The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

Rice blast and brown planthopper (BPH) are two of the most destructive diseases and pests in rice (Oryza sativa L.) production in China. The development of multi-resistant varieties is widely recognized as the most efficient and environmentally friendly approach to controlling crop diseases and pests. Functional molecular markers (FMMs) have been developed from functional variants in the genic region associated with trait variation, greatly enhancing the efficiency of identifying and pyramiding valuable genes in crop breeding. In this study, two FMMs and a multiplex PCR amplification system were developed for two major broad-spectrum BPH resistance genes, Bph6 and Bph9. By assistance of FMMs in multi-resistant rice restorer line development pipeline, two lines (Huahui7713 and Huahui3006) with blast and BPH resistance were developed by pyramiding three resistance genes Pigm, Bph6 and Bph9. Huahui7713 and Huahui3006 as male lines, two new hybrid rice varieties (WeiLiangYou7713 and Xuanliangyou3006) were certificated and commercial released in China. WeiLiangYou7713 and Xuanliangyou3006 showed improved blast and BPH resistance, and no penalty on yield and grain-quality. Annual promotion area of WeiLiangYou7713 has exceeded 53.3 thousand hectares, indicating its widespread adoption and success in the market. Huahui7713 and Huahui3006 could have great potential for utilization in blast and BPH resistance rice breeding.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

This paper aims to demonstrate how the detection of communities for epidemiological networks can be used to reduce the dimensionality of optimal control problems. A range of planted partition stochastic blockmodels are generated, where the underlying communities in the model vary in detectability. A high-performance computing workflow is then used to simulate and estimate reduced model dynamics for the networks, which in turn is used to find optimal control solutions.

In this paper, the power quality of interconnected microgrids is managed using a Model Predictive Control (MPC) methodology which manipulates the power converters of the microgrids in order to achieve the requirements. The control algorithm is developed for the microgrids working modes: grid-connected, islanded and interconnected. The results and simulations are also applied to the transition between the different working modes. In order to show the potential of the control algorithm, a comparison study is carried out with classical Proportional-Integral Pulse Width Modulation (PI-PWM) based controllers. The proposed control algorithm not only improves the transient response in comparison with classical methods but also shows an optimal behavior in all the working modes, minimizing the harmonics content in current and voltage even with the presence of non-balanced and non-harmonic-free three-phase voltage and current systems

The goal of this contribution is an application of the Linear General Model Predictive Control (LGMPC). In this paper, stability of the LGMPC is proven by means of a demonstration of a Theorem stating a sufficient and constructive condition. This condition can be applied for calculating the weight matrices of the cost function in the optimisation problem in LGMPC. Lower bounds conditions are found for one of these matrices and then a system with saturation is taken into consideration. The conditions could be interpreted and discussions through physical aspects. The obtained results were tested by means of computer simulations and an example with a recover water process is considered.

A proportion of osteoarthritis (OA) patients are unsatisfied with post-operative outcomes following total joint replacement surgery (TJR), with insufficient pain relief or poor functional improvement. Predicting those will have poor outcomes would be beneficial for patients and clinicians. The aim of this study was to determine the relationship between baseline anthropometric data and the concentration of pre-operative serum and peri-operative synovial fluid (SF) cytokines with 7-month post-operative outcomes in a cohort of knee and hip OA patients. 160 OA patients were recruited who were scheduled for TJR. The concentration of 24 cytokines were measured in blood and SF by multiplex assay. EQ5Dindex health status was assessed pre-operatively and at 7-months post-operatively. 13% of patients were identified as non-responders based on EQ5Dindex. Compared to responders, non-responders were of higher BMI, had greater waist and hip circumference and had higher levels of SF leptin but lower levels of SF Resistin (p<0.05). Linear regression analysis found a significant relationship between pre-operative body weight and post-operative response (ΔEQ5Dindex; r=0.222, p=0.049). The combination of body weight with SF amphiregulin and SF IL-6 provided an improved predictive model of post-operative response (r=0.470, p=0.035).

Alzheimer’s disease (AD) predominantly occurs as a late-onset form (LOAD), involving neurodegeneration and cognitive decline with progressive memory loss. Over time, risk factors and aging promote accumulation of well-known AD hallmarks in oxidative stress, amyloid-beta and tau protein pathology, as well as inflammation. Homeostatic glial functions regulate and suppress these AD hallmarks; however, other glial states involve increased pro-inflammatory cytokine release and further hallmark accumulation. Different stresses can additionally induce cellular senescence, or an irreversible differentiation process resulting in decreased supportive functions and increased, pro-inflammatory cytokine release. While these pathophysiological underpinnings all contribute to LOAD, they require temporal and mechanistic integration. This Perspective proposes that traditional AD hallmarks induce glial senescence in LOAD, where sufficient senescent glia exacerbate ongoing AD pathology and primarily drive LOAD into clinical, cognitive decline. We first explore age-related increases in pro-inflammatory glial activity, and then discuss emerging evidence linking oxidative stress, neurons containing tau pathology, and amyloid-beta to microglia, oligodendrocyte progenitor, and astrocyte senescence. Our evidence-based model mainly predicts that senescent astrocytes and oligodendrocyte progenitors together pressure microglia to phagocytose neurons containing tau pathology, where resulting senescent microglia create neuritic plaques and induce paracrine senescence transitioning into and progressing clinical, dementia presentation. This predictive model accounts for why medications used to treat LOAD fail, as previous treatments have not reduced senescent glial burden. It is also coherent with the predominant hypotheses surrounding LOAD involving the amyloid cascade, tau, glia and inflammation, creates testable hypotheses about LOAD, and increases rationale in testing senolytics as targeted treatments for LOAD arrest and reversal.

A contemporary technique for calculating seismic risk is earthquake nowcasting (EN), which analyzes the progression of the earthquake (EQ) cycle in fault systems. 'Natural time' is a novel idea of time that serves as the foundation for EN assessment. The earthquake potential score (EPS), which has been discovered to have useful uses regionally and worldwide, is a unique tool EN uses to predict seismic risk. For the estimation of the EPS for the occurrences with the highest magnitude among these applications, we have since 2021 concentrated on Greece territory, applying sophisticated Artificial Intelligence (AI) algorithms, both wise (semi)supervised and unsupervised models, along with a customized dynamic sliding window technique that performs as a stochastic filter able to fine-tune the geo seismic occurrences. Long short-term memory (LSTM) neural networks, random forests, and clustering (geospatial) models are three machine learning techniques that are particularly good at finding patterns in vast databases and may be used to enhance earthquake prediction performance. In this study, we attempt to forecast whether practical Machine-learning and AI/Game-theoretic-based approaches can help predict big earthquakes and the normal future seismic cycle for 6-12 months. Specifically, we focus on answering two questions for a given region: (1) Is there a chance that a significant earthquake—say, one with a magnitude of M ≥ 6.0 will happen in the upcoming year? (2) What is the largest earthquake magnitude predicted in the upcoming year, and with which exact geographic coordinates (GCS)? Our results are quite promising and project a high precision accuracy score (≥ 98%) for seismic nowcasting in terms of four predictive parameters: the approximate (a) latitude, (b) longitude, (c) focal depth, and (d) magnitude of the phenomena.

The purpose of this paper is to develop a theoretical predictive model for LNG shipping routes selection process. Strategic decisions about shipping costs could be improved if a deeper knowledge about products economic value is provided. Developments made on the extraction and industrial processes related to this fossil fuel are driving the natural gas sector towards a unique globalised market. Moreover, data analytics applications as well as machine learning are topics presented as perfect catalysers for achieving an unprecedented natural gas globalised market. Additionally, this paper aims at showing the state of the art of new techniques used in transportation engineering that might have synergies with other industries (eg. commodities cost reduction, energy supply…). Finally, this paper aims to provide foundation for further research and development using more sophisticated data and algorithms that will help to close the gap between theoretical and practical scope of this techniques.

Predicting human trajectories poses a significant challenge due to the complex interplay of pedestrian behavior, which is influenced by environmental layout and interpersonal dynamics. This complexity is further compounded by variations in scene density. To address this, we introduce a novel dataset from the Festival of Lights in Lyon 2022, characterized by a wide range of densities (0.2-2.2 ped/m2). Our analysis demonstrates that density-based classification of data can significantly enhance the accuracy of predictive algorithms. We propose an innovative two-stage processing approach, surpassing current state-of-the-art methods in performance. Additionally, we utilize a collision-based error metric to better account for collisions in trajectory predictions. Our findings indicate that the effectiveness of this error metric is density-dependent, offering prediction insights. This study not only advances our understanding of human trajectory prediction in dense environments but also presents a methodological framework for integrating density considerations into predictive modeling, thereby improving algorithmic performance and collision avoidance.

This work presents a Fault-Tolerant Model Predictive Control (FTMPC) algorithm applied to a simulation model for sewer networks. The control system will aim to prevent contaminated water from escaping the network, especially during periods of heavy rainfall, that can cause combined sewer overflows (CSO), while maintaining the flow of water towards the wastewater treatment plant (WWTP) as close as possible to its nominal value. The main purpose of the work is to preserve the operation of the predictive controller as much as possible, in accordance with its operational objectives, when there may be anomalies affecting the elements of the control system, mainly sensors and actuators. Comparing the results obtained considering various types of faults, with situations of normal controlled operation and with the behavior of the sewer network when no control is applied, will allow some conclusions to be drawn at the end.

