A method was developed to perform shape optimization of a tidal stream turbine hydrofoil using a multi-objective genetic algorithm. A bezier curve parameterized the refrence hydrofoil profoil NACA 63815. Shape optimization of this hydrofoil maximized its lift-to-darg ratio and minimized its pressure coefficient, thereby increasing the turbines power output power and improving its cavitation characteristics. The Elitist Non-dominated Sorting Genetic Algorithm (NSGA-II) was employed to perform the shape optimization. A comparative study of two-and three-dimensional optimizations was carried out. The effect of varing the angle of attack on the quality of optimized results was also studied. predictions based on two-dimensional panel method results was also studied. Preditions based on a two-dimensional panel method and on a computational fluid dynamics code were compared to experimental measurments.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

The development and application of marine current energy are attracting more and more attention around the world. Due to the hardness of its working environment, it is important and difficult to study the fault diagnosis of a marine current generation system. In this paper, an underwater image is chosen as the fault-diagnosing signal, after different sensors are compared. This paper proposes a diagnosis method based on the sparse autoencoder (SA) and softmax regression (SR). The SA is used to extract the features and SR is used to classify them. Images are used to monitor whether the blade is attached by benthos and to determine its corresponding degree of attachment. Compared with other methods, the experiment results show that the proposed method can diagnose the blade attachment with higher accuracy.

There is no doubt that seagrass beds constitute one of the most productive ecosystems in shallow coastal waters. Despite this, picoplankton in seagrass ecosystems has received relatively little attention. The purpose of this study was to compare picoplankton growth and mortality rates between seagrass and unvegetated habitats using chamber incubations. We tested two main hypotheses: (i) incubation with seagrass would result in higher bacterial growth rates due to increased DOM release from seagrass photosynthesis, and (ii) Synechococcus spp. would be lower in the presence of seagrass due to competition for inorganic nutrients. Our results showed bacterial growth rates of 2.31 and 2.44 d–1 without and with seagrass, respectively. In seagrass chambers, bacterial growth was higher than that in non-seagrass chambers, suggesting that organic carbon coming from the seagrass community may support bacterial production. Furthermore, we observed a negative Synechococcus spp. growth rate (-0.9 d–1) in the seagrass treatment, likely reflecting nutrient competition with the seagrass. Small-scale chambers proved to be a useful tool for studying the factors controlling spatial and temporal patterns of picoplankton across different habitats. Furthermore, future studies should examine picoplankton growth over a wider range of spatial scales in seagrass beds and adjacent unvegetated sediment.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

Indole is a versatile pharmacophore widely distributed in bioactive natural products. This privileged scaffold has been found in a variety of molecules isolated from marine organisms such as algae and sponges. Among these, indole alkaloids represent one of the biggest, most promising family of compounds, having shown a wide range of pharmacological properties, including anti-inflammatory, antiviral and anticancer activities. The aim of this review is to show the current scenario of marine indole alkaloid derivatives, covering not only the most common chemical structures, but also new synthetic routes developed during the last years as well as promising therapeutic applications.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Tidal stream energy, due to its high level of consistency and predictability, is one of the feasible and promising type of renewable energy for future development and investment. Applicability of Blade Element Momentum (BEM) method for modeling the interaction of turbines in tidal arrays has been proven in many studies. Apart from its well-known capabilities, yet there is scarcity of research using BEM for the modeling of tidal stream energy farms considering full scale rotors. In this paper, a real geographical site for developing a tidal farm in the southern coasts of Iran is selected. Then, a numerical methodology is validated and calibrated for the selected farm by analyzing array of turbines. A linear equation is proposed to calculate tidal power of marine hydrokinetic turbines. This methodology narrows down the wide range of turbine array configurations, reduces the cost of optimization and focuses on estimating best turbine arrangements in a limited number of positions.

In mesoscale eddies, chemical properties and biological composition are different from those in surrounding water, due to their unique physical processes. It is unclear how physical-biological coupling occurs in warm-core eddies, particularly since no study has examined the relationship between bacteria and viruses. The purpose of the present study was to examine the influence of anticyclonic warm eddy on the relationship between bacterial and viral abundances as well as viral activity (viral production) in different depths. In the core of warm eddy, bacterial abundance (0.48 to 2.82 ×105 cells mL−1) fluctuated less than that of the outside eddy (1.12 to 7.03×105 cells mL−1). In particular, there was four-folds higher of viral-bacterial abundance ratio (VBR) estimated within the eddy below DCM than the outside eddy. We suggest that prevailing physical forces with downwelling at the center of the anticyclonic warm eddy, viruses can also be transmitted into the deep ocean directly through adsorption on particulate organic matter during sinking. Overall, our findings provide valuable insights into the interaction between bacterial and viral communities and their ecological mechanism within the warm eddy.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

The cost effective design of tidal turbines requires a good estimation of the loading cycles and their extrema that are related to the unsteady fluctuations of the current velocity. Apart from the ambient turbulence, the main source of velocity fluctuations is the presence of surface waves. In the present study, we analyse the effect of waves propagating against the current on the performance and the loads of a twin vertical axis tidal turbine by an experimental approach at a 1/20 scale. Overall, the results show little or no effect of the waves on the average power and loads compared to the condition with current only, but a significant impact on their standard deviation that rises linearly with the waves amplitude. The drag, lift and pitching moment show extended ranges up to 7.5 times higher and extreme values exceedance by 60 to 100 % with irregular waves compared to the condition without waves. Those load and power fluctuation increase are fully due to the presence of waves as the coherence function between the rotor torque or the loads and the velocity spectra exceed 0.5 on the whole wave frequency bandwidth. The results also reveal a rotational sampling of the waves by the rotors that had also been observed on horizontal axis turbines. From a structural design point of view, the authors recommand to conduct tests in irregular wave conditions as the loads range and extreme values are 1.5 to 2 times higher than those encountered with regular waves of the same significant height and period.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

The mechanism of sex determination and differentiation in animals remains a central focus of reproductive and developmental biology research, and the regulation of sex differentiation in amphioxus remains poorly understood. Cytochrome P450 Family 19 Subfamily A member 1 (CYP19A1) is a crucial sex differentiation gene that catalyzes the conversion of androgens into estrogens. In this study, we identified two aromatase-like genes in amphioxus: cyp19-like1 and cyp19-like2. Cyp19-like1 is more primitive and may represent the ancestral form of cyp19 in zebrafish and other vertebrates. Cyp19-like2, on the other hand, is likely the result of gene duplication within am-phioxus suggesting its potential role as a key gene in sex differentiation. To gain further insights into the expression patterns of these two aromatase-like, we examined their expression in different gonad tissues and during different stages of gonad development. While the expression patterns of the two genes differ in gonad tissues, both are highly expressed in the gonad primordium and are primarily localized to microsomal membrane systems. However, as development proceeds, their expression levels decrease significantly. This study enhances our understanding of sex dif-ferentiation mechanisms in amphioxus and provides valuable insights into the formation and evolution of sex determination mechanisms in vertebrates.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

The microbial colonisers of plastics – the ‘plastisphere’ – can affect all interactions that plastics have with their surrounding environments. While only specifically characterised within the last 10 years, at the beginning of 2021 there were 140 primary research and 65 review articles that investigate at least one aspect of the plastisphere. We gathered information on the locations and methodologies used by each of the primary research articles, highlighting several aspects of plastisphere research that remain understudied: (i) the non-bacterial plastisphere constituents; (ii) the mechanisms used to degrade plastics by marine isolates or communities; (iii) the capacity for plastisphere members to be pathogenic or carry antimicrobial resistance genes; and (iv) meta-OMIC characterisations of the plastisphere. We have also summarised the topics covered by the existing plastisphere review articles, identifying areas that have received less attention to date – most of which are in line with the areas that have fewer primary research articles. Therefore, in addition to providing an overview of some fundamental topics such as biodegradation and community assembly, we discuss the importance of eukaryotes in shaping the plastisphere, potential pathogens carried by plastics and the impact of the plastisphere on plastic transport and biogeochemical cycling. Finally, we summarise the future directions suggested by the reviews that we have evaluated and suggest other key research questions.

