Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Based on three-dimensional optical proximity correction (3D OPC), recent advancements in 3D lithography have enabled the high-fidelity customization of 3D micro-optical elements. However, micron-to-millimeter scale structures represented by Fresnel lens design bring more stringent requirements for 3D OPC, which poses significant challenges to the accuracy of models and the efficiency of algorithms. Thus, a lithographic model based on optical imaging and photo-chemical reaction curve is developed in this paper, and a sub-domain division method with a statistics principle is proposed to improve the efficiency and accuracy of 3D OPC. Both the simulation and the experimental results showed the superiority of the proposed 3D OPC method in the fabrication of the Fresnel lenses. The computation memory requirements of the 3D OPC are reduced to below 1 %, and the profile error of the fabricated Fresnel lens reduced 79.98%. Applying the Fresnel lenses to an imaging system, the average peak signal to noise ratio (PSNR) of the image increased by 18.92 %, and the average contrast of the image enhanced by 36 %. We believe the proposed 3D OPC method can be extended to the fabrication of vision-correcting ophthalmological lenses.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.

The domestic ducks (Anas platyrhynchos domesticus) are resistant to most of the highly pathogenic avian influenza virus (HPAIV) infections. In this study, we characterized the lung proteome and phosphoproteome of ducks infected with HPAI H5N1 virus (A/duck/India/02CA10/2011/Agartala) at 12 hr, 48 hr and 5 days post infection condition. Total 2082 proteins were differentially expressed and 320 phosphorylation sites mapping to 199 phosphopeptides corresponding to 129 proteins were identified. Functional annotation of proteome data analysis reveals activation of RIG-I-like receptor and Jak-STAT signaling pathways, that lead to induction of interferon stimulated genes (ISGs) expression. The pathway analysis of phosphoproteome datasets also confirms the activation of RIG I, Jak-STAT signaling, NF-kappa B signaling and MAPK signaling pathways in the lung tissues. The induction of ISGs proteins (STAT1, STAT3, STAT5B, STAT6, IFIT5 and PKR) establishes protective antiviral immune response in duck lung tissue. Further, the protein-protein interaction network analysis identified proteins like AKT1, STAT3, JAK2, RAC1, STAT1, PTPN11, RPS27A, NFKB1 and MAPK1 as main hub proteins that might play important roles in disease progression in ducks. Together, functional annotation of proteome and phosphoproteome datasets reveals the molecular basis of the disease progression and disease resistance mechanism in ducks infected with HPAI H5N1 virus.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

This article provides an overview of multi-fidelity modeling trends. Fidelity in modeling refers to the level of detail and accuracy provided by a predictive model or simulation. Generally, models with higher fidelity deliver more precise results but demand greater computational resources. Multi-fidelity models integrate high-fidelity and low-fidelity models to obtain fast yet accurate predictions. Their growing popularity is due to their ability to approximate high-fidelity models with high accuracy and low computational cost. This work classifies publications in multi-fidelity modeling based on various factors, including application, surrogate selection, fidelity difference, fidelity combination method, field of application, and year of publication. The study also examines the techniques used to combine fidelities, focusing on multi-fidelity surrogate models. To accurately evaluate the advantages of utilizing multi-fidelity models, it is necessary to report the achieved time savings. This paper includes guidelines for authors to present their multi-fidelity-related savings in a standard, succinct, yet thorough way to guide future users. According to a select group of publications that provided sufficient information, multi-fidelity models achieved savings of up to 90% while maintaining the desired level of accuracy. However, the savings achieved through multi-fidelity models depend highly on the problem.

The present paper proposes an accurate characterization of a NACA 23012 airfoil at near stall conditions at a Reynolds number $Re=3\cdot 10^5$. In light of the unavoidable limits of which experiments suffer near the stall regime both in terms of effective two--dimensionality and data portability across different research groups, the present characterization is performed through high fidelity numerical simulations. Taking advantage of the local discontinuous Galerkin (LDG) LES solver, implemented in the open source library \textit{FEMilaro}, the airfoil behavior is investigated ranging from $\alpha=5^{\circ}$ to $17^{\circ}$, with a peculiar focus for $\alpha \ge 10^{\circ}$. Accuracy of the found results is ensured both from the realistic and accurate reconstructed flow physics and by means of a proper comparison with existing experimental data. Then, a reliable numerical baseline is obtained for any future investigation involving a NACA 23012 airfoil at $Re=3 \cdot 10^5$. The future study of the actual research group will be a parallel BVI analysis, but results are completely extendable as they are to any other research.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

The coronaviral pandemic has led to a shift in traditional teaching methods to more innovative approaches, such as high-fidelity patient simulation (HFPS), which can improve students’ clinical judgement and decision-making for quality patient care. A modified guideline was introduced to enhance students’ satisfaction and self-confidence in learning through HFPS. The study involved 189 baccalaureate nursing students, with 92 in the intervention group and 97 in the control group. The intervention group received the modified HFPS guideline, while the control group received standard treatment with basic instruction. After the HFPS debriefing session, students provided narrative feedback on their learning experience. The quantitative results showed that students in the intervention group reported a significant improvement in satisfaction and self-confidence in learning compared to the control group. The modified HFPS guideline provided clear guidance for students to learn and apply knowledge and skills more effectively, leading to increased engagement during interactive simulation sessions. The results suggest that the HFPS guideline should be added to the curriculum to enhance students’ satisfaction and self-confidence in learning, even in junior students. Innovative teaching methods, such as HFPS, can be necessary and beneficial for healthcare professional training, after the pandemic.

High-fidelity patient simulation (HFPS) is widely used in professional training to enhance students’ competence in clinical management. Problem-solving (PS) and clinical reasoning (CR) skills are essential to developing students in professional competence in safe and effective care. These two skills should be initiated at the early training. However, little is known about the effects of HFPS on developing PS and CR skills in first year undergraduate students. Therefore, this pre- and post-experimental study aimed to investigate the effects of HFPS on development of PS and CR skills in first-year nursing students. The students were required to go through four sessions, preparation, pre-briefing and orientation, simulation role-playing, and debriefing, for the HFPS. The study utilized the Problem-Solving Inventory (PSI) and the Nurses Clinical Reasoning Scale (NCRS) to measure problem-solving and clinical reasoning abilities before and after HFPS. Bivariate analysis, one-sample t-test, and independent t-test were performed to evaluate the performance of the PS and CR skills at the two study periods. One hundred eighty-nine students were recruited, with a mean age of 20.56 years, and 73% were female students. The analytic results showed that the PSI, particularly in domains of Problem-Solving Confidence (PSC) (p<0.001) and overall PS (p<0.001), and the CR (p<0.001) had significant improvement after HFPS. The study concluded that HFPS is an effective innovative method to significantly improve students’ problem-solving and clinical reasoning abilities. Nurse educators play an important role in providing explicit learning instructions in a simulation guideline that directs and guides students to learn at each stage of HFPS. Students should take more initiative and engage in their learning through HFPS to enhance their competence in knowledge and higher intellectual skills for personal and professional developments.

Artificial intelligence (AI) driven language models have seen a rapid rise in development, deployment, and adoption over the last few years. This surge has sparked many discussions about their societal and political impact, including political bias. Bias is a crucial topic in the context of large models due to its far-reaching consequences on technology, politics, and society. It significantly influences public perception, decision-making, political discourse, and AI policy governance and ethics. This study investigates political bias through a comparative analysis of four prominent AI models: ChatGPT-4, Perplexity, Google Gemini, and Claude.Through a comprehensive analysis by systematically and categorically evaluating their responses to politically and ideologically charged tests and prompts, utilizing the Pew Research Center’s Political Typology Quiz, the Political Compass assessment, and ISideWith political party quiz, this study identifies significant ideological leanings and the nature of political bias within these models. The findings revealed that ChatGPT-4 and Claude exhibit a liberal bias, Perplexity is more conservative, while Google Gemini adopts more centrist stances. The presence of such biases underscores the critical need for transparency in AI development and the incorporation of diverse training datasets, regular audits, and user education to mitigate these biases. This analysis also advocates for more robust practices and comprehensive frameworks to assess and reduce political bias in AI, ensuring these technologies contribute positively to society and support informed, balanced, and inclusive public discourse, which will point towards neutrality.The results of this study add to the ongoing discourse about the ethical implications and development of AI models, highlighting the critical need to build trust and integrity in AI models. Additionally, future research directions have been outlined to explore and address the complex issue of bias in AI.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

The management of brain tumors presents numerous challenges, despite the employment of multimodal therapies including surgical intervention, radiotherapy, chemotherapy, and immunotherapy. Owing to the distinct location of brain tumors and the presence of the blood-brain barrier (BBB), these tumors exhibit considerable heterogeneity and invasiveness at a histological level. Recent advancements in hydrogel research for the local treatment of brain tumors have sought to overcome the primary challenge of delivering therapeutics past the BBB, thereby ensuring efficient accumulation within brain tumor tissues. This article elaborates on various hydrogel-based delivery vectors, examining their efficacy in the local treatment of brain tumors. Additionally, it reviews the fundamental principles involved in designing intelligent hydrogels that can circumvent the BBB and penetrate larger tumor areas, thereby facilitating precise, controlled drug release. Hydrogel-based drug delivery systems (DDSs) are posited to offer a groundbreaking approach in addressing the challenges and limitations inherent in traditional oncological therapies, which are significantly impeded by the unique structural and pathological characteristics of brain tumors.

