We discuss the electrodeposition of two-dimensional (2D) Pt-nanostructures on HOPG achieved under constant applied potential versus a Pt counter electrode (Eappl = ca. - 2.2 V vs RHE). The deposition conditions are discussed in terms of the electrochemical behavior of the electrodeposition precursor (H2PtCl6). We performed cyclic voltammetry (CV) of the electrochemical Pt deposit on HOPG and on Pt substrates to study the relevant phenomena that affect the morphology of Pt deposition. Under conditions where the Pt deposition occurs and H2 evolution is occurring at the diffusion-limited rate (- 0.3 V vs RHE), Pt forms larger structures on the surface of HOPG, and the electrodeposition of Pt is not limited by diffusion. This indicates the need for large overpotentials to direct the 2D growth of Pt. Investigation of the possible effect of Cl- showed that Cl- deposits on the surface of Pt at low overpotentials, but strips from the surface at potentials more positive than the electrodeposition potential. The CV of Pt on HOPG is a strong function of the nature of the surface. We propose that during immersion of HOPG in the electrodeposition solution (3 mM H2PtCl6, 0.5 M NaCl, pH 2.3) Pt islands are formed spontaneously, and these islands drive the growth of the 2D nanostructures.

The diamagnetic levitation technique can be applied to non-destructive testing for identifying cracks and defects in magnetic materials. Pyrolytic graphite is a material that can be leveraged in micromachines due to its no-power diamagnetic levitation on a permanent magnet (PM) array. However, the damping force applied to pyrolytic graphite prevents it from maintaining con-tinuous motion along the PM array. This paper investigates the in-plane motion and damping characteristics of pyrolytic graphite sheets on the PM array. The centroid of pyrolytic graphite will maintain a stable levitation when positioned on the intersecting point of the PM array. Fur-thermore, the in-plane motion of two different pyrolytic graphite sizes - PG10 (10×10×0.5mm3) and PG20 (20×20×0.5mm3) - has revealed that the in-plane forces applied to them are approximately 61.4μN and 28.2μN, respectively. The smaller sheet has a shorter oscillation time while oscillating before it stabilizes. The damping ratio of the oscillation was between 0.1-0.2. The in-plane force and the stable time of pyrolytic graphite are related to its size ratio in comparison with the PM. This relationship is believed to promote stability, as the force acting on the graphite sheet will be distributed over a larger area when the sheet size increases. During the fixed-axis rotation process, the study found that the friction coefficient and friction force decreased as the rotational speed decreased. The diamagnetic levitation of pyrolytic diamagnetic levitation is also unable to maintain long-term axial rotation. Finally, friction force was tested using PG10 during fixed-axis rotation above a circular PM array. The results showed that the order of the friction coefficient is 10-3, and the friction force is about 0.8μN, decreasing with graphite rotation speed. We hope this technique will be used in crack detection, magnetic detection and other micromachine.

Graphite nanoplatelets (GNPs) were produced from flake graphite that had been immersed in isopropyl alcohol solution (70%) and converted to powder form in an ultrasonic bath (5 h, room temperature). Scanning and transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy identified 120-nm-thick GNP crystallites and 0.5–21 µm plates with different areas and shapes. Extensive exfoliation was observed by transmission electron microscopy with abundant multilayer and some monolayer GNPs. X-ray diffractometry confirmed 43 GNP layers along the c-axis. Raman spectroscopy indicated well-defined GNPs with few defects and no oxide content. Rietveld analysis indicated a GNP crystal lattice with stacks of parallel two-dimensional graphene layers and tightly bound hybridized carbon atoms stacked in a translational …ABAB… sequence in hexagonal rings.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Porous graphite was prepared without the use of template by rapidly heating the carbonization products from mixtures of anthracene, flourene, and pyrene with a CO₂ laser. Rapid CO₂ laser heating at a rate of 1.8 × 10 ⁶ °C/s vaporizes out the fluorene-pyrene derived pitch while annealing the anthracene coke. The resulting structure is that of graphite with 100 nm spherical pores. The graphitizablity of the porous material is the same as pure anthracene coke. Transmission electron microscopy revealed that the interface between graphitic layers and the pore walls are unimpeded. Traditional furnace annealing does not result in the porous structure as the heating rates are too slow to vaporize out the pitch, thereby illustrating the advantage of fast thermal processing. The resultant porous graphite was prelithiated and used as an anode in lithium ion capacitors. The porous graphite when lithiated had a specific capacity of 200 mAh/g at 100 mA/g. The assembled lithium ion capacitor demonstrated an energy density as high as 75 Wh/kg when cycled between 2.2 V to 4.2 V.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

Recently published structural analysis and galvanomagnetic studies of a large number of different bulk and mesoscopic graphite samples of high quality and purity reveal that the common picture assuming graphite samples as a semimetal with a homogeneous carrier density of conduction electrons is misleading. These new studies indicate that the main electrical conduction path occurs within 2D interfaces embedded in semiconducting Bernal and/or rhombohedral stacking regions. This new knowledge incites us to revise experimentally and theoretically the diamagnetism of graphite samples. We found that the $c$-axis susceptibility of highly pure oriented graphite samples is not really constant but can vary several tens of percent for bulk samples with thickness $t \gtrsim 30~\mu$m, whereas by a much larger factor for samples with smaller thickness. The observed decrease of the susceptibility with sample thickness resembles qualitatively the one reported for the electrical conductivity and indicates that the main part of the $c-$axis diamagnetic signal is not intrinsic of the ideal graphite structure but it is due to the highly conducting 2D interfaces. The interpretation of the main diamagnetic signal of graphite agrees with the reported description of its galvanomagnetic properties and provides a hint to understand some magnetic peculiarities of thin graphite samples.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The ongoing challenge to ensure a sustainable and affordable energy supply forces industrial companies to implement appropriate measures. These measures typically lead to an increased system complexity, which has to be addressed during operation. Whereas existing approaches from the field of supervisory and optimal control appear to be capable of mastering this issue, these are still not adopted in industry. Therefore, this work presents a procedure model for the systematic development of application-oriented operating strategies for industrial energy supply systems. The procedure model combines research approaches from the fields of sequencing control and approximate MPC to extract rule-based operating strategies. By splitting the procedure model into five phases, expert knowledge can be integrated in a target-oriented manner. Subsequently to the description, the procedure model is exemplary applied to the example of an industrial heating supply system. Throughout an optimization study, the developed operating strategy is compared to a MPC strategy as well as a baseline strategy. Whereas the conventional MPC approach is the upper bound with regard to optimality, the developed operating strategy is able to generate comparable results. Compared to the baseline strategy, a relative reduction in operating expenses of 5.4 % to 37.0 % are achieved in this specific use case.

Chlamydia trachomatis (Ct) infections are the most common sexually-transmitted infection (STI). Despite effective antibiotics for Ct, undetected infections or delayed treatment can lead to infertility, ectopic pregnancies, and chronic pelvic pain. Besides humans, chlamydia poses similar health challenges in animals such as C. suis (Cs) in pigs. Based on the similarities between humans and pigs as well as their chlamydia species, we use pigs as a large biomedical animal model for chlamydia research. In this study, we use the pig model to develop a vaccine candidate against Ct. The vaccine candidate consists of TriAdj-adjuvanted chlamydial protease-like activity factor (CPAF) protein. We tested two weekly administration options – twice intranasal (IN) followed by twice intramuscular (IM), or twice IM followed by twice IN. We assessed the humoral immune response not only in serum by CPAF-specific IgG including antibody avidity determination but also in cervical and rectal swabs by CPAF-specific IgG and IgA ELISAs. The systemic T-cell response was analyzed upon in vitro CPAF-restimulation via IFN-γ and IL-17 ELISpots as well as intracellular cytokine staining flow cytometry. Our data demonstrate that while the IN/IM vaccination mainly led to non-significant systemic immune responses, the vaccine candidate is highly immunogenic if administered IM/IN. This vaccination strategy induced high serum anti-CPAF IgG levels with strong avidity as well as high IgA and IgG levels in vaginal and rectal swabs and in uterine horn flushes. In addition, this vaccination strategy prompted a pronounced cellular immune response: Besides inducing IL-17 production, the vaccine candidate induced a strong IFN-γ response by CD4 T cells. In the IM/IN vaccinated pigs, these cells also significantly downregulated their CCR7 expression – a sign for differentiation into peripheral tissue homing effector/ memory cells. Conclusively, this study demonstrates strong immunogenicity of the IM/IN administered TriAdj-adjuvanted Ct CPAF vaccine candidate. Future studies will test vaccine efficacy of this promising Ct vaccine candidate. In addition, this project demonstrates suitability of the Cs pre-exposed outbred pig model for Ct vaccine development. Thereby, we aim to open the bottleneck of large animal models to facilitate the progression of Ct vaccine candidates into clinical trials.

