This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

A homogenized, supersaturated Al-Zn-Mg-Zr alloy was processed by severe plastic deformation (SPD) using high-pressure torsion (HPT) technique for different revolutions at room temperature to get ultrafine-grained (UFG) microstructure. The microstructure and mechanical properties of the UFG samples were then studied by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), as well as by tensile and hardness measurements. Emphasis was placed on the effect of shear strain on the evolution of microstructure of the investigated alloy. Experimental results have shown a very interesting evolution of the decomposed microstructure in a wide range of shear strains imposed by HPT. While the global properties, such as the average grain size (~200 nm) and hardness (~2.2 GPa) appeared unchanged, the local microstructure was continuously transformed. After 1 turn of HPT, the decomposed UFG structure contains relatively large precipitates inside grains. In the sample processed by 5 turns in HPT, segregation of Zn atoms into grain boundaries (GBs) can also be observed. After 10 turns, more Zn atoms have segregated into GBs and only smaller size precipitates can be observed inside grains. The intensive segregation of solute atoms into GBs may significantly affect the ductility of the materials, leading to its ultralow-temperature superplasticity. Our findings pave the way for achieving advanced microstructural and mechanical properties in nanostructured metals and alloys by engineering their precipitation and segregation by means of applying different HPT regimes.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

The objective of this work was to evaluate the roast time, weight loss and quality of coffee grain at four different roasting degrees, aiming to recognize and develop sustainable patterns to industrialize specialty coffees. Coffee (Coffea arabica L.), from eight producers, with scores between 80 and 83 from SCA classification, were used. Samples of 300 g were roasted in a cylindric rotative roaster, until the grains reached four different roasting profiles (Agtron scale 22.36, #33.64, #40.05, #59.92). Afterwards, analysis of roasting time, gas pressure, weight loss, and sensorial grades were accomplished. It was observed that samples roasted at #22.36 led to significant differences, regarding roasting time and weight loss. Furthermore, there is a significant difference at the sensorial grades of the coffee beverage. Comparing the roast degree #40.05 (standard used for specialty coffee) with the roast degree #22.36 (most used for commodities coffee), the first one has a gas consumption of 0.34 kg per coffee kg, whilst the second presented a gas consumption of 0.41 kg per coffee kg. Thus, from gas consumption, roast degree # 40.05 is the more sustainable option, along with the remaining parameters analyzed.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

Magnesium (Mg) alloy is a widely used lightweight metal structural material due to its high specific strength and stiffness, excellent damping performance, and recyclability. Wrought Mg alloys are widely favored in fields such as aerospace, transportation, and biomedical stents. However, most wrought Mg alloys with a hexagonal close-packed (HCP) crystal structure lack sufficient independent slip systems to meet the von Mises criterion for uniform plastic deformation at room temperature. This can result in the formation of strong basal texture during plastic deformation and poor room temperature plastic forming ability. Improving the room temperature forming performance is a crucial challenge that must be addressed to broaden the application of Mg alloy sheets. Our research group has comprehensively summarized significant work and latest research progress in improving the room temperature forming of Mg alloy sheets via extrusion technology in recent years. Specifically, we have developed a new type of asymmetric extrusion technology that combines material structure evolution, mechanical property, and forming behavior analysis. We have elucidated the extrusion process characteristics, texture control mechanism, and forming properties of Mg alloy sheets through plastic deformation mechanisms, mold design, and finite element numerical simulation. Our findings provide a novel extrusion technology for the fabrication of highly formable Mg alloy sheets, which can be utilized in various applications.

Dengue virus (DENV) and chikungunya virus (CHIKV) are reemergent arboviruses that are transmitted by mosquitoes of the Aedes genus. During the last several decades, these viruses have been responsible for millions of cases of infection and thousands of deaths worldwide. Therefore, several investigations were conducted over the past few years to find antiviral compounds for the treatment of DENV and CHIKV infections. One attractive strategy is the screening of compounds that target enzymes involved in the replication of both DENV and CHIKV. In this review, we describe advances in the evaluation of natural products targeting the enzymes involved in the replication of these viruses.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average <Mg–O> and <Al–O> bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

This paper describes the preparation and description of four new complexes [Bu₂Sn(AA)Cl] (AA = glycine, DL-valine and L-leucine) and [Bu₂SnPhen₂] (Phen = DL-phenylalanine) They were characterized by elemental analyses of carbon, hydrogen, nitrogen, chlorine and tin; and by infrared, ^119mSn-Mössbauer and ^119mSn-RMN spectroscopies, and by the applications of TG and DSC techniques in dynamic helium atmosphere. For the [Bu₂Sn(AA)Cl], trigonal bipyramidal tin species, AA were coordinated bidentatedly by the carboxylic oxygen and by the NH₂ group. The [Bu₂SnPhen₂)], with tin atoms in trans-octahedral sites, had the Phen-coordinated by both carboxylic oxygen atoms.

Sporotrichosis’ clinical manifestations, lesions in the cutaneous or subcutaneous tissues, it is caused by dimorphic fungi of the Sporothrix complex, is a cosmopolitan mycosis that affects humans and animals. This study aimed to identify prevalent species in Minas Gerais, Brazil, and characterize virulence profiles and antifungal susceptibility associated with Sporothrix isolates. Isolates were identified using macro and micro-morphological traits as well molecular biology techniques. Antifungal susceptibility was determined using the Minimal Inhibitory Concentration test, while, virulence factors such as growth at different temperatures, biofilm formation, melanin production, and urease activity were assessed. Our findings revealed S. brasiliensis as a predominant species isolated. Urease activity was a crucial factor associated with growth at 50°C in S. brasiliensis isolates, highlighting their high thermotolerance. Furthermore, strains isolated from humans produced a more robust biofilm compare to those from felines. Strains of S. brasiliensis isolated from Felis catus exhibited faster melanin production, decreased susceptible to antifungal agents tested, and superior growth capacity at 50°C to strains isolated from humans. Therefore, our study highlights the prevalence of S. brasiliensis causing sporotrichosis in both human and felines. However, it underscores the circulation of different strains, with varying levels of virulence and susceptibility to antifungal agents.

Precipitates are the primary source of strength for the Al-Mg-Si alloy. Aluminum alloy in the peak-aged state mainly contain β'' and β' precipitates. In the past, most of the literature only considered the strengthening effect of β''. Here we develop a single crystal intensity model including both precipitate enhancement effects for the first time. This model was subsequently implemented into a crystal plastic finite element method to model the uniaxial tensile process of a polycrystalline aggregate model of Al-Mg-Si alloy. The simulation results for uniaxial stretching are in good agreement with the experimental results, confirming that the constitutive parameters used for the single crystal strength model with two precipitates are based on realistic physical implications. Furthermore, by comparing the uniaxial tensile simulation results of a peak-aged alloy considering the actual precipitated phase composition of the alloy with those assuming that the precipitated phase is only the β'' phase, the predicted tensile strength of the former is around 5.65% lower than that of the latter, suggesting that the two kinds of precipitation should be considered separately when simulating the mechanical response of Al-Mg-Si alloy. It is highly expected that the present simulation strategy is not limited to the Al-Mg-Si alloys, and it can be equally applied to the other age-enhanced alloys.

Several plant species produce mixtures of odorous and volatile compounds known as essential oils (EOs). These mixtures play important roles in nature and have been utilized by man for pharmaceutical and agrochemical purposes. There are more than 3000 EOs reported in the literature with approximately 300 having commercial use, including the oils from Eucalyptus species. Such oils are rich in monoterpenes and have found applications as pharmaceuticals, agrochemicals, food flavorants and in the perfume industry. Such applications are related to their diverse biological and organoleptic properties. In view of their importance, we review in this article up to date information concerning chemical composition and biological activities of essential oils from different species of Eucalyptus. Among the 900 species and subspecies of the Eucalyptus genus¸ we examined 68 species. The studies associated with these species were conducted in 27 countries. We have focused on the antimicrobial, acaricide, insecticide and herbicide activities, hoping that such information will contribute in the advances of the research in this field. It is also intended that the information herein described can be useful in the rationalization of the use of Eucalyptus EOs as components for new pharmaceutical and agrochemical applications as well as food preservatives and flavorants.