Chitin/chitosan and collagen are two of the most important bioactive compounds with applications in the pharmaceutical, veterinary, nutraceutical, cosmetic, biomaterials, and other industries. When extracted from fish and shellfish non-edible parts, by-catches, and invasive species, their use contributes to a more sustainable and circular economy. The present article reviews the scientific knowledge and publication trends along the marine chitin/chitosan and collagen value-chains and assesses how researchers, industry players, and end-users can bridge the gap between scientific understanding and industrial applications. Overall, research on chitin/chitosan remains focused on the compound itself rather than its market applications. Still, chitin/chitosan use is expected to increase in food and biomedical applications, while that of collagen is expected to increase in biomedical, cosmetic, pharmaceutical, and nutritional applications. Sustainable practices, such as the reuse of waste materials, contribute to strengthen both value-chains; the identified weaknesses include the lack of studies considering market trends, social sustainability, and profitability, as well as insufficient examination of intellectual property rights. Government regulations, market demand, consumer preferences, technological advancements, environmental challenges, and legal frameworks play significant roles in shaping both value-chains. Addressing these factors is crucial for seizing opportunities, fostering sustainability, complying with regulations, and maintaining competitiveness in these constantly evolving value-chains.

Text mining is a technological trend often highlighted in the continuous exchange of information through interconnected media. Its applicability goes beyond private organizations, as the public sector also requires it to treat textual information regarding services offered. Within this scenario, public security emerges as a prominent user of text mining that seeks to ensure the construction of data and knowledgebases to support decision-making about law enforcement actions to ensure citizen welfare. The primary objectives of this article are: (i) to develop a survey to identify text mining applications, techniques, opportunities, and challenges in public security, and (ii) to outline research directions concerning these topics and provide insights so that interested researchers can develop new studies. The literature was searched within four databases: Scopus, IEEE Xplore, ACM Digital Library, and Web of Science. A filtering process was applied to extract the works most aligned with the target theme, resulting in the selection of 194 of the most relevant works for a literature review. There were identified nineteen key applications of text mining related to public security and the most recurrent techniques and technologies reported between 2014 to 2021, supporting outlining three axes for future directions: one with possible expansion of objectives for new research; another on changes and adaptations in scopes for the methodological context; and the last one on expansions and changes in application scenarios based on the literature.

The epithelial cell tight junction structure is the site of the transepithelial movement of solutes and water between epithelial cells (paracellular permeability). Paracellular permeability can be divided into two distinct pathways, the Pore Pathway mediating the movement of small ions and solutes and the Leak Pathway mediating the movement of large solutes. Claudin proteins form the basic paracellular permeability barrier and mediate the movement of small ions and solutes via the Pore Pathway. The Leak Pathway remains less understood. Several proteins have been implicated in mediating the Leak Pathway, including occludin, ZO proteins, tricellulin, and actin filaments, but the proteins comprising the Leak Pathway remain unresolved. The properties of the Leak Pathway, such as its molecular mechanism, its regulation, and whether or not it has a size limit, remain controversial. This review will trace the evolution of the Leak Pathway concept from its origins, will discuss the current information about the properties of the Leak Pathway, and will discuss recent research suggesting a possible molecular basis for the Leak Pathway. Based on these findings, we propose a model for the molecular mechanism underlying the Leak Pathway and its regulation.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

Abstract: The venom-containing barb attached to their ‘whip-like’ tail provides stingrays a defensive mechanism for evading predators such as sharks. From human encounters, dermal stingray envenomation is characterized by intense pain often followed by tissue necrosis occurring over several days to several weeks. The bioactive components in stingray venoms (SRV’s) and their molecular targets and mechanisms that mediate these complex responses are not well understood. Given the utility of venom-derived proteins from other venomous species for biomedical and pharmaceutical applications, we set out to characterize the bioactivity of SRV from three local species that belong to the Dasyatoidea ‘whiptail’ superfamily. Multiple cell-based assays were used to quantify and compare the in vitro effects of these SRV’s on different cell lines. All three SRV’s demonstrated concentration-dependent growth inhibitory effects on three different human cell lines tested. In contrast, a mouse fibrosarcoma cell line was markedly resistant to all three SRV’s, indicating the molecular target(s) for mediating the SRV effects are not expressed on these cells. The multifunctional SRV responses were characterized by an acute disruption of cell adhesion leading to apoptosis. These findings aim to guide future investigations of identified SRV proteins and their molecular targets for potential use in biomedical applications.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Multivariate statistical approaches (MSA), such as principal components analysis and multidimensional scaling, seek to uncover meaningful patterns within datasets by considering multiple response variables in a concerted fashion. Although these techniques are readily used by ecologists to visualize and explain differences between study sites, they could theoretically be employed to differentiate organisms within an experimental framework while simultaneously identifying response variables that drive documented experimental differences. Therefore, MSA were used herein to attempt to understand the response of the common, Indo-Pacific reef coral Seriatopora hystrix to temperature changes using data from laboratory-based temperature challenge studies performed in Southern Taiwan. Gene expression and physiological data partitioned experimental specimens by time of sampling, treatment temperature, and site of origin upon employing MSA, signifying that S. hystrix and its dinoflagellate endosymbionts display physiological and molecular signatures that are characteristic of sampling time, site of colony origin, and/or temperature regime. These findings promote the utility of MSA for documenting biologically meaningful shifts in the physiological and/or sub-cellular response of marine invertebrates exposed to environmental change.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Maternal type 2 diabetes mellitus (T2DM) has been shown to result in fetal programming of the hypothalamus-pituitary-adrenal (HPA) axis, leading to adverse fetal outcomes. T2DM is preceded by prediabetes and shares similar pathophysiological complications. However, no studies have investigated the effects of maternal prediabetes on fetal HPA axis function and postnatal offspring development, hence this study. Pre-diabetic (PD) and non-pre-diabetic (NPD) female Sprague Dawley rats were mated with non-prediabetic males. After gestation, male pups born from the PD and NPD groups were collected. Markers of HPA axis function, adrenocorticotropin hormone (ACTH) and corticosterone were measured in all dams and pups. Glucose tolerance and expression of mineralocorticoid (MR) and glucocorticoid (GR) receptors were further measured in all pups at birth and their developmental milestones. The results demonstrated increased basal concentrations of ACTH and corticosterone in the dams from the PD group by comparison to NPD. Furthermore, the results show an increase in pups ACTH and corticosterone concentrations, impaired glucose tolerance and dysregulated MR and GR expression in the PD group at all developmental milestones. These observations reveal that pregestational prediabetes is associated with maternal dysregulation of the HPA axis, impacting offspring HPA axis development along with impaired glucose handling.