The domestic ducks (Anas platyrhynchos domesticus) are resistant to most of the highly pathogenic avian influenza virus (HPAIV) infections. In this study, we characterized the lung proteome and phosphoproteome of ducks infected with HPAI H5N1 virus (A/duck/India/02CA10/2011/Agartala) at 12 hr, 48 hr and 5 days post infection condition. Total 2082 proteins were differentially expressed and 320 phosphorylation sites mapping to 199 phosphopeptides corresponding to 129 proteins were identified. Functional annotation of proteome data analysis reveals activation of RIG-I-like receptor and Jak-STAT signaling pathways, that lead to induction of interferon stimulated genes (ISGs) expression. The pathway analysis of phosphoproteome datasets also confirms the activation of RIG I, Jak-STAT signaling, NF-kappa B signaling and MAPK signaling pathways in the lung tissues. The induction of ISGs proteins (STAT1, STAT3, STAT5B, STAT6, IFIT5 and PKR) establishes protective antiviral immune response in duck lung tissue. Further, the protein-protein interaction network analysis identified proteins like AKT1, STAT3, JAK2, RAC1, STAT1, PTPN11, RPS27A, NFKB1 and MAPK1 as main hub proteins that might play important roles in disease progression in ducks. Together, functional annotation of proteome and phosphoproteome datasets reveals the molecular basis of the disease progression and disease resistance mechanism in ducks infected with HPAI H5N1 virus.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

Graphene oxide was synthesized by a one-step environmentally friendly mechanochemistry process directly from graphite and characterized by Raman, FT-IR and UV/vis spectroscopies, Atomic Force Microscopy, X-ray Diffraction, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy and Thermogravimetric Analysis. Spectroscopic analysis shows that the functional groups and oxygen content of the synthesized material are comparable with those of graphene oxide synthesized by other previously reported methods (Hummers). Thermogravimetric analysis reveals thermal stability up to 400 °C.

Spectral characteristics of CDOM in water column are a key parameter for bio-optical modeling. Knowledge of CDOM optical properties and spatial discrepancy based on the relationship between water quality and spectral parameters in Yinma River watershed with in situ data collected highly-polluted waters are exhibited in this study. Seasonal field data sets collected over a period of 2 months in 2015 in Yinma River Watershed. Based on the comprehensive index method, the riverine waters showed serious contamination, especially the COD, Fe, Mn, Hg and DO were out of range contamination warning. Dissolved organic carbon (DOC) and total suspended matter (TSM) with prominent non-homogenizing were significantly high in the riverine waters, but chlorophyll-a (Chl-a) was opposite. Ternary phase diagram showed that non-algal paritcles absorption played an important role in total non-water light absorption (>50%) in most sampling locations, and mean contribution of CDOM were 13% and 22% in summer and autumn respectively. Analysis of ratio of absorption at 250-365 nm (E_250:365) and spectral slope (S_275-295) indicated that CDOM had higher aromaticity and molecular weight in autumn than in summer, is consistent with the results of water quality and relative contribution. Redundancy analysis (RDA) indicated that the environmental variables OSM had a strong correlation with CDOM absorption, followed by heavy metal, e.g., Mn, Hg and Cr⁶⁺. However, for the specific UV absorbance (SUVA₂₅₄), the seasonal values showed opposite results compared with the reported literature. The potential reasons were the more UDOM (uncolored Dissolved Organic Matter) from human source (wastewater effluent) existed in waters. Terrigenous inputs simultaneously are in relation to the a_CDOM(440)-DOC relationship with the correlation coefficient was 0.90 in summer (2-tailed, p<0.01), and 0.58 in autumn (2-tailed, p<0.05). Spatial distribution of CDOM parameters exhibited that the downstream regions focused on dry land have high CDOM molecular weight and aromatic hydrocarbon. Partial sampling locations around the cities or countries generally showed abnormal values due to terrigenous inputs. As a bio-optical model parameter, spectral characteristic of CDOM is helpful in adjusting the derived algorithms in highly-polluted environments. The study on organic carbon and pollutants in highly-polluted waters had an important contribution to global carbon balance estimation and water environment protection.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

In a dynamic production processes, mechanical degradation poses a significant challenge, impacting product quality and process efficiency. This paper explores a novel approach for monitoring degradation in the context of viscose fiber production, a highly dynamic manufacturing process. Using causal discovery techniques, our method allows domain experts to incorporate background knowledge into the creation of causal graphs. Further, it enhances the interpretability and increases the ability to identify potential problems via changes in causal relations over time. The case study employs a comprehensive analysis of the viscose fiber production process within a prominent textile industry, emphasizing the advantages of causal discovery for monitoring degradation. The results are compared with state-of-the-art methods, which are not considered to be interpretable, specifically LSTM-based autoencoders, showcasing the alignment and validation of our approach. This paper provides valuable information on degradation monitoring strategies, demonstrating the efficacy of causal discovery in dynamic manufacturing environments. The findings contribute to the evolving landscape of process optimization and quality control.

Heating films were prepared by using poly(methyl methacrylate) and polybutadiene composites containing graphite. The heating film was prepared by casting the as-made polymer composite on PET film. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film was analyzed while applying DC voltage. The electrical conductivity and the heating temperature of the heating films depended on the size, the structure, the content and the dispersion characteristics of the graphite in the composite. The electrical resistance of the heating film was controlled to adjust the heating temperature of the film. The relationship between the physical/chemical structure and the heating characteristics of the composite film was studied by measuring the heating temperature as functions of film thickness and resistance by using an infrared thermal imaging camera. The lower the film resistance, the higher the heating temperature of the film. The surface temperature was uniform throughout the film.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

Over the past decade, there has been a remarkable acceleration in the evolution of smart cities and intelligent spaces, driven by breakthroughs in technologies such as the Internet of Things (IoT), edge-fog-cloud computing, and machine learning (ML)/Artificial Intelligence (AI). As society begins to harness the full potential of these smart environments, the horizon brightens with the promise of an immersive, interconnected 3D world. The forthcoming paradigm shift in how we live, work, and interact owes much to groundbreaking innovations in augmented reality (AR), virtual reality (VR), extended reality (XR), Blockchain, and Digital Twins (DT). However, realizing the expansive digital vista in our daily lives is challenging. Current limitations include an incomplete integration of pivotal techniques, daunting bandwidth requirements, and the critical need for near-instantaneous data transmission, all impeding the digital VR Metaverse from fully manifesting as envisioned by its proponents. This paper seeks to delve deeply into the intricacies of the immersive, interconnected 3D realm, particularly in applications demanding high levels of intelligence. Specifically, this paper introduces Microverse, a task-oriented, edge-scale, pragmatic solution for smart cities. Unlike an all-encompassing Metaverses, each Microverse instance serves a specific task as a manageable digital twin of an individual network slice. Each Microverse enables on-site/near-site data processing, information fusion, and real-time decision-making within the edge-fog-cloud computing framework. The Microverse concept is verified using smart public safety surveillance (SPSS) for smart communities as a case study, demonstrating its feasibility in practical smart city applications. The aim is to stimulate discussions and inspire fresh ideas in our community, guiding us as we navigate the evolving digital landscape of smart cities to embrace the potential of the Metaverse.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

In this study, graphite, the most stable form of carbon, was examined for its hexagonal crystalline structure with specific dimensions (ao=2.46 Ǻ; co=6.70 Ǻ). Its framework comprises parallel carbon atom planes forming regular hexagons (side length 1.415 Ǻ) and 120° angles between adjacent atoms. Two structural variations exist: hexagonal symmetry (1-2-1-2-1-2 planes) and rhomboidal symmetry (1-2-3-1-2-3 planes). The research aimed to produce high-density graphite utilizing carbonaceous raw materials. Graphite-based materials often exhibit high porosity, necessitating additional treatments. The study successfully obtained mesophase tar pitch (yield: 45%), a pivotal raw material, and high-density graphite. The resulting graphite underwent characterization for physical properties (apparent and real density, porosity and compression strength), demonstrating conformity with existing literature data.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

Mathematical literacy is a very hot issue in the development of mathematics learning, apart from mathematical literacy, another interesting thing is the entrepreneurial spirit that must be given from an early age, especially for vocational students. This research was conducted at SMK Rosma Karawang in the Department of Computer and Network Engineering, West Java Province with the XI grade students. The teaching materials developed by applying the principles of the development model developed with the ADDIE model consist of analysis, design, development, implementation and evaluation. This research and development model is considered suitable for developing teaching tools and materials which is used for the purposes of the learning process. Based on the results of data analysis and processing that have been carried out in this study, the development of teaching materials using the ADDIE model has met the appropriate and valid criteria by media, language and media expert valuators. Another result of developing this teaching material besides meeting the eligibility criteria is that the teaching materials developed are able to increase mathematical literacy and instill entrepreneurial spirit for students.

Discrete distribution estimation is a fundamental statistical tool, which is widely used to perform data analysis tasks in various applications involving sensitive personal information. Due to privacy concerns, individuals may not always provide their raw information, which leads to unpredictable biases in the final results of estimated distribution. Local Differential Privacy (LDP) is an advanced technique for privacy protection of discrete distribution estimation. Currently, typical LDP mechanisms provide same protection for all items in the domain, which imposes unnecessary perturbation on less sensitive items and thus degrades the utility of final results. Although, several recent works try to alleviate this problem, the utility can be further improved. In this paper, we propose a novel notion called Item-Oriented Personalized LDP (IPLDP), which independently perturbs different items with different privacy budgets to achieve personalized privacy protection. Furthermore, to satisfy IPLDP, we propose the Item-Oriented Personalized Randomized Response (IPRR) based on the observation that the sensitivity of data shows an inverse relationship with the population size of respective individuals. Theoretical analysis and experimental results demonstrate that our method can provide fine-grained privacy protection and improve data utility simultaneously.

