Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

This study examines the effect of a hyaluronic acid (HyAc) containing tricalcium phosphate putty scaffold material (TCP-P) and of a particulate tricalcium phosphate (TCP-G) graft on bone formation, volume stability and osteogenic marker expression in biopsies sampled 6 months after bilateral sinus floor augmentation (SFA) in 7 patients applying a split-mouth design. Biopsies were processed for immunohistochemical analysis of resin embedded sections. Sections were stained for collagen type I (Col I), alkaline phosphatase (ALP), osteocalcin (OC) and bone sialoprotein (BSP). Furthermore, the bone area and particle area fraction were determined histomorphometrically. Cone-beam CT data recorded after SFA and 6 month later were used for calculating the graft volume at these two time points. TCP-P displayed more advantageous surgical handling properties and a significantly greater bone area fraction and smaller particle area fraction. This was accompanied by significantly greater expression of Col I and BSP and in osteoblasts and osteoid and a less pronounced reduction in grafting volume with TCP-P. SFA using both types of materials resulted in formation of sufficient bone volume for facilitating stable dental implant placement with all dental implants having been in function without any complications for 6 years. Since TCP-P displayed superior surgical handling properties and greater bone formation than TCP-G, without the Hyac hydrogel matrix having any adverse effect on bone formation or graft volume stability, TCP-P can be regarded as excellent grafting material for SFA in a clinical setting.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p < 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (>0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p<0.001), DAPT (p<0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

The type of implant at the fracture site has effects not only from biological perspective but also from mechanical perspective in fracture healing. Biodegradable implants such as magnesium (Mg) based alloys have shown faster secondary bone healing properties as compared to bioinert implants such as titanium (Ti). The general reasoning behind this is the benefit of Mg from biocompatibility perspectives. We study the effect of Ti and Mg as base materials for implants with their different mechanical properties. The focus of our work is on the displacements at the fracture site of the tibia and their influence on the stimulus for bone healing. We have found that in comparison to Ti, Mg implants have minimal stress shielding problem, only which led to better mechanical stimulus at the fracture site.

Shape memory alloys (SMA) are becoming a more important factor in actuation technology. Due to their unique features, they bring the potential to safe weight, installation space and reduce energy consumption. The system integration of the generally small diameter NiTi wires is an important cornerstone for the emerging technology. Crimping, a common method for the mechanical and electrical connection of SMA wires, has several drawbacks when it comes to miniaturization and high force outputs. For high force applications for example, multiple SMA wires in parallel are needed to keep actuation frequencies high, while scaling up the actuation force. To meet these challenges, the proposed study deals with the development of a resistance welding process for manufacturing NiTi wire bundles. The wires are welded to sheet metal substrate, resulting in promising functional properties and high joint strengths. The welding process benefits from low cost, easy to control parameters and good automation potential. A method for evaluating the resistance welding process parameters is presented. With these parameters in place, a manufacturing process for bundled wire actuators is discussed and implemented. The welded joints are examined by peel tests, microscopy, and fatigue experiments. The performance of the manufactured bundle actuators is demonstrated by comparison to a single wire with the same accumulated cross-sectional area.

Can the type of implant rehabilitation influence peri-implant bone loss in case of full-arch mandibular prosthesis? The purpose of the study was to assess, by orthopantomograms (OPG), bone loss around implants in different types of implant-supported prosthetic rehabilitations and evaluate potential risk factors associated with the number and location of implants that may have an association with bone defect. A radiographic study was conducted on 22317 OPGs in the time range from 2010 to 2024. All OPGs with implant-supported prosthetic mandibular rehabilitations were included in the study. A total of 155 OPGs were evaluated, with peri-implant bone loss identified in 64 (41.3%). Distal implants (furthest from the center) across various positioning patterns were most susceptible to bone loss, with positions 3.6 and 4.6 demonstrating the most frequent occurrences (25 and 26 cases, respectively). χ² test revealed significant associations between both implant positioning pattern (p < 0.001) and number of implants (p < 0.001) with peri-implant bone loss. Also by updating the sample of OPGs, increased susceptibility to bone resorption was found for implants placed distal to the mental foramen compared to mesial ones in full-arch implant-supported fixed prostheses. Prospective clinical studies will then be useful to investigate this finding further.

Background/Objectives: Dental implants have become a cornerstone of restorative dentistry, providing a long-lasting method for tooth replacement. The level of osseointegration has a big impact on the biomechanical stability at the bone-implant contact (BIC), which determines how long these implants will work. However, the exact consequences of changing osseointegration levels on different implant designs, especially in bones with variable densities, are not well known. Three short dental implants were tested in this study: BioMet 3iT3, Straumann® Standard Plus Short Regular Neck (SPS-RN), and Straumann® Standard Plus Short-Wide Neck (SPS-WN). 3D finite element analysis (FEA) was used to look at how well they worked biomechanically. This paper tests the implants at four stages of osseointegration: 25%, 50%, 75%, and 100% in both high-density (Bone Type III) and low-density (Bone Type IV) cancellous bone. It also created and examined realistic CAD models under static occlusal loading conditions to assess stress distribution and major strains at the bone-implant contact.; Results: The study discovered that as osteointegration increases, von Mises stress and principal strains go down significantly for all implant types. The SPS-WN implant had the lowest strain values, especially for bone with low density. These reductions demonstrate increased mechanical stability as the bone-implant inter-face becomes more capable of dispersing mechanical stresses, minimizing the potential for localized deformation and bone resorption.; Conclusions: The results highlight the importance of achieving optimum osseointegration to reduce mechanical stress and increase the lifespan of dental implants. The SPS-WN type implant performed better in biomechanical tests than the others, especially when bone conditions were not ideal. This makes it a great choice for clinical applications that need long-term implant success.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

