now ~220 Gt C/yr (cf. ~20 Gt C/yr Ocean NPP), this is arguably offset by topsoil erosion, desert expansion, plus fire at net ~16–20 Gt C/yr lost due, in part, to extravagant meat-eating with unsupportable, humus-depleting farm management. In particular, excess synthetic Nitrogen acidifies topsoil and destroys the natural SOC biota. Review shows critical topsoil loss up to 20,000 tonnes per second and, when soil microbes/invertebrates are properly considered, extinctions as high as 23 taxa per second. Sustainable Development Goals (SDGs) fail without solid soil foundation. Rather, heritage farm-data points to resolution in organic husbandry. Remedy via natural vermi-compost, 100% organic farming and practical Permaculture is under a simple premise that the Problem (i.e., SOC loss) is the Solution (viz., SOC restoration).

The paper analyses the unused urban spaces in concert with the creative city idea. The research issues are developed as follows. 1. The unused urban places express the city's unsustainability since every urban space has the potential to become such a dead zone. 2. The concept of the creative city covers different creative activities in concert with sustainable development. 3. The unusable urban places result from a modernistic approach that neglects the cultural context, of the city's division into functional zones ignoring integral living intentions and industrial exploitation in the previous city's rims. 4. The Vilnius Sport Palace is an unused space not so much due to the lack of interest, but due to a knot of interests, which politicians cannot cut. The research raises the question of whether the problem of the VSP can be solved by using the idea of the creative city. In terms of the theoretical approach, a comparative analysis is used. Besides literature analyses, the case study is applied. Additionally, the semiotic approach is used. For this purpose, two of Greimas' traditional semiotic squares in combination with Ricoeur's idea of the interpretation's conflict are applied.

The aim of the research presented here is to assess the impact of depressive disorders on the potential of the labour markets in the countries of the European Union, with particular reference to the disparities between the 'old' and 'new' EU countries. The initial hypothesis of persistent inequalities in the system under study was verified by analysing the process of convergence in the burden of depressive disorders among people aged 20-54 that occurred in the EU-27 group of countries between 1990 and 2019. The study used data from the Global Burden of Disease Study 2019 (IHME, 2020), which examined the number of years lived with disability (YLD) due to depression in the working age population. The analysis showed that the high burden of the consequences of depressive disorders is particularly true for the highly developed economies of the EU-14. The results of the convergence assessment did not confirm the real effect of catching up over time with economies in a more favourable situation, and the inequalities observed at the beginning of the analysis period deepened..

The influence of small-scale processes at the ocean-atmosphere boundary layer such as spray and foam on the surface waves prediction is studied. Estimates of the effect of including the exact number of specific fragmentation "parachute" type in the spray on the resulting drag coefficient is shown. For the estimates, the numerical simulations within WAVEWATCH III wave model are performed. The parameterizations of wind input were tested within WAVEWATCH III wave model: default ST4 and ST6 parameterizations and the ST1 and ST6 parameterizations used together with the implemented drag coefficient parameterization. The proposed parameterization takes into account the presence of foam and spay. The obtained results are compared with the NDBC buoys data. The importance of small-scale processes for waves at hurricane winds prediction and the prospects for their inclusion in modern numerical wave models is shown.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

This document makes a comprehensive analysis of the inequality of the water market in Chile, measured by the Gini coefficient method. The situation of water rights in Chile is of particular interest because it is a completely privatized system, where rights are traded in the market and therefore water is presented as a commodity. This privatization of water in Chile occurred as part of the process of neoliberalization since the 1981 Water Code. The results of this study indicate that both the concentration and the inequality in the distribution of water rights is very high. It proposes a profound revision of applying a mercantile logic to a scarce basic resource for life such as water and exploring the importance of its role as a national good for public use.

Invasive aspergillosis (IA) represents a common form of fungal infection caused by various species of Aspergillus that most frequently affect immunocompromised patients. Typically, this disease occurs preferentially in high-risk groups including patients infected with the human immunodeficiency virus (HIV), leukemia, autoimmune diseases, and organ transplant patients undergoing medical immunosuppression. Considered the second most common cause of op-portunistic fungal infection in humans after Candida albicans, this pathogen predominantly affects the lungs, but may also spread by hematogenous route to various organs and have a heterogenous presentation. Owing to its high iodine levels, high perfusion, and enclosed capsule, the thyroid gland is considered to have a lower susceptibility to microbial invasion and it is fairly uncommon to find associated infectious nodules. In metabolic imaging, 18F-FDG-PET/CT has become increasingly useful for detecting a wide range of infectious and inflammatory diseases and is already the gold standard for certain indications. According to the literature, no studies of hypermetabolic nodular thyroid aspergillosis on 18F-FDG-PET/CT confirmed on histology have yet been reported. Here, we report the first case of a patient with a heterogeneous presentation of IA and the presence of a hypermetabolic nodule in the thyroid with a surprising result.

Background: Over 900,000 cases of COVID-19 and 23,000 deaths have been reported till 13 July in India. Preserving the limited healthcare workforce is part of the strategy against the pandemic. Mortality and morbidity data have a role in customising this strategy. At this time, there is no published study on COVID-related mortality among doctors or other healthcare workers in India. Methods: A multi-pronged search was made for all reported deaths linked with COVID-19 among doctors in India. Details of COVID-linked deaths reported by mainstream media and by multiple professional social media sources were collected, screened, verified and analysed. Violent deaths occurring in the setting of pandemic-related work were separately listed. Deaths from other diseases were excluded. Results: Among 108 COVID-linked deaths among doctors, there were four pandemic-related violent deaths including three road accidents and a suicide. Of the 104 non-violent deaths, 55.5% were below 60 years of age, while 29.6% and 21% were below the age of 50 and 40 respectively. The average age at death was 56.3 (range 22 - 96). Over half of the deaths occurred among general practitioners, while surgical specialties accounted for 27% of the mortality. The geographic distribution of deaths of doctors correlated with the reported number of COVID-19 patients in each state. The total number of COVID-related healthcare worker deaths was 136, out of which eight (5.8%) were violent, and occurred in young individuals with an average age of 27.8 years. Conclusions: The majority of the 104 COVID-related non-violent deaths among doctors (55.5%) occurred below the age of 60. The average at death was 56.6 years. The states with highest number of COVID-19 cases had greater number of doctor deaths. Violent deaths among young healthcare workers in the setting of the pandemic requires special attention.

