This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Background: Previous neuroimaging studies have identified brain regions related to respiratory motor control and perception. However, little is known about the resting-state functional connectivity (FC) associated with respiratory impairment. We aimed to determine the FC involved in mild respiratory impairment without changing the saturation of percutaneous oxygen. Methods: We obtained resting-state functional magnetic resonance imaging data from 36 healthy volunteers during normal respiration and mild respiratory impairment induced by resistive load (effort breathing). ROI-to-ROI and seed-to-voxel analyses were performed using Statistical Parametric Mapping 12 and the CONN toolbox. Results: Compared to normal respiration, effort breathing activated FCs within and between the sensory perceptive area of respiration (the postcentral gyrus, anterior insular cortex (AInsula), and anterior cingulate cortex) and visual cortex (the visual occipital, occipital pole (OP), and occipital fusiform gyrus). Graph theoretical analysis showed strong centrality in the visual cortex. A significant positive correlation was observed between the dyspnoea score (modified Borg scale) and FC between the left AInsula and right OP. Conclusions: These results suggested that the FCs within the respiratory sensory area via the network hub may be neural mechanisms underlying effort breathing and modified Borg scale scores.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Mechanical properties of cardiomyocytes from different transmural regions are heterogeneous in the left ventricular wall. The cardiomyocyte mechanical environment affects this heterogeneity because of mechano-electric feedback mechanisms. In the present study, we investigated the effects of load upon transmural differences in contraction of subendocardial (ENDO) and subepicardial (EPI) single cells isolated from the murine left ventricle. Various loads were applied to the cells using carbon fiber techniques for single myocytes. To simulate experimentally obtained results and to predict mechanisms underlying the cellular response to change in load, our mathematical models of the ENDO and EPI cells were used. Extent of the transmural gradient in the time course of contractions was independent of the loading conditions where unloaded and heavy loaded (isometric) contractions were examined, but the regional gradient of the relaxation time characteristics tended to decrease when the load decreased. Under auxotonic contractions, time to peak contraction (T_max) was significantly longer in ENDO cells than in EPI cells at low preload. An increase in preload (axial stretch) prolonged T_max in both cell types; however, the prolongation was greater in EPI cells, resulting in a decrease in transmural gradient in T_max at high preload. The [Ca²⁺]_i transient decay time constant was consistent with the greater preload dependency in T_max of EPI cells. Our modified mathematical models reproduced experimental results, suggesting that differences in cooperativity of cross bridges and calcium troponin C complex interactions between the ENDO and EPI cardiomyocytes may contribute to the different cellular responses to stretch, which may provide a decrease in transmural dispersion of cellular shortening in the intact heart.

The ongoing challenge to ensure a sustainable and affordable energy supply forces industrial companies to implement appropriate measures. These measures typically lead to an increased system complexity, which has to be addressed during operation. Whereas existing approaches from the field of supervisory and optimal control appear to be capable of mastering this issue, these are still not adopted in industry. Therefore, this work presents a procedure model for the systematic development of application-oriented operating strategies for industrial energy supply systems. The procedure model combines research approaches from the fields of sequencing control and approximate MPC to extract rule-based operating strategies. By splitting the procedure model into five phases, expert knowledge can be integrated in a target-oriented manner. Subsequently to the description, the procedure model is exemplary applied to the example of an industrial heating supply system. Throughout an optimization study, the developed operating strategy is compared to a MPC strategy as well as a baseline strategy. Whereas the conventional MPC approach is the upper bound with regard to optimality, the developed operating strategy is able to generate comparable results. Compared to the baseline strategy, a relative reduction in operating expenses of 5.4 % to 37.0 % are achieved in this specific use case.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

This study examined the impact of differences in fruit load of olive trees on the rate of stem refilling. The experiment was conducted in a commercial olive orchard over the consecutive years of 2021 and 2022, during which the biennial bearing cycle of olive trees resulted in minimal fruit production in 2021 and maximal production in 2022. The rate of stem refilling was determined by quantifying the differences in water volume traversing the apex and base of the principal branches of experimental trees using sap flow sensors. Concurrent measurements of tree water status were also conducted using psychrometers, while soil moisture content dynamics were continuously recorded. Results indicate that alternate bearing significantly influences the stem refilling process, while soil moisture availability also plays a pivotal role. Water reserves were more intensively utilized during the year of full production (“ON” year) primarily to fulfill the water demands of developing fruits. This replenishment occurred in various periods during the day, including early morning, afternoon, and night, when stomatal conductance measurements indicated stomatal closure. The study suggests a more intense replenishment of reserves during the night in "ON" year trees, irrespective of soil moisture, water vapor pressure deficit, or phenological fruit development stage.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

: The significance of heating load (HL) accurate approximation is the primary motivation of this research to distinguish the most efficient predictive model among several neural-metaheuristic models. The proposed models are through synthesizing multi-layer perceptron network (MLP) with ant lion optimization (ALO), biogeography-based optimization (BBO), dragonfly algorithm (DA), evolutionary strategy (ES), invasive weed optimization (IWO), and league champion optimization (LCA) hybrid algorithms. Each ensemble is optimized in terms of the operating population. Accordingly, the ALO-MLP, BBO-MLP, DA-MLP, ES-MLP, IWO-MLP, and LCA-MLP presented their best performance for population sizes of 350, 400, 200, 500, 50, and 300, respectively. The comparison was carried out by implementing a ranking system. Based on the obtained overall scores (OSs), the BBO (OS = 36) featured as the most capable optimization technique, followed by ALO (OS = 27) and ES (OS = 20). Due to the efficient performance of these algorithms, the corresponding MLPs can be promising substitutes for traditional methods used for HL analysis.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

This paper utilizes a life cycle assessment to evaluate the energy resources and environmental impacts of three heating systems. In the first step, life cycle assessments (LCAs) are prepared for the renewable, conventional, and combined systems. The system boundary of the LCA method is "cradle to gate," which means it includes the entire life cycle of a product or process. This includes energy supply, transport, energy generation, and operational energy use. The system scenarios were compared based on ecological and energy loads in the second step. Primary energy, resources, emissions, and environmental potentials are calculated for the system scenarios using the life cycle assessment methods CML 2016 and ReCiPe 2016. Finally, models for environmental reliability and complex decision-support tools have been developed. This work addresses two main questions: how to characterize the environmental and energy impacts of the systems under study, and what is the optimal scenario for the system? The research results show that the gas boiler system has a greater environmental impact. The most significant differences between the systems relate to the degrada-tion of abiotic fossil fuels when using a gas boiler and the process of acidification when using an electric heat pump. The results can be used to develop sustainable heating systems with reduced environmental impacts and enhanced energy efficiency.