The notion of oriented set is the basic elementary concept of the theory of changeable sets. The main motivation for the introduction of changeable sets was the sixth Hilbert problem, that is, the problem of mathematically rigorous formulation of the fundamentals of theoretical physics. In the present paper the necessary and sufficient condition of the existence of one-point time on an oriented set is established. From the intuitive point of view, one-point time is the time associated with the evolution of a system consisting of only one object (for example, from one material point). Namely, it is proven that the one-point time exists on the oriented set if and only if this oriented set is a quasi-chain. Also, using the obtained result, the problem of describing all possible images of linearly ordered sets is solved. This problem naturally arises in the theory of ordered sets.

Constitutive models for plastic deformation of metals are typically based on flow rules determining the transition from elastic to plastic response of a material as function of the applied mechanical load. These flow rules are commonly formulated as a yield function, based on the equivalent stress and the yield strength of the material, and its derivatives. In this work, a novel mathematical formulation is developed that allows the efficient use of machine learning algorithms describing the elastic-plastic deformation of a solid under arbitrary mechanical loads and that can replace the standard yield functions with more flexible algorithms. By exploiting basic physical principles of elastic-plastic deformation, the dimensionality of the problem is reduced without loss of generality. The data-oriented approach inherently offers a great flexibility to handle different kinds of material anisotropy without the need for explicitly calculating a large number of model parameters. The applicability of this formulation in finite element analysis is demonstrated, and the results are compared to formulations based on Hill-like anisotropic plasticity as reference model. In future applications, the machine learning algorithm can be trained by hybrid experimental and numerical data, as for example obtained from fundamental micromechanical simulations based on crystal plasticity models. In this way, data-oriented constitutive modeling will also provide a new way to homogenize numerical results in a scale-bridging approach.

Addressing the urgent sustainability challenges in the wine industry, this study explores the efficacy of sustainability-oriented innovations (SOIs) and smart farming technologies (SFTs) across wine value chains in Cyprus and Italy. Employing KPIs for a rigorous assessment, the research delves into the environmental, economic, and social impacts of these technologies. In Cyprus (SIP7), the integration of digital labelling and smart farming solutions led to a substantial reduction in pesticide usage by up to 75% and enhanced the perceived quality of wine by an average of 8%. Italy's SIP10 witnessed a 33.4% decrease in greenhouse gas emissions, with an additional benefit of a 5.3% improvement in intrinsic product quality. Notably, SIP10 also introduced a carbon credit system, potentially generating an average annual revenue of €4,140 per farm. These findings highlight the transformative potential of SOIs and SFTs in promoting sustainable practices within the wine industry, demonstrating significant advancements in reducing environmental impact, improving product quality, and enhancing economic viability. The study underscores the critical role of innovative technologies in achieving sustainability goals and provides a compelling case for wider adoption within the agricultural sector.

Today with enhancement in technology, sciences, there is also an increase in global heating rate. There is an urgent need of any alternate efficient source to reduce the wastage of energy and to utilize it efficiently. The advanced preparation of Expanded graphite ,lauric acid, stearic acid as shape stabilized phase change material deals with different energy harvesting applications. The main reason behind the need for synthesis of this matrix is to prepare a material that can be used in low temperature energy storage applications. Mixture of lauric acid , stearic acid impregnated in expanded graphite through vacuum impregnation followed by Vacuum Drying and Microwave acid treatment serves as novel shape stabilized phase change material of its type. The microwave acid treatment was done in order to increase the removal of moisture from the sample thus initiating proper bonding of its constituents. The mixture was produced in 1:1:1 ratio where all expanded graphite, lauric acid , stearic acid has one proportions of each other. The product obtained after microwave acid treatment was subjected to SEM, DSC analysis

We fabricate paper-supported semiconducting devices by rubbing a layered molybdenum disulfide (MoS₂) crystal onto a piece of paper, similarly to the action of drawing/writing with a pencil on paper. We show that the abrasion between the MoS₂ crystal and the paper substrate efficiently exfoliates the crystals, breaking the weak van der Waals interlayer bonds and leading to the deposition of a film of interconnected MoS₂ platelets. Employing this simple method, that can be easily extended to other 2D materials, we fabricate MoS₂-on-paper broadband photodectectors with spectral sensitivity from the ultraviolet (UV) to the near-infrared (NIR). We also used these paper-based photodetectors to acquire pictures of objects by mounting the photodetectors in a homebuilt single-pixel camera setup.

This paper presents a cascade predictive control structure based on the field-oriented control (FOC) in the dq rotor reference frame for the synchronous reluctance machine (SynRM). The constant d-axis current control strategy was used and thus, the electromagnetic torque was directly controlled by the q-axis current. Because the model of the two axes currents from the inner loop is a coupled non-linear multivariable one, to non-interaction linear control the two currents, their decoupling was achieved through feedforward components. Following the decoupling, two independent monovariable linear systems resulted for the two currents dynamics that were controlled using model predictive control (MPC) algorithms, considering their ability to automatically handle the state bounds. The most important bounds for SynRM are the limits imposed on currents and voltages, which in the dq plane correspond to a circular limit. To avoid computational effort, linear limitations were adopted through polygonal approximations, resulting in rectangular regions in the dq plane. For the outer loop that controls the angular speed with a constrained MPC algorithm, as plant was considered the q-axis current closed loop dynamics and the torque linear equation. To evaluate the performances of the proposed cascade predictive control structure, a simulation study using MPC controllers versus PI ones was conducted.

Optimization using Genetic Algorithms (GA) is a well-known strategy in several scientific disciplines. The crossover is an essential operator of the Genetic Algorithm. It has been an active area of research to develop sustainable forms for this operand. In this work, a new crossover operand is proposed. This operand depends on giving an elicited description for the chromosome with a new structure for alleles of the parents. It is suggested that each allele has two attitudes, one attitude differs contrastingly with the other, and both of them complement the allele. Thus, in case of one attitude is good, the other should be bad. This is suitable for many systems which contain admired parameters and unadmired parameters. The proposed crossover would improve the desired attitudes and damp the undesired attitudes. The proposed crossover can be achieved in two stages: the first stage is a mating method for both attitudes in one parent to improving one attitude at the expense of the other. The second stage comes after the first improvement stage for mating between different parents. Hence, two concurrent steps for improvement would be applied. Simulation experiments for the system shows improvement in the fitness function. The proposed crossover could be helpful in different fields, especially to optimize routing algorithms and network protocols, an application that has been tested as a case study in this work.

As a system becomes more complex, at first, its description and analysis becomes more complicated. However, a further increase in the system’s complexity often makes this analysis simpler. A classical example is Central Limit Theorem: when we have a few independent sources of uncertainty, the resulting uncertainty is very difficult to describe, but as the number of such sources increases, the resulting distribution get close to an easy-to-analyze normal one – and indeed, normal distributions are ubiquitous. We show that such limit theorems make analysis of complex systems easier – i.e., lead to blessing of dimensionality phenomenon – for all the aspects of these systems: the corresponding transformation, the system’s uncertainty, and the desired result of the system’s analysis.

Henry Vidal first introduced the concept of using strips, grids, and sheets for reinforcing soil masses. Since then, a large variety of materials such as steel bars, tire shreds, polypropylene, polyester, glass fibers, coir, jute fibers etc. have been widely added to the soil mass randomly or in a regular, oriented manner. In this investigation, a new concept of multi-oriented plastic reinforcement (hexa-pods), is discussed. A systematic and comprehensive laboratory tests were conducted on unreinforced and reinforced soil samples. Laboratory tests such as direct shear teat and California bearing ratio (CBR) test were analyzed on soil samples consisting of only soil samples, soil sample with random inclusion of hexapods and soil samples with layered inclusion of hexapods. From the results obtained through direct shear test it could be observed that cohesion value of both the soil sample has increased and the angle of internal friction has been decreased after reinforcing it with inclusions in both randomly and layered conditions. CBR test indicates that for same amount of compactive effort, both random and layered inclusions of hexapods show improvement in strength and stiffness. Random inclusions of hexapods give better resistance to penetration as compared to layered inclusions. The hexa-pods also changed the brittle behavior of unreinforced sand samples to ductile ones.

Autonomous and cooperative vehicle systems represent a key priority in the automotive realm. Networked driving simulation can be utilized as a safe, cost-effective experimental replica of real traffic environments in order to support and accelerate the development of such systems. In networked driving simulation, different independent systems collaborate to achieve a common task: multi-driver traffic scenario simulation. Yet distinct system complexity levels are necessary to fulfill the requirements of various application scenarios, such as development of vehicle systems, analysis of driving behavior, and training of drivers. With myriad alternatives of available systems and components, developers of networked driving simulation are typically confronted with high design complexity. There are no systematic approaches to date for the design of networked driving simulation in accordance with the specific requirements of the concerned application scenarios. This paper presents a novel design method for networked driving simulation. The method consists mainly of a procedure model that is accompanied by a configuration software. The procedure model includes the necessary phases for the systematic design of application-oriented platforms for networked driving simulation. The configuration software embeds supportive decision-making processes that enable developers to apply the design method and easily create different system models. The design method was validated by generating system models and developing platforms of networked driving simulation for three different application scenarios.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

Non-impregnated small pore graphite (NSPG) with the compact microstructure for using in molten salt reactors (MSR) was prepared by the novel process, and the pore diameter of the obtained graphite was reduced to ~800 nm. The irradiation evaluation of the prepared graphite was carried out by 7 MeV Xe26+ ion irradiation and the microstructural changes of the graphite were investigated with IG-110 as a comparison. The graphitization degree of NSPG was higher than that of IG-110, though it was not subjected to an impregnation process. Under low-dose ion irradiation (

Graphite carbon nitride (g-C3N4) supported PtNi alloy nanoparticles (NPs) were fabricated via a facile and simple impregnation and chemical reduction method and explored their catalytic performance towards hydrogen evolution from ammonia borane (AB). Interestingly, the resultant Pt_0.5Ni₀.5/g-C₃N₄ catalyst affords superior performance, including 100% conversion, 100% H₂ selectivity, yielding the extraordinary initial total turnover frequency (TOF) of 250.8 mol_H2 min^-1 (mol_Pt)^-1 for hydrogen evolution from AB at 10 °C, a relatively low activation energy of 38.09 kJ mol⁻¹, and a remarkable reusability (at least 10 times), which surpass most of the noble metal heterogeneous catalysts. This notably improved activity is attributed to the charge interaction between PtNi NPs and g-C₃N₄ support. Especially, the nitrogen-containing functional groups on g-C₃N₄, serving as the anchoring sites for PtNi NPs, may be beneficial for becoming a uniform distribution and decreasing the particle size for the NPs. Our work not only provides a cost-effective route for constructing high-performance catalysts towards the hydrogen evolution of AB but also prompts the utilization of g-C₃N₄ in energy fields.