The environmental vulnerability diagnosis of a river basin depends on a holistic analysis of its environmental aspects and degradation factors. Based on this diagnosis, the definition of priority areas where interventions for environmental recovery should be carried out is fundamental, since financial and natural resources are limited. In this study, we developed a methodology to assess these fragilities using an Environmental Vulnerability Index (EVI) that combines physical and environmental indicators related to the natural sensitivity of ecosystems and their exposure to anthropogenic factors. The EVI developed was applied to the headwater’s region of the São Francisco River basin, Brazil. The proposed index was based on the AHP multi-criteria analysis and was adapted to include four variables representative of the study area: Land Use Adequacy, Burned Area, Erosion Susceptibility and Quantitative Water Balance. The EVI analysis highlighted that the presence of easily erodible soils, associated with sloping areas and land uses above their capacity, generate the most vulnerable areas in the headwaters of the São Francisco River basin. The results of this study indicate where resources should be applied for environmental preservation in the basin under study, directing the allocation of efforts to areas with lower resilience in maintaining ecosystem services.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Background: Gait analysis systems offer invaluable insights for rehabilitation, yet their expense limits clinician access. We developed GAITWell®, a low-cost modular system for capturing spatiotemporal gait variables, and evaluated its measurement properties. Methods: The GAITWell® uses discreet binary sensors on interconnected boards to collect gait data, which is then analyzed using the DBSCAN algorithm on the Cartesian points from sensor outputs. Reliability was assessed using ICC2,1, standard error of the mean (SEM) and Bland-Altman plots. Validity was determined by comparing GAITWell® with the Qualisys Pro-Reflex system. Results: Participated 38 healthy adults, with an average age of 33.2 years (SD 13.0). Correlations between GAITWell® and the Qualisys system ranged from moderate to very high for most gait variables, with the exception of stride length, which demonstrated a low but significant correlation (r = .360, p < .05). The ICC2,1 indicated moderate to good agreement for most gait variables. Stance and double support times, cadence, and base of support exhibited poor reliability, characterized by larger SEM and limits of agreement. Conclusions: Our findings indicate that the GAITWell® system is a promising tool for gait analysis. Future research will enhance sensor accuracy and refine algorithms to improve reliability.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

Euler-Poisson equations of a charged symmetrical body in external constant and homogeneous electric and magnetic fields are deduced starting from the variational problem, where the body is considered as a system of charged point particles subject to holonomic constraints. The final equations are written for the center-of mass-coordinate, rotation matrix and angular velocity. General solution to the equations of motion is obtained for the case of a charged ball. For the case of a symmetrical charged body (solenoid), the task of obtaining the general solution is reduced to the problem of a one-dimensional cubic pseudo-oscillator. Besides, we present a one-parametric family of solutions to the problem in elementary functions.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

This paper addresses the parameter identification of a one-link flexible manipulator based on the experimental measurement of the inputs/outputs, the finite element model, and the application of evolutionary algorithms. A novel approach is proposed to find the values of inertia, stiffness, and damping parameters by minimizing the difference between the numerical model’s outputs and the testbed’s outputs, considering the joint position and acceleration of the link’s tip. The dynamic model is initially obtained using the finite element method and the Lagrange principle. A prototype of a single one-link flexible manipulator is used in the experimental application wherein the servomotor applies the input torque, and the outputs are the joint angle and the link’s tip acceleration. Then, an optimization problem minimizes the difference between numerical and experimental outputs to determine the set of parameters using evolutionary algorithms. A comparative analysis to obtain the identified parameters is established using genetic algorithms, particle swarm optimization, and differential evolution. The proposed identification approach permitted the determination of the dynamic parameters based on the complete dynamic model of the flexible-link manipulator, which is different from the approaches reported in the literature that identify a simplified model. This information is essential for the design of the motion and vibration control laws.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

The growing demands of material longevity in marine environments necessitate the development of highly efficient, low-cost and durable corrosion protective coatings. Although magnesium alloys are widely used in the automotive and aerospace industries, severe corrosion issues still hinder their long-term service in naval architecture. In present work, an epoxy composite coating containing sericite nanosheets is prepared on the AZ31B Mg alloy by one-step electrophoretic deposition method to improve corrosion resistance. Due to the PEI modification, positively-charged sericite nanosheets can be highly orientated in an epoxy coating under the influence of an electric field. The sericite-incorporated epoxy coating prepared in the emulsion with 4 wt.% sericite exhibits the highest corrosion resistance in 3.5 wt.% NaCl solution, as manifested by electrochemical corrosion and long-term immersion tests. The highly-orientated sericite nanosheets in epoxy coating provide excellent barrier effect against corrosive media, thereby significantly improving the long-term anti-corrosion performance of the epoxy coating. This work provides new insight toward the design of lamellar filler/epoxy coatings with superior anticorrosion performance and shows promise in the corrosion protection of magnesium alloys.

Rare earth rich magnesium alloys are used in aerospace and automotive fields because of their high specific strength and good castability. However, due to their low corrosion resistance, protective surface treatments, such as conversion coating or electroless plating are necessary, when they have to be used in humid or corrosive environments. The present study was aimed to evaluate the effect of Plasma Electrolytic Oxidation (PEO) and different surface roughness (Ra≈0.8 μm and Ra≈0.3 μm) on the rotating bending fatigue of an innovative Mg alloy, with a high content of Nd (up to 3.1 wt%) and Gd (up to 1.7 wt %). Fatigue tests revealed a 15% decrease in the fatigue strength of the PEO treated alloy (fatigue strength = 88 MPa) with respect to the bare alloy (fatigue strength = 103 MPa). The reduction of fatigue strength was mainly due to the residual tensile stresses induced by the PEO treatment. The effect of surface roughness on the bare alloy was, instead, negligible. The mechanisms of crack initiation were similar in the untreated and PEO treated alloy, with crack nucleation sites located in correspondence of large facets of the cleavage planes.

A comparative analysis between Bidirectional Evolutionary Structural Optimization (BESO) and Smoothing-ESO (SESO), simultaneously considering Reliability-Based Topology Optimization (RBTO) and the structure's self-weight in the case of three-dimensional elasticity, is presented in this study. Due to the important role of the existence of uncertainties in making the structural design more realistic, geometry, volumetric fraction, modulus of elasticity, compliance, and loading are considered random variables with normal probability distribution. When adopting the First Order Reliability Method (FORM), the failure probability is calculated based on the reliability index. Furthermore, considering the influence of self-weight in problems involving large structures in civil engineering, especially in the case of bridges, makes the optimal configuration more reliable for design. A series of examples are covered to validate the methods presented, showing their efficiency and robustness.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

Al-6%Mg-Sc-Zr alloys with the total ratio of Sc + Zr = 0.32 wt.% make up the target of this research. The content of scandium and zirconium varied with an increment of 0.02%. The alloys were produced by induction casting. Their ultrafine-grained (UFG) microstructure was formed with Equal Channel Angular Pressing (ECAP). Such cast alloys have a homogeneous macrostructure formed by small equiaxed grains in the central part of the ingot and columnar crystals along the edges of the cross section. After ECAP, the average grain size in the alloy specimens is 0.5–1 µm. The average grain size does not depend on the ratio of Sc and Zr in these alloys. Superplasticity tests were performed at temperatures ranging from 300 to 500 °C and at a strain rate varying between 3.3·10-3 and 3.3·10-1 s-1. UFG Al-6%Mg-0.20%Sc-0.12%Zr and Al-6%Mg-0.18%Sc-0.14%Zr alloys exhibit the highest superplasticity. It was suggested that changes in Sc:Zr ratio affect spatial distribution and composition of the following precipitating particles: Al3Sc, Al3Zr, Al3(ScxZr1-x). An increase in Zr concentration is shown to reduce the susceptibility of UFG alloys to cavitation fracture.

Background: Gender differences characterize the prevalence and attitudes toward weight management. Despite limited evidence suggesting greater weight loss in women with anti-obesity pharmacotherapy, gender-specific analysis remains underexplored. This retrospective study aimed to evaluate the gender-specific response to liraglutide 3.0 mg treatment in people with obesity without type 2 diabetes (T2D). Methods: Data were collected from 47 patients (31 women, 16 men), with age > 18 years, BMI ≥ 30 kg/m^2, absence of T2D, and with exclusion of prior anti-obesity treatment, comorbidities, or bariatric surgery. Only patients who maintained the liraglutide 3.0 mg dose for at least 6 months were included. Results: Both sexes showed significant reductions in weight and BMI at 3 and 6 months. Men achieved greater weight loss (WL), BMI reduction, % WL, WL >5% and >10% than women, and they also showed more significant improvements in metabolic parameters (total and LDL cholesterol, Fibrosis-4 Index FIB-4). No significant gender differences were observed in glucose metabolism or renal function. Conclusion: This study showed a greater therapeutic effect of liraglutide 3.0 mg in men. Given men's higher risk of cardiovascular disease (CVD), and underrepresentation in clinical weight loss programs, these findings may increase male engagement and improve their CVD risk.

