This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

In this study, a matched-mode autoregressive source depth estimation method (MMAR) based on autoregressive (AR) wavenumber estimation is proposed for a moving source in shallow water waveguides. The signal original frequency and the environmental parameters, namely, the sound speed profile and bottom properties are known as a prior knowledge. The mode wavenumbers are estimated by the AR modal wavenumber spectrum. On the basis of the mode wavenumber estimation, the mode amplitudes can be estimated by the wavenumber spectrum that is obtained by generalized Hankel transform. The source depth estimation is determined by the peak of source depth function wherein the data mode best matches the replica mode that is calculated using a propagation model. Compared with other methods of moving source depth estimation, the proposed method exhibits a better performance in source depth estimation under low signal-to-noise ratio or the small range span. The selection of horizontal line array depth is illustrated by simulation and normal mode theory in details.

Building defects are very prevalent and contribute significantly to a building's economic value. There are numerous information sources on building defects that have a lot potential for learning more about building defects. This study aimed to identify the information sources used in previous building defect studies and to identify the motivation for carrying out such studies. To fulfil this aim a scoping study was carried out. The information sources identified included insurance companies, private databases, questionnaire surveys, lawsuits, building surveys, client complaint forms, and maintenance reports. This study found that insurance company and client complaint forms include the largest collection of real building defect cases, but such databases may lack detailed descriptions of the causes of the defects. The main purposes of building defects studies identified here included design challenges, identification of defects, building maintenance management, quality management, systematization in data collection, providing an overview of typical defects, and classifying defects. Identification was found to be the most common purpose, indicating that the industry wants to learn more. This study identified research gaps in the climate perspective in relation to building defects. Most of the studies focused on the economical perspective, and none focused on the carbon footprint perspective.

Agrivoltaic agrotunnels are currently designed for high density grow walls that are not amenable to bush berries or root crops. Commercial grow bins provide deeper substrates for produce with more root systems but have high costs per unit growing area. To overcome the economic limitations of grow bins, this study applies the distributed manufacturing open-source design paradigm to develop four designs for low-cost open source structures. The designs target root vegetables and bush fruit specifically to be adopted by remote communities with limited or no outdoor growing environment to offset the market price for imported fresh produce. The indoor growing designs provide the necessary structure for supporting grow light and grow bins and enabled the transplanted berry plants to flower and produced fruits. They provide a comparable amount (110L) or more of grow volume from 106 to 192 L. The water reservoir volume for the commercial system (62 L) and grow area (0.5 m³) is surpassed by all new designs that range from 64 to 192 L and 0.51 to 0.76 m³, respectively. These superior properties are possible with material costs for all four designs that save more than 90% of the economic cost of the commercial systems.

This paper provides the straight proof for the Riemann Hypothesis.The proof has been formulated with the modified version of Riemann Xi function ξ(s) , that shows the relationship with upper incomplete gamma function.

Hypertension is a global public health challenge, with a high prevalence across various regions and significant implications for cardiovascular risk. This article reviews the effectiveness of herbal medicine as a potential therapeutic approach for hypertension, offering an alternative or complementary solution to conventional pharmacological treatments. It highlights several natural agents that have demonstrated efficacy in lowering systolic blood pressure (SBP) in clinical and meta-analytical studies. The methodology involved a systematic review of articles that discuss herbal therapeutics for hypertension, focusing on their efficacy compared to placebo and standard treatments. The findings suggest that certain nutraceuticals, such as garlic, hawthorn, and CoQ10, can significantly reduce SBP, presenting a viable option for managing hypertension. This review underscores the need for further research to validate these findings and optimize herbal treatment strategies, potentially expanding the use of these natural products in clinical practice. The article aims to increase awareness among medical professionals and patients about the benefits and applications of herbal medicines in treating hypertension.

Reducing and time-shifting household energy demand is important for a sustainable transition of energy systems, and dynamic electricity pricing, like real-time pricing (RTP), is a popular instrument to incite households to change energy demand. However, the effect of such products relies on the assumption that dynamic price signals incorporate into everyday routines and rhythms. This paper investigates the flexibility of households’ everyday routines and rhythms. The study provides three insights based on 11 Danish household visits and interviews with electricity customers who are new to RTP. First, the interviews indicated confusion over terminology for dynamic pricing products and low interest in flexible energy demand. Second, everyday practices (already) appeared flexible but for other reasons than energy demand flexibility. Third, energy habits were important for providing meaning to everyday practices. In addition, the study shows that energy flexibility is not just about energy demand, but rather about all the other activities that form routines and rhythms in everyday life. We suggest 1) designing products that reflect ‘natural’ or ‘societal’ daily rhythms, 2) focusing on the engaged households, and 3) being aware that for some households, changes in pricing, including new payment schemes, might put extra pressure on already harried everyday routines.

In this paper, a small wind power generator is proposed with a new straight shape stator and rotor. The advantages of the proposed structure are introduced through a comparison between the basic and the proposed models. By comparing the pole slot combination of the proposed generator, the combination with optimal cogging torque characteristics was selected. The electromagnetic characteristics of proposed shape are analyzed for design variables using a finite element analysis (FEA) of ANSYS Maxwell. The final model of the proposed structure is designed by considering cogging torque and the generator electromagnetic characteristics. The electromagnetic and structural simulations of the final model are performed to satisfy the required performance of generator and mechanical safety. To verify the FEA results of the final model, a prototype is manufactured, experimented, and compared with the FEA results.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Context. During the COVID-19 pandemic, patient care was mainly organised around the hospital. Pre-hospital care has, to our knowledge, never been evaluated. Objective: To evaluate the impact of pre-hospital pathways on hospitalisation during the last part of the pandemic. Design. This was a monocentric retrospective analysis of prospectively collected medical records. Data from patients admitted to our institute between 1 February and 7 March 2022 were analysed. Main Outcome Measure(s): The primary outcomes were defined as the number of hospitalisations, resuscitations, and deaths at the time of interview and in the subsequent 30 days. The main explanatory variables were times from onset of symptoms to care, age, gender, News2 score, comorbidities, and pre-hospital pathways and their duration. Results: Three pre-hospital pathways have been identified: a pathway in which the patient consults a general practitioner for a test (PHP1); a pathway in which the patient consulted for care (PHP2); and no pre-hospital pathway and direct admission to hospital (PHP3). Factors independently associated with outcome (hospitalisation) were being male (OR 95% CI; 2.21 [1.01–4.84], p=0,04), News2 score (OR 95% CI; 2.04 [1.65–2.51], p<0.001), obesity (OR 95% CI; 3.45 [1.48–8.09], p=0.005), D-dimers > 0.5 µg/ml (OR 95% CI; 3.45 [1.47–8.12], p=0.005), prolonged time from symptoms to hospital care (PHP duration) (OR 95% CI; 1.07 [1.01–1.14], p=0.03). All things being equal, patients with a “PHP2” pre-hospital pathway had a higher probability of hospitalisation compared to those with a “PHP3” pre-hospital pathway (OR 95% CI; 4.31 [1.48–12.55], p=0.007). Conclusions. Along with recognised risk factors such as gender, News 2 score, and obesity, the patient’s pre-hospital pathway is an important risk factor associated with hospitalisation.

High hepcidin is linked to low-grade inflammation and lower iron levels. The consequence of testosterone replacement therapy (TRT) on inflammation and risk of cardiovascular disease (CVD) is undetermined. We investigate the effect of TRT on the inflammatory cardiovascular risk markers hepcidin-iron, fibroblast growth factor 23 (FGF23)-phosphate-klotho, and calprotectin pathways. Methods: A randomized, placebo-controlled, double-blinded study at an academic tertiary-care medical center. Interventions were testosterone gel (TRT, n=20) or placebo gel (n=19) for 24 weeks. We included 39 men (50─70 years) with type 2 diabetes (T2D) on metformin monotherapy with bioavailable testosterone levels <7.3 nmol/L. Body composition was assessed by DXA- and MRI-scans; main study outcomes were serum hepcidin-iron, FGF23, phosphate, klotho, and calprotectin. Results: Hepcidin levels decreased during TRT (β=-9.5 ng/mL, P<0.001), lean body mass (β=1.9 kg, P=0.001) increased, and total fat mass (β=-1.3 kg, P=0.009) decreased compared to placebo. Delta hepcidin was not associated with changes in lean body mass or fat mass. Iron and the pathways of FGF23-phosphate-klotho and calprotectin were unchanged during TRT. Conclusions: During TRT, the reduction in hepcidin was not associated with circulating iron levels, lean body mass, or fat mass; these findings suggested a direct anti-inflammatory effect of TRT and no indirect effect mediated through these factors.