To understand the relationship between water permeability and the pore structure of cementitious materials, literature that studied both water permeability and the pore structure are reviewed, and their correlation is studied. Although the majority of this data is for cement paste, mortar, concrete, and cemented soil are also included. Based on this study, it is established the determination coefficient between water permeability and the total pore volume is very low; however, those between water permeability and the critical, threshold, and median pore diameters, respectively, are moderate. On the other hand, the threshold pore diameter, derived based on the percolation theory, exhibits a very high determination coefficient. The calculated water permeability, using the Katz and Thompson equation, agrees with the reported water permeability quantitatively to a certain level, but is overestimated.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Research on spatio-temporal geostatistical modelling remains a critical challenge in numerous scientific and engineering disciplines. This work introduces a novel extension of the dual kriging the spatio-temporal dual kriging (ST-DK) whose drift functions with fixed and adaptive coefficients are established. The approach appears to be effective in modelling complex spatio-temporal dynamics, particularly when relevant auxiliary variables exert substantial influence on the target variable. To illustrate its performance, we compare the ST-DK model with the classical spatio-temporal regression kriging (ST-RK) method for estimating temperature and air pressure data across Thailand in 2018. Our findings demonstrate that both ST-DK and ST-RK models, when utilizing adaptive coefficients, outperform their constant coefficient counterparts. Furthermore, the ST-DK method consistently exhibits superior performance compared to the ST-RK model.

In the last few years, researchers have paid increasing attention to singing voice evaluations.In their studies, they observed changes in the vibrations of the vocal folds during the transi-tion of registers. Additionally, they also found that these changes are less visible and audiblein the case of skilled singers. In order to confirm this theory we defined a new parameter,the Passaggio Peak Coefficient (PPC), obtained from an EGG signal to analyse pitch andopen quotient jump characteristics during the transition of vocal registers among 21 femaleand male choir members with different singing skills. The Kruskal-Wallis test proved thatit is possible to distinguish vocal skills, based on the ability to smoothen transitions amongfemale singers at a 5% significance level.

While the majority of previous studies assessing pain-related variables in psychopaths used electric shocks, little is known about the effectiveness of alternative pain-inducing methods to increase emotional responses such as fear and anxiety. A small sample of healthy undergraduate men (N = 15) was recruited to assess the effectiveness of a heat stimulus to induce pain in an immediate versus delayed punishment paradigm. Although pain catastrophizing, anxiety, and threat of pain did not increase throughout the experiment, participants experienced a significant increase of fear of pain and pain intensity, indicating that the heat stimulus was effective in inducing pain. Furthermore, subjects were slower in initiating the pain stimulus during the first five trials, but no time difference was found during the 15 remaining trials. No correlation was found between psychopathic traits and pain-related variables, with the exception of inconsistent results within the Fearless Dominance factor. Findings are discussed in terms of improvement for a larger scale study involving psychopathic individuals.

Human milk fat is a concentrated source of energy and provides essential and long chain polyunsaturated fatty acids. According to previous experiments, human milk fat is partially lost during continuous enteral nutrition. However, these experiments were done over relatively short infusion times, and a complete profile of the lost fatty acids was never measured. Whether this lost happens considering longer infusion times or if some fatty acids are lost more than others remain unknown. Pooled breast milk was infused through a feeding tube by a peristaltic pump over a period of 30 minutes and 4, 12 and 24 hours at 2 ml/hour. Adsorbed fat was extracted from the tubes, and the fatty acid composition was analyzed by Gas chromatography-mass spectrometry. Total fat loss (average fatty acid loss) after 24 hours was 0.6 ± 0.1%. Short-medium chain (0.7%, p=0.15), long chain (0.6%, p=0.56) saturated (0.7%, p=0.4), monounsaturated (0.5%, p=0.15), polyunsaturated fatty (0.7%, p=0.15), linoleic (0.7%, p=0.25), and docosahexaenoic acids (0.6%, p=0.56) were not selectively adsorbed to the tube. However, very long chain fatty (0.9%, p=0.04), alpha-linolenic (1.6%, p=0.02) and arachidonic acids (1%, p=0.02) were selectively adsorbed and therefore lost in a greater proportion than other fatty acids. In all cases, the magnitude of the loss was clinically low.

The forming of large rivers are the integral consequences of the deep earth process and the surface. In contrast to the hot topics for rivers related to orogenic domains, rift-related large rivers are largely ignored especially in deep time studies. The Cenozoic East Asia margin provides very good opportunity to observe this kind of rivers. It has been believed that basin-and-swell physiography dominated the East Asia margin and impeded the forming of large rives in the early Cenozoic. In this paper, we combined provenance analysis of East China Sea Basin, where is a crucial place to trace the river evolution in East Asia margin, and regional geologic constraints to reveal drainage reorganizations. Detrital zircon U-Pb ages from the Early Eocene sediments of the East China Sea Basin are firstly reported. Our results together with literature data demonstrate that regional provenance changes occurred at the middle Eocene from one singe age peak at ~110 Ma of proximal sources to multiple age spectrum derived from far inland. Source to sink analysis indicated that the North China Block and Korea Peninsular provided the most detritus. Sedimentation and tectonic features of rift basins in the potential source areas indicated that rivers flowed into Bohai Basin and Jianghan Basin cannot provide terrigenous clasts for the lower reaches in the Eocene. Contrastingly, the dominantly fluvial sediments across the Subei-South Yellow Sea Basin suggested external river system and a bypassing region since the middle Eocene, coinciding with provenance change in ECSB. All these demonstrated that a large river (East Asia River) established in east Asia margin in the middle Eocene and flowed southwestward approximately 1500km to the sea in southern ECSB. This river might last to the middle Miocene. The deep earth processes driven by Izanagi-Pacific ridge subduction resulted in the overfilled stage of Subei-South Yellow Sea Basin and the post-rift subsidence in west depression of ECSB, and thus facilitated the initiation of the EAR. Our finding shed new light on the evolving landscape in East Asia and showed how subduction of deep earth process controlled the initiation of rift-related large rivers.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