The performance of lattice-Boltzmann solver implementations usually depends mainly on memory access patterns. Achieving high performance requires then complex code which handles careful data placement and ordering of memory transactions. In this work, we analyse the performance of an implementation based on a new approach called the data-oriented language, which allows the combining of complex memory access patterns with simple source code. As a use case, we present and provide the source code of a solver for D2Q9 lattice and show its performance on GTX Titan Xp GPU for dense and sparse geometries up to 4096 2 nodes. The obtained results are promising, around 1000 lines of code allowed us to achieve performance in the range of 0.6 to 0.7 of maximum theoretical memory bandwidth (over 2.5 and 5.0 GLUPS for double and single precision, respectively) for meshes of size above 1024 2 nodes, which is close to the current state-of-the-art. However, we also observed relatively high and sometimes difficult to predict overheads, especially for sparse data structures. The additional issue was also a rather long compilation, which extended the time of short simulations, and a lack of access to low-level optimisation mechanisms.

The paper interprets a comparison of two mostly used techniques of a field-oriented control for 6-phase electric drives, with their pros and cons, as well as their differences in construction and behaviour. Both of these approaches have been realized. Frequency and step responses analysis have been demonstrated with a 6-phase permanent magnet synchronous machine. Experimental results have been compared with simulations based on a mathematical model.

Internet-led labour market has become so competitive forcing many organisations from different sectors to embrace e-recruitment. However, realising the value of the e-recruitment from a Requirements Engineering (RE) analysis perspective is challenging. This research is motivated by the results of a failed e-recruitment project conducted in military domain which is used as a case study in this research. After reviewing the various challenges faced in that project through a number of related research domains, this research focuses on two major problems which are the (1) difficulty of scoping, representing, and systematically transforming recruitment problem knowledge towards e-recruitment solution specification; and (2) the difficulty of documenting e-recruitment best practices for reuse purposes in an enterprise recruitment environment. In this paper, a Problem-Oriented Conceptual Model (POCM) with a complementary Ontology for Recruitment Problem Definition (Onto-RPD) is proposed to contextualise the various recruitment problem viewpoints from an enterprise perspective and to elaborate those problem viewpoints towards a comprehensive recruitment problem definition. The POCM and Onto-RPD are developed incrementally using action-research conducted on three real case studies: (1) Secureland Army Enlistment, (2) British Army Regular Enlistment, and (3) UK Undergraduate Universities and Colleges Admissions Service (UCAS). They are later evaluated in a focus group study against a set of criteria. The study showed that the POCM and Onto-RPD provide a strong foundation for representing and understanding the e-recruitment problems from different perspectives.

In industry 4.0 era, video applications such as surveillance visual systems, video conferencing, or video broadcasting have been playing a vital role. In these applications, for manipulating and tracking objects in decoded video, the quality of decoded video should be consistent because it largely affects to the performance of the machine analysis. To cope with this problem, we propose a novel perceptual video coding (PVC) solution in which a full reference quality metric named Video Multimethod Assessment Fusion (VMAF) is employed together with a deep convolutional neural network (CNN) to obtain the consistent quality while still achieving the high compression performance. First of all, to achieve the consistent quality requirement, we propose a CNN model with an expected VMAF as input to adaptively adjust the quantization parameters (QP) for each coding block. Afterwards, to increase the compression performance, a Lagrange coefficient of Rate-Distortion optimization (RDO) mechanism is adaptively computed under Rate-QP and Quality-QP models. Experimental results show that the proposed PVC has achieved two targets simultaneously: the quality of video sequence is kept consistently with an expected quality level and the bit rate saving of the proposed method is higher than traditional video coding standards and relevant benchmark, notably with around 10% bitrate saving in average.

Background: Residents of a large area of North-Eastern Italy were exposed for decades to high concentrations of perfluoroalkyl and polyfluoroalkyl substances (PFAS) via drinking water. Despite the large amount of evidence in adults of a positive association between serum PFAS and metabolic outcomes, studies focusing on children and adolescents are limited. We evaluated the associations between serum PFAS concentrations and lipid profile, blood pressure and body mass index (BMI) in highly exposed adolescents and children. Methods: A cross-sectional analysis was conducted in 6669 adolescents (14-19 years) and 2693 children (8-11 years) enrolled in the health surveillance program of the Veneto Region. Non-fasting blood samples were obtained and analyzed for perfluorooctanoic acid (PFOA) perfluorooctane sulfonate (PFOS), perfluorohexanesulfonic acid (PFHxS), perfluorononanoic acid (PFNA), total cholesterol (TC) high-density lipoprotein cholesterol (HDL-C) and triglycerides. Low-density lipoprotein cholesterol (LDL-C) was calculated. Systolic and diastolic blood pressure (BP) were measured and BMI z-score accounting for age and sex was estimated. The associations between ln-transformed PFAS (and categorized into quartiles) and continuous outcomes were assessed using generalized additive models. Analyses were stratified by gender and adjusted for potential confounders. Results: Among adolescents, significant associations were detected between all investigated PFAS and TC, LDL-C, and to a fewer extent HDL-C. Among children, PFOS and PFNA had significant associations with TC, LDL-C and HDL-C, while PFOA and PFHxS had significant associations with HDL-C only. Increased serum concentrations of PFAS, particularly PFOS, were associated with decreased BMI z-score. No statistically significant associations were observed between PFAS concentrations and BP. Conclusions: Our study supports a consistent association between PFAS concentration and serum lipids, stronger for PFOS and PFNA and with a greater magnitude among children compared to adolescents, and a negative association of PFAS with BMI.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

The ubiquitous deployment of Li-ion batteries (LIBs) in more demanding applications has reinforced the need to understand root-causes of thermal runaway. Herein we perform a forensic simulation of a real-case failure scenario, using localised heating of Li(Ni0.5Mn0.3Co0.2)O2 versus graphite 18650 cylindrical cells. This study determined the localised temperatures that would lead to venting and thermal runaway of these cells, as well as correlating the gases produced as a function of degradation pathway. Catastrophic failure, involving melting (with internal cell temperatures exceeding 1085°C), deformation and ejection of cell componentry, was induced by locally applying 200 °C and 250 °C to a fully charged cell. Conversely, catastrophic failure was not observed when the same temperatures were applied to the cells at lower state of charge (SOC). This work highlights the importance of SOC, chemistry and heat in driving the thermal failure mode of Ni-rich LIB cells, allowing for a better understanding of battery safety and associated design improvements.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

It is a challenging and meaningful task to carry out drone-based livestock monitoring in high-altitude and cold regions. The purpose of AI is to execute automated tasks and to solve practical problems in actual applications by combining the software technology with the hardware carrier to create integrated advanced devices. Only in this way, the maximum value of AI could be realized. In this paper, a real-time tracking system with dynamic target tracking ability is proposed. It is developed based on the tracking-by-detection architecture using YOLOv7 and DeepSORT algorithms for target detection and tracking, respectively. To address the existing problems of the DeepSORT algorithm, the following two optimizations are made: (1) Optical flow is used to compensate the Kalman filter for improvement of the prediction accuracy; (2) A low-confidence trajectory filtering method is adopted to reduce the influence of unreliable detection on target tracking. In addition, an visual servo controller for the UAV is designed to enable the automated tracking task. Finally, the system is tested using the Tibetan yaks living in the Tibetan Plateau as the tracking targets, and the results reveal the real-time multiple tracking ability and the ideal visual servo effect of the proposed system.

Highly macroporous thin films of WO₃ were fabricated on transparent conductive substrates by application of a polymeric organic paste loaded with an amine/tungstate complex. After spin-coating and annealing at 550^oC, the resulting yellow films are found to be comprised of channeled array of clustered nanoparticles. These channels are confirmed by scanning electron microscopy to extend through the entire length of the coating. The high porosity of the material enables the insertion of a co-catalyst into the internal structure of the film. These internally functionalized composites demonstrate good photosensitivity and stability in neutral electrolyte.