This research explores the application of Support Vector Machine (SVM) and Digital Surface Models (DSM) derived from Unmanned Aerial Vehicle (UAV) data for a vertical-horizontal classification of mangrove ecosystems in Tongke-tongke and Samataring Village. The study focuses on integrating high-resolution DSM subtracted from Digital Terrain Models (DTM) to classify mangrove vegetation into sixteen distinct vertical-horizontal classes based on vegetation type and elevation. The analysis revealed that older mangroves, particularly those within the 25-35 meters elevation range, dominate the landscape, accounting for 43.40% of the total classified area. This dominance suggests a mature and ecologically stable mangrove ecosystem, which is crucial for biodiversity conservation and carbon storage. The study demonstrates the effectiveness of SVM and UAV technologies in providing detailed and accurate ecological assessments of mangrove forests. The classification results contribute valuable insights into the structural diversity and health of mangrove ecosystems, facilitating targeted conservation and management strategies. Additionally, the research highlights the utility of advanced remote sensing and machine learning techniques in enhancing the precision of environmental monitoring and the assessment of carbon sequestration capabilities within mangrove ecosystems. The findings underscore the potential of UAV-based remote sensing for ecological studies, offering a replicable method for similar assessments in other regions, thereby supporting global environmental management and climate action initiatives.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

Bare slope instability is a prevalent concern. The root system of, herbaceous vegetation enhances the shear strength of shallow–slope soil. Indoor experiments were conducted on rootless undisturbed soil (RUS) and undisturbed soil with a root system (USRS) using a triaxial compression apparatus to analyze the slope stability of composite soil with a Tagetes erecta root system. Significance tests and correlation analysis of the factors affecting shear performance were conducted using R software. The slope reinforcement, effect by the plant root system was simulated under 24 working conditions using the MIDAS finite element method. The results revealed the influence of the–root content (RC), moisture content (MC), and stress on the shear strength of USRS, the contribution degree, and the variables’ influences on slope stability. Both RUS and USRS exhibited strain hardening during shearing. The internal friction angle (φ) and cohesion (c) of USRS were negatively and positively correlated with the RC and MC (root burial depth), respectively, and a good fit was obtained for the relationship. The maximum deviatoric stress during shear failure was 1.29 times higher for USRS than for RUS. The RC (root depth) was positively correlated with the slope safety coefficient and the slope of the line under different working conditions, whereas the slope gradient was negatively correlated with the slope safety coefficient. The reinforcement effect by the root system resulted in a 13.2% increase in the safety coefficient and improved stability of slopes with a gradient larger than 1.5%. This article investigated the mechanism of the root–soil system and, the effects of different influencing factors on the shear strength of the soil, and slope stability. The findings provide new insights into shallow slope stability in practical slope protection projects.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

This study uses simulation and experimental methodologies to explore the efficacy of bi-sectional horizontal kinetic shading systems (KSS) featuring horizontal fins in enhancing daylight comfort across various climates. Given the increasing energy demands and shifting climatic patterns, optimizing daylight levels while minimizing solar heat gain is vital. The paper introduces a bespoke horizontal bi-sectional KSS, simulated in three distinct climates—Wroclaw, Tehran, and Bangkok—using Climate Based Daylight Modelling methods with Ladybug and Honeybee tools in Rhino software. The study employs standard daylight metrics such as Useful Daylight Illuminance (UDI) and Daylight Glare Probability (DGP), along with custom metrics designed to capture the specific dynamics of the bi-sectional KSS. Initial simulations indicated that the KSS significantly improved daylight distribution and uniformity, reducing glare and over-illumination risks by av. 42.34%. Including KSS switching schedules, which are seldom detailed in similar research, enhances the reproducibility and understanding of findings. Subsequently, a physical reduced-scale mock-up of the bi-sectional KSS was tested under real-weather conditions in Wroclaw (lat. 51° N) during June-July 2024. The mock-up utilized two chambers: one equipped with the prototype of bi-sectional KSS and the second without any protection. The operation of fins was guided by two stepper motors controlled by a Python script running on a Raspberry Pi 3 minicomputer. The control chamber served to benchmark the bi-sectional KSS's efficiency by providing results that would be expected if no shading system were installed. The experimental outcomes supported the simulations, demonstrating the KSS's robustness in reducing high illuminance levels to the target comfort level, thus enhancing indoor visual comfort. The values below 3,000 lux were maintained for 68% of the time. However, it must be explicitly stated that during the June-July 2024 heat waves, the illuminance levels inside the test room momentarily exceeded the comfort threshold of 3,000 lux, reaching up to 4,674 lux. Through quantitative and qualitative analyses, the paper advocates for the broader application and further development of KSS as a climate-responsive shading system in diverse architectural contexts.

Objective: We reviewed the available literature on patients undergoing minimally invasive mitral valve surgery (MIMVS) with either transthoracic clamping (TTC) or endoaortic balloon occlusion (EABO). Methods: Original research studies that evaluated the perioperative outcomes of TTC versus EABO group were identified, from 2000 to 2024. The incidence of all-cause mortality, cerebrovascular accidents (CVA), and aortic dissections were the primary endpoints. The cardiopulmonary bypass (CPB), cross-clamp, and ventilation time, along with the incidence of conversion to sternotomy, re-exploration, new-onset atrial fibrillation (AF), postoperative acute kidney injury (AKI), ICU stay, and LOS were the secondary endpoints. Subgroup analyses were performed regarding EABO cannulation approach (femoral and aortic) and MIMVS approach (video-assisted and robotic-assisted). Sensitivity analyses were performed including risk-adjusted populations and with the leave-one-out method. Results: Sixteen studies were included in the qualitative and quantitative synthesis. After pooling data from 6,335 patients, both groups demonstrated similar outcomes on all primary and secondary endpoints in the non-adjusted and adjusted total cohort analyses. These outcomes were further validated by the leave-one-out sensitivity analysis. In addition, the aortic cannulation EABO was associated with lower cross-clamp time, followed by TTC and femoral cannulation EABO approach. Furthermore, in the video-assisted subgroup analysis, the EABO approach was associated with a higher incidence of CVA, conversion to sternotomy, and longer ICU stay compared to the TTC group. Conclusions: The present meta-analysis indicates that both aortic occlusion techniques are safe and feasible in the context of MIMVS. A future well-designed Randomized-Control Trial should further validate the current outcomes.

Objectives: In recent years, ear endoscopy has gradually become an important tool in ear surgery. This study further explored its application in ear surgery, to establish a surgical approach for semicircular canal obstruction (SOC) via the ear canal to control vertigo in Meniere's disease. Methods: With the approval of the ethics committee, recruitment started in June 2019. ​Four patients with Meniere's disease who had been treated conservatively for more than six months received SCO via an external ear canal approach under otoendoscopy and were followed for two years after surgery to assess the safety and efficacy of the procedure. Results The control of vertigo after the operation was satisfactory (100%), and the frequency and degree of vertigo were significantly improved. Tinnitus improved in 1 case (25%) and did not progress in the other 3 cases. Hearing loss did not progress in all patients. Postoperative walking instability occurred in 1 patient (25%), and there were no obvious complications. All patients reported significant improvements in their quality of life. Conclusions: SCO via the external auditory canal approach is safe, effective, easy to accept, and an alternative to conservative treatment of Meniere's disease with no actual hearing for more than 6 months.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

The systematic sampling is used as a method to get the quantitative results from the tissues and the radiological images. Systematic sampling on real line (R) is a very attractive method within which the biomedical imaging is consulted by the practitioners. For the systematic sampling on R, the measurement function (MF) is occurred by slicing the three-dimensional object equidistant systematically. The currently used covariogram model in variance approximation proposed by [28,29] is tested for the different measurement functions in a class to see the performance on the variance estimation of systematically sampled R. This study is an extension of [17], and an exact calculation method is proposed to calculate the constant λ(q,N) of confidence interval in the systematic sampling. The exact value of constant λ(q,N) is examined for the different measurement functions as well. As a result, it is observed from the simulation that the proposed MF should be used to check the performances of the variance approximation and the constant λ(q,N). Synthetic data can support the results of real data.

Enhancing spectral efficiency, especially in Non-line-of-Sight environments, is emerging as a pivotal necessity when dealing with the evolving landscape of 5G networks and beyond, sur-passing the capabilities of previous 4G systems to achieve a high information rate combined with minimal interference. Contrary to depending on the traditional Orthogonal Multiple Access (OMA) systems to tackle the issues caused by Non-line-of-Sight (NLoS) environments, advanced wireless networks are focusing on adopting innovative models such as Non-Orthogonal Multiple Access (NOMA), MIMO, IRS technology, etc. In this paper, we present technologies that can be integrated with NOMA to enhance communication reliability in environments that suffer from issues such as limited coverage and lower spectral efficiency mainly caused by huge obstacles. Our exploration includes the fundamental concepts of Cooperative NOMA (C-NOMA), Multiple Input Multiple Output (MIMO), Intelligent Reflective Surfaces (IRS), Unmanned Aerial Vehicles (UAVs), and Energy Harvesting (HV), which adds a layer of sophistication, promising not only improved connectivity but also contributing to a more reliable and environmentally friendly data trans-mission landscape.

Linear regression is a basic tool in mobile robotics, since it enables accurate estimation of straight lines from range-bearing scans or in digital images, which is a prerequisite for reliable data association and sensor fusing in the context of feature-based SLAM. This paper discusses, extends and compares existing algorithms for line fitting applicable also in case of strong covariances between the coordinates at each single data point, which must not be neglected if range-bearing sensors are used. Besides, particularly the determination of the covariance matrix is considered, which is required for stochastic modeling. The main contribution is a new error model of straight lines in closed form for calculating fast and reliably the covariance matrix dependent on just a few comprehensible and easily obtainable parameters. The model can be applied widely in any case when a line is fitted from a number of distinct points also without a-priori knowledge of the specific measurement noise. By means of extensive simulations the performance and robustness of the new model in comparison to existing approaches is shown.