The importance of irrigation in boosting agricultural production and productivity is widely understood. Proper planning and effective and efficient management and operation of irrigation system require crop and site-specific data. Since the last few years, Ethiopia has embarked on expansion of irrigated wheat. However, crop-specific data useful for irrigation planning and management for wheat crop is limited. The objective of this research was to determine water requirements and crop coefficients for wheat crops based on field measurements. The research was carried out at the Debre Zeit Agricultural Research Center in central Ethiopia during the dry season (Bega) of 2021/22. The crop considered for the experiment was durum wheat of the Utuba variety. Two non-weighing lysimeter units were employed to measure the water balance components. The soil moisture was monitored using gravimetric method on daily basis conducted both before and after each irrigation event at various depth intervals. The crop required a total of 115 days to fully mature. The length of the growth of initial, development, mid, and late stages were about 20, 30, 42, and 23 days, respectively. Microsoft Excel was used for the data analysis and the CropWAT8.0 model to estimate the reference evapotranspiration. Crop evapotranspiration (ETc) was determined using the water balance equation, and crop coefficients were computed from ETc and reference evapotranspiration (ETo). The results indicate that the total seasonal water requirement of the crop was 392.75mm. The growth stage-based water requirement was 40.35 mm, 82.44 mm, 238.66 mm, and 31.3 mm during the initial, development, mid, and late growing stages, respectively. For the initial, development, mid, and late stages of wheat growth, the crop coefficient was calculated to be 0.51, 0.83, 1.29, and 0.52, respectively. It was found that a fourth-degree polynomial equation fits well and explains the relationship between day of growth stage and kc of the crop. Although a one-season measurement, the results generated here could be useful for crop-specific data in scarce areas.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Let $\mathcal{\mathcal{S}}_{\cos}^{\ast}$ denote the class of normalized analytic functions $f$ in the open unit disk $\mathbb{D}$ satisfying the subordination $\dfrac{zf^{\prime}(z)}{f(z)}\prec\cos z$. In the second section of this article we find the sharp upper bounds for the initial coefficients $a_{3}$, $a_{4}$ and $a_{5}$ and the sharp upper bound for module of the Hankel determinant $|H_{2,3}(f)|$ for the functions from the class $\mathcal{S}_{\cos}^{\ast}$. The first result of the next section deals with the sharp upper bounds of the logarithmic coefficients $\gamma_{3}$ and $\gamma_{4}$ and we found in addition the sharp upper bound for $\left|H_{2,2}\left(F_{f}/2\right)\right|$. For obtaining these results we used the very useful and appropriate Lemma 2.4 of N.E. Cho et al. [Filomat 34(6) (2020), 2061--2072], and the technique for finding the maximum value of a three variable function on a closed cuboid. All the maximum found values were checked by using MAPLE\texttrademark{} computare software, and we also found the extremal functions in each cases. All of our present results are the best ones and give sharp versions of those recently published in [Hacet. J. Math. Stat. 52, 596--618, 2023].

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

Longitudinal dispersion coefficient (LDC) plays an essential role in modeling the transport of pollution and sediment in the natural rivers. As a result of transportation processes, the concentration of pollution changes along the river. Different studies have been conducted to provide simple equations for estimating LDC. In this study, Support Vector Regression (SVR), Gaussian Process Regression (GPR), M5P and Random Forest (RF) examined to predict the LDC in the natural streams. The hydraulic and geometric features of different rivers gathered for developing the mentioned models for LDC estimation and various statistical criteria were utilized to scrutinize of the models. Furthermore, the Taylor chart was used to evaluate the models and achieved results showed that among machine learning models, M5P displayed the superior performance with CC of 0.823, SI of 0.812, NS of 0.577 and WI of 0.879. As well, S-D model with CC of 0.795 SI of 0.827, NS of 0.558 and WI of 0.890 had more precise results than other empirical models. The results indicates that the developed M5P model with simple formulations was superior to other machine learning models and empirical models and therefore, it can be used as a proper tool for estimating LDC in natural rivers.

In 2020, the early Covid-19 lockdown and social distancing induced the abrupt migration of traditionally presential learning activities to online domains. This “new normal” environment affected management not only of training courses, but also educational events whose main added value consisted in providing students with an interactive experience onsite, as it is the case of inter-institutional summer schools. The following research corresponds to a case study in which our organization, a French university, had to reformulate, in less than three months, one of its traditional summer schools while trying to keep the original goals. We aimed at identifying the impact of four managerial decisions by analyzing, through qualitative and quantitative surveys, students’ perception of gained or lost value regarding four topics: a) online teaching, b) pre-recorded busines cases providers, c) online social events, and d) technical solutions. With an emphasis in both didactics (i.e., knowledge) and pedagogics (i.e., learning experience), the analysis of perceived value allowed as to learn about students’ assessment position, which revealed two main issues at stake: belonging, in relation to students’ identity and academic background, and performing, related to students’ expectations.