Introduction Cochlear implants are a modern approach for the treatment of multiple cases of profound sensorineural hearing loss. Factors such as the ethiology of hearing loss and the potential for achieving good postoperative outcomes are considered in cochlear implantation. Additionally, surgical strategies, protocols, the experience of the surgeon and audiologist, and the presence of postoperative issues and risks that may require revision surgery should also be taken into account. The surgeon specialized in cochlear implantation must inform the patient and his relatives not only about the surgical technique but also about possible complications. The literature shows different rates of complications evaluated both in adults and in children. An evaluation of adverse events in order to prevent complications can be made if the definition of medical complications and mistakes is strictly approached based on the CLAVIEN-DINDO classification system. The rate of complications can be compared with existing literature. Studies demonstrate the need for preoperative vaccination for pneumococcus, which can prevent complications, especially in patients with inner ear malformations who present an increased postoperative risk Relevant Sections This review is structured around the collection of specialized literature from PubMed, organized into subchapters related to intraoperative complications such as Gusher syndrome, foreign body reaction, endocochlear inflammation phenomena, issues related to electrode positioning and associated complications, vestibular phenomena related to cochlear implantation, as well as late complications related to the surgical wound and cochlear implant extrusion. The important sections in this review are: Inner Ear Malformations and Gusher Syndrome: Intraoperative Complication Risks, Electrode Insertion and Positioning Issues, Intracochlear Inflammation, Foreign Body Reaction, and Intracochlear Fibrosis: Phenomena That Can Occur with Cochlear Implantation, Vestibular Disorders, Tardive Postoperative Complications: Wound Injuries and Cochlear Implant Extrusion and Otitis Media and Cholesteatoma as Complications of Cochlear Implantation Conclusions: Postoperative complications, although considered quite rare. The surgical limits and long-term evolution of cochlear implants cannot be concretely established, despite the fact that this intervention is considered safe in the medium and long term. Future directions Given that cochlear implants represent the most modern surgical technique for auditory rehabilitation in adults and children, with massive implications for quality of life, there is a tendency to extend surgical indications in the future, and especially to inform doctors in related specialties about the benefits of this medical device. Surgeons must be knowledgeable about cochlear implantation methods, as well as the methods for managing complications that can arise immediately postoperatively, as well as in the medium and long term.

Electronic waste generation has been following a continuously rising trend. With electronics containing a myriad of materials some of which are hazardous, toxic, extremely rare or precious combined with more stringent legislative laws which encourage the reuse and optimised recycling of the materials included in e-waste, the need for a holistic approach is inevitable. Such an approach should not only identify the materials found in the various types of e-waste and their respective quantities but also needs to highlight the possible handling techniques and their respective impacts and associated hazards whether to the environment or human health. Performing such a task manually would be exasperating and costly while requiring extensive resources which might not be met with a justifiable economic gain; thus, the use of the advancement in computational sustainability to draw a complete picture and aid in an informed decision-making process is crucial. The e-waste ontology developed in this paper is one way of addressing the problem since it covers the treatment domain, the hazard and the materials contained within the different types of e-waste. The ontology developed can be used directly from the protégé software or by embedding it into a developed Decision Support System.

To evaluate the used and End-of-Life tyre management chains, both direct observation and interviews with approximately 200 used-tyre dealers were conducted. The study revealed that while the used tyre business is well-organized, End-of-Life tyre treatment is nearly non-existent, often involving dumping, open burning for metal recovery, or use in meat processing, causing environmental and health risks. To address these challenges, an 8 t/hr capacity tyre recycling plant is planned, based on estimated tyre availability and development opportunities for sustainable recycling in Togo.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Resonance inductive coupling is widely used for wireless power transfer (WPT) in medical applications. In this paper, we analyze the LCL-compensated WPT structure and propose a novel constant voltage transmission system based on gain estimation, without any extra feedback from the receiver. The system is capable for implant neural stimulation where the load impedance and the coupling coefficient are both variable. Compared to existing methods for constant voltage transmission, our approach offers advantages in compact size and the compatibility with the industrial, scientific and medical (ISM) band. We validate the load-independent resonant characteristic and the feasibility of constant voltage transmission using an experimental prototype working at 6.78MHz. Finally, we discuss the structure of the implant stimulator and methods of applying the proposed WPT system.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