This paper presents an observer-based dynamic output feedback controller design procedure using Linear Matrix Inequality (LMI) optimization for second-order systems with uncertainty and persistent perturbation in the states. Using linear-quadratic criteria, cost functions are minimized in a two-stage procedure to compute optimal state feedback gains, and observer gains are coupled into a dynamic output feedback optimal controller. The LMI set used in the two stages is matrix inversion-free, a key issue for polytope formulation when uncertainty is present. The approach is tested in a mobile inverted pendulum robotic platform, and the effectiveness is verified in this underactuated and undesensed case.

Exogenous melatonin, a nutraceutical for maintaining a healthy sleep-wake cycle and managing sleep disorders, requires large, repeated doses due to low bioavailability and short half-life. This necessitates the development of a sustained-release formulation with a longer half-life and sustained plasma concentration. Therefore, exogenous novel 5 mg sustained-release melatonin capsules (Melatonin-SR, test product) were formulated. This open-label cross-over study compared the pharmacokinetics (maximum concentration [Cmax], time to reach Cmax [Tmax], area under the curve [AUC] and elimination half-life [t1/2]) and safety of Melatonin-SR with 5 mg immediate-release melatonin capsules (Melatonin-IR, reference product) after single-dose oral administration in healthy fasting adults. Sixteen participants (aged 18-45 years) were randomized (1:1) to receive either Melatonin-SR or Melatonin-IR in two periods with a 7-day washout period. Melatonin-SR reported lower Cmax (11446.87 pg/mL) compared to Melatonin-IR (22786.30 pg/mL). The mean Tmax of Melatonin-SR and Melatonin-IR was 1.26 h and 0.87 h, respectively. The mean t1/2 of Melatonin-SR (5.10 h) was prolonged by five-fold compared to Melatonin-IR (1.01 h). One adverse event (vomiting) was reported following administration of the Melatonin-IR. Melatonin-SR resulted in higher and sustained plasma melatonin concentrations for an extended period and was well-tolerated. Hence, Melatonin-SR may be a promising nutraceutical for maintaining healthy sleep.

The objective of this study was to evaluate the genetic effects involved on pepper fruit post-harvest water loss, and correlated to morphology traits. Fruits of eight landraces of C. baccatum, and their 28 hybrids, were evaluated in a randomized complete block design. Analysis of variance, diallel analysis, phenotypic and genotypic correlation were performed to compare fruit water loss (WL), width (FW), length (FL), total soluble solids (TSS), dry matter content (DMC), pericarp thickness (PT), cuticle thickness (CT), and exocarp thickness (ET). WL varied from 14 to 68% during storage. Non-additive effects played more important role than additive, including CT, EP and TSS. Effective strategies to reduce WL should be achieved by repeated backcrosses followed by selection in segregating populations (SP). Therefore, the selection of hybrids should follow high specific combining ability traits. Selecting fruits with higher CT and lower TSS values are indirectly selecting fruits with lower WL. Varieties with low WL can be breed using landraces 04 and 58 as parents or by the hybrid 04 x 44 in open lines in SP. Brazilian C. baccatum landraces are a source of genetic variability, and the SP emerging from crossing lines with reduced WL should develop new ways for conventional breeding.

Myasthenia gravis (MG) is a disease characterized by typical clinical and immunopathogenic pe-culiarities, which correlate with age and sex/gender. Accordingly, MG patients show thymic al-terations and auto-antibodies productions, that can be the expression of a different pathogenetic mechanism related to age and gender. This determines, in relation to age at and sex/gender, a dif-ferent MG onset, prognosis, and outcome. Therefore, diverse MG forms can be identified, classi-fied, and characterized in relation to their different features, and precisely there are early onset and late-onset forms of MG. It has been hypothesized that the cause of appearance the two diverse forms of MG can be ascribed mainly to the diverse genetic and epigenetic factors. In this narrative review, we will analyze and discuss about the interplay of age- and sex-related factors (i.e. genet-ic and epigenetic factors) related to two different MG forms and how they contribute to their di-verse pathogenesis.

Clay minerals surfaces potentially played a role in prebiotic synthesis through adsorption of organic monomers that give rise to highly concentrated systems; facilitate condensation and polymerization reactions; protection of early biomolecules from hydrolysis and photolysis; and surface-templating for specific adsorption and synthesis of organic molecules. This review presents processes of clay formation using saponite as a model clay mineral since it is shown to catalyze organic reactions, easy to synthesize in large and pure form, and has tunable properties. In particular, a method involving urea is presented as a reasonable analog of natural processes. The method involves a two-step process – 1) formation of the precursor aluminosilicate gel and 2) hydrolysis of a divalent metal (Mg, Ni, Co, Zn) by the slow release of ammonia from urea decomposition. The aluminosilicate gels in the first step forms a 4-fold-coordinated Al³⁺ similar to what is found in nature such as in volcanic glass. The use of urea, a compound figuring in many prebiotic model reactions, circumvents the formation of undesirable brucite, Mg(OH)₂, in the final product by slowly releasing ammonia thereby controlling the hydrolysis of magnesium. In addition, the substitution of B and Ga for Si and Al in saponite is also described The saponite products from this urea-assisted synthesis were tested as catalysts for several organic reactions including Friedel-Crafts alkylation, cracking and isomerization reactions.

The main challenge in milk production has been to maintain a focus on efficient processes that enhance production outcomes, while aligning with animal welfare and sustainability and being valued by society. As an alternative to improve cow welfare in production and provide better handling of the waste generated by the activity, the system called compost-bedded pack barn (CBP) is an alternative that has been widely adopted in countries with temperate climates and higher milk production. This CBP has been attracting global interest, including from countries with tropical and subtropical climates, such as Brazil, where many producers have started to use it due to the response in terms of milk productivity. A CBP can be designed either in a) an open facility with natural ventilation or positive pressure ventilation system or b) totally closed facilities, equipped with negative pressure ventilation systems and permanent thermal control. The latter system is being implemented in Brazil, despite insufficient knowledge about its efficiency. The objective of this study was, through a review, to gather and describe the most recent information on the use of open and closed CBP systems for dairy cattle housing, mainly how it is applied in tropical climate regions. To achieve the proposed objective, this review study included the following topics related to CBPs: (i) implementation; (ii) bedding; (iii) general construction and architectural characteristics; iv) ambient thermal conditioning. Knowledge gaps and directions for future research are also identified.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

SLM Additive Manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabrication of different structures in aerospace industry. The importance of the evaluation of residual stresses that arise as a result of complex 3D-printing process thermal history is widely discussed in literature, but systematic assessment remains lacking for their magnitude, spatial distribution, and comparative analysis of different evaluation techniques. In this study we report the results of a systematic study of residual stresses in a 3D-printed double tower shaped samples using several approaches: the contour method, blind hole drilling laser speckle interferometry, X-ray diffraction, and Xe pFIB-DIC micro-ring-core milling analysis. We show that a high level of tensile and compressive residual stresses is inherited from SLM 3D-printing and retained for longer than 6 months. The stresses vary over a significant proportion of the material yield stress. All residual stress evaluation techniques considered returned comparable values of residual stresses even regardless of dramatically different dimensional scales from millimeters for the Contour Method down, laser speckle interferometry and XRD and down to small fractions of a mm (70 μm) for Xe pFIB-DIC ring-core drilling. The use of residual stress evaluation is discussed in the context of optimizing the printing strategy to enhance the mechanical performance and long-term durability.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Recent advancements in communication technology have catalyzed the widespread adoption of realistic content, with augmented reality (AR) emerging as a pivotal tool for seamlessly inte-grating virtual elements into real-world environments. In construction, architecture, and urban design, the integration of mixed reality (MR) technology enables rapid interior spatial mapping, providing clients with immersive experiences to envision their desires. The rapid advancement of MR devices, or devices that integrate MR capabilities, offers users numerous opportunities for enhanced entertainment experiences. However, to support designers at a high level of expertise, it is crucial to ensure the accuracy and reliability of the data provided by these devices. This study explores the potential of utilizing spatial mapping within various methodologies for surveying architectural interiors. The objective is to identify optimized spatial mapping procedures and determine the most effective applications for their use. Experiments were conducted to evaluate the interior survey performance, using HoloLens 2, iPhone 13 Pro for spatial mapping, and photogrammetry. The findings indicate that HoloLens 2 is most well-suited for the tasks exam-ined in the scope of experiments. Nonetheless, based on the acquired parameters, the author also proposes approaches to apply the other technologies in specific real-world scenarios.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from <5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

The manufacturing parameters influence the properties of thermo-mechanically processed met-als such as Mg alloys. This paper presents how the mechanical properties, the microstructure and the degradation rate of extruded Mn-containing Mg-Gd-alloys can be modified. Gd as repre-sented REE-element is particularly interesting due to the influence on the texture development in Mg and therefore studied as a base alloy system. The contents of Gd were investigated be-tween 2 to 9 wt.% with Mn-addition of 0.5 and 1.0 wt.%. The grain sizes and the corresponding textures were modified by the extrusion parameters and the alloy content. It was shown that modification by Mn can decrease the grain size, but increase the degree of recrystallization and decrease the degradation rate in the biological medium compared to the binary Mg-Gd system from previous studies. The results suggest that the binary Mg-Gd system can be produced more efficiently by adding Mn and that the resulting properties are more robust.