Chronic Chagas Cardiomyopathy (CCC) results from infection with the protozoan parasite Trypanosoma cruzi and is a prevalent cause of heart disease in endemic countries. We previously found that cardiac fibrosis can vary widely in C3H/HeN mice chronically infected with T. cruzi JR strain, mirroring the spectrum of heart disease in humans. In this study, we examined functional cardiac abnormalities in this host:parasite combination to determine its potential as an experimental model for CCC. We utilized electrocardiography (ECG) to monitor T. cruzi-infected mice and determine whether ECG markers could be correlated with cardiac function abnormalities. We found that the C3H/HeN:JR combination frequently displayed early onset CCC indicators, such as sinus bradycardia and right bundle branch block, as well as prolonged PQ, PR, RR, ST and QT intervals in the acute stage. Our model exhibited high levels of cardiac inflammation and enhanced iNOS expression in the acute stage, but denervation did not appear to have a role in pathology. These results demonstrate the potential of the C3H/HeN:JR host:parasite combination as a model for CCC that could be used for screening new compounds targeted at cardiac remodeling and for examining the potential of anti-parasitic drugs to prevent or alleviate CCC development and progression.

The ACC feature when activated augments the engine performance in real-time. This article presents a novel methodology to predict the optimal adaptive cruise control set speed profile (ACCSSP) by considering all the effecting parameters. This paper investigates engine operating conditions (EOC) criteria to develop a predictive model of ACCSSP in real-time. We developed a deep learning (DL) model using the NARX method to predict engine operating point (EOP) mapping the vehicle-level vectors (VLV). We used real-world field data obtained from Cadillac test vehicles driven by activating the ACC feature for developing the DL model. We used a realistic set of assumptions to estimate the VLV for the future time steps for the range of allowable speed values and applied them at the input of the developed DL model to generate multiple sets of EOP’s. We imposed the defined EOC criteria on these EOPs, and the top three modes of speeds satisfying all the requirements are derived for each second. Thus three eligible speed values are estimated for each second, and an additional criterion is defined to generate a unique ACCSSP for future time steps. Performance comparison between predicted and constant ACCSSPs indicates that the predictive model outperforms constant ACCSSP.

This work is located in a growing sector within the field of renewable energies, wave energy converters (WECs). Specifically, it focuses on one of the point absorbers wave (PAWs) of the hybrid platform W2POWER. With the aim of maximising the mechanical power extracted from the waves by these WECs and reduce their mechanical fatigue, the design of five different model predictive controllers (MPCs) with hard and soft constraints has been carried out. As contribution of this paper, two of the MPCs have been designed with the addition of an embedded integrator. In order to validate the MPCs, an exhaustive study on performance and robustness is realized through simulations carried out in which uncertainties in the WEC dynamics are considered. Furthermore, looking for realistic in these simulations, an identification methodology for PAWs is proposed and validated by means of real time series of a scale prototype.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

The paper deals with the Model Predictive Control (MPC) algorithm as applied to the sensorless control of a Permanent Magnet Synchronous Motor (PMSM). The proposed estimation strategy, based on the unscented Kalman filter (UKF), uses only the measurement of the motor current for the online estimation of speed, rotor position and load torque. Information about the system state feeds the MPC. Results verify the effectiveness and applicability of the proposed sensorless control technique. An implementation in low speed direct drive astronomy telescope mount systems is investigated.

For years, effort has been devoted to establishing an effective bull breeding soundness evaluation procedure; usual research on the subject is based on BBSE (Bull Breeding Soundness Examination) methodologies, which have significant limitations in terms of their evaluation procedure, such as high cost, time-consuming and administratively difficult. This research focuses on the creation of a prediction model to supplement and/or improve the BBSE approach, through the study of two algorithms, Clustering and Artificial Neural Network (ANN), to find the optimum Machine Learning (ML) approach for our application, with an emphasis on data categorization accuracy. The tool is designed to assist veterinary medicine and farmers in identifying key factors and increasing certainty in their decision-making during the selection of bulls for breeding purposes, providing data from a limited number of factors generated from a deep pairing study of bulls. Zebu Bulls, European Bulls, and Crossbred Bulls were the general groupings. The data utilized in the model's creation (N =359) considers five variables that influence improvement decisions. This approach enhances decision-making by 12%. ANN obtained an accuracy of 90%; Precision was 97% for satisfying, 92% for unsatisfying, and 85% for Bad.

In order to reduce the influence of ground vibration generated by tractor during driving and operation on driving stability and driver ride comfort, this paper proposes a control method of tractor active seat suspension based on model predictive control. By establishing a 3-degree of freedom tractor active seat suspension model and a ground excitation input model, a new model predictive controller for the active seat suspension system is designed. The vertical acceleration of the seat center of mass, the seat suspension stroke and the tire dynamic displacement are optimized by limiting the dynamic deflection of the seat suspension and the active force output of the actuator. The control model of MPC tractor active seat suspension system is built and its performance is simulated and verified. The results show that compared with the passive seat suspension and the PID seat suspension, the tractor active seat suspension based on model predictive control (MPC) has better damping characteristics and improves ride comfort.

CAMx-LPiG (Comprehensive Air Quality Model with Extensions – Linear Plume in Grid) is an online hybrid model, based on the Chemistry and Transport Model (CTM) CAMx, that includes a sub-grid scale module to simulate the dispersion of linear road traffic emissions, called LPiG. LPiG is a plume in grid module specifically developed by extending the capabilities of the Lagrangian puff sub-grid model available in CAMx. The online integration of the local scale model within the Eulerian CTM allows for a multiscale simulation of air quality from the regional scale to the urban scale, preserving a coherent description of the chemical state of the atmosphere at all spatial scales and avoiding any double counting of the emissions simulated by the sub-grid module. In this work the model is presented and evaluated against measured NO2 concentrations for the city of Milan for the month of January 2017. The model is able to introduce road traffic induced gradient in NO2 concentration at sub-grid resolution. Moreover, CAMx-LPiG is shown to reduce the bias compared to CAMx stand-alone simulations.

We investigate the power of time series analysis based on a variety of information-theoretic approaches from statistics (AIC, BIC) and machine learning (Minimum Message Length) - and we then compare their efficacy with traditional time series model and with hybrids involving deep learning. More specifically, we develop AIC, BIC and Minimum Message Length (MML) ARMA (autoregressive moving average) time series models - with this Bayesian information-theoretic MML ARMA modelling already being new work. We then study deep learning based algorithms in time series forecasting, using Long Short Term Memory (LSTM), and we then combine this with the ARMA modelling to produce a hybrid ARMA-LSTM prediction. Part of the purpose of the use of LSTM is to seek capture any hidden information in the residuals left from the traditional ARMA model. We show that MML not only outperforms earlier statistical approaches to ARMA modelling, but we further show that the hybrid MML ARMA-LSTM models outperform both ARMA models and LSTM models.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

This work focuses on addressing the dynamic positioning and trajectory tracking problem for a 4 degree-of-freedom (DOF) unmanned underwater vehicle (UUV) in the presence of nonlinear dynamics, parametric uncertainties, system constraints, and time-varying external disturbances. To tackle this problem, a disturbance observer-based control (DOBC) scheme is proposed. The scheme is structured around the model predictive control (MPC) method integrated with an extended active observer (EAOB). Compared to the conventional disturbance observer, the EAOB has the unique ability to handle both external disturbances and system/measurement noises simultaneously. The EAOB leverages a combination of sensor measurements and a system dynamic model to estimate disturbances in real-time, which allows continuous estimation and compensation of time-varying disturbances back to the controller. The proposed disturbance observer-based MPC (DOBMPC) is implemented by feeding the estimated disturbances back into the MPC’s prediction model, which forms a robust adaptive controller with a parameter-varying model. The proposed control strategy is validated through simulations in a Gazebo and Robot Operating System (ROS) environment. The results show that it can effectively reject unpredictable disturbances and improve the UUV’s control performance.

The territory of Serbia is vulnerable to various types of natural and man-made disasters. The risk is not equal across the entire territory, depending on the type of hazard and the expected potential for damage. So far, the level of community disaster resilience has not been determined in Serbia. There are no scientific preconditions for its improvement to reduce the future material and intangible consequences of disasters. Regarding that, the project’s main objective is to develop and validate a predictive model of community disaster resilience based on social identity influences through an investigation impact of social identity indicators on the level of community disaster resilience in Serbia. The project is based on the upcoming research on whether the level of community disaster resilience can be predicted based on social identity indicators, how social identity indicators affect different dimensions of community disaster resilience, and how disasters shape social identity. The project is based on multimethod research in which quantitative (face-to-face interviews in 40 of the 191 municipalities), and qualitative (semi-structured interviews) research methodology will be applied. A developed predictive model with an index of community disaster resilience in Serbia will empower the creation of preconditions for designing public policies, strategies and procedures for improving resilience and reducing the consequences of disasters on people and their property and enhancing citizens’ security. The project will encourage the prediction of community disaster resilience based on social identity indicators, improving disaster foresight and preparing to limit disaster losses. Based on the development of analytical frameworks for understanding community disaster resilience and social identity in disasters, essential preconditions for designing innovative information systems will be created to enable local communities to increase their level of resilience.

