This study investigated different conditions for the hydrothermal co-liquefaction (co-HTL) of sugarcane bagasse and residual cooking soybean oil, with and without the presence of ethanol as a cosolvent to maximize the bio-crude yield. All co-HTL reactions were carried out in a 300 mL Parr® reactor at temperatures ranging from 200 to 300 °C. Bio-crude yields of around 95 wt.% were obtained at 300 °C using ethanol and water as solvents. The highest biochar yield (16.6 wt.%) was achieved when using only sugarcane bagasse as substrate, without the presence of soybean oil. Bio-crude samples obtained at higher temperatures (280 °C and 300 °C) using ethanol as a hydrogen donor presented higher contents of both free fatty acids and fatty acid ethyl esters. This work presents a promising process to produce high-quality bio-crude using an abundant feedstock (sugarcane bagasse) in the presence of a lipid source which could cause environmental problems if poorly handled.

To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.

The article presents a multiphase numerical computational fluid dynamics (CFD) for simulating hydrothermal liquefaction of sewage sludge in a continuous plug-flow reactor. The discrete particle method (DPM) was used to analyze the solid particle interaction in liquid-solid high shear flows to investigated coupling computational fluid dynamics (CFD) and discrete phase model (DPM) method. Increasing solid particles interaction were observed with increasing liquid velocity. The study examined the influence of parameters such as flow rate, temperature and residence time on the efficiency of bio-oil production. Furthermore, the trajectories of the solid particles are affected significantly by the ash flow and the solid particle size, thus the trajectories of particles resembles the streamlines. A parametric study is performed to investigate the effect of slurry flow rate, temperature and external heat transfer coefficient on the biocrude oil productions performance. This simulation data will be used in the future to design and scale up a large-scale HTL reactor.

This paper explores how smart cities can cope with land subsidence and liquefaction in the context of rapid urbanization in Japan. Since the 1960s, liquefaction has become an important topic in geotechnical engineering, and great efforts have been made to evaluate the resistance of soil to liquefaction. There is currently a lack of machine learning applications specifically for smart cities in areas such as geological hazards. This study uses two machine learning techniques, artificial neural networks and ensemble learning, to obtain a prediction model with high performance in predicting the bearing layer depth to improve the accuracy of geo-engineering surveys. The model was developed by analyzing actual survey data from 433 locations in Setegaya, Tokyo, by using artificial neural networks (ANNs) and bagging, respectively. The results show that machine learning has great advantages in predicting the bearing layer depth. In addition, compared with a single model such as artificial neural networks, the prediction performance of ensemble learning can be improved by about 20%. Both interdisciplinary approaches can help predict address risks and thus promote sustainable urban development, highlighting the potential of smart cities in the future.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

Amuyo Ponds (AP) are a group of three hydrothermal lagoons located at 3,700 m above sea level, in a pre-Andean setting at the Atacama Desert. Each pond shows a conspicuous green, red, or yellow coloration, and discharge waters rich in arsenic and boron into the Caritaya River (Camarones Basin, Arica and Parinacota Region, in northern Chile). Microorganisms at these ponds are subjected to harsh environmental conditions, and microbial composition and diversity in Amuyo Ponds sediments are unknown. Then, microbial life colonizing AP sediments was explored by metagenomics analyses. This approach showed a highly diverse microbial life dominated by members of the Bacterial Domain (nearly 800 bacterial genome sequences) and includes sequences associated to Archaea, Eukarya, and viruses. We also report putative functional capabilities related to virulence and defense genes, and biosynthesis of secondary metabolites. Thirteen bacterial and fourteen virus metagenome-assembled genomes were reconstructed and are here informed. This work expands our knowledge on the richness of microorganisms in AP and open further studies on the ecology and genomics of this striking Andean geosite.

In the present work report, the MgAl₂O₄and the Ag/MgAl₂O₄ samples were successfully synthesized by the modified hydrothermal and the isovolumetric impregnation methods, respectively. The structural properties of the prepared samples were systematically characterized by XRD, SEM, TEM, DRS, XPS and et al techniques. The photocatalytic degradation of methylene blue by the Ag/MgAl₂O₄ and MgAl₂O₄ samples was comparatively studied under UV lamp irradiation. The results revealed that the prepared Ag/MgAl₂O₄ (pH=6) samples were the most active among the samples in photocatalytic of methylene blue. Under UV lamp irradiation, the Ag/MgAl₂O₄ (pH=6) photodegradation of methylene blue reached to 89.6% within 120 min. And the Ag/MgAl₂O₄ (pH=6) complex photocatalysts displayed a high photochemical stability under repeated irradiation. Repeated irradiate the Ag/MgAl₂O₄ (pH=6) compound, which indicated it had a high photochemical stability.

Hazelnut shells (HS), scientifically known as Corylus avellana L. shells, are a waste produced in companies that process nuts. The main objective of this study was to find an efficient way to maximize the chemical potential of HS by solubilizing the hemicelluloses, which could then be used to recover sugars and at the same time increase the lignin content of this material in order to produce adhesives or high strength foams. In order to optimize the pre-hydrolysis process, two different temperatures (160 and 170 C) and times varying from 15 to 180 min were tested. All the remaining solid materials were then liquefied by polyalcohols with acid catalysis. The chemical composition of hazelnut shells was determined before and after the pre-hydrolysis. All the process was monitored by FTIR-ATR by determining the spectra of solids and liquids after pre-hydrolisis and liquefactions steps. The highest solubilization of hazelnut shells was found for 170 C and 180 min, resulting in a 25.8% solubilization. Chemical analysis after the hydrolysis process showed a gradual increase in the solubilization of hemicelluloses as both the temperature and time of the reactor were increased. Simultaneously, the percentages of α-cellulose and lignin in the material also increased with rises in temperature and duration. FTIR-ATR allowed for the detection of significant spectral changes in the hazelnut shells from their initial state to the solid residue and further into the liquefied phase. This confirmed that pre-hydrolysis was effective in enhancing the chemical composition of the material, making it more suitable for the production of adhesives or polyurethane foams with enhanced mechanical strength.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

The cultivation of pea pods spans across various regions and climates with a global production of around 20 million tons. The pea peel wastes, which make up 30–40% of the total weight of the peas, are freely available in large quantities. The biomass used was characterized via ultimate, proximate, and structural analysis obtaining a 20,2 %w of cellulose and 17,4 %w of hemicellulose which via valorization processes can be transformed into platform chemicals. Hydrothermal valorization presents itself as a clean form of treatment of said wastes, ranging from 120 – 180 ºC (LHW) to 180 to 260 ºC (HTC). The use of LHW can lead to the production of sugars (up to 70%w yield) and levulinic acid (4 %w yield) while the use of HTC leads to Formic acid (40 %w) and levulinic acid (4 %w yield). The use of LHW for longer times favors the production of HMF and Furfural. The use of homogeneous catalysts (H2SO4, CH3COOH, KOH and NaHCO3) was implemented and their selectivity described. Solid fractions of LHW and HTC were characterized via FTIR and elemental analysis and the change in their structure described as they shift from biomass to biochar. Optimal conditions for each platform chemical were reported for best utilization of the peapod waste.

Cruciferous vegetables represent a valuable source of bioactive compounds. However, there is currently a paucity of information regarding the extent to which these compounds remain bioavailable to the body following thermal treatment and digestion processes within the digestive tract. Accordingly, the aim of this study was to evaluate the impact of heat treatment and in vitro digestion on the level of selected bioactive compounds in Brussels sprouts. The Brussels sprouts samples were subjected to a range of thermal processing techniques, which were then followed by a simulated in vitro digestion. The investigated compounds were analysed using UV-Vis spectrometry and liquid chromatography coupled to mass spectrometry (LC-MS). The findings revealed that the sous-vide method of cooking Brussels sprouts resulted in significantly higher losses of glucosinolates (GLS) in comparison to conventional cooking methods. No significant differences were observed with regard to isothiocyanates and indoles. The analysis of GLS following digestion revealed that the process was more effective after sous vide and traditional cooking, and slightly less effective after steam cooking. With regard to individual compounds, glucoraphanin (GRA), glucoraphenin (GIV) and gluconasturtiin (GNS) were found to be completely degraded, whereas methoxyglucobrassicin (metGBS) was the most resistant to digestion in both the sous vide and steamed Brussels sprouts. The results indicated that the process of simulating digestion had no significant effect on isothiocyanates and indoles. This suggests that, if present in the heat-treated samples, these compounds remained stable during the in vitro digestion procedure.

