Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

The Hollow fiber membrane contactor (HFMC) is an intensification process that combines membrane and absorption technologies, being a technology in expansion, so the dynamics of this process is crucial for an increase in industrial scale-up. In this manuscript a rigorous dynamic model of an HFMC is developed and simulated in Python software for the absorption of post-combustion CO2 using a monoethanolamine (MEA) solution, which was validated using available data in literature in steady state. Dynamic simulations were performed to analyze the model's capability to predict the effect of disturbances on the responses of CO2 capture ratio and loading. Four distinct experiments were conducted by step changes and pulse disturbances at the following variables: gas and liquid volumetric flow rates, CO2 composition in flue gases, and CO2 lean load. The gas phase showed a faster response compared to the liquid. The CO2 capture ratio and rich loading presented opposite responses when disturbing both liquid flows, and for the composition and lean loading variations, the capture ratio presented an inverse response characteristic, while the loading showed a delayed response. As the model proved to be capable of returning to the reference state, it can potentially be used for control studies purposes.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

A realistic implementation of an all-fiber CO₂ sensor, using 74 cm of hollow core PCF fiber as the cavity for light/gas interaction, has been implemented. It is based on CO₂ absorbance in the 2 μm region. The working range is from 2% to 100% CO₂ concentration at 1 atm total pressure. The response time obtained was 10 min. The use of an FBG tuned fiber ring laser, specifically designed for this application, is discussed and preliminary results with this laser are also presented.

Membrane-based beverage dealcoholization is a successful process for producing low- and non-alcoholic beer and represents a fast-growing industry. Polyamide NF and RO membranes are commonly applied for this process. Polyelectrolyte multilayer (PEM) NF membranes are emerging as industrially relevant species and their unique properties (usually hollow fiber geometry, high and tunable selectivity, low fouling) underlines the importance of testing them in the food industry as well. To test PEM NF membranes for beer dealcoholization, at small pilot scale we dealcoholized filtered and unfiltered lager beer with the tightest available commercial polyelectrolyte multilayer NF membrane (NX Filtration dNF40), which has a MWCO=400Da which is quite high for these purposes. Dealcoholization is possible with a reasonable flux (10 LMH) at low pressures (5-8.6 bar) with a real extract loss of 16-18% and an alcohol passage of ~100%. Inorganic salt passage is high (which is typical for PEM NF membranes), which greatly affected beer flavor. During the dealcoholization process, the membrane underwent changes which substantially increased its salt rejection values (MgSO4 passage decreased 4-fold) while permeance loss was minimal (less than 10%). According to our sensory examination, the process yielded an acceptable flavored beer which could be greatly enhanced by the addition of the lost salts and glycerol.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

There is a huge interest in developing novel hollow fiber (HF) membranes able to modulate neural differentiation to produce in vitro blood-brain barrier (BBB) models for biomedical and pharmaceutical research, due to the low cell-inductive properties of the polymer HFs used in current BBB models. In this work, poly(ε-caprolactone) (PCL) and composite PCL/graphene (PCL/G) HF membranes were prepared by phase inversion and were characterized in terms of mechanical, electrical, morphological, chemical, and mass transport properties. The presence of graphene in PCL/G membranes enlarged the pore size and the water flux and presented significantly higher electrical conductivity than PCL HFs. Biocompatibility assay showed that PCL/G HFs significantly increased C6 cells adhesion and differentiation towards astrocytes, may be attributed to their higher electrical conductivity in comparison to PCL HFs. On the other hand, PCL/G membranes produced a cytotoxic effect on the endothelial cell line HUVEC presumably related with a higher production of intracellular reactive oxygen species induced by the nanomaterial in this particular cell line. These results prove the potential of PCL HF membranes to grow endothelial cells and PCL/G HF membranes to differentiate astrocytes, the two characteristic cell types that could develop in vitro BBB models in future 3D co-culture systems.

