Catalyst with high catalytic activity and good stability are desirable in the electrocatalytic oxidation of glucose. Herein, Pt concave nanocubes with high-index facets (HIFs) supported by carbon black (Pt CNC/CB) are prepared through a hydrothermal method. The experimental results demonstrate that the peak current densities in different potential regions on the Pt CNC/CB anode are 0.22, 0.20, and 0.60 mA cm−2, respectively. The glucose oxidation reaction shows superior performances in basic and neutral conditions than in acid conditions. Better stability is achieved by Pt CNC/CB than Pt concave nanocubes (Pt CNCs). Abundant surface defects with low-coordinated atom numbers, such as the steps, kinks, and edges, are served as active sites in the electrocatalytic oxidation of glucose. With the addition of carbon black, the catalytic activity can be improved by facilitating the full exposure of the active surface defects on the HIFs of Pt CNCs. Moreover, to address the aggregation of Pt CNCs, caused by the high surface energy of HIFs, the introduction of carbon material is an effective way to preserve the HIFs, and thus enhance the stability of the catalyst. Hence, the prepared Pt CNC/CB electrocatalyst has great potential to be applied in the electrooxidation of glucose.

Background: Telemonitoring systems in cardiology have shown potential in improving chronic cardiovascular disease (CVD) management. This study aims to evaluate the impact of telemonitoring, mainly through mobile applications, on patient outcomes such as self-care, blood pressure control, quality of life, and hospitalization. Methods: We systematically reviewed studies assessing telemonitoring methods for patients with chronic CVD. The analysis included studies from various geographic regions and healthcare settings, focusing on qualitative outcomes without performing a meta-analysis. Results: Telemonitoring was found to aid in maintaining blood pressure and significantly enhance self-care abilities. Improvements in quality of life were observed in some studies, though results varied. Most studies indicated telemonitoring could effectively manage blood pressure and reduce hypertension-related complications. However, the heterogeneity of interventions and outcomes measured across trials posed challenges for a comprehensive meta-analysis. Conclusions: Integrating telemonitoring systems into routine care can significantly improve disease management and patient outcomes for chronic CVD patients. Future research should standardize telemonitoring interventions and outcome measures, conduct long-term studies, and evaluate the cost-effectiveness of these systems. Greater blindness in future randomized controlled trials and more studies on atrial fibrillation are also necessary. Significant potential exists for telemonitoring to improve patient outcomes and assist in managing chronic illnesses.

The review analyzes a possible role of autoimmune processes in the pathogenesis of schizophrenia and evolution of concepts on this issue from its origin to present. Risks of autoimmune processes causing schizophrenia are associated with several factors: an impaired functioning of dopaminergic and glutamatergic systems in the brain, kynurenine pathway disorder with overproduction of quinolinic, anthranilic and kynurenic acids (possibly altering both neurons and T-regulators), increased intestinal permeability, as well as food antigens’ effects, stress and infections with various pathogens at different stages of ontogenesis. An increase in the levels of proinflammatory cytokines and chemokines as well as a decrease in the levels of anti-inflammatory ones also may contribute to schizophrenia risks. Schizophrenia often occurs in those patients having various autoimmune diseases and their first-degree relatives. Cases of schizophrenia resulted from autoimmune pathogenesis (including autoimmune encephalitis caused by autoantibodies against various neuronal antigens) are characterized by quite severe cognitive and psychotic symptoms and less favorable prognosis. This severe course may result from the chronic immune damage of the neuronal receptors such as NMDA, GABA, and others and depend on hyperprolactinemia, induced by antipsychotics, but aggravating autoimmune processes [with 2 tables, 4 figures, bibliography: 99 references].

Background: Despite its global eradication in 1977, smallpox remains a concern owing to its potential as a biological agent, thereby prompting the ongoing development and utilization of its vaccine. Vaccination with the Vaccinia virus induces immunity against variola virus, the causative agent of smallpox; however, this immunity does not extend to viruses of different genera within the Poxviridae family. In this study, we aimed to assess the efficacy of an enzyme-linked immunosorbent assay (ELISA) method utilizing Vaccinia virus and recombinant A27L antigen for detecting antibodies against smallpox. Methods. Analysis of serum from 20 individuals pre- and post-vaccination with the CJ strain (CJ50300) revealed neutralizing antibodies, which were confirmed using the plaque reduction neutralization test (PRNT). The ELISA method, validated with a PRNT50 cut-off value of >4, exhibited a sensitivity and specificity of >95% and was particularly reactive with the inactivated virus. Furthermore, adherence to the smallpox vaccination policy revealed significant differences in Orthopoxvirus antibody levels among 300 individuals of different age groups. These findings highlight the reliability and efficacy of the ELISA method in detecting post-vaccination antibodies and contribute significantly to diagnostic methods to prepare for potential smallpox resurgence and bioterrorism threats.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

In this study, in order to determine the effect of matrices shape on percolation threshold values, computer simulations were performed using the Monte Carlo method for a 200x200 square-shaped matrix and rectangular matrices containing the same number of nodes as the square matrix. Based on the simulations, the average values of percolation thresholds and standard deviations for current flow along and across the matrices were determined. It was determined that for a square-shaped matrix, the average values of percolation thresholds in both directions of current flow were the same. Extending the rectangular matrix while reducing its height causes the average value of the percolation threshold in the direction of current flow along the matrix to increase from 0.592740 to 0.759847, while in the transverse direction it decreases from 0.592664 to 0.403614. The values of the classical asymmetry coefficients of the probability distributions of percolation thresholds for both directions of current flow were determined. Histograms of the probability distributions of percolation threshold values for square-shaped matrix and rectangular matrices were made and compared with normal distributions. It was found that the occurrence of two percolation thresholds in rectangular layers should be considered when analyzing electrical conductivity measurements of nanocomposite thin films.

Cross-linked polyethylene (XLPE) is a highly all-important material renowned for its exceptional physical and chemical properties, and it is extensively utilized in various industries such as con-struction, piping, cable insulation and medical equipment. The cross-linking process of polyethylene involves chemical or physical bonding of polymer chains to enhance its resistance to heat, chemicals and mechanical stress. This study offers a comprehensive overview of recent research and potential advancements in this field, with a particular focus on the development of efficient techniques and environmentally sustainable cross-linking systems. It evaluates the opportunities and challenges faced by cross-linked polyethylene materials across diverse applications, providing valuable insights for future research in this area.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

The domestic ducks (Anas platyrhynchos domesticus) are resistant to most of the highly pathogenic avian influenza virus (HPAIV) infections. In this study, we characterized the lung proteome and phosphoproteome of ducks infected with HPAI H5N1 virus (A/duck/India/02CA10/2011/Agartala) at 12 hr, 48 hr and 5 days post infection condition. Total 2082 proteins were differentially expressed and 320 phosphorylation sites mapping to 199 phosphopeptides corresponding to 129 proteins were identified. Functional annotation of proteome data analysis reveals activation of RIG-I-like receptor and Jak-STAT signaling pathways, that lead to induction of interferon stimulated genes (ISGs) expression. The pathway analysis of phosphoproteome datasets also confirms the activation of RIG I, Jak-STAT signaling, NF-kappa B signaling and MAPK signaling pathways in the lung tissues. The induction of ISGs proteins (STAT1, STAT3, STAT5B, STAT6, IFIT5 and PKR) establishes protective antiviral immune response in duck lung tissue. Further, the protein-protein interaction network analysis identified proteins like AKT1, STAT3, JAK2, RAC1, STAT1, PTPN11, RPS27A, NFKB1 and MAPK1 as main hub proteins that might play important roles in disease progression in ducks. Together, functional annotation of proteome and phosphoproteome datasets reveals the molecular basis of the disease progression and disease resistance mechanism in ducks infected with HPAI H5N1 virus.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

The utilization and engineering of thermo-optic effects have found broad applications in integrated photonic devices, facilitating efficient light manipulation to achieve various functionalities. Here, we perform both an experimental characterization and theoretical analysis of these effects in integrated micro-ring resonators in high index doped silica (HIDS), which has had many applications in integrated photonics and nonlinear optics. By fitting the experimental results with theory, we obtain fundamental parameters that characterize their thermo-optic performance, including the thermo-optic coefficient, the efficiency for the optically induced thermo-optic process, and the thermal conductivity. The characteristics of these parameters are compared to those of other materials commonly used for integrated photonic platforms, such as silicon, silicon nitride, and silica. These results offer a comprehensive insight into the thermo-optic properties of HIDS based devices. Understanding these properties is essential for efficiently controlling and engineering them in many practical applications.