Soccer is the leading cause of all sports-related ocular injuries in Europe and Israel and leads to blindness at a disproportionately high rate, especially among children (Thompson et al., 2019). With soccer being the most popular sport in the world, it is surprising the only solution to ocular injuries are sports glasses which can cause direct damage to the eye and impair peripheral vision by 15%, calling for an alternative (Smith & Jones, 2020). This work, based on an imported facial model, focuses on both the qualitative and quantitative aspects of building a personalized, low-cost (through optimizing material needed), superior apparatus to conventional sports glasses. The quantitative side examines a modified and model-validated (through a SRS of thirty unique extrapolated points) multivariate linear regression equation, based on horizontal and vertical rotation angles (n=60) trained with residual and computer simulation data, that can accurately extrapolate and quantify ocular impact from all horizontal and vertical rotation angles and a modified Hertzian Contact Stress Equation to determine the thickness of the apparatus using the elasticity modulus, impact force, and geometrical facial and soccer-ball features. The qualitative side examines where firstly, ocular impact is most prevalent, and secondly, where most impact is seen from rotating the ball horizontally and vertically through analysis of Pearson’s Correlation Coefficient at the supraorbital, medial canthus, infraorbital, and lateral canthus regions from both regression equations as well as a cost-benefit analysis for comparison with conventional sports glasses. The findings discovered in this work lay the groundwork for future research to build a customized low-cost ocular injury prevention device which can simultaneously ensure complete ocular safety while enhancing athletic performance for over 250,000,000 players (Johnson & Garcia, 2022).

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Abstract: CRISPR/Cas systems are used for genome editing, both in basic science and in bio-technology. At the same time, CRISPR/Cas editors have several limitations, including insufficient specificity leading to "off-targets" and the dependence of activity on chromatin state. A number of highly specific Cas9 variants have been obtained now, but most of them are characterized by reduced activity on eukaryotic chromatin. We identified a spatial cluster of amino acid residues in the PAM-recognizing domain of Streptococcus pyogenes Cas9, whose mutations restore the activity of one of the highly specific forms of SpyCas9 without reducing its activity in Saccharomyces cere-visiae. In addition, one of these new mutations also increases the efficiency of SpyCas9-mediated editing of a site localized on the stable nucleosome. The improved Cas9 variants we obtained, which are capable of editing hard-to-reach regions of the yeast genome, may help in both basic research and yeast biotechnological applications.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

53% of adults in the US acknowledge racial bias as a significant issue, 23% of Asian adults experience cultural and ethnic bias, and more than 60% conceal their cultural heritage after racial abuse. AI models like ChatGPT and Google Bard, trained on historically biased data, inadvertently amplify racial and ethnic bias and stereotypes. This paper addresses the issue of racial bias in AI models using scientific, evidence-based analysis and auditing processes to identify biased responses from AI models and develop a mitigation tool. The methodology involves creating a comprehensive database of racially biased questions, terms, and phrases from thousands of legal cases, Wikipedia, and surveys, and then testing them on AI Models and analyzing the responses through sentiment analysis and human evaluation, and eventually creation of an 'AI-BiasAudit,' tool having a racial-ethnic database for social science researchers and AI developers to identify and prevent racial bias in AI models.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

In the paper, the authors find closed forms for derangement numbers in terms of the Hessenberg determinants, discover a recurrence relation of derangement numbers, present a formula for any higher order derivative of the exponential generating function of derangement numbers, and compute some related Hessenberg and tridiagonal determinants.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Interferons (IFNs) are cytokines involved in the immune response that act on innate and adaptive immunity. These proteins are natural cell-signaling glycoproteins expressed in response to viral infections, tumors, and biological inducers and constitute the first line of defense of vertebrates against infectious agents. They have been marketed for more than 30 years with considerable impact on the global therapeutic protein market thanks to their diversity in terms of biological activities. They have been used as single agents or with combination treatment regimens, demonstrating promising clinical results, resulting in 22 different formulations approved by regulatory agencies. The 163 clinical trials with currently active IFNs reinforce their importance as therapeutics for human health. However, their application has presented difficulties due to the molecules’ size, sensitivity to degradation, and rapid elimination from the bloodstream. For some years now, work has been underway to obtain new drug delivery systems to provide adequate therapeutic concentrations for these cytokines, decrease their toxicity and prolong their half-life in the circulation. Although different research groups have presented various formulations that encapsulate IFNs, to date, there is no formulation approved for use in humans. The current review exhibits an updated summary of all encapsulation forms presented in the scientific literature for these cytokines IFNα, IFNß, and IFNγ, from the year 1996 to the year 2021, considering parameters such as: encapsulating matrix, route of administration, and encapsulation.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Gene editing tools such as CRISPR-Cas9 have created unprecedented opportunities for genetic studies in plants and animals. We designed a course-based undergraduate research experience (CURE) to train introductory biology students in the concepts and implementation of gene editing technology as well as develop their soft skills in data management and scientific communication. We present two versions of the course that can be implemented with twice-weekly meetings over a five-week period. In the remote-learning version, students perform homology searches, design guide RNAs and primers, and learn the principles of molecular cloning. This version is appropriate when access to laboratory equipment or in-person instruction is limited, such as closures that have occurred in response to the Covid-19 pandemic. In the in-person version, students design guide RNAs, clone CRISPR-Cas9 constructs, and perform genetic transformation of the model plant Arabidopsis thaliana. The highly parallel nature of the CURE makes it possible to target dozens to hundreds of genes, depending on the number of course sections available. Applying this approach in a sensitized mutant background enables focused reverse genetic screens for genetic suppressors or enhancers. The course can be readily adapted to other organisms or projects that employ gene editing.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

The study aimed to investigate the impact of incorporating deep learning strategies in mathematics instruction on students' problem-solving abilities, critical thinking skills, academic achievement, and mathematical skills development. The study population consisted of 280 students, with a sample size of 162 participants. Employing a purely quantitative approach, data collection utilized questionnaires and achievement tests as instruments. Data analysis involved simple linear regression, descriptive analysis, and Pearson correlation. The results of the study revealed that there was no significant enhancement observed in students' problem-solving abilities and critical thinking skills when deep learning strategies were incorporated into mathematics instruction. Additionally, students' attitudes towards deep learning activities in mathematics showed no effect on their academic achievement. Furthermore, students' engagement levels in deep learning activities did not impact their development of mathematical skills. Lastly, the frequency of deep learning activities in the mathematics classroom did not show a significant relationship with students' academic performance. These findings suggest that the implementation of deep learning strategies in mathematics instruction did not yield notable improvements in the specified areas based on the study outcomes.

Human pluripotent stem cells (PSCs), which include both embryonic and induced pluripotent stem cells, are widely used in fundamental and applied biomedical research. They have been instrumental for better understanding development and cell differentiation processes, disease origin and progression, and can aid in the discovery of new drugs. PSCs also hold great potential in regenerative medicine to treat or diminish the effects of certain debilitating diseases, such as degenerative disorders. However, some concerns have recently been raised over their safety for the use in regenerative medicine. One of the major concerns is the fact that PSCs are prone to errors in passing the correct number of chromosomes to daughter cells, resulting in aneuploid cells. Aneuploidy, characterised by an imbalance in chromosome number, elicits the upregulation of different stress pathways that are deleterious to cell homeostasis, impair proper embryo development and can potentiate cancer development. In this review we will summarise known molecular mechanisms recently revealed to impair mitotic fidelity in human PSCs and the consequences of the decreased mitotic fidelity of these cells. We will finish with speculative views on how the physiological characteristics of PSCs can affect the mitotic machinery and how their suboptimal mitotic fidelity may be circumvented.