A series of Si-bearing MgAl₂O₄-spinels were synthesized at 1500-1650 °C and 3–6 GPa. These spinels had SiO₂ contents up to ~1.03 wt%, and showed a substitution mechanism of Si⁴⁺ + Mg²⁺ = 2Al³⁺. Unpolarized Raman spectra were collected from polished single grains, and displayed a set of well-defined Raman peaks at ~610, 823, 856 and 968 cm^-1 which had not been observed before. Aided with the Raman features of natural Si-free MgAl₂O₄-spinel, synthetic Si-free MgAl₂O₄-spinel, natural low quartz, synthetic coesite, synthetic stishovite and synthetic forsterite, we infer that these Raman peaks should belong to the SiO₄ groups. The relations between the Raman intensities and SiO₂ contents of the Si-bearing MgAl₂O₄-spinels suggest that at some P-T conditions some Si must adopt the M-site. Unlike the SiO₄ groups with very intense Raman signals, the SiO₆ groups are largely Raman-inactive. We have further found that the Si cations primarily appear on the T-site at P-T conditions ≤ ~3–4 GPa and 1500 °C, but attain a random distribution between the T-site and M-site at P-T conditions ≥ ~5–6 GPa and 1630–1650 °C. This Si-disordering process observed for the Si-bearing MgAl₂O₄-spinels hints that similar Si-disordering might happen to the (Mg,Fe)₂SiO₄-spinels (ringwoodite), the major phase in the lower part of the mantle transition zone of the Earth and the index mineral for the very strong shock stage experienced by extraterrestrial materials. The likely consequences have been explored.

Background: The management of erectile dysfunction (ED) shows several grey zones and new treatments for reduce the percentage of patients who discontinued the treatment are required. Here, we aim to evaluate the role of a natural mixture of named Icarifil (L-Citrulline, L-Carnitine, Eruca vesicaria, Panax ginseng, Tribulus terrestris, Turnera diffusa, Taurine, Vitamin E, Zinc) in the management of patients with ED. Methods: From September 2022 to March 2023, all patients attending 3 urological institutions due to ED were randomized to receive: Icarifil 1 sachet every 24 h (Group 1) or Icarifil 1 sachet + tadalafil 5 mg 1 tablet every 24 h (Group 2) or tadalafil 5 mg 1 tablet daily (Group 3), for 3 months. All patients underwent urologic visit and dedicated questionnaires (IIEF-5, SEP-2, SEP-3) at the enrollment and at the follow-up evaluation (3 months). Patient Reported Outcomes (PROs) at the follow-up evaluation were used. Primary endpoint was the difference in the questionnaires at the follow-up visit when compared with enrollment among the study groups. Results: In the per-protocol analysis, 52 patients in the Group 1, 55 in the Group 2 and 57 in Group 3 have been analyzed. At the follow-up evaluation, IIEF-5 have been improved in all the 3 Groups between enrollment and follow-up evaluation, but a statistically significant difference has been reported between Group 2 (+7.4) versus Group 1 (+4.1) or 3 (+5.1), (p<0.001; p<0.001). Moreover, 47 patients (94.0%) in the Group 2 showed an improvement in the SEP questionnaires, when compared with the baseline, while 29 in the Group 1 (56.9%) and 42 in the Group 3 (82.3%) with a statistically significant difference (p=0.004; p=0.003) among the Groups. The PROs analysis reported a better efficacy and patients’ satisfaction in Group 2 when compared with Group 1 or 3. Conclusions: In conclusion, Icarifil is able to improve penile erectile function in mild–moderate ED and it is able to significantly improve the clinical efficacy of tadalafil 5 mg daily use. Icarifil could be represent an interesting alternative treatment in patients experiencing adverse effects or with contraindications for chronic treatment with PDE5-is.

This review examines additive manufacturing for refractory tungsten (W) and its alloys. It emphasizes the primary challenges and determining factors involved in additive manufacturing pure W, W alloys, and composites. Our focus in this regard extends to both process and alloying strategies designed to address critical issues such as densification, micro-cracking, and mechanical properties in tungsten-based components produced through additive techniques. Throughout the review, we organize existing knowledge and insights into convenient tables, serving as valuable resources for researchers embarking on a deeper exploration of these topics.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

A complementary characterisation of the Al-alloy EN AW-5454 was carried out, intended for obtaining the laser hybrid welding parameters of sub-assemblies in the automotive industry. The investigation included a microstructural examination, and determination of the alloy's properties using several analytical methods (HV5 hardness measurement, tensile test, Charpy impact toughness, fracture mechanics analysis). Samples were prepared in the longitudinal and transverse directions of a cold-rolled sheet of EN AW-5454 with thicknesses of 3.5 mm and 4 mm. The measured hardness on the thinner sheet was 5% higher than on the thicker sheet. The tensile and yield strength were nominal, while the elongations were smaller by 2.2 - 3.2% for the longitudinal samples and by 2.7 - 13.7% for the transverse samples. The smaller deviations from the nominal values are for the thinner sheet metal. A precise topographical analysis showed brittle fractures of the samples. The Charpy impact toughness results on the thicker plate showed a 20% greater work needed to break it in the longitudinal direction than in the transverse direction. With the thinner sheet metal, 40% greater work was needed. SEM (Scanning Electron Microscope) analysis has shown that the intermetallic Al6(Mn,Fe) particles in the longitudinal samples were mostly intact, with evidence of tough areas on the upper part of the fracture, indicating a better toughness than the specimens in the transverse direction. More crushed intermetallic particles were observed at the fractures of the transverse samples, and their distribution appeared to be more oriented in the direction of rolling. Fracture mechanics SENB (single edge notch bending) tests and their analysis showed that the resistance of the material to crack propagation in the longitudinal sample was about 50% greater than that in the transverse sample. SEM analysis of the fractures showed that the state of the intermetallic particles in the fracture mechanics testing, and the fracture mechanism differed from the one in the Charpy fractures.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

Daptomycin is one of the last therapeutic resources for multidrug-resistant gram- positive bacteria. Despite its structural similarities with glycopeptides, its mechanisms of action and resistance are different, and in some respects are not completely understood. Mutations in several genes have been associated to daptomycin resistance, especially in mprF, walkR, rpoB and rpoC, but their role and importance remain to be elucidated. We have studied mutations in 11 genes, which have been previously associated to daptomycin non- susceptibility, in 9 daptomycin non-susceptible Staphylococcus aureus clinical isolates (daptomycin MIC: > 1mg/L). Susceptibility to daptomycin, vancomycin, linezolid, oxacillin, telavancin and dalbavancin were studied. walkR, agrA, cls1, cls2, fakA, pnpA, clpP, prs, rpoB, rpoC and mprF were amplified by PCR and sequenced. The sequences were compared with the S. aureus ATCC 25923 complete genome (GenBank gi: 685631213) by using BLAST® software. We did not find any changes in walkR, pnpA, prs and clpP. All isolates excepting isolate 5 showed a high number of significant mutations (between 13 and 25 amino acid changes) in mprF. Most isolates also showed mutations in rpo genes, cls genes and fakA. Daptomycin non-susceptibility in S. aureus clinical isolates seems to be reached through different mutations combinations when compared to S. aureus ATCC 25293. Especially mprF and cls1 showed a very high polymorphism in most isolates. Meanwhile, one isolate, St5, showed only single mutation in mprF (P314T).