The paper examines the possibility of increasing the wear and corrosion resistance of a CP-Ti surface by duplex plasma electrolytic treatment (borocarburizing and polishing). The structure and composition of diffusion layers, their microhardness, surface morphology and roughness, wear resistance during dry friction and corrosion resistance in Ringer's solution were studied. The formation of a surface hardened layer up to 200 m thick with a microhardness of up to 950 HV, including carbides and a solid solution of boron and carbon, is shown. Subsequent polishing makes it possible to reduce surface roughness and remove weak areas of the porous oxide layer, which is formed during high-temperature oxidation in aqueous electrolyte vapor during borocarburizing. Changing the morphology and structural-phase composition of the CP-Ti surface helps reduce weight wear by 3 times (the mode of frictional interaction changes from microcutting to oxidative wear) and corrosion current density by 4 times after borocarburizing in a solution of boric acid, glycerin and ammonium chloride at 950 °C for 5 minutes and subsequent polishing in an ammonium fluoride solution at a voltage of 250 V for 3 minutes.

Artificial intelligence (AI) driven language models have seen a rapid rise in development, deployment, and adoption over the last few years. This surge has sparked many discussions about their societal and political impact, including political bias. Bias is a crucial topic in the context of large models due to its far-reaching consequences on technology, politics, and society. It significantly influences public perception, decision-making, political discourse, and AI policy governance and ethics. This study investigates political bias through a comparative analysis of four prominent AI models: ChatGPT-4, Perplexity, Google Gemini, and Claude.Through a comprehensive analysis by systematically and categorically evaluating their responses to politically and ideologically charged tests and prompts, utilizing the Pew Research Center’s Political Typology Quiz, the Political Compass assessment, and ISideWith political party quiz, this study identifies significant ideological leanings and the nature of political bias within these models. The findings revealed that ChatGPT-4 and Claude exhibit a liberal bias, Perplexity is more conservative, while Google Gemini adopts more centrist stances. The presence of such biases underscores the critical need for transparency in AI development and the incorporation of diverse training datasets, regular audits, and user education to mitigate these biases. This analysis also advocates for more robust practices and comprehensive frameworks to assess and reduce political bias in AI, ensuring these technologies contribute positively to society and support informed, balanced, and inclusive public discourse, which will point towards neutrality.The results of this study add to the ongoing discourse about the ethical implications and development of AI models, highlighting the critical need to build trust and integrity in AI models. Additionally, future research directions have been outlined to explore and address the complex issue of bias in AI.

The management of brain tumors presents numerous challenges, despite the employment of multimodal therapies including surgical intervention, radiotherapy, chemotherapy, and immunotherapy. Owing to the distinct location of brain tumors and the presence of the blood-brain barrier (BBB), these tumors exhibit considerable heterogeneity and invasiveness at a histological level. Recent advancements in hydrogel research for the local treatment of brain tumors have sought to overcome the primary challenge of delivering therapeutics past the BBB, thereby ensuring efficient accumulation within brain tumor tissues. This article elaborates on various hydrogel-based delivery vectors, examining their efficacy in the local treatment of brain tumors. Additionally, it reviews the fundamental principles involved in designing intelligent hydrogels that can circumvent the BBB and penetrate larger tumor areas, thereby facilitating precise, controlled drug release. Hydrogel-based drug delivery systems (DDSs) are posited to offer a groundbreaking approach in addressing the challenges and limitations inherent in traditional oncological therapies, which are significantly impeded by the unique structural and pathological characteristics of brain tumors.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

Soccer is the leading cause of all sports-related ocular injuries in Europe and Israel and leads to blindness at a disproportionately high rate, especially among children (Thompson et al., 2019). With soccer being the most popular sport in the world, it is surprising the only solution to ocular injuries are sports glasses which can cause direct damage to the eye and impair peripheral vision by 15%, calling for an alternative (Smith & Jones, 2020). This work, based on an imported facial model, focuses on both the qualitative and quantitative aspects of building a personalized, low-cost (through optimizing material needed), superior apparatus to conventional sports glasses. The quantitative side examines a modified and model-validated (through a SRS of thirty unique extrapolated points) multivariate linear regression equation, based on horizontal and vertical rotation angles (n=60) trained with residual and computer simulation data, that can accurately extrapolate and quantify ocular impact from all horizontal and vertical rotation angles and a modified Hertzian Contact Stress Equation to determine the thickness of the apparatus using the elasticity modulus, impact force, and geometrical facial and soccer-ball features. The qualitative side examines where firstly, ocular impact is most prevalent, and secondly, where most impact is seen from rotating the ball horizontally and vertically through analysis of Pearson’s Correlation Coefficient at the supraorbital, medial canthus, infraorbital, and lateral canthus regions from both regression equations as well as a cost-benefit analysis for comparison with conventional sports glasses. The findings discovered in this work lay the groundwork for future research to build a customized low-cost ocular injury prevention device which can simultaneously ensure complete ocular safety while enhancing athletic performance for over 250,000,000 players (Johnson & Garcia, 2022).

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

This paper introduces a class of symmetric ciphering systems with a finite secret key, which provides ideal secrecy, autonomy in key generation and distribution, and robustness against the probabilistic structure of messages (Ideally Secret Autonomous Robust – ISAR system). The ISAR system is based on wiretap polar codes constructed over an artificial wiretap channel with a maximum secrecy capacity of 0.5. The system autonomously maintains a minimum level of key equivocation by continuously refreshing secret keys without needing additional key generation and distribution infrastructure. Thus, this class of systems generalizes Shannon's ideal and strongly ideal ciphering systems. Additionally, it can transform any stream ciphering system with a finite secret key of known length into an ISAR system without the necessity of knowing and/or changing its algorithm. Therefore, this class of system strongly supports privacy, a critical requirement for contemporary security systems. The ISAR system's reliance on wiretap polar coding for strong secrecy ensures resistance to passive attacks with known plaintext messages. Furthermore, resistance to passive attacks on generated keys follows directly from ideal secrecy and autonomy. The results presented offer an efficient methodology for synthesizing this class of systems with predetermined security margins and a complexity of the order of nlogn, where n is the block length of the applied polar code.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

53% of adults in the US acknowledge racial bias as a significant issue, 23% of Asian adults experience cultural and ethnic bias, and more than 60% conceal their cultural heritage after racial abuse. AI models like ChatGPT and Google Bard, trained on historically biased data, inadvertently amplify racial and ethnic bias and stereotypes. This paper addresses the issue of racial bias in AI models using scientific, evidence-based analysis and auditing processes to identify biased responses from AI models and develop a mitigation tool. The methodology involves creating a comprehensive database of racially biased questions, terms, and phrases from thousands of legal cases, Wikipedia, and surveys, and then testing them on AI Models and analyzing the responses through sentiment analysis and human evaluation, and eventually creation of an 'AI-BiasAudit,' tool having a racial-ethnic database for social science researchers and AI developers to identify and prevent racial bias in AI models.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

The study aimed to investigate the impact of incorporating deep learning strategies in mathematics instruction on students' problem-solving abilities, critical thinking skills, academic achievement, and mathematical skills development. The study population consisted of 280 students, with a sample size of 162 participants. Employing a purely quantitative approach, data collection utilized questionnaires and achievement tests as instruments. Data analysis involved simple linear regression, descriptive analysis, and Pearson correlation. The results of the study revealed that there was no significant enhancement observed in students' problem-solving abilities and critical thinking skills when deep learning strategies were incorporated into mathematics instruction. Additionally, students' attitudes towards deep learning activities in mathematics showed no effect on their academic achievement. Furthermore, students' engagement levels in deep learning activities did not impact their development of mathematical skills. Lastly, the frequency of deep learning activities in the mathematics classroom did not show a significant relationship with students' academic performance. These findings suggest that the implementation of deep learning strategies in mathematics instruction did not yield notable improvements in the specified areas based on the study outcomes.