The bioactive marine sulfated polysaccharides ulvan and carrageenan, formulated in gels at 1.5, 5.0 and 10% w/w concentrations, were evaluated for their wound healing potential on second-degree burn wounds. The polysaccharide-based gels were administered on the burn-inflamed skin of hairless female SKH-hr2 mice, and the therapeutic effect of the various treatments was assessed based on histopathological analysis, the clinical condition of mice, photo-documentation, evaluation of biophysical skin parameters, and FT-IR spectroscopy.Clinical and histopathological assessment, as well as the reduction rate of the burn wound area, indicated that the 10% w/w carrageenan gel significantly enhanced wound healing, especially at the early stages of the healing process, recovering both the α-helix of collagen and the glycosaminoglycans configuration as evidenced by the FT-IR absorption bandsof skin in vivo and ex vivo. At later stages, the healing effect of the 5% w/w ulvan gel was also notably significant, indicating that carrageenan and ulvan wound dressing gels could potentially contribute to the efficient wound healing of burn wounds.

Food and Agricultural Organisation estimates from 2014 suggest 64% of the high seas migratory stocks are either overfished or undergoing overfishing. Illegal fishing exacerbates the damage to marine ecosystems, human rights, and food security, and is yet to be included in the recent United Nations (UN) draft agreement to protect high seas biodiversity. We used catch data from the Sea Around Us Project to determine trends in fishing gear use and the catches of countries fishing in the high seas. Using Two-way ANOVA, Principal Coordinates Analysis, and SIMPER Test, we found that Spain, Taiwan, Japan, Indonesia, and Ecuador had the highest catches in 2004-2014. Each decade, only 1 in 10 countries (10.8%) caught over 500,000 tonnes, leaving the remaining 90% of countries catching less than 500,000 tonnes. Further analysis showed the mean high seas catch per fishery decreased 55% between the 2000s and the 2010s. Purse seine and longline were increasingly used towards the 2010s. Catch from purse seine and longline accounted for 70.5% and 78.4% of total high seas catch in 1950-2014 and 2004-2014, respectively. Discards were unreported throughout 1950-2014, and the reporting levels of landings varied greatly between countries and gears. We call for immediate action and recommend (1) including international, overarching high seas governance to end illegal and unsustainable fishing in the high seas in the UN draft agreement, and (2) using large mobile marine protected areas in high seas fisheries management through the UN draft agreement.

Antimicrobial resistance (AMR) is one of the greatest public health challenges we are currently facing. To develop effective interventions against this, it is essential to understand the processes behind the spread of AMR. These are partly dependent on the dynamics of horizontal transfer of resistance genes between bacteria, which can occur by conjugation (direct contact), transformation (uptake from the environment) or transduction (mediated by bacteriophages). Mathematical modelling is a powerful tool to investigate the dynamics of AMR, however its application to study the horizontal transfer of AMR genes is currently unclear. In this systematic review, we searched for mathematical modelling studies which focused on horizontal transfer of AMR genes. We compared their aims and methods using a list of predetermined criteria, and utilized our results to assess the current state of this research field. Of the 43 studies we identified, most focused on the transfer of single genes by conjugation in Escherichia coli in culture, and its impact on the bacterial evolutionary dynamics. Our findings highlight the existence of an important research gap on the dynamics of transformation and transduction, and the overall public health implications of horizontal transfer of AMR genes. To further develop this field and improve our ability to control AMR, it is essential that we clarify the structural complexity required to study the dynamics of horizontal gene transfer, which will require cooperation between microbiologists and modellers.

Approximately 20% of the world's population resides in coastal areas at risk of rising sea levels due to climate change. This could lead to severe weather events and ecological impact on critical infrastructure. To combat the effects of water-based environmental forces on the land, hard engineering methods such as seawalls have been utilized. However, a more sustainable solution is emerging in nature-based engineering, which involves growing vegetation. This approach can help extend the lifespan of existing technology and provide climate change adaptation and resilience for coastal and riverine communities. The following paper will review seaweed farms as an advanced nature-based mitigation approach. The paper also outlines the findings of experiments at RWTH Aachen University's hydraulic laboratory. These tests involved using seaweed as a natural solution to dampen waves in a model system to test a hypothesis. One result involving a system with two lines of seaweed revealed 15 percent wave damping. Using seaweed as a nature-based solution, a gentle engineering approach to designing future vegetated protection systems can extend the design life of existing coastal infrastructure. This can also provide protection against climate-induced sea level rise, promote coastal risk mitigation, restore ecosystems, and foster blue bio-economic development.

The chemotactic cytokine fractalkine (FKN, chemokine CX3CL1) has unique properties resulting from the combination of chemoattractants and adhesion molecules. The soluble form (sFKN) has chemotactic properties and potently attracts T cells and monocytes. The membrane-bound form (mFKN) facilitates diapedesis and is responsible for cell-to-cell adhesion, especially by promoting the strong adhesion of leukocytes (monocytes) to activated endothelial cells with the subsequent formation of an extracellular matrix and angiogenesis. FKN signaling occurs via CX3CR1, which is the only known member of the CX3C chemokine receptor subfamily. Signaling within the FKN-CX3CR1 axis plays an important role in many processes related to inflammation and the immune response, which often occur simultaneously and overlap. FKN is strongly upregulated by hypoxia and/or inflammation-induced inflammatory cytokine secretion, and it may act locally as a key angiogenic factor in the highly hypoxic tumor microenvironment. The importance of the FKN/CX3CR1 signaling pathway in tumorigenesis and cancer metastasis results from its influence on cell adhesion, apoptosis and cell migration. This review presents the role of the FKN signaling pathway in the context of angiogenesis in inflammation and cancer. The mechanisms determining the pro- or anti-tumor effects are presented, which are the cause of the seemingly contradictory results that create confusion regarding the therapeutic goals.

This study explores the Experience Economy dimensions within fishing tourism, adopting a data science perspective by employing web crawling for extensive data gathering on reviewer profiles from TripAdvisor. Utilizing Natural Language Processing (NLP) techniques, it scrutinizes the relationship between Experience Economy dimensions and user profiling aspects. Findings reveal "Entertainment" as the predominant dimension in tourist reviews, followed by "Aesthetic," "Educational," and "Escapist." Particularly notable are the frequent co-occurrences of "Entertainment"-"Aesthetic" and "Educational"-"Entertainment" pairs. The practical implications underscore the potential socioeconomic benefits of fishing tourism for local communities and fishermen, emphasizing the necessity for governmental support in terms of infrastructure, leadership, legislation, and financial backing to foster sustainable development in this sector. Notably, this research stands as a pioneering effort in its focus on Experience Economy dimensions and user profiling within the context of fishing tourism, drawing data from business pages and user profiles.