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

Background: Telemonitoring systems in cardiology have shown potential in improving chronic cardiovascular disease (CVD) management. This study aims to evaluate the impact of telemonitoring, mainly through mobile applications, on patient outcomes such as self-care, blood pressure control, quality of life, and hospitalization. Methods: We systematically reviewed studies assessing telemonitoring methods for patients with chronic CVD. The analysis included studies from various geographic regions and healthcare settings, focusing on qualitative outcomes without performing a meta-analysis. Results: Telemonitoring was found to aid in maintaining blood pressure and significantly enhance self-care abilities. Improvements in quality of life were observed in some studies, though results varied. Most studies indicated telemonitoring could effectively manage blood pressure and reduce hypertension-related complications. However, the heterogeneity of interventions and outcomes measured across trials posed challenges for a comprehensive meta-analysis. Conclusions: Integrating telemonitoring systems into routine care can significantly improve disease management and patient outcomes for chronic CVD patients. Future research should standardize telemonitoring interventions and outcome measures, conduct long-term studies, and evaluate the cost-effectiveness of these systems. Greater blindness in future randomized controlled trials and more studies on atrial fibrillation are also necessary. Significant potential exists for telemonitoring to improve patient outcomes and assist in managing chronic illnesses.

Magnesium-silver alloys are of high interest for the use as temporary bone implants due to their antibacterial properties in addition to biocompatibility and biodegradability. Thin wires in particular can be used for scaffolding, but the determination of their degradation rate and homogeneity using traditional methods is difficult. Therefore, we have employed 3D imaging using X-ray near-field holotomography with sub-micrometer resolution to study the degradation of thin (250 μm diameter) Mg-2Ag and Mg-6Ag wires. The wires were studied in two states, recrystallized and solution annealed to assess the influence of Ag content and precipitates on the degradation. Imaging was employed after degradation in Dulbecco’s modified Eagle’s medium and 10% fetal bovine serum after 1 to 7 days. At 3 days of immersion the degradation rates of both alloys in both states were similar, but at 7 days higher silver content and solution annealing lead to decreased degradation rates. The opposite was observed for the pitting factor. Overall, the standard deviation of the determined parameters was high, owing to the relatively small field of view during imaging and high degradation inhomogeneity of the samples. Nevertheless, Mg-6Ag in the solution annealed state emerges as a potential material for thin wire manufacturing for implants.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Formation of Fe- and Mg-rich smectite and zeolite under alkaline conditions is concerned as secondary minerals after alkaline alteration of bentonite in a repository of radioactive wastes. It might be crucial for safety assessment whether smectite will be formed or not as secondary minerals after alkaline alteration of bentonite. In present paper, Fe- and Mg-rich smectite which are currently interacting with hyperalkaline groundwater was found at Narra in Palawan, Philippines. Mineralogical and geochemical investigation was conducted to understand formation process of smectite and factors determined secondary mineral species. Our study revealed a certain amount of smectite may have been produced under hyperalkaline conditions, altered from amorphous or poorly crystalline material such as M-S-H and F-S-H. Key factor which decides smectite or zeolite as secondary minerals after alkaline alteration of bentonite might be whether nuclei of M-S-H and/or F-S-H will be formed or not. This might be decided by the presence of dissolved Mg2+ and Fe2+ in the system. Our suggested formation process of smectite under alkaline conditions is analogue with generally-accepted model of smectite formation that might have been occurred on early Mars.

Pig farms management is involved in multiple factors such as environmental conditions, animal behavior, weight gaining and others. In all those scenarios, it is fundamental to detect each individual and its development as it grows to reach the shipment phase. Therefore, the objective of this study was to apply an automatic individual pig detection algorithm using Deep Learning Techniques, in frames taken from videos recorded during the weaning phase in real production conditions of small and medium producers in tropical conditions in Colombia. The weaning phase was selected because individual detection in each cage is more difficult due to environmental adaptations that piglets undergo after nursing. Piglets tend to cluster together during this phase, making image processing more challenging compared to the fattening phase, where animals are more isolated. The You Only Look Once (YOLOv7) algorithm and VGG Image Annotator were used to detect individuals in two pens separated by gender. All animal postures, lighting conditions were considered. The Precision, Recall and mAP metrics were used to assess the model performance with different confidence values. A precision of 98.3% in a threshold of 0.9 was reached, Recall of 98.5% in a threshold of 0.85. Data augmentation techniques were important to increase the dataset and to have a more realistic model for individuals’ detection. The method used allowed us to identify all the complete pigs’ bodies under different posture and lighting situations.

In the history, architects, engineers or artists traditionally visualized architectural, urban planning, urban design, or landscape design projects with physical models in a smaller scale to represent their ideas. The biggest problems of traditional materialistic models are the long production time and limitation of mobility. Thanks to advancements in digital technology, 3D models can now be generated easily from 2D blueprints using computer software. However, eventually the digitalized approach could not replace the whole industry of making physical models, because of a lack of stereoscopic 3D imaging of space and structures. In this study, we discuss two points: the normal procedure of visualizing 3D models in urbanism and architecture design projects; and proposal of the stereographic hologram visualization for 3D models created with CHIMERA hologram printer as a new approach to solve all the problems in spatial projects visualization of both digitalized and physical models. The experiment's results indicate that tabletop holograms' visualization quality can potentially replace traditional methods in the near future. Moreover, the input data for this method can be seamlessly integrated into current architectural and urban design workflows, making holograms a promising approach for 3D immersive content in this field.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

In this paper, we investigate various graphene monolayer nanomesh structures (diodes) formed only by nanoholes, with a diameter of just 20 nm and etched from the graphene layer in different shapes (such as rhombus, bow-tie, rectangle, trapezoid, and triangle), and their electrical properties targeting electromagnetic energy harvesting applications. In this respect, the main parameters characterizing any nonlinear device for energy harvesting are extracted from tens of measurements performed on a single chip containing the fabricated diodes. The best nano-perforated graphene structure is the triangle nanomesh one, which exhibits remarkable performance in terms of its characteristic parameters, i.e., a 420 Ω differential resistance for optimal impedance matching to an antenna, a high responsivity greater than 1000 V/W, and a low noise equivalent power of 847 pW/√Hz at 0 V.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Selection of the most suitable material is one of the key decisions to be taken at the design stage of a manufacturing process. Traditional approaches as Ashby maps based on material properties are widely used in the industry. However, in the production of multimaterial components, the criteria for the selection can include antagonistic approaches. The aim of this work is the implementation of a methodology based on the results of process simulations for several materials and classify them by applying an advanced data analytics method based on Machine Learning (ML), in this case the Support Vector Regression (SVR) and Multi-Criteria Decision Making (MCDM) methodolo-gies, in this case Multi-criteria Optimization and Compromise Solution (VIKOR) combined with Entropy weighting methods. In order to do this, a Finite Element Model (FEM) has been built to evaluate the extrusion force and the die wear in a multi-material co-extrusion process of bimetallic Ti6Al4V-AZ31B billets. After applying SVR and VIKOR combined with Entropy weighting methodologies, a comparison has been established based on the material selection and complexity of the methodology used, resulting that material chosen in both methodologies is very similar and MCDM method is easier to implement because there is no need of evaluate the error of the pre-diction model and the time for data preprocessing is less than the time needed in SVR.

Europium is the most-studied and least-well-understood rare earth ion (REI) dopant in GaN. While attempting to increase the efficiency of red GaN light-emitting diodes (LEDs) by implanting Eu⁺ into p-type GaN templates, the Strathclyde University group, in collaboration with IST Lisbon and Unipress Warsaw, discovered hysteretic photochromic switching (HPS) in the photoluminescence spectrum of doubly doped GaN(Mg):Eu. Our recent work, summarised in this contribution, has used time-, temperature- and light-induced changes in the Eu intra-4f shell emission spectrum to deduce the microscopic nature of the Mg-Eu defects that form in this material. As well as shedding light on the Mg acceptor in GaN, we propose a possible role for these emission centres in quantum information and computing.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

The effect of Mg particles on PLA's thermal, chemical, physical, and mechanical properties has been studied. The thermal and physical properties have been studied by differential scanning calorimetry, analysing the stability of the α and α’-crystals of the PLA. A colloidal route was used to introduce Mg particles inside the PLA matrix, ensuring a good dispersion of the particles. Materials with Mg contents from 0 to 10 wt.% have been prepared, with additions of polyethyleneimine (PEI) and polyethylene glycol (PEG). Fourier Transform Infrared Spectroscopy has been used to confirm the influence of Mg, PEI, and PEG on PLA properties. The mechanical properties have been measured with a universal tensile test machine on printed filaments via Fused Filament Fabrication (FFF), which were naturally aged to stable conditions. Filaments with and without a notch were studied to obtain the materials' tensile strength, elastic modulus, and fracture toughness. Different analytical models to explain the results of the PLA-Mg were studied, in which the interface strength of the PLA-Mg composites was calculated.