The processability of conductive polymers such as polyaniline (PANI) still poses a challenge due to their properties. The use of stabilizers, compatible and able to interact with PANI, to obtain dispersible and stable colloids is described in this work. To this aim, potato starch has been used as a steric stabilizer for the preparation of polyaniline (emeraldine salt, ES)/starch biocomposites, by exploiting oxidative polymerization of aniline in aqueous solutions containing different ratios of aniline and starch (% w/w). The polyaniline/starch biocomposites were subjected to structural and spectroscopic analyses, thermal analysis, morphological analysis and electrochemical analysis. The samples were then tested for their dispersibility/solubility in various organic solvents. The results showed the formation of PANI/starch biocomposites with an overall smaller size than starch particles, with improved aqueous dispersion and solubility in organic solvents. Although X-ray diffraction and differential scanning calorimetry analyses indicated a loss of crystallinity in the biocomposites, the cyclic voltammetry tests showed that all PANI ES/starch biocomposites display improved redox exchange properties.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The efficient extraction of phthalate acid esters (PAEs) is challenging due to their extremely low concentration, complicated matrices and hydrophilicity. Herein, hol-low microspheres, as an ideal coating, possesses significant potential for solid-phase microextraction (SPME) due to their fascinating properties. In this study, multi-walled carbon nanotubes hollow microspheres (MWCNTs-HMs) were utilized as a fiber coating for the SPME of PAEs from tea beverages. MWCNTs-HMs were ob-tained by dissolving the polystyrene (PS) cores with organic solvents. Interestingly, MWCNTs-HMs well maintain the morphology of the precursors MWCNTs@PS. The layer-by-layer (LBL) assembly of MWCNTs on PS microsphere templates was ac-quired through electrostatic interactions. Six PAEs, di-ethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-2-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DOP), were se-lected as target analytes for assessing the efficiency of the coating for SPME. The stirring rate, sample solution pH and extraction time were optimized by using the Box-Behnken design. Under optimal working conditions, the proposed MWCNTs-HMs/SPME was coupled with gas chromatography-tandem mass spec-trometry (GC-MS/MS) to achieve high enrichment factors (118–2137), wide linearity (0.0004-10 μg L-1), low limits of detection (0.00011-0.0026 μg L-1) and acceptable recovery (80.2%-108.5%) for the detection of PAEs. Therefore, the MWCNTs-HMs coated fibers are promising alternatives in the SPME method for the sensitive detec-tion of PAEs at trace levels in tea beverages.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

This paper discusses the basic concepts of phase dislocations and vortex formation in the electric fields of fundamental air core mode of hollow core waveguides with specific types of rotational symmetry of the core – cladding boundary. Analysis of the behavior of the electric field phase in the transmission bands shows that the mechanism of light localization in the hollow core waveguides with discrete rotational symmetry of the core – cladding boundary cannot be completely described by the ARROW model. For an accurate description of the phase behavior, it is necessary to account for phase jumps of the magnitude of π when passing through the phase dislocations.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Introduction: Atrial fibrillation (AF) is a common cardiac arrhythmia whose prevalence rises with age and is linked to increased morbidity and mortality due to the risk of thromboembolism. Management typically involves anticoagulation and rhythm control, but the treatment of elderly patients with multiple comorbidities requires careful consideration of drug side effects and interactions. Cibenzoline, a Vaughan-Williams class IA antiarrhythmic, is effective against AF but has risks of toxicity, especially in older people and those with renal impairment, due to its renal excretion and prolonged half-life in these populations. Discussion: This paper presents a case of an 80-year-old woman with paroxysmal AF who suffered cardiac arrest due to cibenzoline toxicity despite receiving standard adjusted dosages. The patient's cibenzoline blood concentration was significantly higher than the therapeutic range, leading to cardiotoxicity, which was exacerbated by drug interactions with bisoprolol and edoxaban, both metabolized by the CYP3A4 enzyme. Venoarterial extracorporeal membrane oxygenation (V-A ECMO) and intra-aortic balloon pump (IABP) successfully managed the cardiac arrest. This case emphasizes the unpredictable pharmacokinetics of cibenzoline in elderly patients with renal impairment and the need for vigilant therapeutic drug monitoring to avoid adverse events. Conclusions: Cibenzoline can pose a significant risk of severe toxicity in elderly patients with renal impairment, and drug interactions may potentiate this risk. The paper underscores the importance of careful dose adjustment and monitoring of drug levels in this population. In cases of cibenzoline-induced cardiac arrest, V-A ECMO and IABP are effective treatment modalities. The case study serves as a critical reminder for clinicians to remain vigilant for drug-induced complications and to apply aggressive supportive treatments when necessary.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

