As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

Objective: Mechanical bowel preparation is essential for the visualisation of the colon during colonoscopy, and previous studies have identified changes in gut microbiota composition after bowel preparation and colonoscopy. Considering the gut microbiota is increasingly implicated in mood, we aimed to explore the potential impact of this intervention on mood and the microbiota-gut-brain axis. Methods: We conducted a pre-post intervention study, with timepoints of one week before and one month after bowel preparation and colonoscopy, in community-dwelling adults referred for colonoscopy. Our primary outcome was change in average Hospital Anxiety and Depression Scale depression sub-scores using generalised estimating equations. We also examined changes in average anxiety, stress, and quality of life scores, and faecal microbiota composition and potential function using 16S rRNA sequencing. We further explored associations between changes in depressive symptoms and the gut microbiota and conducted post-hoc analyses to explore potential effect modifiers. Key Results: 59 participants were included in the analyses. Depressive symptoms decreased one-month post-procedure compared to baseline (adjusted β=−0.64; 95%CI: −1.18, −0.11). Irritable bowel syndrome (IBS) appeared to moderate this relationship (1.78; 0.292, 3.26); depressive symptoms increased in those with, and decreased in those without, IBS. Changes in gut microbiome composition included reduced alpha diversity, modest effects on beta-diversity, and increases in genera associated with potential health benefits, one-month post-procedure compared to baseline. Increases in the CLR-transformed abundance of Ruminococcaceae UCG-009 were associated with improvements in depressive symptoms. Conclusions: There is preliminary evidence of a potential mental health effect of bowel preparation and colonoscopy, which may be associated with changes to the gut microbiota. There may also be a differential mental health impact of this procedure for those with and without IBS. Considering the limitations of our study, further research is required to confirm these findings and their clinical relevance.

This study examined the impact of differences in fruit load of olive trees on the rate of stem refilling. The experiment was conducted in a commercial olive orchard over the consecutive years of 2021 and 2022, during which the biennial bearing cycle of olive trees resulted in minimal fruit production in 2021 and maximal production in 2022. The rate of stem refilling was determined by quantifying the differences in water volume traversing the apex and base of the principal branches of experimental trees using sap flow sensors. Concurrent measurements of tree water status were also conducted using psychrometers, while soil moisture content dynamics were continuously recorded. Results indicate that alternate bearing significantly influences the stem refilling process, while soil moisture availability also plays a pivotal role. Water reserves were more intensively utilized during the year of full production (“ON” year) primarily to fulfill the water demands of developing fruits. This replenishment occurred in various periods during the day, including early morning, afternoon, and night, when stomatal conductance measurements indicated stomatal closure. The study suggests a more intense replenishment of reserves during the night in "ON" year trees, irrespective of soil moisture, water vapor pressure deficit, or phenological fruit development stage.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

With the advent of Neural Machine Translation, the more the achievement of human-machine parity is claimed at WMT, the more we come to ask ourselves if their evaluation environment can be trusted. In this paper, we argue that the low quality of the source test set of the news track at WMT may lead to an overrated human parity claim. First of all, we report nine types of so-called technical contaminants in the data set, originated from an absence of meticulous inspection after web-crawling. Our empirical findings show that when they are corrected, about 5% of the segments that have previously achieved a human parity claim turn out to be statistically invalid. Such a tendency gets evident when the contaminated sentences are solely concerned. To the best of our knowledge, it is the first attempt to question the “source” side of the test set as a potential cause of the overclaim of human parity. We cast evidence for such phenomenon that according to sentence-level TER scores, those trivial errors change a good part of system translations. We conclude that to overlook it would be a mistake, especially when it comes to an NMT evaluation.

(1) Background: Since microplastics in the aquatic environment are difficult to prevent and can cause adverse physiological and biochemical reactions to various organisms, we aimed to analyze the effectiveness of an eco-friendly removal method using aquatic plants with high ornamental value and excellent water purification ability. (2) Methods: Iris pseudacorus and Lythrum anceps were planted in tap water contaminated with microplastics to analyze the removal rate and root adsorption of microplastics. (3) Results: The amount of microplastics in the planting boxes of Iris pseudacorus and Lythrum anceps was significantly reduced, and the adsorption of microplastics on the roots was confirmed. (4) Conclusions: It was found that the removal of microplastics in water by aquatic plants is effective and that microplastic pollution does not significantly affect plant growth. However, the removal of microplastics by adsorption on plant roots may be affected by various environmental factors, so it is necessary to consider various limitations.

Singapore, being a land-scarce country, is heavily dependent on imported food, which poses a challenge in ensuring food security. In addition, the substantial amount of food waste generated in Singapore further deepens food insecurity challenges, imposing enormous pressure on the country's food and land resources. In the recent years, valorising food waste streams into higher value products has been an increasing trend in tackling food wastage due to its economical and environmental benefits. This paper provides a thorough review on food waste valorisation in Singapore and summarizes critical information from the current food landscape to the food waste management strategies adopted. The review highlights the prototypes developed from food waste streams by the local research and development capabilities and the technological processing and techniques used for versatile applications ranging from food and nutraceuticals to urban agriculture. The challenges associated with the valorisation of food waste are also addressed. Two ambitious Initiatives by the Singapore government Zero Waste Plan and the 30-by-30 food security goal to encourage food waste valorisation are explored and presented. The review serves as a reference for other countries in ensuring food security and achieving sustainable development goals.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

This study investigates the cyclic load application impact on fly ash-based geopolymer composites that are reinforced with a low amount of fibre reinforcement. For reinforcement purposes, PVA and steel fibres are used. For testing purposes, four geopolymer composite mixes were made, 3 of which had fibre reinforcement. Simultaneously specimens were tested for shrinkage, static load-induced creep, and cyclic load-induced creep. For static and cyclic creep testing, specimens were loaded with 20% of their strength. For cyclic creep testing, load application and release cycles were seven days long. When each cycle was introduced, the load was added in steps. In 5 minutes, by 25% steps of the necessary load, the specimens were loaded or unloaded. Only plain specimens show that static creep strains are within cyclic creep strains. For all the other specimens, the static load is higher than the cyclic load-induced creep amplitude. Also, 1% PVA fibre-reinforced specimens show the most elastic characteristics under cyclic load, and 1% steel fibre-reinforced specimens appear to be the most resistant to the cyclic load introduction.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

The high penetration of distributed energy resources poses significant challenges to the dispatch and operation of power systems. Improving the accuracy of short-term load forecasting (STLF) can optimize grid management, leading to increased economic and social benefits. Currently, some simple AI and hybrid models has issues to deal with and struggle with multivariate dependencies, long-term dependencies, and non-linear relationships. This paper proposes a novel hybrid model for short-term load forecasting (STLF) that integrates multiple AI models with Lasso regression using the stacking technique. The base learners include ANN, XgBoost, LSTM, Stacked LSTM, and Bi-LSTM, while Lasso regression serves as the meta-learner. By considering factors such as temperature, rainfall, and daily electricity prices, the model aims to more accurately reflect real-world conditions and enhance predictive accuracy. Empirical analyses on real-world datasets from Australia and Spain show significant improvements in forecasting accuracy, with a substantial reduction in Mean Absolute Percentage Error (MAPE) compared to existing hybrid models and individual AI models. This research highlights the efficiency of the stacking technique in improving STLF accuracy, suggesting potential operational efficiency benefits for the power industry.