Keywords: Linear differential arrays; beam steering; frequency-invariant beamforming.

Spontaneous tumours in higher plants can develop depending on plant genotype without any pathogen invasion. Spontaneous tumour formation on the taproots is consistently observed in certain inbred lines of radish (Raphanus sativus var. radicula Pers.). In this work, we have sequenced the genomes of two closely related radish inbred lines that differ in their ability to spontaneously form tumours. We have identified numerous single nucleotide variants (amino acid substitutions, insertions or deletions) that are likely to be associated with the spontaneous tumour formation. Furthermore, we performed the identification of CLE and WOX genes the genomic sequences of the radish inbred lines and, as a result, identified two unique radish CLE genes which probably encode proteins with multiple CLE domains. The results obtained provide a basis for investigating the mechanisms of plant tumour formation and also for future genetic and genomic studies of radish.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Elizabethkingia anophelis is an opportunistic pathogen causing lifethreatening infections in humans, particularly in immunocompromised patients, neonates and elderly. Infections caused by this species are exceptionally challenging to treat due to its multiresistance to antimicrobials. We report a case of central line-associated bloodstream infection by E. anophelis in a 2.5-year-old girl with acute lymphoblastic leukemia successfully treated with a combination of piperacillin/tazobactam and amikacin. The literature was also reviewed on paediatric infections caused by E. anophelis. Accurate identification with MALDI-TOF, or using molecular techniques, is crucial because of varying susceptibilities among species. Early, accurate diagnosis and prompt effective treatment optimize outcomes.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

Aim at a better understanding of the flow field around a fully appended Joubert BB2 submarine model and complementing the experimental investigations of the wake of the hydroplanes and sail, the Large eddy simulation (LES) with the dynamic Smagorinsky model is conducted. Three sets of grids with a maximum grid number of up to 228 million are designed, to perform the LES simulation for the Joubert BB2 at 10° yaw conditions, with a freestream Reynolds (Re) number based on the local freestream velocity and the hull length of ReL=2.2×107. And comparison of the wake of the cruciform appendage is made with experiments, to verify the computational accuracy and examine the influence of the spatial resolution. A satisfactory result shows more favorable agreement with experimental measurements as the improvement of spatial resolution, with the relative error of the vortice centers well within 7.2% in the most refined grid arrangement. And under this grid arrangement, the evolution characteristics of three co-rotating vortices originating from the cruciform appendage are further described in detail at straight ahead and 10° yaw conditions.

Metal-catalyzed lipid oxidation is a major factor in food waste, as it reduces shelf life. Addressing this issue, our study investigates the potential of hydrolysates derived from potato protein, a by-product of potato starch production, as metal chelating antioxidants. Through sequential enzymatic hydrolysis using Alcalase or Trypsin combined with Flavourzyme, we produced various hydrolysates, which were then fractionated via ultrafiltration. Using a combination of peptidomics and bioinformatics, we predicted the presence of metal-chelating and free radical scavenging peptides across all hydrolysate fractions, with a trend indicating a higher content of antioxidant peptides in lower molecular weight fractions. To validate these predictions, we utilized Surface Plasmon Resonance (SPR) and a 9-day emulsion storage experiment. While SPR demonstrated potential in identifying antioxidant activity, it faced challenges in differentiating between hydrolysate fractions due to significant standard errors. In the storage experiment, all hydrolysates showed lipid oxidation inhibition, though not as effectively as EDTA. Remarkably, one fraction (AF13) was not significantly different (p < 0.05) from EDTA in suppressing hexanal formation. These results highlight SPR and peptidomics/bioinformatics as promising yet limited methods for antioxidant screening. Importantly, this study reveals the potential of potato protein hydrolysates as antioxidants in food products, warranting further research.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

Previous control methods developed by our research team cannot satisfy the high-accuracy requirements of unmanned surface vessel (USV) path-tracking during bathymetric mapping because of the excessive overshoot and slow convergence speed. For this reason, this study developed an adaptive fuzzy integral-derivative line-of-sight (AFIDLOS) guidance law for USV path-tracking control. Integral and derivative terms were added to counteract the effect of the sideslip angle, with which the USV could be quickly guided to converge to the planned path for bathymetric mapping. To obtain a high-accuracy of the look-ahead distance, a fuzzy control method was proposed. The proposed method was verified using simulations and outdoor experiments. The results demonstrate that the AFIDLOS guidance law can reduce the overshoot by 79.85%, shorten the settling time by 55.32% in simulation experiments, and reduce the average cross-track error by 10.91%, and can ensure a 30% overlap of neighboring strips of bathymetric LiDAR outdoor mapping when compared with the traditional method.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

Semantic rules link purely theoretical terms like “price” and “electron” to things we can measure. Without them, theories cannot be tested empirically. When inappropriate, they produce false rejections. Economists routinely ignore semantic rules. Empirical journal articles essentially never mention them. More to the point, the conventional tests that reject the Law of One Price and Purchasing Power Parity never consider them. As a result, those rejections are unwarranted because such tests use inappropriate semantic rules. Both theories should be restored to not rejected and then retested using the more appropriate semantic rules described here. By using appropriate semantic rules, this paper is able to combine Covered Interest Parity and Purchasing Power Parity into a single theory that links auction markets for financial assets and commodities to auction markets for exchange rates. Using appropriate semantic rules for both theories also explains several puzzles in open economy macroeconomics and opens up broad new vistas for research.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

This paper proposes a definition of fractional line integral, generalising the concept of fractional definite integral. The proposal replicates the properties of the classic definite integral, namely the fundamental theorem of integral calculus. It is based on the concept of fractional anti-derivative used to generalise the Barrow formula. To define the fractional line integrals the Gr\"unwald-Letnikov and Liouville directional derivatives are introduced and their properties described. The integral is defined first for broken line paths and afterwards to any regular curve

The paper presents the possibility of using KINECT v2 module to control an industrial robot by means of gestures and voice commands. It describes elements of creating software for off-line and on-line robot control. The application for KINECT module was developed in C# language in Visual Studio environment, while the industrial robot control program was developed in RAPID language in RobotStudio environment. The development of a two-threaded application in RAPID language allowed to separate two independent tasks for the IRB120 robot. The main task of the robot is performed in thread no. 1 (responsible for movement). Simultaneously working thread no. 2 ensures continuous communication with the KINECT system and provides information about the gesture and voice commands in real time without any interference in thread no. 1. The applied solution allows the robot to work in industrial conditions without negative impact of communication task on the time of robot’s work cycles. Thanks to the development of a digital twin of the real robot station, tests of proper application functioning in off-line mode (without using a real robot) were conducted. Obtained results were verified online (on the real test station). Tests of correctness of gesture recognition were carried out, the robot recognized all programmed gestures. Another test carried out was the recognition and execution of voice commands. A difference in the time of task completion between the actual and virtual station was noticed - the average difference was 0.67 s. The last test carried out was to examine the impact of interference on the recognition of voice commands. With a 10dB difference between the command and noise, the recognition of voice commands was equal to 91.43%. The developed computer programs have a modular structure, which enables easy adaptation to process requirements.

Biomimetic materials are substances that replicate natural structures. There are several methods for producing such materials with highly developed surfaces from a wide range of polymers, but electrospinning is of particular interest due to its simplicity of implementation and the ability to modify the produced fibrous materials resembling structures found in living organisms. This study explores new biomimetic materials based on polyhydroxyalkanoates, specifically poly-3-hydroxybutyrate, modified with chlorophyll derivatives. The research investigates the impact of chlorophyll derivatives on the morphology, supramolecular structure, and key properties of nonwoven materials. The obtained results are of interest for the development of new biomimetic environmentally friendly materials for biomedicine with special properties.

The inter-tip times (ITTs) of tipping-bucket rain gauges potentially provide the highest-resolution intensity data that can be acquired from this type of gauge. At an intensity of 100 mm h-1, a typical gauge with a sensitivity of 0.2 mm of rainfall would be expected to tip every 7.2 seconds. However, TBRGs are often equipped with syphons, to reduce the dynamic calibration error that results from continued (and unmeasured) inflow to a bucket as it tips. This increases the accuracy of rainfall depth recording, but the time to fill and empty the syphon can reduce the ability of a TBRG to respond to (and for the ITTs to reflect) short-term intensity fluctuations. This ability is already limited by the discretisation arising from the filling and emptying of the buckets themselves. Laboratory tests with controlled water inflow rates were performed using two high-quality TBRGs, one a 'straight-through' design and the other syphon-equipped. These confirmed that at all intensities at which the syphon operates, a regular sequence of fixed-duration ITTs (such as the 7.2 s mentioned above) does not occur. Rather, the ITTs are perturbed by the syphon cycling. The gauges were also co-located in the field, and linked to carefully synchronised event data loggers. Data collected during several rainfall events revealed differences in the ITTs, and again confirm that the ITT sequence of a syphon-equipped TBRG exhibits artefacts related to syphon operation, that are not present in the 'straight-through' data. These artefacts can result in ITT differences of many minutes, depending on the rainfall intensity, and are problematic for the use of ITTs to estimate intensity. Peaks and troughs in the intensity profile also differed between the two gauges. It is recommended that in the application of TBRGs for studies where short-term intensity data are required, 'straight-through' gauges should be used, and syphon-equipped gauges avoided.