The harmful nature of high concentrations of antibiotics to humans and animals requires urgent development of novel materials and techniques for their absorption. In this work, CTAB (Cetyltrimethyl Ammonium Bromide)-assisted synthesis of ZIF-8 (zeolitic imidazolate framework) derived hollow carbon (ZHC) was designed, prepared and used as a high-performance adsorbent, further evaluated by Langmuir and Freundlich isothermal adsorption experiments, dynamic analysis as well as theoretical calculation. The maximum capacities of ZHC on adsorbing tetracycline (TC), norfloxacin (NFO) and levofloxacin (OFO) are 267.3, 125.6 and 227.8 mg g^-1, respectively, which delivers superior adsorptive performance when compared to widely studied inorganic adsorbates. The design concept of ZIFs-derived hollow carbon material provides guidance and insights for the efficient adsorbent of environmental antibiotics.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Artificial membrane systems can serve as models to investigate molecular mechanisms of different cellular processes, including transport, pore formation, and viral fusion. However, the current simulacrums such as SUVs, GUVs, and the supported lipid bilayers suffer from issues, namely high curvature, heterogeneity, and surface artefacts, respectively. Freestanding membranes provide a facile solution to these issues, but current systems developed by various groups use silicon or aluminium oxide wafers for fabrication that involves access to a dedicated nanolithography facility and high cost while conferring poor membrane stability. Here, we report the development, characterization and applications of an easy-to-fabricate suspended lipid bilayer (SULB) membrane platform leveraging commercial track-etched porous filters (PCTE) with defined microwell size. Our SULB system offers a platform to study the lipid composition-dependent structural and functional properties of membranes with exceptional stability in a high throughput fashion. With dye entrapped in PCTE microwells by SULB, we show that sphingomyelin significantly augments the activity of pore-forming toxin, Cytolysin A (ClyA) and the pore formation induces lipid exchange between the bilayer leaflets. Further, we demonstrate high efficiency and rapid kinetics of membrane fusion by dengue virus in our SULB platform. Our suspended bilayer membrane mimetic offers a novel platform to investigate a large class of biomembrane interactions and processes.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Nowadays, it is highly desired to develop highly active and humidity resistive ozone decomposition catalyst to eliminate the ozone contaminant, one of the primary pollutants in air. In this work, a series of Cu2S hollow structured materials are rapidly synthesized using different structured Cu2O templates. The Cu2S from porous Cu2O shows the highest ozone catalytic decomposition efficiency of >95% to 400 ppm ozone with a weight hourly space velocity of 480,000 cm3g-1h-1 in dry air. Importantly, the conversion still keeps >85% in a high relative humidity of 90%. The mechanism is explored by diffusive reflectance infrared spectroscopy which shows the decomposition intermediate of O22-, and the X-ray photoelectron spectroscopy reveals the dual active site of both Cu and S. All these results show the effective decomposition of ozone by Cu2S especially in harsh environments, promising for active ozone elimination.

The non-linear analysis of hollow-core concrete slabs requires the use of advanced numerical techniques, proper constitutive models both for concrete and steel as well as particular computational skills. If prestressing, cracking, crack opening, material softening, etc. are also to be taken into account, then the computational task can far exceed the capabilities of an ordinary engineer. In order for the calculations to be carried out in a traditional design office, simplified calculation methods are needed. Preferably based on the linear finite element (FE) method with a simple approach that takes into account material nonlinearities. In this paper the simplified analysis of hollow-core slabs based on the generalized nonlinear constitutive law is presented. In the proposed method a simple decomposition of the traditional iterative linear finite element analysis and the non-linear algebraic analysis of the plate cross-section is used. Through independent analysis of the plate cross-section in different deformation states, a degraded plate stiffness can be obtained, which allows iterative update of displacements and rotations in the nodes of the FE model. Which in turn allows to update the deformation state and then correct translations and rotations in the nodes again. The results obtained from the full detailed 3D nonlinear FEM model and from the proposed approach are compared for different slab cross-sections. The obtained results from both models are consistent.