Monitoring training load, recovery, and wellness in maturation ages is even more relevant than in adulthood, especially during congested schedules. The objective of this study was to quantify and describe the differences in external and internal load, recovery, and perceived wellness in elite under-16 female players during a period of three competitions in seven days, based on their participation during matches. An observational design was used to quantify external load (total distance, high-speed distance, and PlayerLoad), internal load (differential sRPE), as well as recovery and wellness of 18 international under-16 players during a development tournament. The external load pattern of the starting players was undulating, with matches showing the highest internal load values compared to training sessions and non-starters. Non-starters players (whether training or matches) showed similar external load and differential sRPE values throughout the tournament (p>0.05). Starting players experienced higher internal load than non-starters during matches (p<0.037), without differences between training sessions (p>0.05). No changes were seen in wellness or recovery (all p-values >0.05), except for non-starters in session 3 compared to session 7 (p=0.024). Starting players had more weekly total minutes (p=0.018), differential sRPE (breath: p=0.002; leg: p=0.002; cognitive: p=0.003), total distance (p=0.003), and PlayerLoad (p=0.008) than non-starters. Our results indicate differing load patterns between starters and non-starters, which do not affect wellness and recovery differently. Starters accumulate more weekly total load. Coaches can use these findings to guide decisions and load compensations in high competition contexts for young female soccer players.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

This study focuses on calibrating the linear Drucker-Prager yield criterion for polypropylene under multiaxial loading conditions, using the Arcana machine to achieve a wide range of triaxiality states. The Drucker-Prager criterion has been adapted for polymers, composites, and metals due to its ability to account for the influence of hydrostatic pressure on yield stress. This study employs the Arcana machine, which allows for testing flat plate samples under various angles, thereby simulating different stress states from pure shear to biaxial tension. Additionally, uniaxial compression tests were conducted to extend the range of triaxiality. The material used in this study is Sabic 83MF10, a polypropylene polymer. Samples were prepared by injection molding and cut to specific dimensions. Tests were performed using a universal testing machine with the Arcana handle, and the results were analyzed to determine the yield strength, pressure, and triaxiality for each sample. The results showed a linear relationship between von Mises stress and hydrostatic pressure, with a friction angle (β) of 20.65° and material cohesion (d) of 27.81. The numerical simulations in Abaqus confirmed the validity of the Drucker-Prager model, accurately reflecting the moment of yielding for the tested samples.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land at a rate correlated with global population are an increas-ing cause of increasing atmospheric CO2 pressure (pCO2). This hypothesis widens the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels, causing greater atmos-pheric pCO2. Our modelling tests for reactions of dissolved inorganic carbon show that increasing atmospheric CO2 is caused thermodynamically by falling land surface pH values, but only with bicarbonate present. Strong acids generated by oxygen from re-duced inorganic compounds of nitrogen and sulphur emit CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils, between 6 to above 8. We show that each decrease of aqueous pH value of 0.01 units from acidification of sur-face water near pH 8 potentially increases the pCO2 in the atmosphere by about 7 ppmv. The surface pH value of the ocean near 8.10 in 2000 has been shown to decrease at this rate, a result of equilibrating with the rising atmospheric pCO2. Therefore, our qualita-tive estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. Unfortunately, these acidifying processes on land from excessive nitrogen fertiliser, export of alkaline produce from farmlands and other processes were not considered by previous biogeochemical reviews. However, several very recent research studies showing CO2 emissions from soil during nitrifica-tion are consistent with our hypothesis. Despite counter measures to curb excessive CO2 emissions, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address these causes. We recommend that this hypothesis be further tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions de-scribed in this article. Corrective counter measures can then be designed and applied.

The metrological performance of FBG strain sensing systems is a critical premise for the precision of plastics water support pipeline structural deformation measurement, but the strain transfer loss of FBG attached on the plastics pipe subjected by dynamic force is unclear. This paper presents the first study on the effects of strain transfer between FBG, and acrylate polymer blended with poly resin (ABR)pipe sheets loaded by static and dynamic force. Theoretical methods of dynamic strain transfer theory combine with the exponentially decaying sinusoidal shock force time course is deduced and various dynamic parameters sensitivities studies are carried out, as well as that of the geometric parameters. The result of the dynamic theory is compared with the calibration test outcomes, while the ASTR of FBG attached on ABR sheet is compared with distributed optical fiber sensors (DOFS) and other pipe materials such as PVC, concrete, and steel. Results show that the ASTR of FBG is more accurate than that of the DOFS, and the grows of ASTR depending on the paste length of FBG, the Young's modulus of the middle materials, the thickness of the middle materials and attenuation coefficient. Paste length produced the largest increase, yet the magnitude and loading speed of the external force has unexpectedly little effect on ASTR. FBG seem low error, insensitive with dynamic force and independent with the material of matrix, and this demonstrates benefits that are stronger across the board than DOFS. This is not currently recognized by standards or by most reported studies.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Background: Previous neuroimaging studies have identified brain regions related to respiratory motor control and perception. However, little is known about the resting-state functional connectivity (FC) associated with respiratory impairment. We aimed to determine the FC involved in mild respiratory impairment without changing the saturation of percutaneous oxygen. Methods: We obtained resting-state functional magnetic resonance imaging data from 36 healthy volunteers during normal respiration and mild respiratory impairment induced by resistive load (effort breathing). ROI-to-ROI and seed-to-voxel analyses were performed using Statistical Parametric Mapping 12 and the CONN toolbox. Results: Compared to normal respiration, effort breathing activated FCs within and between the sensory perceptive area of respiration (the postcentral gyrus, anterior insular cortex (AInsula), and anterior cingulate cortex) and visual cortex (the visual occipital, occipital pole (OP), and occipital fusiform gyrus). Graph theoretical analysis showed strong centrality in the visual cortex. A significant positive correlation was observed between the dyspnoea score (modified Borg scale) and FC between the left AInsula and right OP. Conclusions: These results suggested that the FCs within the respiratory sensory area via the network hub may be neural mechanisms underlying effort breathing and modified Borg scale scores.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Spacecraft recovery technology is crucial in the field of aerospace, in which the parachute plays a key role in slowing down the descent speed of the spacecraft and realizing a smooth landing. In order to construct a dynamically adjustable parachute deployment strategy, it is necessary to measure the parachute dynamic load accurately in real time. However, the existing sensor measurement scheme is difficult to meet the measurement requirements due to its large structure and complex wiring. In order to meet the current demand for real-time measurement of parachute cords dynamic load, a miniature measuring instrument is designed.According to the function and technical requirements of the miniature measuring instrument, the hardware modules of the acquisition system are selected and designed, and the integration debugging and performance optimization of the microcontroller module, A/D sampling module, signal acquisition circuit and power supply module are carried out. The software of the parachute cords tension acquisition system based on the miniature measuring instrument is developed. The elastomer is modeled by using SolidWorks and statically analyzed by using AnsysWorkbench finite element analysis software. Then the final structure of the elastomer and the pasting position of the strain gage are determined through the results analysis as well as experimental verification. The hardware module of the signal acquisition system for the miniature measuring instrument is then encapsulated. The force value of the miniature measuring instrument is calibrated and tested many times by using the microcomputer-controlled electronic universal testing machine. The experimental results show that the designed miniature measuring instrument has accurate data, strong stability and good real-time performance, which meets the demand for real-time accurate measurement of miniature measuring instrument, and can provide reliable data for parachute cords parameter validation and stepless unfolding design.