Compared to the southern Tibetan Plateau, the northern part has been regarded as relatively lacking geothermal resources. However, there is no lack of natural hot springs exposed in beads along large-scale fracture systems, and research on them is currently limited to individual hot springs or geothermal systems. This paper focuses on the Wahongshan-Wenquan Fracture Zone (WWFZ), analyzes the formation of five hydrothermal activity zones along the fracture zone in terms of differences in the hydrochemical and isotopic composition of the hot water, and then explores the hydrothermal control of hot springs in the zone by the fracture. The results show that the main Fractures of WWFZ is the regional heat-control structures, and the fracture system formed by a small number of near-north-south and near-east-west fractures transversal to it provides a favorable channel for deep hydrothermal convective circulation. Ice and snow melt water from the Ngola Shan Mountains, with an average elevation of more than 4,500 meters above sea level, infiltrates along the fractures and is heated by deep circulation to form deep geothermal reservoirs. There is no detectable contribution of mantle source heat to the hot spring gases, and the heat source is mainly natural heat conduction warming, but the "Low-Velocity body (LVB)" in the middle and lower crust of the area may be the primary heat source of the high geothermal background in the area. The hydrochemical components of the hot springs in the area show a certain regularity, and the main ionic components, TDS and water temperature, tend to increase away from the main rupture, reflecting the controlling effect of the WWF on the hydrothermal transport in the area. In the future, the geothermal work in this area should focus on the hydrothermal control properties of different levels, the nature of fractures in the area, and the thermal contribution of LVB in the middle and lower crust.

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

The compositions of metalliferous sediments which is associated with hydrothermal vents can provide reliable geochemical indicators for the exploration of seafloor sulfides. In this study, surface sediments from the Xunmei hydrothermal field (HF) on the South Mid-Atlantic Ridge (SMAR) were selected, and their major and trace elements were analysed. The results showed that the sediments are composed of pelagic material (calcium biogenic components), basaltic debris, iron-manganese oxides, and a mixture of hydrothermal components. Additionally, the sediments were found to be significantly enriched in Cu, Zn, Fe and Co derived from hydrothermal sources, as well as Mn, V, Mo, U and P, which are primarily scavenged from seawater. The Cu and Zn concentrations are highest in the northeastern part of Xunmei, while the northeastern, northern, and southern parts are characterized by great inputs of hydrothermal Fe. Manganese and Mo are mainly enriched in the western and southern parts and show a strong positive correlation, indicating that Mo is mainly scavenged by Mn oxides. There are high positive correlations among U, P, and Fe, indicating their coprecipitation with Fe from hydrothermal plumes. Vanadium and Co are introduced into sediments in two ways, i.e., V is scavenged and coprecipitates from hydrothermal plumes, and Co is derived from sulfide debris. Based on the variations in Cu and Zn contents and in the Cu/Fe (0.159), Zn/Fe (0.158), and Fe/Mn (1440) ratios, it can be inferred that a high-temperature hydrothermal vent existed in northeastern Xunmei. In combination with the distribution patterns of the above elements, the hydrothermal vents in the southern part ceased erupting after a short period of activity. In addition, the high Mn anomaly and the high U/Fe ratios at the boundaries of the investigated area indicate the presence of a relatively oxidized environment in southwestern Xunmei.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

In response to increasing urbanization and the need for infrastructure resilient to natural hazards, this study introduces an AI-driven predictive model designed to assess the risk of soil liquefaction. Utilizing advanced ensemble machine learning techniques, the model integrates geotechnical and geographical data to accurately predict the potential for soil liquefaction in urban areas, with a specific focus on Yokohama, Japan. This methodology leverages comprehensive datasets from geological surveys and seismic activity to enhance urban planning and infrastructure development in smart cities. The primary outputs include detailed soil liquefaction risk maps that are essential for effective urban risk management. These maps support urban planners and engineers in making informed decisions, prioritizing safety, and promoting sustainability. The model employs a robust combination of neural networks and gradient boosting decision trees to analyze and predict data points, assessing soil susceptibility to liquefaction during seismic events. Notably, the model achieves high accuracy in predicting soil classifications and N-values, which are critical for evaluating soil liquefaction risk. Validation against an extensive dataset from geotechnical surveys confirms the model’s practical effectiveness. Moreover, the results highlight the transformative potential of AI in enhancing geotechnical risk assessments and improving the resilience of urban areas against natural hazards.

The objective of this study was to investigate the liquefaction resistance of chemically improved sandy soils in a straightforward and accurate manner. Using only the existing experimental databases and artificial intelligence, the goal was to make predictions without conducting physical experiments. Emphasis was placed on the significance of data from 20 loading cycles of cyclic undrained triaxial tests to determine the liquefaction resistance and the contribution of each explanatory variable. Different combinations of explanatory variables were considered. Regarding the predictive model, it was observed that a case with the liquefaction resistance ratio as the dependent variable and other parameters as explanatory variables yielded favorable results. In terms of exploring combinations of explanatory variables, it was found advantageous to include all variables as doing so consistently resulted in a high coefficient of determination. The inclusion of the liquefaction resistance ratio in the training data was found to improve the predictive accuracy. In addition, the results obtained when using a linear model for the prediction suggested the potential to accurately predict the liquefaction resistance using historical data.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

This paper presents the life cycle assessment results of a study of plastic recycling via hydrothermal upgrading (HTU), a chemical recycling technology. It was investigated due to its potential to address current gaps in the plastic recycling system, largely due to several plastic packaging materials and formats that cannot be processed by traditional mechanical recycling technologies (primarily due to technoeconomic reasons). As society transitions towards a net-zero-based circular economy, assessments should be conducted with a futuristic outlook, preventing costly mistakes by employing the right technologies in the right areas. HTU can generate up to 76% reduction in climate change impacts when compared with comparable end-of-life treatment technologies whilst conserving material with the system. Additionally, further reductions could be achieved by changes in electricity consumption within the study. This represents a new insight to chemical recycling of polymers by establishing a prospective life cycle assessment study that looks to introduce a step-change in the recycling system. By creating a transparent cut-off model with consistent allocation, it highlights the benefits of introducing this technology as opposed to the current model of disposal through incineration or landfill.

Based on the 5.7-magnitude earthquake that stroke Songyuan (China) and 172 groups of liquefaction data collected in mainland China, the hyperbolic liquefaction discriminant formula originally proposed by Sun Rui was revised, and a new formula for the liquefaction of sand was put forward. Groups of data derived from the Bachu earthquake in Xinjiang and an earthquake that occurred in New Zealand (47 and 195 groups, respectively) were used to carry out a back-judgment test, then, the results were compared with those of the existing standard method. Overall, the results showed that the new formula for hyperbolic liquefaction discrimination compensates for the conservative liquefaction discrimination of the older formula; moreover, it has a good applicability to different intensities, groundwater levels, and the deep sand layer of the Songyuan site, reflected by a more balanced success rate. Therefore, combining the existing liquefaction discrimination methods and the research results of discrimination, it is necessary to establish a suitable regional identification method through the continuous accumulation of liquefaction data and expanding database.

Liquefaction risk assessment is critical for the safety and economics of structures. As the soil strata of Ramsar area in north Iran is mostly composed of poorly graded clean sand and the ground water table is found at shallow depths, it is highly susceptible to liquefaction. In this study, a series of isotropic and anisotropic consolidated undrained triaxial tests are performed on reconstituted specimens of Ramsar sand to identify the liquefaction potential of the area. The specimens are consolidated isotropically to simulate the level ground condition, and anisotropically to simulate the soil condition on a slope and/ or under a structure. The various states of soil behavior are studied by preparing specimens at different initial relative densities and applying different levels of effective stress. The critical state soil mechanics approach for identifying the liquefaction susceptibility is adopted and the observed phenomena are further explained in relation to the micro-mechanical behavior. As only four among the 27 conducted tests did not exhibit liquefactive behavior, Ramsar sand can be qualified as strongly susceptible to liquefaction. Furthermore, it is observed that the pore pressure ratio is a good indication of the liquefaction susceptibility

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

Adopting banana peel as raw material, the adsorption properties of banana peel hydrothermal carbon modified with KOH solution for lead ions in aqueous solution were studied. The surface structure and functional groups of the modified hydrothermal carbon were analyzed by XRD and SEM. The results showed that the banana peel hydrothermal carbon prepared from 0.5 mol/L KOH solution had large pores, and its adsorption capacity reached 42.92 mg/g at a pH value of 6; When the concentration of KOH solution is 0.5 mol/L, the solid liquid ratio is 2 g/L, the adsorption capacity reaches 21.39 mg/g, and the adsorption rate reaches 82.74%; When the concentration of lead solution increased to 100 mg/L, the adsorption capacity of modified hydrothermal carbon for lead ions decreased to 78.26%; The equilibrium adsorption time of lead ion in solution on phosphoric acid modified hydrothermal carbon from banana peel was 250 minutes, and the adsorption process met the quasi second order kinetic model and Freundlich isotherm equation, with an equilibrium adsorption rate of 88.62%. The adsorption of lead ions in solution by KOH modified hydrothermal carbon is mainly chemical physical adsorption.