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite web from polylactic bicomponent fiber and natural fibers, cattail and kapok fiber, were prepared by hot-press method. Only the sheath region of the PLA bicomponent fiber melts, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared to its state before hot-pressing. Mechanical and physical properties of composite webs were evaluated. Composite webs created from kapok fiber displayed a creamy yellowish-white color, while those made from cattail fiber showed a yellowish-brown color. Composite webs exhibit hydrophobic properties when adding the natural fiber. The maximum natural fiber content, at a ratio of 30, can be incorporated into composite webs while preserving mechanical properties and proper water vapor permeability. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Mandibular critical size defect (CSD) due to pathological conditions, trauma, and congenital disease can not heal spontaneously and predominantly filled with fibrous tissue. Therefore, a Guided Bone Regeneration (GBR) combined with bone grafting can be performed. The researchers considered using Demineralized Dentin Material Membrane (DDMM) from bovine dentine as an alternative GBR. This study aimed to determine the amount of fibroblast and collagen density after DDMM and bone graft implantation on CSD. Thirty-six Rattus norvegicus rats were used as samples. Mandibular bone defect 5x5 mm was made, then filled with bone graft and covered with Bovine Pericardium Collagen Membrane (BPCM) in the control group and DDMM in the treatment group. Six samples were sacrificed on 7, 14, and 21 days post-surgical for histology examination. There were no significant differences in the amount of fibroblast and collagen density (p-value > 0,05). The amount of fibroblast is lower and the collagen density is higher in treatment group. DDMM has microporosity to prevent connective tissue ingrowth and dentine tubules to allow growth factors release. DDMM and bone graft implantation can reduce the amount of fibroblasts and increase collagen density of CSD which potentially being used as a CSD alternative treatment for bone regeneration.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

Biological membranes are fascinating. Santiago Ramón y Cajal, who received the Nobel prize in 1906 together with Camillo Golgi for their work on the nervous system, wrote “[..]in the study of this membrane[..] I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life”[1]. The visualization and conceptualization of these biological objects have profoundly shaped many aspects of modern biology, drawing inspiration from experiments, computer simulations, as well as from the imagination of scientists and artists. The aim of this review is to provide a fresh look on current ideas of biological membrane organization and dynamics by discussing selected examples across fields [1] The full quotation is “I must not conceal the fact that in the study of this membrane I for the first time felt my faith in Darwinism (hypothesis of natural selection) weakened, being amazed and confounded by the supreme constructive ingenuity revealed not only in the retina and in the dioptric apparatus of the vertebrates but even in the meanest insect eye. There, in fine, I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life.” from the autobiography Recollections of My Life.

The most common and taught membrane theory assumes that the membrane behaves as a kind of electrical capacitance that is exposed to an electrical current generated by an ionic flow. If this statement is verifiable, it can be confirmed by the laws of physics, mathematics and in particular electricity. We will demonstrate that this hypothesis is not verified and that it is necessary to modify biophysics according to already established and experimentally verified principles of physics.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

This study investigates the unique morphology and mechanical properties of multi-jet electrospun cashew gum (CG) when combined with high molecular weight polyethylene oxide (PEO) and glycerol. Cashew gum (CG) is an inexpensive, non-toxic polysaccharide derived from Anacardium occidentale trees. Initially, the electrospinnability of aqueous solutions of cashew gum alone or in combination with PEO was evaluated. It was found that cashew gum alone was not suitable for electrospinning; thus, adding a small quantity of PEO was needed to create the necessary molecular entanglements for fiber formation. By using a single emitter with a CG:PEO ratio of 85:15, straight and smooth fibers with some defects were obtained. However, additional purification of the cashew gum solution and the incorporation of glycerol as a plasticizer were necessary to produce defect-free straight and smooth fibers. Interestingly, when the optimized formulation was electrospun using multiple simultaneous emitters, thicker aligned fiber bundles were achieved. Moreover, the resulting oriented fiber mats exhibited unexpectedly high elongation at break at ambient conditions. These findings highlight the potential of this bio-polysaccharide-based formulation for non-direct water contact applications requiring elastic properties.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

Orificed Hollow Cathodes are electric devices necessary for the functioning of common plasma thrusters for space applications. From their reliability mainly depends the success of a spacecraft’s mission equipped by electric propulsion. The development of plasma models is crucial in the evaluation of plasma properties within the cathodes that are difficult to measure due to the small dimensions. Many models, based on non-linear system of plasma equations, have been proposed in the open literature. These are solved commonly by means of iterative procedures. This paper investigates the possibility to solve them by means of Particle Swarm Optimization method. The results of the validation tests confirm the expected trends for all the unknowns; the confidence bound of the discharge current as function of mass flow rate is very narrow (2÷5V), moreover the results match very well the experimental data except at the lowest mass flow rate (0.08mg/s) and discharge current (1A), where the computations underpredict the discharge current to the utmost by 40%; the highest data dispersion regards the plasma density in the emitter region (± 20 % of the average value) and the wall temperatures (± 50K respect to the average values) of orifice and insert; those of the others variables are very tiny.