The conformational state of the activation loop (A-loop) is pivotal for the activation of most protein kinases. Hence, the characterization of the conformational dynamics of the A-loop is important to increase our understanding of the molecular processes related to diseases and to support the discovery of small molecule kinase inhibitors. Here, we carry out a combination of Molecular Dynamics (MD) and Essential Dynamics (ED) analyses to fully map the effects of phosphorylation, ADP, and conformation disrupting (CD) inhibitors (i.e., CD532 and MLN8054) on the dynamics of the A-loop of Aurora-A. MD revealed that the stability of the A-loop in an open conformation is enhanced by single phospho-Thr-288, while paradoxically, the presence of second phosphorylation at Thr-287 decreases such stability and renders the A-loop more fluctuant in time and space. Moreover, we found that such post-translational modification has a significant effect on the direction of A-loop motions. ED analysis suggests that the presence of the phosphate moiety induces the dynamics of Aurora-A to sample two distinct energy minima, instead of a single large minimum, as in unphosphorylated Aurora-A states. This suggests that the conformational distributions of Aurora-A with both single and double phospho-threonine modifications are remarkably different from the unphosphorylated state. In the closed states, binding of CD532 and MLN8054 inhibitors has the effect of increasing the distance of the N- and C-lobes of the kinase domain of Aurora-A, and the angle analysis between those two lobes during MD simulations showed that the N- and C-lobes are kept more open in presence of CD532, compared to MLN8054. As the A-loop is a common feature of Aurora protein kinases, our studies provide a general description of the conformational dynamics of this structure upon phosphorylation and different ligands binding.

Biomineralization has become a research hotspot and attracted widespread attention in the field of carbonate sedimentology. In this study, Bacillus licheniformis DB1-9 was used to induce the calcium carbonate precipitation at different magnesium calcium molar ratios in the laboratory to further explore the biomineralization mechanism. Phylogenetic tree shows that the bacteria belongs to Bacillus licheniformis species. The ammonia and carbonic anhydrase can be released by this bacteria, resulting in the pH increase, and the carbonic anhydrase can also promote the hydration reaction of carbon dioxide and subsequently produce the bicarbonate and carbonate ions to elevate the supersaturation of calcium carbonate in the liquid culture medium to facilitate the precipitation of carbonate minerals. The calcites have a shape of rhombohedron, dumbell, and elongation, and aragonite often appears in the form of mineral aggregates, besides that there are also the spherical and the fusiform minerals. FTIR result shows there are some organic functional groups, such as C-O-C and C=O, beside of the characteristic peaks of the calcite and the aragonite, indicating that microbial metabolism is closely related to the mineral formation. The superthin slices of the bacteria analyzed by HRTEM, SAED, EDS and STEM show that the surface and EPS can adsorb a large number of calcium ions and magnesium ions and EPS may act as the nucleation sites, what’s more, the intracellular nanometer-scale sphere areas show the amorphous structures, and the intracellular calcium ions and magnesium ions suggeste that they can be transported from the outside to inside the cell by diffusion along the concentration grade from high to low. This study may provide some references to further understand the biomineralization mechanism induced by microorganisms in the laboratory and the field, and also helps to explore the reason of the transition of calcite sea to aragonite sea in the geological history.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

An analysis of the processes of plastic deformation and acoustic relaxation in a high-entropy alloy Al0.5CoCrCuFeNi was carried out. The following have been established: dominant dislocation defects; types of barriers that prevent the movement of dislocations; mechanisms of thermally activated movement of various elements of dislocation lines through barriers at room and low temperatures. Based on modern dislocation theory, quantitative estimates have been obtained for the most important characteristics of dislocations and their interaction with barriers.

A new model of gravity is presented here similar to the earlier work of Verlinde on Emergent Gravity but without the use of Verlinde's main assumption on the nature of gravity as an entropic force using the First Law of Thermodynamics. Instead, the model will be shown to be consistent with the Second Law of Thermodynamics as used in Black Hole Physics. Moreover, it does not use the Equipartition Theorem such that there is no need to define a thermal bath enclosed within a holographic screen. The theory uses $E=NE_{p}$, for the total energy of a massive object where $E_{p}$ is the Planck Energy while $N$ is the number of Planck Energy to represent the maximum possible density of information that can reside in matter. The theory uses also the Holographic Principle as the basis for an information-theoretic approach to the nature of gravity. It is shown here that gravity emerges whenever there is an updating of the information within a given volume of space by the presence of matter.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Staphylococcus aureus is a Gram-positive bacterium causing a range of mild to life-threatening infections including bone infections such as osteomyelitis. S. aureus is able to invade and persist within non-professional phagocytic cells such as osteoblasts. In the present study four different S. aureus strains, 2SA-ST239-III, 5SA-ST5-II, 10SA-ST228-I, and 14SA-ST22-IVh were tested for their ability to modulate cell viability in MG-63 osteoblast-like cells following a successful invasion and persistence. Methicillin-sensitive S. aureus (MSSA) ATCC-12598-ST30 was used as control. Despite the demonstrated similar abilities of internalization and persistence of ATCC-12598-ST30, 2SA-ST239-III, and 14SA-ST22-IVh strains in MG-63 osteoblast-like cells under our experimental conditions, we demonstrated that the decrease in cell viability was due to the different behavior of the considered strains, with the number of intracellular bacteria playing a limited role. We focused our attention on different cellular biochemical functions related to inflammation, cell metabolism, and oxidative stress during osteoblast infections. We were able to show that: 1) ATCC-12598-ST30 and 2SA-ST239-III were the only two clones able to persist and maintain their number into the cellular hostile environment during the entire period of infection; 2) 2SA-ST239-III was the only clone able to significantly increase the gene expression (3 and 24 h) and protein secretion (24 h) of both interleukin-6 (IL-6) and tumor necrosis factor alpha (TNF-α) in MG-63 osteoblast-like cells; 3) the same clone determined a significant up-regulation of transforming growth factor-β1 (TGF-β1) and the metabolic marker glyceraldehyde 3-phosphate dehydrogenase (GAPDH) mRNAs at 24 h post infection; 3) neither the MSSA nor the four MRSA strains induced oxidative stress phenomena in MG-63 cells, although a very different expression pattern towards nuclear factor E2-related factor 2 (Nrf2) and its downstream gene heme oxygenase 1 (HO-1) activation was observed among the different clones. Our results can open a new way of considering therapies, going in the direction of an individualized therapeutic strategy that should take into account the difference existing between MSSA and MRSA as well as the distinctive features of the different clones. Not only, therefore, a different antibiotic approach but also a starting point for considering different host factors, i.e. the modulation of specific cytokines such as IL-6, TNF-α, and TGF-β1.

This study presents extended Immunity Agent-Based Model (IABM) simulations to evaluate vaccination strategies in controlling the spread of infectious diseases. The application of IABM in the analysis of vaccination configurations is innovative, as a vaccinated individual can be infected depending on how their immune system acts against the invading pathogen, without a pre-established infection rate. Analysis at the microscopic level demonstrates the impact of vaccination on individual immune responses and infection outcomes, providing a more realistic representation of how the humoral response caused by vaccination affects the individual’s immune defense. At the macroscopic level, the effects of different population-wide vaccination strategies are explored, including random vaccination, targeted vaccination of specific demographic groups, and spatially focused vaccination. The results indicate that increased vaccination rates are correlated with decreased infection and mortality rates, highlighting the importance of achieving herd immunity. Furthermore, strategies focused on vulnerable populations or densely populated regions prove to be more effective in reducing disease transmission compared to randomly distributed vaccination. The results presented in this work show that vaccination strategies focused on highly crowded regions are more efficient in controlling epidemics and outbreaks. Results suggest that applying vaccination only in the densest region resulted in the suppression of infection in that region, with less intense viral spread in areas with lower population densities. Strategies focused on specific regions, in addition to being more efficient in reducing the number of infected and dead people, reduce costs related to transportation, storage, and distribution of doses compared to the random vaccination strategy. Considering that, despite scientific efforts to consolidate the use of mass vaccination, the accessibility, affordability, and acceptability of vaccines are problems that persist, investing in the study of strategies that mitigate such issues is crucial in the development and application of government policies that make immunization systems more efficient and robust.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Heat-treated aluminum-silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys due to their ability to remove the need for costly heat treatments. Since the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of a near eutectic Al-Ce alloy with additions of Ni and Mn. The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. SEM coupled with EDS and DSC techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase is present at higher cooling rates. At lower cooling rates, near the center of the casting, a proeutectic Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 at. % of Mn was dissolved in this proeutectic Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples' liquidus temperatures which is indicative of compositional variations. Inductively coupled plasma atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences to phase formation, which agreed with the SEM and DSC results. This experimentation provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