Regeneration of lost tail is of great importance to lizards. Anolis carolinensis, a green lizard, is capable of regenerating its tail efficiently after autotomy. Hence, it is considered as a model organism in regeneration study. A. carolinensis shed its tail in order to distract the predator’s attention and thus makes a way to escape. Restoring of the amputated tail takes several days and the mechanism is currently clearly understood. Although save its life, tail regeneration is associated with the impairment of several vital functions in Anoles. In addition, various differences have been observed between original and regenerated tail in terms of mechanism and structure. To date, very little work has been conducted on tail autotomy and regeneration at molecular and genetic level. The genes responsible for regeneration in anoles are identified recently. These genes are evolutionarily conserved through all tetrapod vertebrates. They are, however, in a state of ‘switched-off’ in other vertebrates including humans. Consequently, a throughout study of these so called ‘switched-off’ genes may provide a way of restoring lost organs in human, and thus could revolutionize the modern medical science.

Black spot disease is associated with the breakdown of chitin by chitinolytic bacteria resulting in extensive black lesions across the body of crustaceans. Black spot is prevalent across most fished crustaceans worldwide. Severely infected individuals are rejected from the fishery resulting in financial loss to both fisher’s and seafood export and processing companies. Ecologically, populations with high infection rates may have increased mortalities resulting in fewer individuals surviving the population. The prevalence and severity of shell disease in the edible crab, Cancer pagurus, of various size classes, was assessed via scaled images taken from crabs sampled within the Berwickshire Marine Reserve, UK. A total of 22.4% of individuals across all size groups were found to contain black spot lesions. Male crabs were more commonly affected (26.21%), with more body parts showing lesions and a greater overall blackspot coverage (1.75%) than females (16.43% and 1% respectively). Crabs under the MLS (140mm) showed a significantly higher black spot coverage, but size did not significantly affect infection rates. Carapace and chelae were the most commonly affected areas. Compared to previous studies the Berwickshire Marine Reserve has a relatively low prevalence of black spot disease in Cancer pagurus.

The current energy policy recommends the idea of energy efficiency over fossil energy as a primary matter for the coming years. The kingdom of Morocco requires restructuring of its power equipment by increasing the percentage of renewable energy supplies, optimizing their systems and power storage. Therefore, increasing energy efficiency is an as important obligation as reducing the overall energy consumption. The purpose of this research is to present the energy transition in Morocco towards renewable energies and to assess the diversity of available marine natural resources. Recent research in conversion of ocean thermal energy, wave energy, tidal energy, offshore wind energy, and osmotic energy into power supply has started to encourage different technologies. This research has led to commercial deployment in some cases such as our 550 km long Mediterranean coast and 3000 km long Atlantic. This does not only result in fossil energies independency but also provides advantages like less cost and no pollution.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

Immune checkpoint inhibitors (ICI) are a promising form of immunotherapy that has significantly changed the therapeutic landscape for many advanced cancers. They have shown unique clinical benefit against a broad range of tumour types and a strong overall impact on survival in studied patient populations. However, there are still many limitations holding back this immunotherapy from reaching its full potential as a possible curative option for advanced cancer patients. A great deal of research is being undertaken in the hope of driving advancements in this area, building a better understanding of the mechanisms behind immune checkpoint inhibition and ultimately developing more effective, safer, and wider-reaching agents. Taking into account the current literature on this topic, this review aims to explore in depth the basis of the use of ICIs in the treatment of advanced cancers, evaluate its efficacy and safety, consider its current limitations, and finally reflect on what the future holds for this very promising form of cancer immunotherapy.

Outbreaks of the crown-of-thorns seastar (CoTS) represent a major cause of coral loss on the Great Barrier Reef. Outbreaks might be explained by enhanced larval survival supported by higher phytoplankton availability after flood events, yet little is known about CoTS larvae feeding behaviour, in particular their potential for selective feeding. Here, single- and mixed-species feeding experiments were conducted on CoTS bipinnaria larvae using five algae (Phaeodactylum tricornutum, Pavlova lutheri, Tisochrysis lutea , Dunaliella sp. and Chaetoceros sp.) and two algal concentrations (1000 and 2500 algae mL^-1). Cell counts using flow-cytometry at the beginning and end of each incubation experiment allowed us to calculate the filtration and ingestion rates of each species by CoTS larvae. In line with previous studies, CoTS larvae ingested more algae when initial algal concentration was higher. We found evidence for the selective ingestion of some species (Chaetoceros sp., Dunaliella sp.) over others (P. lutheri, P. tricornutum). The preferred algal species had the highest energy content, suggesting that CoTS selectively ingested the most energetic algae. Ultimately, combining these results with spatio-temporal patterns in phytoplankton communities will help elucidate the role of larval feeding behaviour in determining the frequency and magnitude of CoTS outbreaks.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

The River Habitat Survey (RHS) is a method for assessing the conditions of a river channel and valley, taking into account hydromorphological factors, and assessing the degree of naturalness or the degree of anthropogenic alteration within the channel and valley based on physical and landscape data. The hypothesis tested in this study was that the quality of river habitats demonstrated using the RHS should translate into the composition of their fauna. We investigated aquatic bugs (Heteroptera Aquatica), which are a group with considerable dispersal abilities and, at the same time, composed of stenotopic species associated with a particular environment as well as of eurytopic elements inhabiting a wide range of environments (REF). The research was carried out in a small lowland river, the River Krąpiel (north-western Poland) at 6 sites with 43 sub-sites included. Our analyses suggest the RHS method can predict the composition and quality of the aquatic bug fauna inhabiting a given river. Indicators of river habitat quality (HQA and RHQ) will be associated with different habitat types depending on the geographic location and type of river, once indicating habitats associated with the mainstream river and mineral substrate (mountain and small lowland rivers) and at other times habitats covered by vegetation with relatively slow water flow (large and medium lowland rivers). Therefore, RHS may be a good method for estimating the water bug fauna, linking it to the size and character of the river.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

The protection and regulation of international trade of Australia’s native species is legislated by its Environment Protection and Biodiversity Conservation Act of 1999. In response to overwhelming evidence that the Act is ineffective at protecting biodiversity, the Australian Government is currently reforming its environmental laws. One problematic component of the Act is in cases where threatened species interact with multiple regulatory and management frameworks, such as commercially fished marine species that are traded as seafood. Here, we analyzed international seafood trade data and found that Australia exports four threatened fish species listed under the Act and additional species acknowledged as globally threatened. In light of our analysis, we have three recommendations for Australia’s new environmental legislation: 1) apply the same precautions to commercially harvested species as to other threatened species; 2) review the status of all threatened species annually; and 3) assess species listed on global conservation conventions. These recommendations will help ensure that Australia’s marine biodiversity is protected, despite its commercial value.

