Aiming at the problem of hypersonic morphing vehicle avoiding no-fly zones and reaching the target, an improved predictor-corrector guidance method is proposed. Firstly, the aircraft motion model and the constraint model are established. Then, the basic algorithm is given, the Q-learning method is used to design the attack angle and sweep angle scheme to ensure that the aircraft can fly over the low-altitude zones. The B-spline curve is used to design the location of flight path points and the bank angle scheme is designed according to the predictor-corrector method, so that the aircraft can fly around to avoid high-altitude zones. Next, Monte Carlo reinforcement learning(MCRL) method is used to improve predictor-corrector method and Deep Neural Network(DNN) is used to fit reward function. The improved method can generate trajectory with better performance. Simulation results verify the effectiveness of the proposed algorithm.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

This paper focuses on the integrated guidance and autopilot design with control input saturation in the end-game phase of hypersonic flight. Firstly, uncertain nonlinear integrated guidance and autopilot model is developed with third actuator dynamics, where the control surface deflection has magnitude constraint. Secondly, neural network is implemented in extended state observer (ESO) design, which is used to estimate the complex model uncertainty, nonlinearity and state coupling. Thirdly, a command filtered back-stepping controller is designed with hybrid sliding surfaces to improve the terminal performance. In the process, different command filters are implemented to avoid the influences of disturbances and repetitive derivation, meanwhile solve the problem of unknown control direction caused by saturation. The stability of closed-loop system is proved by Lyapunov theory, and the principles abided by the controller parameters are concluded through the proof. Finally, series of 6-DOF numerical simulations are presented to show the feasibility and validity of the proposed controller.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

The use of privileged scaffolds as starting point for the construction of libraries of bioactive compounds is a widely used strategy in drug discovery and development. Scaffold decoration, morphing and hopping are additional techniques that allow to modify the privileged framework chosen and better explore the chemical space around it. In this study, two series of highly functionalized pyrimidine and pyridine derivatives were synthesized by scaffold morphing approach of triazine compounds obtained previously as antiviral agents. Newly synthesized azines were evaluated against lymphoma, hepatocarcinoma, and colon epithelial carcinoma cells showing in five cases acceptable to good anticancer activity associated to low cytotoxicity on healthy fibroblasts. Finally, ADME in vitro studies were conducted on the best derivatives of the two series showing good passive permeability and resistance to metabolic degradation.

In a previous paper, the authors dealt with the current showstoppers for morphing systems and with the reasons that have inhibited their commercial applicability. In this work, the authors ex-press a critical vision of the current status of the proposed architectures and the needs that should be accomplished to make them viable for installation onboard of commercial aircraft. The distinc-tion is essential because military and civil issues and necessities are very different, and both the solutions and difficulties to be overcome are widely diverse. Yet, still remaining in the civil seg-ment, there can be other differences, depending on the size of the aircraft, from large jets to com-muters or general aviation, in turn classifiable in tourism, acrobatic, ultralight and so on, each with their own peculiarities. Therefore, the paper wants to try to trace a common technology de-nominator, if possible, and envisage a future perspective of actual applications.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

This work proposes a systematic topology optimization approach to simultaneously design the morphing functionality and actuation in three-dimensional wing structures. The actuation is assumed to be a linear strain-based expansion in the actuation material and a three-phase material model is employed to represent structural and actuating materials, and void. To ensure both structural stiffness with respect to aerodynamic loading and morphing capabilities, the optimization problem is formulated to minimize structural compliance while morphing functionality is enforced by constraining a morphing error between actual and target wing shape. Moreover, a feature mapping approach is utilized to constrain and simplify actuator geometries. A trailing edge wing section is designed to validate the proposed optimization approach. Numerical results demonstrate that three-dimensional optimized wing sections utilize a more advanced structural layout to enhance structural performance while keeping morphing functionality than two-dimensional wing ribs. The work presents the first step towards systematic design of three-dimensional morphing wing sections.

Sailing sports are experiencing a period of radical innovations. Traditional displacing monohulls have always been the reference for yachting in the past, but the continuous quest for performances has generated many variations and many convergences with surprising results. On the aerodynamic side conventional soft sails have been sometime replaced by rigid wings, but the biggest innovation has been the use of traction kites as a propulsion device. On the hydrodynamic side we have seen the rapid growth of hydrofoils, an old concept that is having a rebirth. Probably the most remarkable expression of innovation and integration between concepts having different roots is the hydrofoil kite-board, point of encounter of the traditional wave surfing, the traction kite innovation and the hydrofoil technology. Hydrofoil kite-board can reach speeds up to 3 times the wind speed, are at least one order of magnitude cheaper than any boat with comparable performances, easy to manage and races are spectacular. Hydrofoil are object of investigation trying to further improve performances as well as to increase the stability and the “sailability". In the following we will present a concept that extends the range of efficiency of the foil through a completely passive morphing of the wing.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

This work communicates the connection of measured shadowgraphs from optically induced air breakdown with emission spectroscopy in selected gas mixtures. Laser-induced optical breakdown is generated using 850 mJ and 170 mJ, 6-ns pulses at a wavelength of 1064 nm, the shadowgraphs are recorded using time-delayed 5-ns pulses at a wavelength of 532 nm and a digital camera, and emission spectra are recorded for typically a dozen of discrete time-delays from optical breakdown by employing an intensified charge-coupled device. The symmetry of the breakdown event can be viewed as close-to spherical symmetry for time-delays of several 100 ns. Spectroscopic analysis explores well-above hypersonic expansion dynamics using primarily the diatomic molecule cyanide and atomic hydrogen emission spectroscopy. Analysis of the air breakdown and selected gas breakdown events permits the use of Abel inversion for inference of the expanding species distribution. Typically, species are prevalent at higher density near the hypersonically expanding shockwave, measured by tracing cyanide and a specific carbon atomic line. Overall, recorded air breakdown shadowgraphs are indicative of laser-plasma expansion in selected gas mixtures, and optical spectroscopy delivers analytical insight into plasma expansion phenomena.

This study uses a wind turbine case study to showcase an architecture for implementing a distributed digital twin in which all important aspects of a predictive maintenance solution in a DT use a fog computing paradigm, and the typical predictive maintenance DT is improved to offer better asset utilization and management through real time condition monitoring, predictive analytics, and health management of selected components of Wind turbines in a wind farm.. Digital twin (DT) is a technology that sits at the intersection of Internet of Things, Cloud Computing and Software Engineering to provide a suitable tool for replicating physical objects in the digital space. This can facilitate the implementation of asset management in manufacturing systems through predictive maintenance solutions leveraged by Machine Learning (ML). With DTs, a solution architecture can easily use data and software to implement asset management solutions such as Condition Monitoring and Predictive Maintenance using acquired sensor data from physical objects and computing capabilities in the digital space. While DT offers a good solution, it is an emerging technology that could be improved with better standards, architectural framework, and implementation methodologies. Researchers in both academia and industry have showcased DT implementations with different levels of success. However, DTs remain limited in standards and architectures that offer efficient predictive maintenance solutions with real time sensor data, and intelligent DT capabilities. An appropriate feedback mechanism is also needed to improve asset management operations.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

The concept of smart morphing blades, which can control themselves to reduce or eliminate the need for active control systems, is a highly attractive solution in blade technology. In this paper an innovative passive control system based on Shape Memory Alloys (SMAs) is proposed. On the basis of previous thermal and shape characterization of a single morphing blade for a heavy-duty automotive cooling axial fan, this study deals with the numerical analysis of the aerodynamic loads acting on the fan. By coupling CFD and FEM approaches it is possible to analyze the actual blade shape resulting from both the aerodynamic and centrifugal loads. The numerical results indicate that the polymeric blade structure ensures proper resistance and enables shape variation due to the action of the SMA strips.

This study focuses on the aerodynamic optimization of the re-entry capsule (REC) Orion Crew Exploration Vehicle (CEV) module, evaluating its performance using computational fluid dynamics (CFD). Three different models, namely Baseline, 2-Duct, and 4-Duct, are investigated under a wide range of flow speeds, from supersonic (Ma=1.6) to hypersonic (Ma=6) regimes. Thermofluids aspects, drag coefficient, surface heat flux, and the effectiveness of the modified geometry are assessed using aerodynamic and temperature-based models. The results show that the introduction of ducts in the 2-Duct and 4-Duct models leads to an average decrease in the drag coefficient of approximately 2.1% and 2.9%, respectively, compared to the baseline model, across all Mach numbers. The maximum reduction in drag coefficient is 3.55%, observed at Ma=1.4 using the 4-Duct capsule. However, it is found that the addition of extra ducts to the model increases the maximum heat transfer rate. Specifically, the heat flux is increased by up to 69% for the 4-Duct model at Ma=6, compared to the baseline model. On average, the heat flux is increased by approximately 28.6% for all conditions. The findings indicate that the introduction of ducts in the REC model improves its aerothermodynamic performance by reducing drag but also increases the heat transfer rate on the surface.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (<5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

The primary objective of this experiment is to enhance road safety and mitigate the occurrence of accidents by leveraging Low Power Wide Area Networks (LPWAN), specifically focusing on the Long Range (LoRa) network. Through comprehensive research into LPWANs and their various applications, we have designed and implemented a novel approach employing two mobile robots. These robots are utilized to emulate a typical traffic scenario, with one robot leading the way, skillfully maneuvering around obstacles, while the other robot closely follows behind, tracing the same path. The leading robot is tasked with collecting data from its internal environment, the external surroundings, and its operator through an array of sensors. Subsequently, this data is transmitted to the trailing robot. The follower robot's role is to analyze the data received and formulate decisions based on this information. Its objective is to mimic safe driving behavior, particularly when the received data deviates from the expected norms. In such instances, the follower robot will opt to decelerate significantly, thereby minimizing the risk of collision. By implementing this innovative system, we aim to significantly enhance driving safety and reduce the occurrence of accidents on the road.