In this paper, mineralogical and elemental geochemical characteristics of massive sulfide samples collected from Jade hydrothermal field, located in the Izena depression in the central graben of Okinawa Trough, were analyzed by means of optical microscopy, scanning electron microscopy and electron probe. The results show that the sulfide in Jade hydrothermal area can be divided into Zn-Cu-Pb rich massive sulfide and Zn-Fe rich massive sulfide. The former is composed of sphalerite, galena, anglesite, chalcopyrite and pyrite, and its formation stage can be divided into pyrite stage, sphalerite-chalcopyrite stage, anglesite stage and colloidal pyrite stage. The latter is mainly composed of sphalerite, pyrite, marcasite and a small amount of galena, which can be divided into galena stage, pyrite stage, sphalerite stage, pyrite and marcasite stage. Cu and Zn in pyrite may exist in the form of microinclusions, while Ag and Pb may exist in pyrite in the form of fine galena inclusions containing Ag. Fe and Cu may enter sphalerite in the form of ion replacement. Zn may enter chalcopyrite in the form of ion replacement, and As and Pb may be inclusions in chalcopyrite as As-bearing galena inclusions. Consistent with the previous understanding, the metal elements in the hydrothermal liquid system in Jade hydrothermal field mostly migrate with the hydrothermal fluid as sulfur complexes, and when the hydrothermal fluid mixes with seawater, the physical and chemical conditions of the fluid change, resulting in sulfide mineral precipitation. However, the chemical structure of chalcopyrite is still controversial, which restricts the understanding of the substitution mechanism of trace elements during chalcopyrite precipitation.

Abiogenic hydrocarbons are fundamentally important for understanding the deep microbial communities and the origin of life. The generation of abiogenic hydrocarbons was proposed to be limited to ultramafic-hosted hydrothermal systems, fueled by the serpentinization product H₂. Here, we present the discharge of short-chain alkanes from an andesitic rock-hosted Lutao geothermal field in the north Luzon arc, carrying abiotic chemical and isotopic signals. These abiogenic hydrocarbons were generated from CO₂-H₂O-rich fluid inclusions, where the long-term storage since Lutao volcanism (~ 1.3 Ma) allowed overcoming the sluggish kinetics of CO₂ to CH₄ reduction at temperatures of 174 - 206 ^oC. Natural abiogenic production of hydrocarbons, therefore, can be more ubiquitous than previously thought. The hypothesis regarding the origin of methane in Earth’s early atmosphere and its implication to the origin of life may require reconsideration.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

Hydrothermal carbonization of cellulose was examined at 240 ℃ for 1 h. Ammonium sulfate and thiourea were selected as the doping sources of inorganic nitrogen and organic nitrogen for the preparation of supercapacitor carbon. The effect of boric acid on the properties of the resulting hydrochar after KOH activation was examined. The results showed that the proportion of functional groups and the specific surface area of the activated hydrochar would be reduced after the addition of boric acid, and the pore-forming process of the micropores would be inhibited. The hydrochar obtained from the reaction of cellulose and organic nitrogen compounds had better pore size distribution and electrochemical properties after activation. The largest specific surface area (952.27 m2 g-1) was obtained when only thiourea was used as the only doping source. In the three-electrode system, the specific capacitance resulting activated hydrochar reached 236.25 F g-1 at a current density of 1 A g-1. After 20,000 cycles of charging and discharging at a current density of 10 A g-1, the capacitance retention rate reached 99.96%. Therefore, this study proves that the supercapacitor carbon with good electrochemical properties could be obtained by the direct reaction of cellulose with organic nitrogen compounds.

Zeolitic imidazolate frameworks (ZIFs) have potential for various gas and ion separations due to their well-defined pore structure and relatively easy fabrication process compared to other metal-organic frameworks. As a result, many reports have focused on preparing polycrystalline and continuous ZIF layers on porous supports. In this study, we investigated how humidity and chamber temperature influence the structure of a ZIF-8 layer prepared by the hydrothermal method. We controlled the chamber temperature (ranging from 50 °C to 70 °C) and relative humidity (ranging from 20 % to 100 %) using a thermos-hygrostat chamber. We found that as the chamber temperature increased, ZIF-8 preferentially grew into particles rather than forming a continuous polycrystalline layer. By measuring the temperature of the reacting solution based on chamber humidity, we discovered that the heating rate of the reacting solution varied with humidity, even at the same chamber temperature. At higher humidity, thermal energy transfer was accelerated as water vapor delivered more energy to the reacting solution. Therefore, a continuous ZIF-8 layer could be formed more easily at low humidity ranges (ranging from 20 % to 40 %), while micron ZIF-8 particles were synthesized at a high heating rate. Our findings suggest that controlling the heating rate of the reacting solution is critical to preparing a continuous ZIF-8 layer, particularly for future scale-up of ZIF-8 membranes.

Resides derived from liquefaction of oil palm trunk in the presence of polyhydric alcohol with different liquefaction temperature and time were characterized to provide a new approach to understand some fundamental aspects of the liquefaction reaction. Higher temperature and longer reaction time resulted in lower residue content, indicating more decomposition of components of oil palm trunk. The amorphous polymer comprised of lignin, hemicellulose, starch, and cellulose with non-crystalline structure are firstly degraded at low liquefaction temperature, followed by the decomposition of crystalline region of cellulose. Although it was relatively difficult to destroy the ordered structure of cellulose, most of them could be liquefied via prolonging reaction time or enhancing reaction temperature. Nevertheless, it was found that re-condensation of liquefied products occurred during the liquefaction process when higher temperature of 180 oC was used after 60 min, leading to the gradual increase of residue content with increase of reaction time.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

Hydrothermal /super critical processes are important process to synthesize materials which are otherwise difficult to form under normal conditions. A mathematical model is developed using standard transport equations to calculate the time for heating of hydrothermal reactor and computer simulation of the model was carried out in SOLIDWORKS® to validate it. The materials used to form reactor vessel were stainless steel (outer body) and TEFLON (PFA) (inner vessel). It was shown that composite wall, its geometry, construction & properties greatly affect the time and pattern of heat transfer. The time calculated and pattern generated were found to be in good agreement with experimental values.

In the present study, we have followed the hydrothermal path for the synthesis of gold nanoparticles (Au NPs) from the biomaterial Elaeocarpus ganitrus seeds extract, which is a rapid, eco-friendly, non-chemical way. The prepared NPs were thoroughly analyzed by PXRD & HR-TEM studies and also tested for photocatalytic dye degradation and anticancer studies. Besides, antioxidant, antibacterial and anticancer properties of Au NPs were studied. In vitro studies revealed the dose-dependent cytotoxic effect of Au NPs. The prepared nanoparticles showed good cytotoxic impact against Prostate cancer (PC-3) cells line. The results of the present study could contribute to synthesize new and cost-effective drugs from Elaeocarpus ganitrus seeds extract by using bio approach.

In this study, we evaluate the nonlinear dynamics of convection flow using the thermodynamic variational principle, focusing on scenarios where multiple external forces, such as a thermal gradient and rotational field, are applied to a shallow annular pool. We observed that with the increase in the thermal gradient, the flow changed from an axial flow to a rotational oscillatory flow with the wave amplitudes aligned. Further increasing the temperature difference led to a rotational oscillatory flow characterized by alternating wave generation and annihilation. Our analysis of the flow, considering heat fluxes orthogonal to the thermal gradient, allowed us to describe the flow state as a phase at equilibrium. The state transition of the flow was accompanied by a discontinuous jump in the heat flux, which occurred at the intersection of the entropy production curves.

In order to study the hydrothermal behavior of cotton fiber, the carbonization process and structural evolution of discarded cotton fiber (WCF) under hydrothermal conditions were discussed use microcrystalline cellulose (MCC) and glucose as model compounds. The results showed that high temperature was beneficial to the hydrolysis of discarded cotton fiber, and the yield of the sugar was 4.5% which was lower than that of MCC 6.51%. WFC and MCC are carbonized in 240~260 ℃ and 220~240 ℃ respectively, while the carbonation temperature of glucose is lower than 220 ℃. The quality ratio of C/O in WCF and glucose hydrothermal products is 5.79 and 5.85 respectively; three kinds of hydrothermal carbonization products have similar crystal structure and oxygen-containing functional groups, and the WCF carbonization products contain a lot of irregular particles while the main products of glucose carbonization are 0.5 μm carbon microspheres (CMCC). The results show that glucose is an important intermediate product of WCF hydrolysis carbonation, and there are two main paths of cotton fiber hydrothermal carbonization: some cotton fibers are completely hydrolyzed into glucose and the nucleation is formed, and then the carbon microspheres are grown; for the other part, the glucose ring of the polysaccharide oligosaccharide formed by the incomplete hydrolysis of cotton fiber in the hydrothermal environment of high temperature and pressure breaks, then forms the particulate matters.

A comprehensive 3D Multiphysics model was developed to simulate a plate fin heat exchanger designed for hydrogen liquefaction, incorporating ortho-para- hydrogen conversion catalyst in the hot fin channel. The model encompassed the 3D serrate fin structure, turbulent flow within the cold fin channel, and porous flow through the catalytic hot fin channel. Species transportation within the hot fin channel is coupled with ortho-para hydrogen conversion kinetics, while heat transfer mechanisms between the hot and cold fin channels are rigorously accounted for. Addi-tionally, the state- of- art equation of state is employed to accurately describe the thermodynamic properties of ortho- and para- hydrogen within the model. Numerous operational parameters, including the gas hourly space velocity, cold gas velocity, ortho-para- hydrogen conversion ki-netics, and operating pressure, were systematically varied to identify the kinetic and heat transfer constraints during the heat exchanger operation. The findings revealed that the ortho-para- hy-drogen conversion kinetic parameter predominantly governs operations requiring high gas hourly space velocity, particularly in large- scale hydrogen liquefaction processes. Furthermore, significant pressure drop within the catalytic filled channel was observed, however, operating at higher pressure mitigates this issue while mildly enhancing ortho-para-hydrogen conversion kinetics.

