Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

The domestic ducks (Anas platyrhynchos domesticus) are resistant to most of the highly pathogenic avian influenza virus (HPAIV) infections. In this study, we characterized the lung proteome and phosphoproteome of ducks infected with HPAI H5N1 virus (A/duck/India/02CA10/2011/Agartala) at 12 hr, 48 hr and 5 days post infection condition. Total 2082 proteins were differentially expressed and 320 phosphorylation sites mapping to 199 phosphopeptides corresponding to 129 proteins were identified. Functional annotation of proteome data analysis reveals activation of RIG-I-like receptor and Jak-STAT signaling pathways, that lead to induction of interferon stimulated genes (ISGs) expression. The pathway analysis of phosphoproteome datasets also confirms the activation of RIG I, Jak-STAT signaling, NF-kappa B signaling and MAPK signaling pathways in the lung tissues. The induction of ISGs proteins (STAT1, STAT3, STAT5B, STAT6, IFIT5 and PKR) establishes protective antiviral immune response in duck lung tissue. Further, the protein-protein interaction network analysis identified proteins like AKT1, STAT3, JAK2, RAC1, STAT1, PTPN11, RPS27A, NFKB1 and MAPK1 as main hub proteins that might play important roles in disease progression in ducks. Together, functional annotation of proteome and phosphoproteome datasets reveals the molecular basis of the disease progression and disease resistance mechanism in ducks infected with HPAI H5N1 virus.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Soccer is the leading cause of all sports-related ocular injuries in Europe and Israel and leads to blindness at a disproportionately high rate, especially among children (Thompson et al., 2019). With soccer being the most popular sport in the world, it is surprising the only solution to ocular injuries are sports glasses which can cause direct damage to the eye and impair peripheral vision by 15%, calling for an alternative (Smith & Jones, 2020). This work, based on an imported facial model, focuses on both the qualitative and quantitative aspects of building a personalized, low-cost (through optimizing material needed), superior apparatus to conventional sports glasses. The quantitative side examines a modified and model-validated (through a SRS of thirty unique extrapolated points) multivariate linear regression equation, based on horizontal and vertical rotation angles (n=60) trained with residual and computer simulation data, that can accurately extrapolate and quantify ocular impact from all horizontal and vertical rotation angles and a modified Hertzian Contact Stress Equation to determine the thickness of the apparatus using the elasticity modulus, impact force, and geometrical facial and soccer-ball features. The qualitative side examines where firstly, ocular impact is most prevalent, and secondly, where most impact is seen from rotating the ball horizontally and vertically through analysis of Pearson’s Correlation Coefficient at the supraorbital, medial canthus, infraorbital, and lateral canthus regions from both regression equations as well as a cost-benefit analysis for comparison with conventional sports glasses. The findings discovered in this work lay the groundwork for future research to build a customized low-cost ocular injury prevention device which can simultaneously ensure complete ocular safety while enhancing athletic performance for over 250,000,000 players (Johnson & Garcia, 2022).

The study aimed to investigate the impact of incorporating deep learning strategies in mathematics instruction on students' problem-solving abilities, critical thinking skills, academic achievement, and mathematical skills development. The study population consisted of 280 students, with a sample size of 162 participants. Employing a purely quantitative approach, data collection utilized questionnaires and achievement tests as instruments. Data analysis involved simple linear regression, descriptive analysis, and Pearson correlation. The results of the study revealed that there was no significant enhancement observed in students' problem-solving abilities and critical thinking skills when deep learning strategies were incorporated into mathematics instruction. Additionally, students' attitudes towards deep learning activities in mathematics showed no effect on their academic achievement. Furthermore, students' engagement levels in deep learning activities did not impact their development of mathematical skills. Lastly, the frequency of deep learning activities in the mathematics classroom did not show a significant relationship with students' academic performance. These findings suggest that the implementation of deep learning strategies in mathematics instruction did not yield notable improvements in the specified areas based on the study outcomes.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

In this paper, we focus on the impact of financial liberalization on stability of emerging stock market. We identify crises in a group of Latin American (Argentina, Brazil and Chile) and Asian countries (Philippines, Korea, Taiwan and Thailand) during 1975–2005. This paper aims to apply the methodology of CMAX method. Our results indicate that liberalization triggers more unstable stock market in the short run and generate several crises. Still, liberalization seems to generate more stable financial markets in the long run. Financial liberalization does not increase the frequency of crises in emerging countries and at long-term, crises are less several.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