Learning models of the cerebellum propose that the cerebellum implements an algorithm which makes iterative adjustments to synaptic transmission strength that collectively determine the response to input in learned patterns following training. We propose instead that pattern recognition and control of firing by output cells are separately handled functions which process independently variable data. This can account for the evidence without a machine learning algorithm. The model is a hybrid of physiological arguments and computational methods used to test and quantify the ideas. We argue inter alia that learning operates at the level of functional groups of Purkinje cells defined by their shared climbing fibre input; Golgi cells have several functions and regulation of parallel fibre activity by Golgi cells is not in the expected way; recoding of input to the cerebellum received in the granular layer converts the number of input variables (variables expressed in mossy fibre input to the system) into a much reduced number of functional variables expressed by internal signals traffic; circuits simultaneously execute separate but integrated functions of pattern memory and output coding; they are able to operate separately because the expression of data used in each varies independently of the other; output rates are not learned but controlled by recent relevant input signals in a window opened by pattern memory; the moment-to-moment probability that a Purkinje cell spikes is synchronised across a microzone; a principal function of functional organisation of Purkinje cells into microzones is to increase resolution of rate coded information received by the output cells of the circuit, and to do so in a very short integration window, so that circuit architecture can be explained partly as a device with this function.

Waste management is an unavoidable technological operation in the process of raw material extraction. The main characteristic of this technological operation is the handling of large quantities of waste material, which can amount to several hundred million cubic metres. Working with this amount of material usually requires high-capacity systems for excavation and loading, a large fleet of trucks for haulage, construction, and maintenance of a complex roads network, use of a significant area of land in order to achieve the required capacities, etc. At the same time, this operation must comply with all administrative and environmental standards. Therefore, optimising waste rock management (particularly haulage and dumping) has the potential to significantly improve the overall value of the project. This paper presents a hybrid model for the optimisation of waste dump design and site selection. The model is based on different mathematical methods (genetic algorithm, analytic hierarchy process and heuristic methods) adapted to different aspects of the problem. The main objective of the model is to provide a solution (in analytical and graphical form) for the draft waste dump design, on the basis of which the final waste dump design can be defined.

In this study, we construct a new Atangana-Baleanu fractional model for whooping cough disease to predict future dynamics of the disease, as well as to suggest strategies to eliminate the disease in an optimal way. We prove that the proposed model has a unique solution which is positive and bounded. To measure contagiousness of the disease, we determine the reproduction number R0 and use it to examine the local and global stability at equilibrium points that have symmetry. Through sensitivity analysis, we determine parameters of the model that are most sensitive to R0. The ultimate aim of this research is to analyze different disease prevention approaches in order to find the most suitable one. For this, we include the vaccination and quarantine compartments in the proposed model and formulate an optimal control problem to assess the effect of vaccination and quarantine rates on disease control in three distinct scenarios. Firstly, we study the impact of vaccination strategy and conclude findings with presentation of graphical results. Secondly, we examine the impact of quarantine strategy on whooping cough infection with possible elimination from the society. Lastly, we implement vaccination and quarantine strategies together to visualize their combine effect on infection control. In addition to the study of an optimal control problem, we examine the effect of fractional order on disease dynamics as well as the impact of constant vaccination and quarantine rates on disease transmission and control. We determine that the optimal control strategy with the three controls is more effective in reducing the spread of whooping cough infection. Implementation of Toufik-Atangana type numercial scheme both for the state and adjoint equations is another contribution of this article.

In this study, we demonstrate how the incorporation of appropriate feature engineering together with the selection of a Machine Learning (ML) algorithm that best suits the available dataset, leads to the development of a predictive model for transformation temperatures that can be applied to a wide range of shape memory alloys. We develop a gradient boosting ML surrogate model capable of predicting Martensite Start, Martensite Finish, Austenite Start, and Austenite Finish transformation temperatures with an average accuracy of more than 95% by explicitly taking care of potential distribution changes when modeling different alloy systems. We included heat treatment, rolling, extrusion processing parameters, and alloy system categorical features in the model input features to achieve more accurate and realistic results. In addition, using Shapley values, which are calculated based on the average marginal contribution of features to all possible coalitions, this study was able to gain insights into the governing features and their effect on predicted transformation temperatures, providing a unique opportunity to examine the critical parameters and features in martensite transformation temperatures.

The objective of this study is to design an optimal model predictive control (MPC) strategy using manipulated variables to control the production of a sufficient amount of hydrogen through low temperature autothermal reforming of dimethyl ether (DME), a reforming reaction performed using PdO/ZnO/γ-Al2O3 catalysts coated on honeycomb cordierite ceramics. Experiments and simulation have verified that the optimal activity temperature of the catalyst is 400 °C, and the hydrogen volume fraction in syngas is over 43%. In the implementation of the hydrogen production system, the MPC controller can precisely determine the feed rates of DME, high-purity air, and water based on the space state equation of the reformer, to achieve the anti-disturbance of the reformer temperature. Thus, the reduction of hydrogen yield and sintering of the catalyst as a result of overheating are prevented. As the static and dynamic performance of hydrogen production exhibits excellent tracking of the setpoints, an autonomous, automated, and reliable continuous system was designed to meet the desired hydrogen demand situation. This study shows that an autonomous, automated, and reliable continuous hydrogen production reforming system can be designed to actively respond to the on-board hydrogen usage situation.

PURPOSE: Breast cancer tumors frequently have intratumor heterogeneity. Tumors with high intratumor heterogeneity have caused therapeutic resistance and have human epidermal growth factor receptor 2 (HER2) heterogeneity in response to HER2-targeted therapies. This study aimed to investigate whether high HER2 heterogeneity levels were clinically related to poor prognosis for HER2-targeted adjuvant therapies resistance in primary breast cancers. METHODS: This study included patients with primary breast cancer (n = 251) treated with adjuvant HER2-targeted therapies. HER2 heterogeneity was manifested by the shape of HER2 fluorescence in situ hybridization amplification (FISH) distributed histograms with HER2 gene copy number within a tumor sample. Those heterogeneity classified each tumor into the biphasic grade graph (high heterogeneity [HH]) group and the monophasic grade graph (low heterogeneity [LH]) group. Both groups were evaluated for disease-free survival (DFS) and overall survival (OS) for a median of ten years of annual follow-up. RESULTS: Of 251 patients with HER2-positive breast cancer, 46 (18.3%) and 205 (81.7%) were classified into the HH and LH groups, respectively. The HH group had more distant metastases and a poorer prognosis than the LH group (DFS: P < 0.001 (HH:63% vs LH:91% at 10 years), and OS: P = 0.012 (HH:78% vs LH:95% at 10 years). CONCLUSION: High HER2 heterogeneity is a poor prognostic factor in patients with HER2-positive breast cancer. A novel approach of heterogeneity, which is manifested by the shape of HER2 FISH distributions, might be clinically useful in the prognosis prediction of patients after HER2 adjuvant therapy.

Agriculture is the main driver of depletion resources worldwide, and its duty is to ensure food security within a rapidly increasing demographic and urbanization, so it is important to transition to sustainable production systems. Vertical crops (VCs) can reduce the pressure on conventional agriculture because they save water and nutrients and increase crop yield. Therefore, this study aimed to validate a proposed predictive model (PM) to simulate water and nutrient uptake in vertical crops under greenhouse conditions. Based on the Penman-Monteith equation, PM estimates transpiration, while nutrient uptake was estimated using the Carmassi-Sonneveld submodel. PM was experimentally evaluated for vertically grown lettuce under Mediterranean greenhouse conditions, during spring 2023. The irrigation technique was a closed-loop fertigation circuit. The experimental consisted of testing two densities (50 and 80 plants·m-2), where each unit of the experiment unit was divided into three heights (low, medium, and upper). It performed ANOVA with a value of p &lt; 0.05 and R2 to assess PM performance. The results suggest a high degree of PM, since R2 ranged from 0.7 to 0.9 for the uptake of water and nutrients. Both densities had a yield between 17-20 times higher than conventional lettuce production and significant savings in water, between 85-88%. In this sense, PM has great potential to intelligently manage VC fertigation, saving water and nutrients, which represents an advance towards reaching SDG 6 and SDG 12, within the 2030 Agenda.

Social and academic integration variables have shown to be relevant for the understanding of university dropout. However, there is less evidence regarding the influence of these variables on dropout intention, as well as predictive models that explain their relationships. Improvements in this topic become relevant considering that dropout intention stands as a useful measure to anticipate and intervene on this phenomenon. The objective of the present study was to evaluate a predictive model for the university dropout intention that considers the relationships between social and academic variables, during the first university semester of 2020. The research was carried out using a cross-sectional associative-predictive design, with a convenience sampling (n=711) due the restrictions of pandemic period. The results showed a good fit of the proposed hypothetical model that explains 38.7% of dropout intention. Both social support and perceived social isolation predicted the sense of belonging, and through it, engagement. Previous academic performance predicted early academic performance, and through it, engagement. The set of variables predicted the intention to quit, through engagement. These results are a contribution both to the understanding of the phenomenon and to guide potential interventions in the early stages of the university experience.