The aim of this study is to present a method for developing fragility curves for soil liquefaction that are consistent with the seismic hazard using Monte Carlo simulation. This method can account for all the uncertainties and variabilities of the input parameters. The seismic parameters of earthquake magnitude (M) and the associated peak ground acceleration (PGA) are considered together for the liquefaction assessment. The liquefaction potential and damages obtained by this method are more realistic. A case study is performed using data from a sand-boil site in Yuanlin, Changhua county, where liquefaction occurred during the Chi-Chi earthquake in Taiwan in 1999. The results show that the liquefaction potential index, IL, the post-liquefaction settlement, St, and the liquefaction probability index, PW, are all suitable parameters for evaluating the liquefaction damages. The fragility curves for soil liquefaction developed by this method can support the performance-based earthquake engineering (PBEE) approach, provide guidance for liquefaction evaluation to the ‘Taiwan Earthquake Loss Estimation System’-TELES, and serve as a basis for scenario simulation and an earthquake early warning system for liquefaction damages.

Knowledge about the liquefaction vulnerability in Pariaman city which is prone to an earthquake is very much needed in disaster mitigation based spatial planning. The liquefaction is an event of loss of the strength of the sandy soil layer caused by the vibration of the earthquake, where the liquefaction occurs in the sandy soil layer which has loose material in the form of sand that is not compact or not solid. This research was conducted by analyzing the potential of liquefaction vulnerability based on the Conus penetration to produce Microzonation of the susceptibility of subsidence due to liquefaction at 4 locations in Pariaman city, i.e., Marunggi village, Taluak village, Pauh Timur village and Padang Birik-Birik village. The Conus penetration testing is carried out using the piezocone (CPTU) method and mechanical Cunos penetration, and approach using Geographic Information System (GIS). The results showed that the potential of liquefaction was found at the sandy soil layer of sand and a mixture of sand and silt, which is characterized by the value of Cunos resistance and local resistance each smaller than 15 MPa and 150 kPa at varying depths. Based on the results of the analysis using this method, the critical conditions of liquefaction found in the medium sandy soil to solid. The fine sand layer which has the potential for liquefaction is in sand units formed from coastal deposits, coastal ridges and riverbanks. This liquefaction vulnerability zones analysis is limited to a depth of 6.00 m due to the limitations of the equipment used. The results of the analysis show that the fine sand layer which has the potential for liquefaction occurs at a depth of> 1.00-6.00 m with the division of zones, i.e., 1) High liquefaction in the sandy soil layer which has a critical acceleration (a) <0.10 g with shallow groundwater surface; 2) Medium liquefaction in the sandy soil layer which has a critical acceleration (a) between 0.10–0.20 g with shallow groundwater surface; and 3) Low and very low liquefaction in the sandy soil layer which has a critical acceleration (a) between 0.20–0.30 g with an average groundwater deep enough surface.

Biowaste management is in the center of attention in recent years, due to the increased focus on Circular Economy practices. Recent management solutions promote exploration for small and medium scale processing and monitoring practices. In this context, two pathways of biowaste valorization are analyzed: composting and anaerobic digestion. This study focuses on energy production with the hydrothermal carbonization (HTC) of anaerobic residues from biogas production. Lesvos has numerous processing facilities and olive mills, and therefore Olive Mill Wastewater (OMWW) are the main biowaste streams in the island, along with olive tree pruning, the organic fraction of municipal solid waste and sludge from wastewater treatment facilities. Most studies present applications on specific types of biowaste, while this study aims to co-treat several biowaste streams. A holistic experimental set-up that combines aerobic and anaerobic treatment strategies was developed taking into consideration the hydrothermal treatment of AD digestate along with locally available biowaste, like OMWW, sludge etc. A main target objective is to investigate if solid fraction could have a high heating potential In addition, HTC was able significantly to reduce the COD of OMWW while resulting in hydrochars with increased heating values.

This article discusses the results of fluid inclusions study in barite collected at the Jan Mayen vent field area (Troll Wall and Perle &amp; Bruce) and Loki’s Castle vent field of the Mohns Ridge segment of the Arctic Mid-Ocean Ridge. Three mafic-hosted volcanogenic massive sulfide deposits were examined within the active vent fields that adequately correspond to geological settings of ultraslow-spreading ridges and PT-conditions. Hydrothermal sediments were investigated to determine the temperature and salinity of the fluids responsible for barite precipitation. The hydrothermal origin of the barite was confirmed by its morphology. Fluid inclusions are two-phase and homogenized into the liquid phase on heating at temperatures below 287ºC. The salt concentration in fluids trapped in inclusions is 2.6–4.4 wt.% NaCl eq. The crystallization temperatures varied from 276ºС to 119ºС and from 307ºС to 223ºС for the Jan Mayen and Loki’s Castle vent fields, respectively. The data obtained allowed us to confirm evidence of fluid phase separation in the hydrothermal systems and to expand our knowledge of the temperature and salinity of mineral fluids previously known from recent direct measurements during the cruises within the G.O. Sars research vessel. The fluid inclusions data obtained from barites emphasize the fluid features characteristic of volcanogenic massive sulfide deposits, the similarities and differences for the studied hydrothermal sites, and allow comparisons with similar products from other active hydrothermal systems.

Synthesis of activated carbon from waste biomass is of current interest towards sustainability. The properties of biomass derived activated carbon largely depends on the carbonization process. This study reports preparing extremel high surface area mesoporous activated carbon from hemp bast fibre using hydrothermal processing. Processing in hot water (390-500^oC), then activation using KOH and NaOH was investigated at different loading ratios. The described approach was found to enhance the mesoporosity (centered at 3.0 to 4.5 nm) of the hemp derived activated carbon (HAC) from activation (confirmed by BJH pore size distribution and TEM imaging). BET results showed that the product has an extremely high surface area (2425 m²/g) while the surface functional groups (-OH, COOH, C=C/C-C) were confirmed and quantified by XPS and FTIR results. Increasing KOH concentration was found to enhance the surface area with an optimum biochar to KOH ratio of 1:3. The crystallite domain size of HAC was determined using Raman spectroscopy of different wavelengths. The procedure described in this study is an environmentally friendly scalable route for the mass production of activated carbon using hemp fiber.

Highly photoluminescent C-Dots are prepared by hydrothermal reaction of citric acid and piperazine as dual reason in both hydrolysis and surface passivation agent along with the N-doping agent. The resulting C-Dots without external passivation showed PL enhancement by electron transfer from C-Dots-donor to piperazine-acceptor with the maximum emission yields of more than 84%. After mixing the prepared C-Dots with the mixture of EtOH and acetone (1:1 vol %), a novel washing process was performed by centrifugation to remove the precursors and by-products. The resulting C-Dots showed much better stability than dialysis. For evaluating the possible application of the C-Dots as a fluorescent biological probe which possess the wide dosing window and multicolor properties. The C-Dots were localized in perinuclear vacuole-like structures with granular pattern in cytoplasm sparing the nucleus. No signs of any morphological deterioration like nuclear shrinkage were observed.

A hydrothermal pretreatment of the microalga Nannochloropsis gaditana at mild temperatures has been studied in order to reduce N and O content in the biocrude obtained by hydrothermal liquefaction (HTL). The work is focused on the evaluation of temperature, reactor loading and time (factors) to maximize the yield of the pretreated biomass and the heteroatom contents transferred from the microalga biomass to the aqueous phase (responses). The study followed the factorial design and response surface methodology. An equation for every response has been obtained, which leads to the accurate calculation of the operating conditions required to obtain a given value of these responses. Temperature and time are critical factors with a negative effect on the pretreated biomass yield, but a positive one on the N and O recovery in the aqueous phase. The slurry concentration has to be low to increase heteroatom recovery and high to maximize the pretreated microalga yields

Recent advances and demands in clinical applications drive a large amount of research to hydroxyapatite (HA) composite coatings fabricated by plasma spray. However, lower degree of HA crystallinity related to high temperature exposure in plasma spray usually leads to rapid weakening and disintegration of HA coatings and often promotes inflammatory responses in the surrounding tissue. In this research, graphene nanosheet (GNS) reinforced HA coatings were fabricated using plasma spray and followed by heat and hydrothermal treatment (hereafter referred to as thermal treatment). The addition of GNSs resulted in competing phenomenon to influence HA crystallinity viz. increased portion of the partially melted/unmelted zones and higher cooling rate during splat formation, leading to slight increase in HA crystallinity (~46.0-51.3%) in the as-sprayed coating. XRD and FTIR results showed that thermal treatment was capable of inducing significant transformation of amorphous HA to the crystalline form and removing other foreign non-HA compounds through regaining OH- ion, and therefore HA coatings displayed ~45.5-47.1% improvements in HA crystallinity regardless of addition or not of the GNS nanofillers. Microstructure observations revealed that thermal treatment enabled microcrack propagation due to stresses caused by crystallisation and phase transformations, and the residual partially melted/unmelted zone of the thermally treated GNS/HA coating was significantly decreased in size. More importantly, the added GNSs contributed greatly to the significant increase in surface nanoroughness of the thermally treated HA coatings owing to the fact that much more structural defects along with the GNSs mainly induced by thermal treatment might act as nucleation sites to accelerate HA nanoparticle precipitation, which would be beneficial for the improved adhesion strength of the osteoblast cells on the coating surface.