Steady-state one-dimensional flows of five-component air behind a normal shock wave are considered with one-temperature model. A mathematical model is formulated to describe the relaxation of a five-component air mixture with a one-temperature non-equilibrium approximation. A numerical study of non-equilibrium flows of a reacting five-component air mixture behind shock waves at different heights and velocities of free flow is performed. The contribution of different types of reactions to the overall relaxation of the mixture is discussed, and the distributions of macro-parameters of the flow behind the shock wave front are calculated. The lengths of the relaxation zones behind the shock wave front are compared at different initial conditions.

The process involved in preparing driving simulator tests is a labor intensive one, and the nature of this complexity depends on the sophistication of the tests to be carried out, as well as the number of participants. Which has an impact on the duration of the research itself. The very solution of using driving simulators is a research tool that has been in use for many years and with great success. They are used in a very wide range of areas of human functioning. They replicate in a very realistic way the conditions that can occur in the external environment, offer the possibility of repetition of particular conditions and insight into certain behaviors that could be very difficult to initiate in real life. This article also describes the dis- ease of using simulators to conduct research activities, along with the workflow from assumptions to finalizing the research. An algorithm is also presented for the study of individual participants, with examples for separate research scenarios concerning driver behavior in the vicinity of pedestrian crossings.

This study explores the intricate relationship between the angle of vehicle-to-vehicle (V2V) conflicts and the severity of conflicts at signalized intersections during traffic signal failures, leveraging the advanced capabilities of LiDAR sensor technology. The research delves into the impact of conflict angles on collision outcomes and introduces LiDAR as a novel and precise tool for capturing spatial dynamics during unregulated traffic movements. Findings reveal that as the angle of V2V conflicts increases, indicating a wider approach between vehicles, the severity of conflicts tends to decrease. This reduction in severity is attributed to the detailed spatial data provided by LiDAR, enabling the identification of glancing impacts rather than direct head-on collisions. The mitigation of forces involved in collisions at increased angles contributes to a decreased likelihood of severe consequences, such as extensive vehicle damage and serious injuries to occupants.Conversely, as the angle of V2V conflicts decreases, signifying a narrower approach between vehicles, the potential for severe collisions tends to increase. LiDAR technology facilitates precise measurements of spatial coordinates and temporal dynamics, revealing that collisions occurring at smaller angles involve more direct and concentrated impact forces. This heightened risk of extensive damage to vehicles and increased injury severity is crucially captured by LiDAR, providing valuable insights into the relationship between conflict angles and collision outcomes during traffic signal failures. This study underscores the efficacy of LiDAR sensor technology in understanding the nuanced dynamics of V2V conflicts and highlights its role in developing targeted safety interventions. The integration of LiDAR data into traffic safety analyses offers a sophisticated approach to mitigating the impact of conflicts and enhancing overall safety at signalized intersections during signal failures. The research also highlighted that as the angle of V2P conflicts widens, PET experiences a proportional increase. A larger conflict angle signifies a more complex interaction between vehicles and pedestrians, leading to prolonged PET values. Conversely, a decrease in the angle of V2P conflicts is associated with a reduction in PET during traffic signal failures.The study commences with an examination of traffic characteristics at the E Cold Spring Ln – Hillen Rd intersection in Baltimore City, MD, utilizing a deployed LiDAR sensor. When the signal at this intersection experienced a temporary malfunction on a regular working day in September 2023, the LiDAR captured data related to vehicle and pedestrian volumes, as well as V2V and V2P conflicts. The primary objective of the research is to evaluate the repercussions of traffic signal failures on both traffic flow and safety, specifically V2V and V2P conflicts, occurring during periods of improper signal functionality. Additionally, this investigation delves into various factors that impact traffic signal performance, encompassing traffic demand, geometric layout, pedestrian interactions, and the incorporation of emerging technologies.

An integrated approach to active flow control is proposed by finding both the drooping leading edge and the morphing trailing edge for flow management. This strategy aims to manage flow separation control by utilizing the synergistic effects of both control mechanisms, which we call the Combined Morphing Leading Edge and Trailing Edge (CoMpLETE) technique. This design is inspired by a bionic porpoise nose and the flap movements of the cetacean species. The motion of this mechanism achieves a continuous, wave-like, variable airfoil camber. The dynamic motion of the airfoil's upper and lower surface coordinates in response to unsteady conditions is achieved by combining the thickness-to-chord (t/c) distribution with the time-dependent camber line equation. A parameterization model was constructed to mimic the motion around the morphing airfoil at various deflection amplitudes at stall angle of attack and morphing actuation start times. The mean properties and qualitative trends of the flow phenomena are captured by the transition-SST (Shear Stress Transport) model. The effectiveness of the dynamically morphing airfoil as a flow control approach is evaluated by obtaining the flow field data, such as velocity streamlines, vorticity contours, and aerodynamic forces. Different cases are investigated for the CoMpLETE morphing airfoil, which evaluates the airfoil’s parameters, such as its morphing location, deflection amplitude, and morphing starting time. The morphing airfoil’s performance is analyzed to provide further insights into the dynamic lift and drag force variations at pre-defined deflection frequencies of 0.5 Hz, 1 Hz, and 2 Hz. The findings demonstrate that adjusting the airfoil camber reduces streamwise adverse pressure gradients, thus preventing significant flow separation. Although the trailing edge deflection and its location along the chord influence the generation and separation of the Leading-Edge Vortex (LEV), these results show that the combined effect of the morphing leading edge and trailing edge has the potential to mitigate flow separation. The morphing airfoil successfully contributes to the flow reattachment and significantly increases the maximum lift coefficient (c_(l,max))). This work also broadens its focus to investigate the aerodynamic effects of a dynamically morphing leading and trailing edge, which seamlessly transitions along the side edges. The aerodynamic performance analysis is investigated across varying morphing frequencies, amplitudes, and actuation times.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Transition delaying is of great importance for the drag and heat flux reduction of hypersonic flight vehicles. The first mode within low frequency and the second mode within high frequency exist simultaneously during the transition of hypersonic boundary layer. This paper proposes a novel bi-frequency synthetic jet to suppress low- and high-frequency disturbances at the same time. Orthogonal table and variance analysis are used to compare the control effects of jet with different frequencies, amplitudes and positions. Linear stability analysis results show that, low frequency synthetic jet can suppress the first mode when it is arranged upstream of synchronization point, while the second mode control effect is relatively weak. The higher the high frequency is, the stronger the suppression effect is on the first mode. For the second mode, the suppression effect is only at f2=89.09kHz. The larger the amplitude, the weaker the promoting effect for the first mode and the second mode, and the more obvious the suppressing effect. For the cases with synthetic jet downstream of synchronization point, all levels of the three parameters promote the unstable mode. In terms of the growth rate with the spanwise wave number, the control effect of the same factor and level under different spanwise wave number is different. In order to obtain the optimal control effect on transition, the three factors and the arrangement position of the synthetic jet should be selected as follows: the position is arranged in the upstream, with f1 = 17.82kHz, f2 = 89.9kHz, a =0.007, so that the maximum growth rate of the first mode is reduced by 9.06% and that of the second mode is reduced by 1.28% compared with the uncontrolled state.

Vehicle-to-Vehicle (V2V) communication plays a pivotal role in modern intelligent transportation systems, enabling seamless information exchange among vehicles to enhance road safety, traffic efficiency, and overall driving experience. However, the secure transmission of sensitive data between vehicles remains a critical concern due to potential security threats and vulnerabilities. This research paper focuses on investigating the security protocols employed in Vehicle-to-Vehicle communication systems. A comprehensive review and analysis of relevant literature and research papers is conducted to gather information on existing V2V communication security protocols and techniques. The analysis encompasses key areas, including authentication mechanisms, encryption algorithms, key management protocols, and intrusion detection systems specifically applicable to V2V communication networks. Within the context of real-world V2V environments, this study delves into the challenges and limitations associated with implementing these protocols. Moreover, to foster a deeper understanding, the paper investigates present communication protocols in the field of Internet of Things (IoT) that are tailored for V2V. Various parameters, such as band-width consumption, energy consumption, latency, and message size, are considered during the evaluation of these protocols to gauge their effectiveness. The research outcomes aim to provide a comprehensive understanding of the strengths and weaknesses of the current V2V communication security protocols. Furthermore, based on the findings, this paper will propose improvements and recommendations to enhance the security measures of the V2V communication protocol. Ultimately, this research will contribute to the development of more secure and reliable V2V communication systems, propelling the advancement of intelligent transportation technology.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The evolution in the post shock nonequilibrium relaxation in a hypersonic plasma flow was investigated during a shock’s reflection off a thermal discontinuity. Within a transitional period, the relaxation zone parameters past both, the reflected and transmitted waves, evolve differently compared to that in the incident wave. In a numerical example for the non-dissociating N₂ gas heated to 5000 K/10,000 K across the interface and M = 3.5, the relaxation time for the transmitted wave is up to 50% shorter and the relaxation depth for both waves is significantly reduced, thus resulting in a weakened wave structure. The results of extension into larger values of heating strength and the shock Mach numbers are discussed. The findings can be useful in the areas of research involving strong shocks interacting with optical discharges or other heated media on the scale where the shock structure becomes important.

Electric vehicles (EVs) play a significant role in reducing carbon emissions. In the US, EVs are mostly owned by multi-vehicle households, and their usage is primarily studied in the context of vehicle miles traveled. This study takes a unique approach by analyzing EV usage through the lens of vehicle choice (between EVs and internal combustion engine vehicles) within multi-vehicle households. A two-step machine-learning framework (clustering and decision trees) is proposed. The framework determines the preferred trip category for EV use and captures the effects of household attributes, driver attributes, built-environment factors, and gas prices on EV use in multi-vehicle households. Results indicate that discretionary trips (accumulated local effect = 0.037) are mostly preferred for EV use. EV preference is more pronounced among households with fewer workers (<2) and lower income levels. These findings are valuable for policymakers and auto manufacturers in targeting specific market segments and promoting EV adoption.