The metal chelator PBT2 (5,7-dichloro-2-[(dimethylamino)methyl]-8-hydroxyquinoline) acts as a terdentate ligand capable of forming binary and ternary Cu2+ complexes. It was clinically trialed as an Alzheimer’s disease (AD) therapeutic but failed to progress beyond phase II. The β-amyloid (Aβ) peptide associated with AD was recently concluded to form a unique Cu(Aβ) complex that is inaccessible to PBT2. Herein, it is shown that the species ascribed to this binary Cu(Aβ) complex in fact corresponds to ternary Cu(PBT2)NIm[Aβ] complexes formed by anchoring of Cu(PBT2) on imine nitrogen (NIm) donors of His side chains. The primary site of ternary complex formation is His6, having a conditional stepwise formation constant at pH 7.4 (K [M−1] ) of log K = 6.4 ± 0.1, and a second site is supplied by His13 or His14 (log K = 4.4 ± 0.1). The stability of Cu(PBT2)NIm[H13/14] is comparable with that of the simplest ternary complexes involving free imidazole (log K = 4.22 ± 0.09) and histamine (log K = 4.00 ± 0.05). The 100-fold larger formation constant for Cu(PBT2)NIm[H6] indicates that outer-sphere ligand–peptide interactions strongly stabilize its structure. Despite the relatively high stability of Cu(PBT2)NImH6, PBT2 is a promiscuous Cu2+-binding ligand capable of forming a ternary Cu(PBT2)NIm complex with any ligand containing NIm donor. These ligands include histamine, L-His, and ubiquitous His side chains of peptides and proteins in the extracellular milieu, whose combined effect should outweigh that of a single Cu(PBT2)NIm[H6] complex regardless of its stability. We therefore conclude that PBT2 is capable of accessing Cu(Aβ) complexes with high stability but not specificity. The results have implications for future AD therapeutic strategies and understanding the role of PBT2 in the bulk transport of transition metal ions. Given the repurposing of PBT2 as a drug for breaking antibiotic resistance, ternary Cu(PBT2)NIm and analogous Zn(PBT2)NIm complexes may be relevant to its antimicrobial properties.

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

Mutations in KRT1 (keratin 1) or KRT10 (keratin 10) underlie a spectrum of diseases known as keratinopathic ichthyoses. Epidermolytic ichthyosis (EI) is caused by heterozygous missense mutations in the genes KRT1 or KRT10, mutations in the gene KRT2 (keratin 2) lead to superficial epidermolytic ichthyosis, and congenital reticular ichthyosiform erythroderma is caused by frameshift mutations in the genes KRT10 or KRT1, which lead to the phenomenon of revertant mosaicism. Epidermolytic ichthyosis is also present in a mosaic pattern known as epidermolytic (acantholytic) nevus, isolated or diffuse. In the latter case, gonadic involvement is possible, leading to a rare pedigree in which a parent with diffuse epidermolytic nevus (linear EI) gives birth to a child affected by EI. We present here an update on the phenotypic presentations of keratinopathic ichthyoses and their molecular mechanisms.

Tremendous progress has been witnessed in artificial intelligence within the domain of neural network backed deep learning systems and its applications. As we approach the post Moore’s Law era, the limit of semiconductor fabrication technology along with a rapid increase in data generation rates have lead to an impending growing challenge of tackling newer and more modern machine learning problems. In parallel, quantum computing has exhibited rapid development in recent years. Due to the potential of a quantum speedup, quantum based learning applications have become an area of significant interest, in hopes that we can leverage quantum systems to solve classical problems. In this work, we propose a quantum deep learning architecture; we demonstrate our quantum neural network architecture on tasks ranging from binary and multi-class classification to generative modelling. Powered by a modified quantum differentiation function along with a hybrid quantum-classic design, our architecture encodes the data with a reduced number of qubits and generates a quantum circuit, loading it onto a quantum platform where the model learns the optimal states iteratively. We conduct intensive experiments on both the local computing environment and IBM-Q quantum platform. The evaluation results demonstrate that our architecture is able to outperform Tensorflow-Quantum by up to 12.51% and 11.71% for a comparable classic deep neural network on the task of classification trained with the same network settings. Furthermore, our GAN architecture runs the discriminator and the generator purely on quantum hardware and utilizes the swap test on qubits to calculate the values of loss functions. In comparing our quantum GAN, we note our architecture is able to achieve similar performance with 98.5% reduction on the parameter set when compared to classical GANs. With the same number of parameters, additionally, QuGAN outperforms other quantum based GANs in the literature for up to 125.0% in terms of similarity between generated distributions and original data sets.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

Using the example of III-V nitrides crystallizing in a wurtzite structure (GaN, AlN, InN), this review presents the special role of hydrostatic pressure in studying semiconductor properties. Starting with a brief description of high pressure techniques for growing bulk crystals of nitride compounds, we focus on the use of hydrostatic pressure techniques in both experimental and theoretical investigations of special properties of nitride compounds, their alloys and quantum structures. The band gap pressure coefficient is one of the most important parameters in semiconductor physics. Trends in its behavior in nitride structures, together with trends in pressure-induced phase transitions, are discussed in the context of the behavior of other typical semiconductors. Using InN as an example, the pressure-dependent effects typical of very narrow bandgap materials, such as conduction band filling or effective mass behavior, are described. Interesting aspects of bandgap bowing in In-containing nitride alloys, including pressure and clustering effects, are discussed.Hydrostatic pressure also plays an important role in the study of native defects and impurities, as illustrated by the example of nitride compounds and their quantum structures. Experiments and theoretical studies on this topic are reviewed. Special attention is given to hydrostatic pressure and strain effects in short periods nitride superlattices. The explanation of the discrepancies between theory and experiment in the optical emission and its pressure dependence from InN/GaN superlattices led to the well-documented conclusion that InN growth on the GaN substrate is not possible. The built-in electric field present in InGaN/GaN and AlGaN/GaN heterostructures crystallizing in wurtzite lattice can reach several MV/cm, leading to drastic changes in the physical properties of these structures and related devices. It is shown how hydrostatic pressure modifies these effects and helps to understand their origin.

The question of the relevance of human and natural capital, as well as the potential adverse effect of natural capital on economic growth, has gained increased attention in development economics. The aim of this paper is to theoretically and empirically assess the relevance of several forms of capital on economic growth in small economies that are dependent upon tourism or natural resources. The empirical framework is based on Impulse Response Functions obtained from Vector Autoregressive models in which we focus on the model where economic growth is the dependent variable for ten small economies that are dependent upon either tourism or natural resources. We find that there is evidence of the ‘’natural resource curse’’, especially in the economies that have a strong dependence on resources that are easily substitutable and whose prices constantly fluctuate. We further find that in the majority of observed cases the type of capital these small economies are most dependent on for their economic growth causes negative impulses in the majority of the observed periods. The main policy recommendation should be to assure that even these small economies should strive towards further diversification and avoid dependence on only one segment of their economy.

Despite significant advancements in Artificial Intelligence (AI) and Large Language Models (LLMs), detecting and mitigating bias remains a critical challenge, particularly within social media platforms like X (formerly Twitter) and in addressing cyberbullying present on them. This research investigates the effectiveness of leading LLMs in generating synthetic biased and cyberbullying data and evaluates the proficiency of Transformer AI models in detecting bias and cyberbullying within both authentic and synthetic contexts. The study involves semantic analysis and feature engineering on a dataset of over 48,000 sentences related to cyberbullying collected from Twitter (before it became X). Leveraging state-of-the-art LLMs such as ChatGPT-4o, Pi AI, Claude 3 Opus, and Gemini-1.5, synthetic biased, cyberbullying, and neutral data were generated to deepen the understanding of bias in human-generated data. AI models including DeBERTa, Longformer, BigBird, HateBERT, MobileBERT, DistilBERT, BERT, RoBERTa, ELECTRA, and XLNet were initially trained to classify Twitter cyberbullying data and subsequently fine-tuned, optimized, and quantized for multilabel classification (detecting both biases and cyberbullying). The study's outcomes include a prototype of a hybrid application that combines a Bias Data Detector and a Bias Data Generator, validated through extensive testing.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

Due to the high computational burden and the high nonlinearity of the responses, crashworthiness optimizations are notoriously hard-to-solve challenges. Among various approaches, methods like the Successive Response Surface Method (SRSM) have stood out for their efficiency in enhancing baseline designs within a few iterations. However, these methods have limitations that restrict their application. Their minimum iterative resampling required is often computationally prohibitive. Furthermore, surrogate models are conventionally constructed using Polynomial Response Surface (PRS), a method that is poorly versatile, prone to overfitting, and incapable of quantifying uncertainty. Furthermore, the lack of continuity between successive response surfaces results in suboptimal predictions. This paper introduces the Multi-Fidelity Successive Response Surface (MF-SRS), a Gaussian process-based method, which leverages a nonlinear multi-fidelity approach for more accurate and efficient predictions compared to SRSM. After initial testing on synthetic problems, this method is applied to a real-world crashworthiness task: optimizing a bumper crossmember and crash box system. Results, benchmarked against SRSM and the Gaussian Process Successive Response Surface (GP-SRS) – a single-fidelity Gaussian process-driven extension of SRSM, show that MF-SRS offers distinct advantages. Specifically, it improves upon the specific energy absorbed optimum value achieved by SRSM by 14.1 %, revealing its potential for future applications.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Keywords: Deep mining; Drill bit structural parameters; Fidelity coring; Abaqus simulation and analysis.