Acute exposure to cannabis has been associated with an array of cognitive alterations, increased risk for neuropsychiatric illness, and other neuropsychiatric sequelae including the emergence of acute psychotic symptoms. However, the brain alterations associating cannabis use and these behavioral and clinical phenotypes remains disputed. To this end, neuroimaging can be a powerful technique to non-invasively study the impact of cannabis exposure on brain structure and function in both humans and animal models. While chronic exposure studies provide insight into how use may be related to long-term outcomes, acute exposure may reveal interesting information regarding the immediate impact of use and abuse on brain circuits. Understanding these alterations could reveal the connection with symptom dimensions in neuropsychiatric disorders and, more specifically with psychosis. The purpose of the present review is to: 1) provide an update on the findings of pharmacological neuroimaging studies examining the effects of administered cannabinoids and 2) focus the discussion on studies that examine the sensitive window for the emergence of psychosis. Current literature indicates that cannabis exposure has varied effects on the brain, with the principal compounds in cannabis (delta-9-tetrahydrocannabinol and cannabidiol) altering activity across different brain regions. Importantly, we also discorvered critical gaps in the literature, particularly regarding sex-dependent responses and long-term effects of chronic exposure. Certain networks often characterized as dysregulated in psychosis, like the default mode network and limbic system, were also impacted by THC exposure, identifying areas of particular interest for future work investigating the potential relationship between the two.

Underwater natural gas pipelines constitute critical infrastructure for energy transportation. Any damage or leakage in these pipelines poses serious security risks, directly threatening marine and lake ecosystems and potentially causing operational issues and economic losses in the energy supply chain. Due to the difficulty in detecting deterioration over time and regularly inspecting these submerged pipelines by divers, the use of unmanned underwater vehicles (UUVs) becomes crucial in this field. In this study, an underwater pipeline tracking experiment was carried out by providing autonomous features to a remote-controlled unmanned underwater vehicle. During the tracking of the underwater pipeline, damages were identified, and the locations of these damages were determined. The navigation information of the underwater vehicle, including orientation in the x, y, z axes (roll, pitch, yaw) from a gyroscope integrated with magnetic compass, speed and position information in the three axes from an accelerometer, and the distance to the water surface from a pressure sensor, was integrated into the vehicle. Pre-tests determined the necessary pulse width modulation values for the thrusters of the vehicle, enabling autonomous operation by providing these values as input to the thruster motors. In this study, the vehicle moves in 3D was achived by the vertical thruster of the vehicle was activated to maintain a specific depth, and applying equal force to the vehicle’s right and left thrusters forward movement, while differential force induced deviation angles. In pool experiments, the unmanned underwater vehicle autonomously tracked the pipeline as intended, identifying damages on the pipeline using images captured by the vehicle's camera. The images for damage assessment were processed using a convolution neural network (CNN) algorithm, which is a deep learning method. The position of the damage relative to the vehicle was estimated from the pixel dimensions of the identified damage. The location of the damage relative to its starting point was obtained by combining these two positional pieces of information from the vehicle's navigation system. The all study was performed within the Python environment.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

Nonlinear nonparametric statistics (NNS) algorithm offers new tools for curve fitting. A relationship between k-means clustering and NNS regression points is explored with graphics showing a perfect fit in the limit. The goal of this paper is to demonstrate NNS as a form of unsupervised learning, and supply a proof of its limit condition. The procedural similarity NNS shares with vector quantization is also documented, along with identical outputs for NNS and a k nearest neighbours classification algorithm under a specific NNS setting. Fisher's iris data and artificial data are used. Even though a perfect fit should obviously be reserved for instances of high signal to noise ratios, NNS permits greater flexibility by offering a large spectrum of possible fits from linear to perfect.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Due to its potential harm to space payload, microwave corona breakdown of microstrip circuits has attracted much attention. This work describes an efficient way to suppress corona breakdown. Since corona breakdown threshold is determined by the highest electric field intensity at the surface of microstrip circuits, lacquer coating with thickness of tens of microns is sprayed on the top of microstrip circuits. The applied dielectric coating is used to move the discharge location away from circuit’s surface which is equivalent to reduce the highest electric field intensity on the in-terface of solid/air of the circuit and thus results into higher breakdown threshold. Two designs of classic coupled-line band-pass filter were used for verification. Corona experimental results at 2.5 GHz show that, in the interested low pressure range (100 to 4500 Pa), 5.3 dB improvement of mi-crowave corona breakdown threshold can be achieved for a filter with narrowest gap of 0.2 mm while its electrical performances like insertion loss, Q-factor are still acceptable. A threshold improvement prediction method is also presented and validated.

The incorporation of unmanned aircraft terminal operations into the scope of Detect and Avoid systems necessitates analysis of the safety performance of those systems—principally, an assessment of how well those systems prevent loss of well clear from and collision with other aircraft. This type of analysis has typically been conducted by Monte Carlo simulation with synthetic, statistically representative encounters between aircraft drawn from an appropriate encounter model. While existing encounter models include terminal airspace classes, none explicitly represents the structure expected while engaged in terminal operations, e.g., aircraft in a traffic pattern. The work described herein is an initial model of such operations, scoped at this time specifically for assessment of unmanned aircraft landings and encounters with other aircraft either landing or taking off. The model shares the Bayesian network foundation of other MIT Lincoln Laboratory encounter models but tailors those networks to address structured terminal operations, i.e., correlations between trajectories and the airfield and each other. This initial model release is intended to elicit feedback from the standards-writing community.

Multi-stage hydraulic fracturing with horizontal well technology has been widely used in shale oil reservoir. After hydraulic fracturing, hydraulic fractures and opened beddings are intertwined, which result in a complex fracture network. As well as the migration of multi-phase fluids during fracturing and soaking processes, which lead to complex flowback performance, and brings dif-ficulty to productivity evaluation and flowback strategies optimization. In this paper, taking the Daqing Gulong shale reservoir as an example, a numerical model for flowback period, which considered oil-water-gas three-phase flow and orthogonal fracture network has been established. The characteristics and influencing factors of flowback performance have been deeply studied, and the flowback modes of shale oil are reasonably optimized. Factors such as PTPG (pseu-do-threshold pressure gradient), opened bedding stress sensitivity, opened bedding permeability and matrix permeability have obvious effects on the flowback performance, resulting in signifi-cant variations in production peaks, high yield periods, and decline rates. In addition, three flowback modes are distinguished based on the rate at which the BHP (bottom hole pressure) drops. These correspond to three types of choke modes. Based on the result of numerical model, three flowback modes are optimized and the impacts of different flowback modes on shale oil flowback are clarified. This study is particularly important for understanding the performance of shale oil flowback and guiding the efficient exploitation of shale oil.

Our objective was to investigate the effects of topically applied neuropeptide Y (NPY) on ischemic wounds. Initially, the animal model for ischemic wound healing was validated using 16 male Sprague-Dawley albino rats. In the intervention study, an additional 28 rats were divided into three groups: NPY (0.025%), the positive control insulin-like growth factor-I (IGF-I, 0.0025%), and the hydrogel carrier alone (control). The hydrogel was selected due to its capacity to prolong NPY release (p &lt; 0.001), as demonstrated in a Franz diffusion cell. In the animals, an 8-mm full-thickness wound was made in a pedunculated dorsal ischemic skin flap. Wounds were then treated and assessed for 14 days, and procured at the end of the experiment for in situ hybridization analysis (RNAscope®) targeting NPY receptor Y2R and for meticulous histologic examination. Wound healing rates, i.e. the percentage wound area changes, did not show an increase with NPY (p = 0.938) but did with rhIGF-I (p = 0.039) compared to the control. Y2R mRNA was not detected in the wounds or adjacent skin but was identified in the rat brain (positive control). Light microscopic examination revealed trends of increased angiogenesis and enhanced inflammatory cell infiltration with NPY compared to control. An interesting secondary discovery was the presence of melanophages in the wounds. Our findings suggest the potential of NPY to enhance neovascularization under ischemic wound healing conditions, but further optimization of the carrier and dosage is necessary. The mechanism is elusive but likely involves NPY receptor subtypes other than Y2R.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Many spectroscopic diagnostics are routinely used as a technique to infer the plasma parameters from line emission spectra but their accuracy depends on the numerical model or code used for the fitting process. However, the validation of a line shape code requires some steps : comparison of the line shape code with other similar codes for some academic (simple) cases and then more complex ones, comparison of the fitting parameters obtained from the best fit of the experimental spectra with those obtained with other diagnostic techniques and/or comparison of the fitting parameters obtained by different codes to fit the same experimental data. Here we compare the profiles of the hydrogen Balmer β line in a helium plasma computed by six codes for a selected set of plasma parameters and we report on the plasma parameters inferred by each of them from the fitting to a number of experimental spectra measured in a helium corona discharge where the pressure was in the range 1- 5 bar.