Currently, the district heating (DH) in Poland is facing many challenges. The business model used hitherto was very simple—in most cities, heating plants produced heat, and centralized heating systems supplied the "product" at a price approved annually by the president of the Energy Regulatory Office (URE). However, recent years have brought significant changes on the market. EU regulations force the elimination of old coal-fired plants that were still built in the Polish People's Republic (PRL), moreover, high prices of CO2 emission allowances aggravate the financial situation of companies. In addition, in the heating sector, the trend observed in the power sector is becoming increasingly visible—limiting the role of large sources in favor of energy generated locally, closer to the customer. One of the biggest challenges is achieving the targets set by the EU for the share of renewable energy sources (RES) in the heating sector. The war in Ukraine and problems with the supply of coal and gas are an additional impulse to turn to RES. Thus, the development of sustainable and innovative solutions for energy production and supply at the level of urban networks is currently one of the main technical challenges. The purpose of the paper is to present the current situation and perspectives of development of district heating systems in Poland with a view to the status of district heating in the world, and some deeper insight into European conditions. The review presents energy sources with particular emphasis on renewable energy sources (RES) and their cogeneration for heat production. The examples of existing heating network solutions using renewable energy sources, based on the selected published case studies, are also discussed.

Authors evaluated the relevant literature related to the purging which is the interaction between selection and inbreeding where the population may get rid of its inbreeding load at least partially. The backroad of the relevant theory was given and the available methods were described both based on the conventional quantitative genetic approach (based on genealogy data) and based on the latest genomic methods. The different parameters necessary for signalling purging (highlighting those inbreeding coefficients which are not yet been widely known in animal and veterinary science) were presented together with the relevant results of the literature. The available statistical methods together with the softwares and R packages to calculate various inbreeding coefficients and to determine inbreeding depression and purging were provided. The main results of the different approaches obtained in laboratory ZOO and domesticated populations (lethal equivalents, ancestral inbreeding, Inbreeding-Purging Model, genomic approaches) were summarized and presented. Application possibilities and future prospective of purging was also discussed.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

The application of electrode-based microfluidic devices in biological entity often imposes a problem due to joule heating. The strong applied potentials or micro channels having narrow cross sections generate undesirable temperature inside the microfluidic channels leading to strong thermal distribution inside the micro channel. When intrinsic distribution of temperature, if not fix with threshold value, causes device damage or cell loss. In this work, we investigate the effects of temperature generated due to joules heating effects and we attempt to address the design constraints for minimizing the joule heating effects in the microfluidic device for developing effective microfluidic device. The device reliability was analyzed under different parametric constraints for various types of substrate materials (PDMS, PMMA, Polyimide and glass). We also attempt to investigate the effects of cell reliability due to strong temperature gradients generated through different applied potentials on different cell types. Furthermore, the response of the device performance due to different electrode configuration and different conductivity of the medium was also studied. Our investigation will eventually provide guidelines for microfluidic researchers to fabricate efficient electrode based microfluidic device which will ultimately help to choose a critical channel dimensions, threshold potentials, and conductivity of solutions in order to avoid device damage and cell loss.

Climate change is expected to influence cooling and heating energy demand of residential buildings and affect overall thermal comfort. Towards this end, the heating degree-day (HDD), the cooling degree-day (CDD) and the HDD+CDD were computed from an ensemble of 7 high-resolution bias-corrected simulations attained from EURO-CORDEX under RCP4.5 and RCP8.5. These three indicators were analyzed for 1971-2000 (from E-OBS) and 2011-2040 and 2041-2070, under both RCPs. Results show that the overall spatial distribution of HDD trends for the 3 time-periods points out an increase of energy demand to heat internal environments in Portugal's northern-eastern regions, most significant under RCP8.5. It is projected an increase of CDD values for both scenarios; however, statistically significant linear trends were only found for 2041-2070 under RCP4.5. The need for cooling is almost negligible for the remaining periods, though linear trend values are still considerably higher for 2041-2070 under RCP8.5. By the end of 2070, higher amplitudes for all indicators are depicted for southern Algarve and Alentejo regions, mainly under RCP8.5. For 2041-2070 the Centre and Alentejo (North and Centre) regions present major positive differences for HDD(CDD) under RCP4.5(RCP8.5), within the 5 NUTS II regions predicting higher heating(cooling) requirements for some locations.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

This paper presents a review of the electrical heating method for heavy oil recovery based on past, current, and future prospects of electrical heating. Heavy oil is one of the potential crude oil used as a link to reduce the crisis of light oil used today. The obstacle of heavy oil is a high viscosity and density in which thermal injection is a method for heavy oil recovery, but it results in economic and environmental issues. Electrical heating is one of the thermal methods by transferring heat into the reservoir. The basic process of electrical heating is to increase the mobility of the oil. Because the temperature rises, it can reduce oil viscosity and makes it easier for heavy oil to flow. The past and current developments have been carried out to fill up the gap of electrical heating projects. The future prospects must meet energy efficiency, and the excessive heat will damage formation that must be tackled in the future prospect. the works adopt several electrical heating projects and applications in the world where the works give a brief future prospect of electrical heating.

Two heating surfaces with longitudinal fins are located within the closed channel inside the housing made of thermal insulation material. The air flow inside the channel was carried out by an axial fan. The heating of the fins is established by using two positive temperature coefficient heating elements (PTC). Air flows circularly from one finned surface to another, and after reaching the required temperature, it leaves the housing. In the heating system conceived in this way, a methodology based on transient thermal irreversibility of heating sources and circular air flow has been established. Volumetric air flow and circulation time within the channel were varied. The total entropy generated does not include hydraulic irreversibility, but transient thermal irreversibility of the air and heat sources. For conducting analytical modeling, the temperature of the PTC heater was considered constant at 423K and 473K. Volumetric air flow varied in the interval from 0.00001m3s-1 to 0.00006m3s-1. The experimental determination of the transient thermal entropy was performed at a much higher air flow rate of 0.005m3s-1 inside the closed channel. Due to the continuous increase in air temperature, the temperatures of both PTC heaters increased within the examined time interval of 300s. According to experimental testing, the total transient thermal entropy of the described heating system has a minimum after 175s from the start of the circular heating of the air. The minimum of transient entropy also implies the optimal time of channel opening and exit of heated air.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

Many research work has demonstrated that taken the Combined Cooling Heating and Power system (CCHP) as the core equipment, the integrated energy system (IES) can bring obvious benefit to energy efficiency, CO2 emission reduction and operation economy in urban areas. Compared with isolated IES, integrated energy micro-grid (IEMG) which is formed by connecting multiple regions IES together, through distribution and thermal network, can further improve the reliability, flexibility, cleanliness and economy of regional energy supply. Based on the existing IES model, this paper describes the basic structure of IEMG and built a IEMG planning model. The planning based on the mixed integer linear programming, and economically construction planning scheme are calculated by using known electricity, heating and cooling loads information and the given multiple equipment selection schemes. At last, the model is validated by a case study. The results show that the application of IEMG can effectively improve the economy of regional energy supply.

The paper is focused on researching the behavior of heating companies in connection with current developments in the electricity market and flexibility in the context of market behavior. The work assesses the increase in profitability through the creation of a technical-economic model using an objective function with profit maximization. The paper objective is presented the procedure and methodology for creating a model using the basic scheme of production processes integrated into the system platform. The result of the work is a comparative analysis of modelled cases of implemented operation deployment according to a defined period and modelling modes in selected time series. The description of individual outputs demonstrates the economic advantage of using combinations of modes of combined electricity and heat production, and non-combined electricity and heat production, including the use of the heat suppression mode because of overproduction of electricity.