Electricity load forecasting is a crucial undertaking within all the deregulated markets globally. In contemporary times, the transition from conventional electricity grids to Smart Grids constitutes an area where extensive research is conducted on a global scale. Among the research challenges, the investigation of Deep Transfer Learning (DTL) in the field of electricity load forecasting represents a fundamental effort that imparts generality to Artificial Intelligence applications, due to new capabilities, such as knowledge transfer and computational power reduction. In this paper a comprehensive study is conducted for day-ahead electricity load forecasting. For this purpose, three Sequence-to-Sequence (Seq2seq) Deep Learning (DL) models are used, namely the Multilayer Perceptron (MLP), the Convolutional Neural Network (CNN) and the Ensemble Learning Model (ELM), which is consisted of the weighted combination of the outputs of MLP and CNN models. Also, the study focuses on the development of different forecasting strategies based on DTL and emphasizing the way the datasets are trained and fine-tuning for higher forecasting accuracy. In order to implement the forecasting strategies using Deep Learning models, load datasets from three Greek islands, Rhodes, Lesvos, and Chios, are used. The main purpose is to apply DTL for day-ahead predictions (1-24 hours) for each month of the year for Chios dataset after training and fine-tuning the models using the datasets of the three islands in various combinations. After several trials, four DTL strategies are illustrated. In the first strategy (DTL Case 1), each of the three DL models is trained using only Lesvos dataset, while fine-tuning is performed on the dataset of Chios island, in order to create day-ahead predictions for Chios load. In the second strategy (DTL Case 2), data from both Lesvos and Rhodes concurrently are used for the DL model training period, and fine-tuning is performed on the data from Chios. The third DTL strategy (DTL Case 3) contains the training of the DL models using Lesvos dataset, and the testing period performed directly on the Chios dataset without fine-tuning. The fourth strategy is a Multi-task Deep Learning (MTDL) approach, which has been extensively studied in recent years. In MTDL, the three DL models are trained simultaneously on all three datasets and the final predictions are made on the unknown part of the dataset of Chios. In this paper, we explore the performance of DTL and compare the results with those produced with MTDL. The results demonstrated that DTL can be applied with high efficiency for day-ahead load forecasting. Specifically, the two cases with fine-tuning (DTL Case 1 and 2) outperformed MTDL in terms of load prediction accuracy. Regarding the DL models, all three exhibit very high prediction accuracy, especially in the two cases with fine-tuning. The ELM excels compared to the single models. More specifically, for conducting day-ahead predictions, it has been concluded that the MLP model presents best monthly forecasts with a MAPE of 6.24% and 6.01% for the first two cases, the CNN model presents best monthly forecasts with a MAPE of 5.57% and 5.60% respectively and the ELM model achieves best monthly forecasts with a MAPE of 5.29% and 5.31%, respectively, indicating the very high accuracy it can achieve.

Background: Oxidative stress has emerged as a key contributor to numerous NCDs (Non Communicable Diseases), including cardiovascular diseases, cancer, and diabetes. This study aims to explore the potential of targeted interventions to mitigate oxidative stress as part of a primary prevention strategy. Methods: The study included 32 healthy participants (11 men, 21 women) aged 45-65 who completed both the initial and follow-up assessments of the Healthy Days Initiative, a community-based wellness program organized by the non-profit Associazione O.R.A. ETS. Through blood analysis, vital sign assessment, lifestyle questionnaires, and individualized recommendations, participants received guidance on improving their health and reducing disease risk. The initiative also offered the opportunity for participants to consume a flavonoid supplement containing quercitrin, rutin and hesperidin, with the goal of reducing oxidative stress. Participants who opted for supplementation were instructed to take 1-2 tablets daily for two weeks. Data collected included demographic information, anthropometric measurements, vital signs, dietary and lifestyle habits, medical history, WHO-5 Well-Being Index scores, and blood parameters. Results: Significant reductions were observed in glucose levels (from 82 to 74.5 mg/dL), reactive oxygen metabolites (d-ROMs) (from 394.5 to 365.5 U.CARR), and systolic blood pressure (from 133 to 122 mmHg) after the two-week flavonoid intervention. Most participants (26/31) reported no side effects, and the majority (30/31) expressed a willingness to continue using a product combination of quercitrin, rutin and hesperidin or a similar product long-term. Conclusions: While limited in scope and duration, the PREVES-FLAVON study contributes valuable insights to the growing body of evidence suggesting that flavonoid supplementation may play a significant role in reducing risk factors associated with NCDs in primary prevention settings. By targeting novel risk factors such as oxidative stress, this intervention holds promise for mitigating the global burden of NCDs and promoting healthy aging.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

Mechanical properties of cardiomyocytes from different transmural regions are heterogeneous in the left ventricular wall. The cardiomyocyte mechanical environment affects this heterogeneity because of mechano-electric feedback mechanisms. In the present study, we investigated the effects of load upon transmural differences in contraction of subendocardial (ENDO) and subepicardial (EPI) single cells isolated from the murine left ventricle. Various loads were applied to the cells using carbon fiber techniques for single myocytes. To simulate experimentally obtained results and to predict mechanisms underlying the cellular response to change in load, our mathematical models of the ENDO and EPI cells were used. Extent of the transmural gradient in the time course of contractions was independent of the loading conditions where unloaded and heavy loaded (isometric) contractions were examined, but the regional gradient of the relaxation time characteristics tended to decrease when the load decreased. Under auxotonic contractions, time to peak contraction (T_max) was significantly longer in ENDO cells than in EPI cells at low preload. An increase in preload (axial stretch) prolonged T_max in both cell types; however, the prolongation was greater in EPI cells, resulting in a decrease in transmural gradient in T_max at high preload. The [Ca²⁺]_i transient decay time constant was consistent with the greater preload dependency in T_max of EPI cells. Our modified mathematical models reproduced experimental results, suggesting that differences in cooperativity of cross bridges and calcium troponin C complex interactions between the ENDO and EPI cardiomyocytes may contribute to the different cellular responses to stretch, which may provide a decrease in transmural dispersion of cellular shortening in the intact heart.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

The demonstration of compliance of rolling stock against disturbance limits for railway signaling, and in particular track circuits, is subject to a large deal of variability, caused by the diverse values of the electrical parameters of the railway line and resulting transfer functions, as well as operating conditions of rolling stock during tests. Instrumental uncertainty is evaluated with a Type B approach and shown to be much less than the experimental variability. Repeated test runs in acceleration, coasting, cruising, braking conditions are considered, deriving both max-hold (spread) and sample dispersion curves compared to the respective mean values (Type A approach to the evaluation of uncertainty). The major source of variability affecting a significant portion of the spectrum is caused by the superposed oscillations of the onboard LC filter, for which different choices of the transformation window duration are discussed. The test runs and the acquired data covered overall 1 day of tests along about 300 km of the Italian 3 kV DC railway network.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Conditional Independence (CI) testing is fundamental in statistical analysis. For example, CI testing helps validate causal graphs or longitudinal data analysis with repeated measures in causal inference. CI testing is difficult, especially when testing involves categorical variables conditioned on a mixture of continuous and categorical variables. Current parametric and non-parametric testing methods designed for continuous variables and can quickly fall short in the categorical case. This paper presents a computational approach for CI testing for categorical data types, which we call computational conditional independence (CCI) testing. The test procedure is based on permutation and combines machine learning prediction algorithms and Monte Carlo Cross-Validation. We evaluated the approach through simulation studies and assessed the performance against alternative methods; the generalized covariance measure (GCM) test, the kernel conditional independence (KCI) test, and testing with multinomial regression. We find that the computational approach to testing has utility over the alternative methods, and we can achieve better control over type-I-error rates. We hope this work can expand the toolkit for CI testing for practitioners and researchers.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Authors evaluated the relevant literature related to the purging which is the interaction between selection and inbreeding where the population may get rid of its inbreeding load at least partially. The backroad of the relevant theory was given and the available methods were described both based on the conventional quantitative genetic approach (based on genealogy data) and based on the latest genomic methods. The different parameters necessary for signalling purging (highlighting those inbreeding coefficients which are not yet been widely known in animal and veterinary science) were presented together with the relevant results of the literature. The available statistical methods together with the softwares and R packages to calculate various inbreeding coefficients and to determine inbreeding depression and purging were provided. The main results of the different approaches obtained in laboratory ZOO and domesticated populations (lethal equivalents, ancestral inbreeding, Inbreeding-Purging Model, genomic approaches) were summarized and presented. Application possibilities and future prospective of purging was also discussed.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

Undernutrition and micronutrient deficiencies such as anemia are considered significant public health challenges in Bangladesh, which enhancing fish consumption is a well-established food-based intervention to address these. This paper documents the establishment of community-based fish chutney production and reports the impact of its consumption on mid-upper arm circumference (MUAC) and hemoglobin (Hb) levels among targeted 150 pregnant and lactating women (PLW) in rural Bangladesh. A fish chutney was developed using locally available ingredients followed by a series of laboratory tests, including nutrient composition, shelf-life and food safety. A community-based fish chutney production process was designed to: 1) supply locally available ingredients for processing; 2) establish two fish drying sites; 3) initiate a community-based production site, and 4) distribute fish chutney to PLW by six women nutrition field facilitators for one year. Then a pre- and post-intervention study was designed for a selected 150 PLW to receive 30g of fish chutney daily for 12 months. Differences in mean mid-upper arm circumference (MUAC) and hemoglobin (Hb) levels pre- and post-consumption were analyzed using one-way analysis of variance. Consumption of 30g of fish-chutney resulted in significant increases of the mean values of Hb levels and MUAC among the targeted PLW.