Malicious apps specifically aimed at the Android platform have increased in tandem with the proliferation of mobile devices. Malware is now so carefully written that it is difficult to detect. Due to the exponential growth in malware, manual methods of malware are increasingly ineffec-tive. Although prior writers have proposed numerous high-quality approaches, static and dy-namic assessments inherently necessitate intricate procedures. The obfuscation methods used by modern malware are incredibly complex and clever. As a result, it cannot be detected using only static malware analysis. As a result, this work presents a hybrid analysis approach, partially tai-lored for multiple-feature data, for identifying Android malware and classifying malware families to improve Android malware detection and classification. This paper offers a hybrid method that combines static and dynamic malware analysis to give a full view of the threat. Three distinct phases make up the framework proposed in this research. Normalization and feature extraction procedures are used in the first phase of pre-processing. Both static and dynamic features undergo feature selection in the second phase. Two feature selection strategies are proposed to choose the best subset of features to use for both static and dynamic features. The third phase involves ap-plying a newly proposed detection model to classify android apps; this model uses a neural net-work optimized with an improved version of HHO. Application of binary and multi-class classi-fication is used, with binary classification for benign and malware apps and multi-class classifica-tion for detecting malware categories and families. By utilizing the features gleaned from static and dynamic malware analysis, several machine-learning methods are used for malware classifi-cation. According to the results of the experiments, the hybrid approach improves the accuracy of detection and classification of Android malware compared to the scenario when considering static and dynamic information separately.

Social media platforms have been entirely an undeniable part of the lifestyle for the past decade. Analyzing the information being shared is a crucial step to understanding human behavior. Social media analysis aims to guarantee a better experience for the user and risen user satisfaction. For deriving any further conclusion, first, it is necessary to know how to compare users. In this paper, a hybrid model has been proposed to measure Twitter profiles’ similarity and quantifies the likeness degree of profiles by calculating features considering users’ behavioral habits. For this, first, the timeline of each profile has been extracted using the official TwitterAPI. Then, in parallel, three aspects of a profile are deliberated. Behavioral ratios are time-series-related information showing the consistency and habits of the user. Dynamic time warping has been utilized to compare the behavioral ratios of two profiles. Next, the audience network is extracted for each user, and for estimating the similarity of two sets, Jaccard similarity is used. Finally, for the Content similarity measurement, the tweets are preprocessed respecting the feature extraction method; TF-IDF and DistilBERT for feature extraction are employed and then compared using the cosine similarity method. Results have shown that TF-IDF has slightly better performance; therefore, the more straightforward solution is selected for the model. Similarity level of different profiles. As in the case study, a Random Forest classification model was trained on almost 20000 users revealed a 97.24% accuracy. This comparison enables us to find duplicate profiles with nearly the same behavior and content.

Dissolved Oxygen (DO) concentration is a vital parameter that indicates water quality. DO short term forecasting using time series analysis on data collected from an aquaculture pond is presented here. This can provide data support for an early warning system for an improved management of the aquaculture farm. The conventional forecasting approaches are commonly characterized by low accuracy and poor generalization problems. In this article, we present a novel hybrid DO concentration forecasting method with ensemble empirical mode decomposition (EEMD) based LSTM (Long short-term memory) neural network (NN). With this method, first, the sensor data integrity is improved through linear interpolation and moving average filtering methods of data preprocessing. Next, the EEMD algorithm is applied to decompose the original sensor data into multiple intrinsic mode functions (IMFs). Finally, the feature selection is used to carefully select IMFs that are strongly correlated with the original sensor data and integrate both into inputs for the NN. The hybrid EEMD-based LSTM forecasting model is then constructed. Performance of this proposed model in training and validation sets was compared with the observed real sensor data. To obtain the exact evaluation accuracy of the forecasted results of the hybrid EEMD-based LSTM forecasting model, three statistical performance indices were adopted: MAE, MSE, and RMSE. Results presented for short term (12-hour period) and long term (1-month period) give a strong indication of suitability of this method for forecasting DO values.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

Background: Neonatal transportation of sick newborns is a major predictor of outcome. Prompt identification of the sickest newborns allows immediate corrective intervention and outcome optimization. Multiple severity scores were developed, however an optimal score has not yet been identified. Aim: To identify a rapid, accurate, and easy to perform score predictive for neonatal mortality in outborn neonates. Material and methods: All neonates, irrespective of gestational age, admitted by transfer in our level III regional neonatal unit between 01.01.2015 and 31.12.2021 were included. Infants with congenital critical abnormalities were excluded. Sick neonatal score (SNS) was calculated and compared between survivors and non-survivors. Gestational age (GA), birth weight (BW), gender, Apgar score, place of birth, time between delivery and admission (AT), early onset sepsis were collected from medical records and compared between study groups. Subgroup analysis was performed based on gestational age (preterm versus term infants). A new score was elaborated, including GA, BW, and AT, namely MSNS-AT score, to further improve mortality prediction. The main outcomes were mortality prediction using SNS and MSNS-AT score. Univariable and multivariable analysis, including Cox regression, were performed using SPSS Statistic 22.0. P-value was considered statistically significant if <0.05, 95% confidence intervals, odds ratio and hazard ratios were calculated were appropriate. Results: A total of 418 outborn infants were admitted during study period; 15 infants were excluded due to critical congenital defects. Out of 403 outborn infants, 217 born prematurely (53.8%), 224 males (55.6%), 20 died (4.96%). Compared to the survivors, the non-survivor neonates had significantly lower GA, BW, and SNS score (p<0.05), although only SNS score remained significantly lower in all subgroups (preterm vs term infants). A SNS score ≤8 was associated with mortality both in the whole study group and in subgroups (p<0.001). Time to admission was significantly associated with increased mortality rate in the whole group (p<0.05) and in preterm infants but not in term ones (p>0.05). In univariable and multivariable Cox regression models, MSNS-AT score, with a cut-off optimal value of ≤10 was more precise in predicting mortality compared to SNS (AUC 0.735 vs. 0.775) when applied to the entire group, had a lower accuracy in the term infants (AUC 0.765 vs 0.809) and a better accuracy the preterm infants group (AUC 0.885 vs. 0.810). Conclusions: The MSNS-AT score – calculated by adding GA, BW, and AT to the SNS score - significantly improved mortality prediction at admission in the whole study group as compared to SNS score. The best accuracy prediction of MSNS-AT score was observed in preterm infants suggesting that, besides GA and BW, TA may be decisive for the outcome of outborn preterm infants. Further studies are necessary to confirm the predictive value of MSNS-AT score and to identify variables that can improve its value in term infants without affecting the simplicity, ease, and rapidity of the scoring system.

This work presents a nonlinear model predictive control scheme that challenges overcoming the obstacles holding back over decades to develop affordable autonomous control and monitoring systems applied in the large-scale industry. Among the numerous proposals in the literature, most do not consider the significant fluctuation of kinetic parameters in the reduced mathematical model ADM2, widely used for control and monitoring purposes. The prevalent cause, on a basis, is the lack of information caused by some dynamics and parameters that cannot be measured in real-time by reliable sensors. In addition, to make matters worse, those systems inherently act with nonlinear nature and have a high sensitiveness to uncontrollable inputs and perturbations. Therefore, to prevent these drawbacks, this work proposes a new methodology that reconstructs the lack of information from the non-measurable dynamics, concentration of bacterias, and the kinetic parameters related to reaction rates. Simulations results demonstrate the effectiveness of the methodology compared with traditional industrial control schemes.

As the natural resources are getting exhausted, the concept of sustainable development of region has received increasing attentions, especially for resource-dependent cities. In this paper an innovative method that emergy analysis and IPAT (Human Impact Population Affluence Technology) model were combined in order to analyze the quantitative relationship of economic growth and energy consumption and further to evaluate its overall sustainability level. Taiyuan, a traditional, resource-dependent city in China, is selected as the case study region. The main results show that total emergy of Taiyuan increased from 9.023× 1023 sej in 2007 to 9.116× 1023sej in 2014, with 38% reduction on non-renewable emergy and 125% growth on imported emergy. Regional emergy money ratio (RMB) was reduced by 48% from 5.31× 1013sej/$ in 2007 to 2.74× 1013sej/$ in 2014, indicating that the increasing speed of consuming resources and energy was faster than the increase of GDP, and that Taiyuan’s money purchasing power declined. The lower emergy sustainability index (ESI) indicates that Taiyuan was explored and produced large quantities of mineral resources, which puts more stress on the environment as a consequence, and that this is not sustainable in the long run. The IPAT analysis demonstrates that Taiyuan sticks to the efforts of energy conservation and environmental protection, in order to promote regional sustainable development, it is necessary to take an integrated effort. Policy insights suggest that resourceful regions should improve include energy and resource efficiency, optimizing energy and resourceful structure.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Usually, the vector control of the induction machine (IM) is done by using cascade control structures with conventional linear PI controllers, the inner loop being designed for current control, and the outer loop for rotor flux and speed control. In this paper, starting from the dq model of the IM with the rotor magnetic flux space vector aligned along the d axis, advanced control algorithms are proposed for the two control loops of the cascade structure. For the current inner loop, after the decoupling control of the two dq currents, predictive algorithms with constraints are used to control and limit the currents. Since the outer loop has a nonlinear affine multivariable plant model, a homotopy-based variant of feedback linearization is used to obtain a non-singular decoupling matrix of the feedback transformation even when the rotor flux is zero at the start-up of the motor. During the continuous variation of the homotopy parameter, the model of the plant is variable, in which case the model free algorithms are properly used to control the flux and speed of the IM. The comparative analysis obtained for the cascade structure with conventional PI controllers and advanced algorithms, respectively, shows that the last lead to improve the dynamical performance of the IM.