The main consequence of radiation damage on a Silicon-Photomultiplier (SiPM) is a significant increase in the dark current. If the SiPM is not adequately cooled, the power dissipation causes it to heat up, which in turn affects its performance based on the temperature. In order to investigate this heating effect, experiments were carried out using a KETEK SiPM glued on an Al2O3 substrate, as well as HPK SiPMs that were either glued onto an Al2O3 substrate or a flexible PCB. The assemblies were connected either directly to a temperature-controlled chuck on a probe station or through layers of materials with well-defined thermal resistance. A DC-mode LED was used to illuminate the SiPM, and the resulting SiPM current was measured to determine the steady-state temperature. This temperature depended on the power dissipated in the multiplication region of the SiPM and the thermal resistance. This information can be utilized to adjust the SiPMs working point, taking into account the effects of self-heating. Similarly, this approach can be applied to packaged SiPMs that have an unknown thermal contact to a heat sink.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

We provide a comprehensive framework for forecasting five minute load using Gaussian processes with a positive definite kernel specifically designed for load forecasts. Gaussian processes are probabilistic, enabling us to draw samples from a posterior distribution and provide rigorous uncertainty estimates to complement the point forecast, an important benefit for forecast consumers. As part of the modeling process, we discuss various methods for dimension reduction and explore their use in effectively incorporating weather data to the load forecast. We provide guidance for every step of the modeling process, from model construction through optimization and model combination. We provide results on data from the PJMISO for various periods in 2018. The process is transparent, mathematically motivated, and reproducible. The resulting model provides a probability density of five-minute forecasts for 24 hours.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

This review summarises the main numerical models of fuel droplet heating and evaporation (DHE) in combustion engines across the different scales by accessing the nano/micro, meso and macroscopic fluid elements. The phenomena of multi-physics, multi-scale and multi-phase fluid flow and heat transfer are fully investigated when the fuel droplet (dodecane) is heating and evaporated into a background gas (nitrogen) crossing the liquid-vapour (LV) interface, kinetic region (i.e., Knudsen layer) and the bulk regions of liquid and gas in terms of molecular dynamics (MD) simulations, kinetic theory modelling (i.e., direct numerical solutions of Boltzmann equations) and convectional fluid dynamics approach, respectively. The evaporation coefficient of fuel evaporating molecules and their velocity distributions at the LV interface derived from MD simulations formulate a new kinetic boundary condition (KBC). Moreover, a novel kinetic model considering the inelastic collision between fuel molecules alongside the new KBC enables us to describe the non-equilibrium gas dynamics of fuel vapour and gas mixture in Knudsen layer (KL). Heat and mass flux analysis of the fuel droplet under combustion engine conditions can be accurately assessed by implementing the inelastic collision between fuel molecules in KL and a temperature-dependent evaporation coefficient at the LV interface into DHE. The surface temperature of fuel droplet and its evaporation time, which play a significant role in resolving the ignition delay and hence the combustion phasing in engines, can also be well estimated. The multi-scale modelling of fuel DHE will make significantly potential input into the cleaner engine targeting the low-carbon emissions and enhance the capability of the existing computational fluid dynamics (CFD) solvers.

Rural clean heating project (RCHP) in China aims to increase flexibility in the rural energy system, enhance the integration of renewable energy and distributed generation, and reduce environmental impact. While RCHP-enabling routes have been studied from a technical perspective, the economic, ecological, regulatory, and policy dimensions of RCHP are yet to be analysed in depth, especially in the underdeveloped areas in China. This paper discusses RCHP in rural Gansu in a multi-dimension approach. We firstly focus on the current issues and challenges of RCHP in rural Gansu. Then the RCHP-enabling areas are briefly zoned into six typical regions based on the resource distribution in Gansu Province, and a matching framework of RCHP is recommended. Then we focus on the economics and sustainability of RCHP-enabling technologies. Based on the medium-term assessment of RCHP in the demonstration provinces, various technical schemes and routes are analysed and compared so as to be adopted in rural Gansu. In addition to technical and economic effects of those schemes, the corresponding ecology, policy, finance, and market implications are also concerned. We briefly discuss how the national regulators incentivise the implementation of RCHP in rural Gansu. Major barriers to RCHP are identified as the sustainability of technology, economy, ecology, policy, finance, and market. Subsequently, some policy solutions to overcome these barriers are proposed.

An optimal scheduling strategy for cooling, heating and power (CCHP) joint-power-supply system is proposed to improve energy utilization and minimize costs in this paper. Firstly, the mathematical model of CCHP system is established. Particle swarm optimization (PSO) is used to optimize the regularization coefficient C and the kernel parameter λ which can affect the prediction accuracy of KELM(PSO-KELM). Then PV generation and load prediction model are established by PSO-KELM. In order to jump out of local optimal solution, Cauchy variation is introduced in SFLA local update, and adaptive mutation operation is carried out on SFLA individuals. The predictions of PV generation and load power by PSO-KELM are imported into the objective function, and the microgrid dispatching model is solved by the improved SFLA algorithm. Compared with the traditional GA-KELM and KELM, PSO-KELM has faster convergence and prediction accuracy. Compared with the power supply division, the operation cost of the power grid is reduced by the proposed optimization dispatching strategy of CCHP micro-grid.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

The magnetic heating effect for the superconducting quarter-wave resonator (QWR) cavities is investigated, and the Q slopes of the superconducting cavities are measured with an increasing accelerating field. Physical phenomena for zero-temperature limit are introduced. Bardeen–Cooper–Schrieffer (BCS) resistance and Casimir force are calculated for the zero-temperature limit. The vertical test is shown for the performance test of the quarter-wave resonator (QWR) cavities. The parameters for the quarter-wave resonator (QWR) cavity are presented. The Q slopes are measured as a function of an accelerating electric field at 4.2 K. The surface resistance of the superconducting cavity increases with an increasing peak magnetic field. The magnetic defects cause the degradation for the quality factor. From the magnetic degradation, we can find the magnetic moments of the superconducting cavities. All the quarter-wave resonator (QWR) cryomodules are installed in the tunnel, and beam commissioning is performed successfully.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

Thermodynamic cycles are not only the core concepts of thermal science, but also key approaches to energy conversion and utilization. So far, power cycles and refrigeration cycles have been the only two general classes of thermodynamic cycles. While diverse types of systems have been developed to perform thermodynamic cycles, no new general classes of thermodynamic cycles have been proposed. Based on the basic principles of thermodynamics, here we propose and analyze a new general class of thermodynamic cycles named class 1 heating cycles (HC-1s). Two basic forms of HC-1s are obtained by connecting six essential thermodynamic processes in the proper order and forming a thermodynamic cycle. HC-1s present the simplest and most general approach to utilizing the temperature difference between a high-temperature heat source and a medium-temperature heat sink to achieve efficient medium-temperature heating and/or low-temperature cooling. HC-1s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in energy conservation and emission reduction.