Background: The skin prick test (SPT) is used to diagnose sensitization to antigens. This study proposes a deep learning approach to infer wheal dimensions, aiming to reduce dependence on human interpretation. Methods: A dataset of SPT images (n=5844) was used to infer a convolutional neural network for wheal segmentation (ML model). Three methods for inferring wheal dimensions were evaluated: the ML model; the standard protocol (MA1); and approximation of the area as an ellipse using diameters measured by an allergist (MA2). The results were compared with assisted image segmentation (AIS), the most accurate method. Bland-Altman, distribution analyses, and correlation tests were applied to compare the methods. The study also compared the percentage deviation among these methods in determining the area of wheals with regular geometric shapes (n = 150) and with irregular shapes (n=150). Results: The Bland-Altman analysis showed that the difference between methods was not correlated with the absolute area. The ML model achieved a segmentation accuracy of 85.88% and a strong correlation with the AIS method (ρ=0.88), outperforming all other methods. Additionally, MA1 showed significant error (13.44±13.95%) for pseudopods. Conclusions: The ML protocol can potentially automate the reading of SPT, offering greater accuracy than the standard protocol.

Iron plays a critical role in lung infections due to its function in the inflammatory immune response but also as an important factor for bacterial growth. Iron chelation represents a potential therapeutic approach to inhibit bacterial growth and pathologically increased pro-inflammatory mediator production. The present study was designed to investigate the impact of the iron chelator, DIBI, in murine lung infection induced by intratracheal Pseudomonas aeruginosa (strain PA14) administration. DIBI (80mg/kg) was given by intraperitoneal injection either as a single dose immediately after PA14 administration or a double dose (second dose 4 h after PA14 administration). The results showed that lung NF-κBp65 levels, as well as levels of various inflammatory cytokines (TNFα, IL-1β, IL-6) both in lung tissue and bronchoalveolar lavage fluid (BALF), were significantly increased 24h after PA14 administration. Single-dose DIBI did not affect the bacterial load or inflammatory response in the lungs or BALF. However, two doses of DIBI significantly decreased bacterial load, attenuated NF-κBp65 upregulation, reduced inflammatory cytokines production, and relieved lung tissue damage. Our findings support the conclusion that the iron chelator, DIBI, can reduce lung injury induced by P. aeruginosa, via its anti-bacterial and anti-inflammatory effects.

The optimal combination of five components to develop a concrete for high-temperature applications was studied through a response surface methodology known as mixture design of experiment. The selected components were water, an alkali-activated binder based on ferronickel slag activated with potassium silicate and potassium hydroxide, and three aggregate sizes corresponding to 0-4 mm, 4-8 mm, and 8-16 mm. Selected response parameters were slump and compressive strength before and after heat exposure. Six cubes of side 150 mm were cast for each concrete mix, three for ambient and three for residual (post-heat exposure) compressive strength. All 20 concrete mixes were exposed to a thermal load of 600 °C for two hours. The optimal concrete mix was adapted for large-scale applications, by increasing slump and replacing limestone with olivine aggregates for enhanced residual compressive strength. The adapted mix resulted in concrete with 76 MPa and 32 MPa compressive strength before and after high-temperature exposure. The CO2 emissions were found to be 77 % lower when compared to traditional OPC concrete.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

: Leveraging the sustainability of the power system market, researchers have developed various ML models for forecasting electricity demand. The LSSVM is well suited to handle complex non-linear power load series. However, the less optimal regularization parameter and the Gaussian kernel function in the LSSVM model have contributed to flawed forecasting accuracy and random generalization ability. Thus, these parameters of LSSVM need to be chosen appropriately using intelligent optimization algorithms. This study proposes a hybrid model based on the LSSVM optimized by the IBFOA for forecasting the daily electricity load in Peninsular Malaysia. The IBFOA for parameter optimization of LSSVM is introduced. The IBFOA based on the sine cosine equation is proposed to adjust the constant step size in the BFOA, which creates an imbalance between the exploration and exploitation during optimization. Finally, the load forecasting model based on LSSVM-IBFOA is constructed using MAPE as the objective function. Comparative analysis demonstrates the model, achieving the highest R2 (0.9880) and significantly reducing error metrics (MAPE, MAE, RMSE, MSE, NRMSE) compared to the baseline LSSVM (average reduction of 27.72% to 47.72%). Additionally, IBFOA exhibits faster convergence and higher accuracy compared to BFOA, highlighting the accuracy of LSSVM-IBFOA for short-term load forecasting.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

Cardiac autonomic neuropathy (CAN) is a severe complication of diabetes mellitus (DM) strongly linked to a nearly five-fold higher risk of cardiovascular mortality. Patients with Type 2 Diabetes Mellitus (T2DM) are a significant cohort in which these assessments have particular relevance to the increased cardiovascular risk inherent in the condition. This study aimed to explore the subtle correlation between the Ewing test, Sudoscan-cardiovascular autonomic neuropathy score, and cardiovascular risk calculated using SCORE 2 Diabetes in individuals with T2DM. The cohort consisted of 211 patients diagnosed with T2DM with overweight or obesity without established ASCVD, aged between 40 to 69 years. The prevalence of CAN in our group was 67.2%. In the study group, according SCORE2-Diabetes, four patients (1.9%) were classified with moderate cardiovascular risk, thirty-five (16.6%) with high risk, and one hundred seventy-two (81.5%) with very high cardiovascular risk. On multiple linear regression, the SCORE2-Diabetes algorithm remained significantly associated with Sudoscan CAN-score and Sudoscan Nephro-score and Ewing test score. Testing for the diagnosis of CAN in very high-risk patients should be performed because approximately 70% of them associate CAN. Increased cardiovascular risk is associated with sudomotor damage and that Sudoscan is an effective and non-invasive measure of identifying such risk.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

This article raise a topic of critical examination of polypropylene, a key polymeric material, and its extensive application within the automotive industry, particularly focusing on the manufacturing of brake fluid reservoirs. The study aims to enhance the understanding of polypropylene's behavior under mechanical stresses through a series of laboratory destruction tests and numerical simulations, emphasizing the Finite Element Method (FEM). A novel aspect of this research is the introduction of the PEAK parameter, a groundbreaking approach designed to assess the material's resilience against varying states of strain, known as triaxiality. This parameter facilitates the identification of critical areas prone to crack initiation, thereby enabling the optimization of component design with a minimized safety margin, which is crucial for cost-effective production. The methodology involves conducting burst tests to locate crack initiation sites, followed by FEM simulations to determine the PEAK threshold value for the Sabic 83MF10 polypropylene material. The study successfully validates the predictive capability of the PEAK parameter, demonstrating a high correlation between simulated results and actual laboratory tests. This validation underscores the potential of the PEAK parameter as a predictive tool for enhancing the reliability and safety of polypropylene automotive components. The research presented in this article contributes significantly to the field of material science and engineering by providing a deeper insight into the mechanical behavior of polypropylene and introducing an effective tool for predicting crack initiation in automotive components. The findings hold promise for advancing the design and manufacturing processes in the automotive industry, with potential applications extending to other sectors.

Monitoring the integrity of aeronautical structures is fundamental for safety. Structural Health Monitoring Systems (SHMS) perform real-time monitoring functions, but their performances must be carefully assessed. In this work the damage detection performances of a strain-based SHMS, were evaluated on a composite helicopter rotor blade root. The SHMS monitored the bonding between the central core and the surrounding antitorsional layer. A damage detection algorithm was trained through Finite Element analyses performed on the component. The effects of the loads variability and of damages were decoupled by including a load recognition step in the algorithm. Load recognition was accomplished in different ways: version#1 adopted an Artificial Neural Network (ANN) trained on blades in pristine condition; version#2 was trained also on damaged blades; version#3 adopted a calibration matrix method. Anomaly detection, damage assessment, and localization were performed by using an ANN. Results showed a higher load identification and anomaly detection accuracy for version#1 and version#2 compared to version#3. Gaussian noise reduced anomaly detection and damage assessment performances, and reduced damage localization accuracy for bigger damages. The damage detection performance were obtained for a fibre optic based-SHMS, including the trade-off between probability of detection and false alarm rate for different damage sizes.