Cell-penetrating peptides (CPPs), a group of small peptides capable of promoting the transport of molecular cargo across the plasma membrane, have become important tools in promoting the cellular uptake of exogenously delivered macromolecules. GV1001, a peptide derived from a reverse-transcriptase subunit of telomerase (hTERT) and developed as a vaccine against various cancers, reportedly has unexpected CPP properties. Unlike typical CPPs, such as the HIV-1 TAT peptide, GV1001 enabled the cytosolic delivery of macromolecules such as proteins, DNA and siRNA via extracellular heat shock protein 90 (eHSP90) and 70 (eHSP70) complexes. The eHSP-GV1001 interaction may have biological effects in addition to its cytosolic delivery function. GV1001 was originally designed as a MHC class II-binding cancer epitope, but its CPP properties may contribute to its strong anti-cancer immune response relative to other telomerase peptide-based vaccines. Cell signaling via eHSP-GV1001 binding may lead to unexpected biological effects, such as direct anticancer or antiviral effects. In this review, we focus on the CPP effects of GV1001 bound to eHSP90 and ehsp70.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

The assessment outcomes of regional susceptibility to geological disasters can directly indicate the extent and intensity of risks within the study area, thus, providing targeted guidance for disaster management efforts. This study selects eight evaluation indicators, namely elevation, gradient, terrain relief, lithology of strata, normalized difference vegetation index, distance from the fault, distance from road, and distance from the river. The study focuses on Huize County in Yunnan Province as the research area, utilizing the certainty factor (CF) and random forest (RF) models for evaluating the susceptibility to geological disasters. The non-geological disaster points in the study area are determined using the deterministic coefficient prior model, and the deterministic coefficient values for each evaluation factor serve as the classification data for the random forest model. The optimal parameters for the random forest are selected through iterative calculations of bag error in PyCharm, while the weight of the evaluation factor is determined based on the ran-dom forest model with the optimal parameters. The results of geological disaster susceptibility zoning in Huize County are obtained by overlaying the weighted deterministic coefficients of each evaluation factor. The accuracy of the evaluation results is verified using zoning statistics and ROC curves with a test sample of 30% of the points. The results demonstrate the high accuracy of the model in evaluating the susceptibility to geological disasters in Huize County. Compared to the single deterministic coefficient model, this approach offers advantages in terms of reliability and accuracy. The evaluation results can serve as a scientific reference for related work in Huize County.

Background: Tuberculosis (TB) continues to be a serious public health threat that affects the most vulnerable population. Patients who are LTFU after TB diagnosis still represent one of the biggest challenges to TB control. Method: In this prospective observational study, we aimed to identify and analyse the risk factors associated with LTFU among TB patients who started first-line TB treatment in the Sanatorium Hospital in Luanda. Result: A total of 113 patients with TB were included between August 2018 and September 2019. Seventy-six (67.3%) patients were cured, 27 (23.9%) were LTFU, 5 (4.4%) died, 4 (3.5%) were transferred and 1 (0.9%) presented a treatment failure. After excluding those dead, transferred or who failed to treatment, we observed that severe TB at the time of diagnosis (OR 9.24, 95% CI 2.18-39.04) and food insecurity were significantly associated with LTFU (OR 5.96, 95% CI 1.66-21.41). Conclusion: The findings of our study are of enormous value to understand the reasons for the LTFU of patients with TB and can guide polices and facilitate designing measures to allow better adherence, and therefore, greater treatment success

Multiple biological pathways manifest and latent, meant for human survival, become a liability in cancer cure. With an increasing understanding of innumerable complex paths, cancer progression and development of resistance is no surprise. For the three “vasculature-immune-phenotypic” fundamental changes, hypoxia is the maestro orchestrating the whole gamut of changes (through the master manipulator - HIF-1 α), simultaneously transactivating hundreds of pro-angiogenic genes. Such a complex molecular bio-network begs the question, “Is our cancer research caught in such a tangled web that we have lost sight of the Spider?”. Hypoxia is this Spider weaving compensatory webs with every intervention/ obstruction. Anti-angiogenic (AAG) research has been conducted mainly in silos – exploring independent paths. This review conceptualizes a convergence of a multitude of research worldwide to a single theme of normalizing vasculature as a primary baseline for overcoming resistance to AAGs or their combinations.

Economic burden due to premature mortality has a negative impact not only in health system even though in the society. The aim of this study was to estimate the potential years of work tenure lost (PYWL) due to Chagas disease in Colombia from 2010-2017. National data on mortality by sex and ages between 15 and 62 dues to Chagas from 2010 to 2017. The PYWL methodology was applied to assess the impact of Chagas disease in workers who suffer from them. In total, 1,261 deaths were analyzed in the study, of which 60% corresponded to males. The loss of labor productivity caused by Chagas disease was estimated at $29 million. Overall, 48,621 PYWL were lost, and there was an average of 21 years for all subjects with Chagas. Throughout the analyzed period, PYWL increased substantially, and it is necessary to continue with early detection programs to avoid premature death in working age population.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

This study aimed to evaluate potential posttreatment changes in ADC values within the tissue surrounding the enhancing lesion, particularly in areas not exhibiting MRI characteristics of in-volvement. Additionally, the objective was to investigate the correlation between ADC values, treatment response, and survival outcomes in individuals diagnosed with gliomas. This retrospective study included a total of 49 patients that underwent either stereotactic biopsy or maximal surgical resection. Histologically confirmed as Grade III or IV gliomas, all cases adhered to the 2016 and 2021 WHO classifications, with subsequent radio-chemotherapy administered post-surgery. Patients were divided into two groups: short and long survival group. Baseline and follow-up MRI scans were obtained on a 1.5T MRI scanner. Two ROI circles were positioned near the enhancing area, one ROI in the NAWM ipsilateral to the neoplasm and another symmetrically in the contralateral hemisphere on ADC maps. At follow-up there was a significant difference in both ipsilateral and contralateral NAWM be-tween the two groups, -0.0857 (p=0.004) and -0.0607 (p=0.037), respectively. There was a weak negative correlation between survival and ADC values in ipsilateral and contralateral NAWM at the baseline with the correlation coefficient -0.328 (p=0.02) and -0.302 (p=0.04), respectively. The correlation was stronger at the follow-up. The findings indicate that ADC values in normal appearing white matter (NAWM) may function as a prognostic biomarker in patients with diffuse gliomas.