The purpose of this paper is to develop an index system for measuring the compliance of high-rise residential buildings with fire requirements and also to develop an index system for measuring the fire response efficiency, which is linked to the index of compliance with fire requirements. The higher the compliance rate, the greater the chance of a successful response. The two systems de-pend on the automation of the firefighting system management processes using the techniques of the fourth industrial revolution and developed based on the consultation of subject matter experts in the field. The main elements of the indexes were identified, which were based mainly on several variables, including the fire administrative system, the firefighting system, the residents, the loca-tion of the high-rise residential buildings from the fire extinguishing station, and the height of the high-rise residential building. The two systems can contribute to improving emergency prepared-ness in high-rise residential buildings in the Emirate of Sharjah and are also considered as a measurement index for compliance with fire requirements in the Emirate of Sharjah.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

This paper investigates five different GARCH models (GARCH, EGARCH, IGARCH, Component GARCH (CGARCH) and GJR-GARCH) along with six distributions (Normal, Student’s t, GED and their skewed forms), which are used to forecast the volatility for the Bulgarian Stock index SOFIX. We use a GARCH model to predict how much time it will take, after the latest crisis, for the SOFIX index to reach its historical peak once again. The empirical data covers the period between the years 2000 and 2024, including the 2008 financial crisis and the COVID-19 pandemic. The purpose is to answer which of the five models is the best at forecasting the volatility of SOFIX and which distribution is most appropriate. The results, based on BIC and AIC information criteria, show that the ARMA(1,1)-CGARCH(1,1) specification with the Student t-distribution is preferred for forecasting. With the help of 5000 simulations, it is estimated that the chances of Index SOFIX reaching its historical peak value of 1976.73 (08.10.2007) are higher than 90% at 13.08.2087.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

Carbon fiber-reinforced polymer (CFRP), noted for its outstanding properties including high specific strength and superior fatigue resistance, is increasingly employed in aerospace and other demanding applications. This study investigates the interactions between CFRP composites and high-energy lasers (HEL), with continuous wave laser powers reaching up to 120 kW. A novel automated sample exchange system, operated by a robotic arm, minimizes human exposure while enabling a sequence of targeted laser tests. High-speed imaging captures the rapid expansion of a plume consisting of hot gases and dust particles during the experiment. The research significantly advances empirical models by systematically examining the relationship between laser power, perforation times, and ablation rates. It demonstrates scalable predictions for the effects of high-energy laser radiation. Detailed examination of the damaged samples, both visually and via micro-focused computed X-ray tomography, offers insights into heat distribution and ablation dynamics, highlighting the anisotropic thermal properties of CFRP. Compression-after-impact (CAI) tests further assess the residual strength of the irradiated samples, enhancing the understanding of CFRP’s structural integrity post-irradiation. Collectively, these tests improve the knowledge of the thermal and mechanical behavior of CFRP under extreme irradiation conditions. The findings not only contribute to predictive modeling of CFRP's response to laser irradiation but also enhance the scalability of these models to higher laser powers, providing robust tools for predicting material behavior in high-performance settings.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

The present study is aimed at designing anti-reflective (AR) engraving on the Input-Output surfaces of a rectangular light-guide. We estimate AR efficiency, by the transmittance level in the angular range, determined by the light-guide. Using nano-engraving, we achieve a uniform high transmission over a wide range of wavelengths. In the past, we used smoothed conical pins or indentations on the faces of light-guide crystal as the engraved structure. Here, we widen the class of pins under consideration, following the physical model developed in the previous paper. We analyze the smoothed pyramidal pins with different base shapes. The possible effect of randomization of the pins parameters is also examined. The results obtained demonstrate optimized engraved structure with parameters depending on the required spectral range and facet format. The predicted level of transmittance is close to 99\%, and its flatness (estimated by the standard deviation) in the required wavelength range is 0.2\%. The theoretical analysis and numerical calculations indicate that the obtained results demonstrate the best transmission (reflection) we can expect for a facet with the given shape and size for the required spectral band. The approach is equally useful for any other form and of the facet. We also discuss a simple way of comparing experimental and theoretical results for a light-guide with the designed input and output features. In this study, as well as in our previous work, we restrict ourselves to rectangular facets. We also consider the limitations on maximal transmission produced by the size and shape of the light-guide facets. The theoretical analysis is performed for an infinite structure and serves as an upper bound on the transmittance for smaller-size apertures.

Annually, the oak forests of the Zagros Mountain chains, in western Iran and northeastern Iraq, face recurring challenges posed by forest fires, particularly in the Kurdo-Zagrosian forests situated in western Iran and northeastern Iraq. Assessing fire susceptibility relies significantly on vegetation condition. Integrating in situ data, Remote Sensing (RS) data, alongside the integration of Geographical Information Systems (GIS), presents a cost-effective and precise approach to capturing environmental conditions before, during, and after fire events, minimizing the need for extensive fieldwork. This study refines and applies the Zagros Grass Index (ZGI), a local vegetation index tailored to discern between grass-covered surfaces from tree canopies in Zagros forests, identifying the grass masses as the most flammable fuel type. Utilizing Moderate Resolution Imaging Spectroradiometer (MODIS) Normalized Difference Vegetation Index (NDVI) product as input, from 2013 to 2022, the ZGI aims to mitigate the influence of tree canopies, isolating NDVI values solely attributable to grass cover. By incorporating phenological characteristics of forest trees and grass species, the ZGI outperforms NDVI in mapping grass-covered areas that are crucial for fire susceptibility assessment in the study region. Results demonstrate a strong overlap between ZGI-based maps and recorded fire occurrences, validating the efficacy of the index in fire susceptibility estimation.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

Using the example of III-V nitrides crystallizing in a wurtzite structure (GaN, AlN, InN), this review presents the special role of hydrostatic pressure in studying semiconductor properties. Starting with a brief description of high pressure techniques for growing bulk crystals of nitride compounds, we focus on the use of hydrostatic pressure techniques in both experimental and theoretical investigations of special properties of nitride compounds, their alloys and quantum structures. The band gap pressure coefficient is one of the most important parameters in semiconductor physics. Trends in its behavior in nitride structures, together with trends in pressure-induced phase transitions, are discussed in the context of the behavior of other typical semiconductors. Using InN as an example, the pressure-dependent effects typical of very narrow bandgap materials, such as conduction band filling or effective mass behavior, are described. Interesting aspects of bandgap bowing in In-containing nitride alloys, including pressure and clustering effects, are discussed.Hydrostatic pressure also plays an important role in the study of native defects and impurities, as illustrated by the example of nitride compounds and their quantum structures. Experiments and theoretical studies on this topic are reviewed. Special attention is given to hydrostatic pressure and strain effects in short periods nitride superlattices. The explanation of the discrepancies between theory and experiment in the optical emission and its pressure dependence from InN/GaN superlattices led to the well-documented conclusion that InN growth on the GaN substrate is not possible. The built-in electric field present in InGaN/GaN and AlGaN/GaN heterostructures crystallizing in wurtzite lattice can reach several MV/cm, leading to drastic changes in the physical properties of these structures and related devices. It is shown how hydrostatic pressure modifies these effects and helps to understand their origin.

Achieving devices to be transparent is the task considered in the last time in many aspects and for different purposes. One issue of these problems is making anti-reflective surfaces in a wide wavelength range and keeping it flat enough. The authors of the previous publication showed that one could enhance a flat facet's transmission efficiency by suitable engraving. They used smoothed conical fingers and holes. Here, we widen the class of anti-reflective metasurfaces under consideration, following the requirements of the model developed in the previous paper. We involve also smoothed pyramidal fingers. The obtained results provide the improved engraved structure, with parameters dependent on the required spectral range, and the facet format. The predicted level of transmittance is close to 99\%, and the flatness(estimated by the standard deviation) as 0.2\%. This improvement is significant enough for high and broadband transmittance. In this work, we show that the randomization of the engraving parameters does not provide any significant effect for small facets. We also discuss a simple way of comparing experimental and theoretical results for a waveguide with the considered input and output features. In this study, as well as in our previous work, we restrict ourselves by rectangular facets. We also discuss the limitations that originated from the size and shape of the waveguide facets.