The growing population meet the challenge for agricultural production. CRISPR/Cas9 technology is based on plant research for the development of the new varieties as well as disease resistance crops. In addition the deletion of significant characters makes the new alleles from the CRISPR/Cas9. Recent and reliable molecular scissor for genetic engineering. The review is focused on the various application of the CRISPR/Cas9 technology in plant enhancement of plant disease resistance, stress burden in plant, nutritional improvement, and quality of crops from the CRISPR/Cas9 system. The clustered regularly interspaced short palindromic repeat (CRISPR)-associated protein9 (cas9) is adopted from the prokaryotic type II system. CRISPR/Cas9 is simplicity and efficiency than ZENs and TALENs for the genome engineering. Due to rapid growing of the CRISPR/Cas9 system has been formulate the adaptation of many plant species. The current advancement of plants and future schemes of improve of CRISPR technology has been presented in contest of multiplex editing, knowledge on induced mutation whether the factor effect in CRISPR/Cas9 technology in plant. Remarkable perspective and challenges of CRISPR/Cas9 technology in significance of plant genetic modification.

In this paper, we focus on the impact of financial liberalization on stability of emerging stock market. We identify crises in a group of Latin American (Argentina, Brazil and Chile) and Asian countries (Philippines, Korea, Taiwan and Thailand) during 1975–2005. This paper aims to apply the methodology of CMAX method. Our results indicate that liberalization triggers more unstable stock market in the short run and generate several crises. Still, liberalization seems to generate more stable financial markets in the long run. Financial liberalization does not increase the frequency of crises in emerging countries and at long-term, crises are less several.

Because only two variables are needed to characterize a simple thermodynamic system in equilibrium, any such system is constrained on a 2D manifold. Of particular interest are the exact 1-forms on the cotangent space of that manifold, since the integral of exact 1-forms is path-independent, a crucial property satisfied by state variables such as internal energy dE and entropy dS. Our prior work [1] shows that given an appropriate language of vector calculus, a machine can re-discover the Maxwell equations and the incompressible Navier-Stokes equations from data. In this paper, We enhance this language by including differential forms and show that machines can re-discover the equation for entropy dS given data. Since entropy appears in various fields of science in different guises, a potential extension of this work is to use the machinery developed in this paper to let machines discover the expressions for entropy from data in fields other than classical thermodynamics.

Grounded on urban morphology studies, the research tries to overcome the analysis of the permanents elements of the city seeking for a transitional paradigm in urban morphology, aiming at grasping the dynamics in urban evolution and providing operative tools for urban regeneration design in an adaptive approach. A combination of four actions of urban analysis is here suggested to highlight urban dynamics: a. Sorting the transitional steps of urban morphologies (within rapid market processes), b. Underlining rules and Processes characterizing urban coding in transition, c. Mapping urban assemblages in the adaptive city and d. Reading and representing urban permutation phenomenon. The results of this multifaced and multidimensional set of analytical tools allow to outline a new design thinking paradigm moving towards a parametric approach to urban design of cities in transition broadening the extent of urban regeneration process and supporting urban policies in the framework community based approach.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Novel Cellular Immunotherapy with engineered T cells has improved cancer treatment and established therapeutic promises to prevent tumor formation in clinical studies. Due to certain restrictions and difficulties, CAR and TCR T cells therapies were inadequate at points. CRISPR Cas9 genome-editing tool has a significant potential for these two cell-based therapies. As a specialized gene-editing technique, CRISPR Cas9 is used to repair genetic alternation with minimum damage. It is used as an adjunct to Immunotherapy to stimulate a more robust immune response. CRISPR has long outpaced other target-specific genome editing methods such as ZFNs and TALEN due to its high efficiency, competence in targeting, and stable operating condition. CRISPR can overcome the two major drawbacks of universal CAR T cells: allorejection and graft-vs-host disease. TCR-based T cell treatment can reduce inappropriate binding between endogenous and transgenic TCR, resulting in a reduction of severe toxicity. The CAR and TCR T based cell therapies uphold an excellent future for tumor malignancies This article has elucidated the administration of CRISPR Cas9 in Novel Cellular Immunotherapy, CAR, and TCR T cell therapy. However, this article did not fail to observe this technology's ethical concerns, limitations, and challenges. Furthermore, the article compares CRISPR-mediated allogeneic CAR T cell to TCR-T cell therapy.

Research on Cas9 nucleases from different organisms holds great promise for advancing genome engineering and gene therapy tools as it could provide novel structural insights into CRISPR editing mechanisms, expanding its application area in biology and medicine. The current study focuses on generating a construct to express a compact Cas9 nuclease (AnoCas9) from the thermophilic microorganism Anoxybacillus flavithermus. Next, distinctive AnoCas9 properties are investigated. AnoCas9 gene is expressed in E.coli producing a polypeptide fused with the maltose-binding protein (MBP-AnoCas9). His-Tag in its structure enables purification using metal-chelate chromatography followed by the cleavage of the polypeptide by TEV protease. Bioinformatical analysis of the CRISPR array found in the genome of an Anoxybacillus flavithermus strain helps predict a functional PAM sequence for AnoCas9, which is supported by in vitro experiments. The purified protein demonstrates nuclease activity in the presence of crRNA:tracrRNA duplex in the 37-60 °С range, with maximum activity observed at 45-55 °С. The analysis of FAM-labeled dsDNA substrate cleavage has allowed us to determine the functional AnoCas9 PAM motif as 5’-NNNNCDAA-3’. Thus, AnoCas9 adds to the repertoire of thermophilic Cas9 effectors and its properties suggest application in areas requiring the presence of thermostable CRISPR/Cas systems.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

Lipids have not traditionally been considered likely candidates for catalyzing reactions in biological systems. However, there is significant evidence that aggregates of amphiphilic compounds are capable of catalyzing reactions in synthetic organic chemistry. Here we demonstrate the potential for the hydrophobic region of a lipid bilayer to provide an environment suitable for catalysis by means of a lipozyme, or lipid aggregate capable of speeding up a chemical reaction. By bringing organic molecules into the non-polar or hydrophobic region of a lipid bilayer, reactions can be catalyzed by collections of small, nonpolar or amphiphilic molecules. We demonstrate this concept by the ester hydrolysis of calcein-AM to produce a fluorescent product, which is a widely used assay for esterase activity in cells. The reaction was first carried out in a two phase octanol-water system with the organic phase containing the cationic amphiphiles cetyltrimethylammonium bromide (CTAB) or octadecylamine. The octanol was then replaced with DOPC added to the water in the form of vesicles, where the reaction was also found to be carried out. The reaction was monitored using quantitative fluorescence which revealed catalytic turnover numbers on a scale of 10−4s−1 for each system, which is comparable to some slow enzymes. The reaction product was characterized by 1H-NMR measurements which were consistent with ester hydrolysis. The implications of thinking about lipid aggregates as catalytic entities are discussed in the context of biochemistry, pharmacology and synthetic biology.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

High-power lasers play an important role in modern science, industry, and medicine. A signifi-cant milestone was reached on December 5, 2022, when Inertial Confinement Nuclear Fusion (ICF) achieved scientific breakeven, releasing more energy than the input laser energy. Additionally, Extreme Ultraviolet Lithography (EUVL) has enabled the development of microchips with 3 nm process nodes, marking a leap in semiconductor technology. These examples together with the recent achievement of a 10 PW (1015 W) laser output heralds remarkable advancements in technology and science soon. Laser systems are broadly classified based on their operating re-gimes into two main categories: Continuous Wave (CW) operation, where the laser is continuously pumped and emits a steady beam of light, and the pulsed regime, in which the laser pro-duces single or multiple pulses at various repetition rates. This review will primarily focus on pulsed laser systems, exploring their various types and recent technological advancements.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

In most Eukaryotes, ubiquitin either exists as free monoubiquitin or as a molecule that is covalently linked to other proteins. These two forms cycle between each other and due to the concerted antagonistic activity of ubiquitylating and deubiquitylating enzymes, an intracellular ubiquitin equilibrium is maintained that is essential for normal biological function. However, measuring the level and ratio of these forms of ubiquitin has been difficult and time consuming. In this paper, we have adapted a simple immunoblotting technique to monitor ubiquitin content and equilibrium dynamics in different developmental stages and tissues of Drosophila. Our data show that the level of total ubiquitin is distinct in different developmental stages, lowest at the larval-pupal transition and in three days old adult males, and highest in first instar larvae. Interestingly, the ratio of free mono-ubiquitin remains within 30-50% range of the total throughout larval development, but peaks to 70-80% at the larval-pupal and the pupal-adult transitions. It stays within the 70-80% range in adults. In developmentally and physiologically active tissues, the ratio of free ubiquitin is similarly high, most likely reflecting a high demand for ubiquitin availability. We also used this method to demonstrate the disruption of the finely tuned ubiquitin equilibrium by the abolition of proteasome function or the housekeeping deubiquitylase, Usp5. Our data support the notion that the ubiquitin equilibrium is regulated by tissue- and developmental stage-specific mechanisms.