Listwaenite rocks are widely spread in Fenja area of the Semail ophiolite of Oman and in Islam Abad area of the Neyriz ophiolite of Iran. There are three types of listwaenites found in these regions: silica-, carbonate-, and carbonate-silica (which includes dolomite, calcite, and magnesite. The alteration of host harzburgites started with hydrothermal alteration to serpentinite, followed by carbonation and silicification of serpentinite. Calcite- and magnesite-dolomite- listwaenites are more abundant in the Fenja area of Oman, while dolomite-listwaenites are more abundant in Islam Abad area in Iran. The mineralogy of listwaenites varies in both Iran and Oman; common minerals include quartz, calcite, goethite, magnesite, dolomite, serpentine, hematite, magnetite, Cr-mica, and Cr-spinel The major element chemistry of the different types of listwaenites in both Fenja and Islam Abad area generally comparable, and is largely similar to that of hydrothermally carbonated harzburgites, serpentinite, and listwaenites worldwide, despite spanning extraordinary and highly variable contents in major oxides, such as CaO, SiO2, MgO and LOI. Relict texture and common occurrence of Cr-spinel as well as the high concentrations of Cr, Ni and Co suggest that the protolith of the listwaenites in both regions was serpentinized harzburgites and serpentines. In comparison to the primary mantle and chondrite in spider diagrams, the Neyriz listwaenites have higher trace and REE element abundances than comparable listwaenites in the Fenja region. Harzburgite-normalized patterns of trace elements and REE in serpentinite and listwaenites overlap the average composition of harzburgite. PM-normalized trace element and REE patterns for serpentinized harzburgite and serpentinite show enrichment in Cs, U, Pb and Sr, with no Eu anomaly, comparable to mantle wedge serpentinites. The variable and high abundances of Ca, Mg, Ba, Zr, Sr, Pb, Zn, Mo and W in the carbonate- and silica-carbonate listwaenites, with unique Si enrichment and Mg, Na2O, Zr, Y, Ba, Sr, Rb, Cu, Pb, Sc, Cs, Nb, Mo and W. depletion in silica listwaenites are indicative of large fluctuations in major and trace element mobility. Cr, Ni and Co were immobile during alteration Enrichment in Ca and Si could occur by internal or late outside supply. Ca, Mg and Si are conceivably the foremost mobile major components amid harzburgite and serpentinite carbonation with mobilization confirmed by formation of quartz and Mg-carbonate in silica-carbonate listwaenites and quartz in silica listwaenites. The listwaenites in Islam Abad and Fenja area were formed due to hydrothermal alteration of serpentinite along thrust faults and shear zones which acted as pathway for Ca and/or Si rich fluids. The intensity of deformation in Islamabad listwaenites has been higher than Fenja listwaenites as indicated by higher abundance of trace elements.

This article describes the synthesis of hydroxyapatite (HAp) flakes through a microwave-assisted hydrothermal method. These flakes are intended for use as substrates for depositing titanium dioxide (TiO2) films using chemical vapor deposition with metal–organic precursors (MOCVD). The results reveal the formation of crystalline hydroxyapatite characterized by a uniform mor-phology. Additionally, we demonstrated the successful deposition of TiO2 coatings on the hy-droxyapatite flakes, resulting in a distinctive faceted prism morphology. Our findings affirm the effective synthesis of the HAp/TiO2 composite material. To further explore the material’s practical applications, we recommend assessing the photocatalytic activity of these composite membranes in future research.

The study of hydrothermal travertines contributes to the understanding of the interaction between physico-chemical processes and the role played by microbial mats and biofilms in influencing carbonate precipitation. Three active travertine sites were investigated in Central Italy to identify the types of carbonate precipitates and the associated microbial mats at varying physico-chemical parameters. Carbonate precipitated fabrics at the decimetre- to millimetre-scale and microbial mats vary with decreasing water temperature: a) at high temperature (55-44°C) calcite or aragonite crystals precipitate on microbial mats of sulphide oxidizing, sulphate reducing and anoxygenic phototrophic bacteria forming filamentous streamer fabrics, b) at intermediate temperature (44-40°C), rafts, coated gas bubbles and dendrites are associated with Spirulina cyanobacteria and other filamentous and rod-shaped cyanobacteria, c) low temperature (34-33°C) laminated crusts and oncoids in a terraced slope system are associated with diverse Oscillatoriales and Nostocales filamentous cyanobacteria, sparse Spirulina and diatoms. At the microscale, carbonate precipitates are similar in the three sites consisting of prismatic calcite (40-100 µm long, 20-40 µm wide) or acicular aragonite crystals organized in radial spherulites, overlying or embedded within biofilm EPS (Extracellular Polymeric Substances). Microsparite and sparite crystal size decreases with decreasing temperature and clotted peloidal micrite dominates at temperatures &lt; 40°C, also encrusting filamentous microbes. Carbonates are associated with gypsum and Ca-phosphate crystals; EPS elemental composition is enriched in Si, Al, Mg, Ca, P, S and authigenic aluminium-silicates form aggregates on EPS. This study confirms that microbial communities in hydrothermal travertine settings vary as a function of temperature. Carbonate precipitate types at the microscale do not vary considerably, despite different microbial communities suggesting that travertine precipitation, driven by CO2 degassing, is influenced by biofilm EPS acting as template for crystal nucleation (EPS-mediated mineralization) and affecting the fabric types, independently from specific microbial metabolism.

This study identifies the facies and degrees of hydrothermal alteration related to the low sulphida-tion epithermal Kestanelik Au deposit in the Biga Peninsula metallogenic province through petro-graphic studies and analysis of geochemical characteristics, such as mass changes, molar element ratios, and alteration indices. The gold mineralization is located in silicified zones containing veins and stockwork veinlets of quartz. These zones are found within the Permian-Upper Cretaceous aged Çamlıca basement metamorphics and Eocene aged Kestanelik granodiorite of the Karabiga Massif on the Biga Peninsula. The mineralization is influenced by tectonic structures such as quartz veins and faults. In the Kestanelik Au deposit, common hydrothermal alteration occurs mainly in the metamorphics and granodiorite, and less often in volcanic rocks. Based on miner-alogical and geochemical studies conducted on altered samples, four different alteration facies were defined as silicic, sericitic, argillic and propylitic, which show remarkable differences in the behaviour of REE, Si, K, Al, Na and Ca elements. The characterization of rocks subjected to hy-drothermal alteration that are most influenced by diverse K metasomatism with the largest K gains and losses of Na-Ca, is illustrated by molar element ratio plots. Depending on the severity of K-metasomatism, gold mineralization rises with increasing K trends towards gold ore veins. In the Kestanelik Au field, the alteration types of argillic, sericitic, propylitic and adularia from the alter-ation zones enclosing the Au ore veins, were revealed by the alteration index and chlo-rite-carbonate-pyrite index. Mass changes in the altered rocks indicate that there are gains in Si, K, Al, and losses in Na and Ca with the increasing intensity of alteration towards the Kestanelik ore veins. The results confirm the presence of silicic and K-metasomatic (sericite and argillic) propylit-ic (Fe-rich chloride) alteration zoning extending from the inner regions to the outer regions, which characterize the epithermal ore systems. It has been revealed from the data obtained in this study that the intensity of potassium metasomatism that occurs in acidic rocks is greater than that found in intermediate and mafic rocks. The hydrothermal fluids that cause alteration in Kestanelik Au mineralization and host rocks had low contents of REE due to REE mobilization, and the kaolini-zation of feldspars and micas, and the chloritization of biotite and feldspars, may cause negative Eu anomalies.

Quarry waste fines and eggshells are unavoidable wastes which relentlessly contribute to environmental load and pollution. Although a number of studies have suggested various methods for recycling, these wastes remain underutilized due to some technical constraints. In addition, no study has yet been explored on the possibility of combining quarry waste fines (QWF) and eggshell powder (ESP) for tobermorite synthesis. Tobermorite is the main component which primarily provides strength to the autoclaved aerated concrete products. For this purpose, this study seeks to evaluate the potential of QWF- ESP mix at 10%, 15% and 20% amounts of cement, respectively. The XRF, XRD, and TGA–DTA techniques were used to characterize the waste materials while physical and mechanical property tests and XRD analysis were performed on the autoclaved samples. It was found that QWF contains 53.77% SiO2, while ESP contains 97.8% CaO which are key components for tobermorite synthesis. This study also revealed that the mixture with only 10% cement has the highest compressive strength among the QWF-ESP samples. Furthermore, the formation of tobermorite in the samples was confirmed through XRD analysis. Hence, the hydrothermal curing of QWF –ESP can be further developed to produce functional tobermorite – bearing materials.