In this paper, we present a novel Two-Echelon Ground Vehicle and Its Mounted Unmanned Aerial Vehicle Cooperated Routing Problem (2E-GUCRP). The 2E-GUCRP arises in the field of Unmanned Aerial Vehicle (UAV) Routing Problem such as those encountered in the context of city logistics. In a typical cooperated system, the UAV is launched from the Ground Vehicle (GV) and automatically flies to the designated target. Meanwhile, acting as a mobile base station, the GV can charge or change the UAV’s battery on the designated landing points to enable the UAV to continue its mission. The objective is to design efficient GV and UAV routes to minimize the total mission time while meeting the operational constraints. A Mixed Integer Programming (MIP) model, which could be solved by commercial software, is constructed to describe this problem. In order to quickly solve the medium-scale problems, two existing heuristics to solve 2E-VRP are improved. The computational experiments are set up to compare our model with the 2E-VRP. The results indicate that the 2E-GUCRP obtains a better efficiency. Further discussion of the practical instance points out that the increase in efficiency is related to the speed relationship between the GV and the UAV.

The goal of this paper is to investigate the aerodynamic and aerothermodynamic behaviour of the Schiaparelli capsule after the deployment of the supersonic disk-gap-band (DGB) parachute during its re-entry phase into the Martian atmosphere. Large-Eddy Simulations of compressible flows have been performed over the capsule and the flexible DGB parachute to analyse the behaviour of the turbulent wake behind the capsule and its interaction with the parachute flow-field. The simulations are performed at an altitude of 10 km and a Mach number around 2, i.e., a regime in which large canopy-area oscillations are observed. These simulations have shown a strong interaction between the bow shock, the recompression and expansion waves, high pressure, density and temperature gradients, heat flux towards the airstream and the body implying turbulence generation, ingestion, and amplification through the shock waves. This nonlinear turbulence flowfield explains the non-axisymmetric behaviour around and behind the parachute that caused the uncontrolled capsule oscillation and the mission failure.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

Hybrid electric vehicles are certainly one of the key solutions for improving fuel efficiency and reducing emissions, especially in special vehicle application and with the use of CO2 neutral fuels. Determining the energy management strategy and finding the optimal solution with regard to the aforementioned goals re-mains the one of the main challenges in the design of HEV. This paper presents a new vehicle modeling method, with an emphasis on HEVs, which is based on the frequency analysis of emissions and consumption according to the current specific traction power of the vehicle. The evaluation of the newly introduced model in the RDE, NEDC and WLTP cycle was performed and the results were compared with the standard verified vehicle model that was created in AVL's CruiseM software package. Positive traction energies have positive deviations of between 0.35% and 2.85%. The largest deviation in CO2 emissions was recorded for the HEV model in the RDE cycle and in the non-hybrid model in the WLTP cycle of 3.79% and 4.4% respectively, all other combinations of cycle and vehicles had deviations of up to about 1%. As expected, the largest relative deviations were recorded for NOx emissions from 0.13% to 9.62% for HEV in the WLTP cycle.

Peak-to-Average Power Ratio (PAPR) is one of the main problems in wireless communications using Orthogonal Frequency Division Multiplexing (OFDM). Its behavior is random and can produce problems for the hardware implementation, directly influencing the Packet Error Rate (PER). In this article, the PER is obtained for channels with Rayleigh and Rician fading. In the simulation, a High Power Amplifier (HPA) is added to the transmitter and for PAPR reduction Simple Amplitude Predistortion-Orthogonal Pilot Sequences (OPS-SAP) technique is used.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Accurate estimation of vehicle emissions is essential and can be helpful in the decision-making process. Thanks to calculation methods, it is possible to accurately estimate the emissions that result from driving a car and to determine their impact on, for example, the health of pedestrians who are on the pavement near an arterial road. Recent years have seen an increase in the use and importance of emission models, as well as vehicle traffic simulation models. Increasingly, emission models are being combined with traffic simulation models, as it is not practical to actually measure the on-road emissions of an entire fleet of vehicles over a given stretch of road. This paper provides an overview of the selected work on the topic of emission modelling and vehicle traffic simulation models. The models are distinguished according to their respective scales of accuracy, i.e., micro, meso, and macro. Selected work combining emission and traffic simulation models is also presented, as well as development trends in the field. In particular, the paper also highlights the fact of proper calibration of vehicle traffic simulation models in order to obtain the most reliable vehicle emissions results from computational models. The review of the works carried out may be helpful for future projects concerning the use of simulation tools for transport and environmental decision-makers in the area of arterial roads.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

Teaching kinematic rotations is a daunting task for even some of the most advanced mathematical minds. However, envisioning and explaining the three-dimensional rotations can be highly simplified by changing the paradigm. This paradigm change allows for a high school student with a understanding of geometry to be able to not only develop the matrix but also explain the rotations at a collegiate level. The proposed method includes the assumption of a point (P) within the initial three-dimensional frame with axes (x ̂_i, y ̂_i, z ̂_i). It then utilizes a two-dimensional rotation view (2DRV) to measure how the coordinates of point P translate after the initial axis is rotated instead of using the established Euler's formula. The equations are used in matrix notation to develop a direction cosine matrix (DCM) for future equations. This method provides a high school student with an elementary and repeatable process to compose and explain kinematic rotations.

The current study investigated the use of two-dimensional spatial distribution mapping representing the chlorophyll-a level in a river generated via an unmanned aerial vehicle (UAV) and an unmanned surface vehicle (USV). A domestically developed UAV (Remo-M, Uconsystem Inc., Korea) and a USV developed by our research team were used to collect data from the Nae Seong stream in Korea. An adaptation of the “Data Cleaner” tool was developed and used for USV data processing and analysis. The operation of the autonomous USV was successful. Four previously described indices for quantifying algal blooms in rivers were utilized to create chlorophyll-a images, the normalized difference vegetation index (NDVI), the normalized green red difference index, the green normalized difference vegetation index (GNDVI), and the normalized difference red edge index. The suitability of the linear regression analysis of the correlation between the spectral indices obtained using the UAV and the in situ chlorophyll-a data obtained using the USV was evaluated with the coefficient of determination (R2) at a significance level of p &lt; 0.001. In field application and correlational analysis the NDVI was strongly correlated with chlorophyll-a (R2 = 0.88, p < 0.001), and the GNDVI was moderately correlated with chlorophyll-a (R2 = 0.74, p < 0.001). The map of chlorophyll-a was successfully quantified using the UAV and USV hybrid platforms.

This paper examines the diurnal cycle of convection (DCC) over Lake Titicaca Basin (LTb) during summertime months based on the high spatial resolution (8 x 8 km2) and hourly temporal resolution, estimates of Climate Prediction Center Morphing technique (CMORPH). Analysis was performed using observed data from rain gauges (Rg-SENAMHI) for the period 2002 to 2013. Graphical comparisons and several statistical metrics such as correlation coefficient, bias, and root mean square error were used to evaluate CMORPH product. Spatial maps and graphic metrics of diurnal cycle were developed to assess CMORPH data, spatial dependency an accuracy over the LTb. Approximately, 43% of the total Rg-SENAMHI variation is explained CMORPH data. The correlation between Rg-SENAMHI and CMORPH is positively over southeast and northern LTb, and negatively in the central and southern LTb. A underestimation bias is observed over most the LTb areas and overestimation bias (e.g., Lagunillas, Isla Suana and Desaguadero stations). In general, spatial patterns of rainfall over the LTb were captured through CMORPH data. Over the surrounding lake area, high mountain, and plateau area, maximum peaks of precipitation occur in the early evening, neverhtheless over low areas such as the lake, surrounding and valleys, maximum precipitation values occur early morning. The results show that DCC its very related by surface exchange processes and local circulation resulting from solar radiation and heterogeneous topography.

This study presents a dynamic model of a passenger vehicle and analyzes its dynamic characteristics and responses. A dynamic vehicle model with seven degrees of freedom was established to analyze the behavior of a driving vehicle. The vehicle model had three degrees of freedom for the motion of the sprung mass and four degrees of freedom for the unsprung masses. For this model, the equations of motion were derived using Lagrange’s equation. To verify the model, the suspension deformations computed using the model were compared with the deformations measured through three actual vehicle driving tests which are the slalom, double lane change, and step steer tests. Furthermore, we investigated the effects of suspension stiffness, suspension damping, and anti-roll bar torsional stiffness on the dynamic characteristics and responses of the vehicle model. The developed dynamic vehicle model may help vehicle designers predict the dynamic responses of a vehicle through simulation without performing a driving test.

In past few years, unmanned aerial vehicles (UAV) or drones has been a hot topic encompassing technology, security issues, rules and regulations globally due to its remarkable advancements and uses in remote sensing and photogrammetry applications. This review paper highlights the evolution and development of UAV, classification and comparison of UAVs along with Hardware and software design challenges with diverse capabilities in civil and military applications. Further, safety and security issues with drones, existing regulations and guidelines to fly the drone, limitations and possible solutions have also been discussed.

The need for continuous research to refine the models used in accident reconstruction appears with the development of new car models that satisfy consumer complaints. The paper analyzed a sub-sequence of car and pedestrian accidents, from the perspective of the distance traveled by them in the contact phase, with the aim of improving the information regarding the reconstruction of road accidents. The research included the analysis of some accidents with pedestrian dummies, as well as the simulation of the impact between different classes of vehicles and pedestrians in two different walking positions. Specialized software was used with complex multibody models of pedestrians, modifying the speed and deceleration parameters at the time of the collision. The research results highlight the differences between bilinear models used in accident reconstruction and the proposed study. They can also be used to determine the distance traveled by the vehicle in the first phase of the collision with pedestrians.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

An emissions baseline for a city is the foundation to building an informed clean air action plan. This includes an understanding of the sources and their intensities to device cost-effective measures with the least health impacts. In an urban environment, emissions from road transport is one of the major contributors to the air pollution problem, and accounting for this sector requires a detailed profile of in-use vehicles, covering their age-mix, usage, and fuel economy. In this paper, we present a simplified framework to survey at select fuel stations to establish the necessary inputs and use them to build a localized vehicle emissions inventory. The methodology is illustrated with an application in the city of Patna, India. Here, the FuSS was employed to profile the in-use passenger vehicle characteristics by 19 trained students, over nine days and at ten fuel stations, to collect 9,775 survey points. The methodology outlined in this paper, along with the tools and training framework, is also replicable in settings other than the fuel stations.