Bayesian techniques for engineering problems, that rely on Gaussian process (GP) regression, are known for their ability to quantify epistemic and aleatory uncertainties and for being data efficient. The mathematical elegance of applying these methods usually comes at a high computational cost when compared to deterministic and empirical Bayesian methods. Furthermore, using these methods becomes practically infeasible in scenarios characterized by a large number of inputs and thousands of training data. The focus of this work is on enhancing Gaussian Process-based metamodeling and model calibration tasks, when the size of the training datasets is significantly large. To achieve this goal, we employ a stochastic variational inference algorithm that enables rapid statistical learning of the calibration parameters and hyperparameter tuning, while retaining the rigor of Bayesian inference. The numerical performance of the algorithm is demonstrated on multiple metamodeling and model calibration problems with thousands of training data.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

CRISPR/Cas9 has emerged as the predominant method for genome editing due to its cost-effectiveness and broad applicability, playing a crucial role in advancing sustainable practices across various sectors. This systematic review leverages the PRISMA methodology to explore CRISPR/Cas9's impact on environmental protection, thereby supporting the Sustainable Development Goals (SDGs). Analyzing data from the Web of Science, the review found significant growth in related publications, with a 30% increase since 2014, predominantly from the US, China, Germany, and the UK. The study categorizes the scientific developments into three trends: advancements in agriculture, gene editing techniques, and biofuel production. Key discussions include the use of CRISPR/Cas9 in developing fourth-generation biofuels and environmental biosensors, as well as its applications in enhancing genetic resilience and controlling invasive species. These innovations highlight CRISPR/Cas9's potential in promoting sustainable resource management and energy generation, marking a pivotal contribution to ecological conservation and sustainability efforts.

Tyrosyl-DNA phosphodiesterase 1 (TDP1) is a human DNA repair protein. It is a member of the phospholipase D family based on the structure similarity. TDP1 is a key enzyme involved in repairing stalled topoisomerase 1 (TOP1)-DNA complexes. Previously we obtained with the CRISPR/Cas9 method HEK293A cells with the homozygous knockout of the Tdp1 gene and used knockout cells as a cellular model for studying the mechanisms of anticancer therapy. In this work we studied for the first time by transcriptomic analysis the effect of Tdp1 gene knockout on genes expression changes in human HEK293A cell line. We received original data that may indicate a role of TDP1 in other process besides repair of DNA-TOP1 complex. The differentially expressed genes (DEGs) analysis revealed that TDP1 could be involved in different processes such as cell adhesion and communication, spermatogenesis, mitochondrial function, neurodegeneration, cytokine response, and MAPK pathway signaling.

Duchenne muscular dystrophy (DMD) is a fatal X-linked recessive neuromuscular disease prevalent in 1 in 3500 to 5000 males worldwide. As a result of mutations that interrupt the reading frame of the dystrophin gene (DMD), DMD is characterized by a loss of dystrophin protein which leads to decreased muscle membrane integrity, which increases susceptibility to degeneration. CRISPR/Cas9 technology has garnered interest as an avenue for DMD therapy due to its potential for permanent exon skipping, which can restore the disrupted DMD reading frame in DMD and lead to dystrophin restoration. An RNA-guided DNA endonuclease system, CRISPR/Cas9 allows for the targeted editing of specific sequences in the genome. The efficacy and safety of CRISPR/Cas9 as a therapy for DMD has been evaluated by numerous studies in vitro and in vivo, with varying rates of success. Despite the potential of CRISPR/Cas9-mediated gene editing for the long-term treatment of DMD, its translation into the clinic is currently challenged by issues such as off-targeting, immune response activation, and sub-optimal in vivo delivery. Its nature as being mostly a personalized form of therapy also limits applicability to DMD patients, who exhibit a wide spectrum of mutations. This review summarizes the various CRISPR/Cas9 strategies that have been tested in vitro and in vivo for the treatment of DMD. Perspectives on the approach will be provided, and the challenges faced by CRISPR/Cas9 in its road to the clinic will be briefly discussed.

Antisocial behavior is a behavior disorder inherited according to the inheritance of X-linked chromosome. This disorder derives from mutations in the MAOA gene. One of the mutations results in the MAOA-L allele activity. The MAOA-L allele activity can cause antisocial behavior in both healthy and unhealthy people. Antisocial behavior from healthy males can originate from maltreatment during childhood. Currently, MAOA inhibitor can reverse antisocial behavior to normal behavior in animal models. However, this disorder cannot be treated permanently; to treat it permanently in the future, technologies such as CRISPR/Cas9, iPSCs and ssODN are required. These technologies have succeeded to correct erroneous segments in the F8 gene and F9 gene. Both genes occupy the X chromosome. The MAOA gene also occupies the X chromosome. Therefore, it is reasonable to state that CRISPR/Cas9 and iPSCs technique for instance can be beneficial tools to edit the MAOA gene to treat antisocial behavior. CRISPR/Cas9 can be used in combination with iPSCs or ssODN for instance. This combination can greatly help the permanent healing of antisocial behavioral disorders.

BACKGROUND: Chronic hepatitis B infected with Hepatitis B virus remains a major health concern worldwide. Despite standard interferon-α and nucleotide analogues have been shown to reduce the deterioration of liver disease among chronic hepatitis B patients, covalently closed circular DNA was still difficult to eradicate. METHODS: A literature search of Pubmed and Web of science was performed with the following key words: ‘CRISPR’, ‘CRISPR/Cas9’, ‘hepatitis B’, ‘HBV’, ‘chronic hepatitis B’ and ‘HBV cccDNA’. The information about CRISPR/Cas9 for the treatment of HBV cccDNA or hepatitis B was reviewed. RESULTS: CRISPR/Cas9 could treat hepatitis B through suppressing or clearing HBV cccDNA with different gRNAs. CONCLUSION: With the emergence of CRISPR/Cas9 (the RNA-guided clustered regulatory interspaced short palindromic repeats, CRISPR) editing technology, clearance of hepatitis B virus and better prevention of liver carcinoma seemed to be possible.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Wheeled mobile robot dynamics and suitable controller design are challenging but rewarding fields of study. By understanding the dynamics of wheeled mobile robots, it could be possible to design suitable hybrid control schemes for wheeled mobile robots. Since hybrid control schemes involve combining individual control methods to create a more effective overall control strategy. This can be done in a variety of ways, such as using fuzzy linear quadratic Gaussian control. We were therefore inspired to create dynamic models and their controller designs for the wheeled mobile robot by examining the dynamics of the wheeled mobile robot. The novelty of the current paper is to hybridize the different control schemes for wheeled mobile robots in order to get better performance. Entire systems models were simulated in a MATLAB/SIMULINK environment. The results obtained for the settling time response by FLQG were 87.1% over LQG; this study compared the effectiveness of current and previous FLQG controllers in external disturbances and found peak amplitude improvements of 71.25%. Therefore, the proposed controller is suitable for use with the wheeled mobile robot.

Background: Fibonacci patterns and tubular forms both arose early in the phylogeny of multicellular organisms. Tubular forms offer the advantage of a regulated internal milieu, and Fibonacci forms may offer packing efficiencies. The underlying mechanisms behind the cellular genesis of Fibonacci and tubular forms remain unknown.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

This paper is a brief review of our work on the Planck quantized version of general rela- tivity theory. It demonstrates several straightforward methods to rewrite the same equations that we have already presented in other papers. We also explore a relatively new general relativity-inspired field equation based on the original Newtonian mass, which is very differ- ent from today’s kilogram mass. Additionally, we examine two other field equations based on collision space-time, where both energy and matter can be described simply as space and time. We are thereby fulfilling Einstein’s dream of a theory where energy and mass are not needed, or are just aspects of space and time. If this is extended beyond the 4-dimensional space-time formalism of general relativity theory to a 6-dimensional framework—with 3 space dimensions and 3 time dimensions—this ultimately reveals that they are two sides of the same coin. In reality, it is a three-dimensional space-time theory, where space and time are just two sides of the same coin.