There are many problems based on solving non-autonomous differential equations of the form x¨(t)+ω2(t)x(t)=0, where x(t) represents the coordinate of a material point and ω is the angular frequency. The inverse problem involves finding the bounded coefficient ω. Continuity of the function ω(t) is not required. The trajectory x(t) is unknown, but the initial and final values of the phase variables are given. The variation principle of minimum time for the entire dynamic process allows for the determination of the optimal solution {x(t),ω(t)}. Thus, the inverse problem is an optimal control problem. No simplifying assumptions were made.

Satellite measurements are one of the main sources of data on the state of the marine environment. To obtain information about the sea brightness coefficient , it is needed to correctly carry out atmospheric correction. In the presence of dust aerosol over the Black Sea, physically incorrect values of the spectral brightness coefficient often occur, and specifically negative values in the IR region of the spectrum. The main objective of the study is to evaluate the influence of dust aerosol on the spectral dependence of sea brightness, based on analytical calculations from the transfer theory using the principle of plane-parallel layers and results of validation of AERONET-OC field and remote sensing data. The work analyzes spectral dependence of the first error eigenvector of the standard atmospheric correction in the presence of dust aerosol. As result it is given that with an absorbing aerosol, the atmospheric correction error is described by the spectral course of molecular scattering, i.e. close to

Hydrogen is a promising energy carrier, exploitable to extract energy from fossil fuels, biomasses as well as intermittent renewable energy sources and its generation from fossil fuels with CO₂ separation at the source is one of the most promising pathway for fossil fuels utilization. This work is focused on a particular configuration, called Reformer and Membrane Module (RMM), which alternates stages of Steam Reforming (SR) reaction with H2 separation stages to overcome the thermodynamic limits of the conventional SR. The configuration has numerous advantages with respect to the more studied and tested membrane reactors and has been tested on a pilot scale during a pilot-scale research project. Although the numerous modelling works appeared in the literature, the design features of the material exchanger (in the so-called RMM architecture) of different geometrical configurations have not been developed and the mass transfer correlations, capable of providing design tools useful for such membrane modules, are not available. The purpose of this work is therefore to apply a physical-mathematical model of the mass transfer, in three different geometries, considering both concentration polarization and membrane permeation, in order to: i) simulate the cited experimental results, ii) estimate the scaling-up correlations for the “material exchange modules”; iii) identify the mass transfer limiting regime in relation to the gas mass flow rate.

We present an exact expression for the upscaled dynamic dispersion coefficient (D) for one-dimensional transport by Hagen-Poiseuille flow which is the basis for modeling transport in porous media idealized as capillary tubes. The theoretical model is validated by comparing the breakthrough curves (BTCs) from a 1D advection-dispersion model with dynamic D to that from direct numerical solutions utilizing a 2D advection-diffusion model. Both Taylor dispersion theory and our new theory are good predictors of D at lower Peclet Number (Pe) regime, but gradually fail to capture most parts of BTCs as Pe increases. However, our model generally predicts the mixing and spreading of solutes better than Taylor’s theory since it covers all transport regimes from molecular diffusion, through anomalous transport, and to Taylor dispersion. The model accurately predicts D based on the early part of BTCs even at relatively high Pe regime (~62) where the Taylor’s theory fails. Furthermore, the model allows for calculation of the time scale that separates Fickian from non-Fickian transport. Therefore, our model can readily be used to calculate dispersion through short tubes of arbitrary radii such as the pore throats in a pore network model.

To avoid loss of information and incorrect ranking, this paper proposes a method for ranking generalized fuzzy numbers, which guarantees both horizontal and vertical values are important parameters affecting the final ranking score. In this method, the normalized height coefficient is introduced to evaluate the influence of the height of fuzzy numbers on the final ranking score. The higher the normalized height coefficient of a fuzzy number is, the higher its ranking. The left area and the right area are presented to calculate the impact of vertical value on the final ranking score. The left area is considered the benefit area. The right area is considered the cost area. The fuzzy number is preferred if the benefit area is larger and the cost area is smaller. The proposed method can be employed to rank both normal and non-normal fuzzy numbers without normalization or height minimization. Numerical examples and comparison with other methods highlight the feasibility and robustness of the proposed method, which can overcome the shortcomings of some existing methods and can support decision-makers to select the best alternative.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

The runoff coefficient (C) represents the relationship between the surface runoff volume and the precipitated volume. It is used in engineering projects for flood estimation methods. Although C values are tabulated and consecrated in hydrological engineering, as if they were constant, they may not correspond to the reality, because in the same catchment, they can vary according to the intensity, temporal and spatial distribution of precipitation events, humidity conditions, and ground cover. This study had the objective of analyzing extreme events of precipitation and the corresponding flows to obtain experimental runoff coefficients (C) and compare them with the tabulated values. The study was conducted in four experimental catchments in the State of São Paulo, Brazil, with different land uses and soils. The runoff coefficients (C) were obtained from the analysis of hydrograms and using a digital filter, which allowed the separation of the direct runoff, of the total flow. When analyzing flow and precipitation data in different seasons of the year, selecting events of the floods of catchments and separating the flows, we observed a variation of the flow coefficient values, different from those obtained from tables.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

Many microbes live in habitats below their optimum temperature. Retention of metabolic heat by aggregation or insulation would boost growth. Generation of excess metabolic heat may also provide benefit. A cell that makes excess metabolic heat pays the cost of production, whereas the benefit may be shared by neighbors within a zone of local heat capture. Metabolic heat as a shareable public good raises interesting questions about conflict and cooperation of heat production and capture. Metabolic heat may also be deployed as a weapon. Species with greater thermotolerance gain by raising local temperature to outcompete less thermotolerant taxa. Metabolic heat may provide defense against bacteriophage attack, by analogy with fever in vertebrates. This article outlines the theory of metabolic heat in microbial conflict and cooperation, presenting several predictions for future study.