Road infrastructure is a key public asset because it benefits the social and economic development of any country. It plays an important role for the development of the industrial complex, the production sector and the road surfaces of transport roads should be of high quality, have a long service life. Road infrastructure, as well as all infrastructure, requires preservation, maintenance and repair. There are special requirements for the roadway that must be observed during construction or repair. This article is devoted to a detailed study of the use of fiber optics sensors (FOS) based on the fiber Bragg grating (FBG) for road surface monitoring. Such a fiber sensor consisting of a fiber Bragg grid and a pair of grids can offer the possibility of simultaneous measurement of deformation and temperature for monitoring the pavement. Temperature and deformation measurements were carried out by installing a sensor on the surface of a made asphalt sample. The built-in fiber sensor based on FBG provides important information about how the pavement structure can withstand the load, subsidence of soil, timely implement road safety and stability measures evaluate and predict the service life of the pavement. The results of the study showed that the synchronicity, repeatability and linearity of the characteristics of the fiber sensor are excellent. The difference between the experimental and theoretical results is about 7%. Thus, based on the results of the obtained data, the fiber sensor on the FBG can be used for monitoring, designing road surfaces and in general transport infrastructure.

Five years ago, the concept of addressed fiber Bragg structures (AFBS) was proposed, which simultaneously perform the functions of a two-frequency radiation shaper, the difference frequency of which is the AFBS address, and a sensitive element, since the value of the difference frequency is invariant to measured physical fields, and the set of difference frequencies, moreover, is orthogonal in the array of such sensors, enabling their address multiplexing. In this article, we provide an overview of the theory and technology of AFBS, including the structures with three or more spectral components with various combinations of difference frequencies, symmetrical and asymmetric, performing the functions of the address and converting information signals to the low-frequency range at the same time, along with other functions. The subjects of interrogation of these structures, their fabrication and calibration are discussed as well. We also consider a wide range of applications in which AFBS can be used, covering such areas as oil and gas production, power engineering, transport, medicine, etc. In addition, the prospects of AFBS further development are proposed.

Nutrition is crucial for the management of patients affected by chronic kidney disease (CKD) to slow down disease progression and to correct symptoms. The mainstay of the nutritional approach to renal patients is protein restriction coupled with adequate energy supply to prevent malnutrition. However, other aspects of renal diets, including fiber content, can be beneficial. This paper summarizes the latest literature on the role of different types of dietary fiber in CKD, with special attention to intestinal microbiota and the potential protective role of renal diets. Fibers have been identified based on aqueous solubility, but other features, such as viscosity, fermentability, and bulking effect in the colon should be considered. A proper amount of fiber should be recommended not only in the general population but also in CKD patients, to achieve an adequate composition and metabolism of intestinal microbiota and to reduce the risks connected with obesity, diabetes, and dyslipidemia.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

The utilization of eco-fonts for office printing is a sustainable, “green” printing concept, which has obvious economic benefits. As a result, it has a significant effect on environmental sustainability. This practice's fundamental problem is the decreased quality of text printed using eco-fonts compared to those printed with regular fonts. The aim of this research is eco-font efficiency estimation, i.e. determination of toner usage reduction level of inkjet-printed documents typed with this font type, as well as estimation of the extent humans perceive differences between text printed with eco-font and the one printed by its “non-eco“ equivalent. Combining the instrumental measuring method and digital image analysis, it was found that this simple principle (eco-font utilization) enables substantial toner usage reduction for an inkjet printing system. At the same time, a visual test showed that the visual experience of text printed using eco-font was sufficient. In addition, awareness of the benefits that eco-font utilization brings, change users’ attitude towards eco-font quality. The concept of removing the black pixel from this commonly used Thai font has a great potential for the sustainability printing process, and this simple solution could be applied to other languages as part of the GIT campaign.