Students have historically fared poorly on the West African Examinations Council’s (WAEC) mathematics exam. This study investigated senior high school students’ difficulties with studying Geometry in the Cape Coast Metropolis, Central Region, Ghana. Using the descriptive survey design, data were collected from 300 Senior High School Two (SHS 2) students using simple random sampling. Students responded to the questionnaire and a 30-item multiple-choice achievement test on geometry. Four geometry concepts students perceived difficult to study are Circle theorems, Perpendicularity of Tangent and radius of a circle, Angle between Tangent and a chord and Tangents from an external point. The reasons for the difficulty in studying geometry topics are the unavailability of instructional materials, the geometry topics being complex, and teachers not teaching geometry concepts to the students’ understanding. Students’ gender did not influence the learning of concepts in geometry at a 0.05 level of significance. There was an insignificantly weak positive correlation between the students’ performance and their perceived difficult geometry concepts. It was concluded that the Ministry of Education does not provide relevant instructional materials to the various schools to teach geometry concepts. Schools do not organise workshops and seminars for teachers on effectively teaching geometry concepts in mathematics.

For quantitative determination of honokiol (HNK) and metformin hydrochloride (M-HCl) by HPLC from formulations and from dissolution studies, a QbD approach using three factors - three levels design was implemented to optimize the chromatographic conditions. To study the impact of each variable on the peak area of both compounds and retention time of last compound eluted, the 3D response surface plots were developed. HNK and M-HCl were separated on a Thermoscientific ODS Hypersyl TM (250 x 4.6 mm, 5 μm) column mantained at 30 C, using 0.02 M acetate buffer (pH = 3) / methanol (15 / 85, v / v) as mobile phase with a flow rate of 1 mL/min. The injected volume was 20 L, and the detection wavelengths were 256 nm for HNK and 236 nm for M-HCl. The validation of proposed method showed a linearity range of 4 – 1200 μg/mL for M-HCl (r2 = 0.9992) and 1 – 300 μg/mL for HNK (r2 = 0.9998), good precision (RSD &lt; 2% for both HNK and M-HCl, in intra- and inter-day studies) and accuracy (mean recovery = 100.09% in the range 99.80 – 100.43% for M-HCl and mean recovery = 100.12% in the range 99.70 – 100.38% for HNK). The environmentally friendly nature of the method was confirmed by the evaluation of the method’s greenness. The proposed method was applied for the determination of HNK and M-HCl from oral dosage forms and in dissolution studies.

Clustered regularly interspaced short palindromic repeats or CRISPR, one of the major technological tools from nature's toolbox, has revolutionized the scientific world with its potential use in humans and plants. CRISPR Cas9 was first known as an adaptive immune system of bacteria. It is a system that cleaves foreign DNA. It has been exploited to be used as a genome editing tool for correcting genetic diseases in humans, for plants to create stress-resistant plants, and for a variety of different purposes. This review provides a basic overview of its applications in different areas of biological research. It has immense potential for a variety of researches, but it's still a mystery for science. It feels like scientists just know a tip of an iceberg.

In the last decade, the genetic engineering world has been shaken up by a relatively new genetic editing tool based on RNA-guided Nucleases (RGNs): the CRISPR/Cas9 system. Since the first report in 1987 and its characterization in 2007 as a bacterial defense mechanism, the interest and research on this system have grown exponentially. CRISPR systems provide immunity to bacteria against invading genetic material; however, with specific modifications in sequence and structure, it becomes a precise editing system that makes it possible to genetically modify almost any organism. There are diverse approaches regarding the refinement of these modifications, such as constructing more accurate nucleases, understanding the cellular context and facing the epigenetic conditions, or re-designing guide RNAs (gRNAs). Considering the critical importance for the correct CRISPR/Cas9 systems performance, our scope will emphasize in the latter approach. Hence, we present an overview of the past and the most recent guide RNA web-based design tools, highlighting their computational architecture and gRNA characteristics evolution through the years. Our study concisely explains the computational approaches that use machine learning techniques, deep neural networks, and large datasets of gRNA/target interactions to make possible both predictions and classifications directed to design, optimize, and create promising gRNAs suitable for future gene therapies.

The RNA-guided endonuclease system CRISPR-Cas9 has been extensively modified since its discovery, allowing its capabilities to be extending far beyond double-stranded cleavage to high fidelity insertions, deletions, and single base edits. Such innovations have been possible due to the modular architecture of CRISPR-Cas9 and the robustness of its component parts to modifications and the fusion of new functional elements. Here, we review the broad toolkit of CRISPR-Cas9-based systems now available for diverse genome editing tasks. We provide an overview of their core molecular structure and mechanism and distil the design principles used to engineer their diverse functionalities. We end by looking beyond the biochemistry and towards the societal and ethical challenges that these CRISPR-Cas9 systems face if their transformative capabilities are to be deployed in a safe and acceptable manner.

This paper introduces an innovative Particle Swarm Optimization (PSO) Algorithm in-corporating Sobol and Halton Random number samplings. It evaluates the enhanced PSO's performance against conventional PSO employing Monte Carlo Random Number Samplings. The comparison involves assessing the algorithms across nine benchmark problems and the renowned Travelling Salesman Problem (TSP). The re-sults reveal consistent enhancements achieved by the enhanced PSO utilizing Sob-ol/Halton samplings across the benchmark problems. Particularly noteworthy are the substantial improvements demonstrated by the enhanced PSO in solving the Travel-ling Salesman Problem. These findings underscore the efficacy of employing Sobol and Halton random number generation methods in enhancing algorithm efficiency.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

After the ban on tributyltin-based antifouling paints, DCOIT (4,5-Dichloro-2-octylisothiazol-3(2H)-one) became one of the most used antifouling biocides. DCOIT is a pseudo-persistent contaminant in port areas and is toxic to non-target species, but its ability to bioaccumulate and be transferred along the trophic chain remains unknown. This study aimed to preliminarily investigate the bioaccumulation, trophic transfer, and biomagnification of DCOIT and SiNC-DCOIT (DCOIT immobilized in silica mesoporous nanocapsules) from the microalga Tetraselmis chuii to the mussel Mytilus galloprovincialis during exposure experiments considering 24 h of uptake followed by 72 h depuration. Mussels rapidly internalized and metabolized both DCOIT and SiNC-DCOIT. The predator-prey biomagnification factors (BMFTL) suggested that both forms of the biocide can be trophically transferred, with higher concentrations of DCOIT and SiNC-DCOIT in mussels than in microalgae (BMFTL &gt; 1). However, the bioaccumulation and bioconcentration factors indicated a low bioaccumulation capability in the short term, suggesting that the depuration rate overcomes the uptake. Our findings contribute to the development of environmental risk assessments for DCOIT and SiNC-DCOIT, but do not exclude the possibility of DCOIT bioaccumulation in the long-term in areas with constant input of DCOIT. Further studies are needed to understand these processes under continuous exposure scenarios to DCOIT.

Rhododendron is well-known for the colorful corolla. Molecular marker systems have the potentials to elucidate genetic diversity as well as to assess the genetic fidelity in rhododendrons. In the present study, the reverse transcription domains of long terminal repeat retrotransposons were cloned from rhododendrons and used to develop inter-retrotransposon amplified polymorphism (IRAP) marker system. Subsequently, 198 polymorphic loci were generated from the IRAP and inter-simple sequence repeat (ISSR) markers, of which 119 were derived from the IRAP markers. It was justified that in rhododendrons, IRAP markers were superior to the ISSRs in some polymorphic parameters such as the average number of polymorphic loci (14.88 versus 13.17). In comparison with the single one, the combination of IRAPs and ISSRs systems was more discriminative for detecting 46 rhododendron accessions. Further, IRAP markers demonstrated more efficiency in genetic fidelity detection of in vitro R. bailiens, an endangered species just recorded in Guizhzhou Province, China. The available evidences revealed the distinct properties of IRAP and ISSR markers in the rhododendron-associated applications, and highlighted the availability of highly informative ISSR and IRAP markers in the genetic diversity evaluation and the genetic fidelity assessment of rhododendrons, which may facilitate the preservation and genetic breeding in rhododendron plants.

Aim: This study aimed to evaluate the effectiveness of a plyometric training program designed to enhance agility, speed, and social interaction among boys with mild intellectual disability (ID) aged 10-12, within the Special Olympics framework. Participants: Thirty-two boys (mean age = 10.69 ± 0.8 years; mean IQ = 61 ± 7) from three inclusive education centers participated in the study. Methods: The intervention consisted of a 10-week plyometric training program, conducted twice a week. Pre- and post-intervention assessments included the Reaction Time Test, 4-Corner Agility Test, 10-Meter Speed Run, 4x5 Meter Relay Test, and the Friendship Activity Scale (FAS). Results: The study found significant improvements across all measures. Reaction time decreased by 0.83 seconds (t = 7.44, p < 0.001), 4-corner agility improved by 0.77 seconds (t = 11.93, p < 0.001), 4x5 meter speed improved by 0.61 m/s (t = 17.37, p < 0.001), and 10-meter run speed improved by 1.55 m/s (t = -12.76, p < 0.001). Additionally, the FAS score increased by 0.81 points (t = 9.59, p < 0.001), indicating enhanced social interactions. Conclusion: The plyometric training program significantly improved agility, speed, and social interaction in children with mild ID, demonstrating the effectiveness of inclusive, adaptive physical education strategies within the Special Olympics framework.