The use of low-cost, Remotely Operated Vehicle (ROV) and underwater photogrammetry techniques for 3D reconstruction of shallow hydrothermal vent sites around Paleochori Bay, Milos Island, Greece. Characterising venting fields through interactive bathymetry models produced from still images taken from camera onboard ROV flown over areas of interest in double raster pattern. First time the shallow venting fields on Milos have been actively surveyed using ROV. Areas were successfully surveyed and the bathymetry was reconstructed using SfM photogrammetry with a ~10 cm scale resolution. A diverse range of benthic habitats were surveyed and the resulting topographic models will act as a baseline, providing further characterisation of the vent systems and any evolving seafloor morphology associated with mineral deposition.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

Ferroelectric materials are crucial for today’s technological society, and nanostructured ferroelectric materials are important for downscaling of devices. Controlled and reproducible synthesis of these materials are therefore of immense importance. Hydrothermal synthesis is a well-established synthesis route, with a large parameter space for optimization, but a better understanding of nucleation and growth mechanisms is needed for full utilization and control. Here we use in situ X-ray diffraction to follow the nucleation and growth of BaTiO₃ formed by hydrothermal synthesis using two different titanium precursors, an amorphous titania precipitate slurry and a Ti-citric acid complex solution. Sequential Rietveld refinement was used to extract the time dependency of lattice parameters, crystallite size, strain and atomic displacement parameters. Phase pure BaTiO₃ nanoparticles 10 - 15 nm in size were successfully synthesized at different temperatures (100, 125, and 150 °C) from both precursors after reaction times ranging from a few seconds, to several hours. The two precursors resulted in phase pure BaTiO₃ with similar final crystallite size. Finally, two different growth mechanisms were revealed, where the effect of surfactants present during hydrothermal synthesis is discussed as one of the key parameters.

The generation of platform chemicals and hydrochar is of great interest because they reduce dependence on fossil resources and contribute to climate change mitigation by reducing carbon emissions. The main objective of this study was to evaluate the effect of biomass particle size and biomass water ratio in a hydrothermal conversion system for the generation of value-added products obtained from sugarcane bagasse. Biomass characterization was performed using proximal, elemental, and structural analysis; hydrothermal carbonization was carried out at 220 to 260 °C for one hour; and conversion was monitored using pH, conductivity, and IR spectroscopy. Platform chemicals were quantified by HPLC-IR. Hydrochars were characterized by scanning electron microscopy and energy dispersive spectroscopy. The results show that with a biomass:water ratio of 1:50 and a particle size of 212 μm at 220 °C, a yield of 31.07 % of platform chemicals was obtained on a dry basis. Likewise, the hydrochar with the highest carbon content and a higher porosity appearance was obtained with a biomass-to-water ratio of 1:50 and a particle size of 600 μm at 260 °C.

In recent decades, perovskite-type compounds (ABB′O3) have been exhaustively studied due to their unique ferroelectric properties. In this work, a systematic study aiming to prepare fine particles in the binary system SrZrO₃–SrTiO₃ was conducted under hydrothermal conditions in a KOH (5 M) solution at 200 °C for 4 h under a constant stirring speed of 130 rpm. The precursors employed were SrSO₄ powder (&lt; 38 μm size) and coprecipitated hydrous gels of Zr(OH)₄•9.64 H₂O (Zr-gel) and Ti(OH)₄•4.5H₂O (Ti-gel), which were mixed according to the stoichiometry of the SrZr_1-xTixO₃ in the compositional range of 0.0&gt;x&gt;100.0 mol% Ti⁴⁺. The XRD results revealed the formation of two crystalline phases rich in Zr⁴⁺, an orthorhombic structured SrZr0.93Ti0.07O3 and a cubic structured SrZr0.75Ti0.25O3 within the compositional range of 0.1–0.5 mol of Ti4+. A cubic perovskite-structured solid solution, SrTi1-xZrxO3, was preferentially formed within the compositional range of 0.5&gt;x&gt;0.1 mol% Ti⁴⁺. The SrZrO₃ and SrZr_0.93Ti_0.07O₃-rich phases had particle sizes averaging 3 m with a cubic morphology. However, a remarkable reduction in the particle size occurred on solid solutions prepared with hydrous Ti-gel over contents of 15 mol% Ti⁴⁺ in the reaction media, resulting in the formation of nanosized particles agglomerates with cuboidal shape self-assembled via a 3D hierarchical architecture, the sizes of these particles varied in the range between 141.0–175.5 nm. The limited coarsening of the particles is discussed based on the Zr-gel and Ti-gel dehydration capability differences that occurred under hydrothermal processing.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

Background: The tsunami and earthquake occurred in 1927 and 2018 made life quality of Da’a Tribe women in refugee camps was affected by violence. It affects on women reproductive health in various aspects of life as high maternal mortality rate of 450 per 100 thousand live births and half of women victims of natural disasters have reproductive health problems such as anemia and malnutrition during pregnancy. The study objective is to explore the health quality of women related to the couple violence during the humanitarian crisis at refugees’ camps. Method: The population was 798 cases of violence. The 90 samples were selected by simple random sampling and calculated by Slovin method. Data analysis was done by descriptive qualitative and cross tabulation. The research location was Palu City. Results: The research findings showed that health quality of Da’a Tribe women after the couple violence is influenced by three factors, namely economic by 40%, psychological by 7%, violence during pregnancy 59.3%. Conclusion: Social life and women violence handling can be done by symbolizing the threat of criminal law for male perpetrators in accordance with applicable laws in Indonesia and improving the life quality of population, especially women in education and skills through empowering the family economy and increasing gender equality justice.

In this study, unlike conventional methods for producing vanadium (3.5+) electrolyte by VOSO4 and V2O5, a batch-type hydrothermal reactor was used to produce a vanadium (3.5+) electrolyte for vanadium redox flow batteries through a reduction reaction. The starting material, V2O5, was mixed with different concentrations of citric acid (0.8M, 1.2M, 1.6M, 2.0M) as reducing agent and stirred using a hot plate at 90°C for 60 minutes to achieve complete dispersion in the solution. The resulting solution was then subjected to a hydrothermal reduction reaction in a furnace at 150°C for 24 hours to produce vanadium (3.5+). The mixed state of the produced vanadium (3+) and vanadium (4+) was confirmed using UV-vis spectroscopy. Electrochemical properties were investigated through CV analysis, confirming that the optimal concentration was 1.6M. Charge and discharge experiments were conducted to compare the current efficiency, energy efficiency, and voltage efficiency of the electrolyte prepared by the hydrothermal reduction process and the electrolyte prepared by VOSO4. As a result, the electrolyte produced through the hydrothermal reduction process showed improved performance in all efficiencies. The results shows that vanadium (3.5+) electrolyte could be easily produced through a reaction process using citric acid.

This research investigates the difference on the products obtained through two hydrothermal carbonization treatments. Our aim is to synthesize metal-free, carbon-based catalysts for the Oxygen Reduction Reaction (ORR) to serve as efficient and cost-effective alternatives to plati-num-based catalysts. Catalysts synthesized using the traditional hydrothermal approach exhibit a higher electrocatalytic activity for ORR in alkaline media, despite a more energy-intensive pro-duction process. The superior performance is attributed to differences in particle morphology and to the chemical composition of the particle surfaces. The presence of functional groups on the surfaces of catalysts obtained via traditional approach significantly enhances ORR activity by fa-cilitating deprotonation reactions in an alkaline environment. Our research aims to be a reference for future investigations, shifting the focus to the fine-tuning of surface chemical compositions and morphologies of metal-free catalysts to enhance ORR activity.

Ti and Ti alloys are materials usually used in contact with hard tissue for applications such as artificial joints and dental implants. Ti6Al4V is a very common alloy used for dental implants, owing to its good mechanical properties and corrosion resistance. Nevertheless, because of uncertainties regarding the toxicity of vanadium and its influence on the human body, other Ti alloys containing no vanadium and retaining suitable properties are used. In this work Ti6Al4V and Ti6Al7Nb were oxidized in a water solution of calcium acetate (Ca(CH3COO)2) and calcium glycerophosphate (Ca(PO4CH(CH2OH)2) by Plasma Electrolytic Oxidation (PEO) for 20 minutes and then were hydrothermally treated (HTT) in water (pH=7) and in potassium hydroxide (KOH) solution (pH=11) for 2 hours at 200°C in a pressurized reactor. The surface morphologies, elemental composition and phase components were characterized by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD), respectively. The surface roughness was measured by Atomic Force Microscope (AFM) and thickness measurements were made by SEM and thickness gauge. Also, corrosion tests were made to evaluate the corrosion behavior of the two alloys. The aim of this study is to compare two viable Ti alloys, Ti6Al4V and Ti6Al7Nb, and to attain on their surface hydroxyapatite (HA) coating improving the osseointegration, as it simulates a human bone.

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

Dayaoshan, as an important metal ore producing area in China, is faced with the dilemma of resource depletion due to long-term exploitation. In this paper, remote sensing method is used to circle the favorable metallogenic areas and find new ore points for Gulong. Firstly, vegetation interference bas been removed by using mixed pixel decomposition method with hyperplane and genetic algorithm (GA) optimization; then, altered mineral distribution information has been extracted based on principal component analysis (PCA) and support vector machine (SVM) method; Thirdly, the favorable areas of gold mining in Gulong has been delineated by using ant colony algorithm (ACA) optimization SVM model to remove false altered minerals; Lastly, field survey verified that the extracted alteration mineralization information is correct and effective. The results show that the mineral alteration extraction method proposed in this paper has certain guiding significance for metallogenic prediction by remote sensing.