(1) Background : When placing implants in the maxillary posterior region with insufficient alveolar bone, a maxillary sinus elevation is necessary. Autogenous bone, though biologically ideal, poses risks and discomfort due to donor site harvesting. Block-type autogenous tooth bone graft material, made from the patient’s own extracted tooth, offers similar biological stability without these drawbacks; (2) Methods : This study observed the progress of 19 implant patients who were treated with maxillary sinus elevation procedures using block-type autogenous tooth bone graft material at the Daegu Catholic University Medical Center. Extracted teeth were processed into demineralized tooth block bone. After elevating the sinus membrane, implants and the tooth bone graft material were placed in the space, and the bony window was repositioned. Postoperative evaluations through clinical observation and radiographic imaging assessed sinus membrane elevation, alveolar bone height increase, and implant osseointegration; (3) Results : Results showed proportional increases in alveolar bone height to the graft material size, with long-term stability. No postoperative complications occurred, even with sinus membrane perforation, and implants remained stable; (4) Conclusions : The study concludes that maxillary sinus lifts using block-type autogenous tooth bone graft material provide excellent bone induction and biocompatibility, making it a highly beneficial method for both dentists and patients.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Peri-implant infective diseases seem to be the most common cause for the late dental implant failure. Therefore, peri-implant microbiota has been intensively studied in modern implantology. Many studies showed a presence of extremely varied microflora in cases of peri-implant infective diseases. The main scope of this observational single-blind study was to analyze the presence of some microbial species in a group of patients with clinical signs of peri-implant mucositis compared to two other groups (patients treated with dental implants but without any clinical signs of peri-implant inflammation and patients treated with no dental implants). The identification of microorganisms was followed by an antibiogram in order to find their sensitivity to various antibiotics. The results showed a microbiota not necessarily specific for each situation (peri-implant infective diseases, healthy tissues around dental implants and healthy natural teeth and gums) with species like Candida albicans, Neisseria mucosa, Prevotella, Staphylococcus aureus, Streptococcus and others. Peri-implant infective diseases presented more bacterial species than other conditions.

Finite element discretizations of problems in computational physics often rely on hand-generated initial mesh and adaptive mesh refinement (AMR) to preferentially resolve regions containing important features during simulation. We propose Adaptnet, a Graph Neural Networks (GNNs) framework for learning mesh generation and adaptation. The model is composed of two GNNs: the first one, Meshnet, learns mesh parameters commonly used in open-source mesh generators, to generate an initial mesh from a Computer Aid Design (CAD) file; while the second one, Graphnet, learns mesh-based simulations to predict the components of an Hessian-based metric to perform anisotropic mesh adaptation. Our approach is tested on structural (Deforming plate - Linear elasticity) and fluid mechanics (Flow around cylinders - steady-state Stokes) problems. Our results show it can accurately predict the dynamics of the system and adapt the mesh accordingly. The adaptivity of the model supports learning resolution-independent dynamics and can scale to more complex state spaces at test time.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

The imperative to achieve carbon neutrality has driven significant advancements in the construction sector, particularly in the production and utilization of building materials. This paper explores innovative strategies and practices designed to reduce the carbon footprint of construction materials, with a focus on both the production processes and the application of sustainable materials. Key innovations include the development of low-carbon and carbon-negative materials, the integration of renewable energy sources in production, and the implementation of advanced recycling technologies. Case studies of successful projects demonstrate how these strategies can be applied in real-world scenarios, highlighting both the benefits and challenges encountered. The analysis also delves into the technical and economic aspects of these innovations, addressing the barriers to their widespread adoption and proposing solutions to overcome these challenges. Through a comprehensive examination of current practices and future trends, this paper aims to provide a roadmap for the construction industry to achieve carbon neutrality, contributing to broader climate change mitigation efforts and fostering a more sustainable built environment.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

Background and Objectives: This study aimed to evaluate the histological and biochemical ef-fects of capsaicin on implant osseointegration and oxidative stress. Materials and Methods: Male Wistar albino rats weighing between 250 and 300 grams were used in this study. Twenty-four rats were randomly divided into three equal groups: implant + control (n= 8), implant + capsai-cin-1 (n= 8), and implant + capsaicin-2 (n= 8). 2.5 mm diameter and 4 mm length titanium im-plants were surgically integrated into the corticocancellous bone parts of the femurs. In the treatment groups, rats were injected intraperitoneally with 25 mg/kg (implant + capsaicin-1) and 50 mg/kg (implant + capsaicin-2) of capsaicin. No additional applications were made in the con-trol group. Three rats in totally were died during and after the experiment, as a result of the an-alyzes performed on 21 animals. Results: The highest total antioxidant status value was found in capsaicin dose 2, according to the analysis. The control group had the highest total oxidant status and oxidative stress index values, while group 2 of capsaicin had the lowest. After analysis, we found that there was no observed positive effect on osteointegration in this study (p> 0.05), alt-hough the bone implant connection was higher in the groups treated with capsaicin. Conclusi-ons: A positive effect on osteointegration was not observed in this study. This may be due to os-teaclast activation. However it was found that it has a positive effect on oxidative stress. Osteo-clast activation may be the cause of this phenomenon. Capsaicin was found to have a positive effect on oxidative stress (p