Background: Cervical laminoplasty is a useful for treatment of cervical myelopathy. However, this procedure has limitations for kyphotic cervical alignments. We used the finite element (FE) analysis and investigated the biomechanical changes in an intact and laminoplasty models with lordosis, straight, and kyphosis cervical alignments. Methods: A three-dimensional FE model of the cervical spine (C2-C7) with ligaments was created from computed tomography. The model was modified with the following cobb angles and the C3-C6 laminoplasty was conducted; a) laminoplasty-lordotic model (LM-L; C2-C7 angle: -10°), b) laminoplasty-straight model (LM-S; C2-C7 angle: 0°), and c) laminoplasty-kyphotic model (LM-K; C2-C7 angle: 10°). A pure moment with a compressive follower load of 100N to represent the weight of the head/cranium and cervical muscle stabilization was applied to these models. The range of motion (ROM), annular stress, nucleus stress and facet forces were analyzed. Results: ROM of LM-K increased when compared to the other models except for flexion. The LM-K had the highest mobility with 49% increase in ROM observed under extension, compared to the intact model. In all motion except for flexion, LM-L models’ ROM decreased by more than 10%, and LM-S and LM-K models’ ROM increased by more than 10% at C2-C7 compared to the intact model. The annular stresses and nucleus stresses in LM-K were higher compared to the other models. The maximum increase in annular stresses was about 194% in LM-K compared to the intact model, observed at the C3-C4 segment. The facet contact forces were lowest in the LM-K, compared to the other models.Conclusions: Patients with a cervical kyphosis alignment are at a disadvantage of increased kyphosis compared to cases with lordosis or straight alignment and should be treated with caution.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Sports video analysis is an interesting and emerging field in the domain of computer vision. It has become a very popular subject among scholars all over the world in the last decade due to the need of automated classification of events such as offsides, in/out situations, goals and so on. The most important problem in sports video analysis is detection and tracking of ball and players. Extraction of court lines is also another important problem since it is necessary in the classification of aforementioned events. In this study, considering some of the previous work on the subject, we develop a method for tracking the ball and players in tennis videos where the camera position and orientation is supposed fixed.

We revisit a 2023 JAMA-published analysis of data from patients admitted for either COVID-19 or influenza to U.S. Veterans Administration (VA) hospitals in the fall/winter of 2022-2023. We note that baseline characteristics between the cohorts were similar, and the difference in vaccination rates was minimal, even after propensity score weighting. Had the vaccines been even minimally effective, significant differences in vaccination percentages would be expected. These findings call into question any efficacy claims associated with either the COVID-19 or influenza vaccines. Furthermore, the lack of efficacy of the influenza vaccines in reducing hospitalization is consistent with an earlier detailed study that found the same lack of efficacy, further validating the current result. This suggests that comparing vaccination rates between those hospitalized for different vaccine-preventable diseases can serve as a practical method for validating the vaccine efficacy claims of different vaccines.

Many people in the USA have lost their lives or become addicted to opioids via prescription opioids given for chronic pain. The chronic pain epidemic has emerged due to a convergence of factors, including the medicalization of pain as well as injuries happening in the workplace, in the home, or during recreation. Opioid prescriptions rose precipitously from the late 1990’s through to approximately 2020, and despite public awareness, still are increasing. This review examines literature on integrative approaches to chronic pain as delineated by pain type. The review is organized by the most common causes of chronic pain, and randomized controlled trials, meta-analyses and systematic reviews are extracted for each cause of chronic pain. Several promising interventions may alleviate chronic pain of some causes, and some interventions may work across pain causes. Lowering inflammation through dietary or lifestyle regimens may be a general way of reducing pain. Pain can be alleviated through several adjunctive and integrative treatment approaches, which may serve to lower the need for opioid medication.

We introduce and analyze conceptual approximations of the Boussinesq equation for horizontal unconfined aquifers during the pure drainage phase, without any reharge and zero-inflow conditions. We employ a variety of methods, which include wave solution, variable separation and series expansion to constract a new model and explore its behavior and performance against the Boussinesq equation and its exact (non-closed form) solution, at early and later times. The modeled non-linear forms are finally linearized concluding with explicit analytical expressions that incorporate most of the basic characteristics regarding the evolution of the water table and the outflow from the exact Boussinesq equation under different initial conditions. The endeavors of this work might be useful for theoretical and modeling purposes related to this problem.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

A thorough analysis and comparison of the fatty acid profiles of stipe and blade from Laminaria hyperborea, a kelp species found in the northern Atlantic, is presented. Lipids were extracted and fractionated into neutral lipids, free fatty acids and polar lipids, then derivatized to fatty acid methyl esters prior to GC-MS analysis. A total of 42 fatty acids were identified and quantified, including the n-3 fatty acids α-linolenic acid, stearidonic acid and eicosapentaenoic acid. An n-6/n-3 ratio of 0.8:1 was found in blade and 3.5:1 in stipe, respectively. The ratios vary between the lipid fractions within stipe and blade, with the lowest ratio in the polar lipid fraction of blade. The fatty acid amounts are higher in blade than in stipe, and the highest amounts of n-3 fatty acids are found within the neutral lipid fractions. The amounts of polyunsaturated fatty acids are 3.4 times higher in blade than stipe. This study highlights the compositional differences between the lipid fractions of stipe and blade from L. hyperborea. The amount of polyunsaturated fatty acids, compared to saturated- and monounsaturated fatty acids, as well as the n-6/n-3-ratio, is known to influence human health. In the pharmaceutical, food, and feed industries this can be of importance for production and sale of different health products. Additionally, lipids are today among the unused by products of alginate production, exploiting this material for commercial interest should give both economical and environmental benefits.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

Ants of the genus Solenopsis are important invasive pests in the world. Due to their high dispersion capacity, aggressive behavior and because they feed on various sources of vegetable and animal protein, these insects have caused serious damage to public health and agriculture. The control has usually been carried out through the use of organosynthetic insecticides. However, due to the ecological and environmental impacts caused by the use these products, more sustainable alternatives have been sought for their control. Faced with these problems and due to the scarcity of registered products for the control of these insects, we aimed with this study to synthesize and evaluate the anticidal potential of carvacrol derivatives. The lethal and sublethal effects caused by these derivatives were compared with the essential oil of Lippia gracilis (50.7% carvacrol) and with the base molecule — carvacrol. Carvacryl benzoate was the most toxic derivative to Solenopsis sp. with an LD50 of 3.20 g/ mg. This compound was about 2 and 7.6 times, more toxic than carvacrol at the doses needed to kill 50 and 90% of populations, respectively. The workers of Solenopsis sp. showed a rapid reduction in survival when exposed to carvacrol (LT50 = 8.43h) and carvacryl benzoate (LT50 = 8.87h). Insects treated with sublethal doses of the compounds did not show significant effects on self-cleaning, allogrooming and aggregation, with the exception of those treated with L. gracilis essential oil. The oil increased self-cleaning and reduced allogrooming and aggregation. Ants treated with carvacrol and carvacryl benzoate showed greater distance and speed when compared to the control. These compounds decreased meanders and angular velocity. When live workers were exposed to dead individuals at the LD90 of the compounds, carvacryl benzoate was the derivative that most reduced insects survival, due to horizontal transfer. These results show the potential of the carvacrol derivative — carvacryl benzoate — for the alternative management of ants of the genus Solenopsis sp.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

Our skin epidermis constitutes the most important innate defense barrier against all pathogens. Therefore, even if skin lesions are common due to infections, scarring, genetic disorders, and other diseases, skin integrity is crucial for maintaining body homeostasis. Marine collagen peptides (MCPs) and Glycosaminoglycans (GAGs) have been described as potential wound healing (WH) agents. Recently, through an ex vivo clinical approach, we have demonstrated the nutricosmetic potential of fish cartilage hydrolysate (FCH), which presents a combination of collagen peptides and GAGs. Here, we coupled a clinical approach with in vitro experiments on human dermal fibroblasts (HDFs) and applied a Data Independent Acquisition - Parallel Accumulation Serial Fragmentation (diaPASEF) proteomic analysis, to assess the potential benefit of FCH in WH and its mode of action. Our results show that human serum enriched with circulating metabolites resulting from FCH ingestion, improved wound closure in scratch assays. In support, some proteins with anti-inflammatory and immunomodulatory properties or prone to promote hydration and extracellular matrix (ECM) stability showed increased expression in HDFs, after exposure to FCH-enriched serum. These findings suggest that FCH appears as a promising nutrient for WH and skin regeneration.

A method was developed to perform shape optimization of a tidal stream turbine hydrofoil using a multi-objective genetic algorithm. A bezier curve parameterized the refrence hydrofoil profoil NACA 63815. Shape optimization of this hydrofoil maximized its lift-to-darg ratio and minimized its pressure coefficient, thereby increasing the turbines power output power and improving its cavitation characteristics. The Elitist Non-dominated Sorting Genetic Algorithm (NSGA-II) was employed to perform the shape optimization. A comparative study of two-and three-dimensional optimizations was carried out. The effect of varing the angle of attack on the quality of optimized results was also studied. predictions based on two-dimensional panel method results was also studied. Preditions based on a two-dimensional panel method and on a computational fluid dynamics code were compared to experimental measurments.