District heating networks have become widespread due to their ability to distribute thermal energy efficiently, which leads to reduced carbon emissions and improved air quality. The characteristics of these networks vary remarkably depending on the urban layout and system amplitude. Moreover, extensive data about the energy distribution and thermal capacity of different areas are seldom available. Design, optimization and control of these systems are enabled by the availability of fast and scalable models of district heating networks. This work addresses this issue by proposing a novel method to develop a scale-free model of large-scale district heating networks. Starting from coarse data available at the main substations, a physics-based model of the system aggregated regions is developed by identifying the heat capacity and heat loss coefficients. The model validation on the network of Västerås, Sweden, shows compatibility with literature data and can therefore be exploited for system design, optimization and control-oriented applications. In particular, the possibility to estimate the heat storage potential of network regions allows new smart management strategies to be investigated.

Heating films were prepared by using poly(methyl methacrylate) and polybutadiene composites containing graphite. The heating film was prepared by casting the as-made polymer composite on PET film. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film was analyzed while applying DC voltage. The electrical conductivity and the heating temperature of the heating films depended on the size, the structure, the content and the dispersion characteristics of the graphite in the composite. The electrical resistance of the heating film was controlled to adjust the heating temperature of the film. The relationship between the physical/chemical structure and the heating characteristics of the composite film was studied by measuring the heating temperature as functions of film thickness and resistance by using an infrared thermal imaging camera. The lower the film resistance, the higher the heating temperature of the film. The surface temperature was uniform throughout the film.

Upon inbreeding, the architecture of the inbreeding load shifts as selection purges strongly deleterious recessive mutations and drift fixes many milder ones. Most small inbred populations show limited genetic variation while crosses between such populations commonly express pronounced heterosis, confirming fixation. In contrast, purging appears to be limited in that inbred populations often retain substantial inbreeding depression. In addition we have the enigma Darwin noted: purely selfing taxa are unknown. Because both purging and fixation reduce inbreeding depression and load, another mechanism must exist to sustain these. Background selection and the associations that develop among alleles in small inbred populations will shift the architecture of the load potentially creating blocks of recessive mutations linked in repulsion. This would generate pseudo-overdominance that could sustain these “PODs” and inbreeding load. Recombination and crosses between lineages could erode PODs. Crosses between populations fixed for different mutations would generate high pseudo-overdominance, enhancing heterosis and potentially POD formation. New recessive mutations arising within PODs would reinforce overdominance. PODs should generate clear genetic signatures including genomic hotspots of heterozygosity and linkage disequilibrium containing alleles at intermediate frequency generating segregating load. Results from several simulation and empirical studies match these predictions. Further simulations and comparative genomic analyses are needed to rigorously test whether PODs exist in sufficient strength and number to generate persistent inbreeding depression and load in inbred lineages.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Abstract: The paper compares and analyses the effects of correctly and excessively executed heating cycles on flame straightening, far above the limits recommended by the steel manufacturer. The paperwork emphasizes the microstructural changes induced by overheating in the flame straightening process. Flame straightening is a flame heating process of metal constructions in which very limited areas of the construction are heated to the straightening temperature with the aim of inducing geometrical changes.The flame straightening process is used in most of metallic structure manufacturing companies. In many cases, it is not possible to carry out under economic conditions of metal structures without flame straightening.

Zeolitic imidazolate frameworks (ZIFs) have potential for various gas and ion separations due to their well-defined pore structure and relatively easy fabrication process compared to other metal-organic frameworks. As a result, many reports have focused on preparing polycrystalline and continuous ZIF layers on porous supports. In this study, we investigated how humidity and chamber temperature influence the structure of a ZIF-8 layer prepared by the hydrothermal method. We controlled the chamber temperature (ranging from 50 °C to 70 °C) and relative humidity (ranging from 20 % to 100 %) using a thermos-hygrostat chamber. We found that as the chamber temperature increased, ZIF-8 preferentially grew into particles rather than forming a continuous polycrystalline layer. By measuring the temperature of the reacting solution based on chamber humidity, we discovered that the heating rate of the reacting solution varied with humidity, even at the same chamber temperature. At higher humidity, thermal energy transfer was accelerated as water vapor delivered more energy to the reacting solution. Therefore, a continuous ZIF-8 layer could be formed more easily at low humidity ranges (ranging from 20 % to 40 %), while micron ZIF-8 particles were synthesized at a high heating rate. Our findings suggest that controlling the heating rate of the reacting solution is critical to preparing a continuous ZIF-8 layer, particularly for future scale-up of ZIF-8 membranes.

This paper proposes and demonstrates, in full scale, a novel type of energy geostructure (“the Climate Road”) that combines a ground source heat pump (GSHP) with a sustainable urban drainage system (SUDS) by utilizing the gravel roadbed simultaneously as energy source and rainwater retarding basin. The Climate Road measures 50m x 8m x 1m (length, width, depth) and has 800 m of geothermal piping embedded in the roadbed, serving as the heat collector for a GSHP that supplies a nearby kindergarten with domestic hot water and space heating. Model analysis of operational data from 2018-2021 indicates sustainable annual heat production levels around 0.6 MWh per meter road, with a COP of 2.9-3.1. The continued infiltration of rainwater to the roadbed increases the amount of extractable heat by an estimated 17% compared to the case of zero infiltration. Using the developed model for scenario analysis we find that draining rainwater from three single family houses and storing 30% of the annual heating consumption in the roadbed, increases the predicted extractable energy by 56% compared to zero infiltration with no seasonal energy storage. The Climate Road is capable of supplying three single family houses with heating, cooling and rainwater management year-round.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

The Casimir–Lifshitz friction force and the heating rates of two metal plates with a narrow vacuum gap between them during nonrelativistic motion of one of them are calculated analytically and numerically within the framework of fluctuation electrodynamics. Changes in material properties are taken into account using the Bloch-Grüneisen and modified Bloch-Grüneisen (with finite residual resistance) resistivity models within the Drude approximation. It is shown that identical plates with the same initial temperature have the same heating rate, determined by the power of the friction force, and the possibility of measuring the friction force from the heating kinetics of nonmagnetic metal plates with temperatures of 1–10 K is substantiated.

The paper presents an extensometer designed to measure two mechanical strains at the same time—one from tensile load and the other from torsion load. Strain transducers provide different electric signals, which, after calibration, lead to the simultaneous measurement of linear (ε) and angular (γ) strains. Each of these two signals depends on the measured process and is not influenced by the other strain process. This extensometer is designed to be easily mounted on the sample with only two mounting points and can be used to measure the combined cyclical fatigue of tensile and torsional loadings. This extensometer has two bars—one rigid, reported at the resulting stress points, and one elastic and deformable. The elastic deformable bar has two beams with different orientations. When the sample is deformed, both beams are loaded by two bending moments (perpendicular to each other and both perpendicular on the longitudinal axis of the bars).