The generation and maintenance of membrane potential is considered a fundamental element of the cellular machinery. They are based on elements of physics and chemistry. Mathematics is used to validate the equations and evaluate the results. However, this computation process can lead to a misunderstanding of the phenomena involved or to the masking of crucial events. It is even possible that the calculation no longer corresponds to the hypothesis considered. Membrane theory is no exception to these trivial considerations, which are essential for normal theory validation.

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

The membrane potential or resting potential of the neuron has been the subject of many studies. Although this theory explains the generation and maintenance of the membrane potential by direct or even facilitated diffusion, there are too many contradictions to doubt that these forces are sufficient or even at work in a process whose initial conditions are of rare complexity. The aim of this article is to show that already in the past, a competing theory has been developed whose hypothesis seems more scientifically sound. To confirm this last theory, Hirohisa Tamagawa carried out an experiment of great simplicity which makes it possible to invalidate the current theory and to question the teaching and the knowledge in Biology and Biophysics.

There are different treatment options in modern dentistry for the replacement of lost dentition. Of these the most upcoming and acceptable treatment option is Dental implants. The common problem usually with immediate implant placement in the anterior region is the post-operative soft tissue contour as a part of the bone modelling during healing. Hurzeler et al in 2010 introduced a new technique called the “socket shield technique”. This technique has been used as an alternative treatment modality for immediate implant placement in the aesthetic zone.This review articles provides a detailed information regarding the clinical concept of Root membrane technique.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Cotton fiber, a crucial and sustainable resource for global textile production, undergoes a complex five-stage developmental process, encompassing initiation, elongation, transition, secondary cell wall biosynthesis, and maturation. These elongated single-cell fibers originate from the outer ovule epidermis. The development of cotton fibers involves intricate changes in gene expression and physiological processes, resulting in a nearly pure cellulose product vital for the global cotton industry. Decoding genes associated with fiber development enhances our understanding of cotton fiber mechanisms and facilitates the cultivation of varieties with enhanced quality. In recent decades, advanced omics approaches, including genomics, transcriptomics, and proteomics, have played a pivotal role in identifying genes and gene products linked to cotton fiber development, including the MYB transcription factor family which coordinates cotton fiber development. Molecular studies have revealed transcription factors like MYB, WRKY, Homeodomain Leucine Zipper (HD-ZIP) and basic Helix-Loop-Helix (bHLH) influencing fiber initiation and elongation. The intricate interplay of phytohormones like auxin, gibberellic acid (GA), brassinosteroid (BR), jasmonic acid (JA), ethylene, abscisic acid (ABA), and cytokinin is explored, providing a comprehensive perspective on shaping cotton fibers. Numerous candidate genes and cellular processes affecting various aspects of fiber development hold promise for genetic engineering or marker-assisted breeding to improve fiber quality. This review presents a comprehensive overview of key achievements in cotton molecular biology, with a specific emphasis on recent advancements in understanding transcription factors and phytohormones involved in cotton fiber initiation and elongation.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

Endothelial cells are the crucial inner lining of blood vessels, pivotal in vascular homeostasis and integrity. However, these cells are perpetually subjected to a myriad of mechanical, chemical, and biological stresses that can compromise their plasma membranes. A sophisticated repair system involving key molecules, such as calcium, annexins, dysferlin, and MG53, is essential for maintaining endothelial viability. These components orchestrate complex mechanisms, including exocytosis and endocytosis, to repair membrane disruptions. Dysfunctions in this repair machinery, often exacerbated by aging, are linked to endothelial cell death, subsequently contributing to the onset of atherosclerosis and the progression of cardiovascular diseases (CVD) and stroke, major causes of mortality in the United States. Thus, identifying the core machinery for endothelial cell membrane repair is critically important for understanding the pathogenesis of CVD and stroke and developing novel therapeutic strategies for combating CVD and stroke. This review summarizes the recent advances in understanding the mechanisms of endothelial cell membrane repair. The future directions of this research area are also highlighted.