There has been significant increase of studies investigating plasma biomarkers of Alzheimer’s and their relationship to cognitive functioning. The impact of ethnicity on this relationship has not been extensively studied. The current research investigated the relationship between the plasma biomarkers of total tau, Aβ40, Aβ42 and NfL and neuropsychological test performance in a bi-ethnic sample of cognitively unimpaired, older community dwelling adults. The 1326 cognitively unimpaired participants drawn from The Health & Aging Brain Study – Health Disparities (HABS-HD) study included 765 Mexican American participants and 860 non-Hispanic White participants with complete plasma biomarkers and neuropsychological testing. Plasma samples were assayed using Simoa technology. Significant differences in concentrations were found for all of the plasma biomarkers. NHWs had significantly higher levels of each of the biomarkers with a lower Aβ42/ Aβ40. With none of the biomarkers related to performance on any of the neuropsychological tests. For MAs, Aβ40 was the only biomarker that was significantly related to neuropsychological test performance. Aβ40 levels were negatively related to performance on Trails A, Trails B and Digit Symbol Substitution. Results suggest that the relationship of these biomarkers to cognitive functioning is impacted by ethnicity and may be domain specific.

Wind turbine upgrades have been spreading in the recent years in the wind energy industry, with the aim of optimizing the efficiency of wind kinetic energy conversion. This kind of interventions has material and labor costs and it is therefore fundamental to estimate realistically the production improvement. Further, the retrofitting of wind turbines sited in harsh environments might exacerbate the stressing conditions to which wind turbines are subjected and consequently might affect the residue lifetime. This work deals with a case of retrofitting: the testing ground is a multi-megawatt wind turbine from a wind farm sited in a very complex terrain. The blades have been optimized by installing vortex generators and passive flow control devices. The complexity of this test case, dictated by the environment and by the features of the data set at disposal, inspires the formulation of a general method for estimating production upgrades, based on multivariate linear modeling of the power output of the upgraded wind turbine. The method is a distinctive part of the outcome of this work because it is generalizable to the study of whatever wind turbine upgrade and it is adaptable to the features of the data sets at disposal. In particular, applying this model to the test case of interest, it arises that the upgrade increases the annual energy production of the wind turbine of an amount of the order of the 2%. This quantity is of the same order of magnitude, albeit non-negligibly lower, than the estimate based on the assumption of ideal wind conditions. Therefore, it arises that complex wind conditions might affect the efficiency of wind turbine upgrades and it is therefore important to estimate their impact using data from wind turbines operating in the real environment of interest.

Using the data of China's A-share non-financial listed enterprises from 2015 to 2022 as a sample, this study empirically tests the impact of ESG rating disagreement on corporate debt financing cost. The results show that ESG rating disagreement significantly increases the debt financing costs of enterprises, and this result still holds after a series of robustness tests such as replacing the dependent and independent variables and PSM approach. Meanwhile, the heterogeneity analysis reveals that non-state-owned enterprises and enterprises in non-heavily polluting industries are more sensitive to ESG ratings disagreement. In addition, mechanism analysis shows that corporate financing constraints mediate the relationship between ESG rating disagreements and debt financing costs. The findings of this study provide important evidence for understanding the impact of ESG rating disagreement on the costs of debt financing, enrich the meaning of ESG rating disagreement, and reveal the significance of unifying ESG rating standards.

Tamil Nadu, a state in southern India, is bereft of any native milch or dual-purpose cattle breed and the state depends chiefly on crossbred cattle for milk production. As most (90 percent) of the milk production in the state was contributed by Jersey crossbred cattle, the genetic evaluation study was intended to assess the milk production traits viz., test-day milk yields (TDMYs), total milk yield (TMY) and 305-day milk yield (305MY) in these crossbred cattle reared under farmers’ rearing environment. Data on monthly TDMYs (TDMY1 to TDMY10) of Jersey crossbred cows (n=81,653) reared by the farmers over 24 years (1999-2022) were collected for evaluation. The influence of non-genetic factors viz., location (agroclimatic zones), period and season of calving, and parity on TDMYs, TMY, and 305MY were assessed, and the variance and covariance components for genetic parameters (heritability and genetic correlation) of the traits were estimated by the method of restricted maximum likelihood (REML) under multivariate animal model and by random regression model (RRM). The overall means of various TDMYs ranged from 4.98 (TDMY10) to 9.95 kg (TDMY2) and, for TMY and 305MY the means were 2480.33 and 2393.71 kg respectively. The heritabilities estimated by animal model for TDMYs were high and ranged from 0.39 ± 0.01 to 0.47 ± 0.01 and were fairly less variable throughout the lactation while the estimates obtained by RRM were medium to high and ranged between 0.28 ± 0.01 and 0.65 ± 0.02 for different days in milk (DIMs). The heritability estimated for TMY and 305MY were 0.48 ± 0.01 and 0.49 ± 0.01 respectively. The estimates of heritability in mid-lactation yields were comparatively little less than those at the beginning and the end of lactation. The high estimates of heritabilities for TDMYs, TMY, and 305MY obtained in the present study offered an ample scope for improving milk production through selective breeding. Genetic correlations between TDMYs estimated by animal model were positive and moderate to high, with a range between 0.47 ± 0.01 and 0.99 ± 0.00. Considerably higher estimates (0.97-0.99) were observed between adjacent TDMYs showing strong genetic associations. By RRM, genetic correlations estimated between DIMs were positive, except for a few estimates and the magnitude of genetic correlation decreased with an increase in the interval between the DIMs. The high genetic correlation observed between the TDMYs in early and mid stages of lactation with TMY and 305MY suggested that these test day yields could be used favorably for the early selection of cows for milk production which facilitates reduction in the generation interval and consequently increase the annual genetic gain for the milk production traits.

As climate is not only a valuable tourism resource but also a factor influencing travel experience, estimating climate change can provide implications to sustainable development of the tourism industry. This study develops Climate Volatility Index (CVI) using GARCH model and estimates the relationship between CVI and Japanese tourism demand for Korea using a tourism demand model, based on data from January 2000 to December 2013. Time lag is applied based on a decision making process regarding travel destinations. The result shows that an increase in volatility of climate change leads to a decrease in tourism demand.

As time continues to advance, the need for robust security threat mitigation has become increasingly vital in software. However, ensuring early effective security threat mitigation requires optimal test data and consistent test case design. It is a constant struggle to maximize test coverage through test data optimization. We conducted explanatory research to maximize test coverage of security requirements as modeled in Structured Misuse Case Description (SMCD) i.e., structured specification of misuse case, so as to improve consistency in optimal test data generation. We specified constraints upon Mal activity in Object Constraint Language (OCL) in order to minimize human dependency and improve consistency in optimal test data generation. It was evident through results that MC/DC generated optimal test data of security threats through SMCD in comparison to the Decision Coverage method thus resulting in designing a significantly lower number of test cases and yet maximizing test coverage of security threats. MC/DC generated test data with n+1, while Decision Coverage generated test data with〖 2〗^n, we, therefore, conclude that MC/DC maximizes test coverage through optimal test data from SMCD in comparison to Decision Coverage.

We provide a comprehensive framework for forecasting five minute load using Gaussian processes with a positive definite kernel specifically designed for load forecasts. Gaussian processes are probabilistic, enabling us to draw samples from a posterior distribution and provide rigorous uncertainty estimates to complement the point forecast, an important benefit for forecast consumers. As part of the modeling process, we discuss various methods for dimension reduction and explore their use in effectively incorporating weather data to the load forecast. We provide guidance for every step of the modeling process, from model construction through optimization and model combination. We provide results on data from the PJMISO for various periods in 2018. The process is transparent, mathematically motivated, and reproducible. The resulting model provides a probability density of five-minute forecasts for 24 hours.