This paper introduces an innovative Particle Swarm Optimization (PSO) Algorithm in-corporating Sobol and Halton Random number samplings. It evaluates the enhanced PSO's performance against conventional PSO employing Monte Carlo Random Number Samplings. The comparison involves assessing the algorithms across nine benchmark problems and the renowned Travelling Salesman Problem (TSP). The re-sults reveal consistent enhancements achieved by the enhanced PSO utilizing Sob-ol/Halton samplings across the benchmark problems. Particularly noteworthy are the substantial improvements demonstrated by the enhanced PSO in solving the Travel-ling Salesman Problem. These findings underscore the efficacy of employing Sobol and Halton random number generation methods in enhancing algorithm efficiency.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Coffee production around the world is under threat due to climate variability and change, and drought stress will increase in many coffee regions, nutrient management practices could enhance the adaptation capacity of coffee production. Considering that coffee is a sensitive crop to boron (B) deficiency, this research investigated how B nutrition improves resistance to drought stress in coffee under controlled conditions as well how with interaction with calcium (Ca+2) influences productivity, seed compositions, and soil fertility during a production cycle of 5 year. Under controlled conditions for seven months, coffee plants were submitted to water stress with and without B nutrition. In the field, coffee plantation was submitted to two B rates (0,6 and 1,1 kg. ha-1-year-1) with fixed calcium (Ca+2) rate and, a control without Ca+2 and B. After 9 months of growth and seven months of water deficit, under controlled conditions, the application of B significantly (p<0,05) reduced the negative effect of water stress on coffee growth. Under field conditions, after a production cycle of 5 years, the application of 0,6 kg B and 77 kg CaO. ha-1. year-1 yielded 14% more than the control without B and Ca+2. An increase of the B rate to 1.1 kg.ha-1.year-1 with the same Ca+2 rate increased the productivity significantly (p<0,05) by 37% compared to the control. B application also improved significantly (p<0,05) the B content in the soil at 0-30 cm. The B treatments influenced the biochemical composition of the green coffee beans, with a significant (p<0,05) inverse correlation between the B content of the green coffee beans with caffeine, and unsaturated fatty acids (UFAs) mainly, oleic, linoleic, and linolenic acids which are considered negative descriptors of the coffee quality.

Significant advances in Penning trap measurements of atomic masses and mass ratios of the proton, deuteron, triton, helion, and alpha-particle have occurred in the last five years. These include a measurement of the mass of the deuteron against 12C with 8.5 x 10-12 fractional uncertainty; resolution of vibrational levels of H2+ as mass and the application of a simultaneous measurement technique to the H2+/D+ cyclotron frequency ratio, yielding a deuteron-proton mass ratio at 5 x 10-12; new measurements of HD+/3He+, HD+/T+ and T+/3He+ leading to a tritium beta-decay Q-value with an uncertainty of 22 meV, and atomic masses of the helion and triton at 13 x 10-12; and a new measurement of the mass of the alpha-particle against 12C at 12 x 10-12. Some of these results are in strong disagreement with previous literature values. Their impact in determining a precise proton/electron mass ratio and electron atomic mass from spectroscopy of the HD+ molecular ion is also discussed.

Light-colored and transparent polyimide (PI) films with good high-temperature dimensional stability are highly desired for advanced optoelectronic applications. However, in practice, the simultaneous achievement of good optical and thermal properties in one PI film is usually difficult due to the inter-conflicting molecular design for the polymers. In the present work, a series of PI-SiO2 nanocomposite films (ABTFCPI) were developed based on the PI matrix derived from hydrogenated pyromellitic anhydride (HPMDA) and an aromatic diamine containing benzanilide and trifluoromethyl substituents in the structure, 2,2'-bis(trifluoromethyl)-4,4'-bis[4-(4-aminobenzamide)]biphenyl (ABTFMB). The inorganic SiO2 fillers were incorporated into the nanocomposite films with the form of colloidal nanoparticles dispersed in the good solvent of N,N-dimethylacetamide (DMAc) for the PI matrix. The derived ABTFCPI nanocomposite films showed good film-forming ability, flexible and tough nature, good optical transparency, and good thermal properties with the loading amounts of SiO2 up to 30 wt% in the system. The ABTFCPI-30 film with the SiO2 content of 30 wt% in the film showed the optical transmittance of 79.6% at the wavelength of 400 nm (T400) with a thickness of 25 μm, the yellow index (b*) of 2.15, and the 5% weight loss temperatures (T5%) of 491 oC, which are all comparable to those the pristine ABTFCPI-0 matrix without filler (T400=81.8%; b*=1.77; T5%=492 oC). Meanwhile, the ABTFCPI-30 film exhibited obviously enhanced high-temperature dimensional stability with the linear coefficients of thermal expansion (CTE) of 25.4×10-6/K in the temperature range of 50 to 250 oC, which is much lower than that of the AMTFCPI-0 film (CTE=32.7×10-6/K).