The automobile industry is undergoing technological advancement, which includes breakthroughs such as hybrid cars, electric vehicles (EVs), and self-driving capabilities. However, despite these advances, issues remain, notably in recall management efficiency, security and risk of fraud. To solve these difficulties, the idea of Industry 4.0 has been adopted, which uses technologies such as sensors, IOT’s, and machine learning. Even this technology still has loopholes in the area of security which has been exploited negatively over time. In other to mitigate these loopholes we introduce Blockchain technology as a viable alternative, providing a safe and transparent environment. This study investigates and proposed the use of blockchain to create an enhanced Vehicle Tracking System (VTS) intended at enhancing recall management and reducing fraud in the automobile sector. The proposed solution was discussed in detail and a mock smart contract was also written, which was deployed on the Ethereum Virtual Machine (EVM).

Recently, the use of drones/unmanned aerial vehicles (UAVs) has notably increased due to their broad commercial spread and low cost. The wide diffusion of drones increases the hazards of their misuse in illegitimate actions such as drug smuggling and terrorism. Thus, the surveillance and automated detection of drones are crucial for safeguarding restricted regions or special zones from illegal drone interventions. One of the most challenging issues in drone detection in surveillance videos is the apparent similarity of drones and birds against complex backgrounds. In this work, an automated image-based drone-detection system utilizing an advanced deep-learning-based object-detection method known as you only look once (YOLOv5) is introduced for protecting restricted regions or special zones from unlawful drone interventions. Due to the lack of sufficient data, transfer learning was utilized to pretrain the object-detection method to increase the performance. The experiments showed outstanding results, and an average precision of 94.7% was accomplished.

Background: Previous investigations have found a correlation between abnormal curvatures and a variety of patient complaints such as cervical pain and disability. However, no study has shown that loss of the cervical curve is a direct result of exposure to a motor vehicle collision (MVC). This investigation presents a retrospective consecutive case series of patients with both a pre-injury cervical lateral radiograph (CLR) and a post-injury CLR after exposure to a MVC. Computer analysis of digitized vertebral body corners on CLRs was performed to investigate the possible alterations in the geometric alignment of the sagittal cervical curve. Methods: Three spine clinic records were reviewed, over a 2-year period, looking for patients where both an initial lateral cervical x-ray and an examination were performed prior to the patient being exposed to a MVC; afterwards an additional exam and radiographic analysis were required. A total of 41 patients met the inclusion criteria. Examination records of pain intensity on numerical pain rating scores (NPRS) and neck disability index (NDI), if available, were analyzed. The CLRs were digitized and modeled in the sagittal plane using curve fitting and the least squares error approach. Radiographic variables included total cervical curve (ARA C2-C7), Chamberlain’s line to horizontal (skull flexion), horizontal translation of C2 relative to C7, segmental translations (retrolisthesis and anterolisthesis), and circular modelling radii. Results: There were 15 males and 26 females with an age range of 8-65 years. Most participants were drivers (28) involved in rear end impacts (30). The pre-injury NPRS was 2.7 while the post injury was 5.0; p &lt; 0.001. The NDI was available on 24 /41 (58.5%) patients and was found to increase following exposure to the MVC: 15.7% to 32.8%, p &lt; 0.001. An altered cervical curvature was identified following exposure to MVC, characterized by an increase in radius of curvature and an approximate 8° reduction of lordosis from C2-C7; p &lt; 0.001. The mid cervical spine (C3-C5) showed the greatest curve reduction with localized mild kyphosis at these levels on average. Several participants developed segmental translations that approached the instability value of translation &gt; 3.5mm. Conclusions: Abnormalities of cervical lordosis occurred following exposure to a MVC. The average loss of cervical curvature was 8° from C2-C7, with mild flexion of the mid cervical segments. Snap through type or dynamic buckling during the MVC may explain our findings. The primary contribution of this study to the motor vehicle collision literature is that altered cervical lordosis may result from MVC exposures and the consequences of an altered cervical alignment, in turn, may lead to future pain, disability and decreased health-related quality of life.

Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

The environmental safety of a car is currently one of the most important indicators of the vehicle competitiveness and quality in the consumer market. Currently, the assessment of the ecological properties of vehicles can be made based on various criteria. In the case of combustion-powered cars, the most attention is usually paid to the values characterizing their use, and in the environmental assessment, first of all to pollutant emissions and operational fuel consumption. The proposed article considers the possibility of using the life cycle assessment to analyze the ecological properties of a passenger car during its operation. A simplified LCA method of the vehicle was presented, which in strictly defined cases can be used for the analysis of environmental impacts and the assessment of the energy analysis related to its operation. For this purpose, a vehicle life cycle model was developed. Data on the operation of 33 passenger cars of different manufacturers with similar operational characteristics, coming from different production periods, were analyzed in detail. The obtained results were found to be highly sensitive to the assumptions made in the article.

The development of autonomous vehicles is becoming increasingly popular and gathering real world data is considered a valuable task. Many datasets have been published recently in the autonomous vehicle sector, with synthetic datasets gaining particular interest due to availability and cost. For a real implementation and correct evaluation of vehicles at higher levels of autonomy it is also necessary to consider human interaction, which is precisely something that lacks in existing datasets. In this article the UPCT dataset is presented, a public dataset containing high quality, multimodal data obtained using state of the art sensors and equipment installed onboard the UPCT’s CICar autonomous vehicle. The dataset includes data from a variety of perception sensors including 3D LiDAR, cameras, IMU, GPS, encoders, as well as driver biometric data and driver behaviour questionnaires. In addition to the dataset, the software developed for data synchronisation and processing has been made available. The quality of the dataset was validated using an end-to-end neural network model with multiple inputs to obtain speed and steering wheel angle and obtained very promising results.

When a railway vehicle moves on a curved rail, sliding contact occurs between the rail head side and wheel flange, which wears the wheel flange down. The thinned flange needs to be restored above the required minimum thickness for structural safety. In this study, a new process and welding wire for restoring worn-out railway wheels by submerged arc welding was developed. To characterize the properties of the restored wheel, dilatometric analysis of phase transformation, SEM/EDX analyses, hardness measurement, and residual stress measurement using the X-ray diffraction method were performed. Finally, wear tests with full-size wheel/rail specimens were carried out. It was confirmed that the weld metal was composed of bainitic microstructures as intended, and welding defects were not observed. The wear amount of the restored wheel was greater than that of the base material, but it was less than half of the wear depth of the weld-repaired wheel with ferritic–pearlitic microstructures. The developed process seems applicable to industry.

Over the last few decades, ocean research and exploration have made underwater mechanical systems a necessity. Underwater vehicles provide a new kind of marine platforms that could represent a great necessity in many areas of oceanographic research. Until now, the underwater vehicles come in a verity of shapes, sizes and means of propulsion. Depending on these characteristics, the type and mission of the vehicle are also determined. The underwater robots are used for different inspection and intervention missions in e.g. the oil and gas industry, ocean science research. Due to multiple applications to which the vehicle can participate, it can be successfully used and to determine methods of re-use of marine energy. Environmental mapping provides accurate information about the main areas of interest of the energy, as well as the exploitation possibilities of that. Most of the time, biomimetic robots were inspired their senso structure, from different kind of animals, such as insects, fish and birds. Nowadays, the concept of a underwater robotic vehicles capable to move independently, autonomously or remotely, has a great potential and a large application. This is the reason that the last studies have been directed on biomimetic robots. The fish and other underwater animals have evolved superior swimming capabilities in many ways and represent a starting point to explain the fluid-mechanical principles. Furthermore, the underwater animals develop and achieve extraordinary propulsion efficiencies, acceleration and maneuverability. They can also achieve high speed under water. Implanting and creating a vehicle through a biomimetic approach reduces the energy used to maneuver the vehicle as it can automatically correct its position and displacement. The paper presents an examination of the state of biomimetic robotic fishes, underlining the reason why bio-inspiration can help us in the underwater locomotion technology.

With the development of sensor and communication technologies, Internet of Things (IoT) subsystem is gradually becoming a crucial part in vehicles. It can effectively enhance functionalities of vehicles. However, new attack types are also emerged. For example, a driver with the smart key in the pocket can push the start button to start a car when. At the same time, security issues in the push-to-start scenario are alerted, such as smart key forgery. In this paper, we propose a vehicle Passive Entry Passive Start (PEPS) system that uses deep learning algorithms to recognize the driver by the Electrocardiogram (ECG) signals measured by his or her smart watch. ECG signals are used for verification. Smart watches, as a new smart key of PEPS system, can replace traditional smart keys to improve security. Experiment results show that Long Short-Term Memory (LSTM) models have achieved the best accuracy score for identity recognition (91%) when single ECG cycle is used. However, it takes at least 30 minutes for training. The training time of Auto Encoder successfully reduces to 5 minutes. When 15 continuous ECG cycles are used, it can achieve 100% identity accuracy.

Carsharing has become increasingly popular in recent years as a sustainable transportation solution, offering individuals access to shared vehicles on a short-term basis. One-way carsharing, in particular, presents unique challenges due to its flexible nature, allowing users to pick up and drop off vehicles at different locations within a designated service area. This flexibility increases the service ridership but comes at the expense of vehicle imbalance among the stations, as some stations may have excess vehicles while other stations have vehicle shortages. Therefore, carsharing companies need to decide on strategies to ensure a balanced distribution of vehicles among the stations. This is essential as unbalanced vehicle distribution can lead to the unavailability of vehicles when needed or, conversely, result in an increased number of unnecessary rebalancing trips, thereby exacerbating traffic congestion and environmental pollution. Such issues can potentially undermine the overall contribution of carsharing to urban sustainability. To this end, this paper reviews the vehicle imbalance problem that arises in this field and the solution algorithms that solve them.