Aim: Ovarian cancer is the leading cause of gynecological cancer deaths worldwide. Treatment methods are listed as surgery, chemotherapy and radiotherapy depending on the stage of the cancer, but developing resistance to chemotherapy increases the need for alternative agents that act on the same pathways. In this study, the effects of rosmarinic acid (RA) and doxorubicin (DX) on the activation of FOXP3, an important tumor suppressor gene, in OVCAR3 cells were examined. Material Method: In the study, human ovarian adenocarcinoma cell line was used. MTT test was applied to determine the effect of rosmarinic acid and doxorubicin on the proliferation of OVCAR3 cells. Expression levels of FOXP3 for cell proliferation and Capase-3 for Apoptosis were determined by qRT-PCR and Western blot analysis. Wound healing model was applied to determine metastasis. The results were evaluated with one-way ANOVA in SPSS 20.0 program as p≤0.05. Results: It was determined that rosmarinic acid alone and in combination with doxorubicin inhibited the proliferation of OVCAR3 cells in a time- and dose-dependent manner for 24, 48 and 72 hours, and caused the cells to die by causing them to undergo apoptosis. It was observed that Caspase-3 expression increased approximately tenfold in OVCAR3 cells, while FOXP3 expression increased only in RA treatment and was downregulated in DX and RA+DX treatments. Coclusion According to the results of our study, it was observed that many steps of the signaling pathways related to proliferation, migration and apoptosis were affected by the combination of RA and DX in OVCAR3 cells. This shows that RA will gain an important place in cancer treatment with more comprehensive studies.

Many signaling pathways, molecular and cellular actors which are critical for wound healing have been implicated in cancer metastasis. These two conditions are a complex succession of cellular biological events and accurate regulation of these events is essential. Apart from inflammation, macrophages-released ROS arise as major regulators of these processes. But, whatever the pathology concerned, oxidative stress is a complicated phenomenon to control and requires a finely tuned balance over the different stages and responding cells. This review provides an overview of the pivotal role of oxidative stress in both wound healing and metastasis, encompassing the contribution of macrophages. Indeed, macrophages are major ROS producers but also appear as their targets since ROS interfere with their differentiation and function. Elucidating ROS functions in wound healing and metastatic spread may allow the development of innovative therapeutic strategies involving redox modulators.

An oceanographic cruise from southern Adriatic to the northern Ionian basins, during 2013 spring period, allowed us to describe spatial abundance and distribution of decapod crustacean larval assemblages with a multidisciplinary approach. Seventeen locations on the Apulian and Albanian shelves and offshore waters, including the Strait of Otranto, were sampled by BIONESS electronic multinet. In May 2013 a swarm of zoeae (11 Brachyura taxa, mostly at first instar, with Xantho granulicarpus at 87%) was recorded in the neuston of the Italian side. Decapod larvae were concentrated in the first 20-30 m surface layer, strongly linked to the thermocline and generally above the DCM, suggesting that they are involved in surface water circulation. The migratory behavior of decapod larvae in coastal stations is quite regular between 20 and 60 m depth and daily time independent. In offshore stations, migration is compatible with the day-night cycle, where a minimum WMD value is evident at about 20m at night. The availability of four satellite-tracked surface drifters in the same area and period of the larvae presence, represented a possibility to discuss the geographic dispersal of larvae linked to the surface circulation in successive days. Only one drifter crossed the south Adriatic passing from the Italian to the Balkan neritic area, employing about 40 days. The actual genetic homogeneity of many Brachyura coastal species populations on the opposite sides of the Adriatic Sea, suggests the existence of a genetic connection which should not rely exclusively upon larvae circulation and needs to be fueled by additional strategies of biological communication.

Evaporating liquid sessile drop deposited on horizontal surface is an important object of applications (printing technologies, electronics, sensorics, medical diagnostics, hydrophobic coatings, etc.) and theoretical investigations (microfluidics, self-assembly of nanoparticle, crystallization of the solute, etc.). The arsenal of formulas for calculating the slow evaporation of an axisymmetric drop of capillary dimensions deposited on a flat solid surface is reviewed. Such characteristics as vapor density, evaporation flux density, total evaporation rate are considered. Exact solutions obtained in the framework of the Maxwellian model, in which the evaporation process of the drop is limited by vapor diffusion from the drop surface to the surrounding air, are presented. The summary covers both well-known results obtained during the last decades and new results published by us in the last few years, but practically unknown to the wide scientific community. The newest formulas, not yet published in refereed publications, concerning exact solutions for a number of specific contact angles are also presented. In addition, new approximate solutions are presented for the first time (total evaporation rate and mass loss per unit surface area per unit time in the whole range of contact angles ), which can be used in modeling without requiring significant computational resources.

Inteins, often referred to as protein introns, are highly mobile genetic elements that invade conserved genes throughout the tree of life. Inteins have been found to invade a wide variety of key genes within actinophages. While in the process of conducting a survey of these inteins in actinophages we discovered that one protein family of methylases contained a putative intein, and two other unique insertion elements. These methylases are known to occur commonly in phages as orphan methylases (possibly as a form of resistance to restriction-modification systems). We found that the methylase family is not conserved within phage clusters and has a disparate distribution across divergent phage groups. We determined that two of the three insertion elements have a patchy distribution within the methylase protein family. We also found that the third insertion element is likely a second homing endonuclease, and that all three elements (the intein, the homing endonuclease, and what we refer to as the ShiLan domain) all have different insertion sites that are conserved in the methylase gene family. Furthermore, we find strong evidence that both the intein and ShiLan domain are partaking in long distance horizontal gene transfer events between divergent methylases in disparate phage hosts within the already dispersed methylase distribution. The reticulate evolutionary history of methylases and their insertion elements reveals high rates of gene transfer and within-gene recombination in actinophages.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

The aim of this work is to evaluate the impact of proposed modifications to conventional capturing and discharging effluents devices in Subsurface Flow Wetland (SSFW) systems. Main modifications proposed consist on extending the influence of the capture and discharge device in such a way that the SSFW width and height are fully covered. Additionally an SSFW prototype was built as pilot including the proposed modifications and the impact of the innovative device is measured based on the efficiency of the Chemical Oxygen Demand (COD) removal as compared to a traditionally built SSFW. The results show that for the innovative device, the COD removal was 10% higher than for the conventional device.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

Background: The aim of this study was to investigate a series of complete blood cell count – based biomarkers of systemic inflammation as predictors of clinical outcomes in patients who underwent first-line chemoimmunotherapy for advanced NSCLC. Methods: Consecutive patients with pathologically diagnosed stage III/IV NSCLC who underwent first-line chemoimmunotherapy were retrospectively enrolled. The clinical outcomes used for biomarker evaluation were Objective Response Rate (ORR) and Overall Survival (OS). Results: Non-responders had significantly higher values of neutrophil to lymphocyte ratio (NLR, median: 5.36; IQR: 2.78–10.82 vs. 3.31; IQR: 2.15–4.12, p = 0.019), neutrophil to monocyte ratio (NMR, median: 14.00; IQR: 8.82–21.20 vs. 9.20; IQR: 7.45–11.20, p = 0.013), and systemic inflammation index (SII, median: 1,395; IQR: 929–3,334 vs. 945; IQR: 552–1,373, p = 0.025), but only NLR and NMR remained independently related with clinical response in multivariate logistic regression. In univariate analysis white blood cells (OR:1.2202; 95% CI: 1.0339 - 1.4400, p=0.019), neutrophils (OR:1.2916; 95% CI: 1.0692 - 1.5604, p=0.008), NLR (OR:1.3601: 95% CI: 1.0949 - 1.6896, p=0.005) and NMR (OR:1.2159; 95% CI: 1.00396 - 1.4221, p=0.015) were significantly associated with survival; Cox regression models confirmed that neutrophils, NLR and MLR were independently associated with survival; NLR at a cut-off value of 4.0 showed the better AUC (0.749) in predicting survival. Conclusions: Baseline complete blood cell count biomarkers, especially the NLR, can predict clinical outcomes in patients with advanced NSCLC treated with first-line chemoimmunotherapy.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

The discovery by the Large Area Telescope on board Fermi of variable gamma-ray emission from radio-loud narrow-line Seyfert 1 (NLSy1) galaxies revealed the presence of a possible third class of AGN with relativistic jets in addition to blazars and radio galaxies. Considering that NLSy1 are usually hosted in spiral galaxies, this finding poses intriguing questions about the nature of these objects and the formation of relativistic jets. We report on a systematic investigation of the gamma-ray properties of a sample of radio-loud NLSy1, including the detection of new objects, using 7 years of Fermi-LAT data with the new Pass 8 event-level analysis. In addition we discuss the radio-to-very-high-energy properties of the gamma-ray emitting NLSy1, their host galaxy, and black hole mass in the context of the blazar scenario and the unification of relativistic jets at different scales.