The rapid development of electric vehicles, unmanned aerial vehicles, and wearable electronic devices has led to a high interest in research related to the synthesis of graphene with a high specific surface area for energy applications. However, the problem of graphene synthesis scalability, as well as the lengthy duration and high energy intensity of the activation processes of carbon materials, are significant disadvantages. In this study, a reactor was developed for the green, simple, and scalable electrochemical synthesis of graphene oxide with a low oxygen content of 14.1 %. The resulting material was activated using a fast joule heating method. The processing of mildly oxidized graphene with a high–energy short electrical pulse (32 ms) made it possible to obtain a graphene–based porous carbon material with a specific surface area of up to 1984.5 m2/g. The low energy intensity, simplicity, and use of environmentally friendly chemicals render the proposed method scalable.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

The ever-growing repertoire of genomic techniques continues to expand our understanding of true diversity and richness of prokaryotic genomes. Riboproteogenomics laid the foundation for dynamic studies of previously overlooked genomic elements. Most strikingly, bacterial genomes were revealed to harbour robust repertoires of small open reading frames (sORFs) encoding a diverse and broadly expressed range of small proteins, or sORF-encoded polypeptides (SEPs). In recent years, continuous efforts led to great improvements in annotation and characterization of such proteins, yet many challenges remain to fully understand the pervasive nature of small proteins and their impact on bacterial biology. In this work we review recent developments in the dynamic field of bacterial genome reannotation, catalogue important biological roles carried out by small proteins and identify challenges obstructing the way to full understanding of these elusive proteins.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

Nutrition and calorie intake are associated with subtle changes of thyroid function tests in subjects with intact Hypothalamic-Pituitary-Thyroid axis. Iodine deficiency and extreme fluctuations in calorie intake, such as those occurring during periods of starvation or overfeeding could lead to alterations of thyroid hormones. The dietary macronutrient composition could also influence the thyroid function. Recently, Low-Glycemic Load (LGL) diets are very popular and effective in the treatment and/or prevention of several medical conditions, including diabetes, obesity, cardiovascular disease, and epilepsy. In this review, we report the available data from the literature regarding the association between LGL diets and thyroid function or dysfunction. Unfortunately, there are only a few studies in this field, with inconsistent findings.

Abstract: Considering the significance of postural balance in shooting ability, and consequently soldiers’ occupational performance and survivability, it is of importance to promote the use of balance training programs to improve shooters' efficiency. This study explored how a balance training program affects shooting performance. Twenty participants were divided into two equal groups. They all performed 60 shots in a shooting simulator while standing. The participants went through this process twice, before and after a 4-week balance training program. The shoot-ing was done under four different conditions: without load on a stable surface, with load on a stable surface, without load on an unstable surface, and with load on an unstable surface. The training program had a significant impact on the experimental group, improving their balance by 76 ± 9% (p < 0.01). Additionally, in the experimental group, shooting score increased by 47% and the % center of gravity by 20% (p < 0.01). The stability of the shots, measured by holding time in the target, doubled from 2.2 to 4.5 seconds (p < 0.01). These improvements were more pronounced when participants had a load and/or were on an unstable surface. In conclusion, a balance training program can be beneficial for improving shooting performance.

Hazelnut, pistachio and cashew are tree nuts with health benefits but also with allergenic properties being prevalent food allergens in Europe. The allergic characteristics of these tree nuts after processing combining heat, pressure and enzymatic digestion were analyzed through in vitro (Western blot and ELISA) and in vivo test (Prick-Prick). In the analyzed population, the patients sensitized to Cor a 8 (nsLTP) were predominant over those sensitized against hazelnut seed storage proteins (Sprot, Cor a 9 and 14), which displayed higher IgE reactivity. The protease E5 effectively hydrolyzed proteins from hazelnut and pistachio, while E7 was efficient for cashew protein hydrolysis. When combined with pressured heating (autoclave and Controlled Instantaneous Depressurization (DIC)), these proteases notably reduced the allergenic reactivity. The combination of DIC treatment before enzymatic digestion resulted in the most effective methodology to drastically reduce or indeed eliminate the allergenic capacity of tree nuts.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

A heat pump with thermal storage system is a system that operates a heat pump during night-time using inexpensive electricity; during this time, the generated thermal energy is stored in a thermal storage tank. The stored thermal energy is used by the heat pump during daytime. Based on a model of a dual latent heat storage tank and a heat pump, this study conducts control simulations using both conventional and advanced methods for heating in a building. Conventional methods include the thermal storage priority method and the heat pump priority method, while advanced approaches include the region control method and the dynamic programming method. The heating load required for an office building is identified using TRNSYS, used for simulations of various control methods. The thermal storage priority method shows a low coefficient of performance (COP), while the heat pump priority method leads to high electricity costs due to the low use of thermal storage. In contrast, electricity costs are lower for the region control method, which operates using the optimal part load ratio of the heat pump, and for dynamic programming, which operates the system by following the minimum cost path. According to simulation results for the winter season, the electricity costs using the dynamic programming method are 17% and 9% lower than those of the heat pump priority and thermal storage priority methods, respectively. The region control method shows results similar to the dynamic programming method with respect to electricity costs. In conclusion, advanced control methods are proven to have advantages over conventional methods in terms of power consumption and electricity costs.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

Due to an urgent need for reducing the fast progressing climate changes, a rapid, standardized and replicable solution for the infrastructure restructuring of heat demand coverage of buildings at district and city level must be developed. As more and more communities in Europe, especially in Germany, are obligated to have plans for coverage of heat demand, city planners, energy agencies seek a tool, which will help them to design the first drafts of heating network routes, which can supply whole districts and cities with renewable energy. ArcGIS Pro Tools like Least-Cost-Path-Analysis (LCPA) and Closest Facility (CF) allow to find the shortest and “cheapest” way between the heat source and heat consumers in the analyzed areas. Starting from the community level, through the district, county, voivodeship and whole country levels, the replication of the methods for generating district heating (DH) network infrastructure can be achieved. The proposed LCPA and CF based methods help to design the most suitable and efficient DH networks in the analyzed areas. As only few open-source data input, like street networks and building footprints are needed, the methods can be implemented in all communities of the country of Poland. In this paper one example of one community of Wroclaw county, called Siechnice and surroundings is presented.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

Influence of Joule heating on magnetic properties, giant magnetoimpedance (GMI) effect and domain wall (DW) dynamics of Fe75B9Si12C4 glass-coated microwires was studied. A remarkable increase in GMI ratio is observed in Joule heated samples. The hysteresis loops of Joule heated samples maintain a rectangular shape, while a slight decrease in coercivity after Joule heating is observed. On the other hand, a modification of MOKE hysteresis loops is observed upon Joule heating. Additionally, DW dynamics improvement after Joule heating is observed. The observed GMI ratio improvement along with the change in MOKE loops and DW dynamics improvement has been discussed considering magnetic anisotropy induced by Oersted magnetic field in the surface layer during Joule heating and the internal stress relaxation. A remarkable GMI ratio im-provement observed in Fe-rich Joule-heated microwires with a rectangular hysteresis loop and fast DW propagation, together with the fact that Fe is a more common and less expensive metal than Co, makes them suitable for use in magnetic sensors.