In reinforced concrete (RC) structures, splicing is required owing to the length limitations of rebars, insufficient lengths, and transportation issues. In particular, splices connect the rebar of RC structures such as walls, columns, beams, slabs, and joints. Lap splices are the most commonly used method worldwide because they do not require specific equipment or skilled workers. However, lap splices incur high construction costs because of the long splice lengths required for large-diameter rebars in megastructures, as well as issues pertaining to material supply, labor costs, constructability, and project duration. Additionally, approximately 15% more rebar is required because of the overlap. Energy saving for a sustainable built environment is possible if the disadvantage of lap splices, which generate high CO2 emissions due to the excessive use of rebar, are resolved. Hence, mechanical rebar couplers (MRCs) have been developed. However, despite their advantages, they have not been widely applied in construction sites owing to concerns regarding safety, quality, and constructability. Although various MRCs have been developed, most studies focus only on their structural performance. Therefore, a data-driven approach for selecting MRCs based on the reinforcing bar shape and structural characteristics is proposed in this study. Using a data-driven MRC selection algorithm, using the T-threaded coupler for one rebar over two floors resulted in 56% more efficient labor productivity, 15% shorter assembly time, 17% lower costs, and 26% lower CO2 emission. Using a developed algorithm, the appropriate MRC can easily and rapidly be selected for frequent design changes.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

The emergence of pathogenic fungi is a major and rapidly growing problem (7% increase) that affects human and animal health, ecosystems, food security and the economy worldwide. The Dermocystida group in particular has emerged relatively recently and includes species that affect both humans and animals. Within this group, one species in particular, Sphareothecum destruens, also known as the Rosette agent, represents a major risk to global aquatic biodiversity and aquaculture and has caused severe declines in wild fish populations in Europe and large losses in salmon farms in the USA. It is a species that has been associated with a healthy carrier for millions of years but the host has managed in recent decades to invade parts of Southeast Asia, Central Asia, Europe and North Africa. In order to better understand the emergence of this new disease, we have for the first time synthesised current knowledge on the distribution, detection, prevalence of S. destruens as well as the associated mortality curves, and the potential economic impact in countries where the healthy carrier has been introduced. Finally, we propose solutions and perspectives to manage and mitigate the emergence of this fungus in countries where it has been introduced.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The intestinal microbial community of aquatic animals is closely related to the environment and thus affects the health of aquatic animals. Here we investigated annual variation of intestinal bacteria community structures of Ruditapes philippinarum cultured using two different methods, bottom sown and raft hanging. Bacterial diversity of seawater and sediment in different seasons was examined as well. Correlation between R. philippinarum intestinal bacteria community structures and environmental factors was analyzed. The results showed that in the two aquculture areas where R. philippinarum was differentially cultured, bacteria community structure of seawater and sediment both altered with seasons. However, neither seasonal changes nor difference in culture methods could significantly affect the intestinal bacteria community structures of R. philippinarum. Additionally, in terms of the alpha diversity of intestinal bacteria communities, there was no significant difference in R. philippinarum cultured using the two methods. For benthic cultured clams, alpha diversity of the intestinal bacterial communities was often higher than that of the environmental bacterial communities. For raft hanging cultured calms, Alpha diversity of the intestinal bacterial communities was normally comparable with that of the environmental counterparts. Beta diversity analysis showed that the intestinal bacterial community structure of R. philippinarum was mainly determined by both deterministic and stochastic processes. Correlation analysis showed that the intestinal bacterial community structures of R. philippinarum were determined by a variety of environmental factors. For clams collected from the benthic culture area, the intestinal bacterial structure was more correlated with the physicochemical properties of sediment in comparing with those of seawater. For clams collected from the raft-culture area, the intestinal bacterial structure was mainly determined by the phsicochemical characteristics of seawater. This study helps us to better understand the bacterial community structure in complex aquaculture ecosystems, providing a reference for healthy shellfish aquaculture and ecosystem protection in aquaculture area.

JBIR-99 is a secondary metabolite of marine fungi that has been shown to possess strong antibiotic activity. An efficient approach using a combination of size exclusion chromatography with a Sephadex LH-20 and high-speed counter-current chromatography (HSCCC) has been successfully developed for the isolation and purification of a polyketide from the solid-state fermentation of Meyerozyma guilliermondii. The active compound was isolated with purity >95% by HSCCC using an optimized solvent system composed of petroleum ether–ethyl acetate– 95% ethanol–water (5:3:5:3, v/v/v/v) after size exclusion chromatography. This compound was successfully purified in the quantity of 68 mg from 120 mg of the crude extract. The structure of JBIR-99 was elucidated and assigned by 1D, 2D NMR spectroscopic, and positive HRESITOFMS. Moreover, the relative configuration of compound JBIR-99, displaying a quite complex multi-ring structure, is determined by X-ray crystallography for the first time. The purification method developed for JBIR-99 will facilitate the further investigation and development of this antibiotic agent as a lead compound. Furthermore, it is suggested that the combination of size exclusion chromatography and HSCCC could be more widely applied for the isolation and purification of polyketides from marine fungi.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

Introduction Livestock abortigenic agents, which are microorganisms that lead to premature foetal death and expulsion before completion of the gestation period, are common in Africa and Asia. Abortion events cause economic losses by lowering reproduction (and hence herd/flock sizes) and effects on milk production. Despite the importance of livestock production for food security and livelihoods of millions of the world’s poorest communities, very little is known about the scale, magnitude or causes of livestock abortion in Africa. The aim of this review was to determine the current status of the burden of livestock abortion and surveillance measures adopted for livestock abortigenic pathogens in Africa and Asia, and to explore feasible surveillance technologies. Methodology A systematic literature search was conducted using Preferred Reporting of Systematic Reviews and Meta-analyses (PRISMA) guidelines in four databases for studies published between 1 Jan 1990 and 31 July 2021 that reported epidemiological surveys of livestock abortigenic pathogens in cattle, goats and sheep in Africa and Asia including; Brucella spp., Neospora caninum, Toxoplasma gondii, Rift valley fever virus, Coxiella burnetii, Chlamydia, Leptospira and Bovine viral Diarrhoea Virus. A meta-analysis was used to estimate the species-specific prevalence of the abortigenic diseases and the region where they were detected. Results In the systematic literature search, 48 full papers were included which in total included 50 species-specific surveillance reports from Africa and 19 from Asia. Adjusted median seroprevalence calculations estimated Brucella at 6.85% (range 1.2-11.6) of 9071 sheep, 3.35% (range 0.90-5.40) of 17,007 goats, 8.95% (range 0.50-63.60) of 171,733 cattle, Neospora at 6.80% (range 6.80 -6.80) of 555 sheep, 10.80 (range 10.80-10.80) of 185 goats, 12.65% (range 3.40- 25.60) of 3775 cattle, Toxoplasma at 27.50% (range 1.40 – 75.90) of 2284 sheep, 32.0% (range 20.00- 64.80) of 1226 goats, 7.50% (range 7.50 - 7.50) of 174 cattle, Coxiella at 9.20 (range 9.20 – 9.20) of 184 sheep, 24.20% (range 24.20-24.20) of 91 goats, 13.80% (range 13.80-13.80) of 217 cattle, Rift valley fever virus at 7.70 (2.40-40.00) of 874 sheep, 20.95 (range 2.50-40.00) of 547 goats, 7.45% (range 3.60-11.30) of 309 cattle, Bovine viral diarrhea virus at 78.90 (range 78.90 – 78.90) of 398 cattle, Leptospira at 70.50 (range 70.50 – 70.50) of 373 cattle and Chlamydia at 6.60 (6.60-6.60) of 803 sheep. We found that most studies, 45 (89%) used serological surveys, 1 (2%) used molecular and 1 (2%) reported to have used Mobile-phone based surveillance approach. Three studies (6.25%) of the 48 included were embedded in the national surveillance programs of the respective countries they were conducted, majority 89% were stand-alone cross-sectional studies. Conclusion In conclusion, livestock abortigenic pathogens are still a burden in many African and Asian countries.