Rapid advancements in the fifth generation (5G) communication technology and mobile edge computing (MEC) paradigm lead to the proliferation of unmanned aerial vehicles (UAV) in urban air mobility (UAM) networks, which provide intelligent services for diversified smart city scenarios. Meanwhile, the widely deployed internet of drones (IoD) in smart cities also brings up new concerns on performance, security, and privacy. The centralized framework adopted by conventional UAM networks is not adequate to handle high mobility and dynamicity. Moreover, it is necessary to ensure device authentication, data integrity, and privacy preservation in UAM networks. Thanks to characteristics of decentralization, traceability, and unalterability, Blockchain is recognized as a promising technology to enhance security and privacy for UAM networks. In this paper, we introduce LightMAN, a lightweight microchained fabric for data assurance and resilience-oriented UAM networks. LightMAN is tailored for small-scale permissioned UAV networks, in which a microchain acts as a lightweight distributed ledger for security guarantees. Thus, participants are enabled to authenticate drones and verify the genuineness of data that is sent to/from drones without relying on a third-party agency. In addition, a hybrid on-chain and off-chain storage strategy is adopted that not only improves performance (e.g,.latency and throughput) but also ensures privacy preservation for sensitive information in UAM networks. A proof-of-concept prototype is implemented and tested on a Micro Air Vehicle Link (MAVLink) simulator. The experimental evaluation validates the feasibility and effectiveness of the proposed LightMAN solution.

Oriented object detection is a challenging task in scene text detection and remote sensing image analysis, which has attracted extensive attention in recent years with the development of deep learning. Currently, mainstream oriented object detectors are based on preset anchor boxes. This method increases the computational load of the network and cause a large amount of anchor box redundancy. To solve this problem, we propose anchor-free oriented object detection based on the Gaussian centerness(AOGC), a single-stage anchor-free detection method. Our method uses contextual attention FPN(CAFPN) to obtain the contextual information of the target. Then we design a label assignment method for oriented objects. Finally, we develop a Gaussian kernel-based centerness branch, which can effectively determine the significance of different anchors. AOGC achieves mAP of 74.30% on the DOTA-1.0 datasets and 89.80% on the HRSC2016 datasets, respectively. AOGC exhibits superior performance to other methods in oriented anchor-free object detection methods.

Background: In Transcranial Direct Current Stimulation (tDCS) the injected current gets distributed across the brain areas. The motive is to stimulate the target region-of-interest (ROI), while minimizing the current in non-target ROIs. For this purpose, determining the appropriate current-dose for an individual is difficult. Aim: To introduce Dose-Target-Determination-Index (DTDI) to quantify the focality of tDCS and examine the dose-focality relationship in three different populations. Method: Here, we extended our previous toolbox i-SATA to the MNI reference space. After a tDCS montage is simulated for a current-dose, the i-SATA(MNI) computes the average (over voxels) current density for every region in the brain. DTDI is the ratio of average current density at target ROI to the ROI with maximum value (peak region). Ideally target ROI should be the peak region, so DTDI shall range from 0 to 1. Higher the value, the better the dose. We estimated the variation of DTDI within and across individuals using T1-weighted brain images of 45 males and females distributed equally across three age groups- (a) Young adults (20 ≥ x ˂ 40 years), (b) Mid adults (40 ≥ x ˂ 60 years), and (c) Older adults (60 ≥ x ˂ 80 years). DTDI’s were evaluated for the frontal montage with electrodes at F3 and right supra-orbital for three current doses 1mA, 2mA, and 3mA with the target ROI at left middle frontal gyrus. Result: As the dose is incremented, DTDI may show (a) increase, (b) decrease, and (c) no change across the individuals. The focality decreases with age and the decline is stronger in males. Higher current dose at older age can enhance the focality of stimulation. Conclusion: DTDI provides information on which tDCS current dose will optimize the focality of stimulation. DTDI recommended dose should be prioritised based on the age (> 40 years) and sex (especially males) of an individual. The toolbox i-SATA(MNI) is freely available.

Crosslinking of proteins for their irreversible immobilization on surfaces is a proven and popular method. However, many protocols lead to random orientation and the formation of undefined or even inactive by-products. Most concepts to obtain a more targeted conjugation or immobilization requires the recombinant modification of at least one binding partner, which is often impractical or prohibitively expensive. Here a novel method is presented, which is based on the chemical preactivation of Protein A or G with selected conventional crosslinkers. In a second step, the antibody is added, which is subsequently crosslinked in the Fc part. This leads to an oriented and covalent immobilization of the immunoglobulin with a very high yield. Protocols for Protein A and Protein G with murine and human IgG are presented. This method may be useful for the preparation of columns for affinity chromatography, immunoprecipitation, antibodies conjugated to magnetic particles, permanent and oriented immobilization of antibodies in biosensor systems, microarrays, microtitration plates or any other system, where the loss of antibodies needs to be avoided, and maximum binding capacity is desired. This method is directly applicable even to antibodies in crude cell culture supernatants, raw sera or protein-stabilized antibody preparations without any purification nor enrichment of the IgG. This new method delivered much higher signals as a traditional method and, hence, seems to be preferable in many applications.

Most of the research of mental fatigue evaluation mainly concentrated on some indexes that require sophisticate and large instruments which make the detection of mental fatigue cumbersome, time-consuming, and difficult to apply on a large scale. A quick and sensitive mental fatigue detection index is necessary so that mental workers can be alerted in time and take corresponding countermeasures. But to date, no studies have compared the sensitivity of common objective evaluation indexes. To solve these problems this study recruited 56 human subjects. These subjects were evaluated using six fatigue indexes: the Stanford sleepiness scale, digital span, digital decoding, short-term memory, critical flicker fusion frequency (CFF), and speed perception deviation. The results of fatigue tests before and after mental fatigue were compared, and a one-way analysis of variance (ANOVA) was performed on the speed perception deviation. The result indicated the significance of this index. Considering individual differences, the relative fatigue index (RFI) was proposed to compare the sensitivity of the indexes. The results showed that when the self-rated fatigue grade changed from non-fatigue to mild fatigue, the ranges of RFI values for digital span, digital decoding, short-term memory and CFF were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. Correspondingly, when the self-rated fatigue grade changed from non-fatigue to severe fatigue, the ranges of RFI values for the above indexes were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. These results suggest that the sensitivity of the digital decoding, digital span, short-term memory, and CFF decreased sequentially when the self-evaluated fatigue grade changed from no fatigue to mild or severe fatigue. The RFI individuality of the speed perception deviation is highly variable and is not suitable as an evaluation index. In mental fatigue testing, digital decoding testing can provide faster, more convenient, and more accurate results.

In airborne sensor networks (ASNs), the media access control (MAC) protocol is facing with serious unfairness problem due to the traditional protection mechanism of air-to-air communications among aircrafts. Actually by using the binary exponential back-off algorithm at high traffic loads to minimize collisions among users, the latest successful node can always benefit from this kind of MAC to obtain channel resources. Moreover, when taking the existence of the hidden nodes in ASNs into account, the inaccurate traffic load information will further aggravate the system’s unfairness. In this paper, a neighbor-channel-aware (NCA) protocol is proposed to improve the fairness of MAC protocol in ASNs. In the proposal, the NCA frame is firstly added and exchanged between neighbor nodes periodically, which helps to resolve the inaccurate traffic load information, so as to avoid reducing the probability of successful message transmission. Then a traffic-loading based back-off algorithm is involved to make the neighbor nodes cooperatively adjust the inter-frame space (IFS) interval to further reduce the unfairness. The simulation results show that, the proposed MAC protocol can guarantee the satisfied fairness, simultaneously avoiding heavy network overloads to protect key messages’ successful transmissions in ASNs.

The newly established virus family Phenuiviridae in Bunyavirales harbors viruses infecting three kingdoms of host organisms (animals, plants, and fungi), which is rare in known virus families. Many phenuiviruses are arboviruses and replicate in two distinct hosts (e.g., insects and humans or rice). Multiple phenuiviruses, such as Dabie bandavirus, Rift Valley fever phlebovirus, and Rice stripe tenuivirus, are highly pathogenic to humans, animals, or plants. They impose heavy global burdens on human health, livestock industry, and agriculture and are research hotspots. In recent years the taxonomy of Phenuiviridae has been expanded greatly, and researches on phenuiviruses have made significant progress. With these advances, this review drew a novel panorama regarding the biomedical significance, distribution, morphology, genomics, taxonomy, evolution, replication, transmission, pathogenesis, and control of phenuiviruses, to aid researchers in various fields to recognize this highly adaptive and very important virus family.

Due to the impacts from climate change, the allocation of water resources must urgently be optimized worldwide to ensure that the needs of both water managers and farmers are balanced. In this study, manager-oriented and farmer-oriented assessment models were developed for irrigation water optimization and allocation. The distance from water sources and hydraulic head were the main factors in the manager-oriented assessment model; crop value, water demand of crops, and soil type were additional factors in the farmer-oriented assessment model. The developed assessment models were used to assess irrigation water allocation in five villages in Neimen District. Cadasters at high elevation were discovered to not be suitable for cultivation of crops because of the difficulties in constructing irrigation facilities and the loss of irrigation water during transportation. The result obtained from the manager-oriented assessment system was related to the costs involved in the construction and maintenance of irrigation facilities, which indicated that cadasters located at long distances from water sources and at high elevation are unsuitable for cultivation. By contrast, the result obtained from the farmer-oriented assessment system was related to the profits of farmers and revealed that more cadasters would be suitable for cultivation if suitable crops were chosen.