The Italian herbal products market is the most prosperous in Europe. The proof is represented by the use of these products in several marketing categories, ranging from medicine to nutrition and cosmetics. Market and legislation in Italy are at the same time cause and consequence of this peculiar situation. In fact, the legislation on botanical food supplements in Italy is very permissive and at the same time the market shows an overall satisfaction of users and strong feedback in terms of consumption, which brings a widening use of medicinal plants, formerly the prerogative of pharmaceuticals, to other fields such as nutrition. This review summarizes the market and normative panorama of herbal products in Italy, highlighting the blurred boundaries of health indications, marketing authorizations and quality controls between herbal medicines and non pharmaceutical products, such as food supplements, cosmetics and other herbal-based “parapharmaceuticals”.

The straight leg raise test (SLR) has been proposed to detect increased nerve mechanosensitivity of the lower limbs in individuals with low back pain or leg-related low back pain. However, its validity in the diagnosis of lumbosacral radiculopathy show very variable results. The aim of this study was to analyse the diagnostic validity of the SLR including well defined diagnostic criteria in a sample of participants in phase III with suspicion of lumbar radiculopathy using the nerve conduction studies (NDS) as the reference standard. A phase III diagnostic accuracy study was designed. 142 individuals with suspected lumbosacral radiculopathy referred for NCS participated in the study. Each participant was tested with NCS and SLR. SLR was considered positive using three diagnostic criteria. The sensitivity of the SLR for the criterion 3 was 89.02% (CI 81.65-96.40), the specificity was 25.00% (CI 13.21-36.79), and the +LR and -LR were 1.19 (CI 1.01-1.40) and 0.44 (0.21-0.94), respectively. SLR showed limited validity in the diagnosis of lumbosacral radiculopathy. The incorporation of more objective diagnostic criteria (asymmetry in range of motion or localization of symptoms) improved diagnostic validity but the imprecision of the confidence intervals limited the interpretation of the results.

Aim: Ovarian cancer is one of the most frequently diagnosed cancers in women in the world. Recognition of the differences between tumors in cancers and resistance to treatment in patients have made the treatment potential of chemotherapy, radiotherapy and immunotherapy controversial. Especially against drug resistance, laboratories have implemented the drug diversion system by putting old drugs into new forms. In this study, the cytotoxic and apoptotic effects of the combination of doxorubicin (DX) and thymoquinone (TQ) on ovarian adenocarcinoma cells (OVCAR3) were investigated. Material Method: OVCAR3 cell line was cultured in RPMI medium containing 10% FBS, 1% penicillin/streptomycin. Cell viability and cell growth rate were determined by MTT viability test by combining doxorubicin and thymoquinone. Nucblue immunofluorescent staining was used to determine the mechanism of cell death at different doses of doxorubicin and thymoquinone compounds, qRT-PCR to determine the pathways underlying the apoptotic mechanism, and western blot methods to show protein levels. Result: We found that the combination of DX and TQ reduced the viability of OVCAR3 cells (MTT assay), induced apoptosis (RAF, RAS, Bcl2, Bax by qRT-PCR) and increased RAF, RAS protein levels in TQ and DX-treated cells by western blot analysis. Conclusion: The results obtained revealed for the first time that combining DX and TQ also had cytotoxic/apoptotic and anti-proliferative effects against ovarian adenocarcinoma cells.

Efficient quality evaluation provides support for the timely and good maintenance of the lane line marking. This paper searches and optimizes the back propagation(BP) network model which referred to the analytic hierarchy process(AHP) model structure, as well as the number of nodes in the middle layer network. Based on this, a comprehensive evaluation method of multi-dimensional lane line quality such as shape, color and contrast is established. The experimental results show that the parameters of the model are more simplified, and the scoring and classification results of lane lines are more accurate.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

(1) Background: This manuscript introduces the "Lines and Dots" (LAD) technique, a novel method for administering Botulinum Toxin Type A (BoNT-A) in treating horizontal forehead lines. This technique emphasizes precision in targeting nerve endplates, considering individual anatomical variations, and optimizing treatment efficacy. (2) Methods: The LAD technique focus on using the frontalis muscle contraction dynamics to identify the specific distribution of the supraorbital and supratrochlear nerves It involves creating a grid of predetermined lines and points on the forehead that align with nerve paths and motor endplate zones. (3) Results: By targeting injections along these precise lines and points, the LAD technique ensures more effective utilization of BoNT-A. This approach not only enhances the toxin's effect but also allows for a reduction in the overall dosage. The strategic placement of injections results in a more natural, symmetrical, and sustained therapeutic effect, ensuring an improved aesthetic outcome. (4) Conclusions: The LAD technique represents a significant advancement in the realm of cosmetic injectables. It offers a tailored, patient-specific approach, maximizing the effectiveness of BoNT-A injections for treating forehead lines while minimizing risks and enhancing patient satisfaction. This method underscores the importance of a deep anatomical understanding and precision in cosmetic procedures.

Horizontal transfer of transposons (HTT) is an important source of genomic evolution in eukaryotes. The HTT dynamics is well characterized in eukaryotes including insects however, but there is a huge gap of knowledge about HTT regarding many eukaryotes’ species. In this study we analyzed the events of the HTT between Rhus gall aphids (Hemiptera) and other insects. We analyzed the Mariner-like transposable elements (MLEs) belongs to Rhus gall aphids for the possible HT events. The MLEs have patchy distribution and have high similarity over the entire length of element with insects MLEs from different orders. We selected representative sequences from the Rhus gall MLEs and identified five events of HT between MLEs of Rhus gall aphids and other insects from five different orders. We also found multiple HTT events among the MLEs of insects from the five orders which demonstrate that these Mariner elements have been involved in recurrent HT between these six order of insects. Our current study closed the knowledge gap of HTT and reported the events between Rhus gall aphids and other insects for the first time. We believe that this study about HTT events will help to understand the evolution and spread of transposable elements in the genomes of Rhus gall aphids.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Steel fibres provides ductility to concrete structures. This in turn gives possibility to replace or reduce conventional reinforcement in structural elements. In this study the focus is on structural walls and the fibres as potential replacement for horizontal reinforcement in areas where vertical re-bars are needed. An experimental study was conducted, in which prismatic specimens with longitudinal re-bars were subjected to centric loading. Ten samples with 12 specimens in each were tested. The parameters considered were: fibre content, concrete cover for the longitudinal bars, and presence of stirrups. Self-compacting concrete with 30 and 60 kg/m3 steel fibres was used. The influence of fibres on maximum load, stiffness, and ductility of the specimens is evaluated. The results show that fibres eliminated brittle collapse and spalling of concrete at failure. Samples with fibres tend to have reduced maximum force and stiffness but increased ductility. The specimens with fibre content of 60 kg/m3 showed more ductile behaviour than the ones with minimum amount of conventional stirrups. The study suggests that combination of steel fibres and conventional re-bars can lead to less qualitative compactness of the self-compacting concrete, which in turn may reduce load bearing capacity and stiffness of the structure.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

Genes coding for enzymes of the denitrification pathway appear randomly distributed among isolates of the ancestral genus Thermus, but only in few strains of the species T. thermophilus the pathway has been studied to a certain detail. Here, we review the enzymes involved in this pathway present in T. thermophilus NAR1, a strain extensively employed as a model for nitrate respiration, on the light of its full sequence recently assembled through a combination of PacBio and Illumina technologies in order to counteract the systematic errors introduced by the former technique. The genome of this strain is divided in four replicons, a chromosome of 2,021,843 pb, two megaplasmids of 370,865 and 77,135 bp and a small plasmid of 9,799 pb. Nitrate respiration is encoded in the largest megaplasmid, pTTHNP4, within a region that includes operons for O2 and nitrate sensory systems, a nitrate reductase, nitrate and nitrite transporters and a nitrate specific NADH dehydrogenase, in addition to multiple insertion sequences (IS), suggesting its mobility-prone nature. Despite nitrite is the final product of nitrate respiration in this strain, the megaplasmid encodes two putative nitrite reductases of the cd1 and Cu-containing types, apparently inactivated by IS. No nitric oxide reductase genes have been found within this region, although the NorR sensory gene, needed for its expression, is found near the inactive nitrite respiration system. These data clearly support that partial denitrification in this strain is the consequence of recent deletions and IS insertions in genes involved in nitrite respiration. Based on these data, the capability of this strain to transfer or acquire denitrification clusters by horizontal gene transfer is discussed.

Horizontal gene transfer (HGT) is the transmission of genes between organisms by other means than parental to offspring inheritance. While it is prevalent in prokaryotes, HGT is less frequent in eukaryotes and particularly in metazoan. Here, we propose Alienness, a taxonomy-aware web application that parses BLAST results against public libraries to rapidly identify candidate HGT in any genome of interest. Alienness takes as input the result of a BLAST of a whole proteome of interest against any NCBI protein library. The user defines recipient (e.g. metazoan) and donor (e.g. bacteria, fungi) branches of interest in the NCBI taxonomy. Based on the best BLAST E-values of candidate donor and recipient taxa, Alienness calculates an Alien Index (AI) for each query protein. An AI >0 indicates a better hit to candidate donor than recipient taxa and a possible HGT. Higher AI represent higher gap of E-values between candidate donor and recipient and a more likely HGT. We confirmed the accuracy of Alienness on phylogenetically confirmed HGT of non-metazoan origin in plant-parasitic nematodes. Alienness scans whole proteomes to rapidly identify possible HGT in any species of interest and thus fosters exploration of HGT more easily and largely across the tree of life.