The structure of existing activated models is inherently deficient in reflecting the major role of the membrane filtration. This study developed and proposed a novel model, MASM, for the membrane activated process. The effective filtration size imposed by the membrane module, entrapping larger size particles was adopted as the basis of the proposed model. The model defined a modified COD fractionation, accounting for the captured COD fractions as additional model components and utilizing related mass balance relationships. It was implemented for testing the fate of soluble hydrolysable COD and system performance of super-fast membrane activated sludge based on real data for the characterization and process kinetics of domestic sewage and denim processing effluents. Model evaluation was carried for parallel systems with gravity settling and membrane filtration operated at a sludge age range of 0.5-2.0 d. Results reflected significantly better performance of super-fast membrane activated sludge system for both wastewaters, underlining that it was crucially important to account for the captured COD fractions to provide an accurate evaluation of system behavior and effluent quality. This should also be identified as the major shortcoming of the ASM models for evaluating and predicting system performance of activated sludge configurations with membrane separation.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

Mode locked pulse generation has been reported using both active and passive mode locking schemes. Active mode locking technique has been proven to be an effective way to generate high-repetition-rate pulses by incorporating a modulator inside the laser cavity. Compared to actively mode locked lasers, passively mode locked lasers can generate pulse train at ultrashort pulse width but with relatively lower repetition rate. Thus, it is a brilliant idea to build a hybrid mode locked system combining both active and passive mode lockers. In this review, several hybrid mode locked fiber ring laser systems are discussed and summarized. Hybrid mode locking is a promising method to generate high speed ultrashort optical pulses for fiber-optic telecommunication system.

Extracorporeal membrane oxygenation (ECMO) is used for the management of severe respiratory and cardiac failure, as well as bridge to definite treatment or transplantation. ECMO associated coagulopathy (EAC) is a frequent complication leading to high rates of thrombosis or severe haemorrhage, contributing to morbidity and mortality of patients. Understanding the pathophysiology of EAC is substantial for effectively managing patients on ECMO. We analyse the underlying mechanism of EAC and discuss the monitoring of coagulation profile, combining the viscoelastic point of care assays with the conventional coagulation laboratory tests.

The aim of the study was to assess the effect of the addition of inulin and the replacement of part of inulin with apple fiber on the physicochemical and organoleptic properties. Moreover, the survival of Bifidobacterium animalis ssp. Lactis Bb-12 and Lactobacillus rhamnosus was studied in sheep milk ice cream. There was no effect of apple fiber and the type of bacteria on the number of bacteria of the probiotics after fermentation. As a result of freezing, mixture containing Bifidobacterium animalis ssp. Lactis Bb-12, there was a significant reduction in the bacterial from 0.39 log cfu g −1 to 0.46 log cfu g −1. In all ice cream on the 21st day of storage, it exceeded 10 log cfu g –1, which means that the ice cream retained the status of probiotic products. The Lactobacillus rhamnosus ice cream showed a lower yellow colour compared to the Bifidobacterium Bb-12 ice cream. The overrun of sheep's milk ice cream was within a range from 78.50% to 80.41%. The appearance of sheep's milk ice cream is influenced considerably by the addition of fiber and the type of bacteria and the interaction between the type of bacteria and the addition of fiber and storage time and fiber.

Blending lignin as the second most abundant polymer in nature with nanostructured compounds such as dendritic polymers will not only add value to lignin, but also increase its application in various fields. In this study, softwood Kraft lignin/polyamidoamine dendritic polymer (PAMAM) blends were fabricated by solution electrospinning method to produce bead-free nanofiber mats. The mats were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), zeta potential, and thermogravimetry analysis (TGA). The chemical intermolecular interactions between lignin functional groups and abundant amino groups in PAMAM were investigated by FTIR and viscosity measurement. These interactions enhanced the mechanical and thermal characteristics of lignin/PAMAM mats, providing further potential applications at industry level.