Abstract: The VSI represents a significant advancement in the assessment of gastrointestinal-specific anxiety among patients with Irritable Bowel Syndrome (IBS) and other Chronic Inflammatory Bowel Diseases (IBD). However, an Italian version of the instrument is not yet available for the reference population. This study utilized a national sample of 500 individuals, including healthy controls and patients with Ulcerative Colitis and Crohn's Disease, to test the validity and reliability of the Italian VSI. Using back-translation methodology to ensure translation fidelity, the research applied a questionnaire and the VSI through an online format to 500 participants. Data analysis revealed that the Italian VSI had excellent psychometric properties, demonstrating high internal consistency (Cronbach’s α = 0.95) and construct validity. The scale proved sensitive in detecting significant differences in visceral sensitivity among groups, highlighting its utility as a clinical and research assessment tool. Specifically, the Italian VSI exhibited a unidimensional factorial structure and maintained a strong correlation with other measures of anxiety and the severity of gastrointestinal symptoms, confirming its role in enhancing the understanding and management of IBS and IBD in Italy.

A plasmonic refractive index (RI) sensor based on metal-insulator-metal (MIM) waveguide coupled with concentric double rings resonator (CDRR) is proposed and investigated numerically. Utilizing the novel supermodes of the CDRR, the FWHM of the resonant wavelength can be modulated, and a sensitivity of 1060 nm/RIU with high figure of merit (FOM) 203.8 is realized in the near-infrared region. The unordinary modes as well as the influence of structure parameters on the sensing performance are also discussed. Such plasmonic sensor with simple framework and high optical resolution could be applied to on-chip sensing systems and integrated optical circuits. Besides, the special cases of bio- sensing and triple rings are also discussed.

Managing a portfolio whose value closely tracks an index by trading only in a subset of the index constituents involves an NP-hard optimisation problem. In the prior literature, it has been suggested to solve this problem using sequential Monte Carlo (SMC, a.k.a. particle filter) methods. However, this literature does not take transaction costs into account, although transaction costs are the primary motivation for attempting to replicate the index by trading in a subset, rather than the full set of index constituents. This paper extends the SMC approach to index tracking to allow for proportional transaction costs and implements this extended method on empirical data for a variety stock indices. In addition to providing a more practically useful tracking strategy by allowing for transaction costs, we find that including a penalty for transaction costs in the optimisation objective can actually lead to better tracking performance.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

Despite significant advancements in Artificial Intelligence (AI) and Large Language Models (LLMs), detecting and mitigating bias remains a critical challenge, particularly within social media platforms like X (formerly Twitter) and in addressing cyberbullying present on them. This research investigates the effectiveness of leading LLMs in generating synthetic biased and cyberbullying data and evaluates the proficiency of Transformer AI models in detecting bias and cyberbullying within both authentic and synthetic contexts. The study involves semantic analysis and feature engineering on a dataset of over 48,000 sentences related to cyberbullying collected from Twitter (before it became X). Leveraging state-of-the-art LLMs such as ChatGPT-4o, Pi AI, Claude 3 Opus, and Gemini-1.5, synthetic biased, cyberbullying, and neutral data were generated to deepen the understanding of bias in human-generated data. AI models including DeBERTa, Longformer, BigBird, HateBERT, MobileBERT, DistilBERT, BERT, RoBERTa, ELECTRA, and XLNet were initially trained to classify Twitter cyberbullying data and subsequently fine-tuned, optimized, and quantized for multilabel classification (detecting both biases and cyberbullying). The study's outcomes include a prototype of a hybrid application that combines a Bias Data Detector and a Bias Data Generator, validated through extensive testing.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from <5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

.Bacground: Sepsis remains a major health challenge worldwide, characterized by a dysre-gulated host response to infection, leading to high mortality and morbidity in intensive care units (ICUs). The Fibrosis 4 (FIB-4) index, originally developed to assess liver fibrosis in hepatitis C patients, has recently been explored for its potential prognostic value in sepsis patients. Method: This study retrospectively analyzed 309 sepsis patients admitted to the Internal Me-dicine and Anaesthesia ICUs between December 12, 2021, and December 15, 2023, to inves-tigate the relationship between FIB-4 levels, Acute Physiology and Chronic Health Evaluation (APACHE), and Sequential Organ Failure Assessment (SOFA) and clinical outcomes. Results: The study found that higher FIB-4 measurements were statistically significantly asso-ciated with increased 28-day mortality, with a cut-off value of 4.9 providing a sensitivity of 54.92% and specificity of 74.25%. Logistic regression analysis indicated that elevated Conclusion:FIB-4 levels were a significant predictor of early mortality, suggesting that the FIB-4 index could serve as a valuable prognostic tool in assessing the severity and prognosis of sepsis patients.

Rapid urbanisation and city expansion worldwide have significantly increased impervious surfaces such as roads, buildings, and pavements. These impervious surfaces impede water infiltration into the ground, resulting in escalated surface runoff during rainfall. This has been exacerbated by climate change and heightened precipitation levels, resulting in recurrent annual flooding. Conventional drainage systems are now insufficient to cope with the amplified surface runoff, contributing to the escalating flood occurrences. Sustainable urban drainage systems such as green roofs, swales, and permeable pavements were developed as modern flood control techniques to replace the traditional drainage system approach by optimising resource utilisation and developing novel and more productive technologies. While most SUD techniques are sustainable in design, construction, and operation, permeable pavements are considered one of the least sustainable SUD techniques. This has garnered considerable attention from researchers who have been studying the design of a more sustainable permeable pavement system by utilising sustainable and recycled materials. This paper reviews the performance of permeable pavements systems using findings from extensive reviews and analyses of scientific publications on permeable pavements. It introduces a future solution and design of permeable pavements using recycled materials. The study will consist of two permeable pavement systems, one incorporating recycled materials in its layers and the other using traditional construction materials. The data collected from both systems will be compared to determine their performance.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

:. Background and Objectives: Pulmonary embolism, PE, incidence had been increasing in the last ten years. Computed thoracic pulmonary angiography, CTPA, had a major role in confirming PE di-agnosis.The main purpose of the study was to establish the prognostic value of a CTPA parameter: pulmonary artery obstruction index, PAOI, for PE risk assessment . A second objective of the re-search was to investigate the predictive accuracy of biomarkers (D-dimer, and cardiac Troponin T, c-TnT ), and PAOI, in 7-day mortality. The third objective of the study was the relationship between PAOI, and these biomarkers, in different etiologies of PE. Materials and Methods: The study com-prised 109 patients with PE, hospitalized, and treated between February 2021, and August 2022. They had different etiologies: deep vein thrombosis, DVT; persistent atrial fibrillation, AF; chronic obstructive pulmonary disease, COPD, exacerbation; Covid; and cancers. The investigations were the following: clinical examination; D-dimer testing, as a mandatory method for PE suspicion( values ≥ 500 µg/L were highly suggestive for PE); c-TnT , as a marker of myocardial injury(values ≥ 14 ng/L were abnormal); CTPA, with right ventricle dysfunction, RVD, signs, and PAOI. Treat-ments were according to PE risk: systemic thrombolysis (in high risk , and hemodynamic instability); low weight molecular heparins, LWMH, after systemic thrombolysis, or in high risk PE, with he-modynamic stability; direct oral anticoagulants, DOAC (in low, and intermediate risk). Results: The relationship PAOI- D-dimer, and PAOI- c-TnT, had very strong statistical correlation, for the entire sample, and for DVT, AF, COPD, Covid subgroups ( Rho = 0.815-0.982). PAOI had a high predic-tive accuracy for intermediate , and high risk together (area under curve, AUC=0.948), and high risk PE (AUC= 0.993). For 7-day mortality, D-dimer , and c-TnT had high predictive accura-cy(AUC=0.921, and 0.979). PAOI had statistical significance for 7-day mortality in Covid (p=0.045), and cancer (p=0.038) patients. Conclusions: PAOI was an important tool for PE risk as-sessment. D-dimer , and c-TnT were valuable predictors, for 7-day mortality in PE. PAOI, and D-dimer; PAOI, and c-TnT were strongly correlated, for the entire PE sample, and for DVT, AF, COPD, and Covid patients.