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

Traditional methods for discovery and development of new drugs can be a very time-consuming and expensive process because it includes several stages such as compound identification, pre-clinical and clinical trials before the drug is approved by the US Food and Drug Administration (FDA). Therefore, drug repurposing, namely using currently FDA-approved drugs as therapeutics for other diseases than what they are originally prescribed for, is emerging to be a faster and more cost-effective alternative to current drug discovery methods. In this paper, we have described a three-step in silico protocol for analyzing transcriptomics data using online databases and bioinformatics tools for identifying potentially repurposable drugs. The efficacy of this protocol was evaluated by comparing its predictions with the findings of two case studies of recently reported repurposed drugs: HIV treating drug Zidovudine for the treatment of Dry Age-Related Macular Degeneration and the antidepressant Imipramine for Small-Cell Lung Carcinoma. The proposed protocol successfully identified the published findings, thus demonstrating the efficacy of this method. In addition, it also yielded several novel predictions that have not yet been published, including the finding that Imipramine could potentially treat Severe Acute Respiratory Syndrome (SARS), a disease that currently does not have any treatment or vaccine. Since this in-silico protocol is simple to use and does not require advanced computer skills, we believe any motivated participant with access to these databases and tools would be able to apply it to large datasets to identify other potentially repurposable drugs in the future.

Diamond powders with inclusions of europium atoms were synthesized at high pressure (7.7 GPa) and temperature (1800oC) from a mixture of pentaerythritol, C(CH2OH)4, and pyrolyzate of diphthalocyanine (C64H32N16Eu) served as a special precursor. In prepared diamonds by X-ray fluorescence spectroscopy, we have found the concentration of Eu atoms of 51±5 ppm that is by two orders of magnitude greater than that in known natural and synthetic diamonds. X-ray diffraction, SEM, X-ray exited optical luminescence, Raman and IR spectroscopy have confirmed the formation of diamond monocrystals of high quality with em-bedded Eu atoms and a nitrogen content of ~500 ppm. Numerical simulation has allowed us de-termine the energy cost of 5.8 eV needed for the incorporation of a single Eu atom with adjacent vacancy into growing diamond crystal (528 carbons).

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

This study presents a comprehensive investigation of the formation, composition, and behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3, 13Cr, T24 and P91) at a uniform temperature of 650 °C. The research combines CALPHAD (CALculation of PHAse Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, including scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD calculations were used to determine the thermodynamically stable phases for each steel type at 650 °C. The results showed different phase compositions, highlighting the importance of steel composition in the formation of oxide layers. Each steel grade exhibited different kinetics, with 16Mo3 steel showing the highest oxidation rate, followed by 13Cr, T24 and P91. This variability highlights the role of steel composition, particularly chromium content, in determining oxidation behaviour. These results have significant implications for temporary overheating in industrial applications and contribute to a deeper understanding of oxidation processes in steels.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

The poor oxidation resistance of refractory high-entropy alloys (RHEAs) is a major obstacle for their use in high-temperature engineering applications. Anti-oxidation coating technology is an effective method for improving the oxidation resistance. In this paper, the Si-20Cr-20Fe coating was prepared on MoNbTaTiW RHEA by a fused slurry method. The microstructural evolution and compositions of the silicide coating under high-temperature oxidation environment were studied. The results show that the silicide coating could effectively prevent the oxidation of the MoNbTaTiW RHEA. The initial silicide coating had a double-layer structure; a high silicon-content layer mainly composed of MSi2 as the outer layer and a low silicon-content layer mainly contained M5Si3 as the inner layer. Under high-temperature oxidation conditions, the silicon element diffused from the silicide coating to the RHEA substrate while the oxidation of the coating occurred. After oxidation, the coating was composed of an outer oxide layer and an inner silicide layer. The silicide layer moved toward the inside of the substrate, led to the increase of its thickness. Compared with the initial silicified layer, its structure did not change significantly. The structure and compositions of the oxide layer on the outer surface strongly depended on the oxidation temperature. This paper provides a strategy for protecting RHEAs from oxidation at high-temperature environments.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

Nowadays, with the development of laser weapons, the primary power supply of laser weapons puts forward more and more high demand for its performance. The pulsed power supply based on conventional homopolar inductor alternator (HIA) cannot meet the requirements any more. In order to improve the power density and efficiency, this paper proposes applying the high-temperature superconducting (HTS) HIA with slotless stator core to this power supply. In this paper, the design considerations of it are presented, and the comparisons between the two power supplies are discussed. The calculation results show that the power supply based on HTS machine has much larger power density than the conventional HIA, and the efficiency is also larger than the conventional HIA. This can improve the performance of laser weapons dramatically.

A typical white-light light-emitting diode (LED) can achieve a sunlight-like spectral profile in the visible spectrum by means of using an optical filter, with an inverted transmission profile to the white LED, fabricated using a deposition coating process. The unfiltered white LED generates white light by mixing light emitted by a blue LED (450 nm) with emission from the yellow phosphorescence excited by the blue light and differs significantly from the characteristics of the full-spectrum natural light. In this study, the spectral characteristics of the filtered LED light can be improved to reach a general color rendering index value (Ra) of 95.6 at the D65.

A fast calculation method for the full parallax high-resolution hologram is proposed based on the elemental light field image (EI) rendering. A 3D object located near the holographic plane is firstly rendered as multiple EIs with a pinhole array. Each EI is interpolated and multiplied by a divergent sphere wave and interfered with a reference wave to form a hogel. Parallel acceleration is used to calculate the high-resolution hologram because calculation of each hogel is independent. A high-resolution hologram with the resolution of 20,0000×20,0000 pixels is calculated only within 8 minutes. Full parallax high-resolution 3D displays are realized by optical reconstructions.