High-density olive groves, despite their interesting production potential, have several limitations, also due to the high fruit load and the irrigation requirements.The study aimed to evaluate the effects of fruit load and deficit irrigation on oil yield and fruit quality, and on olive chemical composition in a high-density olive grove (cv Sikitita). Our main hypothesis was that the primary metabolism, as influenced by crop load and stress, could modify the accumulation of different phenolic classes.Different fruit loads were generated through flower thinning (66%, 50%, 33%, 0%) and two deficit irrigation treatments (-60%, -75%) were compared to the well-watered control (920 m3/ha).Thinning treatments had a limited effect on oil yield, on the other hand, deficit irrigation caused considerably less oil accumulation in the fruit on all sampling dates.Thinning 66% and deficit irrigation 75% were considered with the control for untargeted metabolomic analysis, considering three sampling dates. 233 different phenolic compounds were annotated. Multivariate HCA results indicated the impact of harvest time on the phenolic profile of olive fruits, yielding two separate clusters grouping t1 and t2 together and apart from t3. Regarding agronomic techniques, they played a differential role in the phenolic profile (supervised OPLS – DA). Fruit load mostly affected flavonoid glycosides. In contrast, the phenolic response to deficit irrigation is more heterogeneous, with phenolic acids (35%), flavonoids (25%), LMW, and other phenols (25%).

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

Steel products have experienced long-standing problems such as unstable product quality and low product homogeneity. In the continuous casting process, realizing constant temperature pouring is an effective way to improve product homogeneity. Plasma heating can compensate for the temperature drop during casting with a tundish and maintain a stable degree of superheating of the molten steel in the tundish. Plasma heating has a certain impact on the cleanliness of the molten steel and on the tundish covering flux in the tundish while compensating for the temperature drop. This paper uses SEM-EDS, XRD and FactSage to analyze the cleanliness of the molten steel and the characteristics of the tundish covering flux before and after heating. The results show that the number density of inclusions in the tundish is significantly lower after heating, improving the floating removal rate of small-sized inclusions; after heating, the surface morphology of the tundish covering flux sample appears transparent and glassy, with uniform morphology; XRD results show that the tundish covering flux after plasma heating exhibits no crystal precipitation and is amorphous and that there is a certain regularity before and after heating; there are no obvious changes in the composition of the tundish covering flux in the liquid phase area.

Cancer is a leading cause of morbidity and mortality worldwide, yet much is still unknown about its mechanism of establishment and destruction. Recently, studies had shown that tumor cells cannot survive under the high temperature conditions. This treatment technique is called Hyperthermia. This report presents the case of radiative microwave heating of hyperthermia therapy on breast cancer in a porous medium. In this study, the steady state is solved analytically while unsteady state is solved using semi-implicit finite difference to get a more accurate prediction of blood temperature distributions within the breast tissues. A moderate temperature hyperthermia treatment is apply which results into cell death due to an increase in the level of cell sensitivity to radiation therapy and blood flow in tumor and oxygen. The results show that by applying metabolic heat generation rate of $3.97 X 10^{5}Wm^{-3}$, it takes upto 2 minutes for the tumor cells to get the require therapeutic temperature point.

Olive trees have a unique reproductive pattern marked by biennial fruiting. This study delves into the repercussions of alternate fruit bearing on the water relations of olive trees and the associated ecophysiological mechanisms. The experiment spanned two consecutive years: the "ON" year, characterized by a high crop load, and the "OFF" year, marked by minimal fruit production. Key ecophysiological parameters, including sap flow, stomatal conductance, and photosynthetic rate, were monitored in both years. Pre-dawn water potential was measured using continuous stem psychrometers and the pressure chamber technique. Biochemically, non-structural carbohydrate concentrations (starch, sucrose, and mannitol) and the carbon-stable isotope ratio (δ13C) in olive leaves were examined. Results unveiled heightened leaf gas exchange during the "ON" year, leading to increased water consumption and photosynthetic rates. This escalated water usage during the "ON" year significantly reduced leaf water potential. Sucrose and starch concentrations were notably elevated in the "ON" year, with no significant impact on mannitol concentration. Regarding the carbon stable isotope ratio, leaves from the "OFF" year exhibited significantly higher δ13C abundance, indicative of heightened resistance to the CO2 pathway from the atmosphere to carboxylation sites compared to the "ON" year plants.

In this paper, a special recurrent neural network (RNN) called \emph{Long Short-Term Memory (LSTM)} is used to design a virtual load sensor that estimates the mass of heavy vehicles. The estimation algorithm consists of a two-layer LSTM network, with the two layers based on sequence-to-sequence and sequence-to-one logic, respectively. The network estimates the vehicle mass based on the vehicle speed, longitudinal acceleration, engine speed, engine torque, and the accelerator pedal position. The network is trained and tested with a data set collected in a high-fidelity simulation environment called Truckmaker. Training data is generated in acceleration maneuvers in a range of speeds whereas test data is obtained by simulating the vehicle in a Worldwide harmonized light vehicles test cycle (WLTC). Preliminary results show that, with the proposed approach, the heavy-vehicle mass can be estimated as accurately as commercial load sensors in a range of load mass as wide as four tons.

For many years, energy monitoring at the most disaggregate level has been mainly sought through the idea of Non-Intrusive Load Monitoring (NILM). Nevertheless, a practical application of this concept in the residential sector should address the underlying concerns raised by the technical specifications of case studies. From one side, such an operation must handle common matters related to the essence of any NILM system. Although this aspect has been thoroughly investigated by basic research, it is limited to the properties of public datasets. On the other side, it must deal with specific concerns corresponding to uncommon situations. These circumstances impose further restrictions on existent NILM schemes, however, they have been overlooked due to the lack of pertinent databases to scrutinize. Accordingly, this paper presents applied research on a potential solution to NILM for Quebec residences. It carries out a relevant investigation into the multi-faceted nature of this problem in order to reveal barriers to feasible implementations in the context of Quebec. This work commences with a concise discussion about the NILM idea to highlight its essential requirements for a fruitful practice. Afterward, it provides a comparative statistical analysis to represent the specificity and potential challenges of the case study in accordance with NILM necessities. For this purpose, the examination exploits data from real-world measurement systems in the same and European regions. Subsequently, this study focuses on a load identification exercise by proposing a combinatory approach that utilizes the promise of sub-meter smart technologies to integrate the intrusive aspect of load monitoring with the non-intrusive one. The former is aimed at extracting overall heating demand from the aggregate one by a supervised procedure based on Deep Learning (DL) models while the latter is designed for disaggregating the residual load through an unsupervised process on the basis of clustering techniques. The results demonstrate that geographically-dependent cases create electricity consumption scenarios under which existing NILM methods can be questioned. From a realistic standpoint, this research elaborates on critical remarks to realize viable NILM systems, particularly, in Quebec houses.

The load on the top of a slope is an important cause of slope failure, and it is of great significance to study the relationship between the load and the stability of the slope. This paper uses elastic theory and Moore Coulomb's theory as transformation conditions to obtain the slope stability coefficient expression under slope top load based on the Swedish slice method. In view of the actual engineering, the corresponding slope model structure was established, and 5 sliding surfaces were set with the crack on the top of the slope as the shear outlet. According to the slope stability coefficient expression, the stability coefficient of the set sliding surface is solved. The result shows that the slope is unstable under the load. The judgment result is consistent with the GEO-STUDIO check calculation result. This method can provide reference for theory and engineering practice.