Li₂TiO₃ nanopowders were synthesized by hydrothermal process using anatase TiO₂ and LiOH H₂O as raw materials. Li₂TiO₃ crystallizes in the layered monoclinic structure (space group C2/c) with average crystallite size of 34 nm. Morphology, elemental composition and local structure of products were carried out using HRTEM, FESEM, EDS, Raman and FTIR spectroscopy. Transport properties investigated by d.c. (4-probe measurements) and a.c. (complex impedance spectroscopy) show the activation energy of 0.71 and 0.65 eV, respectively. The ionic transport properties of Li⁺ ions in nanocrystalline Li₂TiO₃ characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) validate the good electrochemical properties of this anode material for lithium-ion batteries.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

The efficacy of weed management depends on the correct control timing according to the seedling emergence dynamics. Since soil temperature and soil moisture are two main factors that determine weed germination, the hydrothermal time model can be used to predict their emergence. The aim of this study was to estimate the base temperature (Tb) and base water potential (Ψb) for germination of Chenopodium album, Amaranthus retroflexus, Setaria pumila and Panicum capillare collected from fields in continental Croatia and then to compare these values with those of Italian populations embedded in the AlertInf model. Germination tests were performed at seven constant temperatures (ranging from 4 to 27°C) and eight water potentials (0.00 to - 1.00 MPa). Estimated Tb and Ψb were 3.4°C, -1.38 MPa for C. album, 13.9°C, -0.36 MPa for A. retroflexus, 6.6°C, -0.71 MPa for S. pumila and 11.0°C, -0.87 MPa for P. capillare, respectively. According to the criterion of overlap of the 95% confidence intervals, only Tb of C. album, and Ψb of A. retroflexus were similar between Croatian and Italian populations. Further field experiments should be conducted in the Croatian field to monitor weed emergence patterns of C. album and to calibrate the AlerInf equation parameters.

In the present study, the ability of novel carbon microspheres (CMs) derived from a date palm (Phoenix dactylifera) biomass using a hydrothermal carbonization (HTC) process and activated using phosphoric acid in removing methylene blue dye was investigated. Three types of palm-based wastes (seeds, leaflet and inedible crystallized date palm molasses) were used and converted to CMs via HTC process. The prepared samples were then activated using phosphoric acid via incipient wetness impregnation method. The CMs samples before and after activation were analyzed using scanning electron microscopy (SEM), elemental analysis and scanning (CHNS), Fourier Transform-Infrared (FTIR) and Brunauer–Emmet–Teller (BET) method. The samples exhibited high BET surface areas after activation (1,584 m2/g). The methylene blue adsorption results showed good fittings to the Langmuir and Redlich-Peterson isotherm models for all activated samples. The maximum adsorption capacity achieved was 409.84 mg/g for activated CM obtained from the palm date molasses, indicating high potential for application as dye-based adsorption materials.

The ultramafic-hosted Kairei vent field, located at 25°19′S, 70°02′E towards the northern end of the segment 1 of the Central Indian Ridge (CIR-S1) in a water depth of ~2450 m. This study aims to investigate the distribution of trace elements among sulfides of differing textures, and discuss the possible factors controlling the trace element distribution in those minerals by using LA-ICP-MS spot analyses as well as line scans. Our results show that there are distinct systematic trace element distributions throughout the different minerals：(1) Pyrite is divided into three types at the Kairei, including early-stage euhedral pyrites (py-I), sub-euhedral pyrites (py-II), and colloform pyrites (py-III). Pyrite is generally enriched in Mo, Au, As, Tl, Mn, and U. py-I have higher contents of Se, Te, Bi, and Ni, py-II are enriched in Au relative to py-I and py-III, but poor in Ni, py-III are enriched in Mo, Pb, and U but are poor in Se, Te, Bi, and Au. Variations in the concentrations of Se, Te, and Bi in pyrite are likely governed by the strong temperature gradient. Ni is generally lower than Co in pyrites, indicates that our samples precipitated at a high-temperature condition, whereas the extreme Co enrichment is likely from a magmatic heat source combined serpentinization reactions underlie the deposits. (2) Chalcopyrite is characterized by high concentrations of Co, Se, Te. The abundant of Se and Te in chalcopyrite cause by the high solubilities of Se and Te incorporated into chalcopyrite lattice at high temperature fluids. The concentration of Sb, As and Au is relatively low in chalcopyrite from the Kairei vent field. (3) Sphalerite from both the Zn-rich chimney is characterized by high concentrations of Sn, Co, Ga, Ge, Ag, Pb, Sb, As, and Cd, but depleted in Se, Te, Bi, Mo, Au, Ni, Tl, Mn, Ba, V, and U in comparison with the other minerals. The high concentration of Cd and Co is likely caused by the substitution of Cd2+ and Co2+ for Zn2+ in sphalerite. A high concentration of Pb accompanied by high Ag concentration in sphalerite indicating the Ag occurs in the microinclusions of Pb-bearing minerals such as galena. Au is generally low in sphalerite and strong correlate with Pb suggesting its presence in the microinclusions of galena. The strong correlation of As with Ge in sphalerite from Kairei suggests that they might precipitate under medium- to low-temperature with moderately reduced conditions. (4) Bornite-digenite is very low in most trace elements, except for Co, Se, and Bi. The high concentration of Se and Bi in all the sulfide minerals was observed in bornite-digenite can be explained by abundant Bi-selenide inclusions. Serpentinization in ultramafic-hosted hydrothermal systems might play an important role on Au enrichment in pyrite with low As contents. Compared with felsic-hosted seafloor massive sulfide (SMS) deposits, sulfide minerals from the ultramafic-hosted deposits show higher concentrations of Se and Te, but lower As, Sb, and Au concentrations attributed to the contribution of magmatic volatile input. Significant Se enrichment in chalcopyrite has been found from mafic-hosted SMSs indicate that the primary factor that controls the Se enrichment is its temperature-controlled mobility in fluids.

Owing to its properties, boron carbide has been applied in scientific and industrial fields. For this reason, B4C powders should be characterized by high purity and homogeneity in grain size and shape. In this study, boron carbide was prepared using precursors obtained by a hydrothermal method, and the grain morphology of the product was investigated. Boric acid and the saccharides glucose, fructose, inulin, and sorbitol were used as the precursors. Two precursor dehydration methods, freeze-drying and recrystallization, were compared. The precursors were subjected to DLS grain size and FT-IR spectrophotometric studies, and SEM observations of the precursors and products were performed, confirming that boron carbide powders with submicron spherical grains could be successfully synthesized.

The Shitouping pluton in Jiangxi Province, southern China, hosts an ion-adsorption heave rare earth element (HREE) deposit identified by recently geological survey. This study reveals the HREE pre-enrichment mechanism during the magma-hydrothermal process of granitic bedrock based on the comprehensive study of zircon structure and composition. Zircon from the Shitouping pluton, composed of syenogranite and monzogranite, can be categorized into three types based on structure and compositions. The Type-1 zircons, the predominate type in monzogranite granite, are early magmatic zircons with prismatic crystals and bright oscillatory zoning. In contrast, the late magmatic-hydrothermal zircons (Type-2 and Type-3) are mainly occurred in the syenogranite. The Type-2 zircons occur as murky euhedral crystals crystallized in the late magmatic stage. The Type-3 zircons with irregular zoning and abundant mineral inclu-sions in BSE images are closely associated with Type-2 zircons, possibly formed via intense hy-drothermal alteration during the hydrothermal stage. The increase in Y/Ho ratios from Type-1 to Type-3 zircon indicates that the Shitouping syenogranites underwent magmatic to hydrothermal evolution. Compared with Type-1 and Type-2 zircons, Type-3 zircons exhibit the highest con-centrations of F and HREEs. The significant increase of HREE concentrations both in zircons and bulk-rock composition of syenogranite can be attributed to the introduction of HREE-rich fluids during magma evolution. Under this condition, the HREEs mainly hosted in fluorocarbonates, which can easily release HREE3+ to generate ion-adsorption deposits during the weathering process. Therefore, we propose that increase of HREE contents in zircon reflect the exsolution of HREE-rich fluids during the magma evolution, which is important factor controlling HREE en-richment in Shitouping syenogranites and further generation of ion-adsorption HREE deposits.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

The subject of the research are materials formed as a result of hydrothermal treatment, in this case cellular concretes, both traditional and modified with plastics (HIPS). There are two types of materials resulting from hydrothermal treatment: autoclaved sand-lime bricks and autoclaved concrete. Both in the case of ABK and silicates, the basic stubstrates used during their production are: lime, sand and water (cement is also added to cellular concrete). The article presents the methodology of testing the porous structure of autoclaved materials with the use of computed tomography. Aerated concrete (light autoclaved concrete) has a compressive strength of 2-6 MPa. The tests included aerated concrete modified with high-impact polystyrene, commonly known as HIPS. HIPS high-impact polystyrene is a thermoplastic polymer that is obtained by block-suspension polymerization of styrene with the addition of synthetic rubber. As a result of polymerization, small particles of polybutadiene remain in the polystyrene male, changing its physical and mechanical properties. The results from the content of air voids in the autoclaved concrete sample with HIPS were on average: 52.53%.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

Relationship between caveman prehistoric life in terms of heat induced food processing and its geological ecosystems have received many attentions. Previous studies have investigated the sources of heat included using Fourier transform infrared spectroscopy and biomarker approaches. Here this study proposes the use of remote sensing to identify the relationship of 9500 year old (9.5 ka) prehistoric mongoloid occupancy with hydrothermal manifestations at Pawon cave of West Java. The hydrothermal manifestations around Pawon cave were identified using Landsat 8 band combinations, land surface temperature, and sedimentary lithology. The results showed the hydrothermal manifestations surrounding Pawon cave were within a distance of 0.5-2 km. The results also showed bones representing 12 animal taxon groups with high abundance of rodents. To conclude this study sheds the light of proximity and preferences of mongoloid prehistoric occupancy towards hydrothermal landscape due to its advantage as heat sources for food processing purposes.