Liquid and gas are distinct in their extent of dynamic atomic correlations; in gas atoms are almost uncorrelated whereas they are strongly correlated in liquid. This distinction applies also to electronic systems. Fermi liquids are actually gas-like, whereas strongly correlated electrons are liquid-like. Doped Mott insulators share characteristics with supercooled liquids. Such distinctions have important implications on superconductivity. We discuss the evolution of dynamic atomic correlations in liquid with temperature, and a possible effect of dynamic correlations on the high-temperature superconductivity in the cuprates.

Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

Binderless zeolite macrostructures in the form of ZK-4 microspheres were prepared using anion exchange resin beads as shape directing macrotemplates. The particles were synthesized under hydrothermal conditions at different temperatures and treatment times. The influence of the different synthesis parameters was investigated by X-ray diffraction, scanning electron microscopy, fluorescence X, nitrogen adsorption measurements and ²⁹Si solid NMR. Fully crystalline spheres similar in size and shape to the original resin beads were obtained by a hydrothermal treatment at the highest temperatures (150 - 180 °C) for a short treatment time of 24 h. The synthesized microspheres showed to be promising in the molecular decontamination of Volatile Organic Compounds (VOCs).

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

This manuscript describes the construction and validation of high resolution daily gridded (0.05° × 0.05°) rainfall and maximum and minimum temperature data for Bangladesh : the Enhancing National Climate Services for Bangladesh Meteorological Department (ENACTS-BMD) dataset. The dataset was generated by merging data from weather stations, satellite products (for rainfall) and reanalysis (for temperature). ENACTS-BMD is the first high-resolution gridded surface meteorological dataset developed specifically for studies of surface climate processes in Bangladesh. Its record begins in January 1981 and is updated in real-time monthly and outputs have daily, decadal and monthly time resolution. The Climate Data Tools (CDT), developed by the International Research Institute for Climate and Society (IRI), Columbia University, is used to generate the dataset. This data processing includes the collection of weather and gridded data, quality control of stations data, downscaling of the reanalysis for temperature, bias correction of both satellite rainfall and downscaled reanalysis of temperature, and the combination of station and bias-corrected gridded data. The ENACTS-BMD dataset is available as an open-access product at BMD’s official website, allowing the enhancement of the provision of services, overcoming the challenges of data quality, availability, and access, promoting at the same time the engagement and use by stakeholders.

Rice production, owing to its high-water requirement for cultivation, is very vulnerable to the threat of changing climate, particularly prolonged drought and high temperature. Such threats heighten the need for abiotic stress-resilient rice varieties with better yield potential. This review examines the physiological and molecular mechanisms of rice varieties to cope with stress conditions of drought (DS), high temperature (HTS) and their combination (DS-HTS). It appraises research studies in rice about its various phenotypic traits, genetic loci and response mechanisms to stress conditions to help craft new breeding strategies for rice varieties with improved resilience to abiotic stresses. This review consolidates available information on promising rice cultivars with desirable traits as well as advocates synergistic and complementary approaches in molecular and systems biology to develop new rice breeds that favorably respond to climate-induced abiotic stresses. The development of new breeding and cultivation strategies for climate-resilient rice varieties is a challenging task. It requires a comprehensive understanding of the various morphological, biochemical, physiological, and molecular components governing yield under drought and high temperature, but possible by implementing cohesive approaches involving molecular and systems biology approaches in genomics and molecular breeding, including genetic engineering.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

(1) Background: The aim of the research was to present and emphasize the importance of magnetic resonance imaging (MRI) in diagnosing Achilles tendon (AT) ruptures by presenting case reports. (2) Materials and Methods: The sample of respondents included 7 patients (4 males and 3 females, 2 athletes and 5 non-athletes), aged 25 to 58 years, with AT injuries, who were examined and treated at the Institute for Treatment and Rehabilitation "Niška Banja", Niš, Serbia. Ankle examinations with MRI were conducted using the Esaote O-scan 0.3 T machine. The examinations were performed without the application of a paramagnetic contrast agent and without the use of anesthesia. Results: The MRI method's sensitivity and overall diagnostic accuracy were excellent, with 100% true positives. In our study, the method accurately detected the presence, location, and severity of AT injuries in all cases. MRI is an important and reliable method for detecting AT injuries, classifying them, monitoring the course of recovery, and assessing the effects of therapy. Conclusions: An unrecognized or delayed diagnosis of an AT injury can lead to chronic changes. Timely diagnosis (clinical examination, ultrasonography, magnetic resonance imaging) and appropriate treatment (conservative or operative) enable patients to return to normal activities, including sports. Unfortunately, the use of MRI is limited by restricted access and the cost of the examination.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

An analysis of the processes of plastic deformation and acoustic relaxation in a high-entropy alloy Al0.5CoCrCuFeNi was carried out. The following have been established: dominant dislocation defects; types of barriers that prevent the movement of dislocations; mechanisms of thermally activated movement of various elements of dislocation lines through barriers at room and low temperatures. Based on modern dislocation theory, quantitative estimates have been obtained for the most important characteristics of dislocations and their interaction with barriers.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electrical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus, construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases, either conventional or unconventional, and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of commercial polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-NIPAAm polymer and graphene oxide (GO) blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of PVDF to NIPAAm. PVDF-g-NIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-NIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and mechanical properties of the membrane without affecting the temperature response, thus extending the service life of the membrane.