The advent of RNA-sequencing (RNA-Seq) technologies has markedly improved our knowledge and expanded the compendium of small non-coding RNAs, most of which derive from the processing of longer RNA precursors. In this review article, we will discuss about the biogenesis and function of small non-coding RNAs derived from eukaryotic ribosomal RNA (rRNA), called rRNA fragments (rRFs), and their potential role(s) as regulator of gene expression. This relatively new class of ncRNAs remained poorly investigated and underappreciated until recently, due mainly to the a priori exclusion of rRNA sequences—because of their overabundance—from RNA-Seq datasets. The situation surrounding rRFs resembles that of microRNAs (miRNAs), which used to be readily discarded from further analyses, for more than five decades, because we could not believe that RNA of such a short length could bear biological significance. As if we had not yet learned our lesson not to restrain our investigative, scientific mind from challenging widely accepted beliefs or dogmas, and from looking for the hidden treasures in the most unexpected places.

Turning ships in port turning basins is an important and responsible operation, mainly involving the ship itself and the port tugs. Such operations involve many maneuvers that consume a lot of energy (fuel) and emit a lot of emissions. Turning basins in harbors and quay approaches are in most cases relatively shallow. The paper examines the turning of ships in port turning basins using harbor tugs, the effect of shallow depth on ship turning, energy (fuel) consumption and the generation of emissions during such maneuvers of harbor tugs. The paper presents the developed theoretical models, and the experimental results on theoretical models, which were verified on real ships and using calibrated simulators. Discussions and conclusions prepared on the basis of the research base. The use of the developed methodology makes it possible to increase shipping safety, optimize maneuvers and reduce energy (fuel) consumption when turning ships in the port and at the same time reduce the amount of fuel consumed by port tugs and reduce the number of emissions of tugs during such operations.

Thyroid surgery rates have tripled over the past 3 decades making it one of the most frequently performed procedures within general surgery. They are associated with the possibility of serious postoperative complications having a significant impact on the patient's quality of life. The recurrent laryngeal nerve (RLN) palsy and the external branch of the superior laryngeal nerve (EBSLN) palsy are, next to hypoparathyroidism and bleeding after operation, one of the most common complications. The introduction of neuromonitoring into thyroid surgery, enabling both confirmation of anatomical integrity and assessment of laryngeal nerve function, was a milestone that has begun a new era in thyroid surgery. The International Neural Monitoring Study Group made standardization of the technique of RLN and EBSLN monitoring during thyroid and parathyroid surgery which increased prevalence of neural monitoring during thyroidectomy. Current status of IONM and benefits of its use have been presented in this publication.

The gastrointestinal tract is colonized by trillions of different microorganisms, named the gut microbiota, which is key to degrade undigested food such as dietary fibers. The fermentation of these food components leads to the production of short-chain fatty acids (SCFA) acetate, propionate, and butyrate, which exploit several beneficial roles for the host’s health. Their production and absorption happen in different ways in the human intestine and depend on the type of dietary fiber reaching the gut and the microorganisms involved in the fermentation. The supplementation of SCFAs, mostly butyrate, in treating gastrointestinal, metabolic, cardiovascular, and gut-brain-related diseases has been reported in the medical literature. This review aims to give an overview of the production and absorption dynamics of acetate, propionate, and butyrate in the human gut, with a final focus on the role played by these SCFAs on gastrointestinal and metabolic health and the present therapeutic implications.

Fibrodysplasia Ossificans Progressiva (FOP) is an enigmatic, ultra-rare genetic disorder characterized by progressive heterotopic ossification, wherein soft connective tissues undergo pathological transformation into bone structures. This incapacitating process severely limits patient mobility and poses formidable challenges for therapeutic intervention. Predominantly caused by missense mutations in the ACVR1 gene, the disorder has hitherto defied comprehensive mechanistic understanding and effective treatment paradigms. This write-up offers a comprehensive overview of the contemporary understanding of FOP's complex pathobiology, underscored by advances in molecular genetics and proteomic studies. We shed light on targeted therapy, spanning genetic therapeutics, enzymatic and transcriptional modulation, stem cell therapies, and innovative immunotherapies. We also focused on the intricate complexities surrounding clinical trial design for ultra-rare disorders like FOP, addressing fundamental statistical limitations, ethical conundrums, and methodological advancements essential for the success of interventional studies. We advocate for the adoption of a multi-disciplinary approach that converges bench-to-bedside research, clinical expertise, and ethical considerations to tackle the challenges of ultra-rare diseases like FOP and comparable ultra-rare diseases. Overall, this article serves a dual role: as a definitive scientific resource for ongoing and future FOP research and as a call to action for innovative solutions to address methodological and ethical challenges that impede progress in the broader field of medical research for ultra-rare conditions.

Keywords: Marine Coasts; Protected Areas; Defense and Conservation; Asbestos Cement Materials; Wastes; Contamination; Human Health Risk; Medical Geology.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

Mycobacteria can be one of the main contaminants of biological products, and their presence can have serious consequences on patients’ health. Thus, specific testing is necessitated by regulations such as the European Pharmacopoeia. The current pharmacopeial reference i.e., microbial culture method cannot ensure an exhaustive detection of mycobacteria due to their growth characteristics. Additionally, the method is time-consuming and requires a continuous supply of culture media, which could be further challenging. Thus, to overcome these challenges, pharmaceutical industries need to consider alternative non-microbiological techniques to detect these fastidious, slow-growing contaminating agents. This review provides an overview of alternative methods, which could be applied within a quality control environment of biological products, and underlines advantages and limitations of these methods. Nucleic acid amplification techniques or direct measurement of mycobacteria stands out as the most suitable alternatives for mycobacterial testing in biological products.

New research points to a possible link between Autism Spectrum Disorder and the gut microbiota as many autistic children have co-occurring gastrointestinal problems. This review focuses on specific alterations of gut microbiota mostly observed in autistic patients. Particularly, the mechanisms through which such alterations may trigger the production of the bacterial metabolites or leaky gut in autistic people are described. Various altered metabolite levels were observed in autistic children, many of those were of bacterial origin such as short chain fatty acids (SCFAs), indoles and lipopolysaccharides. A less integrative gut-blood-barrier is abundant in autistic individuals. This explains the leakage of bacterial metabolites into the patients triggering new body responses or altered metabolism. Some other co-occurring symptoms such as mitochondrial dysfunction, oxidative stress in the cells, altered tight junctions in the blood brain barrier and structural changes in cortex, hippocampus, amygdala and cerebellum were detected. Moreover, this paper suggests that autism is associated with an unbalanced gut microbiota (dysbiosis). Although the cause-effect relationship between autism and gut microbiota is not yet well established, consumption of specific probiotics may represent a powerful tool to re-establish gut homeostasis and promote gut health. Diagnostic and therapeutic value of new biomarkers leading to the perturbation in the phenylalanine metabolism will be discussed.

Full-scale wind turbine technology has been widely developing in the recent years and condition monitoring techniques assist at the scope of making 100\% technical availability a realistic perspective. In this context, several retrofitting techniques are being used for further improving the efficiency of wind kinetic energy conversion. This kind of interventions is costly and, furthermore, the estimation of the energy enhancement is commonly provided under the hypothesis of ideal conditions, as for example absence of wakes between nearby turbines. A precise quantification of the energy gained by retrofitting is therefore precious in real conditions, that can be very different from ideal ones. In this work, three kinds of retrofitting are studied through the operational data of test case wind farms: improved start-up through pitch angle adjustment near the cut-in, aerodynamic blade retrofitting by means of vortex generators and passive flow control devices, extension of the power curve by raising cut-out and high wind speed cut-in. SCADA data are employed and reliable methods are formulated for estimating the energy improvement from each of the above retrofitting. Further, an insight is provided about wind turbine functioning under very stressing regimes, as for example high wind speeds.