The rapid evolution of Next Generation Sequencing in clinical settings and the resulting challenge of variants interpretation in the light of constantly updated information, requires robust data management systems and organized approaches to variant reinterpretation. In this paper, we present iVar: a freely available and highly customizable tool provided with a user-friendly web interface. It represents a platform for the unified management of variants identified by different sequencing technologies. iVar accepts, as input, VCF files and text annotation files and elaborates them, optimizing data organization and avoiding redundancies. Updated annotations can be periodically re-uploaded and associated to variants as historicize attributes. Data can be visualized through variant-centered and sample-centered interfaces. A customizable search functionality can be exploited to periodically check if pathogenicity related data of a variant are changed over time. Patient recontacting ensuing from variant reinterpretation is made easier by iVar through the effective identification of all patients present in the database and carrying a specific variant. We tested iVar by uploading 4171 VCF files and 1463 annotation files, obtaining a database of 4166 samples and 22569 unique variants. iVar has proven to be a useful tool with good performances for collecting and managing data from medium-throughput

The economics and safety of reactors can be affected by the diffusion of fission products into graphite. Xenon (Xe) fission products diffusing into the graphite is the most critical neutron absorber and poison that can slow down or stop the chain reaction. The transport parameters for inhibiting the xenon diffusion in graphite are therefore the utmost scientific problem. Self-sintered nanopore-isotropic (~ 40nm) graphite (SSNG) derived from green pitch coke can decrease Xe diffusion into the graphite. In this study, a method for measurement of diffusion coefficients of fission products diffusion in graphite by Rutherford backscattering spectrometry (RBS) was reported. The SSNG substrates were implanted with Xe at a dose of 4.8×1015 ions/cm2 and energy of 7 MeV. The RT-implanted samples were annealed in a vacuum at 650°C for 9 h. The implanted and annealed samples were characterized by RBS. The diffusion coefficient D(Xe,650°C) is 6.49×10-20 m2/s. The results indicate the excellent ability to inhibit Xe diffusion of the SSNG and present significance in designing and evaluating the safety of nuclear reactors.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

Development of carbon nanomaterials for adsorption thus removal of organic pollutants from water is a progressive research subject. In this regard, carbon nanomaterials with bifunctionality towards polar and non-polar or even amphiphilic undesired materials is indeed attractive for further study and implementation. Here, we created carbon buckypaper adsorbents comprising amphiphilic (oxygenated amorphous carbon (a-COx)/graphite (G)) nanofilaments that can dynamically adsorb organic biomolecules (i.e. urease enzyme) and thus purify the wastewaters of relevant industries. Given the dynamic conditions of the test, the adsorbent was highly efficient in adsorption of the enzyme (88%) while permeable to water (2382 L.h-1.m-2), thus holds a great promise for further development and upscaling. A subsequent citric acid functionalization declined selectivity of the membrane to urease, implying the biomolecules adsorb mostly via graphitic domains rather than oxidized, polar amorphous carbon ones. The devised platform i.e. the urease functionalized buckypaper is optimally conductive (13 S.cm-1) and can be further employed as a biosensor. Accordingly, water treatment can be linked to biosensing via a nanostructured membrane.

This review explores the unique structural and functional characteristics of natural products featuring highly oxygenated cyclobutane rings, with a specific focus on oxetane and 1,2-dioxetane motifs. It presents the structures and biological activities of compounds containing these rings, highlighting their contribution to molecular stability and pharmacological potency. Through detailed case studies and recent research findings, it has been demonstrated that these oxygen-rich rings enhance the molecular diversity and biological efficacy of natural products, potentially offering new avenues for drug development. Notably, these compounds are predominantly synthesized by microorganisms and can also be found in extracts from fungi, plants, and certain marine invertebrates. Compounds with oxetane and 1,2-dioxetane rings are primarily noted for their strong antineoplastic properties, among other biological activities. In contrast, most 1,2-dioxetanes exhibit potent antiprotozoal effects. It is important to note that 1,2-dioxetanes often serve as intermediate products in oxidation reactions, characterized by their instability and propensity to decompose into new compounds.

A highly efficient deep red (DR) emitting organic solid based on a dicyano-phenylenevinylene derivative was reported. The structural and spectroscopic properties of the solid have been described in terms of crystallographic data and time dependent DFT analysis. A noteworthy fluorescence quantum yield of 53% was observed for the brightest emitter cast into solid films. This result can be explained in terms of aggregation-induced emission (AIE) effect.

There have been many discussions on the globalisation of SMEs, but it is true that there is not enough academic achievement after such the study of Born global (BG) ventures. The internationalisation of SMEs (Small and Medium Enterprises) is not easy because they lack resources or capabilities compared to multinational corporations. This study investigated the role of government in assisting the internationalisation of SMEs. In particular, SMEs lacked the ability to acquire market-oriented information, so we’ve established the scheme of efficient information support system for the internationalisation of SMEs. In other words, we proposed an information analysis system through the establishment of a relational database constructed for market-oriented information support. KISTI (Korea Institute of Science and Technology Information), which is one of the government-funded research institutes in the Republic of Korea, provided information support to the SMEs dealing with hydrazine related products. This study suggests this case for the market-oriented information support of the government in the internationalisation of SMEs. The research on information support of the government is meaningful in that it suggests a way to support SMEs in practical level.

The objective of this study was to compare the effectiveness of a professional-oriented education approach to traditional teaching methods among high school secondary students in Kazakhstan in aligning students to their suitable career education track. The study utilised a mechanics physics course to assess both approaches and involved two groups of students over 26 months - a control group (n=58) and an experimental group (n=57). Quantitative data was collected through a Mechanics Physics Test administered before and after the teaching and learning class. In Kazakhstan, students will be aligned directly with either secondary vocational education, the initial vocational education track, or the general education track, which relies on the final performance of their secondary school. The findings indicated that both teaching methods improved the student's performance, but the experimental group exhibited a significantly higher level of improvement than the control group. This study shows that a professional-oriented education approach can clearly align students with their interests and strengths and help them pursue their desired careers confidently. This approach enables students to make informed decisions about their future studies and career paths, reducing costs and saving time for schools and governments—implications and, to a further extent, the study is also discussed.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the analysis as well as theoretical considerations concerning to design of gear size ranges. This analysis consists in decomposition of the designed artefact (a gear) according to the rule “from general to details view”. The basics of the object-oriented analysis were formulated. Furthermore, design phases and the objects related to theses phases were discussed. The following models have been considered: hierarchical model, entity-relationship model, data-flow model and object model. Analysis is additionally connected with interactions between particular design phases.

Boost-derived converters are most popular in Power Factor Correction AC-DC conversion applications and alternative energy generation systems. The proper operation of such converters relies on housekeeping power supplies providing auxiliary power for their control circuitry. The purpose of this study is to present a design-oriented analysis of a simple, passive, isolated, self-bias circuit that can provide a stabilized voltage for the control circuits of boost-derived converters. The circuit’s output voltage inherently follows the main regulated output and therefore, does not require an additional active control. The paper presents a detailed analysis of the circuit and offers design guidelines. Following the presentation of the basic idea several variations of the circuit, that can be used in special applications, are presented. The feasibility of the proposed bias circuits was verified by simulation and experiment on a laboratory prototype.

Pairs of potential and flow variables have long been established for interfacing object-oriented component models of physical systems. Recently, however, the use of triplets has been discovered for the purpose of robust modeling. New and powerful Modelica libraries have been developed such as the DLR ThermoFluid Stream library or the introduction of the Dialectic Mechanics library. Their use of triplets is entangled with a special modeling approach that uses Linear Implicit Equilibrium Dynamics. In this paper, we study the basic motivation of this approach, its benefits and drawbacks before we finally demonstrate how it beneficially impacts the generation of corresponding simulation code.

Modern cryptographic protocols such as zero-knowledge proofs and secure multi-party computation have increased the demand for a novel category of symmetric primitives. These primitives are not optimized for traditional platforms such as servers, microcontrollers, and desktop computers but rather for their ability to be implemented in arithmetic circuits. To enable efficient arithmetic operations, they define operations over larger finite fields and use low-degree invertible functions to construct their non-linear layers. Grendel is an arithmetization-oriented permutation that leverages the Legendre Symbol to enhance the growth of algebraic degrees in its non-linear layer. In this paper, we present a preimage attack on the sponge hash function instantiated with the full rounds of the Grendel permutation using algebraic methods. We introduce a technique that allows us to eliminate two full rounds of substitution permutation networks (SPN) in the sponge hash function with minimal or no additional cost. This method can be combined with univariate root-finding techniques and Gröbner basis attacks to break the number of rounds claimed by the designers. By utilizing this strategy, our attack achieves an improvement of two additional rounds compared to the previous state-of-the-art attack. While not breaking its security margin, it allows us to further understand the design and analysis of such cryptographic primitives.