Ultra-short laser pulses (1030 nm/230 fs) were used to laser ablate surface of crystalline sapphire. Laser ablated patterns were annealed at high temperature 1500∘C. Surface reconstruction took place removing ablation debris field at the edges of ablated pits in oxygen flow. Partial reconstruction of ripples was also observed.

By making periodic thru-holes in a suspended film, the phonon system can be modified. Motivated by the BCS theory, the technique -- so-called phonon engineering -- was applied to a metallic niobium sheet. It was found that its electrical resistance dropped to zero at 175 K, and the zero-resistance state persisted up to 290 K in the subsequent warming process. Despite the initial motivation, neither these high transition temperatures nor the phase transition with thermal hysteresis can be accounted for by the BCS theory. Therefore, we abandon the BCS theory. Instead, it turns out that the metallic holey sheet is partly oxidized to form a niobium-oxygen square lattice, which has points of resemblance to a copper-oxygen plane, the fundamental component of cuprate high-T_c superconductors. Therefore, the pairing mechanism underlying this study should be related to that of cuprate high-T_c superconductors, which we may not yet understand. In addition to the electrical results of zero resistance, the holey sheet exhibited a decrease in magnetization upon cooling, i.e., the Meissner effect. Moreover, the remnant magnetization was clearly detected at 300 K, which can only be attributed to persistent currents flowing in a superconducting sample. Thus, this study meets the established criteria for a conclusive demonstration of true superconductivity. Finally, the superconducting transition with the unambiguous thermal hysteresis is discussed. According to Halperin, Lubensky, and Ma, or HLM for short, any superconducting transition must always be first order with thermal hysteresis because of the intrinsic fluctuating magnetic field. The HLM theory is very compatible with the highly oriented system harboring two-dimensional superconductivity.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

Over the years, leaked fluids from the aircraft caused severe deterioration of the airfield pavement. The combined effect of hot exhaust from the auxiliary power unit of military aircraft and spilt aviation oils caused rapid pavement spalling. If the disintegrated concreted pieces caused by spalling is sucked into the jet engine, it may cause catastrophic damage to the aircraft engine or physical injury to maintenance crews. This study investigates the effectiveness of incorporating hybrid fibres into ordinary concrete to improve the residual mechanical and thermal properties to prevent spalling damage of pavement. Three fibre reinforced concrete samples made with micro steel fibre and polyvinyl alcohol fibre with a fibre content of zero, 0.3%, 0.5% and 0.7% by volume fraction. These samples were exposed to recurring high temperature and aviation oils. Tests were conducted to measure the effects of repeated exposure on the concrete's mechanical, thermal and chemical characteristics. The results showed that polyvinyl alcohol fibre reinforced concrete suffered a significant loss of thermal properties and residual mechanical strength than the micro steel fibre reinforced concrete. However, hybrid fibre reinforced concrete performed better in retaining higher residual properties, and no spalling of concrete was observed.

Prolonged ethanol (EtOH) consumption is associated with male infertility with a decreased spermatogenesis rate as one cause. Defective maturation and development of sperm during their storage in the cauda epididymis and transit in the seminal vesicle can be another cause, possibly occurring before the drastic spermatogenesis disruption. Herein, we demonstrated that the cauda epididymis and seminal vesicle of rats, orally fed with EtOH under a regimen that spermatogenesis was still ongoing, showed histological damage, including lesion and decreased height of the epithelial cells, and increased collagen fibers in the muscle layer, which implicated fibrosis. Lipid peroxidation (shown by malondialdehyde (MDA) levels) was observed, indicating that reactive oxygen species (ROS) was produced along with acetaldehyde during EtOH metabolism by CYP2E1. MDA, acetaldehyde and other lipid peroxidation products could further damage cellular components of the cauda epididymis and seminal vesicle and this was supported by increased apoptosis (shown by TUNEL assay and caspase 9/caspase 3 expression) in these two tissues of EtOH-treated rats. Consequently, functionality of the cauda epididymis and seminal vesicle in EtOH-treated rats was impaired, as demonstrated by decreases in 1H NMR-analyzed metabolites (e.g., carnitine, fructose), which were important for sperm development, metabolism and survival in their lumen.