In this paper, we focus on the impact of financial liberalization on stability of emerging stock market. We identify crises in a group of Latin American (Argentina, Brazil and Chile) and Asian countries (Philippines, Korea, Taiwan and Thailand) during 1975–2005. This paper aims to apply the methodology of CMAX method. Our results indicate that liberalization triggers more unstable stock market in the short run and generate several crises. Still, liberalization seems to generate more stable financial markets in the long run. Financial liberalization does not increase the frequency of crises in emerging countries and at long-term, crises are less several.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Background: The Advanced Lung Cancer Inflammation Index (ALI) is a novel, comprehensive index that integrates inflammation and nutritional status, incorporating parameters such as albumin, body mass index (BMI), and the neutrophil-to-lymphocyte ratio (NLR). Unlike traditional inflammation biomarkers, this study aims to evaluate the prognosis of IPF patients by considering both inflammation and nutritional status. Method: A total of 102 patients with IPF were included in the study. Clinical data were obtained from the patients’ medical records. NLR and ALI score were calculated based on data collected at the initiation of antifibrotic treatment using the following formula: Neut/Lym and albumin × BMI / NLR. Results: IPF subject subgroups in terms of ALI based on gender–age–physiology (GAP) stages (1,2,3), FVC (median split, <70% vs ≥70%), DLCO (<51% vs ≥51%), 6-Minute Walk Test (6MWT) (<350 vs ≥350) and CCI (≤1 vs >1). ALI showed significant difference depending on the categories of GAP stage, FVC, DLCO, and 6MWT but these differences were not observed based on the charlson comorbidity index (CCI) categories (sırasıyla p=0.000, p=0.000, p=0.000, p=0.001, p=0.233). Receiver Operating Characteristic (ROC) curve analysis was performed to evaluate the sensitivity and specificity of ALI, albumin, NLR, and BMI in determining the mortality risk in IPF patients. ALI demonstrated a sensitivity of 63.6% and a specificity of 98.9% at a threshold of 11.2 (AUC = 0.945, 95% CI 0.892–0.998, p < 0.000). Conclusion: We determined that ALI levels are significantly associated with disease severity and mortality in patients with IPF.

Background: A prognostic index validated for the outcomes of advanced high-grade serous ovarian cancer (HGSOC) patients with neoadjuvant chemotherapy (NACT) is still lacking. We therefore developed an ovarian neoadjuvant chemotherapy prognostic index (ONCPI) to enhance predictive accuracy. Methods: We analyzed clinicopathologic feature of advanced HGSOC patients receiving platinum-based NACT. Blood inflammatory composite markers were calculated and binary-transformed by optimal cutoffs. The omental hematoxylin and eosin (H&E) stained slides were selected for the assessment of chemotherapy response score (CRS). Logistic regression analyses and Cox proportional hazard regression model were utilized to develop a prognostic index. Results: Multivariate analysis showed that CRS and neutrophils-to-lymphocyte ratio (NLR) are independent risk factors for platinum-chemotherapy response. Meanwhile, Kaplan–Meier and Cox regression analysis revealed that CRS score was significantly correlated with PFS and OS, and NLR-high patients was associated with poor OS. We further developed an ONCPI model based on the CRS score and NLR level. Survival analysis suggested that patients with score 0 and 1 of ONCPI were significantly associated with improved PFS and OS. Conclusions: The ONCPI score emerges as a significant prognostic marker for predicting NACT outcomes in advanced HGSOC patients. Its integration into clinical practice and risk-stratified trial design is conceivable.

In the paper the verification of forecasts of precipitation conditions measured by the standardized precipitation index SPI is presented. For the verification of categorical forecasts a contingency table was used. Standard verification measures were used for the SPI value forecast. The 30 day SPI moved every 10 days by 10 days was calculated in 2013-2015 from April to September on the basis of precipitation data from 35 meteorological stations in Poland. Predictions of the 30 day SPI were created in which precipitation was forecasted in the next 10 days (the SPI 10-day forecast) and 20 days (the SPI 20-day forecast). Both for the 10 and 20 days, the forecasts were skewed towards drier categories at the expense of wet categories. There was a good agreement between observed and 10-day forecast categories of precipitation. Less agreement is obtained for 20-day forecasts – these forecasts evidently “over-dry” the assessment of precipitation anomalies. The 10-day SPI value forecast accuracy is acceptable, whereas for the 20-day forecast is unsatisfactory. Both for the SPI categorical and the SPI value forecast, the 10-day SPI forecast is reliable and the 20-day forecast should be accepted with reservation and used with caution.

Recent analyses of cosmic microwave background surveys have revealed hints that there may be a non-trivial running of the running of the spectral index. If future experiments were to confirm these hints, it would prove a powerful discriminator of inflationary models, ruling out simple single field models. We discuss how isocurvature perturbations in multi-field models can be invoked to generate large runnings in a non-standard hierarchy, and find that a minimal model capable of practically realising this would be a two-field model with a non-canonical kinetic structure. We also consider alternative scenarios such as variable speed of light models and canonical quantum gravity effects and their implications for runnings of the spectral index.

Several studies have shown promising treatments for type 1 diabetes mellitus (T1DM) using developing gene therapy methods. This review article focuses on summarizing possible new treatment options and outlining their pros and cons, since there is no cure for T1DM as of yet. New treatments involve islet and stem cell transplantation, genetic vaccination, and immunological precursor cell-mediated therapy. Since most of these methods are still in their early stages, efficacy in human trials of this type of treatment is still largely unknown, however, researchers are hopeful after numerous successes in trials with non-obese diabetic (NOD) mice.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

Purpose: The purpose of this study is to apply the Composite Radiographic Index modified (CRIm) in CBCT scans of patients with Medication related osteonecrosis of the jaws (MRONJ) in order to detect its validity, and corelate the radiologic findings with the clinical staging of the disease. Methods: This study included 43 patients with MRONJ diagnosis and CBCT scans performed in the School of Dentistry and approved by the Research Ethics Committee. Clinical staging for every patient (0-3) was provided according to AAOMS 2022 guidelines. In cases of patients with both jaws affected, each jaw was evaluated independently resulting to 52 CBCT scans. The 52 CBCT scans were assessed under standardized viewing conditions by 2 observers who evaluated independently the following 8 radiologic features: lytic changes, sclerosis, periosteal reaction, sequestration, non-healing extraction sockets and other findings (sinus implication, inferior alveolar canal involvement, jaw fracture). The CRIm index was constructed to assess the extent of osseous changes. The radiologic features were scored as absent (0), localized/single (1), extensive/multiple (2), yielding a theoretical range of 0–12. For statistical analysis Fisher’s exact test and Spearman’s correlation coefficient were performed. Results: A statistically significant association of clinical stage with lytic changes, sequestration and inferior alveolar canal involvement was found. Also, a statistically significant correlation of clinical stage with CRIm index classification was obtained. Conclusions: The CRIm index tends to increase as the clinical stages of MRONJ advance, suggesting a correlation between the clinical stage of MRONJ and the CRIm index.