Then the purposes of this study were to compare and correlate the aerobic threshold (TH_aer) and anaerobic threshold (TH_anaer) measured during a new single judo specific incremental test and Treadmill Test for aerobic demand evaluation. Eight well-trained male competitive judo players (24.3±7.9 years; height of 169.3±6.7cm; fat mass of 12.7±3.9%) performed a maximal incremental specific test for judo mimicking the UchiKomi drills and on treadmill in different days. There was difference between specific and general TH_aer (P=0.0006) as well as weak correlation for TH_aer (r=0.32; R²=0.1; P=0.2) and TH_anaer (rs=-0.31; R²=0.1; P=0.12). When correlation was applied with normalized data (percentage of peak load) we observed moderate correlation for TH_aer (r=0.76; R²=0.58; P=0.027), but the same was not observed for TH_anaer. We conclude that there is a need of TH_aer and TH_anaer evaluation through a specific test for Judo.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

The impact of antecedent soil moisture content on soil erosion is a complicated phenomenon, which is still under argument with contradictions in research results. Hence, the objective of this study is to investigate the impact of antecedent soil moisture content to soil loss on clay soil by conducting two-year field experiments under natural rainfall on runoff plots with length of 10 meters, width of 3 meters, and uniform slope of 9%. Volumetric soil moisture sensors were used to log soil moisture changes, and soil moisture readings were used along with rainfall records to quantify the antecedent soil moisture conditions for each rainfall event. Results of this study show duration of the effective erosion event outranks the antecedent volumetric soil moisture content. Field study also suggests that accumulative rain falling within 48 hours (Pp48) prior to an effective erosion event strongly correlated with soil loss per Rainfall-Runoff Erosivity Index (Soil Loss / EI30), particularly when the duration of an effective erosion event is either between 3 ~ 7 hours or 10~ 30 hours. Hence, Pp48 can be considered as an alternative to replace antecedent soil moisture content in RUSLE 2’s cover and management factor.

Floor mats are commonly used to improve the impact sound performance of existing homes, but the actual reduction does not consistently appear depending on the test-bed conditions used to determine it. Therefore, this study evaluated the effects of the environmental conditions of the test-bed on the impact sound reduction performance of different floor mats. The Korean Industrial Standard, KS F 2865, specifies the measurement method in the test room and sets the thickness range of the available target floor structure from bare slab 120 mm to 210 mm. The evaluation method is ∆?, which is the difference in standardized impact sound levels before and after the installation of the floor finishing material. In this study, a total of eight types of floor mats were tested in four different test-beds according to KS F 2865. The impact sources used were tapping, bang machines and a rubber ball to consider both light-weight and heavy-weight impact sounds. The results were derived as impact sound reduction performance for each frequency band and a single number quantity. The results showed that light impact sound had a similar minimum reduction characteristic of at least 38 dB, regardless of the floor structure on which the mat was installed. However, the heavy-weight impact sound showed different tendencies depending on the floor mat and the characteristics of the floor structure of the test-bed when a bang machine and a rubber ball were used. In particular, the reduction by the bang machine showed less than half the tendency of the reduction by the rubber ball, and the tendency of the heavy-weight impact sound to be reduced depending on the floor mat was maintained, but the reduction differed depending on the test bed. The reduction was larger in the box-type test room than in the real-life type test room, and among the box-type test rooms, the one with a thicker bare slab showed a relatively larger reduction. In addition, the reliability of the measurement results was discussed through the correlation analysis between the single number quantities depending on the thickness of the bare slab of the test-beds.

Background: Recent studies have found forward head posture (FHP) to be associated with altered physiology, however, there is a lack of research into whether FHP is associated with altered gait parameters when cognitively challenged. The current study was undertaken to investigate the changes in gait parameters in asymptomatic individuals with FHP when a cognitive dual task is introduced during walking. Methods: Ninety asymptomatic participants were recruited, 45 having FHP defined as having a craniovertebral angle (CVA) < 50, and 45 sex and age-matched controls having normal head posture (NHP) defined as CVA > 55. All participants walked along a 10 meter platform under a control condition (no cognitive load) with 3 consecutive trials while an optical motion-capture system consisting of 8 infrared cameras was used to assess gait kinematics. Secondly, participants were assessed under a dual task cognitive load condition (3 trials while performing simple addition, counting backwards, and answering yes or no questions) to identify the impact on gait kinematics compared to the control condition. Results: Under the single task condition, there were no significant differences for any gait parameter, however, under the dual task condition, 12/13 gait parameters were significantly altered for the FHP group compared to the NHP group (p < .01). A calculation of dual task cost (DTC) percentage showed significant increases in all gait parameters in participants with FHP (p < .02). Correlations between the CVA and gait parameters were not significant for the single task condition, but all gait parameters were correlated to CVA for the dual task condition (p < .01). The correlation between CVA and DTC for all gait variables were also significant (p < .04). Conclusions: This study demonstrates that FHP significantly increases the cognitive cost during walking, highlighting the importance of proper postural alignment for maintaining cognitive function under a dual task condition. Addressing FHP through targeted interventions could improve both physical and cognitive health, enhancing overall well-being and daily functioning.

Background: In the field of brain-computer interfaces, neural decoding plays a crucial role in translating neural signals into meaningful physical actions. These signals are transmitted to processors for decoding via wired or wireless channels, often encountering data loss, commonly referred to as "packet loss." Despite its importance, the impact of different types and degrees of packet loss on neural decoding has yet to be comprehensively studied. Understanding this impact is critical for advancing neural signal processing and data filtering. Methods: This paper addresses this gap by constructing four distinct packet loss models, simulating congestion packet loss, distributed packet loss, and burst packet loss scenarios. Using macaque superior arm-movement decoding experiments, we evaluate the effects of these packet loss types on decoding performance. Results: Our findings reveal that continuous burst packet loss significantly degrades decoding performance at the same packet loss probability, and decoding parameters that are sensitive to data continuity are more heavily impacted by packet loss. Conclusions: This study provides an analysis of the relationship between packet loss and neural decoding results, offering valuable insights for future strategies aimed at preventing and handling packet loss in neural signal acquisition.

State-of-the-art augmented-reality (AR) glasses record their position and orientation in space, enabling measurements and analyses of clinical gait-and-balance tests. This study’s objective was to evaluate concurrent validity and test-retest reliability for common clinical gait-and-balance tests in people with Parkinson’s disease: the Five Times Sit-To-Stand (FTSTS) and Timed Up-and-Go (TUG) tests. Position and orientation data was collected in 22 participants with Parkinson's disease using HoloLens 2 and Magic Leap 2 AR glasses, from which test-completion durations and durations of distinct sub-parts (e.g., sit-to-stand, turning) were derived and compared to reference systems and over test repetitions. Regarding concurrent validity, for both tests an excellent between-systems agreement was found for position and orientation time series and test-completion durations. Between-systems agreement for FTSTS (sub-)durations were all excellent, while TUG turning sub-durations were excellent (turn 1) and moderate (turn 2). Regarding test-retest reliability, the within-system test-retest variation in test-completion times and sub-durations was always much greater than the between-systems variation, implying that these (sub-)durations may be derived interchangeably from AR and reference-system data. In conclusion, AR data are of sufficient quality to evaluate gait and balance in people with Parkinson's disease, with valid quantification of test-completion durations and sub-durations of distinct FTSTS and TUG sub-parts.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The textile sector is responsible for a number of environmental impacts. Due to the in-creasing quantities of textiles, their share is rising and a trend reversal from a linear to a circular textile chain is needed. This article presents the background, methodological approach and results of a participatory textile development model. In the commercial B2B sector, three textile prototypes were developed together with users and trialled over several months in three application areas. Textile development took into account the requirements of fibre regeneration in the product design and focused on innova-tive chemical recycling solutions. The three sustainably aligned textiles were subject-ed to spectroscopic and textile-technological tests. Screening life cycle assessments an-alysed their environmental profile and compared it with reference textiles that are used as standard. Overall, it is clear that the three textiles can match conventional ref-erence textiles in terms of quality and have considerable environmental benefits com-pared to the reference textiles. The user survey did identify concerns about a high arti-ficial fibre content, although a general rejection of recycled fibres was not observed. The results show that a transformation is possible, but must start with the fibre com-position; recycling, on the other hand, is of minor importance.