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Traditional painting artefacts study and documentation face the limitations of well-known recording tools and methods, such as handwritten or digital descriptions, scaled 2D drawings in situ, measurements with calipers, rulers or tape measures, sketches, tracings, as well as conventional or technical photographs. This paper advocates Close-Range Photogrammetry (SfM-MVS) and Reflectance Transformation Imaging (RTI) for recording vital morphological and 2.5D geometric features of painted surfaces with high accuracy. These digital tools, widely accessible due to increased computing power, enhance art observation, material study and conservation assessment. Despite specialized alternatives like 3D laser scanners, the focus here is on the cost-effective SfM-MVS and RTI, which offer advanced pixel colour accuracy. The ability to reproduce photorealistic textures proves essential for accurate documentation of painted artefacts. The paper showcases promising results from applying these methods to a mural from the Palace of Tiryns, justifying their fundamental role in an integrated scientific art study methodology.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Transcatheter aortic valve implantation (TAVI) has grown exponentially within the cardiology and cardiac surgical spheres. It has now become a routine approach for treating aortic stenosis. Several uncertainties have been raised about TAVI in comparison to conventional surgical aortic valve replacement (SAVR). The primary concerns are with regards to the longevity of the valves. Several factors have been identified that may predict poor outcomes following TAVI. These include the lesser-used finite element analysis (FEA) to quantify the properties of calcifications that affect TAVI valves. This can also be used in conjunction with other integrated software to ascertain the functionality of these valves. Other imaging modalities are now widely available such as Multi-detector row computed tomography(MDCT) which can accurately size the aortic valve annulus.. This may help reduce the incidence of paravalvular leaks and regurgitation which may necessitate further intervention. Structural valve degeneration (SVD) remains a key factor with varying results from current studies. The true incidence of SVD in TAVI compared to SAVR remains unclear with the lack of long term data. It is now widely accepted that both are part of the armamentarium and are not mutually exclusive. Decision-making for the appropriate intervention should be made via shared decision-making involving the heart team.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

Although the connection of implant abutments to implant analogs and implant bodies has been evaluated separately, comparative evaluation of connections to implant analogs and implant bodies has not been evaluated. The objective of this study was to identify whether torque applied during laboratory manufacturing and during restoration cementation affects the compatibility between the implant body-abutment and the implant analog-abutment, as well as to spot any structural differences. Three different implant system with internal conical connection (Bioinfinity, Dant, and Dentist) were used. For each group, straight abutments (n=20) were tightened to implant analogs (n=10) and implant bodies (n=10) with hand tightening and using torque wrench device. The fitting of componenets were evaluated for each group using linear and volumetric micro-CT analysis. For linear analysis, when the mean differences (difference between measurements of the linear distance of abutments during hand tightening and applying torque) values between implant analog and implant body were compared within groups, There was no statistically significant difference observed in all groups (p&gt; 0.05). Throughout the fabrication and clinical phases, it is recommended to tighten the abutments on the analogs with a torque wrench instrument to minimize the risk of prosthetic incompatibility.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Microplastics (MPs) are a critical environmental issue, with impacts ranging from ecosystem contamination to health risks through bioaccumulation. This review addresses the inefficacy of traditional water treatments in removing MPs and proposes photodegradation, particularly via nanomaterial-enhanced photocatalysts, as a solution. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalysts modification to improve photocatalytic performance are thoroughly summarized, with the particular emphasis on element doping and heterojunction construction. Furthermore, this review thoroughly summarizes the possible fundamental mechanisms driving photodegradation of microplastics facilitated by nanomaterials, with a focus on processes like free radical formation and singlet oxygen oxidation. By clearly elucidating these strategies and mechanisms, this review aims to provide valuable insights and inspire further progress in microplastic photodegradation.

Abstract: With a resurgence in ITRT (Immediate Tooth Replacement Therapy) as a method of preserving both hard and thus soft tissues for improved aesthetic outcomes, this multi-centre, retrospective study will look at two novel products and their effect on these outcomes. A new synthetic particulate graft material along with a novel Implant design was utilized in the study and a 1 year follow up assessment, analysed for hard and soft tissue regeneration.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p&lt;0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p&lt;0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

Background: Cochlear implantation is an efficient treatment for postlingually deafened adults who do not benefit sufficiently from acoustic amplification. Implantation is indicated when it can be foreseen that speech recognition with a cochlear implant (CI) is superior to that with a hearing aid. Especially for subjects with residual speech recognition it is desirable to predict CI outcome on the basis of preoperative audiological tests. Purpose: The purpose of the study was to extend and to refine a previously developed model for CI outcome prediction for subjects with preoperative word recognition to include subjects with no residual hearing by incorporat-ing additional results of routine examinations. Results: By introducing the duration of unaided hearing loss (DuHL) the median absolute error (MAE) of the prediction was reduced. While for subjects with preoperative speech recognition the model modification did not change the MAE, for subjects with no residual speech recognition before surgery, the MAE decreased from 23.7% with the previous model to 17.2% with the extended model. Conclusions: Prediction of word recognition with CI is possible within clinically relevant limits. Outcome prediction is particu-larly important for preoperative counselling and in CI aftercare, to support systematic monitor-ing of CI fitting.