COPD is currently the fourth leading cause of death in the world. Globally, due to continued exposure to COPD risk factors and an aging population, the burden of COPD is expected to increase in the coming decades. The BODE (body mass index, airflow obstruction, dyspnea, and exercise capacity) index is a practical and multidimensional predictor for prognosis of COPD, and better than FEV1.We used the database of Kaohsiung Chang Gung Memorial Hospital medical center, Taiwan to analyze the correlation between BODE index, healthcare resource utilization, and Charlson comorbidity index (CCI). This retrospective study to collect COPD patients with complete BODE index data who had undergone a 6-minute walk examination in our hospital from January 2015 to December 2016. The medical cost and comorbidities database were analyzed from January 1, 2015, to August 31, 2017. Of 396 patients, 382 (96.5%) were male, with an average age of 71.3 ± 8.4 years. There was a significant association between the BODE index and the CCI of COPD patients (p < 0.001). Healthcare resource utilization was positively correlated with the BODE index during the 32 months of retrospective clinical outcomes: positively correlated with the number of hospitalizations (p<0.001), hospitalization days (p<0.001), hospitalization expenses (p=0.005), and total medical expenses (p=0.024), respectively. Our findings provide the crucial information for clinician to predict medical burden and comorbidities in patients with COPD by using BODE index.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

Lipids have not traditionally been considered likely candidates for catalyzing reactions in biological systems. However, there is significant evidence that aggregates of amphiphilic compounds are capable of catalyzing reactions in synthetic organic chemistry. Here we demonstrate the potential for the hydrophobic region of a lipid bilayer to provide an environment suitable for catalysis by means of a lipozyme, or lipid aggregate capable of speeding up a chemical reaction. By bringing organic molecules into the non-polar or hydrophobic region of a lipid bilayer, reactions can be catalyzed by collections of small, nonpolar or amphiphilic molecules. We demonstrate this concept by the ester hydrolysis of calcein-AM to produce a fluorescent product, which is a widely used assay for esterase activity in cells. The reaction was first carried out in a two phase octanol-water system with the organic phase containing the cationic amphiphiles cetyltrimethylammonium bromide (CTAB) or octadecylamine. The octanol was then replaced with DOPC added to the water in the form of vesicles, where the reaction was also found to be carried out. The reaction was monitored using quantitative fluorescence which revealed catalytic turnover numbers on a scale of 10−4s−1 for each system, which is comparable to some slow enzymes. The reaction product was characterized by 1H-NMR measurements which were consistent with ester hydrolysis. The implications of thinking about lipid aggregates as catalytic entities are discussed in the context of biochemistry, pharmacology and synthetic biology.

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

High-power lasers play an important role in modern science, industry, and medicine. A signifi-cant milestone was reached on December 5, 2022, when Inertial Confinement Nuclear Fusion (ICF) achieved scientific breakeven, releasing more energy than the input laser energy. Additionally, Extreme Ultraviolet Lithography (EUVL) has enabled the development of microchips with 3 nm process nodes, marking a leap in semiconductor technology. These examples together with the recent achievement of a 10 PW (1015 W) laser output heralds remarkable advancements in technology and science soon. Laser systems are broadly classified based on their operating re-gimes into two main categories: Continuous Wave (CW) operation, where the laser is continuously pumped and emits a steady beam of light, and the pulsed regime, in which the laser pro-duces single or multiple pulses at various repetition rates. This review will primarily focus on pulsed laser systems, exploring their various types and recent technological advancements.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Background: Obesity remains a widely debated issue, often criticized for the limitations in its identification and classification. This study aims to compare two distinct systems for classifying obesity: Body Mass Index (BMI) and body fat percentage (BFP) as assessed by bioelectrical impedance analysis (BIA). By examining these measures, the study seeks to clarify how different metrics of body composition influence the identification of obesity-related risk factors. Methods: The study enrolled 1255 adults, comprising 471 males and 784 females, with a mean age of 36 ± 11.90 years. Participants exhibited varying degrees of weight status, including optimal weight, overweight, and obesity. Body composition analysis was conducted using the TANITA Body Composition Analyzer BC-418 MA III device (T5896, Tokyo, Japan), evaluating the following parameters: current weight, basal metabolic rate (BMR), adipose tissue (%), muscle mass (%), and hydration status (%). Results: Age and psychological factors like cravings, fatigue, stress, and compulsive eating were significant predictors of obesity in the BMI model but not in the BFP model. Additionally, having a family history of diabetes was protective in the BMI model (OR: 0.33) but increased risk in the BFP model (OR: 1.66). The BMI model demonstrates exceptional predictive ability (AUC=0.998). In contrast, the BFP model, while still performing well, exhibits a lower AUC (0.975), indicating slightly reduced discriminative power compared to the BMI model. Conclusions:BMI classification demonstrates superior predictive accuracy, specificity, and sensitivity. This suggests that BMI remains a more reliable measure for identifying obesity-related risk factors compared to the BFP model.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Wheeled mobile robot dynamics and suitable controller design are challenging but rewarding fields of study. By understanding the dynamics of wheeled mobile robots, it could be possible to design suitable hybrid control schemes for wheeled mobile robots. Since hybrid control schemes involve combining individual control methods to create a more effective overall control strategy. This can be done in a variety of ways, such as using fuzzy linear quadratic Gaussian control. We were therefore inspired to create dynamic models and their controller designs for the wheeled mobile robot by examining the dynamics of the wheeled mobile robot. The novelty of the current paper is to hybridize the different control schemes for wheeled mobile robots in order to get better performance. Entire systems models were simulated in a MATLAB/SIMULINK environment. The results obtained for the settling time response by FLQG were 87.1% over LQG; this study compared the effectiveness of current and previous FLQG controllers in external disturbances and found peak amplitude improvements of 71.25%. Therefore, the proposed controller is suitable for use with the wheeled mobile robot.

Abstract: Doppler renal resistive index (RRI) has been used for several decades as a potential indi-cator for renal disease and progression. In recent years, RRI has emerged as a useful prognostic indicator for a range of co-morbidities in patients who are acutely unwell and as a potential marker for sub-clinical acute kidney injury (AKI) and post procedural AKI risk. Despite this, the clinical and theoretical determinants of RRI are poorly understood and remain contentious. Method: A narrative review of studies exploring the theoretical, experimental, and clinical evidence for factors affecting RRI. No date restrictions were set. Findings: Both experimental and clinical data confirm that RRI is markedly affected by a range of systemic and renal determinants and is influenced closely by the underlying risk factors and sys-temic vascular changes that lead to progressive renal damage. Discussion: This paper provides an overview of the key haemodynamic determinants of renal re-sistive index and aims to clarify their relative importance. With reference to a simplified theoretical model, evidence from experimental and clinical studies is reviewed. Pathophysiological factors and patient characteristics that influence RRI are explored to provide a better understanding of why RRI values change in the presence of common or complex pathologies. Conclusion: By gaining a better understanding of the complex systemic and renal factors that influ-ence RRI, ultrasound users will be better prepared to understand and interpret changes in RRI across a range of patient presentations.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

This paper introduces an innovative Particle Swarm Optimization (PSO) Algorithm in-corporating Sobol and Halton Random number samplings. It evaluates the enhanced PSO's performance against conventional PSO employing Monte Carlo Random Number Samplings. The comparison involves assessing the algorithms across nine benchmark problems and the renowned Travelling Salesman Problem (TSP). The re-sults reveal consistent enhancements achieved by the enhanced PSO utilizing Sob-ol/Halton samplings across the benchmark problems. Particularly noteworthy are the substantial improvements demonstrated by the enhanced PSO in solving the Travel-ling Salesman Problem. These findings underscore the efficacy of employing Sobol and Halton random number generation methods in enhancing algorithm efficiency.

Historical maps possess significant theoretical and practical value in fields such as historical geography and urban planning, making them essential tools for studying urban spatial structure. This study explores the evolution of Xi'an's urban spatial structure from the Five Dynasties (909 CE) to the late PRC period (1949 CE), using historical maps and Historical GIS (HGIS) methodologies. By integrating Space Syntax and Kernel Density Estimation (KDE) with data from The Historical Atlas of Xi'an, this research identifies key trends in the city's spatial transformation. Two distinct phases of development were observed: the simpler, centralized structure during the Five Dynasties, Northern Song, and Yuan periods, and a more complex, decentralized structure during the Ming, Qing, and PRC periods. These changes were influenced by a dynamic interplay of political, economic, cultural, and environmental factors, as well as the city's need to adapt to external military threats and internal socio-economic shifts. The study emphasizes the value of HGIS in analyzing urban historical geography and the potential it offers for both understanding past urban dynamics and informing contemporary urban planning and cultural heritage preservation efforts. The findings demonstrate how Xi'an's spatial evolution reflects broader trends in Chinese history and provides insights for future sustainable development.

This study aims to investigate whether 16 weeks of High-Intensity Interval Training (HIIT) implemented on Physical Education classes (PEC), can improve physical fitness in high-school adolescents This study was a two-arm randomized controlled trial design with adolescents (15-17 years old). Twelve classes were randomized to either a 16 weeks of HIIT (HIIT-G, n = 106 students) implemented on PEC warm-up or a control group (CG, n = 123 students) of usual PEC warm-up. The HIIT sessions ranged from 14 to 20 all-out bouts intervals, adopting a 2:1 work-to-rest ratio. Post-intervention measures revealed a significant difference between groups in CRF and girls from HIIT-G increased their cardiorespiratory fitness (CRF) with significant difference between female groups and a medium to large effect size. The main findings from this study indicate that brief whole-body HIIT of an extremely low volume, over 16 weeks, can improve CRF in adolescent girls.