In the last decades, technological advances related to RNA manipulation enabled and expanded its application in vaccine development. This approach comprises synthetic single-stranded mRNA molecules that direct the translation of the antigen responsible for activating the desired immune response. The success of RNA vaccines depends on the delivery vehicle employed. Among the systems, yeasts emerge as a new approach to a natural delivery platform. The presence of β-glucans and mannans in its wall is responsible for the adjuvant action of this system. Yeasts are already employed to deliver protein antigens, with success and efficacy demonstrated through pre-clinical and clinical trials. Yeast β-glucan capsules, microparticles, and nanoparticles are capable of modulating host immune responses and have a high capacity to carry RNA and small molecules, with bioavailability upon oral immunization and with targeting to receptors present in anti-gen-presenting cells (APCs). Besides, yeasts are interesting vehicles for the protection and specific delivery of therapeutic vaccines based on shRNA or dsRNA. In this review, we present an overview of the attributes of yeast or its derivatives for the delivery of RNA-based vaccines, discussing their current challenges and prospects for using this promising strategy.

Fermented food products are widely consumed for their nutritional and health-promoting properties earning them a central place in diets around the globe. However, these foods can present a paradox, as they have the potential to harbor not only beneficial probiotics but also antibiotic-resistant (AR) microbes and genes. The impact of AR in fermented foods has far-reached implications, such as its potential effects on human health, repercussions in the food industry, and environmental consequences. An in-depth analysis of AR in fermented foods, including dairy products, fermented fruits and vegetables, meat products, and beverages, would provide insights into the extent and ramifications of the issue with these foods. Therefore, this review systematically presents the status of AR in fermented foods, with a particular focus on AR bacteria and genes within this category of food products. The review also highlights the complexities of AR in fermented foods, emphasizing the role of bacterial adaptation during the fermentation process and the dynamics of bacterial gene transfer. Various contributing factors to AR are brought into focus, including intrinsic resistance among bacteria in fermented foods and the potential risk of contamination with pathogenic bacteria. Moreover, this review presents a range of mitigation strategies, from the development of novel antimicrobials to advances in fermentation technology and regulatory control. This comprehensive perspective on the intricate interplay between AR and fermented food will potentially pave the way for more targeted research and mitigation strategies in this critical area.

According to the risk investigations of being involved in an accident, alcohol-impaired driving is one of the major causes of motor-vehicles accidents. Preventing highly intoxicated persons from driving would potentially save many lives. This paper proposes a lightweight in-vehicle alcohol detection that processes the data generated from 6-alcohol sensors (MQ-3 Alcohol Sensors) using an optimizable shallow neural network (O-SNN). The experimental evaluation results exhibit a high-performance detection system scoring a 99.8% of detection accuracy with a very short inferencing delay of 2.22 µ seconds. Hence, the proposed model can be efficiently deployed and used to discover in-vehicle alcohol with high accuracy and low inference overhead as a part of the driver alcohol detection system for safety (DADSS) system aiming at massive deployment of alcohol sensing systems that could potentially save thousands of lives annually.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

Connected and Autonomous Vehicle (CAV) combines technologies of autonomous vehicle (AV) and connected vehicles (CV) to develop quicker, more reliable and safer traffic. Artificial Intelligence (AI) based CAV solutions play significant roles in sustainable city. The convergence imposes stringent security requirements for CAV safety and reliability. In practice, vehicles are developed with increased automation and connectivity. Increased automation increases the reliance on the sensor-based technologies and decreases the reliance on driver; increased connectivity increases the exposures of vehicles vulnerability and increases the risk for an adversary to implement a cyber-attack. Much work has been dedicated to identifying the security vulnerabilities and recommending mitigation techniques associated with different sensors, controllers, and connection mechanisms, respectively. However, there is an absence of comprehensive and in-depth studies to identify how the cyber-attacks exploit the vehicles vulnerabilities to negatively impact the performance and operations of CAV. In this survey, we set out to thoroughly review the security issues introduced by AV and CV technologies, analyze how the cyber-attacks impact the performance of CAV, and summarize the solutions correspondingly. The impact of cyber-attacks on the performance of CAV is elaborated from both viewpoints of intra-vehicle system and inter-vehicle system. We pointed out that securing the perception and operations of CAV would be the top requirement to enable CAV to be applied safely and reliably in practice. Also, we suggested to utilize cloud and new AI methods to defend against smart cyber-attacks on CAV.

This paper develops a two-layer optimization approach that provides energy-optimal control for vehicles and traffic signal controllers. The optimizer in the first layer computes the traffic signal timings to minimize the total energy consumption levels of approaching vehicles from upstream traffic. The traffic signal optimization can be easily implemented in real-time signal controllers, and it overcomes the issues in the traditional Webster’s method of overestimating the cycle length when the traffic volume-to-capacity ratio exceeds 50 percent. The second layer optimizer is the vehicle speed controller, which calculates the optimal vehicle brake and throttle levels to minimize the energy consumption of individual vehicles. The A-star dynamic programming is used to solve the formulated optimization problem in the second layer to expedite the computation speed so that the optimal vehicle trajectories can be computed in real-time and can be easily implemented in simulation software for testing. The proposed integrated controller is first tested on an isolated signalized intersection, and then an arterial network with multiple intersections to investigate the performance of the proposed controller under various traffic demand levels. The test results demonstrate that the proposed integrated controller can greatly improve energy efficiency with fuel savings up to 17.7%, at the same time enhancing traffic mobility by up to 47.18% reduction in traffic delay and up to 24.84% reduction in vehicle stops.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

Nowadays, people like to travel to alleviate the stress and depression in their busy lives, and if they can do so at a low cost, it will be even more beneficial to them. The usual way for a traveler to book a ticket or to contact a travel agency is to book a ticket. It becomes more expensive for travelers. Due to the lack of vehicle management, travel agencies don’t get their appropriate profit. In this journal, we have provided proficient solutions for vehicle optimization to minimize travel costs. However, when travelers want to travel, they don’t find a proper tour guide, and it is sometimes expensive to arrange a proper tour guide. Moreover, travelers often don’t find a suitable package, and occasionally they do not know the place where they may want to visit. In this paper, we have discussed how we used effective methods to reduce vehicle costs for tour purposes. Further, we have developed a solution where bus seats are optimally occupied, and the package system and tour guide are included in it. We have also added a blog portal to our web-based software to introduce all tourist places and their information. In this journal, the proposed optimal vehicle usage system has been developed using Hypertext Markup Language (HTML), Cascading Style Sheets (CSS), the Tailwind Framework, React, and Node.js.

Vehicle identification is an important task in traffic monitoring because it allows for efficient inference and provides a cause for action. Vehicle classification via deep learning and other approaches such as segmentation is a critical tool for re-identification. In this paper, instance segmentation is used to identify vehicle makes with license plate detection, allowing for better unique vehicle recognition for re-identification. A dataset is annotated and modified, for example, by segmenting it with polygonal bounding boxes that capture the vehicle's unique frontal features. In addition, license plate localization is performed. The results showed improved classification as well as a high mAP for the dataset when compared to previous approaches based on CNN and deformed CNN. Furthermore, a deep residual network and fully connected layer-based classification were utilized as the backbone for feature representation. Instance segmentation detects objects by segmenting and classifying regions of interest. The imbalance in the dataset is resolved using a mosaic-tiled approach, which produces greater precision than other approaches.

This paper presents a study on the idle vibration reduction of a diesel sport utility vehicle (SUV). To reduce idle vibration, the transmission paths of vibration from the engine to the driver seat floor were investigated with the vehicle components related to idle vibration. Furthermore, operational deflection shape (ODS) tests were conducted to visualize the vibration shapes during engine idling. Experimental modal analyses were performed to obtain the natural frequencies and mode shapes. Through the ODS and modal tests, the vibration characteristics of the diesel SUV during idling were identified. Considering these vibration characteristics, a multi-body dynamic model for the diesel SUV described by differential equations of motion was established to evaluate the idle vibration. To implement the dynamic model effectively, the equivalent stiffnesses and damping coefficients included in the model were determined experimentally or analytically. The established dynamic model was verified by comparing the natural frequencies and idle vibration levels between simulations. Using this dynamic model, we analyzed the effects of various design variables on idle vibration and obtained an optimal design for reducing the idle vibration level. Finally, we present a design guide to reduce the idle vibration for diesel SUVs.

Over the past decade, wireless communication technologies have developed significantly for intelligent applications in road transport. This paper provides an overview of telecommunications-based intelligent transport systems with a focus on ensuring system safety and resilience. In vehicle-to-everything, these problems are extremely acute due to the specifics of the operation of transport networks, which requires the use of special protection mechanisms. In this regard, it was decided to use blockchain as a system platform to support the needs of transport systems for secure information exchange. This paper describes the technological aspects of implementing blockchain technology in vehicle-to-network; the features of such technology are presented, as well as the features of their interaction.

In the field of autonomous vehicles, lane detection and control plays an important role. In autonomous driving the vehicle has to follow the path to avoid the collision. A deep learning technique is used to detect the curved path in autonomous vehicles. In this paper a customized lane detection algorithm was implemented to detect the curvature of the lane. A ground truth labelling tool box for deep learning is used to detect the curved path in autonomous vehicle. By mapping point to point in each frame 80-90% computing efficiency and accuracy is achieved in detecting path.

The energy yield of the Vehicle-integrated photovoltaic (VIPV) differs from that of the standard photovoltaics (PV). It is mainly by the difference of the solar irradiance onto the car-roof and car-bodies as well as its curved-shape. Both meaningful and practical modeling and measurement of the solar irradiance for VIPV are needed to be newly established, not the extension of the current technologies. The solar irradiance was modeled by a random distribution of the shading objects and car-orientation with the correction of the curved surface of the PV modules. The measurement of the solar irradiance onto the car-roof and car-body was done using five pyranometers in five local axes on the car for one year. The measured dynamic solar irradiance onto the car-body and car-roof was used for validation of the solar irradiance model in the car.