The change in the value of the breaking energy is discussed here for selected steel grades used in building structures after subjecting the samples made of them to episodes of heating in the steady-state heating regime and then cooling in a simulated fire conditions. These changes were recorded based on the instrumented Charpy impact tests, in relation to the material initial state. The S355J2+N, 1H18N9T steels and also X2CrNiMoN22-5-3 duplex steel were selected for detailed analysis. The fire conditions were modelled experimentally by heating the samples and then keeping them for a specified time at a constant temperature of: 600°C (first series) and 800°C (second series), respectively. Two alternative cooling variants were investigated in the experiment: slow cooling of the samples in the furnace, simulating the natural fire progress, without any external extinguishing action, and cooling them in water mist simulating an extinguishing action by a fire brigade. The temperature of the tested samples was set at the level -20oC and alternatively at the level + 20oC. The conducted analysis is aimed at assessing the risk of sudden, catastrophic fracture of load-bearing structure made of steel degraded as a result of a fire previously occurred with different development scenarios.

Introduction: Biliary Atresia (BA) is a common cause of neonatal cholestatic jaundice which, if recognized and treated early, can be life-saving for the infant. If the liver biopsy suggests the presence of BA, exploratory laparotomy is then carried out to confirm the diagnosis, along with the Kasai procedure to provide drainage to the bile secreted by the liver. The purpose of this study is to get a deep dive into all the various imaging modalities that can diagnose BA more effectively and with absolute certitude, thus helping prevent several children from a grave prognosis.Methodology: For the collection of the data, a search was done by two individuals using PubMed, Google Scholar, and Cochrane Library databases for all relevant literature. Each qualifying paper was evaluated independently by two reviewers. Each article was analyzed for the number of patients, their age, procedure modality, complexity of ethology, and incidence of the pre-decided complications. The statistical software packages RevMan (Review Manager, version 5.3), SPSS (Statistical Package for the Social Sciences, version 20), Google Sheets, and Excel in Stata 14 were used to perform the statistical analyses. The data was obtained and entered into analytic software.Results: A total of 39 studies with 3,679 subjects were selected for the study, out of which 7 studies showed sensitivity above or equal to 95%, and an astounding 14 studies showed specificity above 95%. The value of True Positive (TP) was 1280, that of True Negative (TN) was 1817, that of False Positive (FP) was 239, and that of False Negative (FN) was 343. With a confidence interval of 95%, sensitivity, specificity, and positive predictive values were calculated. The sensitivity of Ultrasonography for Biliary Atresia is 0.79, with a CI of 95% in a range of 0.77 to 0.81. The specificity of Ultrasonography for Biliary Atresia is 0.88, with a CI of 95% in a range of 0.87 to 0.90. Conclusion: Even though several radiological techniques at present help to detect BA, USG of the abdomen proves to be an effective diagnostic and a modest screening test for the detection of BA.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

(1) Background: Hepatitis B virus (HBV) viral load (VL) is useful in determining treatment eligibility, however, due to high costs associated with the test, hepatitis B e antigen (HBeAg) is recommended as a proxy for HBV VL in resource-limited settings. (2) Methods: We used 299 archived plasma samples with hepatitis B surface antigen (HBsAg), HBeAg, and HBV VL (cut-off of 20,000 IU/mL and 200,000 IU/mL) results from people living with human immunodeficiency virus (PLWH). HBeAg and HBV VL results were analyzed to evaluate the use of HBeAg to determine CHB treatment eligibility and qualification of HBV prevention of mother-to-child transmission (PMTCT) prophylaxis for the first time in Botswana. (3) Results: Approximately 70.8% and 87.5% of participants with HBeAg-positive serology had HBV viral loads ≥20,000 IU/mL and 200,000 IU/mL respectively. Using logistic regression, the odds of having a qualifying HBV VL for CHB treatment and PMTCT prophylaxis were respectively 55.5 and 110.4 times higher in participants with positive HBeAg serology indicating a statistically significant association between HBeAg status and HBV VL. (4) Conclusions: HBeAg detection may not always correlate with high HBV VL, warranting further research focusing on this association, and other biomarkers that correlate better with HBV VL.

Power Electronic development determines introduction of nonlinear devices in Electric Power Systems. Introduction of nonlinear devices increase current harmonics in Transmission and Distribution Power Systems. Distribution transformers and feeders increase power losses and their nominal parameters are reduced. Present work introduces a procedure to evaluate maximum permissible load in single phase distribution transformers with massive introduction of a new type of nonlinear load which changes daily demand graphs.

The purpose of this paper is to describe a feature selection algorithm and its application to enhance the accuracy of the reconstruction of phylogenetic trees by improving the efficiency of tree construction. Applying machine learning models for Arabic and Aramaic scripts such as Deep Neural Networks (DNN), Support Vector Machines (SVM) and Random Forests (RF) each model was used to compare the phylogenies. The methodology was utilized with a dataset containing Arabic and Aramaic scripts, demonstrating its relevance in a range of phylogenetic analyses. Results emphasize the essential role of feature selection by DNNs is outperforming other models in terms of Area Under the Curve (AUC) and Equal Error Rate (EER) across various datasets and fold sizes. Additionally, SVM and RF models show important understandings, advantages and limits of each approach within the context of phylogenetic analysis. This method not only simplifies the tree structures but also enhances their Consistency Index. Therefore offering a robust framework for evolutionary studies. The findings highlight the applications of machine learning in phylogenetics suggesting a path toward accurate and efficient evolutionary analyses and adding a deeper understanding of evolutionary relationships.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

This study delves into the intricate interplay of economic growth components, specifically focusing on Consumption and investment in Saudi Arabia from 2000 to 2022. Employing vector error correction models and cointegration techniques, we analyze the short- and long-term dynamics within the relationship of Consumption, investment, and economic growth. Granger causality analysis is also used to discern these pivotal variables' causal connections. Our empirical analysis reveals a persistent long-term cointegration relationship among the variables, underscoring the enduring nature of their interdependency. Furthermore, our findings highlight Consumption and investment's statistically significant positive impact on economic growth. Notably, the short-term analysis unveils a stable model characterized by an annual adjustment to equilibrium of 100%.Moreover, the Granger causality study demonstrates unidirectional causal linkages between Consumption, investment, and economic growth. These findings hold substantial implications for policy formulation in Saudi Arabia. Policymakers must grasp the ramifications of burgeoning prosperity and evolving private consumption patterns on future environmental outcomes. Achieving sustainable long-term results necessitates equal emphasis on bolstering private Consumption and fostering other facets of economic growth.

Upon inbreeding, the architecture of the inbreeding load shifts as selection purges strongly deleterious recessive mutations and drift fixes many milder ones. Most small inbred populations show limited genetic variation while crosses between such populations commonly express pronounced heterosis, confirming fixation. In contrast, purging appears to be limited in that inbred populations often retain substantial inbreeding depression. In addition we have the enigma Darwin noted: purely selfing taxa are unknown. Because both purging and fixation reduce inbreeding depression and load, another mechanism must exist to sustain these. Background selection and the associations that develop among alleles in small inbred populations will shift the architecture of the load potentially creating blocks of recessive mutations linked in repulsion. This would generate pseudo-overdominance that could sustain these “PODs” and inbreeding load. Recombination and crosses between lineages could erode PODs. Crosses between populations fixed for different mutations would generate high pseudo-overdominance, enhancing heterosis and potentially POD formation. New recessive mutations arising within PODs would reinforce overdominance. PODs should generate clear genetic signatures including genomic hotspots of heterozygosity and linkage disequilibrium containing alleles at intermediate frequency generating segregating load. Results from several simulation and empirical studies match these predictions. Further simulations and comparative genomic analyses are needed to rigorously test whether PODs exist in sufficient strength and number to generate persistent inbreeding depression and load in inbred lineages.