Thermaikos Gulf (TG) is a semi-enclosed, river-influenced, marine system situated in the eastern Mediterranean Sea, sustaining both urban coastal regions and ecologically preserved natural areas. Facing a plethora of environmental and anthropogenic pressures, the TG serves as a critical nexus where human activities intersect with marine ecosystems. The second largest city of Greece, Thessaloniki, is located in the northern part of the gulf, while a large environmentally protected zone with multiple river deltas is lying along its western coasts. The quality and health of the TG’s marine environment are tightly linked to the socioeconomic activities of the coastal communities comprising approximately 1.5 million inhabitants. The main features of TG’s environmental dynamics and ecological status have been scrutinized by dedicated research endeavours during the last 50 years. This review synthesizes the seminal findings of these investigations, offering an evaluation of their contribution to research, their present collective impact, and their trajectory toward the future. A severe deterioration of the TG’s environmental quality was detected in the 1970s and 1980s when treatment of urban wastewater was completely absent. A steady trend of recovery was observed after the 1990s, however without achieving, so far, the goal of a “good environmental state”, mandated by national legislation and European directives. The most important research gaps and uncertainties are also discussed and specific recommendations for the improvement of monitoring and understanding about the physical, biochemical, and ecological state of the gulf are provided. The most significant discrepancy is related to the fragmentary monitoring of the TG in both space (partial coverage) and time (temporal gaps), which has been intensified after 2010 due to the reduced funding for environmental research and protection under the severe Greek economic recession. This review aspires to highlight the importance of bolstering monitoring initiatives that can provide continuous observations and further understanding on the TG's ecological and physicochemical conditions. Targeted recommendations, aimed at ameliorating the fragmented monitoring processes, are also provided, advocating for a holistic approach that can safeguard the ecological integrity of the Thermaikos Gulf and uphold its role as a crucial link to marine biodiversity and sustainability in the Mediterranean basin.

The influenza virus has been the primary cause of the pandemic, posing a constant threat to human society. Due to its genetic evolution and continuous outbreak, antiviral research currently focuses on exploring a novel lead agent. A comprehensive antiviral screening discovered a marine bacterium whose extract exerted excellent efficacy against influenza viruses. Parerythrobacter sp. M20A3S10, a novel strain under the family Erythrobacteraceae, could produce carotenoids exhibiting antiviral and anticancer activity by enhancing the cellular immune system. Post-treatment of M20A3S10 extract showed outstanding therapeutic indexes: against influenza virus A/PR8 (H1N1) [selectivity index (SI) = 24.0], A/Wisconsin/15/2009 (H3N2) (SI = 30.1) and B/Florida/78/2015 (SI = 38.2). Comparably, the effectiveness was demonstrated against Zika virus (ZIKV) and dengue virus type 2 (DENV2) with an SI of 22.5 and 24.1, respectively, namely broad-spectrum activity. Of note, the antiviral responses resulted from the common replication mechanism between IAV, ZIKV, and DENV2. The stimulation of apoptosis-mediated cellular immunity prevented the viral release and protected the host, suggesting that switching from necroptosis to apoptosis is a novel antiviral target. Although the specific compound affecting the antiviral activity was not identified, its promising efficacy with broad activity will contribute to developing a strategy for preventing future pandemics.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Number of studies claim that tobacco control (TC) regulations are associated with reductions in smoking-related hospitalisation rates, however very few have estimated the impact of TC laws (TCL) at both countrywide and regional levels, and none of them - in relation to compliance with TC regulations. This study evaluates the effects of Russian TCL on hospital admission (HA) rates for pneumonia countrywide and in 10 Russian regions and the extent of these effects in connection with the compliance to TCL. Methods: HA rates for pneumonia during 2005–2019 were analysed to compare the periods before and after the adoption of TCL in 2013. An interrupted time series design and a Poisson regression model were used to estimate the immediate and long-term effects of TCL on pneumonia annual hospitalisation rates after the TCL adoption, compared with the pre-law period. The 10 Russian regions were compared using the TCL Implementation Scale (TCIS) developed on the basis of the results of Russian TC policy evaluation survey; Spearman’s rank correlation and linear regression models were employed. Results showed a 14.3% reduction in HA rates for pneumonia (RR 0.88; p=0.01) after the adoption of TCL in Russia with significant long-term effect after 2013 (RR 0.86; p=0.006). Regions with better enforcement of TCL exhibited greater reductions in pneumonia HA rates (rsp=−0.55; p=0.04); (=−4.21; p=0.02). Conclusions: TCL resulted in a sustained reduction in pneumonia hospitalisation rates, but these effects, varying by region, may depend on the scale of the TCL enforcement.

This paper addresses the conceptual exploration of various issues that form an integral part of the ethical dimensions surrounding the use of artificial intelligence (AI) in the field of marketing. We critically review some of the main ethical challenges AI poses to humanity: privacy, data security, bias, transparency, and accountability. Therefore, we will discuss the delicate balance between exploiting the transformation potential of AI for personally designed marketing strategies and ethical imperatives to safeguard the rights of consumers to retain trust. Then, the present regulatory landscape responding to these ethical challenges will be assessed by building on effective regulation, like the GDPR, existing proposed legislative frameworks, and industry guidelines. To underscore the role of an ongoing dialogue between marketers, technologists, ethicists, and regulators for developing a responsible AI ecosystem in marketing. Further, strategic recommendations for implementing company-based ethical AI marketing practices. The further strong guidelines provide enhancement transparency to consumers and investment in research to remove biases from algorithms. It also underscores principal scopes of further research and development, focusing on the need for new-age solutions to guide the ethical quagmires that AI-led marketing throws up. We suggest that integration should be done proactively and collaboratively. Thus, if attention is paid more to ethics and multidisciplinary dialogue, only such hyperbolic promises can be realized by AI-driven marketing. There are such promises through which AI-driven marketing will meet business goals and be huge at societies' values.

Natural language Processing (NLP) has significantly transformed in the last decade, especially in the field of Language Modeling. Large Language Models (LLMs) have achieved SOTA performances on Natural Language Understanding (NLU) and Natural Language Generation (NLG) tasks by learning language representation in self-supervised ways. This paper provides a comprehensive survey to capture the progression of advances in Language Models. In this paper, we examine the different aspects of Language Models, which started with a few million parameters but have reached the size of a trillion in a very short time. We also look at how these LLMs transitioned from task-specific to task-independent to task-and-language-independent architectures. This paper extensively discusses different pre-training objectives, benchmarks, and transfer learning methods used in LLMs. It also examines different fine-tuning and In-Context learning techniques used in downstream tasks. It also explores how LLMs can perform well across many domains and datasets if sufficiently trained on a large and diverse dataset. Next, it discusses how, over time, the availability of cheap computational power and large datasets have improved LLM’s capabilities and raised new challenges. As part of our study, we also inspect LLMs from the lens of scalability to see how their performance is affected by the model’s depth, width, and data size. Lastly, we provide an empirical comparison of existing trends and techniques and a comprehensive analysis of where the field of LLM currently stand.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Hip joint surgeries, including total hip replacement or resurfacing, have increased tremendously in the last decades. Number of patients of all ages, replace their hip, due to severe injuries or trauma problems, so as to have a better life. According to these factors, new material and processes in implants manufacturing are imported to medicine, through research programs, every year. In the scope of one of these programs, that has to do with ceramic coatings on metallic resurfacing implants, a new 3axis Hip simulator was designed and manufactured in the Laboratory of Manufacturing Technology of the National Technical University of Athens. The scope of this paper is to present the main parts, materials and process used to manufacture the simulator as well as the way the simulator is working and how its movement in 3axis is accomplished. Furthermore, the evaluation of the machine and its use to examine resurfacing implants is presented.