We examine the impact of temperature (T) on the Seebeck coefficient S, i.e., the T dependence of S for the single-component molecular conductor Pd(dddt)_2] (dddt = 5,6-dihydro-1,4-dithiin-2,3-dithiolate) with a half-filled band, where the coefficient is obtained from a ratio of the thermal conductivity to the electrical conductivity. The conductor exhibits Dirac electrons with a nodal line, which shows the energy variation around the chemical potential and the density of states (DOS) with a minimum. Using a three-dimensional tight-binding (TB) model in the presence of both impurity and electron--phonon (e--p) scatterings, we study the Seebeck coefficient S_y for the molecular stacking and the most conducting direction. The impact of T on S_y exhibits a sign change, where S_y > 0 with a maximum at high temperatures and S_y < 0 with a minimum at low temperatures. The T dependence of S_y suggests that the contribution from the conduction (valence) band is dominant at low (high) temperatures.The result is examined using a spectral conductivity \sigma_y(\epsilon,T) as a function of the energy $\epsilon$ close to the chemical potential \mu. Further, the Seebeck coefficients for perpendicular directions (x and z) are examined, to show both S_x and S_z being positive and no sign change in contrast to S_y.

Water pollution is the main cause of global ecological degradation and seriously affects people's water supply. In order to respond to the water environmental protection policy and provide management departments with a basis for refining water quality, this paper used the environmental Gini coefficient (EGC) method based on four indicators such as water environmental capacity, population, land area, and gross domestic production (GDP) to represent social factors, economic factors, and environmental factors, respectively. After the optimization, for COD, the EGC based on the land area was 0.30, EGC based on population was 0.21, EGC based on environment capacity was 0.02, and the EGC based on GDP was 0.45, and the sum of EGC was 0.962. From this result, we observed that the change in the Gini coefficient of each indicator was not very big. Hence, the most significant change in the Gini coefficient was that of GDP, with a higher rate than other criteria. Then, the COD, AND, and TP discharge allocation model was constructed to obtain the total allocated discharge permit in Lushui Basin. The results found that the total discharge permit allocation of COD, AN, and TP to the Lushui basin were 51483.304 tons/year, 843.119 tons/year, and 340.926 tons/year, respectively. Based on the GIS spatial analysis technology, the distribution of unfair factors that cause pollution inequity was investigated. Finally, the reduction measures were proposed to implement environmental supervision and strengthen water environment management strictly.

The article contains the results of experimental studies for a multi-opening orifice with substitute constriction factor of β = 0.5 (m = 0.25), mounted in a DN50 hydraulic measuring flume. Flow measurements were taken for a progressing turbulent flow within Reynolds numbers (Re = 4700...19500). Based on experimental data, flow characteristics as well as discharge coefficient C characteristics were determined. Relative expanded uncertainty of determining a discharge coefficient C was estimated within the changes of volume flow qv from 0.35 dm3/s to 0.68 dm3/s. The value does not exceed 1.25% within the changes of Reynolds numbers 9800 ≤ Re ≤ 19500.

Understanding the spatially varying effects of demographic factors on the spatio-temporal variation of intestinal parasites infections is important for public health intervention and monitoring. This paper presents a hierarchical Bayesian spatially varying coefficient model to evaluate the effects demographic factors on intestinal parasites morbidities in Ghana. The modeling relied on morbidity data collected by the District Health Information Management Systems. We developed Poisson and Poisson-gamma spatially varying coefficient Models. We used the demographic factors, unsafe drinking water, unsafe toilet and unsafe liquid waste disposal as model covariates. The models were fitted using the Integrated Nested Laplace Approximations (INLA). The overall risk of intestinal parasites infection was estimated to be 10.9 per 100 people with a wide spatial variation in the district-specific posterior risk estimates. Substantial spatial variation of increasing multiplicative effects of unsafe drinking water, unsafe toilet and unsafe liquid waste disposal occurs on the variation of intestinal parasites risk. The structured residual spatial variation widely dominates the unstructured component, suggesting that the unaccounted-for risk factors are spatially continuous in nature. The study concludes that both the spatial distribution of the posterior risk and the associated exceedance probability maps are essential for monitoring and control of intestinal parasites.

The health of the landing gear retraction and extension hydraulic system may be assessed using fuzzy comprehensive evaluation (FCE), however the traditional FCE method depends solely on human assessment by specialists, which is excessively subjective. To address the issue of excessive human subjective variables in the assessment, an improved FCE model based on enhanced risk coefficient is provided, which includes four consideration indexes: failure probability, failure severity, failure detection difficulty, and failure repair difficulty. To reduce subjective human judgment errors entirely due to expert experience, the improved FCE takes into account the likelihood of failure using a statistical method, the severity of failure using a fault simulation analysis based on the LMS Imagine.Lab AMESim simulation platform, and the difficulty of fault detection and repair using the aircraft manufacturer's professional maintenance information. As part of the evaluation model, the range of health assessment values and accompanying treatment methods are included, making it easier to implement on a daily basis in aircraft maintenance. As a final step, the simulation is evaluated and the simulated faults are calculated.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

Motivated by the well-known contradiction of special relativity and the heat equation, a wave equation for temperature scalar field is presented that also resolves the old controversy of (Lorentz) transformation of temperature and entropy. After showing that the current dogma of temperature and entropy being emergent concepts is based on but a logical fallacy, it is proposed that single particles posses entropy. This principle of fundamentality of entropy is then shown to be compatible with the equipartition theorem by yielding corrections in the quantum gravity regime.