The pharmaceutical industry is making significant strides in enhancing process comprehension through the development of concepts like Quality by Design (QbD) and Process Analytical Technology (PAT). This shift has moved from traditional offline testing methods to real-time estimation of product quality. The dissolution characteristics of pharmaceutical tablets play a crucial role in maximizing the release of medications and their bioavailability. One factor that can affect dissolution is the blending procedure. Inadequate mixing can lead to patches of concentrated active components or excipients within the tablet, resulting in inconsistent dissolution behavior. A study investigated the impact of blending time and speed on the dissolution behavior of Amlodipine tablets using near-infrared (NIR) spectroscopy and multivariate modeling. NIR spectra were collected for Amlodipine tablets produced under various blending conditions using a 2-level central composite design. Dissolving profiles were analyzed using a USP dissolution device. Multivariate analysis techniques, including principal component analysis (PCA), partial least squares (PLS), Support Vector Machine (SVM), and Artificial Neural Networks (ANN), were applied to the collected NIR spectra. The findings demonstrated that blending speed and time had a significant influence on the dissolving properties of Amlodipine tablets. Blending at faster speeds and for shorter durations resulted in excessive shear and insufficient mixing, ultimately reduced drug release. The multivariate models constructed using ANN outperformed SVM and PLS in predicting dissolution profiles based on NIR spectra. This research highlights the effectiveness of NIR spectroscopy and multivariate modeling in optimizing tablet dissolution. These advancements enable continuous manufacturing of high-quality pharmaceutical products.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Age estimation in dental radiographs Orthopantomography (OPG) is a medical imaging technique that physicians and pathologists utilise for disease identification and legal matters. For example, for estimating post-mortem interval, detecting child abuse, drug trafficking, and identifying an unknown body. Recent development in automated image processing models improved the age estimation's limited precision to an approximate range of +/- one year. While this estimation is often accepted as accurate measurement, age estimation should be as precise as possible in most serious matters, such as homicide. Current age estimation techniques are highly dependent on manual and time-consuming image processing. Age estimation is often a time-sensitive matter in which the image processing time is vital. Recent development in Machine learning-based data processing methods has decreased the imaging time processing; however, the accuracy of these techniques remains to be further improved. We proposed an ensemble method of image classifiers and transfer learning techniques to enhance the accuracy of age estimation using OPGs from one year to a couple of months (1-3-6). This hybrid model is based on convolutional neural networks (CNN) and K nearest neighbours (KNN). The hybrid (HCNN-KNN) model was used to investigate 1,922 panoramic dental radiographs of patients aged 15 to 23. These OPGs were obtained from the various teaching institutes and private dental clinics in Malaysia. To minimise the chance of overfitting in our model, we used the principal component analysis (PCA) algorithm and eliminated the features with high correlation. To further enhance the performance of our hybrid model, we performed systematic image pre-processing. We applied a series of classifications to train our model. We have successfully demonstrated that combining these innovative approaches has improved the classification and segmentation and thus the age-estimation outcome of the model. Our findings suggest that our innovative model, for the first time, to the best of our knowledge, successfully estimated the age in classified studies of one year old, six months, three months and one-month-old cases with accuracies of 99.98, 99.96, 99.87, and 98.78 respectively.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

As most of the videos are destined for human perception, many techniques have been designed to improve video coding based on how the human visual system perceives video quality. In this paper, we propose the use of two perceptual coding techniques, namely contrast masking and texture masking, jointly operating under the High Efficiency Video Coding (HEVC) standard. These techniques aim to improve the subjective quality of the reconstructed video at the same bit rate. For contrast masking, we propose the use of a specific weighting matrix for each block size (from 4×4 up to 32×32). We achieve average Bjøntegaard Delta-Rate (BD-rate) gains of between 2.5% and 4.48%, depending on the perceptual metric and coding mode used. The texture masking scheme is based on the classification of each coding unit, using its mean directional variance features as input to a support vector machine model. According to this classification, the block’s energy, the type of coding unit, and its size, an over-quantization is computed to provide a QP offset (DQP) for this coding unit. By applying both techniques in the HEVC Reference Software, an overall average of 5.79% BD-rate gain is achieved.

Hospital readmission and length of stay prediction provide info to manage hospitals’ bed capacity and the number of required staff, especially during pandemics. We present a hybrid deep model called Genetic Algorithm-Optimized Convolutional Neural Network (GAOCNN) with a unique preprocessing method to predict hospital readmission and the length of stay in patients having various conditions. GAOCNN uses one-dimensional convolutional layers to predict hospital readmission and length of stay. The parameters of the layers are optimized using a genetic algorithm. To show the performance of the proposed model in patients with various conditions, we evaluate the model under three healthcare datasets; the Diabetes 130-US hospitals dataset, the COVID-19 dataset, and the MIMIC-III dataset. The diabetes 130-US hospitals dataset has information on both readmission and the length of stay, while COVID-19 and MIMIC-III datasets just include information on the length of stay. Experimental results show that the proposed model’s accuracy for hospital readmission is 97.2% for diabetic patients. Also, the accuracy of the length of stay prediction is 89%, 99.4%, and 94.1% for diabetic, COVID-19, and ICU patients, respectively. These results confirm the superiority of the proposed model compared to existing methods. Our findings offer a platform for managing healthcare funds and resources for patients with various diseases.

In order to support a massive number of resource-constrained Internet-of-Things (IoT) devices and machine-type devices, it is crucial to design future beyond 5G/6G wireless networks in an energy-efficient manner while incorporating suitable network coverage expansion methodologies. To this end, this invited paper proposes a novel two-hop hybrid active-and-passive relaying scheme to facilitate simultaneous wireless information and power transfer (SWIPT) considering both the time-switching (TS) and power-splitting (PS) receiver architectures, while dynamically modelling the involved dual-hop time-period (TP) metric. An optimization problem is formulated to jointly optimize the throughput, harvested energy, and transmit power of a SWIPT-enabled system with the proposed hybrid scheme. In this regard, we provide two distinct ways to obtain suitable solutions based on the Lagrange dual technique and Dinkelbach method assisted convex programming, respectively, where both the approaches yield an appreciable solution within polynomial computational-time. The experimental results are obtained by directly solving the primal problem using a non-linear optimizer. Our numerical results in terms of weighted utility function show the superior performance of proposed hybrid scheme over passive repeater-only and active relay-only schemes, while also depicting their individual performance benefits over the corresponding benchmark SWIPT systems with the fixed-TP.

The future of intelligent manufacturing machines involves autonomous selection of process parameters to maximize productivity while maintaining quality within specified constraints. To effectively optimize process parameters, these machines need to adapt to existing uncertainties in the physical system. This paper proposes a novel framework and methodology for feedrate optimization that is based on a physics-informed data-driven digital twin with quantified uncertainty. The servo dynamics are modeled using a digital twin, which incorporates the known uncertainty in the physics-based models and predicts the distribution of contour error using a data-driven model that learns the unknown uncertainty on-the-fly by sensor measurements. Using the quantified uncertainty, the proposed feedrate optimization maximizes productivity while maintaining quality under desired servo error constraints and stringency (i.e., the tolerance for constraint violation under uncertainty) using a model predictive control framework. Experimental results obtained using a 3-axis desktop CNC machine tool and a desktop 3D printer demonstrate significant cycle time reductions of up to 38% and 17% respectively, while staying close to the error tolerances compared to the existing methods.

The paper portrays predictive models for dissolved oxygen (DO) levels in an urban lake using common water quality parameters like Temperature, pH, Conductivity and ORP at a time. Data were sampled using three real-time, industry-standard sensors, OPTOD, CTZN, and PHEHT, and then interpolated using the ArcGIS kriging technique. Correlation studies were analyzed through the ML algorithm, the correlation study signified a highly positive correlation between DO and other water parameters and the model was corroborated by R-score in order to create the linear regression model. In addition, an artificial neural network- a machine learning method using the Levenberg-Marquardt algorithm was developed to build a model to predict the do as well. Then, the performance of the models was validated and also the R² accuracy was checked of the predicted data against the actual data. Thus, the appropriateness of the ANN model for the forecasting of investigated attributes is indicated by the fact that the discrepancy between the forecasted and real ANN model is significantly lesser than that of the regression model. However, the model can be used to reveal DO data from unknown urban lake water.