Droughts have negative impacts on agricultural productivity and economic growth. Effective monitoring and accurate forecasting of drought occurrences and trends are crucial for minimizing drought losses and mitigating their spatial and temporal effects. In this study, trend dynamics in monthly total rainfall time series measured at Cape Town International Airport were analyzed using Mann-Kendall (MK) test, Modified Mann-Kendall (MMK) and innovative trend analysis (ITA) were examined. Additionally, we utilized hybrid prediction method that combined the model with the complementary ensemble empirical mode decomposition with adaptive noise (CEEMDAN) technique, the autoregressive integrated moving average (ARIMA) model, the long short-term memory (LSTM) network (i.e. CEEMDAN-ARIMA-LSTM) to forecast SPI values of 6-, 9-, and 12-months using rainfall data between 1995 and 2020 from Cape Town International Airport meteorological rainfall stations. The results demonstrate the following essential points: (1) The trend analysis results of the total monthly rainfall values indicate a significant decreasing trend with the negative z-score (MK= -3.7541 and MMK= - 4.0773). ITA also indicated a significant downwards trend of rainfall in the study area. (2) As the forecasting horizon increases, the prediction accuracy of the models and CEEMDAN-combined models gradually improves, reaching their optimum performance at the 12-month horizon. (3) CEEMDAN efficiently stabilizes time-series data, resulting in greater prediction accuracy in the hybrid model compared to individual models at all timescales. (4) The RMSE and R2 values for the hybrid CEEMDAN-ARIMA-LSTM model at a 12-month forecasting horizon are 0.042 and 0.995, demonstrating the applicability of this hybrid approach for drought forecasting.

Objective: To analyse the association between maternal risk factors such as age, body mass index (BMI) and cigarette smoking, with perinatal outcomes. Materials and Methods: This a retrospective analysis from prospectively collected data performed at Hospital Universitario de Torrejón (Madrid, Spain), between September 2017 and December 2019. All pregnant women with singleton pregnancies and non-malformed live fetuses attending their routine ultrasound examination at 11+0 to 13+6 weeks' gestation were invited to participate. Association between preeclampsia, preterm birth, gestational diabetes mellitus (GDM), small for gestational age (SGA) or fetal growth restricted (FGR) neonates and type of delivery according to maternal age, BMI, and cigarrete smoking was studied. Logistic mixed models were used to analyze the data. Results: 1921 patients were included in the analysis. Women of 40 years old had a significantly higher risk of having GDM (Odds Ratio (OR) 1.61, 95% Confidence Interval (CI) 1.08 to 2.36), and SGA neonates (OR 1.54, 95% CI 1.00 to 2.37). Women with a BMI &lt;18 had an increased rate of birth SGA and FGR neonates (OR 3.28, 95% CI 1.51 to 7.05, and OR 3.73, 95% CI 1.54 to 8.37, respectively), whereas women with a BMI ≥35 had a higher risk of GDM (OR 3.10, 95% CI 1.95 to 4.89). Smoking increased the risk of having SGA and FGR neonates (OR 1.83, 95% CI 1.36 to 2.46, and OR 1.91, 95% CI 1.29 to 2.78). Conclusions: Advanced maternal age, low or high BMI, and smoking status are significant risk factors for pregnancy complications. Both clinicians and society should concentrate their efforts on addressing these factors to enhance reproductive health.

The fetal splenic artery pulsatility index (PI) is a parameter that reflects fetal well-being and has been used as a predictor of adverse pregnancy outcomes. The aim of this study was to investigate the predictive value of splenic artery PI in GDM class A1 cases for NICU admission. In this prospective case controlled study, only sixty single pregnancy cases diagnosed with gestational diabetes mellitus class A1 were evaluated. Fetal splenic artery Doppler parameters Peak systolic velocity (PSV), Pulsatility index (PI), Resistivity index (RI) and End diastolic velocity (EDV) were measured in all cases. The rate of re-quirement of need of neanoatal intensive care unit was noted. In cases with need fetal intensive care, fetal splenic PI index was found to be statistically significantly lower than in healthy cases without it (0.94 ± 0.29 vs. 1.70 ± 0.53, respectively, p

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Students have historically fared poorly on the West African Examinations Council’s (WAEC) mathematics exam. This study investigated senior high school students’ difficulties with studying Geometry in the Cape Coast Metropolis, Central Region, Ghana. Using the descriptive survey design, data were collected from 300 Senior High School Two (SHS 2) students using simple random sampling. Students responded to the questionnaire and a 30-item multiple-choice achievement test on geometry. Four geometry concepts students perceived difficult to study are Circle theorems, Perpendicularity of Tangent and radius of a circle, Angle between Tangent and a chord and Tangents from an external point. The reasons for the difficulty in studying geometry topics are the unavailability of instructional materials, the geometry topics being complex, and teachers not teaching geometry concepts to the students’ understanding. Students’ gender did not influence the learning of concepts in geometry at a 0.05 level of significance. There was an insignificantly weak positive correlation between the students’ performance and their perceived difficult geometry concepts. It was concluded that the Ministry of Education does not provide relevant instructional materials to the various schools to teach geometry concepts. Schools do not organise workshops and seminars for teachers on effectively teaching geometry concepts in mathematics.

Droughts are a common occurrence in various climates and are primarily caused by a prolonged decrease in rainfall. Several factors contribute to droughts, including temperature, wind speed, relative humidity, rainfall timing, amount, and intensity during the growing season. The objective of this study is to establish a new index, named soil moisture and evapotranspiration revealed drought index (SERDI), for displaying dry and wet conditions based on combining both soil moisture and evapotranspiration (Penman-Monteith) to improve drought early warning and its severity globally. For validation of the SERDI with other indices such as LST, VHI, NDVI, and NDWI, different ways used such as R-square, RMSE, MAPE, and P-value to estimate the accuracy, variability of data, the forecast conditions, and how the significance of data. The results showed that the low RMSE and high r² were found between SERDI with LST and VHI. In contrast, the low R- square and high RMSE were between SERDI with NDVI and NDWI in most of the semi-arid areas. Furthermore, most of the semi-arid areas from Iran, Iraq, Syria, Jordan, and Israel experienced moderate and severe dry conditions, except some parts of these regions had normal conditions in Iran and Syria. The SERDI analysis revealed a strong correlation between (LST) and a moderate correlation with (VHI) across all study areas. However, the relationship between other indices, like (NDWI) and (NDVI), varied depending on the regions. To conclude, SERDI can be used globally for detecting drought based on soil moisture and evapotranspiration.

A binary biomass-based solid electrolyte film (LSE) was successfully synthesized through the incorporation of lignin nanoparticles (LNP) with sodium alginate (SA). The impact of the mass ratio of SA to LNP on the microstructure, porosity, electrolyte absorption capacity, ionic conductivity, and electrochemical properties of the LSE was thoroughly investigated. The results indicated that as the proportion of SA increased from 5% to 15% LNP, the pore structure of the LSE became increasingly uniform and abundant. Consequently, enhancements were observed in porosity, liquid absorption capacity, ionic conductivity, and overall electrochemical performance. Notably, at a SA amount of 15% LNP, the ionic conductivity of resultant LSE-15 was recorded at 14.10 mS cm1, with porosity and liquid absorption rates reaching 308% and 58.4%, respectively. LSE-15 was employed as a solid electrolyte, while LNP-based carbon aerogel (LCA) served as the two electrodes in the construction of a symmetric all-solid-state supercapacitor (SSC). The SSC device demonstrated exceptional electrochemical storage capacity, achieving a specific capacitance of 197 F g1 at 0.5 A g1, along with maximum energy and power density of 27.33 W h kg1 and 4998 W kg1, respectively. Furthermore, the SSC device exhibited highly stable electrochemical performance under extreme conditions, including compression, bending, and both series and parallel connections. Therefore, the development and application of the binary biomass-based solid electrolyte film in supercapacitors represent a promising strategy for harnessing high-value biomass resources in the field of energy storage.