Healthy human subjects develop spontaneous CD8+ T cell responses to melanocyte antigens (MA) expressed by normal melanocytes, such as Tyrosinase, MAGE-A3, Melan/Mart-1, gp100, and NY-ESO-1. This natural autoimmunity directed against melanocytes might confer protection against the development of malignant melanoma (MM), where MA are present as overexpressed tumor-associated antigens. Consistent with this notion we report here that functional T cell reactivity to MA was found to be diminished in untreated MM patients: while 57.5% of healthy controls (n=40) exhibited high-frequency MA-specific T cell reactivity ex vivo, such was detected in only 12% of the untreated MM patients (n=24). Three lines of evidence suggest that the MA-reactive T cells present in healthy subjects undergo exhaustion once MM establishes itself. First, only the MA-specific T cell reactivity was affected in the MM patients; that to third party recall antigens was not. Second, in these patients, the residual MA-specific T cells, unlike third party antigen reactive T cells, were functionally impaired, showing a diminished per cell IFN-γ productivity. Third, successful immunotherapy with AGI-101H melanoma vaccine restored natural CD8+ T cell autoimmunity to MA in 85% of the vaccinated patients (n= 27). The role of natural T cell autoimmunity to tumor-associated MA is discussed based on discrete levels of T cell activation thresholds.

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

In China, the majority of mountainous regions are characterized by complex topography and a delicate, sensitive geological environment. Coupled with a generally underdeveloped infrastruc-ture and numerous unreasonable human engineering activities, these regions are often highly susceptible to geological disasters. Geological hazards can cause significant damage to human lives and property, impeding the development of mountainous areas. Consequently, researching the assessment of geological hazard vulnerability is crucial for disaster prevention, emergency management, and economic development in these regions. This study focuses on Xuanwei City and selects eight factors for evaluation, including elevation, gradient, slope aspect, normalized vegetation index, stratigraphic lithology, distance from faults, distance from rivers, and distance from roads. These factors are chosen based on a comprehensive analysis of the spatial and tem-poral distribution of geological hazards and disaster incubation conditions. Two paired models, the deterministic coefficient model + logistic regression model (CF+LR) and the information quan-tity model + logistic regression model (I+LR), were employed to quantitatively assess the study ar-ea. The accuracy of these models was evaluated using ROC curves and AUC values. The results indicate that: (1) The AUC values for the CF+LR and I+LR coupled models are 0.799 and 0.772, respectively, demonstrating that both models can objectively and reliably assess the vulnerability to geological hazards in the study area; (2) Based on the CF+LR model calculations, the geological hazard susceptibility of Xuanwei City can be categorized into four zones: extremely high suscepti-bility (6.09%), high susceptibility (31.08%), medium susceptibility (32.26%), and low susceptibility (30.57%); (3) The CF+LR model more accurately represents the evaluation results and offers a strong reference value.

Electroencephalography (EEG) signals provide valuable insights into various activities of the human brain, including the detection of mental stress, which is a complex physiological and psychological response. However, the challenge lies in identifying mental stress accurately while mitigating the limitations associated with a large number of EEG channels. This includes issues such as computational complexity, the risk of overfitting, and the increased setup time for electrode placement, which can be cumbersome for real-life applications. Therefore, it is crucial to develop EEG channel selection algorithms that enable the creation of a wearable device capable of assessing mental stress in real-life scenarios. This study introduces a novel channel selection method aimed at identifying highly accurate channels for detecting mental stress. Our approach, known as the Correlation Coefficient of Hjorth Parameters (CCHP), assesses the correlation between activity, mobility, and complexity in the time domain to nominate the most relevant channels. By selecting channels that exhibit high correlation with the stress task while being uncorrelated with each other, CCHP significantly reduces the number of EEG channels required, without compromising accuracy or performance. To evaluate the effectiveness of CCHP, we conducted experiments using the DEAP public dataset. Comparing our results with other recent algorithms that utilize the full set of EEG channels, CCHP achieved a superior classification accuracy of 81.56% using only eight EEG channels. Furthermore, CCHP outperformed existing channel selection methods by an impressive 8%. These findings strongly indicate that the CCHP algorithm shows great promise in the design of a wearable application for mental stress detection, utilizing a minimal number of EEG channels.

We consider the inverse function $z=g(w)$ of a (normalized) starlike function $w=f(z)$ of order $\alpha$ on the unit disk of the complex plane with $0<\alpha<1.$ Krzy{\. z}, Libera and Z\l otkiewicz obtained sharp estimates of the second and the third coefficients of $g(w)$ in their 1979 paper. Prokhorov and Szynal gave sharp estimates of the fourth coefficient of $g(w)$ as a consequence of the solution to an extremal problem in 1981. We give a straightforward proof of the estimate of the fourth coefficient of $g(w)$ together with explicit forms of the extremal functions.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

The combined heat and power system is based on the principle of "cascade utilization of thermal energy" for system integration and optimization. The rational utilization of energy, as well as the rational arrangement of energy flow and the process optimization combination of the overall system are taken into account in order to achieve multifunctional goals in the field of thermal engineering. The present paper presents a detailed assessment of combined heat and power systems from above standpoints. This article is divided into two parts “CHP based on thermo-dynamic cycles” and “CHP based on non-thermodynamic cycles”. Each part is then classified based on power subsystem energy consumption efficiency (high or low), including Rankine cycle, ORC, Stirling cycle, gas turbine, reciprocating engine, PVT and fuel cell. The present paper also helps identify the research gaps in this area and provides direction on future studies on combined heat and power systems.

Hyperspectral imaging, a rapidly evolving technique, furnishes exhaustive information on Earth's surface reflectance over an extensive spectrum of wavelengths. We have developed a more precise method for analyzing spectral data by meticulously selecting plant leaf pixels and employing a relative reference approach. This enhanced technique correlates camera pixel values with light intensity, bypassing the need for complex equations and thereby providing clearer insights into vegetation vitality. The findings of this study not only enhance the precision of hyperspectral imaging but also bolster our capability for ecological monitoring and understanding environmental health. A novel algorithm based on the red-edge slope was established to classify images, exploiting the spectral reflectance data gleaned from the hyperspectral Liquid Crystal Tunable Filter (LCTF) camera. Compared with conventional SVM and K-means algorithms, our novel algorithm demonstrated commendable performance, achieving an overall accuracy of 90% with a Kappa Coefficient of 0.86. This comparison highlights the novel algorithm's relative strength and potential for large-scale satellite and drone imagery analysis applications. The advancements facilitated by this research are instrumental in ecological assessments, conservation efforts, and resource management strategies, signaling a leap forward in the era of environmental monitoring and analysis.