MCrAlX (M: Ni or Co or both, X: minor elements) coatings have been widely used to protect hot components in gas turbines against oxidation and hot corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behaviour is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y+Ru and Ce, respectively, were deposited on Inconel-792 substrate by HVOF. The samples were subjected to isothermal oxidation test in laboratory air at 9000, 1000, 1100 ºC and cyclic oxidation test between 100 ºC and 1100 ºC with 1 hour dwell time at 1100 ºC. It was observed that the coating with Ce shows a much higher oxidation rate than the coating with Y+Ru under both isothermal and cyclic oxidation tests. Besides, β-depletion due to interdiffusion between coating and substrate was significantly lower with Ru addition. Simulations results using both a moving phase boundary model and an established oxidation-diffusion model show that Ru stabilize β grains which reduces β-depletion of coating due to substrate interdiffusion. This paper presents a comprehensive study of the influence of Ce and Ru on oxidation behaviour including investigation of the microstructure evolution influenced by oxidation time at coating surface and coating-substrate interface combining experiment and simulation results.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

A quantum Otto engine with a single ion harmonic oscillator as its working substance is studied for an adiabatic operation at high and low temperature limits. Using the universal optimization method, the heat engine is effectively optimized and found to yield better working conditions in some ranges of temperature ratios. Accordingly, the figure of merit, ψ, is found to be greater than unity in the range: 0<β2β1≤0.12; showing that the heat engine performs better in the optimized condition than in the maximum power working condition. ψ is determined to be less than one in the range 0.12≤β2β1≤0.35 under the same temperature limit ; depicting that the maximum power working condition is preferred to the optimized working condition. On the other hand, in the low temperature limit, the figure of merit, ψ, is found to be greater than unity in the range 3.7<ω1ω2≤18; revealing that optimized working condition is better than the maximum power working condition for the heat engine. In the same temperature limit, ψ is found to be less than one in the range 0≤ω1ω2≤3.7; showing that maximum power working condition is preferred to the optimized one. For the model of heat engine studied, in some ranges of temperature ratio, it is found to work better in the optimized condition, whereas in the other ranges it performs better under the maximum power working condition. So, it is possible to switch the engine between the two conditions depending on one’s need.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

Alloy 800H stands as one of the few code qualified materials for fabricating in core and out of core components operating in high temperature reactors (HTRs). Welding is a common practice for assembling these components, however, the election of a suitable filler material is essential to enhance the high-temperature creep resistance of Alloy 800H weldments in high temperature applications. In this study, Inconel 625 and Haynes 230 filler material were used to weld the Alloy 800H plates employing the Gas Tungsten Arc Welding (GTAW) technique. The high temperature tensile, creep rupture property, microstructural stability and evolution of the weldments after high temperature exposure were investigated and compared with Alloy 800H. The results showed that the both weldments exhibited enhanced tensile and creep behavior at 760 oC. The creep rupture time of the weldments with Inconel 625 filler and Haynes 230 filler materials was about two and three time longer than that of Alloy 800H base metal when tested at 80 MPa and 760 oC, respectively. Carbides (MC and M23C6) were commonly observed in the microstructure of both the weld and base metals in the two weldments after high temperature creep tests. However, the Inconel 625 filler weldment displayed detrimental δ and Laves phase in the fusion zone and these precipitates could be potential sites for initiating cracks following prolonged high temperature exposure. The study showed that the weldment with Haynes 230 exhibited better phase stability and creep rupture property than the one with Inconel 625 filler material, suggesting its potential as a candidate filler material for Alloy 800H for further investigation. The finding also emphasizes the critical consideration of microstructural evolutions and phase stability in evaluating high temperature materials and their weldments in high temperature reactor applications.

Surgical techniques are gaining attention for treating physical diseases in aquaculture and aquarium fish. Sturgeon is a suitable species for surgical experiments due to its industrial significance. Maintaining homeostasis is crucial during surgical procedures, and the liver plays a major role in immune regulation. High temperature is suggested to improve physiological activity and wound healing. This study investigated differences in hepatectomy sturgeons' tolerance and histopathological responses of internal organs. Moreover, this study investigated the effects of high temperature on wound healing and hematopoietic recovery in fish undergoing surgical procedures. The liver condition was found to play a pivotal role in the analysis, and cortisol levels were affected by anesthesia. The results showed that high temperature facilitated hematopoietic recovery and wound healing, but excessive induction of physiological activity caused damage. Managing high temperatures and liver condition induced a remarkable improvement in wound healing. However, anesthesia itself can be a significant stressor for fish, and wound healing requires a greater amount of energy. Further research is needed to understand the stress factors caused by surgical procedures and anesthesia and to promote animal welfare in fisheries products.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

Franklinite-Zincochromite-Gahnite solid solutions have been prepared by ceramic or coprecipitation method and its pigmenting capacity as cool ceramic pigments in different glazes (double and single firing frits and porcelain frit) was studied. XRD, UV-Vis-NIR diffuse reflectance, CIEL*a*b* colour analysis, bandgap measurement and the photocatalytic activity over the Orange II azoic dye were carried out for the characterization of samples. Following criteria of high red colouring capacity and high NIR reflectance at minimum Cr amount, Zn(Fe1.8Cr0.2), Zn(Al1.5Cr0.5) and Zn(Al1.3Cr0.5Fe0.2)O4 turn out to be the optimal compositions for an intense reddish cool pigment. All powders show a direct semiconductor behaviour with bandgap around 2 eV, falling in the visible range (620 nm), and according to literature, the associated photocatalytic activity over Orange II with visible light irradiation is moderate in all cases, but the Franklinite-Zincochromite Zn(Fe1.8Cr0.2) stands out.