In the theoretical treatment of crystallization it is commonly assumed that relaxation processes of the liquid proceed fast as compared to crystal nucleation and growth processes. Actually, it is supposed that the liquid is located always in the metastable state corresponding to the current values of pressure and temperature. However, near and below the glass transition temperature, Tg, this condition is commonly not fulfilled. In such cases, in the treatment of crystallization, deviations of the state of the liquid from the respective metastable equilibrium state have to be accounted for in determining the kinetic coefficients governing the crystallization kinetics, the thermodynamic driving force of crystallization, and the surface tension of the aggregates of the newly evolving crystal phase including the surface tension of critical clusters affecting considerably the crystal nucleation rate. These factors may considerably influence the course of the overall crystallization process. A theoretical analysis of the resulting effects is given in the present paper by numerical solutions of the J(ohnson)–M(ehl)–A(vrami)–K(olmogorov)–equation employed as the tool to model the overall crystallization kinetics and by analytical estimates of the crystallization peak temperatures in dependence on cooling and heating rates. The results are shown to be in good agreement with experimental data. Possible extensions of the theory to be explored in future analysis are anticipated.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

As use of composite materials increases, the search for suitable automated processes gains relevance to guarantee production quality by ensuring uniformity of the process, minimizing the amount of generated scrap and reducing time and energy consumption. Limitations on production by traditional means such as hand lay-up, vacuum bagging and in-autoclave methods, tend not to be as efficient when the size and shape complexity of the part being produced increases, motivating the search for alternative processes such as the Automated Tape Laying (ATL). This work aims to describe the process of modelling and simulating a composite ATL with in situ consolidation by characterizing the machine elements, using the finite differences method in conjunction with energy balances, in order to create a digital twin of the process for further control design. The modelling approach implemented is able to follow the process dynamics when changes to the heating element are imposed as well as to predict the composite material temperature response, making it suitable to work as a digital twin of a production process using an ATL machine.

Non-tuberculous mycobacteria (NTM) are opportunistic pathogens that cause illness primarily in the elderly, in the immunocompromised or in patients with underlying lung disease. Mycobacterium chimaera is a NTM species belonging to the M. avium Complex (MAC) group of species. Since 2013, a global outbreak of M. chimaera infection related to heater-cooler units (HCU) used in cardio-thoracic surgery has been identified. This outbreak was caused by a single strain of M. chimaera. In order to estimate the prevalence of this outbreak strain in Israel, we sampled M. chimaera from several HCU machines in Israel, as well as from patients, sequenced their genomes and compared them to the outbreak strain. The presence of mixed mycobacteria species in the samples complicated the analysis of obtained sequences. By applying a metagenomic binning strategy, we were able to obtain genomes of single strains from the mixed samples, and characterized them. M. chimaera strains were compared to each other and to previously reported genomes from other countries. The strain causing the outbreak related to the HCU machines was identified in several such machines in Israel but not in any of the clinical samples.

Abstract: The traditional model of closed circuit ball milling systems has been used for several decades, however, if the classifier of the closed circuit ball mill system performs the duties of both pre-classification and check-classification, the characterization error of the traditional model is large. To address this problem, a new model is obtained by modifying and supplementing the traditional one. The most important feature of the new model compared to the traditional model is that the circulating load is considered to be the fresh feed for the entire system rather than the ball mill. The error between the slurry level height calculated using the traditional model and the actual is 52.31%, which is 13.77 times higher than that of the new model. When the relative capacity varies greatly, that of the ball mill calculated by the traditional model fluctuates between 0.95 and 1.15, while the new model is 0.6 to 1.4. The new model has a higher accuracy than the traditional model in characterizing the production status of the grinding system, which is of some significance for industrial production.

The COVID-19 pandemic has led to the growth of hybrid and online learning environments and the trend to introduce more technology into the classroom. One such change would be the use of smart synchronous hybrid learning environments (SSHLE), which are settings with both in-person and online students concurrently, and in which technology plays a key role in sensing, analyzing, and reacting throughout the teaching and learning process. These changing environments and the incorporation of new technologies can place a greater orchestration load on participants and a reduction in teacher agency. In this context, the aim of this paper is to analyse the orchestration load and teacher agency in different SSHLEs. The NASA-TLX model was used to measure the orchestration load in several scenarios. Questionnaires and interviews were used to measure teacher agency. The results obtained indicate that the orchestration load of the teacher tends to be high (between 60 and 70 points out of 100 of the NASA-TLX workload), especially when they lack experience in synchronous hybrid learning environments, and the orchestration load of the students tends to have average values (between 50 and 60) in the SSHLEs analysed. Meanwhile, the teacher agency does not appear to be altered but shows potential for improvement.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

Macrophages are the key effector cells of innate immunity which show two polarized states: M1, classically activated and M2, alternatively activated. Tumor-associated macrophages (TAMs) which usually show M2 polarization, are immunosuppressive cells that enhance tumor metastasis and invasion. Also, enrichment of TAMs is known to be closely associated with poor prognosis of cancer patients. Therefore, TAMs are considered to be promising targets for immunotherapy. Importantly, tumor-derived exosomes emerged as a crucial player in immune regulation which can remodel the tumor microenvironment towards immunosuppressive state. Of note, few studies have shown that exosomes could induce polarization of macrophages towards M2 type in tumor condition, while others showed activation of M1 or mixed phenotype. Considering the role of TAMs in cancer, there is an urgent need to decipher the exosome-mediated cross-talk between tumor cells and macrophages.For this, we used murine model of Dalton’s lymphoma (DL), wherein, firstly, we evaluated increased exosome burden by assessing exosome level in serum as well as in various tissues of tumor-bearing host. Next, proteomic profiling of lymphoma-derived exosomes was done which revealed the presence of immunomodulatory proteins. Of note, these proteins were known to alter the macrophage polarization. In order to assess the effect of these exosomes on macrophages, we performed in vitro study using RAW264.7 cells. In vitro study revealed that frequent uptake of exosomes mediated a morphological change in macrophages which reduced their phagocytic activity. In parallel, exosomes increased reactive oxygen species (ROS) level and inhibited LPS-induced nitric oxide (NO) level in macrophages. Also, exosomes upregulated the expression of arginase-1 (an M2 marker) in macrophages but decreased the LPS-induced nitric oxide synthase 2 (NOS2) (an M1 marker) expression. Moreover, we observed a pro-tumoral cytokine profile in macrophages incubated with exosomes. Our study suggests that exosome load increases in lymphoma-bearing hosts systemically. Importantly, lymphoma-derived exosomes mediate the activation of macrophages towards pro-tumoral M2 type. Our results give an insight into the exosome-mediated tumor and immune cell cross-talk which could serve as an important prospect for targeting in cancer immunotherapy.

Internet of things (IoT) is a network of smart things. This indicates the ability of these physical things to transfer information with other physical things. The characteristics of these networks, such as topology dynamicity and energy constraint, challenges the routing problem in these networks. Previous routing methods could not achieve the required performance in this type of network. Therefore, developers of this network designed and developed specific methods in order to satisfy the requirements of these networks. One of the routing methods is utilization of multipath protocols which send data to its destination using routes with separate links. One of such protocols is RPL routing protocol. In this paper, this method is improved using composite metrics which chooses the best paths used for separate routes to send packets. We propose Energy and Load aware RPL (ELaM-IoT) protocol, which is an enhancement of RPL protocol. It uses a composite metric, calculated based on remaining energy, hop count, Link Expiration Time (LET), load and battery depletion index (BDI) for the route selection. In order to evaluate and report the results, the proposed ELaM-IoT method is compared to the ERGID and ADRM-IoT approaches with regard to average remaining energy, and network lifetime. The results demonstrate the superior performance of the proposed ELaM-IoT compared to the ERGID and ADRM-IoT approaches.