(1) Background: This study aimed to compare the effect of polyetheretherketone (PEEK) and titanium abutments on implant prosthetic systems and supporting bone using three-dimensional finite element analysis (FEA); (2) Methods: A three-dimensional finite element analysis was conducted using CATIA and Abaqus software to model mandibular first molar implant systems with titanium and PEEK abutments. Under external loading conditions, finite element analysis was conducted for the stresses in implant components and surrounding bones of each group; (3) Results: The implant fixture of the PEEK model exhibited the highest von Mises stress (VMS). The lowest VMS was observed in the abutment screw of the titanium model. Both implant systems demonstrated similar stress distribution and magnitudes in cortical and cancellous bones; (4) Conclusion: PEEK abutments show similar stress distribution in surrounding bone compared to titanium. However, PEEK absorbs the stresses within the implant system and exhibits the highest VMS values due to its low mechanical and physical properties. Therefore, PEEK abutments need improved mechanical properties for better clinical application.

Keywords: Artificial Intelligence in Implantology; AI in Dental Implantology; Machine Learning in Dental Implantology; Deep Learning in Implant Dentistry; Robotics in Dental Implantology; AI-Based Implant Planning.

Porous structured metallic implants are preferable as bone graft substitutes due to their faster tissue integration mediated by bone in-growth and vascularization. The porous scaffolds/ implants should also mimic the graded structure of natural bone to ensure a match of mechanical properties. This article presents a method to design graded porous structured acetabular implant and identifies the suitable parameters for manufacturing the model through additive manufacturing. The design method is based on slice-wise modification to ensure continuity of gradation. Modification of the slices was achieved through the binary image processing route. A geodesic dome type design was adopted for developing the acetabular cup model from the graded porous structure. The model had a solid shell with the target porosity and pore size gradually changing from 65% and 950 µm, respectively, in the inner side to 75% and 650 µm, respectively, towards the periphery. The required dimensions of the unit structures, and the combinations of pore structure and strut diameter to obtain the target porosity and pore size were determined analytically. Suitable process parameters were identified to manufacture the model by Direct Metal Laser Sintering (DMLS) using Ti6Al4V powder after carrying out a detailed experimental study to minimize the variation of surface roughness and warping over different build angles of the strut structures. A dual contour scanning was implemented to simplify the scan strategy. The minimum diameter of struts that could be manufactured using the selected scanning strategy and scanning parameters was found to be 375 µm. Finally, the model was built and from the micro-CT data, the porosities and pore sizes were found to be closely conforming to the designed values. The stiffness of the structures, as found from compression testing, was also found to be well matching with that of human trabecular bone. Further, the structure exhibited compliant bending-dominated behavior under compressive loading.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

Recent research efforts in bone tissue engineering have been primarily directed towards manufacture-viable synthesis of biomaterials that can significantly enhance the biocompatibilities and osteogenic capabilities on the new biomaterials. This paper presents a straightforward, cost-effective, optimized, and well-controlled hydrothermal synthesis of Nb-doped potassium titanate nanofibers in high-purity. Characterization data revealed that the Nb-doping potassium titanate maintained the crystal structure, showing great promise for applications in bone tissue engineering.

For dental implant treatment to be successful, esthetics, functionality, and cleanability are all required of the superstructure, the final prosthesis. Screw fixation and cementation have been the conventional methods of choice for the crown prosthesis of implants, but these individual methods cannot fulfill all the requirements. As a solution to this problem, we have devised a new implant superstructure restoration method (inlay covering esthetic technique) using computer-aided design / computer-aided manufacturing inlays. This involves the placement of an inlay covering the access hole in a highly translucent partially stabilized zirconia crown. This technique expands the indications for implant treatment and improves the oral quality of life of patients.

An undesirable sensory attribute (“floral taint”) has been recently detected in red wines in some winegrowing jurisdictions in North America (e.g. Ontario, British Columbia, Washington), caused by introduction of frost-killed leaves and petioles [materials-other-than-grapes (MOG)] during mechanical harvest and winemaking. It was hypothesized that terpenes, norisoprenoids, and higher alcohols would be the main responsible compounds. Objectives were to investigate causative volatile compounds for floral taint, and explore threshold concentrations for this problem. Commercial wines displaying varying intensities of floral taints were subjected to GC-MS and sensory analysis. Several odor-active compounds were higher in floral-tainted wines, including terpenes (geraniol, citronellol, cis- and trans-rose oxide), norisoprenoids (β-damascenone, β-ionone), five ethyl esters, and three alcohols. Thereafter, fermentations of Cabernet franc (CF) and Cabernet Sauvignon (CS) (2016, 2017) were conducted. MOG treatments were (wt/wt): 0, 0.5%, 1%, 2% and 5% petioles, and 0, 0.25%, 0.5%, 1%, and 2% leaf blades. Terpenes (linalool, geraniol, nerol, nerolidol, citronellol, citral, cis- and trans-rose oxides, eugenol, myrcene), norisoprenoids (α- and β-ionone), and others (e.g. hexanol, octanol, methyl and ethyl salicylate) increased linearly/quadratically with increasing MOG levels in both cultivars. Principal components analysis separated MOG treatments from the controls with 5% petioles and 2% leaves as extremes. Increasing MOG levels in CF wines increased floral aroma intensity, and were primarily associated with terpenes, higher alcohols, and salicylates. Increased leaf levels in CF were associated with higher vegetal and earthy attributes. Increased petioles in CS were not correlated with floral aromas, but increased leaves increased floral, vegetal and herbaceous attributes. Overall, petioles contributed more to floral taint than leaves through increased terpenes and salicylates (floral notes), while leaves contributed norisoprenoids and C6 alcohols (green notes).