Recently, inter-vehicle communication, which helps to avoid collision accidents (by driving safety support system) and facilitate self-driving (by dissemination of road and traffic information), has attracted much attention. In this paper, in order to efficiently collect road / traffic information in the request / response manner, first a basic method, Content-centric network (CCN) for Vehicular network (CV), is proposed, which applies CCN cache function to inter-vehicle communication. Content naming and routing, which take vehicle mobility into account, are investigated. On this basis, the CV method is extended (named as ECV) to avoid the cache miss problem caused by vehicle movement, and is further enhanced (named as ECV+) to more efficiently exploit cache buffer in vehicles, caching content according to a probability decided by channel usage rate. Extensive evaluations on network simulator Scenargie, with realistic open street map, confirm that the CV method and its extensions (ECV, ECV+) effectively reduce the average number of hops of data packets (by up to 47%, 63%, 83% respectively) and greatly improve the content acquisition success rate (by up to 356%, 444%, 689%, respectively), compared to the method without cache mechanism.

Estimating the vehicle crashworthiness parameters experimentally is expensive and time consuming. For these reasons different modelling approaches are utilized to predict the vehicle behaviour and reduce the need for full-scale crash testing. The earlier numerical methods used for vehicle crashworthiness analysis were based on the use of lumped parameters models (LPM), a combination of masses and nonlinear springs interconnected in various configurations. Nowadays, the explicit nonlinear finite element analysis (FEA) is probably the most widely recognized modelling technique. Although informative, finite element models (FEM) of vehicle crash are expensive both in terms of man-hours put into assembling the model and related computational costs. A simpler analytical tool for early analysis of vehicle crashworthiness could greatly assist the modelling and save time. In this paper a simple piecewise LPM composed of a mass-spring-damper system, is used to estimate the vehicle crashworthiness parameters, focusing on the dynamic crush and the acceleration severity index (ASI). The model is first calibrated against a full-scale crash test and a FEM, post-processed with the LS-DYNA software, at an impact velocity of 56 km/h. The genetic algorithm is used to calibrate the model by estimating the piecewise lumped parameters (stiffness and damping of the front structure of the vehicle). After calibration, the LPM is applied to a range of velocities (40, 48, 64 and 72 km/h). The predictions for crashworthiness parameters from the LPM were compared with the predictions from the FEA and the results are much similar. It is shown that the LPM can assist in crash analysis, since LPM has some predictive capabilities and requires less computation time in comparison with the explicit nonlinear FEA.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

Wind loads have become one of the key influence factors for the running safety of vehicles and comfort of passengers. Investigation on the wind speed spectrum characteristics of a moving vehicle under turbulent crosswinds is of great influence. Expressions of the wind speed spectrum of a moving vehicle was obtained from the von Kármán spectrum based on Taylor’s frozen flow hypothesis. The influence factors, including the ratio of the vehicle speed to the wind speed and the wind yaw angle from 15° to 175°, were analyzed. The maximum value of the wind speed spectrum and the corresponding frequency were studied as well. The results show that the maximum values of the wind speed spectrum of the moving vehicle were larger than those of the static vehicle. The maximum value of the wind speed spectrum corresponding to the moving vehicle first increased and then decreased as the wind yaw angle increased. Some of the frequencies corresponding to the longitudinal wind speed spectrum values of the moving vehicles were smaller than those of the static vehicle. For moving vehicles, the frequency values corresponding to the maximum values of the longitudinal wind speed spectrum first increased and then decreased as the ratio of the vehicle speed to the wind speed and the wind yaw angle increased.

The key to ensuring the sustainability of transportation operations on the roads is to manage traffic flows homogeneously. By homogenizing the behavior of various drivers, traffic operation can be optimized, and traffic safety can be improved. However, the advent of autonomous vehicles is expected to have a major impact on the homogeneity of sustainable transportation operations. In this study, a method of driving in harmony with surrounding vehicles was studied to minimize the impact of autonomous vehicles on current traffic operation. In particular, in this study, a methodology was developed to optimize the driving behavior of autonomous vehicles by analyzing the driving behavior of following vehicles using spectrum analysis. Specifically, a method for calculating three indicators that can analyze the driving behavior of a following vehicle, such as reaction time, stimulus adaptation index, and collision risk avoidance index, was proposed. These indices produced consistent and robust results for all traffic conditions. If these indicators are used, it is expected that sustainable traffic management will be possible even when autonomous vehicles and human drivers are mixed on the road.

We consider the problem of coordinating the charging of an entire fleet of electric vehicles (EV), using a model-free approach, i.e. purely data-driven reinforcement learning (RL). The objective of the RL-based control is to optimize charging actions, while fulfilling all EV charging constraints (e.g. timely completion of the charging). In particular, we focus on batch-mode learning and adopt fitted Q-iteration (FQI). A core component in FQI is approximating the Q-function using a regression technique, from which the policy is derived. Recently, a dueling neural networks architecture was proposed and shown to lead to better policy evaluation in the presence of many similar-valued actions, as applied in a computer game context. The main research contributions of the current paper are that (i)we develop a dueling neural networks approach for the setting of joint coordination of an entire EV fleet, and (ii)we evaluate its performance and compare it to an all-knowing benchmark and an FQI approach using EXTRA trees regression technique, a popular approach currently discussed in EV related works. We present a case study where RL agents are trained with an epsilon-greedy approach for different objectives, (a)cost minimization, and (b)maximization of self-consumption of local renewable energy sources. Our results indicate that RL agents achieve significant cost reductions (70--80%) compared to a business-as-usual scenario without smart charging. Comparing the dueling neural networks regression to EXTRA trees indicates that for our case study's EV fleet parameters and training scenario, the EXTRA trees-based agents achieve higher performance in terms of both lower costs (or higher self-consumption) and stronger robustness, i.e. less variation among trained agents. This suggests that adopting dueling neural networks in this EV setting is not particularly beneficial as opposed to the Atari game context from where this idea originated.

Scientific and technological advances in telecommunications and onboard electronics, and advances in sustainability standards, dictated major changes to various industrial sectors, including the automotive industry, where hard and soft approaches to manufacturing are vying for market dominance. This work presents a prospective analysis of the autonomous vehicle (AV) market, analyzing three of the main US AV technology firms, Tesla, Waymo and Apple. Their designs and solutions are compared, and prospective scenarios were constructed based on an analysis of their strengths, weaknesses, opportunities and threats (SWOT). The results suggest that Tesla currently exhibits the greatest market leadership in the group studied. However, it was concluded that in the medium term, Waymo would surpass Tesla and assume market leadership. In the long run, it was concluded that Apple will overcome its rivals and dominate this market.

In the rescue operations the full time of action plays important role. It is a sum of planning, travel, and manipulation (in the action place) phases times. The time minimization of first two phases by autonomous vehicle for remote action is considered in the paper. For known a priori map the path planning consists of local optimal decision collected next in the general algorithm of the optimal path. Such approach significantly reduces time of path planning. The robot features and known sparse obstacles reduce the allowable robot speeds. The time of travel is calculated from allowable velocity profile. So, it can be used to estimate the travel performance. Genetic algorithm and random search-based methods for path finding with travel time optimization are exploited and compared in the paper. All the proposed time optimisation solutions of rescue operation are checked during computer simulations and results of simulation are presented.

Background: According to the National Highway Traffic Safety Administration, 116 pedestrians were killed in motor vehicle crashes in Ohio in 2015. However, no study to date has analyzed crashes in Ohio exploring the factors contributing to the pedestrian injury severity resulting from motor vehicle crashes. This study fills this gap by investigating the crashes involving pedestrians exclusively in Ohio. Materials and Methods: This study uses the crash data from the Highway Safety Information System, from 2009 to 2013. The explanatory factors include the pedestrian, driver, vehicle, crash, and roadway characteristics. Both fixed- and random-parameters ordered probit models of injury severity (where possible outcomes are major, minor, and possible/no injury) were estimated. Results: The model results indicate that being older pedestrian (65 and over), younger driver (less than 24), driving under influence (DUI), being struck by truck, dark-unlighted roadways, six-lane roadways, and speed limit of 40 mph and 50 mph were associated with more severe injuries to the pedestrians. Conversely, older driver (65 and over), passenger car, crash occurring in urban locations, daytime traffic off-peak (10 AM to 3:59 PM), weekdays, and daylight condition were associated with less severe injuries. Conclusion: This study provides specific safety recommendations so that effective countermeasures could be developed and implemented by the policy makers, which in turn will improve overall highway safety.

In this paper we present the exploration of indoor positioning technologies for UAVs, and navigation techniques for path planning and obstacle avoidance. The objective is to perform warehouse inventory tasks using a drone to search for barcodes or markers to identify the objects. For the indoor positioning techniques, we employ Visual-Inertial Odometry (VIO), Ultra-Wideband (UWB), AprilTag fiducial markers, and Simultaneous Localization and Mapping (SLAM). These algorithms encompass global positioning, local positioning, and pre-mapping positioning, comparing the merits and drawbacks of various techniques and trajectories. In UAV navigation, we combine SLAM-based RTAB-Map indoor mapping and navigation path planning of the ROS for indoor environments. This system enables precise drone positioning indoors and utilizes global and local path planners to generate flight paths that avoid dynamic, static, unknown, and known obstacles, demonstrating high practicality and feasibility. To achieve the warehouse inventory inspection, a reinforcement learning approach is proposed to recognize the markers by adjusting the UAV's viewpoint. We address several main problems in inventory management, including efficiently planning paths while ensuring a certain level of detection rate. Two reinforcement learning techniques, AC (Actor-Critic) and PPO (Proximal Policy Optimization), are implemented based on AprilTag identification. Testing is performed in both simulated and real-world environments, and the effectiveness of the proposed method is validated.Code is available at https://github.com/kellen080/Navigation and https://github.com/kellen080/Indoor\_Positioning.