Butyric acid as a histone deacetylase (HDAC) inhibitor was produced by a number of periodontal and root canal microorganisms (such as Porphyromonas, Fusobacterium etc.). Butyric acid may affect the biological activities of periodontal/periapical cells such as osteoblasts, periodontal ligament cells etc., and thus affect periodontal/periapical tissue destruction and healing. The purposes of this study were to study the toxic effects of butyrate on matrix and mineralization markers’ expression of MG-63 osteoblasts. Cell viability and proliferation were determined by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay. Cellular apoptosis and necrosis were analyzed by propidium iodide/Annexin V flow cytometry. Protein and mRNA expression of OPG, and RANKL were analyzed by western blotting and RT-PCR. OPG, soluble RANKL (sRANKL), 8-isoprostane, pro-collagen I, MMP-2, osteonectin (SPARC), osteocalcin and osteopontin secretion into culture medium were measured by enzyme-linked immunosorbant assay. Histone H3 acetylation levels were evaluated by immunofluorescent staining (IF) and western blot. We found that butyrate induced morphologic changes of growing MG-63 cells, with bigger and flattened in appearance. Butyrate activated histone H3 acetylation of MG-63 cells. Exposure of MG-63 cells to butyrate partly decreased cell number with no marked increase in apoptosis and necrosis. Butyrate stimulated RANKL protein expression, whereas it inhibited OPG protein expression. Butyrate also inhibited the secretion of OPG in MG-63 cells, whereas sRANKL level was below detection limit. Butyrate stimulated 8-isoprostane, MMP-2 and osteopontin secretion, but not procollagen I, osteonectin, osteocalcin in MG-63 cells. In conclusion, butyric acid generated by periodontal and root canal microorganisms may potentially induce bony destruction and impair bone repair by alteration of OPG/RANKL expression/secretion, 8-isoprostane, MMP-2, and osteopontin secretion, and affect cell proliferation. These effects are possibly related to increased histone acetylation. These events are important in the pathogenesis of periodontal and periapical destruction.

Fexuprazan is a potassium-competitive acid blocker approved for treating gastric acid-related diseases. Herein, we evaluated the pharmacokinetics (PKs) of single-dose and multiple-dose oral administration of fexuprazan 10 mg tablets in healthy subjects (Part 1) and investigated the bioequivalence between fexuprazan 10 mg and 40 mg tablets (Part 2). Part 1 comprised a single- and multiple-dose, 1-sequence, and 2-period design, and Part 2 comprised a single-dose, 2×2 crossover design. Eight and 23 subjects completed Parts 1 and 2, respectively. In Part 1, multiple doses accumulated twice as much as single doses. In Part 2, the geometric mean ratios [90% confidence intervals] for maximum plasma concentration (Cmax) and area under the concentration–time curve from zero to the time of the last quantifiable concentration (AUClast) of four fexuprazan 10 mg tablets to those of one fexuprazan 40 mg tablet were 1.0290 (0.9352–1.1321) and 1.0290 (0.9476–1.1174), respectively, which met bioequivalence criteria. Overall, favorable PK was observed after single and multiple administrations of one fexuprazan 10 mg tablet, and four fexuprazan 10 mg tablets were pharmacokinetically equivalent to one fexuprazan 40 mg tablet.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

Structural and functional materials are subjected to harsh oxidizing environments that lead to a rapid decline in their surface chemical stability. At high-temperatures, the diffusion of atoms is erratic; thus, the reactive elements (REs) get a chance to migrate to the surface and look for oxygen-reactive sites. Their migration from the lattice sites creates vacancies in the matrix and thus weakens the bond, making the material prone to environmental degrading factors. Subsequently, the inward diffusion of oxygen, sulfur, nitrogen, or carbon may occupy these vacancies, resulting in undesired precipitation at the grain boundary, which is usually brittle. The solubility and dissociation of attacking species and corrosion products play the most critical role in corrosion in high-temperature water. To evade such situations, Ti, Al, and Cr are added in Ni/Fe-based alloys, forming a dense oxide layer on the surface that impedes further surface migration of ions. The stability of the alloys is then determined by the capability of these oxide layers to heal or reform during spalling/cracking. This review attempts to understand the migration of REs at the interfaces to prepare structural materials in any unexpected set of oxidizing service conditions. This review will also try to establish the interaction mechanism of REs novel/conventionally added in the alloys with the oxidizing elements in the environments to design better degradation-resistant high-temperature alloys.

The bulk planetary compositions are thought to be linked to the chemical abundances of their host stars. The abundances of 8 key rock-forming elements and the key planetary abundance ratios in G– and F–type main sequence stars located in the Solar neighborhood within 50 pc were statistically analyzed. The averaged C/O, Mg/Si, and Fe/Si elemental ratios of the planetary systems have a crucial role in the chemical composition and the mineralogy of a rocky planet's interior. We also studied the variation of the calculated Ca/Si, Al/Si, Na/Si and Fe/Si ratios in the samples of the examined stars using the Ca, Al, Na, and Fe abundances from the catalog and then attempt to constitute plausible occurrence trends of the analyzed abundance ratios for the rocky planet population in the near – solar galactocentric distances. Considering these results, we provide simple predictions for the most likely bulk compositions of the potential rocky planets. We further apply our results to compare them to the solar averaged abundance ratios, finding that the key elemental ratios for rocky planet composition in the Solar System are not typical amongst most of the studied stellar samples.

Chenodeoxycholic acid (CA) is a naturally occurring bile acid that is produced in the liver from cholesterol. Three CA complexes using Zn(II), Mg(II), and Ca(II) ions were synthesized to examine the chelation tendencies of CA towards these metal ions. The complexation reaction of CA with the metal ions under investigation was conducted with a 1:1 molar ratio (CA to metal) at 60-70°C in natural media (pH 7-8), which consisted of a binary solvent of MeOH and H2O (1:1). The resulting CA complexes were characterized using analytical data (metal, H, C, and Cl, analysis) and spectral data (UV-visible, FT-IR, and 1H NMR) to elucidate the complexes’ structures. The results suggested that CA in anion form utilized oxygen atoms of the carboxylate group (-COO−) to capture Zn(II), Mg(II), and Ca(II) ions. This produced complexes with the general compositions of [Zn(CA)(H2O)Cl], [Mg(CA)(H2O)Cl]H2O, and [Ca(CA)(H2O)Cl]2H2O, respectively. The Kirby-Bauer disc diffusion assay was then used to explore the bioactivity of the CA complexes toward three fungal species, three Gram-positive bacteria, and two Gram-negative bacteria. The Ca(II) and Mg(II) complexes exhibited marked inhibitory effects on the cell growth of the fungal species Aspergillus niger with potency equal to 127% and 116% of the activity of the positive control, respectively. The Zn(II) and Ca(II) complexes strongly inhibited the growth of Penicillium sp., while the Zn(II) and Mg(II) complexes showed strong growth inhibition towards the Gram-negative species Pseudomonas aeruginosa.

Visceral leishmaniasis is a disease caused by protozoa of the species Leishmania (Leishmania) infantum (syn=Leishmania chagasi) and Leishmania (Leishmania) donovani, which are transmitted by hematophagous in-sects of the genera Lutzomyia and Phlebotomus. The domestic dog (Canis familiaris) is considered the main ur-ban reservoir of the parasite due to the high parasite load on its skin, serving as a source of infection for sand-fly vectors and, consequently, perpetuating the disease in the urban environment. Some factors are consid-ered important in the perpetuation and spread of canine visceral leishmaniasis (CVL) in urban areas, such as stray dogs with their errant behavior and houses that have backyards with trees, shade, and organic materi-als, creating an attractive environment for sandfly vectors. CVL is found in approximately 50 countries with the number of infected dogs reaching millions and, due to the difficulty of controlling and diagnosing the disease, the number of infected animals could be even greater. In the four continents endemic for CVL there are reports of disease expansion in endemic countries such as Brazil, Italy, Morocco, and Tunisia, as well as in areas where CVL is not endemic, for example, Uruguay. Socio-environmental factors, such as migration, drought, deforestation, and global warming, have been pointed out as one of the reasons for expansion to ar-eas where it had been absent. Thus, the objective of this review is to address (i) the distribution of CVL in endemic areas (ii) the role of the dog in the visceral leishmaniasis epidemiology and the factors that influence dog infection and spread of the disease, and (iii) the challenges faced in the control of CVL.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