From oxidative eustress and distress, to bioenergetic metabolism, and cell death, the reactive species interactome (RSI) and mitochondria are two connected metabolisms that require further investigation improving redox medicine. The step before, finding new clues needs a comprehensive discussion of the two metabolisms, and their relationship. Here, the review focuses on the RSI-mitochondria axis, from mitochondrial roles to crosstalk between mitochondria and other organelles, and the major implication of the RSI in mitochondrial roles. Specifically, the review discussed the apoptosis-necroptosis-ferroptosis death traingle, mitochondrial protein quality control system, calcium homeostasis, and mitochondrial metabolome. Through mitochondrial diseases, and mitochondrial dysfunction associated with diseases, the RSI-mitochondria axis is proposed as a brand-new perspective, including with the involvement of bacterial microbiota, on redox signaling, and redox medicine.

The PI3K-AKT-mTOR signal transduction pathway regulates a variety of biological processes including cell growth, cell cycle progression and proliferation, cellular metabolism and cytoskeleton reorganization. Fine-tuning of the PI3K pathway signaling output is essential for the maintenance of tissue homeostasis and uncontrolled activation of this cascade leads to a number of human pathologies including cancer. Inactivation of the tumour suppressor phosphatase PTEN and/or activating mutations in the proto-typical lipid kinase PI3K have emerged as some of the most frequent events associated with human cancer and as a result the PI3K pathway has become a highly sought-after target for cancer therapies. In this review we summarize the essential role of the PTEN-PI3K axis in controlling cellular behaviors by modulating activation of key proto-oncogenic molecular nodes and functional targets. Further, we highlight important functional redundancies and peculiarities of these two critical enzymes that over the last few decades have become a central part of the cancer research field and have instructed hundreds of pre-clinical and clinical trials to better cancer treatments.

Systemic inflammation and coronary microvascular endothelial dysfunction are essential pathophysiological factors in heart failure with preserved ejection fraction (HFpEF) that support the use of statins. The pleiotropic properties of statins, such as anti-inflammatory, antihypertrophic, antifibrotic, and antioxidant effects, are generally accepted and may be beneficial in HF, especially in HFpEF. Numerous observational clinical trials have consistently shown a beneficial prognostic effect of statins in patients with HFpEF, while the results of two larger trials in patients with HFrEF have been controversial. Such differences may be related to a more pronounced impact of the pleiotropic properties of statins on the pathophysiology of HFpEF and pro-inflammatory comorbidities (arterial hypertension, diabetes mellitus, obesity, chronic kidney disease) that are more common in HFpEF. This review discusses the potential mechanisms of statin action that may be beneficial for patients with HFpEF, as well as clinical trials that have evaluated the statin effects on left ventricular diastolic function and clinical outcomes in patients with HFpEF.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

Bacteria can colonize and develop biofilm on a large variety of biotic and abiotic materials, it is accountable for nosocomial infections and chronic illness and consequently, it is a serious economic and public health problem. Staphylococcus epidermidis, thanks to its ability to form biofilm and colonize biomaterials, represents the most frequent causative agent involved in bio-film-associated infections of medical devices. Due to the biofilm presence, S. epidermidis infections are extremely difficult to treat and the research of new molecules able to interfere with its biofilm formation has a remarkable interest. In the present work, the attention was focused on Pseudomonas sp. TAE6080, an Antarctic marine bacterium able to produce and secrete an effective antibiofilm compound. The molecule responsible for this activity was purified by an activity-guided approach and it resulted to be a periplasmic protein, named Cold-Azurin. The Cold-Azurin was recombinantly produced in E. coli and purified. The recombinant protein was able to impair S. epidermidis attachment to the polystyrene surface and effectively prevent biofilm formation.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

The fault diagnosis of safety critical systems such as wind turbine installations includes extremely challenging aspects that motivate the research issues considered in this paper. In fact, the prompt detection and the reliable diagnosis of faults in their earlier occurrence represent the key point especially for offshore installations. For these plants, operation and maintenance procedures in harsh environments would inevitably increase the cost of the energy production. Therefore, this work investigates fault diagnosis solutions that are considered in a viable way and used as advanced techniques for condition monitoring of dynamic processes. To this end, the work proposes the design of fault diagnosis strategies that exploit the estimation of the fault by means of data--driven approaches. This solution leads to the development of effective methods allowing the management of partially unknown information of the system dynamics, while coping with measurement errors, the model--reality mismatch and other disturbance effects. In mode detail, the proposed data--driven methodologies exploit fuzzy systems and neural networks in order to estimate the nonlinear dynamic relations between the input and output measurements of the considered process and the faults. To this end, the fuzzy and neural network structures are integrated with auto--regressive with exogenous input descriptions, thus making them able to approximate unknown nonlinear dynamic functions with arbitrary degree of accuracy. Once these models are estimated from the input and output data measurement acquired from the considered dynamic process, the capabilities of their fault diagnosis capabilities are validated by using a high--fidelity benchmark that simulates the healthy and the faulty behaviour of a wind turbine system. Moreover, at this stage the benchmark is also useful to analyse the robustness and the reliability characteristics of the developed tools in the presence of model--reality mismatch and modelling error effects featured by the wind turbine simulator. On the other hand, a hardware--in--the--loop tool is finally implemented for testing and comparing the performance of the developed fault diagnosis strategies in a more realistic environment and with respect to different fault diagnosis approaches.

Pediatric onset multiple sclerosis (POMS), characterized by the onset of multiple sclerosis before the age of 18, is gaining increased recognition. Approximately 5 percent of MS cases manifest before the age of 18, with less than 1 percent occurring before the age of 10. Despite its rarity, pediatric MS exhibits distinct characteristics, with an association between younger age at onset and a comparatively slower disease progression. Despite this slower progression, individuals with POMS historically reach disability milestones at earlier ages than those with adult-onset multiple sclerosis. While various immunomodulatory agents demonstrate significant benefits in MS treatment, such as reduced relapse rates and slower accumulation of brain lesions on magnetic resonance imaging (MRI), the majority of disease-modifying therapies (DMTs) commonly used in adult MS lack evaluation through pediatric clinical trials. Current evidence is predominantly derived from observational studies. This comprehensive review aims to consolidate existing knowledge on the mechanisms of action, efficacy, safety profiles, and recommended dosages of available DMTs specifically in the context of pediatric MS. Furthermore, the review outlines recent advancements and explores potential medications still in developmental stages, providing a thorough overview of the current landscape and future prospects for treating POMS.