This study assesses the impact of nurse-originated changes in central venous catheter (CVC) management on the incidence of central line-associated bloodstream infections (CLABSI) and catheter-related bloodstream infections (CRBSI). It is a single-center retrospective cohort study conducted at an urban, tertiary referral, and academic center serving pediatric patients. The study cohort comprised 236 patients and 323 CVCs seen between 2012 and 2022. CLABSI and CRBSI were defined according to the Centers for Disease Control and Prevention definitions. Oncology nurse leaders developed CVC-specific educational modules for CLABSI prevention. All relevant information during the CVC maintenance period was noted in the patient's CVC logbook. 24 (7%) cases of confirmed CLABSI were identified. The incidence of CVC-related infections was 0.32 cases per 1000 catheter days. The incidence decreased by 40% between the first and second three-year study period. Documented exit-site infection was reported in 32 (10%) cases. The correlation between exit-site infection and CLABSI was found in 9 (28%) cases. Our CVC-related infection rates are significantly lower than the incidence reported by the Italian Association of Pediatric Hematology and Oncology, which settles at 3-5 cases per 1000 catheter days. Our data confirm the effectiveness of local CVC management guidelines in preventing CVC-related infectious complications.

A recent study by the Wall Street Journal reveals that the hydrofractured horizontal wells in shales have been producing less than forecasted by the industry with the empirical hyperbolic decline curve analysis (DCA). As an alternative to DCA, we introduce a simple, fast and accurate method of estimating ultimate recovery (EUR) in oil shales. We adopt a physics-based scaling approach to analyze oil rates and ultimate recovery from 14,888 active horizontal oil wells in the Bakken shale. To predict EUR, we collapse production records from individual horizontal shale oil wells onto two segments of a master curve: (1) We find that cumulative oil production from 4,845 wells is still growing linearly with the square root of time; and (2) 6,401 wells are already in exponential decline after approximately seven years on production. In addition, 2,363 wells have discontinuous production records, because of refracturing or changes in downhole flowing pressure, and are matched with a linear combination of scaling curves superposed in time. The remaining 1,279 new wells with less than 12 months on production have too few production records to allow for robust matches. These wells are scaled with the slopes of other comparable wells in the square-root-of-time flow regime. In the end, we predict that total ultimate recovery from all existing horizontal wells in Bakken will be some 4.5 billion barrels of oil. We also find that wells completed in the Middle Bakken formation, in general, produce more oil than those completed in the Upper Three Forks formation. The newly completed longer wells with larger hydrofractures have higher initial production rates, but they decline faster and have EURs similar to the cheaper old wells. There is little correlation among EUR, lateral length, and the number and size of hydrofractures. Therefore, technology may not help much in boosting production of new wells completed in the poor immature areas along the edges of the Williston Basin. Operators and policy-makers may use our findings to optimize the possible futures of the Bakken shale and other plays. More importantly, petroleum industry may adopt our physics-based method as an alternative to the overly-optimistic hyperbolic DCA that yields an "illusory picture" of shale oil resources.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

We address the unsolved question of how best to estimate the collision entropy, also called quadratic or second order Rényi entropy. Integer-order Rényi entropies are synthetic indices useful for the characterization of probability distributions. In recent decades, numerous studies have been conducted to arrive at their valid estimates starting from experimental data, so to derive suitable classification methods for the underlying processes, but optimal solutions have not been reached yet. Limited to the estimation of collision entropy, a one-line formula is presented here. The results of some specific Monte Carlo experiments give evidence of the validity of this estimator even for the very low densities of the data spread in high-dimensional sample spaces. The method strengths are unbiased consistency, generality and minimum computational cost.

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

Local binary pattern is one of the visual descriptors and can be used as a powerful feature extractor for texture classification. In this paper, a novel representation for face recognition is proposed, called it Bilateral Line Local Binary Patterns (BL-LBP). This scheme is an extension of Line Local Binary Patterns descriptors in the statistical learning subspace. The present bilateral descriptors are fused with an ensemble learning of calibrated SVM models. The performance of this scheme is evaluated using 5 standard face databases. It is found that it is robust against illumination variation, diverse facial expressions and head pose variations and its recognition accuracy reaches 98 percent, running on a mobile device with a processing speed of 63 ms per face. Results suggest that our proposed method can be very useful for the vision systems that have limited resources where the computational cost is critical.

Currently, narrowband Power line communication (PLC) is considered as an attractive communication system in smart grid environments for applications such as advanced metering infrastructure (AMI). In this paper, we will present a comprehensive comparison and analysis in time and frequency domain of noise measured in China and Italy. In addition, impulsive noise in these two countries are mainly analyzed and modeled using two probability based models, Middleton Class A (MCA) model and \(\alpha\) stable distribution model. The results prove that noise measured in China is rich in impulsive noise, and can be modeled well by \(\alpha\) stable distribution model, while noise measured in Italy has less impulsive noise, and can be better modeled by MCA model.

The asymmetric bimodal exponential power (ABEP) distribution is an extension of the generalized gamma distribution to the real line via adding two parameters which fit the shape of peakedness in bimodality on real line. The special values of peakedness parameters of the distribution are combination of half Laplace and half normal distributions on real line. The distribution has two parameters fitting the height of bimodality, so capacity of bimodality is enhanced by using these parameters. Adding a skewness parameter is considered to model asymmetry in data. The location-scale form of this distribution is proposed. The Fisher information matrix of these parameters in ABEP is obtained explicitly. Properties of ABEP are examined. Real data examples are given to illustrate the modelling capacity of ABEP. The replicated artificial data from maximum likelihood estimates of parameters of ABEP and distributions having an algorithm for artificial data generation procedure are provided to test the similarity with real data.

When the distance between an obstacle and a power line is less than the discharge distance, a discharge arc can be generated, resulting in interruption of power supplies. Therefore, regular safety inspections are necessary to ensure safe operations of power grids. Tall vegetation and buildings are the key factors threatening the safe operation of extra high voltage transmission lines within a power line corridor. Manual or LiDAR based-inspections are time consuming and expensive. To make safety inspections more efficient and flexible, a low-altitude unmanned aerial vehicle remote-sensing platform equipped with optical digital camera was used to inspect power line corridors. We propose a semi-patch matching algorithm based on epipolar constraints using both correlation coefficient and the shape of its curve to extract three dimensional (3D) point clouds for a power line corridor. Virtual photography was used to transform the power line direction from approximately parallel to the epipolar line to approximately perpendicular to epipolar line to improve power line measurement accuracy. The distance between the power lines and the 3D point cloud is taken as a criterion for locating obstacles within the power line corridor automatically. Experimental results show that our proposed method is a reliable, cost effective and applicable way for practical power line inspection, and can locate obstacles within the power line corridor with measurement accuracies better than ±0.5 m.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

Comprehending the replication kinetics of SARS-CoV-2 variants helps explain why certain var-iants spread more easily and are more contagious, and pose significant health menaces to the global populations. The replication kinetics of Malaysian isolates of the Alpha, Beta, Delta, and Omicron variants were studied in the Vero E6 cell line. Their replication kinetics were deter-mined using the plaque assay, quantitative real-time PCR (qRT-PCR), and viral growth curve. The Beta variant exhibited the highest replication rate at 24 hours post-infection (h.p.i), as evi-denced by the highest viral titers and lowest viral RNA multiplication threshold. The plaque phenotypes also varied among the variants, in which the Beta and Omicron variants formed the largest and smallest plaques, respectively. All studied variants showed strong cytopathic effects after 48 h.p.i. The whole-genome sequencing highlighted cell-culture adaptation, where the Beta, Delta and Omicron variants acquired mutations at the multibasic cleavage site after three cycles of passaging. The findings suggest a strong link between the replication rates and their respec-tive transmissibility and pathogenicity. This is essential in predicting the impacts of the upcom-ing variants on the local and global populations and is useful in designing preventive measures to curb the virus outbreaks.

The extraction of cell cultures from fresh tissue is a process that requires significant computa-tional resources and is associated with substantial overheads. The objective of our research is to de-vise a rapid, straightforward, and efficient technique for the cultivation of neuronal cells derived from frozen biological material. We utilized freshly isolated hippocampus and cerebral cortex tissue from rats, in addition to whole brain tissue. This tissue underwent digestion and processing to yield a cellular suspension. This suspension was subsequently cryopreserved using a variety of cryopro-tectants: CTS™ Synth-a-Freeze™, SpermFreeze®, and a medium supplemented with 10% DMSO. CTS™ Synth-a-Freeze™ is a commercially available cryoprotectant typically employed in the preservation of cellular cultures, while the addition of 10% DMSO to the medium is a conventional technique for the cryopreservation of cells to mitigate damage. The innovative aspect of our meth-odology is the application of SpermFreeze®, a product used for the cryopreservation of sperm in in vitro clinics. We postulated that SpermFreeze® might enhance the viability and quality of the cryo-preserved neuronal cells, given the delicate and energetically demanding nature of both sperm and neuronal cells. The ultimate objective was to ascertain whether a cryoprotectant formulated for sperm could augment the post-thawing efficacy of our nervous system cells. This investigation intro-duces an innovative methodology for the optimization of neuronal cell isolation and cryopreserva-tion from animal-derived tissues.