The material properties and structural characteristics of ballistic composites are crucial to their ballistic performance. Investigation for the influence of the material and structural parameters of UHMWPE body armor on anti-fragmentation penetration performance has been made by numerical simulation in this paper, with a numerical modeling simulating the penetration of a 1.1 g FSP into the target plate of UHMWPE body armor, by which the simulation results demonstrate that the failure process of the body armor target plate primarily involves shear damage, interlayer delamination, and tensile damage. Furthermore, the study evaluates the effects of elastic modulus, tensile strength, shear strength, number of layers, and interlayer strength on the ballistic limit velocity of UHMWPE body armor. The findings reveal that the ballistic limit velocity is most sensitive to changes in shear strength, with variation rates ranging from -18.02% to 10.81%, showing an approximate positive correlation, while the elastic modulus has the smallest impact on ballistic limit velocity, with variation rates ranging from -1.8% to 3.6%. Additionally, appropriate interlayer strength can improve the ballistic limit velocity of the body armor to a certain extent. This study provides theoretical methods and recommendations for optimizing anti-penetration performance of UHMWPE body armor.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

Fatigue analysis plays a vital role in determining the structural integrity and life of a dental implant. With the use of such implants on the rise, there is a corresponding increase in the number of implant failures. As such, the aim of this research paper is to investigate the life of 3D-printed dental implants. The dental implants considered in this study were 3D printed according to the direct metal laser sintering (DMLS) method. Additionally, a finite element model was developed to study their performance, while fatigue life was predicted using Fe-Safe software®. The model was validated experimentally by performing fatigue tests. The life of the dental implants was analysed based on Normal strain and the Brown-Miller with Morrow mean correction factor algorithm. The model revealed that there was a strong correlation between the FEA and the experimental results. The clinical success of 3D-printed dental implant experimentally is 20.51 years and computationally under Normal strain is 19.89 years and Brown-Miller with Morrow mean correction factor is 26.82 years.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

This review article deals with the design of bioactive calcium phosphate coatings deposited on metallic substrates to produce bone implants. The bioceramic coating properties are used to create a strong bonding between the bone implants and the surrounding bone tissue. They provide a fast response after implantation and increase the lifespan of the implant in the body environment. The first part of the article describes the different compounds belonging to the calcium phosphate family and their main properties for applications in biomaterials science. The calcium to phosphorus atomic ratio (Ca/P)at. and the solubility (Ks) of these compounds define their behavior in a physiological environment. Hydroxyapatite is the gold standard among calcium phosphate materials, but other chemical compositions/stoichiometries have also been studied for their interesting properties. The second part reviews the most usual deposition processes to produce bioactive calcium phosphate coatings for bone implant applications. Plasma spraying is the main industrial process, but magnetron sputtering, pulsed laser deposition, electrospray deposition, electrophoretic deposition, and electrodeposition are also widely studied in academic and industrial research. The last part describes the main physicochemical properties of calcium phosphate coatings and their impact on the bioactivity of bone implants in a physiological environment.

This study investigates the utilization of innovative green composites made from hemp shiv, a waste by-product of hemp cultivation, with the aim of promoting sustainability within the construction industry. The manufacturing method involve the application of pressure in a mold to create the samples. These materials were produced using an environmentally friendly binder consisting of colophony, arabic gum and corn starch, moreover white glue and bioepoxy are also used to compare with the green resins. Three different binder compositions for the specimens. The samples underwent mechanical testing through tensile and bending assessments, and their performance was compared to that of non-green binders to validate the effectiveness of the manufacturing processes. The study revealed that decreasing the moisture content during the curing process is crucial for improving the mechanical properties. The best results were achieved when using arabic gum as a binder, yielding a tensile strength of 2.16 MPa and a bending strength of 5.25 MPa, with a composition of 62.5% hemp shiv and a manufacturing process involving a pressure of 5 MPa.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

The need to develop novel lightweight materials and their manufacturing processes is sets out to meet the new aerospace, automotive and construction requirements. Within this context, this research work is proposed to develop a novel thermoplastic composite material with high mechanical properties. These composites will be based on thermoplastic matrixes made from polyamide and 35% short glass fiber filled-polyamide reinforced with different types of fabrics. As reinforcement, glass fiber fabrics will be used as the base. They will be treated with different processes, both chemical and physical, to promote adherence to the matrix. Textile overmoulding technology was selected for manufacturing these composites. This technology was primarily developed to manufacture aesthetic lined components and has achieved a great implantation. Once these new composites are manufactured, they will be submitted to different tests to evaluate their behavior regarding adhesion, impact strength and stiffness. It is expected an improvement on stiffness and impact absorption.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p &lt; 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