Fluorine represents a privileged building block in pharmaceutical chemistry. Diethylaminosulfur-trifluoride (DAST) is a reagent commonly used for replacement of alcoholic hydroxyl groups with fluorine and is also known to catalyze water elimination and cyclic Beckmann-rearrangement type reactions. In this work we aimed to use DAST for diversity-oriented semisynthetic transformation of natural products bearing multiple hydroxyl groups to prepare new bioactive compounds. Four ecdysteroids, including a new constituent of Cyanotis arachnoidea, were selected as starting materials for DAST-catalyzed transformations. The newly prepared compounds represented combinations of various structural changes DAST was known to catalyze, and a unique cyclopropane ring closure that was found for the first time. Several compounds demonstrated in vitro antitumor properties. A new 17-N-acetylecdysteroid (13) exerted potent antiproliferative activity and no cytotoxicity on drug susceptible and multi-drug resistant mouse T-cell lymphoma cells. Further, compound 13 acted in significant synergism with doxorubicin without detectable direct ABCB1 inhibition. Our results demonstrate that DAST is a versatile tool for diversity-oriented synthesis to expand chemical space towards new bioactive compounds.

Hydrologic models are conventionally constrained and evaluated using point measurements of streamflow, which represents an aggregated catchment measure. As a consequence of this single objective focus, model parametrization and model parameter sensitivity are typically not reflecting other aspects of catchment behavior. Specifically for distributed models, the spatial pattern aspect is often overlooked. Our paper examines the utility of multiple performance measures in a spatial sensitivity analysis framework to determine the key parameters governing the spatial variability of predicted actual evapotranspiration (AET). Latin hypercube one-at-a-time (LHS-OAT) sampling strategy with multiple initial parameter sets was applied using the mesoscale hydrologic model (mHM) and a total of 17 model parameters were identified as sensitive. The results indicate different parameter sensitivities for different performance measures focusing on temporal hydrograph dynamics and spatial variability of actual evapotranspiration. While spatial patterns were found to be sensitive to vegetation parameters, streamflow dynamics were sensitive to pedo-transfer function (PTF) parameters. Above all, our results show that behavioral model definition based only on streamflow metrics in the generalized likelihood uncertainty estimation (GLUE) type methods require reformulation by incorporating spatial patterns into the definition of threshold values to reveal robust hydrologic behavior in the analysis.

Mechanically homogenized composite of expanded graphite and cobalt(II) rhenate(VII) has been described. Cobalt(II) rhenate(VII) was obtained in a reaction of perrhenic acid with cobalt(II) nitrate. A simple mortar homogenization method was used to enhance intercalation of cobalt species within carbon matrix. The specific capacity of composite was enhanced by 50% in comparison to bare expanded graphite. The electrochemical characteristic was significantly improved including better cyclability, lower resistance of electrode material, lower iR drop, with respect to expanded graphite without cobalt(II) rhenate(VII) active species. Expanded graphite with its unique specific surface area and pore size diameter was proved as potential and cheap carbon support.

Recognizing highly occluded objects is believed to arises from the interaction between the brain's vision and cognition controlling areas, although supporting neuroimaging data is currently limited. To explore the neural mechanism during this activity, we conducted an occlusion object recognition experiment using functional magnetic resonance imaging (fMRI). During magnet resonance examinations, 66 subjects engaged in object recognition tasks with three different occlusion degrees. Generalized linear model (GLM) analysis showed that the activation degree of occipital lobe (inferior occipital gyrus, middle occipital gyrus, and occipital fusiform gyrus) and dorsal anterior cingulate cortex (dACC) was related to the occlusion degree of the objects. Multivariate pattern analysis (MVPA) further unearthed a considerable surge in classification precision when dACC activation was incorporated as a feature. This suggested the combined role of dACC and occipital lobe in occluded object recognition tasks. Moreover, psychophysiological interaction (PPI) analysis disclosed that functional connectivity (FC) between the dACC and the occipital lobe was enhanced with increased occlusion, highlighting the necessity of FC between these two brain regions in effectively identifying exceedingly occluded objects. In conclusion, these findings contribute to understanding the neural mechanisms of highly occluded objects recognition, augmenting our appreciation of how the brain manages incomplete visual data.

A microwave assisted method for synthesis of 2-substituted benzimidazoles has been developed. The combination of molar ratio N-phenyl-o-phenylenediamine:benzaldehyde (1:1) using microwave irradiation and only 1% mol of Er(OTf)3 provide an efficient, environmental and mild access to a diversity of benzimidazoles under solvent-free conditions.

Nowadays, an increasing number of heterocyclic-based drugs found application in medicinal chemistry and, in particular, as anticancer agents. In this context, oxadiazoles, five-membered aromatic rings, emerged for their interesting biological properties. Modification of oxadiazole scaffolds represents a valid strategy to increase their anticancer activity, especially on 1,2,4 and 1,3,4 regioisomers. In the last years, an increasing number of oxadiazole derivatives, with remarkable cytotoxicity for several tumor lines, were identified. Structural modifications, that ensure higher cytotoxicity towards malignant cells, represent a solid starting point in the development of novel oxadiazoles-based drugs. To increase the specificity of this strategy, outstanding oxadiazole scaffolds have been designed to selectively interact with biological targets, including enzymes, globular proteins and nucleic acids, showing more promising antitumor effects. In the present work, we aim to provide a comprehensive overview of the anticancer activity of these heterocycles, describing their effect on different targets and highlighting how their structural versatility has been exploited to modulate their biological properties.

Nutrient recovery technologies have been constantly developed and optimised to address challenges in water and wastewater management, sanitation, and agri-food systems, while promoting sustainable management of resources, and circular phosphorus economy. However, these technologies have been rarely explored beyond laboratory-scale in developing countries where it is mostly needed, such as the Philippines. In this study, a nutrient recovery batch reactor system was installed at a local farm to process raw septage from an onsite sanitation system, septic tank, to recover a high-value fertiliser for local crop production. The batch reactor was used for two processes; acid hydrolysis for pre-treatment of septage and chemical precipitation to recover phosphorus fertiliser (RPF). The recovered fertiliser was then applied to produce eggplants and tomatoes, which are the common crops grown in the farm. Results show that an average of 290 g of recovered RPF was produced for every 100 L of raw septage processed. With hydrolysis, 77% of the phosphate concentration were released as phosphates from the solid component of the raw septage. About 98.5% of phosphates were recovered from the hydrolysed septage. The RPF when applied to the farm’s eggplants and tomatoes have yields comparable to that of the commercial fertilisers. This study was able to demonstrate the potential of a resource-oriented sanitation system that promotes nutrient recycling toward sustainable agriculture that further leads to meeting the United Nation’s Sustainable Development Goals, particularly Zero Hunger (goal 2), Clean Water and Sanitation (goal 6), Sustainable Cities and Communities (goal 11), and Responsible Consumption and Production (goal 12).

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

Aiming at the problem of small size of some spots on apple leaves and the difficulty of accurate detection of spot targets brought by the complex background of the orchard, this paper takes the alternaria leaf spot, rust, brown spot, grey spot and frog eye leaf spot on apple leaves as the research object, and proposes a high-accuracy detection model YOLOv5-Res and lightweight detection model YOLOv5-Res4 are proposed. Firstly, a multiscale feature extraction module ResBlock is designed by combining the Inception multi-branch structure and ResNet residual idea. Secondly, a lightweight feature fusion module C4 is designed to reduce the number of model parameters while improving the detection ability of small targets. Finally, a parameter streamlining strategy based on optimized model architecture is proposed. The experimental results show that the performance of YOLOv5-Res model and YOLOv5-Res4 model is significantly improved, the [email protected] value is improved by 2.8% and 2.2% compared with YOLOv5s model and YOLOv5n model, respectively, and the size of YOLOv5-Res model and YOLOv5-Res4 model is only 10.8MB and 2.4MB, and the number of model parameters is reduced compared with YOLOv5s model and YOLOv5n model. counts are reduced by 22% and 38.3% compared to the YOLOv5s model and YOLOv5n model.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

The adaptation stress experienced by overseas dispatched employees has serious implications for their physical and mental health and work performance. This study aimed to investigate the impact of resource-oriented music listening on work stress among overseas dispatched employees. The study recruited 10 participants of different ages and occupations who had worked abroad for at least 3 years. Five sessions of personalized resource-oriented music listening, and interviews were conducted. The Global Assessment of Recent Stress Scale (GARS) and Job Stress Scale (JSS) were used to measure stress before and after the intervention. Results showed that participants' work stress and perceived stress were significantly reduced after the music therapy intervention. The study also found that 'awareness' and 'self-acceptance' were factors that reduced regulatory stress among overseas dispatched employees. This study highlights the potential of resource-oriented music listening as a useful tool to address workplace stress and promote the well-being of expatriate employees.