Over the years, various models have been developed in the stages of the mining process that have allowed predicting and enhancing results, but it is the breakage the variable that connects all the activities of the mining process from the point of view of costs (drilling, blasting, loading, hauling, crushing and grinding). To improve this process, we come up with an idea to develop a breakage prediction model; on the basis of the main variables involved in the drilling and blasting process. For this purpose, we design a computer model based on an Artificial Neuronal Networks (ANN), built by using the most representative variables that come into play with drilling and blasting, such as: the properties of the explosives, the geomechanical parameters of the rock mass, and the design parameters of drilling-blasting. For its experimentation and validation, we have taken the data from a copper mine as reference located in the north of Chile, because of we have the dataset of that ore deposit, which is valid and reliable to evaluate prediction problems based on ANN applied to copper mines. The ANN architecture was of the supervised type, feedforward, with 3 layers and 13 neurons in the only hidden layer, trained with the input data using a dataset with the previously mentioned variables, which then were compared with the breakage results. The model was feed backed in its learning process until it becomes perfected, and is a prediction option that can be used in future blasting of ore deposits with similar characteristics using the same representative variables. Therefore, this is a valid alternative for predicting rock breakage, given that it has been experimentally validated, and has achieved moderately reliable results, providing higher correlation coefficients than traditional models, and with the additional advantage that an ANN model provides, due to its ability to learn and recognize compiled dataset patterns. In this way, using this computer model we can obtain satisfactory results that allow us to predict breakage, providing an alternative for evaluating the costs that this entails.

Hybrid materials are a recent addition in the field of Restorative Dentistry for computer-assisted design/ computer-assisted manufacturing (CAD/CAM) indirect restorations. The long–term clinical success of modern dental restorative materials follows a multifactorial pattern. Among the characteristics, affecting the longevity of a restoration, mechanical properties and physicο – chemical interactions are of utmost importance. While numerous researchers constantly evaluate the mechanical properties, the biological background of resin–based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze the biofilm formation on the surfaces of novel hybrid, resin–based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence the initial bacterial adhesion; however most studies focus on in vitro protocols, whereas in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing in that manner the accurate understanding of the bioadhesion phenomenon in the oral cavity.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

To overcome the time-consuming drawbacks of Computational Fluid Dynamics (CFD) numerical simulations, this paper proposes a hybrid model based on a parallel architecture based on the concept of intelligent aerodynamics, named PA-TLA (Parallel Architecture combining TCN, LSTM, and Attention mechanism). This model utilizes CFD data to drive efficient predictions of aircraft wake evolution at different initial altitudes during the approach phase. Initially, CFD simulations of continuous initial altitudes during the approach phase are used to generate aircraft wake evolution data, which are then validated against real-world LIDAR data to verify their reliability. The PA-TLA model is designed based on a parallel architecture, combining Long Short-Term Memory networks (LSTM), Temporal Convolutional Networks (TCN), and a tensor concatenation module based on the attention mechanism, which ensures computational efficiency while fully leveraging the advantages of each component in a parallel processing framework. The study results show that the PA-TLA model outperforms both the LSTM and TCN models in predicting the three characteristic parameters of aircraft wake: vorticity, circulation, and Q-criterion. Compared to the serially structured TCN-LSTM, PA-TLA achieves an average reduction in mean squared error (MSE) by 6.80%, mean absolute error (MAE) by 7.70%, and root mean square error (RMSE) by 4.47%, with an average increase in the coefficient of determination (R²) by 0.36%, and a 35% improvement in prediction efficiency. Lastly, this study combines numerical simulation and the PA-TLA deep learning architecture to analyze the characteristics of wake evolution during the near-ground phase, providing theoretical value for further reducing aircraft wake intervals and enhancing airport operational efficiency.

In era of ever-expanding data and knowledge, we lack a centralized system that maps all the faculties to their research works. This problem has not been addressed in the past and it becomes challenging for students to connect with the right faculty of their domain. Since we have so many colleges and faculties this lies in the category of big data problem. In this paper, we present a model which works on the distributed computing environment to tackle big data. The proposed model uses apache spark as an execution engine and hive as database. The results are visualized with the help of Tableau that is connected to Apache Hive to achieve distributed computing.

Preventive Maintenance (PM) is a periodic maintenance strategy, which has great results for devices in extending their life, increasing productivity, and most importantly, help avoid unexpected breakdowns and their costly consequence. A preventive maintenance scheduling (PMS) is determining the time for carrying out PM, and it represents a sensitive issue in terms of impact on production if the time for the PM process is not optimally distributed. In this study, hybrid heuristic methods were used to solve the PMS problem, as genetic algorithm and Tabu research were adopted. The optimal solution was reached in a short time compared to previous studies in which optimal methods were used, integer programming and nonlinear integer programming. Also, sensitivity analysis was applied to measure the robustness and strength of the method used, where an optimal solution was obtained for all experiments and in record time. This method can be used for power plants in privet or public sectors, to generate an optimal PMS, to save money, and to avoid water or electricity cuts.

In some applications of microgrid and distributed generation, it is required to feed islanded or stand-alone loads with high-quality voltage to provide low total harmonic distortion (THD). To fulfil these demands, an LC filter is connected to the output terminals of power electronics converters. A cascaded voltage and current control loop with pulse-width modulation schemes are used to regulate the voltage and current in these systems. However, these strategies have some drawbacks, particularly when multiple-input multiple-output plants (MIMO) are controlled using single-input single-output (SISO) design methods. This methodology usually produces a sluggish transient response and cross-coupling between different control loops. In this paper, a model predictive control (MPC) strategy based on the concept of optimal switching sequences (OSS) is designed to control voltage and current in an LC filter connected to a three-level neutral-point clamped converter. The strategy solves two well-formulated optimisation problems to achieve control of the LC filter variables and the voltages of the DC-link capacitors. Hardware-in-the-Loop (HIL) results are obtained to validate the feasibility of the proposed strategy, using a PLECS-RT HIL platform and a DSP Microlab Box controller. In addition to the good dynamic performance of the proposed OSS-MPC, it is demonstrated by the HIL results that the control algorithm is capable of obtaining low total harmonic distortion (THD) in the output voltage for different conditions.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

In this paper, the forecast horizon and solar variability influences on MHFM model based on multiscale decomposition, AR and NN models, are studied. This article follows the works published in [1] showing the performance of the MHFM using 3 multiscale decomposition methods and a forecast horizon equal to 1 hour. Several forecast horizon strategies and his influence on the MHFM performances are investigated. We show that the best strategy for a rRMSE variying from $4.43\%$ to $10.24\%$ is obtained for forecast horizons from $5$ minutes to $6$ hours. In a second part, the solar variability influence on the MHFM is studied. A classification based on a shows that the best performance of MHFM is obtained for clear sky days with a rRMSE of $2.91\%$ and worst for cloudy sky days with a rRMSE of $6.73\%$.

Quantitative structure-activity relationship (QSAR) model is adopted to study the relationship between the chemical and physical properties of various substances and the structure. Through QSAR studies, the internal relationship between the invisible structure and the activity can be obtained. In this paper, a novel chaos-enhanced accelerate particle swarm algorithm (CAPSO) is proposed, which is used to molecular descriptors screening and optimization of the weights of back propagation artificial neural network (BP ANN). Then, the QSAR model based on CAPSO and BP ANN is put forward, hereinafter referred to as CAPSO BP ANN model. The prediction experiment showed that the CAPSO algorithm is a reliable method for screening molecular descriptors and the five molecular descriptors obtained by CAPSO algorithm could well characterize the molecular structure of each compound in pKa prediction. The experimental results also showed the CAPSO BP ANN model has a good performance in predicting the pKa values of various compounds, the absolute mean relative error, root mean square error, and square correlation coefficient are respectively 0.5364, 0.0632, and 0.9438, indicating the higher prediction accuracy and correlation. The proposed hybrid intelligent model can be applied in all kinds of engineering design, prediction of physical and chemical properties and intelligent calculation.

The universal Debye – Mayer – Kelly hybrid model was proposed for the description of the heat capacity from 0 K to the melting points of substance within the experimental uncertainty for the first time. To describe the heat capacity, the in-house software on the base of commercial one DELPHI-7 was used with a 95% confidence level. To demonstrate the perfect suitability of this model, a thermodynamic analysis of the heat capacities of the fourth group elements, and some compounds of the A^IIIB^V and A^IIB^VI phases was carried out. It produced good agreement within the experimental uncertainty. There is no a similar model description in literature.The Similarity Method is a convenient and effective tool for critical analysis of the heat capacities of isostructural phases, which was used as an example for diamond-like compounds. Phases with the same sum of the atomic numbers of elements (Z), such as diamond and B_0.5 N_{0.5 (cub)} (Z = 6); pure silicon (Si) and Al_0.5 P_0.5 (Z=14); pure germanium (Ge) and Ga_0.5 As_0.5 (Z = 32)); pure grey tin (alpha-Sn) and In_0.5 Sb_0.5, and Cd_0.5 Te_0.5 (Z = 50) have the same heat capacity experimental values in the solid state. The proposed models can be used to both different binary and multicomponent phases. It helps to standardize the physicochemical constants.