In this paper is discussed sediment transport as a mechanical process that characterises a natural stream or channel flow regime. The objective of experimental work presented in this paper is to recall and to give another prospect of well-known Meyer-Peter and Müller approach for estimation of Shield’s number (θ_c,θ) in laboratory conditions, and calibration of dimensionless MPM number (A). For this purpose two different experiments are conducted, during the first experiment water amount flushed on the flume and bed slope was changed simultaneously until equilibrium state is achieved, meanwhile is estimated the critical Shield’s number (θ_c). While, during the second experiment, water amount was kept constant, only bed slope of flume was continuously tilted, meanwhile sediment, discharge and Shield’s number (θ) was determined for given hydraulic conditions. In addition calibration of dimensionless MPM number (A) was performed, where several iteration were considered until for (A=3.42), sediment discharge measured become almost equal with sediment discharge computed by using MPM formula. After these experiments, is concluded that MPM formula can be used also for other certain initial condition and similar procedure may be adopted to calibrate the dimensionless MPM number (A) .

A Gem-quality rubies and sapphires are often commercially heat treated at about 800°C or higher temperatures to enhance their colour and clarity, and hence quality. For this study, selected corundum samples containing diaspore- and goethite inclusions were heated step-by-step to a maximum of 1000 °C with the aim to monitor the dehydration and phase transformation of these oxyhydroxides to corundum and hematite during heating. Based on our experiments and in agreement with literature, the dehydration of diaspore in corundum occurs between 525 to 550 °C, whereas goethite transforms to hematite already between 300 and 325 °C. As both, diaspore and goethite are common inclusions in rubies, sapphires, and other corundum varieties, these dehydration reactions and phase transformations can be considered important criteria to separate unheated stones from heated ones, specifically in cases in which other methods (e.g. microscopy, FTIR) are unsuccessful.

The focus of this study was to evaluate the effectiveness of incorporation of phenolic compounds from blueberry juice into pear slices using a combination of ohmic heating (OH) and vacuum impregnation (VI), followed by air- or freeze-drying. The results showed that OH is a valuable technique to increase the content of bioactive compounds and antioxidant capacity of blueberry juice. The optimal OH treatment is heating the juice at 50 °C for 20 min under an electric field of 13 V/cm. Furthermore, the combination of VI and OH showed the efficiency of enriching pear slices with bioactive compounds from blueberry juice. The best treatment is to immerse the slices for 90 min at 50 °C and an electric field of 7.8 V/cm. The presence of anthocyanin pigments from blueberry juice affects the color parameters of pear slices by increasing the a* parameter and decreasing the b* and L* parameters. However, both freeze-drying and air-drying (at temperatures of 40, 50, and 60 °C) negatively affected the phenolic content and antioxidant capacity. Notably, air-drying at 60 °C highest levels of phenolic compounds and antioxidant potential for both impregnated and non-impregnated pear slices among the drying processes applied.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

The aim of this study was to determine the effect of sous-vide and pressure-cooker heating of pork muscles (Longissimus lumborum) on the physicochemical and technological characteristics of pork. The study included an analysis of the basic composition, colour, texture, nutritional value (vitamin B1 content), and rheological properties of meat heated at 60°C for 6-18h and, for comparison, in an autoclave at 121.1°C. The heating conditions affected the weight loss, colour, thiamine content, texture, and rheological properties of the meat. As the heating time increased, the texture determinants of firmness and chewiness decreased, which resulted in softer meat. The differences in the rheological properties of the sous-vide- and autoclave-heated meat resulted from different organ-isation of the spatial matrix of proteins and changes in the structure of muscle fibres caused by the high temperature.

Cobalt ferrite nanoparticles (NPs) doped with rare earth (RE) metals with general formula CoFe_2-xRE_xO₄ (RE=Yb, Dy, Gd; x = 0.0 - 0.3) were synthesized by the co-precipitation method followed by post thermal treatment. The influence of RE doping on structural, magnetic and thermal properties and potential biomedical applications like magnetic hyperthermia has been investigated. In the as-prepared samples RE cations enter the spinel lattice as detected by X-ray diffraction. Thermal treatment leads to thermodynamically stable and relaxed single-phase spinel structures only for lower RE content, x = 0.01-0.05. However, annealed samples present higher mass magnetization values (M_S), up to 83 Am²/kg. RE content also affects M_S, especially in the case of annealed samples where it decreases linearly with x from about 80 Am²/kg (x = 0.01) to about 60 Am²/kg (x = 0.30). Thermal treatment induces a reduction in coercivity from 60-100 mT for as-prepared samples to 18-33 mT for annealed samples, in a nonlinear manner with respect to RE content. Heating efficiency, i.e., Specific Loss Power (SLP), of all samples has been studied using both magnetometric and calorimetric method to deeper examine the energy loss mechanisms involved.

The paper deals with the modelization and optimization of an integrated multi-component energy system. On-off operation and presence-absence of components must be described by means of binary decision variables, besides equality and inequality constraints; furthermore, the synthesis and the operation of the energy system should be optimized at the same time. In this paper a hierarchical optimization strategy is used, adopting a genetic algorithm in the higher optimization level, to choose the main binary decision variables, whilst a MILP algorithm is used in the lower level, to choose the optimal operation of the system and to supply the merit function to the genetic algorithm. The method is then applied to a distributed generation system, which has to be designed for a set of users located in the center of a small town in the North-East of Italy. The results show the advantage of distributed cogeneration, when the optimal synthesis and operation of the whole system are adopted, and significant reduction in the computing time by using the proposed two-level optimization procedure.

In this research work the study of Buongiorno Model Darcy Forchheimer flow of Hybrid nanofluid flow on isothermal permeable stretch/shrink sheet with homogeneous and heterogeneous reaction is investigated. The effects of MHD, thermal radiation, viscous dissipation, Joule heating, and heat generation/absorption are taken into account. Hybrid nanofluids can act as a medium for heterogeneous-homogeneous reactions. The nanoparticles dispersed in the fluid can influence reaction kinetics and species transport, potentially, altering reaction rates and pathways. The applications of HNF in reactions, both homogeneous and heterogeneous, lie in leveraging their enhanced thermal properties, catalytic potential, and improved mixing capabilities to optimize reaction efficiency and control reaction conditions. Similarity transformation is used to convert a set of PDEs into a set of ODEs. HAM is used for the solution of the obtained ODEs system. In a heterogeneous reaction, the concentration gradient is amplified; in a homogeneous reaction, the impact is opposite. Moreover, at higher compositions of HNPs, the concentration and velocity rise while the temperature falls. Furthermore, as the values of homogeneous and heterogeneous reactions increase, the concentration falls. It is reliable with the idea that a greater reaction rate lowers the diffusion rate. Nevertheless, these parameters do not affect temperature or velocity.