To obtain high quality grain refiner, a new Al-5Ti-1B-1RE master alloy grain refiner was synthesised by melt-matching method. Thermodynamic calculations and kinetic analyses, which were seriously missing from the study of key issues during the preparation process, were investigated. The microstructure and properties, comparison of the refining effect of different grain refiners on industrial pure aluminium and its refining mechanism were analysed with the help of X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM) and energy spectroscopy, transmission electron microscopy (TEM) and an electronic universal testing machine (CSS-44100). The experimental results show that the second-phase particles in the Al-5Ti-1B-1RE master alloy matrix synthesised by the melt-matching method are mainly TiB2、 A13Ti、Ti2A120RE, etc. The magnitude of the free energy ΔG of the synthesis reaction is calculated to be ΔGTiB2<ΔGAl3Ti<ΔGTi2A120RE. When the temperature is low (undercooling ΔT is large), the nucleation rate N mainly depends on the kinetic atomic diffusion activation energy Q, while the thermodynamic nucleation work becomes a secondary factor, and vice versa. The industrial pure aluminum refined by the new grain refiner has almost transformed from coarse columnar crystals to fine equiaxed crystals, with an average grain size of 70.2 μm, which was 36.18% and 20.66% smaller than that refined by domestic and imported Al-Ti-B wire master alloy grain refiner, and its mechanical properties of tensile strength σb was increased by 11.94%, 8.29%, and elongation at break δ was improved by 31.79%, 17.41%, respectively. The main mechanism for refining pure aluminum in Al-5Ti-1B-1RE master alloy is the formation of TiA13 on TiB2 particles, the release of RE atoms from Ti2A120RE phase surrounding TiAl3, and the partial transformation into TiA13 phase, which promotes the dual nucleation refinement mechanism and the pinning effect of rare earth elements on grain boundaries.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

Seeds represent the major source of food protein, impacting on both human nutrition and animal feeding. Therefore, seed quality needs to be appropriately addressed in the context of viability and food safety. Indeed, long-term and inappropriate storage of seeds might result in enhancement of protein glycation, which might affect their quality and longevity. Glycation of seed proteins can be probed by exhaustive acid hydrolysis and quantification of the glycation adduct N^ɛ-(carboxymethyl)lysine (CML) by liquid chromatography-mass spectrometry (LC-MS). This approach, however, does not allow analysis of thermally and chemically labile glycation adducts, like glyoxal-, methylglyoxal- and 3-deoxyglucosone-derived hydroimidazolones. Although enzymatic hydrolysis might be a good solution in this context, it requires aqueous conditions, which cannot ensure reconstitution of seed protein isolates. Because of this, the complete profiles of seed AGEs are not characterized so far. Therefore, here we propose the approach, giving access to quantitative solubilization of seed proteins in presence of sodium dodecyl sulfate (SDS) and their quantitative enzymatic hydrolysis prior to removal of SDS by reversed phase solid phase extraction (RP-SPE). Using MG-H1 as a case example, we demonstrate the applicability of this method for reliable and sensitive LC-MS-based quantification of chemically labile AGEs and its compatibility with bioassays.

The rural population in the Dry Zone of Sri Lanka is largely affected by Chronic Kidney Disease of Unknown etiology (CKDu). According to the multidisciplinary research carried out so far, quality of groundwater was considered one of the possible causative factors for CKDu. Therefore, the assessment of water quality variations and evolution mechanism of water quality parameters of drinking water sources is important for identifying any relationships between CKDu and the drinking water quality. The current study aimed to perform a detailed hydrogeochemical investigation using isotopic and chemical methods on selected groundwater sources in the CKDu-endemic, non-endemic and control areas. TDS, hardness, Mg2+, Na+ and F- are the main parameters that cause water quality deterioration but, their derived mechanism in these three regions are completely different. The excess concentrations of F- and Mg2+ in the CKDu endemic area, low F- and high Mg2+in the CKDu non-endemic sedimentary formation, and either combinations of low F- and low Mg2+, high F- and low Mg2+ or low F- with high Mg2+ in the control area are the distinct features. The primary processes that regulate the evolution of groundwater types in CKDu endemic and control area is the weathering of silicates. Similarly, in the CKDu endemic area, carbonate dissolution and reverse ion exchange are prominent. Cation exchange and evaporite dissolution are more pronounced in the control area. Shallow groundwaters are evapo-concentrated hence it further deteriorates quality when compared to the deep groundwater with non-mixed, non-evaporated, and higher elevation recharge effect (from 100 m altitude) in the CKDu endemic area. Dilution decreases the ion content in the CKDu endemic area while evaporite dissolution further increase it in the control area after the rainy season. Evaporation, and seawater mixing affected the quality of groundwater in the non-endemic sedimentary formation. A statistically significant difference of F- ionic ratio with Na+, Mg2+, Ca2+ in the endemic and control areas. Intense rock weathering combined with the desorption added excess F- to the groundwater in the CKDu endemic area while the cation exchange and fluorite dissolution is contributing factor in CKDu control area. All the groundwater samples analyzed have exceeded the moderate hardness threshold. However, prominent Mg hardness proportion together with excess F- in the CKDu endemic area may produce nephrotoxic MgF2 complexes that may trigger renal damage. In contrast, produced NaF complexes in the CKDu control area leads to reduction of F- toxicity in the human body. Therefore, increased levels of magnesium, fluoride and TDS in the shallow groundwater, along with geochemical, hydrogeological and climatic factors, may contribute to the CKDu in the Dry Zone of Sri Lanka.

In the context of restorative dentistry and the use of different techniques and dental adhesive systems, this study was to designed to assess the degree of adhesive absorption and wetting for each dental micro applicator; and also quantify the amount of lost fiber flocks after three applications of dental adhesive on the inside surface of a plastic veneer tooth in order to reveal a potential contaminating factor at the adhesive interface. Initially, one drop of dental adhesive was dispensed into a glass dental mixing well. The dental adhesive was then applied onto the inside surface of the veneer restoration for 30s using a dental micro applicator which was weighed afterwards. For each dental micro applicator, this sequence was repeated three times and measured again by the same operator. Each adhesive application was analyzed separately, to show the values independently and compare them to the initial weight. The samples of Fiber-Free Elastomer Bristle Micro Applicators (FEBM) demonstrated the best performance with a good degree of absorption and wetting of the dental adhesive without the loss fiber flocks and release-induced weight loss. The samples of Conventional Fiber Flocked Micro Applicators (CFFM) demonstrated good initial absorption and wetting of the dental adhesive, but visually shed several fiber flocks which resulted in significant weight loss and can also be considered a contaminating factor at the adhesive interface.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

The objective of this study was to evaluate the occurrence of Clostridium perfringens in stool samples and swabs collected from wild mammals in the Amazon biome. Sixty-five faecal and swab samples were collected in situ and ex situ from 16 species and three genera of wild mammals, some of which were in good health and some of which had diarrhoea. After pre-enrichment, the samples were plated on selective agar for C. perfringens. Characteristic colonies were subjected to multiplex PCR for the detection of genes encoding the main C. perfringens toxins (alpha, beta, epsilon, and iota toxin and enterotoxin). Among the 65 samples, 40 (61.5%) were positive for the gene encoding the alpha toxin and were classified as type A. Faecal samples were more than four times more likely to be positive for C. perfringens than were swab samples. No other toxinotypes were found. The findings of this study suggest that C. perfringens type A is commonly found as a commensal in mammal species of the Amazon biome. This seems to be the first study to identify C. perfringens type A in species such as B. variegatus (common ground sloth), C. didactylus (two-toed sloth), P. flavus (Jupará), T. tetradactyla (anteater), S. collinsi (squirrel monkey), S. niger (black marmoset), and S. apella (Guyana capuchin) and in the genus Didelphis sp. (opossum).

The corrosion inhibition effects of Drimia maritima (L.) Stearn sin. Urginea matima (L.) Backer on three different materials, i.e. as-cast Al-7 wt.% Si alloy, SAE 1020 low carbon steel and commercially pure Al samples, into a stagnant and naturally aerated 0.5 M NaCl solution are evaluated. For this purpose, both the potentiodynamic polarization curves and electrochemical impedance spectroscopy with equivalent circuit are utilized. It is found that inhibition effect in-creases up to certain minor Drimia maritima content. Adsorption isotherms (e.g. Langmuir and Temkin) have indicated that all three examined material comprise physical adsorption mecha-nism. Al-Si alloys have attained inhibition efficiency of about 96% at 25 oC with 1250 ppm of Drimia maritima, and ~43% with 625 ppm at 45 oC. On the other hand, the cp. Al and SAE 1020 samples attain ~ 89% and 68% with 1250 ppm and 500 ppm at 25 oC, respectively. This clearly in-dicates that the dosage of Drimia maritima green inhibitor into NaCl solution posses certain sus-ceptibility for each distinctive material examined. Impedance parameters obtained by using CNLS (complex non-linear least squares simulations) are correlated and discussed.