The present review compared the efficacy of soft tissue substitutes (STS) and autogenous free gingival graft (FGG) or connective tissue graft (CTG) in mucogingival procedures to increase keratinized tissue (KT) width around teeth and implants. Two independent examiners performed the electronic search on Medline and Cochrane Library based on the following PICO’s format: (P) adult patients; (I) soft tissue substitutes and FGG/CTG; (C) STS vs CTG; STS vs FGG; STS vs CTR; (O) KT width gain; (S) Systematic Reviews, Randomized Controlled Trials. Results showed that around teeth, all biomaterials showed superior performance compared to CAF alone for treating gingival recessions. However, when compared to CTG, ADM yields the most similar outcomes to the gold standard (CTG), even though in multiple recessions CTG still continue to be considered the most favorable approach. Use of STSs (acellular matrix or tissue engineered) in combination with an apically positioned flap resulted in a significantly less gain of KTW compared to what achieved with FGG and APF. Around dental implants, free gingival grafts were deemed more effective than soft tissue substitutes in enhancing keratinized mucosa width.

Breast cancer is the most common cancer in women globally, often necessitating mastectomy and subsequent breast reconstruction. Silicone mammary implants (SMIs) play a pivotal role in breast reconstruction, yet their interaction with the host immune system and microbiome remains poorly understood. This study investigates the impact of SMI surface topography on host antimicrobial responses, wound proteome dynamics, and microbial colonization. Biological samples were col-lected from ten human patients undergoing breast reconstruction with SMIs. Mass spectrometry profiles were analyzed for acute and chronic wound proteomes, revealing a nuanced interplay between topography and antimicrobial respondseproteins. 16S rRNA sequencing assessed mi-crobiome dynamics, unveiling topography-specific variations in microbial composition. Surface topography alterations influenced wound proteome composition. Microbiome analysis revealed heightened diversity around rougher SMIs, emphasizing topography-dependent microbial inva-sion. In vitro experiments confirmed staphylococcal adhesion, growth, and biofilm formation on SMI surfaces, with increased texture correlating positively with bacterial colonization. This comprehensive investigation highlights the intricate interplay between SMI topography, wound proteome dynamics, and microbial transmission. The findings contribute to understanding host-microbe interactions on SMI surfaces, essential for optimizing clinical applications and minimizing complications in breast reconstruction.

The clinical application of Phentolamine Mesylate (PM) as an anaesthetic reversal agent has been documented in paediatric patients and in conservative dentistry, but no studies have been found in implant surgery. A prospective randomised study was conducted in 60 patients eligible for mandibular implant treatment, randomly divided between the Control Group (CG) and Experimental Group (EG), who were administered PM. Haemodynamic changes, adverse effects and patient satisfaction were assessed. No statistically significant differences in haemodynamic changes and postoperative pain were found between CG and EG (p&lt;0.05), except for Systolic Blood Pressure (SBP) which increased slightly in EG, without posing a risk to the patient. There were no differences in the presence of adverse effects between the two groups, except in the CG which presented greater difficulty in chewing and biting (p&lt;0.05) and the EG with greater pain in the injection area (p=0.043). 83.3% of the EG patients would request PM again for future dental treatment. The use of PM offers an alternative in implant surgery, without increasing the risks and increasing the patient's quality of life.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

Medical implants made of biodegradable materials could be of advantage for temporary applications such mechanical support during bone-healing or as vascular stents to keep blood vessels open. After completion of the healing process the implant would disappear, avoiding long-term side effects or the need for surgical removal. Various corrodible metal alloys based on magnesium, iron or zinc have been proposed as sturdier and potentially less inflammatory alternative to degradable organic polymers, in particular for load-bearing applications. Despite the recent introduction of magnesium-based screws the remaining hurdles to routine clinical applications are still challenging, such as limiting mechanical material characteristics or unsuitable corrosion characteristics. Here, salient features and clinical prospects of currently investigated biodegradable implant materials are summarized with a main focus on magnesium alloys. A mechanism of action for the stimulation of bone growth due to the exertion of mechanical force by magnesium corrosion products is discussed. To explain divergent in vitro and in vivo effects of magnesium a novel model for bacterial biofilm infections is proposed which predicts crucial consequences antibacterial implant strategies.

The first treatments with dental implants had low success rates (75%). Nowadays, oral rehabilitation with titanium dental implants has a high success rate (95-98%). The success rate significantly increases due to increased scientific knowledge about osseointegration, changes in surgical techniques, and the development of implant surface treatments. Despite the high success rate of implants, no protocol defines the time for the prosthesis to be installed and loaded after surgery. This work compares a new dental implant's primary (mechanical) and secondary (osseointegration) stability. Dental implant with micro- and nano-roughness surface was placed in 24 patients with a minimum of 35 N.cm and a maximum of 60 N.cm. Primary stability was quantified with a torque wrench and Ostell Mentor. The secondary stability 45 and 60 days after surgery was measured with Ostell. The results showed no statistical difference in secondary stability at 45 and 60 days postoperatively among implants. The success rate of dental implants can be associated with the surface morphology with micro and nano-roughness and the shape of the fillets of the implant threads. When the manufacturer's guidelines are followed, it is possible to prosthetically rehabilitate the patient with an implant 45 days after surgery.