The Geopyörä breakage test uses two counter-rotating wheels to nip and crush rock specimens with a tightly controlled gap between rollers. The force applied and energy consumed during breakage are measured with instrumentation. In contrast to drop weigh test (DWT) methods, the breakage energy is a response to the rock compressive strength and degree of compression, not a controlled test input, such as the kinetic input energy of a falling weight. This paper presents the detailed measures conducted to evaluate the accuracy and precision of energy measurements across various ore types using the Geopyörä device. While force measurement was assessed just for its precision. The outputs are compared directly to the DWT measures of fragmentation at the same energy and fitted A and b parameters. The test reproducibility was evaluated using a Round-Robin methodology, testing several samples in multiple laboratories. The results confirmed that the new test has sufficient accuracy to match DWT results and excellent precision to assure reproducibility.

We develop a primality test for Mersenne numbers and investigate the primality of the sequence of Catalan-Mersenne numbers. We use induction as a proof to show that the 5th Catalan-Mersenne number is a prime number, thus demonstrating the infinitude of Mersenne primes.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

(1) Background: The purpose of this study was to assess the external load demands in futsal, con-sidering both home and away matches and their outcomes, in order to plan microcycles throughout the season based on the external load of each match. (2) Methods: The external load of 10 players from a First Division team in the Spanish Futsal League was recorded. The total dura-tion of player involvement with the clock stopped was 18.15 ±7.04 minutes. The players' external load was monitored using OLIVER devices. To analyse the influence of the match outcome and location on the external load, a univariate general linear model (GLM) analysis was conducted. (3) Results: There are no differences between the variables, except for accelerations of 2 to 3 m/s² (m) per minute and the number of accelerations of 2 to 3 m/s² per minute. Despite not showing significant differences, there is a trend indicating a higher demand for external loads in away matches as well as in matches won. (4) Conclusions: These findings are important for planning microcycles and providing the appropriate dosage to each player to achieve optimal performance in matches.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Deploying Cellular Internet of Things (CIoT) devices in urban and remote areas faces significant energy efficiency challenges. This is especially true for Narrowband IoT (NB-IoT) devices, which are expected to function on a single charge for up to 10 years while transmitting small amounts of data daily. The 3rd Generation Partnership Project (3GPP) has introduced energy-saving mechanisms in Releases 13 to 16, including Early Data Transmission (EDT) and Preconfigured Uplink Resources (PUR). These mechanisms extend battery life and reduce latency by enabling data transmission without an active Radio Resource Control (RRC) connection or Random Access Procedure (RAP). This paper examines these mechanisms using the LENA-NB simulator in the ns-3 environment, which is a comprehensive framework for studying various aspects of NB-IoT. The LENA-NB has been extended with PUR, and our analysis shows that PUR significantly enhances battery life and latency efficiency, particularly in high-density environments. Compared to the default RAP method, PUR reduces energy consumption by more than 2.5 times and increases battery life by 1.6 times. Additionally, PUR achieves latency reductions of 2.5-3.5 times. The improvements with PUR are most notable for packets up to 125 bytes. Our findings highlight PUR’s potential to enable more efficient and effective CIoT deployments across various scenarios. This study represents a detailed analysis of latency and energy consumption in a simulated environment, advancing the understanding of PUR’s benefits.

To enhance the peak-shaving capability of the boiler, a mathematical model of hydrodynamic and wall temperature characteristics for the water-cooled wall of a 1000 MW boiler was established. The attributes pertaining to the mass flow distribution, the temperature of the effluent working fluid, pressure drop, and the thermal distribution across the wall surfaces at 30% of the boiler's maximum continuous rating (BMCR) were meticulously computed and subjected to a thorough analytical review. The findings suggest that, under the operation at 30% BMCR load, there is a substantial equilibrium in the flow distribution across the quartet of walls that constitute the water-cooled wall assembly. The maximum mass flow rate deviations in the helical and vertical sections are 1.95% and 3.47%, respectively, showing small flow deviations and reasonable distribution. The temperature deviation in the helical section is 0.3 °C, reflecting the characteristic low thermal deviation in helical tubes. While the temperature deviation at the outlet of the vertical section is higher, it remains within safe limits. The pressure loss across the water-cooled wall system amounts to 0.4 MPa. The peak wall temperature reaches 337.5°C, remaining within the material's permissible safety limits. In-depth performance analysis ensures the safe operating conditions of the water-cooled wall during low load conditions.

Background: Open AI developed ChatGPT, a language model based on the GPT architecture, designed for text-based communication. Trained on diverse internet texts, ChatGPT generates contextually appropriate responses using machine learning. It understands input through analysis and context interpretation, generating coherent and contextually relevant responses. Interaction is possible through messaging platforms. Materials and Methods: In November 2023, we utilized ChatGPT 3.5, the default version at that time, to answer questions from the Italian National Residency Program Admission Tests (SSMs) of 2021, 2022, and 2023. The questions cover clinical, diagnostic, analytical, therapeutic, and epidemiological scenarios, sometimes accompanied by images. The study compared ChatGPT's answers to the official corrections on the Italian Ministry of University and Research (MUR) website. The scoring method used for evaluation was 1 point for correct answers, 0 points for unanswered questions, and -0.25 points for incorrect answers, reflecting the SSM test scoring system. Results: In summary, ChatGPT was tested with a total of 420 questions, 140 for each test. It achieved an overall accuracy of 80.48%, providing correct answers for 338 questions and incorrect answers for 82 questions. When faced with questions containing both text and images, it answered 55% correctly and 45% incorrectly. The model's performance varied over time, with an 82.14% accuracy rate in 2021 and 2022 (115 correct out of 140) and a 77.14% accuracy rate in 2023 (108 correct out of 140). Applying thisscoring method to the SSM test, ChatGPT would have scored 105 points in 2021 and 2022, and 100 points in 2023. Conclusions: ChatGPT has exhibited above-average performance in the last three SSM tests, highlighting its robust capability to interpret clinical scenarios and offer precise diagnostic and therapeutic guidance. Despite this, some limitations persist, notably the software's inability to interpret non-textual information.

Background: Liver failure profoundly affects the immune system, leading to dysregulation of innate and adaptive immune responses. Body: This review explores the intricate relationship between liver function and immune homeostasis. The role of the liver as a central hub in immune response initiation is elucidated, emphasizing its involvement in hepatic inflammation induction and subsequent systemic inflammation. Cytokines, chemokines, growth factors, and lipid mediators orchestrate these immune processes, serving as both prognostic biomarkers and potential therapeutic targets in liver failure-associated immune dysregulation. Furthermore, the review delves into the mechanisms underlying immunosuppression in liver failure, encompassing alterations in innate immune cell functions such as neutrophils, macrophages, and natural killer cells (NK cells), as well as perturbations in adaptive immune responses mediated by B and T cells. Conclusion: Understanding the immunological consequences of liver failure is crucial for developing targeted therapeutic interventions and improving patient outcomes in liver disease management.

Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

Electricity demand forecasting has been a real challenge for power system scheduling in the different levels of the energy sectors. Various computational intelligence techniques and methodologies have been employed in the electricity market for load forecasting; although, scant evidence is available about the feasibility of each of these methods considering the type of data and other potential factors. This work introduces several scientific, technical rationale behind intelligent forecasting methods, based on the work of previous researchers in the field of energy. The fundamental benefits and main drawbacks of the aforementioned methods are discussed in order to depict the efficiency of each approach in various situations. In the end, a proposed hybrid strategy is represented.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

Abstract Increasing awareness of the potential health risks associated with microplastics (MPs) presence in the environment has led to significant rise in research focused on these particles over the past few years. This review focuses on research on MPs presence and spread, pathways of exposure and toxicological effects on human health and legal framework related to MP challenges. Several research projects have aimed to assess their potential harm to human health. Toxicological effects have been noticed at high concentrations of MPs, specifically polystyrene, the most widespread typical MP, but only short-term effects have been mostly studied. Significant quantities of consumed MP have been discovered to have diverse detrimental effects, posing a threat to human welfare. The exact concentrations of microplastics that are inhaled and swallowed and then build up in the human body are still not known. Further investigation is necessary to evaluate the impact of MP contamination at minimal concentrations and for prolonged durations.