Traditional path planning algorithms have drawbacks in unmanned vehicle path planning, such as low efficiency, unsuitability for dynamic environments, and high computational complexity. To address these issues, this paper proposes a dynamic path planning method for unmanned vehicles that combines the A* algorithm with an improved Dynamic Window Approach (DWA). Firstly, a collision risk function is incorporated into the DWA algorithm to evaluate scores based on the braking distance corresponding to the current vehicle speed and the distance to obstacles, determining whether timely braking or obstacle avoidance is feasible. The earlier the braking or obstacle avoidance, the higher the score, thereby enhancing the evaluation algorithm of the DWA. Secondly, the key points extracted by the A* algorithm are used as temporary target points for the DWA algorithm, reducing the eight search directions to five. Finally, the key points of the A* algorithm’s path are set as the temporary end points for the DWA algorithm, integrating the two algorithms to plan a smoother curved path that can avoid unknown and dynamic obstacles. Simulation data demonstrates that compared to traditional artificial potential field methods, RRT, and Dijkstra’s algorithm, the new fusion algorithm reduces time by 11.71 seconds, a decrease of 6.9%, and shortens path length by 3.093 meters, a reduction of 4.16%, while increasing average linear velocity by 2.9%. The proposed algorithm ensures smoother paths while also making paths more rational and efficient

Anticipating and planning for the urgent response to large-scale disasters is critical to increase the probability of survival in these events. These incidents present various challenges that complicate the response, such as unfavorable weather conditions, difficulties in accessing affected areas, and the geographical spread of the victims. Furthermore, local socioeconomic factors such as insufficient prevention education, limited disaster assets, and inadequate coordination between public and private emergency services may complicate these situations. In large-scale emergencies, multiple hotspots are usually observed, which requires efforts to coordinate the strategic allocation of human and material resources in different geographical areas. Therefore, the precise management of these resources based on the specific needs of each area becomes fundamental. To address these complexities, this paper proposes a methodology that models these scenarios as an optimization problem, focusing on the location and allocation of resources in mass casualty incidents. The proposed case study is Mexico City in a post-earthquake scenario, using voluntary geographic information, open government data, and historical data from the September 19, 2017 earthquake. Additionally, it is assumed that the resources that require optimal location and allocation are ambulances, which focus on medical issues that affect the survival of victims. The designed solution involves the use of a metaheuristic optimization technique, along with a parameter tuning technique, to find configurations that perform at different instances of the problem, i.e., different hypothetical scenarios that can be used as a reference for future possible situations. Finally, the objective is to present the different solutions graphically, accompanied by relevant information to facilitate the decision-making process of the authorities responsible for the practical implementation of these solutions.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

The software design of autonomous vehicles (AVs) incorporates artificial intelligence (AI) characteristics to enhance their safety and overall driving performance. Central to vehicle’s operation is the ability to reason effectively in complex and uncertain environments. However, traditional logical systems, such as monotonic logic, often struggle to handle the inherent uncertainties and exceptions encountered in real-world scenarios. This paper proposes the utilization of non-monotonic logic in order to enhance the reasoning capabilities of autonomous vehicles. By incorporating non-monotonic reasoning, vehicles can navigate intricate traffic scenarios, make plausible inferences, and adapt their decisions when faced with conflicting information. This research aims to provide a comprehensive review of non-monotonic logic's application in autonomous vehicles, highlighting its advantages over traditional logical systems and its potential impact on safety and performance. Additionally, through this research, we seek to contribute to the advancement of autonomous driving technology by enhancing the reasoning capabilities of vehicles in various scenarios, such as car- following related to critical safety events. The personalized cognitive agent is proposed in driving behavior to consider particularly in their assumptions of homogeneous drivers. The personalized cognitive agent is incorporating heterogeneous driving behaviors, based on individual user preferences, characteristics, and needs. Driving behavior is a complex interplay of various factors, encompassing both human and external elements. Human factors, including age, experience, and gender, contribute significantly to how individuals navigate the roads. These factors influence decisions, reactions, and risk-taking tendencies on the part of drivers. Additionally, external factors such as weather conditions further compound this intricate dynamic, requiring drivers to adapt their behavior to the prevailing environment. The goal of a personalized cognitive agent is to provide tailored and customized experiences to cognitive vehicles, taking into account the unique requirements and individual preferences of occupants inside autonomous vehicles.

Raman spectroscopy is a type of inelastic scattering that provides rich information about a sub-stance based on the coupling of the energy levels of their vibrational and rotational modes with incident light. It has been applied extensively in many fields. As there is an increasing need for remote detection of chemicals in planetary exploration and anti-terrorism, it is urgent to develop a compact and easily transportable fully automated remote Raman detection system for trace detection and identification of information with high-level confidence about the target’s compo-sition and conformation in real-time and for real field scenarios. Here, we present an unmanned vehicle-based remote Raman system, which includes a 266 nm air-cooling passive Q-switched nanosecond pulsed laser of high-repetition frequency, a gated ICMOS, and an unmanned vehicle. This system obtains good spectral signals from remote distances ranging from 3 m to 10 m for simulating realistic scenarios, such as aluminum plate, woodblock, paperboard, black cloth, and leaves, and even for detected amounts as low as 0.1 mg. Furthermore, a CNN-based algorithm is implemented and packaged into the recognition software to achieve fast and more accurate de-tection and identification. This prototype provides a proof-of-concept for an unmanned vehicle with accurate remote substance detection in real-time, which can be helpful for remote detection and identification of hazardous gas, explosives, their precursors, and so forth.

This study focuses on the recently emerged Internet of Vehicles (IoV) concept to provide an integrated agricultural vehicle/machinery tracking system through two leading low power wide area network (LPWAN) technologies, namely LoRa and NB-IoT. The main aim is to investigate the theoretical coverage limits by considering the urban, suburban, and rural environments. Two vehicle tracking units (VTUs) have been designed for LoRa and NB-IoT connectivity technologies that can be used as reference hardware in coverage analysis. On this basis, the closed-form explicit analytical expressions of the maximum transmission range have been derived using the Hata path loss model. Besides, the computer simulation results have been validated via the maps from XIRIO online radio planning tool. In light of the obtained findings, several evaluations have been made to enhance the LPWAN-based agricultural vehicle tracking feasibility in smart farms.

The connectivity level of last-generation vehicles is constantly on the rise. The combined use of Vehicle-To-Everything (V2X) connectivity and autonomous driving can provide remarkable benefits through the optimization of the route and speed trajectory. In this framework, this paper focuses on vehicle eco-driving optimization in a connected environment. The virtual test rig of a premium segment passenger car was used for generating the simulation scenarios. The benefits, in terms of energy and time savings, that the introduction of V2X communication, integrated with cloud computing, can have in a real-world scenario were assessed. The Reference Scenario is a pre-defined Real Driving Emissions (RDE) compliant route, while the simulation scenarios were generated by assuming two different penetration levels of V2X technologies. The associated energy minimization problem is formulated and solved by means of a global optimization algorithm, i.e., Dynamic Programming (DP). The optimization framework includes information coming from the surrounding environment, e.g., traffic lights state, speed limits, distance to travel, etc. The simulations show that introducing a smart infrastructure along with optimizing the vehicle speed in a real-world route can potentially reduce the required energy by 54% while shortening the travel time by 38%. Finally, a sensitivity analysis is performed on the bi-objective optimization cost function to find a set of Pareto optimal solutions, between energy and travel time minimization.

Cellular Vehicle-to-Everything (C-V2X) is a communication technology that supports various safety, mobility, and environmental applications given its higher reliability properties compared to other communication technologies. The performance of these C-V2X-enabled Intelligent Transportation System (ITS) applications is affected by the performance of the C-V2X communication technology (mainly packet loss). Similarly, the performance of the C-V2X communication is dependent on the vehicular traffic density which is affected by the traffic mobility patterns, and vehicle routing strategies. Consequently, it is critical to develop a tool that can simulate, analyze, and evaluate the mutual interactions of the transportation and communication systems at the application level and to the evaluate the benefits of the C-V2X enabled ITS applications. In this paper, we demonstrate the benefits gained when using C-V2X Vehicle-to-Infrastructure (V2I) communication technology in an energy-efficient dynamic routing application. Specifically, we develop a Connected Energy-Efficient Dynamic Routing (C-EEDR) application using C-V2X as a communication medium in an integrated vehicular traffic and communication simulator (INTEGRATION). The results demonstrate that the C-EEDR application achieves fuel savings of up to 16.6% and 14.7% in the IDEAL and C-V2X communication cases, respectively for a peak hour demand on the downtown Los Angeles network considering a 50% level of market penetration of connected vehicles. The results demonstrate that the fuel savings increase with increasing levels of market penetration at lower traffic demand levels (25% and 50% the peak demand). At higher traffic demand levels (75% and 100%) the fuel savings increase with increasing levels of market penetration with maximum benefits at a 50% market penetration rate. Although the communication system is affected by the high density of vehicles at the high traffic demand levels (75% and 100% the peak demand), the C-EEDR application manages to perform reliably producing system-wide fuel consumption savings.The C-EEDR application achieves fuel savings of 15.2% and 11.7% for the IDEAL communication and 14% and 9% for the C-V2X communication at the 75% and 100% market penetration rates, respectively. Finally, the paper demonstrates that the C-V2X communication constraints only affect the performance of the C-EEDR application at the full demand level when the market penetration of connected vehicles exceeds 25%. This degradation, however is minimal (less than a 2.5% reduction in fuel savings).

The gravel road pavement has a lower construction cost but poorer performance than the asphalt surface. It also emits dust and deforms under the impact of vehicle loads and ambient air factors. The resulting ripples and ruts are constantly deepening, increasing vehicle vibrations and fuel consumption, reducing safe driving speed and comfort. In this article, existing pavement quality evaluation indexes are analysed, and a methodology for their adaptation for roads with gravel pavement is proposed. This article reports the measured wave depth and length of the gravel pavement profile by the straightedge method of a 160 m long road section in three road exploitation stages. The measured pavement elevation was processed according to ISO 8608, and vehicle frequency response has been investigated using simulations in MATLAB/Simulink. The applied International Roughness Index (IRI) analysis showed that a speed of 30-45 km/h instead of 80 km/h provides the objective results of IRI calculation on the flexible pavement due to a decreasing velocity of vehicle's unsprung mass on a more deteriorated road pavement state. The influence of the corrugation phenomenon of gravel pavement has been explored, identifying specific driving safety and comfort cases. Finally, an increase in the Dynamic Load Coefficient (DLC) at a low speed of 30 km/h on the most deteriorated pavement and a high speed of 90 km/h on the middle-quality pavement demonstrates the demand for timely gravel pavement maintenance and the complicated prediction of a safe driving speed for drivers.