The vacuum preloading method effectively strengthens the soft soil foundations with vertical drainage, which will produce a smear effect when laying sand drains. Meanwhile, the seepage of pore water and soil deformation during consolidation exhibits nonlinear characteristics. Therefore, based on Gibson's 1D large strain consolidation theory, this paper developed a more generalized large strain radical consolidation model of sand-drained soft foundations under free strain assumption. In this system, the double logarithmic compression permeability relationships for soft soils with large strain properties, the variation of the radical permeability coefficient in the smear zone, and the effect of the non-Darcy flow were all included. Then, the partial differential control equations were numerically solved by the finite difference method and validated with existing radical consolidation test results and derived analytical solutions. Finally, the influences of relevant model parameters on consolidation are discussed. The analysis shows that the greater the maximum dimensionless vacuum negative pressure P0, the faster the consolidation rate of sand-drained foundations. Meanwhile, the decrease in the negative pressure transfer coefficient k1 will result in a decreasing final settlement amount. Moreover, the consolidation rate of sand-drained foundations is slower considering the non-Darcy flow, but the final settlement is unaffected.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

The main goal of our work is the revealing of problematic issues related to estimates of the absorption coefficient of colored organic matter in the northern seas from data of the Ocean and Land Color Instrument (OLCI) on the Sentinel-3 satellites. In particular, a comparison of the OLCI standard error estimates ADG443_NN_err., relating to the measurement and retrieval of the geophysical products, with the uncertainties in the real situation of the northern seas, where the natural conditions are extremely unfavorable (first of all, frequent cloudiness, low Sun heights). We conducted a comprehensive multi-sensor study of the uncertainties using various approaches, first at all, directly comparing the data from satellite (OLCI Sentinel-3 and four other ocean color sensors) and field measurements in five sea expeditions 2016-2019, by using the different processing algorithms. Our analysis has shown that the real uncertainties of the final product are significantly higher than the calculated errors of the ADG443_NN_err., which is 100% and ~10%. The main reason for that is the unsatisfactory atmospheric correction. We present the results of the analysis of the different effecting factors (satellite sensors, processing algorithms, use of the other parameters), and formulate the tasks of future work.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.

Water stress (WS) and heat stress (HS) have a negative effect on soybean plant growth and crop productivity. During WS, soybean plants opt for survival through ion homeostasis and the conformations of proteins are disconcerted as plant cells lose water while HS leads to difficulties in flowering and fruiting. Some of these changes include oxidative stress leading to the destruction of photosynthetic apparatus, macromolecules within cells and the onset of complex signaling cascades. Changes in the physiological characteristics, proteome, and certain metabolites investigated on molecular and cellular functions were studied in two soybean cultivars exposed to different heat and water stress conditions independently and in combination. Leaf protein composition was studied using 2-DE and complemented with MALDI TOF mass spectrometry. While two cultivars displayed genetic variation in response to water and heat stress, thirty-nine proteins were significantly altered in their relative abundance in response to WS, HS and combined WS+HS in both cultivars; a majority of them involved in metabolism, response to heat and photosynthesis showing significant cross-tolerance mechanisms. Functional analysis revealing a majority of heat responsive-proteins were more abundant during HS and combined stress (WS+HS) whereas these proteins were low to WS in cultivar PI 471938 and heat shock proteins were in low abundance to water, heat and combined stresses in cultivar R95-1705. Most protein abundances were not correlated with their expression at mRNA levels in PI cultivar, however, in cultivar R 95, the expression levels of transcript follow their relative abundance in proteins. Our systems bioinformatics analyses revealed that MED37C, a probable mediator of RNA polymerase transcription II protein showed potential interacting partners in Arabidopsis and our studies signifies the marked impact of this protein in PI cultivar. Elevated activities in antioxidant enzymes indicate that the PI-371938 cultivar has the ability to restore the oxidation levels and sustain the plant during the stress. Our study hypothesizes the plant’s development of cross-stress tolerance which will help foster the ongoing ventures in genetic modifications in stress tolerance.

Hay and straw are commonly used materials in agriculture. They are organic materials and therefore flammable. This article examines the behaviour of hay and straw when exposed to radiant heat. The objective of this study is to experimentally determine the ignition temperature of hay and straw under the influence of radiant heat. The research investigates the effects of sample type (hay and straw) and sample quantity on the thermal degradation process, temperature increase within the samples, and ignition temperature of the samples as a function of time. The ignition temperature of hay was determined to be higher (407°C) compared to straw (380°C). The results did not demonstrate a significant correlation between sample type and the thermal degradation process or the ignition temperature of hay and straw.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

There is a lack of knowledge concerning the effects of ambient heat exposure on morbidity in Northern Europe. Therefore, this study aimed to evaluate the relationships of daily summer-time temperature and heatwaves with cardiorespiratory hospital admissions in the Helsinki metropolitan area, Finland. Methods: Time-series models adjusted for potential confounders such as air pollution were used to investigate the associations of daily temperature and heatwaves with cause-specific cardiorespiratory hospital admissions, during summer months of 2001-2017. Daily number of hospitalizations was obtained from the national hospital discharge register, weather information from the Finnish Meteorological Institute. Results: Increased daily temperature was associated with decreased risk of total respiratory hospital admissions and asthma. Heatwave days were associated with 20.5% (95% CI: 6.9, 35.9) increased risk of pneumonia admissions and during long or intense heatwaves also with total respiratory admissions in the oldest age group (≥ 75 years). There were also suggestive positive associations between heatwave days and admissions due to myocardial infarction and cerebrovascular diseases. In contrast, risk of arrhythmia admissions was decreased 20.8% (95% CI: 8.0, 31.8) during heatwaves. Conclusions: Heatwaves, rather than single hot days, are a health threat affecting the morbidity even in a Northern climate.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.