The damage caused by global warming is rapidly increasing, and its adverse effects become more evident with each passing day. Although it is known that the use of alternative binder materials in concrete would decrease this negative effect, reluctance to new composites continues. Waste use plays a vital role in sustainability studies. In this study, pure cement paste was prepared and enriched with carbon fiber. This study investigated the wide range of volume fraction of carbon fiber in cement-based composites. Two different industrial wastes, marble dust, and bottom ash were chosen and mixed with cement and four different (0.3%, 0.75%, 1.5%, and 2.5%) carbon fiber volume fractions. Based on physical, mechanical, and durability tests at 7, 28, and 56-days of curing, the composites were resistant to sulfate and seawater attack. The 0.75% carbon fiber addition seems to be an optimum volume percentage beyond which both physical and mechanical properties were adversely affected. The composites with 0.75% carbon fiber have reached 48.4 MPa and 47.2 MPa at 56-days of curing for marble dust and bottom ash mixture groups, respectively.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

The calculation of the global shear capacity of steel-concrete composite downstand cellular beams with precast hollow-core units is important as it affects the span to depth ratios and the amount of material used, hence affects the embodied CO2 calculation when designers are deciding on the floor grids. This paper presents a reliable tool that can be used by designers to alter and optimise grip options during the preliminary design stages, without the need to run onerous calculations. The global shear capacity prediction formula is developed using five machine learning models. First, a finite element model database is developed. The influence of the opening diameter, web opening spacing, tee-section height, concrete topping thickness, the interaction degree, and the number of shear studs above the web opening are investigated. Reliability analysis is conducted to assess the design method and propose new partial safety factors. The Catboost Regressor algorithm presented better accuracy compared to the other algorithms. An equation to predict the shear capacity of composite cellular beams with hollow-core units is proposed by Gene Expression Programming. In general, the partial safety factor for resistance, according to the reliability analysis, varied between 1.25 and 1.26.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

Ras is the most frequently mutated oncogene and recent drug development efforts have spurred significant new research interest. Here we will review progress toward understanding how Ras functions in nanoscale, proteo-lipid signaling complexes on the plasma membrane, called nanocluster. We will discuss how G-domain reorientation is plausibly linked to Ras-nanoclustering and -dimerization. We will then look at how these mechanistic features could cooperate in the engagement and activation of RAF by Ras. Moreover, we will show how this structural information can be integrated with microscopy data that provide nanoscale resolution in cell biological experiments. Synthesizing the available data, we propose to distinguish between two types of Ras nanoclusters, an active, immobile RAF-dependent type and an inactive/ neutral membrane anchor-dependent. We conclude that it is possible that Ras reorientation enables dynamic Ras dimerization, while the whole Ras/ RAF complex transits into an active state. These transient di/oligomer interfaces of Ras may be amenable to pharmacological intervention. We close by highlighting a number of open questions including, whether all effectors form active nanoclusters and whether there is an isoform specific composition of Ras nanocluster.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

A number of third order nonlinear processes can occur in single-mode fibres and an understanding of such phenomena is almost a prerequisite for actual lightwave-system designers. In this paper we review the main limitations imposed by several nonlinear effects, namely the self- and cross-phase modulation, four-wave mixing, stimulated Raman scattering and stimulated Brillouin scattering, on the performance of optical fiber communication systems.

The optical properties of the Nafion polymer membrane containing colloidal CdSe/CdS/ZnS nanocrystals embedded by diffusion have been studied. The CdSe/CdS/ZnS nanocrystals have a core/shell/shell appearance. A toluene solution was used to provide mobility of the active sul-fone groups of the Nafion membrane and to embed the nanocrystals inside the membrane. The kinetics of the process of nanocrystal embedding into the membrane matrix was studied using luminescence analysis, absorption spectroscopy and laser emission spectroscopy techniques. The diffusion of colloidal CdSe/CdS/ZnS nanocrystals into the Nafion proton exchange membrane resulted in a new molecular complex «Nafion-colloidal CdSe/CdS/ZnS nanocrystals». The pres-ence of new luminescence centers based on CdSe/CdS/ZnS nanocrystals in the membrane was registered using laser emission spectroscopy. Colloidal nanocrystals located in the Nafion ma-trix represent an analogue of a luminescent transducer. The lines contained in the luminescence spectrum of the membrane, which has been in solution with colloidal nanocrystals for a long time, registered upon its drying, show the kinetics of the formation of the molecular complex «Nafion membrane - nanocrystals». The luminescence spectrum of the membrane with nano-crystals contains additional intensity maxima that do not coincide with the spectral lines of the solvent and Nafion membrane. The intensity of the luminescence spectrum of the membrane with embedded nanocrystals is higher than the intensity of the secondary emission peak of the initial nanocrystals, which is important for the practical use of the complex «Nafion-colloidal nanocrystals» in optical systems.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.