Background: Antiphospholipid antibodies (aPL) are a laboratory criterion for the classification of antiphospholipid syndrome (APS), and are known to cause clinical symptoms: vascular thrombosis or obstetric complications. It is suggested that aPL may be associated with thromboembolism in severe COVID-19 cases. Aim: to combine clinical data with aPL findings at 4 time points (admission, worsening, discharge, 3-month follow-up) in patients hospitalized with COVID-19 pneumonia. Methods: current and past history of thrombosis and obstetric complications; aPL determined at 4 time points: anticardiolipin (aCL), anti-β2-glycoprotein I (anti- β2GPI) and antiphosphatidylserine/prothrombin (aPS/PT) of the IgM, IgG or IgA isotypes. Results: 111 patients with COVID-19 pneumonia were enrolled. During hospitalization, 7 patients died, 3 of them due to pulmonary artery thromboembolism (none was aPL positive). Only one of the five who developed pulmonary artery thrombosis was aPL positive. Of 9/101 patients with a history of thrombosis, 5 had arterial thrombosis and none was aPL positive at admission and follow-up; 4 had venous thrombosis and one was aPL positive at all time points (newly diagnosed APS). Of these 9/101 patients, 55.6% were transiently aPL positive at discharge only, compared to 26.1% without history of thrombosis (p=0.05). Conclusions: aPL were not associated with fatal outcomes and vascular thrombosis; aPL were transiently positive in more than half of patients with a history of thrombosis.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

Up to now, Schrödinger equation, Klein-Gordon equation (KGE) and Dirac equation are believed the fundamental equations of quantum mechanics. Schrödinger equation has a defect that there is no NKE solutions. Dirac equation has positive kinetic energy (PKE) and negative kinetic energy (NKE) branches. Both branches should have low momentum, or nonrelativistic, approximations: one is Schrödinger equation and the other is NKE Schrödinger equation. KGE has two problems: it is an equation of second time derivative, and calculated density is not definitely positive. To overcome the problems, it should be revised as PKE and NKE decoupled KGEs. The fundamental equations of quantum mechanics after the modification have at least two merits. They are of unitary in that everyone contains the first time derivative and are symmetric with respect to PKE and NKE. This reflects the symmetry of the PKE and NKE matters, as well as matter and dark matter, of our universe. The problems of one-dimensional step potentials are resolved by means of the modified fundamental equations for a nonrelativistic particle.

The CRISPR/Cas9 gene editing system has enormous potential in the treatment of multiple genetic disorders. To fully harness this potential, it is essential to deliver CRISPR-Cas9 components safely and effectively into the nuclei of target cells. In this study, we tested the amphipathic cell-penetrating peptide LAH5, previously used for DNA delivery, to intracellularly deliver spCas9: sgRNA ribonucleoprotein (RNP) and RNP/single-stranded homology-directed repair (HDR) template. We discovered that the LAH5 peptide effectively formed nanocomplexes with both RNP and RNP/HDR cargo, and that these nanocomplexes were taken up by cells effectively. Peptide/RNP nanocomplexes were characterized for size and charge, and nanocomplexation with RNP and RNP/HDR cargo was demonstrated via an electrophoretic mobility shift assay. Various ratios of peptide/RNP nanocomplexes were functionally screened on fluorescent reporter cell lines for gene editing and HDR-mediated gene correction. Additionally, targeted gene editing of the CCR5 gene was demonstrated in various cell lines. This LAH5-based delivery strategy paves the way for the development of therapeutic delivery systems for CRISPR/Cas-based genomic engineering.

Despite the high quality of soybean protein, raw soybeans and soybean meal cannot be directly included into animal feed mixtures due to the presence of Kunitz (KTi) and Bowman Birk protease inhibitors (BBi) which reduces animal performance. Heat treatment can substantially inactivate trypsin and chymotrypsin inhibitors (BBi) but such treatment is energy intensive, adds expense, and negatively impact the quality of seed proteins. As an alternative approach we have employed CRISPR/Cas9 gene editing to create mutations in BBi genes to drastically lower the protease inhibitor content in soybean seed. Agrobacterium-mediated transformation was used to generate several stable transgenic soybean events. These independent CRISPR/Cas9 events were examined in comparison to wild type plants using Sanger sequencing, proteomic analysis, trypsin/chymotrypsin inhibitor activity assays and q15RT-PCR. Collectively, our results demonstrate the creation of an allelic series of loss of function mutations affecting the major BBi gene in soybean. Mutations in two of the highly expressed seed specific BBi genes lead to substantial reductions in both trypsin and chymotrypsin inhibitor activities.

Clustered regularly interspaced short palindromic repeats/associated protein 9 nuclease (CRISPR/Cas9) technology guided by a single-guide RNA (sgRNA) has recently opened a new avenue for antiviral therapy. A unique capability of the CRISPR/Cas9 system is multiple genome engineering. However, there are few applications in insect viruses by a single Cas9 enzyme targeting two or more sgRNA at different genomic sites for simultaneous production of multiple DNA breaks. To address the need for multi-gene editing and sustained delivery of multiplex CRISPR/Cas9-based genome engineering tools, we developed a one-vector (pSL1180-Cas9-U6-sgRNA) system to express multiple sgRNA and Cas9 protein to excise Bombyx mori nucleopolyhedrovirus (BmNPV) in insect cells. Here, ie-1, gp64, lef-11, and dnapol genes were screened and identified as multiple sgRNA editing sites according to the BmNPV system infection and DNA replication mechanism. Furthermore, we constructed a multiplex editing vector sgMultiple to efficiently regulate multiplex gene editing steps and inhibit BmNPV replication after viral infection. This is the first report that describes the application of multiplex CRISPR/Cas9 system inhibiting insect virus replication. This multiplex system can significant enable the potential of CRISPR/Cas9-based multiplex genome engineering in transgenic silkworms.

Knee osteoarthritis (KO) is an important health condition, affecting one third of the people aged 65 years or more. Pain is the main cause of disability. Pain management in KO includes pharmacological and non-pharmacological modalities. Patient education, lifestyle changes, physical exercise and physical agents are prescribed as a first approach for pain control. Laser therapy is part of many therapeutical protocols, with two forms, low-level laser therapy (LLLT) and high-intensity laser therapy (HILT). The paper aimed at stressing the advantages of HILT, based on a greater wavelength, higher energy delivery and deeper tissue penetration. Research on 23 published trials revealed that analgesic effect is rapid, cumulative and long lasting. Compared to sham, to LLLT or to other associations of therapeutical modalities, HILT provided significantly better results on pain reduction and functional improvement. Ultrasound examination showed reduction of intraarticular inflammation.

A high-gain broadband circularly polarized crossed dipole antenna is designed. This antenna utilizes two pairs of cross dipoles and a pair of phase delay lines to form circularly polarized radiation. Open-circuit stubs are loaded on the four arms of these two pairs of cross dipoles to introduce new circularly polarized resonating frequency. A rectangular ring patch is introduced directly below the cross dipoles to form the third circularly polarized resonating frequency, thereby broadening the axial ratio bandwidth of the antenna. In addition, metal posts are loaded at the four right angles of the rectangular ring patch to increase the antenna gain. Measurement results show that the antenna achieves a 3dB axial ratio bandwidth of 29.2% (1.9 GHz-2.55 GHz) and maintains a gain of 7.5 dB within the passband, exhibiting good circularly polarized radiation performance.