We study the influence of high-order twisting phases on polarization states and optical angular momentum of a vector light field with locally linear polarization and a hybrid state of polarization (SoP). The initial SoP of a twisted vector optical field (TVOF) modulated by the high-order twisting phase possesses various symmetric distributions. The propagating properties of a high-order TVOF with locally linear polarization and hybrid SoP are explored, including the intensity compression, expansion, and conversion between the linear and circular polarization components. In particular, orbital angular momentum (OAM) appears in a high-order TVOF during propagation where no OAM exists in the initial field. The variation of OAM distribution in cross-section becomes more frequent with the increase of the twisting phase order. In addition, a non-symmetric OAM distribution appears in an anisotropic TVOF, leading to the rotation of the beam around the propagation axis during propagation. These results provide a new approach for optical field manipulation in a high-order TVOF.

Stray light is a critical aspect for high performance optical instruments. When stray light control by design is insufficient to reach the performance requirement, correction by post-processing must be considered. This situation is encountered for example in the case of the Earth observation in-strument 3MI, whose stray light properties are complex due to the presence of many ghosts dis-tributed on the detector array. We implement an iterative correction method and discuss its con-vergence properties. Spatial and field binning can be employed to reduce the computation time but at the cost of a decreased performance. Interpolation of the stray light properties is required to achieve high performance correction. For that, two methods are proposed and tested. The first interpolate the stray light in the field domain while the second applies a scaling operation based on a local symmetry assumption. Ultimately, the scaling method is selected and a stray light reduction by a factor of 58 is obtained at 2σ (129 at 1σ) for an extended scene illumination.

The dairy industry relies heavily on milk pasteurization to ensure the safety and quality of milk products. Pasteurization is a process that involves heating milk to a specific temperature for a set period of time to kill harmful bacteria and other pathogens while preserving its nutritional value. recent years, newer techniques such as High Temperature Short Time (HTST) pasteurization have gained popularity due to their efficiency and effectiveness. HTST pasteurization involves rapidly heating milk to a high temperature for a short duration of time, followed by rapid cooling. This process helps to minimize the loss of flavor and nutrients in milk while ensuring its safety. However, there is still a need in the market for a compact and remotely controlled process plant for milk pasteurization. The proposed work aims to address this need by designing a process plant that is not only compact but also remotely controlled, allowing for efficient and convenient operation. can control the process plant remotely, allowing for flexibility and convenience in monitoring and managing the pasteurization process from anywhere with an internet connection

The SiBOC precursor ceramics were fabricated by polymer-derived method SiBOC precursors with different B/Si molar ratios were synthesized by controlling monomer content. The effects of different process conditions on SiBOC ceramics and the oxidation resistance of SiBOC ceramics at a high temperature (1400 ℃) were studied. The SiBOC precursor’s bonds of Si-O-C, Si-O-Si, and Si-O-B were detected by FTIR. The precursor is converted to a rigid ceramic material that has an 85.3 wt % ceramic yield of SiBOC ceramics with B/Si=0.4 by TG-DSC. The results of SEM analysis show that the SiBOC ceramics surface bulges and folds increase with the increase of boric acid content. With the increase of pyrolysis temperature and pyrolysis time, the size and number of pores on the surface of SiBOC ceramics also increase. Static oxidation tests show that SiBOC ceramics with B/Si=0.4 have better oxidation resistance under other conditions being the same.

The present study investigated the effect of different ambient temperature and relative humidity (RH) but equal temperature-humidity index (THI) on laying performance, egg quality, heterophil to lymphocyte ratio (H/L ratio), corticosterone (CORT) concentration in blood, yolk and albumen, and plasma biochemical parameters in laying hens. One hundred and twenty commercial hens (Hy-Line Brown) aged 60 weeks were allocated into 2 environmental chambers. Laying hens were subjected to either one of two thermal treatments, i.e., 26ºC and 70% RH (LH75) and 30ºC and 30% RH (HL75) for 28 days. Both thermal treatments had equal THI being 75. Neither LH75 nor HL75 affected (P > 0.05) laying performance including egg production, egg weight, egg mass, feed intake, and feed conversion ratio. Plasma biochemical parameters such as total cholesterol, high-density lipoprotein cholesterol, triglyceride, calcium, magnesium, and phosphorus was not altered (P > 0.05) by thermal treatments. As to the stress indicators, both environment regimes failed (P > 0.05) to affect blood H/L ratio and CORT levels in plasma, yolk and albumen although albumen CORT levels were elevated (P < 0.05) in LH75 vs. HL75 at days 3, 7, and 28. In conclusion, our study suggests that laying hens performed and responded equally when they were exposed to equal THI environment conditioned from either 26ºC and 70% RH or 30ºC and 30% RH. The results of this study will be served as a scientific basis for management decisions and handling under thermally challenging conditions.