Given the high number of vehicle-crash victims, it has been established as a priority to reduce this figure in the transportation sector. For this reason, many of the recent researches are focused on including control systems in existing vehicles, to improve their stability, comfort and handling. These systems need to know in every moment the behavior of the vehicle (state variables), among others, when the different maneuvers are performed, to actuate by means of the systems in the vehicle (brakes, steering, suspension) and, in this way, to achieve a good behavior. The main problem arises from the lack of ability to directly capture several required dynamic vehicle variables, such as roll angle, from low-cost sensors. Previous studies demonstrate that low-cost sensors can provide data in real-time with the required precision and reliability. Even more, other research works indicate that neural networks are efficient mechanisms to estimate roll angle. Nevertheless, it is necessary to assess that the fusion of data coming from low-cost devices and estimations provided by neural networks can fulfill the reliability and appropriateness requirements for using these technologies to improve overall safety in production vehicles. Because of the increasing of computing power, the reduction of consumption and electric devices size, along with the high variety of communication technologies and networking protocols using Internet have yield to Internet of Things (IoT) development. In order to address this issue, this study has two main goals: 1) Determine the appropriateness and performance of neural networks embedded in low-cost sensors kits to estimate roll angle required to evaluate rollover risk situations. 2) Compare the low-cost control unit devices (Intel Edison and Raspberry Pi 3 Model B), to provide the roll angle estimation with this artificial neural network-based approach. To fulfil these objectives an experimental environment has been set up composed of a van with two set of low-cost kits, one including a Raspberry Pi 3 Model B, low cost Inertial Measurement Unit (BNO055 - 37€) and GPS (Mtk3339 - 53€) and the other having an Intel Edison System on Chip linked to a SparkFun 9 Degrees of Freedom module. This experimental environment will be tested in different maneuvers for comparison purposes. Neural networks embedded in low-cost sensor kits provide roll angle estimations very approximated to real values. Even more, Intel Edison and Raspberry Pi 3 Model B have enough computing capabilities to successfully run roll angle estimation based on neural networks to determine rollover risks situation fulfilling real-time operation restrictions stated for this problem.

In the current complex and uncertain macroeconomic situation, improving the inherent resilience of the new energy vehicle industry chain is the key to effectively addressing various risks and challenges, and achieving dynamic balance between high-quality industrial development and industrial chain security. Based on the basic concept of resilience and the actual situation of new energy vehicle industry chain development, this study constructs a comprehensive evaluation index system for the resilience of the new energy vehicle industry chain, which includes four dimensional first-level indicators of coping resistance, adaptive resilience, autonomous control and leading competitiveness. In addition, it is measured by combining the data related to the new energy vehicle industry chain in Changzhou City. Our study shows that the situation on the new energy vehicle industry chain is complicated, and the comprehensive evaluation index system is more favorable for evaluating its resilience level.

This work targets the development of a mobility control system for high-speed series hybrid electric tracked vehicles, which operate with independent traction motors for each track. The scope of the research encompasses the modeling of the series hybrid powertrain specific to military tracked vehicles, as well as an in-depth analysis of their dynamic behavior. Subsequently, the study conducts a critical review of the mobility control approaches sourced from literature, identifying key techniques relevant to high-inertia vehicular applications. Building on the foundational models, the study puts forward a robust closed-loop mobility control system aimed at ensuring precise and stable off-road vehicle operations. The system's resilience and adaptability to a variety of driving conditions are emphasized, with a particular focus on handling maneuvers such as steering and pivoting, which are challenging operations for tracked vehicle agility. The performance of the proposed mobility control system is tested through a series of simulations, covering a spectrum of operational scenarios. These tests are carried out in both offline simulation settings, which permit meticulous fine-tuning of system parameters, and real-time environments that replicate actual field conditions. The simulation results demonstrate the system's capacity to improve vehicular response and highlight its potential impact on the future designs of mobility control systems for the heavy-duty vehicle sector, particularly in defense applications.

Driver’s distractions are more prone to occur with automated driving vehicles, which might turn into cancelling some of their advantages. Traffic reports, naturalistic observations and in-lab tests are carried out to determine the influence of driver’s distractions in car crashes and to develop technology to detect and prevent them from happening. One of the best strategies to cope with this problem is education. In this work we propose a simulation environment to design laboratory experiments to study driver’s distractions as well as simple games to train drivers to take over the control of the vehicle when required. The result framework enables drivers to experience driving highly automated cars in their neighborhoods or in places of their choice with different levels of events to check their ability in taking over the control when required.

Addressing sustainable mobility in urban areas has become a priority in today’s society, given the growing population and increasing vehicular flow in these areas. Intelligent Transportation Systems have emerged as innovative and effective technological solutions to address these challenges. Research in this area has become crucial, as it contributes not only to improve mobility in urban areas, but also to positively impact the quality of life of its inhabitants. To address this, a dynamic clustering methodology for vehicular trajectory data is proposed which can provide an accurate representation of the traffic state. Data was collected for the city of San Francisco, a dynamic clustering algorithm was applied and then an indicator was applied to identify areas with traffic congestion. Several experiments were also conducted with different parameterizations of the forgetting factor of the clustering algorithm. The results showed in terms of precision that the dynamic clustering methodology achieved high match rates compared to the congestion indicator applied to static cells.

The unsupervised domain-adaptive vehicle reidentification approach aims to transfer knowledge from a labeled source domain to an unlabeled target domain, however there are knowledge differences between the target domain and the source domain. To reduce domain differences, existing unsupervised domain-adaptive rerecognition methods generally require access to the source domain data to assist in re-training the target domain model. But for security reasons, in many cases, data between different domains cannot communicate. To this end, this paper proposes an unsupervised domain-adaptive vehicle re-identification method based on source-free knowledge transfer. First, by constructing a passive domain knowledge migration module, the target domain is consistent with the source domain model output to train a generator to generate the "source-like samples". Then, it can effectively reduce the model knowledge difference and improve the model generalization performance. According to the experiment and testing of VeRi776 and VehicleID, two mainstream public data sets in this field, the rank-k and mAP indexes obtained are both improved, and are suitable for object re-recognition tasks without source data.

The dependence on Unmanned Aerial Vehicles (UAVs) has dramatically increased in many sectors around the globe. UAVs are in high demand, and their technology is developing quickly due to their sophisticated ability to handle various issues. UAVs are capable of replacing labor-intensive tasks with conducive and safe regulation. Additional tools or sensors need to be added to the UAVs system to ensure the implementation of UAVs able to serve into industrial level. The paper aims to consolidate and present a thorough understanding of the various stages of image processing pipelines deployed in UAV applications, including image acquisition, preprocessing, feature extraction, object detection and tracking, and decision-making processes. Throughout this paper, several aspects were deliberate such as strengths, limitations, and performance metrics of existing approaches, this paper seeks to provide researchers, engineers, and practitioners with valuable insights into the challenges and opportunities of image processing systems for UAVs. Ultimately, the synthesis of this knowledge will contribute to enhancing the effective-ness, autonomy, and applicability of UAVs in diverse fields such as surveillance, agriculture, disaster management, and environmental monitoring.

Navigation is the most challenging issue in autonomous vehicles. Researchers in the current era have developed many Artificial Intelligence techniques to navigate, generate paths, and avoid obstacles for optimum path planning for autonomous vehicles. Different studies have investigated bio-inspired techniques to overcome the navigation issue, including obstacle avoidance. This paper uses new meta-heuristic optimization techniques called Dragonfly Algorithm (DA) to set the goal by detecting and avoiding obstacles with minimum human interference. For effective results, the Dragonfly-Fuzzy hybrid algorithm is analyzed over the unstructured environment because individual techniques may not be sure of an optimal solution over all configurations. The main advantage of the proposed hybrid controller is that it combines the multiple features of different approaches into a single controller. This paper compares simulation and experimental findings over various environmental conditions to the individual algorithm. Regarding time and path optimization, the hybrid Dragonfly-Fuzzy controller performs better than the respective controller.

The number of people owning vehicles has been steadily growing, resulting in increased numbers of vehicles on the roads, making roads more congested, and increasing the risk of accidents. In addition, heavy rain, snow, and fog have increased due to abnormal weather caused by global warming. These bad weather conditions can also affect the safety of vehicles and drivers. The need to disseminate safety messages on the social internet of vehicles due to these problems has been steadily increasing. In this paper, we propose an efficient safety message dissemination scheme that focuses on urban environments with high vehicle density and mobility to address these problems. The proposed scheme reduces packet loss by considering frequent cluster departures and subscriptions through an efficient cluster management technique. In a vehicle-to-vehicle environment, the dissemination of safety messages is divided into an intra-cluster and an inter-cluster emergency as well as general safety message dissemination technique. In a vehicle to infrastructure environment, the proposed scheme reduces the number of processing requests and duplicate messages made to roadside units (RSUs) through a request operation process for each vehicle and an RSU scheduling technique. We conducted several performance evaluations of message packet loss and the number of RSU processing requests to demonstrate the superiority of the proposed scheme.

Leader-follower autonomy (LFA) systems have so far only focused on vehicles following other vehicles. Though there have been several decades of research into this topic, there has not yet been any work on human-vehicle leader-follower systems. We present a system in which an autonomous vehicle — our ACTor 1 platform — can follow a human leader who controls the vehicle through gestures. We successfully developed a modular pipeline that uses artificial intelligence/deep learning to recognize hand-and-body gestures from a user in view of the vehicle’s camera and translate those gestures into physical action by the vehicle. We demonstrate our work using our ACTor 1 platform, a modified Polaris Gem 2 electric vehicle. This work has numerous applications, such as material transport in industrial contexts.