This paper describes a case study for applying of hybrid-electric propulsion system for a general aviation aircraft. The work was performed by a joint team of CIRA and the Department of Industrial Engineering of the University of Naples “Federico II”. Electric and hybrid electric propulsion for aircraft has gained widespread and significant attention over the past decade. The driver for industry interest has principally been the need to reduce emissions of combustion engine exhaust products and noise, but increasingly studies revealed potential for overall improvement in energy efficiency and mission flexibility of new aircraft types. The project goal was to demonstrate feasibility of aeronautic parallel hybrid-electric propulsion for a Light aircraft varying the mission profiles and the electric configuration. Through a creation, and application, of a global model, with software AMESim^®, in which it can be represented everything about the components chosen by the industrial partners, some interesting considerations are carried out. In particular, it was confirmed that with the only integration of state of the art technologies, for some particular missions, the advantages of aircraft hybrid-electric propulsion, for light aircraft, are notable.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

The increasing penetration of renewable energy sources in power grids highlights the role of battery energy stor- age systems (BESSs) in enhancing the stability and reliability of electricity. A key challenge with the renewables’, specially the BESSs, integration into the power system is the lack of proper dynamic model for stability analysis. Moreover, a proper control design for the power system is a complicated issue due to its complexity and inter-connectivity. Thus, the application of decentralized control to improve the stability of a large- scale power system is inevitable, especially in distributed energy sources (DERs). This paper presents an optimal distributed hybrid control design for the interconnected systems to suppress the effects of small disturbances in the power system employing utility-scale batteries based on existing battery models. The results show that i) the smart scheduling of the batteries’ output reduces the inter-area oscillations and improves the stability of the power systems; ii) the hybrid model of the battery is more user-friendly compared to the Western electricity coordinating council (WECC) model in power system analysis.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The following paper describes an economical, multiple model predictive control (EMMPC) for an air conditioning system of a confectionery manufacturer in Germany. The application consists of a packaging hall for chocolate bars, in which a new local conveyor belt air conditioning system is used and thus the temperature and humidity limits in the hall can be significantly extended. The EMMPC calculates the optimum energy or cost humidity and temperature set points in the hall. For this purpose, time-discrete state space models and an economic objective function with which it is possible to react to flexible electricity prices in a cost-optimised manner are created. A possible future electricity price model for Germany with a flexible EEG levy was used as a flexible electricity price. The flexibility potential is determined by variable temperature and humidity limits in the hall, which are oriented towards the comfort field for easily working persons, and the building mass. The building mass of the created room model is used as a thermal energy store. Considering electricity price and weather forecasts as well as internal, production plan-dependent load forecasts, the model predictive controller directly controls the heating and cooling register and the humidifier of the air conditioning system.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Day-ahead forecasting of electricity prices is important in deregulated electricity markets for all the stakeholders: energy wholesalers, traders, retailers, and consumers. Electricity price forecasting is an inherently difficult problem due to its special characteristic of dynamicity and non-stationarity. In this paper, we present a robust price forecasting mechanism that shows resilience towards aggregate demand response effect and provides highly accurate forecasted electricity prices to the stakeholders in a dynamic environment. We employ an ensemble prediction model in which a group of different algorithms participate in predicting the price for each hour of a day. We propose two different strategies, namely, Fixed Weight Method (FWM) and Varying Weight Method (VWM), for selecting each hour's expert algorithm from the set of participating algorithms. In addition, we utilize a carefully engineered set of features selected from a pool of features derived from information such as past electricity price data, weather data, and calendar data. The proposed ensemble model offers better results than both the Pattern Sequence-based Forecasting (PSF) method and our own previous work using Artificial Neural Networks (ANN) alone do on the datasets for New York, Australian, and Spanish electricity markets.

Background: Large-cell neuroendocrine carcinoma presents significant treatment challenges owing to its rarity and limited therapeutic options. The LANCE study was designed to explore the survival benefits of incorporating atezolizumab in chemotherapy for metastatic LCNEC. Methods: In this non-randomized study, patients with metastatic LCNEC were treated with ei-ther standard chemotherapy plus atezolizumab or standard chemotherapy alone. The primary outcomes measured were progression-free survival (PFS) and overall survival (OS), with an ex-ploratory analysis of miR375 in plasma as a potential biomarker. Results: Of the 22 screened patients, 17 met the inclusion criteria and were stratified into the atezolizumab and chemotherapy (n=10) or chemotherapy alone(n=7) groups. After a median follow-up of 23.3 months, the 12-month survival rate for the atezolizumab group was 57.1% (95% CI: 32.6%-100%) and 45.7% at 24 months (95% CI: 22.4%-93.2%). In contrast, the chemotherapy group had a 14.3% survival rate at both 12 and 24 months (95% CI: 2.33%-87.7%). The log-rank test for survival showed a statistically significant difference in the atezolizumab-treated group (chi-squared = 4, df = 1, p = 0.04). A non-significant correlation was found between disease pro-gression and elevated levels of miR375. Conclusions: This pilot study suggests that atezolizumab combined with chemotherapy may be effective in treating metastatic LCNEC. The non-significant correlation between plasma miR375 levels and disease progression suggests its biomarker potential, warranting further validation research.

The present work is focused on functionalizing Montmorillonite (Mt) with poly dimethyl siloxane (PDMS) to develop a hybrid membrane reactor for the removal of Co (II) and Ni (II) ions from model wastewater samples. The specific surface area of the novel material was found to be 444 m2 /g. X-Ray Diffraction (XRD) and Fourier Transform Infra-Red (FTIR) spectra reveal the formation of exfoliated composite material. The efficiency of this membrane material was determined by subjecting it to continuous filtration experiments. It was able to remove 50% of Co (II) and 75% of Ni (II) ions, respectively, in one cycle of filtration in less than three minutes of operation with a permeate flux rate of 675 L/m2/H and 975 L/m2/H respectively, for both the ions.

This article presents a forecast model that uses a hybrid architecture of recurrent neural networks (RNN) with surface neural networks (ANN), based on historical records of exported active energy (EAE) and weather data. Two types of models were developed: the first type includes six models that use EAE records and weather variables as inputs, while the second type includes eight models that use only weather variables. Different metrics were applied to assess the performance of these models, and the best model of each type was selected. Finally, a comparison of the performance between the selected models of both types is presented, and they are validated with real data provided by a solar plant, achieving acceptable levels of accuracy. The selected model of the first type has an RMSE of 0.19, MSE of 0.03, MAE of 0.09, a correlation coefficient of 0.96, and a determination coefficient of 0.93. The other selected model of the second type showed lower precision in the metrics (RMSE = 0.24, MSE = 0.06, MAE = 0.10, Corr. Coef. = 0.95, and Det. Coef. = 0.90). Both models demonstrated good performance and acceptable accuracy in forecasting the weekly photovoltaic energy production of the solar plant.

Increasing demand for food production with limited available water resources pose the threat to agricultural activities. The conjunctive allocation of water resources maximizes the net benefit of farmers efficiently. In this study, a novel hybrid optimization model was developed based on a genetic algorithm (GA), bacterial foraging optimization (BFO) and ant colony optimization (ACO) to maximize the net benefit of water deficit Sathanur reservoir command. The GA-based opti-mization model considered crop-related physical and economical parameters to derive optimal cropping patterns for three different conjunctive use policies and further allocation of surface and groundwater for different crops are enhanced with the BFO. The allocation of surface and groundwater for the head, middle and tail reach obtained from BFO is considered as input to ACO as a guiding mechanism to attain an optimal cropping pattern. Comparing the average produc-tivity values Policy 3 (3.665 Rs/m3) has better values relating to Policy 1 (3.662 Rs/m3) and Policy 2 (3.440 Rs/m3). Thus, the developed novel hybrid optimization model (GA-BFO-ACO) is very promising to enhance the farmer's net income as well as for the command area water conservation and can be replicated in other irrigated regions of the globe to overcome chronic land and water problems.

In the software development process, the decision-maker (DM) has a range of problems inherent to its function. Wrong choices during software planning can bring great risk to the project. Therefore, the planning of software releases to be delivered to the customer should be well done. This is not an easy task because releases are made up of many requirements that contain complex variables that must be considered, such as precedence, cost, requirement stability, among other features that make the requirements-selection process challenging. To make this process less exhaustive, DM can use tools that facilitate this work. In software engineering, we can find fields of research specialists in this context, such as Search-Based Software Engineering (SBSE). The SBSE makes use of advanced metaheuristics to search for optimal solutions or the closest to it. In this work, we try to use another field of research to solve this same problem type, the Verbal Decision Analysis (VDA). To do this, we elaborate a workflow that will use the same source data, execute two solutions using the two search fields (SBSE and VDA) and compare the results. In the end, we evaluated and commented on the results.