Aim: This study aimed to evaluate the effectiveness of a plyometric training program designed to enhance agility, speed, and social interaction among boys with mild intellectual disability (ID) aged 10-12, within the Special Olympics framework. Participants: Thirty-two boys (mean age = 10.69 ± 0.8 years; mean IQ = 61 ± 7) from three inclusive education centers participated in the study. Methods: The intervention consisted of a 10-week plyometric training program, conducted twice a week. Pre- and post-intervention assessments included the Reaction Time Test, 4-Corner Agility Test, 10-Meter Speed Run, 4x5 Meter Relay Test, and the Friendship Activity Scale (FAS). Results: The study found significant improvements across all measures. Reaction time decreased by 0.83 seconds (t = 7.44, p < 0.001), 4-corner agility improved by 0.77 seconds (t = 11.93, p < 0.001), 4x5 meter speed improved by 0.61 m/s (t = 17.37, p < 0.001), and 10-meter run speed improved by 1.55 m/s (t = -12.76, p < 0.001). Additionally, the FAS score increased by 0.81 points (t = 9.59, p < 0.001), indicating enhanced social interactions. Conclusion: The plyometric training program significantly improved agility, speed, and social interaction in children with mild ID, demonstrating the effectiveness of inclusive, adaptive physical education strategies within the Special Olympics framework.

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

(1) Background: Parents of children with autism spectrum disorders often experience psychological distress, which can affect the quality of childcare they provide. It is crucial to screen for psychiatric symptoms among these parents. The Core Symptom Index (CSI) is a widely used tool for assessing general symptoms such as depression, anxiety, and somatic symptoms, with demonstrated validity and reliability across various populations. However, there is limited research on the validity and reliability of the CSI in the general Chinese population. This study aimed to investigate the psychometric properties of the Chinese version of the CSI among parents of children with autism spectrum disorders using Confirmatory Factor Analysis (CFA). (2) Methods: A total of 794 Chinese parents raising children with autism participated in this study. All completed the CSI, along with the social inhibition subscale of the Interpersonal Problems Inventory and the Couple Satisfaction Index. Factorial validity was assessed using CFA to determine how well the bifactor three-factor model fits the data. Various structural models were compared using model fit indices. Convergent and discriminant validity were examined by exploring correlations with the social inhibition subscale and the Couple Satisfaction Index. Invariance testing of the CSI was conducted across multiple groups based on gender, age, and education using CFA. The reliability of the CSI was evaluated using McDonald’s omega coefficients. (3) Results: The bifactor model emerged as the best-fitting model for the data, suggesting that the total score of the CSI adequately represents overall psychiatric symptoms. The CSI exhibited significant correlations with the social inhibition subscale (r = 0.41, p &lt; 0.01) and smaller correlation coefficients with the Couple Satisfaction Index (r = -0.16, p &lt; 0.05), indicating both convergent and discriminant validity. Invariant tests supported scalar invariance levels based on gender and age but only partial invariance for education. The Chinese version of the CSI demonstrated high consistency, with McDonald's omega coefficients ranging between 0.86 and 0.95. (4) Conclusions: The bifactor model of the Chinese version of the CSI is validated, making it a suitable tool for measuring depression, anxiety, and somatization symptoms among parents of children with autism spectrum disorders. Further research on other Chinese populations is encouraged.

This article systematically studied the A-optimal designs of a high-order mixture central polynomial model, which is an advancement of the research results for the A-optimal design of the most recent third-order mixture central polynomial model and a more accurate response surface model. This article is based on the simplex center design, obtaining measurement values at various design points, and verifying them through the A-optimal equivalence theorem. We also compare the A-efficiency of designs through examples, which can be applied to the A-optimal precise design of the fourth-order mixture model.

The prevalence of diabetes mellitus (DM) continues to rise globally, posing significant health challenges and burdens. This metabolic disorder, characterized by elevated blood glucose levels, contributes to various complications including cardiovascular diseases, kidney failure, and stroke. While conventional diabetic drugs exist, they often come with adverse side effects, necessitating the exploration of safer and more cost-effective alternatives, particularly from natural sources like medicinal plants. This study investigates the potential of Neocarya macrophylla (Nm) Ethyl acetate leaf fraction in managing DM. Utilizing a high-fat diet/streptozotocin-induced diabetic rat model, the study explores several key aspects including effective dose determination, biological activity, impact on body mass index (BMI), and complete blood count. Statistical analysis was conducted using GraphPad Prism version 9.1. The determination of the minimum effective dose reveals that 120mg/kg of Ethyl acetate fraction of Nm reduced the blood glucose by 28.9% after 4 hours. In addition, ethyl acetate fraction (120 mg/kg) possessed the most hypoglycemic activity compared to the other fractions of Nm. The Ethyl acetate fraction of Nm at 120mg/kg significantly reduced fasting blood glucose levels compared to the diabetic control(p=0.001) and slightly decreased BMI. Furthermore, the fraction demonstrated significant improvement in the parameters of some of the blood count indices such as red blood cells (p<0.001), total white cells (p<0.01) and platelet (p<0.001) compared to the diabetic control. These findings underscore the potential of Nm as a holistic therapeutic option for managing DM and its haematological complications. In conclusion, this study sheds light on the hypoglycemic potential of Nm Ethyl acetate leaf fraction, offering valuable insights into its effectiveness, safety, and broader physiological impacts. Further research into the mechanisms underlying its therapeutic effects is warranted to fully harness its therapeutic potential in diabetes management.

High-precision displacement sensing has been widely used across from both scientific researches and industrial applications. The recent interests in developing micro-opto-electro-mechanical systems (MOEMS) have given rise to an excellent platform for miniaturized displacement sensors. Advancement in this field during past years is now yielding integrated high-precision sensors which show great potential in applications ranging from photoacoustic spectroscopy to high-precision positioning and automation. In this review, we briefly summarize different techniques for high-precision displacement sensing based on MOEMS, and discuss the challenges for future improvement.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

Multifunctional landscapes are complex systems that integrate biophysical, cultural-historical and socio-economic components into unique territorial structures and regional ensembles. Facing increasing pressures generated by urbanization, climate change and overexploitation of natural resources, assessing the sustainability of these landscapes has become an urgent priority. The present research is based on the development and parametrization of a new tool for evaluating the sustainability of multifunctional landscapes that aims to measure the level of biocultural resilience of a landscape, integrating biological, cultural and socio-economic indicators in a single analytical framework. This index, called the biocultural resilience index (BRI), provides a holistic perspective on the dynamics of landscapes, allowing the identification of vulnerability areas and the development of conservation and sustainable management strategies. The evaluation of the of multifunctional landscapes sustainability requires a comprehensive approach that has to integrate both biological aspects, such as biodiversity and ecosystem health, as well as identity and cultural aspects, such as cultural value and the relationship of the local communities with the environment. In this context, this study highlights the fact that the development of appropriate tools and methods for assessing and monitoring the sustainability of multifunctional landscapes becomes essential for their sustainable management and for protecting the benefits they offer to society. Our findings show that the biocultural resilience index (BRI) can be used in a variety of contexts and fields, including spatial planning, biodiversity conservation, sustainable rural development and ecotourism. In the meanwhile, this index offers a robust and flexible analytical framework, adaptable to the needs and particularities of different regions and communities.

A high-gain broadband circularly polarized crossed dipole antenna is designed. This antenna utilizes two pairs of cross dipoles and a pair of phase delay lines to form circularly polarized radiation. Open-circuit stubs are loaded on the four arms of these two pairs of cross dipoles to introduce new circularly polarized resonating frequency. A rectangular ring patch is introduced directly below the cross dipoles to form the third circularly polarized resonating frequency, thereby broadening the axial ratio bandwidth of the antenna. In addition, metal posts are loaded at the four right angles of the rectangular ring patch to increase the antenna gain. Measurement results show that the antenna achieves a 3dB axial ratio bandwidth of 29.2% (1.9 GHz-2.55 GHz) and maintains a gain of 7.5 dB within the passband, exhibiting good circularly polarized radiation performance.