YOLOv8, as an efficient object detection method, can swiftly and precisely identify objects within images. However, traditional algorithms encounter difficulties when detecting small targets in remote sensing images, such as missing information, background noise, and interactions among multiple objects in complex scenes, which may affect performance. To tackle these challenges, we propose an enhanced algorithm optimized for detecting small objects in remote sensing images, named HP-YOLOv8. Firstly, we design the C2f-D-Mixer (C2f-DM) module as a replacement for the original C2f module. This module integrates both local and global information, significantly improving the ability to detect features of small objects. Secondly, we introduce a feature fusion technique based on attention mechanisms, named Bi-Level Routing Attention in Gated Feature Pyramid Network (BGFPN). This technique utilizes an efficient feature aggregation network and reparameterization technology to optimize information interaction between different scale feature maps, and through the Bi-level Routing Attention (BRA) mechanism, it effectively captures critical feature information of small target objects. Finally, we propose the Smooth Mean Perpendicular Distance Intersection over Union (SMPDIoU) loss function. The method comprehensively considers the shape and size of detection boxes, enhances the model's focus on the attributes of detection boxes and provides a more accurate bounding box regression loss calculation method. To demonstrate our approach's efficacy, we conduct comprehensive experiments across the RSOD, NWPU VHR-10, and VisDrone2019 datasets. The experimental results show that the HP-YOLOv8 achieves 95.11%, 93.05%, and 53.49% in the [email protected] metric, and 72.03%, 65.37%, and 38.91% in the more stringent [email protected]:0.95 metric, respectively.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

UPF3B is a constituent of the classical nonsense-mediated mRNA decay (NMD) pathway that degrades both the aberrant transcripts and a set of physiological transcripts. In higher eukaryotes, UPF3B have significant biochemical functions in diverse cellular processes including NMD and translation. UPF3B plays a crucial role in neuronal development and differentiation. Next-generation sequencing technologies identified several loss-of-function mutations in the UPF3B gene that results in neuro-developmental disorders in humans. To uncover the mechanistic role of UPF3B in neuronal functions, we have generated the UPF3B-knockout mammalian cell line model system using CRISPR-Cas9 gene editing method. RNA-Sequencing Analysis of cellular transcriptome from UPF3B-KO cells identified specific genes involved in cell growth and neuronal functions. Altered expression of genes related to the axon guidance pathway delineated the UPF3B function to regulate the neuron-specific genes. Functional enrichment analysis identified the genes involved in the disorders related to mental health and intellectual disability. Our study has the potential to identify the direct players of intellectual disability and will have broader implications.

This paper aims to investigate the coal thickness change area of the combined rock strata energy accumulation law. The method of connecting a uniaxial compression experiment with a theoret-ical analysis is used in this work. We employ a combination of coal and rock to carry out our studies. We investigate how different lithologies and ratios of coal-rock height affect the me-chanical properties of the mixture and the law governing energy accumulation. We have deter-mined the following facts: (1) The combination's peak strength and elastic modulus exceed that of coal and are inferior to that of rock but are nearer to that of coal. (2) When the coal-rock height ratios are dissimilar, the peak strength and modulus of elasticity of the combination show a negative correlation with the coal-thickness share, and the pre-peak energy accumulation and impact energy index of the combination shows a positive correlation with the coal-thickness share. (3) For the combination with the same coal-rock height ratio, the peak strength, elastic modulus, pre-peak energy accumulation, and impact energy index all increase with greater rock strength and elastic modulus. The presence of a hard rock layer affects the accumulation of pre-peak energy. ( 4 ) The stress in the surrounding rock gradually decreases as the coal thick-ness increases. In the area where coal thickness declines, the stress in surrounding rock is higher than that in the region where it thickens. The energy stored in the surrounding rock is directly proportional to the coal in the zone. Conversely, areas with thinner coal deposits exhibit a lower energy storage capacity in the surrounding rock than those with thicker coal deposits. The stress distribution of surrounding rock in coal thickness change is abnormal; substantial energy accu-mulation can swiftly initiate dynamic disasters, such as rock bursts. This study has important reference significance for preventing and controlling rock burst in coal thickness change areas.

We compute explicitly traces of one-dimensional diffusion processes. The obtained trace forms can be regarded as Dirichlet forms on graphs. Then we discuss conditions ensuring the trace forms to be conservative. Finally, the obtained results are applied to the one-dimensional diffusion related to the Bessel’s process of order $\nu$.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

Fanconi anemia (FA) develops due to a mutation in one of the FANC genes that are involved in repair of interstrand crosslinks (ICLs). FANCG, a member of the FA core complex, is essential for ICL repair. Previous FANCG-deficient mouse models were generated with drug-based selection cassettes in mixed mice backgrounds, leading to a disparity in interpretation of genotype-related phenotype. To exclude these confounders, we created a Fancg-KO (KO) mouse model using CRISPR/Cas9. The entire Fancg locus was targeted and maintained on the immunological well-characterized C57BL/6J background. Intercrossing of heterozygous mice resulted in sub-Mendelian numbers of homozygous mice, suggesting loss of FANCG can be embryonic lethal. KO mice displayed infertility, hypogonadism but no other developmental problems. Bone marrow analysis revealed a defect in various hematopoietic stem and progenitor subsets with a bias towards myelopoiesis. Cell lines derived from Fancg-KO mice were hypersensitive to crosslinking agents-cisplatin and Mitomycin C, and Fancg-KO mouse embryonic fibroblasts (MEFs) displayed increased γ-H2AX upon cisplatin treatment. Reconstitution of these MEFs with Fancg cDNA corrected for the ICL hypersensitivity. Collectively, this project provides a new, genetically and immunologically well-defined Fancg-KO mouse model for further in vivo and in vitro studies on FANCG and ICL repair.

CRISPR-Cas9 technology allows the modification of DNA sequences in vivo at the location of interest. Although CRISPR-Cas9 can produce genomic changes that do not require DNA vector carriers, the use of transgenesis for stable integration of DNA coding for gene-editing tools into plant genomes is still the most used approach and it can generate unintended transgenic integrations, while Cas9 prolonged expression can increase cleavage at off-target sites. In addition, the selection of genetically modified cells from millions of treated cells, especially plant cells, is still challenging. These downfalls can be avoided with the delivery of preassembled ribonucleoprotein complexes (RNPs) composed of purified recombinant enzyme Cas9 and in vitro- transcribed guide RNA (gRNA) molecules in a protoplast system. We therefore aimed to develop the first DNA-free protocol for gene-editing in maize and introduced RNPs into their protoplasts with PEG 4000. We performed effective transformation of maize protoplasts using different gRNAs sequences targeting the inositol phosphate kinase gene and applying two different exposure times to RNPs. Using low-cost Sanger sequencing protocol, we observed an efficiency rate of 0.85 up to 5.85%, which is equivalent to DNA-free protocols used in other plant species. A positive correlation was displayed between exposure time and mutation frequency. Mutation frequency was gRNA sequence- and exposure time-dependent. In summary, we demonstrated the suitability of RNP transfection as an effective screening platform for gene-editing in maize. This efficient and relatively easy assay method for selection of gRNA suitable for editing of gene of interest will be highly useful for genome editing in maize, since genome size and GC-content are large and high in maize genome, respectively. Nevertheless, the large amplitude of mutations at target site requires scrutiny when checking mutations at off-target sites and potential safety concerns.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The article presents the results of the γ-ray and fast neutrons impact on various rice species, in order to obtain mutant forms resistant to salinity (NaCl) and drought factors (sorbite). They are going to be used as initial forms in synthetic selection when creating varieties, adapted to the stressful conditions of, both, soil and climate in the Kazakhstan Aral Sea. The average lethal doses (LD50) of γ-rays and fast neutrons, as well as, the average NaCl and sorbite lethal concentrations were established. A distinct dependence on the effect of ionizing radiation and stress factors on the number of induced resistant mutant forms has been related to the initial rice variety. The largest number of mutant forms was obtained from the local variety Syr Suluy, followed by Leader and Aikerim varieties. Out of all varieties, only 1% of the initially irradiated by γ-rays seeds survived, while after fast neutron irradiation – 4,3%. M1 mutant plants significantly differ from the initial forms in terms of morphological features – plant height, panicle length, and grain size. They are tolerant to lodging, and have short and highly sterile panicles, indicating that they are mutants.

1). BACKGROUND: Cell wall deficient mycobacteria (CWDM) have seldom been isolated in bacterial culture from human subjects. particularly in clinical disease, such as Crohn’s disease. Techniques have focused on the use of polymerase chain reaction (PCR) for the detection of CWDM in association with inflammatory bowel disease. (IBD). This paper is a report of the development of methods to demonstrate the presence of CWDM using the Ziehl-Neelsen (ZN) stain. This is in addition to the detection of the growth of CWDM in fluid media. 2). METHODS: The use of the ZN stain is suitable for the demonstration of CWDM in clinical samples and cultures, when the staining methods that were common prior to the 1970’s, are adopted. Specific culture media are developed and tested in parallel. Alterations in the concentration of basic fuchsin, and changes in the decolourising solutions are necessary. Decolourising solutions such as 20% concentrated sulphuric acid in water are preferable for detection of CWDM in cultures. 3). RESULTS: CWDM can be readily demonstrated using the simple methods outlined in this report. The ability to visualise the presence of CWDM opens the door to the development of specific fluid media for the isolation of CWDM in culture. 4). CONCLUSION: The ZN stain methods optimised for the demonstration of Mycobacterium tuberculosis complex (MTBC) are not suitable for research into infectious causes of inflammatory bowel disease (IBD), as well as for the detection of CWDM in latent tuberculosis. Revisiting the techniques for the detection of CWDM may also refocus attention on inflammatory diseases considered to be idiopathic, but having hallmarks of an infectious process.