1) Background: Climate change may subject forests to climate conditions to which they are not adapted. Elevated temperatures reduce net photosynthesis by increasing respiration rates and increasingly long droughts dramatically increase morbidity. CO₂ enrichment enhances productivity, but it is not clear to what extent CO₂ enrichment can offset the negative effects of elevated temperatures and longer droughts. 2) Methods: We used a mechanistic landscape model to conduct controlled simulation experiments manipulating CO₂ concentration, temperature, drought length and soil water capacity. 3) Results: We found that elevated CO₂ stimulates productivity such that it dwarfs the negative effect caused by elevated temperature. Energy reserves were not as strongly mitigated by elevated CO₂, and mortality of less competitive cohorts increased. Drought length had a surprisingly small effect on productivity measures, but had a marked negative effect on mortality risk. 4) Conclusions: Elevated CO₂ compensated for the negative effect of longer droughts in terms of productivity measures, but not survival measures.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

Ion beam-assisted deposition (IBAD) has been proposed as a promising texturing technology that uses film epitaxy method to obtain biaxial texture on a non-textured metal or compound substrate. Magnesium oxide (MgO) is the most well explored texturing material. In order to obtain the optimal biaxial texture, the actual thickness of the IBAD-MgO film must be controlled within 12 nm. Due to the bombardment of ion beams, IBAD-MgO has large lattice deformation, poor texture and many defects in the films. In this work, an additional homogeneous epitaxy MgO (epi-MgO) layer has been deposited on the IBAD-MgO layer by electron-beam evaporation. The biaxial texture can be optimized by the deposition of additional epi-MgO layer. The effects of growth temperature, film thickness, deposition rate and oxygen flux on the texture and morphology of the epi-MgO film were systematically studied. After the research of epi-MgO process, the best full width at half maximum (FWHM) values were 2.2 for the out-of-plane texture and 4.8° for the in-plane texture, respectively. Subsequently, the LaMnO3 cap layer and YBa2Cu3O7-x (YBCO) functional layer was deposited on the epi-MgO layer to test the quality of MgO layer. Finally, the critical current density of YBCO films is 6MA/cm2 (77K, 500nm, self-field), indicating that this research provides a high-quality MgO substrate for the YBCO layer.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

Concrete has become the most common construction material showing among other advantages good behaviour when subjected to high temperatures. Nevertheless, concrete is usually reinforced with elements of other materials such as steel in the form of rebars or fibres. Thus, the behaviour under high temperatures of these other materials can be critical for structural elements. In addition, concrete spalling occurs when concrete is subjected to high temperature due to internal pressures. Micro polypropylene fibres (PP) have shown to be effective for reducing such spalling although this type of fibres barely improve any of the mechanical properties of the element. Hence, a combination of PP with steel rebars or fibres can be effective for the structural design of elements exposed to high temperatures. New polyolefin fibres (PF) have become an alternative to steel fibres. PF meet the requirements of the standards to consider the contributions of the fibres in the structural design. However, there is a lack of evidence about the behaviour of PF and elements made of polyolefin fibre reinforced concrete (PFRC) subjected to high temperatures. Given that these polymer fibres would be melt above 250 °C, the behaviour in the intermediate temperatures was assessed in this study. Uni-axial tests on individual fibres and three-point bending tests of PFRC specimens were performed. The results have shown that the residual load-bearing capacity of the material is gradually lost up to 200 °C, though the PFRC showed structural performance up to 185°C.

Ferulic acid esters have been suggested as a group of natural chemicals with sunscreen function. The study aimed to utilize an environment-friendly enzymatic method to produce octyl ferulate by esterification of ferulic acid with octanol. The Box-Behnken design with response surface methodology (RSM) was adopted to evaluate the effects of synthesis variables, including reaction temperature (70–90 °C), enzyme amount (1000–2000 PLU) and stir speed (50–150 rpm), on the molar conversion of octyl ferulate. According to the joint test, both the reaction temperature and enzyme amount had great impacts on the molar conversion. RSM-developed second-order polynomial equation further showed great ability on data-fitting. Based on ridge max analysis, the optimum parameters for the biocatalyzed reaction were: 72 h reaction time, 92.2 °C reaction temperature, 1831 PLU enzyme amount and 92.4 rpm stir speed, respectively. Finally, the molar conversion of octyl ferulate under optimum condition was verified to be 93.2 ± 1.5%. In conclusion, high yield of octyl ferulate synthesized by commercial immobilized lipase under elevated temperature conditions has been suggested, which our findings could broaden the utilization of the lipase and provide a biocatalytic approach, instead of the chemical method, for ferulic acid ester synthesis.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.