Droplet epitaxy allows the efficient fabrication of a plethora of 3D, III-V-based nanostructures on different crystalline orientations. Quantum dots grown on (311)A-oriented surface are obtained with record surface density, with or without a wetting layer. These are appealing features for quantum-dot lasing, thanks to the large density of quantum emitters and a truly 3D lateral confinement. However, the intimate photophysics of this class of nanostructures has not yet been investigated. Here we address the main optical and electronic properties of s-shell excitons in individual quantum dots grown on (311)A substrates with photoluminescence spectroscopy experiments. We show the presence of neutral exciton and biexciton as well as positive and negative charged excitons. We investigate the origins of spectral broadening, identifying them in spectral diffusion at low temperature and phonon-interaction at higher temperature, the presence of fine interactions between electron and hole spin, and a relevant heavy-hole/light-hole mixing. We interpret the level filling with a simple Poissonian model reproducing the power excitation dependence of the s-shell excitons. These results are relevant for the further improvement of this class of quantum emitters and their exploitation as single photon sources for low density samples as well as for efficient lasers for high density samples.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

Whole cell biosensors could serve as eco-friendly and cost-effective alternatives for detecting potentially toxic bioavailable heavy metals in aquatic environments. However, they often fail to meet practical requirements due to an insufficient limit of detection (LOD) and high background noise. In this study, we designed a synthetic genetic circuit specifically tailored for detecting ionic mercury, which we applied to environmental samples collected from artisanal gold mining sites in Peru. We developed two distinct versions of the biosensor, each utilizing a different reporter protein: a fluorescent biosensor (Mer-RFP) and a colorimetric biosensor (Mer-Blue). Mer-RFP enabled real-time monitoring of the culture’s response to mercury samples using a plate reader, whereas Mer-Blue was analysed for colour accumulation at the endpoint using a specially designed, low-cost camera set up for harvested cell pellets. Both biosensors exhibited negligible baseline expression of their respective reporter proteins and responded specifically to HgBr2 in pure water. Mer-RFP demonstrated a linear detection range from 1 nM to 1 μM, whereas Mer-Blue showed a linear range from 2 nM to 125 nM. Our biosensors successfully detected a high concentration of ionic mercury in the reaction bucket where artisanal miners produce a mercury-gold amalgam. However, they did not detect ionic mercury in the water from active mining ponds, indicating a concentration lower than 3.2 nM Hg2+ -a result consistent with chemical analysis quantitation. Furthermore, we discuss the potential of Mer-Blue as a practical and affordable monitoring tool, highlighting its stability, reliance on simple visual colorimetry, and the possibility of sensitivity expansion to organic mercury.

The generalized dual-kinetic-balance approach for axially symmetric systems is employed to solve the two-center Dirac problem. The spectra of one-electron homonuclear quasimolecules are calculated and compared with the previous calculations. The analysis of the monopole approximation with two different choices of the origin is performed. Special attention is paid to the lead and xenon dimers, Pb82+–Pb82+–e− and Xe54+–Xe54+–e−, where the energies of the ground and several excited σ-states are presented in the wide range of internuclear distances. The developed method provides the quasicomplete finite basis set and allows for construction of the perturbation theory, including within the bound-state QED.

The interest in dry EEG electrodes has increased in recent years and especially as everyday suitability earplugs for measuring drowsiness or focus of auditory attention. However, the challenge is still the need for a good electrode material, which is reliable and can be easily processed for highly personalized applications. Laser processing as used here is a fast and very precise method to produce personalized electrode configurations that meet the high requirements of in-ear EEG electrodes, for example. The arrangement of the electrodes on the very flexible and compressible mats allows an exact alignment of the electrodes to the ear mold and contributes to a high wearing comfort, as no edges or metal protrusions are present. For better transmission properties, an adapted coating process for surface enlargement of platinum electrodes is used, which allows easy control of the thickness and growth form of the porous layer. The porous platinum-copper alloy is chemically very stable, shows no exposed copper residues and enlarges the effective surface area by 40. In a proof-of-principle experiment, these porous platinum electrodes could be used to measure the Berger effect in a dry state using just one ear of a test person. Their signal-to-noise ration and frequency transfer function is comparable to gel-based silver/silver chloride electrodes.

Opportunistic Routing is a promising paradigm that has been proposed for efficient and reliable transfer of data packets in mobile ad hoc networks. This routing strategy takes advantage of the broadcasting nature of the wireless medium to increase the number of probable forwarding devices and improves the reliability of data transfer in the network. Opportunistic Routing utilizes the reception of the same broadcasted packet at multiple devices in the network and selects one best forwarder dynamically from the set of multiple receivers. A number of opportunistic routing protocols have been proposed over these years for effective data delivery in ad hoc networks. But as the speed and mobility of devices increases in the network, performances of the existing opportunistic routing protocols degrade considerably, leading to reduced Quality of Service and poor transmission efficiency. The exceptional potential of opportunistic routing is thus underutilized. In this research we introduce Optimized Opportunistic Routing (OOR) strategy that guarantee excellent Quality of Service and high transmission efficiency to the latest applications using opportunistic routing for communication in highly dynamic ad hoc networks. Simulation results show that our method achieve significant performance improvements compared to all other existing opportunistic routing protocols in highly dynamic mobile ad hoc networks.

Over the years, scarcity of fresh potable water has increased the demand for clean water. Meanwhile, with the advent of nanotechnology, the use of nanomaterials for photocatalytic degradation of pollutants in wastewaters has increased. Herein, a new type of nanohybrids of La and Mn co-doped bismuth ferrite (BiFeO₃) nanoparticles embedded into transition metal carbide sheets (MXene) were prepared by a low-cost double solvent sol-gel method, and investigated for their photocatalytic activity. The photoluminescence results showed that pure BFO has highest electron hole recombination rate as compared to all the co-doped BFO/MXene nanohybrids. The larger surface area and higher electron-hole pair generation rate provides suitable environment for fast photo-degradation of organic molecules. The band gap of the prepared nanohybrids was tuned to 1.96 eV having largest BiFeO₃ surface area (147 m²g⁻¹) reported till date. Moreover, the BLFO/MXene and BLFMO-5/Mxene degraded the 92% organic pollutant from water in dark and remaining in light spectrum as compare to undoped BFO/Mxene due to enhancement of the surface area and electron-hole recombination rate upon doping. Therefore, these synthesized nanohybrids could be a promising candidate for photocatalytic applications in future.

Predicting nurse turnover is a growing challenge within the healthcare sector, profoundly impacting healthcare quality and the nursing profession. This study employs the Synthetic Minority Over-sampling Technique (SMOTE) to address class imbalance issues in the 2018 National Sample Survey of Registered Nurses (NSSRN) dataset and predict nurse turnover using machine learning (ML) algorithms. Four ML algorithms, namely logistic regression (LR), random forests (RF), decision tree (DT), and extreme gradient boosting (XGBoost), are applied to the SMOTE-enhanced dataset. The data is randomly split into an 80% training set and a 20% validation set. Eighteen carefully selected variables from the NSSRN database serve as predictive features, and the machine learning model identifies feature importance concerning nurse turnover. The study includes a performance comparison based on metrics such as Accuracy, Precision, Recall (Sensitivity), F1-score, and AUC. In summary, the results demonstrate that SMOTE-enhanced random forests (SMOTE_RT) exhibit the most robust predictive power, both in the classical approach (with all 18 predictive variables) and an optimized approach (utilizing eight key predictive variables). XGBoost, decision tree, and logistic regression follow in performance. Notably, age emerges as the most influential factor in nurse turnover, with working hours, EHR/EMR usability, individual income, and region also playing significant roles. This research offers valuable insights for healthcare researchers and stakeholders, aiding in selecting suitable ML algorithms for nurse turnover prediction.

Global severity maps of ongoing dengue epidemic and COVID-19 pandemic do not overlap. Countries with high dengue endemicity (>1.5 million cases/year) are observably less hit by COVID-19 in terms of infection, transmission and mortality. Based on non-overlap of dengue and COVID-19 severity maps and evidence of SARS-CoV-2 serological cross-reactions with dengue, we wonder whether immediate immunization of susceptible populations in Europe, North America and Asia (China, Iran) with available live-attenuated dengue vaccines, will cue the anti-viral immune response to thwart COVID-19 (viral interference). Risk of developing post-vaccination “Antibody-dependent Enhancement” is low as dengue is not endemic in the aforesaid regions.

Compounds with tyrosinase inhibitory efficacy could be effective as depigmenting agents. Although a large number of natural and synthetic tyrosinase inhibitors have been reported, few of them are used as skin-whitening agents due to poor activity and safety concerns. 3-(2,4-Dihydroxyphenyl)propionic acid (DPPA), a naturally occurring compound isolated from Ficus carica, was previously discovered as a moderate tyrosinase inhibitor. In this study, the structure-activity relationship study of DPPA was conducted. Compound 3g, with the 2,4-resorcinol subunit and terminal hydrophobic di-butylamino group, was identified with low nanomolar enzymatic IC₅₀ value. Additionally, compound 3g could effectively reduce melanin levels in B16-F10 melanoma cells treated with α-melanocyte-stimulating hormone (α-MSH) without affecting cell viability and proliferation. All these results indicated that compound 3g could be considered as a promising candidate for the treatment of diseases associated with hyperpigmentation.

Detecting rotated objects in remote sensing images poses a substantial challenge. These images usually cover a wide field of view, containing diverse and complex backgrounds with variously sized ground objects densely distributed. Therefore, identifying objects of interest in remote-sensing images is challenging. While integrating Convolutional Neural Networks (CNNs) and Transformer networks has exhibited progress in detecting rotated objects, there is still scope for enhancing feature extraction and fusion. To address this issue, we propose a feature extraction module, a feature context aggregation module, and a multi-scale feature fusion module. Initially, we substitute the Spatial Pyramid Pooling Bottleneck (SPPFBottleneck) with a new module aimed at extracting multi-scale features, thereby enhancing the detection of small objects in complex backgrounds. Next, we develop a novel module for the multi-scale fusion of contextual information within feature maps, extracting valuable information. Finally, we combine the original features with the fused ones to prevent the loss of specific features in the fusion process. We refer to our newly proposed model as the "Multi-scale Feature Context Aggregation Network" (MFCANet). We assess our approach on three challenging remote sensing datasets: MAR20, SRSDD, and HRSC. Comprehensive experimental results show that our method surpasses baseline models by 2.13%, 10.28%, and 1.46% mAP on the MAR20, SRSDD, and HRSC datasets, respectively.