In this work, the effect of reaction time and biomass-to-H2O ratio on the structural evolution of hydro-char and kinetic of by hydrothermal processing of corn Stover with hot compressed H2O, have been systematically investigated. The experiments were carried out at 250 °C, heating rate of 2.0 °C/min, biomass-to-H2O ratio of 1:10, and reaction times of 60, 120, and 240 minutes, and at 250 °C, 240 minutes, heating rate of 2.0 °C/min, and biomass-to-H2O water ratio of 1:10, 1:15, and 1:20, using a pilot scale stirred tank reactor of 5 gallon. The characterization of solid phase products performed by thermo-gravimetric analysis, scanning electron microscope, energy dispersive X-ray spectroscopy, X-ray diffraction, and elemental analysis (C, N, H, S). The physical-chemistry properties of solid phase analyzed in terms of dry matter (DM), total organic content (TOC), and ash. The yields of solid and gas phases decrease linearly with decreasing biomass-to-H2O ratio, while that of liquid phases increases linearly. For constant biomass-to-H2O ratio, the yields of solid, liquid, and gaseous reaction products varied between 52.97 and 35.82% (wt.), 44.84 and 54.59% (wt.), and 2.19 and 9.58% (wt.), respectively. The yield of solids decreases exponentially by decreasing the reaction time, while the yields of liquid and gas phases increase exponentially. For constant biomass-to-H2O ratio, TG/DTG curves shows that reaction time of 60 minutes was not enough to carbonize corn Stover. For constant reaction time, TG/DTG curves shows that increasing the H2O-to-biomass ratio worse the carbonization of corn Stover. For constant biomass-to-H2O ratio, the SEM images show the main morphological structure of the corn Stover remains practically unchanged, while for constant reaction time, SEM images show that plant microstructure retains part of its original morphology, demonstrating that a decrease on biomass-to-H2O ratio worse the carbonization of corn Stover. For constant biomass-to-H2O ratio, the EDX analysis shows that the carbon content in hydro-char increases with reaction time, while for constant reaction time, the carbon content decreases with increasing biomass-to-H2O ratio. The kinetic of corn Stover degradation was correlated with a pseudo-first order exponential model, exhibiting a root-mean-square error (r2) of 1.000, demonstrating that degradation kinetics of corn Stover with hot compressed H2O, expressed as hydro-char formation, is well described by an exponential decay kinetics.

Background: Early diagnosis of postoperative complications is an urgent task, allowing timely prescribing of appropriate therapy and reducing the cost of patient treatment. Prognostic models based on various data could help in the early diagnosis of postoperative complications after cardiac surgery. Objectives: The purpose of the study was to determine whether an integrated approach based on clinical data along with metabolites and biomarkers had greater predictive value than the models built on less data. Methods: The study included patients (n=62) admitted for planned cardiac surgery (coronary artery bypass grafting with cardiopulmonary bypass), who were retrospectively divided into two groups depending on the presence (n=26) or absence (n=36) of postoperative complications of all types. Clinical and laboratory data on the first day after surgery were analyzed. Additionally, patients' blood samples were collected before and on the first day after surgery to determine biomarkers (interleukin-6, procalcitonin, NT-proBNP, high-sensitivity troponin T) and metabolites (8 aromatic and 2 dicarboxylic acids were detected using gas chromatography-mass spectrometry). Results: Patients before surgery, compared with healthy donors, differed in the concentration of metabolites (p &lt; 0.05), and had concentrations of a number of biomarkers exceeding the corresponding reference values. Multivariate PLS-DA models, predicting the presence or absence of postoperative complications, were built using clinical data (ROC-AUC=0.71), concentrations of metabolites and biomarkers (ROC-AUC=0.60), and the entire data set (ROC-AUC=0.75). For comparison we built univariate models using the EuroScore2 (ROC-AUC=0.59) and SOFA (ROC-AUC=0.76) scales; concentrations of lactate (ROC-AUC=0.71), the dynamic changes of 4-hydroxyphenyllactic acid (ROC-AUC=0.69), and the sum of three sepsis-associated metabolites (ROC-AUC=0.70). The proposed complex model using entire data set was comparable to the SOFA scale, which confirms the expediency of searching for new predictive models based on a variety of factors.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

The aim of this retrospective study was to compare the clinical outcomes of treating isolated surgical neck fractures of the humerus using either the intramedullary nail or the MIROS (Minimally Invasive Reduction and Osteosynthesis System®) system. The study included 42 patients who underwent surgical treatment at the Polyclinic from January 2014 to June 2020. The results indicated that both treatments were effective; however, the MIROS system exhibited a higher complication rate. Intramedullary nailing was more reliable, thus recommended as the primary treatment method. This study underscores the importance of selecting the appropriate fixation technique to minimize complications and enhance patient outcomes.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Excess nitrogen in agricultural drainage poses a serious threat to the water quality safety of the Yellow River basin. Utilizing aquatic plants to modify the rhizosphere microbial community structure and facilitate nitrogen transformation is a crucial strategy for mitigating regional water eutrophication. Our results revealed that the denitrification rate (DR), dissimilatory nitrate reduction to ammonium rate (DNRAR) and nitrogen fixation rate (NFR) of rhizosphere sediments exhibited a significant increase in artificially cultivated ditch. Compared with those in natural ditches, the richness of the bacterial community and the relative abundances of Bacteroidota, Verrucomicrobiota, Firmicutes, Anaeromyxobacter and Geobacter, which are involved mainly in the nitrogen cycle, in the rhizosphere sediments of artificially cultivated ditch were significantly greater due to improvements in environmental conditions. In artificially cultivated ditch, the dominant functional genes affecting DRNARs in the rhizosphere sediments of P. australis were nrfC and nrfA, while DRs were driven mainly by norB and napA, which were influenced by the nitrogen and carbon levels; and the dominant functional genes affecting NFRs in the rhizosphere sediments of T. orientalis were nifD, nifK and nifH. Our results provide a scientific basis for the use of aquatic plants for mitigating excess nitrogen levels in agricultural drainage.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

In this paper, we extend the KdVSKR equations in (1+1)-dimension and (2+1)-dimension to fractional KdVSKR equations with modified Riemann-Liouville derivative. The (2+1)-dimensional KdVSKR equation, which is a recent extension of (1+1)-dimensional KdVSKR equation, can model the resonances of solitons in shallow water. By means of the Hirota bilinear method, finite symmetry group method and consistent Riccati expansion method, many new interaction solutions have been derived. Soliton-cnoidal interaction solution of the (1+1)-dimensional fractional KdVSKR equation has been derived for the first time. For the (2+1)-dimensional frac-tional KdVSKR equation, two-wave interaction solutions and three-wave interaction solutions, including dark-soliton-sine interaction solution, bright-soliton-elliptic interaction solution, and lump-hyperbolic-sine interaction solution, have been derived. Impact of the fractional order on the shapes of these solutions has been illustrated by figures. Three-wave interaction solutions of fractional systems have not been reported in the existing references. The research idea in this paper can be applied to other fractional differential equations.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Antimicrobial peptides represent a promising alternative to traditional drugs in relation to cost, toxicity and, primarily, the growing problem of drug resistance. Here we report on the activity against HSV-1 and HSV-2 of a previously described wide-spectrum synthetic decapeptide, Killer Peptide (KP). As determined by plaque reduction assays, treatment with KP at 100 μg/mL resulted in a reduction in the viral yield titer of 3.5 Logs for HSV-1 and 4.1 Logs for HSV-2. Further evaluation of KP antiviral activity focused on the early stages of virus replicative cycle, including the determination of the residual infectivity of viral suspensions treated with KP. A direct effect of the peptide on viral particles, impairing virus absorption and penetration, was shown. The toxicity profile proved to be extremely good with a selectivity index of 29.6 for HSV-1 and 156 for HSV-2. KP was also active against an acyclovir (ACV)-resistant HSV-1 strain, while HSV-1 subcultures in the presence of sub-inhibitory doses of KP did not lead to the emergence of resistant strains. Finally, the antiviral action of KP proved to be synergistic with that of ACV. Overall, these results demonstrate that KP could represent an interesting addition/alternative to acyclovir for antiviral treatment.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.