Wind power as a renewable source of energy, has numerous economic, environmental and social benefits. In order to enhance and control the renewable wind power, it is vital to utilize models that predict wind speed with high accuracy. Due to neglecting of requirement and significance of data preprocessing and disregarding the inadequacy of using a single predicting model, many traditional models have poor performance in wind speed prediction. In the current study, for predicting wind speed at target stations in the north of Iran, the combination of a multi-layer perceptron model (MLP) with the Whale Optimization Algorithm (WOA) used to build new method (MLP-WOA) with a limited set of data (2004-2014). Then, the MLP-WOA model was utilized at each of the ten target stations, with the nine stations for training and tenth station for testing (namely: Astara, Bandar-E-Anzali, Rasht, Manjil, Jirandeh, Talesh, Kiyashahr, Lahijan, Masuleh and Deylaman) to increase the accuracy of the subsequent hybrid model. Capability of the hybrid model in wind speed forecasting at each target station was compared with the MLP model without the WOA optimizer. To determine definite results, numerous statistical performances were utilized. For all ten target stations, the MLP-WOA model had precise outcomes than the standalone MLP model. The hybrid model had acceptable performances with lower amounts of the RMSE, SI and RE parameters and higher values of NSE, WI and KGE parameters. It was concluded that WOA optimization algorithm can improve prediction accuracy of MLP model and may be recommended for accurate wind speed prediction.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

Hybrid electric vehicles are certainly one of the key solutions for improving fuel efficiency and reducing emissions, especially in special vehicle application and with the use of CO2 neutral fuels. Determining the energy management strategy and finding the optimal solution with regard to the aforementioned goals re-mains the one of the main challenges in the design of HEV. This paper presents a new vehicle modeling method, with an emphasis on HEVs, which is based on the frequency analysis of emissions and consumption according to the current specific traction power of the vehicle. The evaluation of the newly introduced model in the RDE, NEDC and WLTP cycle was performed and the results were compared with the standard verified vehicle model that was created in AVL's CruiseM software package. Positive traction energies have positive deviations of between 0.35% and 2.85%. The largest deviation in CO2 emissions was recorded for the HEV model in the RDE cycle and in the non-hybrid model in the WLTP cycle of 3.79% and 4.4% respectively, all other combinations of cycle and vehicles had deviations of up to about 1%. As expected, the largest relative deviations were recorded for NOx emissions from 0.13% to 9.62% for HEV in the WLTP cycle.

We designed a bidirectional reflection distribution function (BRDF) measurement system to research the characteristics of space target materials. This system measures the BRDF data of an aluminum plate and gold foil. A hybrid biogeography-based optimization-firefly (BBO-Firefly) algorithm was proposed to optimize the five-parameter BRDF model. To check the performance of the hybrid BBO-Firefly algorithm, we set up a contrast experiment to optimize the BRDF parameters using the BBO algorithm, Firefly algorithm, and hybrid BBO-Firefly algorithm. The experimental results prove that the hybrid BBO-Firefly algorithm surpasses the BBO algorithm and Firefly algorithm in convergence speed and precision in the same situation and has a better optimization effect. Finally, we substitute the optimization results of the hybrid BPO-Firefly algorithm into the BRDF model to analyze the reflection characteristics of an aluminum plate and gold foil.

To predict the remaining useful life (RUL) of proton exchange membrane fuel cell (PEMFC) in advance, a prediction method based on the voltage recovery model and Bayesian optimization of a multi-kernel relevance vector machine (MK-RVM) is proposed in this paper. First, the empirical mode decomposition (EMD) method was used to preprocess the data, and then the MK-RVM was used to train the model. Then, the Bayesian optimization algorithm was used to optimize the weight coefficient of the kernel function to complete the parameter update of the prediction model, and the voltage recovery model was added to the prediction model to realize the rapid and accurate prediction of the RUL of PEMFC. Finally, the method proposed in this paper was applied to the open data set of PEMFC provided by FCLAB, and the prediction accuracy of the RUL of PEMFC was obtained by 95.35%, which showed that the method had good gen-eralization ability and verified the accuracy of the prediction for the RUL of PEMFC.

The path towards decarbonization requires a progressive adaptation of all refrigeration systems, but only stationary ones have been intensely studied to improve their environmental performance. However, refrigerated transport is a vital piece of the cold chain, and it must be considered in the green transition. In this paper, we propose a model for a hybrid refrigerated van that includes photovoltaic panels and electric batteries to decrease total greenhouse gas emissions from the engine. Thermal, electrical, and battery sub-models are considered and integrated into the comprehensive hybrid solar-powered refrigerated van model. Different technologies are compared in economic terms, including Lithium and Lead-acid batteries and three different types of photovoltaic panels. The model was validated regarding van fuel consumption, showing a 4% deviation. Single and multiple delivery scenarios are considered to assess the energetic, economic, and environmental benefits. Monthly CO2,e emissions could be reduced to 20% compared to a standard refrigerated van. Despite the environmental benefits provided by this sustainable solution, the payback period is still too long (above 20 years) because of the necessary investment to adapt the vehicle and considering fuel and electricity prices currently.

Accurate forecasting of wind power generation plays a key role in improving the operation and management of a power system network and thereby its reliability and security. However, predicting wind power is complex due to the existence of high non-linearity in wind speed that eventually relies on prevailing weather conditions. In this paper, a novel hybrid deep learning model is proposed to improve the prediction accuracy of very short-term wind power generation for the Bodangora Wind Farm located in New South Wales, Australia. The hybrid model consists of convolutional layers, gated recurrent unit (GRU) layers and a fully connected neural network. The convolutional layers have the ability to automatically learn complex features from raw data while the GRU layers are capable of directly learning multiple parallel sequences of input data. The data sets of five-minute intervals from the wind farm are used in case studies to demonstrate the effectiveness of the proposed model against other advanced existing models, including long short-term memory (LSTM), GRU, autoregressive integrated moving average (ARIMA) and support vector machine (SVM), which are tuned to optimise outcome. It is observed that the hybrid deep learning model exhibits superior performance over other forecasting models to improve the accuracy of wind power forecasting, numerically, up to 1.59 per cent in mean absolute error, 3.73 per cent in root mean square error and 8.13 per cent in mean absolute percentage error.

The city-port involves a decisive reality for the economic development of the territories and nations, capable of significantly influencing the conditions of well-being and quality of life, and of making the Circular City Model operational, preserving and enhancing seas and marine resources in a sustainable way, through the construction of appropriate production and consumption models, with attention to relations with the urban and territorial system. The Circular Economy paradigm identifies the ideal context in the city-port to rethink traditional development models and make ports driver areas for the regeneration of the city and metropolitan territories, in compliance with the EU Directive 2014/89 which considers maritime spatial planning as a tool for public authorities and stakeholders to achieve an integrated approach, promoting the development of maritime and coastal economies and the sustainable use of resources. The paper, starting from these assumptions, presents an adaptive decision-making process for the strategies development of the Naples (Italy) commercial port, aimed at re-establishing a sustainable city-port relationship and making operative Circular Economy principles.

This study addresses the implementation of the International Financial Reporting Standard 9 (IFRS 9) in the European Union as of January 1, 2018, replacing the International Accounting Standard 39 (IAS 39) to introduce a new model for recognizing Loan Loss Provisions (LLP) based on Expected Credit Loss (ECL). This model responds to criticisms of the former Incurred Credit Loss (ICL) system for its inability to reflect credit losses in a timely manner, potentially exacerbating the effects of financial crises (Bushman &amp; Williams, 2015; Gebhardt &amp; Novotny-Farkas, 2011). The study focuses on the effects of adopting the ECL model on the level of Loan Loss Allowances (LLA) in loans, own equity, and the Common Equity Tier 1 (CET1) ratio across 13 Portuguese commercial banks. A mean comparison test is used to evaluate scenarios before and after the application of the ECL model, highlighting the importance of regulator actions and the adequacy of loss recognition policies, including the effects of Regulation (EU) 2017/2395 of December 12. The results obtained demonstrate significant negative impacts on the net values of loans, own equity, and the CET1 ratio upon adopting the IFRS 9 ECL model, due to the widespread increase in LLAs.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

While some research supports utilizing plain radiography for measuring biomechanical alignment of the spine for prognosis and treatment, there are contrasting viewpoints regarding both the value and utilization of these procedures in conservative care. Evaluation of both conservative and non-conservative approaches to spinal care revealed vast differences in radiographic utilization and interpretation between orthopedic surgeons, primary care physicians, chiropractic physicians, and physical therapists, which may account for the different viewpoints and rationale in the literature. A research summary is provided regarding the various methods of spinal analysis utilized by these professions to help determine if there is any unique diagnostic or prognostic value associated with radiographic utilization that could assist in advancing conservative spinal assessment and treatment. Understanding any unique value provided through biomechanical assessment utilizing plain radiography of the spine established in the literature may help chiropractic physicians determine the appropriate use of radiographic procedures in clinical practice and how to coordinate efforts with other conservative and non-conservative professions to improve spinal healthcare.

Motivated by Autonomous vehicle idea and driving safety issues, driver assistance system such as Active braking, Cruise Control, Lane departure warning lane keeping and etc. has become a very active research area. However, this paper presents the performance and robustness analysis of a model predictive control and proportional integral derivative control for lane keeping maneuvers of an autonomous vehicle using computer vision simulation studies. A simulation study was carried out where a vehicle model based on single tracked bicycle model was developed in MATLAB/SIMULINK environment together with a vision dynamic system. Both PID controller and MPC were simulated to maintain the desired reference trajectory of the vehicle by controlling steering angle. Further performance and robustness analysis were carried out and the simulation results show that the proposed control system for the PID control achieved its objective even though it was less robust in maintaining its performance under various conditions like vehicle load change, different longitudinal speed and different cornering stiffness. While in the case of MPC the optimizer made sure that the predicted future trajectory of the vehicle output tracks the desired reference trajectory and was more robust in maintaining its performance under same conditions as in PID.