Currently the bimatoprost implant (DURYSTA) is approved for a single administration secondary to concern for progressive corneal endothelial cell (CEC) loss with intracameral administration. In order to better understand the cause of CEC loss and other adverse events (AEs) with intracameral administration, multimodal imaging of the implant utilizing optical coherence topography (OCT), robotic ultrasound and bio microscopy video recording was utilized. Inherently the anterior chamber is a non-confined space. In certain examples the implant assumed a round and spotted structure as it picked up iris pigment as it migrated around the anterior chamber. Accordingly, we explored delivery of the implant in the middle segment behind the iris and in front of the pseudophakic lens. We then evaluated the suitability of various imaging modalities to assess the implant in this location. For middle segment administration, the ArcScan Insight 100 robotic ultrasound provided resolution and repeatability sufficient to monitor the implant behind the iris. This preliminary study hypothesizes that DURYSTA migration in the anterior chamber is the main source of AEs. Through use of a confined location, the middle segment, the implant is unlikely to migrate and cause CEC loss while also delivering drug closer to its site of action, the ciliary body. Further efforts are underway to understand the suitability of the middle segment for serial DURYSTA administration to maximize intraocular pressure lowering while minimizing AEs.

Dermal wound healing describes the progressive repair and recalcitrant mechanism of damaged skin and eventually reformatting and reshaping the skin. Many probiotics, nutraceuticals, metal nanoparticles have been associated with improved healing process of intra and inter tissue wounds. Despite the vast nature on material based wound healing mediators, the exact mechanism on material-cellular interaction is still point of repent issue particularly in diabetics and pathological condition. The use of bioengineered alternative agents will likely only continue to dominate the outpatient and perioperative management of chronic, recalcitrant wounds as new additional products continue to cut costs and improve wound healing process. This review article provides an update of the various remedies with confirmed wound healing activities by a diverse group of agents from previous experiments conducted by various researchers

Background: The treatment plan of prosthetic restorations supported by dental implants require comprehensive scientific knowledge to deliver prostheses with good prognosis, even before the implant insertion. This review aims to analyze the main prosthetic determinants of the prognosis of implant-supported prostheses. Methods: A systematic review of the literature was conducted with a PICO question: "For partially or complete edentulous subjects treated with implant-supported prostheses, which prosthetic factors could affect clinical outcomes?". A literature search was performed electronically in PubMed (MEDLINE), Scopus and Cochrane Library with the following equation [PROGNOS* OR RISK] FACTOR IMPLANT DENTAL, and by hand search in relevant journals and throughout the selected papers. Results: This revision was carried out based on 50 papers focused on several prosthodontics-related risk factors that were grouped as follows: implant-connection, loading protocol, transmucosal abutments, prosthetic fit, provisionalization, type of retention, impression technique, fabrication technique, and occlusion. More than a half of the studies were systematic reviews (30%), meta-analysis (16%) or prospective evaluations of prosthesis with various kinds of events (18%). But also narrative reviews of literature (14%) and in vitro/animal studies (16%) were found. Conclusions: The current literature provides insufficient evidence for most of the investigated topics. However, based on the accumulated data, it seems reasonable to defend that the best treatment approach is the use of morse taper implants with transmucosal abutments, recorded by means of rigidly splinted copings through the pick-up technique, and screwed by milled prosthesis occlusally adjusted to minimize functional overloading.

This systematic review investigates the failure rate and marginal bone loss (MBL) of dental implants placed in Solid-organ transplant (SOT) patients compared to healthy controls. Three databases (PubMed, Web of Sciences and the Cochrane Library) were searched up to June 2020 (PROSPERO CRD42019124896). Case-control and cohort studies reporting data failure rate and marginal bone loss (MBL) of dental implants placed in SOT patients were included. The risk of bias of observational studies was assessed through the Newcastle-Ottawa Scale (NOS). Four case-control studies fulfilled the inclusion criteria, all of low risk of bias. Meta-analyses revealed consistently lower implant failure rate than control populations at patient and implant levels. SOT patients had a significant difference of -18% (p-value <0.001) of MLB towards healthy patients. SOT status poses no serious threat to implant survival. Overall, this group of patients presented lower levels of dental implant failure rate and marginal bone loss compared to otherwise healthy patients. Further intervention trials with wider sample size and longer follow-ups are necessary to confirm these summary results.

One of the most popular techniques for determining electrical properties of material is the free-space measurement technique. With the potential for new applications requiring efficient, accurate and broadband material measurement systems using higher millimeter-wave and terahertz frequencies, the free-space measurement method has received renewed interest. This is mainly due to its simplicity, favorable properties as a non-destructive method, and it allows transmission and reflection measurements without any physical contact with the sample. This paper reviews and discusses state- of-the-art free space material measurement systems, starting with the different measurement techniques available for material characterization, their important concepts, post-processing in determining their properties, and progress towards expanding their use at higher frequencies. Also, this paper reviews dielectric material characterization using the free space method focusing on their application extension towards the higher frequencies. Besides, the algorithms for conversion methods and usage of lens in free space material measurement system was discussed in this paper. Finally, a future perspective on the outlook of this free space method is presented prior to the conclusion.